Scribd
Upload
20 views4 pages

Sequence Impedence

Sequence Impedance

Uploaded by

Anonymous m65TTcfOT
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
20 views4 pages

Sequence Impedence

Sequence Impedance

Uploaded by

Anonymous m65TTcfOT
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Theory:

The sequence impedances of an alternator have differing values. This is because of


the difference in the effect of the armature m.m.f on the DC field m.m.f for different
sequences. They may be defined as:
Positive Sequence Impedance
It is the ratio of the fundamental component of armature voltage, due to the
fundamental positive sequence component of armature current, to this component of
armature current at rated frequency. This is the usual impedance (either
synchronous or transient or subtransient) of alternator.
Negative Sequence Impedance
It is the ratio of fundamental component of armature voltage, due to the
fundamental negative sequence component of armature current, to this component
of armature current at rated frequency
Zero Sequence Impedance
It is the ratio of fundamental component of armature voltage, due to the
fundamental zero sequence component of armature current, to this component of
armature current at rated frequency.
Procedure:
Positive Sequence Impedance (Xd" and Xq")
1. FIG.1. Apply a single-phase voltage to two phases (of the stator) in series of a
stationary star-connected alternator. Adjust the rotor position so that the current
due to the induced voltage in the short-circuited field winding is maximum.
Neglecting the resistance , Xd" will be :
Xd" = V/2I"
where I" is the current flowing through the two phase of the alternator with an
applied voltage V.
2. Turn the rotor through half pole pitch, q-axis will coincide with crest of the
armature m.m.f and the reactance offered by the armature would now be Xq".
3. For any rotor position, apply single-phase voltage across two windings in series
(say, phases A and B) and obtain the reactance V/2I". For the same rotor
position, repeat the test for phase B and C and then C and A in series. X1,X2
and X3 are he reactances obtained (X1 being maximum).Then,
Xd" = K-m
Xq"= K+m
where
K= (X1+X2+X3)/3

m =[ {(X1-K)2 + (X2-X3) 2 }/3]1/2


Negative Sequence Impedance (X2)
One possible method of measuring X2 is to run he machine at rated speed with its
field winding closed and to impress a balanced 3-phase voltage on the armature
terminals. Adjust the phase sequence of the voltage so that the current due to this
voltage in 3-phase armature windings sets up a rotating field in a direction opposite
to the direction of rotation of the machine. The negative sequence impedance is then
the ratio of impressed voltage and current per phase. A wattmeter connected in the
circuit will give the negative sequence resistance power loss and thus the value of
r2. The value of X2 can then be calculated.
FIG.2 gives the connection diagram for another method. Two phase A and B of the
star-connected alternator are short-circuited and voltage V is measured between C
and the junction terminals A and B. The machine is driven at rated speed. The
negative sequence impedance is then
Z2 = V/(3I)
The value of X2 can be obtained with the help of the wattmeter reading P, as
X2 =PZ2/(VI)
Short-circuit current is kept low so that the heating of he field system is within the
thermal capability of the machine.
Zero Sequence Impedance
Connect all the three phases of the armature winding in series and apply a reduced
voltage as shown in FIG.3. Drive the machine at rated speed with the field winding
short-circuited. Then,
X0=Z0= V/(3I) per phase.
Where I is the current through each winding.
Report:
Positive Sequence Impedance
X1= V/2I1 "=
X2= V/2I2 "=
X3= V/2I3 "=
K=(1/3)(X1+X2+X3)=
m = [ {(X1-K)2 + (X2-X3) 2 }/2]1/2
Xd" = K-m
Xq" = K+m
Negative Sequence Impedance
V=
I=
P=

Z2 = V/(3I)=
X2 =PZ2/(VI)=
Zero Sequence Impedance

V=
I=
X0=Z0= V/(3I)=
Result:
Xd" =
Xq" =
X2=
X0=

FIG.1

Positive Sequence Impedance

A
X

A1

230V
1-Phase
50Hz

V
N A2,B2,C2
B1
XX
C1

FIG.2

Negative Sequence Impedance

A
X

A1

P
230V
1-Phase
50Hz

N A2,B2,C2
B1
XX
C1

Rated Speed

FIG.3

Zero Sequence Impedance

A
X

B1

A2

A1

P
230V
1-Phase
50Hz

B2

V
XX
C2

Rated Speed

You might also like