Squat Calculation

Squat
When a ship moves forward through shallow water, the displaced water is not easily replaced,
thus resulting the ship to move vertically down. This bodily sinkage of the vessel is known as
squat. On most occasions, the forward motion of the ship causes squat, but squat will also occur
with a moored ship alongside a jetty if a tide is present.
It is difficult to calculate the magnitude of squat accurately. However, theoretical and empirical
methods of varying reliability exist.
Shallow Water Theory

The water depth H and the mean draught T of the static ship are widely used as the parameters to
define shallow water. If the ratio H/T drops below 1.5, one will, in general, experience a
measurable change in the draught of the ship (sinkage). As H/T approaches 1.0 (grounding), the
effect of shallow water increases significantly.
Another parameter of importance for the effect of shallow water is the ship speed V. The wave
pattern created when the ship travels forward depends upon the ship speed relative to the water
depth, as there is a maximum depth at which a free-standing wave can travel. If the power to the
engine(s) is maintained at the same setting as in deep water, the ship will slow down in shallow
water.
Definition of shallow water and deep water: Shallow water effect is normally measurable when
the under-keel clearance (H - T) drops below 50% of the static mean draught.
As the ship is generally not symmetrical about its half-length and because of the viscous effects
of water, the changes in pressure are not identical for the fore and aft parts of the hull. This causes
the ship to trim forward or astern depending on the hull shape. Thus, the magnitude of squat
depends on the hull shape, the side and under-keel clearance and the speed through the water.
When the ship approaches shallow water it will experience sinkage and trimming - squat - due to
changes in the vertical forces acting on the hull. Squat varies in proportion to the square of the
speed. A ship with a large block coefficient (greater than about 0.70) will normally tend to squat
by the bow.
Different approaches for predicting squat have been suggested in technical literature. The
methods cover both theoretical and empirical investigations. The theoretical methods (e.g. Tuck
& Taylor 1970) generally requires detailed information about the geometry of the hull as well as a
computer with adequate software. The empirical methods (e.g. Eryuzlu & Hausser 1978 and
Barrass 1979) are normally based on data from model tests or full-size ships and use the leading
hull parameters, the speed of the ship, and the principal geographical data.
Based on a review of ship squat in the literature and comparison of the different empirical
methods available, it has been found that the method proposed by Barrass (1979) appears to
provide results of reasonable accuracy.
SIGNS OF SHALLOW WATER EFFECT (One or more of the following)

1.
2.
3.
4.
Wave making increases, especially at the forward end of the ship.

Vessel becomes more sluggish to manoeuvre. A pilots quote, almost like being in porridge.
Draft indicators on the bridge or echo sounders will indicate changes in end drafts.
Propeller RPM indicator will show a decrease. If the ship is in open water conditions, i.e.
without breadth restrictions, this decrease may be up to 15% of the service RPM in deep
water. If the ship is in a confined channel, this decrease in RPM can be up to 20% of the
service RPM.
5. There will be drop in speed. If the ship is in open water conditions this decrease may be up to
30%. If the ship is in a confined channel such as a river or a canal then this decrease can be
up to 60%.
6. The ship may start to vibrate suddenly. This is because of the entrained water effects causing
the natural hull frequency to become resonant with another frequency associated with the
vessel.
7. Any rolling, pitching and heaving motions will be reduced as the ship moves from deep water
to shallow water conditions. This is because of the cushioning effects produced by the narrow
layer of water under the bottom shell of the vessel.
8. The appearance of the mud could suddenly show in the water around the ships hull say in the
event of passing over a raised shelf or a submerged wreck.
9. Turning circle diameter (TCD) increases. TCD in shallow water could increase 100%.
10. Stopping distances

is in deep waters.
and stopping times
increase,
compared
to when
a vessel
Calculating Squat:
CB x S0.81 x V2.08
Maximum Squat =
metres.
20
CB = Block co-eff.
S = Blockage factor =
Submerged cross section area of ship

Submerged cross section area of channel
= bxd
BxD
where b & d : breadth & draft of ship and B & D : breadth & depth of the channel respectively
V = Vessels speed relative to the water, in knots.
If the vessel is in open shallow water, B= Breadth of the channel is taken as:
B = {7.7 + 20 (1 CB )2 } x b, known as the width of influence.
The width of influence ranges from 8.25b for supertankers, to about 9.5b for general cargo ships
to about 11.75 ship breadths for container ships.
The presence of another ship in a narrow channel may cause the squats to double in value as they
pass/ cross the other vessel.
SHORT-CUT FORMULAE:
Maximum Squat =
CB x VK2
metres
100
(for open water conditions only, where D/d = 1.1 to 1.4)
CB x VK2
metres
50
(for confined channels only, where S = 0.100 to 0.265)
Maximum Squat =

Squat Calculation

Uploaded by

Copyright:

Available Formats

Squat Calculation

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Squat Calculation

Uploaded by

Copyright:

Available Formats

Squat

Shallow Water Theory

SIGNS OF SHALLOW WATER EFFECT (One or more of the following)

Wave making increases, especially at the forward end of the ship.

10. Stopping distances

and stopping times

Submerged cross section area of ship

You might also like