Scribd
Upload
1K views2 pages

10 TV 004

The document provides instructions for recovering a TV set using a software recovery tool stored on a memory stick. Key steps include: 1. Formatting a memory stick of at least 16MB in size and creating the proper folder structure to store recovery files. 2. Downloading and copying the software recovery tool (.ram file) and NVM data (.tar file) to the memory stick. 3. Inserting the memory stick into the TV, powering on, and allowing the recovery process to complete, which can take 30 seconds. 4. Replacing the BA board if needed and updating the software package to the latest version after recovery is finished.

Uploaded by

Fly Ku
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views2 pages

10 TV 004

The document provides instructions for recovering a TV set using a software recovery tool stored on a memory stick. Key steps include: 1. Formatting a memory stick of at least 16MB in size and creating the proper folder structure to store recovery files. 2. Downloading and copying the software recovery tool (.ram file) and NVM data (.tar file) to the memory stick. 3. Inserting the memory stick into the TV, powering on, and allowing the recovery process to complete, which can take 30 seconds. 4. Replacing the BA board if needed and updating the software package to the latest version after recovery is finished.

Uploaded by

Fly Ku
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Technical Bulletin

Date

Ref. No.

Model

22.01.10

10TV004

EX-2L_Basil_Sat, EX-2L_Coriander_Sat, EX-2L_Paprika_Sat Chassis

Subject

BC
IRIS

Software Recovery Tool for BA Board

111A

SYMPTOM
No picture may appear, while the green LED is on.
CAUSE
Damaged NVM data on BA board.
SOLUTION
Recover the TV set by applying the Software Recovering Tool using a Memory Stick.
1. Preparation Memory Stick Requirements
x

Remove unnecessary files from the MS before copying data.

Use a Memory Stick formatter to format. Windows formatters are not supported.

A format program can be downloaded from:


http://support.sony-europe.com/memstick/downloads/downloads_ms.asp?l=en&f=MSFRM#disc

It is, however, recommended to use a Digital camera to format!

After formatting, the content in the MS is just a Memstick.ind file.

The flash size must be 16 MB or more.

2. Recovery procedure
2-1. In the Memory Stick, create a folder eg2l_dvt containing a subfolder swupdate.
2-2. Download the attached zip file, including the software recovery tool (RAM file) and NVM data (TAR file),
attached to this Technical Bulletin.
Date

Attachment

January 2010

10TV004_Satellite.zip

Condition
code
1

Symptom
code
11A

File
app_install_eg2l_dvt_0.146.40-20100119-256-sig_aquaFlash1Recover.ram
nvm_AEP.tar

Part
number

Ref.
10TV004

Section
code
FMW

PWB
BA

Defect
code
N

Repair
code
3

Qty.

Sony Europe (Belgium) NV


Customer Satisfaction Europe
Quality & Service Engineering
1/2

2/2

10TV004

2-3. Copy the RAM file in the eg2l_dvt/swupdate folder.


2-4. Copy the TAR file into root directory of the Memory Stick. The MS root folder should look as below (Make sure
that Show hidden files and folders is activated in the Explorer Options).

2-5. Power off the set and unplug the AC cord.


2-6. Insert the Memory Stick into the erroneous BA board and turn on the TV.
2-7. Wait for about 30 seconds until Initial setup is shown. If you can see the EMMA log, wait until the EMMA
application is launched.
2-8. Turn off the TV.
IMPORTANT
After the recovery process, the TV can go in Error mode, i.e. LED changing from green to Red blinking 14
times (T-Con error) due to generic NVM data not matching to current set size. Therefore, make sure to
write the correct NVM version.
2-9. Follow the BA board replacement procedure as described in TB 09TV097. Although the BA board does not
have to be replaced for this issue, it assures correct settings and memory values for each model.
2-10. Update to software package #1.700 or higher, using the software attached to TB 09TV093.
2-11. Check the MAC Address value in Menu => Settings => Network settings => Network.
NOTE: If the MAC address is empty (6 times 00), this board cannot be used and must be returned for central
repair.

You might also like