Scribd
Upload
683 views37 pages

Batch-4 (B) - IR2110 Based Square Wave Inverter Using 555 Timer

This document describes a square wave inverter circuit design using an IR2110 driver and 555 timer. The IR2110 is a high voltage, high speed MOSFET and IGBT driver that can be used to drive the high side switch of an H-bridge up to 500V. A 555 timer generates the switching signal and is connected to the IR2110 drivers. Simulation and hardware results show the circuit can generate a square wave output across a load. The IR2110 provides advantages like very low dead time, high switching frequencies up to 100kHz, and does not require an auxiliary power supply.

Uploaded by

Кети Таневска
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
683 views37 pages

Batch-4 (B) - IR2110 Based Square Wave Inverter Using 555 Timer

This document describes a square wave inverter circuit design using an IR2110 driver and 555 timer. The IR2110 is a high voltage, high speed MOSFET and IGBT driver that can be used to drive the high side switch of an H-bridge up to 500V. A 555 timer generates the switching signal and is connected to the IR2110 drivers. Simulation and hardware results show the circuit can generate a square wave output across a load. The IR2110 provides advantages like very low dead time, high switching frequencies up to 100kHz, and does not require an auxiliary power supply.

Uploaded by

Кети Таневска
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 37

IR2110 BASED SQUAREWAVE INVERTER USING 555 TIMER

By
B.Anusha (07241A0260)
N.Kalyani (07241A0272)
R.Sandhya(07241A02A0)

What is IR2110 :

The IRS2110/IRS2113 are high voltage, high speed


power MOSFET and IGBT drivers with independent
high and low side referenced output channels.

The Chips have several applications like motor drives,


lighting

blast,

switched

mode

Automotives, Plasma Display panels.

power

supplies,

Technical Features of IR2110 :


Logic inputs are compatible with standard CMOS or
LSTTL output, down to 3.3 V logic.
The floating channel can be used to drive an N-channel
power MOSFET or IGBT in the high side configuration
which operates up to 500 V or 600 V.
The IRS2110/IRS2113, has a floating channel which
provides gate drive for the high side switch.
The gate drive supply range is quite wide (10 V to 20
V).

Design Features of IR2110 :

Floating channel designed for bootstrap operation


Fully operational to +500 V or +600 V
Tolerant to negative transient voltage, dV/dt immune.
Gate drive supply range from 10 V to 20 V.
Undervoltage lockout for both channels.
3.3 V logic compatible.
Separate logic supply range from 3.3 V to 20 V.
Logic and power ground 5 V offset.
CMOS Schmitt-triggered inputs with pull-down.
Cycle by cycle edge-triggered shutdown logic.
Matched propagation delay for both channels.
Outputs in phase with inputs.

Pin Diagram of IR2110 :

Description of Pin :

VDD - Logic supply.


HIN - Logic input for high side gate driver output (HO),
in phase.
SD - Logic input for shutdown.
LIN - Logic input for low side gate driver output (LO), in
phase.
VSS - Logic ground.
VB - High side floating supply.
HO - High side gate drive output.
VS
- High side floating supply return.
VCC - Low side supply.
LO
- Low side gate drive output.
COM - Low side return.

Block Diagram :

Definitions:

PULSE DISCRIMINATOR:

It filters or screens out pulses shorter than 50ns or so.

LEVEL TRANSLATOR:

It adjusts the level of the input signal acccording to the


signal required.

UV DETECT:
It prevents either channel from operating if Vcc is below
the specified valu(8.6/8.2V).

Application circuit- H-bridge using


IR2110 devices

Modified Circuit Of H-bridge :

Circuit diagram:

555 Timer Astable Circuit:

+15V Supply Circuit:

O/P Waveforms :

IR2110 SPECIFICATIONS :

IRF 640 N- CHANNEL MOSFET


SPECIFICATIONS :

74LS76 J-K FLIP FLOP


Pin diagram:

74LS76 SPECIFICATIONS:

555 TIMER :

555 TIMER SPECIFICATIONS :

Theory:
The shutdown function is latched so that the power
MOSFETs will remain in the offstate as the load current
decays through their internal diodes.
The latch is reset at the beginning of next cycle, when
the power devices are once again commanded on.
The decoupling capacitors mitigate the negative effects
of L1.
As an added safety margin a resistor diode network can
be added to the gate, as shown in modified circuit with
dashed lines.

Theory(contd)

The purpose of this network is to further delay the turnon, without affecting the turn-off, thereby inserting some
additional dead-time.
The resistor-diode network is also useful in reducing the
peak of the current spike during the reverse recovery
time.

List Of Components:
Sl.No.

Component

Ratings

Quantity

1.

IRS2110

600V

2.

555Timer

15V

3.

7815 IC

15V

4.

7805 IC

5V

5.

Resistors

470, 560, 1K, 1.2


K,22 K

6.

Capacitors

0.1uF, 220uF,
10uF,10nF,0.47uF

18

7.

JK flip flop

5.5 V

Simulation Circuit :

Simulation Results :

H-Bridge Inverter Simulation :

Simulation Result :

Inverter Simulation Circuit :

Simulation Result :

Observations:
Ra

Rb

Frequency

560

470

0.1u

9.6kHz

560

71k

0.1u

101.71Hz

1000

71k

0.1u

101.39Hz

2.2k

71k

0.1u

100.55Hz

5k

71k

0.1u

98.63Hz

Circuit Design In EAGLE :

Hardware Implementation :

Hardware Connections Of The Circuit

Circuit Connected To The Auto-Transformer

Output Waveform Obtained


Across The Load :

IR Advantages:
Dead-time as low as 500ns allows frequency up to
100khz.
Increases speed range and torque control of motor
drives.
Enable rugged gate drive design.
Low power dissipation.
Compared with opto-coupler based solutions:30% fewer
parts and 50% smaller PCB.
Doesn't need auxiliary power supply.
10X faster delay matching ( 50ns).
No degradation of performance over time.
Shorter time to signal over-current(1.5s versus 6s).

Applications :

DC Bus Converter Control ICs : Networking and


Telecommunication systems.
Current sensing ICs.
Digital Control ICs : In room and wall air conditioners,
Washing machines.
High Voltage ICs : Motor Drive, Plasma Display Panels.
Switching Regulators DC-DC : Desktop and Servers,
Graphic Cards.
Automotive Intelligent Power Switch : Interior fan
control.

THANK YOU

You might also like