Scribd
Upload
45 views

Tutorial 1fg

This document contains information about various geotechnical engineering concepts and soil tests: 1) Shear strength parameters and principal stresses are determined from shear box test results on loose silty sand. Volume changes during shear are likely based on the dry condition tested. 2) Undrained shear strength parameters c' and φ' are calculated from consolidated undrained triaxial test results on saturated clay with given drained strength parameters. 3) Undrained shear strength of clay is calculated from in situ vane shear test torque measurement using vane dimensions. 4) Angle of internal friction φ' is determined for a direct shear test on dry sand, and failure shear force is calculated for a given normal stress. 5) Angle of

Uploaded by

Anonymous Vx9KTkM8n
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
45 views

Tutorial 1fg

This document contains information about various geotechnical engineering concepts and soil tests: 1) Shear strength parameters and principal stresses are determined from shear box test results on loose silty sand. Volume changes during shear are likely based on the dry condition tested. 2) Undrained shear strength parameters c' and φ' are calculated from consolidated undrained triaxial test results on saturated clay with given drained strength parameters. 3) Undrained shear strength of clay is calculated from in situ vane shear test torque measurement using vane dimensions. 4) Angle of internal friction φ' is determined for a direct shear test on dry sand, and failure shear force is calculated for a given normal stress. 5) Angle of

Uploaded by

Anonymous Vx9KTkM8n
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INDIAN INSTITUTE OF TECHNOLOGY MADRAS, CHENNAI

Department of Civil Engineering


CE 3350 Geotechnical Engineering
Tutorial # 1: Shear Strength of Soils and Site Investigation
Note: Make suitable assumptions wherever necessary.
1. The following results were obtained when a loose silty sand (in dry condition) was tested in
shear box test.
Normal stress (kN/m2)
125
235
345
2
Maximum shearing stress (kN/m )
90
160
237
Determine: (a) The shear strength parameters of soil and (b) The magnitude of principal
stresses and orientation of principal plane for the first test. Comment on the likely volume
changes during shear.
2. The CU tests carried out on saturated normally consolidated clay showed that c u = 0 and u =
150. If the pore pressure coefficient A at failure was 0.92, what are the values of c and for
the soil?
3. An in situ vane shear test was conducted in clay soil at the bottom of borehole. A torque of
153 Nm was required to shear the soil. What was the undrained strength of clay? The vane
was 100 mm in diameter and 150 mm long.
4. For a direct shear test on a dry sand, the following are given: Specimen size: 75 mm 75
mm 30 mm (height) Normal stress: 200 kN/m2 Shear stress at failure: 175 kN/m2
(a) Determine the angle of friction,
(b) For a normal stress of 150 kN/m2, what shear force is required to cause failure in the
specimen?
5. The following are the results of four drained, direct shear tests on a normally consolidated
clay. Given: Size of specimen = 60 mm 60 mm Height of specimen = 30 mm.
Draw a graph for the shear stress at failure
against the normal stress, and
determine the drained angle of friction from the
graph.

6. For a normally consolidated clay, = 24. In a drained triaxial test, the specimen failed at a
deviator stress of 175 kN/m2. What was the chamber confining pressure 3 ?
7.

1.1

8.

9.

10.

11.

12. (a) For a Shelby tube, given: outside diameter = 76.2 mm and inside diameter = 73 mm.
What is the area ratio of the tube?
(b) Following is the variation of the field standard penetration number (N 60 ) in a sand
deposit:
The groundwater table is located at a depth of 6
m. Given: the dry unit weight of sand from 0 to a
depth of 6 m is 18 kN/m3 and the saturated unit
weight of sand for depth 6 to 12 m is 20.2 kN/m3.
Using the relationship of Skempton, calculate the
corrected penetration numbers.

1.2

You might also like