TUTORIAL SERIES FOR

VERSION 8
TUTORIAL 6
LATHE - 3D GEOMETRY; FACE, ROUGH AND FINISH;
FACE CONTOUR; CROSS CONTOUR; C-AXIS CONTOUR; FACE
DRILL; CROSS DRILL; CUTOFF

TUTORIAL 6
Objectives:
To design a 3 dimensional drawing by:
!"Creating the 2D geometry in different construction planes at different construction depths.
!"Using Xform, Translate to create the 3D wireframe
To establish Job setup settings:
!"Stock size.
!"Tool offsets.
!"Tool clearance.
!"Material of the part.
!"Feed calculation.
To create a 2 dimensional lathe toolpaths consisting of:
!"Face cutting the part.
!"Rough machining the part.
!"Finish machining the part.
!"Cutoff the part.
To create C-axis milling toolpaths consisting of:
!"Face contour
!"Cross contour
!"C-axis contour
!"Face drilling
!"Cross drilling
To check the toolpath using Mastercams Verify verification module by:
!"Running the Verify function to machine the part on the screen.

Page 6-1

TUTORIAL 6

Page 6-2

TUTORIAL 6

GEOMETRY CREATION
STEP 1:
CREATE THE 1 DIAMETER CYLINDER.
Change the Construction plane and the Graphic view to Side.
MAIN MENU
#"Cplane
#"Side
#"Gview
#"Side

Select Cplane
here

MAIN MENU
#"Create
#"Arc
#"Circ pt + dia
#"[ Enter the diameter ] 2
#"Origin
#"Press Esc to exit the command

Select Gview
here

MAIN MENU
#"Xform
#"Translate
#"Select the arc.
#"Done
#"Rectang
#"[ Enter the translation vector ]: Z -1

#"Select OK button.

Page 6-3

TUTORIAL 6
STEP 2:
CREATE THE 3D WIREFRAME OF THE CONTOUR WITH FILLET RADII
OF .375.
Change the construction depth to Z-1
#"Select Z from the secondary menu as shown in the following picture.
Select Z
here

#"[ Select point for new construction depth ]: -1

Make sure that Autocursor is enabled.

#"Right-mouse click in the middle of the screen.
#"AutoCursor should have the check mark in front as shown in the following dialog
box.

#"Press

Esc to exit the dialog box.

Page 6-4

TUTORIAL 6
MAIN MENU
#"Create
#"Line
#"Polar
#"[Specify an endpoint]: Select the Endpoint of the arc as shown in the picture.

#"[
#"[

Enter the angle in degrees ]: 35

Enter the line length ]: 2

#"[Specify an endpoint]: Select the same Endpoint of the arc as shown in the previous
picture.
#"[ Enter the angle in degrees ]: -35
#"[ Enter the line length ]: 2

#"[Specify an endpoint]: Select the Quadrant of the arc as shown in the picture.
#"[ Enter the angle in degrees ]: 90-35
#"[ Enter the line length ]: 2

Page 6-5

TUTORIAL 6
MAIN MENU
#"Create
#"Arc
#"Circ pt + dia
#"[ Enter the diameter ] 4
#"Origin
#"Press Esc to exit the command
#"Using

the toolbar located at the top of the screen, fit the drawing to the
screen.

MAIN MENU
#"Create
#"Fillet
#"Radius
#"[Enter the fillet radius]: .375
#"[ Select an entity ]: Select entity C
#"[ Select an other entity ]: Select entity A
#"[
#"[

Select an entity ]: Select entity A

Select an other entity ]: Select entity B

#"[
#"[

Select an entity ]: Select entity B

Select an other entity ]: Select entity D

Select
Entity C
here

MAIN MENU
#"Delete
#"Select the line as shown in the following picture.

Select
Entity A
here

Select
Entity B
here

Select
Entity D
here

Delete this
line

Page 6-6

TUTORIAL 6
MAIN MENU
#"Xform
#"Rotate
#"Chain
#"Options
#"Set the default chaining mode to Full

#"Select the contour as shown in the picture.

#"Done
#"Done
#"[ Enter the point to rotate about]
#"Origin

Page 6-7

Select the
contour
here

TUTORIAL 6
#"Select OK button.
#"Using the toolbar located

at the top of the screen, fit the drawing to the screen.

MAIN MENU
#"Modify
#"Trim
#"2 entities
Select
Entity B
here

Select
Entity A
here

Select
Entity C
here

Select
Entity H
here

Select
Entity D
here

Select
Entity G
here
Select
Entity E
here

Select
Entity F
here

#"[
#"[

Select entity to trim ]: Select Entity A

Select the entity to trim to]:Select Entity B

#"[
#"[

Select entity to trim ]: Select Entity C

Select the entity to trim to]:Select Entity D

#"[
#"[

Select entity to trim ]: Select Entity E

Select the entity to trim to]:Select Entity F

#"[
#"[

Select entity to trim ]: Select Entity G

Select the entity to trim to]:Select Entity H

Page 6-8

TUTORIAL 6
MAIN MENU
#"Xform
#"Translate
#"Chain

Select this
contour

#"Select the contour as shown in the picture.

#"Done
#"Done
#"Rectang
#"[ Enter the translation vector]: Z-.5

#"Select

OK button.

Change the Graphic View to Isometric.

The part should look as shown in the following picture.

Page 6-9

TUTORIAL 6
STEP 3:
CREATE THE 5.5 DIAMETER CYLINDER.
Change the Gview and the Cplane back to Side.
Change the construction depth to Z-1.5 as shown at pag 6-3

MAIN MENU
#"Create
#"Arc
#"Polar
#"Center pt
#"[Enter the center point]:
#"Origin
#"[ Enter the radius]: 2.75
#"[ Enter the initial angle]: 0
#"[ Enter the final angle]: 90
#"Using the toolbar located at the top of the screen, fit the drawing to the screen.
#"[Enter the center point]:
#"Origin
#"[ Enter the radius]: 2.625
#"[ Enter the initial angle]: 0
#"[ Enter the final angle]: 90

MAIN MENU
#"Create
#"Line
#"Polar
#"[Specify an endpoint]:
#"Origin
#"[ Enter the angle in degrees ]: 45
#"[ Enter the line length ]: 3
MAIN MENU
#"Create
#"Line
#"Parallel
#"Side/dist
#"[ Select line]: Select the 45 deg. line
#"[ Indicate the offset direction]: Select a point at the left side of the line
#"[ Parallel line distance]: .125

Page 6-10

TUTORIAL 6

#"[ Select line]: Select the 45 deg. line

#"[ Indicate the offset direction]: Select a point at the right side of the line
#"[ Parallel line distance]: .125
MAIN MENU
#"Modify
#"Trim
#"Divide
#"[ Select curve to divide]:Select Entity A
#"[ Select the first dividing curve]: Select Entity B
#"[ Select the second dividing curve]: Select Entity C

Select
Entity B

Select
Entity A

Select
Entity C

BACKUP
#"3 entities
#"[ Select the first entity to trim ]: Select Entity A
#"[ Select the second entity to trim ]: Select Entity B
#"[ Select the entity to trim to ]: Select Entity C
Select
Entity A
here
Select
Entity B
here

Select
Entity C
here

Page 6-11

TUTORIAL 6
BACKUP
#"1 entities
#"[ Select the
#"[ Select the

first entity to trim ]: Select Entity A

entity to trim to ]: Select Entity B
Select
Entity B
here

Select
Entity A
here

Select
Entity D
here

Select
Entity C
here
#"[
#"[

Select the first entity to trim ]: Select Entity C

Select the entity to trim to ]: Select Entity D

MAIN MENU
#"Delete
#"Select the 45 deg line as shown in the
following picture.
MAIN MENU
#"Xform
#"Rotate
#"Chain
#"Select the contour as shown in the
picture.
#"Done
#"Done
#"[ Enter the point to rotate about]
#"Origin

Page 6-12

Delete this
Entity
Select this
contour

TUTORIAL 6

#"Select OK button.
#"Using the toolbar located

at the top of the screen, fit the drawing to the screen.

MAIN MENU
Select the
#"Xform
contour
#"Translate
here
#"Chain
#"Select the contour as shown in the picture.
#"Done
#"Done
#"Rectang
#"[ Enter the translation vector]: Z-2

#"Select

OK button.

MAIN MENU
#"Screen
#"Clr colors

Page 6-13

TUTORIAL 6
Change the Graphic View to Isometric and fit the geometry to the screen.
The part should look as shown in the following picture.

STEP 4:
CREATE THE CENTER POINTS OF THE .25 DIAMETER HOLES.
Change The Cplane and the Gview back to Side.
MAIN MENU
#"Create
#"Point
#"Next menu
#"Bolt circle
#"Radius
#"[ Radius =]: 3.5/2
#"Incr angle
#"[ Incremental angle =]: 90
#"Num of pts
#"[ Number of points =]: 4
#"Do it
#"Origin
#"Press Esc to exit the command.
$For machining purpose you only need the center points. You can create the arcs
following the next steps.

Page 6-14

TUTORIAL 6
MAIN MENU
#"Create
#"Arc
#"Circ pt + dia
#"[ Enter the diameter ] .25
#"Select the points that you have just created to establish the center points of the
arcs.
#"Press Esc to exit the command.

STEP 5:
CREATE THE 3 POINTS AND THE 3D ARC THAT GOES THROUGH
THE POINTS.
MAIN MENU
#"Create
#"Point
#"Position
#"[ Specify a point]: 1,0,0
#"[ Specify a point]: 0,1,-.25
#"[ Specify a point]: -1,0,-.5

Change the Graphic View to Isometric and Cplane to 3D.

MAIN MENU
#"Create
#"Arc
#"3 points
#"[ Enter the first point ]: Select Point 1
#"[ Enter the second point ]: Select Point 2
#"[ Enter the third point ]: Select Point 3

Page 6-15

TUTORIAL 6

Select
Point 2

Select
Point 3
Select
Point 1

The part should look as shown in the following picture.

Page 6-16

TUTORIAL 6
STEP 6:
CREATE THE CENTER POINTS OF THE .25 DIAMETER HOLES.
Change the Gview and the Cplane to Side.
Change the construction depth to Z -2.5
MAIN MENU
#"Create
#"Point
#"Next menu
#"Bolt circle
#"Radius
#"[ Radius =]: 5.5/2
#"Incr angle
#"[ Incremental angle =]: 90
#"Num of pts
#"[ Number of points =]: 4
#"Do it
#"Origin
#"Press Esc to exit the command.
For machining purpose you only need the center points. You can create the arcs
following the next steps.
Change the Cplane to Top.
Change the construction depth to Z 2.75
MAIN MENU
#"Create
#"Arc
#"Circ pt + dia
#"[ Enter the diameter ] .5
#"Type the centerpoint coordinates: -2.5, 0
#"Press Esc to exit the command.

Page 6-17

TUTORIAL 6

Change the Cplane to Side.

MAIN MENU
#"Xform
#"Rotate
#"Select the arc as shown in the
picture.
#"Done
#"[ Enter the point to rotate about]
#"Origin

Select this
arc

#"Select

OK button.
The final part should look as shown in the following picture.

Page 6-18

TUTORIAL 6
For machining purpose we have to create extra geometry.
STEP 7:
CREATE THE CENTER LINES OF THE .25 WIDTH CHANELS.
Change the Cplane to 3D.
MAIN MENU
#"Create
#"Line
#"Endpoints
#"[ Specify the first endpoint]:
#"Midpoint
#"Select Entity A
#"[ Specify the second endpoint]:
#"Midpoint
#"Select Entity B

Select
Entity A
here

Select
Entity B
here

Page 6-19

TUTORIAL 6

MAIN MENU
#"Modify
#"Extend
#"Length
#"[ Enter the length to extend]: .2
#"[ Select a curve near the endpoint to extend]: Select Entity A close to one endpoint
as shown in the following picture.

Select entity A
close to this
endpoint

Change the Cplane to Side.

MAIN MENU
#"Xform
#"Rotate
#"Select the line as shown in the
picture.
#"Done
#"[Enter the point to rotate about]
#"Origin

Select this
line

Page 6-20

TUTORIAL 6

#"Select

OK button.

MAIN MENU
#"Screen
#"Clr colors

STEP 8:
CREATE HALF OF THE 2D GEOMETRY.
#"Change the
#"Cplane
#"Next Menu
#"3 +dz
#"Change

Cplane to + dZ.
Select
Cplane
here

the Gview to Top

Select
Gview
here
Page 6-21

TUTORIAL 6
#"Change
#"Level

the main Level 1 to Level 2

Select
Level here

#"Change

the Main Level Number to 2

Click here to
make level1
invisible

Change the
Main level
number to 2

#"Make

Level 1 invisible by disable the check mark next to Level 1 as shown in the
above screen shot.
#"Select OK button to exit.
#"Select F3 key to repaint the screen.
$Note that the 3D geometry that you just created is invisible.

Page 6-22

TUTORIAL 6
Change the construction plane to Z 0.
MAIN MENU
#"Create
#"Rectangle
#"1 point

Select this Point

Placement

#"Select OK
#"Origin
#"Press Esc

button
Select
Entity A

to exit the command

MAIN MENU
#"Create
#"Line
#"Parallel
#"Side/dist
#"[ Select line]: Select Entity A
#"[ Indicate the offset direction]: Select a point at the left side of the line
#"[ Parallel line distance]: 1
#"[ Select line]: Select Entity B
#"[ Indicate the offset direction]: Select a point at the
rigth side of the line
#"[ Parallel line distance]: 2
Select
Entity B

Page 6-23

TUTORIAL 6
#"[ Select line]: Select Entity C
#"[ Indicate the offset direction]: Select a point above the line
#"[ Parallel line distance]: 1

Select
Entity C
#"[ Select line]: Select Entity C
#"[ Indicate the offset direction]: Select a point above the line
#"[ Parallel line distance]: 2

Page 6-24

TUTORIAL 6
MAIN MENU
#"Modify
#"Trim
#"2 entities
#"[ Select the entity to trim ]: Select Entity A
#"[ Select the entity to trim to]: Select Entity B
#"[
#"[

Select the first entity to trim ]: Select Entity B

Select the second entity to trim ]: Select Entity C

#"[
#"[

Select the first entity to trim ]: Select Entity C

Select the second entity to trim ]: Select Entity D

#"[
#"[

Select the first entity to trim ]: Select Entity D

Select the second entity to trim ]: Select Entity E

#"[
#"[

Select the first entity to trim ]: Select Entity E

Select the second entity to trim ]: Select Entity F

Select
Entity F
here

Select
Entity D
here
Select
Entity B
here

Select
Entity E
here

Select
Entity C
here

Page 6-25

Select
Entity A
here

TUTORIAL 6
The part should look like in the following picture.

#"Using

the toolbar located at the top of the screen, fit the drawing to the screen.

STEP 9:
SAVE THE FILE.
MAIN MENU
#"File
#"Save
#"Save this file under C-axis_1

Page 6-26

TUTORIAL 6

TOOLPATH CREATION
STEP 10:
SET UP THE STOCK TO BE MACHINED
MAIN MENU
Toolpaths
#"
Job Setup
#"

1. Select
Rectangle

2. Select Material here

Under Stock select Rectangle.

#"
2 points
#"
#"[Enter the lower left corner:] 0,-5
#"[Enter coordinates:] 5.8,0.15
Select the radio button in front of material as shown in the picture above.
#"

Select OK button.
#"

Page 6-27

TUTORIAL 6

From Lathe Material List choose Aluminum 6061.

#"
Select OK.
#"

#"The Lathe Job Setup parameters screen should

look as shown in the picture below.

#"Select OK button.
#"Using the toolbar located at the top of the screen, fit the drawing to the screen.

Page 6-28

TUTORIAL 6
STEP 11:
FACE THE PART.
Refer to Lathe Tutorial #1 in the Mastercam Lathe Training Tutorials page 1-7 to 1-8.
The manual is available at your local Mastercam dealer or at
http://www.emastercam.com/resources/

STEP 12:
ROUGH THE PART.
Refer to Lathe Tutorial #1 in the Mastercam Lathe Training Tutorials page 1-9 to 1-10.

STEP 13:
FINISH THE PART.
Refer to Lathe Tutorial #1 in the Mastercam Lathe Training Tutorials page 1-11 to 1-13.

STEP 14:
CREATE A GROOVE FOR THE RELIEF CUT OFF AREA TO AVOID
INTERRUPTED CUTS.
#"Groove

#"Select OK button.
#"[Select points]:
#"Select the point as shown in the picture.
#"Press Esc button to exit checking.

Page 6-29

Select the
endpoint

TUTORIAL 6

#"Double-mouse
#"Select Holders

click on the selected tool to edit.

page and change C value to 2.5 as shown in the following screen

shot.

Page 6-30

TUTORIAL 6
#"Select
#"Select

OK button to exit tool definition.

Grove shape parameters and change the height and the width as shown

below.

#"Select

the Groove rough parameters page and make all necessary changes as
shown in the screen shot.

Page 6-31

TUTORIAL 6
#"Select

Groove finish parameter and disable the box in front of Finish groove.

#"Select

OK button to exit.

Page 6-32

TUTORIAL 6
STEP 15:
BACKPLOT THE TOOLPATH.
#"Operations
#"(From the Operations
#"(From the Operations
#"Run

Manager dialog) Select All

Manager dialog) Backplot

If you would like to watch the toolpath run slower, instead of Run, select Step. Hold
down the S key on your keyboard, or keep pressing the Step key and you will be able to
see the entire program at the speed that you wish, and be able to stop it at any time.
Press BACKUP to return to the Operations Manager dialog.
Right click on an empty space in the white box
#"
Options
#"
Toolpath display
#"
Off
#"
#"Select OK button to exit
Operations Manager.

Page 6-33

TUTORIAL 6
STEP 16:
FACE CONTOURING.
Change the Main Level to Level 1 and make invisible Level 2.
#"Level
#"To change the main level to 1 under Main Level Number type 1
#"Make invisible Level 2 by disabling the check mark next to Level 2 as shown in the
following screen shot.

Click here
to make
Level 2
invisible

Change
the Main
Level to 1

#"Select

OK button to exit.
$You shoul be able to see only the 3D part.
#"Change the Gview to Isometric.
#"Change Cplane to Side.

Page 6-34

TUTORIAL 6
MAIN MENU
#"Toolpaths
#"Next Menu
#"C-axis
#"Face ctr
#"Chain
#"Options
#"Enable Plane mask as shown in the
following screen shot.
#"Select OK button to exit Chaining
Options dialog box.

#"Select

the contour as shown in the following picture.

Select the
contour
here

Page 6-35

TUTORIAL 6
#"The chaining direction has
#"Done
#"Get from the library a 5/8

#"Select

to be CCW if not select Reverse.

Flat End Mill.

parameters and make the changes as shown in the following screen shots.

Page 6-36

TUTORIAL 6
#"Select

Multi passes button and set the parameters to match the following screen

shot.

#"Select
#"Select

OK button to exit Multi Passes dialog box.

Depth cuts button and set the parameters to match the following screen shot.

#"Select

OK button to exit.

Page 6-37

TUTORIAL 6
#"Select

Lead in/out button and set the parameters to match the following screen shot.

#"Select
#"Select

OK button to exit.
OK button to exit Face contour parameters.

Page 6-38

TUTORIAL 6
STEP 17:
CROSS CONTOURING.
#"Rotate

the part by simultaneously pressing the Alt key and the left cursor key (%).
MAIN MENU
#"Toolpaths
#"Next Menu
#"C-axis
#"Cross ctr
#"Single
#"Select the contours as shown in the following picture.

Select the
last line
here

Select the
first line
here

Select the
third line
here
Select the
second
line
#"Done

Page 6-39

TUTORIAL 6
#"Get

a Flat End Mill from the library.

#"Select

Contour parameters page and make the necessary changes as shown in the
following screen shot.

Page 6-40

TUTORIAL 6

#"Select

OK button to exit parameters.

STEP 18:
FACE DRILLING.
MAIN MENU
#"Toolpaths
#"Next menu
#"C-axis
#"Face drl
#"Manual
#"Select the points as shown in the following picture, starting with Point 1 to Point 4.
( this will be the order in wich they will be machined)

Page 6-41

TUTORIAL 6

Select
Point 1

Select
Point 4

Select
Point 2

Select
Point 3
#"Press Esc to disable the checking.
#"Done
#"Righ-mouse click in the middle of the

white window and select Get tool from library.

Page 6-42

TUTORIAL 6
#"Select

the diameter Drill

#"Select

Simple drill no peck page and make the following changes.

$ Note that all parameters are incremental. This instructs the system to measure the
distances from the selected points z value.

Page 6-43

TUTORIAL 6

STEP 19:
CROSS DRILLING.
#"Cross drl
#"Manual
#"Select the

points as shown in the following picture, starting with Point 1 to Point 4.

( this will be the order in wich they will be machined)
Select
Point1

Select
Point 2

Select
Point 4

Select
Point 3

Page 6-44

TUTORIAL 6
#"Press Esc to disable checking.
#"Done
#"Get Drill from the library.

#"Select

Simple drill no peck page and change the parameters as shown in the
following screen shot.

Page 6-45

TUTORIAL 6
#"Select

OK button to exit parameters.

STEP 20:
C-AXIS CONTOURING.
#"C-axis
#"Single
#"Select

ctr
the contour as shown in the following picture.

Select the
arc here.

#"Done
#"Get a

1/16 Flat End Mill from the library.

Page 6-46

TUTORIAL 6

#"Select

Contour parameters page and change the parameters as shown in the

following screen shot.

#"Select

OK button to exit parameters screen.

Page 6-47

TUTORIAL 6

STEP 21:
CUTOFF THE PART.
#"Backup
#"Change Cplane to +DZ
#"Make sure that construction

depth Z=0

MAIN MENU
#"Toolpaths
#"Next Menu
#"Cutoff
#"[Select boundary point]: 5.5,-3.5

Page 6-48

TUTORIAL 6
#"Select

the same cutoff tool that we used for grooving.

#"Select

Cutoff parameters page and set parameters to match the following screen
shot parameters.

Page 6-49

TUTORIAL 6
#"Select OK button
#"Backup
#"Operations

to exit.

$Note that Lathe Cutoff operation has a locker icon and a message Do not update
stock. Click on the locker icon to disable it.
#"Select Regen path button to update the stock.

STEP 22:
VERIFY- TOOLPATH VERIFICATION
Select Verify
#"
Select Machine button.
#"

Select Machine

Page 6-50

TUTORIAL 6

The computer will now simulate the process of the part being machined.
The finished part should appear as shown in the following picture.

#"Select

stock section button to make a section through the part.

Select this icon to make a

section through the part

Page 6-51

TUTORIAL 6

#"Exit Verify.
Select this button to
exit Verify
#"Select OK to close Operation Manager.

Page 6-52

TUTORIAL 6
STEP 23:
POST THE FILE TO OBTAIN THE G-CODE FILE.
$ This tutorial covers Mastercams C-axis toolpath functionality. To apply these
toolpaths to a C-axis lathe, a customized post processor for your machine may be
required.
There are default C-Axis post processors included with Mastercam, such as
MPLFAN, MPLOKUHW, MPLTL3YC, MPLTL56T, AND MPLTPLSC. Due to the
variation in C-axis machine configurations contact your Mastercam reseller to
request post processor services such as C-axis post development.
Your post processor may require certain additional programming information not
covered in this tutorial. The nature of the additional information required depends
largely on your machines configuration. Contact the developer of your post
processor for details.
#"To

post the file please follow Step 9 of Tutorial #1 pag. 1-17 to 1-19.

STEP 24:
SAVE THE UPDATED MC8 FILE.
MAIN MENU
#"File
#"Save
#"Resave this drawing with the same name.
#"[ Delete old ] Yes

Page 6-53

TUTORIAL 6

Review Exercise

Page 6-54