CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 2

Solar Shading Louver Systems

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 3

Introduction

Mestek has a strategic alliance and

exclusive licence agreement with Colt
Group USA. Mestek is the exclusive
licensee to produce and market the Colt
designed products for the US market and
all products are produced in the USA.
Additionally, Mesteks Architectural
activities include Linel and AWV. The
emphasis for these companies is in
providing products and solutions that
beautify and improve the performance of
buildings through Intelligent Envelopes.

The movement toward sustainable building

designs is being driven largely by
environmentally-sensitive building owners
and/or their prospective tenants. As these
owners and their consultants weigh their
design objectives and alternatives, they
often find that exterior solar shading
systems are an ideal part of the "green"
solution for their buildings.
An exterior solar shading system blocks a
significant amount of the solar radiation
from entering the buildings windows which results in reduced HVAC installed
costs due to equipment down-sizing and
reduces operating costs due to reduced
cooling loads.
Indeed, some form of exterior solar
shading is now part of the prescriptive
design requirements in the new Standard
for the Design of High Performance,
Green Buildings, except for Low-rise
Residential Buildings (ANSI, ASHRAEs,
USGBC, IES 189.1).

SHADING LOUVERS

COLTS OFFERING

Solar shading louver systems are one of

the most effective ways to reduce air
conditioning loads, while offering designers
the opportunity for distinctive architectural
impact.

n Computer modeling of the solar shading

louver system including calculation of sun
angles and reduction in solar heat gains
by exposure throughout the year.

Radiation from the sun is transmitted,

absorbed and reflected by the louvers. As
a result solar heat gain is prevented from
passing into the building. If an operable
system is chosen, the adjustable louvers
will track the position of the sun
increasing the systems shading
effectiveness and further reducing glare.
On overcast days, the operable louvers can
be opened to maximize the natural
daylight into the building.

n All Colt solar shading louver systems

are custom designed for your
application and can be provided in
various configurations, materials,
finishes and coatings to meet each projects
requirements.
n Two control options are available for
the operable systems SolTronic III for
most projects and the ICS 4-link for
very large projects with additional
functionality.
n All systems are durable with low
maintenance needs.

COLTS TRACK RECORD & CAPABILITIES

Colt has more than 40 years experience in
the design and supply of solar shading
louver systems. Colt was the first to
incorporate electricity generating
photovoltaic cells into solar shading
systems. Colt continues to build on this
experience and has been providing solar
shading systems for the US market since
2006.
We offer an extraordinary range of solar
shading systems from fixed to fully
operable with a variety of carrier systems,
materials and finishes.
Colt is dedicated to innovation and has
comprehensive design capabilities. While
this brochure provides a general overview
of our capabilities, we welcome the
opportunity to develop solutions to satisfy
your unique requirements.

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 4

Solar Altitude for

21st June

SOLAR GEOMETRY
The sun rises in the East and sets in the
West. The sun travels in an arc, reaching
its highest altitude in the summer and its
lowest altitude in the winter.
NORTH FACING FAADES

Solar Altitude for

21st Sept
West
NW

SW

Solar Altitude for

21st Dec

South

North

For predominately north facing faades in

all but the lowest latitudes the faade will
not receive direct sunlight and solar
shading is not required or beneficial from
an energy perspective.

SE

NE
East

Shading louvers may be used for an

asthetic look complimentary with the other
south, east and west facing faades.

12 pm (1 pm)

Summer

11 am (2 pm)
10 am (3 pm)
9 am (4 pm)
8 am (5 pm)

12 pm (1 pm)

Winter

9 am (4 pm)
8 am (5 pm)

Vertical shadow angle (the

projected angle
of the solar altitude)
South facing
(Northern Hemisphere)

While passive solar heating at times is

beneficial, some might be surprised to
learn that the cooling loads on many
southern-facing zones peak in the
late fall/early winter due to the solar
radiation.

Effective solar shading on the South, East

and West faades can be achieved only by
using an operable shading louver system
on the buildings faade. The angle of the
louvers is adjusted throughout the day to
provide optimal shading.

Spring/Autumn

11 am (2 pm)
10 am (3 pm)

For a predominately South facing faade,

a small amount of solar shading can be
achieved using a fixed horizontal brise
soleil sunshade. In winter such a device,
however, cannot stop direct rays from the
sun penetrating the buildings windows
since the sun is much lower.

With a predominately East or West facing

faade, a fixed system will not perform
well throughout the day as the altitude of
the sun varies throughout the day.

12 pm (1 pm)
11 am (2 pm)
10 am (3 pm)
9 am (4 pm)
8 am (5 pm)

SOUTH, EAST AND WEST

FACING FAADES

Too much shading

Optimum shading

Too much glare,

light passes
through the
louver blades

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 5

Louver Materials
& Finishes

SHADOGLASS
Shadoglass are fixed or operable exterior
solar shading systems that incorporate
glass louvers. The louvers can be installed
either horizontally or vertically on the
buildings faade. A Shadoglass shading
system can significantly reduce solar heat
gain while providing unobstructed views
and natural daylight. With todays glass
technology, very effective shading
performance can be achieved with glass
louvers.
Glass louvers are available in various
colors, surface finishes, patterns and
coatings to meet specific design
requirements. This enables the designer to
control the quality of light entering the
building.
Features and benefits
n Available in widths up to a nominal 24".
n Available in unsupported spans up to a
nominal 6.5', supported spans up to a
nominal 13' (depending on wind loads
and other design criteria).
n Wide range of colors, surface finishes,
patterns and coatings (i.e. fritted).
n All principal support components are
manufactured from corrosion-resistant
extruded aluminum alloy with stainless
steel fixings.
n Fully operable or fixed.

Colt offers a variety of materials and finishes for the shading louvers
n Shadoglass Glass with various colors, surface finishes, patterns and coatings
n Shadovoltaic Glass with photovoltaic cells
n Shadoprism Non-specular prisms
n Shadotex Textile fabrics
n Shadometal Metal - solid or perforated
n Shadotimber Timber wood

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 6

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 7

Louver Materials
& Finishes

SHADOVOLTAIC
Shadovoltaic are fixed or operable exterior
solar shading systems that incorporate glass
louvers with photovoltaic cells integrated
into the glass to generate electricity at the
same time as providing shading. The
louvers can be installed either horizontally
or vertically on the buildings faade.
Both monocrystalline and polycrystalline
cells are available. The photovoltaic cells
may be integrated into the glass, either by
attaching them on the underside of the
glass louver or by laminating them between
two layers of glass. The glass panels are
heat soak tested toughened glass with the
edges treated to remove stress. Glass
thicknesses of between a nominal 0.3" and
0.6" are available. The glass specification
can be tailored to suit each application.
Photovoltaic glass louvers are available in
various colors, surface finishes, patterns and
coatings to meet specific design requirements.
Features and benefits
n Combines the functions of solar shading
with the generation of electrical power.
n Available in widths up to a nominal 24".
n Available in supported spans up to a
nominal 13' (depending on wind loads
and other design criteria).
n All principal support components are
manufactured from corrosion-resistant
extruded aluminum alloy with stainless
steel fixings.
n Fully operable or fixed. An operable
BIPV system which tracks the suns
position typically generates about 20%
more electricity than a fixed system.

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 8

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 9

Louver Materials
& Finishes

SHADOPRISM
Shadoprism are operable exterior solar
shading systems that incorporate nonspecular prismatic plates.
The system is a transparent sun protection
system for faades and glass roofs that
prevents the ingress of the direct sun's heat
into the interior of the building and at the
same time lets through a maximum of
diffuse daylight.
Total reflection of the daylight occurs
where the prism angle is 90 relative to the
daylight. This total reflection functions
only within a very narrow range of angle.
As such, the operating prismatic louvers
will track the sun's position reflecting
the maximum amount of direct sunlight
while allowing in all the diffuse light.

On overcast days, the prism louvers can be

opened to allow unhindered vision and
maximum natural daylight through the
glazing.
Features and benefits
n Highly effective shading performance
with maximizing natural diffuse daylight
into the building.
n Available in widths up to a nominal 24".
n Available in unsupported spans up to a
nominal 6.5', supported spans up to a
nominal 13' (depending on wind loads
and other design criteria).
n All principal support components are
manufactured from corrosion-resistant
extruded aluminum alloy with stainless
steel fixings.
n Normally operable.
8

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 10

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 11

Louver Materials
& Finishes

SHADOTEX
Shadotex are fixed or operable exterior
solar shading louver systems that
incorporate a unique, alternate solar
shading solution. It consists of a special
fabric stretched between two sides of a
louver support frame. The fabric is
manufactured with a weave to prevent
solar glare and solar heat gain. The fabric
can also create attractive diffused light
and allow a degree of vision. The louvers
can be installed either horizontally or
vertically on the buildings faade.
This type of system is extremely light
weight which allows for very large spans
without the need for additional
supporting framework.
Features and benefits
n A wide variety of fabric and color
choices including PVC-coated polyester,
Teflon glass fiber, silicon glass fiber
and ETFE (colored, translucent or
screen printed).
n High solar absorption and high solar
reflection.
n Light weight construction ideal for
large spans.
n Good external visibility.
n Easy to clean as the fabric is typically
resin/Teflon coated.
n All principal support components are
manufactured from corrosion-resistant
extruded aluminum alloy with stainless
steel fixings.
n Fully operable or fixed.

10

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 12

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 13

Louver Materials
& Finishes

SHADOMETAL
Shadometal are fixed or operable exterior
solar shading systems that may be installed
vertically or horizontally onto the buildings
faade or roof, and incorporate metal louvers.
Perforated, solid, curved louvers and other
configurations are available. The perforated
louvers can also create attractive diffused
light and allow a degree of vision.
Features and benefits
n Available as standard in widths up to a
nominal 16" in one piece construction
and up to 41" in multiple (clipped
together) construction.
n Available in unsupported spans up to a
nominal 33' (depending on wind loads
and other design criteria).
n Solid or perforated for improved visibility.
n Wide range of over 20 standard louver
profiles.
n All principal support components are
manufactured from corrosion-resistant
extruded aluminum alloy with stainless
steel fixings.
n Fully operable or fixed.

12

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 14

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 15

Louver Materials
& Finishes

SHADOTIMBER
Shadotimber are fixed or operable exterior
solar shading louver systems that
incorporate a unique, alternate solar
shading solution. It consists of timber
wood louvers, usually western red cedar
which, if left untreated, ages to a silverygrey tone. The louvers can be installed
either horizontally or vertically on the
buildings faade.
Alternatively, a simulated wood
appearance can be provided on
shadometal louvers through a dyesublimation process which will remain
colorfast at the original appearance.
This type of system is generally intended
for shorter spans without the need for
additional supporting framework.
Features and benefits
n Although normally western red cedar,
other types of timber wood can be
provided.
n Ideal for shorter spans and thinner louvers.
n All principal support components are
manufactured from corrosion-resistant
extruded aluminum alloy with stainless
steel fixings.
n Fully operable or fixed.

14

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 16

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 17

Carrier Systems

Colt offers a variety of carrier systems for the solar shading systems
n System 1 Center pivot supported at various points along the length by a torsion tube
n System 2 Center pivot point-supported at the ends
n System 3 Center pivot continuously supported over the entire length by a torsion tube
n System 4 Back pivot point-supported at the ends
n System 5 Center pivot continuously supported at the ends

CARRIER SYSTEM 1
Intended for wider spans, carrier system 1
incorporates a central aluminum torsion
tube along the entire length of the louver,
and is ideal for continuous facades, as well
as for roofs.
For glass louvers, cross sectional widths
from a nominal 12" to 24" are available.
This carrier system is also suitable for use
with a variety of louver materials
including glass, metal, fabric, timber
wood, terracotta clay and translucent
acrylic.
C

8.66"

55

Glass Parameters Table

Dimensions

LS1 - 55

LS1 - 65A

LS1 - 65B

A (max)

98.42"

129.92"

129.92"

11.81" - 19.68"

13.78" - 21.65"

16.54" - 23.62"

2.36"

2.36"

2.36"

0.39"

11.81"

65A
13.86"

65B

Angle of rotation

0 - 100

Torsion tube dia.

2.17"

0.39"
o

0 - 100
2.56"

0.39"
o

0 - 100

2.56"

Note: Table to be used as a guide only. Allowable dimensions depend upon the specific
requirements of the project.

16

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 18

17

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 19

Carrier Systems

CARRIER SYSTEM 2
Primarily intended for shorter spans or
where frequent anchor support points are
available, carrier system 2 provides
minimum obstruction from the louver so
when used with glass louvers it
maximizes the natural daylight and
enhances the views to the outside.
For glass louvers, carrier system 2 is
available in cross sectional louver widths
of up to a nominal 20".
This carrier system is also suitable for use
with a variety of louver materials
including glass, metal, fabric, timber
wood, terracotta clay and translucent
acrylic.

E
A

Plan view of LS2-30 bracket

8.66"

Straight carrier bracket

Glass Parameters Table

Dimensions

LS2-30

A (max)

78.74"

19.68"

2.36"

0.39"

66.93"

Angle of rotation

0 - 100

Note: Table to be used as a guide only. Allowable dimensions

depend upon the specific requirements of the project.

18

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 20

19

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 21

Carrier Systems

CARRIER SYSTEM 3
Like carrier system 1, carrier system 3 is
intended for wider spans and incorporates
a discreet central aluminum torsion tube
along the entire length of the louver. It is
ideal for continuous facades as well as for
roofs.
For glass louvers, carrier system 3 offers
spans up to a nominal 13 feet long
without adding any additional supporting
structure and cross sectional louver widths
up to a nominal 24".
This carrier system is also suitable for use
with a variety of louver materials
including glass, metal, fabric, timber
wood, terracotta clay and translucent
acrylic.

Glass Parameters Table

Dimensions

LS3

A (max)

157.48"

23.62"

2.36"

0.20"

Angle of rotation

0 - 100

38 mm

Torsion Bar

Note: Table to be used as a guide only. Allowable dimensions depend upon the specific
requirements of the project.

20

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 22

21

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 23

Carrier Systems

CARRIER SYSTEM 4
Carrier systems 1, 2, 3 and 5 are center
pivoted systems. System 4 provides a
back hung end pivoted solution with
hidden control mechanisms integrated
within the main vertical mullion supports.
This allows for seamless continuous
louvers with unobtrusive supports when
viewed from the outside.
For glass louvers, carrier system 4 offers
smaller spans up to a nominal 6 feet long
and in cross sectional louver widths up to
a nominal 24".
This carrier system is also suitable for use
with a variety of louver materials
including glass (with our without
photovoltaic cells), metal, fabric, timber
wood, terracotta clay and translucent
acrylic.

C
D

90

45

Glass Parameters Table

Dimensions

LS4

A (max)*

70.87"

13.78" min / 23.62" max

2.56"

0.39"

Angle of rotation

0 - 85

Note: Table to be used as a guide only. Allowable dimensions depend upon the specific
requirements of the project.
* If spanning across an intermediate mullion, max 141.73".

22

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 24

23

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 25

Carrier Systems

CARRIER SYSTEM 5
Carrier system 5 is a fully centered
pivoted system which provides maximum
visibility. Louvers are supported at each
end by a bonded and extruded end cap.
For glass louvers, carrier system 5 offers
smaller spans up to a nominal 6 feet long
without any additional support work, in
cross sectional louver widths up to a
nominal 24".
This carrier system is also suitable for use
with a variety of louver materials
including glass, metal, fabric, timber
wood, terracotta clay and translucent
acrylic.

Glass Parameters Table

Dimensions

LS5

A (max)

70.87"

23.62"

1.97/2.36"

0.39"

Angle of rotation

0 - 100

Note: Table to be used as a guide only. Allowable dimensions depend upon the specific
requirements of the project.

24

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 26

25

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 27

Controls

OPERABLE VERSUS FIXED SYSTEMS

SOLTRONIC III

Operable solar shading louver

systems adjust the shading louvers
position to provide the most effective
shading. The benefits of increased
shading effectiveness and resultant
energy savings far exceed the modest
cost addition between a fixed and
fully operable system.

The Solaronic III system can control up to

15 groups of actuators (exposures) with
15 actuators per group which is enough
for the vast majority of systems.

With operable systems occupant

comfort can also be enhanced as glare
can be lessened during bright days,
while maximizing the natural daylight
entering the building when overcast.
Typically, multiple banks of louvers
are operated by linear actuators
though a system of levers and push
rods or by rotary actuators through a
system of worm gears.

26

With both control systems, the actuators

typically have a cycle time from fully
closed to fully open of about 90 seconds.
To fully calibrate/synchronize the
actuators/louvers as there are slight
differences in each actuators cycle time,
each actuator is provided with a MSG.

ICS 4 LINK
The ICS4 Link system can be
programmed with customer specific
programs. It can handle a very large
number of exposures and actuators
through the main control panel w/CPU
(and sub-panels w/CPUs). The ICS4 Link
system can be fully integrated with a
BMS and offers remote access over the
Internet, data logging and other datadriven operating flexibility/features.

At the initial commissioning, all the

actuators will be cycled and the MSG will
adjust the control of each actuator to
account for the slight differences in cycle
time to assure proper alignment of the
louver blades.
With an ICS 4 link system should a
problem with an operable system arise,
Colt can investigate the problem remotely
communicating with the control system
over the internet to trouble shoot most
problems.

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 28

CONTROL FUNCTIONALITY
Colt operable shading louver systems
employ a weather station to provide
much more functionality. The weather
station (usually one per building) is
typically installed on the roof and
includes:
n Lux sensor for brightness
n Wind speed sensor
n Water (rain/ice/snow) sensor
n Outside air temperature sensor

In addition to management of the shading

louvers positions though its sun tracking
program, Colts control systems with
weather station have many more features:
n The control systems have a relay to
interlock with the fire alarm system. If
there is a fire alarm, the louvers are
driven to a fully open (horizontal)
position.
n If the wind sensor indicates a wind
speed in excess of about 25 MPH, the
louvers will be driven to the wind safe
position (the most effective wind safe
position is 37 degrees down from
horizontal).
n If the outside air temperature
approaches 32 F per the outdoor air
temperature sensor and water is detected
by the water sensor, the louvers are
driven to the freeze protection position
(slightly less than fully closed).
This is a major advantage of operable
over fixed systems. Snow and ice can
gather on a fixed blade (even at a 45
degree angle). This snow and ice can
ultimately fall endangering the
pedestrians below. With the operable
systems freeze protection position, this
concern is greatly reduced.

Operable systems have another major

advantage over fixed systems. The
moving louver blades discourage birds
from perching and nest building as
opposed to a fixed system which does
not.
n The control systems have a maintenance
switch. If the maintenance switch is
activated the louvers are driven to a
fully open (horizontal) position for
cleaning.
n The control systems have a 24-hour
clock. If it is after dark the louvers
are driven to their nighttime position
(which could be anything from fully
open to fully closed). From a nighttime
light pollution perspective, the
nighttime position would normally be
fully closed.
n If it is an overcast day as sensed by the
lux sensor (under 15k lux), the louvers
will be driven to the fully open
(horizontal) position. (As a comparison,
a bright day might have a lux reading
of 80k lux).
n If none of the above conditions are
present, the control system will
position the louvers automatically per
the sun tracking software.

27

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 29

Installation and Maintenance

INSTALLATION

MAINTENANCE

A wide variety of mounting options

are possible including mounting the
shading louvers directly to the curtain
wall mullions or to the building
structure. The method to be used for
each project requires structural
analysis and engineering to account
for the dead weight, wind, snow and
ice loads. Please consult with us on
the most appropriate mounting
method for your specific project.

The actuators linkages and non-lubricated

bearings are free from routine
maintenance. An annual visual inspection
of the shading louvers should be
sufficient.
The actuators are tested to 10,000 cycles
in each direction (20,000 total).

n The use of a working platform lowered

between the exterior windows and
shading louvers is a common approach.
In some cases, rails or cradle runners
are integrated into the mullions and
supporting structure to guide the
working platform. In other cases,
outriggers can be provided to protect the
windows and shading louvers from the
working platform.

Should a louver or window behind the

louver need replacement, Colt typically
employs a spring-bolt mounting design
which allows for the removal of each
individual louver independently avoiding
the need to remove all the preceeding
louvers within the row.
WASHING
The washing method to be used of the
surfaces of the exterior windows and
shading louvers is normally anticipated in
the solar shading louver systems design.
A titanium dioxide coating can be
provided on the glass louvers to reduce
the maintenance effort associated with
glass cleaning.

Proper alignment of the mullions is

key to a smooth installation.
In some cases the louvers can be
factory pre-assembled or unitized to
reduce installation time.
In either case, the operating
mechanisms such as bearings, rods
and levers are typically factory
installed and aligned in the mullions.
After commisioning, a capping piece
will be installed on the mullions to
protect these mechanisms from the
elements.
COMMISSIONING
Proper commissioning by experts is
essential. We recommend that our
staff commission and certify the
system.
28

A variety of window washing approaches

can be accommodated.
n A bosuns chair can be lowered
between the exterior windows and
shading louvers.

n Catwalks can be incorporated into the

structure supporting the shading
louvers. This approach is less common
due to the expense of the additional
structural elements.

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 30

Custom Solutions

Colt is dedicated to innovation and has

comprehensive design capabilities.
While this brochure provides a general
overview of our capabilities, we
welcome the opportunity to develop
solutions to satisfy your unique
requirements. The following are a few
other custom solutions we have
provided on selected projects.
TEXTURED LOOK
Varying the ceramic frit in a random
pattern on the Shadoglass louvers can
give the building a distinctive
aesthetically pleasing textured look.

FULLY OPERABLE AND RETRACTABLE

VENETIAN BLINDS WITHIN A DOUBLE
FAADE
Double faades are gaining in popularity
due to their energy savings. To increase
these saving further, Colt can provide large
venetian blinds that lower and track the
suns position for maximum shading
effectiveness. When the sky is overcast, the
blinds can be fully retracted to maximize
views to the outside and the natural
daylight entering the building.

PHOTOVOLTAIC LOUVERS WITH

INTEGRATED DAY LIGHTING
The Shadovoltaic (blue tinted) louvers in
the center of the shading louver system
generate power for the buildings use. Their
position is constantly adjusted as the
louvers track the suns position to maximize
the electricity generated. The Shadoprism
louvers (white tinted) above and below the
Shadovoltaic louvers reflect direct
sunlinght, while allowing indirect light for
natural daylight into the building.

INSERTS
Shadometal louvers can be provided with
the ability to accept an insert to compliment
the other elements of the buildings faade.
In this case terra cotta inserts were used to
make a striking architectural appearance.

29

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:19 AM Page 31

Portfolio of Selected Projects

30

NEW YORK TIMES HEADQUARTERS

New York, NY
Renzo Piano-Fox/ Fowle Architects
Operable Shadometal

SCHOOL OF ARCHITECTURE, UNIVERSITY OF VIRGINIA

Charlottesville, VA
William Sherman and SMBW Architects
Operable and Fixed Shadoglass

NORTHWEST VISTA (ACCD) COLLEGE LIBRARY

San Antonio, TX
Overland Partners Architects
Operable Shadometal

ONE RIVER TERRACE

Battery Park, NY
Polshek Partnership and Ismael Leyva Architects
Operable Shadovoltaics and Shadowmetal

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:19 AM Page 32

PAPAGO GATEWAY CENTER

Tempe, AZ
Smith Group Architects
Operable Shadometal

HAMILTON COLLEGE
Clinton, NY
Butler Rogers Baskett Architects
Fixed Shadometal

ADVANCED ENERGY CENTER, SUNY STONYBROOK

Stonybrook, NY
Flad Architects
Operable Shadovoltaics

NATURE RESEARCH CENTER NC DEPARTMENT OF

ENVIRONMENT AND NATURAL RESOURCES
Raleigh, NC
OBrien/Atkins Associates
Operable Shadoprism

31

CSSLS-B-1_Solar_Shading_Systems 8/29/12 10:18 AM Page 1

CSSLS-B-1
MF 10 71 13 - Exterior Sun Control Devices

101 Linel Drive, Mooresville, IN 46158 317.831.5314 P 317.831.9260 F

www.linel.co

www.awv.com

www.coltgroupusa.com