Scribd
Upload
106 views

Ee4090 Electrical Engineering Drawing

This document outlines the modules and topics covered in the EE4090 Electrical Engineering Drawing course. The course has 4 modules that cover armature windings, transformers, rotating machines including DC machines, alternators, and induction motors, and substations. Key topics include sketches of armature windings, transformer components, sections of motors and generators, and layouts of substations. The course has a total of 56 contact hours and prerequisites of EE2007 and EE3003 Electrical Machines courses.

Uploaded by

subineee
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
106 views

Ee4090 Electrical Engineering Drawing

This document outlines the modules and topics covered in the EE4090 Electrical Engineering Drawing course. The course has 4 modules that cover armature windings, transformers, rotating machines including DC machines, alternators, and induction motors, and substations. Key topics include sketches of armature windings, transformer components, sections of motors and generators, and layouts of substations. The course has a total of 56 contact hours and prerequisites of EE2007 and EE3003 Electrical Machines courses.

Uploaded by

subineee
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

EE4090 ELECTRICAL ENGINEERING DRAWING

Pre-requisites: EE2007 Electrical Machines I & EE3003 Electrical Machines II


L

Total Hours: 56 Hours


Module 1: Armature Windings
(16 Hrs)
1. Simplex lap/ wave dc armature windings with equalizer rings/ dummy coils.
2. Simplex lap/ wave, integral/ fractional slot, double layer three phase ac armature windings with full pitched/
short chorded coils.
3. Mush type/ concentric, 2-tier/ 3-tier, bifurcated/ unbifurcated single layer three phase ac armature windings.
Module 2: Transformers
1.
Sectional plan and elevation of a transformer limb with windings.
2.
Sectional plan and elevation of the core assembly of a power transformer.
3.
Sectional plan and elevation of a distribution transformer tank with its accessories.
4.
Sketches of capacitor and oil filled type transformer bushings.

(12 Hrs)

Module 3: Rotating Machines


DC Machines
1.
Sectional front and side elevation of armature with commutator.
2.
Sectional front and side elevation of yoke and pole assembly with field winding.
3.
Sectional front and side elevation of assembled Machine.
Alternators
1.
Sketches of the methods of pole fixing and slot details of turbo & water wheel alternators.
2.
Sectional front and side elevation of water wheel rotor assembly with winding.
3.
Sectional front and side elevation of salient pole alternator.
4.
Sectional front and side elevation of turbo alternator.
Induction Motors
1. Sectional front and side elevation of slip ring induction motor.
2. Sectional front and side elevation of squirrel cage induction motor.

(24 Hrs)

Module 4: Substations
1.
Layouts and single line diagrams of outdoor and indoor substations.
2.
Layout of a 220KV substation.
3.
Layout of a captive power substation.
4.
Single line diagram of a distribution center.

Text/Reference Books:
1.
2.
3.
4.
5.

Clayton & Hancock, Performance and Design of DC Machines, ELBS, 1992.


Say M.G, Performance and Design of AC machines, Pitman, ELBS, 1991.
A.K. Sawhney, Electrical Machine Design, Dhanpath Rai, New Delhi, 1991.
Narang K.L., A Text Book of Electrical Engineering Drawing, Tech India Publications.
Bhattacharya S.K, Electrical Engineering Drawing, Wiley Eastern, Edition 2.

63

(4 Hrs)

You might also like