Scribd
Upload
192 views

At One Place Only 2) Answer Any Four From The Remaining Questions

This document contains a model question paper for an Electrical and Electronics Engineering exam on the topic of Electrical Circuits. It includes 7 questions testing various concepts: 1) Question 1 is compulsory and contains 10 short answer questions testing definitions, circuit analysis techniques, and theorems. 2) Questions 2-7 contain multiple parts testing additional circuit analysis techniques like equivalent circuits, network parameters, transient analysis using Laplace transforms, and more. Circuit diagrams are provided. 3) Students must answer Question 1 and any 4 of the remaining 6 questions, for a total of 70 marks. Calculations of currents, voltages, powers, and network parameters are required throughout.

Uploaded by

Dinesh Sai
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
192 views

At One Place Only 2) Answer Any Four From The Remaining Questions

This document contains a model question paper for an Electrical and Electronics Engineering exam on the topic of Electrical Circuits. It includes 7 questions testing various concepts: 1) Question 1 is compulsory and contains 10 short answer questions testing definitions, circuit analysis techniques, and theorems. 2) Questions 2-7 contain multiple parts testing additional circuit analysis techniques like equivalent circuits, network parameters, transient analysis using Laplace transforms, and more. Circuit diagrams are provided. 3) Students must answer Question 1 and any 4 of the remaining 6 questions, for a total of 70 marks. Calculations of currents, voltages, powers, and network parameters are required throughout.

Uploaded by

Dinesh Sai
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

MODEL QUESTION PAPER

FOUR YEAR B.TECH DEGREE END EXAMINATION


THIRD SEMESTER EXAMINATION
ELECTRICAL & ELECTRONICS ENGINEERING
ELECTRICAL CIRCUITS (EC)
(SCHEME-2013)

Time: 3 Hours

Max.Marks:70

Note: 1) Question No. 1 is compulsory & it must be answered first in sequence


at one place only
2) Answer any four from the remaining questions.
1.

a)
b)
c)
d)
e)
f)
g)
h)

Answer the following:


10 1 = 10M
Define tree and co-tree
Define mutual inductance
Draw the locus diagram for RC series circuit
Write the relation between line and phase quantities of a star connected system
Define resonant frequency and band width
State Tellegens theorem
Express h11 and h21 in terms of Z parameters
Find the response of the circuit shown if the switch is closed at t=0sec.

i)
j)

Find the laplace transform of function f(t) = te-at


What will be the approximate voltage across the inductor 100ns after the switch is closed.

a) Find the equivalent resistance of the circuit shown and find the current produced by 10V
source
(7M)

b) Write the tieset schedule for the circuit shown below develop the equilibrium equations.
(8M)

a) Briefly explain the concept of duality with an example

(6M)
P.T.O

b) For the network shown in figure find the current flowing through the load resistance (9M)

a) If Z1 = 20 -300, Z2 = 40 800 and Z3 = 10 +900 are the impedances connected in the


form of delta and the supply voltage is 440v. Assume the RYB sequence and so find the
phase currents, line currents and the total power absorbed.
(7M)
b) Derive the relation between the line and phase quantities of the star connected system with
neat phasor diagram.
(8M)

a) Derive the expression for the bandwidth of a series RLC circuit.


(7M)
b) Calculate the current through the 3resistor in the circuit shown in figure shown using
superposition theorem. Also calculate the power across the 3 resistor.
(8M)

a) Find the Z parameters of the two port network shown

(7M)

b) Obtain the hybrid parameters of the network shown

(8M)

a) The circuit shown in figure consists of resistance, inductance, and capacitance in series
with a 200 V constant source. When the switch is closed at t = 0. Find the transient current.
(7M)

b) In the circuit shown in figure the switch is moved from 1 to 2 at time t = 0. The steadystate current having previously established in the R-L circuit, find the expression for the
current i(t) after switching using laplace transform method.
(8M)

You might also like