Scribd
Upload
272 views

PIC Programmer

This document provides instructions for building a PIC programmer circuit using a PIC16F84 microcontroller. It includes a schematic and printable PCB layout files. The programmer connects to a computer via RS-232 and can be powered by a 15V DC or AC adapter. The GREEN LED indicates sufficient power and the RED LED shows programming is in progress. While it works for most PICs, programming PIC12Cxxx is not supported.

Uploaded by

dardaryu
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
272 views

PIC Programmer

This document provides instructions for building a PIC programmer circuit using a PIC16F84 microcontroller. It includes a schematic and printable PCB layout files. The programmer connects to a computer via RS-232 and can be powered by a 15V DC or AC adapter. The GREEN LED indicates sufficient power and the RED LED shows programming is in progress. While it works for most PICs, programming PIC12Cxxx is not supported.

Uploaded by

dardaryu
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

PIC Programmer: the hardware.

Introduction
I found this PIC programmer on www.lancos.com;
I created a specialised circuit for PIC 16 series,
added some new features and created a compact
PCB layout
I have very good experiences with this
programmer for PIC16F84
(believe me it is not the first one I tried :-) ).

!NOTE programming PIC12Cxxx DOES


NOT WORK. Although the Ponyprog
software suggests that this is OK, I have serious
trouble with these types. On the Ponyprog Forum I found more complaints about these types.

Main advantage of this programmer is that it uses the serial RS232 COM port which is (unlike
the parallel port) freely accessible in NT 2000 and XP.
The software is available on my homepage or at the lancos site.

First build the programmer as in the schematic below.You can build it on an experimental board
or use the PCB layout; copper tracks and component setup are available in 1:1 scale (if printed
on A4 scale) below:

COPPER LAYOUT (pdf 31 kByte; right click to download)


COMPONENT SETUP (pdf 20 kByte; right click to download)

Some hardware features / comments:

-The GREEN LED indicates that the programming voltage is high enough, (Must be at least 13V
DC
-The RED LED indicates that programming oor reading is in progress
-The 847/857 transistors are general purppose SMD transistors that I used, BC547 & 557 are also
OK.
-The diode bridge prevents wrong polarityy of the power supply, this way it can be + /- or even
AC !
-The 78L05 has a 100mA current limit. Thiis will give you some protection (not guaranteed!) to
your PIC
and you computer. Do NOT use a regular 1Ampere 7805, if you make a mistake you will blow
up
your serial port for sure!
Download printable PDF schematic: PICPROG-SCHEMATIC (right click to download)

Power supply
Connect a 15V DC or AC adapter to the DC input of the PIC programmer

• Polarity is not important because the PIC programmer has an internal rectifier.
• The GREEN LED of the PIC Programmer indicates that the power supply is
OK.
Note: many 12 V adapters will also work because they provide more than 15V at low currents.
If the green LED burns, the supply is ok.

RS232 connection
Connect the PIC programmer to a COM port of a (Windows) PC with a 9-pin serial
cable.

• A serial cable has a 9-pin FEMALE and a MALE sub D connector


• Do not use a null modem cable

Connection drawing:

Your programmer is ready for use, please proceed to the software setup on my main home
page:

BACK TO MAIN PAGE

Hosting by WebRing.

You might also like