Paice cli coli earl} Principles of Control NO elo] U. A. Bakshi V. U. Bakshi Technical Publications Pune”Table of Contents : Chapter-1 Basics of Control System (1-1) to (1-24) Chapter-2 Basics of Laplace Transform (2-1) to (2-20) Chapter-3 Transfer Function and impulse Response (3-1) 10 (3 -38) Chapter-4 Block Diagram Representation (41) to (4 -74) Chapter-§ Signal Flow Graph Representation (6 =1)t0 (5 -70) Chapter-6 Mathematical Modeling of Systems (6-1) to (6 -46) Chapter-7 Time Response and Feedback Characteristics (7-1)to (7- 132) Chapter-8 Stability Analysis (8-1) to (8-48) Chapter-§ Root Locus (9- 1) to (9 - 88) Chapter - 10 _ Basics of Frequency Domein Analysis (10- 1) to (10 -26) Chapter-11 Bode Plot (11 1) to (11 - 84) Chapter -12 Polar and Nyquist Plots (12- 1) to (12-90) Chapter - 13 _Nichol's Chart (13- 1)t0 (13-14) Chapter - 14 Compensation of Control Systems (14-1) to (14 -50) Chapter - 15 _ Control System Components (15-1) to (15-60) Appendix -A_ Miscellaneous Questions (A= 1) to (A -22) Features of Book '# ‘The important concepts are highlighted using Key Point throughout the book. | i The stepwise methods suggested to explain the various complicated topics, made} | the understanding of the subject very easy. ' \# The use of clear, informative and to the scale graphs, plats and atsereetis, ' Best of Technical Publications As per Revised Syllabus of Mumbai University - 2007 Course Semester-V [E & Te] Environmental Studies Bagad = Principles of Control Systems Bakshi = Signals and Systems Chitode © Microprocessors and Microcontrollers - 1 Godse 4)=e Principles of Control Systems ISBN 9788184316841 Al rights reserved with Technical Publications. No port ofthis book should be reproduced in any form, Electronic, Mechanical, Photocopy or any information storage and retrieval system without prior permission in writing, from Technical Publications, Pune. Published by : - Technical Publications Pune” ‘#1, Amit Residency, 412, Shaniwat Peth, Pune - 411 030, India Printer : Avert DTPrinters Seno. 10/3 Sinhagod Rood, Pre 411041Preface The importonce of Principles of Control Systems is well known in vorious engineering fields. Overwhelming response to our books on various subjects inspired us to write this book. The book is structured to cover the key aspects of the subject Principles of Control Systems. The book uses plain, lucid language to explain fundamentals of this subject. The book provides logical method of explaining various complicated concepts and stepwise methods to explain the important topics. Each chapter is well supported with necessary illustrations, practical examples and solved problems. All the chapters in the book are arranged in a proper sequence that permits each topic to build upon earlier studies. All care has been taken to make students comfortable in understanding the basic concepts of the subject. The book not only covers the entire scope of the subject but explains the philosophy of the subject. This makes the understanding of this subject more clear and makes it more interesting. The book will be very useful not only to the students but also to the subject teachers. The students have fo omit nothing and possibly have to cover nothing more. We wish to express our profound thanks to oll those who helped in making this book a reality. Much needed moral support and encouragement is provided on numerous occasions by our whole families. We wish to thank the Publisher and the entire team of Technical Publications who have token immense pain to get this book in time with quality printing. Any suggestion for the improvement of the book will be acknowledged ond well appreciated Authors UW. A. Bakshe D.U. Bakshi Dedicated to Guraraj, Aparoa, Arjun. WEAR iCopyrighted material(1-1) to (1-24) 1.1 Background. 1.2 Definitions ; 1.3 Classification of Control —— a 1.4 Open Loop System .. 7 rr 1-8 1.42 Disadvantages. nian TER ie | 1.4.3 Real Time Applications of an Open Loop System . 1-8 1.4.3.4 Sprinkler used to Water 2 Lawn 1-8 1.4.3.2 Stepper Motor Positioning System... . . . sane see 18 1.4.3.3 Automatic Toaster System be aan wees “18 1.4.3.4 Traffic Light Controller... cee ee ee 18 1.4.3.5 Automatic Door Opening and Closing System a a mn H8 1.5 Closed Loop System ... 1.5.1 Advantages. 1.5.2 Disadvantages . cecteeeeeees 1.5. RealTime Applications of Closed Loop System, cctvsmeunconices semsecisce TM 1.5.3.1 Human Being . 4-14 1.5.3.2 Home Heating System. Hwa ma ws fe eM 1.5.3.3 Ship Stabilization System... . see ee 112 1.5.3.4 Manual Speed Control System sewn tol? 1.5.3.5 D.C. Motor Speed Control i 1-13 1.6.3.6 Temperature ControlSystom. 2. . ee 14 41.5:3.7 Missile Launching System. . 1-14 1.5.3.8 Voltage Stabilizer. 1-14 1.6 Comparison of Open Loop aid Closed ep Control System .. Ww)1.7 Servomechanisms ... 1.8 Regulating Systems (Regulators) .... 1.9 Feedback and Feed Forward System 1.9.1 Real Time Application of Feed Forward System ........ 00. cece eee e eee 1219 1.10 Multivariable Control Systems. University Question. Chapter -2_ Basics of Laplace Transform 2.1 Background... 2.2 Definition of Laplace Transform...... 2.3 Properties of Laplace Transform... 2.3.4 Linearity . 2.3.2 Scaling Theorem . 2.3.4 Real Integration. ... 2.3.5 Differentiation bys........ 2.3.6 Complex Translation sin 2.3.7 Real Translation (Shifting Theorem) . . 2.3.8 Initial Value Theorem. 2.3.9 Final Value Theorem 2.4 Inverse Laplace Transform 2.4.1 Simple and Real Roots 24.2 Multiple Roots ........... ‘ 2.4.3 Complex Conjugate Roots. . 2.5 Use of Laplace Taner in Control ‘Sysiom 2.6 Special Case of Inverse Laplace Transform Examples with Solutions ... Chapter-3 Transfer Function and Impulse Response 3.1 Background... 3.2 Concept of Transfer Function .. 3.3 Transfer Function..3.3.1 Definition. ...... — 3 3.3.2 Advantages and Features of Transfer Function 3 3.3.3 Disadvantages... eee ee Sysaeeiant 3.3.4 Procedure to Determine the Transfer Function of a Control System 3 3.4 Impulse Response and Transfer Function..... 3.5 Some Important Terminologies Related to the T-F. 3-10 3.5.4 Poles of a Transfer Function ...... 3-10 3.5.2 Characteristic Equation of a Transfer Function ....... 2... eee 3-11 3.5.3 Zeros of a Transfer Function......0......... ee 3-11 3.5.4 Pole-Zero Plot. RaRecnaeNNNERNELAcNRNRaRN apesynacsesaneii aie 3.5.6D.C.Gain....... 3.6 Laplace Transform of Electrical F NsROHE. 3.7 State Variable Models 37.1 Concept of State. 3.7.2 Important Definitions. . . 3.8 State Model of Linear idler, 3.8.1 State Model of Single Input Single Output System. 3.9 State Variable Representation using Physical Variables . 3.9.1 Advantages. . 3.10 Dynamic Raaparise of, Secu: idee Electrical syetent i Examples with Solutions Review Questions... University Question... Chapter -4 Block Diagram Representation (4-4) to (4-74) 4.1 Background... sod 4.1.1 Illustrating Concept of Block Diagram Representation ........ sarees ay MO 44.2. Advantages of Block Diagram 4-4 4.1.3 Disadvantages ....... 0... ese mere 4-4 4.2 Simple or Canonical Form of Closed Loop Hot water Desired _ > Actual temperature temperature Pressure thermometer Fig. 1.21 1.5.3.7 Missile Launching System This is sophisticated example of military applications of feedback control. The enemy plane is sighted by a radar which continuously tracks the path of the aeroplane. The launch computer calculates the firing angle interms of launch command, which when amplified drives the launcher. The launcher angular position is the feedback to the launch computer and the missile is triggered when error between the command signal and missile firing angle becomes zero. The system is shown in the Fig. 1.22. 1.5.3.8 Voltage Stabilizer Supply voltage required for various single phase appliances must be constant and high fluctuations are generally not permitted. Voltage stabilizer is a device which accepts variable voltage and outputs a fixed voltage.Principles of Control Systems 1-15 Basics of Control System rg ames Actual position Launch computer LP Feedback Power amplifer Fig. 1.22 Missile launching system Principle of such stabilizer is based on controlling number of secondary turns as per requirement to increase or decrease the output voltage. The actual output voltage is sensed by a transformer and potential divider arrangement. The reference voltage is selected proportional to the desired output level. The actual output is compared with this to generate error which in turn is inputted to the controller. The controller takes the proper decision to increase or decrease the number of turns so as to adjust the output voltage. The scheme is shown in the Fig. 1.23. To load constant voltage Controller and relays ale Reference Isolation transformer voltage Fig. 1.23 Voltage stabilizerPrinciples of Control Systems 1-16 Basics of Control System The other examples of closed loop system are machine tool position control, positioning of radio and optical telescopes, auto pilots for aircrafts, inertial guidance system, automatic electric iron, railway reservation status display, sunseeker solar system, water level controllers, temperature control system. So in closed loop feedback control systems cause and effect relationship between input and output exists. 41.6 Comparison of Open Loop and Closed Loop Control System Sr. Open Loop Closed Loop No. 1. | Any change in output has no effect on the| Changes in output, affects the input which is input ie. feedback does not exists. possible by use of feedback. 2. | Output measurement is not required for} Output measurement is necessary. operation of system. 3. Feedback element is absent. Feedback element is present. 4. | Error detector is absent. Error detector is necessary. 5. | it's inaccurate and unreliable. Highly accurate and reliable. 6. Highly sensitive to the disturbances. Less sensitive to the disturbances. 7. Highly sensitive to the environmental changes.| Less sensitive to the environmental changes. 8. | Bendwidth is small. Bandwidth is large. 9. | Simple to construct and cheap. Compicated to design and hence costly 10. | Generally are stable in nature. Stability is the major consideration while designing 11. | Highly affected by nonlinearities. Reduced effect of nonlinearities. 4.7 Servomechanisms Definition : It is a feedback control system in which the controlled variable or the output is a mechanical position or its time derivatives such as velocity or acceleration. A simple example of servomechanism is a position control system. Consider a load which requires a constant position in its application. The position is sensed and converted to voltage using feedback potentiometer. It is compared with input potentiometer voltage to generate error signal. This is amplified and given to the controller. The controller in turn controls the voltage given to motor, due to which it changes its positionPrinciples of Control Systems 1-17 Basics of Control System ‘The scheme is shown in the Fig. 1.24. + Field current constant Error voltage | AMP: Gears Load Referencd ‘Actual postion position Input a a SS Feedback potentiometer potentiometer Fig. 1.24 Position control system Few other examples of servomechanisms are, 1) Power steering apparatus for an automobile. 2) Machine tool position control. 3) Missile launchers. 4) Roll stabilization of ships. 1.8 Regulating Systems (Regulators) Definition : It is a feedback control system in which for a preset oalue of the reference input, the output is kept constant at its desired value. In such systems reference input remains constant for long periods. Most of the times the reference input or the desired output is either constant or slowly varying with time. In a regulator, the desired value of the controlled outputs is more or less fixed. Similarly the reference input is also fixed and called set point. Thus the regulator maintains a constant output for a fixed reference input. The problems due to disturbances are mainly rectified by the regulator. A simple example of such regulator system is servostabilizer. We have seen earlier that in voltage stabilizer position of tap on secondary is adjusted by using relay controls. But instead of fixed tap, the entire secondary can be smoothly tapped usingPrinciples of Control Systems 1-18 Basics of Control System a servomotor drive, The servomotor drives the shaft and controls the position of tap on secondary as per the controller signal. Due to the fluctuations in the main input if the load voltage changes, such effects are rectified by the regulator to keep load voltage constant. ‘The actual scheme is shown in the Fig. 1.25, while its block diagram representation is shown in the Fig. 1.26. Controlled Main signal Input 9 stabilised voltage Feedback Feedback _ Etro: alk [--®@: ; Reference input Isolation transiormer Fig. 1.25 Regulating system Reference voltage ‘Actual load voltage Load voltage sensing Fig. 1.26 Few other examples of regulating system are, 1) Temperature regulators. 2) Frequency controllers. 3) Speed governors.aa You have either reached a page that is unavailable for viewing or reached your viewing limit for this book.Basics of Control System ‘Controller Temperature sensor Feedback Constant temperature required Heat exchange Fig. 1.28 Feedback system for temperature control Practically if the rate of flow of metal from tank to heat exchanger gets disturbed, due to change in level then the temperature gets affected. But it takes a long time to see its effect at the output to take the corrective action. Key Point: In feedback system, the corrective action can not be taken unless and until output gets disturbed. Due to the time lag, it is not possible to keep the output temperature constant within limits. Valve Contaller ¥ Feedback signal J Temperature sensor Feed forward signal Constant ‘Outer ™Perature == (2) Feed forward system Flow meter <== Feed forward Heal exchanger} Disturbance (change in flow rate) Reference input > 7 (X)-+] controller Valve Temperature sensor == Feedback Constant temperature (0) Block diagram Fig. 1.29 Practical example of feed forward systemPrinciples of Control Systems 1-21 Basics of Control System In such a case, feed forward system is used. The inlet flow rate is measured with the flowmeter. Immediately when there is a change in rate of flow, it is indicated to the controller through flowmeter before it disturbs the output. The controller takes the corrective action inadvance by adjusting the steam flow. Thus the output temperature gets maintained constant within the limits. Key Point : The feed forward compensation, compensates the effect of disturbance before it actually disturbs the output The system is shown in the Fig. 1.29 (a) while its block diagram representation is shown in the Fig. 1.29 (b). The feed forward minimizes the transient error due to measurable disturbances. While feedback compensates for unmeasurable disturbances and other effects. Thus it is advisable to incorporate both feedback and feed forward schemes in a system. 1.10 Multivariable Control Systems The control system in which there is only one output of the interset is called single variable system. But in many practical applications more than one variables are involved. A control system with multiple inputs and multiple outputs in called a multivariable system. The block diagram representation of a multivariable control system is shown in the Fig. 1.30. The part of the system which is required to be controlled is called plant. The controller provides proper controlling action depending on the reference inputs. There are n reference inputs Ty, Ty, sso Tae Control signals 4 Plant [-y——+ tp Controller or + & (Analog or digital) d System tobe A controlled en Feedback elements Fig. 1.30 Block diagram of multivariable control system There are n output variables c,(W), C2(t),-.---Cn(t). The values of these variables represent the performance of the plant. The control signals produced by the controller are applied to the plant. With the help of feedback elements the closed loop control of the plant is also possible. Due to the feedback, the controller takes into account the actual output values to decide the control signals.Principles of Control Systems 1-22 Basics of Control System In case of multivariable systems, sometimes it is observed that a single input considerably affects more than one outputs. The system is said to be having strong interactions or coupling. This coupling is nothing but the disturbances for the separate systems. The interactions inherently present between inputs and outputs can be cancelled by designing a decoupling controller. Thus the resulting multivariable system is considered to have proper number of single input single output systems and the controller is designed for each system. The another way is to design a controller which will take care of all the inherent interactions present in the multivariable system. In multivariable linear control system, cach input is independently considered. Only one input and one output is considered and the total effect on any output because of all the inputs acting simultaneously is determined by addition of the outputs due to each input acting alone. Thus law of superposition is used to analyse multivariable linear control systems. In many practical control systems, control is achieved by more than one input and the system may have many outputs. In chemical processes simultaneous control of pressure, temperature and concentration is required by commanding various inputs. Air crafts and space crafts are other examples where movement is controlled by various inputs. Power generators, atomic reactors and jet engines are some of other examples of multivariable systems. Consider the block diagram of multivariable autopilot system shown in the Fig. 1.31. Cortrol Angular signal position Reference inputs Digital to analog converter Digital controller =| Actuator Rocket Vehicte Position feedback Analog to digital converter ‘Acceleration feedback Fig. 1.31 Multivariable autopilot systemPrinciples of Control Systems 1-23 Basics of Control System The system shown in the Fig. 1.31 keeps a track of rocket vehicle in response to reference inputs given to it. The position, velocity and acceleration of the vehicle are fed to the digital controller using motion sensors. The controller takes appropriate decision and sends a controlling signal which will drive the actuator, which will move the engine. Thus there are three output variables which are to be observed and controlled and there are corresponding reference inputs hence the system is multivariable system. Review Questions 1. Define the following terms (i) System Gi) Control system Git) Input Gio) Output (0) Disturbance, Explain how the control systems are classified Define linear and nonlinear control systems. 4, What is time variant system? Give suitable example. How it is different than time in variant system? 5. Define open loop and closed loop system by giving suitable examples. 6. Differentiate between open loop and closed loop systems giving suitable examples. 7. With reference to feedback control system define the following terms (i) Command input (ii) Reference input (ii) Forward path (ie) Feedback path 8. Differentiate between (i) Linear and Nonlinear systems G0 Continuous and Diserete data systems 9. Explain what is closed loop contro! system, giving examples. 10. What is seroomechanism? State its exempl 11. Distinguish between feedback control system and feed forward control system. 12._Write a note on multivariable control systems. University Question 1. Compare open-loop and closed loop control system. (MU : Dec.-2007, 5 Marks) Qa0a(1 - 24)Basics of Laplace Transform 2.1 Background The various methods used to solve the engineering problems are based on the replacement of functions of time by certain frequency dependent variables. This makes the computation job very easy. The known example of such method is the use of Fourier series to solve certain electrical problems. The transformation technique relating the time functions to frequency dependent functions of a complex variable is called the Laplace transformation technique. Such transformation is very useful in solving linear differential equations. The transfer function of a system, which is heart of the control system analysis is based on the Laplace transform. This chapter gives the definition of Laplace transform, some commonly used functions and Laplace transform pairs and useful properties of Laplace and inverse Laplace transform. Some examples are also included demonstrating the superiority of Laplace approach over the conventional approach. 2.2 Defi jition of Laplace Transform The Laplace transform is defined as below : Let f(t) be a real function of a real variable t defined for t > 0, then F(s) = {f(b} = ft).en* dt o Where F(s) is called Laplace transform of f(t). And the variable ’s' which appears in K(s) is frequency dependent complex variable. It is given by, s = otjo Where o = Real part of complex variable ‘s’. @ = Imaginary part of complex variable “s’. The time function f(t) is obtained back from the Laplace transform by a process called Inverse Laplace transform and denoted as L“!. Thus, (2-1)Principles of Control Systems 2-2 Basics of Laplace Transform L* [F(S)] = LIL} = £0 The time function f(t) and its Laplace transform F(s) is called transform pair. yup Example 2.1: Find the Laplace transform of e~* and 1 for t 2 0. Sol @ f® = F(s) = Li) = Jee dt = [ene dt a ~ 1 a = feeat gee |— “sajt - fe at [ Gray * | -1 1 = 0 =) = ora Lest} = and ara (i) f(t) = 1 Fs) = fimmes dt a L{1} = and 2.3 Properties of Laplace Transform Number of important properties of the Laplace transform are discussed in this section. The table of Laplace transform pairs is developed using these properties. 2.3.1 Linearity The transform of a finite sum of time functions is the sum of the Laplace transforms of the individual functions. So if (3), F(s), F, (3) are the Laplace transforms of the time functions f(t), fy (1), sonra f(t) respectively then, Lif ()) + f(t) + ct £, (OE = F(s) + Fy(s) + - + F,(s) The property can be further extended if the time functions are multiplied by the constants ie. L fay f(t) + ag tlt) + wut agia(B | = ayFy(S) + agF(5) + wnt a gE (9) Where aj, a»,.. a,, are constants.Principles of Control Systems 2-3 Basics of Laplace Transform 2.3.2 Scaling Theorem If K is a constant then the Laplace transform of Kf(t) is given as K times the Laplace transform of f(t). [--————_—— LIK fb} = K Fis) | ~. Kis constant 2.3.3 Real Differentiation (Differentiation in Time Domain) Let F(s) be the Laplace transform of f(t). Then, {| = s Hs) (0-) Where { (07) indicates value of f(t) at t = 0~ i.e. just before the instant t = 0 The theorem can be extended for n'* order derivative as, ul a 7c 8" F(s)—s®-! (0-)—s™-2 £0" )- K— F@-) (O-) Where f'°~" (0-) is the value of (n ~ 1)" derivative of f(t) at t = 0°. ie for n = 2, {em = s? F(s)-sf(0-)- £'@ ) 3 uf = = s3K(s)-s2f(0-)-sf’(0-)= £”(0- ) and so on. This property is most useful as it transforms differential time domain equations to simple algebraic equations, alongwith the initial conditions, if any. 2.3.4 Real Integration If F(s) is the Laplace transform of f(t) then, L {Jeo} = Fe) ‘ This property can be extended for multiple integrals as, f f nee sl f(Odt, dt, a,|=8 ao 4Principles of Control Systems 2-4 Basics of Laplace Transform 2.3.5 Differentiation by s If F(s) is the Laplace transform of f(t) then the differentiation by s in the complex frequency domain corresponds to the multiplication by t in the time domain. F(s) L{t ho} d Thus, Ly = Litt =-4 wim=- Lit?) = Litxt} = 2.3.6 Complex Translation If F(s) is the Laplace transform of f(t) then by the complex translation property, F(s-a) = Le* fn} and F(s +a) = Lfe*'f()} Fis ma) = Fis) Where F(s) is the Laplace transform of f(t). 2.3.7 Real Translation (Shifting Theorem) This theorem is useful to obtain the Laplace transform of the shifted or delayed function of time. If F(s) is the Laplace transform of f(t) then the Laplace transform of the function delayed by time T is, L{ f-T} = eT F(s) 2.3.8 Initial Value Theorem The Laplace transform is very useful to find the initial value of the time function {(t). Thus if F(s) is the Laplace transform of f(t) then, £(0*) = Lim f(t) = Lim s F(s) tor we The only restriction is that f(t) must be continuous or at the most, a step discontinuity att=0.Principles of Control Systems 2-5 Basics of Laplace Transform 2.3.9 Final Value Theorem Similar to the initial value, the Laplace transform is also useful to find the final value of the time function f(t). Thus if F(s) is the Laplace transform of f(t) then the final value theorem states that, Lim ft) = Lim sF(s) The only restriction is that the roots of the denominator polynomial of F(s) i.e. poles of F(s) have negative or zero real parts. wm Example 2.2 : Find the Laplace transform of sin ot. Solution : The sin at can be expressed using Euler's equation as, . ettce sin ot = Se L{sinat} = 2 .. Using Linearity property an 1 aye do Ue) = Now Ue") = ty and Ue} = L{sinet} = __o +0 L{sinot} = © +oPrinciples of Control Systems 2-6 Basics of Laplace Transform Table of Laplace Transforms : f(t) Fis) Waveform - : te oO K T t Constant K : K |_o | K f(t, K is constant K F(s) 1 ' 3 t 0 e i ova od 1 =a emi sin ot cos wt (arta e* cosat (sta) (tartar sink wt cosh ot sto Table 2.1 Standard Laplace transform pairPrinciples of Control Systems 2-7 Basics of Laplace Transform Function fit) Laplace Waveforms Transform F(s) Unit step = u(t) 1 8 A u(t) “A 3 Delayed unit step = u(t — T) Ault ~T) Aet 1 . ‘er oT Unit ramp = r(t) = t u(t) if “| Se Slop 0 Atul) A ' 2 Slope =A 0 Delayed unit ramp = r{t - T) = (tT) u(t - T) gl 1 = A siope = 1 oT A(t=T)ut=1) ' fs Slope =A, oT Unit impulse = 3(t) 1 7 | 4 ‘to 20Principles of Control Systems 2-8 Basics of Laplace Transform =) Delayed unit impulse Impulse of strength K i.e. K 5(t) K Table 2.2 Laplace transforms of standard time functions 2.4 Inverse Laplace Transform As mentioned earlier, inverse Laplace transform is calculated by partial fraction method rather than complex integration evaluation. Let F(s) is the Laplace transform of £(t) then the inverse Laplace transform is denoted as, Ft) = L'[F(s)] The F(s), in partial fraction method, is written in the form as, = NG) 9 = D6) Where N(s) = Numerator polynomial in s and D(s) = Denominator polynomial in s Key Point: The given function F(s) can te expressed in partial fraction form only when degree of N(s) is less than D(s). Hence if degree of N(s) is equal or higher than D(s) then mathematically divide N(s) by D(s) to express Fis) in quotient and remainder form as, Fs) = Q+R(s) = +N) ~ 2°06) Where Q = Quotient obtained by dividing N(s) by Dis) and H(s) = NO) ~ remainder Dis)les of Control Systems 2-9 Basics of Laplace Transform Now in the remainder, degree of N‘(s) is less than D’(s) and hence F,(s) can be expressed in the partial fraction form. Once K(s) is expanded interms of partial fractions, inverse Laplace transform can be easily obtained by adjusting the terms and referring to the table of standard Laplace transform pairs (Table 2.1). The roots of denominator polynomial D(s) play an important role in expanding the given F(s) into partial fractions. There are three types of roots of D(s). The method of finding partial fractions for each type is different. Let us discuss these three cases of roots of Dis). 2.4.1 Simple and Real Roots The roots of D(s) are simple and real. Hence the function F(s) can be expressed as, N(s) _ NG) F(s) = DG) @=aye-b)G-6) Where a, b, c K are the simple and real roots of D(s). The degree of N(s) should be always less than D(s). This can be further expressed as, N(s) HEHE F(s) Z Where K,, K,, K;, ... are called partial fraction coefficients. The values of K,, K,, K, ... can be obtained as, K, = (s-a).As)},_, K, = (sb). Fs), K, = (s-¢)- Rs), In general, K, = (s-s,)- FQ)... and so on. Where s, = 1 root of D(s) L{ew*} = Gad is standard Laplace transform pair. Hence once F(s) is expressed interms of partial fractions, with coefficients K,, K, K K,, the inverse Laplace transform can be easily obtained. f(t) = L'[F(s)]=K, e* +K, e+ K, et +KPrinciples of Control Systems 2-10 Basics of Laplace Transform mp Example 2.3: Find the inverse Laplace tran m of given F(s). (s+2) Fl = Gra Solution : The degree of N(s) is less than D(s). Hence F(s) can be expressed as, F(s) = A + a + Ge 6 SErH, Caer 3 K, = = (s+ 4) ( i = y3 2 (#3) (s+4) Taking inverse Laplace transform, fi) = gt gem Sew 2.4.2 Multiple Roots The given function is of the form, re) = —NO)__ (s~ a)" Ds) Here there is multiple root of the order ‘n’ existing at s = a. The method of writing the partial fraction expansion for such multiple roots is, a Where a represents remaining terms of the expansion of F(s). Key Point: Thus a separate coefficient is assumed for each power of repetative root, starting from its highest power n to 1 Here find the LC.M. of the entire right hand side and express numerator interms of Ky .K, .K2,-.. The numerator N(s) on left hand side is known. Compare the coefficients ofPrinciples of Control Systems 2-11 Basics of Laplace Transform all powers of s in the numerator of both sides which will give simultaneous equations interms of Ky,.K,.K;,... Solving these equations we can obtain the coefficients Ky 5K, Ky, For ease of solving simultaneous equations, we can find out the coefficient Ky by the same method as discussed for simple roots. Ky = (s-a)" FG) Similarly coefficients for simple roots present if any, can also be calculated by the method discussed earlier, for ease of solving simultaneous equations. While finding Laplace inverse transform of expanded F(s) refer to standard transform pairs, yey = 2 Les? ts] = PL and re wy = —BL (s+ay" -a) mm Example 2.4: Obtain the inverse Laplace trausform of given Fis). Fig) = 2-2) s(s+ 1)’ Solution : The given F(s) can be expressed as, Fe) = S02 + AL "tl G+) Finding L.C.M. of right hand side, ) Ko ()# Ky + I s+ s(s+ 1) s(s+ 1)? s.(S—2) = Kgs+K, s?+K,s+K,s° +2K,s? +K,s+K,s> +3K,57+3K,s+K, Comparing coefficients of various powers of s on both sides, For s3, K,+K, = 0 KQ) For s?, K,+2K,+3K, = 0 KQ) For st, K@) For s°, K@) As from (1), ©. from (2), 2. from (3), Ky = 3Principles of Control Systems 2-12 Basics of Laplace Transform Fa = 35+ 3, G+ G+) Now ered =< he +a)" mif{—t |. ett Gay a! 1 1 1 1 Fs) = 3. 2. 42.2 -2.5 ©) ey @y @+) s {) = L" [F(s)] = et tr 2et-2 fl) = Ziel aatet +2et-2 2.4.3. Complex Conjugate Roots If there exists a quadratic term in D(s) of F(s) whose roots are complex conjugates then the F(s) is expressed with a first order polynomial in s in the numerator as, AstB | NYS) (s? +us+B) Ds) F(s) Ne) De) represents remaining terms of the expansion. The A and B are partial fraction coefficients. Where (s? +as +f) is the quadratic whose roots are complex conjugates while The method of finding the coefficients in such a case is same as discussed earlier for the multiple roots. Once A and B are known then use the following method for calculating inverse Laplace transform, As+B = A and B are known st+astB Consider (s) = Now complete the square in the denominator by calculating last term as, LT = Where LT = Last term M.T = Middle term RT = First termPrinciples of Control Systems 2-13 Basics of Laplace Transform LT. FG) Where o Now adjust the numerator As +B in such a way that it is of the form, —9__ Lie coset] = ete (rato (aye Ue sin wt] = Key Point: Thus inverse Laplace transform of F(s) having complex conjugate roots of D(8), always contains sine, cosine or damped sine or damped cosine functions. mm) Example 2.5: Find the inverse Laplace transform of sh+3 (s? + 25+ 5)(o+ 2) Solution : The given F(s) can be written as, AstB | C si+2s+5 st2 Fs) = Fis) = Ass? +2s+5 has complex conjugate roots. To find A, B and C find L.C.M. of right hand side, + 2)(As+B)+C re = & (AS + B)+ C(: (s? +284 5)(s+2) _ _ As? +2 As+ Bs+ 2 B+ Cs? + 280+ 5C (s? + 2s+ 5)(s+ 2) (s? + 28+ 5) (s+ 2) Comparing the coefficients of various powers of s, of the numerators of both sides s?+3 = s?(A+C)+s(2A+ B+ 2C)+(2B+5C) A+C =1 K() 2A+B+2C = 0 K (2) 2B+5C = 3 K@)Principles of Control Systems 2-14 Basics of Laplace Transform To solve the equations quickly, the coefficient C corresponding to the simple, real root can be obtained as, (2 C = F(s).(s+2),_ ais | (443) 3... “G85 Substituting in equation (1) and (2), & Ae 5 and B= Ks) = —S—— Consid F(s) = —2—— ‘onsider i(s) anes 2[_ ss (s+ 1)? #(2) split 4 as 2x 2 2 stl z 22 42x? _ tts +0) (st) (2) Rey = 24_ OF) _ a > |(s# I)? +2)" (s+ 1)? +(2) As ra [ee s| = [e"coswt] and sta) +or ara = fe“ sinat] (sta)? +o Hence taking inverse Laplace transform of F(s), f(t) = -2 let cos2t+2e°t sin 2t1+7 e®Principles of Control Systems 2-15 Basics of Laplace Transform 2.5 Use of Laplace Transform in Control System The control systems can be classified as electrical, mechanical, hydraulic, thermal and so on. All systems can be described by integrodifferential equations of various orders. While the output of such systems for any input can be obtained by solving such integrodifferential equations. Mathematically, it is very difficult to solve such equations in time domain. The Laplace transform of such integrodifferential equations converts them into simple algebraic equations. All the complicated computations then can be easily performed in s domain as the equations to be handled are algebraic in nature. Such transformed equations are known as equations in frequency domain, Then by eliminating unwanted variable, the required variable in s domain can be obtained. Then by using technique of Laplace inverse, time domain function for the required variable can be obtained. Hence making the computations easy by converting the integrodifferential equations into algebraic is the main essence of the Laplace transform, imp Example 2.6 : Obtain the expression for y(t) which is satisfying the differential equation 2 we oft) + 8 ylt) = 16e"!, Neglect initial conditions, dt? Solution : Taking Laplace transform of both sides of the given differential equation and @ Ea 4 ay) neglecting initial condition terms in Laplace transform of “Ys we get, s2Y(s} + 6sY(s) + 8Y(s) = a (6? + 68+ 8) Y(s) = wp WO» Gayetrers Ys) = soetset Yo = Sit seta Taking inverse Laplace transform of Y(s), y(t) = 5.33e' - Be + 266e# This is the required solution of differential equation.Control Systems 2-16 Basics of Laplace Transform 2.6 Special Case of Inverse Laplace Transform Let us see now if the order of P(s) and Q(s) of the function F(s) is same. In such case P(s) must be divided by Q(s), to obtain the seperation of F(s) as a constant term which is result of the division and the remainder polynomial P'(s) having order less than Q(s). P(s) So Fs) = Be «Order of P(6) and Q(s) same Ps) ~ a) Now Laplace inverse of constant term is impulse function. Refer last pair in the Table 2.2 LIK) = K8(t) where 8(t) = unit impulse. While P's) / Q(s) can now be expressed to obtain partial fraction expansion, to get its inverse very easily. Note : The same method is to be applied F(s) with order of numerator polynomial P(s) is greater than denominator polynomial Q(s) 4185? +3845, 3348s? 4175410, ym) Example 2.7: Find the Laplace inverse of F(s) Solution : Divide P(s) by Q(s). s8+8s?+17s+10) s°+1857+ 3s + 5 (1>K 34 824175 +10 103? Fs) = 1+ 08-9 _ () = My ry aste17e+10 ote Mvs3 2, A Be ©" 6¥2) G41) G5)" s#2 "S41 545 40s? 148-5 a= eS 2-21 B 10s? -14s-5 +2) G45 10s?—14s 5 | c~ gaye . eePrinciples of Control Systems 2-17 Basics of Laplace Transform 24.75 , 26.25 He) = 1- S33 sat 35 f(t) = L? {F(s)} = S(t)- 21 e° *+4.75 e-' +26.25e°* Where Ir1 {1} = 8(®) = Unit impulse function Examples with Solutions im Example 2.8 : In the circuit given, the values of R and C are 1MQ and 1 uF respectively, Obtain the expression for the current flowing in the circuit if it is supplied with an input of step voltage of 1 V at t = 0. | Step of +> + avattz0 oe po Fig. 2.4 Solution : Let us write down the equation for the circuit given, assuming supply voltage as v(t). Po] vt) wD Fig. 2.1(a) Applying Kirchhoff's voltage law we get, v(t) = qQR+ aco) dt Where voltage across capacitor is 2 fi() dt While v(t) = Step of 1 V at t = 0 as shown in the Fig. 2.1(b). Taking Laplace transform of both sides of above equation,Principles of Control Systems 2-18 Basics of Laplace Transform vs) = 1)R +2[2] 5 Neglecting initial conditions hence neglecting the term of initial condition in Laplace transform of J i(t) dt. Now Vis) = 1 as v(t) is step of 1 V .. Refer pair 1 in Table 22 ' 0 (s)R+ =z Ils) 1 te9[R + | 1 _ Ks)[1+sRC} " 5 sc ¢ é 16) = Tere * ; We) = * ste Taking Laplace inverse, referring Table 2.1 . 1. =a i(t) = Rre* Substituting values of R and C, t iw = 1 Tx 108 1 10-6 y= —L. 1 = sa0% it) = Ix10S et A Key Point: It can be observed in this example that solving the equation in time domain for the current, involves calculation of complementary function, then particular integral and arbitrary constants, independently. In Laplace approach we get the answers of all in a single step. Hence Laplace approach proves io be superior over a normal approach.Principles of Control Systems 2-19 Basics of Laplace Transform imp Example 2.9 : A series circuit consisting of resistance R and an inductance of L henry is connected to a supply of x(t) volts. Find the expression of the current in s domain. Also calculate the value of current at t isa step voltage of 50 V. Neglect initial condition. Solution : The circuit is shown in the Fig. 2.2. R Applying KVL we get, _— wo = re ut) ne dt Taking Laplace and neglecting initial conditions of current we get, Fig. 2.2 Vis) = U(s)R + Lsl(s) V(s) = Ks) {R + sL] Ks) = 3 ee 50 Now R=1x103@ — L= 25x10°H and V(s) = > 1) = 50 Ks) = —— Us) = - A = 005 and B= - 0.05 Ks) = ——- ‘Taking inverse Laplace transform, i(t) = 0.05 - 0.05 #14" A 1) = 005 (1-e 8) A At t = 0.5 msec = 0.5x 10 sec i) = 045 (er 98s05500°9)) it) = 0.05 A. 0.5 msec with R = 1x 10° Q, L = 25 mH and supply Taking 25x10 outside ... Partial fractions Qo0a(2 - 20)Transfer Function and Impulse Response 3.1 Background The mathematical indication of cause and effect relationship existing between input and output means to decide the transfer function of the given system. It is commonly used to characterize the input-output relationship of the system. Transfer function explains mathematical function of the parameters of system, performing on the applied input in order to produce the required output. Laplace transform plays an important role in making mathematical analysis easy. Laplace transform and its use in control system analysis is thoroughly discussed in Chapter-2. In this chapter concept of transfer function, transfer function models and impulse response models of the systems are discussed. 3.2 Concept of Transfer Function In any system, first the system parameters are designed and their values are selected as per the requirement. The input is selected next, to Selection of designed system. This is v shown in the Fig. 3.1 sewaed Now performance of input ‘System parameters Output the system can be 5 expressed interms of its Fig. 3.1 output as, Output = Effect of system parameters on the selected input Output = Input x Effect of system parameters, Output Input Effect of system parameters = (8-1)aa You have either reached a page that is unavailable for viewing or reached your viewing limit for this book.Principles of Control Systems 3-3 _Transfer Function and Impulse Response and vo(t) = af i(t) dt 2) Vas vo where V,(s} is Laplace of v,(t) and V;(s) is Laplace of v;(t) and initial conditions are to be neglected. We are interested in So taking Laplace of above two equations and assuming initial conditions zero we can write, 1 V,(s) = RI(s)+ Is) (3) V,(6) = 416) ~@) é Is) = sCV, (s) Substituting in equation (3), Vis) = scvyio]R~ +] Vi(s) = sCR V,(s) +V,(s) = V,(s)[1+ sCR] Vols) 1 Vi) 1+sCR We can represent above system as in the Fig. 3.4, which is called transfer function model of the system. vis) 1 Vols) " 1+sRC ° Fig. 3.4 mp Example 3.2: Find out the TF. of the giver network. R L Pe eat) xo ) Po Fig. 3.5 Solution : Applying KVL we get the equations as,Principles of Control Systems 3-4 Transfer Function and Impulse Response E = Re Leh f it (a) input = E, ; output = E Laplace transform of f f(t) dt = . Neglecting initial conditions and Laplace transform of i = sks) ... Neglecting initial conditions Take Laplace transform, Es) = Is) [Re sk+ I W) 2 A Be [Rest <| Now zs idt » 3) E,) = ells) ° xc I) = SCE) ~@ Substituting value of I(s) in equation (2), SCE) 2 EO” [Resteg 1. -__ 4 «[xes+F] RsC+ s?LC+1 sC So we can represent the system as in the Fig. 3.6. E\s) EQ(s) Fig. 3.6 Transfer function model 3.3.2 Advantages and Features of Transfer Function The various features of the transfer function are, i) It gives mathematical models of all system components and hence of the overall system. Individual analysis of various components is also possible by the transfer function approach.Principles of Contro! Systems 3-5 Transfer Function and Impulse Response ii) As it uses a Laplace approach, it converts time domain equations to simple algebraic equations. iii) It suggests operational method of expressing equations which relate output to input. iv) The transfer function is expressed only as a function of the complex variable ‘s’. It is not a function of the real variable, time or any other variable that is used as the independent variable. v) It is the property and characteristics of the system itself. Its value is dependent on the parameters of the system and independent of the values of inputs. In the example 3.1, if the output ie. focus of interest is selected as voltage across resistance R rather than the voltage across capacitor C, the transfer function will be different. So transfer function is to be obtained for a pair of input and output and then it remains constant for any selection of input as long as output variable is same. It helps in calculating the output for any type of input applied to the system. vi) Once transfer function is known, output response for any type of reference input can be calculated. vii) It helps in determining the important information about the system i. poles’, zeros, characteristic equation etc. viii) It helps in the stability analysis of the system. ix) The system differential equation can be easily obtained by replacing variable ‘s' by d/dt. x) Finding inverse, the required variable can be easily expressed in the time domain. This is much more easy than to analyse the entire system in the time domain. 3.3.3 Disadvantages The few limitations of the transfer function approach called approach are, i) Only applicable to linear time invariant systems. ii) It does not provide any information concerning the physical structure of the system. From transfer function, physical nature of the system whether it is electrical, mechanical, thermal or hydraulic, cannot be judged. iii) Effects arising due to initial conditions are totally neglected. Hence initial conditions loose their importance.Principles of Control Systems 3-6 _Transfer Function and Impulse Response 3.3.4 Procedure to Determine the Transfer Function of a Control System ‘The procedure used in Example 3.1 and Example 3.2 can be generalized as below : 1) Write down the time domain equations for the system by introducing different variables in the system. 2) Take the Laplace transform of the system equations assuming all initial conditions to be zero. 3) Identify system input and output variables. 4) Eliminating introduced variables, get the resultant equation interms of input and output variables. 5) Take the ratio of Laplace transform of output variable to Laplace’ transform of input variable to get the transfer function model of the system. mp Example 3.3: Find out the T.F. of the given network. Fig. 3.7 Solution : Applying KVL we can write, e@ = L J i() dt + (QR we (1) an dt while et) = (RK 2) where e\(t) = Input and e,(t) = Output Taking Laplace of equations (1) and (2), neglecting the initial conditions. . 116) E\(s) = sls) + @ = + RIB) ail) E,(s) = I(s)R (4)Principles of Control Systems 3-7 Transfer Function and Impulse Response E,(s) = 16) [sus Example 3.5 : The Laplace inverse of the transfer function in time domain of a certain system is e~** while its input is rit) = 2. Determine its output c(t). Solution : Let T(s) be the transfer function L1[Ts)] = Ti)=e* given Wt) = 2 But e(t) # x(t) x T(t), It is mentioned earlier that ea = T(t) is not at all valid in time domain, so c(t) # 20%. Hence the equation valid according to the definition of transfer function must be used, C Te) = Ho so Tis) = LIT) = Lie} = 4, Ris) = was r(t) = 1 = s+5 Cs) = 2sPrinciples of Control Systems 3-10 _Transfer Function and Impulse Response Taking Laplace inverse of this equation, c(t) = 04-04 0 Output 3.5 Some Important Terminologies Related to the T.F. As transfer function is a ratio of Laplace of output to Laplace of input and hence can be expressed as a ratio of polynomials in ‘s’. PG) TE = OG This can be further expressed as, The numerator and denominator can be factorised to get the factorised form of the transfer function as, rp = Kis-s.)(6~s0)- 81) (S— 52) where K is called system gain factor. Now if in the transfer function, values of ‘s’ are substituted as s; $2.83...) in the denominator then value of TLR. will become infinity. 3.5.1 Poles of a Transfer Function Definition : The values of ‘s’, which make the T.F. infinite after substitution in the denominator of a T.F. are called ‘Poles’ of that T.F. So values 8 , $3 ,S3...-.-5q are called poles of the T.F. These poles are nothing but the roots of the equation obtained by equating denominator of a T.F. to zero. For example, let the transfer function of a system be, The equation obtained by equating denominator to zero is, s(s+4) = 0 s=0 andPrinciples of Control Systems 3-11.__Transfer Function and Impulse Response If these values are used in the denominator, the value of transfer function becomes infinity. Hence poles of this transfer function are s = 0 and ~ 4. If the poles are like s = 0, - 4, -2, 45, ..... ie. real and without repeated values, they are called simple poles. A pole having same value twice or more than that is called repeated pole. A pair of poles with complex conjugate values is called pair of complex conjugate poles. 2s +2) Sa Re 0) = GHP este) ‘The poles are the roots of the equation (s+ 4)? (s? + 28+ 2) (s+ 1) = 0. + Poles are s = -4,-4,-14j1,-1 So T(s) has simple pole at s=-L Repeated pole at s = -4, (two poles) Complex conjugate poles at s= -l+jl Key Point: Poles are indicated by ‘X’ (cross) in s-plane. 3.5.2 Characteristic Equation of a Transfer Function Definition : The equation obtamed by equating denominator of a T.F. to zero, whose roots are the poles of thai T.F. is called characteristic equation of that system F(s) = bys" + bjs" 1+ bys"? + +b, =0 is called the characteristic equation. 3.5.3 Zeros of a Transfer Function Similar to the poles, now if the values of ‘s’ are substituted ass, , Sp numerator of a LR, its value becomes zero, -+8, in the Definition : The values of 's’ which make the TF. zero after substituting in the numerator are called ‘zeros’ of that TF. Such zeros are the roots of the equation obtained by equating numerator of a T.F. to zero. Key Point: Zeros are indicated by a smull circle ‘o” in s-plane. Poles and zeros may be real or complex-conjugates or combination of both the types. Poles and zeros may be located at the origin in s-plane. Similar to the poles, the zeros also are called simple zeros, repeated zeros and complex conjugate zeros depending upon their naturePrinciples of Control Systems 3-12 Transfer Function and impulse Response 2(s +1)? (s + 2) (s? + 2s +2) “* TOS SDE) This transfer function has zeros which are roots of the equation, 2(s+ 1)? (s+ 2)(s? +2s+2) = 0 ie. Simple zero at s = -2 Repeated zero at s = -1 (twice) Complex conjugate zeros at s = -1 + jl The zeros are indicated by small circle or zero ‘o’ in the s-plane. 3.5.4 Pole-Zero Plot Definition : Plot obtained by locating all poles and zeros of a TE. in s-plane is called pole-zero plot of a system. 3.5.5 Order of a Transfer Function Definition : The highest power of ‘s’ present in the characteristic equation i.e. in the |denominator polynomial of a closed loop transfer function of a system is called ‘Order’ of a system, 3.5.6 D.C. Gain The value of the transfer function obtained for s = 0 i.e. zero frequency is called the d.c. gain of the system. D.C. Gain = T(s)|,- 9 Key Point It is not possible to indicate the value of d.c. gain on pole-zero plot as it is a constant value, It is required to be separately specified, alongwith the pole-zero plot The d.c. gain decides the resultant constant of the system transfer function. Imaginary For example, consider example 3.1 discussed earlier. The system T.F. is T+sRC RG Real So 1 + sRC = 0 is its characteristic equation and system is first order system Then s =~ 1/RC is a pole of that system and T.F. has no zeros. Fig. 3.9Principles of Control Systems 3-13 Transfer Function and Impulse Response The corresponding pole-zero plot can be shown as in the Fig. 3.9. Similarly for example 32, the T-F. calculated is, 1 1/L¢ th - 1+ __. s?LC+ sR =0 woganen So system is 2nd order and the two clesinre; Be (RY (1 Ps * or * y (a0 ite Real TLE. has no zeros. Pda) Pole Now if values of R, L and C selected are such that both poles are real, unequal and negative, the corresponding pole-zero Fig. 3.10 plot can be shown as in the Fig. 3.10. For a system having TF. as, Cs) _ +2 RG) ~ sis? +2s+ 2Is? +75+ 12] The characteristic equation is, s(s?+2s+2)(s?+7s+12) = 0 ie. System is 5th order and there are 5 poles. Poles are 0,-1.4), -3, -4 while zero is s(s? +2s+2) (s+ 3) (st+4) =0 located at —2' The corresponding pole-zero plot can be drawn as shown in the Fig. 3.11. Imaginary RealPrinciples of Control Systems 3-14 _Transfer Function and Impulse Response After getting familiar with introductory remarks about control system, now it is necessary to see how overall systems are represented and the methods to represent the given system, based on the transfer function approach. 3.6 Laplace Transform of Electrical Network In the use of Laplace in electrical systems, it is always easy to redraw the system by finding Laplace transform of the given network. Electrical network mostly consists of the parameters R, L and C. The various expressions related to these parameters in time domain and Laplace domain are given in the table below. Element Time domain Laplace domain Laplace domain expression for voltage | expression for voltage | behaviour Resistance R eR KeR R Inductance ait) sli(s) st Capacitance © Ayia at ts) ef Table 3.1 From the table it can be seen that after taking Laplace transform of time domain equations, neglecting the initial conditions, the resistance R behaves as R, the inductance behaves as sL, while the capacitance behaves as +, and all time domain functions get sc converted to Laplace domain like i(t) to I{s), v(t) to V(s) and so on. By using these transformations, the parameters can be replaced by their Laplace transform to get Laplace transform of the entire network. Once this is obtained, simple algebraic equations relating Laplace of various voltages and currents can be directly obtained. This eliminates the step of writing the integrodifferential equations and taking Laplace of them. e.g. Consider a network shown below, elt)Principles of Control Systems 3-15 Transfer Function and Impulse Response The Laplace of the above network can be obtained by following replacements. R>R L> sL 1 R; > Ry C4 ge e(t) > E\(s) e,(t) 3 E,(s) The other variables then can be R ~ introduced which will be directly | > ——awy—/00i9-___-__—o Laplace variables to obtain the | 1 (3) ) re we Fels) Laplace domain equations directly. 18) Such Laplace of network is shown in the Fig. 3.13. ——n—> Fig. 3.13 3.7 State Variable Models Consider a football match. The score in the football match must be updated at every instant from the knowledge and information of the total score before that instant. This procedure of updating the score continues till the end of the match when we get exact and precise score of the entire match. This updating procedure has main importance in the understanding of the concept of state. 3.7.1 Concept of State Consider the network as shown in the Fig. 3.14 To find V,.., the knowledge of the initial { capacitor voltage must be known, Only information about V,, will not be sufficient Vn QR Vout a bout Vin | to obtain precisely the V,,, at any time t2 0. Such systems in which the output is not only dependent on the input but also on the initial conditions are called the systems with memory or dynamic systems. While if in the above network capacitor 'C is replaced by another resistance “R,' then output will be dependent only on the input applied Vin, Such systems in which the output of the system depends only on the input applied at Zero fiction t= 0, are called systems with zero memory or Fig, 3.15 static systems.aa You have either reached a page that is unavailable for viewing or reached your viewing limit for this book.Principles of Control Systems 3-17 Transfer Function and Impulse Response initial conditions. So state can be defined as vector X(t) called state vector. This X(t) ie. state at any time ‘t' is ‘n’ dimensional vector ie. column matrix n x 1 as indicated below. XH) X(t) X(t) = X(t) Now these variables X,(t), X2(t), called the state variables of the system. If state at t = t, is to be decided then we must know X(ty) and knowledge of the input applied between ty — t,. This new state will be X(t,) which will act as initial state to find out the state at any time t > t,. This is called the updating of the siate. The output of the system at t = t, will be the function of X(t) and the instantaneous value of the input at t= t, if any. The number of the state variables for a system is generally equal to the order of the system. The number of independent state variables is normally equal to the number of energy storing elements (e.g. : capacitor voltage, current in inductor) contained in the system. .. X(t) which constitute the state vector X(t) are 3.7.2 Important Definitions 1) State : The state of a dynamic system is defined as a minimal set of variables such that the knowledge of these variables at t = to together with the knowledge of the inputs for t > to, completely determines the behaviour of the system for t > to. 2) State Variables : The variables involved in determining the state of a dynamic system X(t), are called the state variables. X,(t), X(t), ....Xq(t) are nothing but the state variables. These are normally the energy storing elements contained in the system. 3) State Vector : The ‘n’ state variables necessary to describe the complete behaviour of the system can be considered as “n' components of a vector X(t) called the state vector at time “t’. The state vector X(t) is the vector sum of all the state variables. 4) State Space : The space whose co-ordinate axis are nothing but the ‘n’ state variables with time as the implicit variable is called the state space. 5) State Trajectory : It is the locus of the tips of the state vectors, with time as the implicit variable. Definitions can be explained by considering second order system : Order is 2 so number of state variables required is 2 say X;(t) and X2(0). State vector will be the matrix of order 2 x 1.Principles of Control Systems 3-418 Transfer Function and Impulse Response _ pay X(t) = [xo = 3 ie, X(t) = Xi(t)+ Xp(t) (vector addition) The state space will be a plane in this case as the number of variables are two. Thus state space can be shown as in the Fig. 3.16. xt) x4) Xofl 0.9) x Fig. 3.16 Now consider t = t,. > > > XH) = 1 (ty) + X(t) x(t) State trajectory Xott) X(t) X alta) Fig. 3.18 Fig. 3.19 Now consider t > > 3 Xit2) = X(t) + Xa(t2) The state trajectory can be shown by joining the tips of the two state vectors i.e. X(t,) and X(t). 3.8 State Model of Linear Systems Consider multiple input multiple output, n' order system as shown in the Fig. 3.20. Number of inputs = m Number of outputs. =pPrinciples of Control Systems 3-19 Transfer Function and Impulse Response uy [1 U2 MIMO. rT Y2 Inputs | SYSTEM | Outputs Um L }_t—~ v, Ky Xp My Xn Stale varlables Fig. 3.20 fue Xi) ¥,(®) Unt) X2(t) ¥2(0 u@ =|] o: [x=] : |. vos Unit) x, (0) Y.) Alll are column vectors having orders m x1, n x 1 and p x 1 respectively. For such a system, the state variable representation can be arranged in the form of “n first order differential equations. Po = Xt) = fy Oy Xz pceeeXq /Up Up in) It BX) X(t) = fy Oly pXp peep Uy Up oe dt ao = Kaiad Cl Rien Key ty, « where f =| : | is the functional operator f, Integrating the above equation, t Xi€Q = Xilta) + Pf Op Xz eee Ny Uy Up ones Um) at %oPrinciples of Control Systems 3-20 Transfer Function and Impulse Response where i = 1, 2, Thus ‘n’ state variables and hence state vector at any time “t' can be determined uniquely. Any ‘n’ dimensional time invariant system has state equations in the functional form as, X= 1%) While outputs of such system are dependent on the state of system and instantaneous inputs. ©. Functional output equation can be written as, Y(t) = g(X, U) where *g’ is the functional operator. For time variant system, the same equations can be written as, X(t) = AX, U, 8... State equation Yo @(X U, t) .... Output equation Diagramatically this can be represented as in the Fig. 3.21. U() Instantaneous input X(t) Initial state Fig. 3.21 Input-output state description of a system The functional equations can be expressed interms of linear combination of system states and the input as, Xi = ayy Xp Fay Xp Fo tay Xq t Dy Uy + By Up te + Dig Um Xo = ayy Xp + agg Xp vee + Ay Xq + by Uy + by Up +. + Bay Up M M Kn = ag Xp + agg Xp t eve + gg Xq + By Uy + Bag Up + «e+ + Dam U,Principles of Control Systems 3-21 Transfer Function and Impulse Response For the linear time invariant systems, the coefficients a, and by are constants. Thus all the equations can be written in vector matrix form as, Xt) = AX() +B UG) where X(t) = State vector matrix of order n x 1 U() = Input vector matrix of order m x 1 A. = System matrix or evolution matrix of order n x n B = Input matrix or control matrix of order n x m Similarly the output variables at time t can be expressed as the linear combinations of the input variables and state variables at time t as, YD = C1 XO) # es + Cay Malt) + diy Url) + «+ + dim Unt) M M Gp Xa) + one + Gyn Xalt) + dy Ul) + 2 + dy Uy f pm For the linear time invariant systems, the coefficients ¢j and dj are constants, Thus all the output equations can be written in vector matrix form as, pi Y(t) =C X(t) + D U(t) where Y(t) = Output vector matrix of order p x 1 c D Output matrix or observation matrix of order p x n Direct transmission matrix of order p x m The two vector equations together is called the state model of the linear system. Xt) = A Xi) + BUD State equation Yt) = CX() + D UC) Output equation This is state model of a system. For linear time-variant systems, the matrices A, B, C and D are also time dependent. Thus, XW) = AW X +B UO| For tinear time variant system YW) = C(t) X(t) + Dit) UL)Principles of Control Systems 3-22 Transfer Function and Impulse Response 3.8.1 State Model of Single Input Single Output System Consider a single input single output system ie, m = 1 and p = 1. But its order is 'n’ hence n state variables are required to define state of the system. In such a case, the state model is XQ = AX + BUH Y(t} = C X(t) +d UH where A = nxn matrix, B=n x 1 matrix © = 1x n matrix, d = Constant and U(t) = Single scalar input variable In general remember the orders of the various matrices. A = Evolution matrix =nxn B = Control matrix =nxm C = Observation matrix spxn D = Transmission matrix => p x m 3.9 State Variable Representation using Physical Variables The state variables are minimum number of variables which are associated with all the initial conditions of the system. As their sequence is not important, the state model of the system is not unique. But for all the state models it is necessary that the number of state variables is equal and minimal. This number 'n’ indicates the order of the system. For second order system minimum two state variables are necessary and so on. To obtain the state model for a given system, it is necessary to select the state variables. Many a times, the various physical quantities of system itself are selected as the state variables. For the electrical systems, the currents through various inductors and the voltage across the various capacitors are selected to be the state variables. Then by any method of network analysis, the equations must be written interms of the selected state variables, their derivatives and the inputs. The equations must be rearranged in the standard form so as to obtain the required state model. Key Point: It is important that the equation for differentiation of one state variable should not involve the differentiation of any other state variable. In the mechanical systems the displacements and velocities of energy storing elements such as spring and friction are selected as the state variables.Principles of Control Systems 3-23 Transfer Function and Impulse Response In general, the physical variables associated with energy storing elements, which are responsible for initial conditions, are selected as the state variables of the given system. wm) Example 3.6: Obtain the state model of the given electrical system Fig. 3.22 Solution ; There are two energy storing elements Land C. So the two state variables are current through inductor i(t) and voltage across capacitor ie. v¢(t)- XO = i and X(t) = v(t) And UW) = v(t) = Input variable Applying KVL to the loop, ai(t) v(t) = i) R+L “ai + volt) Arrange it for di(t)/dt, dit) 1 R 1 dit) _ y SO = tv w-Bin-ty. bur = Rw . R 1 1 ie. Kt) = - EX O-EXO+E UO call) While v(t) = Voltage across capacitor = & fic) at ava) 1 av (t) “oO = Lit bur Se ie. XW = 2x0 +2) The equations (1) and (2) give required state equation. a Ro 1 [09] a! DE [iol cue Xa(t) | & of Pa) | ie. XW) = A X(t) + BUI)Principles of Control Systems. 3-24 Transfer Function and Impulse Response While the output variable Y(t) = vg(t) = Xa(t) 4 Yo) = 0 4 [x J+ uo ie 0) C X(t) and D = [0] This is the required state model. As n = 2, it is second order system. Note : The order of the state variables is not important. X,(t) can be v,(t) and X,(t) can be i(t) due to which state model matrices get changed. Hence state model is not the unique property of the system. 3.9.1 Advantages The advantages of using available physical variables as the state variables are, 1. The physical variables which are selected as the state variables are the physical quantities and can be measured. vy ‘As state variables can be physically measured, the feedback may consists the information about state variables in addition to the output variables. Thus design with state feedback is possible. 3. Once the state equations are solved and solution is obtained, directly the behaviour of various physical variables with time is available. But the important limitation of this method is that obtaining solution of such state equation with state variables as physical variables is very difficult and time consuming. 3.10 Dynamic Response of Second Order Electrical System Consider a second order electrical system R Ls oe shown in the Fig.3.23 (a). Let us find the f f Laplace domain network of this circuit as wo veld shown in the Fig 3.23 (b). The initial conditions are zero. As obtained in the Ex. 3.2, | 4 Vols) _ a: ___1/ie =5 = = Vi) S?LC#sRC+1 oe Bse th To obtain the dynamic response, assume that the input to the system is unit step input u(t) where u(t) = 1 fort 2 0. » v() = u(t) hence V\(s) = Lol=! Fig. 3.23 (b)Principles of Control Systems 3-25 —_Transfer Function and Impulse Response 1 1/Le - Ic | Reg 1 f2,R 1 [t+Estre| s(stetseze] Hence, V,(s) = V;(s) By partial fractions, V,(s) = + a Z eRe The dynamic response is obtained by taking inverse Laplace transform of V,(s). Vo) = ETA) = LE a oe Seb stig The dynamic response depends on the nature of roots of the equation oR bog "Te equation are, This is the characteristic equation of the network. The roots of this R RY 1 S12 -- ata) “te The dynamic sesponse depends on the nature of the roots of this equation which ultimately depends on the values of R, L and C of the network. If both the roots are real, unequal and negative say - a and ~ b then the dynamic response becomes, vo(t) = A+Ben*+Cett This is purely exponential. If both the roots are real, equal and negative say — a and ~ a then the dynamic response becomes, vol) = A+Bte*+Cen® This is exponential and fastest of all the exponential responses. If both the roots are complex conjugates with negative real part as - a jb then the dynamic response becomes, v(t) = A+Ber“ sin (bt+0) This is damped oscillatory response. If both the roots are purely imaginary as 0+jb then the dynamic response becomes, volt) = A+Bsin (bt) This is purely sinusoidal in nature.Principles of Control Systems 3-26 Transfer Function and Impulse Response Key Point: The dynamic response of second order system depends on the nature of the roots of its characteristic equation. The Fig. 3.24 shows the various possible dynamic responses of a second order system. Output ‘Damped Oscillations (complex conjugate Tools with negative real part) Final value Exponential (unequal, real and negative roots) ‘Exponential (equal, real and negative roots) t of Fig. 3.24 Dynamic response of second order system Examples with Solutions imp Example 3.7 : The transfer function of a system is given by, _ K(s+ 6) ~ s(8+ 2)(S+5) (8? + 75+ 12) Determine i) Poles ii) Zeros iii) Characteristic equation and iv) Pole-zero plot in s-plane. Solution : i) Poles are the roots of the equation obtained by equating denominator to zero ie. roots of, (s+ 2) (845) (s? +784 12) = Imaginary ite. s(s + 2) (5 +5) (5 + 3) (s+ 4)=0 So there are 5 poles located at s = 0, - 2, -5,-3and -4 Real ii) Zeros are the roots of the equation obtained by equating numerator to zero ie. roots of K (s + 6) = 0 ies =-6 There is only one zero. Fig. 3.25Principles of Control Systems 3-27 __Transfer Function and Impulse Response iii) Characteristic equation is one, whose roots are the poles of the transfer function. So itis, s (5 +2) (5 +5) (2 +7s+12) = 0 ie. s(s? +7s+10)(s2+7s+12) = 0 ie. so 41454 +713 4154s? +1208 = 0 iv) Pole-zero plot This is shown in the Fig. 3.25 nm Example 3.8: The unit impulse response of a system is given by Tit) = e~ (1-cos 2t) Determine its transfer function, Solution : Laplace transform of the impulse response is the transfer function. T(s) = L {T(t} = Lfe' (1-cos 2t)} = L fet} - L fe“! cos 2t} 1 ___@+i) d+) stl @+1)?+Q)? stl (5? +2545) a (s+ 1) (9? +2845) T cos mmm Example 3.9: Find the transfer function ae of a system having differential equation given below. dct) , dct) Te te TO + rt) Solution: Taking Laplace transform of the given equation and assuming, all initial conditions zero we get, 2s*C\s) + 25C(s) + Cl) = R(s)+ 2e™* RG) Laplace transform of delayed function is, Lif(t-T) = est FS) (Refer Table 2.2) L{r(t-1)) = e 1 R(s) Combining terms of C(s) and R(s) we get, (2st +2s+1)C(s) = RG) (1+2e°5) Cls)__ 1428 RS) 2524+ 2s+1Principles of Control Systems 3-28 ‘Transfer Function and Impulse Respons: mp Example 3.10 : Find V,(s) / V,(s). Assume gain of buffer amplifier as 1. 1 uF 0.5 pF w(t) ampifier Fig. 3.26 Solution : Taking Laplace transform of the network, 1 1 —— oem sxtx1o0® 3x 0.5 x10 Buffer 6 anne rx? a |Vols) 6 Vs} 1x10 2 Fig. 3.27 Let us divide the network into two parts, Part 1: 468) Fig. 3.28 Applying KVL, Vis) Its) + 1x 106 Ks) (1) aon Rees sxIxl0-* V,(s) = 1x 108 Kis) + (2)Principles of Control Systems 3-29 Transfer Function and Impulse Response = 16) \S) = Ta08 een eae 10° 10° +5 10°] [ V,(s) Substituting equation in (1) Vj(s) = [+ 10°} -| es [oe Vis) _ os VQ) > s+T Part 2: 6 4 = 2x10 sx05 x10 s | vas) > txto’a — |Vols) 1(s) {____§ Fig. 3.29 2x10° Vils) = Is) z +1x10° -() V,(s) = Ms)1 x108 = Q) _ V.(s) 6) = he Substituting in equation (1), _ VS) [248], 06 Vx(s) = ae a | Vols) _ _s. Vis) +2 Now gain of buffer amplifier is 1 (unity) Vi(s) = Vals) s _ +2) (Sy)v@ = ve 2 MAG) s tl Vie) ~ G62)Principles of Control Systems 3-30 Transfer Function and impulse Response mp Example 3.11: Determine the transfer function if the dic. gain is equal to 10 for the system whose pole-zero plot is shown belovw. Imaginary Real Fig. 3.30 Solution : From pole-zero plot given, the transfer function has 3 poles at s = -1, -2+j and -2-j. And it has one zero at s = ~ 3. . K(s+ 3) MS) = @EH@tIeper2—p K(s+3) © (+H (6+27 =H (+ 1) [s? +4845] Now dc. gain is value of T(s) at s = 0 which is given as 10. dic. gain = T(s)|ts-0 Kx 3 10 = a6 50 Ke= 3 = 16.667 Te = 1866763) (s+ 1) (s? +4545) This is the required transfer function.Principles of Control Systems 3-31 Transfer Function and Impulse Response wm Example 3.12 : If the system transfer function is Y(s) st+4 X() ~ 58 42845 Obtain the differential equation representing the system. Ys) __ _s+4 Solution ; wn = aosSt eee XG) ~ S?42545 (s° +2845) Y(s) = (8 + 4) X(s) s? Y(s) + 2s Y(s) +5Y(s) = 5X(s) + 4X(5) Replacing variable s by 4 and Y(s) by y(t) and X(s) by x(t) we get, a d d gee O42 Sy) + 5y) = exit) + Axtt) ... Differential equation > Obtain the state model of the electric network as shown in Fig. 3.31 Ly ty 4 TOOT OT [Lem Input = Ey Ry Sep = Output | | Fig. 3.34 Solution : The various currents are as shown in the Fig. 3.31 (a) Fig. 3:31 (a)Applying KVL to loop I and Il, dl, - Urge 7 Ver Er =0 dy 1 Hcp YetEe And E, = LR, Select state variables as, I = X, ly = Xy Vc= X; and input E, = U and output E, = Using in the equations (1), (2), (3) and (4). : 1 L R= opportu X = o a 1 % = E%-E% and Y= %)R X = AX+BU 1 0 0 =e alo -& 1 where aslo ot ar 1 a ° of Control Systems 3-32 ransfer Function and Impulse Response Y=CX +DU J. aT 0 |,C=[0 R, 1 (1) (2) ~-) 01, D = [0]‘inciples of Control Systems 3-33 Transfer Function and impulse Response nm Example 3.14 : For the netzoork of figure 3.32 below find the transfer function ed (MU : Dec.-2003, 2005) Fig. 3.32 Solution : The s-domain network is shown in the Fig. 3.33. Applying KVL to the two loops, -R, L(s)-I,(s) sL+1,(s) sL+ Vis) = 0 ie. Ty(s) [Ry +SL]=Ih(s) SL = Vis)... (1) =Ia(6) Ro ~E. Ta(s) “SL Ia (0)+SL1,(8) = 0 Fig, 3.33 1 iyo 1o[R.+eest = yee SCHL SLC 6 “he -—— iL 29) “ate wee (2) Using @) in (1), 2LC+sR,C+1 tao] ESC) [R, +SL]-I,(6)sL = Vos) 2 4 a = Vis) Lc Ls) _ se Vis) ~ SLCR, +5 R)R,C#R, + 9CC48°L RC sks LC 1) s?LC Vis) s?LC (R; +Ry)+s(R,R,C+L) +R, mmm Example 3.15: Obtain the transfer function of the lag network shown. IMU : Dec.-2006, May-2008]Principles of Control Systems 3-34 Transfer Function and Impulse Response Ry po | Fig. 3.34 : Taking Laplace transform of the network Applying KVL to the network , E,G)=R l6)+ Ls+I9R, 0) 2) E,(5) = Ells) + Rp 16) = Q) “E,(s) = te| e+ R= 2 1 f ac | CE, Fig. 3.35 * Is) = at Substituting in (1), E,(s) = CEs) aS] T#sCR, sc 1+8CIR, +Ral = Eel) 75 SCR, Es) _ __1+s8CRy E@) ~ T#sC{Rp+Rai ‘mp Example 3.16 : Obtain the transfer function of the lead network shown below. (MU : May-2006] a) c Ry ent)Principles of Control Systems 3-35 Transfer Function and Impulse Response Solution : Taking Laplace transform of the network R Parallel The parallel combination of R, and gives impedance of Applying KVL to the circuit E,(s) = Z Ils) + ls) Rp (l) Eg(s) = Ks) Ry 2) E, ej) + 6) from (2) Substituting in (1) we get Eg(s) R; Fig. 3.38 E,(s) = I) [Z + Ra] [Z+R] E,(s) Ej (5) R, (1+sR, C) Substituting Z, T(s) = ReR desk, O +R: ql _ sR, R,C+R, sta “ RorsR, R,C+R, ~ sep where a " 2 8 a > " Review Questions 1) Define the transfer function of a system. 2) Explain the significance of a transfer function stating its advantages and features. 3) What are the limitations of transfer function approach? 4) How transfer function is related to unit impulse response of a system? 5) Define and explain the following terms related to the transfer function of a system. (i) Poles (ii) Zeros (iii) Characteristic equation (iv) Pole-zero plot (v) Order. The unis impulse response of a system is 7", Find its transfer function fans.: 6aa You have either reached a page that is unavailable for viewing or reached your viewing limit for this book.Principles of Control Systems 3-37 Transfer Function and impulse Response 13) Obtain the transfer function of the network shown in the Fig. 3.40. Ry c c Lyi ett) (t) a(t) 3 Rp Fig. 3.40 tans.; Hi) . __RiRGGs*+ RIG + G)se1 "* E) ~ RIRCC.s+ ®C, + RG + R,C)s+ 1 14) Obtain the transfer function of the network shown in the Fig. 3.47. iy ett) i Fig. 3.41 BG) _ Ka+ ho (Ans.:F') - Gai Where x-—& urs T= RG, and 7, = BE Cy 15. In the circuit of Fig. 3.42, K is the gain of an ideal amplifier. Determine the transfer function 16)/ VG). . R, Ry L vit) K is pln \ i > Fig. 3.42 Tans. 2 KsC, 1 * VG" G+9CR) A+ CR, + LC)Principles of Control Systems 3-38 Transfer Function and Impulse Response 16. 7. 18. 19. 20. Explain the concept of state and state variables. Obtain the state model of RLC series circuit. Define state, state variables, state vector, state space and state trajectory. Explain the state model of linear systems. Explain the dynamic response of second order system with a suitable example. University Question All the exampies asked in previous university papers are solved and included in the examples with solutions. aa00Block Diagram Representation 4.1 Background If a given system is complicated, it is very difficult to analyse it as a whole. With the help of transfer function approach, we can find transfer function of each and every element of the complicated system. And by showing connection between the elements, complete system can be splitted into different blocks and can be analysed conveniently. This is the basic concept of block diagram representation. Basically block diagram is a pictorial representation of the given system. It is very simple way of representing the given complicated practical system. In block diagram, the interconnection of system components to form a system can be conveniently shown by the blocks arranged in proper sequence. It explains the cause and effect relationship existing between input and output of the system, through the blocks. To draw the block diagram of a practical system, each element of practical system is represented by a block. The block is called functional block. It means, block explains mathematical operation on the input by the element to produce the corresponding output. The actual mathematical function is indicated by inserting corresponding transfer function of the element inside the block. Key Point ; For a closed loop systems, the function of comparing the different signals is indicated by the summing point while a point from which signal is taken for the feedback purpose is indicated by take-off point in block diagrams. All these summing points, blocks and take-off points then must be connected exactly as per actual elements connected in the practical system. The connection between the blocks is shown by lines called branches of the block diagram. An arrow is associated with each and every branch which indicates the direction of flow of signal along the branch. Key Point: ‘The signal can travel along the direction of an arrow only. Tt cannot pass against the direction of an arrow. Hence block diagram is an unilateral property of the system. 4-1)ci 8 of Control Systems 4-2 Block Diagram Representation In short any block diagram has following five basic elements associated with it : 1) Blocks 2) Transfer functions of elements shown inside the blocks. 3) Summing points 4) Take-off points 5) Arrows. 41.1 Illustrating Concept of Block Diagram Representation Controter Pneumatic valve Float = Output Fig. 4.1 Liquid level control system For example : Consider the liquid level system as shown in the Fig. 4.1. So to represent this by block diagram, identify the elements which are, i) Controller ii) Pneumatic valve iii) Tank iv) Float. In this system, the level of water is sensed by the float. Hence the float position acts as the feedback. According to the float position, with respect to desired level of water, the controller operates the pneumatic valve controlling the flow of water in the tank. When the required level is reached, controller operates the pneumatic valve in such a way that the flow of water in the tank, stops. If the output from the tank is taken ie. the water from the tank is drained then the float position chages from the desired position and accordingly the controller operates the pneumatic valve to start the flow of water in the tank. Hence indicating all the elements by blocks, the block diagram of the system can be developed as in the Fig. 4.2. th —_) ‘Take-off point Desired level imal Actual T* tevel ‘Summing point Feedback path es Fig. 4.2 Biock diagram of liquid level controlPrinciples of Control Systems 4-3 Block Diagram Representation Consider another example of bottle filling mechanism. When bottle gets filled by the contents upto the required level it should get replaced by an empty bottle. This system can be made closed loop and hence can be shown as in the Fig. 4.3 Valve controling signal Valve Controller Bett driving mech- aniom [Weight Conveyor sensor belt Fig. 4.3 Automatic bottle filling mechanism In the system shown, conveyor belt is driven by the controller as well as valve position is also controlled by the controller. When empty bottle comes at the specific position, weight sensor senses the weight and gives signal to controller. Controller stops conveyor movement and opens the valve so bottle starts getting filled. When required level is achieved, again weight sensor sensing the proper weight sends a signal to controller which sends signals to start movement of belt and also closing the valve position with proper time delay till next empty bottle comes at the proper position. This system can be represented by a block diagram as shown in the Fig. 4.4 Comparator Reference + Filled bottle Control Weight Bett driving mechanism Feedback Fig. 4.4 Block diagramPrinciples of Control Systems 4-4 4.1.2 Advantages of Block Diagram Block Diagram Representation The various advantages of block diagram representation are, 1) Very simple to construct the block diagram for complicated systems. 2) The function of individual element can be visualised from block diagram. 3) Individual as well as overall performance of the system can be studied by using transfer functions shown in the block diagram. 4) Overall closed loop T.F. can be easily calculated by using block diagram reduction rules. 4.1.3 Disadvantages The various disadvantages of block diagram representation are, 1) Block diagram does not include any information about the physical construction of the system. 2) Source of energy is generally not shown in the block diagram. So number of different block diagrams can be drawn depending upon the point of view of analysis. So block diagram for given system is not unique. 4.2 Simple or Canonical Form of Closed Loop System Key Point: A block diagram in which, forward path contains only one block, feedback path contains only one block, one summing point and one take-off point represents simple or canonical form of a closed loop system. This can be achieved by using block diagram reduction rules without disturbing output of the system. This form is very useful as its closed loop transfer function can be easily calculated by using standard result. This result is derived in this section. The simple form can be shown as in the Fig, 4.5. Ris) E(s) ——> cis) Fig. 4.5 Where , R(s) > Laplace of reference input r(t) Cls) + Laplace of controlled output c(t) E(s) > Laplace of error signal e(t) B(s) > Laplace of feedback signal b(t) G(e) + Equivalent forward path transfer function, H(s) ~> Equivalent feedback path transfer function.Principles of Control Systems 4-5 Block Diagram Representation Key Point: G(s) and H(s) can be obtained by reducing complicated block diagram by using block diagram reduction rules. 4.2.1 Derivation of T.F. of Simple Closed Loop System Referring to the Fig. 45, we can write following equations as, Es) = R(s) m Bis) (1) Bis) = C(s)H(s) 2) C(s) = Els)G(s) 3) B(s) = C(s)H(s) and substituting in equation (1) E(s) = R(s) m C(s)H(s) Fo) = Go Cs) R(s) m C(s)H(s) C(s)_ = Ris) G(s) mC(s) G(s)H(s) C(s) [1 + G(s)His) ] = R{s) Gls) Cis) Gls) R@) © TEGE)HG) Use + sign for negative feedback and use ~ sign for pos This can be represented as in the Fig. 4.6 G6) Ris) G(S)H(S) Closed Loop TF. Fig. 4.6 os) Key Point: This can be used as a standard result to eliminate such simple loops in a complicated system reduction procedure. 4.3 Rules for Block Diagram Reduction Any complicated system if brought into its simple form as shown in the Fig. 4.5, its T.F. can be calculated by using the result derived eariler. To bring it into simple form it is necessary to reduce the block diagram but using proper logic such that output of that system and the value of any feedback signal should not get disturbed. This can be achieved by using following mathematical rules while block diagram reduction,Principles of Control Systems 4-6 Block Diagram Representation Rule 1: Associative law : Consider two summing points as shown in the Fig, 4.7. + Ry-R, Ry -Ro+Ry Fig. 4.7 Now change the position of two summing points. Output remains same. So associative law holds good for x summing points which are directly connected to each other (i.e. there is no intermediate block between two summing points or there is no take-off point in Ry between the summing points). Fig. 4.8 R, Ry+Ry Ry #Rg-Rp Consider summing points with a block in between as shown in the Fig. 49. RS (Ry = Rp) Gy + Ry Now interchange two summing points. R, + (Ry+ Rg) Gy-Ry Now the output does not remain same Key Point: So associative law is applicoble to summing points which are directly connected to Fig. 4.10 each other. Rule 2 : For blocks in series : The transfer functions of the blocks which are connected in series get multiplied with each other.Principles of Control Systems 4-7 Block Diagram Representation Consider system as shown in the Fig. 4.11. Ris), —_RUs)B4Gp Fig. 4.11 C{s) = R®)[G, G, GJ So instead of three different blocks, only one block with T.E. [G, G, G5] can be used as shown in the Fig. 4.12. Ris) [ces | cs) Fig. 4.12 Output in both cases is same. Key Point: if there is a take-off or a summing point in between the blocks, the blocks cannot be said to be in series. Consider the combination of the blocks as shown in the Fig. 4.13. Take-off point HEH EF ‘ Fig. 4.13 Key Point: In this combination G,G, are in series and can be combined as GG, but G, is now not in series with G,G, as there is take-off point in between. To call G, to be in series with G,G, it is necessary to shift the take-off point before G,G, or after G3. The rules for such shifting are discussed later. Rule 3 : For blocks in parallel : The transfer functions of the blocks which are connected in parallel get added algebraically (considering the sign). Consider system as shown in the Fig. 4.14.Principles of Control Systems 4-8 Block Diagram Representation Ris) Ris) Gy Fig. 4.14 C(s) = - Ris) G, + Rs), + Rs), = RG)[G.+G,-G,] Now replace three blocks with only one block with LF. G,+G,-G, (Fig. 4.15). Ris) [ere] cs) Cs) = RG) [G,+G, -G,] Output is same. So blocks which are in Fig. 4.15 parallel get added algebraically. Identify the blocks in parallel correctly. The confusing cases are discussed here. Let there exists a take-off point as shown in the Fig. 4.16 along with blocks G,, G, which appear to be in parallel. Take-off point Fig. 4.16 Key Point: But unless and untill this take-off point is shifted before the block, blocks cannot be said to be in parallel. Shifting of take-off point is discussed next. Secondly shifting a Take-off point after a summing point needs some adjustments to keep output same. In above case the take-off point cannot be shown aiter summing point without any alteration. This type of shifting is discussed as critical rules later as such shifting makes the block diagram complicated and should be avoided as far as possible.Principles of Control Systems 4-9 Block Diagram Representation a fl a (a) Avoid such shifting Fig. 4.17 (b) Without any alteration as far as possible such shifting is invalid Not valid Similarly consider a configuration as shown in the Fig. 4.18. This combination is not the parallel combination of G, and H,. Key Point : For a parallel combination the direction of signals through the blocks in parallel must be same. Fig. 4.18 In this case direction of signal through G, and H, is opposite. Such a combination is called minor feedback loop and reduction rule for this is discussed later. Cis) = RG+y Fig. 4.19 Rule 4 : Shifting a summing point behind the block : C®) = RG+y Now we have to shift summing point behind the block. Key Point: The output must remain same, while shifting a summing point. Rex cs) Fig. 4.20 (R+xG = Cle)Principles of Control Systems 4-10 Block Diagram Representation RG +xG = RG+y xG=y x= so signal y must be multiplied with 2 to keep output same, y RE C(s)=RG ry Fig. 4.21 Thus while shifting a summing point behind the block ie. before the block, add a block having T.F. as reciprocal of the T.F. of the block before which summing point is to be shifted, in series with all the signals at that summing point. Rule 5: Shifting a summing point beyond the block : Consider the combination shown in the Fig. 4.22. Rey CH (RtyiG Fig. 4.22 Now to shift summing point after the block keeping output same, consider the shifted summing point without any change. RG+x = RG+yG x = yG ice. signal y must get multiplied with T.F. of the block beyond which summing point is to be shifted.Principles of Control Systems 4-14 Block Diagram Representation Fig. 4.24 Thus while shifting a summing point after a block, add a block having T.F. same as that of block after which summing point is to be shifted, in series with all the signals at that summing point. Rule 6 : Shifting a take-off point behind the block : Consider the combination shown in the Fig. 4.25. Fig. 4.25 c = RG y = RG Key Point: To shift take-off point behind the block value of signal taking-off must remain same. Though shifting of take-off point without any change does not affect output directly, the value of feedback signal which is changed affects the output indirectly which must be kept same. But without any change it is just R as shown in the Fig. 4.26. C=RG y=R Fig. 4.26 But it must be equal to RG. So a block with T.F. G must be introduced in series with signal taking-off after the block. Thus while shifting a take-off point behind the block, add a block having T.F. same as that of the block behind which take-off point is to be shifted, in series with all the signals laking-off from that take-off point.ciples of Control Systems 4-12 Block Diagram Representation C=RG y=RG Fig, 4.27 Rule 7 : Shifting a take-off point beyond the block : Consider the combination shown in the Fig. 4.28. Fig. 4.28 Fig. 4.29 To shift take-off point beyond the block, value of ‘y’ must remain same. To keep value of ‘y’ constant it must be multiplied by ‘1/G’. While shifting a take-off point beyond the block, add a block in series with all the signals which are taking-off from that point, having TF. as reciprocal of the T.F. of the block beyond which take-off point is to be shifted. Rule 8 : Removing minor feedback loop : This includes the removal of internal simple forms of the loops by using standard result derived earlier in section 4.2. Key Point: After eliminating such a minor loop if summing point carries only one signal input and one signal ouiput, it should be removed from the block diagram to avoid further confusion. Cis) RAs) . 4.30Principles of Control Systems 4-13 Block Diagram Representation Rule 9 : For multiple input system use superposition theorem : a Boel System c Fig. 4.34 Consider only one input at a time treating all other as zero. Consider Ry, Ry- Ry= R, =0 and find output C,, Then consider R,, R= R 4, =0 and find output C, At the end when all inputs are covered, take algebraic sum of all the outputs Total output CHG FG Fee Same logic can be extended to find the outputs if system is multiple input multiple output type. Separate ratio of each output with each input is to be calculated, assuming all other inputs and outputs zero. Then such components of outputs can be added to get resultant outputs of the system. In very few cases, it is not possible to reduce the block diagram to its simple form by use of above discussed nine rules. In such case there is a requirement to shift a summing point before or after a take-off point to solve the problem. These rules are discussed below but reader should avoid to use these rules unless and until it is the requirement of the problem. Use of these rules in simple problems may complicate the block diagram. 4.3.1 Critical Rules Rule 10 : Shifting take-off point after a summing point. Consider a situation as shown in Fig. 4.32. Fig. 4.32 Fig. 4.33 Now after shifting the take-off point, let signal taking-off be ‘2’ as shown in the Fig. 4.33. Now z= R tyaa You have either reached a page that is unavailable for viewing or reached your viewing limit for this book.Principles of Control Systems 4-15 Block Diagram Representation Ry Signal 'y' added with same sign Fig. 4.37 Thus it can be noticed that shifting of take-off point before or after a summing point adds an additional summing point in the block diagram and this complicates the block diagram. No doubt, in some rare cases, it is not possible to reduce the block diagram without such shifting of take-off point before or after a summing point. Apart from such cases, do not use such shifting, which will complicate the simple block diagrams. Key Point: Do not use these rules unless and until problem really needs them. 4.3.2 Converting Non-unity Feedback to Unity Feedback Consider a non-unity feedback system, shown in the Fig. 4.38. It is minor feedback loop and hence, LS] ¢ c_G R 7 i4+GH a) a It is to be converted to unity feedback system. But the denominator of closed loop transfer function must remain same as FI9: 4.38 Non-unity feedback system before. ‘ = pas with unity feedback ie. H = 1 1+G’ = 1+GH ie.G’=GH c_ GH Thus, R > 1+GH 8) ek ‘ 1 But transfer function must remain same hence it is necessary to introduce block of i in series with R. Thus converted unity feedback system is as shown in the Fig. 4.39.Principles of Control Systems 4-16 Block Diagram Representation -c Unity feedback Fig. 4.39 Equivalent unity feedback systom C_1) GH G R - HiecH ~iscH «same as before 4.3.3 Procedure to Solve Biock Diagram Reduction Problems Step 1: Reduce the blocks connected in series. Step 2 : Reduce the blocks connected in parallel. Step 3: Reduce the minor internal feedback loops. Step 4; As far as possible try to shift take-off points towards right and summing points to the left. Unless and until it is the requirement of problem do not use rule 10 and 11. Step 5 : Repeat steps 1 to 4 till simple form is obtained. Step 6 : Using standard T-F. of simple closed loop system, obtain the closed loop TF. ce) . Fw Of the overall system. mm Example 4.1: Determine the transfer function C(s)/R(3) of the system shown in the Fig. 4.40, Fig. 4.40Principles of Gontrol Systems 4-17 Block Diagram Representation Solution : The blocks G, and G, are in parallel so combining them as (G, +G.,) we get, Blocks in series Feedback loop G, G4 (Gy +G3) Re)” 1G G,(G.+6,) Hy -G, Gy AyPrinciples of Control Systems 4-18 Block Diagram Representation Cis) | GGG. 4G) Ris) " 1-G, G,H, +6, G,(G,+G,)H, 4.4 Analysis of Multiple Input Multiple Output Systems In these problems, the law of superposition is to be used, considering each input separately. While assuming the other inputs as zero, most of the times if only input is applied to the summing point, summing point is to be removed if not necessary. Yes) Key Point: While removing summing point if sign of the signal present, at that summing point which is to be removed is negative then it must be carried forward in the further analysis. This can be achieved by introducing a block of transfer function -1 in series with that signal. This is the important step to be remembered Fig. 4.44 while solving problems on multiple input multiple output systems. eg. consider a part of system showing two inputs Ris) and Y(s). Other details are not shown for simplicity. When R(s) is considered alone, Y(s) must be assumed zero and summing point at Y(s) can be removed as with Y(s) = 0 there remains only a single signal present at that point so system gets modified as shown in the Fig. 4.42. Fig. 4.42 Now sign of signal from block G, is positive at the summing point which is removed, hence there is no need of adding any other block. Now when Ris) = 0 with ¥(s) active, the summing point at R(s) also can be removed. But now sign of the signal ‘x’ at that summing point is negative which must be considered and carried forward for further analysis. This is possible by adding a block of -1 in series with x without altering any other sign. This avoids the confusion and problem can be solved without any error. Blogk of '-1" Y(s) Fig. 4.43inciples of Control Systems 4-19 Block Diagram Representation ‘mm> Example 4.2: Using block diagram reduction technique find the transfer function from each input to the output C for the system shown in the Fig. 4.44. X(s) Ris) 4.44 Solution : With X(s) = 0, block diagram reduces Minor toop Mino: loop ° ges ° Reg Ris) Cis) 263 G5 (162) (1 * Gs Hs) Ris) ce) = [5 Cis) & 4+ 223 Ss (G2) (1+ G5 Hs) ‘Minor loop Series blocks Fig. 4.44(a)Principles of Control Systems 4-20 Block Diagram Representation COs) | GiGG56; R@ ~ 1¥C, 45H; +G,G;H, #G,G,G, With R(s) = 0, G, vanishes but minus sign at summing point must be considered by introducing block of - 1, as shown. Minor loop Minor loop Note this block Cs) Fig. 4.44(c) Rearranging the input - output we get, os x(s) 1+ GsHs Ss )x( 22) + GSH T+; Minor loop 4.44(d)Principles of Control Systems 4-21 Block Diagram Representation Cis) _ G,G,(1+G,) ‘X(s) ~ 1¥G5H; +G, +G3G5H, #G,G,G; 4.5 Block Diagram from System Equations The block diagram can be constructed from the set of equations representing the system. The addition and subtraction of the various terms is represented by the summing points while multiplication factors are represented by the blocks of the respective uansfer functions. Consider an equation, V> = 4V,-5V; VYje—fa Vy The corresponding block diagram has blocks = of transier functions 4 and 5 along with a summing point to represent the subtraction. It is S}+e¥,; as shown in the Fig. 4.45. Fig, 4.45 The signals V, and V; are taken from their generating points and available V, can be used further for generating other variables and output. Combining the block diagrams of all the system equations, the complete block diagram representations of the system can be obtained. Key Point: Tie block diagrams of electrical systems can be easily obtained by this method. As methods of writing equations for electrical system may vary, the block diagram 1s not unique ‘for the electrical systems. om Example 4.3: Obtain the block diagram for the given electrical netevork. Fig. 4.46 Solution : Convert the given network into Laplace domain and assume the currents as shown in the Fig. 4.46 (a).ples of Control Systems 4-22 Block Diagram Representation Fig. 4.46(a) The KVL equations for the two loops are, -I,R,-1)R, +1:R,+V; = 0 ie -() =1,R3-1,R,-1)R, +1,R, = 0 ie .- (2) And R, Q) Mi 4 hh Ro L v. RitRp ReRyRy 2 ° Equation (1) Equation (2) Equation (3) 4.46(b) Thus the overall block diagram is as shown in the Fig. 4.46(c). Vis) 1 + h Ro hb Vifs) RytR RaR,tRy Ro RyRy Fig. 4.46(c)Principles of Control Systems 4-23 Block Diagram Representation If the equations are written with different method, the different block diagram can be obtained but the transfer function of the system remains same. For the above network we can write equations as, et Ve => 1 1 7 ep e Ve Ro 1 1 “ . K@- Re x = ()-E)R,=1)R,-R, a> I L v= hR => 2 vis) 1 Ry Fig. 4.46(¢)Principles of Control Systems 4-24 Block Diagram Representation Examples with Solutions ump Example 4.4 : Reduce the block diagram and obtain its closed loop T.F. C(s)/R(s). Cis) Solution : No blocks are connected in series or parallel. Blocks having transfer functions G, and H, form minor feedback loop so eliminating that loop we get, Cis) Key Point: Always iry to shift takeoff poini towards right ie. output side and summing point towards left ie, input side, So shift takeoff point after G, to the right. While doing so, it is necessary to add a block having T.F. equal to reciprocal of the T.F. of the block after which takeoff point is to be shifted, in series with signal at that takeoff point. So in series with H, we get a block of 1 H, (er) ie isGohy after shifting take off point. 2 2 Cis)Principles of Contro! Systems 4-25 Block Diagram Representation GiGp FEA G,G, Minor feedback loop H, (1+ Go Hp) & Hy (1+ GH) 2 [as Minor feedback loop G, 6, Ris) TGA GG, cs) - GG Hy (1+ GoHa) (+6,H,+ GG) & Simplifying, ce) GiGs Rg) ~ 1+G,G,+G,H, 1 Hy 1+ Gi, Ga ‘mp ~Example 4.5 : Reduce the block diagram to its simple form and hence obtain C(s)/R(s). es)Principles of Control Systems 4-26 Block Diagram Representation Solution : The blocks G, and H, form minor feedback loop, Ris) cs) Shifting takeoff point as shown , The signal from takeoff point A reaching to summing point B is without any block i.e. gain of that branch joining A to B is one. So introduce block of T.F. 'I' in between A and B to avoid further confusion as shown below, Blocks in paralle! Minor feedback loopPrinciples of Control Systems 4-27 Block Diagram Representation After simplification G, G, (Gp + Gy) C(s) (1+, GH, (T+ 6, H,) ~ Minor feedback loop G1 Gq (G2 +63) Re) +6, GH) (1+ GH) es) G, G,(Gz+ G3) 4+ es 156, 62H) (1+ Gy) cs) _ G, G,(G, +G,) Rs) ~~ 14+G,G,H,+G,H,+G,G S, H, H,+G, G,(G,+G;) imp Example 4.6 : Reduce the block diagram using reduction rules and obtain C(s)/R(s). Solution : Block with T.F. G, and unity gain block are in parallel so combining them we get, Minor feedback loop Ris) cls)Principles of Control Systems 4-28 Block Diagram Representation Shifting takeoff point, Blocks in series R6) G, cI ce) 1+ 63 T¥G, Hy Blocks in parallel Cis) Ris) Minor feedback oop G(1+G3) (1+G,) C(s) ite Hy (Hp + Hz Gat 1) (1+ Gg) Gp + G+ 6)Principles of Control Systems 4-29 Block Diagram Representation > Example 4.29 : Obtain C(s)/R(s) by block diagram reduction. Solution : No blocks are in series or parallel, similarly there is no minor feedback loop existing. Hence shifting takeoff point towards right of the block G, as shown we get, RG) __— Minor loopPrinciples of Control Systems 4-30 Block Diagram Representation a <+— Minor loop, Hp! Gq Ris) After simplification G2G3 Gq 1+G;G,H, 6, G36, qu S2SaSs 1+ G36, Hy Ris) GG, G, Gy 1+ G, G, Hy * G GyH, cs) 616,656, 4+ G46, Ha + G2 63H ce) 616,4,6,4, * TFG, G,Ha* 6: CaF 1Principles of Control Systems 4-31 Block Diagram Representation After simplification, wm Example 4.8: Obtain the TF. by block diagram reduction rul No blocks are in series or parallel so shifting summing point towards left i.e. before the block having transfer function G, as shown in Figure.ciples of Control Systems 4-32 Block Diagram Representation Ris) s. GG, Os) TSG) T+ GFp* GGy After simplification )-(eteen mm Example 4.9 : Reduce the block diagram and obtain its transfer function. (MU : Dec.-2002) Solution : No blocks are in series or parallel and no minor feedback loop is existing so shifting summing point towards left i.e. behind block with transfer function G, as shown, we get, Use Associative law for the summing points, we get,Block Diagram Representation Go (Gy + G,) 1+ GAY Go(Gq + Gs) Hy 1+ GH cs) G, G+G,G5 RG) ~ 1+G,H,+G, GH, +G, HG; Example 4.10 : Obtain C(s)/R(s) using block diagram reduction rules. (MU : May-2003)Principles of Control Systems 4-34 Block Diagram Representation Solution : Separating two feedback paths from second takeoff point which is after the block having transfer function G, as shown, we get, Shifting summing point behind the block having transfer function ‘G,’ as shown wePrinciples of Control Systems 4-35 Block Diagram Representation Use Associative Law for the two summing points and interchange their positions, we Minor loopPrinciples of Control Systems 4-36 Block Diagram Representation 6,66, R(s) 7+ GH, -G.GH, pee T+GH,-G.GH, 6, 1 R G4 and other block are in parallel RG) ump Example 4.11: Find C(s)/R(s) using block diagram reduction. <—Minor loopPrinciples of Control Systems 4-37 Block Diagram Representation G3 Ris) | Sy Sf 1-6, + Parallel SG 14+ Sy Parallel Cs) _ G,-G,G,H,+G,+G, RS — I- nm Example 4.12: Obtain C(s)/R(s) using block diagram reduction technique. (MU : May-1994, Nov.-2005, 10 Marks)Principles of Control Systems 4-38 Block Diagram Representation Solution : Cis) Ris) sr Feedback toon Ris) Got G,GoH,+ iG, T+ 6H, Rie) Ga(G5 + GGsHy + GiG2Gs) R(s) 1+ GH, Cs) (Gs + GyGsH, + G,G,Principies of Control Systems 4-39 Block Diagram Representation ‘mp Example 4.13 : Lise of Rule No. 10, critical rule illustration. Reduce the block diagram Cs) id obtain ——. and obtain Rc Solution : Shifting takcoff point before G).Principles of Control Systems 4-40 Block Diagram Representation Separating the paths in the feedback path shown dotted, Minor feedback loop —HyH2G2 Key Point: Remember that though the paths through summing point are separated, signs at the summing points to those paths must be carried as it is. Hence after H,, carry the negative sign and then H, G, to get - H, H, Gp. Shifting summing point as shown and then interchanging the two summing points using Associative Law we get, Blocks in parallel cs)Principles of Control Systems 4-44 Block Diagram Representation see Gah) Ce) _ _@+G 7H) U+H, G; Ga) RS) ~ > GiG,+C,)(-H, H, G) (1+ G, H,)(1+H, G, G3) cs) GG, +S) RG) ~ 1+G, 1, +H, G,G,-G, GG, Hy, A mp Example 4.14: Find the transfer function for the block diagram given below using block diagram reduction technique. Solution : ‘Separate the two paths as shown dotted. Shif takeoff point a after 2 GyPrinciples of Control Systems 4-42 Block Diagram Representation 112. —— Series 26, c SL shitttakeott i | point after 2 G,G, 2G,G,.G5 T-HG, +2G,G,H 1261626; T-HG, +2G,G,H “2G,G, ZA 1 2G,G,G, T=HG,#26,G +6, vo Ans.Principles of Control Systems 4-43 Block Diagram Representation ‘mp Example 4.15: Obiain the expression for C, and C, for the given multiple input multiple output system. Solution : In this case there are two inputs and two outputs. Consider one input at a time assuming other zero and one output at a time. Consider R, acting, R, = 0 and C, not considered R, = 0 and C, is suppressed (not considered). C, suppressed does not mean that C, = 0. Only it is not the focus of interest while C, is considered. As R,=0, summing, point at R, can be removed but block of ‘1 must be introduced in series with the signal which is shown negative at that summing point. Forward path E> Pal R, +] C, ior s al | Feedback path Feedback path ‘Minor loopPrinciples of Control Systems 4-44 Block Diagram Representation G ~G, G;G, “ THEG, G; GIG] ~ For ee R, = and C, is suppressed. Ere. Forword, ” oa R i G Minor loop CG = 6) G3 Gy - 261 G2 Gs R, T+FG, G; GIG3] ~1-G, G,G, G, = 0 and C, is suppressed. [=] Ls] | Feedback ~ = Minor loop Be G (> Forward path Co G) R, 1+IG,1FG; G3 Gy] Gp T= GG, GiGi, o> Example 4.16 : techniques Cl Obtain psi for the block diagram shown below using reductionPrinciples of Control Systems 4-45 Block Diagram Representation c Solution : Rearranging the block diagram we get, ea} fa}fa} fa} . 4 ' senate \ Separate the feedback paths through Gy and G;, combined at summing point before G,. So G,, will appear separately in each path of G, and G,, as shown below. Minor loop Reducing inner minor feedback loop,Principles of Control Systems 4-48 Block Diagram Representation Hint : Combine inner blocks, reduce minor feedback loop. Again combine blocks in forward path to get simple form. Using 7 son we get, Cs) RG) “14, C, G, +G, G, G, C, G,+G, GC, GG, ww Ans ‘=> Example 4.17 : The system block diagram is given below CH ewan pice aoe Find i) Ee) if N(s)= 0 ii) Rs) if N(s) = 0 iii) N 10 56+) 10 10 Minor feedback loop = ="S5e S4st5s s+ Weep”:Principles of Control Systems 4-47 Block Diagram Representation Assume output of second summing points as X(s), Hence E(s) = Ris) - Cis) (i) Cis) = (ii) XG) = E+ 2, RG) ai) s) = Ee)+ 3 RG i Substituting value of X(s) and R(s) from (i) & (ii) in (iii) we get, 87+ 63 faery CO = F) + 3B + 3 cs) s?+ 6s [ses waco = (+33) HO (s? + 6s - 30) (+7). Tossa) O°) > Gew FO Cis) _ _10(6+7) FO) ~ Feenag WNP NO= ii) To find © a 3 we have to reduce block diagram solving minor feedback loop and shifting summing point to the left as shown earlier in (i). So referring to block diagram after these two steps ic.Principles of Control Systems 4-48 Exchanging two summing points using associative law, 3 Parallel of ‘1’ and —— arallel of 1" and 3 =1+— sea Minor loop 1+GH :. Block diagram becomes, Block Diagram Representation 10 (s+4) 2 +68 10(s +4) +e) +65 RQ Ts cis) eee Ss + 16s+40 Cs) _ (23) 10(s+4)_)_ Ris) s+ 4) © (6? 4 1654 40 10(s+7) s? 416+ 40 iii) With R(s) = 0 block diagram becomes, The block of ‘3’ will not exist as R(s) 0. Similarly first summing point will also vanish but student should note that negative sign of feedback must be considered as it is, though summing point gets deleted. In general while deleting summing point, it is necessary to consider the signs of the different signals at that summing points and should not be disturbed. So introducing block of ‘1’ to consider negative sign.Principles of Control Systems 4-49 Block Diagram Representation =— Parallel Two blocks are in parallel, adding them with signs. ‘fier simpification (— 1.5 — 4) Removing summing point, as sign is positive no need of adding a block. IN(s) cls) Minor loop with G = 1 Cs) 1 NO" | , 155 +40 ~ s(s+1) Cs) _ s@+1) N@ © 3? +16s+ 40 imap Example 4.18 : Draw a block diagram for the electric circuit shown and hence evaluate the transfer function E, (s) / E,(s).Principles of Control Systems 4-50 Block Diagram Representation 100 k2 1 pF ; | ei = 10 uF e Ma entt) Lop Solution : Let R, = 100 kQ, C,=10 pF, C)=1 pF, R,= 1 MQ Draw the s-domain network and shown the loop currents and node voltages. 1 Ry V,(s) SC2 E\()- V6) From R, branch, [,(s) = =! H 1 1 From ee branch, Vits)= 1h (8)-136)] % 3 V,(s)-E, (8) [zs] sC.{V (5) - E,(6)] From R, branch, E,(s) = 1,(s) Ry i) —+[R, }— E18) Combining all the block diagrams, the block diagram of overall electrical system is as shown, branch, 1,(s) = E,(s)Principles of Control Systems 4-51 Block Diagram Representation Shift summing point before a and takeoff point after R,. Then interchange the 7 summing point near E(s). Minor feedback loops ' EO) 4 2) E,(s) E,(s) sC,R, E(s)___ @+sGR)G+sGR) _ sC.Ry B® | sGR, R, — 1+sC,R, +sC,R, +8°R,C,R,C; +sC,R; *AFsGR1+8G,R,) “Ry Using the values of R,, Ry, C, and C,. E,(s) E\@) ~ s*+2.1s+1of Control Systems 4-52 Block Diagram Representation tmp Example 4.19 : Obtain the resultant output C(s) in terms of the inputs R(s) and Y(s) Ys) Solution : As there are two inputs, consider each input separately. Consider R(s), assuming Y(s) = 0. Cs) Cis) _ GG, G, Re ~ 1+6,G,H, So part of C(s), due to R(s) alone is, ‘ GG; Cis) = Ris) lreetr| Now consider Y(s) acting with R(s) = 0. Now sign of signal obtained from H, is negative which must be carried forward, though summing point at R(s) is removed, as R(s) = 0, so we get, Ys} Y(s) Cs) Series| Now equivalent G = G,, tracing forward path from input summing point to output. Equivalent H = -G, H, tracing feedback path from output to input summing point. While sign of the final feedback is positive at the input summing point Cc) _ GC G G, Yo) BG ~GH~i-G,(-G,H,) ~ 1+6,G,H,aa You have either reached a page that is unavailable for viewing or reached your viewing limit for this book.Principles of Control Systems Block Diagram Representation \ \ After simplification After simpiification os) s+10 s(2s*7) sett “(+ 10)6+3) s(2s+7) Cs) +I) 6-3) _. s(2s+7)(s-4) Ro) s(25+7) +8) (s+11)(s— 3)(s—4) + s(28+7)(s° +8) *Se- ce) Ris) 32Principles of Control Systems 4-55 Block Diagram Representation Simplification Interchanging the summing points using associative law, [Minor loop Series — > G,G, GG, +6, ] TECH, GPrinciples of Control Systems 4-58 Block Diagram Representation Afer simpificat G4(GyGq + Gy) G,(G,G, + G,) 1+ GiG7Hy + Hy (G2Gq * Gs) 1+ GGA, |, SilG26a* Ga) He 1+*G,GH, “6, G,(G,G,+6,) c_ TOGA +HG GG) R GiGi Ga + Gy 1+ [eG A +H G,G,+G,) . GG;G,+G,) ~ +6, C,H, +C,G,H,+G, H,+G, G,G CG, Gy imp Example 4.22 : In the given block diagram, obtain the transfer function of the system C,/Ry (MU : Nov.-96)Principles of Control Systems 4-57 Block Diagram Representation As C, is not the focus of interest and hence G, becomes meaningless in the block diagram. Shifting take off point to the right of G). G, G, G, G,G, Hy, GQ. OFC, 6) FG) RG 3G, Gs Ay +G,G,) (+G,) G,G5 q im G, G, G3 Gy G5 Hy R, 1+G,G,+G,+G,G,G,—G, G,G;H, HyPrinciples of Control Systems 4-58 Block Diagram Representation imp Example 4.23 : Determine the transfer functions C/R, and C/R, from the block diagram shozon in figure using block diagram reduction techniques. (MU: Dec.-2006, May-1999) Go -[s, Ry ov Solution : For finding C/R,, assume R, = 0 hence the block diagram reduces to, f | | {Minor loop R, 4 G, +) 1S cs) t Parallel Ee ie 6 a a -< [co _(G+G *63H “TR, 7 1 3 Hy To find C/R,, assume R, = 0 hence G,, G, will vanish but negative sign of H, will continue. So we get, c Gs +c Hy mm) Example 4.24 : Find C using - block diagram reduction techniques. (MU : May-98)