Scribd
Upload
25 views4 pages

Experiment No. 04

The objective of this experiment is to carry out closed loop control using an on/off controller to open and close three solenoid valves and activate pump 2 with a proportional integral controller. The apparatus includes a UCP-L control interface, control software, and water. Graphs show the response of the proportional integral controller at different gain levels, with a higher gain resulting in greater oscillation. Integral control is described as causing a system to continuously increase or decrease the controlled variable without reaching a new equilibrium. An example is given of liquid level in a tank, which will rise or fall until limited by overflow or emptying.

Uploaded by

fahadfiaz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
25 views4 pages

Experiment No. 04

The objective of this experiment is to carry out closed loop control using an on/off controller to open and close three solenoid valves and activate pump 2 with a proportional integral controller. The apparatus includes a UCP-L control interface, control software, and water. Graphs show the response of the proportional integral controller at different gain levels, with a higher gain resulting in greater oscillation. Integral control is described as causing a system to continuously increase or decrease the controlled variable without reaching a new equilibrium. An example is given of liquid level in a tank, which will rise or fall until limited by overflow or emptying.

Uploaded by

fahadfiaz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Experiment No.

The objective of this practice is to carry out a closed loop control by an


on/off controller by the closing and opening of the A VS-I, AVS-2, AVS-3
solenoid valves and the activation of pump 2 using proportional integral
controller.

Apparatus:

UCP-L
Control and Acquisition Software
Water

Diagram:

Procedure:

Connect the interface of the equipment and the control software


Select the control on/off option
Make a double click on the on/off control, select the flow wanted. there are
a certain flow, a tolerance and a performance time set by default. It allows
the students to play with these parameters and see the influences of each
one
The level control can be carried out by the activation of a single actuator,
or of several ones, to which different tolerances are allowed. These
controllers work as security system measures when the controlled variable
exceeds in a tolerance the set value. To activate or to disable any of these
controllers you may have to double click on each of them and press the
button "PAUSE"

Calculate the inertia of the system for an on/off response and determine
the limit time for an exact control

PI GRAPH
120
100
80

SC-1

60
40
20
0

T
he following graph is obtained when we set the gain upto 0.005

If we increase the gain upto 0.05 then

PI CONTROLLER GRAPH
120
100
80
SC-1

60
40
20
0

Axis Title

But further increasing the gain upto 0.2 shows us following relation

PI CONTROLLER
120
100
80
SC-1

60
40
20
0

time

I Controller
Integral controlled systems are systems without self-regulation: if the
manipulated variable does not equal zero, the integral controlled system
responds with a continuous change continuous increase or decrease of the
controlled variable. A new equilibrium is not reached.

Liquid level in a tank


In a tank with an outlet and equally high supply and discharge flow rates, a
constant liquid level is reached. If the supply or discharge flow rate changes, the
liquid level will rise or fall. The level changes the quicker, the larger the
difference between supply and discharge flow.
This example shows that the use of integral control action is mostly limited in
practice. The controlled variable increases or decreases only until it reaches a
system-related limit value: the tank will overflow or be discharged, maximum or
minimum system pressure is reached, etc.

Comments

You might also like