Yciv

Download as pdf or txt
Download as pdf or txt
You are on page 1of 334

AIR-COOLED SCREW LIQUID CHILLERS

INSTALLATION, OPERATION & MAINTENANCE

Supersedes 201.23-NM1 (510)

Form 201.23-NM1 (910)


035-21506-100

AIR-COOLED SCREW LIQUID CHILLERS


STYLE a

MODELS
YCIV0590-1500, 50 HZ
(590 -1500 kw)
E/V HIGH EFFICIENCY AND S/P STANDARD EFFICIENCY

R134a

FORM 201.23-NM1 (910)

IMPORTANT!

Read BEFORE PROCEEDING!


GENERAL SAFETY GUIDELINES
This equipment is a relatively complicated apparatus.
During installation, operation, maintenance or service,
individuals may be exposed to certain components or
conditions including, but not limited to refrigerants,
oils, materials under pressure, rotating components, and
both high and low voltage. Each of these items has the
potential, if misused or handled improperly, to cause
bodily injury or death. It is the obligation and responsibility of operating/service personnel to identify and
recognize these inherent hazards, protect themselves,
and proceed safely in completing their tasks. Failure
to comply with any of these requirements could result
in serious damage to the equipment and the property in

which it is situated, as well as severe personal injury or


death to themselves and people at the site.
This document is intended for use by owner-authorized
operating/service personnel. It is expected that this individual possesses independent training that will enable them to perform their assigned tasks properly and
safely. It is essential that, prior to performing any task
on this equipment, this individual shall have read and
understood this document and any referenced materials. This individual shall also be familiar with and
comply with all applicable governmental standards and
regulations pertaining to the task in question.

safety symbols

The following symbols are used in this document to alert the reader to areas of potential hazard:
DANGER indicates an imminently
hazardous situation which, if not
avoided, will result in death or serious injury.

CAUTION identifies a hazard which


could lead to damage to the machine,
damage to other equipment and/or
environmental pollution. Usually an
instruction will be given, together with
a brief explanation.

WARNING indicates a potentially


hazardous situation which, if not
avoided, could result in death or serious injury.

NOTE is used to highlight additional


information which may be helpful to
you.

External wiring, unless specified as an optional connection in the manufacturers product


line, is not to be connected inside the Micro Panel cabinet. Devices such as relays, switches,
transducers and controls may not be installed inside the panel. No external wiring is allowed to be run through the Micro Panel. All wiring must be in accordance with Johnson
Controls published specifications and must be performed only by qualified Johnson Controls personnel. Johnson Controls will not be responsible for damages/problems resulting
from improper connections to the controls or application of improper control signals. Failure
to follow this will void the manufacturers warranty and cause serious damage to property
or injury to persons.
2

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

CHANGEABILITY OF THIS DOCUMENT


In complying with Johnson Controls policy for continuous product improvement, the information contained
in this document is subject to change without notice.
While Johnson Controls makes no commitment to update or provide current information automatically to
the manual owner, that information, if applicable, can
be obtained by contacting the nearest Johnson Controls
Engineered Systems Service office.

It is the responsibility of operating/service personnel


to verify the applicability of these documents to the
equipment in question. If there is any question in the
mind of operating/service personnel as to the applicability of these documents, then prior to working on the
equipment, they should verify with the owner whether
the equipment has been modified and if current literature is available.

The Control/VSD Cabinet contains


lethal high AC and DC voltages. Before performing service inside the
cabinet, remove the AC supply feeding
the chiller and verify using a noncontact voltage sensor.

NEVER place loose tools, debris, or


any objects inside the Control Panel/
VSD Cabinet.

The DC voltage on the VSD DC Bus


will take 5 minutes to bleed off, after
AC power is removed. Always check
the DC Bus Voltage with a Voltmeter
to assure the capacitor charge has
bled off before working on the system.

NEVER allow the Control Panel VSD


Cabinet doors to remain open if there
is a potential for rain to enter the
panel. Keep doors closed and assure
all latchesare engaged on each door
unless the unit is being serviced.
ALWAYS lockout the disconnect supplying AC to the chiller.

NEVER short out the DC Bus to discharge the filter capacitors.


The 1L Line Inductor will reach operating temperatures of over 300 F.
DO NOT open panel doors during
operation. Assure the inductor is cool
whenever working near the inductor
with power OFF.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS
SECTION 1 - General chiller information and safety..................................................21
INTRODUCTION..........................................................................................................................................21
Warranty.................................................................................................................................................21
Safety........................................................................................................................................................21
Standards for Safety............................................................................................................................21
Responsibility for Safety.....................................................................................................................21
About this manual...............................................................................................................................22
Misuse of equipment............................................................................................................................22
Suitability for Application....................................................................................................................22
Structural Support................................................................................................................................22
Mechanical Strength ...........................................................................................................................22
General Access.....................................................................................................................................22
Pressure Systems................................................................................................................................22
Electrical................................................................................................................................................23
Rotating Parts.......................................................................................................................................23
Sharp Edges..........................................................................................................................................23
Refrigerants and Oils...........................................................................................................................23
High Temperature and Pressure Cleaning.........................................................................................23
Emergency Shutdown..........................................................................................................................23

SECTION 2 - Product description...........................................................................................25


Introduction..........................................................................................................................................25
General System Description................................................................................................................25
Compressor..........................................................................................................................................26
Evaporator.............................................................................................................................................27
Condenser.............................................................................................................................................27
Flash Tank Feed Valve/Drain Valves...................................................................................................28
Oil Separator/Oil System.....................................................................................................................28
Relief Valves..........................................................................................................................................28
Oil Cooling............................................................................................................................................29
Capacity Control...................................................................................................................................29
Power and Control Panel.....................................................................................................................29
Each Power Compartment Contains..................................................................................................29
Microprocessor and VSD Controls.....................................................................................................29
Display...................................................................................................................................................29
Keypad...................................................................................................................................................30
Unit Switch............................................................................................................................................30
Variable Speed Drive (VSD).................................................................................................................31

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


ACCESSORIES AND OPTIONS..................................................................................................................32
Sound Reduction Options...................................................................................................................32
Condenser Coil Protection..................................................................................................................33
Protective Chiller Panels.....................................................................................................................33
Evaporator Options..............................................................................................................................34
General Options....................................................................................................................................34
Vibration Isolation................................................................................................................................34
UNIT MODEL NUMBER NOMENCLATURE................................................................................................35
Complete pin number description.................................................................................................36

SECTION 3 - Handling and storage........................................................................................41


DELIVERY AND STORAGE.........................................................................................................................41
INSPECTION................................................................................................................................................41
MOVING THE CHILLER...............................................................................................................................41
Lifting Weights......................................................................................................................................41
Unit Rigging..........................................................................................................................................42

SECTION 4 - installation............................................................................................................45
LOCATION REQUIREMENTS.....................................................................................................................45
OUTDOOR INSTALLATIONS......................................................................................................................45
INDOOR INSTALLATIONS..........................................................................................................................45
LOCATION CLEARANCES.........................................................................................................................45
VIBRATION ISOLATORS.............................................................................................................................46
Installation.............................................................................................................................................46
SHIPPING BRACES.....................................................................................................................................46
CHILLED LIQUID PIPING............................................................................................................................46
General Requirements.........................................................................................................................46
WATER TREATMENT..................................................................................................................................47
REFRIGERANT RELIEF VALVE PIPING.....................................................................................................48
PIPEWORK ARRANGEMENT.....................................................................................................................48
CONNECTION TYPES and SIZES.............................................................................................................48
COOLER CONNECTIONS...........................................................................................................................48
Option Flanges.....................................................................................................................................48
DUCTWORK CONNECTION ......................................................................................................................49
General Requirements ........................................................................................................................49
ELECTRICAL CONNECTION......................................................................................................................49
POWER WIRING..........................................................................................................................................50
POWER SUPPLY WIRING...........................................................................................................................50
115VAC CONTROL SUPPLY TRANSFORMER..........................................................................................50
CONTROL PANEL WIRING.........................................................................................................................50
VOLTS FREE CONTACTS...........................................................................................................................51
Chilled Liquid Pump Starter................................................................................................................51
Run Contact..........................................................................................................................................51
Alarm Contacts.....................................................................................................................................51
6

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


SYSTEM INPUTS.........................................................................................................................................51
Flow Switch...........................................................................................................................................51
Remote Run / Stop...............................................................................................................................51
Remote Print.........................................................................................................................................51
Optional Remote Setpoint Offset Temperature..............................................................................51
Optional Remote Setpoint Offset Current.......................................................................................51
Optional Remote Setpoint Offset Sound Limiting..........................................................................51

SECTION 5 - Commissioning........................................................................................................53
PREPARATION............................................................................................................................................53
PREPARATION GENERAL.......................................................................................................................53
Inspection ............................................................................................................................................53
Refrigerant Charge...............................................................................................................................53
Service and Oil Line Valves.................................................................................................................53
Compressor Oil.....................................................................................................................................53
Fans ......................................................................................................................................................53
Isolation / Protection............................................................................................................................53
Control Panel........................................................................................................................................53
Power Connections..............................................................................................................................53
Grounding.............................................................................................................................................54
Water System........................................................................................................................................54
Flow Switch...........................................................................................................................................54
Temperature Sensor(s)........................................................................................................................54
Programmed Options...........................................................................................................................54
Programmed Settings .........................................................................................................................54
Date and Time.......................................................................................................................................54
Start/Stop Schedule.............................................................................................................................54
Setpoint and Remote Offset................................................................................................................54
FIRST TIME START-UP...............................................................................................................................54
Interlocks...............................................................................................................................................54
Unit Switch............................................................................................................................................55
Start-up..................................................................................................................................................55
Oil Pressure..........................................................................................................................................55
Refrigerant Flow...................................................................................................................................55
Loading..................................................................................................................................................55
Condenser and Fan Rotation..............................................................................................................55
Suction Superheat................................................................................................................................55
Subcooling............................................................................................................................................55
General Operation ...............................................................................................................................55
EQUIPMENT PRE-STARTUP and STARTUP CHECKLIST......................................................................56
Pre Start-up...........................................................................................................................................56
Start-up . ...............................................................................................................................................58

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


SECTION 6 - TECHNICAL DATA.......................................................................................................63
Water Pressure Drop Charts.........................................................................................................63
GLYCOL CORRECTION FACTORS............................................................................................................67
WATER TEMPERATURE AND FLOWS.......................................................................................................68
WATER TEMPERATURE AND FLOWS (CONT'D).....................................................................................69
Physical Data (English - Standard Efficiency).........................................................................70
PHYSICAL DATA (English - High Efficiency)....................................................................................72
PHYSICAL DATA (SI - Standard Efficiency).....................................................................................74
PHYSICAL DATA (SI - High Efficiency)................................................................................................76
Electrical data.....................................................................................................................................78
2 Compressor Power Wiring Connections.........................................................................................78
3 Compressor Power Wiring Connections.........................................................................................79
Electrical notes..................................................................................................................................92
Electrical wiring DIAGRAMS - 2 compressor models............................................................94
Elementary Power Wiring Diagram.....................................................................................................96
Power Wiring Connection Diagram....................................................................................................98
Control Wiring Connection Diagram................................................................................................100
Power Elementary Wiring Diagram...................................................................................................103
Location Label....................................................................................................................................105
Electrical wiring DIAGRAMS - 3 compressor models..........................................................108
Panel Layout.......................................................................................................................................108
Elementary Control Wiring Diagram.................................................................................................109
Control Elementary Diagram............................................................................................................. 111
Power Elementary Diagram...............................................................................................................113
Control Wiring Connection Diagram................................................................................................115
Power Wiring Connection Diagram..................................................................................................118
Location Label....................................................................................................................................124
Panel Layout.......................................................................................................................................125
Dimensions - 2 and 3 cOMPRESSOR SI.............................................................................................126
Technical data - clearances.........................................................................................................146
ISOLATOR INFORMATION FOR UNITS SHIPPED ON OR AFTER JUNE 15, 2008...............................147
Isolator Selection and Mounting.......................................................................................................147
One Inch Deflection Spring Isolators Cross-reference...................................................................164
One Inch Deflection Spring Isolators Installation Instructions......................................................165
Durulene Isolator Cross-reference...................................................................................................166
Installation of Durulene Vibration Isolators.....................................................................................167
Seismic Isolator Cross-reference.....................................................................................................168
Seismic Isolator Installation and Adjustment..................................................................................169

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)

ISOLATOR INFORMATION FOR UNITS SHIPPED BEFORE JUNE 15, 2008.........................................170


SLRS Seismic Isolator Specifications..............................................................................................170
SLRS Seismic Isolator Installation and Adjustment.......................................................................171
ND-X Neoprene Isolator Specifications............................................................................................172
CIP 1" Deflection Restrained Mounting Specifications..................................................................173
Installation of 1" Deflection Mounts.................................................................................................174
Refrigerant flow diagram............................................................................................................175
Process and instrumentation diagram....................................................................................176
Component locations.......................................................................................................................177
Glycol system components...........................................................................................................198
Compressor components...............................................................................................................200
Chiller electronic components.................................................................................................201
Keypad.................................................................................................................................................201
Display.................................................................................................................................................202
Relay Output Boards..........................................................................................................................203
VSD (Variable Speed Drive) ..............................................................................................................204
AC to DC Rectifier..............................................................................................................................204
SCR Trigger Board.............................................................................................................................204
DC Link Filter......................................................................................................................................204
1L Line Inductor . ...............................................................................................................................205
DC to AC Inverter................................................................................................................................205
Laminated Bus Structure...................................................................................................................206
VSD Logic Board................................................................................................................................206
Control Panel to VSD Communications...........................................................................................207
IGBT Gate Driver Boards...................................................................................................................207
Current Transformers.........................................................................................................................208
DV/DT Output Suppression Network................................................................................................208
Flash Tank Feed and Drain Valve Controller....................................................................................208
DC Bus Voltage Isolation Board........................................................................................................209
Chiller Circuit Breaker........................................................................................................................209
CHILLER CONFIGURATION JUMPERS...................................................................................................209
Number of Compressors Configuration Jumper.............................................................................209
VSD Logic to Chiller Microprocessor Board RS-485 Communication
Configuration Jumpers...................................................................................................................210
Maximum VSD Frequency/Model designator............................................................................210

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


SECTION 7 - OPERATION...............................................................................................................211
Operating controls..........................................................................................................................211
Anti-recycle Timer..............................................................................................................................211
Evaporator Pump Control..................................................................................................................211
Evaporator Heater Control.................................................................................................................211
Pumpdown Control............................................................................................................................211
Compressor Heater Control..............................................................................................................211
Alarms.................................................................................................................................................211
Chiller Run Contact............................................................................................................................211
Unit Switch..........................................................................................................................................212
Basic operating sequence.............................................................................................................212
Start Sequence and Loading.............................................................................................................212
Number of compressors to start..............................................................................................213
General................................................................................................................................................213
Standard IPLV.....................................................................................................................................213
Optional Optimized High IPLV...........................................................................................................213
Minimum vsd compressor start/run frequency...................................................................214
Minimum VSD Start Frequency.........................................................................................................214
Minimum VSD Run Frequency..........................................................................................................214
acceleration/deceleration RATE when starting/stopping compressors................215
VSD Acceleration and Deceleration Rates.......................................................................................215
Standard iplv capacity control..................................................................................................215
Fuzzy Logic Control...........................................................................................................................216
Hot Water Starts.................................................................................................................................217
Lag Compressor Operation in Load Limiting..................................................................................217
optional high iplv capacity control ........................................................................................217
Fuzzy Logic Control...........................................................................................................................219
Hot Water Starts.................................................................................................................................220
Load limiting control......................................................................................................................220
Load Limiting .....................................................................................................................................220
Motor Current Load Limiting/Unloading..........................................................................................220
Discharge Pressure Load Limiting/Unloading.................................................................................220
Suction Pressure Load Limiting/Unloading.....................................................................................221
VSD Internal Ambient Temperature Load Limiting..........................................................................221
VSD Baseplate Temperature Load Limiting.....................................................................................221
flash tank drain and feed valve controller.......................................................................222
Valve Controller and Control Algorithm Operation.........................................................................222
MOP Setpoint Control for Hot Water Starts.....................................................................................223
Moderate To High Ambient MOP Setpoint Control..........................................................................223
Low Ambient MOP Setpoint Control.................................................................................................223
Actual MOP Setpoint..........................................................................................................................223
Valve Controller LEDs.......................................................................................................................224

10

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


Economizer control.........................................................................................................................225
Condenser fan control..................................................................................................................226
Standard IPLV Fan Control ...............................................................................................................227
Optimized IPLV Fan Control .............................................................................................................227
High VSD Cabinet Ambient Temperature Fan Operation................................................................227
Vsd temperature control, operation of the coolant pump, and vsd
cabinet cooling fans........................................................................................................................227
remote temperature reset control.........................................................................................228
Temperature Reset Control...............................................................................................................228
Remote ISN Setpoint Control............................................................................................................228
Remote Temperature Reset...............................................................................................................228
Local Current Limit Control...............................................................................................................229
Pulldown Current Limit Setpoint.......................................................................................................229
remote current limit reset control........................................................................................229
Remote ISN Current Limit Setpoint..................................................................................................230
Remote Current Limit Reset..............................................................................................................230
sound limit control..........................................................................................................................231
Sound Limiting and Local Sound Limit Setpoint............................................................................231
ISN Sound Limit Setpoint..................................................................................................................231
Remote Sound Limit...........................................................................................................................231

SECTION 8 - MICROPANEL............................................................................................................233
vsd operation and controls.........................................................................................................233
VSD Logic Board................................................................................................................................233
VSD Start/run Initiation......................................................................................................................233
PWM Generator Type and Carrier Frequency..................................................................................233
Short Circuit Protection Minimum Output Pulse Width and Interlock Delay................................233
Modulating Frequency.......................................................................................................................233
Maximum VSD Frequency.................................................................................................................234
VSD % Modulation..............................................................................................................................234
VSD Cooling and Cooling Loop........................................................................................................234
IGBT Module Baseplate Temperature Sensing................................................................................235
VSD Internal Ambient Temperature Sensing...................................................................................236
Pre-charge...........................................................................................................................................236
Run Mode / Unit Restart.....................................................................................................................236
DC Bus Voltage Sensing and Scaling...............................................................................................237
Current Sensing and Scaling............................................................................................................237
VSD Transmitted Operating Parameters..........................................................................................237

JOHNSON CONTROLS

11

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


vsd safeties (faults).........................................................................................................................237
Pre-charge Low DC Bus Voltage (Software) Fault...........................................................................238
Pre-charge DC Bus Voltage Imbalance (Software) Fault................................................................239
High DC Bus Voltage (Hardware) Fault............................................................................................239
Low DC Bus Voltage (Software) Fault..............................................................................................239
DC Bus Voltage Imbalance (Software) Fault....................................................................................239
High Motor Current (Hardware) Fault...............................................................................................240
Motor Current Overload (Software) Fault.........................................................................................240
Motor Current Overload (Hardware) Fault........................................................................................240
IGBT Gate Driver (Hardware) Fault...................................................................................................240
High Baseplate Temperature (Software) Fault.................................................................................241
High VSD Internal Ambient Temperature (Software) Fault.............................................................241
Single Phase Input (Hardware) Fault................................................................................................241
Power Supply (Hardware) Fault .......................................................................................................242
Run Relay (Software) Fault . .............................................................................................................242
VSD Logic Board Failure (Software) Fault ......................................................................................242
VSD CT Plug (Hardware) Fault..........................................................................................................242
VSD Fault Data . .................................................................................................................................242
Fault Relay/Fault Acknowledge Bit...................................................................................................243
VSD Fault Compressor Start Inhibit ................................................................................................243
unit warnings.......................................................................................................................................243
Unit Warning Operation.....................................................................................................................243
Low Battery Warning..........................................................................................................................243
Invalid Number of Compressors Warning........................................................................................244
Invalid Serial Number Warning.........................................................................................................244
Optimized Efficiency Disabled..........................................................................................................244
unit safeties.........................................................................................................................................245
Unit Safety Operation.........................................................................................................................245
High Ambient Temp Fault..................................................................................................................245
Low Ambient Temp Fault...................................................................................................................245
Low Leaving Chilled Liquid Temp Fault...........................................................................................245
VSD Communications Failure Fault..................................................................................................246

12

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


system safeties (faults).................................................................................................................246
System Safety (Fault) Operation.......................................................................................................246
High Discharge Pressure Cutout (Software) Fault..........................................................................247
High Discharge Pressure Cutout (HPCO) (Hardware) Fault ..........................................................247
Low Suction Pressure Cutout (Software) Fault...............................................................................247
Low Motor Current Cutout Fault.......................................................................................................247
High Differential Oil Pressure Cutout Fault.....................................................................................248
Low Differential Oil Pressure Cutout Fault......................................................................................248
High Discharge Temperature Cutout Fault......................................................................................248
High Oil Temperature Cutout Fault...................................................................................................248
Low Suction Superheat Cutout Fault...............................................................................................249
Low Discharge Superheat Cutout Fault...........................................................................................249
Sensor Failure Cutout Fault..............................................................................................................249
High Motor Temperature Cutout Fault..............................................................................................250
High Flash Tank Level Cutout Fault..................................................................................................250
System Control Voltage Cutout Fault...............................................................................................250
status key..............................................................................................................................................251
Status Key Operation.........................................................................................................................251
General Status Messages..................................................................................................................252
Unit Safety (Fault) Status Messages.................................................................................................253
System Safety (Fault) Status Messages...........................................................................................253
VSD Safety (Fault) Status Messages................................................................................................253
Unit Warning Messages.....................................................................................................................253
unit data key.........................................................................................................................................254
General................................................................................................................................................254
Unit Data Key Operation....................................................................................................................254
system data keys 1 through 4.......................................................................................................256
General................................................................................................................................................256
System 1 Data Key Operation...........................................................................................................256
System 2 through 4 Data Key Operation..........................................................................................257
Sensor Displays..................................................................................................................................258
vsd data key..........................................................................................................................................259
General................................................................................................................................................259
VSD Data Key Operation....................................................................................................................259
operating hours / start counter key.......................................................................................261

JOHNSON CONTROLS

13

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


history key............................................................................................................................................262
History Key Operation........................................................................................................................262
Normal Shutdowns History...............................................................................................................262
Fault Shutdowns History...................................................................................................................263
Status Fault Type................................................................................................................................263
Unit Fault Type....................................................................................................................................263
All Fault Data.......................................................................................................................................263
Unit Data..............................................................................................................................................264
VSD Data.............................................................................................................................................264
System Data........................................................................................................................................265
Compressor Operating Hours and Starts........................................................................................266
Chilled Liquid Setpoint Cooling Setpoints.......................................................................................267
Options................................................................................................................................................267
Remote Temperature Reset...............................................................................................................267
Program Values..................................................................................................................................268
Pulldown Current Limit......................................................................................................................268
setpoints key.......................................................................................................................................269
Setpoints Key Operation....................................................................................................................269
Program key.........................................................................................................................................271
Program Key Operation.....................................................................................................................271
Suction Pressure Cutout...................................................................................................................271
Low Ambient Cutout..........................................................................................................................272
Low Leaving Liquid Temp Cutout.....................................................................................................272
Motor Current Limit............................................................................................................................272
Pulldown Current Limit......................................................................................................................272
Pulldown Current Limit Time.............................................................................................................272
Suction Superheat Setpoint..............................................................................................................272
Unit ID Number...................................................................................................................................272
Sound Limit Setpoint.........................................................................................................................273
Default Values.....................................................................................................................................273
options key...........................................................................................................................................274
Options Key Operation......................................................................................................................274
Display Language Selection..............................................................................................................274
Chilled Liquid Cooling Mode Selection............................................................................................274
Local / Remote Control Mode Selection...........................................................................................275
Display Units Selection......................................................................................................................275
System Lead/Lag Control Mode Selection.......................................................................................275
Remote Temperature Reset Selection..............................................................................................276
Remote Current Limit Input Selection..............................................................................................276
Remote Sound Limit Selection..........................................................................................................276
Low Ambient Cutout Enable/Disable................................................................................................276

14

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE OF CONTENTS (CONT'D)


date/time and schedule keys.........................................................................................................277
Date/Time Key Operation...................................................................................................................277
Schedule Key Operation....................................................................................................................278
Unit Operating Schedule....................................................................................................................279
Sound Limit Schedule........................................................................................................................280
manual override key........................................................................................................................281
Manual Overrride Key Operation......................................................................................................281
print key.................................................................................................................................................282
Print Key Operation............................................................................................................................282
Operating Data Printout.....................................................................................................................283
History Data Printout..........................................................................................................................284
SERVICE KEY............................................................................................................................................285
Service Key Operation.......................................................................................................................285
SYSTEM SWITCHES KEY.........................................................................................................................291
System Switches Key Operation.......................................................................................................291
Serial Number Programming.........................................................................................................292
enabling optimized high iplv mode..............................................................................................293
unit setup mode...................................................................................................................................294
default programmable values....................................................................................................295
serial port connections................................................................................................................295
analog input connections.............................................................................................................296
digital inTput connections............................................................................................................298
analog OUTput connections.........................................................................................................299
digital OUTput connections...........................................................................................................300
BACNET, MODBUS AND YORKTALK 2 COMMUNICATIONS.................................................................302
BACnet and Modbus Communications............................................................................................305
Communications Data Map Notes....................................................................................................305
Yorktalk 2 Communications..............................................................................................................309

Section 9 - maintenance..........................................................................................................313
R-134a conversion tables...............................................................................................................313
General Requirements....................................................................................................................314
Daily Maintenance..............................................................................................................................314
Unit Status...........................................................................................................................................314
Refrigerant Leaks...............................................................................................................................314
Operating Conditions.........................................................................................................................314
Compressor Oil Level........................................................................................................................314
Refrigerant Charge.............................................................................................................................314
Scheduled Maintenance.....................................................................................................................314
Chiller / Compressor Operating Log.................................................................................................314
maintenance requirements for yciv chillers.......................................................................315
troubleshooting guide ..................................................................................................................316
Evacuating A System..........................................................................................................................318

JOHNSON CONTROLS

15

TABLE OF CONTENTS (CONT'D)


limited warranty................................................................................................................................319
Warranty on New Equipment.............................................................................................................319
Warranty on Reconditioned or Replacement Materials..................................................................319
All Warranties and Guarantees Are Void If:......................................................................................319
chilled liquid and suction temperature sensor input voltage ..................................320
printer wiring......................................................................................................................................327
Printer Cables.....................................................................................................................................328
Printer Setup.......................................................................................................................................328
Okidata 184.........................................................................................................................................328
Weigh-tronix IMP 24 Model 2600.......................................................................................................328
Seiko....................................................................................................................................................328
operating log sheet.........................................................................................................................329
Site and Chiller Information...............................................................................................................329
Programmed Values...........................................................................................................................329
System Operating Conditions...........................................................................................................331
Water System Conditions..................................................................................................................332
recommended spare parts.............................................................................................................333

FORM 201.23-NM1 (910)

list of figures
FIG. 1 - PWM CURRENT WAVEFORM............................................................................................................31
FIG. 2 - PWM Voltage Waveform.............................................................................................................31
FIG. 3 - PIPEWORK ARRANGEMENT............................................................................................................48
FIG. 4 - victaulic groove..........................................................................................................................48
FIG. 5 - flange attachment.....................................................................................................................48
FIG. 6 - two COMPressor WIRING DIAGRAM WITH CIRCUIT BREAKER.............................................78
FIG. 7 - two COMPressor WIRING DIAGRAM WITH TERMINAL BLOCK..............................................78
FIG. 8 - three COMPressor WIRING DIAGRAM WITH CIRCUIT BREAKER Single Point............79
FIG. 9 - Three COMPressor WIRING DIAGRAM WITH TERMINAL BLOCK Single Point.............79
FIG. 10 - elementary CONTROL wiring diagram 2 compressor models...................................94
FIG. 11 - elementary POWER wiring diagram - yciv0590-1000 2 compressor models...........96
FIG. 12 - power wiring Connection diagram - yciv0590-1000 2 compressor models...........98
FIG. 13 - control wiring Connection diagram - YCIV0590-1000 2 compressor models . ..100
FIG. 14 - power elementary wiring diagram - yciv0590-1000 2 compressor models.........103
FIG. 15 - control elementary diagram - yciv1050-1500 3 compressor models...................108
FIG. 16 - control elementary diagram - yciv1050-1500 3 compressor models................... 110
FIG. 17 - power elementary diagram - yciv1050-1500 3 compressor models....................... 112
FIG. 18 - control wiring connection diagram - yciv1050-1500 3 compressor models..... 114
FIG. 19 - power wiring connection diagram - yciv1050-1500 3 compressor models......... 118
FIG. 20 - power elemenetary diagram - yciv1050-1500 3 compressor models.....................122
FIG. 21 - refrigerant flow diagram....................................................................................................175
FIG. 22 - process and instrumentation diagram............................................................................176
FIG. 23 - component locations..............................................................................................................177
FIG. 24 - control and vsd cabinet components.............................................................................178
FIG. 25 - chiller control board, relay boards, microgateway, and
optional circuit breaker.......................................................................................................179
FIG. 26 - chiller control board, relay boards, and microgateway, 2 Compressor ....180
FIG. 27 - chiller control board, relay boards, and microgateway, 3 Compressor ....181
FIG. 28 - VSD LOGIC BOARD.........................................................................................................................182
FIG. 29 - VSD LOGIC BOARD (original - obsolete), P/N 031-02477-000............................................183
FIG. 30 - VSD LOGIC BOARD (NEW), P/N 031-02507-XXX ..........................................................................184
FIG. 31 - Power components, 2 compressor....................................................................................185
FIG. 32 - Power components, 3 compressor....................................................................................186
FIG. 33 - FAN CONTACTORS AND 3T transformer, 2 COMPRESSOR................................................187
FIG. 34 - FAN CONTACTORS, 3 COMPRESSOR...........................................................................................188
FIG. 35 - VSD Components.........................................................................................................................189
FIG. 36 - VSD Components, 2 COMPRESSOR..........................................................................................190
FIG. 37 - VSD Components, 3 COMPRESSOR..........................................................................................191
FIG. 38 - VSD Components, 2 COMPRESSOR..........................................................................................192
FIG. 39 - VSD Components, 3 Compressor..........................................................................................193
FIG. 40 - Inverter power Components, 2 COMPRESSOR.................................................................194
FIG. 41 - Inverter power Components, 3 COMPRESSOR.................................................................195
FIG. 42 - Inverter power Components................................................................................................196
FIG. 43 - glycol pump & fill tube locations.....................................................................................198
JOHNSON CONTROLS

17

FORM 201.23-NM1 (910)

list of figures (CONT'D)


FIG. 44 - glycol piping and fill tube location................................................................................199
FIG. 45 - compressor components.......................................................................................................200
fig. 46 - NEW BOARD P/N 031-02507-000....................................................................................................206
fig. 47 - OBSOLETE BOARD P/N 031-02477-000.........................................................................................206
FIG. 48 - chiller control (cooling) range.......................................................................................213
FIG. 49 - number of compressors to start.....................................................................................214
FIG. 50 - minimum vsd start frequency..............................................................................................214
FIG. 51 - minimum vsd RUN frequency..................................................................................................215
FIG. 52 - flash tank drain and feed valve controller..............................................................222
FIG. 53 - LED LOCATIONS..............................................................................................................................224
FIG. 54 - power and comms led's . ........................................................................................................224
FIG. 55 - power, comms and system open/close led's.................................................................224
FIG. 56 - CONDENSER FAN LOCATIONS......................................................................................................226
FIG. 57 - standard iplv fan control....................................................................................................227
FIG. 58 - HIGH iplv fan control...............................................................................................................227
fig. 59 - CONTROL BOARD Connections................................................................................................303
fig. 60 - print cable - chiller to serial printer...........................................................................327

18

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

list of Tables
TABLE 1 - C
 OMPRESSORS AND THE APPROPRIATE JUMPER POSITIONS............................................209
TABLE 2 - V
 SD logic board address jumper....................................................................................210
TABLE 3 - maximum frequency / Model designator jumper.......................................................210
TABLE 4 - fuzzy logic loading/unloadingvs. error....................................................................217
TABLE 5 - fuzzy logic loading/unloading vs. error...................................................................219
TABLE 6 - current limit load limiting/unloading..........................................................................220
TABLE 7 - discharge pressure load limiting/unloading...........................................................221
TABLE 8 - suction pressure load limiting/unloading.................................................................221
TABLE 9 - V
 SD internal ambient load limiting/unloading..........................................................221
TABLE 10 - vsd baseplate temperatureload limiting/unloading...........................................222
table 11 - fan stages and corresponding outputs....................................................................226
TABLE 12 - VSD operating display parameters...............................................................................237
TABLE 13 - low differential oil pressure cutout........................................................................248
TABLE 14 - start inhibit sensor thresholds...................................................................................250
TABLE 15 - sensor min/max outputs.....................................................................................................258
TABLE 16 - setpoint limits........................................................................................................................270
TABLE 17 - programmable operating parameters.......................................................................273
TABLE 18 - printout types.......................................................................................................................282
TABLE 19 - unit setup programmable values.................................................................................294
TABLE 20 - serial port connections...................................................................................................296
TABLE 21 - analog input connections................................................................................................296
TABLE 22 - digital input connections ................................................................................................298
TABLE 23 - analog output connections............................................................................................299
TABLE 24 - digital output connections.............................................................................................300
table 25 minimum, maximum and default values.........................................................................303
table 26 VALUES REQUIRED FOR BAS COMMUNICATION..................................................................304
TABLE 27 REAL TIME ERROR NUMBERS.................................................................................................304
TABLE 28 - BACNET AND MODBUS COMMUNICATIONS DATA MAP........................................................306
TABLE 29 - YorkTalk 2 COMMUNICATIONS DATA MAP..........................................................................310
TABLE 30 - R-134a pressure to saturated temperature conversion....................................313
TABLE 31 - temperature input voltage sensor (measured signal to SHIELD
AT THE SENSOR).........................................................................................................................320
TABLE 32 - outside air temperature sensor input voltage (measured signal to
SHIELD AT THE SENSOR)..........................................................................................................321
TABLE 33 - pressure transducer OUTput voltage (measured signal to
return AT THE TRANSDUCER)...............................................................................................322
TABLE 34 - motor temperature sensor resistance (CHECK AT THE MOTOR).........................323
TABLE 35 - Compressor motor overload settings and Max. vsd frequency...................324

JOHNSON CONTROLS

19

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

20

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SECTION 1 - General chiller information and safety


INTRODUCTION
YORK YCIV0590-1500 chillers are manufactured to
the highest design and construction standards to ensure
high performance, reliability and adaptability to all
types of air conditioning installations.
The unit is intended for cooling water or glycol solutions and is not suitable for purposes other than those
specified in this manual.
This manual contains all the information required for
correct installation and commissioning of the unit, together with operating and maintenance instructions.
The manuals should be read thoroughly before attempting to operate or service the unit.
All procedures detailed in the manuals, including installation, commissioning and maintenance tasks must
only be performed by suitably trained and qualified
personnel.
The manufacturer will not be liable for any injury or
damage caused by incorrect installation, commissioning, operation or maintenance resulting from a failure
to follow the procedures and instructions detailed in
the manuals.
Warranty
Johnson Controls warrants all equipment and materials
against defects in workmanship and materials for a period of eighteen months from date of shipment, unless
labor or extended warranty has been purchased as part
of the contract.
The warranty is limited to parts only replacement and
shipping of any faulty part, or sub-assembly, which has
failed due to poor quality or manufacturing errors. All
claims must be supported by evidence that the failure
has occurred within the warranty period, and that the
unit has been operated within the designed parameters
specified.
All warranty claims must specify the unit model, serial number, order number and run hours/starts. Model
and serial number information is printed on the unit
identification plate.
The unit warranty will be void if any modification to
the unit is carried out without prior written approval
from Johnson Controls.
JOHNSON CONTROLS

For warranty purposes, the following conditions must


be satisfied:
The initial start of the unit must be carried out by
trained personnel from an authorized Johnson Controls Service Center. See Commissioning (Page
53).
Only genuine YORK approved spare parts, oils,
coolants, and refrigerants must be used. Recommendations on spare part stocking can be found on
Page 333.
All the scheduled maintenance operations detailed
in this manual must be performed at the specified
times by suitably trained and qualified personnel.
See Maintenance section, Pages 313-333.
Failure to satisfy any of these conditions will automatically void the warranty. See Warranty Policy
(Page 319).
Safety
Standards for Safety
YCIV chillers are designed and built within an ISO
9002 accredited design and manufacturing organization.
The chillers comply with the applicable sections of the
following Standards and Codes:
ANSI/ASHRAE Standard 15, Safety Code for Mechanical Refrigeration.
ANSI/NFPA Standard 70, National Electrical Code
(N.E.C.).
ASME Boiler and Pressure Vessel Code, Section
VIII Division 1.
ARI Standard 550/590-98, Water Chilling Packages
Using the Vapor Compression Cycle.
ASHRAE 90.1 Energy Standard for Building Except
Low-Rise Residential Buildings.
ARI 370 Sound Rating of Large Outdoor Refrigeration and Air Conditioning Equipment.
In addition, the chillers conform to Underwriters Laboratories (U.L.) for construction of chillers and provide
U.L./cU.L. Listing Label.
Responsibility for Safety
Every care has been taken in the design and manufacture of the unit to ensure compliance with the safety
21

GENERAL CHILLER INFORMATION AND SAFETY


requirements listed above. However, the individual
operating or working on any machinery is primarily
responsible for:
Personal safety, safety of other personnel, and the
machinery.
Correct utilization of the machinery in accordance
with the procedures detailed in the manuals.
About this manual
The following terms are used in this document to alert
the reader to areas of potential hazard.

A WARNING is given in this document to identify a


hazard, which could lead to personal injury. Usually an
instruction will be given, together with a brief explanation and the possible result of ignoring the instruction.

FORM 201.23-NM1 (910)

This manual and any other document supplied with


the unit are the property of Johnson Controls which
reserves all rights. They may not be reproduced, in
whole or in part, without prior written authorization
from an authorized Johnson Controls representative.
Misuse of equipment
Suitability for Application
The unit is intended for cooling water or glycol solutions and is not suitable for purposes other than those
specified in these instructions. Any use of the equipment other than its intended use, or operation of the
equipment contrary to the relevant procedures may result in injury to the operator, or damage to the equipment.
The unit must not be operated outside the design parameters specified in this manual.
Structural Support
Structural support of the unit must be provided as indicated in these instructions. Failure to provide proper
support may result in injury to the operator, or damage
to the equipment and/or building.
Mechanical Strength

A CAUTION identifies a hazard which could lead to


damage to the machine, damage to other equipment
and/or environmental pollution. Usually an instruction
will be given, together with a brief explanation and the
possible result of ignoring the instruction.

A NOTE is used to highlight additional information,


which may be helpful to you but where there are no
special safety implications.
The contents of this manual include suggested best
working practices and procedures. These are issued for
guidance only, and they do not take precedence over
the above stated individual responsibility and/or local
safety regulations.
22

The unit is not designed to withstand loads or stresses


from adjacent equipment, pipework or structures. Additional components must not be mounted on the unit.
Any such extraneous loads may cause structural failure
and may result in injury to the operator, or damage to
the equipment.
General Access
There are a number of areas and features, which may
be a hazard and potentially cause injury when working
on the unit unless suitable safety precautions are taken.
It is important to ensure access to the unit is restricted
to suitably qualified persons who are familiar with the
potential hazards and precautions necessary for safe
operation and maintenance of equipment containing
high temperatures, pressures and voltages.
Pressure Systems
The unit contains refrigerant vapor and liquid under
pressure, release of which can be a danger and cause
injury. The user should ensure that care is taken during
installation, operation and maintenance to avoid damage to the pressure system. No attempt should be made
to gain access to the component parts of the pressure
system other than by suitably trained and qualified personnel.
JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Electrical

Refrigerants and Oils

The unit must be grounded. No installation or maintenance work should be attempted on the electrical
equipment without first switching power OFF, isolating and locking-off the power supply. Servicing and
maintenance on live equipment must not be attempted.
No attempt should be made to gain access to the control panel or electrical enclosures during normal operation of the unit.

Refrigerants and oils used in the unit are generally nontoxic, non-flammable and non-corrosive, and pose no
special safety hazards. Use of gloves and safety glasses
is, however, recommended when working on the unit.
The buildup of refrigerant vapor, from a leak for example, does pose a risk of asphyxiation in confined or
enclosed spaces and attention should be given to good
ventilation.

Rotating Parts

High Temperature and Pressure Cleaning

Fan guards must be fitted at all times and not removed


unless the power supply has been isolated. If ductwork
is to be fitted, requiring the wire fan guards to be removed, alternative safety measures must be taken to
protect against the risk of injury from rotating fans.

High temperature and pressure cleaning methods (e.g.


steam cleaning) should not be used on any part of the
pressure system as this may cause operation of the pressure relief device(s). Detergents and solvents, which
may cause corrosion, should also be avoided.

Sharp Edges

Emergency Shutdown

The fins on the air-cooled condenser coils have sharp


metal edges. Reasonable care should be taken when
working in contact with the coils to avoid the risk of
minor abrasions and lacerations. The use of gloves is
recommended.

In case of emergency, the control panel is fitted with a


UNIT switch to stop the unit in an emergency. When
operated, it removes the low voltage 120VAC electrical supply from the inverter system, thus shutting down
the unit.

Frame rails, brakes, and other components may also


have sharp edges. Reasonable care should be taken
when working in contact with any components to avoid
risk of minor abrasions and lacerations.

JOHNSON CONTROLS

23

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

24

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SECTION 2 - Product description

Introduction

General System Description

YORK YCIV R134a chillers are designed for water or


glycol cooling. All units are designed to be located outside on the roof of a building or at ground level.

The Latitude (YCIV) Air-Cooled Chiller line combines


the best of modern screw compressor design with the
latest technology in variable speed drives. The result is
superior control and efficiency in real world conditions.
The VSD enables slowing the speed of the compressor
to match the load on the system resulting in precise
chilled liquid control, minimized sound, maximum energy efficiency, and reduced cost of ownership. The
VSD also provides soft starts with no electrical inrush.
The lack of heat build-up on start also enables required
off time between starts to be reduced to a period of 2
minutes.

The units are completely assembled with all interconnecting refrigerant piping and internal wiring, ready
for field installation.
Prior to delivery, the unit is pressure tested, evacuated,
and fully charged with refrigerant and oil in each of
the two independent refrigerant circuits. After assembly, an operational test is performed with water flowing through the cooler to ensure that each refrigerant
circuit operates correctly.
The unit structure is manufactured from heavy gauge,
galvanized steel. Many external structural parts are
coated with Champagne baked-on enamel powder
paint. This provides a finish which, when subjected to ASTM B117, 1000 hour, 5% salt spray conditions, shows breakdown of less than 1/8" either side
of a scribed line (equivalent to ASTM D1654 rating
of 6).
All exposed power wiring is routed through liquidtight, non-metallic conduit.

JOHNSON CONTROLS

The YCIV Air-Cooled Screw Chiller utilizes many


components, which are the same or nearly the same as
a standard screw chiller of a similar size. This includes
modular frame rails, condenser, fans, compressors and
evaporator.
The chiller consists of 2 or 3 screw compressors in a
corresponding number of separate refrigerant circuits,
a single shell and tube DX evaporator, an air-cooled
condenser, flash tanks, drain/feed valves, oil separators, and compressor mufflers. Oil separators utilize
no moving parts and are rated for a 405 PSIG design
working pressure. Oil cooling is accomplished by
routing oil from the oil separator through several rows
of tubes in the air cooled condenser.
25

PRODUCT DESCRIPTION
FORM 201.23-NM1 (910)

An integral liquid cooled, transistorized, PWM, Variable Speed Drive (VSD) is controlled by the chiller
microprocessor control panel to start/stop, select compressors to run, and select compressor speed. Power
Factor is 95% at part or full load.
The chiller microprocessor communicates with the
VSD Logic Board via a 3-wire RS-485 opto coupled
data link. The VSD Logic Board runs the number of
compressors required to meet the load and the compressors to the speed requested by the chiller microprocessor.
The basic system control architecture is shown in the
diagram below:
CHILLER CONTROL SYSTEM
INPUTS
Pressure Transducers
Temperature Sensors
Level Sensor
Switches
Liquid Flow
High Pressure
Start/Stop
Customer Supplied
Contacts

COMMUNICATIONS
Building Automation
Printer
Modem

OUTPUTS
(Relay Output
Board)

CONTROL
PANEL

(Chiller Control
Board)

Microprocessor
User Interface
Display
&
Keypad

Solenoids
Contactors
Alarm
Pump
Compressor Heater
Run Status
Evap Heater

VSD

VSD Logic Board


SCR Trigger Board
Power Components
PWM (Speed Control)

Refrigerant gas is injected into the void created by the


un-meshing of the five lobed male and seven lobed female rotors. Further meshing of the rotors closes the
rotor threads to the suction port and progressively compresses the gas in an axial direction to the discharge
port. The gas is compressed in volume and increased
in pressure before exiting at a designed volume at the
discharge end of the rotor casing. Since the intake and
discharge cycles overlap, a resulting smooth flow of
gas is maintained.
The rotors are housed in a cast iron compressor housing precision machined to provide optimal clearances
for the rotors. Contact between the male and female
rotor is primarily rolling on a contact band on each of
the rotors pitch circle. This results in virtually no rotor
wear and increased reliability, a trademark of the screw
compressor.
The MTS compressor incorporates a complete antifriction bearing design for reduced power input and
increased reliability. Separated, cylindrical, roller bearings handle radial loads. Angular-contact ball bearings
handle axial loads. Together they maintain accurate rotor positioning at all pressure ratios, thereby minimizing leakage and maintaining efficiency.

MOTOR

LD10478

The chiller is designed to operate in ambient temperatures of 0F to 125F (-18C to 52C). Capacity control is capable of reducing chiller capacity to 10% of
full load without the need for Hot Gas Bypass.
Compressor
The direct drive semi-hermetic rotary twin-screw MTS
compressor is designed for industrial refrigeration applications and ensures high operational efficiencies and
reliable performance. Capacity control is achieved by
stepless VSD speed changes. No slide valve is required. Smooth capacity control is achieved between
10% and 100% of chiller capacity in most operating
conditions. The compressor is a positive displacement type characterized by two helically grooved rotors, which are manufactured from forged steel. The 4
pole motor operates at speeds up to 6000 RPM to direct
drive the male rotor, which in turn drives the female
rotor on a light film of oil.
26

LD10481

LD10482

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Motor cooling is provided by suction gas from the evaporator flowing across the motor. Redundant overload
protection is provided using both internal thermistor
and current overload protection on all three phases.
The MTS compressor is lubricated by removing oil
from the refrigerant using an external oil separator. The
pressurized oil is then cooled in the condenser coils
and piped back to the compressor through a removable
0.005" mesh screen oil filter to provide compressor
lubrication. The cast iron compressor housing design
working pressure is 450 PSIG (31 bar). Each chiller
receives a 300 PSIG (21 bar) low side and a 450 PSIG
(31 bar) high side factory test. A 350 Watt (115-1-60
Hz) cartridge heater is located in the compressor. The
heater is temperature activated to prevent refrigerant
condensation.
The following items are also included:
Acoustically tuned, external discharge muffler to
minimize noise, while optimizing flow for maximum performance.
Discharge shutoff valve.
Rain-tight terminal box.
Suction gas screen within the compressor housing.
Evaporator
The system uses a high-efficiency shell and tube type
Direct Expansion Evaporator. Each of the two or three
refrigerant circuits consists of two (2) passes with the
chilled liquid circulating back and forth across the
tubes from one end to the other.
The design working pressure of the cooler on the shell
side is 150 PSIG (10 bar), and 235 PSIG (16 bar) for
the tube (refrigerant) side. The evaporator is constructed and tested in accordance with applicable sections of
the ASME Pressure Vessel Code, Section VII, Division
(1). Waterside exempt per paragraph U-1, c, (6).
The water baffles are fabricated from galvanized steel
to resist corrosion. Removable heads are provided for
access to internally enhanced, seamless, copper tubes.
Water vent and drain connections are included.
The cooler is equipped with a thermostatically controlled heater for protection to -20F (-29C) ambient
and insulated with 3/4" (19 mm) flexible closed-cell
insulation.

JOHNSON CONTROLS

The water nozzles are provided with grooves for mechanical couplings and should be insulated by the contractor after pipe installation.
A 300 PSIG (20.7 bar) waterside design working pressure option is available.
Two compressor chillers utilize a typical 2-pass E
type evaporator with liquid inlets and suction outlets at
the same end. Entering chilled liquid enters the refrigerant liquid inlet end of the cooler and leaving chilled
liquid exits at the opposite end.
Three compressor chillers utilize a single pass J type
evaporator with liquid inlets at one end and suction
outlets at the opposite end. Entering chilled liquid is
split and half flow enters at each end of the evaporator
with leaving chilled liquid exiting in the center of the
evaporator. J type evaporators have fewer, longer
tubes than a comparable E type. This results in a
smaller diameter, longer shell. Water flow rate internally in the evaporator is of the total loop flow rate
since the flow is split between two inlets. This results
in a low evaporator water pressure drop.
Condenser
The fin and tube condenser coils are manufactured
from seamless, internally enhanced, high-condensing
coefficient, corrosion-resistant copper tubes arranged
in staggered rows and mechanically expanded into corrosion resistant aluminum alloy fins with full height fin
collars. The condenser has a design working pressure
of 450 PSIG (31 bar).
Multiple, standard low sound, high efficiency, TEAO
motor driven fans move air through the coils. They are
dynamically and statically balanced, direct drive with
corrosion-resistant glass fiber reinforced composite
blades molded into low-noise, full airfoil cross sections, providing vertical air discharge from extended
orifices for efficiency and low sound. Fans or pairs of
fans are located in a separate compartments separated
by V panels to prevent cross flow during fan cycling.
Guards of heavy-gauge, PVC-coated galvanized steel
are provided.
The standard fan motors are high-efficiency, direct
drive, 6-pole, 3-phase, Class- F, current overload
protected, totally enclosed (TEAO) type with doublesealed, permanently lubricated ball bearings.

27

PRODUCT DESCRIPTION
FORM 201.23-NM1 (910)

Flash Tank Feed Valve/Drain Valves

Oil Separator/Oil System

A flash tank is fitted to both refrigerant circuits. The


flash tank is a shell type refrigerant reservoir designed
to sustain 2 phase refrigerant. The purpose of the flash
tank is to increase the efficiency of the system. A portion of the liquid fed into the flash tank gases off, cooling the remaining liquid in the tank another 25-35F.
Both liquid and gas exist in the flash tank. The refrigerant gas in the flash tank is fed to the economizer port
on the compressor at a point on the rotors approximately 1.7 x suction when the economizer solenoid is activated. The liquid in the tank is fed to the evaporator.

The external oil separators, with no moving parts and


designed for minimum oil carry-over, are mounted in
the discharge line of the compressor. The high pressure
discharge gas is forced around a 90 degree bend. Oil is
forced to the outside of the separator through centrifugal action and captured on wire mesh where it drains to
the bottom of the oil separator and is then forced into
the condenser.

The vapor feed to the economizer port of the compressor is at an intermediate pressure between discharge
and suction (1.7 x suction) and therefore little energy
is required to pump it back through the compressor to
condenser pressure. This results in a very small loss to
system efficiency.
The design working pressure of the flash tank is 450
PSIG (31 bar). The Drain and Feed Valves on the flash
tank are activated on start-up. The Feed Valve on the
flash tank acts like a liquid line solenoid, but also functions to control the liquid level in the flash tank. The
Drain Valve functions similar to an electronic expansion valve (EEV). The Drain Valve controls refrigerant flow to the evaporator based on suction superheat.
Both valves are stepper motor valves. An economizer
solenoid is placed between the flash tank and the economizer port of the compressor. The economizer solenoid valve is generally activated at speeds above 90 to
120 Hz, depending upon a number of other factors.
Both valves are controlled by 2 phase drive signals from
a stand-alone controller in the Control. Signals from
sensors such as suction pressure and temperature are
sent to the Chiller Control Board, which in turn sends
control signals to the Drain and Feed Valve Controller.
The control algorithm in the Chiller Control Board will
attempt to control the liquid level in the flash tank to
35% on the level sensor and the system will fault if the
flash tank level exceeds 87.5%.
During operation, it will be noted the flash tank level
will typically remain between 30-40% level when the
economizer solenoid is ON. The economizer solenoid
valve will typically be on most of the time. When the
economizer solenoid is OFF, the liquid level will vary
greatly as the Drain and Feed Valves directly affect the
level as they open and close.

28

The oil (YORK L oil a POE oil used for all refrigerant applications), flows from the oil separator,
through the condenser where it is cooled, and back into
the compressor through a replaceable 0.5 micron oil
filter at high pressure. This high pressure oil injection forces the oil into the compressor, where it is fed
to the bearings and rotors for lubrication. After lubricating the bearings, it is injected through orifices on a
closed thread near the suction end of the rotors. The oil
is automatically injected because of the pressure difference between the discharge pressure and the reduced
pressure at the suction end of the rotors. This lubricates
the rotors as well as provides an oil seal against leakage around the rotors to ensure refrigerant compression
efficiency.
The oil also provides cooling by transferring much of
the heat of compression from the gas to the oil, keeping
discharge temperatures down and reducing the chance
for oil breakdown. Oil injected into the rotor cage flows
into the rotors at a point about 1.2 x suction. This ensures that a required minimum differential of at least
30 PSID exists between discharge and 1.2 x suction, to
force oil into the rotor case. A minimum of 10 PSID
(0.6 bar) is all that is required to ensure protection of
the compressor. The oil pressure safety is monitored as
the difference between suction pressure and the pressure of the oil entering the rotor case.
Maximum working pressure of the oil separator is 450
PSIG (31 bar). Oil level should be above the midpoint
of the lower oil sight glass when the compressor is
running. Oil level should not be above the top of the
upper sight glass.
Relief Valves
Two relief valves are installed in each refrigerant circuit. A 325 PSIG relief valve is located on each flash
tank and a 250 PSIG relief valve is located on the suction line of the compressor near the evaporator.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Oil Cooling
Oil cooling is provided by routing oil from the oil separator through several of the top rows of the condenser
coils and back to the compressor.
Capacity Control
When cooling is needed, one or more compressors, as
determined by the system microprocessor based on deviation from setpoint, will start at minimum speed with
low inrush current. Variable speed operation of the
compressor reduces the capacity and allows smooth
balancing of the compressor capacity with the cooling
load.
Capacity control is accomplished by varying the number of compressors and the speed of the compressors
with the VSD to promote stable, smooth, and precise
loading/unloading.
Hot Gas Bypass is not required with VSD control of
the compressors.
The chiller is available with Standard IPLV or High
IPLV software (EPROM). High IPLV software optimizes the performance of the chiller capacity and fan controls. High IPLV chillers also require additional factory
programming.
Power and Control Panel
All controls and the VSD are factory-wired and function tested. The panel enclosures are designed to
NEMA 3R (IP65) rating and are manufactured from
powder-painted steel with hinged, latched, and gasket
sealed outer doors with wind struts for safer servicing.
The power and micro control panels are combined into
a single control/power cabinet and include:
Compressor VSD Controls.
Chiller Microprocessor Controls.
Fan Controls.
All Other Chiller Controls.
The Display and keypad are accessible through an access door without opening the main doors to the electrical cabinet.
Each Power Compartment Contains
Incoming single point power is standard utilizing either
a lockable circuit breaker or terminal block, 115VAC
control transformer, VSD, fan contactors, ON/OFF
unit switch, microcomputer keypad and display, Chiller Control and VSD Logic Boards, and relay boards.
JOHNSON CONTROLS

Current transformers sense each phase of motor current, and send corresponding signals to the Chiller
Logic Board. Current monitoring protects the compressor motors from damage due to low motor current,
high motor current, short circuit current, single phasing, and compressor overload.
Short Circuit Withstand Rating of the chiller electrical
enclosure is 30,000 Amps for standard terminal block
connection. Ratings are in accordance with UL508C.
A Circuit Breaker Option can be added to increase the
Short Circuit Withstand Rating to 200/230V equals
100,000 Amps, 380/460 V equals 65,000 Amps, and
575V equals 42,000 Amps.
Microprocessor and VSD Controls
Microprocessors on the Chiller Control Board and
VSD Logic Board control starting, stopping, loading,
unloading, safeties, and chilled liquid temperature
control. Chilled liquid control decisions are a function
of temperature deviation from setpoint and the rate of
change of temperature.
The standard controls include:
Brine Chilling.
Thermal Storage.
Run Signal Contacts.
Unit Alarm Contacts.
Chilled Liquid Pump Control.
Automatic reset after power failure.
Automatic system optimization to match operating
conditions.
Remote cycling, optional current limiting, optional
temperature setpoint reset, and optional remote sound
limit can be accomplished by connecting user-supplied
signals to the microprocessor.
Unit operating software is stored in non-volatile memory. Field programmed setpoints are retained in lithium battery backed real time clock (RTC) memory for
10 years.
Display
The display consists of a liquid crystal 2 line by 40
characters per line display, with backlighting for outdoor viewing of operating parameters and program
points.

29

PRODUCT DESCRIPTION
FORM 201.23-NM1 (910)

Parameters are displayed in 5 languages in either English (F and PSIG) or Metric (C and Bars) units, and
for each circuit, the following items can be displayed:
Entering and leaving chilled liquid, and ambient
temperature.
Day, date and time. Daily start/stop times. Holiday
and Manual Override status.
Compressor operating hours and starts. Automatic or
manual lead/lag. Lead compressor identification.
Run permissive status. Compressor run status.
Anti-recycle timers.
System suction (and suction superheat), discharge
(and discharge superheat), and oil pressures and
temperatures.
Percent full load compressor motor current and
average motor current. Compressor motor speed
(frequency).
Cutout status and setpoints for supply chilled liquid
temperature, low suction pressure, high discharge
pressure and temperature, high oil temperature, low
ambient, and low leaving liquid temperature.
Unloading limit setpoints for high discharge pressure and compressor motor current.
Status of evaporator heater, condenser fans, load/
unload timers, and chilled water pump.
Out of range message.
Up to 10 fault shutdown histories.

Keypad
An operator keypad allows complete control of the
system from a central location. The keypad utilizes
an overlay to allow use in 5 languages. The keypad is
a color-coded, 36 button, sealed keypad with keys for
Display, Entry, Setpoints, Clock, Print, Program, Unit
ON/OFF and other functions. Details on a few of the
keys follow:
Status Allows viewing present unit or system status
displayed by the microprocessor.
Entry Numeric keypad and supporting keys used to
confirm Setpoint changes, cancel inputs, advance day,
and change AM/PM.
Setpoints For setting chilled liquid temperature,
chilled liquid range, remote reset temperature range.
Date/Time Used to set time, daily or holiday start/
stop schedule, manual override for servicing, and
sound limiting schedule.
Print Used to display or print operating data or system fault shutdown history for last ten faults. Printouts
are generated through an RS-232 port via a separate
printer.
Program For setting low leaving liquid temperature
cutout, average motor current limit, and pulldown demand limit.
Displays are also provided for programming low ambient cutout, low suction pressure cutout, superheat
setpoint, etc., under the PROGRAM key.
Unit Switch
A master UNIT switch allows activation or de-activation of the chiller system. Separate system switches
for controlling each system are provided as part of the
chiller control panel keypad.

30

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Variable Speed Drive (VSD)


The VSD (variable speed drive) is a liquid cooled, transistorized, PWM inverter, which provides speed control to vary the speed of 2, 3 or 4 compressor motors.
The VSD changes the duration of the voltage pulses
supplied to the motor to enable control of compressor
speed to match the system load. A PWM generator, on
the VSD Logic Board, with a switching frequency of
3125 Hz modulates the voltage signal to provide a relatively pulses constant V/F ratio. In some cases, the V/F
ratio is slightly modified to provide additional torque
to the motor. Sample 3 phase current waveforms are
shown in FIG. 1 to show the sinusoidal characteristics
of the current drawn by the compressor motors.

LD10479

FIG. 1 - PWM CURRENT WAVEFORM

A Sample PWM voltage waveforms is shown in FIG.


2. The pulses near the sides of the rectangular groups
of waves are notably narrower, representing the lower
voltage of a sinusoidal waveform as it rises or falls
from the 0 crossing.

FIG. 2 - PWM Voltage Waveform

JOHNSON CONTROLS

The power section of the drive is composed of four major blocks consisting of an AC to DC rectifier section
with accompanying pre-charge circuit, a DC link filter
section, a three phase DC to AC inverter section, and
an output suppression network.
The AC to DC rectifier utilizes a semi-converter formed
by the connection of three SCR/diode modules (1SCR
through 3SCR) in a three phase bridge configuration.
The modules are mounted on a liquid cooled heatsink.
Use of the semi-converter configuration permits implementation of a separate pre-charge circuit to limit
the flow of current into the DC link filter capacitors
when the drive is switched on and it also provides a
fast disconnect from the power mains when the drive is
switched off. When the drive is turned off, the SCR's in
the semi-converter remain in a non-conducting mode
and the DC link filter capacitors remain uncharged.
When the drive is commanded to run, the DC link filter
capacitors are slowly charged via the semi-converter.
The SCRs are then gated fully on.
Three power fuses (1FU - 3FU), an optional circuit
breaker (1SW) and a standard 5% impedance minimum
3-phase line reactor connect the AC to DC converter to
the incoming power. Very fast semiconductor power
fuses are utilized to ensure that the SCR/diode module
packages do not rupture if a catastrophic failure were
to occur on the DC link. The SCR Trigger Board provides the gating pulses for the SCRs as commanded by
the VSD Logic Board.
The DC Link filter section of the drive consists of a
group of electrolytic filter capacitors (C1-C6). This
capacitor bank effectively smoothes the ripple voltage
from the AC to DC rectifier while simultaneously providing a large energy reservoir for use by the DC to
AC inverter section of the drive. In order to achieve
the required voltage capability for the capacitor portion of the filter, filter capacitor banks are formed by
connecting two groups of parallel capacitors in series
to form a capacitor bank. In order to assure an equal
sharing of the voltage between the series connected capacitors and to provide a discharge means for the capacitor bank when the VSD is powered off, bleeder
resistors (1RES and 2RES) are connected across the
capacitor banks.

LD10480

31

PRODUCT DESCRIPTION
FORM 201.23-NM1 (910)

The DC to AC inverter section of the VSD serves to


convert the rectified and filtered DC back to AC at the
magnitude and frequency commanded by the VSD
Logic Board. The inverter section is actually composed
of two to four identical inverter output phase assemblies. These assemblies are in turn composed of 3 pairs
of Insulated Gate Bipolar Transistor (IGBT) modules
mounted to a liquid cooled heatsink, and a IGBT Gate
Driver Board, which provides the ON and OFF gating
pulses to the IGBTs as determined by the VSD Logic
Board. In order to minimize the parasitic inductance
between the IGBTs and the capacitor banks, copper
plates, which electrically connect the capacitors to one
another and to the IGBTs are connected together using
a laminated bus structure.
This laminated bus structure is a actually composed
of a pair of copper bus plates with a thin sheet of insulating material acting as the separator/insulator. The
laminated bus structure forms a parasitic capacitor,
which acts as a small valued capacitor, effectively canceling the parasitic inductance of the bus bars themselves. To further cancel the parasitic inductances, a
series of small film capacitors are connected between
the positive and negative plates of the DC link.
The VSD output suppression network is composed
of a series of capacitors and resistors connected in a
three phase delta configuration. The parameters of the
suppression network components are chosen to work
in unison with the parasitic inductance of the DC to
AC inverter sections in order to simultaneously limit
both the rate of change of voltage and the peak voltage
applied to the motor windings. By limiting the peak
voltage to the motor windings, as well as the rate-ofchange of motor voltage, we can avoid problems commonly associated with PWM motor drives, such as
stator-winding end-turn failures and electrical fluting
of motor bearings.

on the board to provide a safe impedance (resistance)


between the DC link filter capacitors located on the output phase bank assemblies and the VSD Logic Board.
It provides the means to sense the positive, midpoint
and negative connection points of the VSDs DC link
without applying high voltage to the VSD Logic Board.
A Current transformer is included on each output phase
assembly to provide motor current information to the
VSD Logic Board.
ACCESSORIES AND OPTIONS
Sound Reduction Options
The standard chiller has fans that operate at normal
speed, no compressor enclosure, and is typically used
in non-sensitive sound areas such as industrial areas or
locations with loud traffic background noise. One or
more of the following sound reduction options may be
employed by the system designer as normally generated machine noise is considered in the overall project
design.
Ultra Quiet Fans
With this option, the basic chiller is equipped with specially designed fans and motors to provide lower sound
levels and retain appropriate airflow. The result is reduced fan generated noise with minimal effect on the
chiller capacity or efficiency at standard AHRI conditions. (Factory-mounted)
Two-Speed Fans
With this option, the basic chiller is equipped with fans
designed with two operating speeds. At high ambient
conditions the fans operate at the normal speed with
sound levels equivalent to Ultra Quiet Fans. As the ambient temperature falls, the fans automatically reduce
to slow speed reducing sound levels. If very low sound
is required at all ambient conditions normal fan speed
can be inhibited. (Factory-mounted)

The VSD is cooled by a propylene glycol cooling loop.


The loop utilizes a glycol pump, which pumps glycol
through the VSD heatsinks to cool the power components. The glycol is then circulated through the condenser to reject the heat from the VSD. The cooled
glycol is then circulated back through the loop.

Reduced Sound Option

Various ancillary sensors and boards are used to send


information back to the VSD Logic Board. Each IGBT
Power Module within the DC to AC inverter section
contains a thermistor heatsink temperature sensor to
provide temperature information to the VSD Logic
Board. The Bus Isolator board utilizes three resistors

This option is only available with the selection of Ultra


Quiet Fans or Two-Speed Fans. The chiller is equipped
with an acoustically lined compressor enclosure. This
option is typically for locations near residential areas,
hotels, or hospitals etc., where background noise is
limited. When paired with the Two-Speed Fan option

32

With this option the chiller is equipped with an unlined


compressor enclosure. This option is typically used for
daytime operation where background noise is lower
than normal city traffic etc. (Factory-mounted)
Low Sound Option

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

the unit can operate at normal speed during the day,


when background noise levels are noticeable, and at
low speed in the evening and at night when background
levels are lower. (Factory-mounted)
SilentNight
Standard variable speed compressors result in a chiller
system that has lower part load sound values than conventional air-cooled chillers. Over 99% of chiller operating hours occur when building loads are less than
design and/or ambient temperatures are less than design. As a result, all YCIV model chillers will operate
with less than full load sound output nearly all the time.
This is especially important on evenings and weekends
when neighbors are home the most. Due to time of day
based sound regulations it may be desirable to force
the chiller to a lower sound level on demand. The SilentNight control option provides a control input to
limit sound output of the chiller based on time of day.
This feature is programmable at the chiller panel or can
be controlled remotely via signal (4 to 20mA or 0 to10
VDC) from a BAS system.

Pre-Coated Fin Condenser Coils


The air-cooled condenser coils are constructed of epoxy-coated aluminum fins. This can provide corrosion
resistance comparable to copper-fin coils in typical
seashore locations. Either these or the post coated coils
(below), are recommended for units being installed at
the seashore or where salt spray may hit the unit.
Post-Coated Epoxy Dipped Condenser Coils
The unit is built with dipped-cured epoxy condenser
coils. This is another choice for seashore and other corrosive applications (with the exception of strong alkalis, oxidizers and wet bromine, chlorine and fluorine in
concentrations greater than 100 ppm).
Copper Fin Condenser Coils
The unit constructed with copper tube condenser coils,
which have copper fins. (This is not recommended
for units in areas where they may be exposed to acid
rain.)
Protective Chiller Panels

High Static Fans - (400V/50Hz and 380V/60Hz)

Wire Panels (Full Unit)

Condenser fans with higher power motors suitable for


high external static pressure, up to 100Pa (0.4 in. water), across condenser coils. Select this option if additional air-flow resistance may be present due to flow
restrictions such as field installed ducts, filters, soundenclosures etc. (Factory-mounted)

UV stabilized black polyvinyl chloride coated, heavy


gauge, welded wire mesh guards mounted on the exterior
of the unit. Protects condenser coil faces and prevents
unauthorized access to refrigerant components (compressors, pipes, cooler, etc.), yet provides free air flow. This
can cut installation cost by eliminating the need for separate, expensive fencing. (Factory-mounted)

High Airflow Fans - (400V/50Hz and 380V/60Hz)


Condenser fans with airfoil type blades and high power
motors providing extra airflow across coils. In some
chiller configurations, this option can provide an increase in chiller capacity. Contact your local Johnson
Controls representative for more information. (Factorymounted)
Condenser Coil Protection
Standard condenser coil construction materials include
aluminum fins, copper tubes, and galvanized tube supports for generally good corrosion resistance. However,
these materials are not adequate for all environments.
The system designer can take steps to inhibit coil corrosion in harsh applications and enhance equipment
life by choosing from these options based on project
design parameters and related environmental factors.
(Factory-mounted)

JOHNSON CONTROLS

Louvered Panels (Condenser Coils Only)


Louvered panels, painted the same color as the unit,
are mounted over the exterior condenser coil faces on
the sides of the unit to visually screen and protect coils.
(Factory-mounted)
Louvered Panels (Full Unit)
Louvered panels, painted the same color as the unit,
enclose the unit to protect condenser coils from incidental damage, visually screen internal components,
and prevent unauthorized access to internal components. (Factory-mounted)
Louvered (Condensers)/Wire Panels
(Mechanical)
Louvered panels, painted the same color as the unit,
are mounted on external condenser coil faces. Heavy
gauge, welded wire-mesh, coated to resist corrosion,
around base of machine to restrict unauthorized access.
(Factory-mounted)
33

PRODUCT DESCRIPTION
FORM 201.23-NM1 (910)

Evaporator Options

Chicago Code Relief Valve

Double Thick 1-1/2" Insulation

Special relief valves per Chicago code. (Factorymounted)

Double thickness insulation is provided. (Factorymounted)


Raised Face Flange Accessory
Used for cooler nozzles:
150 psig (10.3 barg), welded flanges (field kit,
matching pipe flange by contractor).
150 psig (10.3 barg) companion weld flanges (field
kit - not available with 460V units).
150 psig (10.3 barg), ANSI/AWWA C-606 couplings
(field kit, matching pipe flange by contractor).
Opposite Handed Evaporator Water
Connections
Easily installed standard water connections are on the
left-hand side of the unit, when viewed from the control panel end.
General Options
Flow Switch Accessory
Vapor proof SPDT, NEMA 3R switch, 150 psig (10.3
barg) DWP, 20F to 250F (-7C to 121C) with 1"
NPT (IPS) connection for upright mounting in horizontal pipe (This flow switch or equivalent must be
furnished with each unit). (Field-mounted).
Differential Pressure Switch
Alternative to the paddle-type flow switch. Range is 3
to 45 psig (0.2 to 3 barg) with 1/4" NPTE pressure connections. (Field-mounted)
Building Automation System Interface
Chiller will accept 4 to 20mA or 0 to 10 VDC input to
reset the leaving chilled liquid temperature. (Factorymounted)
Multi-Unit Sequence Control
Separate sequencing control center provided to permitting control of up to eight chillers in parallel based on
mixed liquid temperature (interconnecting wiring by
others). (Field-mounted)
Service Isolation Valve
Service suction isolation valve added to unit for each
refrigerant circuit. (Factory-mounted)

34

Pressure Relief (CE/PED) Service Valve Kit


Each relief valve is mounted on a sealable ball valve to
aid maintenance. (Factory-mounted)
Circuit Breaker
Power panel will come equipped with a factory mounted circuit breaker at the point of incoming single or
multi-point connections that provides the following:
A means to disconnect power mounted on chiller.
Circuit breaker(s) sized to provide the motor branch
circuit protection, short circuit protection and
ground fault protection for the motor branch-circuit
conductors, the motor control apparatus and the motors. (Chiller mounted circuit breaker option sized
for branch circuit protection eliminates the need
to provide a separate line of sight disconnect and
separate branch circuit protection device.)
A lockable operating handle that extends through
power panel door. This allows power to be disconnected without opening any panel doors.
A Short Circuit Withstand Rating of 65,000 amps
when the chiller electrical enclosure when using
circuit breaker option is 380, 400, and 460V. Rated
IAW UL508.
Vibration Isolation
Elastomeric Isolation
This option is recommended for normal installations. It
provides very good performance in most applications
for the least cost. (Field-mounted)
One Inch Spring Isolators
Spring and cage type isolators for mounting under
the unit base rails. They are level adjustable. Nominal
deflection is 1" and may vary slightly by application.
(Field-mounted)
Two Inch Seismic Spring Isolators
Restrained Spring-Flex Mounting isolators incorporate
a rugged welded steel housing with vertical and horizontal limit stops. Housings designed to withstand a
minimum 1.0g accelerated force in all directions up to
2" (51mm). The deflection may vary slightly by application. They are level adjustable. (Field-mounted)

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

UNIT MODEL NUMBER NOMENCLATURE

The model number denotes the following characteristics of the unit.

Y C I V - 0720 - S - A - 46 - V A A
DEVELOPMENT CODE

YORK

DESIGN SERIES

CHILLER
AIR-COOLED
VSD DRIVEN
SCREW COMPRESSOR
MODEL NUMBER

UNIT DESIGNATOR
E- High Efficiency with Standard IPLV
S- Standard Efficiency with Standard IPLV
P- Standard Efficiency with Optimized IPLV
V- High Efficiency with Optimized IPLV

JOHNSON CONTROLS

STARTER - VSD
VOLTAGE CODE
REFRIGERANT - R134a
UNIT DESIGNATOR

VOLTAGE CODE
17=200-3-60
28=230-3-60
40=380-3-60
46=460-3-60
50=380/400/415-3-50
58=575-3-60

35

PRODUCT DESCRIPTION
FORM 201.23-NM1 (910)

Complete pin number description


FEATURE

DESCRIPTION

OPTION

CONTRACT

Contract Number

NUM

Contract Number = {num}

ORDER

Order Quantity

QTY

Order quantity = {ord_qty}

USA

USA Origin

SHIP WT

Shipping Weight

N
Y
LBS
KG

USA origin not required


USA origin required
Crane/Rigging Shipping Weight = {lbs}
Crane/Rigging Shipping Weight = {kg}

MODEL

Model (PIN 1-4)

YCIV

YCIV

Nominal Capacity
(PIN 5-8)

0590
0630
0700
0760
0800
0830
0930
1050
1120
1180
1340
1500

0590
0630
0700
0760
0800
830
0930
1050
1120
1180
1340
1500

CAP

UNIT

Unit Designator (PIN 9)

REF.

Refrigerant (PIN 10)

VOLTS

Voltage (PIN 11, 12)

STARTER

Starter (PIN 13)

DESIGN

Design Series (PIN 14)


Modification Level
(PIN 15)

DEV

POWER

Power Fld (PIN 16, 17)

Standard Efficiency, Standard IPLV

Standard Efficiency, Optimized IPLV

High Efficiency/High Ambient Unit,


Standard IPLV

High Efficiency/High Ambient Unit,


Optimized IPLV

A
17
28
40
46
50
58
V

R-134a
200/3/60
230/3/60
380/3/60
460/3/60
380-415/3/50
575/3/60
Variable Speed Drive

Design Series A

Mod Level B

SX

SP Supply TB

BX

SP Circuit Breaker w/Lockable Handle

SS

SP Supply TB w/Ind. Sys. Disconnect Switches

CS
QQ
TRANS

Control Transformer
(PIN 18)

PFC

Convenience Outlet
(PIN 19)

AMB

36

PIN 20

DESCRIPTION

T
Q
X
O
Q
X
Q

SP Circuit Breaker w/Ind. Sys.


Disconnect Switches
Special Power Option
Control Transformer required
Special Transformer or Power Strip
required
No Option Required
Convenience Outlet, 115V GFI
(Customer Powered)
Special quote
No option required
Special quote

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Complete pin number description (CONT'D)


FEATURE

DESCRIPTION

BAS

BAS Interface (PIN 21)

LCD

LCD (PIN 22)

RDOUT

Silent Night (PIN 23)

SAFETY

Safety Code (PIN 24)

SENSOR

PIN 25

PUMP

Pump Control (PIN 26)

REMOTE

Remote Ctrl Panel


(PIN 27)

SEQ

Sequence Kit (PIN 28)

TEMP

Water Temp (PIN 29, 30)

CHICAGO

Chicago Code Kit


(PIN 31)

VALVES

Valves (PIN 32)

HGBP

PIN 33

GAUGE

PIN 34

OVERLOAD

PIN 35

PIN36

PIN 36

JOHNSON CONTROLS

OPTION
X
T
C
M
Q
X
S
F
G
I
P
Q
X
N
Q
L
C
Q
X
Q
X
Q
X
O
Q
X

DESCRIPTION
No BAS Reset/Offset required
BAS/EMS Temp Reset/Offset
BAS/EMS Current Reset/Offset
BAS/EMS Both Temp and Current
Reset/Offset
ISN Microgateway
Special BAS Reset/Offset required
English LCD & Keypad Display (std)
Spanish LCD & Keypad Display
French LCD & Keypad Display
German LCD & Keypad Display
Italian LCD & Keypad Display
Portuguese LCD & Keypad Display
Special LCD & Keypad Display
No option required
Silent Night sound limiting control option
Special quote
N. American Safety Code (cUL/cETL)
CE listing
Special Safety Code
No option required
Special quote
No Pump Control required
Special Pump Control required
No Remote Control Panel required
OptiView Remote Control Panel required
Special Remote Control Panel required
No Sequence Kit required

Sequence Control & Automatic Lead Transfer = {seq}

Special Sequence Kit required

NUM
QQ
X
C
S
B
P
D
R

Leaving Water Temp. = {temp} degrees


Special LWT requirements
No Chicago Code Kit required
Chicago Code Kit required
Service Isolation Valve
Both Isolation Valve and Chicago Code
Pressure Relief Service Valve Kit
Service Isolation & Pressure Relief Valve Kit
Dual Pressure Relief

Dual Pressure Relief & Suction Service


Isolation

Q
X
Q
X
Q

Special Chicago Code Kit required


Standard Valves required
Special Optional Valves required
No option required
Special quote

No option required

Special quote

X
Q
X
Q

No option required
Special quote
No option required
Special quote

37

PRODUCT DESCRIPTION
FORM 201.23-NM1 (910)

Complete pin number description (CONT'D)


FEATURE

DESCRIPTION

HTR

Crankcase Heater
(PIN 37)

DWP

DWP (PIN 38)

INS

Insulation (PIN 39)

FLANGES

Flanges (PIN 40)

FLOW

Flow Switch (PIN 41)

OPTION
H
Q
X
3
Q
X
D
Q
X
W
V
M
F
Q
X
S
T
U
D
E
Q
A
E
Q
X
R
Q
L
R
Q
A
C
B
P
E
Q

150 PSIG DWP


300 PSIG DWP
Special DWP
3/4 Cooler Insulation
1-1/2" Cooler Insulation
Special Cooler Insulation
No Flanges required
Weld Flange Kit required
Victaulic Flange Kit required
Weld Flange with Mating Flange
Victaulic Flange with Welded Mating Flange
Special Flanges required
No Flow Switch required
One Flow Switch required
Two Flow Switches required
Three Flow Switches required
One Differential Pressure Switch required
Two Differential Pressure Switches required
Three Differential Pressure Switches
required
Special Switch required
ASME Pressure Vessel Codes
PED Pressure Vessel Code
Special Pressure Vessel Codes
Standard Cooler
Remote Cooler
Special Cooler requirements
Handed cooler left, view from control panel end
Handed cooler right, view from control panel end
Special quote
Aluminum Coils
Copper Fin Coils
Pre-Coated Fin Coils
Post-Coated Dipped Coils
Pre-coated Epoxy Non-slit ripple fins
Special Coils

Partial Heat Recovery not required

H
D
Q
X
Q
X
1
2
3
4
5
6
7
8
Q

Partial Heat Recovery required


Desuperheater
Special quote
TEAO Fan Motors
Special Fan Motors
No Enclosure Panels required
Wire (Full Unit) Encl Panels (factory)
Wire (Full Unit) Encl Panels (field)
Wire/Louvered Encl Panels (factory)
Wire/Louvered Encl Panels (field)
Louvered (cond only) Encl Panels (factory)
Louvered (cond only) Encl Panels (field)
Louvered (full unit) Encl Panels (factory)
Louvered (full unit) Encl Panels (field)
Special Enclosure Panels required

38

VESSEL

Vessel Codes (PIN 42)

CLR

Cooler (PIN 43)

PIN44

Connections (PIN 44)

COILS

Coils (PIN 45)

HEAT

Heat Recovery (PIN 46)

FANMOTORS

Fan Motors (PIN 47)

PANEL

Enclosure Panels
(PIN 48)

DESCRIPTION
Compressor Crankcase Heaters
Special quote

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Complete pin number description (CONT'D)


FEATURE

ACOUSTIC

PIN 50
PIN 51

DESCRIPTION

Acoustical arrgt (PIN 49)

PIN 50
PIN 51

FANS

Fans (PIN 52)

PAINT

Overspray Paint
(PIN 53)

OPTION

DESCRIPTION

No Sound Enclosure required

Reduced Noise

Low Noise

Special Sound Enclosure required

No option required

Special quote

No option required

Special quote

Standard Low Sound Fans

Ultra Quiet Fans

High Static Fans

Special Sound Fans

No Final Overspray Paint required

Special Final Overspray Paint required

X
1
S
N
Q

No Vibration Isolators required


1" Deflection Isolators required
Seismic Isolators required
Neoprene Pad Isolators required
Special Vibration Isolators required

ISOL

Isolators (PIN 54)

WARRANTY

Warranty (PIN 55)

For Marketing Purposes

REFRIGERANT WTY

Refrigerant Wty
(PIN 56)

For Marketing Purposes

SHIP

Ship Instructions
(PIN 57)

X
A
C
B
P
Q

PIN58

PIN 58

PIN59

PIN 59

PIN60

PIN 60

MFG

Plant of Mfg (PIN 61)

LOC

Mfg Location

YW

YorkWorks Version

SQ

Special Quote

JOHNSON CONTROLS

X
Q
X
Q
R
MEX
SAT
CV
UV
Q

No option required
Buy American Act Compliance
Container Shipping Kit
Both Buy American Act Compliance and Container Shipping Kit
Container Shipment Ready, Loading to be Arranged by CSR
Special quote
For Marketing Purposes
No option required
Special quote
No option required
Special quote
Plant of Manufacture - Monterrey
Monterrey
San Antonio
YorkWorks configuration version {cv}
YorkWorks upload version {uv}
Special quote

39

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

40

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SECTION 3 - Handling and storage


DELIVERY AND STORAGE
To ensure consistent quality and maximum reliability,
all units are tested and inspected before leaving the factory. Units are shipped completely assembled and containing refrigerant under pressure. Units are shipped
without export crating unless crating has been specified on the Sales Order.
If the unit is to be put into storage, prior to installation,
the following precautions should be observed:
The chiller must be blocked so that the base is not
permitted to sag or bow.
Ensure that all openings, such as water connections,
are securely capped.
Do not store where exposed to ambient air temperatures exceeding 110F (43C).
The condensers should be covered to protect the fins
from potential damage and corrosion, particularly
where building work is in progress.
The unit should be stored in a location where there
is minimal activity in order to limit the risk of accidental physical damage.
To prevent inadvertent operation of the pressure
relief devices the unit must not be steam cleaned.
It is recommended that the unit is periodically inspected during storage.

The units are designed to be lifted using cables. A


spreader bar or frame should be used in order to prevent damage to the unit from the lifting chains (see
Pages 42 and 43).
Units are provided with lifting eyes in the sides of the
base frame, which can be attached to directly using
shackles or safety hooks (see Pages 42 and 43).

The unit must only be lifted by the


base frame at the points provided.
Never move the unit on rollers, or lift
the unit using a forklift truck.
Care should be taken to avoid damaging the condenser
cooling fins when moving the unit.
Lifting Weights
For details of weights and weight distribution, refer to
the data shipped in the chiller information packet and
unit nameplate.

INSPECTION
Remove any transit packing and inspect the unit to ensure that all components have been delivered and that
no damage has occurred during transit. If any damage
is evident, it should be noted on the carriers freight bill
and a claim entered in accordance with the instructions
given on the advice note.
Major damage must be reported immediately to your
local Johnson Controls representative.
MOVING THE CHILLER
Prior to moving the unit, ensure that the installation site
is suitable for installing the unit and is easily capable
of supporting the weight of the unit and all associated
services.

JOHNSON CONTROLS

41

HANDLING AND STORAGE

FORM 201.23-NM1 (910)

Unit Rigging

#4

#3
#2
Z
Y

LD13125

#5

#1

#4

2 COMPRESSOR

LD13126

#3
#2
Z
Y

3 COMPRESSOR

#1

LIFT POINTS DIMENSIONS TAKEN FROM


(NOT ALL POINTS ON UNITS)
2 COMPRESSOR MODELS
50 hz

eFFICIENCY

0590

HIGH

#1
INCH
Y = 33.3

#2
METRIC
Y = 846

INCH
Y = 136.7

#3
METRIC
Y = 3473

#4

INCH
Y = 216.7

METRIC
Y = 5505

INCH
---

#5
METRIC
---

INCH
---

METRIC
---

0600

STD

Y = 33.3

Y = 846

Y = 136.7

Y = 3473

Y = 216.7

Y = 5505

---

---

---

---

0630

HIGH

Y = 33.3

Y = 846

Y = 136.7

Y = 3473

Y = 224.7

Y = 5708

---

---

---

---

0650

STD

Y = 33.3

Y = 846

Y = 136.7

Y = 3473

Y = 216.7

Y = 5505

---

---

---

---

0700

HIGH

Y = 33.3

Y = 846

Y = 136.7

Y = 3473

Y = 224.7

Y = 5708

---

---

---

---

0720

STD

Y = 33.3

Y = 846

Y = 136.7

Y = 3473

Y = 224.7

Y = 5708

---

---

---

---

0760

HIGH

Y = 33.3

Y = 846

Y = 136.7

Y = 3473

Y = 224.7

Y = 5708

---

---

---

---

0770

STD

Y = 33.3

Y = 846

Y = 136.7

Y = 3473

Y = 224.7

Y = 5708

---

---

---

---

0800

HIGH

Y = 33.3

Y = 846

Y = 92.7

Y = 2355

Y = 180.7

Y = 4590

Y = 284.9

Y = 7235

---

---

Y = 7235

0830

HIGH

Y = 33.3

Y = 846

Y = 92.7

Y = 2355

Y = 180.7

Y = 4590

Y = 284.9

0840

STD

Y = 33.3

Y = 846

Y = 136.7

Y = 3473

Y = 224.7

Y = 5708

---

---

---

---

0920

STD

Y = 33.3

Y = 846

Y = 92.7

Y = 2355

Y = 180.7

Y = 4590

Y = 284.9

Y = 7235

---

---

0930

HIGH

Y = 33.3

Y = 846

Y = 92.7

Y = 2355

Y = 180.7

Y = 4590

Y = 284.9

Y = 7235

---

---

1000

STD

Y = 33.3

Y = 846

Y = 92.7

Y = 2355

Y = 180.7

Y = 4590

Y = 284.9

Y = 7235

---

---

METRIC
Y = 6061.3

INCH
Y = 357

METRIC
Y = 9067.4

INCH
---

3 COMPRESSOR MODELS

42

50 hz

eFFICIENCY

1050

HIGH

#1
INCH
Y = 33.2

#2
METRIC
Y = 843.8

INCH
Y = 141.1

#3
METRIC
Y = 3584.8

INCH
Y = 238.6

#4

#5
METRIC
---

1070

STD

Y = 33.2

Y = 843.8

Y = 141.1

Y = 3584.8

Y = 238.6

Y = 6061.3

Y = 357

Y = 9067.4

---

---

1120

HIGH

Y = 33.2

Y = 843.8

Y = 123.7

Y = 3142.2

Y = 216.7

Y = 5504.2

Y = 320.5

Y = 8139.9

Y = 401

Y = 10185

1180

STD

Y = 33.2

Y = 843.8

Y = 141.8

Y = 3584.8

Y = 238.6

Y = 6061.3

Y = 357

Y = 9067.4

---

---

1220

HIGH

Y = 33.2

Y = 843.8

Y = 120.7

Y = 3064.9

Y = 216.7

Y = 5504.2

Y = 320.5

Y = 8139.9

Y = 401

Y = 10185

1340

STD

Y = 33.2

Y = 843.8

Y = 120.7

Y = 3064.9

Y = 216.7

Y = 5504.2

Y = 320.5

Y = 8139.9

Y = 401

Y = 10185

1380

HIGH

Y = 33.2

Y = 843.8

Y = 120.7

Y = 3064.9

Y = 217.8

Y = 5531.5

Y = 328.1

Y = 8334.6

Y = 445

Y = 11302.6

1500

STD

Y = 33.2

Y = 843.8

Y = 120.7

Y = 3064.9

Y = 217.8

Y = 5531.5

Y = 328.1

Y = 8334.6

Y = 445

Y = 11302.6

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Lifting hooks should be inserted into the holes provided in the bottom of the frame rail.
Use spreader bars to avoid lifting chains hitting the
chiller. Various methods of spreader bar arrangements
may be used; keeping in mind the intent is to keep the
unit stable and to keep the chains from hitting the chiller and causing damage.

LD10483

Use spreader bars to avoid lifting chains hitting the


chiller.

Never lift the chiller using a forklift


or by hooking to the top rails. Use
only the lifting holes provided.

Lifting Instructions are placed on a label on the chiller


and on the shipping bag.

LD10484

JOHNSON CONTROLS

43

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

44

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LOCATION REQUIREMENTS

SECTION 4 - installation

To achieve optimum performance and trouble-free


service, it is essential that the proposed installation
site meets the location and space requirements for the
model being installed. For dimensions, refer to Section
6 Technical Data in this IOM.
It is important to ensure that the minimum service access space is maintained for cleaning and maintenance
purposes.
OUTDOOR INSTALLATIONS
The units can be installed at ground level on a suitable
flat level foundation easily capable of supporting the
weight of the unit, or on a suitable rooftop location. In
both cases an adequate supply of air is required. Avoid
locations where the sound output and air discharge
from the unit may be objectionable.
The location should be selected for minimum sun exposure and away from boiler flues and other sources
of airborne chemicals that could attack the condenser
coils and steel parts of the unit.
If located in an area accessible to unauthorized persons, steps must be taken to prevent access to the unit
by means of a protective fence. This will help to prevent the possibility of vandalism, accidental damage,
or possible harm caused by unauthorized removal of
protective guards or opening panels to expose rotating
or high voltage components.
For ground level locations, the unit must be installed
on a suitable flat and level concrete base that extends
to fully support the two side channels of the unit base
frame. A one-piece concrete slab, with footings extending below the frost line is recommended. To avoid
noise and vibration transmission, the unit should not
be secured to the building foundation.
On rooftop locations, choose a place with adequate
structural strength to safely support the entire operating weight of the unit and service personnel. The unit
can be mounted on a concrete slab, similar to ground
floor locations, or on steel channels of suitable strength.
The channels should be spaced with the same centers
as the unit side and front base rails. This will allow
vibration isolators to be fitted if required. Isolators are
recommended for rooftop locations.

JOHNSON CONTROLS

Any ductwork or attenuators fitted to the unit must not


have a total static pressure resistance, at full unit airflow, exceeding the capability of the fans installed in
the unit.
INDOOR INSTALLATIONS
The unit can be installed in an enclosed plant room,
provided the floor is level and of suitable strength to
support the full operating weight of the unit. It is essential that there is adequate clearance for airflow to
the unit. The discharge air from the top of the unit must
be ducted away to prevent re-circulation of air within
the plant room. If common ducts are used for fans,
non-return dampers must be fitted to the outlet from
each fan.
The discharge ducting must be properly sized with a
total static pressure loss, together with any intake static
pressure loss, less than the available static pressure capability for the type of fan fitted.
The discharge air duct usually rejects outside the building through a louver. The outlet must be positioned to
prevent the air being drawn directly back into the air
intake for the condenser coils; as such re-circulation
will affect unit performance.
LOCATION CLEARANCES
Adequate clearances around the unit(s) are required for
the unrestricted airflow for the air-cooled condenser
coils and to prevent re-circulation of warm discharge
air back onto the coils. If clearances given are not
maintained, airflow restriction or re-circulation will
cause a loss of unit performance, an increase in power
consumption, and may cause the unit to malfunction.
Consideration should also be given to the possibility of
down drafts, caused by adjacent buildings, which may
cause re-circulation or uneven unit airflow.
For locations where significant cross winds are expected, such as exposed roof tops, an enclosure of solid
or louver type is recommended to prevent wind turbulence interfering with the unit airflow.
When units are installed in an enclosure, the enclosure
height should not exceed the height of the unit on more
than one side. If the enclosure is of louvered construction, the same requirement of static pressure loss applies as for ducts and attenuators stated above.
45

INSTALLATION
Where accumulation of snow is likely, additional height
must be provided under the unit to ensure normal airflow to the unit

Clearance dimensions provided elsewhere are necessary to maintain good


airflow and ensure correct unit operation. It is also necessary to consider
access requirements for safe operation
and maintenance of the unit and
power and control panels. Local
health and safety regulations, or practical considerations for service replacement of large components, may
require larger clearances than those
given in the Technical Data section
(Page 146).
VIBRATION ISOLATORS
Optional sets of vibration isolators can be supplied
loose with each unit.
Using the Isolator tables shipped with the unit in the
information pack, refer to the Dimension section
(pages 126 through 145), Isolator Selection and
Mounting section (pages 147 through 162) and Isolator Types (pages 164 through 169 for units shipped
on or after June 15, 2008 and Pages 170 through 174
for units shipped before June 15, 2008). Identify each
mount and its correct location on the unit.
Installation
Place each mount in its correct position and lower the
unit carefully onto the mounts ensuring the mount engages in the mounting holes in the unit base frame.

FORM 201.23-NM1 (910)

SHIPPING BRACES
The chillers modular design does not require shipping
braces.
CHILLED LIQUID PIPING
General Requirements
The following piping recommendations are intended to
ensure satisfactory operation of the unit(s). Failure to
follow these recommendations could cause damage to
the unit, or loss of performance, and may invalidate the
warranty.

The maximum flow rate and pressure


drop for the cooler must not be exceeded at any time. Refer to the Technical Data section for details.
The liquid must enter the cooler at the
inlet connection. The inlet connection
for the cooler is at the control panel
end of the cooler.
A flow switch must be installed in the customer piping at the outlet of the cooler and wired back to the
control panel using shielded cable.
There should be a straight run of piping of at least 5
pipe diameters on either side. The flow switch should
be wired to Terminals 2 and 13 on the 1TB terminal
block (See FIG. 31 and 32, Pages 185 and 186). A
flow switch is required to prevent damage to the cooler
caused by the unit operating without adequate liquid
flow.

On adjustable mounts, transfer the unit weight evenly


to the springs by turning the mount adjusting nuts (located just below the top plate of the mount) counterclockwise to raise and clockwise to lower. This should
be done two turns at a time until the top plates of all
mounts are between 1/4" and 1/2" (6 and 12 mm) clear
of top of their housing and the unit base is level.

The flow switch used must have gold plated contacts


for low voltage/current operation. Paddle type flow
switches suitable for 150 PSIG (10 bar) working pressure and having a 1" N.P.T. connection can be obtained
from YORK as an accessory for the unit. Alternatively,
a differential pressure switch fitted across an orifice
plate may be used, preferably of the high/low limit
type.

A more detailed installation instruction is provided on Pages 164 through


169 for units shipped on or after June
15, 2008 and Pages 170 through 174
for units shipped before June 15,
2008.

The chilled liquid pump(s) installed in the piping


system(s) should discharge directly into the unit cooler
section of the system. The pump(s) may be controlled
by the chiller controls or external to the unit. For details, refer to Electrical Elementary and Connection
Diagrams.

46

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Pipework and fittings must be separately supported to


prevent any loading on the cooler. Flexible connections
are recommended which will also minimize transmission of vibrations to the building. Flexible connections
must be used if the unit is mounted on anti-vibration
mounts, as some movement of the unit can be expected
in normal operation.
Piping and fittings immediately next to the cooler
should be readily de-mountable to enable cleaning before operation, and to facilitate visual inspection of the
exchanger nozzles.
The cooler must be protected by a strainer, preferably of 40 mesh, fitted as close as possible to the liquid inlet connection, and provided with a means of
local isolation.
The cooler must not be exposed to flushing velocities
or debris released during flushing. It is recommended
that a suitably sized bypass and valve arrangement is
installed to allow flushing of the piping system. The
bypass can be used during maintenance to isolate the
heat exchanger without disrupting flow to other units.
Thermometer and pressure gauge connections should
be provided on the inlet and outlet connections of each
cooler. Gauges and thermometers are not provided
with the unit.
Drain and air vent connections should be provided at
all low and high points in the piping to permit drainage
of the system and to vent any air in the pipes.
Liquid system lines at risk of freezing, due to low ambient temperatures should be protected using insulation and heater tape and/or a suitable glycol solution.
The liquid pump(s) may also be used to ensure liquid
is circulated when the ambient temperature approaches
freezing point.
Insulation should also be installed around the cooler
nozzles. Heater tape of 21 Watts per meter under the insulation is recommended, supplied independently and
controlled by an ambient temperature thermostat set to
switch ON at approximately 4F, above the freezing
temperature of the chilled liquid.

JOHNSON CONTROLS

The cooler is protected by heater mats placed under


the insulation, which are powered from the unit control system power supply. During cold weather when
there is a risk of freezing, chiller power should be left
switched on to provide the freeze protection function
unless the liquid systems have been drained.

Any debris left in the water piping


between the strainer and cooler could
cause serious damage to the tubes in
the cooler and must be avoided. Be
sure the piping is clean before connecting it to the evaporator. Keep
evaporator nozzles and chilled liquid
piping capped prior to installation to
assure construction debris is not allowed to enter.
The installer/user must also ensure
that the quality of the water in circulation is adequate, without any dissolved
gases, which can cause oxidation of
steel parts within the cooler.
WATER TREATMENT
The unit performance provided in the Design Guide
is based on a fouling factor of 0.0001 ft2hrF/Btu
(0.018m2/hr C/kW). Dirt, scale, grease and certain
types of water treatment will adversely affect the heat
exchanger surfaces and therefore the unit performance.
Foreign matter in the water system(s) can increase the
heat exchanger pressure drop, reducing the flow rate
and causing potential damage to the heat exchanger
tubes.
Aerated, brackish or salt water is not recommended for
use in the water system(s). Johnson Controls recommends that a water treatment specialist should be consulted to determine whether the proposed water composition will adversely affect the evaporator materials
of carbon steel and copper. The pH value of the water
flowing through the evaporator must be kept in a range
between 7 and 8.5.

47

INSTALLATION

FORM 201.23-NM1 (910)

PIPEWORK ARRANGEMENT

Option Flanges

The following is a suggested piping arrangement for


single unit installations. For multiple unit installations,
each unit should be piped as shown in FIG. 3.

One of two types of flanges may be fitted depending


on the customer or local Pressure Vessel Code requirements. These are Victaulic-Adapter flanges, normally
supplied loose, or weld flanges, which may be supplied loose or ready-fitted. Victaulic-Adapter and weld
flange dimensions are to ISO 7005 - NP10.

-Isolating Valve - Normally Open


-Isolating Valve - Normally Closed
-Flow Regulating Valve
-Flow Measurement Device
-Strainer
-Pressure Tapping
-Flow Switch
-Flanged Connection
-Pipework

WELD FLANGE

LD10495

FIG. 5 - flange attachment


LD10507

REFRIGERANT RELIEF VALVE PIPING


The evaporator is protected against internal refrigerant
overpressure by refrigerant relief valves. A pressure relief valve is mounted on each of the main refrigerant
lines connecting the cooler to the compressors.

FIG. 3 - PIPEWORK ARRANGEMENT

CONNECTION TYPES and SIZES


For connection sizes relevant to individual models refer to the Technical Data section.
COOLER CONNECTIONS
Standard chilled liquid connections on all coolers are
of the Victaulic Groove type (See FIG. 4).

A piece of pipe is fitted to each valve and directed so


that when the valve is activated the release of high
pressure gas and liquid cannot be a danger or cause
injury. For indoor installations, pressure relief valves
should be piped to the exterior of the building.
The size of any piping attached to a relief valve must
be of sufficient diameter so as not to cause resistance to
the operation of the valve. Unless otherwise specified
by local regulations. Internal diameter depends on the
length of pipe required and is given by the following
formula:


LD10494

FIG. 4 - victaulic groove

VICTAULIC

D5 = 1.447 x L

Where:
D = minimum pipe internal diameter in cm
L = length of pipe in meters
If relief piping is common to more than one valve, its
cross-sectional area must be at least the total required
by each valve. Valve types should not be mixed on a
common pipe. Precautions should be taken to ensure
the outlets of relief valves or relief valve vent pipes
remain clear of obstructions at all times.

48

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

DUCTWORK CONNECTION
General Requirements
The following ductwork recommendations are intended to ensure satisfactory operation of the unit. Failure
to follow these recommendations could cause damage
to the unit, or loss of performance, and may invalidate
the warranty.
When ducting is to be fitted to the fan discharge it is
recommended that the duct should be the same crosssectional area as the fan outlet and straight for at least
three feet (1 meter) to obtain static regain from the fan.
Ductwork should be suspended with flexible hangers
to prevent noise and vibration being transmitted to
the structure. A flexible joint is also recommended between the duct attached to the fan and the next section
for the same reason. Flexible connectors should not be
allowed to concertina.
The unit is not designed to take structural loading. No
significant amount of weight should be allowed to rest
on the fan outlet flange, deck assemblies or condenser
coil module. No more than 3 feet (1 meter) of light
construction ductwork should be supported by the unit.
Where cross winds may occur, any ductwork must be
supported to prevent side loading on the unit.

ELECTRICAL CONNECTION
The following connection recommendations are intended to ensure safe and satisfactory operation of the
unit. Failure to follow these recommendations could
cause harm to persons, or damage to the unit, and may
invalidate the warranty.

No additional controls (relays, etc.)


should be mounted in the control
panel. Power and control wiring not
connected to the control panel should
not be run through the control panel.
If these precautions are not followed
it could lead to a risk of electrocution.
In addition, electrical noise could
cause malfunctions or damage the
unit and its controls.
After power wiring connection, do not
switch on mains power to the unit.
Some internal components are live
when the mains are switched on and
this must only be done by Authorized persons familiar with starting,
operating, and troubleshooting this
type of equipment.

If the ducts from two or more fans are to be combined


into a common duct, back-flow dampers should be fitted in the individual fan ducts. This will prevent recirculation of air when only one of the fans is running.
Units are supplied with outlet guards for safety and to
prevent damage to the fan blades. If these guards are
removed to fit ductwork, adequate alternative precautions must be taken to ensure persons cannot be harmed
or put at risk from rotating fan blades.

JOHNSON CONTROLS

49

INSTALLATION

FORM 201.23-NM1 (910)

POWER WIRING

115VAC CONTROL SUPPLY TRANSFORMER

All electrical wiring should be carried out in accordance


with local regulations. Route properly sized cables to
cable entries on the unit.

A 3-wire high voltage to 115VAC supply transformer


is standard in the chiller. This transformer is mounted
in the cabinet and steps down the high voltage supply
to 115VAC to be used by the controls, VSD, Feed and
Drain Valve Controller, valves, solenoids, heaters, etc.

In accordance with local codes, NEC codes and U.L.


Standards, it is the responsibility of the user to install
over current protection devices between the supply conductors and the power supply terminals on the unit.
To ensure that no eddy currents are set up in the power
panel, the cables forming the 3-phase power supply
must enter via the same cable entry.

All sources of supply to the unit must


be taken via a common point of isolation (not supplied by Johnson Controls).

Copper power wiring only should be used for supplying power to the chiller. This is recommended to avoid
safety and reliability issues resulting from connection
failure at the power connections to the chiller. Aluminum wiring is not recommended due to thermal characteristics that may cause loose terminations resulting from the contraction and expansion of the wiring.
Aluminum oxide may also build up at the termination
causing hot spots and eventual failure. If aluminum
wiring is used to supply power to the chiller, AL-CU
compression fittings should be used to transition from
aluminum to copper. This transition should be done in
an external box separate to the power panel. Copper
conductors can then be run from the box to the chiller.
POWER SUPPLY WIRING
Units require only one 3-phase supply, plus earth
ground.

The high voltage for the transformer primary is taken


from the chiller input. Fusing is provided for the transformer.

Removing high voltage power to the


chiller will remove the 115VAC supply
voltage to the control panel circuitry
and the evaporator heater. In cold
weather, this could cause serious damage to the chiller due to evaporator
freeze-up. Do not remove power unless alternate means are taken to ensure operation of the evaporator
heater.
CONTROL PANEL WIRING
All control wiring utilizing contact closures to the control panel terminal block is nominal 115VAC and must
be run in shielded cable, with the shield grounded at
the panel end only, and run in water tight conduit. Run
shielded cable separately from mains cable to avoid
electrical noise pick-up. Use the control panel cable
entry to avoid the power cables.
Voltage free contacts connected to the panel must be
suitable for 115VAC-10ma (gold contacts recommended). If the voltage free contacts form part of a relay or
contactor, the coil of the device must be suppressed using a standard R/C suppressor. The above precautions
must be taken to avoid electrical noise, which could
cause a malfunction or damage to the unit and its controls.

Connect the 3-phase supplies to the terminal block or


optional circuit breaker located in the panel using lug
sizes detailed in the Technical Data section (see Figures. 25, 31 and 32.
Connect a ground wire from the chiller panel ground
lug to the incoming line supply ground.

50

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

VOLTS FREE CONTACTS


Voltage free contacts are rated at 115VAC, 100VA resistive load only. Inductive loads must be suppressed
across the coil.
Chilled Liquid Pump Starter
Terminals 23 and 24 on 1TB (FIG. 31 and FIG. 32)
close to start the chilled liquid pump. This contact can
be used as a master start/stop for the pump in conjunction with the daily start/stop schedule.
Run Contact
Terminals 21 and 22 on 1TB (FIG. 31 and FIG. 32)
close to indicate that a system is running.
Alarm Contacts
The Systems 1/3 and 2/4 each have a single voltagefree contact, which will operate to signal an alarm
condition whenever any system locks out, or there is a
power failure. To obtain system alarm signal, connect
the alarm circuit to volt free Terminals 25 and 26 (Sys
1/3), Terminals 27 and 28 (Sys 2/4) of 1TB (FIG. 31
and FIG. 32).
SYSTEM INPUTS
Flow Switch
A chilled liquid flow switch of suitable type MUST be
connected between Terminals 2 and 13 of 1TB (FIG.
31 and FIG. 32) to provide protection against loss of
liquid flow, which will cause evaporator freeze-up if
the chiller is permitted to run. The flow switch circuitry
is a 115VAC circuit. Contacts must be rated for low
current (10ma). Gold contacts should be used.
Remote Run / Stop
A Remote Run/Stop input is available for each pair of
systems (1/3 and 2/4). These inputs require a dry contact to start and stop the system. System 1/3 remote

JOHNSON CONTROLS

dry contacts are connected between Terminals 2 and


15 of 1TB (FIG. 31 and FIG. 32) and System 2/4 dry
contacts are connected between Terminals 2 and 16 of
1TB (FIG. 31 and FIG. 32). If remote start/stop is not
utilized, a jumper must be paced across the terminals to
allow the system to run. The remote run/stop circuitry
is a 115VAC circuit. Contacts must be rated for low
current (10ma). Gold contacts should be used.
Remote Print
Closure of suitable contacts connected to Terminals 2
and 14 of 1TB (FIG. 31 and FIG. 32) will cause a hard
copy printout of Operating Data/Fault History to be
made if an optional printer is connected to the RS-232
port. The remote print circuitry is a 115VAC circuit.
Contacts must be rated for low current (10ma). Gold
contacts should be used.
Optional Remote Setpoint Offset
Temperature
A current or voltage signal connected to Terminals
17 and 18 will provide a remote offset function of the
chilled liquid setpoint, if required. See FIG. 31 and
FIG. 32 for the input location and Page 228 for a description of the option.
Optional Remote Setpoint Offset Current
A current or voltage signal connected to Terminals 19
and 20 will provide remote setting of the current limit
setpoint, if required. See FIG. 31 and FIG. 32 for the
input location and Page 230 for a description of the
option.
Optional Remote Setpoint Offset Sound
Limiting
A current or voltage signal connected to Terminals
40 and 41will provide remote setting of sound limit
setpoint, if required. See FIG. 31 and FIG. 32 for the
input location and Page 231 for a description of the
option.

51

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

52

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SECTION 5 - Commissioning
PREPARATION

Commissioning of this unit should


only be carried out by Johnson Controls Authorized personnel.

Commissioning personnel should be thoroughly familiar with the information contained in this document before starting the unit.
Commission the unit using the detailed checks outlined
in the Equipment Pre Start-up and Start-up Checklist
on Page 56.
PREPARATION GENERAL
The following basic checks should be made with the
customer power to the unit switched OFF.

Proper electrical lock out and tag


procedures must be followed.

Inspection
Inspect unit for installation damage. If found, take action and/or repair as appropriate.
Refrigerant Charge
Packaged units are normally shipped as standard with
a full refrigerant operating charge. Check that refrigerant pressure is present in both systems and that no
leaks are apparent. If no pressure is present, a leak test
must be undertaken, the leak(s) located and repaired.
Remote systems and units are supplied with a nitrogen
holding charge. These systems must be evacuated with
a suitable vacuum pump/recovery unit as appropriate
to below 500 microns.
Do not liquid charge with static water in the cooler.
Care must also be taken to liquid charge slowly to
avoid excessive thermal stress at the charging point.
Once the vacuum is broken, charge into the condenser coils with the full operating charge as given in the
Technical Data section.

JOHNSON CONTROLS

Service and Oil Line Valves


Open each compressor suction, economizer, and discharge service valve. If valves are of the back-seat type,
open them fully (counterclockwise) then close one turn
of the stem to ensure operating pressure is fed to pressure transducers. Open the liquid line service valve and
oil return line ball valve fully in each system.
Compressor Oil
To add oil to a circuit - connect a YORK hand oil pump
(Part No. 470-10654-000) to the 1/4" oil charging valve
on the oil separator piping with a length of clean hose
or copper line, but do not tighten the flare nut. Using
clean oil of the correct type (L oil), pump oil until all air has been purged from the hose then tighten
the nut. Stroke the oil pump to add oil to the oil system. The oil level should be between the middle of the
lower and middle of the upper sight glasses of the oil
separator. Approximately 4 to 5 gallons are present in
each refrigerant system, with typically 1 to 2 gallons
in each oil separator. Oil levels in the oil separators
above the top sight glass in either oil separator should
be avoided and may cause excessive oil carryover in
the system. High oil concentration in the system may
cause nuisance trips resulting from incorrect readings
on the level sensor and temperature sensors. Temperature sensor errors may result in poor liquid control and
resultant liquid overfeed and subsequent damage to the
compressor.
Fans
Check that all fans are free to rotate and are not damaged. Ensure blades are at the same height when rotated. Ensure fan guards are securely fixed.
Isolation / Protection
Verify all sources of electrical supply to the unit are
taken from a single point of isolation. Check that the
maximum recommended fuse sizes given in the Technical Data section has not been exceeded.
Control Panel
Check the panel to see that it is free of foreign materials (wire, metal chips, etc.) and clean out if required.
Power Connections
Check that the customer power cables are connected
correctly to the terminal blocks or optional circuit
breaker. Ensure that connections of power cables within the panels to the circuit breaker or terminal blocks
are tight.
53

COMMISSIONING

FORM 201.23-NM1 (910)

Grounding

Programmed Options

Verify that the units protective ground terminal(s) are


properly connected to a suitable grounding point. Ensure that all unit internal ground connections are tight.

Verify that the options factory-programmed into the


Micro Panel are in accordance with the customers
order requirements by pressing the OPTIONS key on
the keypad and reading the settings from the display.

Water System
Verify the chilled liquid system has been installed correctly, and has been commissioned with the correct
direction of water flow through the cooler. The inlet
should be at the refrigerant piping connection end of
the cooler. Purge air from the top of the cooler using
the plugged air vent mounted on the top of the cooler
body.
Flow rates and pressure drops must be within the limits given in the Technical Data section. Operation
outside of these limits is undesirable and could cause
damage.
If mains power must be switched OFF for extended
maintenance or an extended shutdown period, the compressor suction, discharge and economizer service stop
valves should be closed (clockwise). If there is a possibility of liquid freezing due to low ambient temperatures, the coolers should be drained or power should
be applied to the chiller. This will allow the cooler
heater to protect the cooler from freezing down to
- 20F. Before placing the unit back in service, valves
should be opened and power must be switched on (if
power is removed for more than 8 hours) for at least 8
hours (24 hours if ambient temperature is below 86F
[30C]) before the unit is restarted.
Flow Switch
Verify a chilled water flow switch is correctly fitted in
the customers piping on the cooler outlet, and wired
into the control panel correctly using shielded cable.

Programmed Settings
Ensure the system cutout and operational settings are in
accordance with the operating requirements by pressing the PROGRAM key.
Date and Time
Program the date and time by first ensuring that the
CLK jumper JP2 on the chiller control board is in the
ON position. See Figures. 26 and 27. Then press the
DATE/TIME key and set the date and time (see Page
277).
Start/Stop Schedule
Program the daily and holiday start/stop by pressing
the SCHEDULE key (see Page 277).
Setpoint and Remote Offset
Set the required leaving chilled liquid temperature
setpoint and Control Range under the SETPOINTS
key. The chilled liquid temperature control settings
need to be set according to the required operating conditions.
If remote temperature reset (offset) is to be used, the
maximum reset required must be programmed by
pressing the SETPOINTS key (see Page 269).
FIRST TIME START-UP

During the commissioning period


there should be sufficient heat load to
run the unit under stable full load
operation to enable the unit controls,
and system operation to be set up correctly, and a commissioning log taken.
Be sure that the chiller is properly
programmed and the Equipment Pre
Start-up and Start-up Checklist (Page
56) is completed.

There should be a straight run of at least five pipe diameters on either side of the flow switch. The flow
switch should be connected to Terminals 2 and 13 in
the panel.
Temperature Sensor(s)
Ensure the leaving liquid temperature sensor is coated
with heat conductive compound (Part No. 013-00890000) and is inserted to the bottom of the water outlet
sensor well in the cooler. This sensor also provides
some freeze protection and must always be fully inserted in the water outlet sensor well.

54

Interlocks
Verify that liquid is flowing through the cooler and that
heat load is present. Ensure that any remote run interlocks are in the run position and that the Daily Schedule requires the unit to run or is overridden.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Unit Switch
Place the UNIT switch on the keypad to the ON position.
Start-up
Press the SYSTEM SWITCHES key and place the system switch for System 1 to the ON position. There
may be a few seconds delay before the first compressor
starts because of the anti-recycle timer). Be ready when
each compressor starts, to switch the UNIT switch OFF
immediately, if any unusual noises or other adverse
conditions develop.
When a compressor is running, the controller monitors
oil pressure, motor current, and various other system
parameters such as discharge pressure, chilled liquid
temperature, etc. Should any problems occur; the control system will immediately take appropriate action
and display the nature of the fault.
Oil Pressure
When a compressor starts, press the relevant System
Pressures key and verify that oil differential pressure
(oil pressure-suction pressure) develops immediately.
If oil pressure does not develop, the automatic controls
will shut down the compressor. Under no circumstances should a restart attempt be made on a compressor, which does not develop oil pressure immediately.
Switch the UNIT switch to the OFF position.
Refrigerant Flow
When a compressor starts, a flow of liquid refrigerant
will be seen in the liquid line sight glass. After several
minutes of operation, and provided a full charge of refrigerant is in the system, the bubbles will disappear
and be replaced by a solid column of liquid.
Loading
Once the unit has been started, all operations are fully
automatic. After an initial period at minimum capacity,
the control system will adjust the unit load depending
on the chilled liquid temperature and rate of temperature change. If a high heat load is present, the controller will increase the speed of the compressor(s).
Condenser and Fan Rotation
Once a compressor is running, discharge pressure rises
as refrigerant is pumped into the air-cooled condenser
coils. This pressure is controlled by stages of fans to
ensure maximum unit efficiency while maintaining sufficient pressure for correct operation of the condensers
and the lubrication system.
JOHNSON CONTROLS

As discharge pressure rises, the condenser fans operate


in stages to control the pressure. Verify that the fans
operate in the correct direction of rotation and operation is correct for the type of unit.
Suction Superheat
Check suction superheat at steady full compressor
load only. Measure suction temperature with a thermocouple on the copper line about 6" (150 mm) before
the compressor suction service valve. Measure suction
pressure at the suction transducer access valve or the
compressor suction service valve. Superheat should
be 10F to 12F (5.55 to 6.67C) and should be reasonably close to the panel display. Superheat setting
is programmable on the control panel, but is not mechanically adjustable. The Flash Tank Drain Valve
controller modulates the 2 phase Drain Valve Stepper
Motor to control system superheat. Superheat control
is a function of suction pressure and suction temperature measurements from the sensors that are routed to
the Chiller Control Board which in turn sends control
signals to the Flash Tank Drain and Fill Valve Controller located in the left, back wall of the Chiller Controls
Cabinet.
Subcooling
Check liquid subcooling at steady full compressor load
only. It is important that all fans are running for the
system. Measure liquid line temperature on the copper line at the main liquid line service valve. Measure liquid pressure at the liquid line service valve.
Subcooling should be 5 to 7F (2.77 to 3.88C). YCIV
0590 subcooling should be 10F (5.55C). No bubbles
should show in the sight glass. If subcooling is out of
range, add or remove refrigerant as required to clear
the sight glass. Do not overcharge the unit. Subcooling
should be checked with a flash tank level of approximately 35% with a clear sight glass.
General Operation
After completion of the above checks for System 1,
switch OFF the SYS 1 switch on the keypad and repeat
the process for each subsequent system. When all run
correctly, stop the unit, switch all applicable switches
to the ON position and restart the unit.
Assure all checks are completed in the Equipment Pre
Start-up and Start-up Checklist (Pages 56 through
61). The chiller is then ready to be placed into operation.

55

COMMISSIONING

FORM 201.23-NM1 (910)

EQUIPMENT PRE-STARTUP and STARTUP CHECKLIST


JOB NAME: _____________________________
SALES ORDER #: ________________________

Proper electrical lock out and tag


procedures must be followed.

LOCATION: _____________________________
SOLD BY: ______________________________
INSTALLING
CONTRACTOR: _________________________
START-UP
TECHNICIAN/
COMPANY: _____________________________
START-UP DATE: ________________________
CHILLER MODEL #: ______________________
SERIAL #: ______________________________
COMPRESSOR #1
MODEL#: ______________________________
SERIAL #: ______________________________

COMPRESSOR #2
MODEL#: ______________________________
SERIAL #: ______________________________
COMPRESSOR #3
MODEL#: ______________________________
SERIAL #: ______________________________
COMPRESSOR #4
MODEL#: ______________________________
SERIAL #: ______________________________
Pre Start-up
Unit Checks (No Power)
The following basic checks should be made with the
customer power to the unit switched off.

56

Check the system 24 hours prior to initial start:


1.
I nspect the unit for shipping or installation
damage.
2.
Ensure that all piping has been completed.
3.
Assure the unit is properly charged and there are
no piping leaks.
4.
Open each system suction service valve, discharge
service valve, economizer service valve, liquid
line stop valve, and oil line ball valve.
5.
The oil separator oil level(s) should be maintained
so that an oil level is visible in either of the oil separator sight glasses when a compressor is running
at high speeds for 10 to 15 minutes. An oil level
may not be visible in the sight glasses when the
compressor is off and it may be necessary to run the
compressor to obtain a level. In shutdown situations and at some load points, much of the oil may
be in the condenser and the level in the separators
may fall below the bottom sight glass.

On systems with dual oil separators per compressor, one separator may show a lower level or no
level, while the other separator shows a level
between the 2 sight glasses. This is normal and a
level is only required in one separator. Do not add
oil to raise the level in the other oil separator.

Oil levels in single separator systems should not
go above the top of the upper sight glass. Dual
separator systems should also not show oil levels
above the top of one of the sight glasses. In the
rare situation where oil levels are high, drain
enough oil to lower the level to the bottom of the
top sight glass.

Sight glasses will vary in type depending upon
the manufacturer of the separator. One type will
have balls that float in the sight glasses to indicate
level. Another type will have a bulls' eye glass.
The bulls' eye glass will tend to appear to lose the
lines in the bulls' eye when the level is above the
JOHNSON CONTROLS

FORM 201.23-NM1 (910)

glass. Oil level should not be above the top sight


glass. In the rare situation where oil levels are
high, drain oil to lower the level to the bottom of
the top sight glass.

Oil levels in the oil separators above the top sight
glass in either oil separator should be avoided and
may cause excessive oil carryover in the system.
High oil concentration in the system may cause
nuisance trips resulting from incorrect readings
on the level sensor and temperature sensors.
Temperature sensor errors may result in poor
refrigerant control and liquid overfeed to the
compressor.

In the unlikely event it is necessary to add oil,
connect a YORK oil pump to the charging valve
on the oil separator, but do not tighten the flare nut
on the delivery tubing. With the bottom (suction
end) of the pump submerged in oil to avoid entrance of air, operate the pump until oil drips from
the flare nut joint, allowing the air to be expelled,
and tighten the flare nut. Open the compressor oil
charging valve and pump in oil until it reaches the
proper level as described above.

When oil levels are high, adding oil


may not visibly increase the level in
the separators during operation. This
may be an indication the level is already too high and the oil is being
pumped out into the system where it
will cause heat transfer and control
problems.
6.
Ensure water pumps are on. Check and adjust
water pump flow rate and pressure drop across
the cooler.

Excessive flow may cause catastrophic damage to the evaporator.

7.
Check the control panel to ensure it is free of
foreign material (wires, metal chips, tools,
documents, etc.).

JOHNSON CONTROLS

8.
Visually inspect wiring (power and control).
Wiring MUST meet N.E.C. and local codes (See
FIG. 25, 31 and 32).
9.
Check tightness of the incoming power wiring
inside the power panel and inside the motor terminal boxes.

10.Check for proper size fuses in control circuits.

11.
V
erify that field wiring matches the 3-phase
power requirements of the chiller. (See chiller
nameplate Page 35).

12.
Be certain all water temperature sensors are inserted completely in their respective wells and are
coated with heat conductive compound.

13.
Ensure the suction line temperature sensors are
strapped onto the suction lines at 4 or 8 Oclock
positions.

14.
Assure the glycol level in the VSD cooling system
is 9 to 15 inches (23 to 28 cm) from the top of the
fill tube. This check should be performed prior
to running the pump.

Never run the glycol pump without


coolant! Running the glycol pump
without coolant may damage the pump
seals.
Always fill the system with approved
YORK coolant (P/N 013-03344-000)
to avoid damage to the pump, cooling
system and the chiller.

15.
Check to assure the remote start/stop for Sys #1
on Terminals 2 to 15 and Sys #2 on Terminals 2 to
16 are closed on the User Terminal Block 1TB to
allow the systems to run. If remote cycling
devices are not utilized, place a wire jumper
between these terminals.

16.
Ensure that the CLK jumper JP2 on the is in the
ON position (See FIG.-26 and 27).

17.
Assure a flow switch is connected between
Terminals 2 and 13 on the User Terminal Block
1TB in the panel. Throttle back flow to assure
the flow switch opens with a loss of flow. It is
recommended that auxiliary pump contacts be
placed in series with the flow switch for additional protection, if the pump is turned off
during chiller operation. Whenever the pump
contacts are used, the coil of the pump starter
should be suppressed with an RC suppressor
(031-00808-000).
57

COMMISSIONING
Start-up
Panel Checks
(Power ON Both System Switches OFF)

You are about to turn power on to this


machine. SAFETY IS NUMBER
ONE! Only qualified individuals are
permitted to service this product. The
qualified individual furthermore is to
be knowledgeable of, and adhere to,
all safe work practices as required by
NEC, OSHA, and NFPA 70E. Proper
personal protection is to be utilized
where and when required.
1.
Assure the chiller OFF/ON UNIT switch at the
bottom of the keypad is OFF.
2.
Apply 3-phase power to the chiller. Turn on the
optional panel circuit breaker if supplied. The
customers disconnection devices can now be
set to ON.
3.
Verify the control panel display is illuminated.
4.
To prevent the compressors from starting, assure
that the system switches under the SYSTEM
SWITCHES key are in the OFF position.
5.
Verify that the voltage supply corresponds to the
unit requirement and is within the limits given in
the Technical Data section.
6.
Ensure the heaters on each compressor are ON
using a clamp-on ammeter. Heater current draw
is approx. 3A.
7.
Verify the Factory Set overload potentiometers
on the VSD Logic Board are set correctly (correct
settings are provided on Page 323). Press the
VSD DATA key and using the arrow keys, scroll
to the compressor overload settings. Verify the
Factory Set overload potentiometer(s) on the
VSD Logic Board (see FIG. 29 and 30) are set
correctly. In the unlikely event that they are not
set correctly, adjust the potentiometers until the
desired values are achieved.

The VSD is powered up and live. High


voltage exists in the area of the circuit
board on the bus bars, VSD Pole Assemblies, and wiring to the input inductor.

FORM 201.23-NM1 (910)

Adjust the potentiometers, if needed, using the table


on Page 323. The locations of the potentiometers are
shown in FIG. 29 and 30. The potentiometers are Sys
1=R19, Sys 2=R64, Sys 3=R42, and Sys 4=R86.

Incorrect settings of the potentiometers may cause damage to the equipment.

Record the Overload Potentiometer settings below:


Compressor Overload Setting:

System 1 = ______________ Amps

System 2 = ______________ Amps

System 3 = ______________ Amps

System 4 = ______________ Amps

8.
Press the STATUS key. If the following message
appears, immediately contact Johnson Controls Product Technical Support. The appearance of this message may mean
the chiller has lost important factory
programmed information. The serial number and other important data may need to be
reprogrammed.
UNIT WARNING: INVALID SERIAL NUMBER
ENTER UNIT SERIAL NUMBER

Changing the programming of this


feature requires the date and time to
be set on the chiller prior to programming. Additional information regarding this message and how to enter the
serial number with the factory provided password is outlined in the Serial Number Programming information on Page 292.

If the following message appears when the STATUS key is pressed, immediately contact Johnson
Controls Product Technical Support. The appearance of this message indicates the chiller is
a High IPLV chiller operating in Standard IPLV
control.
UNIT WARNING: OPTIMIZED EFFICIENCY
DISABLED CONTACT YORK REPRESENTATIVE

58

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Changing the programming of this


feature requires the date and time to
be set on the chiller prior to programming. Additional information regarding this message is provided in the
Enabling Optimized High IPLV
Mode information on Page 293.
9.
Program the required options into the Panel for the
desired operating requirements (see Page 274).
Record the values below:
Display Language = __________________________
Chilled Liquid Mode = ________________________
Local/Remote Mode = _________________________
Display Units = ______________________________
Lead/Lag Control = ___________________________
Remote Temperature Reset = ___________________
Remote Current Reset = _______________________
Remote Sound Limit =_________________________
Low Ambient Cutout =_________________________

Damage to the chiller could result if


the options are improperly programmed.

Chilled Liquid Setpoint


11.
Program the Chilled Liquid Setpoint/Range
and record:
Local Cooling Setpoint = _____________ F (C)
Local Cooling Range = ______ to ______ F (C)
Maximum Remote
Temperature Reset = _______ to ______ F (C)
Date/Time, Daily Schedule, and Clock Jumper
12.
Set the date and time.
13.
Program the Daily Schedule start and stop
times.
14.
Place the panel in Service Mode (see Page 285)
and turn on each fan stage one by one. Ensure
the fans rotate in the correct direction, so air
flow exits the top of the chiller
15.
Remove the cap on the fill tube and run the
glycol pump to verify the level in the fill tube.
Ensure the glycol level in the VSD cooling system is 9 to15 inches (23 to 28 cm) from the top
of the fill tube while running. The pump can be
run by placing the chiller in the Service Mode.
Be sure to re-install the cap before stopping the
glycol pump to avoid overflowing the fill tube
when the glycol pump is turned off. The glycol
system holds about 3.5 gallons of coolant (P/N
013-03344-000) on the largest chiller model.

Programmed Values

Initial Start-up

10.
Program the required operating values into the
microprocessor for cutouts, safeties, etc. and
record them in the chart below (see Page 271
for details).

After the control panel has been programmed and the


compressor heaters have been energized for at least 8
hours (ambient temperature more than 96F (36C)) or
24 hours (ambient temperature less than 86F (30C)),
the chiller may be placed in operation.

Suction Pressure Cutout = ____________ PSIG (kPa)


Low Ambient Cutout = __________________ F (C)
Leaving Chilled Liquid
Temperature Cutout =__________________ F (C)
Motor Current Limit = ___________________% FLA
Pulldown Current Limit Time =______________MIN
Suction Superheat Setpoint = _____________F (C)
Remote Unit ID # = ___________________________
Sound Limit Setpoint = ______________________%

JOHNSON CONTROLS

1. Turn on the UNIT switch and program the


system switches on the keypad to the ON
position.
2. If cooling demand permits, the compressor(s)
will start and a flow of refrigerant will be noted
in the sight glass, after the anti recycle timer
times out and the precharge of the DC Bus is
completed. After several minutes of operation,
the bubbles in the sight glass will disappear and
there will be a solid column of liquid when the
Drain and Feed Valves stabilize the flash tank
level.
59

COMMISSIONING
3. Allow the compressor to run a short time, being
ready to stop it immediately if any unusual noise or
adverse conditions develop. Immediately at
start-up, the compressor may make sounds different from its normal high-pitched sound. This
is due to the compressor coming up to speed
and the initial lack of an oil film sealing the
clearances in the rotors. This should be of no
concern and lasts for only a short time.
4. Check the system operating parameters. Do this by
selecting various displays such as pressures and
temperatures. Compare these to test gauge
readings.
Checking Subcooling and Superheat
The subcooling should always be checked when
charging the system with refrigerant and/or before
checking the superheat. The subcooling measurement
should always be taken with the system loaded, the
economizer solenoid energized, and the level in the
flash tank reasonably stable with a level of approximately 35%.

It may be desirable to check subcooling


with one compressor running to allow
the compressor to operate at full speed
for a period of time to stabilize system
temperatures and pressures.
When the refrigerant charge is correct, there will be
no bubbles in the liquid sight glass with the system
operating under full load conditions, and there will be
5 to 7F (2.77 to 3.78C) subcooled liquid leaving the
condenser. Subcooling should be set at 10F (5.56C).
An overcharged system should be guarded against.
Evidence of overcharge is as follows:
a. If a system is overcharged, the discharge pressure
will be higher than normal. Normal discharge/
condensing pressure can be found in the refrigerant
temperature/pressure chart; use entering air temperature plus 30F (17C) for normal condensing
temperature.
b. The temperature of the liquid refrigerant out of the
condenser should be about 5 to 7F (2.77 to 3.78C)
less than the condensing temperature (The temperature
corresponding to the condensing pressure from the
refrigerant temperature/pressure chart).

60

FORM 201.23-NM1 (910)

The subcooling temperature of each system should be


calculated by recording the temperature of the liquid
line at the outlet of the condenser and subtracting it
from the recorded liquid line pressure at the liquid stop
valve, converted to temperature from the temperature/
pressure chart.
Subcooling
Example:
Liquid line pressure =
110 PSIG converted to 93F (33.9C)
Minus liquid line temp.
-87F (30.6C)
Subcooling =
6F (3.3C)
The subcooling should be adjusted between 5 and 7 F
(2.77 and 3.78C)

This may be difficult to measure, due


to test instrument error and the
difficulty generally encountered when
measuring subcooling on systems
operating with very low condenser
subcooling.
1.
R ecord the liquid line pressure and its
corresponding temperature, liquid line temperature, and subcooling below:
Liq Line Press =
Temp =
Liq Line Temp =
Subcooling =

SYS 1
_____
_____
_____
_____

SYS 2
_____
_____
_____
_____

PSIG (kPa)
F (C)
F (C)
F (C)

Add or remove charge as necessary to obtain a full sight


glass fully loaded while keeping subcooling to about 5
to 7F (2.77 to 3.78C). After an adjustment is made
to the charge, the flash tank level may rise or drop from
the approx. 35% point. Before another measurement is
made, allow the level to stabilize.
After the subcooling is set, the suction superheat
should be checked. The superheat should be checked
only after steady state operation of the chiller has been
established, and the system is running in a fully loaded, stable condition. Correct superheat for a system is

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

between 8 and 12F (4.45 and 6.67C) and should be


reasonably close to the system superheat on the chiller
display.
The superheat is calculated as the difference between
the actual temperature of the returned refrigerant gas
in the suction line entering the compressor and the
temperature corresponding to the suction pressure as
shown in a standard pressure/temperature chart.
Superheat
Example:
Suction Temp = 46F (8C)
minus Suction Press
30 PSIG converted to Temp - 35F (1C)
11F (6C)
The suction temperature should be taken 6" (13 mm)
before the compressor suction service valve, and the
suction pressure is taken at the compressor suction service valve.
No superheat adjustments are necessary and the
electronically controlled Drain Valve need not
be adjusted in the field. Ensure that superheat is
controlling at 8 to 12F (4.45 to 6.67C). The purpose
of this check is primarily to verify the transducer and
suction temperature sensors in a system are providing reasonably accurate outputs to the chiller controls.
It also checks the operation of the Feed and Drain
Valves.

superheat of each system below:

Suction Press =
SP to Temp =
Suction Temp =
Superheat =

SYS 1
_____
_____
_____
_____

SYS 2
_____
_____
_____
_____

PSIG (kPa)
F (C)
F (C)
F (C)

3.
Discharge superheat will typically run approx. 28
to 30F. This can be checked on the micropanel
display. If the suction superheat drops very low
or the economizer feeds liquid into the compressor, the superheat will drop sharply to approx. 2
to 3F.
Leak Checking
1.
Leak check compressors, fittings, and piping to
ensure no leaks.

If the chiller is functioning satisfactorily during
the initial operating period, no safeties trip and
the chiller controls chilled liquid temperature; it
is now ready to be placed into service.

2.
Record the suction temperature, suction pressure,
suction pressure converted to temperature, and

JOHNSON CONTROLS

61

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

62

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SECTION 6 - TECHNICAL DATA


Water Pressure Drop Charts
ENGLISH UNITS

Pressure
Drop Through Two Circuit YCIV Evaporators

cooler
A
B

JOHNSON CONTROLS

MODEL number YCIV


50Hz
0600(S/P)
0590(E/V)
0630(E/V), 0650(S/P)
0700(E/V), 0720(S/P)
0760(E/V)
0800(E/V)
0830(E/V)
0770(S/P)
0840(S/P)
0920(S/P), 0930(E/V)
1000(S/P)

Excessive flow, above the max. GPM,


will damage the evaporator.

63

TECHNICAL DATA

FORM 201.23-NM1 (910)

WATER PRESSURE DROP CHARTS(CONT'D)


SI UNITS

Pressure
Drop Through Two Circuit YCIV Evaporators

cooler
A
B

64

MODEL number YCIV


50Hz
0600(S/P)
0590(E/V)
0630(E/V), 0650(S/P)
0700(E/V), 0720(S/P)
0760(E/V)
0800(E/V)
0830(E/V)
0770(S/P)
0840(S/P)
0920(S/P), 0930(E/V)
1000(S/P)

Excessive flow, above the max. GPM,


will damage the evaporator.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

WATER PRESSURE DROP CHARTS


ENGLISH UNITS

100

Pressure Drop Through Three Circuit YCIV Evaporators


Pressure Drop Through Three Circuit YCIV Evaporators

Pressure Drop (ft H2O)

6
10

1
100

1000

2000

Water Flow Rate (GPM)

EVAP

YCIV MODELS
50Hz

Excessive flow, above the max. GPM,


will damage the evaporator.

1050(E/V)
A

1070(S/P)
1120(E/V)
1180(S/P)
1220(E/V)

1340(S/P)
1380(E/V)
1500(S/P)

JOHNSON CONTROLS

65

TECHNICAL DATA

FORM 201.23-NM1 (910)

WATER PRESSURE DROP CHARTS (CONT'D)


SI UNITS

Pressure Drop Through Three Circuit YCIV Evaporators

EVAP

YCIV MODELS
50Hz

Excessive flow, above the max. GPM,


will damage the evaporator.

1050(E/V)
A

1070(S/P)
1120(E/V)
1180(S/P)
1220(E/V)

1340(S/P)
1380(E/V)
1500(S/P)

66

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

GLYCOL CORRECTION FACTORS

The cooler is designed in accordance with ARI-59092 which allows for an increase in pressure drop of
Thetocooler
is designed
in accordance
with
up
15% above
the design
value shown
on ARIPages 63
590-92 which
allows
increase
in pressure
through
66. Debris
in for
thean
water
may also
cause addidrop
up to 15%
tionalofpressure
drop.above the design value shown
on pages 48-51. Debris in the water may also
cause
additional
When using
glycolpressure
solutions,drop.
pressure drops are higher
than with water (see correction factors to be applied
When using glycol solutions, pressure drops are
when using glycol solutions). Special care must be takhigher than with water (see correction factors to be
en not to exceed the maximum flow rate allowed.
applied when using glycol solutions). Special care

= Correction
Factor
mustAbe
taken not to
exceed the maximum flow
rateBallowed.

= Mean Temperature through Cooler
Correction Factor
C = A=
Concentration
WIW
B= Mean Temperature through Cooler
C= Concentration W/W

Excessive flow, above the max. GPM,


will damage the evaporator.
Excessive flow, above the max. GPM,
will damage the evaporator.

GLYCOL CORRECTION FACTORS


ETHYLENE GLYCOL

1.45
1.40
1.35
1.30
A 1.25

50%
40%

1.20

30% C

1.15

20%

1.10
1.05
-10

-8

-6

-4

-2

0
B

PROPYLENE GLYCOL

1.8
1.7
1.6
1.5
A 1.4

50%
40%

1.3

30% C

1.2

20%

1.1
1.0

JOHNSON CONTROLS

10%
8 C

10%
-10

-8

-6

-4

-2

0
B

8 C
LD10500A

67

TECHNICAL DATA

FORM 201.23-NM1 (910)

WATER TEMPERATURE AND FLOWS


(English Units)
LEAVING WATER
TEMPERATURE (F)

COOLER3 flow
(GPM)

MODEL
number
YCIV

MIN.1

MAX.2

MIN.

MAX.

MIN.

MAX

0600(S/P)
0590(E/V)
0650(S/P)
0630(E/V)
0720(S/P/)
0700(E/V)
0760(E/V)
0770(S/P)
0800(E/V)
0840(S/P)
0830(E/V)
0920(S/P)
0930(E/V)
1000(S/P)
1050(E/V)
1070(S/P)
1120(E/V)
1180(S/P)
1220(E/V)
1340(S/P)
1380(E/V)
1500(S/P)

40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40

60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60

140
160
160
160
160
160
180
180
180
180
180
180
180
180
250
250
250
300
300
300
300
300

675
750
750
750
750
750
750
800
750
800
750
800
800
800
1200
1200
1200
1200
1200
1200
1200
1200

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125

AIR ON CONDENSER (F)

NOTES:
1. For leaving brine temperature below 40F (4.4C), contact your nearest Johnson Controls office for application requirements.
2. For leaving water temperature higher than 60F (15.6C), contact the nearest Johnson Controls office for application guidelines.
3. The evaporator is protected against freezing to -20F (-28.8C) with an electric heater as standard.

68

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

WATER TEMPERATURE AND FLOWS (CONT'D)


(SI Units)
MODEL
number
YCIV
0600(S/P)
0590(E/V)
0650(S/P)
0630(E/V)
0720(S/P/)
0700(E/V)
0760(E/V)
0770(S/P)
0800(E/V)
0840(S/P)
0830(E/V)
0920(S/P)
0930(E/V)
1000(S/P)
1050(E/V)
1070(S/P)
1120(E/V)
1180(S/P)
1220(E/V)
1340(S/P)
1380(E/V)
1500(S/P)

LEAVING WATER
TEMPERATURE (C)

COOLER3 flow
(l/s)

AIR ON CONDENSER (C)

MIN.1

MAX.2

MIN.

MAX.

MIN.

MAX

4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4

15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6

8.8
10.1
10.1
10.1
10.1
10.1
11.4
11.4
11.4
11.4
11.4
11.4
10.1
11.4
11.4
15.8
15.8
18.9
18.9
18.9
18.9
18.9

42.6
47.3
47.3
47.3
47.3
47.3
47.3
50.5
47.3
50.5
47.3
50.5
47.3
50.5
50.5
75.7
75.7
75.7
75.7
75.7
75.7
75.7

-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8
-17.8

51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7

NOTES:
1. For leaving brine temperature below 4.4C, contact your nearest Johnson Controls office for application requirements.
2. For leaving water temperature higher than 15.6C, contact the nearest Johnson Controls office for application guidelines.
3. The evaporator is protected against freezing to -28.8C with an electric heater as standard.

JOHNSON CONTROLS

69

TECHNICAL DATA

FORM 201.23-NM1 (910)

Physical Data (English - Standard Efficiency)


STANDARD EFFICIENCY
MODEL NUMBER (YCIV____ S/P)
0650
0720
0770
0840
2
2
2
2
170/170
185/170
192/175
192/192
5/5
5/5
5/5
5/5

Refrigerant R-134a

General Unit Data


50Hz
0600
Number of Independent Refrigerant Circuits
2
Refrigerant Charge, R-134a, Ckt.-1/Ckt.-2, lbs
162/162
Oil Charge, Ckt.-1/Ckt.-2, gal.
5/5
Compressors, Semi-hermetic Screw Qty per
2
2
Chiller
Condensers, High Efficiency Fin/Tube with Integral Subcooler
Total Chiller Coil Face Area, ft2
235
235
Number of Rows
Fins per Inch
Condenser Fans
Number, Ckt.-1/Ckt.-2
Low Noise Fans
Fan Motor, HP
Total Chiller Airflow, cfm
Ultra Quiet Fans
Fan Motor, HP
Total Chiller Airflow, cfm
Dual Speed Fans - Normal Speed
Fan Motor, hp
Total Chiller, CFM
Dual Speed Fans - Lower Speed
Fan Motor, hp
Total Chiller, CFM
High Static Fans
Fan Motor, hp
Total Chiller, CFM
Evaporator, Direct Expansion
Water Volume, gals.
Maximum Water Side Pressure, PSIG
Maximum Refrigerant Side Pressure, PSIG
Minimum Chilled Water Flow Rate, gpm
Maximum Chilled Water Flow Rate, gpm
Water Connections, inches

0920
2
230/195
5/5

1000
2
230/230
5/5

3
17

3
17

264
3
17

264
3
17

293
3
17

323
3
17

352
3
17

4/4

4/4

5/4

5/4

5/5

6/5

6/6

2
104000

2
104000

2
117000

2
117000

2
130000

2
143000

2
156000

2
104000

2
104000

2
117000

2
117000

2
130000

2
143000

2
156000

2
88000

2
88000

2
99000

2
99000

2
110000

2
121000

2
132000

2
67200

2
67200

2
75600

2
75600

2
84000

2
92400

2
100800

5
104000

5
104000

5
117000

5
117000

5
130000

5
143000

5
156000

67.0
150
235
140
675
8

95.0
150
235
160
750
10

95.0
150
235
160
750
10

140.0
150
235
180
800
10

140.0
150
235
180
800
10

140.0
150
235
180
800
10

140.0
150
235
180
800
10

Contact your nearest Johnson Controls Sales Office for weight data.

70

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

PHYSICAL DATA (ENGLISH - STANDARD EFFICIENCY) (CONT'D)


Refrigerant R-134a
General Unit Data
50Hz
Number of Independent Refrigerant Circuits
Refrigerant Charge, R-134a, Ckt.-1/Ckt.-2, lbs

STANDARD EFFICIENCY
MODEL NUMBER (YCIV____ S/P)
1070
1180
1340
3
3
3
185/170/170

Oil Charge, Ckt.-1/Ckt.-2, gal.


5/4/4
Glycol Charge (43% concentration), gal
5.4
Comp.s, Semihermetic Screw
Quantity per Chiller
3
Condensers, High Efficiency Fin/Tube with Integral Subcooler
Total Chiller Coil Face Area, ft2
381
Number of Rows
3
Fins per Inch
17
Condenser Fans
Number, Ckt.-1/Ckt.-2
5/4/4
Low Noise Fans
Fan Motor, HP/kWi
2/1.8
Total Chiller Airflow, cfm
169000
Ultra Quiet Fans
Fan Motor, HP/kWi
2/1.50
Total Chiller Airflow, cfm
169000
Dual Speed Fans - Normal Speed
Fan Motor, hp
2
Total Chiller, CFM
143000
Dual Speed Fans - Lower Speed
Fan Motor, hp
2
Total Chiller, CFM
109200
High Static Fans
Fan Motor, hp
5
Total Chiller, CFM
169000
Evaporator, Direct Expansion
Water Volume, gals.
202.0
Maximum Water Side Pressure, PSIG
150
Maximum Refrigerant Side Pressure, PSIG
235
Minimum Chilled Water Flow Rate, gpm
250
Maximum Chilled Water Flow Rate, gpm
1200
Water Connections, inches
10

1500
3

185/185/170

185/185/230

230/230/230

5/4/4
5.5

5/5/5
6.0

5/5/5
6.3

411
3
17

469
3
17

528
3
17

5/4/4

5/5/6

6/6/6

2/1.8
182000

2/1.8
208000

2/1.8
234000

2/1.50
182000

2/1.50
208000

2/1.50
234000

2
143000

2
165000

2
165000

2
109200

2
126000

2
126000

5
182000

5
208000

5
234000

236.0
150
235
300
1200
10

236.0
150
235
300
1200
10

236.0
150
235
300
1200
10

Contact your nearest Johnson Controls Sales Office for weight data.

JOHNSON CONTROLS

71

TECHNICAL DATA

FORM 201.23-NM1 (910)

PHYSICAL DATA (English - High Efficiency)


Refrigerant R-134a

HIGH EFFICIENCY
MODEL NUMBER (YCIV____ E/V)
0630
0700
0760
0800
2
2
2
2
185/170 185/185 192/192 225/192
5/5
5/5
5/5
5/5

General Unit Data


50Hz
0590
Number of Independent Refrigerant Circuits
2
Refrigerant Charge, R-134a, Ckt.-1/Ckt.-2, lbs
170/170
Oil Charge, Ckt.-1/Ckt.-2, gal.
5/5
Compressors, Semihermetic Screw Qty per
2
2
Chiller
Condensers, High Efficiency Fin/Tube with Integral Subcooler
Total Chiller Coil Face Area, ft2
235
264
Number of Rows
3
3
Fins per Inch
17
17
Condenser Fans
Number, Ckt.-1/Ckt.-2
4/4
5/4
Low Noise Fans
Fan Motor, HP
2
2
Total Chiller Airflow, cfm
104000
117000
Ultra Quiet Fans
Fan Motor, HP
2
2
Total Chiller Airflow, cfm
104000
117000
Dual Speed Fans - Normal Speed
Fan Motor, hp
2
2
Total Chiller, CFM
88000
99000
Dual Speed Fans - Lower Speed
Fan Motor, hp
2
2
Total Chiller, CFM
67200
75600
High Static Fans
Fan Motor, hp
5
5
Total Chiller, CFM
104000
117000
Evaporator, Direct Expansion
Water Volume, gals.
95.0
95.0
Maximum Water Side Pressure, PSIG
150
150
Maximum Refrigerant Side Pressure, PSIG
235
235
Minimum Chilled Water Flow Rate, gpm
160
160
Maximum Chilled Water Flow Rate, gpm
750
750
Water Connections, inches
10
10

72

0830
2
225/225
5/5

0930
2
230/230
5/5

293
3
17

293
3
17

323
3
17

352
3
17

352
3
17

5/5

5/5

6/5

6/6

6/6

2
130000

2
130000

2
143000

2
156000

2
156000

2
130000

2
130000

2
143000

2
156000

2
156000

2
110000

2
110000

2
121000

2
132000

2
132000

2
84000

2
84000

2
92400

2
100800

2
100800

5
130000

5
130000

5
143000

5
156000

5
156000

95.0
150
235
160
750
10

110.0
150
235
180
750
10

110.0
150
235
180
750
10

110.0
150
235
180
750
10

140.0
150
235
180
800
10

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

PHYSICAL DATA (ENGLISH - HIGH EFFICIENCY) (CONT'D)


Refrigerant R-134a
General Unit Data
Number of Independent Refrigerant Circuits
Refrigerant Charge, R-134a, Ckt.-1/Ckt.-2, lbs

50Hz

HIGH EFFICIENCY
MODEL NUMBER (YCIV____ E/V)
1050
1120
1220
3
3
3
185/185/170

Oil Charge, Ckt.-1/Ckt.-2, gal.


5/5/4
Glycol Charge (43% concentration), gal
5.5
Comp.s, Semihermetic Screw
Quantity per Chiller
3
Condensers, High Efficiency Fin/Tube with Integral Subcooler
Total Chiller Coil Face Area, ft2
411
Number of Rows
3
Fins per Inch
17
Condenser Fans
Number, Ckt.-1/Ckt.-2
5/5/4
Low Noise Fans
Fan Motor, HP/kWi
2/1.8
Total Chiller Airflow, cfm
182000
Ultra Quiet Fans
Fan Motor, HP/kWi
2/1.50
Total Chiller Airflow, cfm
182000
Dual Speed Fans - Normal Speed
Fan Motor, hp
2
Total Chiller, CFM
154000
Dual Speed Fans - Lower Speed
Fan Motor, hp
2
Total Chiller, CFM
117600
High Static Fans
Fan Motor, hp
5
Total Chiller, CFM
195000
Evaporator, Direct Expansion
Water Volume, gals.
202.0
Maximum Water Side Pressure, PSIG
150
Maximum Refrigerant Side Pressure, PSIG
235
Minimum Chilled Water Flow Rate, gpm
250
Maximum Chilled Water Flow Rate, gpm
1200
Water Connections, inches
10

JOHNSON CONTROLS

1380
3

185/185/230

185/185/230

230/230/230

5/5/5
5.7

5/5/5
6.0

5/5/5
6.3

469
3
17

469
3
17

528
3
17

5/5/6

5/5/6

6/6/6

2/1.8
208000

2/1.8
208000

2/1.8
234000

2/1.50
208000

2/1.50
208000

2/1.50
234000

2
176000

2
176000

2
198000

2
134400

2
134400

2
151200

5
247000

5
247000

5
273000

202.0
150
235
250
1200
10

236.0
150
235
300
1200
10

236.0
150
235
300
1200
10

73

TECHNICAL DATA

FORM 201.23-NM1 (910)

PHYSICAL DATA (SI - Standard Efficiency)


Refrigerant R-134a

STANDARD EFFICIENCY
MODEL NUMBER (YCIV____ S/P)
0650
0720
0770
0840
2
2
2
2
77/77
84/77
87/80
87/87
19/19
19/19
19/19
19/19

General Unit Data


50Hz
0600
Number of Independent Refrigerant Circuits
2
Refrigerant Charge, R-134a, Ckt.-1/Ckt.-2, kg.
74/74
Oil Charge, Ckt.-1/Ckt.-2, liters
19/19
Compressors, Semihermetic Screw Qty per
2
2
Chiller
Condensers, High Efficiency Fin/Tube with Integral Subcooler
Total Chiller Coil Face Area, m2
21.8
21.8
Number of Rows
3
3
Fins per meter
669
669
Condenser Fans
Number, Ckt.-1/Ckt.-2
4/4
4/4
Low Noise Fans
Fan Motor, HP/kWi
2/1.50
2/1.50
Total Chiller Airflow, l/sec.
49082
49082
Ultra Quiet Fans
Fan Motor, HP/kWi
2/1.50
2/1.50
Total Chiller Airflow, l/sec.
49082
49082
Dual Speed Fans - Normal Speed
Fan, KWi
1.5
1.5
Total Chiller, m3/s
42
42
Dual Speed Fans - Lower Speed
Fan, KWi
1.5
1.5
Total Chiller, m3/s
32
32
High Static Fans
Fan, KWi
3.7
3.7
Total Chiller, m3/s
49
49
Evaporator, Direct Expansion
Water Volume, liters
253.6
359.6
Maximum Water Side Pressure, Bar
10
10
Maximum Refrigerant Side Pressure, Bar
16
16
Minimum Chilled Water Flow Rate, l/sec.
8.8
10.1
Maximum Chilled Water Flow Rate, l/sec.
42.6
47.3
Water Connections, inches
8
10

74

0920
2
105/89
19/19

1000
2
105/105
19/19

24.5
3
669

24.5
3
669

27.2
3
669

30.0
3
669

32.7
3
669

5/4

5/4

5/5

6/5

6/6

2/1.50
55218

2/1.50
55218

2/1.50
61353

2/1.50
67488

2/1.50
73624

2/1.50
55218

2/1.50
55218

2/1.50
61353

2/1.50
67488

2/1.50
73624

1.5
47

1.5
47

1.5
52

1.5
57

1.5
62

1.5
36

1.5
36

1.5
40

1.5
44

1.5
48

3.7
55

3.7
55

3.7
61

3.7
67

3.7
74

359.6
10
16
10.1
47.3
10

529.9
10
16
11.4
50.5
10

529.9
10
16
11.4
50.5
10

529.9
10
16
11.4
50.5
10

529.9
10
16
11.4
50.5
10

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

PHYSICAL DATA (SI - STANDARD EFFICIENCY) (CONT'D)


Refrigerant R-134a
General Unit Data
50Hz
Number of Independent Refrigerant Circuits

STANDARD EFFICIENCY
MODEL NUMBER (YCIV____ S/P)
1070
1180
1340
3
3
3

1500
3

Refrigerant Charge, R-134a, Ckt.-1/Ckt.-2, kg.

84 / 77 / 77

84 / 84 / 77

84 / 84 / 105

105 / 105 / 105

Oil Charge, Ckt.-1/Ckt.-2, liters

19 / 15 / 15

19 / 19 / 15

19 / 19 / 19

19 / 19 / 19

3
669

38
3
669

44
3
669

49
3
669

5/4/4

5/5/4

5/5/6

6/6/6

2/1.50
79768

2/1.50
85904

2/1.50
98176

2/1.50
110448

2/1.50
79768

2/1.50
85904

2/1.50
98176

2/1.50
110448

1.5
67

1.5
67

1.5
78

1.5
78

1.5
52

1.5
52

1.5
59

1.5
59

3.7
80

3.7
86

3.7
98

3.7
110

764.6
10
16
16
76
245

893.3
10
16
19
76
245

893.3
10
16
19
76
245

893.3
10
16
19
76
245

Glycol Charge (43% concentration), liters


0
Compressors, Semihermetic Screw
Quantity per Chiller
3
Condensers, High Efficiency Fin/Tube with Integral Subcooler
Total Chiller Coil Face Area, m2
35
Number of Rows
Fins per meter
Condenser Fans
Number, Ckt.-1/Ckt.-2
Low Noise Fans
Fan Motor, HP/kWi
Total Chiller Airflow, l/sec.
Ultra Quiet Fans
Fan Motor, HP/kWi
Total Chiller Airflow, l/sec.
Dual Speed Fans - Normal Speed
Fan, KWi
Total Chiller, m3/s
Dual Speed Fans - Lower Speed
Fan, KWi
Total Chiller, m3/s
High Static Fans
Fan, KWi
Total Chiller, m3/s
Evaporator, Direct Expansion
Water Volume, liters
Maximum Water Side Pressure, Bar
Maximum Refrigerant Side Pressure, Bar
Minimum Chilled Water Flow Rate, l/sec.
Maximum Chilled Water Flow Rate, l/sec.
Water Connections, mm

JOHNSON CONTROLS

75

TECHNICAL DATA

FORM 201.23-NM1 (910)

PHYSICAL DATA (SI - High Efficiency)


Refrigerant R-134a

HIGH EFFICIENCY
MODEL NUMBER (YCIV____ E/V)
0630
0700
0760
0800
2
2
2
2
84/77
84/84
87/87
102/87
19/19
19/19
19/19
19/19

General Unit Data


50Hz
0590
Number of Independent Refrigerant Circuits
2
Refrigerant Charge, R-134a, Ckt.-1/Ckt.-2, kg.
77/77
Oil Charge, Ckt.-1/Ckt.-2, liters
19/19
Compressors, Semihermetic Screw Qty per
2
2
Chiller
Condensers, High Efficiency Fin/Tube with Integral Subcooler
Total Chiller Coil Face Area, m2
21.8
24.5
Number of Rows
3
3
Fins per meter
669
669
Condenser Fans
Number, Ckt.-1/Ckt.-2
4/4
5/4
Low Sound Fans
Fan Motor, HP/kWi
2/1.50
2/1.50
Total Chiller Airflow, l/sec.
49082
55218
Ultra Quiet Fans
Fan Motor, HP/kWi
2/1.50
2/1.50
Total Chiller Airflow, l/sec.
49082
55218
Dual Speed Fans - Normal Speed
Fan, KWi
1.5
1.5
Total Chiller, m3/s
42
47
Dual Speed Fans - Lower Speed
Fan, KWi
1.5
1.5
Total Chiller, m3/s
32
36
High Static Fans
Fan, KWi
3.7
3.7
Total Chiller, m3/s
49
55
Evaporator, Direct Expansion
Water Volume, liters
359.6
359.6
10
10
Maximum Water Side Pressure, Bar 1
Maximum Refrigerant Side Pressure, Bar
16
16
Minimum Chilled Water Flow Rate, l/sec.
10.1
10.1
Maximum Chilled Water Flow Rate, l/sec.
47.3
47.3
Water Connections, inches
10
10

76

0830
2
102/102
19/19

0930
2
105/105
19/19

27.2
3
669

27.2
3
669

30.0
3
669

32.7
3
669

32.7
3
669

5/5

5/5

6/5

6/6

6/6

2/1.50
61353

2/1.50
61353

2/1.50
67488

2/1.50
73624

2/1.50
73624

2/1.50
61353

2/1.50
61353

2/1.50
67488

2/1.50
73624

2/1.50
73624

1.5
52

1.5
52

1.5
57

1.5
62

1.5
62

1.5
40

1.5
40

1.5
44

1.5
48

1.5
48

3.7
61

3.7
61

3.7
67

3.7
74

3.7
74

359.6
10
16
10.1
47.3
10

416.4
10
16
11.4
47.3
10

416.4
10
16
11.4
47.3
10

416.4
10
16
11.4
47.3
10

529.9
10
16
11.4
50.5
10

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

PHYSICAL DATA (SI - HIGH EFFICIENCY) (CONT'D)


HIGH EFFICIENCY

Refrigerant R-134a
General Unit Data
50Hz
Number of Independent Refrigerant Circuits

MODEL NUMBER (YCIV____ E/V)

1050
3

1120
3

1220
3

1380
3

Refrigerant Charge, R-134a, Ckt.-1/Ckt.-2, kg.

84 / 84 / 77

84 / 84 / 105

84 / 84 / 105

105 / 105 / 105

Oil Charge, Ckt.-1/Ckt.-2, liters

19 / 19 / 15

19 / 19 / 19

19 / 19 / 19

19 / 19 / 19

44
3
669

44
3
669

49
3
669

05/05/06

05/05/06

06/06/06

2/1.50
98176

2/1.50
98176

2/1.50
110448

2/1.50
98176

2/1.50
98176

2/1.50
110448

1.5
83

1.5
83

1.5
93

1.5
63

1.5
63

1.5
71

3.7
117

3.7
117

3.7
129

764.6
10
16
16
76
245

893.3
10
16
19
76
245

893.3
10
16
19
76
245

Glycol Charge (43% concentration), liters


0
Compressors, Semihermetic Screw
Quantity per Chiller
3
Condensers, High Efficiency Fin/Tube with Integral Subcooler
38
Total Chiller Coil Face Area, m2
Number of Rows
3
Fins per meter
669
Condenser Fans
Number, Ckt.-1/Ckt.-2
05/05/04
Low Noise Fans
Fan Motor, HP/kWi
2/1.50
Total Chiller Airflow, l/sec.
85904
Ultra Quiet Fans
Fan Motor, HP/kWi
2/1.50
Total Chiller Airflow, l/sec.
85904
Dual Speed Fans - Normal Speed
Fan, KWi
1.5
Total Chiller, m3/s
73
Dual Speed Fans - Lower Speed
Fan, KWi
1.5
Total Chiller, m3/s
56
High Static Fans
Fan, KWi
3.7
Total Chiller, m3/s
92
Evaporator, Direct Expansion
Water Volume, liters
764.6
Maximum Water Side Pressure, Bar
10
Maximum Refrigerant Side Pressure, Bar
16
Minimum Chilled Water Flow Rate, l/sec.
16
Maximum Chilled Water Flow Rate, l/sec.
76
Water Connections, mm
245

JOHNSON CONTROLS

77

TECHNICAL DATA

FORM 201.23-NM1 (910)

Electrical data
2 Compressor Power Wiring Connections

FIG. 6 - two COMPressor WIRING DIAGRAM WITH CIRCUIT BREAKER



FIG. 7 - two COMPressor WIRING DIAGRAM WITH TERMINAL BLOCK


78

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

ELECTRICAL DATA (CONT'D)


3 Compressor Power Wiring Connections

FIG. 8 - three COMPressor WIRING DIAGRAM WITH CIRCUIT BREAKER Single Point
3 COMPRESSOR POWER WIRING CONNECTIONS

VSD CONTROL PANEL


VSD
1

VSD
2

VSD
3

STANDARD
CONTROL
TRANSFORMER

UNIT CONTROLS
EVAPORATOR HEATER

FAN
CONTACTORS

TERMINAL
BLOCK

GRD

LINE
REACTOR

See Note 3

FIELD PROVIDED
UNIT POWER
SUPPLY

FIG. 9 - Three COMPressor WIRING DIAGRAM WITH TERMINAL BLOCK Single Point
JOHNSON CONTROLS

79

TECHNICAL DATA

FORM 201.23-NM1 (910)

STANDARD efficiency 2-Compressor Units (See FIG. 6)


One Field Provided Power Supply Circuit. Field Connections to Factory provided
Terminal Block (Standard); or Individual System Breakers (Optional).

Standard Efficiency YCIV_ _ _ _ S/P


System 1

Model No./Nameplate

Std. & Ultra Quiet Cond. Fans

YCIV S/P

Input
Volts (9)

Input
Freq

Compressor
RLA (5)

0600

400

50

144

High Head/Static Cond. Fans

Two-Speed Cond. Fans

Condenser Fans

Compressor

Condenser Fans

Qty.

FLA (EA)

RLA (5)

Qty.

FLA (EA)

Compressor
RLA (5)

3.1

144

9.3

152

Condenser Fans
Qty.

FLA (EA)

3.8

0650

400

50

191

3.1

191

9.3

198

3.8

0720

400

50

195

3.1

195

9.3

207

3.8

0770

400

50

174

3.1

174

9.3

185

3.8

0840

400

50

194

3.1

194

9.3

206

3.8

0920

400

50

232

3.1

232

9.3

246

3.8

1000

400

50

230

3.1

230

9.3

243

3.8

Field Wiring & Protection

Unit Short Circuit Withstand (KA)


YCIV S/P

Control
KVA (7)

Terminal Block
(STD)

Circuit Breaker
(OPT)

Std. & Ultra Quiet Cond. Fans


Minimum Ckt.
Ampacity (MCA)
(3)

Recommended
Fuse/Ckt.
Breaker Rating
(4)

Max. Inverse Time


Ckt. Brkr. Rating
(2)

Max Dual Element Fuse Size


(2)

0600

1.8

30KA

65KA

350

400

450

450

0650

1.8

30KA

65KA

390

450

500

500

0720

1.8

30KA

65KA

416

500

600

600

0770

1.8

30KA

65KA

446

500

600

600

0840

1.8

30KA

65KA

468

600

600

600

0920

1.8

30KA

65KA

517

600

700

700

1000

1.8

30KA

65KA

555

700

700

700

See page 92 for Electrical Data footnotes.

80

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

STANDARD efficiency 2-Compressor Units (CONT'D)


One Field Provided Power Supply Circuit. Field Connections to Factory provided
Terminal Block (Standard); or Individual System Breakers (Optional).

Standard Efficiency YCIV_ _ _ _ S/P


System 2
Std. & Ultra Quiet Cond. Fans
Compressor
RLA (5)

High Head/Static Cond. Fans

Condenser Fans

Compressor
RLA (5)

Two-Speed Cond. Fans

Condenser Fans

Condenser Fans

Compressor
RLA (5)

Qty.

FLA (EA)

Qty.

FLA (EA)

Qty.

FLA (EA)

144

3.1

144

9.3

152

3.8

127

3.1

127

9.3

132

3.8

144

3.1

144

9.3

152

3.8

195

3.1

195

9.3

201

3.8

194

3.1

194

9.3

206

3.8

192

3.1

192

9.3

204

3.8

230

3.1

230

9.3

243

3.8

High Head/High Static Fans


Minimum Ckt.
Ampacity
(MCA) (3)

Recommended
Fuse/Ckt.
Breaker Rating
(4)

Max. Inverse
Time Ckt. Brkr.
Rating (2)

Two-Speed Cond. Fans


Max Dual
Element Fuse
Size (2)

Minimum Ckt.
Ampacity
(MCA) (3)

Recommended
Fuse/Ckt.
Breaker Rating
(4)

Max. Inverse
Time Ckt. Brkr.
Rating (2)

Max Dual Element Fuse Size


(2)

373

450

500

500

399

450

500

500

410

500

600

600

440

500

600

600

445

500

600

600

472

600

600

600

471

600

600

600

502

600

700

700

502

600

700

700

530

600

700

700

553

700

800

800

585

700

800

800

593

700

800

800

629

700

800

800

JOHNSON CONTROLS

81

TECHNICAL DATA

FORM 201.23-NM1 (910)

STANDARD efficiency 2-Compressor Units (CONT'D)


Standard Efficiency YCIV_ _ _ _ S/P
Field Wiring Lugs

Model No./Nameplate

YCIV
S/P

Input
Volts
(9)

Input
Freq

0600

400

50

STD Terminal Block


Std., U.Q. & TwoSpd Cond. Fans

OPT Circuit Breaker


Std., U.Q. & 2-Spd
Cond. Fans

STD Terminal Block


High Head/High
Static Cond. Fans

OPT Circuit Breaker


High Head/High
Static Cond. Fans

Lugs/
Phase
(1)

Lug Wire
Range

Lugs/
Phase
(1)

Lug Wire
Range

Lugs/
Phase
(1)

Lug Wire
Range

Lugs/
Phase
(1)

Lug Wire
Range

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0650

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0720

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0770

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0840

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0920

400

50

#2 - 600 KCM

#3/0 - 400 KCM

#2 - 600 KCM

#2 - 600 KCM

1000

400

50

#2 - 600 KCM

#3/0 - 400 KCM

#2 - 600 KCM

#3/0 - 400 KCM

82

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

JOHNSON CONTROLS

83

TECHNICAL DATA

FORM 201.23-NM1 (910)

high efficiency 2-Compressor Units (See FIG. 7)


One Field Provided Power Supply Circuit. Field Connections to Factory provided
Terminal Block (Standard); or Individual System Breakers (Optional).

High Efficiency YCIV_ _ _ _ E/V


Model No./Nameplate
YCIV E/V

Input
Volts (9)

Input
Freq

System 1
Std. & Ultra Quiet Cond. Fans
Compressor
RLA (5)

Condenser Fans
Qty

FLA (EA)

High Head/Static Cond. Fans


Compressor
RLA (5)

Condenser Fans
Qty.

FLA (EA)

Two-Speed Cond. Fans


Compressor
RLA (5)

Condenser Fans
Qty.

FLA (EA)

0590

400

50

132

3.1

132

9.3

138

3.8

0630

400

50

134

3.1

134

9.3

139

3.8

0700

400

50

185

3.1

185

9.3

196

3.8

0760

400

50

170

3.1

170

9.3

180

3.8

0800

400

50

170

3.1

170

9.3

178

3.8

0830

400

50

180

3.1

180

9.3

189

3.8

0930

400

50

233

3.1

233

9.3

246

3.8

Field Wiring & Protection

Unit Short Circuit Withstand (KA)


YCIV E/V

Control
KVA (7)

0590

Std. & Ultra Quiet Cond. Fans

Terminal Block
(STD)

Circuit Breaker
(OPT)

Minimum Ckt.
Ampacity
(MCA) (3)

Recommended
Fuse/Ckt.
Breaker Rating
(4)

Max. Inverse
Time Ckt. Brkr.
Rating (2)

Max Dual
Element Fuse
Size (2)

1.8

30KA

65KA

322

400

450

450

0630

1.8

30KA

65KA

344

400

450

450

0700

1.8

30KA

65KA

388

450

500

500

0760

1.8

30KA

65KA

412

500

500

500

0800

1.8

30KA

65KA

433

500

600

600

0830

1.8

30KA

65KA

443

500

600

600

0930

1.8

30KA

65KA

506

600

700

700

See page 92 for Electrical Data footnotes.

84

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

High efficiency 2-Compressor Units (CONT'D)


One Field Provided Power Supply Circuit. Field Connections to Factory provided
Terminal Block (Standard); or Individual System Breakers (Optional).

High Efficiency YCIV_ _ _ _ E/V


System 2
Std. & Ultra Quiet Cond. Fans
Compressor
RLA (5)

High Head/Static Cond. Fans

Condenser Fans
Qty.

Condenser Fans

Compressor
RLA (5)

FLA (EA)

Qty.

FLA (EA)

Two-Speed Cond. Fans


Compressor
RLA (5)

Condenser Fans
Qty.

FLA (EA)

132

3.1

132

9.3

138

3.8

146

3.1

146

9.3

154

3.8

126

3.1

126

9.3

131

3.8

170

3.1

170

9.3

180

3.8

183

3.1

183

9.3

195

3.8

180

3.1

180

9.3

189

3.8

178

3.1

178

9.3

187

3.8

Field Wiring & Protection


High Head/High Static Fans

Two-Speed Cond. Fans

Minimum Ckt.
Ampacity
(MCA) (3)

Recommended
Fuse/Ckt.
Breaker Rating
(4)

Max. Inverse
Time Ckt. Brkr.
Rating (2)

Max Dual
Element Fuse
Size (2)

Minimum Ckt.
Ampacity
(MCA) (3)

Recommended
Fuse/Ckt.
Breaker Rating
(4)

Max. Inverse
Time Ckt. Brkr.
Rating (2)

Max Dual
Element Fuse
Size (2)

372

450

500

500

342

400

450

450

400

450

500

500

366

450

500

500

450

500

600

600

414

500

600

600

474

600

600

600

442

500

600

600

501

600

600

600

463

600

600

600

517

600

700

700

472

600

600

600

581

700

800

800

541

700

700

700

JOHNSON CONTROLS

85

TECHNICAL DATA

FORM 201.23-NM1 (910)

High efficiency 2-Compressor Units (CONT'D)


High Efficiency YCIV_ _ _ _ E/V
Field Wiring Lugs

Model No./Nameplate

YCIV
E/V

Input
Volts
(9)

Input
Freq

0590

400

0630

STD Terminal Block


Std., U.Q. & TwoSpd Cond. Fans

OPT Circuit Breaker


Std., U.Q. & 2-Spd
Cond. Fans

STD Terminal Block


High Head/High
Static Cond. Fans

OPT Circuit Breaker


High Head/High
Static Cond. Fans

Lugs/
Phase
(1)

Lug Wire
Range

Lugs/
Phase
(1)

Lug Wire
Range

Lugs/
Phase
(1)

Lug Wire
Range

Lugs/
Phase
(1)

Lug Wire
Range

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0700

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0760

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0800

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0830

400

50

#2 - 600 KCM

#2/0 - 500 KCM

#2 - 600 KCM

#2 - 600 KCM

0930

400

50

#2 - 600 KCM

#3/0 - 400 KCM

#2 - 600 KCM

#3/0 - 400 KCM

86

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

JOHNSON CONTROLS

87

TECHNICAL DATA

FORM 201.23-NM1 (910)

STANDARD efficiency 3-Compressor Units (See FIG. 8)


One Field Provided Power Supply Circuit. Field Connections to Factory provided
Terminal Block (Standard); or Individual System Breakers (Optional).

Model No./Nameplate

YCIV
S/P

Input
Volts
(9)

Input
Freq

1070

400

50

System 1
Std. & Ultra Quiet Cond.
Fans
Comp.

Condenser Fans

System 2

High Head/Static Cond.


Fans
Comp.

Condenser Fans

Two-Speed Cond. Fans


Comp.

Condenser Fans

Std. & Ultra Quiet Cond.


Fans
Comp.

Condenser Fans

RLA
(5)

Qty.

FLA
(EA)

RLA
(5)

Qty.

FLA
(EA)

RLA
(5)

Qty.

FLA
(EA)

RLA
(5)

Qty.

FLA
(EA)

175

3.1

175

9.3

186

3.8

196

3.1

1180

400

50

177

3.1

177

9.3

188

3.8

177

3.1

1340

400

50

192

3.1

192

9.3

204

3.8

192

3.1

1500

400

50

229

3.1

229

9.3

243

3.8

229

3.1

YCIV S/P

Control
KVA (7)

Field Wiring & Protection

Unit Short Circuit Withstand (KA)

Std. & Ultra Quiet Cond. Fans

High Head/High Static Fans

Terminal
Block (STD)

Circuit
Breaker
(OPT)

Minimum
Ckt.
Ampacity
(MCA) (3)

Recommended Fuse/
Ckt. Breaker
Rating (4)

Max. Inverse Time


Ckt. Brkr.
Rating (2)

Max Dual
Element
Fuse Size
(2)

Minimum
Ckt.
Ampacity
(MCA) (3)

Recommended Fuse/
Ckt. Breaker
Rating (4)

1070

2.4

30KA

65KA

590

700

700

700

671

800

1180

2.4

30KA

65KA

644

700

800

800

731

800

1340

2.4

30KA

65KA

724

800

800

800

824

1000

1500

2.4

30KA

65KA

801

1000

1000

1000

913

1000

See page 92 for Electrical Data footnotes.

88

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

STANDARD efficiency 3-Compressor Units (CONT'D)


(One Field Provided Power Supply Circuit. Field Connections to Factory provided
Terminal Block (Standard); or Individual System Breakers (Optional).

System 2
High Head/Static Cond.
Fans
Comp.

System 3

Two-Speed Cond. Fans

Condenser
Fans

Comp.

Std. & Ultra Quiet Cond.


Fans

Condenser
Fans

Comp.

High Head/Static Cond.


Fans

Condenser
Fans

Comp.

Two-Speed Cond. Fans

Condenser
Fans

Comp.

Condenser Fans

RLA
(5)

Qty.

FLA
(EA)

RLA (5)

Qty.

FLA
(EA)

RLA (5)

Qty.

FLA
(EA)

RLA (5)

Qty.

FLA
(EA)

RLA (5)

Qty.

FLA (EA)

196

9.3

202

3.8

129

3.1

129

9.3

135

3.8

177

9.3

188

3.8

198

3.1

198

9.3

203

3.8

192

9.3

204

3.8

232

3.1

232

9.3

245

3.8

229

9.3

243

3.8

229

3.1

229

9.3

243

3.8

Field Wiring & Protection


High Head/High Static
Fans

Field Wiring Lugs

Two-Speed Cond. Fans

STD Terminal Block

OPT Circuit Breaker

Max. Inverse Time


Ckt. Brkr.
Rating (2)

Max Dual
Element
Fuse Size
(2)

Minimum
Ckt.
Ampacity
(MCA) (3)

Recommended Fuse/
Ckt. Breaker
Rating (4)

Max. Inverse Time


Ckt. Brkr.
Rating (2)

Max Dual
Element
Fuse Size
(2)

Lugs/
Phase (1)

Lug Wire
Range

Lugs/
Phase (1)

Lug Wire
Range

800

800

623

700

800

800

#2 - 600
KCM

#4/0 - 500
KCM

800

800

683

800

800

800

#2 - 600
KCM

#4/0 - 500
KCM

1000

1000

776

1000

1000

1000

#2 - 600
KCM

#4/0 - 500
KCM

1000

1000

857

1000

1000

1000

#2 - 600
KCM

#4/0 - 500
KCM

JOHNSON CONTROLS

89

TECHNICAL DATA

FORM 201.23-NM1 (910)

high efficiency 3-Compressor Units (See FIG. 9)


(One Field Provided Power Supply Circuit. Field Connections to Factory provided
Terminal Block (Standard); or Individual System Breakers (Optional).

Model No./Nameplate
YCIV
E/V

Input
Volts
(9)

Input
Freq

Std. & Ultra Quiet Cond.


Fans
Comp.
RLA
(5)

Condenser Fans
FLA
(EA)

Qty.

System 1

System 2

High Head/Static Cond.


Fans

Std. & Ultra Quiet Cond.


Fans

Comp.
RLA
(5)

Condenser Fans
Qty.

FLA
(EA)

Two-Speed Cond. Fans


Comp.
RLA
(5)

Condenser Fans
Qty.

FLA
(EA)

Comp.
RLA
(5)

Condenser Fans
Qty.

FLA
(EA)

1050

400

50

170

3.1

170

9.3

180

3.8

170

3.1

1120

400

50

164

3.1

164

9.3

173

3.8

164

3.1

1220

400

50

183

3.1

183

9.3

194

3.8

183

3.1

1380

400

50

218

3.1

218

9.3

229

3.8

218

3.1

Field Wiring & Protection

Unit Short Circuit Withstand (KA)


YCIV E/V

1050

Control
KVA (7)

2.4

Std. & Ultra Quiet Cond. Fans

High Head/High Static Fans

Terminal
Block (STD)

Circuit
Breaker
(OPT)

Minimum
Ckt.
Ampacity
(MCA) (3)

Recommended Fuse/
Ckt. Breaker
Rating (4)

Max. Inverse Time


Ckt. Brkr.
Rating (2)

Max Dual
Element
Fuse Size
(2)

Minimum
Ckt.
Ampacity
(MCA) (3)

Recommended Fuse/
Ckt. Breaker
Rating (4)

30KA

65KA

552

600

700

700

639

700

1120

2.4

30KA

65KA

580

700

700

700

673

800

1220

2.4

30KA

65KA

631

700

800

800

730

800

1380

2.4

30KA

65KA

713

800

800

800

824

1000

See page 92 for Electrical Data footnotes.

90

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

High efficiency 3-Compressor Units (CONT'D)


(One Field Provided Power Supply Circuit. Field Connections to Factory provided
Terminal Block (Standard); or Individual System Breakers (Optional).

System 2
High Head/Static Cond.
Fans
Comp.
RLA
(5)

Condenser Fans

System 3

Two-Speed Cond. Fans


Comp.

Qty.

FLA
(EA)

RLA
(5)

170

9.3

164

183
218

Condenser Fans

Std. & Ultra Quiet Cond.


Fans
Comp.

Qty.

FLA
(EA)

RLA
(5)

180

3.8

9.3

173

9.3

194

9.3

229

Condenser Fans

High Head/Static Cond.


Fans
Comp.

Qty.

FLA
(EA)

RLA
(5)

126

3.1

3.8

164

3.8

169

3.8

167

Comp.

Condenser Fans

Qty.

FLA
(EA)

RLA
(5)

Qty.

FLA
(EA)

126

9.3

132

3.8

3.1

164

9.3

173

3.8

3.1

169

9.3

178

3.8

3.1

167

9.3

175

3.8

Field Wiring & Protection


High Head/High Static
Fans

Condenser Fans

Two-Speed Cond. Fans

Field Wiring Lugs

Two-Speed Cond. Fans

STD Terminal Block

OPT Circuit Breaker

Max. Inverse Time


Ckt. Brkr.
Rating (2)

Max Dual
Element
Fuse Size
(2)

Minimum
Ckt.
Ampacity
(MCA) (3)

Recommended
Fuse/Ckt.
Breaker Rating (4)

Max. Inverse Time


Ckt. Brkr.
Rating (2)

Max Dual Element Fuse


Size (2)

Lugs/
Phase
(1)

Lug Wire
Range

Lugs/
Phase
(1)

Lug Wire Range

800

800

590

700

700

700

#2 - 600 KCM

#4/0 - 500 KCM

800

800

621

700

700

700

#2 - 600 KCM

#4/0 - 500 KCM

800

800

676

800

800

800

#2 - 600 KCM

#4/0 - 500 KCM

1000

1000

760

800

800

800

#2 - 600 KCM

#4/0 - 500 KCM

JOHNSON CONTROLS

91

TECHNICAL DATA

FORM 201.23-NM1 (910)

Electrical notes
1. As standard, all units have single point power connection. Contact factory for information regarding dual point power units.
2. Maximum Inverse Time Circuit Breaker or Dual Element Fuse - 225% of the largest compressor RLA plus the sum of all the other loads per
NEC 440.22 (A).
3. MCA - Minimum Circuit Ampacity - 125% of the largest compressor RLA plus 100% of the remaining compressor RLAs plus the sum of all
condenser fan FLAs per NEC 440.33
4. Recommended time delay or dual element fuse size - 150%of the largest compressor RLA plus 100% of the remaining compressor RLAs
plus the sum of all condenser fan FLAs.
5. RLA - Rated Load Amps - rated in accordance with UL standard 1995.
6. Local codes may take precedence.
7. Control KVA includes operational controls and evaporator heaters.
8. System inrush current is less than RLA due to the use of York Variable Speed Drive technology. Typical Compressor Starting Current
(first four seconds of start-up):

Rated Voltage

Typical Starting Current per Compressor

380-400/50/3

28A

380/60/3

29A

460/60/3

23A

9. Voltage Utilization Range:


Rated Voltage

380-415/50/3

Utilization Range
360-440

380/60/3

342-402

460/60/3

414-508

LEGEND:
C.B.

CIRCUIT BREAKER

D.E.

DUAL ELEMENT FUSE

DISC SW

DISCONNECT SWITCH

FACT CB

FACTORY-MOUNTED CIRCUIT BREAKER

FLA

FULL LOAD AMPS

HZ

HERTZ

MAX

MAXIMUM

MCA

MINIMUM CIRCUIT AMPACITY

MIN

MINIMUM

MIN NF

MINIMUM NON-FUSED

RLA

RATED LOAD AMPS

S.P. WIRE

SINGLE-POINT WIRING

NOTES:
1. U.L. Label is provided on 60 Hz units for these electrical wiring configurations.
2. Dashed Line = Field Provided Wiring.
3. The above recommendations are based on the National Electric Code and using copper conductors only. Field wiring must also comply with
local codes. Group Rated breaker must be HACR type for cUL machines.

92

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

JOHNSON CONTROLS

93

TECHNICAL DATA

FORM 201.23-NM1 (910)

Electrical wiring DIAGRAMS - 2 compressor models

FIG. 10 - elementary CONTROL wiring diagram 2 compressor models


94

LD13071

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13072

JOHNSON CONTROLS

95

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13678

FIG. 11 - elementary POWER wiring diagram - yciv0590-1000 2 compressor models


96

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13679

JOHNSON CONTROLS

97

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13676

FIG. 12 - power wiring Connection diagram - yciv0157-0267 2 compressor models


98

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13677

JOHNSON CONTROLS

99

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13673

FIG. 13 - control wiring Connection diagram - YCIV0590-1000 2 compressor models


100

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13674

JOHNSON CONTROLS

101

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13675

FIG 13 - control wiring Connection diagram - yciv0590-1000 2 compressor models (CONT'D)


102

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13081

FIG. 14 - power elementary wiring diagram - yciv0590-1000 2 compressor models


JOHNSON CONTROLS

103

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13082

FIG. 14 - power elementary wiring diagram - yciv0590-1000 2 compressor models (CONT'D)


104

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LOCATION LABEL - YCIV0590-1000 2 COMPRESSOR MODELS

LD10519

JOHNSON CONTROLS

105

TECHNICAL DATA

FORM 201.23-NM1 (910)

PANEL LAYOUT - YCIV0590-1000 2 COMPRESSOR MODELS

106

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

JOHNSON CONTROLS

107

TECHNICAL DATA

FORM 201.23-NM1 (910)

Electrical wiring DIAGRAMS - 3 compressor models

LD13084

FIG. 15 - control elementary diagram - yciv1050-1500 3 compressor models


108

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13085

JOHNSON CONTROLS

109

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13086

FIG. 16 - control elementary diagram - yciv1050-1500 3 compressor models


110

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13087

JOHNSON CONTROLS

111

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13088

FIG. 17 - power elementary diagram - yciv1050-1500 3 compressor models


112

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13089

JOHNSON CONTROLS

113

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13090

FIG. 18 - control wiring connection diagram - yciv1050-1500 3 compressor models


114

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13091

JOHNSON CONTROLS

115

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13092

FIG. 18 - control wiring connection diagram - yciv1050-1500 3 compressor models (CONT'D)


116

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

JOHNSON CONTROLS

117

TECHNICAL DATA

FORM 201.23-NM1 (910)

FIG. 19 - power wiring connection diagram - yciv1050-1500 3 compressor models


118

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

JOHNSON CONTROLS

119

TECHNICAL DATA

FORM 201.23-NM1 (910)

FIG. 19 - power wiring connection diagram - yciv1050-1500 3 compressor models (conT'd)


120

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

THIS PAGE INTENTIONALLY LEFT BLANK

JOHNSON CONTROLS

121

TECHNICAL DATA

FORM 201.23-NM1 (910)

LD13097

FIG. 20 - power elemenetary diagram - yciv1050-1500 3 compressor models


122

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

LD13098

FIG. 20 - power elemenetary diagram - yciv1050-1500 3 compressor models (CONT'D)


JOHNSON CONTROLS

123

TECHNICAL DATA

FORM 201.23-NM1 (910)

LOCATION LABEL - YCIV1050-1500 3 COMPRESSOR MODELS

LD13096

124

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

PANEL LAYOUT - YCIV1050-1500 3 COMPRESSOR MODELS

LD13099

JOHNSON CONTROLS

125

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI


YCIV0590E/V and YCIV0600S/P

CONTROL ENTRY
76 WIDE X 343 HIGH

38
POWER
ENTRY
POWER ENTRY
254
X 330
330 HIGH
254 WIDE
WIDE X

102

HIGH

VIEW B-B

44

POWER ENTRY IS ON BOTTOM OF PANEL

305
VIEW C-C

B (EDGE OF UNIT
TO COOLER
CONNECTION)

2238
VIEW A-A

YCIV

0590E/V

485

714

2146

2865

0600S/P

442

739

2286

2797

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

126

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

CG

16 MOUNTING
HOLES (TYP)
X

CONTROL PANEL

ORIGIN

6
1524

358
33 (TYP)

2581

1270

1278

231

VIEW D-D

2387

1151

2032

10"
WATER INLET

2626
5842

Z
846
X

(3) RIGGING HOLES


EACH SIDE (76 X 51)

10"
WATER OUTLET

CG

POWER: SINGLE POINT WITH TERMINAL BLOCK

JOHNSON CONTROLS

127

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV0630E/V, YCIV0650S/P, YCIV0700E/V and YCIV0720S/P

CONTROL ENTRY
76 WIDE X 343 HIGH

38

102

POWER
POWER ENTRY
ENTRY
254 WIDE X 330
254 WIDE X 330 HIGH
HIGH

VIEW B-B

44

305

POWER ENTRY IS ON BOTTOM OF PANEL


VIEW C-C

485
714 (EDGE OF UNIT
TO COOLER
CONNECTION)
2238
VIEW A-A

YCIV

06307E/V

2238

6960

0650S/P

2032

5842

0700E/V

2238

6960

0720S/P

2238

6960

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

128

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

DIMENSIONS (mm) UNLESS OTHERWISE NOTED


16 MOUNTING
HOLES (TYP)

C
G

CONTROL PANEL

ORIGIN

1524

33 (TYP)

358

1770

2192

1270

1278

231

VIEW D-D

2387

1151

(3) RIGGING HOLES


EACH SIDE 76 X 51

10" (WATER INLET)

10" (WATER OUTLET)


2146

A
POWER: SINGLE POINT WITH TERMINAL BLOCK

JOHNSON CONTROLS

2865
2624

846
Z

B
X

129

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV0760E/V and YCIV0770S/P

CONTROL ENTRY
76 WIDE X 343 HIGH

38
POWER
ENTRY
POWER ENTRY
254
254 WIDE
WIDE XX 330
330 HIGH
HIGH

102

VIEW B-B

44

305

POWER ENTRY IS ON BOTTOM OF PANEL


VIEW C-C

A
B

(EDGE OF UNIT
TO COOLER
CONNECTION)

2238
VIEW A-A

YCIV

0760E/V

518

714

2174

2852

0770S/P

564

660

2009

2878

0890S/P

564

660

2009

2878

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

130

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

16 MOUNTING
HOLES (TYP)

C
G

CONTROL PANEL

ORIGIN

1524

33 (TYP)

358

1770

2192

1270

1278

231

VIEW D-D

2387

1151

(3) RIGGING HOLES


EACH SIDE 76 X 51

10" (WATER INLET)

10" (WATER OUTLET)

2235

2624

846
Z

6960
POWER: SINGLE POINT WITH TERMINAL BLOCK

JOHNSON CONTROLS

C
G

131

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV0800E/V and YCIV0830E/V

CONTROL ENTRY
76 WIDE X 343 HIGH

38

102

POWER ENTRY
POWER
ENTRY
254
WIDEXX330
330 HIGH
254 WIDE
HIGH

VIEW B-B

44

POWER ENTRY IS ON BOTTOM OF PANEL

305

VIEW C-C

518

714 (EDGE OF UNIT


TO COOLER
CONNECTION)

2238
VIEW A-A

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

132

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

C
G

X
16 MOUNTING HOLES (TYP)
Y

CONTROL PANEL

ORIGIN

1524

33 (TYP)

358

960
1524

1250

1631

231

1278

VIEW D-D

2387

1151

(4) RIGGING HOLES


EACH SIDE 76 X 51

10" (WATER OUTLET)


7236

10" (WATER INLET)


2174
4590

2852
2355

846

8077

POWER: SINGLE POINT WITH TERMINAL BLOCK


X

JOHNSON CONTROLS

C
G

133

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV0920S/P, YCIV0930E/V, and YCIV1000S/P

CONTROL ENTRY
76 WIDE X 343 HIGH

38

102

POWERENTRY
ENTRY
POWER
254 WIDE
WIDEXX330
330 HIGH
254
HIGH
VIEW B-B

44

POWER ENTRY IS ON BOTTOM OF PANEL

305

VIEW C-C

564

660 (EDGE OF UNIT


TO COOLER
CONNECTION)

2238
VIEW A-A

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

134

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

C
G

X
16 MOUNTING HOLES (TYP)
Y

CONTROL PANEL

ORIGIN

1524

33 (TYP)
358

960
1524

1250

1631

231

1278

VIEW D-D

2387

1151

(4) RIGGING HOLES


EACH SIDE 76 X 51

10" (WATER OUTLET)


7236

POWER: SINGLE POINT WITH TERMINAL BLOCK

10" (WATER INLET)


2009
4590

A
2878
2355

846

8077

Z
X

JOHNSON CONTROLS

C
G

135

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV1050E/V and YCIV1070S/P

CONTROL ENTRY
76 WIDE X 343 HIGH

38
POWER
POWERENTRY
ENTRY
254 WIDE
WIDEXX330
330 HIGH
254
HIGH

102

VIEW B-B

44

POWER ENTRY IS ON BOTTOM OF PANEL

305
VIEW C-C

2238
VIEW A-A

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

136

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


X

CG

19mm MOUNTING HOLES (TYP)

CONTROL PANEL

ORIGIN

1778

33 (TYP)
231
193

2111

2037

2377

1346

1245

231

2387
447
1151
759

(4) RIGGING HOLES


EACH SIDE 76 X 51

10" (WATER OUTLET)

10" (WATER INLET)


371

5024
6060

9068
8565

3584

A
Z
843
X

CG

LD 13663

JOHNSON CONTROLS

137

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV1120E/V

CONTROL ENTRY
76 WIDE X 343 HIGH

38

102

POWER
POWERENTRY
ENTRY
254
254WIDE
WIDEXX330
330 HIGH
HIGH

VIEW B-B

44

POWER ENTRY IS ON BOTTOM OF PANEL

305

VIEW C-C

2238
VIEW A-A

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

138

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

CG

19mm MOUNTING HOLES (TYP)

CONTROL PANEL

ORIGIN

1778

33 (TYP)
231
193

483

1356

2515

1930

1270

1278

231

VIEW D-D
A

2387
447
1151
759

(5) RIGGING HOLES


EACH SIDE 76 X 51

10" (WATER INLET)

10" (WATER OUTLET)

371
10185

5024

8141

5504

Z
3142

945

CG

10699

LD 13664

JOHNSON CONTROLS

139

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV1180S/P

CONTROL ENTRY
76 WIDE X 343 HIGH
38
POWER
POWER ENTRY
ENTRY
254 WIDE
WIDE XX330
330 HIGH
254
HIGH

102

VIEW B-B

44

POWER ENTRY IS ON BOTTOM OF PANEL

305
VIEW C-C

2238
VIEW A-A

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

140

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

CG

19mm MOUNTING HOLES (TYP)

CONTROL PANEL

ORIGIN

6
1778

33 (TYP)
231
193
2111

2037

2377

1346

1245

231
A

D
2387

411
1151
671

(4) RIGGING HOLES


EACH SIDE 76 X 51

10" (WATER INLET)

10" (WATER OUTLET)


381

5024
6060

9068

3584

A
843

9581

LD 13665

JOHNSON CONTROLS

141

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV1220E/V and YCIV1340S/P

CONTROL ENTRY
76 WIDE X 343 HIGH

38

102

POWER
POWER ENTRY
ENTRY
254 WIDE
WIDE XX 330
330 HIGH
HIGH

VIEW B-B

44

POWER ENTRY IS ON BOTTOM OF PANEL

305

VIEW C-C

2238
VIEW A-A

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

142

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

19mm MOUNTING HOLES (TYP)

C
G

X
Y

ORIGIN

CONTROL PANEL

33 (TYP)

1778

231
175

1882

1356

2515

1930

1270

1278

231

VIEW D-D
A

2387
462
1151
638
(5) RIGGING HOLES
EACH SIDE 76 X 51

10" (WATER INLET)

10" (WATER OUTLET)

381
10185

5024

8141

5504

3066

843

Z
X

C
G

10700

LD 13666

JOHNSON CONTROLS

143

TECHNICAL DATA

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)


YCIV1380E/V and YCIV1500S/P

CONTROL ENTRY
76 WIDE X 343 HIGH
38

102

POWERENTRY
ENTRY
POWER
254 WIDE
WIDEXX330
330 HIGH
254
HIGH
VIEW B-B

44

POWER ENTRY IS ON BOTTOM OF PANEL

305
VIEW C-C

2238
VIEW A-A

NOTE:
Placement on a level surface of free of obstructions (including snow, for winter operation) or air circulation ensures rated
performance, reliable operation, and ease of maintenance. Site
restrictions may compromise minimum clearances indicated below,
resulting in unpredictable airflow patterns and possible diminished
performance. Johnson Controls unit controls will optimize operation without nuisance high-pressure safety cutouts; however, the

144

system designer must consider potential performance degradation.


Access to the unit control center assumes the unit is no higher than
on spring isolators. Recommended minimum clearances: side to
wall 2m; rear to wall 2m; control panel to end wall 1.2m;
top no obstructions whatsoever; distance between adjacent
units 3m. No more than one adjacent wall may be higher than
the unit.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Dimensions - 2 and 3 cOMPRESSOR SI (CONT'D)

19mm MOUNTING HOLES (TYP)

ORIGIN
X

CG

CONTROL PANEL

6
1778

33 (TYP)
231
175
1356

483

2863

1930

1270

1278

231

VIEW D-D

2387
462
1151
721
(5) RIGGING HOLES
EACH SIDE 76 X 51
11303

10" (WATER INLET)


381
8334

10" (WATER OUTLET)


5024
5532

3066

843

11816
X

Z
CG

LD 13667

JOHNSON CONTROLS

145

TECHNICAL DATA

FORM 201.23-NM1 (910)

(2 m)

Technical data - clearances

(2 m)

(2 m)

(1.3 m)

LD10506A

NOTES:
1. No obstructions allowed above the unit.
2. Only one adjacent wall may be higher than the unit
3. Adjacent units should be 10 feet (3 Meters) apart.

146

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Isolator Selection and Mounting


Standard Efficiency, English
Units shipped on or after June 15, 2008
L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - in. and Point Loads - lbs

MODEL
YCIV

0600S/P

0650S/P

0720S/P

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(211, 86.8)

Al Fin Coils

1702

1592

1396

1340

Cu Fin Coils

1702

1704

1739

1682

RS&LS1 / Al Fin Coils

1881

1770

1396

1340

RS&LS1 / Cu Fin Coils

1881

1883

1739

1682

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(211, 1.3)

Al Fin Coils

1702

1592

1396

1340

Cu Fin Coils

1702

1704

1739

1682

RS&LS1 / Al Fin Coils

1881

1770

1396

1340

RS&LS1 / Cu Fin Coils

1881

1883

1739

1682

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(211, 86.8)

Al Fin Coils

1720

1614

1667

1609

Cu Fin Coils

1720

1726

2011

1951

RS&LS1 / Al Fin Coils

1898

1792

1667

1609

RS&LS1 / Cu Fin Coils

1898

1905

2011

1951

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(211, 1.3)

Al Fin Coils

1702

1594

1667

1609

Cu Fin Coils

1702

1706

2011

1951

RS&LS1 / Al Fin Coils

1881

1773

1667

1609

RS&LS1 / Cu Fin Coils

1881

1885

2011

1951

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(195.7, 86.8)

(265.4, 86.8)

Al Fin Coils

1715

1579

1559

1274

774

Cu Fin Coils

1715

1700

1898

1653

935

RS&LS1 / Al Fin Coils

1894

1757

1559

1274

774

RS&LS1 / Cu Fin Coils

1894

1878

1898

1653

935

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(195.7, 1.3)

(265.4, 1.3)

Al Fin Coils

1698

1559

1559

1241

664

Cu Fin Coils

1698

1680

1898

1620

825

RS&LS1 / Al Fin Coils

1876

1737

1559

1241

664

RS&LS1 / Cu Fin Coils

1876

1858

1898

1620

825

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

JOHNSON CONTROLS

147

TECHNICAL DATA

FORM 201.23-NM1 (910)

Standard Efficiency, English (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - in. and Point Loads - lbs

MODEL
YCIV

0770S/P

0840S/P

0920S/P

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(195.7, 86.8)

(265.4, 86.8)

Al Fin Coils

1728

1680

1768

1512

915

Cu Fin Coils

1728

1801

2108

1892

1076

RS&LS1 / Al Fin Coils

1907

1858

1768

1512

915

RS&LS1 / Cu Fin Coils

1907

1980

2108

1892

1076

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(195.7, 1.3)

(265.4, 1.3)

Al Fin Coils

1728

1676

1764

1475

800

Cu Fin Coils

1728

1797

2108

1854

961

RS&LS1 / Al Fin Coils

1907

1854

1764

1475

800

RS&LS1 / Cu Fin Coils

1907

1975

2103

1854

961

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(195.7, 86.8)

(265.4, 86.8)

Al Fin Coils

1728

1680

1768

1523

959

Cu Fin Coils

1728

1801

2108

1903

1120

RS&LS1 / Al Fin Coils

1907

1858

1768

1523

959

RS&LS1 / Cu Fin Coils

1907

1980

2108

1903

1120

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(195.7, 1.3)

(265.4, 1.3)

Al Fin Coils

1728

1676

1764

1519

955

Cu Fin Coils

1728

1797

2103

1898

1116

RS&LS1 / Al Fin Coils

1907

1854

1764

1519

955

RS&LS1 / Cu Fin Coils

1907

1975

2103

1898

1116

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(97.2, 86.8)

(161.4, 86.8)

(210.6, 86.8)

(307.9, 86.8)

Al Fin Coils

1728

1638

1248

1160

1261

959

Cu Fin Coils

1728

1728

1488

1435

1609

1199

RS&LS1 / Al Fin Coils

1907

1817

1248

1160

1261

959

RS&LS1 / Cu Fin Coils

1907

1907

1488

1435

1609

1199

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(97.2, 1.3)

(161.4, 1.3)

(210.6, 1.3)

(307.9, 1.3)

Al Fin Coils

1720

1625

1239

1153

1237

955

Cu Fin Coils

1720

1715

1479

1429

1585

1195

RS&LS1 / Al Fin Coils

1898

1803

1239

1153

1237

955

RS&LS1 / Cu Fin Coils

1898

1894

1479

1429

1590

1195

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

148

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Standard Efficiency, English (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - in. and Point Loads - lbs

MODEL
YCIV

1000S/P

1070S/P

1180S/P

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(97.2, 86.8)

(161.4, 86.8)

(210.6, 86.8)

(307.9, 86.8)

Al Fin Coils

1728

1638

1248

1160

1265

1005

Cu Fin Coils

1728

1728

1488

1435

1614

1246

RS&LS1 / Al Fin Coils

1907

1817

1248

1160

1265

1005

RS&LS1 / Cu Fin Coils

1907

1907

1488

1435

1614

1246

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(97.2, 1.3)

(161.4, 1.3)

(210.6, 1.3)

(307.9, 1.3)

Al Fin Coils

1728

1638

1248

1160

1265

1005

Cu Fin Coils

1728

1728

1488

1435

1614

1246

RS&LS1 / Al Fin Coils

1907

1817

1248

1160

1265

1005

RS&LS1 / Cu Fin Coils

1907

1907

1488

1435

1618

1246

LEFT - L

(9.1, 86.8)

(58.1, 86.8)

(111.1, 86.8)

(204.7, 86.8)

(284.9, 86.8)

(368, 86.8)

Al Fin Coils

1753

1585

1821

1810

2123

1175

Cu Fin Coils

1775

1757

2165

2156

2467

1347

RS&LS1 / Al Fin Coils

1929

1761

1821

1810

2189

1462

RS&LS1 / Cu Fin Coils

1885

1933

2165

2156

2533

1634

RIGHT - R

(9.1, 1.3)

(58.1, 1.3)

(111.1, 1.3)

(204.7, 1.3)

(284.9, 1.3)

(368, 1.3)

Al Fin Coils

1753

1596

2407

2414

2635

1179

Cu Fin Coils

1775

1768

2751

2760

2978

1351

RS&LS1 / Al Fin Coils

1929

1773

2407

2414

2701

1466

RS&LS1 / Cu Fin Coils

1951

1944

2751

2760

3045

1638

LEFT - L

(9.1, 86.8)

(58.1, 86.8)

(111.1, 86.8)

(204.7, 86.8)

(284.9, 86.8)

(368, 86.8)

Al Fin Coils

1753

1585

1953

1978

2304

1184

Cu Fin Coils

1775

1757

2297

2324

2648

1356

RS&LS1 / Al Fin Coils

1929

1761

1953

1978

2370

1470

RS&LS1 / Cu Fin Coils

1951

1933

2297

2324

2714

1642

RIGHT - R

(9.1, 1.3)

(58.1, 1.3)

(111.1, 1.3)

(204.7, 1.3)

(284.9, 1.3)

(368, 1.3)

Al Fin Coils

1753

1596

2540

2632

2897

1188

Cu Fin Coils

1775

1768

2884

2978

3241

1338

RS&LS1 / Al Fin Coils

1929

1773

2540

2632

2963

1475

RS&LS1 / Cu Fin Coils

1951

1944

2884

2978

3307

1647

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

JOHNSON CONTROLS

149

TECHNICAL DATA

FORM 201.23-NM1 (910)

Standard Efficiency, English (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - in. and Point Loads - lbs

MODEL
YCIV

1340S/P

1500S/P

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(185.4, 86.8)

(284.4, 86.8)

(358.5, 86.8)

(411.9, 86.8)

Al Fin Coils

1753

1585

1953

1978

1953

1140

946

Cu Fin Coils

1775

1733

2238

2363

2339

1424

1065

RS&LS1 / Al Fin Coils

1929

1761

1953

1978

1953

1316

1122

RS&LS1 / Cu Fin Coils

1951

1909

2238

2363

2339

1601

1241

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(185.4, 1.3)

(284.4, 1.3)

(358.5, 1.3)

(411.9, 1.3)

Al Fin Coils

1753

1596

2540

2632

2540

1151

946

Cu Fin Coils

1775

1715

2824

3018

2926

1435

1065

RS&LS1 / Al Fin Coils

1929

1773

2540

2632

2540

1327

1122

RS&LS1 / Cu Fin Coils

1951

1892

2824

3018

2926

1612

1241

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(185.4, 86.8)

(298.1, 86.8)

(375.2, 86.8)

(456, 86.8)

Al Fin Coils

1766

1607

1953

1978

2041

1404

1056

Cu Fin Coils

1788

1755

2238

2363

2427

1689

1175

RS&LS1 / Al Fin Coils

1942

1784

1953

1978

2041

1581

1232

RS&LS1 / Cu Fin Coils

1964

1931

2238

2363

2427

1865

1351

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(185.4, 1.3)

(298.1, 1.3)

(375.2, 1.3)

(456, 1.3)

Al Fin Coils

1766

1618

2540

2632

2628

1415

1056

Cu Fin Coils

1788

1737

2824

3018

3014

1700

1175

RS&LS1 / Al Fin Coils

1942

1795

2540

2632

2628

1592

1232

RS&LS1 / Cu Fin Coils

1964

1914

2824

3018

3014

1876

1351

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

150

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

HIGH EFFICIENCY, ENGLISH


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - in. and Point Loads - lbs

MODEL
YCIV

0590E/V

0630E/V

0700E/V

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(211, 86.8)

Al Fin Coils

1702

1594

1667

1609

Cu Fin Coils

1702

1706

2011

1951

RS&LS1 / Al Fin Coils

1881

1773

1667

1609

RS&LS1 / Cu Fin Coils

1881

1885

2011

1951

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(211, 1.3)

Al Fin Coils

1702

1594

1667

1609

Cu Fin Coils

1702

1706

2011

1951

RS&LS1 / Al Fin Coils

1881

1773

1667

1609

RS&LS1 / Cu Fin Coils

1881

1885

2011

1951

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(195.7, 86.8)

(265.4, 86.8)

Al Fin Coils

1698

1559

1559

1274

774

Cu Fin Coils

1698

1680

1898

1653

935

RS&LS1 / Al Fin Coils

1876

1737

1559

1274

774

RS&LS1 / Cu Fin Coils

1876

1858

1898

1653

935

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(195.7, 1.3)

(265.4, 1.3)

Al Fin Coils

1698

1559

1559

1241

664

Cu Fin Coils

1698

1680

1898

1620

825

RS&LS1 / Al Fin Coils

1876

1737

1559

1241

664

RS&LS1 / Cu Fin Coils

1876

1858

1898

1620

825

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(195.7, 86.8)

(265.4, 86.8)

Al Fin Coils

1715

1581

1676

1287

820

Cu Fin Coils

1715

1702

2015

1667

981

RS&LS1 / Al Fin Coils

1894

1759

1676

1287

820

RS&LS1 / Cu Fin Coils

1894

1881

2015

1667

981

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(195.7, 1.3)

(265.4, 1.3)

Al Fin Coils

1698

1561

1561

1287

820

Cu Fin Coils

1698

1682

1900

1667

981

RS&LS1 / Al Fin Coils

1876

1739

1561

1287

820

RS&LS1 / Cu Fin Coils

1876

1861

1900

1667

981

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

JOHNSON CONTROLS

151

TECHNICAL DATA

FORM 201.23-NM1 (910)

HIGH Efficiency, English (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - in. and Point Loads - lbs

MODEL
YCIV

0760E/V

0800E/V

0830E/V

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(195.7, 86.8)

(265.4, 86.8)

Al Fin Coils

1720

1609

1618

1354

860

Cu Fin Coils

1720

1731

1958

1733

1021

RS&LS1 / Al Fin Coils

1898

1788

1618

1354

860

RS&LS1 / Cu Fin Coils

1898

1909

1958

1733

1021

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(195.7, 1.3)

(265.4, 1.3)

Al Fin Coils

1720

1609

1618

1354

860

Cu Fin Coils

1720

1731

1958

1733

1021

RS&LS1 / Al Fin Coils

1898

1788

1618

1354

860

RS&LS1 / Cu Fin Coils

1898

1909

1958

1733

1021

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(97.2, 86.8)

(161.4, 86.8)

(210.6, 86.8)

(307.9, 86.8)

Al Fin Coils

1720

1614

1082

994

1093

952

Cu Fin Coils

1720

1704

1323

1270

1442

1193

RS&LS1 / Al Fin Coils

1898

1792

1082

994

1093

952

RS&LS1 / Cu Fin Coils

1898

1883

1323

1270

1442

1193

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(97.2, 1.3)

(161.4, 1.3)

(210.6, 1.3)

(307.9, 1.3)

Al Fin Coils

1720

1614

1082

994

1078

955

Cu Fin Coils

1720

1704

1323

1270

1426

1195

RS&LS1 / Al Fin Coils

1898

1792

1082

994

1078

955

RS&LS1 / Cu Fin Coils

1898

1883

1323

1270

1431

1195

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(97.2, 86.8)

(161.4, 86.8)

(210.6, 86.8)

(307.9, 86.8)

Al Fin Coils

1720

1616

1085

999

1102

1003

Cu Fin Coils

1720

1706

1325

1274

1451

1243

RS&LS1 / Al Fin Coils

1898

1795

1085

999

1102

1003

RS&LS1 / Cu Fin Coils

1898

1885

1325

1274

1451

1243

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(97.2, 1.3)

(161.4, 1.3)

(210.6, 1.3)

(307.9, 1.3)

Al Fin Coils

1720

1616

1085

999

1102

1003

Cu Fin Coils

1720

1706

1325

1274

1451

1243

RS&LS1 / Al Fin Coils

1898

1795

1085

999

1102

1003

RS&LS1 / Cu Fin Coils

1898

1885

1325

1274

1455

1243

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

152

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

HIGH Efficiency, English (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - in. and Point Loads - lbs

MODEL
YCIV

0930E/V

1050E/V

1120E/V

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(97.2, 86.8)

(161.4, 86.8)

(210.6, 86.8)

(307.9, 86.8)

Al Fin Coils

1728

1638

1248

1160

1265

1005

Cu Fin Coils

1728

1728

1488

1435

1614

1246

RS&LS1 / Al Fin Coils

1907

1817

1248

1160

1265

1005

RS&LS1 / Cu Fin Coils

1907

1907

1488

1435

1614

1246

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(97.2, 1.3)

(161.4, 1.3)

(210.6, 1.3)

(307.9, 1.3)

Al Fin Coils

1720

1629

1248

1160

1265

1005

Cu Fin Coils

1720

1720

1488

1435

1614

1246

RS&LS1 / Al Fin Coils

1898

1808

1248

1160

1265

1005

RS&LS1 / Cu Fin Coils

1898

1898

1488

1435

1618

1246

LEFT - L

(9.1, 86.8)

(58.1, 86.8)

(111.1, 86.8)

(204.7, 86.8)

(284.9, 86.8)

(368, 86.8)

Al Fin Coils

1753

1585

1821

1839

2163

1175

Cu Fin Coils

1775

1757

2165

2185

2507

1347

RS&LS1 / Al Fin Coils

1929

1761

1821

1839

2229

1396

RS&LS1 / Cu Fin Coils

1951

1933

2165

2185

2573

1634

RIGHT - R

(9.1, 1.3)

(58.1, 1.3)

(111.1, 1.3)

(204.7, 1.3)

(284.9, 1.3)

(368, 1.3)

Al Fin Coils

1753

1596

2407

2493

2756

1179

Cu Fin Coils

1775

1768

2751

2840

3100

1351

RS&LS1 / Al Fin Coils

1929

1773

2407

2493

2822

1466

RS&LS1 / Cu Fin Coils

1951

1944

2751

2840

3166

1638

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(185.4, 86.8)

(284.4, 86.8)

(358.5, 86.8)

(411.9, 86.8)

Al Fin Coils

1753

1585

1847

1870

1574

1049

928

Cu Fin Coils

1775

1733

2132

2255

1960

1334

1047

RS&LS1 / Al Fin Coils

1929

1761

1847

1870

1574

1226

1105

RS&LS1 / Cu Fin Coils

1885

1909

2132

2255

1960

1510

1224

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(185.4, 1.3)

(284.4, 1.3)

(358.5, 1.3)

(411.9, 1.3)

Al Fin Coils

1753

1596

2434

2524

2344

1120

928

Cu Fin Coils

1775

1715

2718

2910

2729

1404

1047

RS&LS1 / Al Fin Coils

1929

1773

2434

2524

2344

1296

1105

RS&LS1 / Cu Fin Coils

1951

1892

2718

2910

2729

1581

1224

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

JOHNSON CONTROLS

153

TECHNICAL DATA

FORM 201.23-NM1 (910)

HIGH Efficiency, English (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - in. and Point Loads - lbs

MODEL
YCIV

1220E/V

1380E/V

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(185.4, 86.8)

(284.4, 86.8)

(358.5, 86.8)

(411.9, 86.8)

Al Fin Coils

1753

1585

1953

1978

1953

1140

928

Cu Fin Coils

1775

1733

2238

2363

2339

1424

1047

RS&LS1 / Al Fin Coils

1929

1761

1953

1978

1953

1316

1105

RS&LS1 / Cu Fin Coils

1951

1931

2238

2363

2339

1601

1224

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(185.4, 1.3)

(284.4, 1.3)

(358.5, 1.3)

(411.9, 1.3)

Al Fin Coils

1753

1596

2540

2632

2540

1151

928

Cu Fin Coils

1775

1715

2824

3018

2926

1435

1047

RS&LS1 / Al Fin Coils

1929

1773

2540

2632

2540

1327

1105

RS&LS1 / Cu Fin Coils

1951

1892

2824

3018

2926

1612

1224

LEFT - L

(9.1, 86.8)

(59.4, 86.8)

(109.4, 86.8)

(185.4, 86.8)

(298.1, 86.8)

(375.2, 86.8)

(456, 86.8)

Al Fin Coils

1766

1607

1953

1978

2041

1404

1038

Cu Fin Coils

1788

1755

2238

2363

2427

1689

1157

RS&LS1 / Al Fin Coils

1942

1784

1953

1978

2041

1581

1215

RS&LS1 / Cu Fin Coils

1964

1931

2238

2363

2427

1865

1334

RIGHT - R

(9.1, 1.3)

(59.4, 1.3)

(109.4, 1.3)

(185.4, 1.3)

(298.1, 1.3)

(375.2, 1.3)

(456, 1.3)

Al Fin Coils

1766

1618

2540

2632

2628

1415

1038

Cu Fin Coils

1788

1737

2824

3018

3014

1700

1157

RS&LS1 / Al Fin Coils

1942

1795

2540

2632

2628

1592

1215

RS&LS1 / Cu Fin Coils

1964

1914

2824

3018

3014

1876

1334

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

154

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Standard Efficiency, SI
L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - mm. and Point Loads - kg

MODEL
YCIV

0600S/P

0650S/P

0720S/P

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(5360, 2204)

Al Fin Coils

772

722

633

608

Cu Fin Coils

772

773

789

763

RS&LS1 / Al Fin Coils

853

803

633

608

RS&LS1 / Cu Fin Coils

853

854

789

763

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(5360, 32)

Al Fin Coils

772

722

633

608

Cu Fin Coils

772

773

789

763

RS&LS1 / Al Fin Coils

853

803

633

608

RS&LS1 / Cu Fin Coils

853

854

789

763

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(5360, 2204)

Al Fin Coils

780

732

756

730

Cu Fin Coils

780

783

912

885

RS&LS1 / Al Fin Coils

861

813

756

730

RS&LS1 / Cu Fin Coils

861

864

912

885

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(5360, 32)

Al Fin Coils

772

723

756

730

Cu Fin Coils

772

774

912

885

RS&LS1 / Al Fin Coils

853

804

756

730

RS&LS1 / Cu Fin Coils

853

855

912

885

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4970, 2204)

(6740, 2204)

Al Fin Coils

778

716

707

578

351

Cu Fin Coils

778

771

861

750

424

RS&LS1 / Al Fin Coils

859

797

707

578

351

RS&LS1 / Cu Fin Coils

859

852

861

750

424

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4970, 32)

(6740, 32)

Al Fin Coils

770

707

707

563

301

Cu Fin Coils

770

762

861

735

374

RS&LS1 / Al Fin Coils

851

788

707

563

301

RS&LS1 / Cu Fin Coils

851

843

861

735

374

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

JOHNSON CONTROLS

155

TECHNICAL DATA

FORM 201.23-NM1 (910)

Standard Efficiency, SI (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - mm. and Point Loads - kg

MODEL
YCIV

0770S/P

0840S/P

0920S/P

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4970, 2204)

(6740, 2204)

Al Fin Coils

784

762

802

686

415

Cu Fin Coils

784

817

956

858

488

RS&LS1 / Al Fin Coils

865

843

802

686

415

RS&LS1 / Cu Fin Coils

865

898

956

858

488

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4970, 32)

(6740, 32)

Al Fin Coils

784

760

800

669

363

Cu Fin Coils

784

815

956

841

436

RS&LS1 / Al Fin Coils

865

841

800

669

363

RS&LS1 / Cu Fin Coils

865

896

954

841

436

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4970, 2204)

(6740, 2204)

Al Fin Coils

784

762

802

691

435

Cu Fin Coils

784

817

956

863

508

RS&LS1 / Al Fin Coils

865

843

802

691

435

RS&LS1 / Cu Fin Coils

865

898

956

863

508

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4970, 32)

(6740, 32)

Al Fin Coils

784

760

800

689

433

Cu Fin Coils

784

815

954

861

506

RS&LS1 / Al Fin Coils

865

841

800

689

433

RS&LS1 / Cu Fin Coils

865

896

954

861

506

LEFT - L

(230, 2204)

(1510, 2204)

(24700, 2204)

(4100, 2204)

(5350, 2204)

(1820, 2204)

Al Fin Coils

784

743

566

526

572

435

Cu Fin Coils

784

784

675

651

730

544

RS&LS1 / Al Fin Coils

865

824

566

526

572

435

RS&LS1 / Cu Fin Coils

865

865

675

651

730

544

RIGHT - R

(230, 32)

(1510, 32)

(2470, 32)

(4100, 32)

(5350, 32)

(7820, 32)

Al Fin Coils

780

737

562

523

561

433

Cu Fin Coils

780

778

671

648

719

542

RS&LS1 / Al Fin Coils

861

818

562

523

561

433

RS&LS1 / Cu Fin Coils

861

859

671

648

721

542

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

156

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Standard Efficiency, SI (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - mm. and Point Loads - kg

MODEL
YCIV

1000S/P

1070S/P

1180S/P

LEFT - L

(230, 2204)

(1510, 2204)

(2470, 2204)

(4100, 2204)

(5350, 2204)

(7820, 2204)

Al Fin Coils

784

743

566

526

574

456

Cu Fin Coils

784

784

675

651

732

565

RS&LS1 / Al Fin Coils

865

824

566

526

574

456

RS&LS1 / Cu Fin Coils

865

865

675

651

732

565

RIGHT - R

(230, 32)

(1510, 32)

(2470, 32)

(4100, 32)

(5350, 32)

(7820, 32)

Al Fin Coils

784

743

566

526

574

456

Cu Fin Coils

784

784

675

651

732

565

RS&LS1 / Al Fin Coils

865

824

566

526

574

456

RS&LS1 / Cu Fin Coils

865

865

675

651

734

565

LEFT - L

(230, 2204)

(1475, 2204)

(2823, 2204)

(5199, 2204)

(7236, 2204)

(9346, 2204)

Al Fin Coils

795

719

826

821

963

533

Cu Fin Coils

805

797

982

978

1119

611

RS&LS1 / Al Fin Coils

875

799

826

821

993

663

RS&LS1 / Cu Fin Coils

855

877

982

978

1149

741

RIGHT - R

(230, 32)

(1475, 32)

(2823, 32)

(5199, 32)

(7236, 32)

(9346, 32)

Al Fin Coils

795

724

1092

1095

1195

535

Cu Fin Coils

805

802

1248

1252

1351

613

RS&LS1 / Al Fin Coils

875

804

1092

1095

1225

665

RS&LS1 / Cu Fin Coils

885

882

1248

1252

1381

743

LEFT - L

(230, 2204)

(1475, 2204)

(2823, 2204)

(5199, 2204)

(7236, 2204)

(9346, 2204)

Al Fin Coils

795

719

886

897

1045

537

Cu Fin Coils

805

797

1042

1054

1201

615

RS&LS1 / Al Fin Coils

875

799

886

897

1075

667

RS&LS1 / Cu Fin Coils

885

877

1042

1054

1231

745

RIGHT - R

(230, 32)

(1475, 32)

(2823, 32)

(5199, 32)

(7236, 32)

(9346, 32)

Al Fin Coils

795

724

1152

1194

1314

539

Cu Fin Coils

805

802

1308

1351

1470

607

RS&LS1 / Al Fin Coils

875

804

1152

1194

1344

669

RS&LS1 / Cu Fin Coils

885

882

1308

1351

1500

747

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

JOHNSON CONTROLS

157

TECHNICAL DATA

FORM 201.23-NM1 (910)

Standard Efficiency, SI (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - mm. and Point Loads - kg

MODEL
YCIV

1340S/P

1500S/P

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4710, 2204)

(7225, 2204)

(9105, 2204)

(10463, 2204)

Al Fin Coils

795

719

886

897

886

517

429

Cu Fin Coils

805

786

1015

1072

1061

646

483

RS&LS1 / Al Fin Coils

875

799

886

897

886

597

509

RS&LS1 / Cu Fin Coils

885

866

1015

1072

1061

726

563

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4710, 32)

(7225, 32)

(9105, 32)

(10463, 32)

Al Fin Coils

795

724

1152

1194

1152

522

429

Cu Fin Coils

805

778

1281

1369

1327

651

483

RS&LS1 / Al Fin Coils

875

804

1152

1194

1152

602

509

RS&LS1 / Cu Fin Coils

885

858

1281

1369

1327

731

563

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4710, 2204)

(7572, 2204)

(9530, 2204)

(11582, 2204)

Al Fin Coils

801

729

886

897

926

637

479

Cu Fin Coils

811

796

1015

1072

1101

766

533

RS&LS1 / Al Fin Coils

881

809

886

897

926

717

559

RS&LS1 / Cu Fin Coils

891

876

1015

1072

1101

846

613

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4710, 32)

(7572, 32)

(9530, 32)

(11582, 32)

Al Fin Coils

801

734

1152

1194

1192

642

479

Cu Fin Coils

811

788

1281

1369

1367

771

533

RS&LS1 / Al Fin Coils

881

814

1152

1194

1192

722

559

RS&LS1 / Cu Fin Coils

891

868

1281

1369

1367

851

613

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

158

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

HIGH Efficiency, SI
L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - mm. and Point Loads - kg

MODEL
YCIV

0590E/V

0630E/V

0700E/V

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(5360, 2204)

Al Fin Coils

772

723

756

730

Cu Fin Coils

772

774

912

885

RS&LS1 / Al Fin Coils

853

804

756

730

RS&LS1/ Cu Fin Coils

853

855

912

885

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(5360, 32)

Al Fin Coils

772

723

756

730

Cu Fin Coils

772

774

912

885

RS&LS1 / Al Fin Coils

853

804

756

730

RS&LS1/ Cu Fin Coils

853

855

912

885

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4970, 2204)

(6740, 2204)

Al Fin Coils

770

707

707

578

351

Cu Fin Coils

770

762

861

750

424

RS&LS1 / Al Fin Coils

851

788

707

578

351

RS&LS1/ Cu Fin Coils

851

843

861

750

424

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4970, 32)

(6740, 32)

Al Fin Coils

770

707

707

563

301

Cu Fin Coils

770

762

861

735

374

RS&LS1 / Al Fin Coils

851

788

707

563

301

RS&LS1/ Cu Fin Coils

851

843

861

735

374

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4970, 2204)

(6740, 2204)

Al Fin Coils

778

717

760

584

372

Cu Fin Coils

778

772

914

756

445

RS&LS1 / Al Fin Coils

859

798

760

584

372

RS&LS1/ Cu Fin Coils

859

853

914

756

445

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4970, 32)

(6740, 32)

Al Fin Coils

770

708

708

584

372

Cu Fin Coils

770

763

862

756

445

RS&LS1 / Al Fin Coils

851

789

708

584

372

RS&LS1/ Cu Fin Coils

851

844

862

756

445

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

JOHNSON CONTROLS

159

TECHNICAL DATA

FORM 201.23-NM1 (910)

HIGH Efficiency, SI (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - mm. and Point Loads - kg

MODEL
YCIV

0760E/V

0800E/V

0830E/V

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4970, 2204)

(6740, 2204)

Al Fin Coils

780

730

734

614

390

Cu Fin Coils

780

785

888

786

463

RS&LS1 / Al Fin Coils

861

811

734

614

390

RS&LS1/ Cu Fin Coils

861

866

888

786

463

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4970, 32)

(6740, 32)

Al Fin Coils

780

730

734

614

390

Cu Fin Coils

780

785

888

786

463

RS&LS1 / Al Fin Coils

861

811

734

614

390

RS&LS1/ Cu Fin Coils

861

866

888

786

463

LEFT - L

(230, 2204)

(1510, 2204)

(2470, 2204)

(4100, 2204)

(5350, 2204)

(7820, 2204)

Al Fin Coils

780

732

491

451

496

432

Cu Fin Coils

780

773

600

576

654

541

RS&LS1 / Al Fin Coils

861

813

491

451

496

432

RS&LS1/ Cu Fin Coils

861

854

600

576

654

541

RIGHT - R

(230, 32)

(1510, 32)

(2470, 32)

(4100, 32)

(5350, 32)

(7820, 32)

Al Fin Coils

780

732

491

451

489

433

Cu Fin Coils

780

773

600

576

647

542

RS&LS1 / Al Fin Coils

861

813

491

451

489

433

RS&LS1/ Cu Fin Coils

861

854

600

576

649

542

LEFT - L

(230, 2204)

(1510, 2204)

(2470, 2204)

(4100, 2204)

(5350, 2204)

(7820, 2204)

Al Fin Coils

780

733

492

453

500

455

Cu Fin Coils

780

774

601

578

658

564

RS&LS1 / Al Fin Coils

861

814

492

453

500

455

RS&LS1/ Cu Fin Coils

861

855

601

578

658

564

RIGHT - R

(230, 32)

(1510, 32)

(2470, 32)

(4100, 32)

(5350, 32)

(7820, 32)

Al Fin Coils

780

733

492

453

500

455

Cu Fin Coils

780

774

601

578

658

564

RS&LS1 / Al Fin Coils

861

814

492

453

500

455

RS&LS1/ Cu Fin Coils

861

855

601

578

660

564

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

160

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

HIGH Efficiency, SI (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - mm. and Point Loads - kg

MODEL
YCIV

0930E/V

1050E/V

1120E/V

LEFT - L

(230, 2204)

(1510, 2204)

(2470, 2204)

(4100, 2204)

(5350, 2204)

(7820, 2204)

Al Fin Coils

784

743

566

526

574

456

Cu Fin Coils

784

784

675

651

732

565

RS&LS1 / Al Fin Coils

865

824

566

526

574

456

RS&LS1/ Cu Fin Coils

865

865

675

651

732

565

RIGHT - R

(230, 32)

(1510, 32)

(2470, 32)

(4100, 32)

(5350, 32)

(7820, 32)

Al Fin Coils

780

739

566

526

574

456

Cu Fin Coils

780

780

675

651

732

565

RS&LS1 / Al Fin Coils

861

820

566

526

574

456

RS&LS1/ Cu Fin Coils

861

861

675

651

734

565

LEFT - L

(230, 2204)

(1475, 2204)

(2823, 2204)

(5199, 2204)

(7236, 2204)

(9346, 2204)

Al Fin Coils

795

719

826

834

981

533

Cu Fin Coils

805

797

982

991

1137

611

RS&LS1 / Al Fin Coils

875

799

826

834

1011

633

RS&LS1/ Cu Fin Coils

885

877

982

991

1167

741

RIGHT - R

(230, 32)

(1475, 32)

(2823, 32)

(5199, 32)

(7236, 32)

(9346, 32)

Al Fin Coils

795

724

1092

1131

1250

535

Cu Fin Coils

805

802

1248

1288

1406

613

RS&LS1 / Al Fin Coils

875

804

1092

1131

1280

665

RS&LS1/ Cu Fin Coils

885

882

1248

1288

1436

743

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4710, 2204)

(7225, 2204)

(9105, 2204)

(10463, 2204)

Al Fin Coils

795

719

838

848

714

476

421

Cu Fin Coils

805

786

967

1023

889

605

475

RS&LS1 / Al Fin Coils

875

799

838

848

714

556

501

RS&LS1/ Cu Fin Coils

855

866

967

1023

889

685

555

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4710, 32)

(7225, 32)

(9105, 32)

(10463, 32)

Al Fin Coils

795

724

1104

1145

1063

508

421

Cu Fin Coils

805

778

1233

1320

1238

637

475

RS&LS1 / Al Fin Coils

875

804

1104

1145

1063

588

501

RS&LS1/ Cu Fin Coils

885

858

1233

1320

1238

717

555

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

JOHNSON CONTROLS

161

TECHNICAL DATA

FORM 201.23-NM1 (910)

HIGH Efficiency, SI (CONT'D)


L2

L3

L4

L5

L6

L7

R2

R3

R4

R5

R6

R7

CONTROL PANEL

L1

R1

Isolator Locations (x, y) - mm. and Point Loads - kg

MODEL
YCIV

1220E/V

1380E/V

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4710, 2204)

(7225, 2204)

(9105, 2204)

(10463, 2204)

Al Fin Coils

795

719

886

897

886

517

421

Cu Fin Coils

805

786

1015

1072

1061

646

475

RS&LS1 / Al Fin Coils

875

799

886

897

886

597

501

RS&LS1/ Cu Fin Coils

885

876

1015

1072

1061

726

555

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4710, 32)

(7225, 32)

(9105, 32)

(10463, 32)

Al Fin Coils

795

724

1152

1194

1152

522

421

Cu Fin Coils

805

778

1281

1369

1327

651

475

RS&LS1 / Al Fin Coils

875

804

1152

1194

1152

602

501

RS&LS1/ Cu Fin Coils

885

858

1281

1369

1327

731

555

LEFT - L

(230, 2204)

(1510, 2204)

(2780, 2204)

(4710, 2204)

(7572, 2204)

(9530, 2204)

(11582, 2204)

Al Fin Coils

801

729

886

897

926

637

471

Cu Fin Coils

811

796

1015

1072

1101

766

525

RS&LS1 / Al Fin Coils

881

809

886

897

926

717

551

RS&LS1/ Cu Fin Coils

891

876

1015

1072

1101

846

605

RIGHT - R

(230, 32)

(1510, 32)

(2780, 32)

(4710, 32)

(7572, 32)

(9530, 32)

(11582, 32)

Al Fin Coils

801

734

1152

1194

1192

642

471

Cu Fin Coils

811

788

1281

1369

1367

771

525

RS&LS1 / Al Fin Coils

881

814

1152

1194

1192

722

551

RS&LS1/ Cu Fin Coils

891

868

1281

1369

1367

851

605

NOTES:1. RS = Reduced Sound Option, LS = Low Sound Option

162

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Isolator Cross Reference


Old Part Number
029-24583-002
029-24583-003
029-24583-004
029-24583-005
029-24583-006
029-24583-007
029-24583-008
029-24583-009
029-24583-010
029-24583-011
029-24583-012
029-24583-013
029-24584-001
029-24584-002
029-24584-004
029-24585-006
029-24585-007
029-24585-008
029-24585-009
029-24585-010
029-24585-011
029-24585-012
029-24585-013
029-24585-014

JOHNSON CONTROLS

MASON
CIP-B-450 RED
CIP-B-750 WHITE
CIP-B-1000 BLUE
CIP-B-1250 GRAY
CIP-B-1650 BLACK
CIP-C-1000 BLACK
CIP-C-1350 YELLOW
CIP-C-1750 BLACK STRIPE WITH RED
CIP-C-2100 YELLOW WITH RED
CIP-C-2385 YELLOW WITH GREEN
CIP-C-2650 RED WITH RED
CIP-C-2935 RED WITH GREEN
ND-C YELLOW
ND-D YELLOW
ND-DS YELLOW
SLRS-2-C2-420 RED
SLRS-2-C2-520 WHITE
SLRS-2-C2-660 BLACK
SLRS-2-C2-920 BLUE
SLRS-2-C2-1220 GREEN
SLRS-2-C2-1760 GRAY
SLRS-2-C2-2420 SILVER
SLRS-2-C2-3080 GRAY WITH RED
SLRS-2-C2-3740 SILVER WITH RED

New Part Number


029-25334-002
029-25334-003
029-25334-004
029-25334-005
029-25334-006

the VMC
CP-1D-510 BLACK
CP-1D-900 DK GREEN
CP-1D-1200 GRAY
CP-1D-1360 WHITE
CP-1 D-1785N GRAY IRED

029-25334-008

C2P-1D-1350 DARK PURPLE

029-25334-009

C2P-1D-1800 DARK GREEN

029-25334-010

C2P-1D-2400 GRAY

029-25334-012
029-25334-013
029-25335-001
029-25335-002
029-25335-004

C2P-1D-2720 WHITE
C2P-1D-3570N GRAY/iRED
RD-3 CHARCOAL-WR
RD-4 BRICK RED-WR
RD-4 CHARCOAL-WR

029-25336-006

Y2RSI-2D-460 GREEN

029-25336-008
029-25336-009
029-25336-010
029-25336-011
029-25336-012
029-25336-013
029-25336-014

Y2RSI-2D-710 DK BROWN
Y2RSI-2D-870 RED
Y2RSI-2D-1200N RED/BLACK
Y2RSI-2D-1690 PINK
Y2RSI-2D-2640N PINK/GRAY
Y2RSI-2D-2870N PINK/GRAY/ORANGE
Y2RSI-2D-3600 PINK/GRAY/BROWN

163

TECHNICAL DATA

FORM 201.23-NM1 (910)

One Inch Deflection Spring Isolators Cross-reference


Units shipped on or after June 15, 2008

RATED
EFLECTION
(IN)

COLOR CODE

1.36
1.2
1.17
1.4
1.13
1.02
1.32
1.02
0.9
0.77
0.88

LT. PURPLE
DK. YELLOW
DK. BLUE
YELLOW
RED
BLACK
DK. PURPLE
DK. GREEN
GRAY
WHITE
GRAY/RED

RATED
DEFLECTION COLOR CODE
(IN)
1.02
BLACK
1.32

DK. PURPLE

1.02

DK. GREEN

0.9

GRAY

0.77
0.88

WHITE
GRAY / RED

JCI PART
NUMBER

5/8"

1/2"
029 25334 002

H"

029 25334 003


029 25334 004
029 25334 005
029 25334 006

JCI PART
NUMBER

C"

T"
029
029
029
029
029
029
029

25334
25334
25334
25334
25334
25334
25334

008
007
009
010
011
012
013

B"

W"
LD13759

MOUNT

CHES, INTERPRET
PER ANSI Y14.
TYPE
W
D
G-POWDER COATED, SPRING-POWDER COATED (COLOR: SEE TABLE),
PLATE.
CP
3
5/8
OLTING OR ANCHORING MOUNT TO SUPPORT STRUCTURE WITH A MIN (2)
A CONCRETE ANCHORS.
C2P
3
5/8
D FOR 50% OVER-TRAVEL.
STALLATION INSTRUCTIONS.

D
5/8
5/8

L"

D"

DIMENSION DATA (INCHES)


L

7-3/4

6-1/2

4-3/4

1/2

5-5/8

10-1/2

9-1/4

7-3/4

9/16

DIMENSIONAL
DATA (INCHES)
RATED CAPACITY
(For units with all load
L
B less C
T lbs (810kg)
H
points
than 1785
7-3/4
6-1/2
4-3/4
1/2
5-5/8
*lbs
*kg
10-1/2
9-1/4
7-3/4
9/16
6

VENDOR P/N

COLOR

YORK P/N

Up to 434

Up to 197

CP-1D-510

BLACK

029-25334-002

435 through 765

198 through 347

CP-1D-900

DK GREEN

029-25334-003

766 through 1020

348 through 463

CP-1D-1200

GRAY

029-25334-004

1021 through 1156

464 through 524

CP-1D-1360

WHITE

029-25334-005

1157 through 1785

525 through 810

CP-1D-1785N

GRAY/RED

029-25334-006

Up through 1148

Up through 521

C2P-1D-1350

DK PURPLE

029-25334-008

1149 through 1530

522 through 694

C2P-1D-1800

DK GREEN

029-25334-009

1531 through 2040

695 through 925

C2P-1D-2400

GRAY

029-25334-010

2041 through 2312

926 through 1049

C2P-1D-2720

WHITE

029-25334-012

2313 through 3570

1050 through 1619

C2P-1D-3570N

GRAY/RED

029-25334-013

* Value is de-rated by 15%


Note: Isolators with 1 deflection (Pin 54 = 1) must be of the same class for the entire unit. IE. Must use C2Ps at all locations on a selected
unit, or all CPs
Notes:
1. All dimensions are in inches per ANSI Y14.
2. Standard finish: Housing - Powder coated.
Spring - Powder coated. (Color: see Table)
Hardware - Zinc electroplate
3. Installation requires bolting or anchoring mount to support structure with a min. (2) 5/8" dia. bolt or (2) 1/2" dia. concrete anchors.
4. All springs are designed for 50 % over-travel.
5. Refer to next page for Installation Instructions.

164

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

One Inch Deflection Spring Isolators Installation Instructions


Units shipped on or after June 15, 2008
1. Read instructions in their entirety before beginning
installation.
2. Isolators are shipped fully assembled and are to be
positioned in accordance with the submittal drawings or as otherwise recommended.
3. Set isolators on floor, housekeeping pad or sub-base,
ensuring that all isolator centerlines match the equipment mounting holes. The VMC group recommends
that the isolator base (B) be installed on a level
surface. Shim or grout as required, leveling all isolator bases to the same elevation (1/4-inch maximum
difference can be tolerated).
4. Bolt or anchor all isolators to supporting structure
utilizing base slotted holes (C).

JOHNSON CONTROLS

5. Place equipment on top of isolators making sure


that mounting holes of the equipment line up with
isolator positioning pin (H).
6. The adjustment process can only begin after the
equipment or machine is at its full operating
weight.
7. Adjust each isolator in sequence by turning spring
adjusting bolt (D) one full counterclockwise turn
at a time. Repeat this procedure on all isolators, one
at a time.
8. Continue adjusting each isolator until a minimum
of 1/4" clearance is achieved between the lower
housing and upper housing. (See drawing below).
9. Fine adjust isolators to level equipment.
10. Installation is complete.

165

TECHNICAL DATA

FORM 201.23-NM1 (910)

Durulene Isolator Cross-reference


Units shipped on or after June 15, 2008

RATED
ATED
PACITY DEFLECTION DURO ( 5)
LBS]
[IN]

35
45
70
120

0.4
0.4
0.4
0.4

30
40
50
60

RATED
RATED
PACITY DEFLECTION DURO ( 5)
LBS]
[IN]
135
170
240
380
550

0.5
0.5
0.5
0.5
0.5

0.5
0.5
0.5
0.5

40
50
60
70

0.5
0.5
0.5
0.5
0.5

MOLDED
DURULENE
HF

n AD THRU

TYP 2 PLACES
JCI PART
NUMBER

BT

029 25335 001

ATED
RATED
PACITY DEFLECTION DURO ( 5)
[IN]
LBS]

500
250
000
000
000

CD

JCI PART
NUMBER

30
40
50
60
70

RATED
ATED
PACITY DEFLECTION DURO ( 5)
LBS]
[IN]

250
525
750
100

DW

JCI PART
NUMBER

40
50
60
70
80

AL

JCI PART
NUMBER

L
LD13760

029 25335 002


029 25335 004

dimension data (inches)

mount

RE IN INCHES, INTERPRET PER ANSI Y14.


type
l
w
hf
al
FOR INSTALLATION
INSTRUCTIONS.
WEATHER RESISTANT DURULENE COMPOUND AS STANDARD. ALSO AVAILABLE IN OTHER MATERIALS
RUBBER, EXTREME
HIGH TEMPERATURE
SILICONE, HIGH-DAMPED
NITRILE, AND EPDM.
RD1-WR
3.13
1.75 SILICONE,1.25
2.38
LE CENTER TO CENTER SPACING.
OF MOUNT, PRIOR
TO LOADING. OPERATING
THE
RD2-WR
3.88HEIGHT CALCULATED
2.38 BY THE FREE
1.75HEIGHT LESS 3.00
N UNDER LOAD. ALL DIMENSIONS FOR REFERENCE ONLY
LECTROPLATED RD3-WR
5.50
3.38
2.88
4.13

DIMENSIONAL DATA [INCHES]

W
1.75
2.38
3.38
4.63

RD4-WR

HF
AL
1.25
2.38
1.75
3.00
2.88
4.13
* WEIGHT
2.75
5.00

6.25

AD
0.34
0.34
0.56
RANGE
0.56

BT
0.19
0.22
0.25
(LBS)
0.38

4.63

2.75

5.00

CD
DW
5/16-18 UNC X 3/4
1.25
3/8-16 UNC X 1
1.75
UNC X 1 RANGE2.50
*1/2-13
WEIGHT
(KGS)
1/2-13 UNC X 1
3.00

ad

bt

cd

dw

0.34

0.19

5/16-18 UNC X 3/4

1.25

0.34

0.22

3/8-16 UNC X 1

1.75

0.56

0.25

1/2-13 UNC X 1

2.50

0.56

0.38

1/2-13 UNC X 1

3.00

VENDOR P/N

COLOR

YORK P/N

Up to 374

RD-3 CHARCOAL-WR

CHARCOAL

029-25335-001

826 through 1688

375 through 766

RD-4 BRICK RED-WR

BRICK RED

029-25335-002

1689 through 4000

767 through1814

RD-4 CHARCOAL-WR

CHARCOAL

029-25335-004

Up to 825

* Value is de-rated by 25%


Notes:
1. All dimensions are in inches per ANSI Y14.
2. Refer to next page for Installation Instructions.
3. Mount molded in weather resistant durulene compound as standard; also available in other materials such as natural rubber, extreme high
temperature silicone, high-damped silicone, nitrile and EDPM.
4. AL = Mounting hole center to center spacing.
5. HF = Free height of mount, prior to loading. Operating height calculated by the free height less the static deflection under load. All dimensions for reference only.
6. Hardware - Zinc electroplate.

166

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Installation of Durulene Vibration Isolators


Units shipped on or after June 15, 2008
1. Read instructions in their entirety before beginning
installation.
2. Isolators are shipped fully assembled and are to be
positioned in accordance with the submittal drawings or as otherwise recommended.
3. Set isolators on floor, housekeeping pad, or subbase, ensuring that all isolator centerlines match the
equipment mounting holes. The VMC group recommends that the isolator base (A) be installed on
a level surface. Shim or grout as required, leveling

all isolator bases to the same elevation (1/32-inch


maximum difference can be tolerated).
4. Bolt or anchor all isolators to supporting structure
utilizing base thru holes (B).
5. Remove top bolt and top washer. Place equipment
on top of isolators so that mounting holes in equipment or base line up with threaded hole (C).
6. Reinstall top bolt and washer and tighten down.
7. Installation is complete.

TOP BOLT
("B")
D

TOP WASHER

D
("C")

CL

("B")

CL
SECTION D-D

("A")
LD13762B

JOHNSON CONTROLS

167

TECHNICAL DATA

FORM 201.23-NM1 (910)

Seismic Isolator Cross-reference


Units shipped on or after June 15, 2008

Y2RS
1-1/8"

5"
5/8"

2-3/4"

2-3/4"
12"

3/8" GAP

5/8-11UNC
TYP. (4)

3/4"
TYP.(4)

3/4"
7/8"

14"

1/2" LIMIT
STOP &
NUT
8-3/8"
OPER.
HEIGHT

12-1/4"

3-1/2"

3/8"
LD13761A

5"

NOTES:
1. ALL DIMENSIONS ARE IN INCHES, INTERPRET PER ANSI Y14.
2. STANDARD FINISH: HOUSING-POWDER COATED (COLOR:BLACK), SPRING-POWDER COATED (COLOR: SEE T
WEIGHT RANGE (LBS)HARDWARE
* WEIGHT
RANGE (KGS)
VENDOR P/N
COLOR
YORK P/N
ZINC-ELECTROPLATE.
3.
EQUIPMENT
MUST
BE
BOLTED
OR
WELDED
TO
THE
TOP
PLATE
TO
MEET
ALLOWABLE
SEISMIC
RATINGS.
Up to 391
Up to 177
Y2RSI-2D-460
GREEN
029-25336-006
4. ALL SPRINGS ARE DESIGNED FOR 50% OVERLOAD CAPACITY WITH EXCEPTION OF THE 2D-3280N & 2D-2870
PAGE
FOR274
INSTALLATION Y2RSI-2D-710
INSTRUCTIONS.
392 through 604 5. REFER TO178
through
DK BROWN
029-25336-008
6. CONSULT FACTORY FOR CONCRETE INSTALLATION.

605 through 740

275 through 336

Y2RSI-2D-870

RED

029-25336-009

741 through 1020

337 through 463

Y2RSI-2D-1200N

RED/BLACK

029-25336-010

1021 through 1437

464 through 652

Y2RSI-2D-1690

PINK

029-25336-011

1438 through 2244

653 through 1018

Y2RSI-2D-2640N

PINK/GRAY

029-25336-012

2245 through 2618

1019 through 1188

Y2RSI-2D-2870N

PINK/GRAY/ORANGE

029-25336-013

2619 through 3740

1189 through 1696

Y2RSI-2D-3280N

PINK/GRAY/DK BROWN

029-25336-014

* Value is de-rated by 15%


Notes:
1. All dimensions are in inches, interpret per ANSI Y14.
2. Standard finish: housing-powder coated (color, black), spring-powder coated (color, see table above) hardware - zinc-electroplate.
3. Equipment must be bolted or welded to the top plate to meet allowable seismic ratings.
4. All springs are designed for 50% overload capacity with exception of the 2D-3280N and 2D-2870.
5. Refer to next page for installation instructions.
6. Consult factory for concrete installation.

168

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Seismic Isolator Installation and Adjustment


Units shipped on or after June 15, 2008
1. Read instructions in their entirety before beginning
installation.
2. Isolators are shipped fully assembled and are to be
positioned in accordance with the submittal drawings or as otherwise recommended.
3. Set isolators on floor, housekeeping pad, or sub-base,
ensuring that all isolator centerlines match the equipment mounting holes. The VMC group recommends
that the isolator base plates (B) be installed on a
level surface. Shim or grout as required, leveling all
isolator base plates to the same elevation (1/4-inch
maximum difference can be tolerated).
4. Bolt or anchor all isolators to supporting structure
utilizing base plate thru holes (C) or weld base
plate to supporting structure with 3/8 fillet weld
2" long @ 4" on center around entire base plate or
as engineered for specific load and or field conditions.
5. Isolators are shipped to the job site with (2) removable spacer shims (E) between the top plate and
the housing. These shims must be in place when the
equipment is positioned over the isolators.
6. With all shims (E) in place, position equipment
on top of plate (A) of isolator. Bolt equipment
securely to top plate of isolator using a minimum
of (2) 5/8 UNC A325 grade 5 SAE bolts or weld

("A")

("E")

CL

("G")

("E")

equipment or bracket to the top plate (A) of isolator with a minimum of 3/8 fillet welds 2" long @
3" on center for a minimum total weld of 10". (All
sides of equipment or bracket resting on top plate
(A) must be welded).
7. The adjustment process can only begin after the
equipment or machine is at its full operating
weight.
8. Back off each of the (4) limit stop lock nuts (F)
on isolators 1/2".
9. Adjust each isolator in sequence by turning spring
adjusting nuts (G) one full clockwise turn at a
time. Repeat this procedure on all isolators, one at
a time. Check the limit stop lock nuts (F) periodically to ensure that clearance between the washer
and rubber grommet is maintained. Stop adjustment
of isolator only when the top plate (A) has risen
just above the shim (E).
10. Remove all spacer shims (E).
11. Fine adjust isolators to level equipment.
12. Adjust all limit stop lock nuts (F) per isolator,
maintaining 1/4-to 3/8-inch gap. The limit stop
nuts must be kept at this gap to ensure uniform bolt
loading during uplift (as the case when equipment
is drained).
13. Installation is complete.

GROMMET

("A")

1/4 - 3/8 GAP

WASHER

CL
EQUIPMENT

("F")

("E")

("F")

("C")
("B")

("C")

LD13763B

JOHNSON CONTROLS

169

TECHNICAL DATA

FORM 201.23-NM1 (910)

SLRS Seismic Isolator Specifications


Units shipped before June 15, 2008
D-Tap
- 4 Holes
unless
"D" Tap
4 Holes
unless
otherwise
requested.
otherwise requested

Vertical Limit
Stops-Out of
Vertical Limit Stops-Out
contact
during
of contact during normal
normal
operation
operation.

E
E
E
E

E
E
E
E

H
MBD -Max
MDB - Max Bolt
Bolt
Diameter
Diameter

Rubber
Rubber Snubbing
Collar

T
T

Snubbing
Collar

HCL
HCL
LL

HCW
HCW
W
W

Adjustment Bolt
Adjustment
Bolt

Non-skidNeoprene
Neoprene Pad
Non-Skid
PadInternal
Neoprene - Pad can be removed if
Lower
Internal
Lower
Pad
can
be
removed
if
Enclosed
Steel
Enclosed
Acoustical Pad
Restraining
Neoprene
mounts are welded into
Restraining
Housing
mounts
are
welded
Steel
Nut
position.
Acoustical into position.
Nut
Housing
Pad

LD10509

PIN 54 = S
*Weight Range (lbs)

*Weight Range (kg)

Vendor P/N

COLOR

YORK P/N

UP TO 358 LBS

Up to 162 kg

SLRS-2-C2-420

Red

029-24585-006

358-442 LBS

162 to 201 kg

SLRS-2-C2-520

White

029-24585-007

443-581 LBS

201 to 264 kg

SLRS-2-C2-660

Black

029-24585-008

582-782 LBS

264 to 335 kg

SLRS-2-C2-920

Blue

029-24585-009

783-1037 LBS

335 to 471 kg

SLRS-2-C2-1220

Green

029-24585-010

1038-1496 LBS

471 to 679 kg

SLRS-2-C2-1760

Gray

029-24585-011

1497-2057 LBS

679 to 933 kg

SLRS-2-C2-2420

Silver

029-24585-012

2058-2618 LBS

933 to 1188 kg

SLRS-2-C2-3080

Gray w/ Red

029-24585-013

2619-3179 LBS

1188 to 1442 kg

SLRS-2-C2-3740

Silver w/ Red

029-24585-014

* Value is de-rated by 15%


Notes: I llustration above shows a SLRS-4-C2 (4 Springs). SLRS-8-2 and C2 have one spring, and SLRS-2-C2 has two springs.
SLRS-6-C2 has six springs and SLRS-9-C2 has nine springs.

170

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SLRS Seismic Isolator Installation and Adjustment


Units shipped before June 15, 2008
To Install and Adjust Mounts
1. Supports for mountings must be leveled to installation's acceptable tolerances.
2. Mountings not subjected to seismic or wind forces
do not require bolting to supports.
3. Mountings subjected to seismic or wind forces must
be bolted or welded in position.
4. If mountings are welded in position, remove lower
friction pad before welding.
5. Set mountings with top channels held in place by
the lower restraining nuts and limit stops.
6. Place equipment on mountings and secure by bolting
or welding.
7. Hold lower restraining nut in place and turn vertical
limit stop bolt counter-clockwise until there is a 1/8"
gap between the bolt head and the steel washer.

8. Turn adjustment bolt 8 turns on each mount.


9. Take one additional complete turn on each adjustment bolt in sequence until the top plate lifts off of
the lower restraining nuts. Take no additional turns
on that mount. Continue with equal turns on the
other mounts until the top plates lift off of the lower
restraining nuts of all mounts.
10. Hold the limit stop bolt in place and turn the lower
restraining nut clockwise and tighten it against
the stanchion. Repeat the same procedure on all
mounts.
11. Top plate should remain at a fixed elevation, plus
or minus 1/8".

"D" Tap - 4 Holes unless


otherwise requested
Vertical Limit
Stops-Out of
contact during
normal operation

Rubber
Snubbing
Collar

LIMIT STOP
BOLT

MBD -Max
Bolt
Diameter

1/8"
LOWER
RESTRAINING
BOLTS

1/4"

Adjustment
Bolt
Lower
Restraining
Nut

Non-Skid Neoprene PadInternal


Enclosed Neoprene Pad can be removed if
mounts are welded
Steel
Acoustical into position.
Housing
Pad

SHIPPED & INSTALLED

AFTER ADJUSTMENT

LD10568

JOHNSON CONTROLS

171

TECHNICAL DATA

FORM 201.23-NM1 (910)

ND-X Neoprene Isolator Specifications


Units shipped before June 15, 2008
CS
CapCap
Screw
"CS"
Screw

DD
MBD Maxium

Steel Plate - Top &

Bolt Diameter
"MBD"
Max. Bolt Dia.

SteelBottom.
PlateNeoprene
- Top &
Bottom
Neoprene
covered
to prevent
covered to prevent
corosion.
corrosion

BC
BC

H
H
W
W

LL

TT

LD10569

ENGLISH
SIZE

BC

CS

MBD

ND-C

2-9/16

2-3/4

5-1/2

1/4

2-5/16

4-1/8

1/2-13x1"

1/2"

ND-D

3-3/8

2-3/4

6-1/4

5/16

1/2-13x1"

1/2"

ND-DS

3-3/8

2-3/4

6-1/4

5/16

1/2-13x1"

1/2"

SI
ND-C

65.1

69.9

139.7

6.4

58.7

101.9

1/2-13x1"

13

ND-D

85.7

69.9

158.8

7.9

101.6

127.0

1/2-13x1"

13

ND-DS

85.7

69.9

158.8

7.9

101.6

127.0

1/2-13x1"

13

PIN 54 = N
**Weight Range (lbs)

**Weight Range (kg)

COLOR

YORK P/N

YORK P/N

UP TO 751 LBS

Up to 341 kg

ND-C

Yellow

029-24584-001

751-1651 LBS

341 to 749 kg

ND-D

Yellow

029-24584-002

1651-3226 LBS

749 to 1463 kg

ND-E

Yellow

029-24584-003

** Value is de-rated by 15%

Installation of Neoprene Mounts

It is not necessary to bolt the mountings to a concrete


pad in most cases. Mountings should always be bolted
to the chiller rails. When mountings and the chiller are
installed on steel framing above the ground, the mountings should be bolted to the steel framework. Lower
172

the chiller on to the mountings evenly to avoid placing


excessive weight on individual isolators.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

CIP 1" Deflection Restrained Mounting Specifications


Units shipped before June 15, 2008

6
LD10576

PIN 54 = 1 (See note below)


For Units With All Load Points Less than 1404 LBS (637 KG)
*Weight Range (lbs)

*Weight Range
(kg)

Vendor P/N

Color

YORK P/N

239-384 LBS

108 to 174 kg

CIP-B-450

Red

029-24583-002

384-639 LBS

174 to 290 kg

CIP-B-750

White

029-24583-003

639-851 LBS

290 to 386 kg

CIP-B-1000

Blue

029-24583-004

851-1064 LBS

386 to 483 kg

CIP-B-1250

Gray

029-24583-005

1064-1404 LBS

483 to 637 kg

CIP-B-1650

Black

029-24583-006

For Units With Any Load Point Above 1404 LBS (637 KG)
UP TO 851 LBS

Up to 386 kg

CIP-C-1000

Black

029-24583-007

851-1149 LBS

386 to 521 kg

CIP-C-1350

Yellow

029-24583-008

1149-1489 LBS

521 to 675 kg

CIP-C-1750

Black w/ Red

029-24583-009

1489-1786 LBS

675 to 810 kg

CIP-C-2100

Yellow w/ Red

029-24583-010

1786-2028 LBS

810 to 920 kg

CIP-C-2385

Yellow w/ Green

029-24583-011

2028-2254 LBS

920 to 1022 kg

CIP-C-2650

Red w/ Red

029-24583-012

2354-2936 lbs

1022 to 1332 kg

CIP-C-2935

Red w/ Green

029-24583-013

* Value is de-rated by 15%

JOHNSON CONTROLS

173

TECHNICAL DATA

FORM 201.23-NM1 (910)

Installation
ofsingle
1" Deflection
Mounts
Illustration shows
spring CIP-B or CIP-C
mount.
Units shipped before June 15, 2008

Mounting may be
operated 1/2" above
Free & Operating
Height.

EQUIPMENT BASE

A
Dowel Pin is 3/8" dia. for
CIP-A & 1/2" thereafter

NOTECIP Mounts are not


to be used in seismic
or wind load
applications.

FERROUS HOUSING
SIDE ACCESS INTERNAL
ADJUSTMENT BOLT
Turn clockwise to load
spring and maintain Free
& Operating Height.

FREE &
OPERATING
HEIGHT

NON-SKID NEOPRENE
L
ACOUSTICAL ISOLATION PAD
(Bolting to floor is not necessary for
indoor applications)

SBC
HCL
MAX BOLT
DIA. - MBD

Slot Width - SW

HCW

All springs have additional


travel to solid equal to 50%
of the rated deflection.

LD10577

BASE PLATE DIMENSIONS

TYPE CIP DIMENSIONS (inches)


Size
CIP-B
CIP-C

A
5 3/ 4
6 5/ 8

Free Min
Ht. Ht.
8 1/4 1/2 2 3/4 7/16 6 1/2 11/2 3 /8 7 1/4 61/8 5 1/4
8 7/8 9/16 3 1/2 7/16 7 1/4 13/4 3/8 7 7/8 63/4 6 3/4
L

W SW

HCL HCW MBD SBC

Casting dimensions may vary 1/8"

1. Floor or steel frame should be level and smooth.

5. Complete piping and fill equipment with water,


refrigerant, etc.

2. For pad installations, isolators do not normally require bolting. If necessary, anchor isolators to floor
through bolt holes in the base plate.

6. Turn leveling bolt of first isolator four full revolutions and proceed to each mount in turn.

Isolators must be bolted to the substructure and the equipment must be


bolted to the isolators when outdoor
equipment is exposed to wind forces.

7. Continue turning leveling bolts until the equipment


is fully supported by all mountings and the equipment is raised free of the spacer blocks or shims.
Remove the blocks or shims.

3. Lubricate the threads of adjusting bolt. Loosen the


hold down bolts to allow for isolator adjustment.
4. Block the equipment 10mm (1/4") higher than the
specified free height of the isolator. To use the isolator as blocking for the equipment, insert a 10mm
(1/4") shim between the upper load plate and vertical
uprights. Lower the equipment on the blocking or
shimmed isolators.
174

8. Turn the leveling bolt of all mountings in either


direction in order to level the installation.
9. Tighten the resilient washer and underside of channel cap plate.
10. Installation is now complete.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Refrigerant flow diagram

OIL COOLER COIL

CONDENSOR COIL

SMV

SMV

FLASH
TANK

OIL
SEPARATOR

COMPRESSOR

EVAPORATOR
RC2

Low Pressure Liquid

Low Pressure Vapor

High Pressure Vapor

Medium Pressure Vapor

High Pressure Liquid

Oil

SMV Stopper Motor Valve


S

Solenoid Valve
Relief Valve
Ball Valve

Angle Stop Valve


Sight Glass

M3S - Air Entering Compressor


R-22 -- Refrigerant Circuit Number
R134a
Economizer (Added to some models)

Filter or Dryer
LD10505

FIG. 21 - refrigerant flow diagram


JOHNSON CONTROLS

175

TECHNICAL DATA

FORM 201.23-NM1 (910)

Process and instrumentation diagram

OIL COOLER COIL

CONDENSOR COIL
Z

AIR
FLOW

DV
HTC
LTC

SMV

FT

DV
LPC

SMV

OS
PS

DV
DIF

COMP

HTR

DV
HPC
HPL
DPF

EVAPORATOR
DV
CHT
LTC

HTR

T
FS

CHILLER WATER
FLOW

SMV
S

DV

SYSTEM COMPONENTS

MAJOR COMPONENTS

MICROPROCESSOR CONTROL FUNCTIONS

STEPPER MOTOR VALVE

COMP COMPRESSOR

CHT

CHILLED LIQUID THERMOSTAT

SOLENOID VALVE

OS

OIL SEPARATOR

DP

DIFFERENTIAL PRESSURE CUTOUT

BALL VALVE

FT

FLASH TANK

DPF

DISCHARGE PRESSURE FAN CONTROL

RELIEF VALVE

MUFFLER

DV

DISPLAY VALUE

STOP VALVE ANGLE, ACCESS

HPL

HIGH PRESSURE LOAD LIMITING

PRESSURE SENSOR

HTC

HIGH TEMPERATURE CUTOUT

TEMPERATURE SENSOR

LPC

LOW PRESSURE CUTOUT

REPLACEABLE CORE FILTER/DRYER

LTC

LOW TEMPERATURE CUTOUT

SIGHT GLASS

HPC

HIGH PRESSURE CUTOUT

FS

FLOW SWITCH (optional)

HTR

HEATER

PS

PRESSURE SWITCH

DIF

DIFFERENTIAL

HTR

ELECTRIC HEATER
PLUG

LD10589A

FIG. 22 - process and instrumentation diagram


176

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations

CHILLER & DISPLAY


ELECTRICAL PANEL
FANS

KEYPAD/DISPLAY
PANEL DOOR

CONDENSER
COIL

FILTER
DRIER
MUFFLERS

COMPRESSOR
LD13121

FIG. 23 - component locations


JOHNSON CONTROLS

177

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)

LD10578

FIG. 24 - control and vsd cabinet components


178

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)

MICROGATEWAY
(OPTIONAL)

CHILLER
CONTROL
BOARD

RELAY BOARD #1

LD10579

OPTIONAL
RELAY BOARD #2
CIRCUIT BREAKER
(Standard Unit will have terminal blocks.Input
power to the chiller will be connected here
(see Figures.-31 and 32)).

FIG. 25 - chiller control board, relay boards, microgateway,


and optional circuit breaker
JOHNSON CONTROLS

179

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)

CHILLER
CONTROL
BOARD

MICROGATEWAY
(OPTIONAL)

CLOCK JUMPER (CLK)


JP2

RELAY BOARD #1

RELAY BOARD #2
RS-232/485 JUMPER

JP4, JP5, & JP6


LD10580

mA

JUMPER POSITION

FIG. 26 - chiller control board, relay boards, and microgateway, 2 Compressor


180

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)

CHILLER
CONTROL
BOARD
RELAY BOARD #3

RELAY BOARD #1

RELAY BOARD #2
MICROGATEWAY
(OPTIONAL)

JP4, JP5, & JP6

50069

mA

JUMPER POSITION

FIG. 27 - chiller control board, relay boards, and microgateway, 3 Compressor


JOHNSON CONTROLS

181

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)


VSD
LOGIC BOARD

SCR TRIGGER BOARD

LD10582

FIG. 28 - VSD LOGIC BOARD


182

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)

R86
(COMPR 4
Over Load Adjust)
R42
(COMPR 3
Over Load Adjust)
R64
(COMPR 2
Over Load Adjust)

YORk

R19
(COMPR 1
Over Load Adjust)

M ADE IN THE USA

LD10590

FIG. 29 - VSD LOGIC BOARD (original - obsolete), P/N 031-02477-000


JOHNSON CONTROLS

183

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)

MADE IN THE USA

R86
(COMPR 4
Over Load Adjust)
R42
(COMPR 3
Over Load Adjust)
R64
(COMPR 2
Over Load Adjust)
R19
(COMPR 1
Over Load Adjust)

LD13119

FIG. 30 - VSD LOGIC BOARD (NEW), P/N 031-02507-XXX


184

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)

10CR FAN PUMP


OPTIONAL CIRCUIT
CONTROL AND
CONTROL RELAY
BREAKER
VSD CABINET
(Standard Unit will
COOLING COIL CONTROL AND
have terminal blocks) FLASH TANK FEED
VSD CABINET
11T
AND DRAIN VALVE
COOLING FAN
TRANSFORMER
CONTROLLER

10T
TRANSFORMER

INCOMING POWER
GROUND LUGS

1TB
TERMINAL
BLOCK

INPUT POWER TO
THE CHILLER CONNECTS
HERE

4-9FU FUSES and


14-16FU FUSES
17-21 FU
FUSES

LD10583

TRANSIENT
SUPPRESSOR

1L AC LINE
INDUCTOR

FIG. 31 - Power components, 2 compressor


JOHNSON CONTROLS

185

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)

OPTIONAL CIRCUIT
BREAKER
(Standard Unit will
have terminal blocks)

11T
TRANSFORMER

FLASH TANK
DRAIN and FEED
VALVE
CONTROLLER
(VG1)

CONTROL AND
VSD CABINET
COOLING COIL

CONTROL AND
VSD CABINET
COOLING FANS

1TB
TERMINAL
BLOCK
(Hidden from
view)

50076

FUSES
FU4, 5, 6, 7, 8 ,9
14, 15, 16, 22, 23, 24
10T
TRANSFORMER

INPUT POWER TO
THE CHILLER CONNECTS
HERE

TRANSIENT
SUPPRESSOR
BOARD
11, 12, 13 FU

FIG. 32 - Power components, 3 compressor


186

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)

FAN CONTACTORS
4CR-9CR

LD10584

3T TRANSFORMER
(24VAC to SCR Gate Driver Board and VSD Logic Board)

FIG. 33 - FAN CONTACTORS AND 3T transformer, 2 COMPRESSOR


JOHNSON CONTROLS

187

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)

FAN
CONTACTORS
(4, 5, 6, 7, 8, 9
11, 12, 13CR)

3T
TRANSFORMER

50072

FIG. 34 - FAN CONTACTORS, 3 COMPRESSOR


188

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)


17-21 FU FUSES
(17 FU: 2T, 18 FU: VSD Logic /
SCR Trigger Board /
Pump Contactor,
19 FU: 10T and 11T,
20 FU: Relay Board #1,
21 FU: Relay Board #2
COOLING
FAN

COOLING
FAN

TRANSIENT
SUPPRESSOR BOARD
(3-Phase Input)
4-9 FU FUSES and
14-16 FU FUSES
(4-6 FU: TB-1-3 SCR
Trigger Board,
7-9 FU: Sys. 1 Fans,
14-16 FU: Sys. 2 Fans)

4-6 CT
CURRENT
TRANSFORMERS
3-8 RES RESISTORS
(Motor Output RC
10 CR FAN PUMP
DV/DT Network)
CONTROL RELAY

LD10585

1L AC LINE
INDUCTOR

3-8 RES RESISTORS


(Motor Output RC
"DV/DT Network)

CAPACITORS C15-C17
(Motor Output RC DV/DT
Network)

FIG. 35 - VSD Components


JOHNSON CONTROLS

189

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)


Cooling
Fan

Cabinet
Cooling
coil

3t
(vsd logic and
SCR Trigger Board
Fan
24 VAC Supply
Contactors Transformer)
4cr-9cr

BUS
ISOLATOR
BOARD
(Feeds VSD
Logic Board)
CURRENT
TRANSFORMERS

SCR
TRIGGER
BOARD

IGBT GATE
DRIVER
BOARDS

SNUBBER
CAPS
(C7-C12)

IGBT
MODULES

SCR/DIODE
MODULES

1L LINE
INDUCTOR

BUS FILTER
CAPACITORS
(Behind Panel)

LD10586

HEATSINK
(Water Cooled)

FIG. 36 - VSD Components, 2 COMPRESSOR


190

1RES and 2RES


BUS CAPACITOR
BANK EQUALIZING/
BLEEDER
RESISTORS
JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)


Cooling
Fan

Cabinet
Cooling
coil

Fan
Contactors
4cr-9cr and
11CR-13 CR)

DC BUS
VOLTAGE
ISOLATION
BOARD

3t
(vsd logic and
SCR Trigger Board
24 VAC Supply
Transformer)

CURRENT
TRANSFORMERS

6
SCR
TRIGGER
BOARD

IBGT GATE
DRIVER
BOARDS

SNUBBER
CAPS
(C7-C12)

IBGT
MODULES

SCR/DIODE
MODULES
BUS FILTER
CAPACITORS
(Behind Panel)

50085

HEATSINK
(Water Cooled)

1RES AND 2RES


BUS CAPACITOR
BANK EQUALIZING/
BLEEDER
RESISTORS

FIG. 37 - VSD Components, 3 COMPRESSOR


JOHNSON CONTROLS

191

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)

cooling
fanS

Cabinet
cooling
coil

CURRENT
TRANSFORMERS
C13-C17

FAN
RELAYS

TRANSIENT
SUPPRESSOR
BOARD
W/ 11FU, 12FU,
and 13 FU FUSES
(3 Phase Input)

10CR FAN
PUMP
CONTROL
RELAY

LD10587

1L LINE
INDUCTOR

FIG. 38 - VSD Components, 2 COMPRESSOR


192

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)


TRANSIENT
SUPPRESSOR
BOARD
W/ 11FU, 12FU,
and 13 FU FUSES
(3 Phase Input)

Cabinet
cooling
coil

CURRENT
TRANSFORMERS
(C14, C13, 12, 9, 8, 7, 6, 5, 4)

cooling
fan

FAN
RELAYS

2
1

2
1

2
1

50073

LINE
INDUCTORS

SNUBBER CAPS
c24, 25, 26, 21
22, 23, 18, 19, 20

SNUBBER RESISTORS 2
res15, 16, 17, 18, 19, 20,
9, 10, 11, 12, 13, 14, 3, 4,
5, 6, 7, 8

FIG. 39 - VSD Components, 3 Compressor


JOHNSON CONTROLS

193

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)

The line inductor will reach operating temperatures of


over 300 F. Do not open panel doors during operation. Assure the inductor is cool whenever working
near the inductor with power OFF.

LD10588

FIG. 40 - Inverter power Components, 2 COMPRESSOR


194

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)


SCR
TRIGGER
BOARD

50077

FIG. 41 - Inverter power Components, 3 COMPRESSOR


JOHNSON CONTROLS

195

TECHNICAL DATA

FORM 201.23-NM1 (910)

Component locations (CONT'D)


IGBT's

IGBT's

IGBT's

SCR/DIODE
MODULES

WATER COOLED
HEAT SINK

SCR/DIODE
MODULE

LD10591

1RES and 2RES BUS CAPACITORS BANK


EQUALIZING/BLEEDER RESISTORS

LAMINATED
BUS
STRUCTURE

IGBT GATE
DRIVER
BOARD #1

IGBT GATE
DRIVER
BOARD #2

LD10592

IGBT's

IGBT's

FIG. 42 - Inverter power Components


196

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Component locations (CONT'D)


LAMINATED
BUS STRUCTURE

IGBT GATE
DRIVER BOARD
BUS FILTER
CAPACITORS

WATER COOLED
HEAT SINK
IGBT

LD10593

IGBT's

IGBT's

SCR/DIODE
MODULES
SCR/DIODE
MODULES

1RES and 2RES BUS CAPACITORS BANK


EQUALIZING/BLEEDER RESISTORS

LD10594

FIG. 42 - Inverter power Components (CONT'D)


JOHNSON CONTROLS

197

TECHNICAL DATA

FORM 201.23-NM1 (910)

Glycol system components


REAR
OF
VSD PANEL

SEE
DETAIL "B"
SEE
DETAIL "C"

DETAIL "A"
TO GLYCOL PUMP
(SEE DETAIL "A")

DETAIL "B"

TYPICAL 4 PLACES

GLYCOL PUMP
(SEE DETAIL "A")

DETAIL "C"
LD13122A

FIG. 43 - glycol pump & fill tube locations


198

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Glycol system components (CONT'D)

GLYCOL
FILL
TUBE

LD10597

FIG. 44 - glycol piping and fill tube location


JOHNSON CONTROLS

199

SUCTION
STRAINER

STATOR

FIG. 45 - compressor components

200
OIL
FILTER

MOTOR
TERMINALS

STATOR
KEY
ROTOR

DISCHARGE
HOUSING

MOTOR/ROTOR
HOUSING

FEMALE
ROTOR

MALE
ROTOR

BEARINGS SHIMS

SHIMS

BEARINGS

TECHNICAL DATA
FORM 201.23-NM1 (910)

Compressor components

LD10596

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

The +/- (PLUS/MINUS) key allows making numeric


values negative.

Chiller electronic components


Keypad
An operator keypad allows complete control of the system from a central location. The keypad offers a multitude of command keys on the left and right side of the
keypad to access displays, program setpoints, history
data, and initiate system commands. Most keys have
multiple displays that can be accessed by repetitively
pressing the key or by pressing the ,,, and
(ARROW) keys. The keypad utilizes an overlay to
convert the keypad to various languages.

The (ENTER) key stores program changes into


memory.
The X (CANCEL) key is used to cancel the data entry operation and returns the programmed value to the
original value, before any programming changes were
made, when an error is made.
The (UP ARROW) and (DOWN ARROW)
keys allow scrolling backward () and forward ()
through items to be programmed under keys such as the
PROGRAM or OPTIONS key.
The (UP ARROW) and (DOWN ARROW) keys
also allow scrolling forward () or backwards ()
through data display keys that have multiple displays
under keys such as UNIT DATA, SYSTEM DATA, HISTORY, PROGRAM, OPTIONS, etc. The arrow keys
can be used instead of repeatedly pressing the data key
to see the multiple displays under a key. Once the
(ARROW) keys are pressed and used for scrolling,
pressing the original data key will return to the first display
message displayed under the data (UNIT DATA,
SYSTEM DATA, etc.) keys.

LD10605

The keypad also contains keys in the center section for


data entry in the various program modes. These keys
are listed below:








0-9 Keys NUMERIC KEYPAD


PERIOD/DECIMAL
+/- PLUS/MINUS
ENTER
CANCEL
UP ARROW
DOWN ARROW
LEFT ARROW
RIGHT ARROW

The numeric keys allow keying numeric values into


memory.
The (PERIOD/DECIMAL) key allows keying a
decimal point into numeric values.

JOHNSON CONTROLS

The (LEFT and RIGHT ARROW) keys allow


scrolling between non-numeric program choices under
the OPTION, DATE/TIME, and SCHEDULE keys.
The (LEFT ARROW) key allows programming the
default value when programming numeric values. For
changing numeric values, the (RIGHT ARROW)
key has no function.
The (ARROW) keys also allow scrolling sideways between the same displays on different systems.
For example, Pressing the (RIGHT ARROW) key
while viewing the system #1 suction pressure moves the
display to system #2 suction pressure.
Pressing the (LEFT ARROW) key moves the
opposite direction. The arrow keys also allow fast
scrolling through data under keys such as HISTORY
by enabling the operator to move between subgroups
of data such as Unit, System, and VSD data.

201

TECHNICAL DATA

FORM 201.23-NM1 (910)

Keypad Data Entry Mode


For numeric programmable items, the data entry mode
is entered by pressing any of the number keys, the decimal point key, or the +/- key. When the data entry
mode is entered, the data from the key press will be
entered and the cursor will appear under the position
where the data is being entered.

DISPLAY

For non-numeric programmable items, data entry


mode is entered by pressing the or (ARROW)
keys. When the data entry mode is entered, the cursor
will appear under the first position of the non-numeric
string. The programmable choice may be changed by
pressing the or (ARROW) keys.
To exit the data entry mode and store the programmed
value, the (ENTER) key must be pressed. When the
(ENTER) key is pressed, the cursor will disappear.
The data entry mode may also be exited by pressing
the X (CANCEL) key. The programmed data will be
returned to its original value when the X (CANCEL)
key is pressed.

LD10605

KEYPAD

UNIT
Switch

Chiller Control Board



When the data entry mode is exited, the cursor will


disappear. If any other key is pressed while in the
Data Entry Mode, the following display will appear
for 2 seconds indicating the user must choose between
accepting or canceling the change:
XXXXXXXXXXX PRESS

TO ACCEPT VALUE OR

X TO CANCEL DATA ENTRY

If the (ENTER) key was pressed from the data entry mode and the numeric value entered was out of
range, the following message will appear for 2 seconds
followed by the original data display.
XXXXXXXXXXX OUT OF RANGE TRY AGAIN!
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

Display
The 80 character (2 lines of 40 characters per line) display is a Liquid Crystal Display (LCD) used for displaying unit parameters, system parameters, and operator messages. The display has an LED backlight
background for night viewing and is viewable in direct
sunlight.

202

LD10606

RTC

The Chiller Control Board is the controller and


master decision maker in the control panel. The onboard microprocessor control is capable of controlling
up to 4 compressors. System inputs from pressure
transducers and temperature sensors are connected
directly to the Chiller Control Board. The Chiller
Control Board circuitry multiplexes all of the analog
inputs, digitizes them, and scans the inputs to keep a
constant watch on chiller operating conditions. Based
on this information, the Chiller Control Board issues

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

commands to the Relay Output Board(s), Drain/Feed


Valve Controller, and VSD Logic Board to activate
and de-activate contactors, solenoids, control valves,
set compressor speeds, etc., for chilled liquid and
safety control. keypad commands are acted upon by
the Chiller Control Board microprocessor to change
setpoints, cutouts, scheduling, operating requirements,
and to provide displays.

RS-485 communications. UART2 is configured for


VSD communications over an internal chiller RS-485
port located within the Control/Power cabinet. UART2
has a higher priority interrupt than UART1. The data
is sent and received at a rate of 9600 baud and serves
only as the communications between the Chiller Control Board and the VSD Logic Board. Both of these
boards are located within the control/power panel.

The Chiller Control Board contains a Real Time Clock


integrated circuit chip with an internal battery backup
of 8K x 8 bit RAM. The purpose of the battery backed
RAM is to assure any programmed values (setpoints,
clock, cutouts, history data etc.) are not lost during
a power failure, regardless of the time involved in a
power outage or shutdown period.

On power-up, the Chiller Control Board will attempt to


initialize communications with the VSD Logic Board.
The Chiller Control Board will request the number of
compressors select and VSD software version. If for
some reason the information is not provided, the request will be made over and over again until it is received. Once the data has been received, the Chiller
Control Board will not ask for it again. If the communications is not established, a VSD Loss Of Comms
fault message will appear on the STATUS display.

The Chiller Control (Microprocessor) Board contains


an onboard power supply, which provides 5VDC regulated to sensors, transducers, display, and other circuit
boards. The supply also provides +12VDC to the Relay
Output Boards and the +34VDC to the level sensors.
The Chiller Control Board is capable of directly
receiving analog inputs from temperature sensors and
transducers. An analog to digital converter (A/D) with
an onboard 4 channel multiplexer (MUX) allows up to
48 analog inputs to be read. The A/D Converter converts the analog signals to digital signals, which can be
read by the onboard microprocessor. On a 2 system
chiller, approximately half of these inputs are utilized.

Two 8 channel, 8 bit Digital to Analog Converters (D/A


Converter) on the Chiller Control Board supply the
Feed and Drain Valve Controller signals to allow the
controller to position the Flash Tank Feed and Drain
Valves. The Feed Valve controls the refrigerant level
in the flash tank while the Drain Valves controls superheat. The control voltage to the Feed and Drain Valve
Controller has a range of 0 to 10.28VDC.
Relay Output Boards

Three integrated circuits on the microprocessor can be


configured for digital inputs or outputs (Digital I/O).
As inputs, they can read digital (2 level, on/off) inputs
like keypad keys, unit switch, high pressure cut-out,
flow switch, etc. As outputs they are used for controls
like turning on fans, controlling compressor heaters,
controlling chiller valves, or other devices requiring
ON/OFF control. Up to 72 Digital I/O will be utilized
to control the chiller.
The Chiller Control (Microprocessor) Board contains
a dual UART (Universal Asynchronous Receiver
Transmitter) for RS-485 and RS-232 communications.
UART1 is configured for RCC and ISN communications on the external chiller RS-485 port. Data is sent
and received at 4800 baud with 1 start bit, 8 data bits,
odd parity, and 1 stop bit. The port is shared with the
RS-232 interface and at start-up will be initialized to

JOHNSON CONTROLS

LD10607

Two or three Relay Output Boards are required to


operate the chiller. These boards convert 0 to 12VDC
logic levels outputs from the Chiller Control Board to
115VAC levels used by contactors, relays, solenoid
valves, etc., to control system and chiller operation.

203

TECHNICAL DATA

FORM 201.23-NM1 (910)

The common side of all relays on the Relay Output


Board is connected to +12VDC.
The open collector outputs of the Chiller Control Board
energize the DC relays on the Relay Output Board by
pulling one side of the relay coil to ground. When
not energized, both sides of the relay coils will be at
+12VDC potential.

The AC incoming line voltage is rectified by the full


three phase semi-converter bridge, made up of three
SCR/Diode modules, which provides pulsating DC to
the DC link Filter in the VSD.
SCR Trigger Board
The SCR Trigger Board controls the firing (gating) sequence of the Bridge SCRs.

VSD (Variable Speed Drive)


The VSD is a liquid cooled, transistorized, PWM
inverter packaged within the Control/Power cabinet.
The inverter is composed of four major sections:
AC to DC rectifier section with precharge circuit.
DC link filter section.
Three phase DC to AC inverter section.
Output RC suppression network.
AC to DC Rectifier
The AC to DC Rectifier circuit utilizes a semi-converter made of three SCR/diode modules in a three phase
bridge configuration. Each SCR/Diode module contains 1 SCR and 1 diode. The modules are mounted on a
liquid cooled heatsink. This circuit rectifies the
incoming AC voltage to unfiltered DC, which is filtered
by the DC Link Filter.

LD10609

Command for the SCR Trigger Board to begin firing


the SCRs is initiated by the VSD Logic Board.
The SCR Trigger Board also monitors the three phase
input voltage to detect the loss of an incoming phase.
DC Link Filter

LD10608

A
semi-converter
(combination
SCR/Diode)
configuration allows utilizing a separate pre-charge
circuit to limit the current in the DC link filter capacitors when the VSD is first switched on. This is accomplished by slowly turning on the SCRs to initially
charge the DC Bus. Once charged, the SCRs remain
fully gated on during normal operation. This configuration also provides a fast disconnect from main power
when the drive is switched off.
When the drive is called to run (leaving chilled liquid
temperature is more than the Setpoint plus CR), the
SCR/Diode modules are turned on by the SCR trigger
Board, allowing the DC link filter capacitors to slowly
precharge for a period of 20 seconds.

204

The DC Link Filter consists of a bank of electrolytic


filter capacitors. The capacitors smooth (filter) ripple
voltage resulting from the AC to DC rectification and
provides an energy reservoir for the DC to AC inverter. The capacitor filter bank is made up of 2 banks of
parallel-connected capacitors wired in series. Series
banks of capacitors allow using smaller sized capacitors with lower voltage ratings.

FILTER
CAPACITORS

LD10610

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

The capacitor bank in conjunction with the 1L Line


Inductor forms a low pass LC Filter and provides further smoothing (filters ripple) to the rectified DC.

1L Line Inductor

Equalizing/Bleeder resistors connected across the


banks equalize the voltage between the top and bottom
capacitors to avoid damaging the capacitors from over
voltage. The Equalizing/Bleeder resistors also provide
a path for discharge of the capacitors when the drive is
switched off. This safely discharges the capacitors in
approximately 5 minutes. Always be careful, a bleeder
resistor could be open and the bus may be charged.
LD10612

1L LINE INDUCTOR

LD10611

EQUALIZING/BLEEDER
RESISTORS

When servicing, always check the DC


Bus Voltage across the top and
bottom, banks of capacitors with a
known functioning voltmeter
correctly set to the proper scale before
performing service on the inverter.
DO NOT rely on the Bleeder Resistors
to discharge the capacitor banks without checking for the purpose of safety.

The 5% impedance 1L Line Inductor has multiple


functions. 1L forms a low pass LC filter that filters the
pulsating DC from the AC to DC converter, to smooth
DC voltage. The inductance eliminates notches on the
incoming AC line. The inductance also helps protect
the SCRs from high voltage incoming line transients,
which could damage them. 1L slows down the rate of
rise of current if an internal short circuit occurs, reducing the potential damage caused by the short. 1L also
reduces the input current total harmonic distortion.
DC to AC Inverter
The DC to AC Inverter section converts the rectified
and filtered DC back to AC at the equivalent magnitude and frequency to run a compressor at a specific
speed. Although a common DC Bus links the compressor drive outputs, each compressor has its own
inverter output module. Each inverter output module
consists of 6 IGBTs (3 modules) and an IGBT Gate
Driver Board, which converts DC to a 3 - phase AC
output. The IGBTs are mounted to the liquid cooled
heatsink designed to take the heat away from the devices and remove it in the condenser. The IGBT Gate
Driver Board provides gating pulses to turn the IGBTs
ON and OFF.

NEVER short out a capacitor bank


to discharge it during servicing. If
a bleeder resistor is open and a capacitor bank will not discharge, immediately contact Johnson Controls
Product Technical Support.

LD10613

IGBT's
JOHNSON CONTROLS

IGBT's
205

TECHNICAL DATA

FORM 201.23-NM1 (910)

Laminated Bus Structure


The Laminated Bus Structure is a group of copper
plates sandwiched together that connects the SCR/Diode Modules, Bus Filter Capacitors, and IGBTs. The
purpose of the Laminated Bus Structure is to reduce
the inductance that would be present in wiring or bus
bars often used to connect high voltage components in
VSDs. Removing inductance in the circuit reduces
the voltage spike that occurs when the IGBTs turn
off. These voltage spikes can potentially damage the
IGBTs.
RTC

LAMINATED BUS
STRUCTURE

LD13120

fig. 46 - NEW BOARD P/N 031-02507-000

The VSD Logic Board contains an FPGA


(Field Programmable Gate Array) which handles the
hardware safeties and can shut down the VSD much
faster than the software safeties, since they are not
dependent upon running program loops in software.
The VSD handles all VSD related safeties including
high motor current, overload, DC Bus voltage faults,
etc.
LD10614

VSD Logic Board


The VSD Logic Board controls VSD functions/
operations and communicates through a serial communications line with the Chiller Control Board. Safety
and shutdown information stored in the RTC (Battery
backed RAM) is reported back to the Chiller Control
Board via the communications link. The VSD Logic
Board converts the speed and run commands from
the Chiller Control Board into the necessary voltage
and frequency commands to operate the inverter section. The VSD Logic Board also controls the converter
section of the VSD (AC to DC conversion) by
controlling the pre-charge function.
The VSD Logic Board contains a second microprocessor for motor control, which generates the PWM signals that control the IGBTs in the inverter section of
the VSD.

206

RTC

LD10615

fig. 47 - OBSOLETE BOARD P/N 031-02477-000

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Inputs to the VSD Logic Board are fed through an


onboard multiplexer (MUX) before being sent to the
A/D converter. These signals allow the VSD Logic
Board to monitor DC Bus voltages, compressor motor currents, VSD internal ambient temperature, IGBT
baseplate temperatures, and compressor overload settings.
The VSD Logic Board controls the glycol pump and
the cabinet cooling fans. Details on the controls are
provided in the VSD Operation and Controls section,
Page 233.
Control Panel to VSD Communications
Communication between the VSD Logic Board and
the Chiller Control Board is made via a three-wire
RS-485 opto-coupled data link. Communications
between the two boards occurs at the rate of 9600
baud. UART2 of the dual UART located on the
Chiller Control Board is dedicated to internal communications and has a higher priority interrupt than
the external communications UART1. The Chiller
Control Board will control VSD start/stop, selection of which compressors to run, and compressor
speed. The VSD Logic Board will run the desired
compressors at the speed requested by the Chiller
Control Board. The VSD will report back to the Chiller Control Board, shutdown and safety information
related to internal VSD operation and the compressor
motors.
On power-up, the control panel will attempt to initialize communications with the VSD. The Chiller Control Board will request initialization data from the VSD
Logic Board. The initialization data required is the
number of compressors and the VSD software version.
Once these data points have been received by the control panel, the unit has successfully initialized and will
not request them again.
If the Chiller Control Board does not receive
initialization data from the VSD Logic Board in
8 seconds or loses communications with the VSD
for 8 seconds at any time, the chiller will fault on a
communications failure. The Chiller Control Board
will continue to send messages to the VSD Logic
Board in an attempt to establish communications while
the chiller is faulted.

JOHNSON CONTROLS

The VSD Logic Board will also monitor a


communications loss. If the VSD Logic Board loses
communications with the Chiller Microprocessor
Board for 8 seconds at any time, the VSD will shut
off all compressors and wait for valid comms from the
Chiller Control Board.
Once communications is established, the Chiller Control Board will send a data packet on the data link once
every second at 9600 baud. This data packet will include run, stop, and speed commands as well as request
operating data from the VSD. Operating data returned
by the VSD will include individual motor currents,
motor %FLAs, output frequency, compressor motor
temperature, and fault information related to internal
VSD operating parameters such as DC Bus voltage,
IGBT baseplate temperatures, VSD internal ambient,
pre-charge relay status, power supply status, run relay
status, motor overload, and supply single phase. The
Chiller Control Board will poll the VSD Logic Board
for information continuously while the chiller is running.
IGBT Gate Driver Boards

LD10613

The IGBT Gate Driver Boards provide the ON and


OFF gating pulses to the IGBTs. The gating signals
originate from the VSD Logic Board and are changed
in level by the IGBT Gate Driver Board. The IGBTs
in the inverter section of the VSD, change the DC Link
voltage to a variable Voltage and Frequency output to
the motor, to control the compressor motor speed. The
IGBT Gate Driver Boards also provides VCE SAT detection (short circuit detection) to safely turn off the
IGBTs during a short circuit condition. When a short
circuit occurs, the voltage (VCE SAT) across the IGBT
increases as a result of the high current. The IGBT
Gate Driver Board is an integral part of the IGBT assembly for each compressor.

207

TECHNICAL DATA

FORM 201.23-NM1 (910)

Current Transformers

Flash Tank Feed and Drain Valve Controller

LD10617
LD10619

CURRENT
TRANSFORMERS

A current transformer on each phase sends current signals proportional to phase current to the VSD Logic
Board. The output of each CT is buffered, scaled, and
sent to RMS to DC converters. These signals are then
sent to an A-D converter, scaled, and sent to the Chiller
Control Board for current display and current limiting
control.
The highest current is also compared to the setting of
the Overload Adjustment Potentiometer on the VSD
Logic Board for overload safety sensing.
DV/DT Output Suppression Network

The Flash Tank Feed and Drain Valve Controller is a


microprocessor driven controller that operates the Feed
and Drain Valves based on commands from the Chiller
Control Board. The Feed and Drain Valves control the
level of liquid in the flash tank and the superheat to
the evaporator. The controller is a stand-alone valve
control module in the Control/VSD panel. The flash
tank liquid level is controlled by sequencing a stepper
motor valve (Feed Valve) on the inlet of the flash tank.
The controller opens and closes the Feed Valve to control the liquid level of the refrigerant in the flash tank
based on commands from the Chiller Control Board.
Superheat is controlled by sequencing a stepper motor
valve (Drain Valve) on the outlet of the flash tank. The
controller opens and closes the Drain Valve to control
flow to the evaporator and ultimately superheat to the
compressor based on commands from the Chiller Control Board.
Drain Valve superheat control is controlled by a PI control algorithm based on suction pressure and suction
temperature in the Chiller Control Board software.

LD10618

DV/DT
RESISTORS

DV/DT
CAPACITORS

The dV/dT Output Suppression Network limits the rate


of rise of voltage and the peak voltage of the PWM
pulses applied to the motor windings. This eliminates
the possibility of causing a turn-to-turn short in the motor due to winding insulation breakdown. The suppression network is made up of a 3-phase RC network.
208

The control algorithms will attempt to control the level


in the flash tank to approx 35% when the economizer is
energized. If the level exceeds 87.5%, the system will
fault. The normal 35% level may fluctuate appreciably when the economizer is off as the flash tank acts
as nothing more than a reservoir as the Drain Valve
controls superheat. The level will also vary when the
economizer is first energized or a system transient occurs such as fan cycling, etc.
The controller is typically located in the back of the
panel behind the power wiring terminal block/circuit
breaker or on the wall of the panel on the left side of
the cabinet.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

CHILLER CONFIGURATION JUMPERS

DC Bus Voltage Isolation Board

There are a number of chiller configuration jumpers


that are factory wired into wire harnesses or plugs.
These jumpers typically never need to be reviewed unless in some unlikely situation, a chiller is incorrectly
configured or a loose connection occurs.
Number of Compressors Configuration
Jumper
LD10620

The DC Bus Isolation Board allows the VSD Logic


Board to read the voltage on the DC BUS without
exposing the VSD Logic Board to the high voltage.
Instead, the DC Bus Isolation Board contains a resistor network that forms voltage dividers with resistors
on the VSD Logic Board, which steps down the voltages so that scaled down voltages proportional to the
full and 1/2 bus voltages can be safely fed to the VSD
Logic Board. The DC Bus Isolation Board supplies 3
connections to the VSD Logic Board; plus bus, minus
bus and half bus.
Chiller Circuit Breaker

Software packs (EPROMs) are common between 2, 3


and 4 compressor chillers. As a result, the VSD Logic
Board must be configured for the actual number of compressors. The chiller is configured for the number compressors through the use of jumpers, factory plugged
into the J1 plug on the VSD Logic Board. This hard
wiring configures the VSD Logic Board for the
number of compressors on the chiller, avoiding
mis-programming. The jumpers are only checked
at power-up. If no jumpers are sensed, or an invalid
combination is sensed and communicated to the Chiller Control Board, start-up of the unit will be inhibited
and an INVALID NUMBER OF COMPRESSORS
SELECTED warning message will be displayed in
the Status display.
TABLE 1 shows the chiller number of compressors
and the associated location of the jumpers to program
the appropriate compressor configuration.
TABLE 1 - C
 OMPRESSORS AND THE
APPROPRIATE JUMPER POSITIONS

LD10623

# of

VSD LOGIC BOARD

COMPRESSORS

JUMPER POSITION

J1-10 to J1-9

J1-11 to J1-9

J1-12 to J1-9

An Optional Circuit Breaker may be supplied on the


input of the system. The incoming power will be fed
to the terminals on the circuit breaker. If the Circuit
Breaker Option is not selected, incoming power will
be fed to terminal blocks. The breaker also provides
ground fault protection. 2 and 3 compressor chillers
utilize one circuit breaker, while 4 compressor chillers
utilize 2 breakers.

JOHNSON CONTROLS

209

TECHNICAL DATA

FORM 201.23-NM1 (910)

VSD Logic to Chiller Microprocessor


Board RS-485 Communication
Configuration Jumpers
The Chiller Control Board and the VSD Logic
Boards communicate over an RS-485 link. The
communications link requires a matching address
to be set up at both ends. The VSD Logic Board
communications bus is configured through the use of
jumpers, factory plugged into the J5 plug on the VSD
Logic Board. The VSD Logic Board will only check
the jumper positions once at power-up.
TABLE 2 shows the VSD Logic Board Address
configuration and the associated location of the jumpers. The jumpers will vary according to the number of
VSD Logic Boards installed. All chillers utilize a single VSD Logic Board and will use VSD Logic Board
Address 1.
TABLE 2 - V
 SD logic board address jumper
VSD LOGIC BOARD's

VSD LOGIC BOARD

ADDRESS

JUMPER POSITION

Maximum VSD Frequency/Model


designator
The model number of the chiller determines the maximum VSD frequency at 100% full speed. The maximum frequency is programmed by factory installed
jumpers on the J7 plug of the Chiller Control Board.
Three digital inputs determine a binary code, which
determines the maximum frequency. The inputs are
read as a 0 or low when a jumper is out or a 1 or high
when the wire jumper is inserted between the two pins.
The jumpers will only be checked once by the Chiller
Control Board on power-up.
TABLE 3 shows the Chiller configuration and the
associated location of the jumpers.
TABLE 3 - maximum frequency / Model
designator jumper
CHILLER CONTROL
BOARD MAX.
VSD
FREQUENCY

J7-1
to
J7-2

J7-3
to
J7-4

J7-5
to
J7-6

YCIV
0600 SA/PA,
0630 EA/VA,
0720 SA/PA,
0840 SA/PA,
0830 EA/VA,
0920 SA/PA,
0930 EA/VA,
1000 SA/PA,
1340 SA/PA,
1500 SA/PA

J5-1 to J5-2
1

and
J5-3 to J5-4

210

J5-3 to J5-4

J5-1 to J5-2

NONE

200 Hz

196 Hz

1
0700 EA/VA,
0800 EA/VA,
1220 EA/VA,
1380 EA/VA

192 Hz

188 Hz

1180 SA/PA

186 Hz

0770 SA/PA,
0590 EA/VA,
1070 SA/PA

182 Hz

0650 SA/PA,
0760 EA/VA,
1050 EA/VA

178Hz

1120 EA/VA

178 Hz (Spare)

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SECTION 7 - OPERATION
Operating controls
Anti-recycle Timer
A typical 5 or 10 minute anti-recycle timer is not
necessary to allow compressor motor cooling, due to
the VSDs ability to provide a low current inrush start.
The system does utilize a fixed 120 second anti-recycle
timer to prevent short cycling of systems and to allow
positioning the Feed and Drain Valves to a zero (closed)
position by the Flash Tank Drain and Feed Valve Controller in the event of a power failure.
On power-up of the control panel, the anti-recycle timer for each system will be set to 120 seconds and must
time out before a compressor is allowed to start.
Whenever a system starts, the anti-recycle timer for all
systems will be set to 120 seconds and will count down
from the time the motor starts. The timer must time out
before another compressor is allowed to start.
Whenever a system shuts down, the anti-recycle timer
for that system will be set to 120 seconds. The timer
must time out before the system is allowed to restart.
Evaporator Pump Control
The evaporator pump dry contacts are energized when
any of the following conditions are true:
If a Low Leaving Chilled Liquid Fault occurs.
Whenever a compressor is running.
The Daily Schedule is ON and the UNIT switch is
ON.
Even if one of above is true, the pump will not run if
the panel has been powered up for less than 30 seconds
or if the pump has run in the last 30 seconds to prevent
pump motor overheating.
Evaporator Heater Control
The evaporator heater is controlled by ambient air
temperature. If no systems are running and the
ambient temperature drops below 40F, the heater is
turned on. If no systems are running and the temperature rises above 45F the heater is turned off. Whenever a system is running, the evaporator heater is turned
off. Both evaporator heater outputs will always be

JOHNSON CONTROLS

turned on and off together. An under voltage condition


will keep the heater off until full voltage is restored to
the system. The heater will protect the evaporator from
freeze-up down to 20F (-29C).
Pumpdown Control
The VSD assures a smooth slow compressor start. As
a result of this, neither pumpdown on start-up or pumpdown on shutdown is required. The Drain and Feed
Valves will close when a compressor stops. This is a
similar to a liquid line solenoid valve closing on a conventional chiller.
Compressor Heater Control
Each compressor has its own heater. The purpose of the
heater is to assure refrigerant does not condense in the
compressor. There is no oil sump, but refrigerant could
possibly condense in the rotors or the motor housing.
The heater will be off whenever the respective compressor is running. As soon as the compressor shuts
off, the heater will turn on as long as all motor temperature sensors in the compressor read less than158F.
The heater will turn off, if any internal compressor motor temperature sensor reads more than160F.
Alarms
Each system has its own alarm. The Alarm output is
ON (dry contact closed) when no fault condition is
present and OFF (dry contact open) to indicate an alarm
situation. The Alarm should be activated (contact
open), if any of the following are true.
A System is faulted or inhibited from starting for
more than 5 seconds.
The Unit is faulted or inhibited from starting for
more than 5 seconds.
A System is locked out.
The Unit is locked out.
Power is removed from the chiller.
Chiller Run Contact
The Chiller Run dry contact is closed whenever any
system is running. It is open when all systems are shut
off.

211

OPERATION

FORM 201.23-NM1 (910)

It is suggested that the System Switches on the keypad be used whenever


possible to turn a system off and allow
the compressor to complete a controlled shutdown.

Unit Switch

Basic operating sequence


Start Sequence and Loading

UNIT
Switch

LD10605

A double pole single throw ON/OFF rocker switch on


the front of the control panel is used to turn the entire
chiller on and off. When the switch is placed in the
OFF position, the entire unit shuts down immediately.
One pole of the UNIT switch contacts is wired to the
Sys 1/3 and the other to Sys 2/4 VSD Run Signal input
and the Chiller Control Board UNIT switch X digital input (X equals System 1 or 2). Separate System
Fuses are also wired in series with each set of UNIT
switch contacts. If either fuse is pulled or blown, only
the system with the good fuse (Input is high) will run.
When both inputs are high, the entire chiller will be enabled to run. When both inputs are low, the chiller will
be disabled as a UNIT switch OFF Shutdown.

The UNIT switch should never be


used to shut down the chiller except
in an emergency. When the switch is
thrown, the compressors will immediately shut down. Since the compressors are not permitted to come to a
controlled stop, the rotors may backspin, which may result in some unusual compressor noise. The backspin will not hurt the compressors, but
should be avoided.

212

To initiate the start sequence of the chiller, the following conditions must be satisfied before the precharge of
the DC Bus will take place:
UNIT SWITCH must be ON.
At least one System Switch is ON
Run permissive inputs (Remote Cycling Contacts)
must be closed.
No unit faults exist.
No unit start inhibits exist.
At least one system not faulted or inhibited.
The Daily Schedule is calling for the chiller to
run.
The Flow Switch is closed.
Leaving Chilled Liquid Setpoint is above the
Setpoint plus CR (Setpoint High Limit).
Once the precharge takes place, if the anti-recycle timer is timed out the chiller control system on the Chiller
Control Board will select the number of compressors
to start and begin operation of the compressors. The
compressor(s) speed will be ramped to the minimum
start frequency and increase speed as needed in an effort to regulate the leaving chilled liquid temperature to
meet the desired Setpoint.
When a compressor starts, the Feed and Drain
Valves on the system will immediately begin to control superheat and the liquid level in the flash tank
and the Chiller Control Board microprocessor will
begin to regulate the speed on the VSD to bring
the chilled liquid temperature to within the Control Range (CR). The microprocessor will regulate
the speed of the compressor(s) primarily based on
temperature offset as the loading timer permits.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

48F

--------------------------------------------------

46F

--------- Setpoint + CR ( Setpoint High Limit) ----------

44F

----------Setpoint ---------------------------------

42F

----------Setpoint CR (Setpoint Low Limit) ----------

40F

--------------------------------------------------

38F

--------------------------------------------------

Programmed
Control (Cooling) Range

FIG. 48 - chiller control (cooling) range

The Setpoint is the Leaving Chilled Liquid Temperature midpoint of the Control (Cooling) Range. The
Setpoint High Limit is the Setpoint plus the Control
Range. The Setpoint Low Limit is the Setpoint minus
the Control Range. The chiller will attempt to control within the temperature range programmed by the
Setpoint plus or minus CR.
Starting and stopping of compressors will be handled
by the Standard or High IPLV Capacity Control Routine. Loading and unloading will be controlled by
temperature offset and rate by the Fuzzy Logic Control
Routine.
A graphical representation of the Setpoint and high and
low limit (plus or minus CR) are shown in FIG. 48.
Number of compressors to start
General
The number of compressors to start control logic varies
between the standard and optional High IPLV chillers.
Standard IPLV chiller control utilizes sequential logic
that requires the microprocessor to start 1 compressor at
a time and only add a compressor when all running compressors reach maximum speed. Optional High IPLV
chillers have control algorithms that provide smart
anticipatory control to determine how many
compressors need to be started to satisfy the current
load. The smart logic is capable of reducing short
cycling, and reducing loading time on a hot water start,
and starting all compressors at the same time.
Standard IPLV
The Standard IPLV control always starts a single
compressor under all circumstances as the first step of

JOHNSON CONTROLS

LD10625

loading. The Chiller Control Board does not make decisions on the number of compressors to start based on
chilled liquid temperatures and prior compressor operation when starting the chiller. An additional compressor is only started when the lead compressor has
reached maximum speed and cooling requirements are
not satisfied.
Optional Optimized High IPLV
On optimized IPLV chillers, the Number of
Compressors to Start Logic will be used to determine
how many compressors should be run when the unit
starts from the all compressors stopped state. This routine will try to run all the compressors unless it is determined that less will be needed due to light load.
The first step in the sequence is for the microprocessor to set the number of compressors to start
equal to the number of compressors in the chiller. The microprocessor will look at two prior conditions relating to the compressor operating time
the previous time it ran and how long the last
compressor has been off along with two indicators of
chilled liquid load requirements (rate of change of chilled
liquid temperature and deviation from setpoint). Temperature deviation is the amount of error compared to
the setpoint high limit (Setpoint plus CR). Based on this
information, the microprocessor will then determine the
number of compressors to start. The flowchart in FIG. 49
describes the compressor starting decision process.
It is desirable to run as many compressors as possible
for increased efficiency. Optimized logic will keep as
many compressors on line and reduce speed in an effort to optimize the use of the entire evaporator tube
surface.

213

OPERATION

FORM 201.23-NM1 (910)

NUMBER OF COMPS
TO START LOGIC

NUMBER OF COMPS TO
START
REDUCTION TABLE
4 COMPS -> 3 COMPS
3 COMPS -> 2 COMPS
2 COMPS -> 1 COMP
1 COMP -> 1 COMP

SET NUM COMPS


TO START = NUM
COMPS IN UNIT

NO

NO

LAST RUN TIME


< 5 MIN ?

OFF TIME
< 5 MIN ?

LCHLT RATE
< 3 F/MIN AND
LCHLT < CR+5F?

YES

YES

YES

REDUCE NUM COMPS


TO START PER
REDUCTION TABLE

REDUCE NUM COMPS


TO START PER
REDUCTION TABLE

REDUCE NUM COMPS


TO START PER
REDUCTION TABLE

NO

CONTINUE

LD10626

FIG. 49 - number of compressors to start

Minimum vsd compressor start/run


frequency

The Minimum VSD Compressor Start Frequency is


based on ambient temperature and determines the
frequency (speed) the compressor(s) is ramped to at
start. At higher ambients, higher speeds are needed
to provide adequate motor cooling. At low ambients,
higher motor speeds are needed to develop oil pressure
differential at start. The temperature ranges and the associated start frequency follows the guidelines below:
If the ambient temperature is 25F or less, the
Minimum VSD Start Frequency will be
70 Hz.
If the ambient temperature is between 26 and 40 F
(-3 and 4C), the Minimum VSD Start Frequency
is 60 HZ.
If the ambient temperature is between 41 and 110 F
(5 and 43C), the Minimum VSD Start Frequency
will be 50 Hz.
If the ambient is between 110 and 125 F (43 and
52C), the Minimum VSD Start Frequency is scaled
according to the following formula:
(3 x Ambient Temperature) - 280F.
The formula is also represented by the graph in FIG.
50.

214

Minimum VSD Frequency (Hz)

Minimum VSD Start Frequency

100
95
90
85
80
75
70
65
60
55
50
45
40
105

110

115

120

125

130

Ambient Temperature (F)

NOTE: The graph above also illustrates the scaled frequency:


LD10627

FIG. 50 - minimum vsd start frequency

A b o v e 1 2 5 F, t h e m i n i m u m V S D S t a r t
Frequency is 95 Hz.
Minimum VSD Run Frequency
The Minimum VSD Compressor Run Frequency is
based on ambient temperature and determines the minimum frequency (speed) the compressor(s) is permitted to run as the system unloads. At high ambients,
higher motor speeds are needed to cool the compressor
motor. The temperature ranges and the associated start
frequency follows the guidelines below:
If the ambient temperature is less than110F, the
Minimum VSD Run Frequency will be 50 Hz.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

If the ambient is between 110 and 125F (43 and


52C), the Minimum VSD Run Frequency is scaled
according to the following formula:
(3 x Ambient Temperature) - 280F.

When a compressor stops, back-spin of the compressor will often occur as the pressure differential between
discharge and suction equalizes. This should not be a
cause of concern.

The formula is also represented by the graph in FIG.


51.

Standard iplv capacity control


(Loading/Unloading and starting additional compressors)

Minimum VSD Frequency (Hz)

100
95
90
85
80
75
70
65
60
55
50
45
40
105

110

115

120

125

130

Standard IPLV Capacity Control is installed in the


chiller at the factory using a dedicated EPROM
(software), part # 031-02476-001, for Standard Only
IPLV control. If the LCHLT is more than the programmed Setpoint plus CR, only a single compressor
is permitted to start under Standard IPLV control. The
compressor will start at the minimum start frequency
based on ambient temperature (Page 214). The lead
compressor Feed and Drain Valves will immediately
begin to control superheat and liquid level in the flash
tank.

Ambient Temperature (F)

NOTE: The graph above also illustrates the scaled frequency:


LD10628

FIG. 51 - minimum vsd RUN frequency

If the ambient temperature is more than125F, the


Minimum VSD Run Frequency will be 95 Hz.
acceleration/deceleration RATE
when starting/stopping compressors
VSD Acceleration and Deceleration Rates
The acceleration rate changes with frequency and follows the guidelines below:
Between 0 and 50 Hz, the acceleration is 10 Hz/
sec.
Between 50 and 200 Hz, the acceleration is 30.4 Hz/
sec. Even though the acceleration rate of 30.4 Hz/
sec is possible up to 200 Hz, the frequency (speed) is
limited by the minimum start frequency and the add
a compressor frequency calculation performed by
the microprocessor when bringing on an additional
compressor.
When decelerating, the deceleration rate changes with
frequency and follows the guidelines below:
Between 200 and 100 Hz, the deceleration time is
30.4 Hz/sec.
Between 100 and 0 Hz, the deceleration time is 10
Hz/sec.
JOHNSON CONTROLS

When a compressor starts, the load and unload timers


will be set to 30 seconds. During the first 30 seconds
of operation after a compressor reaches the start frequency, loading/unloading is inhibited.
After 30 seconds, the control logic looks at the LCHLT
temp, compares it to the Setpoint plus CR, and makes
decisions to load or unload.
For precise capacity control, the Chiller Control Board
microprocessor loads and unloads compressors quickly, as fast as every 2 seconds, in increments of 0.1 to
1 Hz each time a load or unload change is required.
Fixed load and unload timers of 2 sec. are set, after a
speed change of 0.11 to 1 Hz, to minimize undershoot
and overshoot.
As additional cooling is required (LCHLT more than
Setpoint plus CR), the Chiller Control Board microprocessor will increase the speed of the compressor at
the rate of 0.1 to 1 Hz every 2 seconds until the load
is satisfied. Loading will continue to occur as long as
leaving chilled liquid temperature is above the Setpoint
plus CR.
If the temperature falls very near or within the Control
Range, the Chiller Control Board microprocessor will
make decisions regarding speed changes under conditions where the error and rate conflict. Under
these conditions, loading/unloading follows the guidelines described in the Fuzzy Logic Control section
(Page 216).
215

OPERATION
If the compressor speed exceeds the maximum
frequency the compressor is allowed to operate minus
1 hertz for a period of 3 minutes without bringing the
leaving chilled liquid temperature to within Setpoint
plus CR/2, the chiller control will make a decision to
start another compressor. At this point, the first compressor will decelerate to a frequency of 5 Hz. Reducing the frequency of the running compressor to 5 Hz
enables the differential between discharge and suction
pressure to be reduced to a point where it will not affect
motor current when the running compressor is ramped
up. It also reduces the possibility of backspin on the
running compressor. The next lag compressor will be
activated and all compressors will be accelerated to the
START FREQ. The START FREQ is specified by the
formula:
START FREQ = Current VSD Freq x (Number of Compressor enabled -1)
Number of Compressors enabled

For example: Current VSD Freq = max freq of the chiller = 200 Hz.

Number of compressors enabled = 2 = Original

compressor running, plus the compressor to be added.

In this example, assume a single compressor had


been running at the max frequency of 200 Hz without
satisfying cooling demand. (2) compressors are now
enabled when the second compressor is activated. Placing these values in the formula, the START Frequency
equals 200 Hz x (2-1)/2 equals 100 Hz. The compressors will be accelerated to a start frequency of 100 Hz.
Load and unload timers will be set to 30 seconds. The
anti-recycle timer will bew set to 120 seconds.
If additional cooling is required, after the initial 30 seconds of operation, loading will occur at the rate of 0.1
-1 Hz every 2 seconds, unless load limiting occurs.
If the cooling capacity exceeds the demand and temperature continues to drop while in the Control Range
(CR) with multiple compressors operating, the Chiller
Control Board microprocessor will decrease the speed
of the compressor(s) at the rate of 0.1 to 1 Hz every 2
seconds until the LCHLT stabilizes within the Control
Range. If frequency (speed) drops below the LESS
COMP FREQ 20 Hz or the minimum VSD frequency, whichever is higher, the compressors will be decelerated to a speed of 5 Hz, the last compressor disabled,
and the remaining compressor(s) restarted minus one
lag compressor. The LESS COMP FREQ is designated
as:
LESS COMP FREQ = Max VSD Freq x (Number of compressor enabled -1)

Number of Compressors enabled
For example: 200 Hz = max freq of the chiller.

216

FORM 201.23-NM1 (910)

In this example, one compressor will be shut down


when the speed of the compressors drops to 200 Hz x
(2-1)/2 = 100 Hz-20 Hz = 80 Hz.
The restart frequency for the compressor(s) after removing a lag compressor is the OFF FREQ. The OFF
FREQ is designated as:
OFF FREQ = Current VSD Freq x (Number of compressors enabled +1)

Number of Compressors enabled
For example: 80 Hz = current freq of the chiller in the example above.

Number of compressors enabled at shutdown = 1

In the example above, one compressor will restart at


160 Hz as calculated in the formula below:

80 Hz x (1+1) = 160 Hz

1
The load timer will also be set to 30 seconds and the
unload timer will be set to 10 seconds.
On 3 and 4 compressor chillers, if frequency (speed)
drops below the LESS COMP FREQ 20 Hz or
the minimum VSD frequency, whichever is higher,
another lag compressor will be shut down using the
same guidelines.
When the system is only operating a single (lead) compressor, if temperature continues to stay below the Control Range (Setpoint CR) or continues to drop while
in the Control Range, the Chiller Control Board microprocessor will unload the compressor at the rate of 0.1
to 1 Hz every 2 seconds. This will continue until the
frequency drops below the Minimum VSD Frequency
determined by the ambient temperature. At this point,
the lead compressor will be shut down, if temperature
is below the Setpoint - CR.
Fuzzy Logic Control
The fuzzy logic control in software makes decisions to
increase or decrease speed according to the error or deviation from Setpoint, and the rate of change of chilled
liquid temperature. Before making a change in speed,
the Chiller Control Board microprocessor will look at
the load and unload timers to assure they are timed out.
It also looks to assure there is no load limiting in effect.
Each time a change is made, the incremental change in
speed is still between 0.1 and1 Hz, unless temperatures
fall near the leaving chilled liquid cutout.
In most situations, when the chilled liquid temperature is above the Setpoint plus CR, the Chiller Control Board microprocessor will continue to increase

Number of compressors enabled before shutdown = 2


JOHNSON CONTROLS

FORM 201.23-NM1 (910)

the speed of the compressor(s) to load the chiller until


temperature drops in the general range of the Setpoint
High Limit (Setpoint plus CR). If the rate of change is
dropping too fast and there is potential for overshoot,
the Chiller Control Board microprocessor may elect
not to continue to increase speed.
In cases where temperature is dropping too fast when
temperature is within the desired Control Range, the
microprocessor will be required to make decisions regarding speed changes under conditions where the error and rate conflict. For example, the microprocessor may elect to decrease the speed of the compressor(s)
if the error is 0 (temperature is at Setpoint), while the
rate of change of chilled liquid temperature is falling
(negative). The Chiller Control Board microprocessor
may also elect to hold the speed when error is positive (temperature is above Setpoint, but not above
Setpoint plus CR) because the rate of change of chilled
liquid is negative (falling). TABLE 4 illustrates
these conditions.
TABLE 4 - fuzzy logic loading/unloading
vs. error
NEGATIVE
ERROR

ZERO
ERROR

POSITIVE
ERROR

NEGATIVE
RATE

UNLOAD

UNLOAD

HOLD

ZERO
RATE

UNLOAD

HOLD

HOLD

POSITIVE
RATE

HOLD

LOAD

LOAD

To avoid overshoot or nuisance trips on the low chilled


liquid cutout, when the temperature is below the
Setpoint CR/2, the Chiller Control Board microprocessor will reduce the speed of the compressor(s) to
unload the chiller by 2.0 Hz every 2 seconds. If temperature drops to within 1.0F above the Low Chilled
Liquid temp Cutout, the Chiller Control Board microprocessor will unload the compressors at the rate of 4.0
Hz every 2 seconds.
As the temperature rises the microprocessors fuzzy
logic will factor in the rate of change before continuing
to unload. If the rate of change is rising too fast and
there is potential for a positive overshoot, the Chiller
Control Board microprocessor may elect not to continue to decrease speed.

JOHNSON CONTROLS

In cases where temperature is rising too fast, when temperature is within the desired Control Range, the Chiller
Control Board microprocessor will be required to make
decisions regarding speed changes under conditions
where the error and rate conflict. For example, the
Chiller Control Board microprocessor may elect to increase the speed of the compressor(s) if the error is 0
(temperature is at Setpoint), while the rate of change of
chilled liquid temperature is positive (rising). The
Chiller Control Board microprocessor may also elect
to hold capacity when error is negative (temperature
is below Setpoint) because the rate of change of chilled
liquid is positive (rising). TABLE 4 illustrates these
conditions and the loading response from the Chiller
Control Board microprocessor.
Hot Water Starts
On a hot water start under "best" case conditions, assuming power has not been removed and the 120 second timer does not inhibit starting, the design of the
control algorithm for a 2compressor Standard IPLV
leaving chilled liquid capacity control allows full loading of a chiller in slightly more than 14-1/2 minutes,
regardless of the number of compressors. This time
period assumes load limiting does not affect the loading sequence and the ambient is above 40F.
Lag Compressor Operation in Load Limiting
When a single compressor is operating in current,
discharge pressure, suction pressure, VSD internal
ambient, or VSD baseplate temperature limiting for
more than 5 minutes and chilled liquid temperature is
more than Setpoint plus CR, the Chiller Control Board
microprocessor will turn on the lag compressor to
bring the chilled liquid temperature within the Control
Range. After 1 hour the Chiller Control Board microprocessor will shut down the lag compressor and attempt to control temperature with only the lead compressor to satisfy the load.
optional high iplv capacity control
(Loading/Unloading and starting additional compressors)
Optional High IPLV Capacity Control is installed in the
chiller at the factory using a dedicated EPROM (software), part # 031-02476-002, for High IPLV control.
Its purpose is to control compressors as effectively as
possible, optimizing control of both the compressors
and condenser fans. If the LWT is more than the programmed Setpoint plus CR, the Chiller Control Board
microprocessor will follow the flow chart (Page 214)
to determine the number of compressors to start based
on the last run time, time off, and the rate of change
217

OPERATION
of chilled liquid temperature. The compressor(s) will
start at the minimum start frequency based on ambient
temperature (Page 214). The respective system Feed
and Drain Valves will immediately begin to control superheat and liquid level in the flash tank.
When compressors start, the load and unload timers
will be set to 30 seconds. During the first 30 seconds of
operation after a compressor reaches the start frequency, loading/unloading is inhibited. After 30 seconds,
the control logic looks at the LWT temp, compares it
to the Setpoint plus CR, and makes a decision to load
or unload.
For precise capacity control, the Chiller Control Board
microprocessor loads and unloads compressors quickly, as fast as every 2 seconds, in increments of 0.1 to
1 Hz each time a load or unload change is required.
Fixed load and unload timers of 2 sec. are set, after a
speed change of 0.1 to 1 Hz, to minimize undershoot
and overshoot.
As additional cooling is required (LCHLT more than
Setpoint plus CR), the Chiller Control Board microprocessor will increase the speed of the compressor at
the rate of 1Hz every 2 seconds until the load is satisfied. Loading will continue to occur as long as leaving
chilled liquid temperature is above the Setpoint plus
CR.
The chiller control board will be make decisions regarding speed changes under conditions where the error and rate conflict. Under these conditions, loading/unloading follows the guidelines described in the
Fuzzy Logic Control section (Page 219).
If chilled liquid temperature is not satisfied and above
Setpoint plus CR, the microprocessor looks to see if
any of the lag compressors are not running. If any lag
compressor(s) is off, the Chiller Control Board microprocessor looks at the VSD output frequency. If
the VSD output frequency is greater than the ADD
COMPRESSOR FREQUENCY plus 15 Hz or equal
to the maximum chiller speed (frequency), the microprocessor starts an additional compressor. The ADD
COMPRESSOR FREQUENCY is calculated as:
ADD
= Minimum Start Freq x (Number of Compressors Running +1)
COMPRESSOR
Number of Compressors Running
FREQUENCY

Example - A single compressor had been running without satisfying cooling demands. Assume the minimum
VSD start frequency based on ambient is 50 Hz for this
218

FORM 201.23-NM1 (910)

example. The number of compressors running in the


formula will equal to 1. Placing the values into the
formula: 50 Hz x (1+1)/1 = 100 Hz. The add compressor frequency will equal 100 Hz. Since the controls
are designed to add a compressor at a frequency 15
Hz above this point, a compressor will be added if the
speed reaches 115 Hz.
When a compressor is to be added, the Chiller Control Board microprocessor decelerates the compressor
VSD frequency to 5 Hertz. This enables the differential
between discharge and suction pressure to be reduced
to a point where it will not affect motor current when
the compressor is restarted. It also reduces the chance
for backspin on the running compressor. The next lag
compressor is activated and all compressors are accelerated to the START FREQUENCY. The START
FREQUENCY is calculated as:
START = Current VSD Freq x (Number of Compressors Running 1)
FREQUENCY
Number of Compressors Running

With 2 compressors now running and a current VSD


frequency of 115 HZ, the start frequency will be
computed as:
115 Hz x (2-1) = 115 = 58 Hz
2
2
When the compressors restart, loading and unloading is
inhibited for 30 seconds after the compressor(s) reaches the start frequency, as is the case on any compressor
start. The anti-recycle timer will be set to 120 sec.
In a situation where a single compressor on a 2 compressor chiller is running and is in load limiting for
any reason, and LCHLT more than Setpoint plus CR
for less than 5 minutes, but more than 30 seconds, the
microprocessor will reset the load/unload timers to 2
seconds every potential load cycle. When LCHLT
more than Setpoint plus CR for more than 5 minutes,
the microprocessor will enable the lag compressor just
as it were not satisfied and determine a second compressor was required to handle the load, since the lead
compressor is load limited.
If the cooling capacity exceeds the demand (LCHLT
less than Setpoint CR/2) and multiple compressors
are operating, the Chiller Control Board microprocessor will decrease the speed of the compressors at the
rate of 0.1 to 1 Hz every 2 seconds until the LCHLT
rises to within the Control Range. If temp remains
below Setpoint CR/2, rate is falling, and speed falls
to the minimum VSD frequency as determined by the
ambient, the VSD will decelerate all compressors to 5
JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Hertz. The last lag compressor will be shut down. The


remaining compressors will be restarted minus the lag
compressor. The lead compressor will restart and accelerate to the STOP COMP FREQ designated as:
STOP
= Minimum VSD Freq x (Number of Compressors Running +1)
COMP FREQ
Number of Compressors Running
In this example: Number of compressors running = 1
Minimum VSD Freq.= 50 Hz

In the example above, one compressor will restart at


100 Hz as indicated in the formula below:
50 Hz x (1+1) = 100 Hz

1
The load timer will also be set to 30 seconds and the
unload timer will be set to 10 seconds.
On 3 and 4 compressor chillers, if temperature stays
below the Setpoint minus the Control Range/2,
another lag compressor will be shut down using the
same guidelines.
When the system is only operating a single (lead) compressor, if temperature continues to stay below the
Control Range (Setpoint minus CR), the Chiller Control Board microprocessor will unload the compressor
at the rate of 1Hz every 2 seconds. This will continue
until the frequency drops below the Minimum VSD
Frequency determined by the ambient temperature. At
this point, the lead compressor will be shut down.
Fuzzy Logic Control
The fuzzy logic control in software makes decisions to load or unload according to the error or
deviation from Setpoint, and the rate of change of
chilled liquid temperature. Before making a change in
speed, the logic will look at the load and unload timers to assure they are timed out. It also looks to assure
there is no load limiting in effect. Each time a change
is made, the incremental change in speed is still 0.1 to
1 Hz, unless temperatures fall near the leaving chilled
liquid cutout.
In most situations, when the chilled liquid temperature is above the Setpoint plus CR, the Chiller Control Board microprocessor will continue to increase
the speed of the compressor(s) to load the chiller
until temperature drops in the general range of the
Setpoint High Limit. As the temperature drops and
approaches the Setpoint High Limit (Setpoint plus
CR), the microprocessors fuzzy logic will begin factoring in the rate of change before continuing to load.
If the rate of change is dropping too fast and there
JOHNSON CONTROLS

is potential for overshoot, the Chiller Control Board


microprocessor may elect not to continue to increase
speed.
In cases where temperature is dropping too fast, when
temperature is within the desired Control Range, the
Chiller Control Board microprocessor will be required
to make decisions regarding speed changes under
conditions where the error and rate conflict. For example, the Chiller Control Board microprocessor may
elect to reduce the speed of the compressor(s) if the error is
0 (temperature is at Setpoint); while the rate of change
of chilled liquid temperature is negative(falling).
The Chiller Control Board microprocessor may
also elect to hold capacity when error is positive
(temperature is above Setpoint, but not above Setpoint
plus CR) because the rate of change of chilled liquid is
negative (falling). TABLE 5 illustrates these
conditions.
TABLE 5 - fuzzy logic loading/unloading
vs. error
NEGATIVE
ERROR

ZERO
ERROR

POSITIVE
ERROR

NEGATIVE
RATE

UNLOAD

UNLOAD

HOLD

ZERO
RATE

UNLOAD

HOLD

HOLD

POSITIVE
RATE

HOLD

LOAD

LOAD

When temperature is significantly below the Setpoint


minus CR/2, the Chiller Control Board microprocessor
will reduce the speed of the compressor(s) to unload
the chiller by 2.0 Hz every 2 seconds. If temperature
drops to within 1.0F above the Low Chilled Liquid
Temperature Cutout, the Chiller Control Board microprocessor will unload at the rate of 4.0 Hz every 2 seconds.
As the temperature rises toward Setpoint minus CR,
the Chiller Control Board microprocessors fuzzy logic
will begin factoring in the rate of change before continuing to unload. If the rate of change is rising too fast
and there is potential for overshoot, the Chiller Control Board microprocessor may elect not to decrease
speed.
In cases where temperature is rising too fast, when temperature is within the desired Control Range, the Chiller
Control Board microprocessor will be required to make
decisions regarding speed changes under conditions
where the error and rate conflict. For example, the
219

OPERATION
Chiller Control Board microprocessor may elect to increase the speed of the compressor(s) if the error is 0
(temperature is at Setpoint), while the rate of change
of chilled liquid temperature is positive (rising). The
Chiller Control Board microprocessor may also elect
to hold capacity when error is negative (temperature
is below Setpoint) because the rate of change of chilled
liquid is positive (rising). TABLE 5 illustrates these
conditions and the response from the Chiller Control
Board microprocessor.
Hot Water Starts
On a hot water start under best case conditions, assuming power has not been removed and the 120 sec
timer does not inhibit starting, the design of the control algorithm for a 2 compressor High IPLV leaving
chilled liquid capacity control allows full loading of a
chiller in slightly more than 6 minutes, regardless of
the number of compressors, if all the compressors start
at the same time. This time period assumes load limiting does not affect the loading sequence and the ambient is above 40F.
Load limiting control
Load Limiting

FORM 201.23-NM1 (910)

Motor Current Load Limiting/Unloading


Motor current load limiting helps prevent the system
from tripping on the motor overload safety. The motor
Current Limit Setpoint is based on %FLA motor current and is programmable under the PROGRAM key
or may be set by a remote device. Motor current load
limiting prevents the system from loading even though
increased loading may be required when the current is
between the Current Limit Setpoint minus 2% and
the Current Limit setpoint. Between the Current
Limit Setpoint and the Current Limit Setpoint plus
5%, the system will unload every 2 seconds according
to the amount current is exceeding the Current Limit
Setpoint. At the Current limit Setpoint, 0 Hz reduction in speed will take place and at the Current
Limit Setpoint plus 5%, a 10 Hz speed reduction will
take place. Between the Current Limit Setpoint and
Current Limit Setpoint plus 5%, unloading will occur according to the TABLE 6.
TABLE 6 - current limit
load limiting/unloading
CURRENT LIMIT SETPOINT
Current Limit Setpoint
-2% to +0%

UNLOADING
0 Hz

Current Limit Setpoint +1%

2 Hz

Current Limit Setpoint +2%

4 Hz

Current Limit Setpoint +3%

6 Hz

The Load Limiting Controls are intended to prevent


a system from reaching a safety trip level. Load
limiting controls prevent loading or unload compressors to prevent tripping on a safety. Limiting controls
operate for Motor Current %FLA, Suction Pressure,
Discharge Pressure, VSD Baseplate Temperature, and
VSD Internal Ambient Temperature.

Discharge Pressure Load Limiting/Unloading

All running systems load limit control values are


checked every 2 seconds. Load limiting prevents a
system from loading (no increase even though cooling
demand requires loading) when the specific operating
parameter is within a specific range of values. If the
value is above the range where loading is inhibited, the
logic will unload the chiller based on the amount (%)
the limit has been exceeded. Load limiting affects all
compressors, even though only one system may be affected.

Discharge pressure load limiting protects the condenser from experiencing dangerously high pressures.
A system is permitted to load normally as long as the
discharge pressure is below the High Discharge Pressure Cutout minus 20 PSIG. Between Cutout minus
20PSIG and Cutout minus 15 PSIG loading is inhibited even though increased loading may be required.
Between Cutout minus 15 PSIG and the Discharge
Pressure Cutout, forced unloading is performed every
2 seconds according to TABLE 7. The discharge pressure unload point is fixed at 255 PSIG.

Current Limit Setpoint +4%

8 Hz

Current Limit Setpoint +5%

10 Hz

If more than one operating parameter is exceeding


the value where unloading is required, the value with
the highest amount of unloading will determine the
unloading. All load limiting controls are active at startup except suction pressure limiting.

220

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE 7 - discharge pressure


load limiting/unloading
DISCHARGE PRESSURE

UN-LOADING

Discharge Pressure Cutout- 20 PSIG


&

0 Hz

Discharge Pressure Cutout- 15 PSIG


Discharge Pressure Cutout- 13.5 PSIG

1 Hz

Discharge Pressure Cutout- 12 PSIG

2 Hz

Discharge Pressure Cutout- 10.5 PSIG

3 Hz

Discharge Pressure Cutout- 9 PSIG

4 Hz

Discharge Pressure Cutout- 7.5 PSIG

5 Hz

Discharge Pressure Cutout- 6 PSIG

6 Hz

Discharge Pressure Cutout- 4.5 PSIG

7 Hz

Discharge Pressure Cutout- 3 PSIG

8 Hz

Discharge Pressure Cutout- 1.5 PSIG

9 Hz

Discharge Pressure Cutout- 0 PSIG

10 Hz

Suction Pressure Load Limiting/Unloading


Suction pressure load limiting helps to protect the
evaporator from freezing. A system is permitted to load
normally as long as the Suction Pressure is above the
Suction Pressure Cutout plus 2 PSIG. Between Cutout
plus 2 PSIG and the Cutout, loading is inhibited, even
though increased loading is required. Between the
Suction pressure Cutout and Suction Pressure Cutout
minus 10 PSIG, forced unloading is performed every 2
seconds according to TABLE 8 below. This situation
would occur if the suction pressure cutout transient
override control is in effect (See Low Suction Pressure Cutout, Page 247). The suction pressure cutout
is programmed under the PROGRAM key. The default
Suction Pressure Cutout is set at 24.0 PSIG.
TABLE 8 - suction pressure
load limiting/unloading

Suction pressure load limiting is active at start-up, to


only prevent loading of the compressors. Suction pressure limit unloading will not occur until the system run
time reaches 5 minutes of operation to allow the system to stabilize.
VSD Internal Ambient Temperature Load
Limiting
VSD Internal Ambient temperature limiting helps prevent the unit from tripping on the high internal cabinet
temperature safety. A system is permitted to load normally as long as the VSD Internal Ambient is below
the VSD Internal Ambient Cutout minus 3F. Between VSD Internal Ambient Cutout minus 3F and
the VSD Internal Ambient Cutout minus 2F, loading
is inhibited, even though increased loading is required.
Between the VSD Internal Ambient Cutout minus 2F
and the VSD Internal Ambient Cutout, forced unloading is performed every 2 seconds according to TABLE
9 below. The VSD Internal Ambient Safety Cutout is
158F.
TABLE 9 - V
 SD internal ambient
load limiting/unloading
VSD INTERNAL AMBIENT
TEMPERATURE

UN-LOADING

Internal Ambient Temp. is between


Cutout- 3F
&
Internal Ambient Cutout- 2F

0 Hz

Internal Ambient Cutout- 1.8F

1 Hz

Internal Ambient Cutout- 1.6F

2 Hz

Internal Ambient Cutout- 1.4F

3 Hz

Internal Ambient Cutout- 1.2F

4 Hz

Internal Ambient Cutout- 0F

5 Hz

Internal Ambient Cutout- 0.8F

6 Hz

Internal Ambient Cutout- 0.6F

7 Hz

SUCTION PRESSURE

UN-LOADING

Internal Ambient Cutout- 0.4F

8 Hz

Suction Pressure is between


Cutout +2 PSIG &
Suction Pressure Cutout

Internal Ambient Cutout- 0.2F

9 Hz

0 Hz

Internal Ambient Cutout

10 Hz

Suction Pressure Cutout- 1 PSIG

1 Hz

Suction Pressure Cutout- 2 PSIG

2 Hz

Suction Pressure Cutout- 3 PSIG

3 Hz

Suction Pressure Cutout- 4 PSIG

4 Hz

Suction Pressure Cutout- 5 PSIG

5 Hz

Suction Pressure Cutout- 6 PSIG

6 Hz

Suction Pressure Cutout- 7 PSIG

7 Hz

Suction Pressure Cutout- 8 PSIG

8 Hz

Suction Pressure Cutout- 9 PSIG

9 Hz

Suction Pressure Cutout- 10 PSIG

10 Hz

JOHNSON CONTROLS

VSD Baseplate Temperature Load Limiting


VSD Baseplate load limiting helps protect the unit
from tripping on the high VSD Baseplate Temp Safety.
A system is permitted to load normally as long as the
VSD Baseplate temperature is below the VSD Baseplate Temperature Cutout minus 8F. Between the
VSD Baseplate Temperature Cutout minus 8F and the
VSD Baseplate Temperature Cutout minus 4F, loading
is inhibited, even though increased loading is required.

221

OPERATION

FORM 201.23-NM1 (910)

Between the VSD Baseplate Temperature Cutout minus 4F and the cutout, forced unloading is performed
every 2 seconds according to TABLE 10.
TABLE 10 - vsd baseplate temperature
load limiting/unloading
VSD BASEPLATE TEMPERATURE

UN-LOADING

Baseplate Temp. is between


Cutout- 8F
&
Cutout- 4F

0 Hz

Baseplate Temp. Cutout- 3.6F

1 Hz

Baseplate Temp. Cutout- 3.2F

2 Hz

Baseplate Temp. Cutout- 2.8F

3 Hz

Baseplate Temp. Cutout- 2.4F

4 Hz

Baseplate Temp. Cutout- 2.0F

5 Hz

Baseplate Temp. Cutout- 1.6F

6 Hz

Baseplate Temp. Cutout- 1.2F

7 Hz

Baseplate Temp. Cutout- 0.8F

8 Hz

Baseplate Temp. Cutout- 0.4F

9 Hz

Baseplate Temp. Cutout

10 Hz

flash tank drain and feed valve controller


Valve Controller and Control Algorithm
Operation
The Flash Tank Feed and Drain Valve PI Controller(s)
plays a dual role of supplying drive signals to control
the opening and closing of both the Flash Tank Feed
and Drain Valves. These valves control the liquid level
in the flash tank and the suction superheat of the compressor. The Flash Tank Feed and Drain Valve Controller receive analog signals from the Chiller Control
Board to position the Feed and Drain Valves.
The Chiller Control Board PI (Proportional plus Integral) control algorithm in the Chiller Control Board
software determines the open % for the Drain and Feed
valves. A D/A converter on the Chiller Control Board
converts the 0-110.0% signal to an output voltage between 0VDC and 10.28VDC and sends it to the Drain
and Feed Controller. This voltage is then converted
to a valve position by the Drain and Feed Valve Controller and a 2 phase (4 wire), signal drives the Feed
Valve open or closed. Power for the Valve Controller
comes from a 30VDC supply from the Chiller Control
Board.

LD10619

FIG. 52 - flash tank drain and feed valve controller


222

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

The Feed Valve is a stepper motor valve that controls


the liquid flow from the condenser to assure the liquid
level in the flash tank is maintained at a proper level.
The Level Sensor is a rod inserted into the reservoir
connected to the side of the flash tank. The sensing rod
has an active range of about 12.
The control algorithm looks at feedback from the Level
Sensor and compares it to the fixed level setpoint in
the control algorithm. This control strategy attempts
to keep the level in the flash tank to approx 35% of the
usable portion of the sensing rod. In reality, this is approximately a 50% level in the flash tank. As the level
in the flash tank fluctuates, the control algorithm varies
the voltage to the Controller, which in turn sends a 2
phase stepped drive signal to open or close the Feed
Valve as needed.
As the flash tank level varies farther from the setpoint,
the gain of the control algorithm increases for faster response. In some cases, the Feed Valve will fully open
or fully close if the levels become too low or too high.
When properly charged, the condenser subcooling will
be approx. 5-7F at design conditions as the Feed Valve
controls refrigerant flow into the flash tank.
The Drain Valve is also a stepper motor valve. Like the
Feed Valve, the controller receives a 0 to 10.28VDC
signal from the Chiller Control Board. The controller then converts the signal to a valve position and a 2
phase signal drives the Drain valve open or closed.
The Drain Valve, Controller, and Chiller Control Board
Algorithm combination functions as an Electronic Expansion Valve (EEV). The controller receives an analog 0 to 10.28VDC signal sent from the Chiller Control
Board, which is based on system suction pressure and
suction temperature. These operating parameters are
used to compute and control suction superheat according to the Setpoint programmed into the panel under
the PROGRAM key. After computing the superheat,
the signal to the controller is adjusted and the controller subsequently positions the Drain Valve to control
the superheat. The gain of the control algorithm is adjusted to aid in correcting for superheat error.
The Chiller Control Board Algorithm assures the level
in the flash tank does not become too high. The level
setpoint for control is 35%. Levels normally run 30 to
40% with the economizer solenoid energized (open).
With the solenoid closed, levels may vary significantly
from the 30 to 40% level. If the level exceeds 85% of
the full level, the system will shut down on a fault.
JOHNSON CONTROLS

The Feed and Drain Valves in a system open and begin


to control as soon as a compressor starts. When the
compressor shuts down, the valves are driven to their
closed position.
MOP Setpoint Control for Hot Water Starts
Maximum Operating Pressure control overrides superheat control of the Drain Valve when the MOP Setpoint
is exceeded on hot water starts. The fixed setpoint is
68F Saturated Suction Temp (SST). When this value
is exceeded, the Drain Valve switches superheat control to suction pressure control equal to 68F SST.
Moderate To High Ambient MOP Setpoint
Control.
In moderate to high ambients, the suction line may be
warmed by the ambient, contributing to inaccurate suction superheat measurement at start-up. To avoid this
situation, the MOP control utilizes suction pressure
control at start-up, which overrides superheat control.
For the first minute of run time, the MOP Setpoint is
set to:
RCHLT - Superheat Setpoint 1.0F

Run Time in Seconds
After the first minute of operation, the MOP Setpoint is
ramped from the current calculated value to 68F over
the next minute. At this point, normal superheat control based on the programmed setpoint resumes.
Low Ambient MOP Setpoint Control
In low ambient start-ups, suction pressure is erratic
and pressure differentials across the compressor may
be low, resulting in low oil differential faults. The Low
Ambient MOP setpoint control assures adequate
differential is developed between discharge and
suction to push oil through the oil cooling system and
the compressor.
For the first 5 minutes of system run time, the MOP
Setpoint is set to the saturated suction temperature equal
to 15PSIG below discharge pressure, which overrides
superheat control. The control algorithm will not allow suction pressure control below the cutout. The low
limit of the suction pressure is the low suction pressure
cutout. After 5 minutes of system run time, the MOP
Setpoint is set at 68F and superheat control based on
the programmed setpoint resumes.
Actual MOP Setpoint
The actual MOP Setpoint used by the controller is
the minimum of three calculations; the fixed MOP
Setpoint, the moderate to high ambient setpoint, and
the low ambient setpoint.
223

OPERATION

FORM 201.23-NM1 (910)

Valve Controller LEDs


The Drain and Feed Valve stepper motor controller is
equipped with a pair of LEDs on the left side of the
module and 10 LEDs in the center of the module (FIG.
53). These LEDs may be useful during troubleshooting.
A pair of LEDs on the left side of the module
(FIG. 54) indicate when the module is powered. The
Power LED should be lit at all times.

FIG. 55 - power, comms and system open/


close led's
LD10631

FIG. 53 - LED LOCATIONS

FIG. 54 - power and comms led's

LD10629

LD10630

A column of 10 LEDs runs from top to bottom on the


right side module (FIG. 55).

224

A pair of LEDs on the top of the module (FIG. 55)


indicates when the module is powered and when the
module is communicating with the Chiller Control
Board. The Power LED should be lit at all times.
The Open and Close LEDs on each system indicate
when the Feed and Drain valves are being driven open
or closed in an effort to control flash tank level and
suction superheat. These valves will light momentarily when the valves are being pulsed. In most cases
other than start-up, they may appear to not light at all.
The valves that are controlled by the outputs associated
with the LEDs are decoded as shown below:
1 Open = System #1 or 3 Feed Valve Open
2 Open = System #1 or 3 Drain Valve Open
3 Open = System #2 or 4 Feed Valve Open
4 Open = System #2 or 4 Drain Valve Open
5 Close = System #1 or 3 Feed Valve Close
6 Close = System #1 or 3 Drain Valve Close
7 Close = System #2 or 4 Feed Valve Close
8 Close = System #2 or 4 Drain Valve Close
On 3 and 4 compressor chillers, a second module will
control systems #3 and #4.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Due to the short duration of the open and close stepper pulses, LED lighting will be difficult to observe.
In rare cases where validation of the controller output
and valve movement needs to be checked, the valves
can be operated in Service Mode. When operated in
Service Mode, visual indication of the LEDs lighting
will be more obvious. Generally, no audible noise is
evident as the valves open and close unless the valve
is being run against its stop. It is possible to obtain an
indication of valve movement by touch, when a valve
is opening or closing.

Manually operating the Feed and


Drain Valves in Service Mode can
drain or overfill the flash tank. This
could cause valve movements and
levels in the flash tank to act out of the
ordinary when a system first starts,
until the Chiller Control Board brings
the flash tank level and superheat
under control. This may also be evident in the flash tank level and open/
close % on the displays. It may also
cause the liquid line or flash tank sight
glasses to empty or the flash tank sight
glass to fill.
Careless use of manual control could
cause liquid damage to the compressor
when it is started.

Economizer control
The Economizer Solenoid controls a vapor feed to the
economizer port on the compressor from the top of the
flash tank. When the valve is open, refrigerant gases
off in the flash tank providing additional subcooling to
the liquid in the tank. The subcooled liquid is then fed
to the evaporator resulting in additional system capacity and efficiency.
In normal operation, the Economizer Solenoid on a
compressor will be turned on whenever the VSD frequency is more than 120 Hz, the flash tank level is less
than 75%, motor current less than 80%FLA, motor
temperature sensors are all less than less than150F,
and the economizer timer is timed out. Whenever the

JOHNSON CONTROLS

Economizer Solenoid is turned on, the compressor load


timer is set to 35 seconds and economizer timers for
every system are set to 30 seconds, unless they are already above 30 seconds.
In low ambient temperatures less than 40F, run time
on the respective compressor is less than 5 minutes, and
the flash tank level is less than75%, the system Economizer Solenoid is turned on. Under these conditions,
the VSD frequency and the motor temp sensor readings are not factors that could overload the compressor.
Energizing the Economizer Solenoid also helps start a
system in low ambients and prevents low suction pressure and low oil differential faults by increasing the
load.
At ambients above 40F, once on, the Economizer Solenoid will remain energized until the VSD frequency
drops below 90 Hz. Below 90 Hz, the solenoid will
be turned off, regardless of the time remaining on the
economizer timers. Under these conditions, the economizer timers will be set to 0 when the solenoids
are de-energized. Below 100 Hz, if the economizer
timer has timed out, the Economizer Solenoids will be
turned off, the unload timer will be set to 30 seconds,
the economizer timer will be set to 30 seconds if less
than 30 sec.
If a motor temperature sensor exceeds 240 F, the
Economizer Solenoid will de-energize to avoid overheating the hot motor. When the economizer solenoid
is de-energized, the compressor unload timer is set to
30 seconds and the economizer solenoid timer is set
to 60 seconds. All other economizer timers for other
systems are set to 30 seconds, if they are already less
than 30 seconds.
The Economizer Solenoid timer prevents the solenoid
from cycling too often.
Whenever a compressor is to be turned off, all system Economizer Solenoids will be de-energized when
the compressor(s) ramp down. The solenoids on the
compressors that will be ramped back up, if any, will
remain off for 30 seconds before the Chiller Control
Board allows the solenoids to re-energize. Once on,
the economizer solenoid(s) must remain on for 30 seconds as determined by the economizer timer for each
system.

225

OPERATION

FAN
12

FAN
10

FORM 201.23-NM1 (910)

FAN
8

FAN
6

FAN
4

FAN
2

FAN LOCATIONS

SYS
#2

11 FAN UNITS - OMIT FAN 12


VSD/
CONTROL 10 FAN UNITS - OMIT FANS 11 & 12
9 FAN UNITS - OMIT FANS 10,11 & 12
PANEL
8 FAN UNITS - OMIT FANS 9,10,11 & 12

SYS
#1
FAN
11

FAN
9

FAN
7

FAN
5

FAN
3

FAN
1
LD10632

FAN BAFFLES

FAN BAFFLES

FAN BAFFLES

FIG. 56 - CONDENSER FAN LOCATIONS

Condenser fan control


Condenser Fan control on each system is based on discharge pressure. There are up to five possible stages of
fan control utilizing 3 outputs per system. Depending
upon the chiller model, there will be 4, 5, or 6 fans per
system. The fan nearest the discharge liquid header
will always be the first fan on a system to start. As
fan stages increment or decrement, a single fan or pair
of fans contained within a pair of fan baffles will be
turned on or off. The diagram above shows the location of the fan baffles. These baffles will not change
location regardless of the number of fans on a chiller.

The fan control algorithm in the Chiller Control Board


software will not skip steps as fan stages are staged up
and down. The delay between turning on or off fan
stages as discharge pressure rises and falls is 5 seconds.
The controller increments or decrements the fan stage
by one stage based on discharge pressure and fan delay
time.
TABLE 11 shows the fan staging and the outputs for
each fan stage on 4, 5, and 6 fan systems. The microprocessor fan outputs and the fan contactors will be the
same regardless of the number of fans. The fan wiring
will change to permit operation of 4, 5, or 6 fans.

table 11 - fan stages and corresponding outputs


4 FANS

5 FANS

6 FANS

OUTPUT

CONTACTORS

Stage 1
(1 Fan ON)
Sys 1 Fan 1
Sys 2 Fan 2

Stage 1
(1 Fan ON)
Sys 1 Fan 1
Sys 2 Fan 2

Stage 2
(2 Fans ON)
Sys 1 Fans 1 & 11
Sys 2 Fans 2 & 12)

Sys 1: 4CR
Sys 2: 7CR

Stage 2
(2 Fans ON)
Sys 1 Fans 3 & 5
Sys 2 Fans 4 & 6

Stage 2
(2 Fans ON)
Sys 1 Fans 3 & 5
Sys 2 Fans 4 & 6

Sys 1: 5CR
Sys 2: 8CR

Stage 3
(3 Fans ON)
Sys 1 Fans 1, 3, & 5
Sys 2 Fans 2, 4 & 6

Stage 3
(3 Fans ON)
Sys 1 Fans 1, 3, & 5
Sys 2 Fans 2, 4, & 6

1 and 2

Sys 1: 4CR & 5CR


Sys 2: 7CR & 8CR

2 and 3

Sys 1: 5CR & 6CR


Sys 2: 8CR & 9CR

Stage 4
(4 Fans ON)
Sys 1 Fans 3, 5, 7, & 9
Sys 2 Fans 4, 6, 8, & 10

Stage 4
(4 Fans ON)
Sys 1 Fans 1, 3, 5, & 11
Sys 2 Fans 2, 4, 6, & 12
-

1, 2, and 3
Stage 6
Stage 5
Stage 4
(6 Fans ON)
(5 Fans ON)
(4 Fans ON)
Sys 1 Fans 1, 3, 5, 7, 9, & 11
Sys 1 Fans 1, 3, 5, & 7 Sys 1 Fans 1, 3, 5, 7, & 9
Sys 2 Fans 2, 4, 6, & 8 Sys 2 Fans 2, 4, 6, 8, & 10 Sys 2 Fans 2, 4, 6, 8, 10, & 12

226

Sys 1: 4CR, 5CR, & 6CR


Sys 2: 7CR, 8CR, & 9CR

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

The number of fans is factory programmable under the


password protected Unit Setup Mode.
Standard IPLV Fan Control
Fan staging ON and OFF points will be determined
by the ambient temperature. The fan stage will be
incremented, unless the 5 second timer between fan
stages is still timing when the discharge pressure rises
above the Fan ON Press. The fan stage is decremented,
unless the 5 second timer between fan stages is still
timing when the discharge pressure falls below the Fan
OFF Press. When a fan stage is incremented, the fan
delay timer is set to 5 seconds, and the Fan ON pressure is ramped 20 PSIG over the original ON point
back to the original value over the next 20 seconds.
When a fan stage is decremented, the fan delay timer is
set to 5 seconds, and the Fan OFF pressure is ramped
20 PSIG below the original Fan OFF point, back to the
original value over the next 20 seconds. The ON and
OFF points will vary as ambient temperature changes.
FIG. 57 below shows the fan ON and OFF points relative to ambient temperature.

Discharge Pressure (PSIG)

Standard IPLV Fan Control


190
180
170
160
150
140
130
120
110
100
90

Fan On Press
Fan Off Press

75

85

95

105

115

125

Ambient Air Temp (F)

FIG. 57 - standard iplv fan control

LD10633

Optimized IPLV Fan Control


Fan staging ON and OFF points will be determined
by the ambient temperature. The fan stage will be
incremented, unless the 5 second timer between fan
stages is still timing when the discharge pressure rises
above the Fan ON Press. The fan stage is decremented,
unless the 5 second timer between fan stages is still

JOHNSON CONTROLS

timing when the discharge pressure falls below the Fan


OFF Press. When a fan stage is incremented, the fan
delay timer is set to 5 seconds, and the Fan ON pressure is ramped 20 PSIG over the original ON, point
back to the original value over the next 20 seconds.
When a fan stage is decremented, the fan delay timer is
set to 5 seconds, and the Fan OFF pressure is ramped
20 PSIG below the original Fan OFF point, back to the
original value over the next 20 seconds. The ON and
OFF points will vary as ambient temperature changes.
FIG. 58 below shows the fan ON and OFF points relative to ambient temperature.
Optimized IPLV Fan Control
Discharge Pressure (PSIG)

Fan on and off control points will vary for standard


and optional optimized IPLV chillers. Unless controls
dictate all fans running due to high VSD ambient temperatures, fans will sequence on when a compressor
runs and discharge pressure rises. During compressor
ramp up or ramp down when compressors are staged,
the current fan stage will be held.

155
150
145
140
135
130
125
120
115
110
105
100
95
90

Fan On Press
Fan Off Press

75

85

95

105

115

125

Ambient Air Temp (F)

FIG. 58 - HIGH iplv fan control

LD10634

High VSD Cabinet Ambient Temperature Fan


Operation
All condenser fans on all systems will run when the
chiller is off and enabled to run, if the VSD internal
ambient temperature is higher than 5F below the VSD
Cabinet Ambient Temperature Cutout of 158F (158F
minus 5F equals 153 F). When the fans turn on in
this situation, the fan outputs will cycle one at a time
with a 100 ms delay between fan starts. When the VSD
internal ambient falls below the Restart Temperature
(158F Cutout minus 10F equals 148 F), the fans will
all be turned off without a delay.
Vsd temperature control, operation
of the coolant pump, and vsd cabinet
cooling fans
The Coolant pump and VSD Cabinet Cooling Fans will
run to cool the VSD whenever any of the following
conditions are met:
VSD Comp IGBT Baseplate Temperature on a 2 or 4
compressor unit is greater than 10F (5.6C) below
the cutout (Cutout 218F [103.3C] minus 10F
[5.6C] equals 208F [97.8C]). When the VSD
internal ambient falls below the restart temperature
(Cutout 218F [103.3C] minus 15F [8.3C] equals
203F [95C]), the fans and pump will turned off
without a time delay.

227

OPERATION
VSD Comp IGBT Baseplate Temperature on a
3 compressor unit is greater than 10F (5.6C)
below the cutout (cutout 232F [111.1C] minus
10F (5.6C) equals 222F [105.6C]). When the
VSD internal ambient falls below the restart temperature (cutout minus 15F [8.3C] equals 217F
[102.8C]), the fans and pump will be turned off
without a time delay.
Pre-charge Enable 1 from the Chiller Logic Board
is ON.
Pre-charge Enable 2 from the Chiller Logic Board
is ON.
VSD Internal Ambient Temp more than 158F
(70.0C) (Cutout) 10F (5.6C) equals 148F
(64.4C). When the Internal Ambient Temp falls
to less than 158F (70.0C) (Cutout) minus 15F
(8.3C) equals 143F (61.7C) the VSD cooling
fans and glycol pump will turn off.
Condenser Fans (as needed) and VSD coolant pump/
fans will run whenever a compressor is running.
Under these conditions, the condenser fans will run
to control discharge pressure and the VSD coolant
pump/fans will run to cool the IGBT baseplate and
internal cabinet. Additional condenser fans will be
brought on, if the IGBT baseplate temperatures or
internal cabinet ambient rises to 5F (2.8C) below
the cutout. Condenser fans will turn off, if the
compressor turns off provided VSD cooling is not
required. The glycol pump and cabinet fan may
continue to run, if VSD cooling is required.
Glycol Pump and Cabinet Cooling Fans will also
run in the Service Mode if the Fan/Pump Run Bit
is Set.
remote temperature reset control
Temperature Reset Control
Temperature Reset Control is used to reset the actual LCHLT (Leaving Chilled Liquid Temperature)
setpoint used in capacity control. There are several
ways to change the LCHLT setpoint. The first is by
re-programming the Local Cooling Setpoint under the
SETPOINTS key. This is the value the unit will control the LCHLT to if neither of the other methods is
active.
Remote Temperature Limit Reset is only possible if the
option is enabled by both the OPTIONS key selection
and in the factory programmable password protected
Unit Setup Mode.
228

FORM 201.23-NM1 (910)

Remote ISN Setpoint Control


The Remote Leaving Chilled Liquid Setpoint Cooling
Setpoint can be set via the ISN comms. The control
panel will only accept a remote setpoint from the ISN
if the control panel is in Remote Control Mode (under
the OPTIONS key). If the control panel is in Local
Control Mode, the ISN setpoint will be ignored and the
Remote Cooling Setpoint is set to the Local Cooling
Setpoint. The minimum and maximum allowable reset
values will be the same as the minimum and maximum
allowable programmable values for the Local Cooling
Setpoint. If these values are exceeded by the ISN, the
minimum or maximum value will be used.
Contact a local YORK ISN Representative for details
on ISN controls and capabilities.
Remote Temperature Reset
The Remote Leaving Chilled Liquid Cooling Setpoint
can be reset via the Remote Temperature Reset analog
input. A zero signal input (0% input) equates to a 0F
offset to the Local Cooling Setpoint. A full scale signal input (100% input) equates to a "positive" offset to
the Local Cooling setpoint equal to the programmable
Maximum Remote Temp Reset. The offset is linear
and may be adjusted anywhere between the 0% and
100% points. The maximum setpoint allowed is the
maximum programmable Local Cooling Setpoint and
will be capped at this value, if the calculated setpoint
with temperature offset exceeds this value.
This input may be used either in Local or Remote Control Mode. This feature will only operate if enabled
under the UNIT SETUP and the OPTIONS key. The
input will be ignored if the Remote Temp Reset is disabled under the OPTIONS key or if there are valid ISN
comms while in Remote Control Mode. Once a change
to the input is registered, a timer is set to the value of
the Remote Inputs Service Time as programmable under the Unit Setup Mode at the factory for the default
value of 15 minutes. The low limit is 5 minutes and the
high limit is 60 minutes. The Remote input will be
ignored until this timer expires. The timer assures that
rapid changes in a remote reset signal dont result in
poor temperature control or excessive compressor cycling. In most instances, this timer will not need to be
changed, since reset more often than 15 minutes will
create problems with chilled liquid temperature control. Factory Service should be contacted if a timer
change is required.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Control Board jumper JP4 must be positioned correctly to receive either a voltage (0 through 10VDC
or 2 through 10VDC) or current (0 through 20mA or
4 through 20mA) signal. Place the jumper in the V
position for a voltage signal or mA for a current signal
(See FIG. 26 and 27). The software must be configured under the OPTIONS key for the specific type of
input signal to be used.
The maximum temperature reset is achieved at either 10VDC or 20mA. Sending the minimum signal
(0VDC, 2VDC, 0mA, or 4mA based on the OPTIONS
key setting) causes the setpoint to revert back to its local programmed value. If the setpoint reset causes the
setpoint to go over the maximum programmable value,
it will be set to the maximum programmable setpoint.
0 through 10VDC Reset Input
A 0VDC signal produces a 0F reset. A 10VDC signal
produces the maximum remote temp reset (programmable under the SETPOINTS key). The setpoint reset is ramped linearly between these limits as the input
varies between 0VDC and 10VDC. In order for this
input to work properly, the Remote Temperature Reset must be programmed for 0 through 10VDC input
(OPTIONS key) and Chiller Control Board jumper JP4
placed in the V position.
2 through 10VDC Reset Input
A 0 - 2VDC signal produces a 0F reset. A 10VDC
signal produces the maximum remote temp reset (programmable under the SETPOINTS key). The setpoint
reset is ramped linearly between these limits as the input varies between 2VDC and 10VDC. In order for
this input to work properly, the Remote Temperature
Reset must be programmed for 2 through 10VDC input
(OPTIONS key) and Chiller Control Board jumper JP4
placed in the V position.
0 through 20mA Reset Input
A 0mA signal produces a 0F reset. A 20mA signal
produces the maximum remote temp reset (programmable under the SETPOINTS key). The setpoint reset is ramped linearly between these limits as the input
varies between 0mA and 20mA. In order for this input
to work properly, the Remote Temperature Reset must
be programmed for 0 through 20mA input (OPTIONS
key) and Chiller Control Board jumper JP4 placed in
the mA position.

JOHNSON CONTROLS

4 through 20mA Reset Input


A 0 - 4mA signal produces a 0F reset. A 20mA signal
produces the maximum remote temp reset (programmable under the SETPOINTS key). The setpoint reset is ramped linearly between these limits as the input
varies between 4mA and 20mA. In order for this input
to work properly, the Remote Temperature Reset must
be programmed for 4 through 20mA input (OPTIONS
key) and Chiller Control Board jumper JP4 placed in
the mA position.
Local Current Limit Control
Local Current Limit Control is used to set the actual
Current Limit Setpoint. This is accomplished by
changing the Local Current Limit Setpoint under the
PROGRAM key. This is the value at which the unit
will begin to current limit and override capacity control
if remote reset is not actively overriding this control. If
any other current limit methods are active, the lowest
value will be used.
Keep in mind that limiting current may interfere with
capacity control, pulling down chilled liquid temperatures on hot water starts, and maintaining chilled liquid
setpoints.
Pulldown Current Limit Setpoint
The Pulldown Current Limit Setpoint can be set under
the PROGRAM key. This current limit setpoint is only
active on start-up for the time defined by the Pulldown
Current Limit Time under the PROGRAM key. After
the run time has exceeded this time, the Pulldown Current Limit Setpoint is ignored.
This control is useful in limiting current pulldown demand during peak usage periods where electric costs
are highest.
Keep in mind that limiting current may interfere with
capacity control, pulling down chilled liquid temperatures on hot water starts, and maintaining chilled liquid
setpoints.
remote current limit reset control
Remote Current Limit Reset is used to reset the actual current limit setpoint used in current limit control.
There are several ways to change the current limit
setpoint. The first is by reprogramming the Local Current Limit Setpoint under the PROGRAM key. This
is the value the unit will control the current limit to if
neither of the other methods is active.
229

OPERATION
Remote Current Limit Reset is only possible if the option is enabled by both the OPTIONS key selection and
in the factory programmable password protected Unit
Setup Mode.
Remote ISN Current Limit Setpoint
The ISN Current Limit Setpoint can be set via the ISN
comms. The control panel will only accept a Current
Limit Setpoint from the ISN if the control panel is in
Remote Control Mode (under the OPTIONS key). If
the control panel is in Local Control Mode, the ISN
setpoint will be ignored. The minimum and maximum
allowable values will be the same as the minimum and
maximum allowable reset values for the Current Limit
Setpoint under the PROGRAM key. If these values
are exceeded, the minimum or maximum value will be
used.
Contact a local Johnson Controls ISN Representative
for details on ISN controls and capabilities.
Remote Current Limit Reset
The Current Limit Setpoint can be set or reset via the
Remote Current Limit analog input. A zero signal input (0% input) equates to the maximum current limit
setpoint as defined under the PROGRAM key Current Limit Setpoint. A full scale signal input (100%
input) equates to the minimum current limit setpoint
as defined under the PROGRAM key Current Limit
Setpoint. The current limit value is linear and may be
adjusted anywhere between the maximum and minimum points of 0 (no offset) and 100% (max. current
limiting).
This input may be used either in Local or Remote Control Mode. This input will be ignored if the Remote
Current Limit is disabled under the OPTIONS key.
Once a change to the input is registered, a timer is set
to the value of the Remote Inputs Service Time as programmable under the Unit Setup Mode at the factory
for the default value of 15 minutes. The low limit is 5
minutes and the high limit is 60 minutes. The Remote
input will be ignored until this timer expires. The timer assures that rapid changes in a remote reset signal
dont result in poor temperature control or excessive
compressor cycling. In most instances, this timer will
not need to be changed, since reset more often than 15
minutes will create problems with chilled liquid temperature control. Factory Service should be contacted
if a timer change is required.

230

FORM 201.23-NM1 (910)

Control board jumper JP5 must be positioned correctly


to receive either a voltage (0 to 10VDC or 2 to 10VDC)
or current (0 to 20mA or 4 to 20mA) signal. Place the
jumper in the V position for a voltage signal or mA
for a current signal (See FIG. 26 and 27). The software
must be configured under the OPTIONS key for the
type of input signal to be used.
The minimum current limit setpoint is achieved at either 10VDC or 20mA. Sending the minimum signal
(0VDC, 2VDC, 0mA, or 4mA based on the OPTIONS
key setting) causes the current limit to revert back to its
maximum value.
0 through Reset Input
A 0VDC signal sets the current limit to the maximum
value. A 10VDC signal sets the current limit to the
minimum value. The current limit is ramped linearly
between these limits as the input varies between 0VDC
and 10VDC. In order for this input to work properly,
the Remote Current Limit must be programmed for
0 through 10VDC input (OPTIONS key) and Chiller
Control Board jumper JP5 placed in the V position.
2 through 10VDC Reset Input
A 0 - 2VDC signal sets the current limit to the maximum
value. A 10VDC signal sets the current limit to the
minimum value. The current limit is ramped linearly
between these limits as the input varies between 2VDC
and 10VDC. In order for this input to work properly,
the Remote Current Limit must be programmed for
2 through 10VDC input (OPTIONS key) and Chiller
Control Board jumper JP5 placed in the V position.
0 through 20mA Reset Input
A 0mA signal sets the current limit to the maximum
value. A 20mA signal sets the current limit to the
minimum value. The current limit is ramped linearly
between these limits as the input varies between 0mA
and 20mA. In order for this input to work properly,
the Remote Current Limit must be programmed for 0
through 20mA input (OPTIONS key) and Chiller Control Board jumper JP5 placed in the mA position.
4 through 20mA Reset Input
A 4mA signal sets the current limit to the maximum
value. A 20mA signal sets the current limit to the
minimum value. The current limit is ramped linearly
between these limits as the input varies between 4mA
and 20mA. In order for this input to work properly,
the Remote Current Limit must be programmed for 4
through 20mA input (OPTIONS key) and Chiller Control Board jumper JP5 placed in the mA position.
JOHNSON CONTROLS

FORM 201.23-NM1 (910)

sound limit control


(Local and Remote Reset Control)
Sound Limiting and Local Sound Limit
Setpoint
Sound limit control to reduce overall chiller noise levels at specified times of the day is accomplished by setting a Sound Limit Setpoint. There are several ways to
set the Sound Limit Setpoint. The first is by changing
the Local Sound Limit Setpoint under the PROGRAM
key. This is the value the unit will use for sound limiting, if neither of the other methods is active. If any
other sound limit methods are active, the lowest value
will be used. A sound limit of 0% will allow the unit
to run up to the units maximum frequency. A sound
limit of 100% will not allow the unit to run above the
minimum frequency. All other sound limit values are
linear between these 2 points.
A sound limit schedule must be programmed under the
SCHEDULE key when sound limiting is utilized. The
schedule defines the time period that sound limiting
will be active.
Sound Limiting is only possible if the option is enabled
by both the OPTIONS key selection and the factory
programmable password protected Unit Setup Mode.

If Sound Limiting is disabled under


the Unit Setup Mode, nothing relating
to Sound Limiting will show up on any
display screen or printout.
ISN Sound Limit Setpoint
The ISN Sound Limit Setpoint can be set via the ISN
II comms. The control panel will only accept a Sound
Limit Setpoint from the ISN if the control panel is in
Remote Control Mode. If the control panel is in Local
Control Mode, the ISN setpoint will be ignored. The
minimum and maximum allowable values will be the
same as the minimum and maximum allowable values
for the Sound Limit Setpoint under the PROGRAM
key. If these values are exceeded, the minimum or
maximum value will be used.
Contact a local Johnson Controls ISN Representative
for details on ISN controls and capabilities.

JOHNSON CONTROLS

Remote Sound Limit


The Sound Limit Setpoint can be set via the Remote
Sound Limit analog input. A zero signal input (0% input) equates to the minimum sound limit setpoint as defined under the PROGRAM key Sound Limit Setpoint.
A full scale signal input (100% input) equates to the
maximum sound limit setpoint as defined under the
PROGRAM key Sound Limit Setpoint. The input is
linear and may be adjusted between 0% (minimum
sound limiting) and 100% (maximum sound limiting)
points.
This input may be used either in Local or Remote Control Mode. The input will be ignored if the Remote
Sound Limit is disabled under the OPTIONS key.
Once a change to the input is registered, a timer is set
to the value of the Remote Inputs Service Time as programmable under the Unit Setup Mode at the factory
for the default value of 15 minutes. The low limit is 5
minutes and the high limit is 60 minutes. The Remote
input will be ignored until this timer expires. The timer assures that rapid changes in a remote reset signal
dont result in poor temperature control and excessive
compressor cycling. In most instances, this timer will
not need to be changed, since reset more often than 15
minutes will create problems with chilled liquid temperature control. Factory Service should be contacted
if a timer change is required.
Control board jumper JP6 must be positioned correctly
to receive either a voltage (0 to10VDC or 2 to 10VDC)
or current (0 to 20mA or 4 to 20mA) signal. Place the
jumper in the V position for a voltage signal or mA
for a current signal (See FIG. 26 and FIG. 27). The
software must be configured under the OPTIONS key
for the type of input signal to be used.
The maximum sound limit is achieved at either 10VDC
or 20mA. Sending the minimum signal (0VDC,
2VDC, 0mA, or 4mA based on the OPTIONS key setting) causes the sound limit to be set to its minimum
(no limiting) value.
0 through 10VDC Reset Input
A 0VDC signal produces a 0% sound limit (no change
to max VSD freq). A 10VDC signal produces a 100%
sound limit (max VSD freq equals min VSD freq). The
sound limit is ramped linearly between these limits as
the input varies between 0VDC and 10VDC. In order for this input to work properly, the Remote Sound
Limit must be programmed for 0 through 10VDC input
(OPTIONS key) and Chiller Control Board jumper JP6
placed in the V position.
231

OPERATION
2 through 10VDC Reset Input
A 0 through 2VDC signal produces a 0% sound limit
(no change to max VSD freq). A 10VDC signal produces a 100% sound limit (max VSD freq equals min
VSD freq). The sound limit reset is ramped linearly
between these limits as the input varies between 2VDC
and 10VDC. In order for this input to work properly,
the Remote Sound Limit must be programmed for 2
through 10VDC input (OPTIONS key) and Chiller
Control Board jumper JP6 placed in the V position.
0 through 20mA Reset Input
A 0mA signal produces a 0% sound limit (no change
to max VSD freq). A 20mA signal produces a 100%
sound limit (max VSD freq equals min VSD freq). The
sound limit reset is ramped linearly between these lim-

232

FORM 201.23-NM1 (910)

its as the input varies between 0mA and 20mA. In order for this input to work properly, the Remote Sound
Limit must be programmed for 0 through 20mA input
(OPTIONS key) and Chiller Control Board jumper JP6
placed in the mA position.
4 through 20mA Reset Input
A 0 through 4mA signal produces a 0% sound limit
(no change to max VSD freq). A 20mA signal produces a100% sound limit (max VSD freq equals min
VSD freq). The sound limit reset is ramped linearly
between these limits as the input varies between 4mA
and 20mA. In order for this input to work properly,
the Remote Sound Limit must be programmed for 4
through 20mA input (OPTIONS key) and Chiller Control Board jumper JP6 placed in the mA position.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SECTION 8 - MICROPANEL
vsd operation and controls
VSD Logic Board
The VSD Logic Board communications with the Chiller
Control Board via comms and controls the VSD functions. It converts the frequency and run commands
from the Chiller Control Board into the necessary voltage and frequency commands to operate the inverter
section. It also controls the converter section of the
drive (AC Line to DC Bus conversion) by controlling
the pre-charge function.
The VSD Logic Board contains a 2nd microprocessor
(motor controller) that generates the PWM signals that
control the IGBT outputs in the inverter section of the
VSD.
An FPGA handles the hardware safeties that can shut
down the VSD much faster than the software safeties.
The VSD Logic Board handles all of the VSD related
safeties, which includes motor current, BUS voltage,
and other safeties.
The VSD Logic Board reports shutdown information
back to the Chiller Control Board via the RS-485 communication link.
2, 3 and 4 compressor chillers all use the same software.
The microprocessor determines whether the chiller is a
2, 3 or 4 compressor chiller by electronically checking for a factory-installed jumper in the system wiring
harness. The microprocessor checks for the jumper located in the J1 plug wiring harness at power-up. If no
jumper or more than one jumper is sensed, the microprocessor will inhibit start-up. Details regarding the
location of the jumper are provided on Page 210 in the
Chiller Configuration Jumpers section.
VSD Start/run Initiation
Following a successful precharge of the DC Bus and
a run command from the Chiller Control Board, the
VSD Logic Board microprocessor will determine the
motor output voltage (% modulation) and the output
frequency required based on the operating frequency
command from the Chiller Control Board. This information will then be sent to the PWM generator located
on the VSD Logic Board.

JOHNSON CONTROLS

On start-up, the output frequency from the VSD to the


motor(s) will be increased from 0 Hz to the operating
frequency commanded by the Chiller Control Board.
The rate of change of the frequency will also be controlled by the VSD Logic Board.
The rate of change of the output frequency at start-up,
during acceleration is 10 Hz/sec between 0 and 50 Hz
and 30.4 Hz/sec above 50 hertz. The maximum rate
of change of the output frequency during deceleration
between 200 and 100 Hz is 30.4 Hz/sec, and 100 and 0
Hz is 10 Hz/sec.
The VSD Logic Board and its PWM generator will receive operating frequency and voltage commands from
the Chiller Control Board based on the load.
When a frequency (speed) change is requested from the
Chiller Control Board, the chiller microprocessor will
send the change to the VSD Logic Board and the VSD
Logic Board will acknowledge it accepted the change.
Loading and unloading will take place at the rate of 0.1
to 1Hz every 2 seconds.
PWM Generator Type and Carrier Frequency
The PWM generator is responsible for providing asymmetrical uniform sampled PWM waveforms to the
compressor motor at a carrier frequency of 3125 Hz by
turning on an off the inverter IGBTs. The waveform
generated is equivalent to a specific V/F ratio at a given
speed based on the voltage and frequency commands
from the Chiller Control Board. The PWM Generator
receives operating frequency and voltage commands
from the VSD Logic Board control processor.
Short Circuit Protection Minimum Output
Pulse Width and Interlock Delay
The PWM generator is programmed to drop all on
pulses in less than 10 microseconds (and all matching
off pulses in the mirrored waveform) to permit time
for the IGBT gate drivers to detect and self extinguish
an inverter short circuit condition.
Modulating Frequency
The modulating frequency range will range from 0 to
200 Hz. The modulating frequency waveform consists of a sinusoidal waveform summed together with
16.66% of the third harmonic component of the sinusoidal waveform. Utilization of this waveform as the
modulating waveform will permit the drive to generate
a fundamental line to line voltage equal to the DC Bus
voltage divided by 1.414.
233

MICROPANEL
FORM 201.23-NM1 (910)

Maximum VSD Frequency


The maximum VSD frequency will vary for each chiller model. The microprocessor board determines the
frequency according to jumpers' factory installed in
the wiring on the J7 plug of the microprocessor board.
The location of these jumpers' is interpreted as a binary
value, which presently allows 7 speed selections plus a
default. The maximum frequency may vary from 178
to 200 Hz. If the J7 plug is not installed, the speed will
default to 178 Hz. Details on the location of the jumpers' and the associated maximum speed are provided
on Page 210 in the Chiller Configuration Jumpers
section.
VSD % Modulation
The voltage and frequency commands issued by the
VSD Logic Board microprocessor are determined
by the frequency command from the Chiller Control
Board. The VSD output is a PWM signal (FIG. 2),
which has effects on the motor comparable to an AC
voltage sinusoidal waveform. To change the speed of
an AC motor, the frequency of the AC voltage must be
changed. Whenever frequency is changed, the voltage
is changed in a linear ratio. Maintaining a relatively
constant V/F ratio as speed changes assures motor losses and overheating do not occur.
The output voltage of the VSD is not a sinusoidal
waveform. Instead, the PWM generator provides an
output that simulates a true AC waveform by repetitively turning on and off the voltage to the motor to
create an average voltage that is equal to a lower AC
voltage at lower frequencies and a higher voltage at
higher frequencies. The PWM generator also changes
the % modulation of the waveform to simulate the frequency change to maintain the V/F ratio with motor
speed changes.

motor terminals at maximum output frequency that is


equal to the input line to line voltage applied to the
drive (provided the DC Bus current remains continuous).
VSD Cooling and Cooling Loop
The VSD generates heat in the IGBT power modules
and the SCR/Diode assemblies, which must be removed. The heat not only heats the modules but also
the Micro/VSD cabinet.
The VSD is cooled by a glycol loop and circulating
pump. The glycol cooling loop feeds a liquid cooled
heatsink called a chillplate that cools the IGBTs and
SCR/Diode modules. The coolant is pumped by a circulator pump through the heatsink where it absorbs
heat in several passes of tubes on the lower rows of
the inside condenser coils where the condenser fans remove the heat picked up from the modules. The coolant is then pumped back to the modules. The glycol
loop also provides cooling for the Micro/VSD cabinet.
The baseplates of the power components are mounted
to the glycol cooled heatsinks in the cooling loop. The
cooling loop also circulates the glycol through a cooling coil in the cabinet. A fan blows air from the cabinet
across the cooling coil to cool the electronics in the
cabinet.

Never run the glycol pump without


coolant! Running the glycol pump
without coolant may damage the pump
seals
Always fill the system with approved
coolant to avoid damage to the pump
seals and other components.

The PMW generator is programmed to essentially operate a linear volts/Hz ratio over the 0 to 200 Hz frequency range. The complex control algorithm modifies the voltage command to boost the voltage of the
V/F ratio at lower speeds to provide additional torque.

Heat transfer characteristics of the


coolant are very critical. Substituting
coolant or adding water will result in
cooling loop performance loss and
chiller shutdown.

The 100% modulation operating point occurs at a fundamental frequency of 189.6 Hz. As the output frequency increases above 189.6 Hz, the drive operates in
an over-modulated mode. For example, at 200 Hz fundamental modulating frequency the PWM waveform is
over-modulated by approximately 18%. This will yield
a fundamental output line to line voltage applied to the

The glycol coolant level in the VSD cooling system


should be maintained between 9 and 15 inches (23 and
38 cm) from the top of the fill tube. This check should
be performed prior to running the pump. The pump
can be test run by placing the chiller in Service Mode.
It is advisable to fill the tube to the required level before starting the glycol pump because it may empty

234

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

when the pump starts. The level should be topped off


as needed while running. Be sure to re-install the cap
before stopping the glycol pump to avoid overflowing
the fill tube when the glycol pump is turned off.
Glycol coolant has a defined operating life. System
coolant should be changed 5 years from date of shipment of the equipment. Mixing other coolants or water
with the special glycol will reduce the life of the coolant, and cause VSD overheating and damage.
VSD GLYCOL
PUMP

The VSD fan/glycol pump will turn off when ALL of


the following conditions are true:
Compressor 1/3 IGBT Baseplate temp is less than
Cutout minus 15F.
Compressor 2/4 IGBT Baseplate temp is less than
Cutout minus 15F.
Pre-charge Enable 1 from the Chiller Logic Board
is OFF.
Pre-charge Enable 2 from the Chiller Logic Board
is OFF.
VSD Internal Ambient Temp less than Cutout minus
15F.
No compressors are running.
Service Mode Fan/Pump is disabled.

In some cases, the condenser fans may


be turned on by the microprocessor,
when no compressors are running, to
keep the power components and Control/VSD Cabinet from overheating.
IGBT Module Baseplate Temperature Sensing

LD10635

The VSD fan and glycol pump will run if any of the
following conditions listed below are true, provided
the VSD has been powered up for less than 30 seconds
and the pump has not run in the last 30 seconds. The
30 second limitations prevent pump motor overheating.
2 and 4 Compressor Baseplate temp is more than
Cutout (218F) minus 10F.
3 Compressor IGBT Baseplate temp is more than
Cutout (232F) minus 10F.
Pre-charge Enable 1 from the Chiller Logic Board
is ON.
Pre-charge Enable 2 from the Chiller Logic Board
is ON.
VSD Internal Ambient Temp more than Cutout
minus 10F.
Any compressor is running.
Service Mode Fan/Pump Run is enabled.

Each IGBT module has an internal 5Kohm thermistor


built in to measure the temperature of the module. Up
to 4 thermistors are connected to the VSD Logic Board
(one per compressor). The highest module temperature
of compressors 1 and 3 are sent to the logic board along
with the highest module temperature of compressors
2 and 4. If the temperature exceeds the software trip
point, the unit will shut down on a safety. See High
Baseplate Temperature Fault (Page 241) for details.

LM 34
SENSOR

LD10615

ORIGINAL - OBSOLETE P/N 031-02477-000

JOHNSON CONTROLS

235

MICROPANEL
FORM 201.23-NM1 (910)

Following successful completion of the pre-charge


interval, the SCRs on the AC to DC semi-converter
(SCR/Diode Modules) will be gated fully on by the
SCR Trigger Board and the DC Bus will be brought up
to its full potential. After pre-charge has been successfully completed, the SCRs will stay fully on until the
Chiller Control Board turns off the Pre-Charge Enable
via comms.

LM 34
SENSOR

LD13123

NEW BOARD - P/N 031-02507-XXX

VSD Internal Ambient Temperature Sensing


A National LM34 temperature sensor located on the
VSD Logic Board is used to measure the internal ambient temperature of the Control Panel/VSD enclosure.
It has an output voltage that is linearly proportional to
the temperature in degrees Fahrenheit. If the temperature exceeds the software trip point, the unit will shut
down on a safety. See High VSD Ambient Temperature Fault (Page 241) for details.
Pre-charge
When cooling is required (LCWT is more than SPHL),
leaving chilled liquid temp is greater than the setpoint
high limit), the chiller Control Board will send a
Pre-Charge Enable (2 enables on a 4 comp unit) via
comms to the VSD Logic Board. The VSDs DC Bus
voltage(s) across the Bus Filter Capacitors will slowly
be increased to the proper level (more than 500VDC)
through firing of the SCR Trigger Board(s) and the associated pre-charge enable control signal(s). The precharge time interval is fixed at 20 seconds. The purpose of the precharge is to limit current when charging
an uncharged capacitor bank. When uncharged, the capacitor bank looks like an electrical short. The bus is
brought up slowly by only turning on the SCRs during
the trailing half of the + and portion of the incoming
AC sine wave. Following is the status message displayed while the precharge is taking place.
S YS X VSD DC BUS PRECHARGE

236

There will be a Unit Pre-charge Enable for 2 and 3


compressor units and separate System Pre-charge Enables for 4 compressor units.
The pre-charge will only take place when all of the following conditions are true, otherwise it is disabled:
Daily Schedule is ON.
UNIT switch is ON.
System Switch(es) are ON.
Run Permissive(s) are Enabled.
Flow Switch indicates flow.
LCHLT more than Setpoint High Limit.
Unit not faulted / locked out.
Run Mode / Unit Restart
In order to initiate a system run, two conditions must
be met. At least 1 of the 2 systems run signals from the
control panel must be present and at least 1 of the 4
possible Compressor RUN bits must be set in the serial
communications link between the VSD Logic Board
and the Chiller Control Board. Following successful
completion of pre-charge and receipt of the system run
signals, the motor output voltage (% modulation) and
output frequency commands will be determined by the
VSD microprocessor located on the VSD Logic Board.
These two parameters will be sent to the PWM generator located on the VSD Logic Board for waveform
processing at a rate of once every 10 msec.
The voltage and frequency commands issued by the
VSD microprocessor are determined by the operating
frequency command received on the communications
link from the Chiller Control Board and by the present operating frequency of the drive. Upon receipt of
a legitimate run command communication, the VSDs
output frequency will be increased from 0 Hz to the
operating frequency command from the communications link.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

DC Bus Voltage Sensing and Scaling

VSD Transmitted Operating Parameters

Full DC Bus voltage and DC Bus voltages are sensed


for up to 2 DC Buses. 2 and 3 compressor chillers
share a common DC Bus, while 4 compressor chillers
utilize 2 DC Buses (1/3 and 2/4). The DC Bus is wired
to the DC Bus Isolation Board, the voltage is divided
down through a resistance voltage divider, and the reduced voltage is fed to the VSD Logic Board for safety
monitoring.

VSD operating parameters will be transmitted to the


Chiller Control Board over the RS-485 communications link between the 2 boards. These values will be
displayed on the control panel display. The data and
display format are outlined in the TABLE 12 below.

Current Sensing and Scaling


Individual current transformers on each leg sense three
phases of output current on each compressor. These
signals are buffered, divided by 2, and filtered by an
RMS to DC converter. The highest of the currents in
the three phases of each compressor leaving the RMS
converters is then sent to an A-D converter scaled,
monitored by the VSD Logic Board overload and high
current protection circuitry, and sent to the Chiller Control Board for display as the compressor current.
In order to set the motor overload level (determined by
the setting of the overload ADJUST potentiometer on the VSD Logic Board), the voltage level on the
wipers of the four overload ADJUST potentiometers is continuously sensed by the VSD Logic Board
for current protection and sent to the Chiller Control
Board for both display purposes and for current limiting control. This parameter is the 105% FLA value.

vsd safeties (faults)


VSD operating conditions are monitored by both software algorithms and hardware circuitry. Both types
exist as a result of the need for both extremely fast
protection requirements such as a short circuit condition or a slow reacting trip such as a slow rising overload condition. To eliminate nuisance unit trips, the
sensor inputs for the VSDs operating parameters are
averaged four times before Software generated unit/
system fault trips from the VSD Logic Board are initiated. These faults cause single compressor or total unit
controlled ramped shutdown. Other parameters that
are not fed to the VSD Logic Board microprocessor are
protected by Hardware generated fault trips. Hardware trips involve electronic circuitry that measures
voltages or currents and activate level sensitive comparators connected to programmable gate arrays on the
VSD Logic Board FPGA (Field Programmable Gate
Array).
These safeties operate extremely fast and
provide immediate shutdown, because they are not
dependent upon software program loops that operate
in seconds or fractions of a second. Outputs from the
gate arrays provide a digital signal to indicate whether
a safety threshold has been reached.

TABLE 12 - VSD operating display parameters


DATA
Highest Phase of Compressor Motor Current in Amperes RMS (per Compressor)

DISPLAY
FORMAT
XXX Amps

VSD Output Frequency

XXX.X Hz

Motor Overload Setting (105% FLA potentiometer setting) in amperes RMS(per Compressor)

XXX Amps

DC Bus Voltage in DC Volts (maximum of 2)

XXX Volts

VSD Internal Ambient Temperature

XXX.XF (or C)

IBGT Power Assembly Power Module Highest Baseplate Temperature (maximum of 2)

XXX.XF (or C)

Pre-Charge Enable Signal (maximum of 2)

On or OFF

VSD cooling Fan/Pump

On or OFF

Compressor Run Status (maximum of 4)

On or OFF

JOHNSON CONTROLS

237

MICROPANEL
FORM 201.23-NM1 (910)

Immediate Fault shutdowns are often accompanied


by audible motor backspin due to equalizing of the
differential between discharge and suction when the
compressor is turned off while rotating at high speeds.
This should not cause concern and will not damage the
chiller.
Each fault outlined in the descriptions that follow will
indicate whether it is a hardware or software generated
fault.
It will be noted the ramped shutdown results in minimal compressor backspin and noise associated with
backspin. Immediate shutdowns will result in compressor backspin and a higher noise level based upon
the differential pressure between discharge and suction.
When a VSD fault occurs, the VSD Logic Board captures VSD data in the onboard battery backed RAM.
At the same time, the VSD Board Fault Relay will
open, signaling the Chiller Control Board microprocessor to save a snapshot of system data. The VSD
Logic Board then transmits the fault data to the Chiller
Control Board microprocessor on the next comms between the two boards. If the Chiller Control Board
receives the comms fault indication before the Fault
Relay signal, it will immediately save a snapshot of
system data when the comms fault is recognized. This
also enables the microprocessor to capture fault data if
the Fault relay fails. Both the system and VSD fault
data are then stored in the Chiller Control Board history buffers. Any additional faults that may occur during
shutdown on the first fault or between the first fault and
the next comms will also be stored and transmitted to
the Chiller Control Board along with the original fault
data. This data will be stored as ALL FAULT data.
When the control panel acknowledges a fault (via the
fault acknowledge bit in comms) the fault relay will be
reset (closed) by the VSD Logic Board and the fault
indication flag (in comms) will be reset.
The fault relay will not open when a non-running fault
occurs. In this case, the system will be inhibited from
running until the fault condition is corrected. An inhibit message will be displayed on the panel display
indicating the system is not allowed to run. Examples
of this type of fault would be the High Internal Ambient fault and the VSD CT Plug Fault. When the chiller

238

receives the transmitted fault data via comms, it will


save a snapshot of system data in the history buffer
even though the chiller is not running.
Some faults will be unit faults; other faults will be system (specific compressor or compressor pairs) faults,
depending upon the number of compressors in the
chiller. Most faults will shut down the unit/ system
and allow restart once the fault clears and the 120 sec
anti-recycle timer times out. These faults will allow
up to 3 faults in 90 minutes before locking out the unit/
system. Other faults lock out the unit/system after only
a single fault. Details on individual faults are provided
in the following explanations.
A start inhibit will take place if a VSD fault condition
exists and a compressor that is not running is called to
start. The start inhibit will be cleared when the fault
condition goes away and the compressor will be permitted to start.
Pre-charge Low DC Bus Voltage (Software) Fault
The DC Bus voltage must reach at least 50VDC within
four seconds and 500VDC within 19 seconds after the
pre-charge signal has been asserted. If not, the unit/system will shut down on a fault.
This is an auto-restart safety that will lock out on the
3rd fault in 90 minutes. The fault will be a unit fault
for 2 or 3 compressor chillers. The Status display fault
message is shown below:
UNIT YYYYYYYY
PRECHARGE - LOW DC BUS VOLTAGE

The Low DC Bus voltage fault will be a unit fault for 2


and 3 compressor units or a system fault for System 1/3
or 2/4 for 4 compressor units. The reason for this is two
inverter power sections with separate DC Bus circuitry
for each inverter section is utilized on a 4 compressor
unit. One section serves systems 1 and 3 while another
serves systems 2 and 4. The Status display fault message is shown below:
SYS X YYYYYYYY PRECHARGE - LOW DC BUS VOLT

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Pre-charge DC Bus Voltage Imbalance (Software) Fault


The 1/2 DC Bus voltage magnitude must remain within plus or minus 100VDC of the total DC Bus voltage
divided by two during the pre-charge interval. If not,
the unit/system shall shut down on a fault.
This safety will lock out on the 1st fault. The fault will
be a unit fault for 2 or 3 compressor units. The Status
display fault message is shown below:
UNIT YYYYYYYY
PRECHARGE - DC BUS VOLTAGE IMBALANCE

The fault will be a System 1/3 or 2/4 fault for 4 compressor units. Two key presses of the STATUS key are
required to show the fault on both systems. The Status
display fault message is displayed below:
SYS X YYYYYYYY PRECHARGE-BUS VOLT IMBAL

Low DC Bus Voltage (Software) Fault


The low DC Bus voltage trip level is set at 500VDC. If
the DC Bus drops below this level the unit/system will
fault and immediately shut down.
The low DC Bus voltage cutout is an auto-restart safety
that will lock out on the 3rd fault in 90 minutes. The
fault is a unit fault for 2 or 3 compressor units. Below
is an example of the Status display fault message:
UNIT YYYYYYYY
LOW DC BUS VOLTAGE

The low DC Bus voltage cutout is a system fault (1/3


or 2/4) on 4 compressor units. Two key presses of the
STATUS key are required to show the fault on both
systems. Below is a sample Status display system fault
message:
SYS X YYYYYYYY LOW DC BUS VOLTAGE

X indicates the system and YYYYYYY indicates the


system is in a LOCKOUT condition and will not restart until the operator clears the fault using the keypad.

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.

High DC Bus Voltage (Hardware) Fault

DC Bus Voltage Imbalance (Software) Fault

The high DC Bus voltage trip level is determined by


hardware on the VSD Logic Board and is designed to
trip the unit at 766 plus or minus 30VDC. If the DC
Bus exceeds this level, the unit/system will fault and
shut down immediately.

The 1/2 DC Bus voltage magnitude must remain within plus or minus 100VDC of the total DC Bus voltage
divided by two. If the 1/2 DC Bus magnitude exceeds
the plus or minus 100VDC tolerances, the unit/system
will fault and immediately shut down.

This safety is an auto-restart safety that will lock out


on the 3rd fault in 90 minutes. The fault will be a unit
fault for 2 or 3 compressor units. Two key presses of
the STATUS KEY are required to show the fault on
both systems. Below is the control panel Status display
fault message:

This safety will lock out on the 1st fault. The fault will
be a unit fault for 2 or 3 compressor units. Below is the
Status display fault message:

UNIT YYYYYYYY
HIGH DC BUS VOLTAGE

The fault will be a System 1/3 or 2/4 fault on 4 compressor units. Below is the Status display fault messages for all systems. Two key presses of the STATUS
key are required to show the fault on both systems.
SYS X YYYYYYYY HIGH DC BUS VOLTAGE

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.
JOHNSON CONTROLS

UNIT YYYYYYYY
DC BUS VOLTAGE IMBALANCE

The fault will be a System 1/3 or 2/4 fault on 4 compressor units. Two key presses of the STATUS key are
required to show the fault on both systems. Below is a
sample Status display fault message:
SYS X YYYYYYYY DC BUS VOLTAGE IMBALANCE

X indicates the system and YYYYYYY indicates the


system is in a LOCKOUT condition and will not restart until the operator clears the fault using the keypad.

239

MICROPANEL
FORM 201.23-NM1 (910)

High Motor Current (Hardware) Fault

Motor Current Overload (Hardware) Fault

The three output lines to each phase of the compressor motor are monitored via three current transformers
within the VSD. The units three phases of instantaneous output current will be compared to a predetermined limit, which is contained in hardware. The nominal peak current trip level is 575.5 Amps (554A min.,
597A max.). 380VAC, 60Hz and 400VAC, 50Hz nominal peak current trip level is 649.5 Amps (626 Amps
min., 674 Amps max.). The variation in trip point is
the result of component tolerances on the VSD Logic
Board. If the peak current limit is exceeded, the unit
will fault and shutdown immediately.

The Motor Current Overload will compare the highest


of the 3 phases of motor current per compressor to the
compressors overload ADJUST potentiometer setting.
If the current exceeds the setting continuously for 30
seconds, all compressors will fault and shut down immediately.

This fault is an auto-restart safety that will lock out


system on the 3rd fault in 90 minutes. The fault will
be an individual system/compressor fault for all units.
Following is a sample Status display fault message:
SYS X YYYYYYYY HIGH MOTOR CURRENT

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart or
LOCKOUT and will not restart until the operator
clears the fault using the keypad.
Motor Current Overload (Software) Fault
The Motor Current Overload will compare the highest
of the 3 phases of motor current per compressor to the
compressors 105 % FLA ADJUST (overload) potentiometer setting on the VSD Logic Board. If the current
exceeds the setting continuously for 20 seconds, the
compressor will trip.
This safety will lock out a system on the 1st fault and
shut down with a controlled ramped shutdown. The
fault will be an individual system/compressor fault for
all systems. A sample Status display fault is shown
below:
SYS X YYYYYYYY MOTOR CURRENT OVERLOAD

X indicates the system and YYYYYYY indicates the


system is in a LOCKOUT condition and will not restart until the operator clears the fault using the keypad.

240

The fault will be a unit fault and will lock out all systems on the first fault. A sample Status display fault is
shown below:
UNIT YYYYYYYY
MOTOR CURRENT OVERLOAD

YYYYYYYY indicates the unit is in a "Lockout" condition and will not restart until the operator clears the
fault using the keypad.
IGBT Gate Driver (Hardware) Fault
The units phase bank assembly(s) contains one IGBT
gate driver control board per compressor. These boards
monitor the saturation voltage drop across each of the
six IGBTs while gated on. If the IGBTs saturation
voltage exceeds the prescribed limit, the gate driver
will make the determination that a short circuit is present. This in turn will cause the system to trip. During normal operation, the voltage drop across a saturated IGBT is low. When a short or shoot occurs, the
extremely high current causes the voltage across the
device to increase. When the electronic hardware on
the IGBT Gate Driver Board senses the current rise, it
immediately turns off all IGBTs in the module and the
system will shut down immediately.
Additionally, if the IGBTs Gate Driver boards power
supply voltage falls below the permissible limit, this
same fault will be generated.
This is an auto-restart safety that will lock out on the
3rd fault in 90 minutes. The fault will be a system fault
for all units. Following is the Status display fault messages for all systems.
SYS X YYYYYYYY GATE DRIVER

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart or
LOCKOUT and will not restart until the operator
clears the fault using the keypad.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

High Baseplate Temperature (Software) Fault


Each phase bank assembly contains one liquid cooled
heatsink to cool both the inverter power modules and
the converter SCR/Diode modules. Each compressors
inverter power module (6 IGBTs and Gate Driver
Board) contains an internal temperature sensor (5K
ohm at 25 Deg. C) to monitor the baseplate temperature.
On two compressor chillers, the outputs from System 1
and System 2 sensors are each compared in software to
a limit of 218F. If either sensor exceeds this limit, the
unit will fault and shut down with a controlled ramped
shutdown.
On 3 compressor chillers, the baseplate temperatures
on compressors 1 and 3 are ORd together and the
highest of the two temperatures is compared in software to a limit of 232F. Compressor #2 will have its
individual power module sensor compared in software
to a limit of 232F. If the limit is exceeded by either
of the 2 inputs, the unit will fault and shut down with a
controlled ramped shutdown.

3 compressor chillers operate at


higher baseplate temperature compared to 2 or 4 compressor chillers.

On 4 compressor chillers, the baseplate temperatures on


compressors 1 and 3 are ORd together and the highest
of the two temperatures is compared in software to a
limit of 218F. The baseplate temperatures on compressors 2 and 4 are ORd together and the highest of
the two temperatures compared in software to a limit
of 218F. If the limit is exceeded by either of the 2 inputs, the unit will fault and shut down with a controlled
ramped shutdown.
This is an auto-restart safety that will lock out on the
3rd fault in 90 minutes. The fault will be a system fault
for all units. Below are the Status display fault messages for all systems.
SYS X YYYYYYYY HIGH VSD BASEPLATE TEMP

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.

JOHNSON CONTROLS

After a fault, the fan(s) and water pump will remain


energized until the inverter power module base plate
temperature(s) falls below 165F. The system will be
allowed to restart when the inverter power module base
plate temperatures drop below this value.
It is possible for an internal sensor to fail and not sense
temperature without causing a high baseplate sensor
fault.
High VSD Internal Ambient Temperature
(Software) Fault
The VSD Logic board contains a temperature sensor,
which monitors the units internal ambient temperature. If the VSD internal ambient temperature rises
above the cutout of 158F, the unit will fault and shut
down with a controlled ramped shutdown.
This safety will not cause a lockout. The fault will be a
unit fault for all units. Following is the Status display
fault message.
UNIT YYYYYYYY
HIGH VSD INTERNAL AMBIENT TEMP

The unit will be allowed to restart when the internal


ambient temperature drops 10F below the cutout.
YYYYYYYY indicates the unit is in a "Fault" condition and will restart when the condition clears.
Single Phase Input (Hardware) Fault
The VSDs SCR Trigger Control board contains circuitry that checks the three phase mains for the presence of all three-line voltages. If any of the line voltages are not present, the system will immediately shut
down on a fault.
This fault will not cause a lockout. The fault will be
a unit fault for 2 or 3 compressor units. Below is the
Status display fault message.
UNIT YYYYYYYY
SINGLE PHASE INPUT VOLTAGE

The fault will be a system fault 1/3 or 2/4 for 4 compressor units. Two key presses of the STATUS key are
required to show the fault on both systems. Below is
the fault message for all systems.
SYS X YYYYYYYY SINGLE PHASE INPUT VOLTS

X indicates the system and YYYYYYY indicates the


system is FAULT and will restart when the single
phase condition clears.
241

MICROPANEL
FORM 201.23-NM1 (910)

Power Supply (Hardware) Fault

VSD Logic Board Failure (Software) Fault

Various DC power supplies which power the VSD


Logic Board are monitored via hardware located on the
logic board. If any of these power supplies fall outside
their allowable limits, the unit will immediately shut
down on a fault.

Upon receipt of the voltage and frequency commands,


the PWM generator will acknowledge receipt of the
command. If the system microprocessor does not receive the handshake within 1.5 seconds of issuing the
command, the unit will trip. This safety is only active
during precharge and during running of a compressor.
It is not active when all the compressors are shut down
and the precharge is disabled. If the VSD Logic Board
Fault occurs while the chiller is running, all systems
will immediately shut down on a fault.

This is an auto-restart safety that will restart after the


fault clears and lock out on the 3rd fault in 90 minutes.
The fault will be a unit fault for all units. Below is the
Status display fault message.
UNIT YYYYYYYY
VSD LOGIC BOARD POWER SUPPLY

YYYYYYY indicates the system is in a FAULT condition and will restart when the fault clears or LOCKOUT and will not restart until the operator clears the
fault using the keypad.
Run Relay (Software) Fault
Upon receipt of either of the two types of run commands (hardware and software) a 5 second timer will
commence timing. The hardware run signal comes
from the SYS X VSD Run Signal to the VSD Logic
Board. The software run signal comes through the
comms from the Chiller Control Board. If the missing
run signal is not asserted within the 5-second window,
the system will fault. In addition, if either run signal is
disabled while the VSD is running, the remaining run
signal must be disabled within 5 seconds after the VSD
is shut down or the system will fault. If running, the
unit will fault and shut down with a controlled ramped
shutdown.
Control Panel Info - This is an auto-restart safety that
will autostart after the 120 second anti-recycle timer
times out and will lock out on the 3rd fault in 90 minutes. The fault will be a system fault for 2 compressor
units. On 3 and 4 compressor units, the fault is combined as a 1/3 or 2/4 system fault. Below are the fault
messages for all systems.
SYS X YYYYYYYY VSD RUN RELAY

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.

242

This is an auto-restart safety that will auto restart after


the 120 second anti-recycle timer times out and lock
out on the 3rd fault in 90 minutes. The fault is a unit
fault for all units. Following is the fault message.
UNIT YYYYYYYY
VSD LOGIC BOARD FAILURE

VSD CT Plug (Hardware) Fault


Jumpers are installed in each CT plug on the VSD Logic Board to feed back signals to indicate if the plugs are
installed or not. If either plug is not installed, a low
value is read on the digital input and the unit will immediate shutdown on a fault or will not run if off.
This is an auto-restart safety that will restart after the
120 second anti-recycle timer times out and lock out on
the 3rd fault in 90 minutes. The fault is a unit fault for
all units. Following is the fault message.
UNIT YYYYYYYY
VSD CT PLUG FAULT

YYYYYYYY indicates the system is in a FAULT


condition and will restart or "LOCKOUT" and will not
restart until the operator clears the fault using the keypad.
VSD Fault Data
When a fault has occurred, the VSD Logic Board will
capture fault data. This data will be stored in the onboard battery backed RAM for safekeeping and transferred to the panel via the communications link as soon
as possible.
A fault code will be set for the fault that initiated the
system shutdown. This fault will appear as a specific
fault in the Status message.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Any faults that occur after the initial fault, which occur
within the comms transmission time frame following
the inception of the first fault, will be stored and transmitted to the Micro Logic Board together with the first
fault data. These faults will appear in the "All Fault"
display in the History.
A snapshot of the operating parameters of the VSD is
continuously updated in battery-backed memory once
every program loop. Upon receipt of a first fault, the
snapshot of the operating parameters will be stored in
memory and are transmitted to the panel as the fault
data.

unit warnings
Unit Warning Operation
Unit warnings are caused when a condition is present requiring operator intervention to restart the unit.
All setpoints, program values, and options should be
checked before operating the unit. Warnings are not
logged to the history buffer. If a unit warning is in
effect, the message will be displayed to the operator
when the STATUS key is pressed.
STATUS
KEY

Fault Relay/Fault Acknowledge Bit


Control of the Fault Relay is from the VSD Logic
Board. The Fault Relay on the VSD will be closed
during a non-fault condition.

When a running or pre-charge fault occurs on the VSD,


the fault relay will immediately open. The relay will
not open for non-running faults that occur.
When the Chiller Control Board sees the VSD fault relay open, it will immediately take a snapshot of system
data and save it to the history buffer.
A fault acknowledge bit from the Chiller Control
Board is sent to the VSD via comms after receiving
valid fault data from the VSD. When the VSD Logic
Board receives the fault acknowledge via comms from
the panel it will reset (close) the Fault Relay. The fault
acknowledge is reset by the Chiller Control Board after
the Fault Relay is closed by the VSD Logic Board.
VSD Fault Compressor Start Inhibit
If a VSD fault condition exists while the compressor is
not running or pre-charging, the Chiller Control Board
will not try to start the faulted compressor(s). The start
inhibit will be automatically cleared when the fault
condition goes away.

LD10605

Low Battery Warning


The LOW BATTERY WARNING can only occur at
unit power-up. On micropanel power-up, the RTC battery is checked to see if it is still operational. If it is,
normal unit operation is allowed. If the battery voltage
is determined to be low, the following warning message is displayed indefinitely.
UNIT WARNING: !! LOW BATTERY !!
CHECK SETPOINTS/PROGRAM/OPTIONS/TIME

If a low battery condition exists, all programmed


setpoints, program values, time, schedule, and history
buffers will have been lost. These values will all be reset to their default values, which may not be the desired
operating values. Once a bad battery is detected, the
unit will be prevented from running until the MANUAL OVERRIDE key is pressed. Once the MANUAL
OVERRIDE key is pressed, the anti recycle timers will
be set to the programmed default anti recycle time to
allow the operator sufficient time to check setpoints,
program values, etc.
JOHNSON CONTROLS

243

MICROPANEL
FORM 201.23-NM1 (910)

If a low battery is detected, it should be replaced as


soon as possible. The programmed values will all be
lost and the unit will be prevented from running on the
next power interruption. The RTC/Battery is located
on the Chiller Logic Board shown below:

Invalid Serial Number Warning


If the INVALID SERIAL NUMBER message appears,
immediately contact Johnson Controls Product Technical Support. The appearance of this message may mean
the chiller has lost important factory programmed information. The serial number can be entered using the
SERVICE key.
UNIT WARNING: INVALID SERIAL NUMBER
ENTER UNIT SERIAL NUMBER

RTC/
BATTERY

YORk

Additionally, when this appears, an Optimized IPLV


chiller will only run in Standard IPLV control mode.
Optimized IPLV cannot be enabled unless the serial
number is programmed into the unit using the special
password supplied by Johnson Controls Product Technical Support. Once the password is entered, a second password will be needed to activate the optimized
IPLV control (see Page 292).

M ADE IN THE USA

LD10590

Invalid Number of Compressors Warning


The INVALID NUMBER OF COMPRESSORS SELECTED Warning will occur after the VSD has been
initialized, if no Number of Compressors Select
jumpers are installed or if more than 1 jumper is installed. The following warning message will be displayed indefinitely.
UNIT WARNING:
INVALID NUMBER OF COMPRESSSORS SELECTED

This status message can be bypassed to view additional


messages under the STATUS key by pressing the STATUS key repeatedly to scroll through as many as three
STATUS messages that could possibly be displayed at
any time.
Optimized Efficiency Disabled
If the OPTIMIZED EFFICIENCY DISABLED message appears, immediately contact Johnson Controls
Product Technical Support or Johnson Controls ES
Commercial. The appearance of this message means
an optimized chiller is programmed for standard control.
UNIT WARNING: OPTIMIZED EFFICIENCY
DISABLED - CONTACT YORK REPRESENATIVE

To clear this warning, both the control panel and VSD


control voltage must be turned off and the jumpers
properly installed in the VSD wiring harness (see Page
210 for more details on jumper installation).

Optimized IPLV cannot be enabled unless a special


password is entered. Once the password is entered and
the option is enabled using the SERVICE key, the message will disappear (see Page 292).

These jumpers are factory installed in


the wire harness plug and should not
require changes.

This status message can be bypassed to view additional


messages under the STATUS key by pressing the STATUS key repeatedly to scroll through as many as three
STATUS messages that could possibly be displayed at
any time.

244

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

unit safeties
Unit Safety Operation
Unit faults are safeties that cause all running compressors to be shut down, if a safety threshold is exceeded
for 3 seconds. Unit faults are recorded in the history
buffer along with all data on the unit and system operating conditions. Unit faults are auto reset faults where
the unit will be allowed to restart automatically after
the fault condition is no longer present. The only exception is any of the VSD related unit faults. If any 3
VSD unit faults occur within 90 minutes, the unit will
be locked out on the last fault. A VSD lockout condition requires a manual reset using the system switches.
Both system switches must be cycled off and on to
clear a VSD unit lockout fault. If a unit safety is in
effect, the message will be displayed to the operator
when the STATUS key is pressed.
STATUS
KEY

If a VSD fault occurs during the fault rampdown or


while the systems are shut down, the VSD fault will
be registered as a new fault. The reason for this is the
belief any VSD fault should be registered with a full
account of the systems data at the time of the fault.
High Ambient Temp Fault
If the ambient temperature rises above 130 F, the chiller
will shut down with a controlled ramped shutdown. Restart will automatically occur, if demand allows, when
temperature falls 2F below the cutout (128F). This
fault cannot cause a lockout. The fault display message
will be present only during the time when the ambient
temperature is causing a fault condition. A sample display is shown below:
UNIT YYYYYYYY
HIGH AMBIENT TEMP

The unit will also be inhibited from starting any time


the temperature is above 128F.
Low Ambient Temp Fault
If the ambient temperature falls below the programmable Low Ambient Temp Cutout the chiller will shut
down with a controlled ramped shutdown. This fault
will only occur if the Low Ambient Cutout is ENABLED under the OPTIONS key. Restart can occur,
if demand allows, when temperature rises 2F above
the cutout. This fault cannot cause a lockout. The fault
display message will be present only during the time
when the ambient temperature is causing a fault condition. A sample display is shown below:
UNIT YYYYYYYY
LOW AMBIENT TEMP

LD10605

The unit is also inhibited from starting any time the


temperature is below the cutout plus 2F.
Low Leaving Chilled Liquid Temp Fault

In the descriptions of the fault displays that follow, the


fault message will show a YYYYYYY to indicate that
a system is in a FAULT condition and will restart
when the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.
If a control panel safety occurs after the VSD fault, but
before the fault is reset, the control panel fault is an
ALL FAULT of the VSD fault, meaning it will be registered as such in the History because it occurred while
the VSD was shutting down or while the systems were
shut down. All faults do not store operating data at the
time of the fault.
JOHNSON CONTROLS

The Low Leaving Chilled Liquid Temp Cutout helps to


protect the chiller from an evaporator freeze-up should
the chilled liquid temp drop below the freeze point.
This situation could occur under low flow conditions or
if the Micro Panel setpoint values are improperly programmed. Any time the leaving chilled liquid temperature (water or brine) drops below the programmable
cutout point, the chiller will fault and shutdown with a
controlled ramped shutdown. Restart can occur, if demand allows, when chilled liquid temperature rises 4F
above the cutout. This fault cannot cause a lockout. A
sample shutdown message is shown below:

245

MICROPANEL
FORM 201.23-NM1 (910)

UNIT YYYYYYYY
LOW LEAVING CHILLED LIQUID TEMP

The unit is inhibited from starting any time the chilled


liquid temperature is below the cutout plus 4F.
VSD Communications Failure Fault
The VSD Communications Failure is to prevent the
unit from trying to run, if the Chiller Control Board
never initializes communications with the VSD Logic
Board. The unit will also shut down with a controlled
ramped shutdown if the Chiller Control Board loses
communications with the VSD Logic Board while the
chiller is operating.
On power-up, the Chiller Microprocessor Board will
attempt to initialize communications with the VSD
Logic Board. The control panel will request data from
the VSD, which includes the number of compressors
and the VSD software version. Once these data points
have been received by the Chiller Control Board, and
have been successfully initialized, the Chiller Control
Board will not request them again. If the comms connection fails to occur, the Chiller Control Board will
prevent the chiller from operating and a fault message
will be displayed.
During normal operation, if the control panel Chiller
Control Board receives no valid response to messages
for 8 seconds, the unit will shut down all compressors
on a Comms fault. The Chiller Control Board will continue to send messages to the VSD while faulted. The
unit will be inhibited from starting until communications is established. The fault will automatically reset
when the Chiller Control Board receives a valid response from the VSD for a data request. Shown below
is an example of a Comms Failure fault message:

switch must be cycled off and on to clear the lockout


fault. See TABLE 17 for the programmable limits for
many of the cutouts.
When multiple systems are operating and a system
fault occurs, the running systems will ramp down and
the faulted system will be shut off and the previously
operating will restart if required after the fault clears
and/or the 120 second anti-recycle timer times out.
In the descriptions of the fault displays that follow, the
fault message will show a YYYYYYYY to indicate
that a system is in a FAULT condition and will restart when the fault clears, or LOCKOUT and will
not restart until the operator clears the fault using the
keypad. If a system safety is in effect, the message will
be displayed to the operator when the STATUS key is
pressed.
STATUS
KEY

LD10605

UNIT YYYYYYYY
VSD COMMUNICATIONS FAILURE

system safeties (faults)


System Safety (Fault) Operation
System safeties are faults that cause individual systems
to be shut down if a safety threshold is exceeded for 3
seconds. System faults are auto reset faults in that the
system will be allowed to restart automatically after the
120 second anti-recycle timer times out. The only exception is after any 3 faults on the same system occur
within 90 minutes, that system will be locked out on
the last fault. The lockout condition requires a manual
reset using the system switch. The respective system
246

In some cases, a control panel fault will occur after


a VSD fault, possibly during system shutdown or at
some later time. This is known as an ALL FAULT
and these faults will be recorded as such under the
HISTORY information stored at the instant of the primary fault. In some cases, this information may be
valuable in troubleshooting the primary fault. An example of the ALL FAULT history message is shown
on Page 263 under the HISTORY key. When an ALL
FAULT occurs, associated history information will
not be stored. If an additional fault does not occur, the
ALL FAULTS display will indicate NONE. In cases
where a VSD fault occurs during the rampdown of a
control panel fault (i.e.: low suction pressure, low water temp, etc.), the VSD fault will be stored as a new
JOHNSON CONTROLS

FORM 201.23-NM1 (910)

fault with the associated fault information stored at the


instant the VSD fault occurred (i.e.: IGBT Gate Drive,
Single Phase Input, VSD CT Plug, etc.). The control
panel fault that occurred prior to the VSD fault will be
stored with the associated complete data related to the
fault as a numerically lower numbered history in the
history buffers.
High Discharge Pressure Cutout (Software)
Fault
The High Discharge Pressure Cutout is a software fault.
A system will fault and shut down with a controlled
ramped shutdown on high discharge pressure when the
discharge pressure rises above 274 PSIG for 0.5 seconds. The system will be allowed to restart when the
discharge pressure falls to 259 PSIG. The system will
also be inhibited from starting if the pressure is above
259 PSIG. The fault message for this safety is shown
below:
SYS X YYYYYYYY HIGH DISCHARGE PRESSURE

X indicates the system and YYYYYYYY indicates


the system is in a FAULT condition and will restart
when the 120 second anti-recycle timer times out, or
LOCKOUT and will not restart until the operator
clears the fault using the keypad.
High Discharge Pressure Cutout
(HPCO) (Hardware) Fault
The mechanical High Pressure Cutout protects the
system from experiencing dangerously high discharge
pressure. A system will fault and shut down immediately when the mechanical high pressure cutout contacts open. The fault will occur immediately and not
wait 3 seconds, which is typical of most system faults.
The HPCO is wired in series with the VSD Run Signal
and will only be checked by the Chiller Control Board
when the system is running. The mechanical cutout
opens at 315 plus or minus 8 PSIG and closes at 230
plus or minus 10 PSIG. The Status display fault message for this system is shown below:
SYS X YYYYYYYY HPCO FAULT

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the 120 second anti-recycle timer times out or LOCKOUT and will not restart until the operator clears the
fault using the keypad.

JOHNSON CONTROLS

Low Suction Pressure Cutout (Software) Fault


The programmable Low Suction Pressure Cutout is
a secondary back-up for the flow switch and protects
against operation with low refrigerant charge, which
helps protect the chiller from an evaporator freeze-up,
should the system attempt to run with a low refrigerant
charge. The Status display fault message for this cutout is shown below:
SYS X YYYYYYYY LOW SUCTION PRESSURE

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the 120 second anti-recycle timer times out or LOCKOUT and will not restart until the operator clears the
fault using the keypad. Typically, the cutout will be set
at 24 PSIG for chilled water applications.
The cutout is ignored for the first 30 seconds of system
run time. During the next 3 minutes of run time the
cutout point is linearly ramped from 10% of the cutout
value up to the programmed cutout point. If at any time
during the first 3 minutes of operation the suction pressure falls below the ramped cutout point, the system
will shut down with a controlled ramped shutdown.
The cutout pressure during operating periods of 30 seconds to 210 seconds is ramped and can be calculated
by:
Cutout = (Programmed Cutout x Run Time)1.2 PSIG

200
After the first 3 minutes and 30 seconds of run time, if
the suction pressure falls below the cutout as a result
of a transient in the system, a transient timer is set at
30 seconds and a linearly ramped cutout is set starting
at 10% of the programmed cutout. If over the next
30 seconds, the suction pressure does not stay above
the ramped cutout, which ramps between 10% of the
cutout and the programmed cutout over the 30 second
period, the system will fault on low suction pressure.
Low Motor Current Cutout Fault
The Motor Current Cutout shuts the system down with
a controlled ramped shutdown when the microprocessor detects the absence of motor current (less than 10%
FLA), usually indicating that a compressor is not running. This safety is ignored for the first 10 seconds of
operation.

247

MICROPANEL
FORM 201.23-NM1 (910)

The status display fault message for this safety is


shown below:
SYS X YYYYYYYY LOW MOTOR CURRENT

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the 120 second anti-recycle timer times out or LOCKOUT and will not restart until the operator clears the
fault using the keypad.
High Differential Oil Pressure Cutout Fault
The High Differential Oil Pressure Cutout protects the
compressor from low oil flow and insufficient lubrication, possibly from a dirty oil filter. A system will fault
and shut down with a controlled ramped shutdown
when its Discharge to Oil Differential Pressure rises
above the cutout of 65 PSID. This safety is ignored
for the first 90 seconds of run time. This safety measures the pressure differential between discharge and
oil pressure, which is the pressure drop across the oil
filter. The Status display fault message for this safety
is shown below:
SYS X YYYYYYYY HIGH DIFF OIL PRESSURE

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the 120 second anti-recycle timer times out or LOCKOUT and will not restart until the operator clears the
fault using the keypad.
Low Differential Oil Pressure Cutout Fault
The Low Differential Oil Pressure Cutout protects
the compressor from low oil flow and insufficient lubrication. A system will fault and shut down with a
controlled ramped shutdown when its differential between oil and suction pressure falls below the cutout.
This safety assures that the compressor is pumping
sufficiently to push oil through the oil cooling circuit
and through the internal compressor lubrication system. The Status display fault message for this safety is
shown below:
SYS X YYYYYYYY LOW DIFF OIL PRESSURE

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the 120 second anti-recycle timer times out or LOCKOUT and will not restart until the operator clears the
fault using the keypad.

248

The safety is ignored for the first 60 seconds of run


time. After the first 60 seconds of operation, the cutout is linearly ramped from 0 PSID to 30 PSID in 5 to
10 minutes based on ambient temperature. See TABLE
13 for the ramp times for the given ambient temperatures.
TABLE 13 - low differential oil pressure
cutout
AMBIENT TEMPERATURE

RAMP
TIME

> 50F

5 Minutes

> 45F

6 Minutes

> 40F

7 Minutes

> 35F

8 Minutes

> 30F

9 Minutes

>=30F

10 Minutes

A 30 second safety bypass below 50 Hertz is employed


during rampdown. The bypass is primarily needed
under conditions where another compressor is being brought on and the running compressor is being
ramped down to 5 Hertz to add the additional compressor due to load requirements. Under these conditions,
the slow speed of the running compressor(s) causes the
oil differential to become very low, especially if the
water temperature is high and the suction pressure is
high. The bypass assures the compressor(s) will not
trip on a nuisance low oil differential fault.
High Discharge Temperature Cutout Fault
The High Discharge Temperature Cutout protects the
motor and compressor from overheating. A system
will fault and shut down with a controlled ramped
shutdown when its Discharge Temperature rises above
250F. A system will also be inhibited from starting if
the discharge temperature is above 200F. The Status
display fault message for this safety is shown below:
SYS X YYYYYYYY HIGH DSCHARGE TEMP

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the 120 second anti-recycle timer times out or LOCKOUT and will not restart until the operator clears the
fault using the keypad.
High Oil Temperature Cutout Fault
The High Oil Temperature Cutout protects the compressor from insufficient lubrication. A system will
fault and shut down with a controlled ramped shut-

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

down when its oil temperature rises above 225F. The


system will be inhibited from starting if the oil temperature is above 175F. The Status display fault message
for this safety is shown below:
SYS X YYYYYYYY HIGH OIL TEMP

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.
Low Suction Superheat Cutout Fault
The Low Suction Superheat Cutout helps protect the
compressor from liquid floodback due to low suction
superheat. This safety is ignored for the first 30 seconds of compressor operation. Low suction superheat
will fault a system when any one of the following conditions occur:
After the first 30 seconds of run time, if the suction
superheat falls below 2.0F, the discharge superheat
is less than 15F, and the run time is less than 5
minutes, the superheat safety will be ignored for the
next 30 seconds followed by setting the superheat
cutout to 0F and linearly ramping it up to 2.0F over
the next 60 seconds. If at any time during these 60
seconds the suction superheat falls below the ramped
cutout, the system will fault and shut down with a
controlled ramped shutdown.
If the suction superheat less than 2F, the discharge
superheat less than 15F for 10 seconds, and the run
time is equal to or more than 5 minutes, the system
will fault and shutdown with a controlled ramped
shutdown.
If the suction superheat less than 0.5F and discharge
superheat is more than 15F for 60 seconds and run
time equal to or more than 5 minutes, the system
will fault and shutdown with a controlled ramped
shutdown.
If suction superheat less than 5F for 10 minutes,
the system will fault and shutdown with a controlled
ramped shutdown.
The Status display fault message for this safety is
shown below:
SYS X YYYYYYYY LOW SUCTION SUPERHEAT

X indicates the system and YYYYYYYY indicates the


system is FAULT and will restart after the 120 second anti-recycle timer times out or LOCKOUT and
will not restart until the operator clears the fault.
JOHNSON CONTROLS

Low Discharge Superheat Cutout Fault


The Low Discharge Superheat Cutout helps protect the
compressor primarily from liquid floodback through
the economizer line due to a high flash tank level. It
also provides protection from liquid floodback through
the suction line in conjunction with the low superheat
safety. This safety is ignored for the first 5 minutes of
compressor operation.
After the first 5 minutes of run time, if the discharge
superheat falls below 10.0F for 5 minutes, the system will fault and shut down with a controlled ramped
shutdown.
The Status display fault message for this safety is
shown below:
SYS X YYYYYYYY LOW DISCHARGE SUPERHEAT

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the 120 second anti-recycle timer times out or LOCKOUT and will not restart until the operator clears the
fault using the keypad.
Sensor Failure Cutout Fault
The Sensor Failure Cutout prevents the system from
running when a critical sensor (transducer, level sensor, or motor winding temp sensor) is not functioning properly and reading out of range. This safety is
checked at start-up and will prevent the system from
running if one of the sensors has failed.
The sensor failure safety will also fault and shutdown
a system while in operation, if a safety threshold is exceeded or a sensor reads out of range (high or low).
Following is the Status display fault message.
SYS X YYYYYYYY SENSOR FAILURE:
ZZZZZZZZZZZZ

X indicates the specific system.


YYYYYYYY will either indicate the
system is in a FAULT condition and
will restart when the fault clears, or
LOCKOUT after 3 faults and will
not restart until the operator clears the
fault using the keypad.

249

MICROPANEL
FORM 201.23-NM1 (910)

ZZZZZZZZZZZ indicates the failed sensor below:






High Flash Tank Level Cutout Fault


The Flash tank level Cutout prevents the system from
running when the liquid level in the flash tank is too
high. The safety will be ignored for the first 15 seconds of system operation.

SUCT PRESS
OIL PRESS
DSCH PRESS
LEVEL SENSOR
MOTOR TEMP X *

A fault will occur if the tank level is greater than 85%


for 10 seconds.

*The Unit Setup Mode allows a specific motor temperature sensor


to be ignored, if it fails.

The start inhibit thresholds for each sensor are shown


in TABLE 14.
TABLE 14 - start inhibit sensor
thresholds
LOW
SENSOR

THRESHOLD

HIGH
THRESHOLD

SUCTION
TRANSDUCER

0.3VDC

4.7VDC

OIL
TRANSDUCER

0.3VDC

4.7VDC

DISCHARGE
TRANSDUCER

0.3VDC

4.7VDC

LEVEL SENSOR

3.0ma

21.0ma

MOTOR TEMP.
SENSOR

0F

240F

High Motor Temperature Cutout Fault


The High Motor Temperature Cutout prevents a compressor from running when its motor temperature is
too high. A system will fault and shut down when
any compressor motor temperature sensor rises above
250F. The system will be inhibited from starting if
its motor temperatures sensors indicate temperatures
above 240F. If any single temperature sensor is being
ignored under the Unit Set-up Mode, that sensor will
not be utilized when evaluating motor temperature.
Below is a sample Status display fault message:

Below is a sample Status fault display fault message:


SYS X YYYYYYYY HIGH FLASH TANK LEVEL

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the 120 second anti-recycle timer times out or LOCKOUT and will not restart until the operator clears the
fault using the keypad.
System Control Voltage Cutout Fault
The System Control Voltage Cutout alerts the operator
the 115VAC Control voltage to one of the systems is
missing. This could be due to a system fuse that has
been removed or is blown. The affected system will
fault and shut down immediately when the 115VAC
supply is lost.
The safety will not shut down a system if the UNIT
switch is OFF, which electrically removes the 115VAC
to all systems. The safety is only used to indicate a
situation where a single system is missing the 115VAC.
The safety will not cause a lockout and the system fault
will reset when power is returned. A sample message
is shown below:
SYS X YYYYYYYY CONTROL VOLTAGE

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.

SYS X YYYYYYYY HIGH MOTOR TEMP

X indicates the system and YYYYYYY indicates the


system is in a FAULT condition and will restart when
the fault clears or LOCKOUT and will not restart until the operator clears the fault using the keypad.

250

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

status key
STATUS
KEY

8
LD10605

Status Key Operation


The STATUS key displays the current chiller or system
operational status. The messages displayed include running status, cooling demand, system faults, unit faults,
VSD faults, unit warnings, external device status,
load limiting, anti-recycle timer, status of unit/system
switches, and a number of other messages. Pressing
the STATUS key will enable the operator to view the
current status of the chiller. The display will show one
message relating to the highest priority information
as determined by the microprocessor. The STATUS
key must be pressed twice to view both System 1/2 and
System 3/4 data. There are three types of status data,
which may appear on the display:
General Status messages
Unit Safeties
System Safeties.
When power is first applied to the control panel, the
following message displaying York International
Corporation, the EPROM version, date, and time will
be displayed for 2 seconds, followed by the appropriate
general status message:

JOHNSON CONTROLS

(c)2004 YORK INTERNATIONAL CORPORATION


C.XXX.XX.XX 18-SEPT-2005 12:45: AM

Unit status messages occupy 2 lines of the Status message display. If no unit status message applies, individual status messages for each system will be displayed.
On 3 and 4 compressor units, the STATUS key must be
pressed twice to display the status of all systems.
Any time the STATUS key is pressed or after the
EPROM message disappears at power-up, a status display indicating chiller or system status will appear.
Multiple STATUS messages may appear and can be
viewed by pressing the STATUS key repeatedly to allow scrolling through as many as three STATUS messages, that could possibly be displayed at any time on
a 2 compressor chiller or 4 messages that could be displayed on a 3 or 4 compressor chiller.
Examples of the typical Status messages are shown in
the next topic

251

MICROPANEL
FORM 201.23-NM1 (910)

General Status Messages


UNIT STATUS
MANUAL OVERRIDE

This message indicates the chiller is operating in


MANUAL OVERRIDE mode. This message is a priority message and cannot be overridden by any other
STATUS message. When in Manual Override, no other
status message will ever be present.
UNIT STATUS
UNIT SWITCH OFF SHUTDOWN

This message indicates the UNIT SWITCH is in the off


position and not allowing the unit to run.
UNIT STATUS
DAILY SCHEDULE SHUTDOWN

This message indicates that either the daily or holiday


schedule programmed is keeping the chiller from running.
UNIT STATUS
REMOTE CONTROLLED SHUTDOWN

This message indicates that either an ISN or RCC has


turned the chiller off and is not allowing it to run.
UNIT STATUS
FLOW SWITCH SHUTDOWN

This message indicates the flow switch is not allowing


the chiller to run. There is a 1 second delay on this
safety to assure the flow switch did not momentarily
open.
UNIT STATUS
VSD COOLING SHUTDOWN

This message indicates the chiller is shutdown, but


running all the condenser fans, VSD glycol pump, and
VSD fan in an effort to bring the internal VSD ambient
temperature down to an acceptable level before allowing the chiller to start.
SYS X REMOTE RUN CONTACT IS OPEN

This message indicates the remote start/stop contact


between 2-15 or 2-16 of the 1TB terminal block is
open. There is a 1 second delay on this safety to assure
the remote contacts did not momentarily open.

252

SYS X SYSTEM SWITCH IS OFF

This message indicates the system switch (software via


keypad) is turned off. The system will not be allowed
to run until the system switch is turned ON via the keypad.
SYS X NOT RUNNING

This message indicates the system is not running because the chilled liquid is below the setpoint or the
micro has not loaded the lead system far enough into
the loading sequence to bring the lag system on. This
message will be displayed on the lag system until the
loading sequence is ready for the lag system to start.
SYS X COOLING DEMAND SHUTDOWN

This message is only displayed in the Normal Shutdown History display to indicate a capacity control
shutdown.
SYS X COMPRESSOR RUNNING

This message indicates the system is running as a result


of cooling demand.
SYS X SHUTTING DOWN

The compressor shutting down message indicates the


respective system is ramping down in speed prior to
shutting off. This message is displayed after the software run signal is disabled until the VSD notifies the
Chiller Control Board the compressor is no longer running.
SYS X ANTI-RECYCLE TIMER

= XXX SEC

This message indicates the amount of time left on the


respective system anti-recycle timer and the system is
unable to start until the timer times out.
SYS X DISCHARGE PRESSURE LIMITING

The Discharge Pressure Limiting message indicates


the discharge pressure load limit or discharge pressure
unloading is in effect.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SYS X SUCTION PRESSURE LIMITING

The Suction Pressure Limiting message indicates the


suction pressure load limit or suction pressure unloading is in effect.
SYS X MOTOR TEMP LIMITING

The Motor Temp Limiting message indicates the motor


temp load limit or motor temp unloading is in effect.
SYS X MOTOR CURRENT LIMITING

The motor current limiting message indicates the motor current load limit or motor current unloading is in
effect.
SYS X PULLDOWN MOTOR CURRENT LIMITING

The pulldown motor current limiting message indicates


the pulldown motor current load limit or pulldown
motor current unloading is in effect based on the programmed setpoint.
SYS X ISN CURRENT LIMITING

The ISN Current Limiting message indicates the motor


current load limit or motor current unloading is in effect through the use of the YORKTalk setpoint.
SYS X REMOTE MOTOR CURRENT LIMITING

The Remote Motor Current Limiting message indicates


the motor current load limit or motor current unloading
is in effect through the use of the remote setpoint offset. The setpoint may be offset using a remote voltage
or a current signal. The remote current limit must be
activated for this function to operate.
SYS X VSD BASEPLATE TEMP LIMITING

The VSD Baseplate Temp Limiting message indicates


the VSD Baseplate temp is high and load limit or unloading is in effect.

JOHNSON CONTROLS

SYS X VSD INTERNAL AMBIENT TEMP LIMITING

The VSD Internal Ambient Temp Limiting message indicates the VSD internal ambient temp is high and load
limit or unloading is in effect.
SYS X SOUND LIMITING

The sound limiting message indicates the sound load


limit is in effect based on the locally programmed
sound limit from the keypad. The sound limit must be
activated for this function to operate.
SYS X ISN SOUND LIMITING

The ISN sound limiting message indicates the sound


load limit is in effect based on the ISN transmitted
sound limit setpoint. The sound limit must be activated
for this function to operate.
SYS X REMOTE SOUND LIMITING

The Remote sound limiting message indicates the sound


load limit is in effect based on the Remote controlled
sound limit setpoint. The setpoint may be offset using
a remote voltage or current signal. The sound limit option must be activated for this function to operate.
Unit Safety (Fault) Status Messages
A complete listing of the unit safeties and the corresponding status messages is provided on Page 245.
System Safety (Fault) Status Messages
A complete listing of the system safeties and the corresponding status messages is provided on Page 246.
VSD Safety (Fault) Status Messages
A complete listing of VSD safeties and the corresponding status messages is provided on Page 237.
Unit Warning Messages
A complete listing of the unit warnings and the corresponding status messages is provided on Page 243.

253

MICROPANEL
FORM 201.23-NM1 (910)

unit data key


unit data
Key

LD10605

General
The UNIT DATA key provides the user with displays
of unit temperatures, and unit related data. Displays
can be selected by repeatedly pressing the UNIT DATA
key or the or Arrow Keys.
Unit Data Key Operation
The first key press displays Evaporator Leaving and
Return Chilled Liquid Temps.
UNIT CHILLED LIQUID LEAVING = XXX.X F

ENTERING = XXX.X F

The next key press of the UNIT DATA key or the


(ARROW) key displays the ambient air temperature.
UNIT
OUTSIDE AMBIENT AIR TEMP = XXX.X F

The next key press will display the time remaining on


the load and unload timers.
UNIT

254

The next key press displays the error in temperature


between the actual leaving chilled liquid temperature
and the setpoint temperature. The display also shows
the rate of change of the chilled liquid temperature.
UNIT

TEMP ERROR = XXX.X F

RATE = XXX.X F/M

The next key press displays the system designated as


the lead system and the Flow Switch status (ON or
OFF).
UNIT

LEAD SYSTEM NUMBER = X

FLOW SWITCH = XXX

The next key press displays the status of the evaporator


pump and heater, where XXX is either ON or OFF.
UNIT

EVAP PUMP RUN = XXX

EVAP HEATER = XXX

LOAD TIMER = XXX SEC


UNLOAD TIMER = XXX SEC

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

The next key press displays the status of Active Remote Control.
UNIT ACTIVE REMOTE CONTR0L = XXXXXX
TYPE: RCC ISN CURR TEMP SOUND

XXXXX is either ACTIVE or NONE.


If no remote keys are active, the items on the second
line are all blanked out. Any remote items that are active will be displayed, while the inactive items will be
blanked out.
The types of remote control are listed below:
NONE - No remote control is actively controlling
the chiller; however, remote monitoring by a remote
device may still be active.

RCC - A Remote Control Center is providing remote


control. The chiller is in remote mode.
ISN - YorkTalk via ISN. The chiller in remote
mode.
CURR - Remote Current Limiting is enabled.
TEMP - Remote Temperature Reset is enabled.
SOUND - Remote Sound Limiting is enabled.
The next key press displays the sound limit values as
set under the PROGRAM key by the Local, ISN, and
the Remote Sound Limit Inputs. Any sound limits that
are inactive will display XXX instead of a numeric
value.
UNIT SOUND LIMIT

ISN = XXX

LOCAL = XXX %
REMOTE = XXX %

JOHNSON CONTROLS

255

MICROPANEL
FORM 201.23-NM1 (910)

system data keys 1 through 4

SYSTEM 1
DATA KEY
SYSTEM 2
DATA KEY

SYSTEM 3
DATA KEY
SYSTEM 4
DATA KEY

LD10605

General
The data keys provide the user with many displays of
individual system temperatures, pressures, and other
operating data. These keys have multiple displays,
which can be seen by repeatedly pressing the SYSTEM
DATA or the or (Arrow) keys. An explanation
of each key and its messages is provided below.
System 1 Data Key Operation
The SYSTEM 1 DATA key provides the user with access to System 1 operating parameters. The following
is a list of the data in the order in which it appears.
The first key press of the SYSTEM X DATA key displays all of the measured system pressures (oil, suction, and discharge).
SYS 1 PRESSURES

OIL = XXXX PSIG

SUCTION = XXXX DISCHARGE = XXXX PSIG

The second key press of the SYSTEM DATA key or the


(DOWN ARROW) key displays all of the measured
system temperatures (oil, suction, and discharge).
SYS 1 TEMPERATURES

The next key press displays the suction temperature


and all of the calculated suction temperatures (saturated suction and system superheat).
SYS 1 SUCTION

TEMP = XXX.X F

SUPERHEAT = XXX.X SAT TEMP = XXX.X F

The next key press displays the discharge temperature


and all of the calculated discharge temperatures (saturated discharge and discharge superheat).
SYS 1 DISCHARGE

TEMP = XXX.X F

SUPERHEAT = XXX.X SAT TEMP = XXX.X F

The next key press displays the System 1 motor thermistor temperatures.
SYS 1 MOTOR TEMPS
T2 = XXX.X F

T1 = XXX.X F
T3 = XXX.X F

If any motor temp sensor is being ignored, (selectable under Unit Set-up
Mode), that sensors value will be
displayed as XXXXX.

OIL = XXX.X F

SUCTION = XXX.X DISCHARGE = XXX.X F

256

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

The next key press indicates the % of compressor loading and status of the economizer solenoid as determined by the operating frequency.
SYS 1 COMPRESSOR

SPEED = XXX.X %

ECONOMIZER SOLENOID = XXX

XXX indicates whether the economizer solenoid is either ON or OFF.


The next key press displays the liquid level in the flash
tank and an indicator of the % the Flash Tank Feed
Valve is open.
SYS 1 FLASH TANK

LEVEL = XXX.X %

FEED VALVE PERCENT OPEN = XXX.X %

The next key press displays the system suction superheat and an indicator of the % the Flash Tank Drain
Valve is open.
SYS 1

SUCTION SUPERHEAT = XXX.X F

DRAIN VALVE PERCENT OPEN = XXX.X %

The next key press displays the system fan stage and
the status of the compressor heater.

The next key press displays the system run time in


days, hours, minutes, and seconds.
SYS 1 RUN TIME
XX DAYS XX HOURS XX MINUTES XX SECONDS

The next key press displays the status of several system


signals.
SYS 1 RUN SIGNALS RELAY = XXX
RUN PERM = XXX

SOFTWARE = XXX

XXX indicates either ON or OFF.


System 2 through 4 Data Key Operation
These keys function the same as the SYSTEM 1 DATA
key except that it displays data for System 2 through
4.
On a 2 compressor system, the SYSTEM 3 and SYSTEM 4 data keys will display the following messages:
SYS 3 DATA NOT AVAILABLE
SYS 4 DATA NOT AVAILABLE

SYS 1 CONDENSER FANS ON = X


COMPRESSOR HEATER = XXX

X equals the number of fans ON. XXX indicates either


the heater is ON or OFF.

JOHNSON CONTROLS

257

MICROPANEL
FORM 201.23-NM1 (910)

Sensor Displays
TABLE 15 lists all the sensors attached to the control
board associated with system data keys. The minimum
and maximum values displayed on the micro display
are provided.
If values exceed the limits in the table, a < (less than)
or > (more than) sign will be display along with the
minimum or maximum value.
TABLE 15 - sensor min/max outputs
SENSOR

TYPE

MIN.

MAX.

Suction
Pressure

Transducer

0.0 PSIG

125.0 PSIG

Oil
Pressure

Transducer

0.0 PSIG

275.0 PSIG

Discharge
Pressure

Transducer

0.0 PSIG

275.0 PSIG

Capacitance

0.0%

100 %

-19.1F

110.2F

-19.1F

110.2F

-4.6F

137.9F

-4.1F

132.8F

40.3F

302.6F

40.3F

302.6F

-30.0F

302.0F

0%

100 %

0%

100 %

0%

100 %

Flash Tank
Level
Leaving Chilled
Liquid Temp.

Thermistor
3Kohm

Return Chilled
Liquid Temp.

Thermistor

Ambient Air
Temp.

Thermistor

Suction
Temp.

Thermistor

Oil Temp.

Thermistor

Discharge
Temp.

Thermistor

Compressor
Motor Temp.

Thermistor

Remote Temp.
Reset
Remote
Current Limit
Remote
Sound Limit

258

3Kohm

10Kohm
3Kohm
50Kohm
50Kohm
10Kohm
4-20mA/2-10VDC
0-20mA/0-10VDC
4-20mA/2-10VDC
0-20mA/0-10VDC
4-20mA/2-10VDC
0-20mA/0-10VDC

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

vsd data key

VSD
DATA KEY
LD10605

General

VSD COMP 1 = XXX AMPS

= XXX %FLA

The VSD DATA key provides the user with displays of


VSD temperatures, voltages, currents, and other operating data. This key has multiple displays, which can
be seen by repeatedly pressing the VSD DATA or the
or (Arrow) keys. An explanation of each message is provided below.

= XXX %FLA

VSD Data Key Operation


The first VSD DATA key press displays the actual VSD
Output Frequency and Command Frequency.
VSD FREQUENCY

ACTUAL = XXX.X HZ
COMMAND = XXX.X HZ

The second key press of the VSD DATA key or the


(ARROW) key displays the compressor % FLA and
calculated currents in amps for systems 1 and 2. The
calculated currents are approximate and some error
can be expected. Also keep in mind that measuring
inverter PWM current is difficult and meter error can
be significant.

JOHNSON CONTROLS

COMP 2 = XXX AMPS

For 3 and 4 compressor units only, the second key


press will display the following message for systems
1 and 3:
VSD COMP 1 = XXX AMPS

= XXX %FLA

= XXX %FLA

COMP 3 = XXX AMPS

For 3 and 4 compressor units only, the next key press


displays the compressor %FLA and currents for systems 2 and 4. 3 compressor units will have the 4th
compressor information blanked out.
VSD COMP 2 = XXX AMPS

= XXX %FLA

= XXX %FLA

COMP 4 = XXX AMPS

259

MICROPANEL
FORM 201.23-NM1 (910)

The next key press displays the current limit values


set locally on the panel under the PROGRAM key, remotely by an ISN, and remotely by the Current Limit
input. Any current limits that are inactive will display
XXX instead of a numeric value.
VSD CURRENT LIMIT
ISN = XXX

LOCAL = XXX %FLA


REMOTE = XXX %FLA

The next key press displays DC Bus voltage for 2 and 3


compressor units. On 4 compressor units, the 2nd message will apply, since two DC Bus voltages are present
(Systems 1/3 and 2/4).
VSD

DC BUS VOLTAGE = XXX VDC

VSD DC BUS VOLTAGES BUS 1 = XXX VDC


BUS 2 = XXX VDC

The next key press displays the Control Panel/VSD Internal Ambient Temperature and VSD Cooling Pump/
Fan Status. YYY will indicate ON or OFF.
VSD

INTERNAL AMBIENT TEMP = XXX.X F

COOLING SYSTEM STATUS = YYY

The next key press displays the IGBT highest baseplate


temperature for 2 and 3 compressor units. 4 compressor units display temperatures for Systems 1/3 (T1)
and Systems 2/4 (T2).

The next key press displays the state of the Precharge


signal, where XXX is either ON or OFF. The first display is for 2 and 3 compressor units, the second display
shown is for 4 compressor units where Precharge 1 is
for compressors 1 and 3 DC Bus and Precharge 2 is for
compressors 2 and 4 DC Bus.
VSD

PRECHARGE SIGNAL = XXX

VSD

PRECHARGE 1 SIGNAL = XXX

VSD

PRECHARGE 2 SIGNAL = XXX

The next key press displays the setting of the VSDs


105% FLA overload potentiometer for Compressor
#1 and 2. The settings are determined by the adjustment of the overload potentiometers on the VSD Logic
Board. These pots are factory set and should not require changing unless the circuit board is replaced. See
TABLE 35 for factory settings.
VSD

COMP 1 MOTOR OVERLOAD = XXX AMPS

COMP 2 MOTOR OVERLOAD = XXX AMPS

The next key press displays the setting of the VSDs


105% FLA potentiometer for Compressor #3 and #4 (3
and 4 compressor units only). The second line will be
blanked out on 3 compressor units.
VSD

COMP 3 MOTOR OVERLOAD = XXX AMPS

COMP 4 MOTOR OVERLOAD = XXX AMPS

VSD IGBT BASEPLATE TEMPS T1 = XXX F


260

T2 = XXX F

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

operating hours / start counter key

operating hours/
start counter
Key

8
LD10605

Compressor operating hours and compressor starts are


displayed with a single key press. The maximum value
for both hours and starts is 99,999, at which point they
will roll over to 0. A single display is available under
this key and is displayed below. On 2 and 3 compressor units, the data and compressor designators for compressors not present are blanked out.
HOURS 1=XXXXX, 2=XXXXX, 3=XXXXX, 4=XXXXX
`

START 1=XXXXX, 2=XXXXX, 3=XXXXX, 4=XXXXX

JOHNSON CONTROLS

261

MICROPANEL
FORM 201.23-NM1 (910)

history key

history
key

LD10605

History Key Operation

Normal Shutdowns History

The HISTORY key provides the user access to many


unit and system operating parameters captured at the
instant a unit or system safety (fault) shutdown occurs.
The history buffer will also capture system data at the
time of normal shutdowns such as cycling shutdowns.
When the HISTORY key is pressed the following
screen is displayed:

If the NORMAL SHUTDOWNS History is selected,


the following screen will be displayed:

HISTORY

CHOOSE HISTORY TYPE

XXXXXXXXXXXXXXXXXXXXXXXXXXXX

The and (arrow) keys allow choosing between NORMAL SHUTDOWNS and FAULT SHUTDOWNS. Fault shutdowns provide information on
safety shutdowns, while Normal shutdowns provide
chiller cycling information on temperature (demand),
cycling, remote, system switch, etc., shutdowns that
are non-safety related shutdowns. Once the selection
is made, the (ENTER) key must be pressed to enter
the selection.

NORM HIST XX 18-JUN-20004 10:34:58 AM


YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY

XX is the normal shutdown number. The display will


provide date and time of the shutdown and the reason
for the cycling shutdown (YYY.).
The operator can view any of the stored 20 single display normal shutdown history buffers. History buffer
number 1 provides the most recent shutdown information and buffer number 20 is the oldest safety shutdown
information saved. The and (arrow) keys allow
scrolling between each of the history buffers. The
(arrow) key scrolls to the next normal history shutdown and the (ARROW) key scrolls to the previous
normal history shutdown.
The following display will typically be displayed on a
normal shutdown due to shutdown on lack of cooling
demand.
NORM HIST XX 18-JUN-20004 10:34:58 AM
SYS X COOLING DEMAND SHUTDOWN

262

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Fault Shutdowns History


If the FAULT SHUTDOWNS History is selected, the
following screen will be displayed:
FAULT HIST XX 18-JUN-20004 10:34:58 AM
YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY

XX is the FAULT HISTORY shutdown number. The


display will provide the date, time, and a description of
the specific type of fault that occurred (YYY.).
The operator can view any of the stored 10 fault history
buffers. History buffer number 1 provides the most
recent safety shutdown information and buffer number 10 is the oldest safety shutdown information saved.
The and arrow keys allow scrolling between
each of the FAULT HIST buffers 1 through10. The
(UP) and (DOWN) arrow keys can be used to scroll
forwards and backwards through the data in a specific
history buffer, once it is displayed.
There is a large amount of data provided under each
history. Rather than scroll sequentially through the
data in a history, which is possible using the arrow
key, the use of a combination of the , , and
arrow keys allows fast scrolling to specific data the
user desires to view. To use this feature, the user needs
to be aware the and arrow keys allow scrolling to
the top of the data subgroups. Once a specific history
is selected, the history data is divided under the subgroups of Unit Data, VSD Data, System Data, Hours/
Starts, Setpoints, Options, and Program data. The
and arrow keys allow moving to the first display
under the next or previous subgroup at any time. Once
the first display of a subgroup is displayed, the and
arrow keys allow scrolling though the data in the
subgroup. The arrow key allows scrolling though
the data from first to last. When the last piece of data
is displayed, the next press of the arrow key scrolls
to the first piece of data in the next subgroup. The
arrow key allows going to the previous display.
Listed below is a description of the fault data displays
and their meaning. Data will be displayed in a specific
order starting with the Status Display (System Faults
only), Fault Display, All Fault Display, Unit Data, VSD
Data, System Data, Operating Hours/Starts, Setpoints,
Options, and Program Values at the time of the fault.

JOHNSON CONTROLS

Status Fault Type


SYS X COMPRESSOR RUNNING
SYS X YYYYYYYY HIGH DIFF OIL PRESSURE

This message indicates the type of system fault. This


screen is skipped if a UNIT Fault caused the shutdown.
Unit Fault Type
UNIT FAULT
LOW AMBIENT TEMP

This message indicates the type of unit fault. This


screen is skipped if a SYSTEM Fault caused the shutdown.
All Fault Data
FAULT HIST XX ALL FAULTS ZZ OF WW
YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY

The ALL FAULT display indicates whether a fault


occurred while the unit is shutting down on another
fault.
If a control panel fault occurred while the unit is shutting down on a VSD fault before it is reset, the control
panel fault is an ALL FAULT of the VSD fault.
If another VSD fault occurs while the unit is shutting
down on a VSD fault, the next VSD fault will be registered as an ALL FAULT of the VSD fault.
If a VSD fault occurs during the ramp down shutdown
of a control panel fault, the VSD fault is registered as a
new fault, not an ALL FAULT
XX is the history number, YYY is the ALL FAULT
description, ZZ is the ALL FAULT number and WW
is the total number of All Faults for the current history. Sometimes, multiple faults may occur during the
shutdown and multiple displays will be observed when
scrolling through the data using the arrow. In most
cases, the ALL FAULT display will indicate NONE.
The ALL FAULT display will only indicate the cause
of the fault. No additional chiller information will be
displayed under the ALL FAULT, since a snapshot of
all chiller data was taken at the time of the first fault.

263

MICROPANEL
FORM 201.23-NM1 (910)

Unit Data

Active Remote Control Status

Evaporator Leaving and Return Chilled Liquid


Temps
This message indicates the leaving and entering chilled
liquid temperatures at the time of the fault.
Ambient Air Temperature
UNIT
OUTSIDE AMBIENT AIR TEMP = XXX.X F

This message indicates the ambient air temperature at


the time of the fault.
Load / Unload Timers
UNIT

LOAD TIMER = XXX SEC


UNLOAD TIMER = XXX SEC

This message indicates remaining time on the load and


unload timers at the time of the fault.
Chilled Liquid Temperature Error and Rate of
Change
UNIT

TEMP ERROR = XXX.X F

RATE = XXX.X F/M

This message indicates the temperature error between


the actual and the programmed setpoint at the time of
the fault and the rate of temperature change.
Programmed Lead System Selection and Flow
Switch Status
UNIT

LEAD SYSTEM NUMBER = X

FLOW SWITCH = XXX

UNIT ACTIVE REMOTE CONTR0L = XXXXXX

This message indicates whether the system was operating under Active Remote Control (RCC, ISN, LOAD,
TEMP, or SOUND) or standard control (NONE) at the
time of the fault.
UNIT SOUND LIMIT

ISN = XXX

LOCAL = XXX %
REMOTE = XXX %

This message indicates that sound limiting was in effect, the amount, and whether it was local or remotely
limited.
VSD Data
VSD Actual and Command Frequency
VSD FREQUENCY

ACTUAL = XXX.X HZ
COMMAND = XXX.X HZ

This message indicates the VSD actual operating frequency and the command frequency at the time of the
fault. Actual and command may not match due to load/
unload timers, limitation of 1 Hz per load/unload increment, and to allowable acceleration/deceleration of the
motor.
VSD COMP 1 = XXX AMPS

= XXX %FLA

COMP 2 = XXX AMPS

= XXX %FLA

Compressor AMPS and %FLA


The message indicates the compressor %FLA and currents for systems 1 and 2 at the time of the fault.

This message indicates the designated lead system at


the time of the fault and whether the flow switch was
ON (Closed) or OFF (Open) at the time of the fault.

COMP 1

= XXX AMPS

= XXX %FLA

COMP 3

= XXX AMPS

= XXX %FLA

COMP 2

= XXX AMPS

= XXX %FLA

Evaporator Pump and Evaporator Heater


Status

COMP 4

= XXX AMPS

= XXX %FLA

UNIT

EVAP PUMP RUN = XXX

EVAP HEATER = XXX

These messages indicate the compressor %FLA and


currents for systems 3 and 4 at the time of the fault.
For 3 compressor units, the #4 compressor information
is blanked out.

This message indicates the status of the evaporator


pump and the evaporator heater at the time of the fault.
XXX indicates ON or OFF.

264

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

VSD Current Limit


VSD CURRENT LIMIT
ISN = XXX

LOCAL = XXX %FLA


REMOTE = XXX %FLA

This message displays the current limit values as set


locally, by an ISN, or a remote current limiting input at
the time of the fault.
DC BUS Voltage
VSD

DC BUS VOLTAGE = XXX VDC

DC BUS VOLTAGES

BUS 1 = XXX VDC

BUS 2 = XXX VDC

This message displays the DC Bus voltage at the time


of the fault. On 4 compressor units, the 2nd message
will apply since two DC Bus voltages are present (1/3
and 2/4) at the time of the fault.
VSD Internal Ambient Temp

Compressor #1 and #2, 105% FLA Motor


Overload Current Setting
VSD

COMP 1 MOTOR OVERLOAD = XXX AMPS

COMP 2 MOTOR OVERLOAD = XXX AMPS

This message displays the setting of the VSDs 100%


FLA potentiometer for Compressor #1 and #2 at the
time of the fault.
Compressor #3 and #4, 105% FLA Current
Setting
COMP 3 MOTOR OVERLOAD

= XXX AMPS

COMP 4 MOTOR OVERLOAD

= XXX AMPS

This message displays the setting of the


VSDs 100% FLA potentiometer for Compressor #3
and #4 at the time of the fault.
System Data

System #1 Pressures

VSD

INTERNAL AMBIENT TEMP = XXX.X F

COOLING SYSTEM STATUS = YYY

SYS 1 PRESSURES
SUCTION = XXXX

OIL = XXXX PSIG

DISCHARGE = XXXX PSIG

This message displays the VSD/Microprocessor internal ambient cabinet temperature and the cooling system status (on or off) at the time of the fault.

This message displays all of the measured system pressures (oil, suction, and discharge) at the time of the
fault.

IGBT Baseplate Temperature

System # 1 Measured Temperatures

VSD IGBT BASEPLATE TEMPS T1 = XXX F


T2 = XXX F

This message displays the IGBT highest baseplate temperature for 2 and 3 compressor units at the time of the
fault. 4 compressor units display temperatures for1/3
(T1) and 2/4 (T2).
Precharge Signal Status and VSD Cooling
Status
VSD

PRECHARGE SIGNAL = XXX

VSD

PRECHARGE 1 SIGNAL = XXX

PRECHARGE 2 SIGNAL = XXX

This display provides the state of the precharge signal, where Precharge 1 and Precharge 2 is either ON or
OFF at the time of the fault. Precharge 2 is only used
on 4 compressor units.

JOHNSON CONTROLS

SYS 1 TEMPERATURES
SUCTION = XXX.X

OIL = XXX.X F

DISCHARGE = XXX.X F

This message displays all of the measured system temperatures (oil, suction, and discharge) at the time of the
fault.
System #1 Measured Suction Temperature
and Calculated SAT Suction Temperature and
Superheat
SYS 1 SUCTION
SUPERHEAT = XXX.X

TEMP = XXX.X F
SAT REMP = XXX.X F

This message displays all of the calculated suction


temperatures (saturated suction and system superheat)
at the time of the fault as well as measured suction temperature.

265

MICROPANEL
FORM 201.23-NM1 (910)

System #1 Calculated Discharge


Temperatures
SYS 1 DISCHARGE
SUPERHEAT = XXX.X

TEMP = XXX.X F
SAT REMP = XXX.X F

This message displays all of the calculated discharge


temperatures (saturated discharge and discharge superheat) at the time of the fault as well as measured discharge temperature.
System #1 Motor Temperatures
SYS 1 MOTOR TEMPS

T1 = XXX.X F

T3 = XXX.X F

T2 = XXX.X

This message displays the System 1 motor thermistor


temperatures at the time of the fault.
System #1 Compressor Speed and Economizer
Solenoid Status
SYS 1 COMPRESSOR

SPEED = XXX.X %

ECONOMIZER SOLENOID = XXX

This message indicates the compressor speed and status of economizer solenoid at the time of the fault. The
economizer status will be indicated as either ON or
OFF.
System #1 Flash Tank Level and Feed Valve
% Open
SYS 1 FLASH TANK

LEVEL = XXX.X %

FEED VALVE PERCENT OPEN = XXX.X %

This message displays the liquid level in the flash tank


and indicates the % the Flash Tank Feed Valve is open
at the time of the fault.
System #1 Suction Superheat and Flash Tank
Drain Valve % Open
SYS 1

SUCTION SUPERHEAT = XXX.X F

DRAIN VALVE PERCENT OPEN = XXX.X %

This message displays the system suction superheat


and indicates the % the Flash Tank Drain Valve is open
at the time of the fault.

266

System #1 Fan Stage and Compressor Heater


Status
SYS 1 CONDENSER FANS ON = XXX

COMPRESSOR HEATER = XXX

This message displays the actual # of system fans on,


and the status of the compressor heater at the time of
the fault. The fan display will show the number of fans
operating while the compressor heater status will indicate either ON or OFF.
Compressor #1 Run Time
SYS 1 RUN TIME
XX DAYS XX HOURS XX MINUTES XX SECONDS

This message displays the system run time since the


last start in days, hours, minutes, and seconds at the
time of the fault.
System #1 Run Signals
SYS 1 RUN SIGNALS
RUN PERM = XXX

RELAY = XXX
SOFTWARE = XXX

This message displays the System Run Signal Relay


(Relay Output Board) status, Run Permissive Input
status, and the Internal Software (microprocessor command) ON/OFF Start status. The status of each will
indicate either ON or OFF.
System 2 through 4 Data
Data for the remaining systems 2 through 4 at the time
of the fault is displayed in the same sequence as the
system #1 data.
Compressor Operating Hours and Starts
HOURS 1=XXXXX, 2=XXXXX, 3=XXXXX, 4=XXXXX
START 1=XXXXX, 2=XXXXX, 3=XXXXX, 4=XXXXX

This message displays compressor operating hours and


compressor starts at the time of the fault. On 3 and 4
compressor units, the data and compressor designators
for compressors not present will be blanked out.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Chilled Liquid Setpoint Cooling Setpoints

SETPOINTS
LOCAL COOLING SETPOINT

= XXX.X F

This message displays the programmed cooling setpoint


at the time of the fault.
SETPOINTS
LOCAL CONTROL RANGE

= +/- X.X F

This message displays the programmed Control Range


at the time of the fault.
Remote Setpoint and Range
SETPOINTS REMOTE SETPOINT = XXX.X F

OPTIONS

REMOTE CONTROL RANGE = +/- X.X F

This message displays the remote setpoint and Control


Range at the time of the fault.

LOCAL / REMOTE CONTROL MODE


XXXXXXXXXXXXXXXXXXXXX

When Remote Control Mode is selected, control of the


Chilled Liquid Setpoint is from a remote device such
as an ISN/BAS controller.
OPTIONS

DISPLAY UNITS
XXXXXXXXXXXXXXXXXXXX

Display Units Mode


This message indicates whether SI (C, Barg) or Imperial units (F, PSIG) was selected at the time of the
fault.
OPTIONS

LEAD / LAG CONTROL MODE


XXXXXXXXXXXXXXXXXXXXX

System Lead/Lag Control Mode

Options

This message indicates the type of lead lag control selected at the time of the fault. Five choices are available:
Automatic
Sys 1 Lead
Sys 2 Lead
Sys 3 Lead
Sys 4 Lead.

Display Language

The default mode will be AUTOMATIC.

Maximum Remote Temperature Setpoint


SETPOINTS
MAXIMUM REMOTE TEMP RESET = XXX.X F

This message displays the maximum remote reset programmed at the time of the fault.

OPTIONS

DISPLAY LANGUAGE
XXXXXXXXXXXXXXXXXXXX

This message displays the language selected at the time


of the fault.
Chilled Liquid Cooling Mode

Remote Temperature Reset


One of the 5 messages below indicates whether remote
temperature reset was active or disabled at the chiller
keypad at the time of the fault. If active, the type of
reset signal selected is indicated. If the option is not
factory enabled, the option will not appear.
OPTIONS

REMOTE TEMP RESET INPUT

DISABLED

This message displays the chilled liquid temperature


mode (water or glycol) selected at the time of the
fault.

OPTIONS

REMOTE TEMP RESET INPUT

0.0 TO 10.0 VOLTS DC

OPTIONS

REMOTE TEMP RESET INPUT

Local / Remote Control Mode

2.0 TO 10.0 VOLTS DC

OPTIONS

REMOTE TEMP RESET INPUT

0.0 TO 20.0 MILLIAMPS

OPTIONS

REMOTE TEMP RESET INPUT

4.0 TO 20.0 MILLIAMPS

OPTIONS

CHILLED LIQUID COOLING MODE

WATER COOLING

OPTIONS

CHILLED LIQUID COOLING MODE

GLYCOL COOLING

This message indicates whether Local or Remote Control Mode was selected at the time of the fault.

JOHNSON CONTROLS

267

MICROPANEL
FORM 201.23-NM1 (910)

Low Ambient Temp Cutout

Low Leaving Chilled Liquid Temp Cutout

OPTIONS

LOW AMBIENT TEMP CUTOUT

PROGRAM

XXXXXXXXXXXXXXXXXXXX

LEAVING LIQUID TEMP CUTOUT = XXX.X F

This message indicates whether the low ambient cutout


was enabled or disabled at the time of the fault.
Remote Current Reset
OPTIONS

REMOTE CURRENT LIMIT INPUT

DISABLED

OPTIONS

REMOTE CURRENT LIMIT INPUT

0.0 TO 10.0 VOLTS DC

OPTIONS

REMOTE CURRENT LIMIT INPUT

2.0 TO 10.0 VOLTS DC

OPTIONS

REMOTE CURRENT LIMIT INPUT

0.0 TO 20.0 MILLIAMPS

OPTIONS

REMOTE CURRENT LIMIT INPUT

4.0 TO 20.0 MILLIAMPS

This message indicates whether remote current reset


was active or disabled at the chiller keypad at the time
of the fault and if active, the type of reset signal selected. One of the following messages will be indicated:
DISABLED (no signal)
0 to 10VDC
2 to 10VDC
0 to 20ma
4 to 20ma.
If the option is not factory enabled, the option will not
appear.
Program Values
Suction Pressure Cutout
PROGRAM
SUCTION PRESSURE CUTOUT = XXX.X PSIG

This message indicates the he suction pressure cutout


programmed at the time of the fault.
Low Ambient Cutout
PROGRAM
LOW AMBIENT TEMP CUTOUT = XXX.X F

This message displays the low ambient temp cutout


programmed at the time of the fault.

268

This message displays the low leaving Chilled liquid


temperature cutout programmed at the time of the
fault.
Motor Current Limit
PROGRAM
MOTOR CURRENT LIMIT

= XXX %FLA

This message indicates the motor current limit programmed at the time of the fault.
Pulldown Current Limit
PROGRAM
PULLDOWN CURRENT LIMIT

= XXX %FLA

This message indicates the pulldown current limit programmed at the time of the fault.
Pulldown Current Limit Time
PROGRAM
PULLDOWN CURRENT LIMIT TIME

= XXX MIN

This message indicates the pulldown current limit time


programmed at the time of the fault.
Suction Superheat Setpoint
PROGRAM
SUCTION SUPERHEAT SETPOINT

= XXX.X F

This message indicates the suction superheat setpoint


programmed at the time of the fault.
Unit ID Number
PROGRAM
REMOTE UNIT ID NUMBER

=X

This indicates the unit ID # programmed at the time of


the fault.
Sound Limit Setpoint
PROGRAM
SOUND LIMIT SETPOINT

= XXX %

This indicates the sound limit setpoint programmed at


the time of the fault, if the sound limit option is activated at the factory. If the option is not factory activated,
the display will not appear.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

setpoints key
SETPOINTS
key

8
LD10605

Setpoints Key Operation


Cooling setpoints and ranges may be programmed by
pressing the SETPOINTS key. The first setpoint entry screen will be displayed as shown below. The first
line of the display will show the chiller default (DEF),
minimum acceptable value (LO) and maximum acceptable value (HI). The second line shows the actual programmed value. TABLE 16 also shows the allowable
ranges for the cooling setpoints and Control Ranges.
Note that the Imperial units are exact values while the
Metric units are only approximate.
SETPOINTS

DEF XXXXX LO XXXXX HI XXXXX

LOCAL COOLING SETPOINT

= XXX.X F

Pressing the SETPOINTS key a second time or the


(Arrow) key will display the leaving chilled liquid
Control Range, default, and low/high limits.
SETPOINTS

DEF XXXXX LO XXXXX HI XXXXX

LOCAL CONTROL RANGE

JOHNSON CONTROLS

Pressing the SETPOINTS key or the (Arrow) key


a third time will display the remote setpoint and cooling range. This display automatically updates about
every 2 seconds. This remote setpoint message is show
below:
SETPOINTS REMOTE SETPOINT = XXX.X F

REMOTE CONTROL RANGE = +/- X.X F

If there is no remote setpoint being utilized, the remote


setpoint value will be displayed as XXXXXX and the
remote Control Range will display XXX.
Pressing the SETPOINTS key or the Arrow key a fourth
time will bring up a screen that allows the Maximum
Remote Temperature Reset to be programmed. This
message is show below:
SETPOINTS DEF XXXXX LO XXXXX HI XXXXX
MAXIMUM REMOTE TEMP RESET

= XXX.X F

= +/- X.X F

269

MICROPANEL
FORM 201.23-NM1 (910)

The values displayed under each of the key presses may


be changed by keying in new values and pressing the
(ENTER) key to store the new value into memory.
Where more than one value may be keyed in on a display, a portion of the data that does not need updating
may be skipped by pressing the (ENTER) key. The
(ENTER) key must also be pressed after the last
value in the display to store the data into memory.

The (ARROW) key allows scrolling back through


the setpoints displays.
The minimum, maximum, and default values allowed
under the SETPOINTS key are provided in TABLE
16.

TABLE 16 - setpoint limits


Program Value

Mode
Water Cooling

Leaving Chilled Liquid Setpoint


Glycol Cooling

270

Leaving Chilled Liquid Control Range

Max. Remote Temperature Reset

Low Limit

High Limit

Default

40.0F

60.0F

44.0F

4.4C

15.6C

6.7C

15.0F

70.0F

44.0F

-9.4C

15.6C

6.7C

1.5F

2.5F

2.0F

0.8C

1.4C

1.1C

2F

40F

20F

1C

22C

11C

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Program key

program
key

8
LD10605

Program Key Operation


Various operating parameters are programmable by the
user. These are modified by pressing the PROGRAM
key and then the (ENTER) key to enter Program
Mode. A listing of the limits of the programmable values is found below. Note that the Imperial units are
exact values, while Metric units are only approximate.
The and (Arrow) keys are used to scroll
through the user programmable values. A value may
be changed by keying in the new value and pressing
the (ENTER) key to store the new value in memory. The cursor will be displayed on the screen when a
number key is pressed. The first line of each message
will indicate the chiller default (DEF) value), lowest
acceptable programmable value (LO), and highest acceptable programmable value (HI). The user programmable value is programmed on in the second line of
the message.
When the PROGRAM key is first pressed, the following display will appear indicating the user is in the program mode:

Pressing the (ENTER) key again will display the


first programmable selection.
Suction Pressure Cutout
PROGRAM

DEF XXXXX LO XXXXX HI XXXXX

SUCTION PRESSURE CUTOUT

= XXX.X PSIG

The suction pressure cutout is protects the chiller from


a low refrigerant condition. It also helps protect from
a freeze-up due to low or no chilled liquid flow. However, it is only a back-up for a flow switch and cannot
protect against an evaporator freeze under many conditions. This cutout is programmable and should generally be programmed for 24PSIG (1.65 Barg) for chilled
water cooling.
The cutout is programmable between 24.0 and 36.0
PSIG (1.65 and 2.48 Barg) in the Water Cooling mode
and 5.0 and 36.0 (0.34 and 2.28 Barg) in the Glycol
Cooling mode. The default value for both modes will
be 24.0 PSIG (1.65 Barg) PSIG.

PROGRAM MODE XXXX


PRESS ENTER KEY TO CONTINUE

JOHNSON CONTROLS

271

MICROPANEL
FORM 201.23-NM1 (910)

Low Ambient Cutout


PROGRAM

Pulldown Current Limit Time

DEF XXXXX LO XXXXX HI XXXXX

LOW AMBIENT TEMP CUTOUT

= XXX.X F

The low ambient temp cutout allows programming the


outdoor temperature at which it is desired to shut down
the chiller to utilize other methods of cooling.
The cutout is programmable between 2.0F (-18.9C)
and 50F (10.0 C) with a 25F (-3.9C) default.
Low Leaving Liquid Temp Cutout
PROGRAM

DEF XXXXX LO XXXXX HI XXXXX

LEAVING LIQUID TEMP CUTOUT = XXX.X F

The leaving chilled liquid temp cutout is programmed


to avoid freezing the evaporator due to excessively low
chilled liquid temperatures. The cutout is automatically set at 36F (2.2 C) in the Water Cooling mode
and is programmable in the Glycol Cooling mode. In
the Glycol Cooling Mode, the cutout is programmable
from 11.0F to 36.0F (-11.7 to 2.2C) with a default
of 36.0F (2.2C).
Motor Current Limit
PROGRAM

DEF XXXXX LO XXXXX HI XXXXX

MOTOR CURRENT LIMIT

= XXX % FLA

The motor current limit %FLA is programmable. This


allows the microprocessor to limit a system before it
faults on high current. Typically, the limit point is set
at 100%. The unload point is programmable from 30
to 100% with a default of 100%.

PROGRAM

DEF XXXXX LO XXXXX HI XXXXX

PULLDOWN CURRENT limit TIME

= XXX min

The pulldown current limit time is programmable.


This allows the microprocessor to limit a system on
pulldown limiting for a defined period of time for the
purpose of peak time energy savings. The pulldown
limit point is programmable from 0 to 255 with a default of 0 Min.
Suction Superheat Setpoint
PROGRAM

DEF XXXXX LO XXXXX HI XXXXX

SUCTION SUPERHEAT SETPOINT = XXX.X F

The suction superheat setpoint is programmable from


8.0 to 12.0F (4.4 to 8.3C) with a 10.0F (5.6C)
default. Typically the superheat control will be programmed for 10.0 F. Higher superheats between 10
and 12F will reduce the risk of liquid carry over and
are preferred by some users.
Unit ID Number
PROGRAM

DEF XXXXX LO XXXXX HI XXXXX

REMOTE UNIT ID NUMBER = X

For purposes of remote communications, multiple


chillers may be connected to an RS-485 communications bus. To allow communications to each chiller, a
chiller ID number may be programmed into memory.
On a single chiller application, the value will be 0.

Pulldown Current Limit


PROGRAM

DEF XXXXX LO XXXXX HI XXXXX

pulldown CURRENT LIMIT

= XXX % FLA

The pulldown current limit %FLA is programmable.


This allows the microprocessor to limit a system on
pulldown limiting for the purpose of peak time energy savings. Typically, the limit point is set at 100%.
The pulldown limit point is programmable from 30 to
100% with a default of 100%. Be aware when using
pulldown motor current limit, the chiller may not be
able to load to satisfy temperature demand

272

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Sound Limit Setpoint


PROGRAM

Default Values

DEF XXXXX LO XXXXX HI XXXXX

SOUND LIMIT SETPOINT

= XXX %

The sound limit setpoint is programmable from 0 to


100 % with a 0% default. 0% allows operating up to
the full speed capability of the unit with no sound limiting. Typically the sound limit control setting will be
programmed for 0 % unless sound limiting is utilized
on the chiller. Sound limiting will only permit the unit
to run to a frequency less than the maximum speed
capability of the unit. Programming a value of 1%
would be the minimum sound limiting that can be programmed and 100% will be the maximum. 100% will
only allow the unit speed to operate at the minimum
frequency. Usually, the sound limit % will be programmed somewhere between 0 and 100% according
the limiting needed to satisfy the sound requirements
of the site. Typically, sound limiting will be utilized in
areas sensitive to noise during night-time hours. The
sound limit display will only be present if the sound
limit option is programmed at the factory.

A listing of the low limits, high limits, and default values for each of the programmable values is noted in
each display and can be found in TABLE 17. Note that
the Imperial units are exact values while the Metric
units are only approximate.

TABLE 17 - programmable operating parameters


Program Value

Suction Pressure Cutout

Low Ambient Temp. Cutout

Leaving Chilled Liquid Temp. Cutout

Mode

Low Limit

High Limit

Default

Water
Cooling

24.0 PSIG

36.0 PSIG

24.0 PSIG

1.65 Bars

2.48 Bars

1.65 Bars

Glycol
Cooling
Water
Cooling

5.0 PSIG

36.0 PSIG

24.0 PSIG

0.34 Bars

2.48 Bars

1.65 Bars

-2F

50.0F

25.0F

-18.9C

10.0C

2.2C

36.0F

2.2C

Glycol
Cooling

11.0F

36.0F

36.0F

-11.7C

2.2C

2.2C

Motor Current Limit

30%

103%

103%

Pulldown Motor Current Limit

30%

100%

100%

Pulldown Motor Current Limit Time

0 Min

255 Min

0 Min

Suction Superheat Setpoint

Unit ID Number

Sound Limit Setpoint

JOHNSON CONTROLS

Sound Limit
Option Enabled

8.0F

12.0F

10.0F

4.4C

6.6C

5.6C

0%

100%

0%

273

MICROPANEL
FORM 201.23-NM1 (910)

options key

options
KEy

LD10605

Options Key Operation

Chilled Liquid Cooling Mode Selection

The OPTIONS key provides the user with a display of


unit configuration and the capability to modify the configuration. These options can only be viewed under the
OPTIONS key. To view the current options settings,
press the OPTIONS key. Each press of the OPTIONS
key or press of the or (Arrow) keys will scroll
to the next option setting. The and (Arrow)
keys allow changing the option choices. The (ENTER) key must be pressed after a selection is made to
save the change in memory.

The Chilled liquid cooling mode can be selected for


Water Cooling or low temperature Glycol Cooling.

An explanation of each option message is provided below.

When Glycol Cooling is chosen, the chilled liquid


temperature setpoint can be programmed from 10F to
70F.

Display Language Selection


The display language can be selected for English,
Dutch, German, Italian, and Chinese
OPTIONS

DISPLAY LANGUAGE

XXXXXXXXXXXXXXXXXX

OPTIONS

CHILLED LIQUID COOLING MODE

XXXXXXXXXXXXXXXXXX

When Water Cooling is chosen, the chilled liquid temperature setpoint can only be programmed from 40F
to 70F
OPTIONS

CHILLED LIQUID COOLING MODE

WATER COOLING

OPTIONS

CHILLED LIQUID COOLING MODE

GLYCOL COOLING

The default Chilled Liquid Mode will be WATER.

The default language will be English.

274

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Local / Remote Control Mode Selection

System Lead/Lag Control Mode Selection

Local or Remote Control Mode allows the user to select the chilled liquid temperature control mode.

The operator may select the type of lead/lag control


desired.

OPTIONS

local / remote control MODE

OPTIONS lead / Lag control MODE

XXXXXXXXXXXXXXXXXX

When LOCAL CONTROL mode is selected, chilled


liquid control is from the keypad of the chiller. In local
mode, a remote device can read system data, but not
reset operating parameters.
OPTIONS

local / remote control MODE

local control

When REMOTE CONTROL mode is selected, control


of the chilled liquid setpoint is from a remote device
such as an ISN/BAS controller.
OPTIONS

local / remote control MODE

remote control

The default mode will be LOCAL.

XXXXXXXXXXXXXXXXXX

In most cases, automatic lead/lag will be selected.


When automatic lead/lag is selected, the microprocessor will attempt to balance run time by switching the
lead compressor whenever all compressors are shut
off. If a compressor is not able to run when the microprocessor attempts a start, the microprocessor will
select another compressor in an effort to control chilled
liquid temperature. Manual lead/lag allows selecting a
specific compressor to be the lead. If #2 is selected as
the lead in a 3 compressor chiller, the sequence will be
2, 3, and 1.
OPTIONS lead / Lag control MODE

automatic

Display Units Selection

The default mode will be AUTOMATIC.

Imperial or SI display units may be selected for data


display.

Lag selections of individual systems will appear as:

OPTIONS display units


XXXXXXXXXXXXXXXXXX

The user may select system operating temperatures and


pressures to be displayed in either SI (C, Barg) or Imperial units (F, PSIG).
OPTIONS display units
imperial
OPTIONS display units

SI

The default mode is IMPERIAL.

JOHNSON CONTROLS

OPTIONS lead / Lag control MODE


manual sys 1 lead
OPTIONS lead / Lag control MODE
manual sys 2 lead
OPTIONS lead / Lag control MODE
manual sys 3 lead

SYSTEM 3 LEAD may be selected only on 3 and 4


compressor units.
OPTIONS lead / Lag control MODE
manual sys 4 lead

SYSTEM 4 LEAD may be selected only on 4 compressor units.

275

MICROPANEL
FORM 201.23-NM1 (910)

Remote Temperature Reset Selection


Remote temperature reset from an external source may
be tied directly into the chiller microprocessor board.
OPTIONS remote temp reset input

XXXXXXXXXXXXXXXXXX

Selections may be made for DISABLED (no signal), 0


to10VDC, 2 to 10VDC, 0 to 20ma, and 4 to 20ma.
OPTIONS remote temp reset input
disabled
OPTIONS remote temp reset input

0.0 to 10.0 volts dc

OPTIONS remote temp reset input


2.0 to 10.0 volts dc

OPTIONS remote temp reset input


0.0 to 20.0 milliamps

OPTIONS remote temp reset input


4.0 to 20.0 milliamps

The default setting for Remote Temp Reset is DISABLED. This display will only appear if the remote
temp limit option is enabled at the factory.
Remote Current Limit Input Selection
Remote current limit from an external source may be
tied directly into the chiller microprocessor board.
OPTIONS remote Current limit input
xxxxxxxxxxxxxxxxxxxxx

Selections may be made for DISABLED (no signal), 0


to 10VDC, 2 to 10VDC, 0 to 20ma, and 4 to 20ma.
OPTIONS remote Current limit input
disabled
OPTIONS remote Current limit input

0.0 to 10.0 volts dc

OPTIONS remote Current limit input


2.0 to 10 volts dc

The default setting for Remote Current Reset is DISABLED. This display will only appear if the remote
current limit option is enabled at the factory.
Remote Sound Limit Selection
Remote sound limit from an external source may be
tied directly into the chiller microprocessor board.
OPTIONS remote sound limit input
xxxxxxxxxxxxxxxxxxxx

Selections may be made for DISABLED (no signal), 0


to10VDC, 2 to 10VDC, 0 to 20ma, and 4 to 20ma.
OPTIONS remote sound limit input
disabled
OPTIONS remote sound limit input

0.0 to 10.0 volts dc

OPTIONS remote sound limit input


2.0 to 10.0 volts dc

OPTIONS remote sound limit input


0.0 to 20.0 milliamps

OPTIONS remote sound limit input


4.0 to 20.0 milliamps

The default setting for Remote Sound Limit is DISABLED. This display will only appear if the remote
sound limit option is enabled at the factory.
Low Ambient Cutout Enable/Disable
The low ambient cutout may be enabled or disabled.
When enabled, the chiller will cut off when the low
ambient cutout is reached. When disabled, the chiller
will run at any temperature.
OPTIONS

low ambient temperature cutout

enabled

OPTIONS

low ambient temperature cutout

disabled

The default setting for the low ambient cutout will be


ENABLED.

OPTIONS remote Current limit input


0.0 to 20.0 milliamps

OPTIONS remote Current limit input


276

4.0 to 20.0 milliamps

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

date/time and schedule keys

date/time
KEy

schedule
KEy

8
LD10605

Date/Time Key Operation

CLOCK FRI 18-JUN-2005 10:15:33 AM

When the DATE/TIME key is pressed, the chiller microprocessor will display the date and the time. This
feature is useful and required for using the Daily
Schedule. It is also a valuable tool for troubleshooting
to allow a technician to determine the time of the fault,
which is stored in the history memory buffers. When
the DATE/TIME key is pressed, the first display screen
shown below will be displayed:

DAY OF month

CLOCK FRI 18-JUN-2005 10:15:33 AM


DAY OF WEEK

= XXX

Whenever any changes are made, the (ENTER) key


must be pressed to store the data.
Pressing the or (Arrow) keys allows scrolling
to the next programmed item. Pressing the (DOWN
ARROW) key scrolls to the next item that can be programmed and the (UP ARROW) key scrolls to the
previous item.
The day of the week is the first display and can be
changed by pressing either the or (LEFT OR
RIGHT ARROW) key to select the day. After the day
is selected, the (ENTER) key must be pressed to
store the data.
JOHNSON CONTROLS

= XX

Pressing the (DOWN ARROW) key again scrolls to


the day of the month:
CLOCK FRI 18-JUN-2005 10:15:33 AM
DAY OF month

= XX

The day of the month can be selected by keying in the


numerical value to select the day. After the day of the
month is selected, the (ENTER) key must be pressed
to store the data.

A 0 must be typed in to select dates


for days of the 1st through the 9th.

Pressing the (DOWN ARROW) key again scrolls


to month:
CLOCK FRI 18-JUN-2005 10:15:33 AM
month

= XX

277

MICROPANEL
FORM 201.23-NM1 (910)

The month can be selected by keying in the numerical


value to select the day. After the month is selected, the
(ENTER) key must be pressed to store the data.

A 0 must be keyed in for months 01


through 09. The panel will automatically provide the abbreviation of the
month.
Pressing the (DOWN ARROW) key again scrolls
to the year:
CLOCK FRI 18-JUN-2005 10:15:33 AM
year

= XXxX

The year can be selected by keying in the numerical


value to select the year. After the year is selected, the
(ENTER) key must be pressed to store the data.
Pressing the (DOWN ARROW) key again scrolls
to the hour:
CLOCK FRI 18-JUN-2005 10:15:33 AM
hour

= XX

The hour can be selected by keying in the numerical


value for the hour. After the hour is selected, the
(ENTER) key must be pressed to store the data.

One or two 0s must be keyed in for


hours 00-09.

Pressing the (DOWN ARROW) key again scrolls


to the minute:
CLOCK FRI 18-JUN-2004 10:15:33 AM
MINUTE

= XX

The minute can be selected by keying in the numerical


value for the hour. After the minute is selected, the
(ENTER) key must be pressed to store the data.

Pressing the (DOWN ARROW) key again scrolls


to AM/PM:
CLOCK FRI 18-JUN-2004 10:15:33 AM
AM/PM

= XX

AM/PM can be selected by pressing the or


(arrow) keys. After the meridian is selected, the
(ENTER) key must be pressed to store the data.
Pressing the (DOWN ARROW) key again scrolls to
the time format selection:
CLOCK FRI 18-JUN-2004 10:15:33 AM
TIME FORMAT

= XXXXXXX

The time format may be displayed in either a 12 hour


or 24 hour format. Selection can be changed by pressing the or (arrow) keys. The (ENTER) key
must be pressed to store the data.
Schedule Key Operation
The Daily Schedule must be programmed for the unit
start and stop times. To set the schedule, press the
SCHEDULE key. The display will provide a message
allowing access to 2 types of schedule information:
SCHEDULE

CHOOSE SCHEDULE TYPE

XXXXXXXXXXXXXXXXXXXXXXXXX

The schedule types are:


UNIT OPERATING SCHEDULE
(Default selection)
SOUND LIMIT SCHEDULE
(Only if Sound Limiting is enabled by the factory
when the option is installed.)
The schedule type (UNIT OPERATING SCHEDULE
or SOUND LIMIT SCHEDULE) may be changed by
pressing the (LEFT ARROW) or (RIGHT ARROW) keys followed by the (ENTER) key. The selection must be entered by pressing the (ENTER)
key before a schedule display will appear.

One or two 0s must be keyed in for


minutes 00 through 09.

278

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Unit Operating Schedule


The Unit Operating Schedule is used to enable/disable the chiller unit on time of day. The chiller can be
enabled and disabled once each day or it can be programmed to run continuously. Any time the daily or
holiday schedule shuts the chiller down, the running
system(s) will go through a controlled ramped shutdown. If the UNIT OPERATING SCHEDULE is selected under the CHOOSE SCHEDULE display, the
following message will appear:
SCHEDULE

UNIT OPERATING

MON START = 06:00 AM STOP = 10:00 PM

The line under the 0 is the cursor. If the start time is


wrong, it can be changed by keying in the new time
from the numeric keypad. Once the correct values for
the START hour and minute are entered, press the
(ENTER) key. The cursor will then move to the AM/
PM selection. The meridian (AM/PM) value may be
changed by the (LEFT ARROW) or (RIGHT
ARROW) keys and entered by pressing (ENTER)
key. Repeat this process for the STOP time. Once a
schedule is entered, the schedule for the next day will
appear. The start and stop time of each day may be
programmed differently. To view the schedule without
making a change, simply press the SCHEDULE key
until the day you wish to view appears. The (UP
ARROW) key will scroll backwards to the previous
screen.

If at any time the schedule is changed


for Monday, all the other days will
change to the new Monday schedule.
This means if the Monday times are
not applicable for the whole week,
then the exceptional days would need
to be reprogrammed to the desired
schedule.

JOHNSON CONTROLS

To program the chiller for 24 hour operation, program


the start and stop times of each day of the week for
00:00.
After the SUN (Sunday) schedule appears on the display, a subsequent press of the SCHEDULE or (UP
ARROW) key will display the Holiday schedule. This
is a two-part display. The first reads:
SCHEDULE

UNIT OPERATING

HOL START = 00:00 AM STOP = 00:00 PM

The holiday times may be set using the same procedure


as described above for the days of the week. Be sure to
press the (ENTER) key after setting the START and
STOP times to save the change in memory. Pressing
the SCHEDULE key a second time, the display will
show the individual days:
SCHEDULE

UNIT OPERATING

S M T W T F S HOLIDAY NOTED BY *

The line below the empty space is the cursor and will
move to the next or previous empty space when the
(LEFT ARROW) or (RIGHT ARROW) keys and
pressed. To set a day for the Holiday Schedule, the
cursor must be moved to the space following the day
of the week. The * key is then pressed and an * will
appear in the space signifying that day as a holiday.
The Holiday schedule must be programmed weekly. If
there is no holiday, the * key is also used to delete the
*. The (ENTER) key is used to accept the holiday
schedule for the entire week.

The HOLIDAY SCHEDULE is a temporary schedule. Once the schedule


is executed, the selected holidays will
be cleared from memory for the following week.

279

MICROPANEL
FORM 201.23-NM1 (910)

Sound Limit Schedule


The SOUND LIMIT SCHEDULE allows setting the
day and time when the user desires using the SILENT
NIGHT factory programmed option to limit chiller
loading and fan operation for reduced audible noise in
the surrounding area. If the SOUND LIMIT SCHEDULE is selected under the CHOOSE SCHEDULE display, the following message will appear:
SCHEDULE

SOUND LIMIT

MON START = 06:00 AM

= XXX %

STOP = 10:00 PM

The Sound Limit option can be enabled and disabled


once each day or the chiller can be set to run continuously in this mode for sound limiting whenever the
chiller is operating. When sound limiting is enabled,
the unit will be limited by the Sound Limit setpoint
% as set under the PROGRAM key. XXX in the display above will show the Sound Limit Setpoint % programmed under the PROGRAM key. 0% will cause
no speed reduction, while 100% only allows running at
minimum speed.

The AM/PM selection may be chosen using the


(LEFT ARROW) or (RIGHT ARROW) keys and
pressing (ENTER) key to store the value.
This process is repeated for the STOP time.
Once the schedule for a specific day is programmed
and entered, the schedule for the next day will appear.
The schedule for each day may be programmed the
same or differently.
To view the schedule without changing it, simply press
the SCHEDULE key or the (DOWN ARROW) key
until the desired day is displayed. The (UP ARROW)
key will scroll backwards to the previous screen.

If the schedule is changed for Monday, all other days will change to the
Monday schedule. Be aware of this
when programming.

The START Time for a specific day (hour and minute)


is entered using the same guidelines used for the start/
stop schedules, and press the (ENTER) key to store
it into memory. The cursor will then move to the AM/
PM selection.

280

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

manual override key

manual override
KEy

8
LD10605

Manual Overrride Key Operation


If the MANUAL OVERRIDE key is pressed during
a schedule shutdown, the STATUS display will display the message below. This indicates that the Daily
Schedule is being ignored and the chiller will start
when chilled liquid temperature allows, Remote Contacts, UNIT switch and SYSTEM switches permitting.
This is a priority message and cannot be overridden by
anti-recycle messages, fault messages, etc. when in the
STATUS display mode. Therefore, do not expect to see
any other STATUS messages when in the MANUAL
OVERRIDE mode. MANUAL OVERRIDE is to only
be used in emergencies or for servicing. Manual override mode automatically disables itself after 30 minutes.
manual override

JOHNSON CONTROLS

281

MICROPANEL
FORM 201.23-NM1 (910)

print key

print
KEy

LD10605

Print Key Operation


The PRINT key is used to initiate a printout of current operating data (real time data), a complete history
printout of all history (fault) buffers, a printout of all
normal shutdowns (compressor cycling, chiller shutdown, etc.) or history (fault) data printout of a specific
fault. History Buffer 1 will always be the most recent
fault history printout. Printing may also be canceled
by selecting the CANCEL PRINTING option. The following message is displayed when the PRINT key is
pressed.
PRINT CHOOSE PRINT REPORT

XXXXXXXXXXXXXXXXXXXXX

After pressing the PRINT key, the printout type is


selected by pressing the (LEFT ARROW) or
(RIGHT ARROW) keys until the desired printout is
displayed.
TABLE 18 shows the available printout types.

282

TABLE 18 - printout types


PRINTOUT TYPES
Operating Data
(Default Selection)
All History Buffers
Normal Shutdowns
History Buffer 1
History Buffer 2
History Buffer 3
History Buffer 4
History Buffer 5
History Buffer 6
History Buffer 7
History Buffer 8
History Buffer 9
History Buffer 10
Cancel Printing

The specific printout is initiated by pressing the


(ENTER) key.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

A sample of the operating data printout is shown below. The operating data printout is a snapshot of current system operating conditions when the printout was
selected. The sample shows combined printouts of 2,
3, and 4 circuit units. The actual printout will only
show data for the appropriate chiller type.

Bold italic text below a line of print is


not on the actual printout. Bold italic
text indicates information that may
not be available on all printouts or is
additional information to help explain
the difference in a 2/3 or 4-circuit
printout.
Operating Data Printout
YORK INTERNATIONAL CORPORATION
LATITUDE SCREW CHILLER
OPERATING DATA
2:04:14 PM 18 FEB 10
SYS 1
NOT RUNNING
SYS 2
COMPRESSOR RUNNING
OPTIONS
CHILLED LIQUID
WATER
LOCAL/REMOTE MODE
REMOTE
LEAD/LAG CONTROL
AUTOMATIC
REMOTE TEMP RESET
DISABLED
REMOTE CURRENT LIMIT
0 TO 10 V
REMOTE SOUND LIMIT
4 TO 20 MA
(if Sound Limiting enabled)
LOW AMBIENT CUTOUT
ENABLED
PROGRAM VALUES
SUCT PRESS CUTOUT
44 PSIG
LOW AMBIENT CUTOUT
25.0 DEGF
LEAVING LIQUID CUTOUT
36.0 DEGF
MOTOR CURRENT LIMIT
100 %FLA
PULLDOWN CURRENT LIMIT
100 %FLA
PULLDOWN LIMIT TIME
0 MIN
SUCTION SUPERHEAT SETP
12.0 DEGF
UNIT ID NUMBER
0
SOUND LIMIT SETPOINT
100%
(if Sound Limiting enabled)
UNIT DATA
LEAVING LIQUID TEMP
49.0 DEGF
RETURN LIQUID TEMP
58.2 DEGF
TEMP RATE
XXX.X DEGF/MIN
COOLING RANGE
42.0+/-2.0 DEGF
REMOTE SETPOINT
44.0 DEGF
AMBIENT AIR TEMP
74.8 DEGF
LEAD SYSTEM
SYS 2
FLOW SWITCH
ON
EVAPORATOR PUMP RUN
ON
EVAPORATOR HEATER
OFF
ACTIVE REMOTE CONTROL
NONE
OPERATING HOURS 1=XXXXX, 2=XXXXX
3=XXXXX
(3 circuit)
JOHNSON CONTROLS


3=XXXXX, 4=XXXXX
START COUNTER
1=XXXXX, 2=XXXXX

3=XXXXX
(3 circuit)

3=XXXXX, 4=XXXXX
(4 circuit)
SOFTWARE VERSION
C.ACS.XX.00
VSD DATA
ACTUAL FREQUENCY
XXX.X HZ
COMMAND FREQUENCY
XXX.X HZ
DC BUS VOLTAGE
XXX VDC
(2 circuit & 3 circuit)
DC BUS VOLTAGES
XXX XXX VDC
(4 circuit)
INTERNAL AMBIENT TEMP XXX.X DEGF
COOLING SYSTEM STATUS XXX
BASEPLATE TEMPS
XXX XXX DEGF
PRECHARGE SIGNAL
XXX
(2 circuit & 3 circuit)
PRECHARGE SIGNALS
XXX XXX
(4 circuit)
MOTOR OVERLOADS 1/2
XXX XXX AMPS
MOTOR OVERLOADS 3/4
XXX XXX AMPS
(3 circuit & 4 circuit)
SOFTWARE VERSION
C.VSD.XX.00
SYSTEM 1 DATA
COMPRESSOR STATUS
OFF
RUN TIME
0- 0- 0- 0 D-H-M-S
MOTOR CURRENT
0AMPS 0 %FLA
SUCTION PRESSURE
125 PSIG
DISCHARGE PRESSURE
131 PSIG
OIL PRESSURE
130 PSIG
SUCTION TEMPERATURE
68.4 DEGF
DISCHARGE TEMPERATURE 68.8 DEGF
OIL TEMPERATURE
68.8 DEGF
SAT SUCTION TEMP
71.8 DEGF
SUCTION SUPERHEAT
3.4 DEGF
SAT DISCHARGE TEMP
74.5 DEGF
DISCHARGE SUPERHEAT
6.3 DEGF
MOTOR TMP XXX.X XXX.X XXX.X DEGF
COMPRESSOR SPEED
XXX.X %
ECONOMIZER SOLENOID
OFF
FLASH TANK LEVEL
XXX.X %
FEED VALVE % OPEN
XXX.X %
DRAIN VALVE % OPEN
XXX.X %
CONDENSER FANS ON
0
COMPRESSOR HEATER
ON
RUN PERMISSIVE
ON
VSD RUN RELAY
OFF
VSD SOFTWARE RUN SIGNAL OFF
SYSTEM 2 DATA
COMPRESSOR STATUS
ON
RUN TIME
0-0-15-26 D-H-M-S
MOTOR CURRENT
104 AMPS
87 %FLA
SUCTION PRESSURE
57 PSIG
DISCHARGE PRESSURE
233 PSIG
OIL PRESSURE
218 PSIG
SUCTION TEMPERATURE
42.9 DEGF
DISCHARGE TEMPERATURE
145.5 DEGF
OIL TEMPERATURE
102.8 DEGF
SAT SUCTION TEMP
31.7 DEGF
SUCTION SUPERHEAT
11.2 DEGF
SAT DISCHARGE TEMP
112.1 DEGF
DISCHARGE SUPERHEAT
33.4 DEGF
MOTOR TMP
XXX.X XXX.X XXX.X DEGF
COMPRESSOR SPEED
XXX.X%
LIQUID LINE SOLENOID
ON
283

MICROPANEL
FORM 201.23-NM1 (910)

FLASH TANK LEVEL


FEED VALVE % OPEN
DRAIN VALVE % OPEN
CONDENSER FANS ON
COMPRESSOR HEATER
RUN PERMISSIVE
VSD RUN RELAY
VSD SOFTWARE RUN SIGNAL

XXX.X %
XXX.X %
XXX.X %
3
OFF
ON
OFF
OFF

UNIT OPERATING SCHEDULE


S M T W T F S
*=HOLIDAY
MON START=00:00AM
STOP=00:00AM
TUE START=00:00AM
STOP=00:00AM
WED START=00:00AM
STOP=00:00AM
THU START=00:00AM
STOP=00:00AM
FRI START=00:00AM
STOP=00:00AM
SAT START=00:00AM
STOP=00:00AM
HOL START=00:00AM
STOP=00:00AM
SOUND LIMIT SCHEDULE
(This section is printed only if the
sound limit schedule is enabled)
MON START=00:00AM
STOP=00:00AM
TUE START=00:00AM
STOP=00:00AM
WED START=00:00AM
STOP=00:00AM
THU START=00:00AM
STOP=00:00AM
FRI START=00:00AM
STOP=00:00AM
SAT START=00:00AM
STOP=00:00AM
HOL START=00:00AM
STOP=00:00AM

History Data Printout


History printouts, when selected, provide stored data
relating to all specific system and chiller operating conditions at the time of the fault, regardless of whether
a lockout occurred. History information is stored in
battery-backed memory on the Chiller Control Board
and is not affected by power failures or resetting of
faults. Whenever a fault of any type occurs, all system
operating data is stored in battery-backed memory at
the instant of the fault. The history printout is similar
to the operating data printout except for the change in
the header information shown below:
YORK INTERNATIONAL CORPORATION
LATITUDE SCREW CHILLER
HISTORY NUMBER 1
2:04:14 PM 18 FEB 10
SYS 1 YYYYYYY
HIGH DSCH PRESS SHUTDOWN
STATUS AT TIME OF SHUTDOWN
SYS 1 XXXXXXXXXXXXXXXXXXXXXXXXXX
SYS 2 XXXXXXXXXXXXXXXXXXXXXXXXXX
ALL FAULTS
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

The most recent fault will always be stored as HISTORY BUFFER #1.

284

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SERVICE KEY

service
KEy

8
LD10605

Service Key Operation


The SERVICE key allows viewing data related to the
internal function of the chiller system electronics.
Data such as circuit board output status as controlled
by the Chiller Control software while operating can be
viewed and compared to actual chiller operation in the
event servicing is required. The SERVICE key allows
controlling of analog and digital outputs for troubleshooting purposes when the unit is not running. The
Unit Serial Number and Optimized IPLV Control mode
are also entered using the SERVICE key.
The (ARROW) keys allow scrolling through the
displays. The (ARROW) key scrolls through the
displays in the forward direction.
When the SERVICE key is pressed, the following message will appear:
SERVICE MODE XXXX
PRESS ENTER KEY TO CONTINUE

XXXX will display a password, if a numerical password is entered.


Pressing the (ENTER) key allows view only Service Mode operation. All control board I/O will be

JOHNSON CONTROLS

viewable in this mode. No outputs can be changed.


For troubleshooting or start-up commissioning purposes, the Chiller Micro Board and some VSD outputs
can be toggled or changed by turning off the UNIT
SWITCH, pressing the SERVICE key, entering password 9675, and pressing the (ENTER) key. Once
the password is entered, the Digital Outputs (DO) can
be toggled by pressing the (ENTER) key. The Analog Outputs can be programmed to output a specific
value using the keypad and programming in the desired
value, which will usually be noted as a % or VDC. If
the UNIT SWITCH is turned back on, the chiller will
revert to normal viewable only control.
Displays can be viewed by pressing the and (ARROW) keys. The (arrow) key scrolls through
the displays in the forward direction.
The and (ARROW) keys allow jumping from
data section to data section to avoid scrolling sequentially through all the data. Once in a data section, the
and (ARROW) keys allow scrolling through the
data under the section. Pressing the and (ARROW) keys at any time moves to the top of the next
data section.

285

MICROPANEL
FORM 201.23-NM1 (910)

The data sections are listed below:


Software Versions
Analog Inputs
Digital Inputs
Digital Outputs
Analog Outputs
VSD Logic Digital Output
SERVICE

If the input is programmed for a current input, the voltage read by the MUX is displayed. If the input is disabled under the OPTIONS key, the voltage display will
display DISABLED.

SOFTWARE VERSIONS

CONTROL = C.AXX.ZZ.YY

VSD = C.VXX.ZZ.YY

The software version of the chiller Micro Control


Board and the VSD microprocessor are viewable in the
first data section.
XX, YY, and ZZ will be filled in with alphanumeric
characters.
The second data section displays the Analog Inputs
(AI). Displays for 3 and 4 compressor chillers are
skipped if the unit does not have those systems. These
messages will only be displayed in English. The voltage
displayed is referenced to common (return, ground) in
the system. J12-3 can also be used as common, as well
as chassis ground, or the common terminal point on the
Chiller Control Board. See the wiring diagrams.
SERVICE AI J17-11 REMOTE TEMP RESET

X.X VDC

= XXX.X %

SERVICE AI J17-12 REMOTE CURRENT LIMIT


X.X VDC

= XXX.X %

SERVICE AI J17-13 REMOTE SOUND LIMIT


X.X VDC

= XXX.X %

The Remote Temp Reset, Remote Current Limit Reset,


and Remote Sound Limit inputs have onboard voltage
dividers, if the jumper is set for a voltage input. This
will cause the voltage read on the display to be less
than the voltage on the board header inputs between
TB1-17 and 18, TB1-19 and 20, or TB1-40 and 41). To
correct for this when measuring voltage at the remote
device supplying voltage to the board header while
troubleshooting, use the following calculation:

286

The analog inputs display will continue to sequence as


follows. The inputs indicate voltages read between the
input terminal to the Chiller Logic Board and the plug
GND or Drain.
SERVICE AI J17-14 SPARE ANALOG 1
X.X VDC
SERVICE AI J17-15 SPARE ANALOG 2
X.X VDC
SERVICE AI J18-7 LEAVING LIQUID TEMP
X.X VDC

= XXX.X F

SERVICE AI J18-8 return LIQUID TEMP


X.X VDC

= XXX.X F

SERVICE AI J18-9 ambient air TEMP


X.X VDC

= XXX.X F

SERVICE AI J19-1 sys1 motor TEMP t1


X.X VDC

= XXX.X F

SERVICE AI J19-2 sys1 motor TEMP t2


X.X VDC

= XXX.X F

SERVICE AI J19-3 sys1 motor TEMP t3


X.X VDC

= XXX.X F

SERVICE AI J19-6 sys2 motor TEMP t1


X.X VDC

= XXX.X F

SERVICE AI J19-7 sys2 motor TEMP t2


X.X VDC

= XXX.X F

SERVICE AI J19-8 sys2 motor TEMP t3


X.X VDC

= XXX.X F

SERVICE AI J20-1 sys3 motor TEMP t1


X.X VDC

= XXX.X F

SERVICE AI J20-2 sys3 motor TEMP t2


X.X VDC

= XXX.X F

Voltage = 10 x VDC volts / 4.5

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SERVICE AI J20-3 sys3 motor TEMP t3

SERVICE AI J22-22 sys2 oil press

X.X VDC

X.X VDC

= XXX.X F

SERVICE AI J20-6 sys4 motor TEMP t1


X.X VDC

= XXX.X F

= XXX.X psig

SERVICE AI J22-24 sys2 discharge press


X.X VDC

= XXX.X psig

SERVICE AI J20-7 sys4 motor TEMP t2


X.X VDC

= XXX.X F

SERVICE AI J20-8 sys4 motor TEMP t3


X.X VDC

= XXX.X F

SERVICE AI J23-3 sys3 oil temp


X.X VDC

SERVICE AI J23-6 sys3 fl tank level


X.X VDC

SERVICE AI J21-3 sys1 oil TEMP


X.X VDC

= XXX.X F

SERVICE AI J21-6 sys1 fl tank level


X.X VDC

= XXX.X %

= XXX.X F

= XXX.X %

SERVICE AI J23-13 sys3 suction temp


X.X VDC

= XXX.X F

SERVICE AI J23-16 sys3 discharge temp


X.X VDC

= XXX.X F

SERVICE AI J21-13 sys1 suction temp

SERVICE AI J23-20 sys3 sucTion press

X.X VDC

X.X VDC

= XXX.X F

SERVICE AI J21-16 sys1 discharge temp


X.X VDC

= XXX.X F

= XXX.X psig

SERVICE AI J23-22 sys3 oil press


X.X VDC

= XXX.X psig

SERVICE AI J21-20 sys1 suction press

SERVICE AI J23-24 sys3 discharge press

X.X VDC

X.X VDC

= XXX.X psig

= XXX.X psig

SERVICE AI J21-22 sys1 oil press


X.X VDC

= XXX.X psig
SERVICE AI J24-3 sys4 oil temp

SERVICE AI J21-24 sys1 discharge press


X.X VDC

X.X VDC

= XXX.X F

= XXX.X psig
SERVICE AI J24-6 sys4 fl tank level
X.X VDC

SERVICE AI J22-3 sys2 oil temp


X.X VDC

= XXX.X F

SERVICE AI J22-6 sys2 fl tank level


X.X VDC

= XXX.X %

SERVICE AI J22-13 sys2 suction temp


X.X VDC

= XXX.X F

SERVICE AI J22-16 sys2 discharge temp


X.X VDC

= XXX.X F

= XXX.X %

SERVICE AI J24-13 sys4 suction temp


X.X VDC

= XXX.X F

SERVICE AI J24-16 sys4 discharge temp


X.X VDC

= XXX.X F

SERVICE AI J24-20 sys4 suction press


X.X VDC

= XXX.X psig

SERVICE AI J24-22 sys4 oil press


X.X VDC

= XXX.X psig

SERVICE AI J22-20 sys2 suction press

SERVICE AI J24-24 sys4 discharge press

X.X VDC

X.X VDC

JOHNSON CONTROLS

= XXX.X psig

= XXX.X psig

287

MICROPANEL
FORM 201.23-NM1 (910)

The third data section displays the Digital Inputs (DI)


to the Chiller Control Board that can be viewed from
the Service Mode. Displays for systems 3 and 4 are
skipped if the systems are not present on the chiller.
XXX is replaced with ON or OFF in the actual display.
These messages will only be displayed in English.
SERVICE DI J4-2 unit switch 1
status = xxx
SERVICE DI J4-3 unit switch 2
status = xxx

SERVICE DI J7-2 config input 0


status = xxx
SERVICE DI J7-4 config input 1
status = xxx
SERVICE DI J7-6 config input 2
status = xxx
SERVICE DI J7-8 config input 3
status = xxx
SERVICE DI J7-10 config spare input 0
status = xxx

SERVICE DI J4-4 sys 1 hpco

SERVICE DI J7-12 config spare input 1

status = xxx

status = xxx

SERVICE DI J4-5 sys 2 hpco


status = xxx
SERVICE DI J4-6 vsd fault relay
status = xxx

SERVICE Do J9-1 evap heater


rb1 tb1-20 status = xxx
SERVICE Do J9-2 sys 1/3 vsd run
rb1 tb1-18 status = xxx
SERVICE Do J9-3 sys 1/3 alarm

SERVICE DI J5-1 sys 3 hpco


status = xxx
SERVICE DI J5-2 sys 4 hpco
status = xxx
SERVICE DI J5-3 spare digital input 2
status = xxx

J5 is not present on a 2 compressor Chiller Control


Board. The displays above are skipped for a 2 compressor chiller:
SERVICE DI J6-2 flow switch
status = xxx
SERVICE DI J6-3 print
status = xxx
SERVICE DI J6-4 sys 1/3 run perm
status = xxx
SERVICE DI J6-5 sys 2/4 run perm
status = xxx

rb1 tb1-16 status = xxx


SERVICE Do J9-4 evap heater 2
rb1 tb1-14 status = xxx
SERVICE Do J9-5 sys 1 spare
rb1 tb1-12 status = xxx
SERVICE Do J9-6 spare 1
rb1 tb1-10 status = xxx
SERVICE Do J9-7 spare 2
rb1 tb1-8 status = xxx
SERVICE Do J9-8 sys 1 cond fan out 1
rb1 tb1-6 status = xxx
SERVICE Do J9-9 sys 1 cond fan out 2
rb1 tb1-5 status = xxx
SERVICE Do J9-10 sys 1 cond fan out 3

rb1 tb1-4 status = xxx

SERVICE Do J9-11 sys 1 comp heater


rb1 tb1-3 status = xxx

SERVICE DI J6-6 spare digital input 1

SERVICE Do J9-10 sys 1 econ sol valve

status = xxx

288

rb1 tb1-2 status = xxx

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SERVICE Do J10-1 evap pump run

SERVICE Do J11-6 sys 4 spare

rb1 tb1-20 status = xxx

rb1 tb1-10 status = xxx

SERVICE Do J10-2 sys 2/4 vsd run

SERVICE Do J11-7 sys 3 spare

rb1 tb1-18 status = xxx


SERVICE Do J10-3 sys 2/4 alarm
rb1 tb1-16 status = xxx

rb1 tb1-8 status = xxx

SERVICE Do J11-8 sys 3 cond fan out 1


rb1 tb1-6 status = xxx

SERVICE Do J10-4 chiller run

SERVICE Do J11-9 sys 3 cond fan out 2

rb1 tb1-14 status = xxx

SERVICE Do J10-5 sys 2 spare

SERVICE Do J11-10 sys 3 cond fan out 3

rb1 tb1-12 status = xxx

SERVICE Do J10-6 spare 3

SERVICE Do J11-11 sys 3 comp heater

rb1 tb1-10 status = xxx

rb1 tb1-3 status = xxx

SERVICE Do J10-7 spare 4

SERVICE Do J11-12 sys 3 econ sol valve

rb1 tb1-8 status = xxx

SERVICE Do J10-8 sys cond 2 fan out 1


rb1 tb1-6 status = xxx

SERVICE Do J10-9 sys cond 2 fan out 2


rb1 tb1-5 status = xxx

SERVICE Do J10-10 sys cond 2 fan out 3


rb1 tb1-4 status = xxx

SERVICE Do J10-11 sys 2 comp heater


rb1 tb1-3 status = xxx

SERVICE Do J10-12 sys 2 econ sol valve


rb1 tb1-2 status = xxx

SERVICE Do J11-1 sys 4 cond fan out 1


rb1 tb1-20 status = xxx

rb1 tb1-5 status = xxx

rb1 tb1-4 status = xxx

rb1 tb1-2 status = xxx

The fifth data section displays the Analog Outputs


(AO) that can be viewed from the Service Mode. The
Analog Output signals are typically referenced to the
common (return, ground) in the system. J12-3 can also
be used as common, as well as chassis ground, or the
common terminal point on the Chiller Control Board.
See the wiring diagrams. GND on the plug. Displays
for systems 3 and 4 are skipped if the systems are not
present on the chiller. XXX is replaced with ON or
OFF in the actual display. The state of these outputs
is only viewable unless the password 9675 (ENTER)
key was entered from the initial Service Mode display
with the UNIT switch in the OFF position. The chiller will not be permitted to run when the outputs are
made active. The outputs can be programmed for a
specific % output by keying in the value and pressing
the (ENTER) key. These messages will only be displayed in English.

SERVICE Do J11-2 sys 4 cond fan out 2

SERVICE Ao J15-1 sys 1 feed valve out

rb1 tb1-18 status = xxx

SERVICE Do J11-3 sys 4 cond fan out 3

SERVICE Ao J15-3 sys 1 drain valve out

xxx.x %

rb1 tb1-16 status = xxx

SERVICE Do J11-4 sys 4 comp heater

SERVICE Ao J15-5 sys 2 feed valve out

rb1 tb1-14 status = xxx

SERVICE Do J11-5 sys 4 econ sol valve

SERVICE Ao J15-7 sys 2 drain valve out

rb1 tb1-12 status = xxx

JOHNSON CONTROLS

xxx.x %

= xx.x VDC

xxx.x %

xxx.x %

= xx.x VDC

= xx.x VDC

= xx.x VDC

289

MICROPANEL
FORM 201.23-NM1 (910)

SERVICE Ao J14-1 sys 3 feed valve out


xxx.x %

= xx.x VDC

SERVICE Ao J14-2 sys 3 drain valve out


xxx.x %

= xx.x VDC

SERVICE Ao J14-3 sys 4 feed valve out


xxx.x %

= xx.x VDC

SERVICE Ao J14-4 sys 4 drain valve out


xxx.x %

= xx.x VDC

SERVICE Ao J25-1 sys 1 spare


xxx.x %

= xx.x VDC

SERVICE Ao J25-2 sys 2 spare


xxx.x %

= xx.x VDC

SERVICE Ao J25-3 sys 3 spare


xxx.x %

= xx.x VDC

SERVICE Ao J25-4 sys 4 spare


xxx.x %

= xx.x VDC

The sixth data section displays the VSD digital outputs (DO) that can be viewed from the Service Mode.
The Digital Output signals indicate the status of the
output. The 0 to 120VAC digital outputs are referenced
to neutral (Wire 2).
SERVICE Do J10-2 vsd cooling fan/pump
vsd logic staTus = xxx

290

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

SYSTEM SWITCHES KEY

system
switches
KEy

LD10605

System Switches Key Operation


The SYSTEM SWITCHES key allows the operator to
turn individual systems ON and OFF. Safety lockouts are also reset by selecting the respective system
switch RESET. When the SYSTEM SWITCHES key
is pressed, the following message will appear:
system switches sys 1 on / off / reset

=xXXXxXXXxxxxxXx

The display indicates the respective system and its on/


off /reset switch status. The (ARROW) keys allow scrolling to the next and previous system switch
(System 1, 2, 3, or 4).
system switches sys 2 on / off / reset

=xXXXxXXXxxxxxXx

system switches sys 3 on / off / reset


=xXXXxXXXxxxxxXx

system switches sys 4 on / off / reset


JOHNSON CONTROLS

=xXXXxXXXxxxxxXx

The (LEFT ARROW) or (RIGHT ARROW) keys


allow scrolling through the choices of:
SYSTEM OFF (default)
SYSTEM ON
RESET (LOCKOUT)
The switch selection is accepted into memory by pressing the (ENTER) key.
When the RESET selection is made and accepted, it
will not change the position of the switch (either ON
or OFF).

Whenever possible, except in emergencies, always use the associated


system switch to turn off a compressor,
which allows the compressors to go
through a controlled shutdown. Avoid
using the "UNIT" switch to turn off
the compressors.

291

MICROPANEL
FORM 201.23-NM1 (910)

Serial Number Programming


When changing a Chiller Control Board, a Chiller
Control Board EPROM, or if a situation occurs where
a chiller is not programmed from the factory, the chiller serial number will need to be programmed into the
chiller. The serial number is the actual serial number
displayed on the unit Data Plate. The serial number
will be in a format similar to RABM000000, where the
first 4 characters are letters and the next 6 are numbers.
The lack of a serial number programmed into the panel
will not prevent a chiller from operating, but a High
IPLV chiller will only operate in the Standard IPLV
mode. The STATUS display will inform the operator a
serial number problem exists by displaying the following message:
unit warning: invalid serial number
enter unit serial number

If the following message appears, immediately contact


Johnson Controls Product Technical Support. The appearance of this message may also mean the chiller has
lost important factory programmed information and
may need to be reprogrammed. Additional STATUS
messages can be viewed by pressing the STATUS key
repetitively to enable the technician to view any other
messages that may be preventing the chiller from operating.

Changing the programming of this


feature requires the date and time to
be set on the chiller prior to programming. The password is also time
sensitive and must be used the same
day it is received.
Johnson Controls Product Technical Support will provide a factory password to allow programming the
serial number into the chiller. You will need to supply Factory Technical Support with the version of the
Chiller Control Board EPROM. The version will be
written on the EPROM label and typically will be in
the format Version C.ACS.XX.XX.
After obtaining the password, the following steps will
need to be followed to input the serial number. As the
serial number is input, the characters keyed in will appear in the display indicating the panel has recognized
the entry.

292

First press the SERVICE key. The following message


will appear:
service mode

xxxxx

press enter key to continue

Key in the 5 digit alphanumeric password provided by


Product Technical Support and press the (ENTER)
key. The following display will appear:
s/n entry unit serial number pos 1
x

Key in the first letter (A through Z) of the serial number using the and (ARROW) keys and press the
(ENTER) key. Press the (Down ARROW) key
to scroll to position 2 and the following message will
appear:
s/n entry unit serial number pos 2
xx

Key in the second letter (A through N) of the serial


number using the and (ARROW) keys and press
the (ENTER) key. Press the (Down ARROW)
key to scroll to position 3 and the following message
will appear:
s/n entry unit serial number pos 3
xxx

Key in the third letter (A through Z) of the serial number using the and (ARROW) keys and press the
(ENTER) key. Press the (Down arrow) key
to scroll to position 4 and the following message will
appear:
s/n entry unit serial number pos 4
xxxx

Key in the fourth letter (A through Z) of the serial number using the and (ARROW) keys and press the
(ENTER) key. Press the (Down arrow) key
to scroll to positions 5-7 and the following message
will appear:
s/n entry unit s/n = yyyY xxx zzz
unit serial number pos 5-7 = xxx

At this point, the letters entered for the YYYY inputs


should now appear in the top line of the display and
should match the first 4 characters of the serial number
on the unit Data Plate. The next three digits of the
serial number should now be keyed in. Press the
(ENTER) key to store the input. Press the (DOWN
ARROW) key to scroll to positions 8 through10 and
the following message will appear:

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

s/n entry unit s/n = yyYy xxx zzz


unit serial number pos 8-10 = xxx

At this point, the letters entered for the YYYY and


XXX inputs should now appear in the top line of the
display and should match the first 7 characters of the
serial number on the unit Data Plate. The next three
digits of the serial number should now be keyed in.
Press the (ENTER) key to store the input. The full
serial number should now be displayed across the top
of the display and the cursor should disappear.
Press the STATUS key to go to the next STATUS display to determine if additional Status messages are preventing the chiller from operating.
enabling optimized high iplv mode
When changing a Chiller Control Board, a Chiller
Control Board EPROM, or if a situation occurs where
a chiller is not programmed from the factory, the chiller will not be capable of operating High IPLV mode.
The serial number of the unit will first need to be programmed into the panel, if the Invalid Serial Number
display appears (see Page 292). The Invalid Serial
Number message will override the Optimized Efficiency Disabled message. If the chiller was purchased
with the High IPLV Option and does not have the High
IPLV mode enabled, it will not prevent the chiller from
operating, but the chiller will only operate in the Standard IPLV mode. Additional STATUS messages can
be viewed by pressing the STATUS key repetitively to
enable the technician to view any other messages that
may be preventing the chiller from operating.

Changing the programming of this


feature requires the date and time to
be set on the chiller prior to programming the password. The password is
also time sensitive and must be used
immediately when it is received.

JOHNSON CONTROLS

The STATUS display will inform the operator when


a High IPLV chiller is operating with the High IPLV
mode disabled by displaying the following STATUS
message:
unit waring: optimzed efficiency
disabled - contact york represenative

If the message above appears, immediately contact


Johnson Controls Product Technical Support or Johnson Controls ES Commercial for a password to enable
the High IPLV mode. You will need to provide Johnson Controls Product Technical Support or Johnson
Controls ES Commercial with the Unit Serial Number
located on the chiller nameplate. The date and time
will also need to be current on the chiller, and will need
to be provided to Johnson Controls Product Technical
Support or Johnson Controls ES Commercial. It is essential Johnson Controls Product Technical Support
or, Johnson Controls ES Commercial is aware of the
local time to allow adjustments for time differences
from Eastern Standard Time.

After obtaining the password, the following steps will need to be carried out
immediately to input the serial number. If the password is not immediately input, the panel will not accept
it.
To enable HIGH IPLV Mode, first press the SERVICE
key. The following message will appear:
service mode

xxxxx

press enter key to continue

Key in the 6 digit alphanumeric password provided by


Johnson Controls Technical Support or Johnson Controls ES Commercial and press the (ENTER) key.
The following display will appear:
iplv optimzed efficiency control
xxxxxxxxxxxXXXxXXXxxxxxXx

When the Optimized (High IPLV) is enabled, the display will indicate, ENABLED. When not enabled,
the display will indicate, DISABLED. Use the
and (ARROW) keys to enable/disable and press the
(ENTER) key to store the selection.

293

MICROPANEL
FORM 201.23-NM1 (910)

unit setup mode


Unit Setup Mode will allow the programming all of
the programmable values that the user should never
change. These will either be programmed at the factory or by service personnel on the job.

This mode may be entered by pressing the PROGRAM


key, entering the password 4245, and pressing the
(ENTER) key. TABLE 19 lists the values that can
be programmed in this mode. Details relating to the
actual message follow the table.

TABLE 19 - unit setup programmable values


setup mode value

programmable range

default

Sys 1 Number of Cond Fans

4 to 6

Sys 2 Number of Cond Fans

4 to 6

Sys 3 Number of Cond Fans

4 to 6

Sys 4 Number of Cond Fans

4 to 6

Compressor 1 Operating hours

0 to 99,999

Compressor 2 Operating hours

0 to 99,999

Compressor 3 Operating hours

0 to 99,999

Compressor 4 Operating hours

0 to 99,999

Compressor 1 Starts

0 to 99,999

Compressor 2 Starts

0 to 99,999

Compressor 3 Starts

0 to 99,999

Compressor 4 Starts

0 to 99,999

Clear History Buffers

Yes/ No

Remote Temp Reset Option

Disabled/Enabled

Disabled

Remote Current Limit Option

Disabled/Enabled

Disabled

Sound Limit Option

Disabled/Enabled

Disabled

Remote Inputs Service Time

5 Min - 60 Min

15 Min

Sys 1 Motor Sensor to Ignore

See Below

None

Sys 2 Motor Sensor to Ignore

See Below

None

Sys 3 Motor Sensor to Ignore

See Below

None

Sys 4 Motor Sensor to Ignore

See Below

None

The following messages will be displayed for the Unit


Setup Mode in the order they appear. The first group of
displays relates to setup parameters that relate to unit
configuration and factory setpoints.
setup mode def xxxxx lo xxxxx hi xxxxx

setup mode def xxxxx lo xxxxx hi xxxxx

Sys 1 number of cond fans

comp 1 operating hours

=x

setup mode def xxxxx lo xxxxx hi xxxxx


Sys 2 number of cond fans

=x

setup mode def xxxxx lo xxxxx hi xxxxx


Sys 3 number of cond fans

=x

setup mode def xxxxx lo xxxxx hi xxxxx


Sys 4 number of cond fans

294

=x

= xxxxx

setup mode def xxxxx lo xxxxx hi xxxxx


comp 2 operating hours

= xxxxx

setup mode def xxxxx lo xxxxx hi xxxxx


comp 3 operating hours

= xxxxx

setup mode def xxxxx lo xxxxx hi xxxxx


comp 4 operating hours

= xxxxx

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

setup mode def xxxxx lo xxxxx hi xxxxx

setup mode sys 4 motor sensor to ignore

comp 1 starts

xxxxxxxxxxxxxxxxxxxxxxxxx

= xxxxx

setup mode def xxxxx lo xxxxx hi xxxxx


comp 2 starts

= xxxxx

setup mode def xxxxx lo xxxxx hi xxxxx


comp 3 starts

= xxxxx

setup mode def xxxxx lo xxxxx hi xxxxx


comp 4 starts

= xxxxx

The following setup display is selectable as YES or


NO using the and (ARROW) keys.
setup mode clear history buffers?
xxxxxxxxxxxxxxxxxxxxxxxx

The following (3) setup OPTION displays are selectable as ENABLED or DISABLED using the and
(ARROW) keys according to the options installed on
the chiller:
setup mode remote temp reset option
xxxxxxxxxxxxxxxxxxxxxxxx
setup mode remote current limit option
xxxxxxxxxxxxxxxxxxxxxxxx
setup mode sound limit option
xxxxxxxxxxxxxxxxxxxxxxxx

The following setup OPTION display is selectable as


ENABLED or DISABLED using the and (ARROW) keys:
setup mode def xxxxx lo xxxxx hi xxxxx
remote inputs service time

= xx min

The following OPTION displays are selectable as ENABLED or DISABLED using the and (ARROW)
keys. The choices are:
NONE (default)
TEMP SENSOR 1
TEMP SENSOR 2
TEMP SENSOR 3
setup mode sys 1 motor sensor to ignore
xxxxxxxxxxxxxxxxxxxxxxxxx
setup mode sys 2 motor sensor to ignore
xxxxxxxxxxxxxxxxxxxxxxxxx

If a motor temperature sensor fails, a single sensor may


be ignored by making a program change in the Unit
Setup Mode. The default setting is NONE, indicating all sensors are being monitored.
default programmable values
To quickly program or reset most of the user programmable values to their default values, press PROGRAM,
6140, ENTER. The following message will then be
displayed, allowing a choice to reset the operating parameters to their default values.
defaults set prog values to default?
xxx

YES or NO may be selected for XXX using the and


(ARROW) keys to change the selection.
Following is a list of the operating parameters that will
be reset to their default values:
Suction Pressure Cutout = 24.0 PSIG
Low Ambient Air Temp Cutout = 25F
Leaving Chilled Liquid Temp Cutout = 36F
High Motor Current Limit = 100%
Pulldown Current Limit = 100%
Pulldown Current Limit Time = 0 Min.
Suction Superheat Setpoint = 10F
Sound limit Setpoint = 0%
serial port connections
TABLE 20 lists the serial ports and the circuit board
they are located on. The serial communications lines
provide communications to external devices outside
the chiller and between microprocessors located in the
chiller control panel.
TB2 allows connecting to a remote OptiView RCC or
Microgateway. The OptiView RCC option is not yet
available. The OptiView RCC and Microgateway option cannot both be used. Only one or the other is permitted to be connected to the chiller.

setup mode sys 3 motor sensor to ignore


xxxxxxxxxxxxxxxxxxxxxxxxx

JOHNSON CONTROLS

295

MICROPANEL
FORM 201.23-NM1 (910)

TABLE 20 - serial port connections


BOARD

HEADER

PORT TYPE

PORT USE

Chiller Control Board

TB1 / TB2

RS-232 / RS-485

Printer/RCC and ISN

Chiller Control Board

J2 / J1

RS-485

Control Panel <-> VSD #1 / #2

VSD Logic Board

J12

Opto- Coupled RS-485

VSD <-> Control Panel

analog input connections


TABLE 21 lists the Analog inputs and the circuit board
they are located on. Not all of the sensors are installed
in every unit, as some of them are optional. The software must read the optional sensors if installed. The
Analog input signals are typically referenced to the
common (return, ground) in the system.

J12-3 can also be used as common, as well as chassis


ground, or the common terminal point on the Chiller
Control Board. See the wiring diagrams. The +DC
Bus, -DC Bus and DC Bus voltages are measured
in reference to one of the other DC Bus points. For
example: +DC Bus measured to DC Bus.

TABLE 21 - analog input connections

296

BOARD

HEADER

ANALOG INPUT

Chiller Control Board

J17-11

Remote Temperature Reset

Chiller Control Board

J17-12

Remote Current Limit

Chiller Control Board

J17-13

Spare 1

Chiller Control Board

J17-14

Spare 2

Chiller Control Board

J17-15

Spare 3

Chiller Control Board

J8-7

Leaving Chilled Liquid Temp Sensor

Chiller Control Board

J8-8

Return Chilled Liquid Temp Sensor

Chiller Control Board

J8-9

Ambient Air Temp Sensor

Chiller Control Board

J19-1

Comp 1 Motor Temperature 1

Chiller Control Board

J19-2

Comp 1 Motor Temperature 2

Chiller Control Board

J19-3

Comp 1 Motor Temperature 3

Chiller Control Board

J19-6

Comp 2 Motor Temperature 1

Chiller Control Board

J19-7

Comp 2 Motor Temperature 2

Chiller Control Board

J19-8

Comp 2 Motor Temperature 3

Chiller Control Board

J21-13

Sys 1 Suction Temperature

Chiller Control Board

J21-3

Sys 1 Oil Temperature

Chiller Control Board

J21-16

Sys 1 Discharge Temperature

Chiller Control Board

J21-6

Sys 1 Flash Tank Level Sensor

Chiller Control Board

J21-20

Sys 1 Suction Pressure

Chiller Control Board

J21-22

Sys 1 Oil Pressure

Chiller Control Board

J21-24

Sys 1 Discharge Pressure

Chiller Control Board

J22-13

Sys 2 Suction Temperature

Chiller Control Board

J22-2

Sys 2 Oil Temperature

Chiller Control Board

J22-16

Sys 2 Discharge Temperature

Chiller Control Board

J22-6

Sys 2 Flash Tank Level Sensor

Chiller Control Board

J22-20

Sys 2 Suction Pressure

Chiller Control Board

J22-22

Sys 2 Oil Pressure

Chiller Control Board

J22-24

Sys 2 Discharge Pressure

Chiller Control Board

J20-1

Comp 3 Motor Temperature 1

Chiller Control Board

J20-2

Comp 3 Motor Temperature 2

Chiller Control Board

J20-3

Comp 3 Motor Temperature 3

Chiller Control Board

J20-6

Comp 4 Motor Temperature 1

Chiller Control Board

J20-7

Comp 4 Motor Temperature 2

Chiller Control Board

J20-8

Comp 4 Motor Temperature


JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE 21 - analog input connections (CONT'D)


BOARD

HEADER

ANALOG INPUT

Chiller Control Board

J23-13

Sys 3 Suction Temperature

Chiller Control Board

J23-3

Sys 3 Oil Temperature

Chiller Control Board

J23-16

Sys 3 Discharge Temperature

Chiller Control Board

J23-6

Sys 3 Flash Tank Level Sensor

Chiller Control Board

J23-20

Sys 3 Suction Pressure

Chiller Control Board

J23-22

Sys 3 Oil Temperature

Chiller Control Board

J23-24

Sys 3 Discharge Pressure

Chiller Control Board

J24-13

Sys 4 Suction Temperature

Chiller Control Board

J24-3

Sys 4 Oil Temperature

Chiller Control Board

J24-16

Sys 4 Discharge Temperature

Chiller Control Board

J24-6

Sys 4 Flash Tank Level Sensor

Chiller Control Board

J24-20

Sys 4 Suction Pressure

Chiller Control Board

J24-22

Sys 4 Oil Pressure

Chiller Control Board

J24-24

Sys 4 Discharge Pressure

VSD Logic Board

J1-1 to J1-2

Comp 1 Phase A Motor Current

VSD Logic Board

J1-3 to J3-4

Comp 1 Phase B Motor Current

VSD Logic Board

J1-5 to J1-6

Comp 1 Phase C Motor Current

VSD Logic Board

J1-13 to J1-14

Comp 3 Phase A Motor Current

VSD Logic Board

J1-15 to J1-16

Comp 3 Phase B Motor Current

VSD Logic Board

J1-17 to J1-18

Comp 3 Phase C Motor Current

VSD Logic Board

J2-1 to J2-2

Comp 2 Phase A Motor Current

VSD Logic Board

J2-3 to J2-4

Comp 2 Phase B Motor Current

VSD Logic Board

J2-5 to J2-6

Comp 2 Phase C Motor Current

VSD Logic Board

J2-9 to J2-10

Comp 4 Phase A Motor Current

VSD Logic Board

J2-11 to J2-12

Comp 4 Phase B Motor Current

VSD Logic Board

J2-13 to J2-14

Comp 4 Phase C Motor Current

VSD Logic Board

J3-1

+DC Bus Voltage 1

VSD Logic Board

J3-2

1/2 DC Bus Voltage 1

VSD Logic Board

J3-3

-DC Bus Voltage 1

VSD Logic Board

J3-4

-DC Bus Voltage 2

VSD Logic Board

J3-5

1/2 DC Bus Voltage 2

VSD Logic Board

J3-6

+DC Bus Voltage 2

VSD Logic Board

J6-8

Comp 1 IGBT Baseplate Temperature

VSD Logic Board

J7-8

Comp 3 IGBT Baseplate Temperature

VSD Logic Board

J8-8

Comp 2 IGBT Baseplate temperature

VSD Logic Board

J9-8

Comp 4 IGBT Baseplate Temperature

VSD Logic Board

R19

Comp 1 Overload Adjust

VSD Logic Board

R42

Comp 3 Overload Adjust

VSD Logic Board

R64

Comp 2 Overload Adjust

VSD Logic Board

R86

Comp 4 Overload Adjust

JOHNSON CONTROLS

297

MICROPANEL
FORM 201.23-NM1 (910)

digital inTput connections


TABLE 22 lists the digital inputs and the circuit board
they are located on. The Digital input signals are typically referenced to the common (return, ground) in the
system.

J12-3 can also be used as common, as well as chassis


ground, or the common terminal point on the Chiller
Control Board. See the wiring diagrams.

TABLE 22 - digital input connections

298

BOARD

HEADER

ANALOG OUTPUT

Chiller Control Board

J4-2

Unit Switch 1

Chiller Control Board

J4-3

Unit Switch 2

Chiller Control Board

J4-4

Sys 1 HPCO

Chiller Control Board

J4-5

Sys 2 HPCO

Chiller Control Board

J4-6

VSD Fault Relay 1

Chiller Control Board

J5-1

Sys 3 HPCO

Chiller Control Board

J5-2

Sys 4 HPCO

Chiller Control Board

J5-3

VSD Fault Relay (Unused)

Chiller Control Board

J6-2

Flow Switch

Chiller Control Board

J6-3

Print

Chiller Control Board

J6-4

Sys 1/3 Run Permissive

Chiller Control Board

J6-5

Sys 2/4 Run Permissive

Chiller Control Board

J6-6

Spare

Chiller Control Board

J7-1 to J7-2

Config0

Chiller Control Board

J7-3 to J7-4

Config1

Chiller Control Board

J7-5 to J7-6

Config2

Chiller Control Board

J7-7 to J7-8

Config3

Chiller Control Board

J7-9 to J7-10

Spare 0

Chiller Control Board

J7-11 to J7-12

Spare 1

VSD Logic Board

J1-10

2 Compressor Select

VSD Logic Board

J1-11

3 Compressor Select

VSD Logic Board

J1-12

4 Compressor Select

VSD Logic Board

J5-1 to J5-2

VSD Logic Board

J5-3 to J5-4

VSD Logic Board

J6-2

Comp 1 Phase A Gate Driver Fault

VSD Logic Board

J6-5

Comp 1 Phase C Gate Driver Fault

VSD Logic Board

J6-12

Comp 1 Phase B Gate Driver Fault

VSD Logic Board

J7-2

Comp 3 Phase A Gate Driver Fault

VSD Logic Board

J7-5

Comp 3 Phase C Gate Driver Fault

VSD Logic Board

J7-12

Comp 3 Phase B Gate Driver Fault

VSD Logic Board

J7-2

Comp 2 Phase A Gate Driver Fault

VSD Logic Board

J7-5

Comp 2 Phase C Gate Driver Fault

VSD Logic Board

J7-12

Comp 2 Phase B Gate Driver Fault

VSD Logic Board

J8-2

Comp 4 Phase A Gate Driver Fault

VSD Logic Board

J8-5

Comp 4 Phase C Gate Driver Fault

VSD Logic Board

J8-12

Comp 4 Phase B Gate Driver Fault

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE 22 - digital intput connections (CONT'D)


BOARD

HEADER

ANALOG OUTPUT

VSD Logic Board

J11-2

Phase Loss Fault 1

VSD Logic Board

J11-6

Phase Loss Fault 2

VSD Logic Board

SW1

Test Pushbutton

VSD Logic Board

J10-5 to J10-6

Comp 1/3 Run (from control panel)

VSD Logic Board

J10-7 to J10-8

Comp 2/4 (from control panel)

analog OUTput connections


TABLE 23 lists the analog outputs and the circuit board
they are located on. The analog output signals are feed
to the associated control device from the 2 wires in the
associated plug.
TABLE 23 - analog output connections
BOARD

HEADER

ANALOG OUTPUT

Chiller Control Board

J15-1 to J15-2

Sys 1 Flash Tank Feed Valve

Chiller Control Board

J15-3 to J15-4

Sys 1 Flash tank Drain Valve

Chiller Control Board

J15-5 to J15-6

Sys 2 flash Tank Feed Valve

Chiller Control Board

J15-7 to J15-8

Sys 2 Flash Tank Drain Valve

Chiller Control Board

J14-1 to J14-6

Sys 3 Flash Tank Feed Valve

Chiller Control Board

J14-2 to J14-7

Sys 3 Flash Tank Drain Valve

Chiller Control Board

J14-3 to J14-8

Sys 4 Flash Tank Feed Valve

Chiller Control Board

J14-4 to J14-9

Sys 4 Flash Tank Feed Valve

Chiller Control Board

J25-1 to J25-5

Sys 1 Condenser Fan Speed (Future)

Chiller Control Board

J25-2 to J25-6

Sys 2 Condenser Fan Speed (Future)

Chiller Control Board

J25-3 to J25-7

Sys 3 Condenser Fan Speed (Future)

Chiller Control Board

J25-4 to J25-8

Sys 4 Condenser Fan Speed (Future)

JOHNSON CONTROLS

299

MICROPANEL
FORM 201.23-NM1 (910)

digital OUTput connections


TABLE 24 lists the digital outputs and the plug/terminals of the circuit board they originate from. Not all of
the outputs will be used on every unit. Signal levels
may be 12VDC, 120VAC, or a dry contact (no voltage)
closure). 120VAC signals typically may show only
one connection point; the other will be neutral (Wire
2). Outputs which reference multiple boards, such as
Chiller Control Board / Relay Board 1 indicate the
signal originates on the Chiller Control Board as a 0 to
12VDC digital signal (example: J9-1) that is then fed
to the Relay board and output as a dry contact closure

between TB1-20 and 19. In this case, outputs from


both boards are called out in the table.
The 0 to 120VAC single digital outputs from the Relay
Output Boards are referenced to neutral (Wire 2). For
example, the fan output on TB1-6 is a single 120VAC
output. The 0 to 12VDC outputs from the Chiller Control Board are referenced to common (return, ground)
in the system. J12-3 can also be used as common, as
well as chassis ground, or the common terminal point
on the Chiller Control Board. See the wiring diagrams.
Refer to the wiring diagrams whenever there is a requirement for tracing out these signals.

TABLE 24 - digital output connections

300

BOARD

HEADER

ANALOG OUTPUT

Chiller Control / Relay Board 1

J9-1 / TB1-20 and 19

Evaporator Heater

Chiller Control / Relay Board 1

J9-2 / TB1-18 and 17

Sys 1/3 VSD Run

Chiller Control / Relay Board 1

J9-3 / TB1-16 and 15

Sys 1/3 Alarm

Chiller Control / Relay Board 1

J9-4 / TB1-14 and 13

Evaporator Heater 2

Chiller Control / Relay Board 1

J9-5 / TB1-12 and 11

Sys 1 SPARE

Chiller Control / Relay Board 1

J9-6 / TB1-10 and 9

SPARE

Chiller Control / Relay Board 1

J9-7/ TB1-8 and 7

SPARE

Chiller Control / Relay Board 1

J9-8 / TB1-6

Sys 1 Condenser Fans Output 1

Chiller Control / Relay Board 1

J9-9 / TB1-5

Sys 1 Condenser Fans Output 2

Chiller Control / Relay Board 1

J9-10 / TB1-4

Sys 1 Condenser Fans Output 3

Chiller Control / Relay Board 1

J9-11 / TB1-3

Sys 1 Compressor Heater

Chiller Control / Relay Board 1

J9-12 / TB1-2

Sys 1 Economizer Solenoid Valve

Chiller Control / Relay Board 2

J10-1 / TB1- 20 and 19

Evaporator Pump Start

Chiller Control / Relay Board 2

J10-2 / TB1-18 and 17

Sys 2/4 VSD Run

Chiller Control / Relay Board 2

J10-3 / TB1-18 and 15

Sys 2/4 Alarm

Chiller Control / Relay Board 2

J10-4 / TB1-16 and 14

Chiller Run

Chiller Control / Relay Board 2

J10-5 / TB1-12 and 11

Sys 2 SPARE

Chiller Control / Relay Board 2

J10-6 / TB1-10 and 9

SPARE

Chiller Control / Relay Board 2

J10-7 / TB1-8 and 7

SPARE

Chiller Control / Relay Board 2

J10-8 / TB1-6

Sys 2 Condenser Fans Output 1

Chiller Control / Relay Board 2

J10-9 / TB1-5

Sys 2 Condenser Fans Output 2

Chiller Control / Relay Board 2

J10-10 / TB1-4

Sys 2 Condenser Fans Output 3

Chiller Control / Relay Board 2

J10-11 / TB1-3

Sys 2 Compressor Heater

Chiller Control / Relay Board 3

J10-12 / TB1-2

Sys 2 Economizer Solenoid Valve

Chiller Control / Relay Board 3

J11-1 / TB1-20 and 19

Sys 4 Condenser Fan Output 1

Chiller Control / Relay Board 3

J11-2 / TB1-18 and 17

Sys 4 Condenser Fan Output 2

Chiller Control / Relay Board 3

J11-3 / TB1-16 and 15

Sys 4 Condenser Fan Output 3

Chiller Control / Relay Board 3

J11-4 / TB1-14 and 13

Sys 4 Compressor Heater

Chiller Control / Relay Board 3

J11-5 / TB1-12 and 11

Sys 4 Economizer Solenoid Valve

Chiller Control / Relay Board 3

J11-6 / TB1-10 and 9

Sys 4 SPARE

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE 24 - digital output connections (CONT'D)


BOARD

HEADER

ANALOG OUTPUT

Chiller Control / Relay Board 3

J11-7 / TB1-8 and 7

Sys 3 SPARE

Chiller Control / Relay Board 3

J11-8 / TB1-6

Sys 3 Condenser Fans Output 1

Chiller Control / Relay Board 3

J11-9 / TB1-5

Sys 3 Condenser Fans Output 2

Chiller Control / Relay Board 3

J11-10 / TB1-4

Sys 3 Condenser Fans Output 3

Chiller Control / Relay Board 3

J11-11 / TB1-3

Sys 3 Compressor Heater

Chiller Control / Relay Board 3

J11-12 / TB1-2

Sys 3 Economizer Solenoid Valve

VSD Logic Board

J6-1

Comp 1 Phase A+ IGBT Gating Signal

VSD Logic Board

J6-3

Comp 1 Phase B- IGBT Gating Signal

VSD Logic Board

J6-4

Comp 1 Phase C+ IGBT Gating Signal

VSD Logic Board

J6-10

Comp 1 Phase A- IGBT Gating Signal

VSD Logic Board

J6-11

Comp 1 Phase B+ IGBT Gating Signal

VSD Logic Board

J6-13

Comp 1 Phase C- IGBT Gating Signal

VSD Logic Board

J6-14

Comp1 Enable

VSD Logic Board

J7-1

Comp 3 Phase A+ IGBT Gating Signal

VSD Logic Board

J7-3

Comp 3 Phase B- IGBT Gating Signal

VSD Logic Board

J7-4

Comp 3 Phase C+ IGBT Gating Signal

VSD Logic Board

J7-10

Comp 3 Phase A- IGBT Gating Signal

VSD Logic Board

J7-11

Comp 3 Phase B+ IGBT Gating Signal

VSD Logic Board

J7-13

Comp 3 Phase C- IGBT Gating Signal

VSD Logic Board

J7-14

Comp 3 Enable

VSD Logic Board

J8-1

Comp 2 Phase A+ IGBT Gating Signal

VSD Logic Board

J8-3

Comp 2 Phase B- IGBT Gating Signal

VSD Logic Board

J8-4

Comp 2 Phase C+ IGBT Gating Signal

VSD Logic Board

J8-10

Comp 2 Phase A- IGBT Gating Signal

VSD Logic Board

J8-11

Comp 2 Phase B+ IGBT Gating Signal

VSD Logic Board

J8-13

Comp 2 Phase C- IGBT Gating Signal

VSD Logic Board

J8-14

Comp 2 Enable

VSD Logic Board

J9-1

Comp 4 Phase A+ IGBT Gating Signal

VSD Logic Board

J9-3

Comp 4 Phase B- IGBT Gating Signal

VSD Logic Board

J9-4

Comp 4 Phase C+ IGBT Gating Signal

VSD Logic Board

J9-10

Comp 4 Phase A- IGBT Gating Signal

VSD Logic Board

J9-11

Comp 4 Phase B+ IGBT Gating Signal

VSD Logic Board

J9-13

Comp 4 Phase C- IGBT Gating Signal

VSD Logic Board

J9-12

Comp 4 Enable

VSD Logic Board

J11-3

Pre-charge Enable 1

VSD Logic Board

J11-7

Pre-charge Enable 2

VSD Logic Board

J10-1 to J10-2

VSD Fan / Pump Run

VSD Logic Board

J10-3 to J10-4

VSD Fault Relay (to control panel)

JOHNSON CONTROLS

301

MICROPANEL
FORM 201.23-NM1 (910)

BACNET, MODBUS AND YORKTALK 2


COMMUNICATIONS
Data can be read and in some cases modified using a
serial communication BACnet, Modbus or YorkTalk 2
network connection. This information allows communications of chiller operating parameters and external
control changes to setpoint, load limiting, and start/
stop commands.

RS-232: connect to TB3 - Network (RX) to TB3


(TXD); Network (TX) to TB3 (RXD); Network
(GND) to TB3 (GND)

BACnet and YorkTalk 2 RS485 networks are wired to


the + and - terminals of TB1 for port 1 communications. Modbus network connection has the option of
RS232 or RS485 connection for port 2 communications. Modbus network is wired to either TB2 or TB3
as follows:
RS-485: connect to TB2 - Network (-1) to TB2 (-1);
Network (+1) to TB2 (+1)

In most cases, communication parameters will need


to be modified. TABLE 26 Values Required for
BAS Communication lists setup parameters for the
available protocols. Modification is accomplished by
pressing the PROGRAM, DOWN ARROW, DOWN
ARROW, DOWN ARROW, DOWN ARROW, and
ENTER keys in sequence. The list below shows the
displays for the values that may be modified:

Refer to FIG. 59 Control Board Connections for


TB1, and TB2 locations.

P2 PROTOCOL

DE MODIFIER ADDRESS

XXXXXXXXXX

XXXXX

P2 MANUAL MAC

DE MODIFIER OFFSET
XX

ADDRESS
P2 BAUD RATE

P1 PROTOCOL

XXXXX

XXXXXX
P2 PARITY

P1 MANUAL MAC
ADDRESS

XXX

XXXXX

XXX
P2 STOP BITS

P1 BAUD RATE

XXXXX
P2 HW SELECT BIT

P1 PARITY
XXXXX

XXXXX
REAL TIME ERROR

P1 STOP BITS
X

##

RESET 1 = YES, 0 = NO 0
Note: See TABLE 27 for error descriptions

302

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

The Chiller Control Board contains a dual UART for


RS-485 and RS-232 communications. UART1 is dedicated to RCC and ISN communications over an RS485 link. UART2 is dedicated to internal communications within the chiller. The RS-485 port is configured

LD10637

fig. 59 - CONTROL BOARD Connections

for 4800 baud, 1 start bit, 8 data bits, odd parity, and 1
stop bit. Connections for ISN communications are on
the Chiller Control Board on TB1/TB2. TB2 on the
Microgateway is utilized for ISN comms connection.
P3 is RS485+, P2 is RS485-, and USHL is the shield.

The table below shows the minimum, maximum, and default values.
table 25 minimum, maximum and default values
DESCRIPTION

MINIMUM

MAXIMUM

DEFAULT

DE MODIFIER ADDRESS

-1

41943

-1

DE MODIFIER OFFSET

-1

99

-1

P1 BAUD RATE

1200

76800

4800

1200, 4800, 9600, 19200, 38400, 76800, AUTO SELECTABLE


P2 BAUD RATE

1200

57600

1200

1200, 4800, 9600, 19200, 38400, 57600 SELECTABLE


P1, P2 MANUAL
Mac ADDRESS

-1

127

-1

P1, P2 PARITY

NONE

IGNORE

NONE

NONE, EVEN, ODD, IGNORE SELECTABLE


P1 PROTOCOL

BACNET

API

BACNET

MODBUS CLIENT

API

BACNET, API SELECTABLE


P2 PROTOCOL

TERMINAL

TERMINAL, MODBUS IO, MODBUS SERVER, API, MODBUS CLIENT SELECTABLE


P1, P2 STOP BITS

RESET REAL TIME ERROR

NO

YES

NO

JOHNSON CONTROLS

303

MICROPANEL
FORM 201.23-NM1 (910)

The table below shows set-up requirements for each communication protocol.
table 26 VALUES REQUIRED FOR BAS COMMUNICATION
Protocol

SETTING DESCRIPTION

BACnet MS/TP

DE MODIFIER ADDRESS

Modbus RTU5

YorkTalk 2

-1

DE MODIFIER OFFSET

0 to 99(4)

N/A

P1 PROTOCOL

BACNET

N/A

N/A

0 to 41943

P1 MANUAL MAC ADDRESS

(3)

N/A

N/A

P1 BAUD RATE

9600 To 76800 or Auto Selectable(1)

N/A

N/A

P1 PARITY

NONE

N/A

N/A
N/A

0-127

(1)

P1 STOP BITS

N/A

P2 PROTOCOL

N/A

MODBUS SVR

P2 MANUAL MAC ADDRESS

N/A

0-127

P2 BAUD RATE
P2 PARITY

(1)

N/A
N/A

N/A

19,200

(2)

N/A

N/A

NONE(2)

N/A

P2 STOP BITS

N/A

N/A

P2 HW SELECT BIT

N/A

RS-485 or RS-232(1)

N/A

RESET REAL TIME ERROR

N/A

N/A

N/A

P1 HW SELECT BIT

N/A

N/A

N/A

CHILLER ID

N/A

N/A

as Required By Network

or Other As Required By Network

number Is Multiplied By 100, Set As Required By Network

number Is Added To De Modifier Address, Set As Required By Network

unit Operating Software Version C.Mmc.13.03 Or Later Required For Modbus Protocol

Reboot required (cycle power) after settings are changed.

The table below shows the real time error numbers that
may be encountered during communication setup and
a description of each.

TABLE 27 REAL TIME ERROR NUMBERS


ERROR NUMBER (##)

304

DESCRIPTION

ALL OK

DATUM TYPE OK TEST FAILED

ENGLISH TEXT TOO LONG

FLOATING POINT EXCEPTION

GET PACKET FAILED

GET TYPE FAILED

INVALID UNIT CONVERSION

INVALID HARDWARE SELECTION

REAL TIME FAULT

SPANISH TEXT TOO LONG

10

THREAD EXITED

11

THREAD FAILED

12

THREAD STALLED

13

IO BOARD RESET

14

BRAM INVALID

15

BACNET SETUP FAILED


JOHNSON CONTROLS

FORM 201.23-NM1 (910)

BACnet and Modbus Communications

Communications Data Map Notes

Chiller data that can be read and modified using specific BACnet or Modbus Register Addresses; and the
data associated with the addresses, is outlined in the
following description:

(See TABLE 28)


1. IPU II based units are configured for Native BACnet
MS/TP and Modbus RTU communications.
Microgateway or E-Link not required for these two
communication protocols.
2. BACnet Object Types: 0= Analog In, 1 =
Analog Out, 2= Analog Value, 3= Binary In, 4 = Binary Output, 5= Binary Value,
8= Device, 15 = Alarm Notification (0 through 127
are reserved ASHRAE Objects).
3. WC= Inches of water column; CFM = Cubic Feet
per Minute; FPM = Feet per Minute: PSI = Lbs
per square inch; Pa = Pascals; kPa = Kilopascals;
PPM = Part per Million; kJ/kg = Kilojoules per
Kilogram.
4. Water Cooled Scroll units use the same firmware as
Air-Cooled Scroll units, ignoring Fan Control.

ANALOG WRITE POINTS


This data can be read and modified using a BACnet
or Modbus network connection. The Modbus Register
Address for these points is 1025 plus AV #.
BINARY WRITE POINTS
This data can be read and modified using a BACnet
or Modbus network connection. The Modbus Register
Address for these points is 1537 plus BV #.
ANALOG READ ONLY POINTS
This data can be read using a BACnet or Modbus network connection and can NOT be modified using this
connection. The Modbus Register Address for these
points is 513 plus AI #.
BINARY MONITOR ONLY POINTS
This data can be read using a BACnet or Modbus network connection and can NOT be modified using this
connection. The Modbus Register Address for these
points is 1281 plus BI #.
Refer to TABLE 28 for complete list of BACnet and
Modbus registers.

The latest data map information is


listed on the Johnson Controls Equipment Integration website.

JOHNSON CONTROLS

305

306
1030
1031

AV_5
AV_6
AV_7

JOHNSON CONTROLS

514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536

Mid Market Native Bacnet_Modbus

16
17
18
19
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
36
37
38
39
40

ANALOG READ ONLY POINTS


LCHLT
AI_1
RCHLT
AI_2
DAT
AI_3
S1_SUCT_TEMP
AI_4
OAT
AI_5
S1_SUCT_SHEAT
AI_6
S1_RUN_TIME
AI_7
S1_SUCT_PR
AI_8
S1_DSCH_PR
AI_9
S1_CIR_TEMP
AI_10
S1_DEF_TEMP
AI_11
S1_EEV_OUT
AI_12
S1_AR_TIMER
AI_13
AC_TIMER
AI_14
S2_SUCT_TEMP
AI_15
S2_RUN_TIME
AI_16
S2_SUCT_PR
AI_17
S2_DSCH_PR
AI_18
S2_CIR_TEMP
AI_19
S2_DEF_TEMP
AI_20
S2_SUCT_SH
AI_21
S2_AR_TIMER
AI_22
S2_EEV_OUT
AI_23

SS_SYS2

15

1539

1538
1540

BV_2

1032

BV_3

BV_1

SS_SYS1

12

BINARY WRITE POINTS


START_STOP

REM_SP_HEAT
HP_MODE

1026
1027
1028
1029

AV_1
AV_2
AV_3
AV_4

ANALOG WRITE POINTS


REM_SETP
SP_REM_SP_S1
LOAD_LIMIT
REM_CR
SP_REM_SP_S2

MODBUS
ADDRESS

BACnet
Object/Inst
ance

BACnet NAME

03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04

F
F
F
F
F
F
seconds
PSIG
PSIG
F
F
F
seconds
seconds
F
seconds
PSIG
PSIG
F
F
F
F
seconds

0, 1

0, 1

0, 1

F
index

F
PSIG
index
F
PSIG

SEE NOTE 5

ENG UNITS

Native

Check Sum

Comments

Board: 031-02630-xxx w/ 031-02550

R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R

R/W

R/W

R/W

R/W
R/W

R/W
R/W
R/W
R/W
R/W

READ
WRITE

Leaving Chilled Liquid Temp


Return Chilled Liquid Temp
Condensing Unit Models Only
Electronic Expansion Valve Models Only
Ambient Air Temperature
Sys 1 Suction Superheat ( EEV Models Only)
Sys 1 Run Time (seconds)
Sys 1 Suction Pressure
Sys 1 Discharge Pressure
Sys 1 Cooler Inlet Refrigerant Temp (R-407c Models Only)
Sys 1 Defrost Temperature (HP Only)
System 1 EEV Output % ( EEV Models Only)
Sys 1 Anti-Recycle Timer
Anti-Coincident Timer
System 2 Suction Temp ( EEVModels Only)
Sys 2 Run Time (seconds)
Sys 2 Suction Pressure
Sys 2 Discharge Pressure
Sys 2 Cooler Inlet Refrigerant Temperature(R-407c Only)
Sys 2 Defrost Temperature (HP Only)
Sys 2 Suction SuperHeat (EEV Models Only)
Sys 2 Anti-Recycle Timer
Sys 2 Suction Superheat ( EEV Models Only)

Sys 2 Start/Stop ( Suction Pressure (SP) Control Only)

Sys 1 Start/Stop ( Suction Pressure (SP) Control Only)

Stop Start Command

Heating Setpoint (HP Only), 999 = Auto (95F - 122F)


Mode (HP Only) (0=Panel, 1=Cooling, 2=Heating)

Setpoint Cooling
Setpoint(HP Only), 99 = Auto; (40F - 70F)
Sys 1 Setpoint (Suction Pressure Control units only)
Load Limit Stage (0, 1, 2)
Cooling Range (DAT Mode Only)
Sys 2 Setpoint (Suction Pressure Control)

SEE NOTE 1

POINT DESCRIPTION
1

Page 1 of 3

S=Standard; O = Optional; N = Not Available

Point List Code

Standard with Board: 031-02630-xxx w/ 031-02550


Basildon with Board: 031-02630-xxx w/ 031-02550
MMHP with Board: 031-02630-xxx w/ 031-02550
Basildon MMHP with Board: 031-02630-xxx w/ 031-02550
Standard Micro Board 031-02550-xxx . Fix native Modbus communications. Fix Caf Metric functionality (SCR-766)
MMHP with Board: 031-02630-xxx w/ 031-02550Fix native Modbus communications. Fix Caf Metric functionality (SCR-766)
Basildon MMHP with Board: 031-02630-xxx w/ 031-02550 Fix native Modbus communications. Fix Caf Metric functionality (SCR-766)

Modbus and BACnet MS/TP Data Maps

Property of JCI/York International. Subject to change without notice


Middle Market IPU II NATIVE BACnet _Modbus Data Maps_ Rev A_06.xls

01,03,05,15,06,
16
01,03,05,15,06,
16
01,03,05,15,06,

03,06,16
03,06,16
03,06,16
03,06,16
03,06,16
03,06,16
03,06,16

Type Supported

MODBUS Data

York PN
031-02755-001
031-02755-002
031-02755-003
031-02755-004
031-02755-001
031-02755-003
031-02755-004

Date
29-Nov-06
29-Nov-06
29-Nov-06
29-Nov-06
17-Oct-08
17-Oct-08
17-Oct-08

Version
C.MMC.13.00
C.MMC.15.00
C.MMC.14.00
C.MMC.16.00
C.MMC.13.02
C.MMC.14.02
C.MMC.16.02

13
14

10
11

4
5
6
7
8
9

1
3

ITEM REF
NUM

1
2
3
4
5
6
7
8
9
10

ITEM

YCAL/YCUL/YCWL/YLAA IPU II

2/25/2009

10

MICROPANEL
FORM 201.23-NM1 (910)

TABLE 28 - BACNET AND MODBUS COMMUNICATIONS DATA MAP

JOHNSON CONTROLS

307

1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300

AI_34
AI_35
AI_36
AI_37
AI_38
AI_39
AI_40
AI_41
AI_42
AI_43
AI_44
AI_45
AI_46
AI_47
AI_48
AI_49
AI_50
AI_51
AI_52
AI_53

AR_TIME
LCHLT_CUT
LOW_AMB_CUT
SUCT_P_CO_HT
L_SUCT_P_CO
H_DSCH_P_CO
COOL_SETP
SP_SETP_S1
CONTROL_RG
SP_CTL_RG_S1
SP_SETP_S2
HEAT_SETP
SP_CTL_RG_S2
HEAT_RANGE
S1_DSCH_TEMP
S1_DSCH_SHEAT
S2_DSCH_TEMP
S2_DSCH_SH
LEAVING_HOT

BINARY MONITOR ONLY POINTS


S1_ALARM
BI_1
S2_ALARM
BI_2
EVAP_HTR
BI_3
EVAP_PUMP
BI_4
S1_C1_RUN
BI_5
S2_C1_RUN
BI_6
S1_LLSV
BI_7
S1_MODE_SV
BI_8
S1_HGBV
BI_9
S1_BHS
BI_10
S1_C2_RUN
BI_11
S2_C2_RUN
BI_12
S2_LLSV
BI_13
S2_MODE_SV
BI_14
LEAD_SYS
BI_15
S1_C3_RUN
BI_16
S2_C3_RUN
BI_17
CH_LIQ_TYPE
BI_18
AMB_MODE
BI_19

RETURN_HOT

547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566

AI_33

CONTROL_MODE

546

545

537
538
539
540
541
542
543
544

MODBUS
ADDRESS

AI_32

BACnet
Object/Inst
ance
AI_24
AI_25
AI_26
AI_27
AI_28
AI_29
AI_30
AI_31

NUM_COMPS
S1_OP_CODE
S1_FLT_CODE
S2_OP_CODE
S2_FLT_CODE
S1_DBG_CODE
S1_FAN_STAGE
S2_DBG_CODE
S2_FAN_STAGE

BACnet NAME

Mid Market Native Bacnet_Modbus

74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93

50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72

49

41
42
43
44
45
46
47
48

ITEM REF
NUM

0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1
0, 1

seconds
F
F
PSIG
PSIG
PSIG
F
F
F
F
F
F
F
F
F
F
F
F
F
F

count

count

count
index
index
index
index
index
count
index

ENG UNITS

R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R

R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R

R
R
R
R
R
R
R
R

READ
WRITE

(0=Leaving Water, 1=Return Water, 2=Discharge Air, 3=Suction Press,

Sys 1 Alarm
Sys 2 Alarm
Evaporator Heater Status
Evaporator Pump Status
Sys 1 Comp 1 Run
Sys 2 Comp 1 Run
Sys 1 Liquid Line Solenoid Valve
Sys 1 Mode Solenoid Valve (HP Only)
Sys 1 Hot Gas Bypass Valve
Bivalent Heat Source (HP Only)
Sys 1 Comp 2 Run
Sys 2 Comp 2 Run
Sys 2 Liquid Line Solenoid Valve
Sys 2 Mode Solenoid Valve (HP Only)
Lead System (0 = Sys 1, 1 = Sys 2)
Sys 1 Comp 3 Run
Sys 2 Comp 3 Run
Chilled Liquid Type (0=Water, 1=Glycol)
Ambient Control Mode (0=Std Amb, 1=Low Amb)

Anti-Recycle Time (Programmed)


Leaving Chilled Liquid Temp Cutout
Low Ambient Temperature Cutout
Low Suction Pressure Cutout Heating (HP Only)
Low Suction Pressure Cutout (Cooling on HP units )
High Discharge Pressure Cutout
Setpoint
Setpoint 1 (SP Control)
Cooling Range
Cooling Range 1 (SP Control)
Setpoint 2 (SP Control)
Heating Setpoint (HP Only)
Cooling Range 2 (SP Control)
Heating Range (HP Only)
Sys 1 Discharge Temperature (EEV Only)
Sys 1 Discharge Superheat (EEV Only)
Sys 2 Discharge Temperature (EEV Only)
Sys 2 Discharge Superheat (EEV Only)
Leaving Liquid Hot Temp (R-410a)
Return Liquid Hot Temp (R-410a)

4=Cooling, 5=Heating)

Unit Control Mode

Number of Compressors
(See(Definition
Table A & B)
Sys 1 Operational Code
in Table 32)
(See(Definition
Table A & B)
Sys 1 Fault Code
in Table 32)
(See(Definition
Table A & B)
Sys 2 Operational Code
in Table 32)
Sys 2 Fault Code
in Table 32)
(See(Definition
Table A & B)
Sys 1 Debug Code
Sys 1 Condenser Fan Stage
Sys 2 Debug Code
Sys 2 Condenser Fan Stage

POINT DESCRIPTION

Property of JCI/York International. Subject to change without notice


Middle Market IPU II NATIVE BACnet _Modbus Data Maps_ Rev A_06.xls

01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03
01,02,03

03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04

03,04

03,04

03,04
03,04
03,04
03,04
03,04
03,04
03,04
03,04

Type Supported

MODBUS Data
1

Page 2 of 3

S=Standard; O = Optional; N = Not Available

Point List Code

2/25/2009

10

FORM 201.23-NM1 (910)

TABLE 28 - BACNET AND MODBUS COMMUNICATIONS DATA MAP (CONTD)

308

Operational Codes

BACnet
Object/Inst
ance
BI_20
BI_21
BI_22

14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

12
13

11

TABLE B
Code
0
1
2
3
4
5
6
7
8
9
10

1301
1302
1303

MODBUS
ADDRESS

0, 1
0, 1
0, 1

ENG UNITS

MP/HPCO Inhibit

Low Motor Current / MP / HPCO


Motor Current Unbalanced
Low Differential Oil Pressure
Ground Fault
MP/HPCO Fault
Low Evaporator Temperature
Incorrect Refrigerant Programmed
Power Failure, Manual Reset Required
Unit Motor Current
Low Superheat
Sensor Fault

High Discharge Temperature


Improper Phase Rotation

High Oil Temperature

R
R
R

READ
WRITE

Fault Codes
No Fault
VAC Under Voltage
Low Ambient Temperature
High Ambient Temperature
Low Leaving Chilled Liquid Temp
High Discharge Pressure
High Differential Oil Pressure
Low Suction Pressure
High Motor Current
LLSV Not On
Low Battery Warning

01,02,03
01,02,03
01,02,03

Type Supported

MODBUS Data
POINT DESCRIPTION
Local/Remote Control Mode (0=Local, 1=Remote)
Units (0=Imperial, 1=SI)
Lead/Lag Control Mode (0=Manual, 1=Auto)

Point List Code


2

Property of JCI/York International. Subject to change without notice


Middle Market IPU II NATIVE BACnet _Modbus Data Maps_ Rev A_06.xls

Page 3 of 3

S=Standard; O = Optional; N = Not Available

BACnet Object Types: 0= Analog In, 1 = Analog Out, 2= Analog Value, 3= Binary In, 4 = Binary Output, 5= Binary Value, 8= Device, 15 = Alarm Notification ( 0 -127 are reserved ASHRAE Objects)
WC= Inches of water column; CFM = Cubic Feer per Minute; FPM = Feet per Minute: PSI = Lbs per square inch; Pa = Pascals; kPa = Kilopascals; PPM = Part Per Million; kJ/kg = Kilojoules per Kilogram
See the applicable Middle Market Chiller Operations Manual for more details
The YCWL uses the same firmware as a YCAL , it just ignores Fan Control

The IPU II based YCAL /YCUL Units are configured for Native BACnet MS/TP and Modbus RTU communications. The Microgateway product is not required for these 2 interfaces

Note that these tables of FAULT and OPERATIONAL Codes are for all DX products.

Load Limiting
Compressor(s) Running

Suction Limiting
Discharge Limiting

Anti-Recycle Timer Active


Manual Override

Anti-Coincidence Timer Active

No Abnormal Condition
Unit Switch Off
System Switch Off
Lock-Out
Unit Fault
System Fault
Remote Shutdown
Daily Schedule Shutdown
No Run Permissive
No Cool Load

CNTL_MODE
DATA_UNIT
AUTO_LL

BACnet NAME

Mid Market Native Bacnet_Modbus

NOTES
1
2
3
4
5
6
7
8
9
10

NOTE:

14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

12
13

11

TABLE
Code
0
1
2
3
4
5
6
7
8
9
10

94
95
96

ITEM REF
NUM

2/25/2009

10

MICROPANEL
FORM 201.23-NM1 (910)

TABLE 28 - BACNET AND MODBUS COMMUNICATIONS DATA MAP (CONTD)

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Yorktalk 2 Communications
Received Data (Control Data)
The unit receives eight data values from the MicroGateway or E-Link. The first four are analog values and the
last four are digital values. These eight data values are
used as control parameters when in REMOTE mode.
When the unit is in LOCAL mode, these eight values
are ignored. If the unit receives no valid YorkTalk 2
transmission for 5 minutes it will revert back to all local control values. TABLE 29 Yorktalk 2 Communications Data Map lists the control parameters. These
values are found under feature 54 in the MicroGateway
or E-Link.

Transmitted Data
After receiving a valid transmission from the MicroGateway or E-Link, the unit will transmit either operational data or history buffer data depending on the
History Buffer Request on ENG PAGE 10. Data
must be transmitted for every page under feature 54. If
there is no value to be sent to a particular page, a zero
will be sent. TABLE 29 Yorktalk 2 Communications
Data Map shows the data values and page listings
for this unit.

The latest point map information is


listed on the Johnson Controls Equipment Integration website.

JOHNSON CONTROLS

309

Ref.

ASCII
PAGE
REF
P0 1
P0 2
P0 3
P0 4
P0 5
P0 6
P0 7
P0 8
P0 9
P1 0
P11
P1 2
P13
P1 4
P15
P1 6
P1 7
P1 8
P1 9
P20
P21
P2 2
P2 3
P24
P2 5
P2 6
P2 7
P28
P2 9
P30
P3 1
P32
P3 3
P3 4
P3 5
P3 6
P3 7
P3 8
P3 9
P4 0

Item
1
2
3
4
5
6
7
8
9
10

310

ENG
PAGE
REF
P0 3
P0 4
P0 5
P0 6
P0 7
P0 8
P0 9
P1 0
P1 1
P1 2
P13
P1 4
P15
P1 6
P17
P1 8
P1 9
P2 0
P2 1
P22
P23
P2 4
P2 5
P26
P2 7
P2 8
P2 9
P3 0
P3 1
P32
P3 3
P34
P3 5
P3 6
P3 7
P3 8
P3 9
P4 0
P4 1
P4 2

Date

YORK P N
031-02049-001
031-02049-001
031-02049-001
flash
flash
flash

Checksum
944D
964B
2226
xxxx
xxxx
xxxx

Baud
4800
4800
4800
4800
4800
4800

MicroGateway / ELINK

GPIC
Object
T ype

York Talk
Point
T ype
A. Control
A. Control
A. Control
A. Control
D. Control
D. Control
D. Control
D. Control
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor

ISN LINC
Descriptive
T ext

8 - 11
12 - 15
16 - 19
20 - 23
24 - 27
28 - 31
32 - 35
36 - 39
40 - 43
44 - 47
48 - 51
52 - 55
56 - 59
60 - 63
64 - 67
68 - 71
72 - 75
76 - 79
80 - 83
84 - 87
88 - 91
92 - 95
96 - 99
1 00 - 103
104 - 107
108
109
110
111
112
113
114

York Talk
Character
Position
ADF 1
ADF 2
ADF 3
ADF 4
BD 1
BD 2
BD 3
BD 4
ADF 5
ADF 6
ADF 7
ADF 8
ADF 9
ADF 10
ADF 11
ADF 12
ADF 13
ADF 14
ADF 15
ADF 16
ADF 17
ADF 18
ADF 19
ADF 20
ADF 21
ADF 22
ADF 23
ADF 24
ADF 25
ADF 26
ADF 27
ADF 28
ADF 29
BD 5
BD 6
BD 7
BD 8
BD 9
BD 1 0
BD 1 1

N2
Address

S
S
S
O
S
O
S
O
S
S
S
S
O
S
S
O
S
S
S
S
O
O
S
O
S
S
S
S
S
S
S
S

Sys 1 EEV Output % (EEV only)


Sys 1 Anti- Recycle Timer
Anti-Coincident Timer
Sys Suction Temp ( EEV only)
Sys 2 Run Time (seconds)
Sys 2 Suction Pressure
Sys 2 Discharge Pressure
Sys 2 Cooler Inlet Refrigerant Temperature (R-407c systems Only)
Sys 2 Defrost Temperature ( HP only)
Sys 2 Suction Superheat (EEV only)
Sys 2 Anti-Recycle Timer
Sys 2 EEV Output % (EEV only)
Number of Compressors
Sys 1 Alarm
Sys 2 Alarm
Evaporator Heater Status
Evaporator Pump Status
Sys 1 Compressor 1 Run
Sys 2 Compressor 1 Run
Sys 1 Liquid Line Solenoid Valve

O
S
S
O
S
S
S
S
O
O
S
O
S
S
S
S
S
S
S
S

S
S
S
O
S
O
S
O
S
S
S
S

O
S
S
O
S
S
S
S
O
O
S
O
S
S
S
S
S
S
S
S

S
S
S
O
S
O
S
O
S
S
S
S

O
S
S
O
S
S
S
S
O
O
S
O
S
S
S
S
S
S
S
S

S
S
S
O
S
O
S
O
S
S
S
S

O
S
S
O
S
S
S
S
O
O
S
O
S
S
S
S
S
S
S
S

S
S
S
O
S
O
S
O
S
S
S
S

N = NOT AVAILABLE
1 2 3 4 5 6 7 8 9 10
S S S S S
S S S S S
O O O O O
O O O O O
S S S S S

History Buffer Request


Leaving Chilled Liquid Temp
Return Chilled Liquid Temp
Leaving Hot Liquid Temp (R-410a) Heat Mode Only
Discharge Air Temp ( Cond Unit) Return Hot Liquid Temp (410a- Heat Mod
Leaving Liquid Temp Hot (R-410a)
Ambient Air Temperature
Sys 1 Suction Superheat ( EEV only)
Sys 1 Run Time (seconds)
Sys 1 Suction Pressure
Sys 1 Discharge Pressure
Sys 1 Cooler Inlet Refrigerant Temperature(R-407c Only)

POINT LIST CODE:


S = STANDARD
O = OPTIONAL
POINT LIST DESCRIPT ION
Setpoint
Load Limit Stage (0, 1, 2)
Heating Setpoint (HP and YCW L HP)
Mode (HP and YCW L HP only) (0=Panel, 1= Cooling, 2 = Heating)
Start/Stop Command

ENG
PAGE
REF
P0 3
P0 4
P0 5
P0 6
P0 7
P08
P09
P1 0
P11
P12
P13
P1 4
P15
P1 6
P17
P1 8
P1 9
P2 0
P2 1
P22
P23
P2 4
P2 5
P26
P2 7
P2 8
P2 9
P3 0
P3 1
P32
P3 3
P34
P3 5
P3 6
P3 7
P3 8
P3 9
P4 0
P4 1
P4 2

Micro Board: 031-02050/02550

COM M ENT S
YCAL Micro Board 031-02050-xxx
YCAL Micro Board 031-02050-xxx
YCAL Micro Board 031-02050-xxx
YCAL Micro Board 031-02550-xxx, IPU 2 board.
YCWL ( water cooled version) Micro Board 031-02550-xxx, IPU 2 board.
Micro Board 031-02550-xxx . Fix native Modbus communications (SCR . Fix Caf Metric functionality (SCR-766)

York Talk 2

Use ASCII page column for interfaces utilizing an ASCII XL Translator or MicroGateway to communicate to a chiller LINC

Version
C.MMC.03.02
C.MMC.03.01
C.MMC.03.00
C.MMC.13.xx
C.MMC.13.xx
C.MMC.13.02

YCAL/YCWL/YLAA Middle Market w/ 2050, 2550

MICROPANEL
FORM 201.23-NM1 (910)

TABLE 29 - YorkTalk 2 COMMUNICATIONS DATA MAP

JOHNSON CONTROLS

ENG
PAGE
REF
P43
P4 4
P4 5
P4 6
P4 7
P4 8
P4 9
P5 0
P5 1
P5 2
P5 3
P5 4
P5 5
P5 6
P5 7
P5 8
P5 9
P60
P6 1
P62
P6 3
P64
P65
P6 6
P6 7
P6 8
P6 9
P7 0
P7 1
P7 2
P7 3
P7 4
P7 5
P76
P77
P78
P79
P80
P81
P82
P83
P84

ASCII
PAGE
REF
P41
P4 2
P4 3
P4 4
P4 5
P4 6
P4 7
P4 8
P4 9
P5 0
P5 1
P5 2
P5 3
P5 4
P5 5
P5 6
P5 7
P58
P5 9
P60
P6 1
P62
P63
P6 4
P6 5
P6 6
P6 7
P6 8
P6 9
P7 0
P7 1
P7 2
P7 3
P74
P75
P76
P77
P78
P79
P80
P81
P82

GPIC
Object
T ype

York Talk
Point
T ype
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
Code Monitor
Code Monitor
Code Monitor
Code Monitor
Code Monitor
Code Monitor
Code Monitor
Code Monitor
Code Monitor
Code Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
A. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor
D. Monitor

ISN LINC
Descriptive
T ext

York Talk
Character
Position
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138 - 141
142 - 145
146 - 149
150 - 153
154 - 157
158 - 161
162 - 165
166 - 169
170 - 173
174 - 177
178 - 181
182 - 185
186 - 189
190 - 193
194
195
196
197
198
BD 12
BD 1 3
BD 1 4
BD 1 5
BD 1 6
BD 1 7
BD 1 8
BD 1 9
BD 2 0
BD 2 1
BD 2 2
BD 2 3
BD 2 4
ADI 1
ADI 2
ADI 3
ADI 4
ADI 5
ADI 6
ADI 7
ADI 8
ADI 9
ADI 10
ADF 30
ADF 31
ADF 32
ADF 33
ADF 34
ADF 35
ADF 36
ADF 37
ADF 38
ADF 39
ADF 40
ADF 41
ADF 42
ADF 43
BD 25
BD 26
BD 27
BD 28
BD 29

N2
Address

JOHNSON CONTROLS
S
S
S
S
S
S
S
S
S
O
O
O
O
O
O

S
S
S
S
S
S
S
S
S
O
O
O
O
O
O

S
S
S
S
S
S
S
S
S
O
O
O
O
O
O

NOTE: The Appropriate Product Code Listing Summary Should Accompany Document

S
S
S
S
S
S
S
S
S
O
O
O
O
O
O

N = NOT AVAILABLE
1 2 3 4 5 6 7 8 9 10
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S N
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S
S S S S S

Unit Control Mode (0=Lv W tr, 1=Ret W tr, 2=Dis Air, 3=SP, 4=Cool, 5=Heat) S
Anti-Recycle Time (Programmed)
S
Leaving Chilled Liquid Temp Cutout
S
Low Ambient Temperature Cutout
S
Low Suction Pressure Cutout (Heating HP Only)
S
Low Suction Pressure Cutout (Cooling HP only)
S
High Discharge Pressure Cutout
S
Setpoint (local)
S
Cooling Range
S
Setpoint 2 ( SP Control), Heating Setpoint ( HP and YCW L HP only)
O
Cool Range Setpoint 2 (SP Control), Heat Range (HP and YCW L HP only) O
Sys 1 Discharge Temp (EEV only)
O
Sys 1 Discharge Superheat (EEV only)
O
Sys 2 Discharge Temp (EEV only)
O
Sys 2 Discharge Superheat (EEV only)
O

Sys 2 Condenser Fan Stage

Sys 1 Condenser Fan Stage

POINT LIST CODE:


S = STANDARD
O = OPTIONAL
POINT LIST DESCRIPT ION
Sys 1 Hot Gas Bypass Valve
Sys 1 Compressor 2 Run
Sys 2 Compressor 2 Run
Sys 2 Liquid Line Solenoid Valve
Lead System (0 = Sys 1, 1 = Sys 2)
Sys 1 Compressor 3 Run
Sys 2 Compressor 3 Run
Chilled Liquid Type (0=W ater, 1=Glycol)
Ambient Control Mode (0=Std Amb, 1=Low Amb)
Local/Remote Control Mode (0=Local, 1=Remote)
Units (0=Imperial, 1=SI)
Lead/Lag Control Mode (0=Manual, 1=Auto)
Sys 2 Hot Gas Bypass Valve
*Sys 1 Operational Code
*Sys 1 Fault Code
*Sys 2 Operational Code
*Sys 2 Fault Code

ENG
PAGE
REF
P43
P4 4
P4 5
P4 6
P4 7
P4 8
P4 9
P50
P5 1
P5 2
P5 3
P5 4
P5 5
P5 6
P5 7
P5 8
P5 9
P60
P6 1
P62
P6 3
P64
P65
P6 6
P67
P6 8
P6 9
P7 0
P7 1
P7 2
P7 3
P7 4
P7 5
P76
P77
P78
P79
P80
P81
P82
P83
P84

FORM 201.23-NM1 (910)

TABLE 29 - YORKTALK 2 COMMUNICATIONS DATA MAP (CONTD)

311

ENG
PAGE
P56
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

ASCII
PAGE
P54
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

312

C_OPER.CODE
No Abnormal Condition
Unit Switch Off
System Switch Off
Lock-Out
Unit Fault
System Fault
Remote Shutdown
Daily Schedule Shutdown
No Run Permissive
No Cool Load
Anti-Coincidence Timer Active
Anti-Recycle Timer Active
Manual Override
Suction Limiting
Discharge Limiting
n /a
Load Limiting
Compressor(s) Running
Heat Pump Load Limiting ( HP Only)

Operational Code

ENG
PAGE
P57
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

ASCII
PAGE
P55
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
C_FAULT .CODE
No Fault Code
n /a
Low Ambient Temperature
n /a
Low Leaving Chilled Liquid Temperature
High Discharge Pressure
n /a
Low Suction Pressure
n /a
n /a
n /a
n /a
n /a
n /a
n /a
n /a
n /a
n /a
MP / HPCO Fault
Low Evaporator Temperature
n/a
n/a
Unit Motor Current
Low Superheat
Sensor Fault
Discharge Inhibit
MP/HPCO Inhibit
Pump Trip
Pump Fail Make Flow

Fault Code

MICROPANEL
FORM 201.23-NM1 (910)

TABLE 29 - YORKTALK 2 COMMUNICATIONS DATA MAP (CONTD)

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Section 9 - maintenance
General Requirements

Refrigerant Leaks

The units have been designed to operate continuously,


provided they are regularly maintained and operated
within the limitations given in this manual. Each unit
should be included in a routine schedule of daily maintenance checks by the operator/customer, backed up by
regular service inspection and maintenance visits by a
suitably qualified Service Engineer.

Visually check the heat exchangers, compressors and


pipework for damage and gas leaks.

It is entirely the responsibility of the owner to provide for these regular maintenance requirements and/
or enter into a maintenance agreement with a Johnson
Controls service organization to protect the operation
of the unit. If damage or a system failure occurs due
to improper maintenance during the warranty period,
Johnson Controls shall not be liable for costs incurred
to return the unit to satisfactory condition.

Compressor Oil Level

This Maintenance section applies


to the basic unit only and may, on
individual contracts, be supplemented
by additional requirements to cover
any modifications or ancillary equipment as applicable.
The Safety section of this manual
should be read carefully before attempting any maintenance operations
on the unit.

Daily Maintenance
The following maintenance checks should be carried
out on a daily basis by the operator/customer. Please
note that the units are not generally user serviceable
and no attempt should be made to rectify faults or
problems found during daily checks unless competent
and equipped to do so. If in any doubt, contact your local Johnson Controls Service Agent.

Operating Conditions
Read the operating pressures and temperatures at the
control panel using the display keys and check that
these are within the operating limitations given in the
manual.
Check the compressor oil level after the compressor
has been operating on FULL LOAD for approximately half an hour. The oil level should be between the
upper and lower sight glasses on the oil separators.
Refrigerant Charge
When a system starts up, or sometimes after a change
of capacity, a flow of bubbles will be seen in the liquid
line sight glass. After a few minutes of stable operation,
the bubbles should clear leaving just liquid refrigerant
showing in the sight glass.
Scheduled Maintenance
The maintenance operations detailed in the following
table should be carried out on a regular basis by a suitably qualified Service Engineer. It should be noted that
the interval necessary between each minor and major service can vary depending on, for instance, application, site conditions and expected operating schedule. Normally a minor service should be carried out
every three to six months and a major service once a
year. It is recommended that your local Johnson Controls Service Center is contacted for recommendations
for individual sites.
Chiller / Compressor Operating Log
A Chiller/Compressor Operating Log is supplied on
Page 329 for logging compressor and chiller operating
data.

Unit Status
Press the STATUS key on the keypad and ensure no
fault messages are displayed.

JOHNSON CONTROLS

313

MAINTENANCE

FORM 201.23-NM1 (910)

R-134a conversion tables


The following table can be used for converting R-134A pressures to their equivalent saturated temperatures.
TABLE 30 - R-134a pressure to saturated temperature conversion

314

PRESSURE

DEW POINT

PRESSURE

DEW POINT

PRESSURE

DEW POINT

PSIG (BAR)

TEMP. F (C)

PSIG (BAR)

TEMP. F (C)

PSIG (BAR)

TEMP. F (C)

0.0 (0)

-14.9 (-26.1)

135.0 (9.31)

105.0 (40.6)

270.0 (18.62)

152.0 (66.7)

5.0 (.34)

-3.0 (-19.4)

140.0 (9.65)

107.2 (41.8)

275.0 (18.96)

153.4 (67.4)

10.0 (.69)

6.7 (-14.1)

145.0 (10.0)

109.4 (43)

280.0 (19.31)

154.7 (68.2)

15.0 (1.03)

14.9 (-9.5)

150.0 (10.34)

111.5 (44.2)

285.0 (19.65)

156.1 (68.9)

20.0 (1.38)

22.2 (-5.4)

155.0 (10.69)

113.6 (45.3)

290.0 (19.99)

157.4 (69.7)

25.0 (1.72)

28.7 (-1.8)

160.0 (11.03)

115.6 (46.4)

295.0 (20.34)

158.7 (70.4)

30.0 (2.07)

34.6 (1.4)

165.0 (11.38)

117.6 (47.6)

300.0 (20.68)

160.0 (71.1)

35.0 (2.41)

40.0 (4.4)

170.0 (11.72)

119.6 (48.7)

305.0 (21.03)

161.3 (71.8)

40.0 (2.76)

45.0 (7.2)

175.0 (12.07)

121.5 (49.7)

310.0 (21.37)

162.5 (72.5)

45.0 (3.10)

49.6 (9.8)

180.0 (12.41)

123.3 (50.7)

315.0 (21.72)

163.8 (73.2)

50.0 (3.45)

54.0 (12.2)

185.0 (12.76)

125.2 (51.8)

320.0 (22.06)

165.0 (73.9)

55.0 (3.79)

58.1 (14.5)

190.0 (13.10)

126.9 (52.7)

325.0 (22.41)

166.2 (74.6)

60.0 (4.14)

62.0 (16.7)

195.0 (13.44)

128.7 (53.7)

330.0 (22.75)

167.4 (75.2)

65.0 (4.48)

65.7 (18.7)

200.0 (13.79)

130.4 (54.7)

335.0 (23.10)

168.6 (75.9)

70.0 (4.83)

69.2 (20.7)

205.0 (14.13)

132.1 (55.6)

340.0 (23.44)

169.8 (76.6)

75.0 (5.17)

72.6 (22.6)

210.0 (14.48)

133.8 (56.6)

345.0 (23.79)

171.0 (77.2)

80.0 (5.52)

75.9 (24.4)

215.0 (14.82)

135.5 (57.5)

350.0 (24.13)

172.1 (77.8)

85.0 (5.86)

79.0 (26.1)

220.0 (15.17)

137.1 (58.4)

355.0 (24.48)

173.3 (78.5)

90.0 (6.21)

82.0 (27.8)

225.0 (15.51)

138.7 (59.3)

360.0 (24.82)

174.4 (79.1)

95.0 (6.55)

84.9 (29.4)

230.0 (15.86)

140.2 (60.1)

365.0 (25.17)

175.5 (79.7)

100.0 (6.89)

87.7 (30.9)

235.0 (16.20)

141.8 (61)

370.0 (25.51)

176.6 (80.3)

105.0 (7.24)

90.4 (32.4)

240.0 (16.55)

143.3 (61.8)

375.0 (25.86)

177.7 (80.9)

110.0 (7.58)

93.0 (33.9)

245.0 (16.89)

144.8 (62.3)

380.0 (26.20)

178.8 (81.6)

115.0 (7.93)

95.5 (35.3)

250.0 (17.24)

146.3 (63.5)

385.0 (26.54)

179.9 (82.2)

120.0 (8.27)

98.0 (36.7)

255.0 (17.58)

147.7 (64.3)

390.0 (26.89)

180.9 (82.7)

125.0 (8.62)

100.4 (38)

260.0 (17.93)

149.2 (65.1)

395.0 (27.23)

182.0 (83.3)

130.0 (8.96)

102.7 (39.3)

265.0 (18.27)

150.6 (65.9)

400.0 (27.58)

183.0 (83.9)

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

maintenance requirements
for yciv chillers

PROCEDURE

WEEKLY

Check Oil Level in Oil Separator Sight


Glass.

Check Liquid Line Sight Glass/ Moisture


Indicator.

Record System Operating Temperatures &


Pressures.

Check Condenser Coils for dirt / debris


and clean as necessary.

QUARTERLY

Check Programmable Operating Setpoints


and Safety Cutouts. Assure they are correct for the application.

Check Compressor and Evaporator Heater operation.

SEMIANNUALLY

ANNUALLY

EVERY 5

EVERY *

YEARS

HOURS

9
Check for dirt in the Panel. Check Door
Gasket sealing integrity.

**Check Superheat on the Evaporator and


the Economizer feed to the Compressor.

**Check Condenser Subcooling.

**Leak check the Chiller.

**Sample Compressor Oil, check for Acid,


and replace if necessary.

**Disconnect Power Source and Lock


Out. Check tightness of Power Wiring
connections.

Check Glycol concentration on Low Temp.


or other applications where freezing may
be a problem.

VSD Glycol Change.

* Reserved for customer use for any special site requirements.


**T h i s p r o c e d u r e m u s t b e p e r f o r m e d a t t h e s p e c i f i c t i m e b y a n i n d u s t r y c e r t i f i e d t e c h n i c i a n w h o h a s b e e n
trained and qualified to work on this type of equipment. A record of this procedure be successfully carried out should be maintained on file
by the equipment owner should proof of adequate maintenance be required at a later date for warranty purposes.

JOHNSON CONTROLS

315

MAINTENANCE

FORM 201.23-NM1 (910)

troubleshooting guide

(Always remove power to the chiller and assure the DC Bus voltage has bled off)
PROBLEM

POSSIBLE CAUSE

Supply to the Panel


is missing.
No Display on Control Panel.
Unit will NOT Run.

Line Fuse Blows.

Chiller Fault:
LOW AMBIENT
TEMPERATURE

Check Fuses.

Chiller Control Board is defective.

Replace Chiller Control Board

Display Board defective.

Replace Display Board

SCR Diode Module is defective.

Check SCR/Diode Module.

IBGT Module is defective.

Check IBGT Module.

VSD Logic Board is defective.

Replace VSD Logic Board.

SCR Trigger Board is defective

Replace SCR Trigger Board.

Ambient temperature is lower than


the programmed operating limit.

Check the programmed cutout and


determine if it is
programmed correctly

Ambient Temperature
is above the maximum
operating limit.

Leaving chilled liquid temperature


drops faster than the
unit can unload.

System Fault:
HIGH OIL
TEMPERATURE

316

Check the panel against the


thermometer reading of
ambient temperature
Check outside air temperature.
Check the Panel Display against
Thermometer reading of
Ambient Temperature at the sensor.
Check for restricted flow.
Check for rapid flow changes.
Water loop is too small.
Flow is below minimum for chiller.
Check Sensor against
Temp. Gauge in water line.

Chilled Water Sensor


is defective.
System Fault:
CONTROL VOLTAGE

Check 1FU, 2FU, 4FU, 5FU


17FU, or 19FU.

Line Fuse is blown.

Ambient Sensor is defective.

Chiller Fault:
LOW LEAVING
CHILLED LIQUID

High Voltage to the


Chiller is missing.

Check 2T or 10T Transformer.

Ambient Sensor is defective.

Chiller Fault:
HIGH AMBIENT
TEMPERATURE

ACTION

Check Sensor for


intermittent operation.
Check Wiring for shorts or opens.

System Fuse is blown.

Check respective system


Fuse 20FU or 21FU.

Oil Temperature
Sensor is defective.

Check Sensor with infrared to


determine if reading is reasonable.

Condenser Fans NOT


operating or running backwards.

Check Fans.

Coils dirty.

Check and clean Coils.

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

troubleshooting guide (CONT'D)

(Always remove power to the chiller and assure the DC Bus voltage has bled off)
PROBLEM

System Fault:
HIGH
DISCHARGE
PRESSURE

System Fault:
HIGH
DISCHARGE
TEMPERATURE

POSSIBLE CAUSE

ACTION

Coils dirty.

Check and clean coils.

Coils are damaged.

Comb out fins.


Check fan fuses.

Fans NOT operating.

Check fan rotation.


Check fan motor/blade.

System is overcharged.

Remove charge and check subcooling.

Discharge Temperature
Sensor is defective.

Check Sensor.

Condenser Fans NOT operating


or are running backwards.

Check Fans.

Coils dirty.

Check and clean Coils.

High Superheat.

Measure Superheat with gauges and


thermocouple. Determine cause.
Refrigerant charge low.
Check subcooling.

System Fault:
HIGH MOTOR
TEMPERATURE

Excess charge in system,


High discharge pressure.
Check subcooling.
High Motor temperature
input from one of the sensors

High Superheat. Drain/Feed Valves


NOT controlling. Isolate cause.
Motor Sensor reading incorrectly.
Program panel to ignore
a single sensor.
Economizer Solenoid energized at
low speeds. Valve is leaking through.

System Fault:
LOW
SUCTION
PRESSURE

System Fault:
DISCHARGE
PRESSURE
LIMITING

JOHNSON CONTROLS

Low charge.

Check subcooling.

Transducer reads incorrectly.

Check transducer against a gauge.

Suction Temp. Sensor


reads incorrectly.

Check sensor against


a thermocouple.

Low flow.

Check flow.

Feed or Drain Valve NOT operating

Check Feed and Drain Valve


operation.
Check superheat.

Feed or Drain Valve defective.

Check Feed and Drain Valve


operation.
Check superheat.

Discharge Transducer is defective.

Check transducer against a gauge.

Ambient Temp. very high.

Normal operation.

Fans NOT operating.

Check fan operation.

Remote or local discharge pressure


load limiting is programmed.

Normal operation.

317

MAINTENANCE

FORM 201.23-NM1 (910)

troubleshooting guide (CONT'D)

(Always remove power to the chiller and assure the DC Bus voltage has bled off)
PROBLEM

POSSIBLE CAUSE

ACTION
Ambient temperature is high,
normal response from controller

System Fault:
MOTOR
CURRENT
LIMITING

High motor current


has activated
current limiting

Remote or panel limiting is in


effect, Normal response.
Excess charge in system,
adjust charge.
Condenser coils dirty,
Clean condenser.
Fans NOT operating,
Check fans.

VSD Fault:
High
Baseplate
Temperature
VSD Fault:
Low DC
Bus Voltage

Coolant level low.

Add coolant.

Glycol Pump is defective.

Replace Glycol Pump.

VSD Board is defective

Replace VSD Logic Board.

IBGT Module is defective.

Check defective IGBT Module.

SCR / Diode Module


is defective.

Check SCR / Diode Module.

SCR Trigger Board is defective.

Check SCR Trigger Board.

Evacuating A System
If a system or a portion of a system needs to be evacuated, it should be evacuated to a minimum of 500
microns. The system should then be able to hold the
vacuum for 10 minutes with a maximum rise of 50 microns. If the system is not able to hold a vacuum, recheck the system for leaks.

318

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

limited warranty
Warranty on New Equipment
Johnson Controls warrants all equipment and associated factory supplied materials, or start-up services performed by Johnson Controls in connection therewith,
against defects in workmanship and material for a period of eighteen (18) months from date of shipment.
Subject to the exclusions listed below, Johnson Controls, at its option, will repair or replace, FOB point of
shipment, such YORK products or components as it
finds defective.
Exclusions - Unless specifically agreed to in the contract documents, this warranty does not include the following costs and expenses:
1. Labor to remove or reinstall any equipment, materials, or components.
2. Shipping, handling, or transportation charges.
3. Cost of refrigerants.
No warranty repairs or replacements will be made until
payment for all equipment, materials, or components
has been received by Johnson Controls.
Warranty on Reconditioned or Replacement
Materials
Except for reciprocating compressors, which Johnson
Controls warrants for a period of one year from date of
shipment, Johnson Controls warrants reconditioned or
replacement materials, or start-up services performed
by Johnson Controls in connection therewith, against
defects in workmanship or material for a period of
ninety (90) days from date of shipment. Subject to the
exclusions listed below, Johnson Controls, at its option,
will repair or replace, FOB point of shipment, such
materials or parts as Johnson Controls finds defective.
However, where reconditioned or replacement materials or parts are placed on equipment still under the
original new equipment warranty, then such reconditioned or replacement parts are warranted only until the
expiration of such original new equipment warranty.
Exclusions - Unless specifically agreed to in the contract documents, this warranty does not include the following costs and expenses:
1. Labor to remove or reinstall any equipment, materials, or components.
2. Shipping, handling, or transportation charges.
3. Cost of refrigerant.

JOHNSON CONTROLS

No warranty repairs or replacements will be made until


payment for all equipment, materials, or components
has been received by Johnson Controls.
All Warranties and Guarantees Are Void If:
1. Equipment is used with refrigerants, oil, or antifreeze agents other than those authorized by Johnson
Controls.
2. Equipment is used with any material or any equipment such as evaporators, tubing, other low side
equipment, or refrigerant controls not approved by
Johnson Controls.
3. Equipment has been damaged by freezing because
it is not properly protected during cold weather, or
damaged by fire or any other conditions not ordinarily encountered.
4. Equipment is not installed, operated, maintained and
serviced in accordance with instructions issued by
Johnson Controls.
5. Equipment is damaged due to dirt, air, moisture, or
other foreign matter entering the refrigerant system.
6. Equipment is not properly stored, protected or inspected by the customer during the period from date
of shipment to date of initial start.
7. Equipment is damaged due to acts of god, abuse,
neglect, sabotage, or acts of terrorism.
THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES AND LIABILITIES, EXPRESS OR
IMPLIED IN LAW OR IN FACT, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE
WARRANTIES CONTAINED HEREIN SET FORTH
BUYERS SOLE AND EXCLUSIVE REMEDY IN
THE EVENT OF A DEFECT IN WORKMANSHIP
OR MATERIALS. IN NO EVENT SHALL JOHNSON CONTROLS LIABILITY FOR DIRECT OR
COMPENSATORY DAMAGES EXCEED THE
PAYMENTS RECEIVED BY JOHNSON CONTROLS FROM BUYER FOR THE MATERIALS OR
EQUIPMENT INVOLVED. NOR SHALL JOHNSON
CONTROLS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
THESE LIMITATIONS ON LIABILITY AND DAMAGES SHALL APPLY UNDER ALL THEORIES OF
LIABILITY OR CAUSES OF ACTION, INCLUDING, BUT NOT LIMITED TO, CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE) OR
STRICT LIABILITY. THE ABOVE LIMITATIONS
SHALL INURE TO THE BENEFIT OF JOHNSON
CONTROLS SUPPLIERS AND SUBCONTRACTORS.

319

MAINTENANCE

FORM 201.23-NM1 (910)

chilled liquid and suction temperature


sensor input voltage

TABLE 31 - temperature input voltage sensor (measured signal to SHIELD AT THE SENSOR)

320

TEMP. (F)

VOLTAGE

TEMP. (F)

VOLTAGE

TEMP. (F)

VOLTAGE

16.1

1.52

35.9

2.19

55.6

2.85

16.7

1.54

36.5

2.21

56.3

2.87

17.3

1.56

37.0

2.23

56.9

2.89

17.9

1.58

37.6

2.25

57.5

2.91

18.5

1.60

38.2

2.27

58.1

2.93

19.1

1.62

38.7

2.29

58.7

2.95

19.7

1.64

39.3

2.30

59.4

2.97

20.3

1.66

39.9

2.32

60.0

2.99

20.9

1.68

40.4

2.34

60.6

3.01

21.5

1.70

41.0

2.36

61.3

3.03

22.1

1.72

41.6

2.38

61.9

3.05

22.7

1.74

42.1

2.40

62.5

3.07

23.3

1.76

42.7

2.42

63.2

3.09

23.9

1.78

43.3

2.44

63.8

3.11

24.5

1.80

43.9

2.46

64.5

3.13

25.0

1.82

44.4

2.48

65.1

3.14

25.6

1.84

45.0

2.50

65.8

3.16

26.2

1.86

45.6

2.52

66.5

3.18

26.8

1.88

46.2

2.54

67.1

3.20

27.3

1.90

46.7

2.56

67.8

3.22

27.9

1.91

47.3

2.58

68.5

3.24

28.5

1.93

47.9

2.60

69.2

3.26

29.0

1.95

48.5

2.62

69.9

3.28

29.6

1.97

49.1

2.64

70.6

3.30

30.2

1.99

49.7

2.66

71.3

3.32

30.8

2.01

50.3

2.68

72.0

3.34

31.3

2.03

50.8

2.70

72.7

3.36

31.9

2.05

51.4

2.71

73.4

3.38

32.5

2.07

52.0

2.73

74.2

3.40

33.0

2.09

52.6

2.75

74.9

3.42

33.6

2.11

53.2

2.77

34.2

2.13

53.8

2.79

34.8

2.15

54.5

2.81

35.3

2.17

55.0

2.83
JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE 32 - outside air temperature sensor input voltage


(measured signal to SHIELD AT THE SENSOR)
TEMP. (F)

VOLTAGE

TEMP. (F)

VOLTAGE

TEMP. (F)

VOLTAGE

0.24

0.68

49.8

2.00

93.3

3.31

1.79

0.71

50.7

2.03

94.4

3.34

3.30

0.74

51.6

2.06

65.6

3.37

4.76

0.77

52.5

2.09

96.8

3.40

6.19

0.80

53.4

2.11

98.0

3.43

7.58

0.83

54.3

2.14

99.2

3.46

8.94

0.85

55.3

2.17

100.4

3.49

10.3

0.88

56.2

2.20

101.6

3.52

11.6

0.91

57.1

2.23

102.9

3.55

12.8

0.94

58.0

2.26

104.2

3.57

14.1

0.97

58.9

2.29

105.5

3.60

15.3

1.00

59.8

2.32

106.8

3.63

16.5

1.03

60.7

2.35

108.1

3.66

17.7

1.06

61.6

2.38

109.5

3.69

18.9

1.09

62.6

2.41

110.9

3.72

20.0

1.12

63.5

2.44

112.3

3.75

21.2

1.15

64.4

2.47

113.8

3.78

22.3

1.18

65.3

2.50

115.2

3.81

23.4

1.21

66.3

2.52

116.7

3.84

24.4

1.24

67.2

2.55

118.3

3.87

25.5

1.26

68.1

2.58

119.9

3.90

26.6

1.26

69.1

2.61

121.5

3.93

27.6

1.32

70.0

2.64

123.2

3.96

28.7

1.35

70.9

2.67

124.9

3.98

29.7

1.38

71.9

2.70

126.6

4.01

30.7

1.41

72.8

2.73

128.4

4.04

31.7

1.44

73.8

2.76

130.3

4.07

32.7

1.47

74.8

2.76

33.7

1.50

75.8

2.82

34.7

1.53

76.7

2.85

35.7

1.56

77.7

2.88

36.7

1.59

78.7

2.91

37.6

1.62

79.7

2.93

38.6

1.65

80.7

2.96

39.6

1.67

81.7

2.99

40.5

1.70

82.7

3.02

41.4

1.73

83.6

3.05

42.4

1.76

84.6

3.08

43.3

1.79

85.7

3.11

44.3

1.82

86.7

3.13

45.2

1.85

87.8

3.16

46.1

1.88

88.9

3.19

47.0

1.91

90.1

3.22

48.0

1.94

91.1

3.25

48.9

1.97

92.2

3.28

JOHNSON CONTROLS

321

MAINTENANCE

FORM 201.23-NM1 (910)

TABLE 33 - pressure transducer OUTput voltage (measured signal to return AT THE TRANSDUCER)
Suction Pressure
Transducer
(125 PSIG)

322

Discharge Pressure
Transducer
(275 PSIG)

Discharge Pressure
Transducer
(275 PSIG)

Pressure

Voltage

Pressure

Voltage

Pressure

Voltage

0.50

0.50

140

2.54

0.66

0.57

145

2.61

10

0.82

10

0.65

150

2.68

15

0.98

15

0.72

155

2.75

20

1.14

20

0.79

160

2.83

25

1.30

25

0.86

165

2.90

30

1.46

30

0.94

170

2.97

35

1.62

35

1.01

175

3.05

40

1.78

40

1.08

180

3.12

45

1.94

45

1.15

185

3.19

50

2.10

50

1.23

190

3.26

55

2.26

55

1.30

195

3.34

60

2.42

60

1.37

200

3.41

65

2.58

65

1.45

205

3.48

70

2.74

70

1.52

210

3.55

75

2.90

75

1.59

215

3.63

80

3.06

80

1.66

220

3.70

85

3.22

85

1.74

225

3.77

90

3.38

90

1.81

230

3.85

95

3.54

95

1.88

235

3.92

100

3.70

100

1.95

240

3.99

105

3.86

105

2.03

245

4.06

110

4.02

110

2.10

250

4.14

115

4.18

115

2.17

255

4.21

120

4.34

120

2.25

260

4.28

125

4.50

125

2.32

265

4.35

130

2.39

270

4.43

135

2.46

275

4.50

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE 34 - motor temperature sensor resistance (CHECK AT THE MOTOR)


Temp.
(C)

Rnominal
(Ohms)

Rtol
( %)

Rmin
(Ohms)

Rmax
(Ohms)

-20

97,062

5.00

92,209

101,915

-15

77,941

4.60

69,586

76,296

-10

55,391

4.20

52,996

57,643

-5

42,324

3.85

40,695

43,954

32,654

3.50

31,511

33,797

25,396

3.15

24,596

26,196

10

19,903

2.80

19,346

20,461

15

15,713

2.50

15,321

16,106

20

12,493

2.20

12,218

12,768

25

10,000

2.00

9,800

10,200

30

8,056

2.40

7,863

8,250

35

6,531

2.70

6,354

6,707

40

5,326

3.00

5,166

5,485

45

4,368

3.25

4,226

4,510

50

3,602

3.50

3,476

3,728

55

2,986

3.75

2,874

3,098

60

2,488

4.00

2,389

2,588

65

2,083

4.25

1,995

2,172

70

1,753

4.50

1,674

1,832

75

1,481

4.75

1,411

1,551

80

1,257

5.00

1,194

1,321

85

1,071

5.20

1,016

1,127

90

916.9

5.40

867.4

966.4

95

787.7

5.60

743.6

831.9

100

679.3

5.80

639.9

718.7

105

587.9

6.00

552.6

623.2

110

510.6

6.20

479.9

542.3

115

445.0

6.40

416.5

473.5

120

389.0

6.60

363.4

414.7

125

341.2

6.70

318.4

364.1

130

300.2

6.90

279.5

320.9

135

264.9

7.10

246.1

283.7

140

234.4

7.30

217.3

251.5

145

208.0

7.40

192.6

223.3

150

185.0

7.50

171.1

198.9

JOHNSON CONTROLS

323

MAINTENANCE

FORM 201.23-NM1 (910)

TABLE 35 - Compressor motor overload settings and Max. vsd frequency


2 Comp Chiller Models with Standard (pin 52 = X) and Ultra Quiet Fans (pin 52 = L)
Chiller Model
(2 Comp)
w/ STD & UQ FANS

Chiller Nameplate Voltage


(VAC)

Compressor 1
Compressor 2
Overload Setting Overload Setting
(Amps)
(Amps)

YCIV0590EA/VA

400

255

255

186

YCIV0600SA/PA

400

260

260

200

YCIV0630EA/VA

400

249

261

200

YCIV0650SA/PA

400

289

254

182

YCIV0700EA/VA

400

289

246

192

YCIV0720SA/PA

400

289

261

200

YCIV0760EA/VA

400

289

289

182

YCIV0800EA/VA

400

289

289

192

YCIV0770SA/PA

400

289

289

186

YCIV0830EA/VA

400

289

289

200

YCIV0840SA/PA

400

289

289

200

YCIV0930EA/VA

400

345

299

200

YCIV0920SA/PA

400

345

314

200

YCIV1000SA/PA

400

345

345

200

Maximum VSD
Frequency (Hz)

2 Comp Chiller Models with 2-Speed Fans


Chiller Model
(2 Comp)
w/ 2-SPD
FANS

Chiller nameplate Voltage


(VAC)

YCIV0590EA/VA

400

262

262

186

YCIV0600SA/PA

400

268

268

200

YCIV0630EA/VA

400

255

270

200

YCIV0650SA/PA

400

289

261

182

YCIV0700EA/VA

400

289

252

192

YCIV0720SA/PA

400

289

270

200

YCIV0760EA/VA

400

289

289

182

YCIV0800EA/VA

400

289

289

192

YCIV0770SA/PA

400

289

289

186

YCIV0830EA/VA

400

289

289

200

YCIV0840SA/PA

400

289

289

200

YCIV0930EA/VA

400

345

309

200

YCIV0920SA/PA

400

345

328

200

YCIV1000SA/PA

400

345

345

200

Compressor 1
Compressor 2
Overload Setting Overload Setting
(Amps)
(Amps)

Maximum VSD
Frequency (Hz)

NOTE: Overload settings are based on Chiller Model and Condenser Fan Option

324

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

TABLE 35 - Compressor motor overload settings and Max. vsd frequency (CONT'D)

2 Comp Chiller Models with High Head/High Static Fans (pin 52 = H)


Chiller Model
(2 Comp)
w/ HH/HS
FANS

Chiller Nameplate Voltage


(VAC)

YCIV0590EA/VA

400

255

255

186

YCIV0600SA/PA

400

260

260

200

YCIV0630EA/VA

400

249

261

200

YCIV0650SA/PA

400

289

254

182

YCIV0700EA/VA

400

289

246

192

YCIV0720SA/PA

400

289

261

200

YCIV0760EA/VA

400

289

289

182

YCIV0800EA/VA

400

289

289

192

YCIV0770SA/PA

400

289

289

186

YCIV0830EA/VA

400

289

289

200

YCIV0840SA/PA

400

289

289

200

YCIV0930EA/VA

400

345

299

200

YCIV0920SA/PA

400

345

314

200

YCIV1000SA/PA

400

345

345

200

Compressor 1
Compressor 2
Overload Setting Overload Setting
(Amps)
(Amps)

Maximum VSD
Frequency (Hz)

3 Comp Chiller Models with Standard (pin 52 = X) and Ultra Quiet Fans (pin 52 = L)
Chiller Model
(3 Comp)
w/ STD &
UQ FANS

Chiller Nameplate Voltage


(VAC)

Compressor
1 Overload
Setting
(Amps)

Compressor
2 Overload
Setting
(Amps)

Compressor
3 Overload
Setting
(Amps)

Maximum VSD
Frequency (Hz)

YCIV1050EA/VA

400

289

289

253

182

YCIV1070SA/PA

400

289

289

255

186

YCIV1120EA/VA

400

289

289

289

178

YCIV1180SA/PA

400

289

289

289

188

YCIV1220EA/VA

400

289

289

289

192

YCIV1340SA/PA

400

314

314

338

200

YCIV1380EA/VA

400

338

338

293

192

YCIV1500SA/PA

400

338

338

338

200

NOTE: Overload settings are based on Chiller Model and Condenser Fan Option

JOHNSON CONTROLS

325

MAINTENANCE

FORM 201.23-NM1 (910)

TABLE 35 - Compressor motor overload settings and Max. vsd frequency (CONT'D)

3 Comp Chiller Models with 2-Speed Fans


Chiller Model
(3 Comp)
w/ 2-SPD FANS

Chiller Nameplate Voltage


(VAC)

Compressor
1 Overload
Setting
(Amps)

Compressor
2 Overload
Setting
(Amps)

Compressor
3 Overload
Setting
(Amps)

Maximum VSD
Frequency (Hz)

YCIV1050EA/VA

400

289

289

260

182

YCIV1070SA/PA

400

289

289

262

186

YCIV1120EA/VA

400

289

289

289

178

YCIV1180SA/PA

400

289

289

289

188

YCIV1220EA/VA

400

289

289

289

192

YCIV1340SA/PA

400

328

328

338

200

YCIV1380EA/VA

400

338

338

304

192

YCIV1500SA/PA

400

338

338

338

200

3 Comp Chiller Models with High Head/High Static Fans (pin 52 = H)


Chiller Model
(3 Comp)
w/ HH/HS FANS

Chiller Nameplate Voltage


(VAC)

Compressor
1 Overload
Setting
(Amps)

Compressor
2 Overload
Setting
(Amps)

Compressor
3 Overload
Setting
(Amps)

Maximum VSD
Frequency (Hz)

YCIV1050EA/VA

400

289

289

253

182

YCIV1070SA/PA

400

289

289

255

186

YCIV1120EA/VA

400

289

289

289

178

YCIV1180SA/PA

400

289

289

289

188

YCIV1220EA/VA

400

289

289

289

192

YCIV1340SA/PA

400

314

314

338

200

YCIV1380EA/VA

400

338

338

293

192

YCIV1500SA/PA

400

338

338

338

200

NOTE: Overload settings are based on Chiller Model and Condenser Fan Option

326

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

Printer designs change rapidly. The


user should use the printer manual
for the respective printer for set-up
and wiring.

printer wiring
A serial printer may be connected to the TB1 connector on the Chiller Logic Board for the purposes of logging data and troubleshooting. Weightronix Imp-2600,
Seiko DPU-414, and Okidata Microline 184 printers or
equivalents may be used.

Data from the chiller is transmitted at 1200 baud. Wiring diagrams for cables are shown below:

OKIDATA MICROLINE 184


25 pin RS-232 (DB-25P)

TB1 Chiller Control Board


RS-232

11
3
7

CTS

DSR

TB1-2

RD

TXD

TB1-3

GND

GND

TB1-5

9
SEIKO DPU-414
9 pin RS-232 (DB-9)

8
3
5

TB1 Chiller Control Board

CTS

DSR

TB1-2

RD

TXD

TB1-3

GND

GND

TB1-5

WEIGHTRONIX IMP-24, MODEL 2600


25 pin RS-232 (DB-25P)

5
2
7

TB1 Chiller Control Board

CTS

DSR

TB1-2

RD

TXD

TB1-3

GND

GND

TB1-5
ld10638

fig. 60 - print cable - chiller to serial printer


JOHNSON CONTROLS

327

MAINTENANCE

With High Speed Serial Board

Printer Cables
Printer cables should be shielded coaxial, #18AWG,
stranded wire cables, not to exceed 50 in length. On
long cable runs or whenever permanent installation is
required, the shield of the coax should be tied to the
chassis ground at the chiller only, not at the printer.
Printer Setup
The following information may be useful for quick
set up of a printer. Specific printer manuals should
be utilized, if problems occur, since functions often
change as new versions of printers are introduced with
enhancements requiring control code, signal programming, and wiring changes.
Okidata 184
Control Board Switch Settings






SW1 ON:
2 OFF:
3 OFF:
4 OFF:
5 ON:
6 OFF:
7 ON:
8 OFF:

Unslashed 0
Unslashed 0
Unslashed 0
Form Length 11 in.
Form Length 11 in.
Auto Line feed OFF
8 bit data
Enable front panel

With Super Speed Serial Board
















328

FORM 201.23-NM1 (910)

SW1-1 ON: Odd or even parity


1-2 ON: No parity
1-3 ON: 8 bit data
1-4 ON: Protocol ready/busy
1-5 ON: Test select
1-6 ON: Print mode
1-7 OFF: SDD(-) pin 11
1-8 ON: SDD(-) pin 11
2-1 ON: 1200 baud
2-2 ON: 1200 baud
2-3 OFF: 1200 baud
2-4 OFF: DSR active
2-5 ON: Buffer threshold 32 bytes
2-6 ON: Busy signal 200ms
2-7 ON: DTR space after power on
2-8 not used

SW1 OFF: (-) Low when busy


2 OFF: 1200 baud
3 OFF: 1200 baud
4 ON: 1200 baud
5 not used
6 OFF: no parity
7 OFF: Pin 20 and pin 11 act as busy line

Weigh-tronix IMP 24 Model 2600


SW1 OFF: 1200 baud


2 ON: 1200 baud

Seiko
DipSW1-1 OFF: Input -Serial

1-2 ON: Printing speed high

1-3 ON: Auto loading - ON

1-4 OFF: Auto LF - OFFF

1-5 ON: Setting Command - Enable

1-6 OFF: Printing density - 100%

1-7 ON: Printing density - 100%

1-8 ON: Printing density - 100%
DipSW2-1 ON: Printing Columns - 40

2-2 ON: User Font Back-up - ON

2-3 ON: Character Select - normal

2-4 OFF: Zero - slash

2-5 ON: International character setAmerican

2-6 ON: International character set American

2-7 ON: International character set American

2-8 OFF: International character set
American
DipSW3-1 ON: Data length - bits

3-2 ON: Parity Setting - no

3-3 ON: Parity condition - odd

3-4 ON: Busy control H/W busy

3-5 ON: Baud rate select - 1200

3-6 OFF: Baud rate select - 1200

3-7 ON: Baud rate select - 1200

3-8 OFF: Baud rate select - 1200

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

operating log sheet


Site and Chiller Information
JOB NAME:

START DATE:

LOCATION:

COMPRESSOR # 1 - MODEL #:

COMPRESSOR # 2 - MODEL #:

SALES ORDER #:

COMPRESSOR # 3 - MODEL #:

TECHNICIAN NAME:

COMPRESSOR # 4 - MODEL #:

CHILLER MODEL #:

SERIAL #:

SERIAL #:

Programmed Values
CHILLED LIQUID SETPOINT

PROGRAMMED CUTOUTS

Setpoint =

F(C)

Suction Pressure Cutout =

PSIG (kPa)

Range = +/-

F(C)

Low Ambient Cutout = F(C)

Display Language =

Leaving Chilled Liquid Temp. Cutout =

Chilled Liquid Mode =

F(C)

Local/Remote Mode =

High Motor Current Unload = %FLA

Display Units =
Lead/Lag Control =
Remote Temperature Reset =
Remote Current Reset =
JOHNSON CONTROLS

329

MAINTENANCE

FORM 201.23-NM1 (910)

Unit Operating Temperatures and Pressures


CHILLED LIQUID TEMPERATURES

VSD BUS VOLTAGE

Entering Temp. =

F(C)

Bus 1 =

Leaving Temp. =

F(C)

Bus 2 =

OUTDOOR AMBIENT TEMPERATURES

VSD INTERNAL AMBIENT TEMPERATURE

OAT =

Ambient Temp. =

F(C)

F(C)

VSD FREQUENCY

VSD COOLING SYSTEM STATUS

Actual =

ON

Command =

VSD IGBT BASEPLATE TEMPS

OFF

T1 =

F(C)

T2 =

F(C)

System Operating Temperatures, Pressures and Currents

330

SYSTEM PRESSURES

MOTOR TEMPERATURES


Oil


T1

SYS 1 SYS 2 SYS 3 SYS 4






F(C)

SYS 1 SYS 2 SYS 3 SYS 4






PSIG (kPa)

Suction

PSIG (kPa)

T2

F(C)

Discharge

PSIG (kPa)

T3

F(C)

SYSTEM TEMPERATURES

COMPRESSOR SPEED


Oil

SYS 1 SYS 2 SYS 3 SYS 4






F(C)

Suction

F(C)

Discharge

F(C)

SYSTEM CURRENT

SAT Suction

F(C)

SAT Superht

F(C)

Current

SAT Discharge

F(C)

Dsch Superht

F(C)

Current

SYS 1 SYS 2 SYS 3 SYS 4

Speed

SYS 1 SYS 2 SYS 3 SYS 4


AMPS

SYS 1 SYS 2 SYS 3 SYS 4


%FLA

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

System Operating Conditions


ECOnomizer solenoid status

System starts


SYS 1 SYS 2 SYS 3 SYS 4
Economizer



(ON/OFF)


System 1

Feed/drain valve % open

System 2


Feed Valve

SYS 1 SYS 2 SYS 3 SYS 4





System 3

Drain Valve

System 4

Oil separator level

Flash tank level


SYS 1 SYS 2 SYS 3 SYS 4

Flash Tank
Level

SYS 1 SYS 2 SYS 3 SYS 4

Fan Stage

Compressor heater (ON/OFF)


SYS 1 SYS 2 SYS 3 SYS 4

Comp Heater

System Run Time


Days Hours Mins Sec

System 1

System 2

System 3

System 4

JOHNSON CONTROLS

Check Oil Separator Oil Levels


%


Separator

SYS 1
#1
#2

SYS 2
#3
#4

SYS 3
#1
#2

SYS 4
#3
#4

Oil Level Top Glass

Condenser fan stage (0-6)

Starts

Oil Level Bot Glass



Separator
Oil Level Top Glass
Oil Level Bot Glass

Oil Separator level should be maintained so that an oil level is between


the upper and lower sight glasses.

331

MAINTENANCE

FORM 201.23-NM1 (910)

Water System Conditions


evaporator flow
Flow Rate

Evap Pressure Drop



Glycol Freeze Point

GPM
FT / LBS

(Circle One)
F (C)

Condenser Conditions
air temperature
Air ON Temperature

F (C)

Air OFF Temperature

F (C)

Notes

332

JOHNSON CONTROLS

FORM 201.23-NM1 (910)

recommended spare parts


Description

MODEL NUMBER YCIV

PART NUMBER

Fan Motor
(Standard Low Noise)

-40

024-27322-004

-46

024-27322-007

Fan Motor
(Optional Ultra Low Noise)

-40

024-34980-005

-46

024-34980-001

Fan Blade (Standard Low Noise)

ALL

026-41594-000

Fan Blade (Optional Ultra Low Noise)

ALL

026-41942-000

Core, Dehydrator

ALL

026-37450-000

Oil, Compressor (Type "L")

R-134a

011-00592-000

Sensor, Outside Air Temperature

ALL

026-28663-001

Transducer, Pressure (0-275 psig)

ALL

025-29139-003

High Pressure Cutout (297 psig)

ALL

025-39456-000

Transducer, Suction Pressure (0-125 psig)

ALL

025-29583-001

Sensor, EWT, LWT

ALL

025-40334-000

Relay Output Board

ALL

031-02479-002

VSD Logic Board Kit

ALL

031-02507-601

Controller, Valve

ALL

031-02742-000

SCR Trigger Board

50 HZ YCIV

031-02060-002

Chiller Control Board

ALL

031-02478-002

Level Sensor

ALL

025-40274-000

Feed Drain Valve

ALL

025-41565-000

JOHNSON CONTROLS

333

2010 Johnson Controls, Inc.

P.O. Box 423, Milwaukee, WI 53203


www.johnsoncontrols.com

Printed in USA 201.23-NM1 (910)


Supersedes 201.23-NM1 (510)

You might also like