Scribd
Upload
25 views

Experiment No: 7 Name of The Experiment: Steady State AC Analysis and Frequency Response

1. The document describes the results of four steady state AC circuit analyses: 2. A high pass filter with a half power frequency of 1 kHz. 3. A low pass filter with a half power frequency of 12.686 kHz. 4. A band pass filter with a bandwidth of 2982 Hz between 304.322 Hz and 3.2860 kHz. 5. A band stop filter showing attenuation of a signal against an inductor in an RLC circuit.

Uploaded by

Tanvir Sadiq Toki
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
25 views

Experiment No: 7 Name of The Experiment: Steady State AC Analysis and Frequency Response

1. The document describes the results of four steady state AC circuit analyses: 2. A high pass filter with a half power frequency of 1 kHz. 3. A low pass filter with a half power frequency of 12.686 kHz. 4. A band pass filter with a bandwidth of 2982 Hz between 304.322 Hz and 3.2860 kHz. 5. A band stop filter showing attenuation of a signal against an inductor in an RLC circuit.

Uploaded by

Tanvir Sadiq Toki
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 8

Experiment No: 7

Name of the Experiment: Steady state AC analysis and frequency response


1. High Pass Filter:
Circuit Diagram:

Input File:
High pass frequency
V2 1 0 Ac 1v
C1 1 2 100u
R1 2 0 1.59
.Ac dec 20 100 100000
.probe
.end
Output File:
**** 10/04/15 23:22:52 ******* Evaluation PSpice (Nov 1999) High pass frequency ****
CIRCUIT DESCRIPTION
V2 1 0 Ac 1v
C1 1 2 100u
R1 2 0 1.59
.Ac dec 20 100 100000
.probe
.end
**** 10/04/15 23:22:52 *********** Evaluation PSpice (Nov 1999) **************

High pass frequency


NODE VOLTAGE
(

1)

0.0000 (

2)

NODE VOLTAGE

NODE VOLTAGE

NODE VOLTAGE

0.0000

VOLTAGE SOURCE CURRENTS


NAME
V2

CURRENT
0.000E+00

TOTAL POWER DISSIPATION 0.00E+00 WATTS


JOB CONCLUDED
TOTAL JOB TIME

.05

The half power frequency:


At -3db point:
0

(1.0000K,-3.0145)

-10

-20

-30
100Hz
300Hz
DB(V2(R1)/V1(V2))

1.0KHz

3.0KHz
Frequency

The half power frequency:

10KHz

30KHz

100KHz

1.0

(1.0000K,706.762m)

0.5

0
100Hz
300Hz
V2(R1) / V1(V2)

1.0KHz

3.0KHz
Frequency

2. Low pass filter:


Circuit diagram:

Input file:
Low pass filter

10KHz

30KHz

100KHz

V1 1 0 ac 1
R1 1 2 .25
C1 2 0 50u
.ac dec 20 100 100000
.probe
.end
Output File:
10/04/15 23:27:55 *********** Evaluation PSpice (Nov 1999) **************
Low pass filter
CIRCUIT DESCRIPTION
V1 1 0 ac 1
R1 1 2 .25
C1 2 0 50u
.ac dec 20 100 100000
.probe
.end
**** 10/04/15 23:27:55 *********** Evaluation PSpice (Nov 1999) ************** Low
pass filter
****

SMALL SIGNAL BIAS SOLUTION

NODE VOLTAGE NODE VOLTAGE


0.0000 ( 2) 0.0000

TEMPERATURE = 27.000 DEG C


NODE VOLTAGE

VOLTAGE SOURCE CURRENTS


NAME
V1

CURRENT

0.000E+00

TOTAL POWER DISSIPATION 0.00E+00 WATTS


JOB CONCLUDED TOTAL JOB TIME

Half power frequency:

0.00

NODE VOLTAGE(

1)

1.0

(12.686K,708.322m)

0.5

0
100Hz
300Hz
V1(C1) / V1(V1)

1.0KHz

3.0KHz

10KHz

30KHz

100KHz

Frequency

Half power frequency at -3db point:


0
(12.686K,-2.9964)

-5

-10

-15

-20
100Hz
300Hz
DB(V1(C1)/V1(V1))

1.0KHz

3.0KHz
Frequency

3. Band pass filter :

10KHz

30KHz

100KHz

Highest value:
400mV
(1.0000K,333.333m)

300mV

200mV

100mV

0V
100Hz
V(R2:2)

300Hz

1.0KHz

3.0KHz
Frequency

Normalization to determine band width:

10KHz

30KHz

100KHz

1.2

0.8

(304.322,708.728m)

(3.2860K,709.553m)

0.4

0
100Hz
300Hz
V(R2:2) / V1(V1) /333.33m

1.0KHz

3.0KHz
Frequency

So, band width


=2982 hz

= (3286-304)hz

4. Band stop:
Circuit diagram:

Band stop against L in RLC circuit:

10KHz

30KHz

100KHz

3.0

2.0

1.0

0
10Hz
100Hz
V(L2:1) / V1(V1)

1.0KHz

10KHz
Frequency

100KHz

1.0MHz

10MHz

You might also like