277.
1
275.7
1/32"
10 27/32"
2 1/8"
13/32"
Notch Out Cross Brace To Receive
Bracket. Grain Of Bracket Should Run
Vertically - 90 Degrees To Brace Grain.
Notch Out Cross Brace To Receive
Bracket. Grain Of Bracket Should Run
Vertically - 90 Degrees To Brace Grain.
169.2
9 3/32"
6 21/32"
226.4
2.4
3/32"
8 29/32"
3/32"
3.0
2.4
54.3
122.5
54.5
2 1/8"
4 13/16"
2 5/32"
5/8"
1/8"
231.3
15.5
27/32"
54.3
6 5/8"
21.7
168.5
3/32"
7/16"
54.3
2 1/8"
R 10.5
11.5
1 5/32"
3/16"
29.2
4 23/32"
4.5
120.0
1 5/32"
0"
2.2
6.0
10 29/32"
5/8"
9/32"
3/16"
277.1
7 1/32"
16.0
7.5
4.5
178.3
29.2
1/32"
1/4"
7 1/32"
1/4"
178.3
15/32"
169.2
R 10.5
26.5
142.7
1 1/32"
5 5/8"
3/16"
27/32"
5.0
21.7
3/32"
Notch Out Cross Brace To Receive
Bracket. Grain Of Bracket Should Run
Vertically - 90 Degrees To Brace Grain.
2.3
5/8"
16.0
15/16"
23.9
6 21/32"
0"
13/32"
0"
Make 2 "D" Fan Braces. Make Them
Opposite Hand From Each Other Because
They Are Mirrored On The Top Plate
15.5
5/8"
2.0
243.4
3/32"
9 19/32"
1/8"
3.0
251.7
26.5
198.8
26.5
1 1/32"
7 13/16"
1 1/32"
3/16"
5.0
9 29/32"
210.1
7 3/4"
8 9/32"
3.0
1/8"
197.1
1/8"
3.0
23.4
8 9/32"
26.5
157.1
26.5
1 1/32"
1 1/32"
6 3/16"
1 1/32"
Make 2 "F" Fan Braces. Make Them Opposite
Hand From Each Other Because They Are
Mirrored On The Top Plate
3/16"
26.5
5 11/16"
5.0
144.2
1 1/32"
Make 2 "G" Fan Braces. Make Them
Opposite Hand From Each Other Because
They Are Mirrored On The Top Plate
7 9/16"
210.1
7 3/4"
192.3
197.1
26.5
3/16"
5.0
29/32"
224.7
0"
8 27/32"
Note: You Should Make All Your Bracing Longer Than It
Needs To Be, Or As Shown In The Bracing Diagrams Above.
Leave Each Brace At Least 3/8" Long And Trim Back During
Fitting Of The Back And Top Plates To The Guitar Sites.
224.7
3/16"
8 27/32"
5.0
12.0
6.0
10 29/32"
26.5
171.7
26.5
1 1/32"
6 3/4"
1 1/32"
Make 2 "H" Fan Braces. Make Them
Opposite Hand From Each Other Because
They Are Mirrored On The Top Plate
Top Plate Brace Layouts
Note For Detailed Construction Instructions
Refer To Our Book "Guitar & Ukulele Construction
Handbook @ http://shopglss.com
This Drawing or Drawings Are To Used For One Use Only
And Not Reproduced For Any Other Purpose Than
Construction Of This Particular Instrument, and a One Time
Reproduction Only is Allowed
Reproduction, Distribution or Sales For Any Other Use Is
Strictly Prohibited And Falls Under U.S Copyright Laws For
David VerBurg AIA c 2013
This Sheet Size Is Metric A0 Size Overall Size is 1189mm x
841mm With 15mm Borders On All Sides. For USA
Customers Print On Architectural "E" (36" x 48") Without
Resizing For 1:1 Printout.
Georgia Luthier Supply
Classical Guitar Plan #3
Date: Feb. 2010
Revisions: Dec 13, 2013
Unless Noted Otherwise,
These Plans Are Drawing
Full Scale. They Are
Labeled in mm and
Fractional Inches
Sheet Number
C3
