DESIGN & IMPLEMENTATION OF A

SOLAR POWER SYSTEM

This Project is Submitted to the Department of Electrical and Electronic

Engineering (EEE) in Partial Fulfillment of the Requirement for the Degree of
Bachelor of Science in Electrical & Electronic Engineering.

SUPERVISED BY
MD. MAHMUDUR RAHMAN
SENIOR LECTURER

SUBMITTED BY:
1. ARIFUL HAQUE SAYEM ID: 103-33-367
2. SHAHEDUL HASAN
ID: 103-33-342

DEPARTMENT OF ELECTRICAL & ELECTRONIC ENGINEERING

DAFFODIL INTERNATIONAL UNIVERSITY

OCTOBER 08, 2013

DECLARATION
We hereby declare that, this project has been done by us under the supervision of
Md. Mahmudur Rahman, Senior Lecturer, Department of EEE, Daffodil
International University. We also declare that neither this project nor any part of
this project has submitted elsewhere for award of any degree or diploma.

Supervised by:

Md. Mahmudur Rahman

Senior Lecturer
Department of EEE
Daffodil International University

Submitted by

Ariful Haque Sayem

Md.Shahedul Hassan

ID:103-33-367

ID: 103-33-342

Department of EEE

Department of EEE

Daffodil International University

Daffodil International University

II

ACKNOWLEDGEMENT:

First we express our heartiest thanks and gratefulness to almighty Allah for His
divine blessing makes us possible to complete this project successfully.

We are grateful and wish our profound our indebtedness to Md. Mahmudur
Rahman, Department of EEE Daffodil International University, Dhaka. Deep
theoretical and hardware knowledge & keen interest of our supervisor in this field
influenced us to carry out this project. His endless patience, scholarly guidance
,continual encouragement, constant and energetic supervision, constructive
criticism, valuable advice, reading many inferior draft and correcting them at all
stage have made it possible to complete this project.

We would like to express our heartiest gratitude to honorable Head, Department of

EEE, for his kind help to finish our project and also to other faculty members of
EEE department of Daffodil International University.

III

ABSTRACT
The world is using all the resources to meet the daily demands of energy and it is
quite expectable that in the near future we will run out of any natural resources like
ore/mineral/petroleum etc.

As a result, renewable energy solution has achieved a great demand today to save
the natural resources and also to tackle the crisis of energy. Solar energy is rapidly
gaining its popularity as an important source of renewable energy.

In this project a basic solar power system has been designed.

IV

Contents
Contents
no

Preface

Chapter-1
Inroduction

Page
no
1-7

1.1

Introduction

1.2

Definition of Energy

1.3

Renewable Energy

1.4

Types of Renewable Energy

1.5

Advantages of Renewable Energy

6
8-11

Chapter-2
Renewable Energy in Bangladesh
2.1

Renewable Energy Technologies Suitable for Bangladesh

2.2

Present Scenario of Conventional and renewable energy

2.3

Significant Progress of Renewable Energy Technology in

Bangladesh

10

2.4

Government Support in Renewable Energy Sector in

Bangladesh

11

2.5

Ongoing Renewable Energy Technology (RET)Projects in Bang

ladesh

11

Chapter-3
Energy and Sun

12-18

3.1

Definition of Energy

13

3.2

Types of Energy

13

3.3

Sun

13

3.4

Surface temperature

14

3.5

Conversion of sunlight into electricity

14

3.6

Extraterrestrial radiation

15

3.7

Equation of time

16

3.8

Solar Energy Spectrum

17

Chapter-4
Aspects of Solar Energy in Bangladesh

19-24

4.1

Solar energy uses

20

4.2

Solar Photovoltaic

20

4.3

Solar Heating

21

4.4

Solar Thermal Electricity

22

4.5

Solar Cooking

23

4.6

Solar Water Heater

23

4.7

Solar dryer

24

Chapter-5
Solar PV Equipment
5.1

Solar cells

25-41

26

5.1.1 Connect cell to make modules

26

5.1.2 Types of Solar Cells

27

5.1.2.1 Monocrystalline Cells

27

5.1.2.2 Polycrystalline Cells

28

5.1.2.3 Amorphous Cells

29

5.2

Charge Controller

29

5.2.1 Function of charge controller

30

5.2.2 Block diagram of processing of charge controller

32

5.2.3 Types of Charge controller

32

5.2.3.1 Parallel Controller

33

5.2.3.2 Series Controller

34

5.3

5.2.4 Panel charging and characteristics of control

35

5.2.5 Charge Controller Operation

36

5.2.6 Selection of charge controller

37

5.2.7 Voltage setting of controller

37

5.2.8 MPPT Charge controller

38

Battery

38

5.3.1 Battery Storage

38
VI

5.4

Inverter

39

5.4.1 Applications

40

5.4.2 String inverter

40

5.4.7 Power plant inverter

41

5.4.8 Grid tie inverter

41

Chapter-6
Solar System Design
6.1

Solar home system design

41-52

42

6.1.1 Flow chart of solar home system design process

43

6.1.2 Site screening

44

6.1.3 Load determination

44

6.1.4 Battery sizing

44

6.1.5 Array sizing

44

6.1.6 Selection of charge controller

44

6.1.7 Selection of converter

45

6.1.8 System wiring

45

6.1.9 A small size 12 volt home system Design

46

6.1.10 A big size 24 volt home system Design

48

6.1.11 Design of 50 watt solar PV system

50

6.1.12 Design of 60 watt solar PV system

51

6.1.13 Design of 110 watt solar PV system

52

Chapter-7
10 watt solar power system

53-60

7.1

MATERIALS

54

7.2

Tools

54

7.3

Dimensional Information

55

7.4

Connection Diagram

55

7.5

Specifications

56
VII

7.6

Work Procedure

57

7.7

Connection Diagram

57

7.8

Load calculation

58

Project Picture

58-60

Chapter 8
Conclusion
Conclusion

62

Reference

63

VIII

LIST OF FIGURES

Serial

NAME

PAGE

Renewable energy

Hydro plant

Wing energy

Present Scenario of Conventional and renewable

The sun

13

Sun -Earth relation-1, Earth relation-2

Extraterrestrial radiation

16

Solar Energy Spectrum, Spectrum of Solar Radiation

17

Angles to define the position of the sun and the orientation of a tilted
plane.

18

10

The family living in this house enjoys hot water heated by the sun
with a solar thermal system.

21

13

Solar cooking dish, Solar water heating mechanism.

23

14

Amorphous solar, Polycrystalline solar cell, Single Crystal solar cell.

27

15

Charge controller.

30

16

Block diagram of processing of charge controller.

32

17

Use of Shunt controller in solar home system

33

18

Use of Shunt controller in solar home system.

34

19

Relation between different types of charge controller and battery

voltage and current.

35

20

Point of controller (Micro-controller based).

36

IX

14,15

21

A solid state series controller and its various parts.

37

22

Phocos MPPT 100/20(20 amps).

38

23

12 volt, 100 Ah solar battery.

39

24

String inverter.

40

25

Power plant inverter.

41

26

Inverter for grid connected PV.

41

27

A typical solar home system design.

42

28

Dimensional Information.

55

29

Connection Diagram

55

29

10 watt solar power system.

57

30

Project picture( Solar panel, Side view).

59

31

Project picture (Charge Controller, Internal View).

60

Chapter-1

1.1 Introduction:
A most important & significant look in our modern civilization is energy
of different
forms. Many necessary functions can be at a stand still with out energy. So energy is a part of
our life. There are various form of energy consumption process such raw energy in falling
water, in deposits of coal, oil and gas etc are most well known form.
Energy sources which are regenerated after a regular time cycle are commonly known as
renewable sources of energy like hydro power, solar energy, wind energy, tidal energy,
biomass fuels etc. In a particular location available renewable energy sources are finite
quantity, which depends on their respective characteristics feature. When renewable energy
sources is extracted at a higher rate then its regenerative rate is becomes non renewable.
Energy produced from renewable natural resources & technologies.
The present energy demand is increasing day by day in Bangladesh due to various reasons
such as increasing population, the aspiration for improved living standard and general
economic and industrial growth. The power generation system is principally depended on
imported petroleum oil and own natural gas. On the other hand, as the information about the
deposits of fossil fuels in Bangladesh, if they are consumed at the present rate, the reversed
natural gas and coal will be exhausted by the year 2020 to 2030. To reduce the dependency
on imported fuel and the pressure on natural gas, the present power generation system must
be diversified and at the same time indigenous energy resources have to be explored and
developed. It may be mentioned that concern for environment is a now a universal issue and
conventional energy gives rise to greenhouse gases with adverse consequences for health and
climate. In these perspectives, harnessing of renewable energies and development of relative
technologies is a highly important strategic option. Communities in rural areas and mainly in
remote areas of Bangladesh have very little possibilities to participate on the national
electricity supply. Therefore, and in the context of environment protection, renewable
energies can contribute substantial to the delivery of alternative energy to the users etc. are
some of the key issues that determine the need for technological inventions in solving energy
problems in the rural areas.

1.2 Definition of Energy:

Energy:
Energy is the measure of a physical system. It defines the quality of the changes and
processes, which take place in the Universe, beginning with movement and finishing with
thinking.

1.3 Renewable Energy:

Renewable energy is energy generated from natural resources such as sunlight, wind, rain,
tides, and geothermal heat which are renewable (naturally replenished). In 2006, about 18%
of global final energy consumption came from renewable, with 13% coming from
traditional biomass, such as wood-burning. Hydroelectricity was the next largest renewable
source, providing 3% of global energy consumption and 15% of global electricity generation.
Wind power is growing at the rate of 30 percent annually, with a worldwide installed capacity
of 121,000 megawatts (MW) in 2008, and is widely used in European countries and
the United States. The annual manufacturing output of the photovoltaic industry reached
6,900 MW in 2008, and photovoltaic (PV) power stations are popular in Germany and
Spain. Solar thermal power stations operate in the USA and Spain, and the largest of these is
the 354 MW SEGS power plant in the Mojave Desert. The world's largest geothermal
power installation is The Geysers in California, with a rated capacity of 750 MW. Brazil has
one of the largest renewable energy programs in the world, involving production of ethanol
fuel from sugar cane, and ethanol now provides 18 percent of the country's automotive fuel.
Ethanol fuel is also widely available in the USA. While most renewable energy projects and
production

is large-scale, renewable

technologies

are

also

suited

to small off-grid

applications, sometimes in rural and remote areas, where energy is often crucial in human
development. Kenya has the world's highest household solar ownership rate with roughly
30,000 small (20100 watt) solar power systems sold per year. Some renewable-energy
technologies are criticized for being intermittent or unsightly, yet the renewable-energy
market continues to grow. Climate-change concerns, coupled with high oil prices, peak oil,
and increasing government support, are driving increasing renewable-energy legislation,
incentives and commercialization.New government spending, regulation and policies should
help the industry weather the 2009 economic crisis better than many other sectors.

Main forms/sources of renewable energy

Figure: Renewable energy,end of 2008(GW)

1.4 Types of Renewable Energy

Biomass
Geothermal Energy
Wind Energy
Photovoltaic (PV) Cells
Hydropower

Hydropower:
Hydropower is the largest source of renewable energy. This renewable source of energy
provides 10% of the nations electricity. As of now, there are 77,000 Megawatts of
hydropower, enough to provide 35 million homes with energy. Converting flowing water into
3

usable energy produces hydropower. Most of this water comes from rivers and is released
through turbines to produce energy. Although this power source does not release pollution, it
can possibly harm fish and wildlife, displace people, and alter the quality of water. Better
technology is trying to reduce the loss of aquatic life, but the problem with this technology is
that it is highly expensive and takes a long time to build.

Figure: Hydro Power

Biomass/Bio energy:

Biomass makes up about 7,000 Megawatts of renewable electricity. Biomass fuels stem from
industrial processing, such as forestry and wood products, agriculture and wood products, and
construction and transportation. Biomass can replace coal in power plants because it produces
less sulfur dioxide than coal. Mill operations seem to be the main source of biomass energy in
the U.S. Europe, on the other hand, draws its main source of bio energy from urban wood
waste. Third world countries make timber their main source of bio energy. According from
statistics from the International Energy Agency, 11% of the world derives its energy from
biomass. Developing countries use about 35%, while the poorest ones use roughly 90%. One
way to convert biomass into usable energy is through gasificationconverting biomass to
gas and burning it in a gas turbine.

Wind Energy:
Wind energy produces about 2,500 Megawatts of energy, and generates a mere .1% of our
electricity. The wind rotates blades around a hub, which is connected to the main shaft. The
main shaft spins a generator. The size of turbines is determined by how much energy is
needed. Small wind turbines are usually used for homes, farms and ranches. Other ways to
use wind energy include grinding grain and pumping water.
Wind is classed in categories of 1 through 7, with 7 being the highest and 1 being the lowest.
A good wind source that has a class of 3 or higher is the east coast and along the Appalachian
Mountains. North Dakota is an excellent wind source.
The disadvantages of wind energy are that again, the technology is very expensive, the
machinery is known to be noisy, birds have been killed by running into the turbines, and the
wind might not be present at certain times throughout the year.

Fig: Wind Energy

Photovoltaic (PV) Cells:

Solar Module:
PV cells produce electricity from sunlight. Materials used in computer chips are similar to
materials used in PV cells. These materials absorb sunlight, which frees the electrons from
their atoms and allows them to generate electricity. PV cells are great because they dont
require high maintenance, are very reliable, and dont produce pollutants.

Geothermal Energy:
Geothermal energy is capable of producing about 2,800 Megawatts of energy per year, 0r
roughly .2% of the energy in the U.S. Geothermal energy is produced from naturally
occurring steam and hot water from under the Earths surface. The steam rotates a turbine,
which in turn powers an electric generator. Also, hot water can be used to directly heat
building. The downside to geothermal energy is that land sites is very hard to find and
extremely rare. A positive fact is that geothermal energy is very cost effective and reliable.

1.5 Advantages of Renewable Energy:

With the goal of reducing air pollution and advancing public health, renewable energy
methods like solar and wind are being embraced around the world. Renewable energy has
several environmental and economic benefits.

Environmental Benefits:
Because renewable energy sources like solar and wind do not require the use of fossil fuels,
they do not emit carbon dioxide. Carbon dioxide is a bi-product of burning coal and gas. By
reducing the amount of fossil fuels we burn, we are decreasing the amount of pollutants and
chemicals being emitted into the atmosphere.

Wind Energy:
Electricity generated by wind through turbines is a fast-growing renewable energy source
around the world. These turbines can be placed on land or offshore. One turbine can create
enough energy to power 500 homes that use average levels of electricity.

Solar:
Solar energy is generated through the sun's heat. To put into context the immense power of
the sun, the entire supply of coal, oil and natural gas is equivalent to the power put off by the
sun in just 20 days. This energy can be harnessed through the use of photovoltaic solar panel
that can be put on roofs, atop building and even on cars.

Public Health:
Pollution coming from power plants taints our air supply and causes asthma. Through the use
of renewable energy, we could eliminate these harmful substances in the air, leading to a
healthier population.
6

Cost and Supply:

Once the solar panels are installed and the windmills are put up, renewable energy is
essentially free. It costs nothing to use the suns rays, and taking advantage of a windy day is
free. Furthermore, the supply of wind is not going to diminish. The sun's rays are also
prevalent and will exist for millions of years.

Chapter 2
Renewable Energy in Bangladesh

2.1 Renewable Energy Technologies Suitable for Bangladesh:

Different types of renewable energy technologies (RET) applications suitable for Bangladesh are
described in the subsequent headings.
Solar Thermal
Solar photovoltaic (SPV)
Biomass
Small Hydro
Waste Energy

2.2 Present Scenario of Conventional and renewable energy(Electric power)

Utilization in Bangladesh:

Bangladesh Total insulated power in grid electricity is 5254 MW

Hydro

230 MW

Furnace Foil

280 MW

Coal

250MW

Diesel

200MW

Gas

4285MW

Total insulated power off grid electricity

is 22.55 MW
Micro Hydro

0.1MW

Biomass/Biogas

0.5MW

Wind

2.5MW

Solar

18.55MW

2.3 Significant Progress of Renewable Energy Technology in Bangladesh:

Total installed Power for off grid electricity is 20 MW from RE
Technology

Capacity

Implementing

Financial partner

Agency
Solar PV stand

365,000 SHS and

14 partner

IDCOL (World

alone system with

its integrated

organizations of

Bank, GEF, GTZ

ownership model

capacity is 18.5

IDCOL like RSF,

and KFW, ADB,

MW

GS, BRAC etc.

IDB)

6000 SHS

REB

World Bank, GEF,

Solar PV stand
alone system (fee

GTZ and French

for services)

grant

Centralized PV

300 KW

LGED , BPDB

UNDP, GOB

Micro Hydro

10KW

LGED

UNDP

Biomass/biogas

400 KW

Private/Public

IDCOL, GTZ

Wind

2.5 MW

BPDB

UNDP, WB

Improved Cooking

80,000 nos

Pos of GTZ

GTZ

system

Stove

Source: www.reein.org

10

2.4 Government Support in Renewable Energy Sector in Bangladesh:

Sector

Opportunity

Government policy

Government setup a target that at least 5% electricity by

2015 and 10% by 2020 will be generated from RE

Duty & VAT

Government wipe out all sort of duty from renewable

energy commodities

Tax Holiday (according to

RE policy)

According to declared RE policy, Renewable energy

Manufacturing plant for

PV module

company will enjoy 5 years tax holiday from its inception

however current budget doesn't support it
Duty of capital machinery for assembling of PV module is
exempted.

2.5 Ongoing Renewable Energy Technology (RET)

Projects in Bangladesh:
Renewable energy development project- REB/IDCON.
Sustainable rural energy- LGED
Solar & Wind resource assessment project- RERC, DU
SHS project- Grameen Sakti.
PREGA- REB/BPDB
GTZ funded project REB.
Biogas pilot project LGED.
RET in Asia- CMES/KUET
SHS project- BRAC.
CHT SHS project- BPDB.
RET feasibility study- BCSIR.
SHS project-TMSS.
Solar home lighting system- Centre for mass education in science (CMES) Solar home systemIntegrated Development Foundation (IDF)
Wind power generation- BPDB
Hybrid system- Grameen Sakti, BRAC.
11

Chapter 3
Energy and Sun

3.1 Definition of Energy:

Energy is the measure of a physical system. It defines the quality of the changes and
processes, which take place in the Universe, beginning with movement and finishing with
thinking. The unity and the connection between the movement forms of substance, their
lively capacity of mutual transformation, allowed the measuring of different forms of
substance through a common aspect: energy.

3.2 Types of Energy:

The name of energy forms is related to:
1.The way energy is perceived (for example: mechanical energy, electrical energy, energy of
light)
2.What carries the energy (for example: thermal energy)
3.The origins of energy (for example: nuclear energy, hydraulic energy, wind energy ,
geothermal energy, and solar energy).

3.3 Sun:
The Sun

figure : The source of all energy

13

3.4 Surface temperature:

We know that the sun is a sphere of diameter 1,400,000 km, that its outer regions are hot
gases, mostly hydrogen and helium, and that its surface temperature is about 6,000 degrees
Celsius (about 11,000 degrees Fahrenheit). Any surface at that temperature will generate heat
and light. The burners of an electric stove or a toaster oven, for example, are not at 6,000 C.,
but when they're turned on they are "red hot"; they emit heat and light and the light is red. If
we could raise the temperature to 6,000 C. they would become "white hot", and emit light
very much like the sun's. Similarly, a fire is a region of gases at a temperature high enough to
generate heat and light.
So the question becomes not so much why is there heat and light, but where does the energy
come from to keep the surface temperature of the sun at 6,000 degrees?

3.5 Conversion of sunlight into electricity:

Light knocks loose electrons from silicon atoms. Free electrons have extra energy. Internal
electric field (junction) pushes electrons to front of cell. Electric current flows on to other
cells or to the load. Cells never run out of electrons.

Sun -Earth relation-1

14

Sun Earth Relation-2

3.6 Extraterrestrial radiation

It is also important to know the spectral distribution of extraterrestrial radiation, i.e. the
radiation that would be received in the absence of atmosphere. The extraterrestrial solar
spectrum at mean earth sun distance can be divided into following three main regions, usually
divided into wave bands (1 micron = 1m = 10-6, mm = 10-6 meter).
.Ultraviolet region (l < 0.38 mm). Percentage of solar radiation 7%. Visible region (0.38 < l <
0.78 mm) Percentage radiation 47.3%.

15

Figure: Extraterrestrial radiation

Extraterrestrial radiation at any time of the year is given by
360 n

Ion = Isc 1 0.033cos

365
where Isc is the solar constant and Ion is the extraterrestrial radiation measured on a plane
normal to the radiation on then day of the

year counted from January 1st as n=1.Solar

Constant is defined as the energy from the sun received on a unit area of the surface
perpendicular to radiation at mean earth sun distance. WRC adopted a value of 1367W/m2

3.7 Equation of time:

E = 229.2(0.000075+0.001868 B- 0.032077 sin B - 0.014615 cos 2B- 0.04089sin2B)Where,
B = (n-1)360/365 and n is the day of the year.
Monthly averaged daily global radiation (kWh/m2/day)
Jan

Feb Mar Apr May Jun Jul

Aug Sep Oct Nov Dec Average

4.02

4.64 5.01 5.37 4.83 4.22 4.00 4.13 4.15 4.23 4.04 3.80 4.37

16

3.8 Solar Energy Spectrum:

Figure :Spectrum of Solar Radiation

Figure :Defintion of the angles for the description of the position of the sun

17

Figure : Angles to define the position of the sun and the orientation of a tilted

18

Chapter 4
Aspects of Solar Energy in Bangladesh
4.1Solar energy uses:
Solar energy uses in various respects. Such as;
Generate electricity using photovoltaic solar cells.
Generate electricity using concentrated solar power.
Generate electricity by heating trapped air, which rotates turbines in a solar updraft tower.
Heat buildings, directly, through passive solar building design.
Heat foodstuffs, through solar ovens.
Heat water or air for domestic hot water and space heating needs using solar- thermal panels.
Heat and cool air through use of solar chimneys.
Generate electricity in geosynchronous orbit using solar power satellite.
Solar air conditioning.
4.2Solar Photovoltaic:

4.2.1 Photovoltaic:
Becquerel first discovered that sunlight could be converted directly into electricity in
1839, when he observed the photogalvanic effect. But the first solar cell, developed by Chapin,
Fuller and Pearson, revealed in 1954. It had an efficiency of 6% only. In 1956, the invention
of 10% efficient silicon solar cell was reported. Only two years later, the first solar cells were
used on the Vanguard I orbiting satellite. Since then, the use of solar electricity (also known as
photovoltaics) is going on increasing year by year and some have been in continuous outdoor
operation on Earth or in space for over 30 years.

4.2.2 Advantages of Photovoltaic:

Photovoltaic has shown, since the 1970s, that the human race can get a substantial portion of its
electrical power without burning fossil fuels (coal, oil or natural gas) or creating nuclear fission
reactions. Photovoltaic helps us avoid most of the threats associated with our present techniques
of electricity production and also has many other benefits. Photovoltaic has shown that it can
generate electricity for the human race for a wide range of applications, scales, climates, and
geographic locations. It can provide electricity to remote transmitter stations in the mountains

20

allowing better communication without building a road to deliver diesel fuel for its generator. It
can supply electricity to the community in an island, which is very far from utility grid, or can
supply electricity to the people of poor countries like African countries, where people are
scattered and grid electricity is not feasible.Fossil-fuel plants have many disadvantages: a wide
range of environmentally hazardous emissions, parts which wear out, steadily increasing fuel
costs, they are not modular (deployable in small increments), and they suffer low public opinion
(no one wants a coal burning power plant in their neighborhood). Photovoltaic suffers none of
these problems. Some other advantages of photovoltaic are given belowFuel source of photovoltaic is vast and essentially infinite.No emissions, no combustion or
radioactive fuel for disposal.

Low operating cost.

No moving parts.
No high temperature corrosion or safety issue.
High reliability in modules (>20 years).
Completely modular (small or large increment is possible).
Quick installation.
Can be integrated into new or existing building structures.
Can be installed at nearly any point-of-use.
Daily output peak may match local demand.
High public acceptance.
Excellent safety record.

4.3 Solar Heating:

Figure : The family living in this house enjoys hot water

heated by the sun with a solar thermal system

21

Solar heating harnesses the power of the sun to provide solar thermal energy for solar hot
water, solar space heating, and solar pool heaters. A solar heating system saves energy, reduces
utility costs, and produces clean energy. The efficiency and reliability The family living in this
house enjoys hot water heated by the sun with a solar thermal system
of solar heating systems have increased dramatically, making them attractive options in the
home or business. But there is still room for improvement.

4.3.1 Solar Heating Basics:

Solar heat can be used for solar water heating, solar space heating in buildings, and solar pool
heaters. Solar water heaters and solar space heaters are constructed of solar collectors, and all
systems have some kind of storage, except solar pool heaters and some industrial systems that
use energy "immediately." The systems collect the sun's energy to heat air or a fluid. The air or
fluid then transfers solar heat directly to a building, water, or pool.

4.3.2 Solar Heating in Use:

Since the early 1970s, the efficiency and reliability of solar heating systems and collectors have
increased greatly, and costs have dropped. Today's solar thermal systems are used for solar
water heating, solar pool heating, and in solar space heating.

4.4 Solar Thermal Electricity:

Solar energy can also be used to make electricity. Some solar power plants, like the one in the
picture to the right in California's Mojave Desert, use a highly curved mirror called a parabolic
trough to focus the sunlight on a pipe running down a central point above the curve of the
mirror. The mirror focuses the sunlight to strike the pipe, and it gets so hot that it can boil water
into steam. That steam can then be used to turn a turbine to make electricity.In California's
Mojave Desert, there are huge rows of solar mirrors arranged in what's called "solar thermal
power plants" that use this idea to make electricity for more than 350,000 homes. The problem
with solar energy is that it works only when the sun is shining. So, on cloudy days and at night,
the power plants can't create energy. Some solar plants are a "hybrid" technology. During the

22

daytime they use the sun. At night and on cloudy days they burn natural gas to boil the water so
they can continue to make electricity.

4.5 Solar Cooking:

Solar cookers use sunlight for cooking, drying and pasteurization. Solar cooking offsets fuel
costs, reduces demand for fuel or firewood, and improves air quality by reducing or removing a
source of smoke. Concentrating solar cookers use reflectors to concentrate light on a cooking
container. The most common reflector geometries are flat plate, disc and parabolic trough type.
These designs cook faster and at higher temperatures (up to 350 C) but require direct light to
function properly.

Figure : Solarcooking dish

4.6 Solar Water Heater:

Where heat from the Sun is used to heat water in glass panels in our roof. This means we don't
need to use so much gas or electricity to heat our water at home. Water is pumped through pipes
in the panel. The pipes are painted black, so they get hot when the Sun shines on them. Many
homes used solar water heaters.

Figure: Solar water heating mechanism

23

Today, solar water heaters are making a comeback. They heat water for use inside homes and
businesses. They also heat swimming pools like in the picture. Panels on the roof of a building,
like this one on the right, contain water pipes. When the sun hits the panels and the pipes, the
sunlight warms them.

4.7 Solar dryer:

Agricultural and other products have been dried by the sun and wind in the open air for
thousands of years. The purpose is either to preserve them for later use, as is the case with food;
or as an integral part of the production process, as with timber, tobacco and laundering. In
industrialized regions and sectors, open air-drying has now been largely replaced by mechanized
dryers, with boilers to heat incoming air, and fans to force it through at a high rate. Mechanized
drying is faster than open-air drying, uses much less land and usually gives a better quality
product. But the equipment is expensive and requires substantial quantities of fuel or electricity
to operate.

4.7.1 Solar dryer Application:

For centuries people of various nations have been preserving dates, figs, apricots, grapes,
bananas, pineapples, other fruits, herbs, cassava, yams, potatoes, corn, peas, onions, garlic,
carrots, peppers, milk, coffee, meat, and fish by drying.
But drying is also beneficial for hay, copra (kernel of the coconut), tea and other income
producing non-food crops. It is worth noting that until around the end of the 18th century when
canning was developed, drying was virtually the only method of food preservation.

4.7.2 Solar Drying Can Improve Agricultural Products:

Dehydration of vegetables and other food crops by traditional methods of open-air sun drying is
not satisfactory, because the products deteriorate rapidly. Furthermore, traditional methods do
not protect the products from contamination by dirt, debris, insects, or germs. A study by
Akwasi Ayensu from the Dept. of Physics at the University of Cape Coast, Cape Coast, Ghana
demonstrates that food items dried in a solar dryer were superior to those which were sun dried
when evaluated in terms of taste, color, and mould counts. He asserts, and many others agree
that solar drying systems must be developed to utilize this energy resource to improve food
preservation. This translates into quality products that can be stored for extended periods, easily
transported at less cost while still providing excellent nutritive value.

24

Chapter 5
Solar PV Equipment

5.1 Solar cells:

Photovoltaic (PV) or solar cells are PN junction Semiconductor devices. It converts sun light
into direct current electricity. Groups of solar cells are electrically connected into PV
modules, arrays. PV modules or arrays can be used to charge batteries .This system can be
used to power any number of Electrical loads. PV systems can produce alternating currents or
Inverter. Compatible with any conventional appliances and operate in parallel with and
interconnected to the Utility grid.
Solar cells often are distinguished by their type of semiconductor junction(A)Homojunction (n + p layer is of the same material)
(B)Heterojunction (n + p layer is of different material)
(d)MIS (Metal / Isolator / Semiconductor
(e)SIS (Semiconductor / Isolator / Semiconductor)

5.1.1 Connect cell to make modules:

One silicon solar cell produces 0.5V to 0.6V

Usually 36 cells are connected together to make a Module

Such one module has enough voltage to charge 12 volt batteries and Run pumps and
motors

PV Module is basic building block of a PV power system

Modules can be connected to produce more power

26

Figure 1 : Cells, Modules, Panels and Arrays

5.1.2 Types of Solar Cells:

Solar cells can be classified according to semiconductor materials of the cell, according to the
crystalline structure of the material, and according to the number of
junctions of the cell. According to the crystalline structure of the material there are three
types of solar cells.
1. Single-crystalline or mono crystalline cells
2. Multi-crystalline or polycrystalline cells and
3. Amorphous cells

Fig : Amorphous solar Polycrystalline

Single Crystal

5.1.2.1.Monocrystalline Cells
Monocrystalline cells are the most important type, because they have the highest conversion
efficiency (25%), and the base material, which is extremely pure silicon, is already well
established in the field of semiconductor production. Currently, the methods of producing
silicon single-crystals are primarily either the Czochralsky process or the floating zone
technique. In the Czochralsky process, monocrystalline silicon grows on a seed, which is
pulled slowly out of the silicon melt. With both methods, silicon rods are produced, which are
cut into slices of 0.2 to 0.4 mm thickness. The discs (wafers) produced in this way, then,
undergo several further production steps. These are, for instance:

27

a. Grinding and cleaning

b. Doping
c. Metallization
d. Antireflection coating

Figure: Monocrystalline Cells

5.1.2.2 Polycrystalline Cells:

The manufacturing process for monocrystalline silicon is highly energy-intensive and
therefore very expensive. For this reason, in many cases polycrystalline silicon (Poly- Si) is
preferred. Poly-Si develops, when a silicon melt is cooled down slowly and controlled. The
yielded silicon ingot is sliced and further processed, as described before. The pulling of the
single-crystal can be omitted this way. Inside the Poly-Si crystal, there are crystalline regions,
which are separated by grain boundaries. The losses occurring at these grain boundaries cause
the lower efficiency (less than 20%) of polycrystalline cells compared with monocrystalline
ones. Despite this disadvantage, the importance of polycrystalline cells is growing, because
of the lower production costs.

Figure: Polycrystalline Cells

28

5.1.2.3 Amorphous Cells:

In order to avoid the energy-intensive production process mentioned above, and to avoid the
cutting loss of the slicing process, a vapor-phase technique has been developed in which a
thin film of silicon is deposited from a reactive gas such as silane (SiH4) on a carrier material
like glass and doped in a further step. The semi conducting material grown in this way is
called amorphous silicon. This technology has two disadvantages: first, the conversion
efficiency is considerably low, i.e., less than 10%; second, the cells are affected by a
degradation process during the initial months of operation, which reduces the efficiency
furthermore.
These disadvantages are compensated by the Relatively simple and inexpensive manufacturing process
The possibility of producing cells with a larger area
The lower energy consumption and
Easy to use in small electronic equipment.

Figure : Amorphous Cells

5.2 Charge Controller:

Charge controller is an electronic device which is used in solar system. A solar charge
controller is needed in virtually all solar power systems that utilize batteries.
The job of the solar charge controller is to regulate the power going from the solar panels to
the batteries. Overcharging batteries will at the least significantly reduce battery life and at
worst damage the batteries to the point that they are unusable.
29

The most basic charge controller simply monitors the battery voltage and opens the circuit,
stopping the charging, when the battery voltage rises to a certain level. Older charge
controllers used a mechanical relay to open or close the circuit, stopping or starting power
going to the batteries. Modern charge controllers use pulse width modulation (PWM) to
slowly lower the amount of power applied to the batteries as the batteries get closer and
closer to fully charged. This type of controller allows the batteries to be more fully charged
with less stress on the battery, extending battery life. It can also keep batteries in a fully
charged state (called float) indefinitely. PWM is more complex, but doesnt have any
mechanical connections to break.
The electricity produced in the solar panel is stored in the battery. The electricity stored in the
battery is used at night. This whole process is monitored by the charge controller.
A typical charge controller (Phocos) is shown in the figure bellow-

Figure: Charge controller

5.2.1Function of charge controller:

The main function of a charge controller or regulator is to fully charge a battery without
permitting overcharge while preventing reverse current flow at night. Other functions are

Stop the process of the battery when it is fully charged.

Disconnect the load during low voltage.

Disconnect the load during high voltage.

Monitor the battery voltage, state of charge, SOC etc.

To give alarm during fault condition.

Current measurement.
30

Detect when no energy is coming from the solar panels and open the circuit,
disconnecting the solar panels from the batteries and stopping reverse current flow.

Charge controller is used for co-ordination and control among the battery, load and
solar panel. Charge controller stores the electricity in the battery during day time and
supplies the same to the load (mainly lamp) at night. On the other hand, if battery is fully
charged, Then charge controller can directly supply electricity to the load (Fan, mobile
charger etc) from the solar panel during day time.
A charge controller or charge regulator is mainly worked as a voltage regulator. Generally it
controls the voltage and current of the solar panel to save in battery. Solar panel mainly
produces 16 volts to 21 volt and 14 volt to 14.4 volt is required to keep the battery in full
charged state. The charge controller woks as a Buck converter
to minimize this voltage
level. Charge controller is mainly a Chopper
or DC-DC converter. Buck converter is
usually used in the solar panel which converts the high level DC voltage to the low level DC
voltage.

31

5.2.2 Block diagram of processing of charge controller:

Figure: Block diagram of processing of charge controller

5.2.3 Types of Charge controller:

Charge controller connection mainly two types1. Parallel or shunt controller
2. Series controller

32

5.2.3.1 Parallel Controller:

Figure : Use of Shunt controller in solar home system

In this system, charge controller is in parallel with the battery and load. When the battery is
fully charged, then the solar panel is short circuited by the controller.
In this system, a Blocking diode is needed. So that reverse current would not flow from
battery to the panel. When the battery is charged through this blocking diode, it gets hot.
Disadvantages of shunt controller:

Lose of electricity

When the panel is short circuited, huge amount of short circuit current (Isc) flows
through the switch (FET).

Shunt controller gets hotter compared to series controller.

There is a chance of hot spot on the panel.

33

5.2.3.2 Series Controller:

Figure: Use of Shunt controller in solar home system

In this system, charge controller is connected in between with the solar panel and battery. In
order to terminate the flow of electricity to the battery, the series controller must be removed
from the battery. Theres no need of blocking diode in this system, but in many reasons it is
used to terminate the process of discharging at night. The resistance should be maintained as
low as possible in order to minimize lose of the electricity.

Advantages of series controller:

Blocking diode is not required.

Series controller switch is handled with low voltage compared to shunt controller.

Low switching noise.

It is possible of precision charge and PWM of the battery.

No chance of hot spot like the shunt controller.

34

5.2.4 Panel charging and characteristics of controller:

Figure : Relation between different types of charge controller and battery voltage and
current

Above figure shows how different kinds of charge controller controls the voltage and current.
The upper curve shows the battery voltage and the lower curve shows panel current. a,b,c,d
indicates controllers action.

35

5.2.5 Charge Controller Operation:

Fixed Set Point:

To terminate the panel current when it reaches to the maximum voltage level and then
continue it again when it reaches to the minimum voltage level is called Set point.
The relation between charging-discharging of a battery and voltage is shown in the figure
bellow-

Figure : Set point of controller (Micro-controller based)

Theres a possibility of the damage of the battery (50-100%) if the voltage level is set as the
red dotted line of the above figure.
We can match the controllers voltage-current with the state of charge (SOC) by using microcontroller and Fuzz logic. This will reduce the probability of damaging the battery(10-20%).

36

5.2.6 Selection of charge controller:

Solid state series controller is suitable for small system (4 ampere). Solid state shunt
controller is suitable for the system of 4 to 30 ampere.
A good controller must have following features

Low voltage disconnection.

Battery charging current indicator (LED or meter).

Battery voltage indicator (LED or meter).

Sense lead. Adjustable set point.

Ability of Communication (for large system).

Data logger

Computer interface

5.2.7 Voltage setting of controller:

The following factors are responsible for the voltage setting of controller

Types of battery

Charging characteristics of charge controller

Size of the battery

Maximum panel current

Depth of last charge

Figure : A solid state series controller and its various parts

37

5.2.8 MPPT Charge controller:

MPPT charge controller is a maximum power point tracker which is an electronic DC to DC

converter which takes the DC input from the solar panels, changes it to high frequency AC
and converts it back to a different DC current to match with the batteries. This is a solely
electronic tracking system and not concerned with the panel system at all.

Figure : Phocos MPPT 100/20(20amp)

5.3 Battery:
5.3.1 Battery Storage:
Batteries are often used in PV systems for the purpose of storing energy produced by the PV
array during the day, and to supply it to electrical loads as needed (during the night and
periods of cloudy weather).
Other reasons batteries are used in PV systems are to operate the PV array near its maximum
power point, to power electrical loads at stable voltages, and to supply surge currents to
electrical loads and inverters.
In most cases, a battery charge controller is used in these systems to protect the battery from
overcharge and over discharge.

38

Figure :

12 volt, 100 Ah solar battery

2 volt, 200 Ah

Industrial

battery

Figure : Battery

5.4 Inverter:
An inverter is

an

electrical

device

that

converts direct

current (DC)

to alternating

current(AC); the resulting AC can be at any required voltage and frequency with the use of
appropriate transformers, switching, and control circuits.
Inverters are commonly used to supply AC power from DC sources such as solar panels or
batteries. The electrical inverter is a high-power electronic oscillator. It is so named because
39

early mechanical AC to DC converters was made to work in reverse, and thus was "inverted",
to convert DC to AC.

5.4.1 Applications:
An inverter converts the DC electricity from sources such as batteries, solar panels, or
fuel cells to AC electricity. The electricity can be at any required voltage; in particular
it can operate AC equipment designed for mains operation, or rectified to produce DC
at any desired voltage. Designed to provide 115 VAC from the 12 VDC source provided in
an automobile. The unit shown provides up to 1.2 Amps of alternating current, or just enough
to power two sixty watt light bulbs

Figure : Inverter

5.4.6 String inverter:

Figure : String inverter

Good look
Available in small- and medium-sized PV power station
User-friendly Interface
Power level 1.5KW to 6KW.
40

5.4.7 Power plant inverter:

Professional design for large-sized PV power station
Transformer type and transformer less type
Satisfy different requirement, predigest design of power station

Figure Power plant inverter

5.4.8 Grid tie inverter:

A grid-tie inverter or a (GTI) is a special type of Inverter (electrical) that is used in a
renewable energy power system to convert direct current into alternating current and feed it
into the utility grid. The technical name for a grid-tie inverter is "grid- interactive inverter".
They may also be called synchronous inverters. Grid-interactive inverters typically cannot be
used in standalone applications where utility power is not available.

Figure : Inverter for grid connected PV

41

Chapter 6
Solar System Design
6.1 Solar home system design:
Basic Components:
1.Module
2.Battery
3.Charge Controller
4.Load

Figure : A typical solar home system design

42

6.1.1 Flow chart of solar home system design process:

The process

of

solar home system design is shown in the above flow chart. The process is started with the
site screening. It means that it must be located in a place where there is enough sunlight.
Then first stage is load estimation and after that battery sizing. Then other components of the
system such as charge controller unit and voltage converter (if needed) are selected. In this
way, the whole system design is processed. But one thing must be remembered that
Infrastructure Development Company Limited (IDCOL) has published some standard for
solar system design in Bangladesh. A designer must have knowledge about that.

43

6.1.2 Site screening:

In this part of the design, we will first analysis the location of the installation of the solar
system where there is available sunshine. As we know sunshine isnt equal in all places so
this part very important. Because the price of the whole system depends on it.

6.1.3 Load determination:

To find out the daily average load, we need some calculation. For example, a family consists
of five persons using TV for 2 hours, three Fluorescent lamps for 5 hours, Video cassette
player for 1.5 hours daily.
So power requirement of various types of loads are given bellow:
Item /loads

Rated power

TV

25W

Fluorescent lamp

15W

Radio

12W

Video cassette player

12W

Solution: The daily energy needed for the given family =2*40+2*12+3*5*15+1.5*12=347W
h

6.1.4 Battery sizing:

The following characteristics are needed for a solar home system battery:
1. For deep cycle, long lifetime
2. Low maintenance
3. High charging capacity
4. The ability of completely discharge
5. Low internal discharging rate
6. Reliability
7. Minimum change under excessive temperature

6.1.5 Array sizing:

Array sizing of a PV system means the calculation of the number of PV modules.

6.1.6 Selection of charge controller:

Functional parameter of solar home system charge controller
1. Maximum current receive from PV panel
2. Ability of maximum power supply on the load
44

3. Mark it low voltage level

4. Mark it high voltage level
5. Electric protection from thunder
6. Good regulation
7. Protection from reverse polarity
8. Adjust with system voltage

6.1.7 Selection of converter:

A solar home system use for appliance needs ac and dc voltage. As Solar module output
voltage is dc, so this system dc-dc converter or dc-ac converter needed. Some of the load is
connected necessary converter.

6.1.8 System wiring:

From PV module up to system component electric wiring is needed. Voltage drop occurs in
internal resistance of the wire. Solar home system this voltage drop should keep under a
limit.Wire cost is very important and wire length must be small size. Connection the solar
component under dement must be fulfill:
System must be safe
These wire are not make defect for system components performance
Each components works according their maximum performance
If possible use centralized 12volt dc system
If possible use centralized 24volt dc system

Wire Standard Size :

Cross sectional
area(mm)
1.0

Wire Gauge(AWG or
SWG)
18

Current Rating (A)

1.5
2.5
4.0

16
14
12

15
20
30

6.0
10.0
16.0
25.0

10
8
6
4

35
50
70
90

10

45

Maximum length of wire for 0.6 volt drop in 12 volt system:

Cable
Maximum cable Length (m) for various load Requirement
size(mm)
Load
power(w)
Current at
12 v (A)

24

36

48

60

72

96

120

10

1.5

12

2.5
4.0
6.0

20
31
46

13
21
31

10
16
23

8
13
19

7
11
16

6
8
12

5
7
10

10

76

51

38

31

26

20

16

Maximum length of wire for 1.2 volt drop in 12 volt system:

Cable
Maximum cable Length (m) for various load Requirement
size(mm)
Load
48
72
96
120 144 192
power(w)
Current at 2
3
4
5
6
8
12 v (A)
1.5
23
16
12
10
8
7
2.5
38
26
20
16
13
10
4.0
61
41
31
25
21
16
6.0
91
61
46
37
31
23
10
151
101
76
61
51
38

240
10
5
8
13
19
31

6.1.9 A small size 12 volt home system Design:

Let, according to under table for 90Wh/day design a 12 volt solar home system. Here 40Wp
module (Isc = 2.54a, Imp = 2.31A & nominal voltage = 12) and 12volt, 55 Ah battery (DOD
= 60%, Efficiency = 80%) will use. Here must remain low cost battery &module will used.
Load

Device

type(230 AC watts(w)

Daily use

No. of unit

Total watts

(hours)

hours per

load)
Fluorescent

Total watt-

day
7.5

22.5

67.5

15

1.5

15

22.5

37.5

90

lamp
TV 14
Total

IEE & NSE standard solar home system cabal voltage drop maximum 5%
46

So, maximum power loss 5%

And inverter efficiency 90%
Battery sizing:90
DC Wh/day = --------------- =105.26
0.9*0.95
105.26
Daily load Ah = --------- =8.77 Ah
12v
Battery efficiency = 80%
DOD = 60%
If autonomy of battery 3 day
8.77*3
So Amp-hour for battery = ---------- = 54.8 Ah
0.6*.08
As battery voltage is 12 volt and system volage is 12 volt, and output of battery is 55
Ah then here one battery is needed.
Array sizing:
Daily PV module output = 12*2.31*4.2
= 116.42 Ah
Daily avg. pick insulation = 4.2 hours
Summarizing 20% loss PV array sizing
So this system requirement DC watt-hours = 105.26 Wh/day
105.26
So no. of module =--------------- = 1
116.42*.8
Charge controller size
Given Isc = 2.54A
Charge controller design current = 1.25*2.54A = 3.175A
37.5
Maximum DC current =---------- =3.47A
12*0.9
Here needed charge controller rating = 3.5A
Wire size:
Design current = 3.17A
Maximum load current = 3.47A
47

Current from PV module to charge controller = 3.175*1.25 = 4.0A

So, wire size 1.0mm

6.1.10 a big size 24 volt home system Design:

Let, according to under table for 2090Wh/day design a 24 volt solar home system.
Here 50Wp module (Isc = 3.22A, Imp = 2.94A & nominal voltage = 12) and 2volt,
660 Ah battery (DOD = 60%, Efficiency = 80%) will use. Here must remain low cost
battery &module will used.
Load

Device

Daily use

type(230

watts(w)

(hours)

No. of unit

Total watts

Total watthours per

AC load)

day

CFL

11

66

330

TV 14

60

60

180

Computer

400

400

800

Mobile

16

64

60

120

720

662

2090

color

charger
Fan
Total

IEE & NSE standard solar home system cabal voltage drop maximum 5%
So, maximum power loss 5%
And inverter efficiency 90%
All appliance input voltage = 230volt

Battery size
2090
DC Wh/day = --------------- =2444Wh
0.9*0.95
2444Wh
Daily load Ah = --------- =102Ah
48

24v
Battery efficiency = 80%
DOD = 60%
If autonomy of battery 3 day
102*3
So Amp-hour for battery = ---------- = 638Ah
0.6*0.8
As battery voltage is 2 volt and system voltage is 24 volt,
So 12 battery are needed
Output of battery is 660 Ah
Battery requirement 638Ah

Array sizing
Daily PV module output = 12*2.94*4.2
= 148.2 Ah
Module nominal voltage = 12V
Daily avg. pick insulation = 4.2 hours
Summarizing 20% loss PV array sizing
So this system requirement DC watt-hours = 2444Wh/day
2444
So no. of module =--------------- = 21
148.2*0.8
For getting 24V, 2 no of module connect in series and like this 11 no of set connect in
parallel are needed
Charge controller
Given Isc = 3.22A
Total short circuit current = 11*3.22A = 35.42A
Charge controller design current = 1.25*35.42A = 44.275A
662
Maximum DC current =---------- =31A
12*0.9
Here needed charge controller rating = 45A
Inverter size
Size of the inverter = 662/(.9) *1.25= 920W
So 1.0KW inverter is needed
49

Wire size
Design current (PV array to charge controller)= 44.275A

Maximum load current (charge controller to inverter) = 33A

Current from PV module to charge controller = 44.275*1.25 = 55.34A
So, wire size 16mm

6.1.11 Design of 50 watt solar PV system:

Array sizing:
If energy demand is 50W, Rate of insulation is 4.2 KW/m and efficiency is 0.7 then,
The size of module = 50/(4.2* 0.7 )=17W
But 17W module is not available. So we need 50Wp PV module.
No of PV module:
If, per day energy output is Pdm, module output voltage is Vmm and current is ILm then,
Per day energy output is,
Pdm=ILm*D*Vmm
No of module
Nm=PAR/Pdm
Where,
Nm= No of module
PAR= Per day energy requirement
Battery sizing:
If the system voltage 12V, Battery depth of discharges 70% and autonomy 3 days then
we need, we know,
P=VI
If energy demand is 50WH, then,
For, 12 volts battery, we need power= 50WH/ 12V = 4.16Ah
Autonomy of 3 days, So 4.16*3 = 12.48 Ah
But, depth of discharge is 75%
So, power = 12.48Ah/(0.75*0.8) = 20.8Ah[If efficiency is 80%]
So, we need to battery those absorbed of capacity is 21 Ah
So, we need = 21 /100 = 0.21 = 1 battery
Standard size of wire:
For the wire selection we need to concentrate below the characteristic:
50

Length of wire
Wire receptivity
Cross sectional area of wire
Flow of electricity of wire
If, L = length
I = Amperes,
= Receptivity,
a = Area of wire,
Then,
Voltage drop, Vd = 2LI /a
Where,
= 0.0183 /m /mm

6.1.12 Design of 60 watt solar PV system:

Array sizing:
If energy demand is 60W, Rate of insulation is 4.2 KW/m and efficiency is 0.7 then,
The size of module = 60/(4.2* 0.7 )=20.40W
But 21W module is not available. So we need 50Wp PV module.
No of PV module:
If, per day energy output is Pdm, module output voltage is Vmm and current is ILm then,
Per day energy output is,
Pdm=ILm*D*Vmm
No of module
Nm=PAR/Pdm
Where,
Nm= No of module
PAR= Per day energy requirement
Battery sizing:
If the system voltage 12V, Battery depth of discharges 70% and autonomy 3 days then
we need, we know,
P=VI
If energy demand is 60WH, then,
For, 12 volts battery, we need power= 60WH/ 12V = 5 Ah
Autonomy of 3 days, so 5* 3 = 15 Ah
But, depth of discharge is 75%
So, power = 15 Ah / (0.75*0.8) = 25 Ah [If efficiency is 80%]
51

So, we need to battery those absorbed of capacity is 25 Ah

So, we need = 25 /100 = 0.25 = 1 battery
Standard size of wire:
For the wire selection we need to concentrate below the characteristic:
Length of wire
Wire receptivity
Cross sectional area of wire
Flow of electricity of wire
If, L = length
I = Amperes,
= Receptivity,
a = Area of wire,
Then,
Voltage drop , Vd = 2LI /a
Where,
= 0.0183 /m /mm

6.1.13 Design of 110 watt solar PV system:

Array sizing:
If energy demand is 110W, Rate of insulation is 4.2 KW/m and efficiency is 0.7 then,
The size of module = 110/ (4.2* 0.7) =37.41W
But 38W module is not available. So we need 50Wp PV module.
No of PV module:
If, per day energy output is Pdm, module output voltage is Vmm and current is ILm then,
Per day energy output is,
Pdm=ILm*D*Vmm
No of module
Nm=PAR/Pdm
Where,
Nm= No of module
PAR= per day energy requirement
Battery sizing:
If the system voltage 12V, Battery depth of discharges 70% and autonomy 3 days then
we need, we know,
P=VI

52

Chapter 7
10 watt solar power system
The sun is a renewable energy source thats free and plentiful. Some people power their
entire home with solar energy. A few even sell back the energy to the electricity grid for a
profit. Our society can't continue to work on oil, and with rising gas prices and more frequent
power outages, solar energy seems to be the way to go.
The objective of this project is to build a small solar power system as a supplementary for
home power needs and with the goal of keeping major home appliances and necessary
gadgets active without the concern of weather and grid status. Here, its explained below the
detail procedure to build a 10-watt solar power system.

7.1 MATERIALS
1. 10 -watt solar panel
2. Charge controller(3-10A)
3. Inverter (20 watt)
4. Battery (7Ah)
5. MK box(plastic)
6. Multi socket
7. 7 watt energy light
8. Light holder
9. Wooden Box()
10. Screw 5,3,
11. Royal screw
12. Washer +nuts
13. 1.5 Rm wire
14. Scotch tape
15. Flexible cable

1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
10 piece
10 piece
15-20 piece
1 meter
1 piece
2 meter

7.2 TOOLS
1. Hand Drill with full box
2. Wire cutters
3. Pliers
4. Screw Driver
5. AVO meter

54

7.3 Dimensional Information

7.4 Connection Diagram

55

7.5 Specifications

TYPE

10W Solar Panel

RATED MAXIMUM POWER

(Pmax)

RATED MAXIMUM POWER (Pmax)

TOLERANCE

3%

VOLTAGE @ Pmax (Vmp)

17.6V

CURRENT @ Pmax (Imp)

0.57A

SHORT CIRCUIT CURRENT

(Isc)

0.61A

OPEN CIRCUIT VOLTAGE (Voc)

21.6V

NOMINAL OPERATING CELL

TEMPERATURE

47C 2C

CELL TYPE

Mono

WIND LOADING

50lbs/sq. ft.

PANEL DIMENSIONS

H 11.5 x W 13.5 x D 1 (290mm x

340mm x 25mm)
PANEL ASSEMBLY

PANEL ASSEMBLY WEIGHT

7.5 lbs. (3.2 kg)

STANDARD TEST CONDITIONS

AM -1.5 STC=1000W/m2 TC=25C

SOLAR ARRAY

VOLTAGE

12VDC

\
CAPACITY

7Ah

BATTERY
BATTERY TYPE

Deep Cycle, Sealed Gel, Lead acid

HOUSING (ea.)

Polypropylene UL 94-V0/File E50955

56

7.6 Work Procedure

At first design the project layout with Microsoft visio.Then a wooden box cabinet has to be
build as required in the design. Setup the solar pannel in top of the cabinet with an angle of
45 degree. Inside the cabinet a frame has to be created for the battery. Plan the installation of
the battery pack and solar panel array prior to installation. For best results, mount the battery
pack in a cabinet as close to the panels as practicable. Mount the cabinet, then install and
connect the batteries prior to connecting the solar panels as referred in the wiring diagram.
Charge controller has been setup in front of the cabinet to view the present status. For DC to
AC conversion and to achieve AC output, setup Inverter inside the cabinet. Then connect to
the inverter with battery. A 1.5 RM cable has to be connected between solar panel and
Charge controller.

7.7 Connection Diagram

Solar panel (10watt)

Charge
Controller

Inverter

AC out
Max 20 watt

Battery
7AH

Fig: 10 watt solar power system

57

7.8 Load calculation

Maximum 20 watt
Load
type(230 AC
load)
Fluorescent
lamp
Mobile charger
Total

Device
watts(w)

Daily use
(hours)

No. of unit

Total watts

Total watthours per

day
21

12

12
45

24
45

58

Real Picture of Project

Figure: Solar Panel

Figure: Side View

59

Figure: Charge Controller

Figure: Internal View

60

Conclusions
Solar energy technologies generate electricity without producing air or water
pollution. Solar thermal energy technologies may require cooling water, but
most of this water can be recycled. Only small amounts of hazardous
materials are produced in the manufacture of photovoltaic cells and CSP
equipment and essentially none in other solar thermal applications. According
to the U.S. Environmental Protection Agency (EPA), CSP plants do not
damage the land, but merely take it out of use for other applications such as
agriculture. Wildlife habitat may be displaced from land used for such
systems, however.104
Solar electricity can reduce carbon emissions by offsetting the need for
carbon-producing fuels. For example, Applied Materials has installed solar
panels at its manufacturing plant in Austin that will generate about
33.7 MWh annually and eliminate about 54,000 pounds of carbon emissions
each year.105
Solar PV represents a true zero carbon emission generation option.Solar PV
technology offers significantly lower capital and operating costs than Diesel
power technologyHigher solar radiation levels such as at Blochistan would
lower electricity cost.The nature solar energy source makes it more preferred,
practical energy solution.

62

REFERENCES

[1]Solar power system Web. 18 sept. 2013

<http://en.wikipedia.org/wiki/Solar_power.>
[2] "Cost of Solar Panels." Solar Panels. Web. 12 sept. 2013.
<http://www.solarpanelinfo.com/solar-panels/solar-panel-cost.php>.
[3] "Photovoltaic Module - Wikipedia, the Free Encyclopedia." Main Page Wikipedia, the Free Encyclopedia. Web. 13 sept. 2013.
<http://en.wikipedia.org/wiki/Photovoltaic_module>.
[4] National Renewable Energy Laboratory (NREL) Home Page. Web. 02 sept.
2013. <http://www.nrel.gov/>.
[5] Project Free Power. Web. 25sept. 2013.
<http://www.projectfreepower.com/solarpower.html>.
[6]How do Photovoltaics Work." WCubed Commercial Services. 02 Feb. 2009
<http://www.wcubed.com/solar/How%20do%20Photovoltaics%20Work/art.jpg>.
[7]Locke, Susannah. "How does solar power work?: Scientific American." Science
News, Articles and Information | Scientific American. 20 Oct. 2008. Scientific
American. 02 Feb. 2009 <http://www.sciam.com/article.cfm?id=how-does-solarpower-work>.
[8]"Solar Energy Technologies Program: Concentrating Solar Power." EERE:
EERE Server Maintenance. 15 Sept. 2005. U.S department of Energy. 02 Feb.
2009 <http://www1.eere.energy.gov/solar/csp.html>.
[9]Solar Thermal Collector." GlobalForceInfo.com. 02 Feb. 2009
<http://www.globalforceinfo.com/wp-content/uploads/2008/08/solar-thermalcollector.jpg>.
[10]Sun
Energy.
02
Feb.
2009
<http://sunenergyfacts.com/wpcontent/uploads/2008/02/solar-energy-storage.jpg>.

63