Huawei Basic

1.
To Check the Number of HSDPA User allocated per cell:

LST UCELLCAC-----in RNC end
2. To Check the SCTPLNK & SAAlLNK:
LST UIUBCP:
3. LST OP
ADD OP (For Creating Account in RNC/BSc for Local login during M2000 Connecti
vity down)
4 IRAT:3G to 2G handover
Network reselection :2G to 3G handover.
5. LST Unode---To get node-B all info in RNC end
6. DSP UCELL---To check the status of Node-B cell(Result---Cell is Setup and ena
bled)
DSP UCELLCHK---to check traffic in RNC end
BLK UCELL---to Block cell in RNC
DEA UCELL--To Deactivate Cell in RNC.
ACT UCELL--To Activate Cell in RNC
UBL UCELL----To UBlock Ucell in RNC
BLK Unode-B----To Block Unode-B in RNC
UBL Unode-B----To Unblock Unode-B in RNC
RST Unode-B----to Reset Unode-B in RNC
PING IP--------To ping the Node-B Service from RNC
TRC IPADDR------To check where we are getting drop in RNC
LST UCELL------To get information about the Cell like PSC,Frequency,Transmitting
Power,LAC,SAC,RAC in RNC
LST UPCPICH------To check pilot channel power
MOD UPCPICHPWR----To Change Pilot Channel Power in RNC.
LST UINTRAFREQNCELL------Use this command to query the intra-frequency neighbori
ng cell.
ADD UINTRAFREQNCELL---- to add neighbour Cells (IntraFreq)
LST UEXT3GCELL-----------List the information of neighboring RNC cells.
ADD UEXT3GCELL----To Add the 3G cells(Other Vendors) as external cells.
ADD UEXT2GCELL----To Add the 2g Cells As external Cells
ADD U2GNCELL------To add the 2G Neighbour Cells
dsp usrnum----Hsdpa Throughput per subrack
LST PHBMAP---To Check the Service Priority
To Change the Node-B Name in RNC:
1.MOD UNODEBNAME
2.MOD ADJNODE
To Change the Node-B Name in Node-B end
1.MOD SITE
2.SET NODEBNAME
LST DEVIP----To check the RNC Board IP.
LST ETHIP----To Check the Ethernet port IP.
LST ALMAF----To check the RNC Alarm
DSP E1T1---To check the E1T1 of Site in RNC end.
LST VER---To check the Software Version of RNC.
DSP OMU----To check the OMU Status in RNC.
DSP OMUHW---To check the Status of ETH port.
LST License---To check the License file loaded in RNC & Active license.
DSP LICUSAGE---To check the feature activated in the License.
LST UCELLHSDPA----To check whether the HSDPA feature is Activated or Not.
LST UCELLHSUPA----To check whether the HSUPA feature is Actiavted or not
DSP ELABEL:to Check the item Code of Boards
LST UAC----To Check the LAC & RAC.
MOD UCELLLACINFO----To Change LAC,RAc,SAC for Cell.
Node-B
REQ CMCTRL----request CM control for an LMT user
FOC CMCTRL-----to forcibly obtain the NE Configuration Management (CM) control w
hen the M2000 retains CM control after obtaining it.

LST DEVIP----To Check what are the IP defined in Node-B
RST BRD---to reset the board
RST NODEB---To reset the whole node-B
BLK BRD--to block board
BLK LOCELL---To block CELL.
DSP VSWR----to check VSWR.
ADD DEVIP---to add the Devip in Node-B
ADD IPRT---- To add the Iproute in node-B.
LST RRU----to Check the RRU Number,RRU work Standard
LST RRUCHAIN----- To Check the Chain Number,WBBP board Subrack no,Slot Number.
MoD LOCELL-----to Change the Frequecy number,transmitting power.
LST LOCELL----to check the Local cell id,Cell ID.
LST SEC--to Check the Sector Type
LST RXBRANCH---To check the Attenuation
MOD RXBRANCH----To Modify the attenuation.
LST ALMAF-------To check the Alarm in Node-B end.
LST VER-------To check the Software version.
LST NODEBNAME---To check the Correct Configuration file is loaded or not,Nodeb N
ame normally will be the Site Name.
PING---To do ping test in Node-B end.
TRACERT---To Check,is there any drop in IP(Useful to check transmission having p
roblem)
LST IPCLKLNK---To check the IPClock IP address.
DSP IPCLKLNK---to Check the Status of IPCLK.
LST ALMPort---To check the External Alarm Configuration.
SET ALMPort---to Define the External Alarm in Node-B end.
SET ENVALMPARA----To define the External Alarm Name.
LST ETHPORT -------To check the ETHport Configurtion
SET ETHPORT-------To Configure the ETHport
DSP TIME-----To check the Current time in Node-B
SET TIME----To Set the Correct time
DSP LICENSE----To check License is loaded or not.
DSP CELLCFG----To check the Scrambling code (PSC)
ULD File-------To upload the Log File
DSP SFP---to Check the SFP module type & output power
Site Down Alarm
NCP,CCP Alarm
SCTP,SAALNK.
NodeB Unavailable
Sector Down:
Locell unusable.
Cell Setup Failed

Huawei Basic

Uploaded by

Copyright:

Available Formats

Huawei Basic

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Huawei Basic

Uploaded by

Copyright:

Available Formats

1.

To Check the Number of HSDPA User allocated per cell:

hen the M2000 retains CM control after obtaining it.

You might also like