CSWA Sample Exam Questions Certified SolidWorks Associate (CSWA) Sample Exam Questions ‘The questions below represent sample CSWA Exem questions. Part modeling anc assembly modeling questions that require you to build model should be correctly answered in 45 minutes or less. Question 2 and Question 3 should be correctly answered in 5 minutes or less. Question, Build this part in SolidWorks. Unit system: MMGS (1 llimeter, gram, second) Decimal places: 2. Part origin: Arbitrary ‘A= 63mm, 8=Somm, Part material: Copper Density ~ 0.0089 g/mm’3 What is the ‘overall mass of ‘the part in grams? a) 1205, = 100mm. All holes through all, b) 1280 14a d) 1108CSWA Sample am Questions Question 2 COSMOSXPress allows changes to mesh settings. Which of the following, statements is not True? 1a) A fine mesh setting produces more accurate results then a course mesh. b) A coarse mesh setting produces less accurate results than a fine mesh. )A fine mesh setting can be applied toa specific face instead of the entire model. 4) All of the above Question 3, To create drawing view, ‘B’ itis necessary OFA to sketch a spline (as shown] on drawing view ‘A’ and insert which SolidWorks view type? a) Brokenout Section ) Aligned Section ©) Section 4) Detail pace 2CSWA sample am Questions Question 4, Build this assembly in SolidWorks. Itcontains 3 machined brackets and 2 pins. Brackets: 2mm ‘thickness, and equal size (holes through-all). Material: 6061 Alloy, Density = 0.0027¢/mm)3, The top edge of the notch is located 20 mm from the top ‘edge of the MachinedBracket. Pins: 5 mm length and equal in diameter, Material: Titanium, Density 0.00462/mm*3. Pins are mated concentric to bracket holes (no clearance), Pin end faces are coincident to bracket outer faces. There isa 1mm gap between the brackets, Brackets are positioned with equal angle mates (45 degrees). Unit system: MMGS (millimeter, gram, second) Decimal places: 2 Assembly origin: As shown, ‘What is the center of mass of the assembly? a) X=1105 ¥=24.08 — 7=-40.19 b) X=1105 Y=-2408 7-40.19 c) X=4024 ¥=74337=20.75 a) X=2075 Y=24.33 2=40.24 Pace 3CCSWASample Exam Questions Question Build this assembly in SolidWorks. It contains 3 ‘components: Base, Yoke, Adjusting Pin. Apply the MMGS unit system. Material: 1060 Alloy for all ‘components. Density = 0.0027¢/mm*3, Base: The distance between the front face of the Base and the front face of the Yoke = 60mm. Yoke: The Yoke fits inside the left and right square channels ofthe Base component, {no clearance). The top face of the Yoke contains a 12mm. through-all hole. AdjustingPin: The bottom face of the AdjustingPin head is located 40 mm from the top face of the Yoke component. The AdjustingPin ‘component contains a 5mm though all hole. What is the center of mass of the assembly with respect to the illustrated coordinate system? a) X=30.00 Y=40.16 Z=-49.16 b) X=30.00 Y=40.16- 2=-43.82 c) X=-30.00 Y=40.16 2-50.20 d) X30.00 Y=40.16 2-53.82 Pace 4(CSWA Same Bxam Questions paceSWA Sampe bam Questions Question, Build this par SolidWorks. Materal: 6061 Alloy. Densi 0.0027g/mm'3 Unit system: Decimal places: 2. Part origin: Arbitrary A=100. All holes through all, unless otherwise specified What is the overall mass of the part in grams? a) 2040.57 b) 2004.57 c} 102.63 a) 1561.23SWA Sample Exam Questions For further preparation, please complete the SolidWorks tutorials, located in ‘SolidWorks under the Help Menu, before taking the CSWA Exam. Review the “About the CSWA Exam" document located at www solidworks. com/esiva, Good Luck, Certification Program Manager, SolidWorks Corporation Correct answers: oy eoNnE voaomoc