1999 Jeep TJ Wrangler Service Manual - 08. Electrical Systems

TJ STARTING SYSTEMS 8B - 1
STARTING SYSTEMS
CONTENTS
page page
DESCRIPTION AND OPERATION STARTER RELAY . . . . . . . . . . . . . . . . . . . . . . . . 9

STARTER MOTOR . . . . . . . . . . . . . . . . . . . . . . . . 2 STARTING SYSTEM . . . . . . . . . . . . . . . . . . . . . . 3
STARTER RELAY . . . . . . . . . . . . . . . . . . . . . . . . 3 REMOVAL AND INSTALLATION
STARTING SYSTEM . . . . . . . . . . . . . . . . . . . . . . 1 STARTER MOTOR . . . . . . . . . . . . . . . . . . . . . . . 10
DIAGNOSIS AND TESTING STARTER RELAY . . . . . . . . . . . . . . . . . . . . . . . 12
STARTER MOTOR . . . . . . . . . . . . . . . . . . . . . . . . 8 SPECIFICATIONS
STARTER MOTOR NOISE - 2.5L ENGINE . . . . . 7 STARTING SYSTEM . . . . . . . . . . . . . . . . . . . . . 13
DESCRIPTION AND OPERATION System for complete service information for the igni-
tion switch.
STARTING SYSTEM • Refer to Clutch Pedal Position Switch in the
proper section of Group 6 - Clutch for complete ser-
DESCRIPTION vice information for the clutch pedal position switch.
An electrically operated engine starting system is • Refer to Park/Neutral Position Switch in the
standard factory-installed equipment on this model. proper section of Group 21 - Transmission for com-
The starting system is designed to provide the vehi- plete service information for the park/neutral posi-
cle operator with a convenient, efficient and reliable tion switch.
means of cranking and starting the internal combus- • Refer to the proper section of Group 8W - Wir-
tion engine used to power the vehicle and all of its ing Diagrams for complete service information and
accessory systems from within the safe and secure circuit diagrams for the starting system wiring com-
confines of the passenger compartment. See the own- ponents.
er’s manual in the vehicle glove box for more infor- Group 8A covers the Battery, Group 8B covers the
mation and instructions on the recommended use Starting Systems, and Group 8C covers the Charging
and operation of the factory-installed starting sys- System. We have separated these systems to make it
tem. easier to locate the information you are seeking
The starting system consists of the following com- within this Service Manual. However, when attempt-
ponents: ing to diagnose any of these systems, it is important
• Battery that you keep their interdependency in mind.
• Starter relay The battery, starting, and charging systems in the
• Starter motor (including an integral starter sole- vehicle operate with one another, and must be tested
noid) as a complete system. In order for the vehicle to start
• Ignition switch and charge properly, all of the components that are
• Clutch pedal position switch (manual transmis- used in these systems must perform within specifica-
sion) tions.
• Park/neutral position switch (automatic trans- The diagnostic procedures used in each of these
mission) groups include the most basic conventional diagnostic
• Wire harnesses and connections (including the methods, to the more sophisticated On-Board Diag-
battery cables). nostics (OBD) built into the Powertrain Control Mod-
This group provides complete service information ule (PCM). Use of an induction-type milliampere
for the starter motor and the starter relay. Complete ammeter, volt/ohmmeter, battery charger, carbon pile
service information for the other starting system rheostat (load tester), and 12-volt test lamp may be
components can be located as follows: required.
• Refer to Battery in the proper section of Group All OBD-sensed systems are monitored by the
8A - Battery for complete service information for the PCM. Each monitored circuit is assigned a Diagnos-
battery. tic Trouble Code (DTC). The PCM will store a DTC in
• Refer to Ignition Switch and Key Lock Cyl- electronic memory for any failure it detects. Refer to
inder in the proper section of Group 8D - Ignition On-Board Diagnostic Test For Charging System
8B - 2 STARTING SYSTEMS TJ
DESCRIPTION AND OPERATION (Continued)
in the Diagnosis and Testing section of Group 8C - noid plunger hold-in coil. Current now flows between
Charging System for more information. the solenoid battery terminal and the starter motor,
energizing the starter.
OPERATION Once the engine starts, the overrunning clutch pro-
The starting system components form two separate tects the starter motor from damage by allowing the
circuits. A high-amperage feed circuit that feeds the starter pinion gear to spin faster than the pinion
starter motor between 150 and 350 amperes, and a shaft. When the driver releases the ignition switch to
low-amperage control circuit that operates on less the On position, the starter relay coil is de-energized.
than 20 amperes. The high-amperage feed circuit This causes the relay contacts to open. When the
components include the battery, the battery cables, relay contacts open, the starter solenoid plunger
the contact disc portion of the starter solenoid, and hold-in coil is de-energized.
the starter motor. The low-amperage control circuit When the solenoid plunger hold-in coil is de-ener-
components include the ignition switch, the clutch gized, the solenoid plunger return spring returns the
pedal position switch (manual transmission), the plunger to its relaxed position. This causes the con-
park/neutral position switch (automatic transmis- tact disc to open the starter feed circuit, and the shift
sion), the starter relay, the electromagnetic windings lever to disengage the overrunning clutch and pinion
of the starter solenoid, and the connecting wire har- gear from the starter ring gear.
ness components. Following are general descriptions of the major
If the vehicle is equipped with a manual transmis- components in the starting system.
sion, it has a clutch pedal position switch installed in
series between the ignition switch and the coil bat- STARTER MOTOR
tery terminal of the starter relay. This normally open
switch prevents the starter relay from being ener- DESCRIPTION
gized when the ignition switch is turned to the The starter motors used for both the 2.5L and the
momentary Start position, unless the clutch pedal is 4.0L engines available in this model are not inter-
depressed. This feature prevents starter motor oper- changeable. Both starter motors are mounted with
ation while the clutch disc and the flywheel are two screws, but the 2.5L starter motor is mounted to
engaged. The starter relay coil ground terminal is the right rear corner of the engine block, while the
always grounded on vehicles with a manual trans- 4.0L starter motor is mounted to the manual trans-
mission. mission clutch housing or automatic transmission
If the vehicle is equipped with an automatic trans- torque converter housing on the right side of the
mission, battery voltage is supplied through the low- engine.
amperage control circuit to the coil battery terminal Each of these starter motors incorporates several
of the starter relay when the ignition switch is of the same features to create a reliable, efficient,
turned to the momentary Start position. The park/ compact, lightweight and powerful unit. The electric
neutral position switch is installed in series between motors of both starters have four brushes contacting
the starter relay coil ground terminal and ground. the motor commutator. The 2.5L starter motor uses
This normally open switch prevents the starter relay four permanent magnets for the field poles, while the
from being energized and the starter motor from 4.0L starter motor features four electromagnetic field
operating unless the automatic transmission gear coils wound around four pole shoes. The 2.5L starter
selector is in the Neutral or Park positions. motor is rated at 1.2 kilowatts (about 1.6 horse-
When the starter relay coil is energized, the nor- power) output at 12 volts, while the 4.0L starter
mally open relay contacts close. The relay contacts motor is rated at 1.4 kilowatts (about 1.9 horse-
connect the relay common feed terminal to the relay power) output at 12 volts.
normally open terminal. The closed relay contacts Both of these starter motors are serviced only as a
energize the starter solenoid coil windings. unit with their starter solenoids, and cannot be
The energized solenoid pull-in coil pulls in the sole- repaired. If either component is faulty or damaged,
noid plunger. The solenoid plunger pulls the shift the entire starter motor and starter solenoid unit
lever in the starter motor. This engages the starter must be replaced.
overrunning clutch and pinion gear with the starter
ring gear on the manual transmission flywheel or on OPERATION
the automatic transmission torque converter drive These starter motors are equipped with a plane-
plate. tary gear reduction (intermediate transmission) sys-
As the solenoid plunger reaches the end of its tem. The planetary gear reduction system consists of
travel, the solenoid contact disc completes the high- a gear that is integral to the output end of the elec-
amperage starter feed circuit and energizes the sole- tric motor armature shaft that is in continual
engagement with a larger gear that is splined to the relay contact is held against one of the fixed contacts
input end of the starter pinion gear shaft. This fea- (normally closed) by spring pressure. When the elec-
ture makes it possible to reduce the dimensions of tromagnetic coil is energized, it draws the movable
the starter. At the same time, it allows higher arma- contact away from the normally closed fixed contact,
ture rotational speed and delivers increased torque and holds it against the other (normally open) fixed
through the starter pinion gear to the starter ring contact.
gear. When the electromagnetic coil is de-energized,
The starter motors for both engines are activated spring pressure returns the movable contact to the
by an integral heavy duty starter solenoid switch normally closed position. The resistor or diode is con-
mounted to the overrunning clutch housing. This nected in parallel with the electromagnetic coil in the
electromechanical switch connects and disconnects relay, and helps to dissipate voltage spikes that are
the feed of battery voltage to the starter motor and produced when the coil is de-energized.
actuates a shift fork that engages and disengages the
starter pinion gear with the starter ring gear.
Both starter motors use an overrunning clutch and DIAGNOSIS AND TESTING
starter pinion gear unit to engage and drive a starter
ring gear that is integral to the flywheel (manual STARTING SYSTEM
transmission) or torque converter drive plate (auto-
matic transmission) mounted on the rear crankshaft DIAGNOSIS
flange. Shims are available and can be used to adjust The battery, starting, and charging systems oper-
the 2.5L starter motor mounting position to correct ate with one another, and must be tested as a com-
for improper starter pinion gear to starter ring gear plete system. In order for the vehicle to start and
engagement. charge properly, all of the components involved in
these systems must perform within specifications.
STARTER RELAY Group 8A covers the Battery, Group 8B covers the
Starting Systems, and Group 8C covers the Charging
DESCRIPTION System. We have separated these systems to make it
The starter relay is an electromechanical device easier to locate the information you are seeking
that switches battery current to the pull-in coil of the within this Service Manual. However, when attempt-
starter solenoid when the ignition switch is turned to ing to diagnose any of these systems, it is important
the Start position. The starter relay is located in the that you keep their interdependency in mind.
Power Distribution Center (PDC), in the engine com- The diagnostic procedures used in these groups
partment. See the fuse and relay layout label affixed include the most basic conventional diagnostic meth-
to the inside surface of the PDC cover for starter ods, to the more sophisticated On-Board Diagnostics
relay identification and location. (OBD) built into the Powertrain Control Module
The starter relay is a International Standards (PCM). Use of an induction-type milliampere amme-
Organization (ISO) relay. Relays conforming to the ter, volt/ohmmeter, battery charger, carbon pile rheo-
ISO specifications have common physical dimensions, stat (load tester), and 12-volt test lamp may be
current capacities, terminal patterns, and terminal required.
functions. All OBD-sensed systems are monitored by the
The starter relay cannot be repaired or adjusted PCM. Each monitored circuit is assigned a Diagnos-
and, if faulty or damaged, it must be replaced. tic Trouble Code (DTC). The PCM will store a DTC in
electronic memory for any failure it detects. Refer to
OPERATION On-Board Diagnostic Test For Charging System
The ISO relay consists of an electromagnetic coil, a in the Diagnosis and Testing section of Group 8C -
resistor or diode, and three (two fixed and one mov- Charging System for more information.
able) electrical contacts. The movable (common feed)
DIAGNOSIS AND TESTING (Continued)
Starting System Diagnosis

CONDITION POSSIBLE CAUSE CORRECTION
STARTER FAILS TO 1. Battery discharged or 1. Refer to Battery in the Diagnosis and Testing section of
OPERATE. faulty. Group 8A - Battery. Charge or replace the battery, if
2. Starting circuit wiring required.
faulty. 2. Refer to Starting System in Group 8W - Wiring
3. Starter relay faulty. Diagrams. Test and repair the starter feed and/or control
4. Ignition switch faulty. circuits, if required.
5. Clutch pedal position 3. Refer to Starter Relay in the Diagnosis and Testing
switch faulty. section of this group. Replace the starter relay, if
6. Park/Neutral position required.
switch faulty or 4. Refer to Ignition Switch and Key Lock Cylinder in the
misadjusted. Diagnosis and Testing section of Group 8D - Ignition
7. Starter solenoid faulty. System. Replace the ignition switch, if required.
8. Starter motor faulty. 5. Refer to Clutch Pedal Position Switch in the Diagnosis
and Testing section of Group 6 - Clutch.
6. Refer to Park/Neutral Position Switch in the Diagnosis
and Testing section of Group 21 - Transmission. Replace
the park/neutral position switch, if required.
7. Refer to Starter Motor in the Diagnosis and Testing
section of this group. Replace the starter motor assembly,
if required.
8. If all other starting system components and circuits test
OK, replace the starter motor assembly.
STARTER ENGAGES, 1. Battery discharged or 1. Refer to Battery in the Diagnosis and Testing section of
FAILS TO TURN faulty. Group 8A - Battery. Charge or replace the battery, if
ENGINE. 2. Starting circuit wiring required.
faulty. 2. Refer to Starting System in Group 8W - Wiring
3. Starter motor faulty. Diagrams. Test and repair the starter feed and/or control
4. Engine seized. circuits, if required.
4. Refer to Engine Diagnosis in the Diagnosis and Testing
section of Group 9 - Engine.
STARTER ENGAGES, 1. Starter ring gear faulty. 1. Refer to Starter Motor in the Removal and Installation
SPINS OUT BEFORE 2. Starter motor faulty. section of this group. Remove the starter motor to inspect
ENGINE STARTS. the starter ring gear. Replace the starter ring gear, if
required.
STARTER DOES NOT 1. Starter motor 1. Refer to Starter Motor in the Removal and Installation
DISENGAGE. improperly installed. section of this group. Tighten the starter mounting
2. Starter relay faulty. hardware to the correct tightness specifications.
3. Ignition switch faulty. 2. Refer to Starter Relay in the Diagnosis and Testing
4. Starter motor faulty. section of this group. Replace the starter relay, if
required.
3. Refer to Ignition Switch and Key Lock Cylinder in the
Diagnosis and Testing section of Group 8D - Ignition
System. Replace the ignition switch, if required.
INSPECTION required. Refer to the proper section of Group 8W -
For complete circuit diagrams, refer to Starting Wiring Diagrams for complete service information
System in the Contents of Group 8W - Wiring Dia- and circuit diagrams for the starting system wiring
grams. Before removing any unit from the starting components.
system for repair or diagnosis, perform the following
inspections: TESTING
WARNING: ON VEHICLES EQUIPPED WITH AIR- COLD CRANKING TEST

BAGS, REFER TO GROUP 8M - PASSIVE For complete circuit diagrams, refer to Starting
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY System in the Contents of Group 8W - Wiring Dia-
STEERING WHEEL, STEERING COLUMN, OR grams. The battery must be fully-charged and load-
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR tested before proceeding. Refer to Battery in the
SERVICE. FAILURE TO TAKE THE PROPER PRE- Diagnosis and Testing section of Group 8A - Battery
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- for the procedures.
BAG DEPLOYMENT AND POSSIBLE PERSONAL (1) Connect a suitable volt-ampere tester to the
INJURY. battery terminals (Fig. 1). See the instructions pro-
vided by the manufacturer of the volt-ampere tester
• Battery - Visually inspect the battery for indi- being used.
cations of physical damage and loose or corroded
cable connections. Determine the state-of-charge and
cranking capacity of the battery. Charge or replace
the battery, if required. Refer to Battery in the
proper section of Group 8A - Battery for complete ser-
vice information for the battery.
• Ignition Switch - Visually inspect the ignition
switch for indications of physical damage and loose
or corroded wire harness connections. Refer to Igni-
tion Switch and Key Lock Cylinder in the proper
section of Group 8D - Ignition System for complete
service information for the ignition switch.
• Clutch Pedal Position Switch - If the vehicle
is equipped with a manual transmission, visually
inspect the clutch pedal position switch for indica-
tions of physical damage and loose or corroded wire Fig. 1 Volts-Amps Tester Connections - Typical
harness connections. Refer to Clutch Pedal Posi-
tion Switch in the proper section of Group 6 - (2) Fully engage the parking brake.
Clutch for complete service information for the clutch (3) If the vehicle is equipped with a manual trans-
pedal position switch. mission, place the gearshift selector lever in the Neu-
• Park/Neutral Position Switch - If the vehicle tral position and block the clutch pedal in the fully
is equipped with an automatic transmission, visually depressed position. If the vehicle is equipped with an
inspect the park/neutral position switch for indica- automatic transmission, place the gearshift selector
tions of physical damage and loose or corroded wire lever in the Park position.
harness connections. Refer to Park/Neutral Posi- (4) Verify that all lamps and accessories are
tion Switch in the proper section of Group 21 - turned off.
Transmission for complete service information for the (5) To prevent the engine from starting, remove
park/neutral position switch. the Automatic ShutDown (ASD) relay. The ASD relay
• Starter Relay - Visually inspect the starter is located in the Power Distribution Center (PDC), in
relay for indications of physical damage and loose or the engine compartment. Refer to the fuse and relay
corroded wire harness connections. layout label affixed to the underside of the PDC cover
• Starter Motor - Visually inspect the starter for ASD relay identification and location.
motor for indications of physical damage and loose or (6) Rotate and hold the ignition switch in the Start
corroded wire harness connections. position. Note the cranking voltage and current
• Starter Solenoid - Visually inspect the starter (amperage) draw readings shown on the volt-ampere
solenoid for indications of physical damage and loose tester.
or corroded wire harness connections. (a) If the voltage reads below 9.6 volts, refer to
• Wiring - Visually inspect the wire harnesses for Starter Motor in the Diagnosis and Testing sec-
damage. Repair or replace any faulty wiring, as tion of this group. If the starter motor is OK, refer
to Engine Diagnosis in the Diagnosis and Testing layout label affixed to the underside of the PDC cover
section of Group 9 - Engine for further testing of for ASD relay identification and location.
the engine. If the starter motor is not OK, replace (1) Connect the positive lead of the voltmeter to
the faulty starter motor. the battery negative terminal post. Connect the neg-
(b) If the voltage reads above 9.6 volts and the ative lead of the voltmeter to the battery negative
current (amperage) draw reads below specifica- cable clamp (Fig. 2). Rotate and hold the ignition
tions, refer to Feed Circuit Test in this section. switch in the Start position. Observe the voltmeter. If
(c) If the voltage reads 12.5 volts or greater and voltage is detected, correct the poor contact between
the starter motor does not turn, refer to Control the cable clamp and the terminal post.
Circuit Testing in this section.
(d) If the voltage reads 12.5 volts or greater and
the starter motor turns very slowly, refer to Feed
Circuit Test in this section.
NOTE: A cold engine will increase the starter cur-

rent (amperage) draw reading, and reduce the bat-
tery voltage reading.
FEED CIRCUIT TEST

The starter feed circuit test (voltage drop method)
will determine if there is excessive resistance in the
high-amperage feed circuit. For complete circuit dia-
grams, refer to Starting System in the Contents of
Group 8W - Wiring Diagrams.
When performing these tests, it is important to
remember that the voltage drop is giving an indica- Fig. 2 Test Battery Negative Connection Resistance
tion of the resistance between the two points at - Typical
which the voltmeter probes are attached. (2) Connect the positive lead of the voltmeter to
Example: When testing the resistance of the bat- the battery positive terminal post. Connect the nega-
tery positive cable, touch the voltmeter leads to the tive lead of the voltmeter to the battery positive cable
battery positive cable clamp and the cable connector clamp (Fig. 3). Rotate and hold the ignition switch in
at the starter solenoid. If you probe the battery pos- the Start position. Observe the voltmeter. If voltage
itive terminal post and the cable connector at the is detected, correct the poor contact between the
starter solenoid, you are reading the combined volt- cable clamp and the terminal post.
age drop in the battery positive cable clamp-to-termi-
nal post connection and the battery positive cable.
The following operation will require a voltmeter
accurate to 1/10 (0.10) volt. Before performing the
tests, be certain that the following procedures are
accomplished:
• Battery is fully-charged and load-tested. Refer to
Battery in the Diagnosis and Testing section of
Group 8A - Battery for the procedures.
• Fully engage the parking brake.
• If the vehicle is equipped with a manual trans-
mission, place the gearshift selector lever in the Neu-
tral position and block the clutch pedal in the fully
depressed position. If the vehicle is equipped with an
automatic transmission, place the gearshift selector
lever in the Park position.
• Verify that all lamps and accessories are turned
Fig. 3 Test Battery Positive Connection Resistance -
off.
Typical
• To prevent the engine from starting, remove the
Automatic ShutDown (ASD) relay. The ASD relay is (3) Connect the voltmeter to measure between the
located in the Power Distribution Center (PDC), in battery positive terminal post and the starter sole-
the engine compartment. Refer to the fuse and relay noid battery terminal stud (Fig. 4). Rotate and hold
the ignition switch in the Start position. Observe the
voltmeter. If the reading is above 0.2 volt, clean and
tighten the battery cable connection at the solenoid.
Repeat the test. If the reading is still above 0.2 volt,
replace the faulty battery positive cable.
Fig. 6 Test Starter Ground - Typical

If the resistance tests detect no feed circuit prob-
lems, refer to Starter Motor in the Diagnosis and
Testing section of this group.
Fig. 4 Test Battery Positive Cable Resistance - CONTROL CIRCUIT TESTING

Typical The starter control circuit components should be
(4) Connect the voltmeter to measure between the tested in the order in which they are listed, as fol-
battery negative terminal post and a good clean lows:
ground on the engine block (Fig. 5). Rotate and hold • Starter Relay - Refer to Starter Relay in the
the ignition switch in the Start position. Observe the Diagnosis and Testing section of this group for the
voltmeter. If the reading is above 0.2 volt, clean and procedures.
tighten the battery negative cable attachment on the • Starter Solenoid - Refer to Starter Motor in
engine block. Repeat the test. If the reading is still the Diagnosis and Testing section of this group for
above 0.2 volt, replace the faulty battery negative the procedures.
cable. • Ignition Switch - Refer to Ignition Switch
and Key Lock Cylinder in the Diagnosis and Test-
ing section of Group 8D - Ignition System for the pro-
cedures.
• Clutch Pedal Position Switch - If the vehicle
is equipped with a manual transmission, refer to
Clutch Pedal Position Switch in the Diagnosis
and Testing section of Group 6 - Clutch for the pro-
cedures.
• Park/Neutral Position Switch - If the vehicle
is equipped with an automatic transmission, refer to
Park/Neutral Position Switch in the Diagnosis
and Testing section of Group 21 - Transmission for
the procedures.
• Wire harnesses and connections - Refer to
Starting System in the Contents of Group 8W -
Fig. 5 Test Ground Circuit Resistance - Typical Wiring Diagrams for complete circuit diagrams.
(5) Connect the positive lead of the voltmeter to
the starter housing. Connect the negative lead of the
STARTER MOTOR NOISE - 2.5L ENGINE
See the Starter Motor Noise Diagnosis chart (Fig.
voltmeter to the battery negative terminal post (Fig.
7). If the complaint is similar to Conditions 1 and 2
6). Rotate and hold the ignition switch in the Start
in the chart, correction can be made by placing shims
position. Observe the voltmeter. If the reading is
between the starter motor and the engine block using
above 0.2 volt, correct the poor starter to engine
the following procedures:
block ground contact.
(1) If the complaint is similar to Condition 1, the
starter motor must be moved toward the starter ring
Fig. 7 Starter Motor Noise Diagnosis

gear by removing shims from both starter mounting NOTE: This is a condition that will generally cause
pads on the engine block (Fig. 8). Refer to Starter broken starter (flywheel/torque converter drive
Motor in the Removal and Installation section of plate) ring gear teeth or broken starter motor hous-
this group for the procedures. ings.
NOTE: The shim thickness is 0.381 mm (0.015 in.).

These shims may be stacked if additional thickness STARTER MOTOR
is required. Correct starter motor operation can be confirmed
by performing the following free running bench test.
This test can only be performed with the starter
motor removed from the vehicle. Refer to Starting
System in the Specifications section of this group for
the starter motor specifications.
CAUTION: The 2.5L engine uses a permanent mag-

net starter. Permanent magnet starters are highly
sensitive to hammering, shocks, external pressure
and reverse polarity. This starter motor must never
be clamped in a vise by the starter field frame. The
starter should only be clamped by the mounting
flange. Do not reverse the battery cable connec-
tions to this starter motor when testing. The perma-
nent magnets may be damaged and the starter
rendered unserviceable if it is subjected to any of
these conditions.
Fig. 8 Starter Motor Shim
(2) If the complaint is similar to Condition 2, the (1) Remove the starter motor from the vehicle.
starter motor must be moved away from the starter Refer to Starter Motor in the Removal and Instal-
ring gear. This is done by installing shim(s) across lation section of this group for the procedures.
both starter mounting pads on the engine block. (2) Mount the starter motor securely in a soft-
More than one shim may be required. Refer to jawed bench vise. The vise jaws should be clamped
Starter Motor in the Removal and Installation sec- on the mounting flange of the starter motor. Never
tion of this group for the procedures. clamp on the starter motor by the field frame.
(3) Connect a suitable volt-ampere tester and a
12-volt battery to the starter motor in series, and set
the ammeter to the 100 ampere scale. See the
instructions provided by the manufacturer of the
volt-ampere tester being used.
(4) Install a jumper wire from the solenoid termi-
nal to the solenoid battery terminal. The starter
motor should operate. If the starter motor fails to
operate, replace the faulty starter motor assembly.
(5) Adjust the carbon pile load of the tester to Fig. 10 Continuity Test Between Solenoid Terminal
obtain the free running test voltage. Refer to Start- and Solenoid Case - Typical
ing System in the Specifications section of this ment. Refer to the fuse and relay layout label affixed
group for the starter motor free running test voltage to the underside of the PDC cover for starter relay
specifications. identification and location. For complete circuit dia-
(6) Note the reading on the ammeter and compare grams, refer to Starting System in the Contents of
this reading to the free running test maximum Group 8W - Wiring Diagrams.
amperage draw. Refer to Starting System in the (1) Remove the starter relay from the PDC. Refer
Specifications section of this group for the starter to Starter Relay in the Removal and Installation
motor free running test maximum amperage draw section of this group for the procedures.
specifications. (2) A relay in the de-energized position should
(7) If the ammeter reading exceeds the maximum have continuity between terminals 87A and 30, and
amperage draw specification, replace the faulty no continuity between terminals 87 and 30. If OK, go
starter motor assembly. to Step 3. If not OK, replace the faulty relay.
(3) Resistance between terminals 85 and 86 (elec-
STARTER SOLENOID tromagnet) should be 75 6 5 ohms. If OK, go to Step
This test can only be performed with the starter 4. If not OK, replace the faulty relay.
motor removed from the vehicle. (4) Connect a battery to terminals 85 and 86.
(1) Remove the starter motor from the vehicle. There should now be continuity between terminals
Refer to Starter Motor in the Removal and Instal- 30 and 87, and no continuity between terminals 87A
lation section of this group for the procedures. and 30. If OK, perform the Relay Circuit Test that
(2) Disconnect the wire from the solenoid field coil follows. If not OK, replace the faulty relay.
terminal.
(3) Check for continuity between the solenoid ter-
minal and the solenoid field coil terminal with a con-
tinuity tester (Fig. 9). There should be continuity. If
OK, go to Step 4. If not OK, replace the faulty starter
motor assembly.
Fig. 9 Continuity Test Between Solenoid Terminal

and Field Coil Terminal - Typical
Fig. 11 Starter Relay
(4) Check for continuity between the solenoid ter-
minal and the solenoid case (Fig. 10). There should RELAY CIRCUIT TEST
be continuity. If not OK, replace the faulty starter (1) The relay common feed terminal cavity (30) is
motor assembly. connected to battery voltage and should be hot at all
times. If OK, go to Step 2. If not OK, repair the open
STARTER RELAY circuit to the fuse in the PDC as required.
The starter relay (Fig. 11) is located in the Power
Distribution Center (PDC), in the engine compart-
(2) The relay normally closed terminal (87A) is REMOVAL AND INSTALLATION
connected to terminal 30 in the de-energized position,
but is not used for this application. Go to Step 3. STARTER MOTOR
(3) The relay normally open terminal (87) is con-
nected to the common feed terminal (30) in the ener- REMOVAL
gized position. This terminal supplies battery voltage
to the starter solenoid field coils. There should be 2.5L ENGINE
continuity between the cavity for relay terminal 87 (1) Disconnect and isolate the battery negative
and the starter solenoid terminal at all times. If OK, cable.
go to Step 4. If not OK, repair the open circuit to the (2) Raise and support the vehicle.
starter solenoid as required. (3) While supporting the starter motor with one
(4) The coil battery terminal (86) is connected to hand, use the other hand to remove the two screws
the electromagnet in the relay. It is energized when that secure the starter motor to the engine block
the ignition switch is held in the Start position. On (Fig. 12).
vehicles with a manual transmission, the clutch
pedal must be fully depressed for this test. Check for
battery voltage at the cavity for relay terminal 86
with the ignition switch in the Start position, and no
voltage when the ignition switch is released to the
On position. If OK, go to Step 5. If not OK with an
automatic transmission, check for an open or short
circuit to the ignition switch and repair, if required.
If the circuit to the ignition switch is OK, refer to
Ignition Switch and Key Lock Cylinder in the
Diagnosis and Testing section of Group 8D - Ignition
System for testing of the ignition switch. If not OK
with a manual transmission, check the circuit
between the relay and the clutch pedal position
switch for an open or a short. If the circuit is OK,
refer to Clutch Pedal Position Switch in the Diag-
nosis and Testing section of Group 6 - Clutch for test-
ing of the switch.
(5) The coil ground terminal (85) is connected to
the electromagnet in the relay. On vehicles with a
manual transmission, it is grounded at all times. On
vehicles with an automatic transmission, it is
grounded through the park/neutral position switch
only when the gearshift selector lever is in the Park
Fig. 12 Starter Motor Remove/Install - 2.5L Engine
or Neutral positions. Check for continuity to ground (4) Lower the starter motor from the engine block
at the cavity for relay terminal 85. If not OK with a far enough to access and remove the nut that secures
manual transmission, repair the circuit to ground as the solenoid wire harness connector eyelet to the
required. If not OK with an automatic transmission, solenoid terminal stud. Always support the starter
check for an open or short circuit to the park/neutral motor during this process, do not let the starter
position switch and repair, if required. If the circuit motor hang from the wire harness.
to the park/neutral position switch is OK, refer to (5) Remove the nut that secures the battery cable
Park/Neutral Position Switch in the Diagnosis harness connector eyelet to the solenoid battery ter-
and Testing section of Group 21 - Transmission for minal stud. Always support the starter motor during
testing of the park/neutral position switch. this process, do not let the starter motor hang from
the wire harness.
(6) Remove the battery cable and solenoid wire
connector eyelets from the solenoid terminal studs.
(7) Remove the starter motor and any starter
motor shims (if used) from the engine compartment.
REMOVAL AND INSTALLATION (Continued)
4.0L ENGINE
(1) Disconnect and isolate the battery negative
cable.
(2) Raise and support the vehicle.
(3) Remove the lower (forward facing) mounting
screw from the starter motor (Fig. 13).
Fig. 14 Starter Wire Harness Remove/Install - 4.0L

Engine
(2) Install the battery cable and solenoid wire con-
nector eyelets onto the solenoid terminal studs.
(3) Install and tighten the nut that secures the
battery cable harness connector eyelet to the solenoid
battery terminal stud. Tighten the nut to 10 N·m (90
in. lbs.). Always support the starter motor during
this process, do not let the starter motor hang from
the wire harness.
solenoid wire harness connector eyelet to the solenoid
Fig. 13 Starter Motor Remove/Install - 4.0L Engine terminal stud. Tighten the nut to 6 N·m (55 in. lbs.).
Always support the starter motor during this process,
(4) While supporting the starter motor with one
do not let the starter motor hang from the wire har-
hand, use the other hand to remove the upper (rear
ness.
facing) mounting screw from the starter motor.
(5) Position the starter motor and any starter
(5) Lower the starter motor from the front of the
motor shims that were removed to the engine block
transmission clutch housing or torque converter
and loosely install both of the mounting screws.
housing far enough to access and remove the nut
that secures the battery cable eyelet to the solenoid NOTE: Shim thickness available is 0.381 mm (0.015
battery terminal (Fig. 14). Always support the starter in.). Refer to Starter Motor Noise - 2.5L Engine in
motor during this process, do not let the starter the Diagnosis and Testing section of this group for
motor hang from the wire harness. more information.
(6) Remove the battery cable eyelet from the sole-
noid battery terminal. Always support the starter (6) Tighten both of the starter motor mounting
motor during this process, do not let the starter screws. Tighten the screws to 45 N·m (33 ft. lbs.).
motor hang from the wire harness. (7) Lower the vehicle.
(7) Disconnect the solenoid terminal wire harness (8) Reconnect the battery negative cable.
connector from the connector receptacle on the
starter solenoid. Always support the starter motor 4.0L ENGINE
during this process, do not let the starter motor hang (1) Position the starter motor in the engine com-
from the wire harness. partment.
(8) Remove the starter motor from the engine com- (2) Reconnect the solenoid terminal wire harness
partment. connector to the connector receptacle on the starter
solenoid. Always support the starter motor during
INSTALLATION this process, do not let the starter motor hang from
the wire harness.
2.5L ENGINE (3) Install the battery cable eyelet onto the sole-
(1) Position the starter motor in the engine com- noid battery terminal. Always support the starter
partment.
motor during this process, do not let the starter (3) See the fuse and relay layout label affixed to
motor hang from the wire harness. the underside of the PDC cover for starter relay iden-
(4) Install and tighten the nut that secures the tification and location.
battery cable eyelet to the solenoid battery terminal. (4) Remove the starter relay from the PDC.
Tighten the nut to 10 N·m (90 in. lbs.). Always sup-
port the starter motor during this process, do not let INSTALLATION
the starter motor hang from the wire harness. (1) See the fuse and relay layout label affixed to
(5) Position the starter motor to the front of the the underside of the PDC cover for the proper starter
transmission clutch housing or torque converter relay location.
housing and loosely install both the upper and lower (2) Position the starter relay in the proper recep-
mounting screws. tacle in the PDC.
(6) Tighten the lower (forward facing) starter (3) Align the starter relay terminals with the ter-
motor mounting screw. Tighten the screw to 41 N·m minal cavities in the PDC receptacle.
(30 ft. lbs.). (4) Push down firmly on the starter relay until the
(7) Tighten the upper (rearward facing) starter terminals are fully seated in the terminal cavities in
motor mounting screw. Tighten the screw to 54 N·m the PDC receptacle.
(40 ft. lbs.). (5) Install the cover onto the PDC.
(8) Lower the vehicle. (6) Reconnect the battery negative cable.
(9) Reconnect the battery negative cable.
STARTER RELAY
REMOVAL
cable.
(2) Remove the cover from the Power Distribution
Center (PDC) (Fig. 15).
Fig. 15 Power Distribution Center

SPECIFICATIONS
STARTING SYSTEM
Starter Motor and Solenoid

Manufacturer Mitsubishi
Engine Application 2.5L, 4.0L
2.5L - 1.2 Kilowatt (1.6 Horsepower)
Power Rating
4.0L - 1.4 Kilowatt (1.9 Horsepower)
Voltage 12 Volts
Number of Fields 4
Number of Poles 4
Number of Brushes 4
Drive Type Planetary Gear Reduction
Free Running Test Voltage 11.2 Volts
Free Running Test Maximum Amperage Draw 90 Amperes
2.5L - 2600 rpm
Free Running Test Minimum Speed
4.0L - 2500 rpm
Solenoid Closing Maximum Voltage Required 7.8 Volts
2.5L - 130 Amperes
*Cranking Amperage Draw Test
4.0L - 160 Amperes
*Test at operating temperature. Cold engine, tight (new) engine, or heavy oil will increase starter amperage draw.
TJ CHARGING SYSTEM 8C - 1
CHARGING SYSTEM
CONTENTS
page page
DESCRIPTION AND OPERATION ON-BOARD DIAGNOSTIC TEST FOR

BATTERY TEMPERATURE SENSOR . . . . . . . . . . 2 CHARGING SYSTEM . . . . . . . . . . . . . . . . . . . . 3
CHARGING SYSTEM OPERATION . . . . . . . . . . . 1 REMOVAL AND INSTALLATION
ELECTRONIC VOLTAGE REGULATOR . . . . . . . . . 2 BATTERY TEMPERATURE SENSOR . . . . . . . . . . 3
GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DIAGNOSIS AND TESTING SPECIFICATIONS
BATTERY TEMPERATURE SENSOR . . . . . . . . . . 2 GENERATOR RATINGS . . . . . . . . . . . . . . . . . . . . 5
CHARGING SYSTEM . . . . . . . . . . . . . . . . . . . . . . 2 TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . 5
DESCRIPTION AND OPERATION ground path to control the strength of the rotor mag-
netic field. The PCM then compensates and regulates
CHARGING SYSTEM OPERATION generator current output accordingly.
The charging system consists of: All vehicles are equipped with On-Board Diagnos-
• Generator tics (OBD). All OBD-sensed systems, including EVR
• Electronic Voltage Regulator (EVR) circuitry (field control) circuitry, are monitored by the PCM.
within the Powertrain Control Module (PCM) Each monitored circuit is assigned a Diagnostic Trou-
• Ignition switch (refer to Group 8D, Ignition Sys- ble Code (DTC). The PCM will store a DTC in elec-
tem for information) tronic memory for certain failures it detects. Refer to
• Battery (refer to Group 8A, Battery for informa- On-Board Diagnostics in Group 25, Emission Control
tion) System for more DTC information.
• Battery temperature sensor The Check Gauges Lamp (if equipped) monitors:
• Generator Lamp (if equipped) charging system voltage, engine coolant tempera-
• Check Gauges Lamp (if equipped) ture and engine oil pressure. If an extreme condition
• Voltmeter (refer to Group 8E, Instrument Panel is indicated, the lamp will be illuminated. This is
and Gauges for information) done as reminder to check the three gauges. The sig-
• Wiring harness and connections (refer to Group nal to activate the lamp is sent via the CCD bus cir-
8W, Wiring for information) cuits. The lamp is located on the instrument panel.
The charging system is turned on and off with the Refer to Group 8E, Instrument Panel and Gauges for
ignition switch. The system is on when the engine is additional information.
running and the ASD relay is energized. When the
ASD relay is on, voltage is supplied to the ASD relay GENERATOR
sense circuit at the PCM. This voltage is connected The generator is belt-driven by the engine using a
through the PCM and supplied to one of the genera- serpentine type drive belt. It is serviced only as a
tor field terminals (Gen. Source +) at the back of the complete assembly. If the generator fails for any rea-
generator. son, the entire assembly must be replaced.
The amount of DC current produced by the gener- As the energized rotor begins to rotate within the
ator is controlled by the EVR (field control) circuitry generator, the spinning magnetic field induces a cur-
contained within the PCM. This circuitry is con- rent into the windings of the stator coil. Once the
nected in series with the second rotor field terminal generator begins producing sufficient current, it also
and ground. provides the current needed to energize the rotor.
A battery temperature sensor, located in the bat- The Y type stator winding connections deliver the
tery tray housing, is used to sense battery tempera- induced AC current to 3 positive and 3 negative
ture. This temperature data, along with data from diodes for rectification. From the diodes, rectified DC
monitored line voltage, is used by the PCM to vary current is delivered to the vehicle electrical system
the battery charging rate. This is done by cycling the through the generator battery terminal.
8C - 2 CHARGING SYSTEM TJ
Although the generators appear the same exter- • an undercharged or overcharged battery condi-
nally, different generators with different output rat- tion occurs.
ings are used on this vehicle. Be certain that the Remember that an undercharged battery is often
replacement generator has the same output rating caused by:
and part number as the original unit. Refer to Gen- • accessories being left on with the engine not
erator Ratings in the Specifications section at the running
back of this group for amperage ratings and part • a faulty or improperly adjusted switch that
numbers. allows a lamp to stay on. See Ignition-Off Draw Test
Noise emitting from the generator may be caused in Group 8A, Battery for more information.
by: worn, loose or defective bearings; a loose or defec-
tive drive pulley; incorrect, worn, damaged or misad- INSPECTION
justed fan drive belt; loose mounting bolts; a To perform a complete test of the charging system,
misaligned drive pulley or a defective stator or diode. refer to the appropriate Powertrain Diagnostic Proce-
dures service manual and the DRB scan tool. Per-
BATTERY TEMPERATURE SENSOR form the following inspections before attaching the
The battery temperature sensor is used to deter- scan tool.
mine the battery temperature and control battery (1) Inspect the battery condition. Refer to Group
charging rate. This temperature data, along with 8A, Battery for procedures.
data from monitored line voltage, is used by the PCM (2) Inspect condition of battery cable terminals,
to vary the battery charging rate. System voltage will battery posts, connections at engine block, starter
be higher at colder temperatures and is gradually solenoid and relay. They should be clean and tight.
reduced at warmer temperatures. Repair as required.
(3) Inspect all fuses in both the fuseblock and
ELECTRONIC VOLTAGE REGULATOR Power Distribution Center (PDC) for tightness in
receptacles. They should be properly installed and
DESCRIPTION tight. Repair or replace as required.
The Electronic Voltage Regulator (EVR) is not a (4) Inspect generator mounting bolts for tightness.
separate component. It is actually a voltage regulat- Replace or tighten bolts if required. Refer to the Gen-
ing circuit located within the Powertrain Control erator Removal/Installation section of this group for
Module (PCM). The EVR is not serviced separately. If torque specifications.
replacement is necessary, the PCM must be replaced. (5) Inspect generator drive belt condition and ten-
sion. Tighten or replace belt as required. Refer to
OPERATION Belt Tension Specifications in Group 7, Cooling Sys-
The amount of DC current produced by the gener- tem.
ator is controlled by EVR circuitry contained within (6) Inspect automatic belt tensioner (if equipped).
the PCM. This circuitry is connected in series with Refer to Group 7, Cooling System for information.
the generators second rotor field terminal and its (7) Inspect generator electrical connections at gen-
ground. erator field, battery output, and ground terminal (if
Voltage is regulated by cycling the ground path to equipped). Also check generator ground wire connec-
control the strength of the rotor magnetic field. The tion at engine (if equipped). They should all be clean
EVR circuitry monitors system line voltage and bat- and tight. Repair as required.
tery temperature (refer to Battery Temperature Sen-
sor for more information). It then compensates and BATTERY TEMPERATURE SENSOR
regulates generator current output accordingly. Also To perform a complete test of this sensor and its
refer to Charging System Operation for additional circuitry, refer to the appropriate Powertrain Diag-
information. nostic Procedures manual. To test the sensor only,
refer to the following:
DIAGNOSIS AND TESTING (1) The sensor is located under the battery and is
attached to the battery tray (Fig. 1). A two-wire pig-
CHARGING SYSTEM tail harness is attached directly to the sensor. The
The following procedures may be used to diagnose opposite end of this harness connects the sensor to
the charging system if: the engine wiring harness.
• the generator lamp (if equipped) is illuminated (2) Disconnect the two-wire pigtail harness from
with the engine running the engine harness.
• the voltmeter (if equipped) does not register (3) Attach ohmmeter leads to the wire terminals of
properly the pigtail harness.
(3) Remove generator pivot and mounting bolts/nut
(Fig. 2). Position generator for access to wire connec-
tors.
(4) If equipped, unsnap plastic cover from B+ ter-
minal.
(5) Remove B+ terminal mounting nut at rear of
generator (Fig. 3). Disconnect terminal from genera-
tor.
(6) Disconnect field wire connector at rear of gen-
erator by pushing on connector tab.
(7) Remove generator from vehicle.
INSTALLATION
(1) Position generator to engine and snap field
wire connector into rear of generator.
(2) Install B+ terminal to generator mounting
Fig. 1 Battery Temperature Sensor Location stud. Tighten mounting nut to 8.5 N·m (75 in. lbs.)
(4) At room temperature of 25° C (75–80° F), an torque.
ohmmeter reading of 9,000 (9K) to 11,000 (11K) ohms (3) If equipped, snap plastic cover to B+ terminal.
should be observed. (4) Install generator mounting fasteners and
(5) If reading is above or below the specification, tighten as follows:
replace the sensor. • Generator mounting bolt—55 N·m (41 ft. lbs.)
(6) Refer to the Removal and Installation section torque.
for procedures. • Generator pivot bolt/nut—55 N·m (41 ft. lbs.)
torque.
ON-BOARD DIAGNOSTIC TEST FOR CHARGING CAUTION: Never force a belt over a pulley rim
SYSTEM using a screwdriver. The synthetic fiber of the belt
The Powertrain Control Module (PCM) monitors can be damaged.
critical input and output circuits of the charging sys-
tem, making sure they are operational. A Diagnostic
Trouble Code (DTC) is assigned to each input and CAUTION: When installing a serpentine accessory
output circuit monitored by the On-Board Diagnostic drive belt, the belt MUST be routed correctly. The
(OBD) system. Some circuits are checked continu- water pump will be rotating in the wrong direction if
ously and some are checked only under certain con- the belt is installed incorrectly, causing the engine
ditions. to overheat. Refer to belt routing label in engine
For DTC information, refer to Diagnostic Trouble compartment, or refer to Belt Schematics in Group
Codes in Group 25, Emission Control System. This 7, Cooling System.
will include a complete list of DTC’s including DTC’s
for the charging system. (5) Install generator drive belt. Refer to Group 7,
Cooling System for procedure.
(6) Install negative battery cable to battery.
REMOVAL AND INSTALLATION
BATTERY TEMPERATURE SENSOR
GENERATOR The battery temperature sensor is located under
the vehicle battery and is attached to a mounting
REMOVAL hole on battery tray.
WARNING: DISCONNECT NEGATIVE CABLE FROM REMOVAL

BATTERY BEFORE REMOVING BATTERY OUTPUT (1) Remove battery. Refer to Group 8A, Battery for
WIRE (B+ WIRE) FROM GENERATOR. FAILURE TO procedures.
DO SO CAN RESULT IN INJURY OR DAMAGE TO (2) Disconnect sensor pigtail harness from engine
ELECTRICAL SYSTEM. wire harness.
(3) Pry sensor straight up from battery tray
(1) Disconnect negative battery cable at battery. mounting hole.
(2) Remove generator drive belt. Refer to Group 7,
Cooling System for procedure.
8C - 4 CHARGING SYSTEM TJ
Fig. 2 Generator Remove/Install
Fig. 4 Battery Temperature Sensor Remove/Install

INSTALLATION
(1) Feed pigtail harness through hole in top of bat-
Fig. 3 Generator Connectors (Typical)
tery tray and press sensor into top of battery tray.
(2) Connect pigtail harness.
(3) Install battery. Refer to Group 8A, Battery for
procedures.
SPECIFICATIONS
GENERATOR RATINGS
TYPE PART NUMBER RATED SAE AMPS ENGINES MINIMUM TEST AMPS
DENSO 56005684AB 81 2.5L/4.0L 57
DENSO 56005685AB 117 2.5L/4.0L 88
TORQUE CHART
Description Torque
Generator Upper Mounting Bolt/Nut—
2.5L/4.0L Engine . . . . . . . . . . . . . . . . . . . 55 N·m
(41 ft. lbs.)
Generator Lower Mounting Bolt—
2.5L/4.0L Engine . . . . . . . . . . . . . . . . . . . 55 N·m
(41 ft. lbs.)
Battery Terminal Nut . . . . . . . . . . . . . . . . . 8.5 N·m
(75 in. lbs.)
Ground Terminal Nut . . . . . . . . . . . . . . . . . 8.5 N·m
(75 in. lbs.)
Harness Hold-down Nut . . . . . . . . . . . . . . . 8.5 N·m
(75 in. lbs.)
Field Terminal Nuts . . . . . . . . . . . . . . . . . . 2.8 N·m
(25 in. lbs.)
TJ IGNITION SYSTEM 8D - 1
IGNITION SYSTEM
CONTENTS
page page
DESCRIPTION AND OPERATION SPARK PLUG CONDITIONS . . . . . . . . . . . . . . . . 8

AUTOMATIC SHUTDOWN (ASD) RELAY . . . . . . 2 REMOVAL AND INSTALLATION
CAMSHAFT POSITION SENSOR . . . . . . . . . . . . . 4 CAMSHAFT POSITION SENSOR . . . . . . . . . . . . 13
CRANKSHAFT POSITION SENSOR . . . . . . . . . . . 3 CRANKSHAFT POSITION SENSOR . . . . . . . . . . 12
DISTRIBUTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DISTRIBUTOR . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IGNITION COIL . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IGNITION COIL . . . . . . . . . . . . . . . . . . . . . . . . . 11
IGNITION SWITCH AND KEY LOCK IGNITION SWITCH AND KEY CYLINDER . . . . . 17
CYLINDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SHIFTER/IGNITION INTERLOCK . . . . . . . . . . . . 19
IGNITION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . 1 SPARK PLUG CABLE REMOVAL . . . . . . . . . . . 10
POWERTRAIN CONTROL MODULE . . . . . . . . . . 1 SPARK PLUGS . . . . . . . . . . . . . . . . . . . . . . . . . 10
SPARK PLUG CABLES . . . . . . . . . . . . . . . . . . . . 2 SPECIFICATIONS
SPARK PLUGS . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ENGINE FIRING ORDER—2.5L 4-CYLINDER
DIAGNOSIS AND TESTING ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AUTOMATIC SHUTDOWN (ASD) RELAY TEST . 5 ENGINE FIRING ORDER—4.0L 6-CYLINDER
CAMSHAFT POSITION SENSOR . . . . . . . . . . . . . 7 ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CRANKSHAFT POSITION SENSOR . . . . . . . . . . . 7 IGNITION COIL RESISTANCE . . . . . . . . . . . . . . 20
DISTRIBUTOR CAP . . . . . . . . . . . . . . . . . . . . . . . 6 IGNITION TIMING . . . . . . . . . . . . . . . . . . . . . . . 19
DISTRIBUTOR ROTOR . . . . . . . . . . . . . . . . . . . . 6 SPARK PLUG CABLE RESISTANCE . . . . . . . . . 20
IGNITION COIL TEST . . . . . . . . . . . . . . . . . . . . . 5 SPARK PLUGS . . . . . . . . . . . . . . . . . . . . . . . . . 20
IGNITION TIMING . . . . . . . . . . . . . . . . . . . . . . . . 6 TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . 20
SPARK PLUG CABLES . . . . . . . . . . . . . . . . . . . . 7
DESCRIPTION AND OPERATION

IGNITION SYSTEM
The ignition systems used on the 2.5L 4–cylinder
and the 4.0L 6–cylinder engine are basically identi-
cal. Similarities and differences between the systems
will be discussed.
The ignition system is controlled by the powertrain
control module (PCM) on all engines.
The ignition system consists of:
• Spark Plugs
• Ignition Coil
• Secondary Ignition Cables
• Distributor (contains rotor and camshaft position
sensor)
• Powertrain Control Module (PCM)
• Crankshaft Position, Camshaft Position, Throt-
tle Position and MAP Sensors
POWERTRAIN CONTROL MODULE

The Powertrain Control Module (PCM) is located
in the engine compartment (Fig. 1).
The ignition system is controlled by the PCM. Fig. 1 Powertrain Control Module (PCM) Location
8D - 2 IGNITION SYSTEM TJ
NOTE: Base ignition timing by rotation of distribu- Distributor position will have no effect on igni-
tor is not adjustable. tion timing. The position of the distributor will
determine fuel synchronization only.
The PCM opens and closes the ignition coil ground All distributors contain an internal oil seal that
circuit to operate the ignition coil. This is done to prevents oil from entering the distributor housing.
adjust ignition timing, both initial (base) and The seal is not serviceable.
advance, and for changing engine operating condi-
tions. SPARK PLUGS
The amount of electronic spark advance provided All engines use resistor type spark plugs. Remove
by the PCM is determined by five input factors: the spark plugs and examine them for burned elec-
engine coolant temperature, engine rpm, intake man- trodes and fouled, cracked or broken porcelain insu-
ifold temperature, manifold absolute pressure and lators. Keep plugs arranged in the order in which
throttle position. they were removed from the engine. A single plug
displaying an abnormal condition indicates that a
DISTRIBUTOR problem exists in the corresponding cylinder. Replace
All engines are equipped with a camshaft driven spark plugs at the intervals recommended in Group
mechanical distributor containing a shaft driven dis- O, Lubrication and Maintenance.
tributor rotor. All distributors are equipped with an Spark plugs that have low milage may be cleaned
internal camshaft position (fuel sync) sensor (Fig. 2). and reused if not otherwise defective, carbon or oil
This sensor provides fuel injection synchronization fouled. Refer to the Spark Plug Condition section of
and cylinder identification. this group.
SPARK PLUG CABLES

Spark plug cables are sometimes referred to as sec-
ondary ignition wires. These cables transfer electrical
current from the ignition coil(s) and/or distributor, to
individual spark plugs at each cylinder. The resistive
spark plug cables are of nonmetallic construction.
The cables provide suppression of radio frequency
emissions from the ignition system.
IGNITION COIL
Battery voltage is supplied to the ignition coil pos-
itive terminal from the ASD relay.
The Powertrain Control Module (PCM) opens and
closes the ignition coil ground circuit for ignition coil
operation.
Fig. 2 Distributor and Camshaft Position Sensor- Base ignition timing is not adjustable on any
Typical engine. By controlling the coil ground circuit, the
PCM is able to set the base timing and adjust the
The distributors on both the 2.5L 4-cylinder and
ignition timing advance. This is done to meet chang-
the 4.0L-6 cylinder engines do not have built in cen-
ing engine operating conditions.
trifugal or vacuum assisted advance. Base ignition
The ignition coil is not oil filled. The windings are
timing and all timing advance is controlled by the
embedded in an epoxy compound. This provides heat
powertrain control module (PCM). Because ignition
and vibration resistance that allows the ignition coil
timing is controlled by the PCM, base ignition tim-
to be mounted on the engine.
ing is not adjustable on any of these engines.
The distributor is locked in place by a fork with a
slot located on the distributor housing base. The dis-
AUTOMATIC SHUTDOWN (ASD) RELAY
tributor holddown clamp bolt passes through this slot As one of its functions, the ASD relay will supply
when installed. Because the distributor position is battery voltage to the ignition coil. The ground cir-
locked when installed, its rotational position can not cuit for the ASD relay is controlled by the Powertrain
be changed. Do not attempt to modify the dis- Control Module (PCM). The PCM regulates ASD
tributor housing to get distributor rotation. relay operation by switching the ground circuit
on-and-off.
CRANKSHAFT POSITION SENSOR

The crankshaft position sensor is mounted to the
transmission bellhousing at the left/rear side of the
engine block (Fig. 3), (Fig. 4), or (Fig. 5).
Fig. 5 Crankshaft Position Sensor—Manual

Transmission (Typical)
Fig. 3 Crankshaft Position Sensor—4.0L 6-Cyl.
Engine—Auto. Trans. Engine speed and crankshaft position are provided
through the crankshaft position sensor. The sensor
generates pulses that are the input sent to the pow-
ertrain control module (PCM). The PCM interprets
the sensor input to determine the crankshaft posi-
tion. The PCM then uses this position, along with
other inputs, to determine injector sequence and igni-
tion timing.
The sensor is a hall effect device combined with an
internal magnet. It is also sensitive to steel within a
certain distance from it.
SENSOR OPERATION
The flywheel/drive plate has groups of four notches
at its outer edge. On 4.0L 6-cylinder engines there
are three sets of notches (Fig. 7) or (Fig. 8). On 2.5L
4-cylinder engines there are two sets of notches (Fig.
6).
The notches cause a pulse to be generated when
they pass under the sensor. The pulses are the input
to the PCM. For each engine revolution there are two
groups of four pulses generated on 2.5L 4-cylinder
engines. There are 3 groups of four pulses generated
on 4.0L 6-cylinder engines.
Fig. 4 Crankshaft Position Sensor—2.5L 4-Cyl. The trailing edge of the fourth notch, which causes
Engine—Auto. Trans. the pulse, is four degrees before top dead center
(TDC) of the corresponding piston.
The engine will not operate if the PCM does not
receive a crankshaft position sensor input.
Fig. 6 Sensor Operation—2.5L 4-Cyl. Engine Fig. 8 Sensor Operation—4.0L 6-Cyl. Engine—
Automatic Transmission
The sensor contains a hall effect device called a
sync signal generator to generate a fuel sync signal.
This sync signal generator detects a rotating pulse
ring (shutter) on the distributor shaft. The pulse ring
rotates 180 degrees through the sync signal genera-
tor. Its signal is used in conjunction with the crank-
shaft position sensor to differentiate between fuel
injection and spark events. It is also used to synchro-
nize the fuel injectors with their respective cylinders.
When the leading edge of the pulse ring (shutter)
enters the sync signal generator, the following occurs:
The interruption of magnetic field causes the voltage
to switch high resulting in a sync signal of approxi-
mately 5 volts.
When the trailing edge of the pulse ring (shutter)
leaves the sync signal generator, the following occurs:
The change of the magnetic field causes the sync sig-
nal voltage to switch low to 0 volts.
IGNITION SWITCH AND KEY LOCK CYLINDER

The ignition switch is located on the steering col-
Fig. 7 Sensor Operation—4.0L 6-Cyl. Engine—
umn. The Key-In-Switch is located in the ignition
Manual Transmission
switch module. For electrical diagnosis of the Key-In-
CAMSHAFT POSITION SENSOR Switch, refer to Group 8U, Chime/Buzzer Warning
The camshaft position sensor is located in the dis- Systems. For removal/installation of either the key
tributor on all engines. lock cylinder or ignition switch, refer to Ignition
Switch and Key Cylinder in this group.
On vehicles equipped with an automatic transmis-
sion, a cable connects an interlock device within the
steering column assembly to the transmission floor
shift lever. This interlock device is used to lock the
transmission shifter in the PARK position when the
key is in the LOCKED or ACCESSORY position. The
interlock device is not serviceable. If repair is neces-
sary, the steering column assembly must be replaced.
Refer to Group 19, Steering for procedures. The
shifter interlock cable can be adjusted or replaced.
Refer to Group 21, Transmissions for procedures.
On vehicles equipped with a manual transmission,
a lever is located on the steering column behind the
ignition key lock cylinder. The lever must be operated
to allow rotation of the ignition key lock cylinder. The
lever mechanism is not serviced separately. If repair
is necessary, the steering column assembly must be
replaced. Refer to Group 19, Steering for procedures.
Fig. 9 Ignition Coil—2.5L Engine

DIAGNOSIS AND TESTING
AUTOMATIC SHUTDOWN (ASD) RELAY TEST
To perform a complete test of this relay and its cir-
cuitry, refer to the DRB scan tool. Also refer to the
appropriate Powertrain Diagnostics Procedures man-
ual. To test the relay only, refer to Relays—Opera-
tion/Testing in the Group 14, Fuel Systems section.
IGNITION COIL TEST

To perform a complete test of the ignition coil and
its circuitry, refer to the DRB scan tool. Also refer to
the appropriate Powertrain Diagnostics Procedures
manual. To test the coil only, refer to the following:
The ignition coil (Fig. 9) or (Fig. 10) is designed to
operate without an external ballast resistor.
Inspect the ignition coil for arcing. Test the coil
according to coil tester manufacturer’s instructions.
Test the coil primary and secondary resistance.
Replace any coil that does not meet specifications.
Refer to the IGNITION COIL RESISTANCE chart.
IGNITION COIL RESISTANCE
PRIMARY RESISTANCE SECONDARY RESISTANCE

COIL MANUFACTURER
21-27°C (70-80°F) 21-27°C (70-80°F)
Diamond 0.97 - 1.18 Ohms 11,300 - 15,300 Ohms
Toyodenso 0.95 - 1.20 Ohms 11,300 - 13,300 Ohms
If the ignition coil is being replaced, the secondary
spark plug cable must also be checked. Replace cable
if it has been burned or damaged.
Arcing at the tower will carbonize the cable boot,
which if it is connected to a new ignition coil, will
cause the coil to fail.
If the secondary coil cable shows any signs of dam-
age, it should be replaced with a new cable and new
terminal. Carbon tracking on the old cable can cause
arcing and the failure of a new ignition coil.
DISTRIBUTOR CAP
Remove the distributor cap and wipe it clean with
a dry lint free cloth. Visually inspect the cap for
cracks, carbon paths, broken towers or damaged
rotor button (Fig. 11) or (Fig. 12). Also check for
white deposits on the inside (caused by condensation Fig. 12 Cap Inspection—Internal—Typical
entering the cap through cracks). Replace any cap
that displays charred or eroded terminals. The
machined surface of a terminal end (faces toward
rotor) will indicate some evidence of erosion from
normal operation. Examine the terminal ends for evi-
dence of mechanical interference with the rotor tip.
Fig. 13 Rotor Inspection—Typical

IGNITION TIMING
Fig. 11 Cap Inspection—External—Typical
NOTE: Base (initial) ignition timing is NOT adjust-
DISTRIBUTOR ROTOR able on any 2.5L 4-cylinder or 4.0L 6-cylinder
Visually inspect the rotor (Fig. 13) for cracks, evi- engine. Do not attempt to adjust ignition timing by
dence of corrosion or the effects of arcing on the rotating the distributor.
metal tip. Also check for evidence of mechanical
interference with the cap. Some charring is normal
on the end of the metal tip. The silicone-dielectric- NOTE: Do not attempt to modify the distributor
varnish-compound applied to the rotor tip for radio housing to get distributor rotation. Distributor posi-
interference noise suppression, will appear charred. tion will have no effect on ignition timing.
This is normal. Do not remove the charred com-
pound. Test the spring for insufficient tension. All ignition timing functions are controlled by the
Replace a rotor that displays any of these adverse powertrain control module (PCM). For additional
conditions. information, refer to the appropriate Powertrain
Diagnostics Procedures service manual for operation
of the DRB Scan Tool.
CRANKSHAFT POSITION SENSOR (7) If voltage is still not present, check for voltage
To perform a complete test of this sensor and its at the supply wire. For wire identification, refer to
circuitry, refer to the DRB scan tool. Also refer to the Group 8W, Wiring Diagrams.
appropriate Powertrain Diagnostics Procedures man- (8) If 5 volts is not present at supply wire, check
ual. for voltage at PCM 32-way connector (cavity A-17).
Refer to Group 8W, Wiring for location of connector/
CAMSHAFT POSITION SENSOR terminal. Leave the PCM connector connected for
The camshaft position sensor is located in the dis- this test.
tributor (Fig. 14) on all engines. (9) If voltage is still not present, perform vehicle
test using the DRB scan tool.
(10) If voltage is present at cavity A-17, but not at
the supply wire:
(a) Check continuity between the supply wire.
This is checked between the distributor connector
and cavity A-17 at the PCM. If continuity is not
present, repair the harness as necessary.
(b) Check for continuity between the camshaft
position sensor output wire and cavity A-18 at the
PCM. If continuity is not present, repair the har-
ness as necessary.
(c) Check for continuity between the ground cir-
cuit wire at the distributor connector and ground.
If continuity is not present, repair the harness as
necessary.
(11) While observing the voltmeter, crank the
engine with ignition switch. The voltmeter needle
Fig. 14 Camshaft Position Sensor—Typical should fluctuate between 0 and 5 volts while the
To perform a complete test of this sensor and its engine is cranking. This verifies that the camshaft
circuitry, refer to the appropriate Powertrain Diag- position sensor in the distributor is operating prop-
nostics Procedures service manual. To test the sensor erly and a sync pulse signal is being generated.
only, refer to the following: If sync pulse signal is not present, replacement of
For this test, an analog (non-digital) voltme- the camshaft position sensor is necessary
ter is needed. Do not remove the distributor connec-
tor from the distributor. Using small paper clips, SPARK PLUG CABLES
insert them into the backside of the distributor wire Check the spark plug cable connections for good
harness connector to make contact with the termi- contact at the coil(s), distributor cap towers, and
nals. Be sure that the connector is not damaged spark plugs. Terminals should be fully seated. The
when inserting the paper clips. Attach voltmeter insulators should be in good condition and should fit
leads to these paper clips. tightly on the coil, distributor and spark plugs. Spark
(1) Connect the positive (+) voltmeter lead into the plug cables with insulators that are cracked or torn
sensor output wire. This is at done the distributor must be replaced.
wire harness connector. For wire identification, refer Clean high voltage ignition cables with a cloth
to Group 8W, Wiring Diagrams. moistened with a non-flammable solvent. Wipe the
(2) Connect the negative (-) voltmeter lead into the cables dry. Check for brittle or cracked insulation.
ground wire. For wire identification, refer to Group
8W, Wiring Diagrams. TESTING
(3) Set the voltmeter to the 15 Volt DC scale. When testing secondary cables for damage with an
(4) Remove distributor cap from distributor (two oscilloscope, follow the instructions of the equipment
screws). Rotate (crank) the engine until the distribu- manufacturer.
tor rotor is approximately in the 11 o’clock position. If an oscilloscope is not available, spark plug cables
The movable pulse ring should now be within the may be tested as follows:
sensor pickup.
(5) Turn ignition key to ON position. Voltmeter CAUTION: Do not leave any one spark plug cable
should read approximately 5.0 volts. disconnected for longer than necessary during test-
(6) If voltage is not present, check the voltmeter ing. This may cause possible heat damage to the
leads for a good connection. catalytic converter. Total test time must not exceed
ten minutes.
With the engine running, remove spark plug cable ifications as found in the Spark Plug Cable
from spark plug (one at a time) and hold next to a Resistance chart, replace the cable. Inspect the igni-
good engine ground. If the cable and spark plug are tion coil tower for cracks, burns or corrosion.
in good condition, the engine rpm should drop and
the engine will run poorly. If engine rpm does not SPARK PLUG CONDITIONS
drop, the cable and/or spark plug may not be operat-
ing properly and should be replaced. Also check NORMAL OPERATING
engine cylinder compression. The few deposits present on the spark plug will
With the engine not running, connect one end of a probably be light tan or slightly gray in color. This is
test probe to a good ground. Start the engine and run evident with most grades of commercial gasoline
the other end of the test probe along the entire (Fig. 15). There will not be evidence of electrode
length of all spark plug cables. If cables are cracked burning. Gap growth will not average more than
or punctured, there will be a noticeable spark jump approximately 0.025 mm (.001 in) per 3200 km (2000
from the damaged area to the test probe. The cable miles) of operation. Spark plugs that have normal
running from the ignition coil to the distributor cap wear can usually be cleaned, have the electrodes
can be checked in the same manner. Cracked, dam- filed, have the gap set and then be installed.
aged or faulty cables should be replaced with resis-
tance type cable. This can be identified by the words
ELECTRONIC SUPPRESSION printed on the cable
jacket.
Use an ohmmeter to test for open circuits, exces-
sive resistance or loose terminals. Remove the dis-
tributor cap from the distributor. Do not remove
cables from cap. Remove cable from spark plug.
Connect ohmmeter to spark plug terminal end of
cable and to corresponding electrode in distributor
cap. Resistance should be 250 to 1000 Ohms per inch
of cable. If not, remove cable from distributor cap
tower and connect ohmmeter to the terminal ends of
cable. If resistance is not within specifications as
found in the SPARK PLUG CABLE RESISTANCE
chart, replace the cable. Test all spark plug cables in
this manner.
Fig. 15 Normal Operation and Cold (Carbon) Fouling
SPARK PLUG CABLE RESISTANCE
Some fuel refiners in several areas of the United
States have introduced a manganese additive (MMT)
MINIMUM MAXIMUM for unleaded fuel. During combustion, fuel with MMT
250 Ohms Per Inch 1000 Ohms Per Inch causes the entire tip of the spark plug to be coated
3000 Ohms Per Foot 12,000 Ohms Per Foot with a rust colored deposit. This rust color can be
misdiagnosed as being caused by coolant in the com-
bustion chamber. Spark plug performance may be
affected by MMT deposits.
To test ignition coil-to-distributor cap cable, do not
remove the cable from the cap. Connect ohmmeter to COLD FOULING/CARBON FOULING
rotor button (center contact) of distributor cap and Cold fouling is sometimes referred to as carbon
terminal at ignition coil end of cable. If resistance is fouling. The deposits that cause cold fouling are basi-
not within specifications as found in the Spark Plug cally carbon (Fig. 15). A dry, black deposit on one or
Cable Resistance chart, remove the cable from the two plugs in a set may be caused by sticking valves
distributor cap. Connect the ohmmeter to the termi- or defective spark plug cables. Cold (carbon) fouling
nal ends of the cable. If resistance is not within spec- of the entire set of spark plugs may be caused by a
clogged air cleaner element or repeated short operat-
ing times (short trips).
WET FOULING OR GAS FOULING
A spark plug coated with excessive wet fuel or oil
is wet fouled. In older engines, worn piston rings,
leaking valve guide seals or excessive cylinder wear
can cause wet fouling. In new or recently overhauled
engines, wet fouling may occur before break-in (nor-
mal oil control) is achieved. This condition can usu-
ally be resolved by cleaning and reinstalling the
fouled plugs.
OIL OR ASH ENCRUSTED

If one or more spark plugs are oil or oil ash
encrusted (Fig. 16), evaluate engine condition for the
cause of oil entry into that particular combustion
chamber.
Fig. 17 Electrode Gap Bridging

SCAVENGER DEPOSITS
Fuel scavenger deposits may be either white or yel-
low (Fig. 18). They may appear to be harmful, but
this is a normal condition caused by chemical addi-
tives in certain fuels. These additives are designed to
change the chemical nature of deposits and decrease
spark plug misfire tendencies. Notice that accumula-
tion on the ground electrode and shell area may be
heavy, but the deposits are easily removed. Spark
plugs with scavenger deposits can be considered nor-
mal in condition and can be cleaned using standard
procedures.
Fig. 16 Oil or Ash Encrusted

ELECTRODE GAP BRIDGING
Electrode gap bridging may be traced to loose
deposits in the combustion chamber. These deposits
accumulate on the spark plugs during continuous
stop-and-go driving. When the engine is suddenly
subjected to a high torque load, deposits partially liq-
uefy and bridge the gap between electrodes (Fig. 17).
This short circuits the electrodes. Spark plugs with Fig. 18 Scavenger Deposits
electrode gap bridging can be cleaned using standard
procedures.
CHIPPED ELECTRODE INSULATOR
A chipped electrode insulator usually results from
bending the center electrode while adjusting the
spark plug electrode gap. Under certain conditions,
severe detonation can also separate the insulator
from the center electrode (Fig. 19). Spark plugs with
this condition must be replaced.
Fig. 20 Preignition Damage
Fig. 19 Chipped Electrode Insulator

PREIGNITION DAMAGE
Preignition damage is usually caused by excessive
combustion chamber temperature. The center elec-
trode dissolves first and the ground electrode dis-
solves somewhat latter (Fig. 20). Insulators appear
relatively deposit free. Determine if the spark plug
has the correct heat range rating for the engine.
Determine if ignition timing is over advanced or if
other operating conditions are causing engine over- Fig. 21 Spark Plug Overheating
heating. (The heat range rating refers to the operat-
ing temperature of a particular type spark plug. REMOVAL AND INSTALLATION
Spark plugs are designed to operate within specific
temperature ranges. This depends upon the thick- SPARK PLUG CABLE REMOVAL
ness and length of the center electrodes porcelain
insulator.) CAUTION: When disconnecting a high voltage
cable from a spark plug or from the distributor cap,
SPARK PLUG OVERHEATING twist the rubber boot slightly (1/2 turn) to break it
Overheating is indicated by a white or gray center loose (Fig. 22). Grasp the boot (not the cable) and
electrode insulator that also appears blistered (Fig. pull it off with a steady, even force.
21). The increase in electrode gap will be consider-
ably in excess of 0.001 inch per 2000 miles of opera-
tion. This suggests that a plug with a cooler heat SPARK PLUGS
range rating should be used. Over advanced ignition
timing, detonation and cooling system malfunctions PLUG REMOVAL
can also cause spark plug overheating. (1) Always remove spark plug or ignition coil
cables by grasping at the cable boot (Fig. 22). Turn
the cable boot 1/2 turn and pull straight back in a
steady motion. Never pull directly on the cable.
Internal damage to cable will result.
Fig. 22 Cable Removal

(2) Prior to removing the spark plug, spray com-
pressed air around the spark plug hole and the area
around the spark plug. This will help prevent foreign
material from entering the combustion chamber.
(3) Remove the spark plug using a quality socket Fig. 23 Setting Spark Plug Gap—Typical
with a rubber or foam insert.
(4) Inspect the spark plug condition. Refer to When replacing the spark plug and ignition coil
Spark Plugs in the Diagnostics/Service Procedures cables, route the cables correctly and secure them in
section of this group. the appropriate retainers. Failure to route the cables
properly can cause the radio to reproduce ignition
PLUG CLEANING noise. It could cause cross ignition of the spark plugs,
The plugs may be cleaned using commercially or short circuit the cables to ground.
available spark plug cleaning equipment. After clean- (1) Start the spark plug into the cylinder head by
ing, file the center electrode flat with a small point hand to avoid cross threading.
file or jewelers file before adjusting gap. (2) Tighten the spark plugs to 35-41 N·m (26-30 ft.
lbs.) torque.
CAUTION: Never use a motorized wire wheel brush (3) Install spark plug cables over spark plugs.
to clean the spark plugs. Metallic deposits will
remain on the spark plug insulator and will cause IGNITION COIL
plug misfire. The ignition coil is an epoxy filled type. If the coil
is replaced, it must be replaced with the same type.
PLUG GAP ADJUSTMENT REMOVAL

Check the spark plug gap with a gap gauge tool. If On the 2.5L 4-cylinder engine, the ignition coil is
the gap is not correct, adjust it by bending the mounted to a bracket on side of engine (to rear of
ground electrode (Fig. 23). Never attempt to adjust distributor) (Fig. 24).
the gap by bending the center electrode. On the 4.0L 6-cylinder engine, the ignition coil is
mounted to a bracket on side of engine (to front of
SPARK PLUG GAP distributor) (Fig. 25).
• 2.5L 4-Cylinder Engine Spark Plug Gap: .89 mm (1) Disconnect ignition coil secondary cable from
(.035 in). ignition coil.
• 4.0L 6-Cylinder Engine Spark Plug Gap: .89 mm (2) Disconnect engine harness connector from igni-
(.035 in). tion coil.
(3) Remove ignition coil mounting bolts (nuts are
PLUG INSTALLATION used on back side of bracket on some coils).
Always tighten spark plugs to the specified torque. (4) Remove coil from vehicle.
Over tightening can cause distortion. This may result
in a change in the spark plug gap, or a cracked por-
celain insulator.
On 2.5L 4-cylinder and 4.0L 6-cylinder engines
with manual transmissions, the sensor is attached
with two bolts. On 2.5L engines with automatic
transmissions, the sensor is attached with two nuts.
On 4.0L engines with automatic transmissions, the
sensor is adjustable and is attached with one bolt.
Fig. 26 Crankshaft Position Sensor—4.0L 6-Cyl.

Engine—Auto. Trans.
REMOVAL

INSTALLATION
(1) Install ignition coil to bracket on cylinder block
with mounting bolts (and nuts if equipped). If
equipped with nuts and bolts, tighten to 11 N·m (100
in. lbs.) torque. If equipped with bolts only, tighten to
5 N·m (50 in. lbs.) torque.
(2) Connect engine harness connector to coil.
(3) Connect ignition coil cable to ignition coil.
CRANKSHAFT POSITION SENSOR

The crankshaft position sensor is mounted to the Fig. 27 Crankshaft Position Sensor—2.5L 4-Cyl.
transmission bellhousing at the left/rear side of the Engine—Auto. Trans.
engine block (Fig. 26), (Fig. 27), or (Fig. 28).
(5) Used Sensors: Clean bottom of sensor and
install spacer PN05252229.
(6) Install sensor into transmission bellhousing
hole.
(7) Push sensor against flywheel/drive plate. With
sensor pushed against flywheel/drive plate, tighten
mounting bolt to 7 N·m (60 in. lbs.) torque.
(8) Connect sensor pigtail harness electrical con-
nector to main wiring harness.
CAMSHAFT POSITION SENSOR

The camshaft position sensor is located in the dis-
tributor (Fig. 29).
REMOVAL
Distributor removal is not necessary to remove
camshaft position sensor.
(1) Disconnect negative battery cable at battery.
(2) Remove distributor cap from distributor (two
screws).
(3) Disconnect camshaft position sensor wiring
harness from main engine wiring harness.
Fig. 28 Crankshaft Position Sensor—Manual
Transmission (Typical)
(1) Near rear of intake manifold, disconnect pigtail
harness (electrical connector) from main electrical
harness.
(2) Depending upon application, remove either sen-
sor mounting bolt(s) or nuts.
(3) Remove sensor from engine.
INSTALLATION
2.5L and 4.0L engines with manual transmis-
sion:
(1) Install sensor flush against opening in trans-
mission housing.
(2) Install and tighten two sensor mounting bolts
to 19 N·m (14 ft. lbs.) torque. The two sensor mount-
ing bolts are specially machined to correctly space Fig. 29 Camshaft Position Sensor
unit to flywheel. Do not attempt to install any other
(4) Remove distributor rotor from distributor shaft.
bolts.
(5) Lift camshaft position sensor assembly from
2.5L engines with automatic transmission:
distributor housing (Fig. 29).
(3) Install and tighten two sensor mounting nuts
to 19 N·m (14 ft. lbs.) torque. INSTALLATION
4.0L engines with automatic transmission:
(1) Install camshaft position sensor to distributor.
New replacement sensors will be equipped with a
Align sensor into notch on distributor housing.
paper spacer glued to bottom of sensor. If installing
(2) Connect wiring harness.
(returning) a used sensor to vehicle, a new paper
(3) Install rotor.
spacer must be installed to bottom of sensor. This
(4) Install distributor cap. Tighten mounting
spacer will be ground off the first time engine is
screws.
started. If spacer is not used, sensor will be broken
the first time engine is started.
(4) New Sensors: Be sure paper spacer is installed
DISTRIBUTOR
All distributors contain an internal oil seal that
to bottom of sensor. If not, obtain spacer
prevents oil from entering the distributor housing.
PN05252229.
The seal is not serviceable.
Factory replacement distributors are equipped with
a plastic alignment pin already installed. The pin is
located in an access hole on the bottom of the distrib-
utor housing (Fig. 30). It is used to temporarily lock
the rotor to the cylinder number 1 position during
installation. The pin must be removed after install-
ing the distributor.
Fig. 31 Distributor—2.5L Or 4.0L Engines—Typical

Fig. 30 Plastic Alignment Pin (4) Disconnect distributor wiring harness from
The camshaft position sensor is located in the dis- main engine harness.
tributor on all engines (Fig. 31). For removal/instal- (5) Remove cylinder number 1 spark plug.
lation procedures, refer to Camshaft Position Sensor. (6) Hold a finger over open spark plug hole. Rotate
Distributor removal is not necessary for sensor engine at vibration dampener bolt until compression
removal. (pressure) is felt.
Refer to (Fig. 31) for an exploded view of the dis- (7) Slowly continue to rotate engine. Do this until
tributor. timing index mark on vibration damper pulley aligns
A fork with a slot is supplied on the bottom of the with top dead center (TDC) mark (0 degree) on tim-
distributor housing where the housing base seats ing degree scale (Fig. 32). Always rotate engine in
against the engine block (Fig. 31). The centerline of direction of normal rotation. Do not rotate engine
the slot aligns with the distributor holddown bolt backward to align timing marks.
hole in the engine block. Because of the fork, the dis- (8) On models equipped with A/C, remove electri-
tributor cannot be rotated. Distributor rotation is not cal cooling fan and shroud assembly from radiator.
necessary as all ignition timing requirements are Refer to Group 7, Cooling System for procedures.
handled by the powertrain control module (PCM). (9) This will provide room to turn engine crank-
The position of the distributor determines fuel syn- shaft with a socket and ratchet using vibration
chronization only. It does not determine ignition tim- damper bolt.
ing. (10) Remove distributor holddown bolt and clamp.
(11) Remove distributor from engine by slowly lift-
NOTE: Do not attempt to modify this fork to attain ing straight up.
ignition timing. (12) Note that rotor will rotate slightly in a coun-
terclockwise direction while lifting up distributor.
The oil pump gear will also rotate slightly in a coun-
REMOVAL—2.5L OR 4.0L ENGINE terclockwise direction while lifting up distributor.
(1) Disconnect negative battery cable at battery. This is due to the helical cut gears on distributor and
(2) Disconnect coil secondary cable at coil. camshaft.
(3) Remove distributor cap from distributor (2 (13) Note removed position of rotor during distrib-
screws). Do not remove cables from cap. Do not utor removal. During installation, this will be
remove rotor. referred to as the Pre-position.
Fig. 34 Slot At 11 O’clock Position—4.0L Engine

(16) Remove and discard the old distributor-to-en-
gine block gasket.
INSTALLATION
Fig. 32 Align Timing Marks (1) If engine crankshaft has been rotated after dis-
tributor removal, cylinder number 1 must be
(14) 2.5L 4-Cylinder Engine: Observe slot in oil returned to its proper firing stroke. Refer to previous
pump gear through hole on side of engine. It should REMOVAL Step 5 and Step 6. These steps must be
be slightly before (counterclockwise of) 10 o’clock done before installing distributor.
position (Fig. 33). (2) Check position of slot on oil pump gear. On the
(15) 4.0L 6-Cylinder Engine: Observe slot in oil 2.5L engine, it should be just slightly before (counter-
pump gear through hole on side of engine. It should clockwise of) 10 o’clock position (Fig. 33). On the 4.0L
be slightly before (counterclockwise of) 11 o’clock engine, it should be just slightly before (counterclock-
position (Fig. 34). wise of) 11 o’clock position (Fig. 34). If not, place a
flat blade screwdriver into oil pump gear and rotate
it into proper position.
(3) Factory replacement distributors are equipped
with a plastic alignment pin already installed (Fig.
30). This pin is used to temporarily hold rotor to cyl-
inder number 1 firing position during distributor
installation. If pin is in place, proceed to Step 8. If
not, proceed to next step.
(4) If original distributor is to be reinstalled, such
as during engine overhaul, the plastic pin will not be
available. A 3/16 inch drift pin punch tool may be
substituted for plastic pin.
(5) Remove camshaft position sensor from distrib-
utor housing. Lift straight up.
(6) Four different alignment holes are provided on
plastic ring (Fig. 35). Note that 2.5L and 4.0L
Fig. 33 Slot At 10 O’clock Position—2.5L Engine engines have different alignment holes (Fig.
35).
(7) Rotate distributor shaft and install pin punch slot in oil pump gear. The same may have to be done
tool through proper alignment hole in plastic ring to engage distributor gear with camshaft gear.
(Fig. 35) and into mating access hole in distributor
housing. This will prevent distributor shaft and rotor
from rotating.
Fig. 36 Distributor Pre-position—All Engines
Fig. 35 Pin Alignment Holes

(8) Clean distributor mounting hole area of engine
block.
(9) Install new distributor-to-engine block gasket
(Fig. 31).
(10) Install rotor to distributor shaft.
(11) 2.5L 4-Cylinder Engine: Pre-position distrib-
utor into engine while holding centerline of base slot
in 1 o’clock position (Fig. 36). Continue to engage dis-
tributor into engine. The rotor and distributor will
rotate clockwise during installation. This is due to
the helical cut gears on distributor and camshaft.
When distributor is fully seated to engine block, the
centerline of base slot should be aligned to clamp bolt
mounting hole on engine (Fig. 37). The rotor should
also be pointed slightly past (clockwise of) 3 o’clock
position.
4.0L 6-Cylinder Engine: Pre-position distributor
into engine while holding centerline of base slot in 1
o’clock position (Fig. 36). Continue to engage distrib-
utor into engine. The rotor and distributor will rotate Fig. 37 Distributor Engaged Position—2.5L
clockwise during installation. This is due to the heli- 4-Cylinder Engine
cal cut gears on distributor and camshaft. When dis- The distributor is correctly installed when:
tributor is fully seated to engine block, the centerline • rotor is pointed at 3 o’clock position (2.5L
of base slot should be aligned to clamp bolt mounting engine), or at 5 o’clock position (4.0L engine).
hole on engine (Fig. 38). The rotor should also be • plastic alignment pin (or pin punch tool) is still
pointed at 5 o’clock position. installed to distributor.
It may be necessary to rotate rotor and distributor
shaft (very slightly) to engage distributor shaft with
IGNITION SWITCH AND KEY CYLINDER

The ignition key must be in the key cylinder for
cylinder removal. The key cylinder must be removed
first before removing ignition switch.
KEY CYLINDER REMOVAL

(2) If equipped with an automatic transmission,
place shifter in PARK position.
(3) Rotate key to ON position.
(4) A release tang is located on bottom of key cyl-
inder (Fig. 39).
Fig. 38 Distributor Engaged Position—4.0L

6-Cylinder Engine
• number 1 cylinder piston is set at top dead cen-
ter (TDC) (compression stroke).
• centerline of slot at base of distributor is aligned
to centerline of distributor holddown bolt hole on
engine. In this position, the holddown bolt should Fig. 39 Key Cylinder Release Tang
easily pass through slot and into engine.
No adjustments are necessary. Proceed to next
step.
(12) Install distributor holddown clamp and bolt.
Tighten bolt to 23 N·m (17 ft. lbs.) torque.
(13) Remove pin punch tool from distributor. Or, if
plastic alignment pin was used, remove it straight
down from bottom of distributor. Discard plastic pin.
(14) If removed, install camshaft position sensor to
distributor. Align wiring harness grommet to notch in
distributor housing.
(15) Install rotor.
CAUTION: If the distributor cap is incorrectly posi-

tioned on distributor housing, cap or rotor may be
damaged when engine is started.
(16) Install distributor cap. Tighten distributor cap

holddown screws to 3 N·m (26 in. lbs.) torque.
(17) If removed, install spark plug cables to dis-
tributor cap. For proper firing order, refer to Specifi-
cations section at the end of this group. See Engine
Firing Order.
(18) Connect distributor wiring harness to main Fig. 40 Key Cylinder and Cover Removal
engine harness.
(5) Position a small screwdriver or pin punch into
(19) Connect battery cable to battery.
tang access hole on bottom of steering column lower
cover (Fig. 40).
(6) Push the pin punch up while pulling key cylin-
der from steering column.
IGNITION SWITCH REMOVAL

(1) Remove key cylinder. Refer to previous steps.
(2) Remove lower steering column cover screws
and remove cover (Fig. 40).
Fig. 43 Ignition Switch Removal/Installation

IGNITION SWITCH INSTALLATION
(1) Before installing ignition switch, rotate the slot
in the switch to the ON position (Fig. 42).
(2) Connect two electrical connectors to rear of
ignition switch. Make sure that locking tabs are fully
seated into wiring connectors.
Fig. 41 Ignition Switch Lock Tab (3) Position switch to column and install tamper
proof screw. Tighten screw to 3 N·m (26 in. lbs.).
(4) Install steering column lower cover.
KEY CYLINDER INSTALLATION

(1) If equipped with an automatic transmission,
place shifter in PARK position.
(2) Position key cylinder into steering column as it
would normally be in the ON position.
(3) Press key cylinder into column until it snaps
into position.
(4) Check mechanical operation of switch. Auto-
matic Transmission: Be sure transmission lever is
locked in PARK position after key removal. If key is
difficult to rotate or is difficult to remove, the shift
lever-to-steering column cable may be out of adjust-
ment or defective. Refer to Group 21, Transmission
Fig. 42 Switch In ON Position for procedures. Manual Transmission: Be sure key
cannot be removed until release lever is operated. If
(3) Remove ignition switch mounting screw (Fig. key can be removed, release lever mechanism may be
43). Use tamper proof torx bit (Snap-Ont SDMTR10 defective. Release lever mechanism is not serviced
or equivalent) to remove the screw. separately. If repair is necessary, the steering column
(4) Using a small screwdriver, push on locking tab must be replaced. Refer to Group 19, Steering for
(Fig. 41) and remove switch from steering column. procedures.
(5) Disconnect two electrical connectors at rear of (5) Connect negative cable to battery.
ignition switch (Fig. 43). (6) Check electrical operation of switch.
SHIFTER/IGNITION INTERLOCK ENGINE FIRING ORDER—2.5L 4-CYLINDER

On models equipped with an automatic transmis- ENGINE
sion, a cable connects the ignition switch with the
floor shift lever. The shifter will be locked in the
PARK position when the ignition key is in the LOCK
or ACCESSORY positions. The cable can be adjusted
or replaced. Refer to Group 21, Transmissions for
procedures. The ignition interlock device within the
steering column is not serviceable. If service is nec-
essary, the steering column must be replaced. Refer
to Group 19, Steering for procedures.
SPECIFICATIONS
IGNITION TIMING
Ignition timing is not adjustable on any engine.
Refer to Ignition Timing in the Diagnostics/Service
Procedures section of this group for more informa-
tion.
ENGINE FIRING ORDER—4.0L 6-CYLINDER
ENGINE
SPECIFICATIONS (Continued)
SPARK PLUGS SPARK PLUG CABLE RESISTANCE
ENGINE PLUG TYPE ELECTRODE GAP MINIMUM MAXIMUM

2.5L/4.0L RC12ECC 0.89 mm (0.035 in.) 250 Ohms Per Inch 1000 Ohms Per Inch
3000 Ohms Per Foot 12,000 Ohms Per Foot
IGNITION COIL RESISTANCE
PRIMARY RESISTANCE SECONDARY RESISTANCE

COIL MANUFACTURER
21-27°C (70-80°F) 21-27°C (70-80°F)
Diamond 0.97 - 1.18 Ohms 11,300 - 15,300 Ohms
Toyodenso 0.95 - 1.20 Ohms 11,300 - 13,300 Ohms
TORQUE CHART
DESCRIPTION TORQUE
Crankshaft Position Sensor Bolts—With
Manual Transmission . . . . . . . 19 N·m(14 ft. lbs.)
Crankshaft Position Sensor Nuts—2.5L With
Automatic Transmission . . . . . 19 N·m (14 ft. lbs.)
Crankshaft Position Sensor Bolt—4.0L With
Automatic Transmission . . . . . 7 N·m (60 in. lbs.)
Distributor Hold Down Bolt . . . . 23 N·m (17 ft. lbs.)
Distributor Cap Screws . . . . . . . . 3 N·m (26 in. lbs.)
Ignition Coil Mounting
(if tapped bolts are used) . . . . . 5 N·m (50 in. lbs.)
Ignition Coil Mounting
(if nuts/bolts are used) . . . . . 11 N·m (100 in. lbs.)
Spark Plugs (all engines) . . . . . . 41 N·m (30 ft. lbs.)
TJ INSTRUMENT PANEL SYSTEMS 8E - 1
INSTRUMENT PANEL SYSTEMS

CONTENTS
page page
DESCRIPTION AND OPERATION GLOVE BOX COMPONENTS . . . . . . . . . . . . . . . 19

ACCESSORY RELAY . . . . . . . . . . . . . . . . . . . . . . 4 GLOVE BOX LATCH STRIKER . . . . . . . . . . . . . 21
INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . . . . 2 HEADLAMP SWITCH . . . . . . . . . . . . . . . . . . . . 11
INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . 1 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . . . 13
INSTRUMENT PANEL CIGAR LIGHTER AND INSTRUMENT CLUSTER COMPONENTS . . . . . 14
POWER OUTLET . . . . . . . . . . . . . . . . . . . . . . . 3 INSTRUMENT PANEL ACCESSORY SWITCH
INSTRUMENT PANEL SYSTEM . . . . . . . . . . . . . 1 BEZEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DIAGNOSIS AND TESTING INSTRUMENT PANEL ASSEMBLY . . . . . . . . . . 22
ACCESSORY RELAY . . . . . . . . . . . . . . . . . . . . . . 9 INSTRUMENT PANEL BASE TRIM . . . . . . . . . . 24
INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . . . . 4 INSTRUMENT PANEL CENTER BEZEL . . . . . . . 17
INSTRUMENT PANEL CIGAR LIGHTER AND INSTRUMENT PANEL GRAB HANDLE . . . . . . . 21
POWER OUTLET . . . . . . . . . . . . . . . . . . . . . . 10 INSTRUMENT PANEL GRAB HANDLE BEZEL . 22
REMOVAL AND INSTALLATION INSTRUMENT PANEL TOP COVER . . . . . . . . . . 12
ACCESSORY RELAY . . . . . . . . . . . . . . . . . . . . . 18 KNEE BLOCKER . . . . . . . . . . . . . . . . . . . . . . . . 11
CLUSTER BEZEL . . . . . . . . . . . . . . . . . . . . . . . . 13 STEERING COLUMN OPENING COVER . . . . . . 10
GLOVE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DESCRIPTION AND OPERATION mounted on or in the instrument panel. If you cannot

locate a listing for the component or system you are
INSTRUMENT PANEL SYSTEM servicing in the table of contents for this group, or if
you are uncertain as to which vehicle system a com-
DESCRIPTION ponent belongs to, it is suggested that you refer to
The instrument panel serves as the command cen- the alphabetical Component and System Index
ter of the vehicle, which necessarily makes it a very found at the back of this service manual.
complex unit. The instrument panel is designed to
house the controls and monitors for standard and INSTRUMENT PANEL
optional powertrains, climate control systems, audio
systems, lighting systems, safety systems and many DESCRIPTION
other comfort or convenience items. The instrument Modular instrument panel construction allows all
panel is also designed so that all of the various con- of the gauges and controls to be serviced from the
trols can be safely reached and the monitors can be front of the panel. In addition, most of the instru-
easily viewed by the vehicle operator when driving, ment panel electrical or heating and air conditioning
while still allowing relative ease of access to each of components can be accessed without complete instru-
these items for service. See the owner’s manual in ment panel removal. If necessary, the instrument
the vehicle glove box for more information on the fea- panel can be removed from the vehicle as an assem-
tures, use and operation of all of the instrument bly.
panel components and systems. Removal of the steering column opening cover and
This group is responsible for covering service infor- the knee blocker provides access to the steering col-
mation for the vehicle instrument panel systems. umn mounts, the steering column wiring, the gear-
However, complete service information coverage for shift interlock mechanism, the headlamp switch, and
all of the systems and components housed in the much of the instrument panel wiring. Removal of the
instrument panel in a single section of the service glove box provides access to the fuseblock module,
manual would not be practical. Therefore, the service additional instrument panel wiring, and many of the
information for any component will be found in the heating and air conditioning components.
group designated to cover the vehicle system that the Removal of the instrument cluster bezel allows
component belongs to, even though the component is access to the cluster assembly. Removal of the cluster
8E - 2 INSTRUMENT PANEL SYSTEMS TJ
assembly allows access to the cluster illumination tioning the gauge needles at several predetermined
and indicator lamp bulbs, and more of the instru- locations on the gauge faces in a prescribed sequence.
ment panel wiring. For more information on this function, refer to
Removal of the instrument panel center bezel Instrument Cluster in the Diagnosis and Testing
allows access to the radio, the heating and air condi- section of this group.
tioning controls, the power outlet or cigar lighter, and The instrument cluster circuitry also integrates a
the accessory switches. The power outlet/cigar lighter chime tone generator and a timer circuit. These
is serviced only as a unit with the accessory switch items replace the chime or buzzer module, and the
bezel. separate timer circuit for the rear window defogger
A bezel on each outboard end of the lower instru- system. Refer to Chime Warning System in the
ment panel is removed to service the instrument Description and Operation section of Group 8U -
panel speakers. Removal of the complete instrument Chime/Buzzer Warning Systems for more information
panel is required for service of the passenger side on the chime functions of the instrument cluster.
airbag module and most internal components of the Refer to Rear Window Defogger System in the
heating and air conditioning system housing. Description and Operation section of Group 8N -
Electrically Heated Systems for more information on
INSTRUMENT CLUSTER the timer function of the instrument cluster.
The instrument cluster for this model is serviced
DESCRIPTION only as a complete unit. If a cluster gauge or the
A single instrument cluster is offered on this cluster circuit board are faulty, the entire cluster
model. This cluster is an electromechanical unit that must be replaced. The cluster lens, the cluster hood
utilizes integrated circuitry and information carried and mask, the rear cluster housing cover, the odom-
on the Chrysler Collision Detection (CCD) data bus eter reset knob boot and the incandescent lamp bulbs
network for control of all gauges and many of the and holders are available for service replacement.
indicator lamps. This cluster also incorporates a dig-
ital Vacuum Fluorescent Display (VFD) for the odom- OPERATION
eter/trip odometer display functions. Some variations
of this cluster exist due to optional equipment and GAUGE
regulatory requirements. With the ignition switch in the On or Start posi-
The cluster includes the following analog gauges: tions, voltage is supplied to all gauges through the
• Coolant temperature gauge instrument cluster electronic circuit board. With the
• Fuel gauge ignition switch in the Off position, voltage is not sup-
• Oil pressure gauge plied to the gauges. The gauges do not accurately
• Speedometer indicate any vehicle condition unless the ignition
• Tachometer switch is in the On or Start positions.
• Voltmeter. All of the instrument cluster gauges, except the
This cluster also includes provisions for the follow- odometer, are air core magnetic units. Two fixed elec-
ing indicator lamps: tromagnetic coils are located within the gauge. These
• Airbag indicator lamp coils are wrapped at right angles to each other
• Anti-lock Brake System (ABS) lamp around a movable permanent magnet. The movable
• Brake warning lamp magnet is suspended within the coils on one end of a
• Check gauges lamp shaft. The gauge needle is attached to the other end
• Cruise-on indicator lamp of the shaft.
• Four-wheel drive indicator lamp One of the coils has a fixed current flowing
• Headlamp high beam indicator lamp through it to maintain a constant magnetic field
• Low fuel warning lamp strength. Current flow through the second coil
• Malfunction indicator (Check Engine) lamp changes, which causes changes in its magnetic field
• Seat belt reminder lamp strength. The current flowing through the second coil
• Sentry Key Immobilizer System (SKIS) indicator is changed by the instrument cluster electronic cir-
lamp cuitry in response to messages received on the
• Turn signal indicator lamps Chrysler Collision Detection (CCD) data bus network.
• Upshift indicator lamp (manual transmission). The gauge needle moves as the movable permanent
The instrument cluster circuitry has a self-diagnos- magnet aligns itself to the changing magnetic fields
tic actuator test capability, which will test each of the created around it by the electromagnets. The instru-
CCD bus message-controlled functions of the cluster ment cluster circuitry is programmed to move all of
by lighting the appropriate indicator lamps and posi- the gauge needles back to the low end of their respec-
tive scales after the ignition switch is turned to the instrument panel accessory switch bezel, which is
Off position. located near the bottom of the instrument panel cen-
ter bezel area, next to the ash receiver. A plastic cap
INDICATOR LAMP snaps into the power outlet base when the power out-
Indicator lamps are located in the instrument clus- let is not in use. A cigar lighter that fits into the
ter and are served by the cluster circuit board and power outlet is a dealer-installed option.
connectors. Many of the indicator lamps in the The cigar lighter/power outlet base is serviced only
instrument cluster are controlled by the instrument as a part of the accessory switch bezel unit. If the
cluster circuitry in response to messages received base is faulty or damaged, the accessory switch bezel
over the Chrysler Collision Detection (CCD) data bus unit must be replaced. The cigar lighter knob and
network. heating element unit is available for service. This
The anti-lock brake system lamp, brake warning component cannot be repaired and, if faulty or dam-
lamp, four-wheel drive indicator lamp, headlamp aged, it must be replaced.
high beam indicator lamp, and turn signal indicator
lamps are hard wired. The seat belt reminder lamp is OPERATION
controlled by the instrument cluster programming. The cigar lighter/power outlet base or receptacle
The instrument cluster circuitry uses CCD data bus shell is connected to ground, and an insulated con-
messages from the Powertrain Control Module tact in the bottom of the shell is connected to battery
(PCM), Airbag Control Module (ACM), and the Sen- current. The power outlet receives battery voltage
try Key Immobilizer Module (SKIM) to control all of from a fuse in the Power Distribution Center (PDC)
the remaining indicator lamps. through the accessory relay only when the ignition
Each of the indicator lamps in the instrument clus- switch is in the Accessory or On positions. Refer to
ter uses incandescent bulbs and holders, which are Accessory Relay in the Description and Operation
available for service replacement. section of this group for more information on this
component.
CLUSTER ILLUMINATION LAMP The cigar lighter knob and heating element are
The cluster illumination lamps are hard wired in encased within a spring-loaded housing, which also
the instrument cluster. When the park or head lamps features a sliding protective heat shield. When the
are turned on, the cluster illumination lamps light. knob and heating element are inserted in the recep-
Illumination brightness is adjusted by rotating the tacle shell, the heating element resistor coil is
headlamp switch knob (clockwise to dim, counter- grounded through its housing to the receptacle shell.
clockwise to brighten). The instrument cluster illumi- If the cigar lighter knob is pushed inward, the heat
nation lamps receive battery feed from the panel shield slides up toward the knob exposing the heat-
dimmer rheostat in the headlamp switch through a ing element, and the heating element extends from
fuse in the fuseblock module. the housing toward the insulated contact in the bot-
The instrument cluster electronic circuitry also tom of the receptacle shell.
monitors the cluster illumination lamp dimming level Two small spring-clip retainers are located on
whenever the park or head lamps are turned on. The either side of the insulated contact inside the bottom
instrument cluster electronic circuitry responds by of the receptacle shell. These clips engage and hold
adjusting the dimming level of the odometer Vacuum the heating element of the dealer-installed cigar
Fluorescent Display (VFD), and sending dimming lighter against the insulated contact long enough for
level messages over the Chrysler Collision Detection the resistor coil to heat up. When the heating ele-
(CCD) data bus network. When the park lamps or ment is engaged with the contact, battery current
headlamps are turned off, the VFD is illuminated at can flow through the resistor coil to ground, causing
full brightness for improved daylight visibility. the resistor coil to heat.
Each of the cluster illumination lamps is located on When the resistor coil becomes sufficiently heated,
the instrument cluster circuit board. Each cluster excess heat radiates from the heating element caus-
illumination lamp has a replaceable bulb and bulb ing the spring-clips to expand. Once the spring-clips
holder. expand far enough to release the heating element,
the spring-loaded housing forces the knob and heat-
INSTRUMENT PANEL CIGAR LIGHTER AND ing element to pop back outward to their relaxed
POWER OUTLET position. When the cigar lighter knob and element
are pulled out of the receptacle shell, the protective
DESCRIPTION heat shield slides downward on the housing so that
An accessory power outlet is standard equipment the heating element is recessed and shielded around
on this model. The power outlet is installed in the its circumference for safety.
ACCESSORY RELAY RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY

STEERING WHEEL, STEERING COLUMN, OR
DESCRIPTION INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
The accessory relay is an electromechanical device SERVICE. FAILURE TO TAKE THE PROPER PRE-
that switches fused battery current to the standard CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
accessory power outlet or optional cigar lighter when BAG DEPLOYMENT AND POSSIBLE PERSONAL
the ignition switch is turned to the Accessory or On INJURY.
positions. The accessory relay is located in a wire
harness connector that is secured to the 100-way con-
nector bracket under the driver side of the instru-
PRELIMINARY DIAGNOSIS
(1) If the indicator lamps operate, but none of the
ment panel, near the cowl side inner panel in the
gauges operate, go to Step 2. If all of the gauges and
passenger compartment.
the CCD data bus message-controlled indicator lamps
The accessory relay is a International Standards
are inoperative, go to Step 5.
Organization (ISO) relay. Relays conforming to the
(2) Check the fused B(+) fuse in the Power Distri-
ISO specifications have common physical dimensions,
bution Center (PDC). If OK, go to Step 3. If not OK,
current capacities, terminal patterns, and terminal
repair the shorted circuit or component as required
functions.
and replace the faulty fuse.
The accessory relay cannot be repaired or adjusted
(3) Check for battery voltage at the fused B(+) fuse
and, if faulty or damaged, it must be replaced.
in the PDC. If OK, go to Step 4. If not OK, repair the
OPERATION open fused B(+) circuit to the battery as required.
The ISO relay consists of an electromagnetic coil, a (4) Disconnect and isolate the battery negative
resistor or diode, and three (two fixed and one mov- cable. Remove the instrument cluster. Connect the
able) electrical contacts. The movable (common feed) battery negative cable. Check for battery voltage at
relay contact is held against one of the fixed contacts the fused B(+) circuit cavity of the instrument cluster
(normally closed) by spring pressure. When the elec- wire harness connector A. If OK, refer to Instru-
tromagnetic coil is energized, it draws the movable ment Cluster - Actuator Test in the Diagnosis and
contact away from the normally closed fixed contact, Testing section of this group. If not OK, repair the
and holds it against the other (normally open) fixed open fused B(+) circuit to the fuse in the PDC as
contact. required.
When the electromagnetic coil is de-energized, (5) Check the fused ignition switch output (run/
spring pressure returns the movable contact to the start) fuse in the fuseblock module. If OK, go to Step
normally closed position. The resistor or diode is con- 6. If not OK, repair the shorted circuit or component
nected in parallel with the electromagnetic coil in the as required and replace the faulty fuse.
relay, and helps to dissipate voltage spikes that are (6) Turn the ignition switch to the On position and
produced when the coil is de-energized. check for battery voltage at the fused ignition switch
output (run/start) fuse in the fuseblock module. If
OK, go to Step 7. If not OK, repair the open fused
DIAGNOSIS AND TESTING ignition switch output (run/start) circuit to the igni-
tion switch as required.
INSTRUMENT CLUSTER (7) Turn the ignition switch to the Off position.
If all of the gauges and/or indicator lamps are inop- Disconnect and isolate the battery negative cable.
erative, perform the Preliminary Diagnosis. If an Install the instrument cluster. Connect the battery
individual gauge or Chrysler Collision Detection negative cable. Turn the ignition switch to the On
(CCD) data bus message-controlled indicator lamp is position. Set the park brake. The red brake warning
inoperative, go directly to the Actuator Test. If an lamp should light. If OK, go to Step 8. If not OK, go
individual hard wired indicator lamp is inoperative, to Step 9.
refer to Instrument Cluster - Hard Wired Lamp (8) Turn the ignition switch to the Off position.
Diagnosis in the Diagnosis and Testing section of Turn on the park lamps and adjust the panel lamps
this group for the procedures to diagnosis that lamp. dimmer rheostat in the headlamp switch to the full
For complete circuit diagrams, refer to Instrument bright position. The cluster illumination lamps
Cluster in the Contents of Group 8W - Wiring Dia- should light. If OK, refer to Instrument Cluster -
grams. Actuator Test in the Diagnosis and Testing section
of this group. If not OK, go to Step 10.
WARNING: ON VEHICLES EQUIPPED WITH AIR- (9) Turn the ignition switch to the Off position.
BAGS, REFER TO GROUP 8M - PASSIVE Disconnect and isolate the battery negative cable.
Remove the instrument cluster. Connect the battery
negative cable. Turn the ignition switch to the On (1) Begin the test with the ignition switch in the
position. Check for battery voltage at the fused igni- Off position.
tion switch output (run/start) circuit cavity of the (2) Depress the trip odometer reset button.
instrument cluster wire harness connector A. If OK, (3) While holding the trip odometer reset button
refer to Instrument Cluster - Actuator Test in the depressed, turn the ignition switch to the On posi-
Diagnosis and Testing section of this group. If not tion, but do not start the engine.
OK, repair the open fused ignition switch output (4) Release the trip odometer reset button.
(run/start) circuit to the fuse in the fuseblock module (5) Compare the operation of the suspect gauge(s)
as required. and/or indicator lamp(s) with the Instrument Cluster
(10) Disconnect and isolate the battery negative Actuator Test chart (Fig. 1).
cable. Remove the instrument cluster. Check for con- (6) The instrument cluster will automatically exit
tinuity between the ground circuit cavity of the the self-diagnostic mode and return to normal opera-
instrument cluster wire harness connector A and a tion at the completion of the test, if the ignition
good ground. There should be continuity. If OK, refer switch is turned to the Off position during the test,
to Instrument Cluster - Actuator Test in the or if a vehicle speed message indicating that the
Diagnosis and Testing section of this group. If not vehicle is moving is received from the PCM on the
OK, repair the open ground circuit to ground as CCD data bus during the test.
required. (7) Go back to Step 1 to repeat the test, if
required.
ACTUATOR TEST
The instrument cluster actuator test will put the HARD WIRED LAMP DIAGNOSIS
instrument cluster into its self-diagnostic mode. In Each of the lamps found in this section depends
this mode the instrument cluster can perform a self- upon a hard wired circuit input to the instrument
diagnostic test that will confirm that the instrument cluster for proper operation. The following procedures
cluster circuitry, the gauges, and the CCD data bus will help to diagnose conditions that may cause an
message controlled indicator lamps are capable of inoperative hard wired lamp circuit condition.
operating as designed. During the actuator test the
instrument cluster circuitry will position each of the WARNING: ON VEHICLES EQUIPPED WITH AIR-
gauge needles at various specified calibration points, BAGS, REFER TO GROUP 8M - PASSIVE
and turn all of the CCD data bus message-controlled RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
lamps on and off at specified time intervals (Fig. 1). STEERING WHEEL, STEERING COLUMN, OR
Successful completion of the actuator test will con- INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
firm that the instrument cluster is operational. How- SERVICE. FAILURE TO TAKE THE PROPER PRE-
ever, there may still be a problem with the CCD data CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
bus, the Powertrain Control Module (PCM), the Air- BAG DEPLOYMENT AND POSSIBLE PERSONAL
bag Control Module (ACM), the Sentry Key Immobi- INJURY.
lizer Module (SKIM) or the inputs to one of these
electronic control modules. Use a DRB scan tool and
ANTI-LOCK BRAKE SYSTEM LAMP
the proper Diagnostic Procedures manual for testing
of these components. The diagnosis found here addresses an inoperative
If an individual gauge does not respond properly, Anti-lock Brake System (ABS) lamp condition. If the
or does not respond at all during the actuator test, ABS lamp stays on with the ignition switch in the
the instrument cluster should be removed. However, On position, or comes on and stays on while driving,
check that the gauge mounting screws on the instru- refer to Antilock Brakes in the Diagnosis and Test-
ment cluster electronic circuit board for proper tight- ing section of Group 5 - Brakes for diagnosis. If no
ness before considering instrument cluster ABS problem is found, the following procedure will
replacement. If the gauge mounting screws check help locate a short or open in the ABS lamp circuit.
OK, replace the faulty cluster. For complete circuit descriptions, refer to Instru-
If an individual indicator lamp does not illuminate ment Cluster in the Contents of Group 8W - Wiring
during the actuator test, the instrument cluster Diagrams.
should be removed. However, check that the incan- (1) Check the fused ignition switch output (run/
descent lamp bulb is not faulty and that the bulb start) fuse in the fuseblock module. If OK, go to Step
holder is properly installed on the instrument cluster 2. If not OK, repair the shorted circuit or component
electronic circuit board before considering instrument as required and replace the faulty fuse.
cluster replacement. If the bulb and bulb holder (2) Turn the ignition switch to the On position.
check OK, replace the faulty instrument cluster. Check for battery voltage at the fused ignition switch
output (run/start) fuse in the fuseblock module. If
Fig. 1 Instrument Cluster Actuator Test

OK, go to Step 3. If not OK, repair the open fused ignition switch output (run/start) circuit to the igni-
ignition switch output (run/start) circuit to the ignition switch as required.
tion switch as required. (3) Turn the ignition switch to the Off position.
(3) Turn the ignition switch to the Off position. Disconnect and isolate the battery negative cable.
Disconnect and isolate the battery negative cable. Disconnect the wire harness connector at the park
Remove the instrument cluster. Connect the battery brake switch. With the park brake released, check for
negative cable. Turn the ignition switch to the On continuity between the park brake switch terminal
position and within five seconds check for continuity and a good ground. There should be no continuity. If
between the ABS warning indicator driver circuit OK, go to Step 4. If not OK, adjust or replace the
cavity of the instrument cluster wire harness connec- faulty park brake switch.
tor A and a good ground. There should be continuity (4) Disconnect the wire harness connector at the
for five seconds after ignition On, and then an open brake warning switch. Check for continuity between
circuit. If OK, replace the faulty bulb. If not OK, go the two terminals of the brake warning switch. There
to Step 4. should be continuity. If OK, go to Step 5. If not OK,
(4) Turn the ignition switch to the Off position. replace the faulty brake warning switch.
Disconnect and isolate the battery negative cable. (5) Check for continuity between each of the two
Disconnect the Controller Anti-lock Brake (CAB) wire brake warning switch terminals and a good ground.
harness connector. Check for continuity between the In each case, there should be no continuity. If OK, go
ABS warning indicator driver circuit cavity of the to Step 6. If not OK, replace the faulty brake warn-
instrument cluster wire harness connector A and a ing switch.
good ground. There should be no continuity. If OK, go (6) With both the park brake switch and the brake
to Step 5. If not OK, repair the shorted ABS warning warning switch wire harness connectors still discon-
indicator driver circuit as required. nected, check for continuity between the red brake
(5) Check for continuity between the ABS warning warning indicator driver circuit cavity of the park
indicator driver circuit cavities of the instrument brake switch wire harness connector and a good
cluster wire harness connector A and the CAB wire ground. There should be no continuity. If OK, go to
harness connector. There should be continuity. If OK, Step 7. If not OK, repair the shorted red brake warn-
refer to Antilock Brakes in the Diagnosis and Test- ing indicator driver circuit as required.
ing section of Group 5 - Brakes for diagnosis of the (7) With the ignition switch held in the Start posi-
CAB. If not OK, repair the open ABS warning indi- tion, check for continuity between the red brake
cator driver circuit as required. warning indicator driver circuit cavity of the park
brake switch wire harness connector and a good
BRAKE WARNING LAMP ground. There should be continuity. If OK, go to Step
The diagnosis found here addresses an inoperative 8. If not OK, repair the open red brake warning indi-
brake warning lamp condition. If the brake warning cator driver circuit to the ignition switch as required.
lamp stays on with the ignition switch in the On (8) Turn the ignition switch to the Off position.
position and the park brake released, or comes on Remove the instrument cluster. Check for continuity
while driving, refer to Base Brake System for vehi- between the red brake warning indicator driver cir-
cles not equipped with the four wheel anti-lock brake cuit cavity of the instrument cluster wire harness
system, or refer to Antilock Brakes for vehicles connector A and a good ground. There should be no
equipped with the four wheel anti-lock brake system continuity. If OK, go to Step 9. If not OK, repair the
in the Diagnosis and Testing section of Group 5 - shorted red brake warning indicator driver circuit as
Brakes for further diagnosis. If no brake system required.
problem is found, the following procedure will help (9) Check for continuity between the red brake
locate a short or open circuit, or a faulty switch. For warning indicator driver circuit cavities of the instru-
complete circuit diagrams, refer to Instrument ment cluster wire harness connector A and the brake
Cluster in the Contents of Group 8W - Wiring Dia- warning switch wire harness connector. There should
grams. be continuity. If OK, replace the faulty bulb. If not
(1) Check the fused ignition switch output (run/ OK, repair the open red brake warning indicator
start) fuse in the fuseblock module. If OK, go to Step driver circuit as required.
2. If not OK, repair the shorted circuit or component
as required and replace the faulty fuse. CLUSTER ILLUMINATION LAMP
(2) Turn the ignition switch to the On position. The diagnosis found here addresses an inoperative
Check for battery voltage at the fused ignition switch instrument cluster illumination lamp condition. If
output (run/start) fuse in the fuseblock module. If the problem being diagnosed includes inoperative
OK, go to Step 3. If not OK, repair the open fused exterior lighting controlled by the headlamp switch,
that system needs to be repaired first. If the exterior FOUR-WHEEL DRIVE INDICATOR LAMP
lamps controlled by the headlamp switch are inoper- The diagnosis found here addresses an inoperative
ative, refer to Headlamp Diagnosis in the Diagno- four-wheel drive indicator lamp condition. If the
sis and Testing section of Group 8L - Lamps for problem being diagnosed is related to lamp accuracy,
diagnosis. If no exterior lighting system problems are be certain to confirm that the problem is with the
found, the following procedure will help locate a lamp or switch and not with a damaged or inopera-
short or open in the cluster illumination lamp circuit. tive transfer case or transfer case linkage. Refer to
If the problem being diagnosed involves a lack of NV231 Diagnosis in the Diagnosis and Testing sec-
dimming control for the odometer/trip odometer Vac- tion of Group 21 - Transmission for more informa-
uum Fluorescent Display (VFD), but all of the other tion. If no transfer case problem is found, the
cluster illumination lamps can be dimmed, repair the following procedure will help locate a short or open
open headlamp switch output circuit input to the in the indicator lamp circuit. For complete circuit
instrument cluster. For complete circuit diagrams, diagrams, refer to Instrument Cluster in Group 8W
refer to Instrument Cluster in the Contents of - Wiring Diagrams.
Group 8W - Wiring Diagrams. (1) Check the fused ignition switch output (run/
(1) Check the panel lamps dimmer fuse in the start) fuse in the fuseblock module. If OK, go to Step
fuseblock module. If OK, go to Step 2. If not OK, 2. If not OK, repair the shorted circuit or component
repair the shorted circuit or component as required as required and replace the faulty fuse.
and replace the faulty fuse. (2) Turn the ignition switch to the On position.
(2) Turn the park lamps on with the headlamp Check for battery voltage at the fused ignition switch
switch. Rotate the headlamp switch knob counter- output (run/start) fuse in the fuseblock module. If
clockwise to just before the interior lamps detent. OK, go to Step 3. If not OK, repair the open fused
Check for battery voltage at the panel lamps dimmer ignition switch output (run/start) circuit to the igni-
fuse in the fuseblock module. Rotate the headlamp tion switch as required.
switch knob clockwise while observing the test volt- (3) Turn the ignition switch to the Off position.
meter. The reading should go from battery voltage to Disconnect and isolate the battery negative cable.
zero volts. If OK, go to Step 3. If not OK, repair the Disconnect the transfer case switch wire harness con-
open panel lamps dimmer switch signal circuit to the nector. Check for continuity between the ground cir-
headlamp switch as required. If the circuit tests OK, cuit cavity of the transfer case switch wire harness
refer to Headlamp Diagnosis in the Diagnosis and connector and a good ground. There should be conti-
Testing section of Group 8L - Lamps to diagnose the nuity. If OK, go to Step 4. If not OK, repair the open
headlamp switch. ground circuit to ground as required.
(3) Disconnect and isolate the battery negative (4) Connect the battery negative cable. Turn the
cable. Remove the instrument cluster. Turn the head- ignition switch to the On position. Install a jumper
lamp switch off. Remove the panel lamps dimmer wire between the part time four wheel drive indicator
fuse from the fuseblock module. Probe the fused lamp driver circuit cavity of the transfer case switch
panel lamps dimmer switch signal circuit cavity of wire harness connector and a good ground. The four-
the instrument cluster wire harness connector A. wheel drive indicator lamp should light. If OK,
Check for continuity to a good ground. There should replace the faulty transfer case switch. If not OK, go
be no continuity. If OK, go to Step 4. If not OK, to Step 5.
repair the shorted fused panel lamps dimmer switch (5) Turn the ignition switch to the Off position.
signal circuit as required. Disconnect and isolate the battery negative cable.
(4) Install the panel lamps dimmer fuse in the Remove the instrument cluster. With the transfer
fuseblock module. Connect the battery negative case switch wire harness connector still disconnected,
cable. Turn the park lamps on with the headlamp check for continuity between the part time four
switch. Rotate the headlamp switch knob counter- wheel drive indicator lamp driver circuit cavity of the
clockwise to just before the interior lamps detent. instrument cluster wire harness connector B and a
Check for battery voltage at the fused panel lamps good ground. There should be no continuity. If OK, go
dimmer switch signal circuit cavity of the instrument to Step 6. If not OK, repair the shorted part time
cluster wire harness connector A. If OK, replace the four wheel drive indicator lamp driver circuit as
faulty cluster illumination lamp bulb(s) and bulb required.
holder(s). If not OK, repair the open fused panel (6) Check for continuity between the part time
lamps dimmer switch signal circuit as required. four wheel drive indicator lamp driver circuit cavities
of the instrument cluster wire harness connector B
and the transfer case switch wire harness connector.
There should be continuity. If OK, replace the faulty
bulb. If not OK, repair the open part time four wheel ment panel, near the cowl side inner panel in the
drive indicator lamp driver circuit as required. passenger compartment. For complete circuit dia-
grams, refer to Horn/Cigar Lighter in the Contents
HEADLAMP HIGH BEAM INDICATOR LAMP of Group 8W - Wiring Diagrams.
The diagnosis found here addresses an inoperative
headlamp high beam indicator lamp condition. If the WARNING: ON VEHICLES EQUIPPED WITH AIR-
problem being diagnosed is related to inoperative BAGS, REFER TO GROUP 8M - PASSIVE
headlamp high beams, refer to Headlamp Diagno- RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
sis in the Diagnosis and Testing section of Group 8L STEERING WHEEL, STEERING COLUMN, OR
- Lamps for diagnosis of the headlamp system. If no INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
headlamp system problems are found, the following SERVICE. FAILURE TO TAKE THE PROPER PRE-
procedure will help locate an open in the high beam CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
indicator lamp circuit. For complete circuit diagrams, BAG DEPLOYMENT AND POSSIBLE PERSONAL
refer to Instrument Cluster in the Contents of INJURY.
(1) Disconnect and isolate the battery negative (1) Remove the accessory relay from its wire har-
cable. Remove the instrument cluster. ness connector. Refer to Accessory Relay in the
(2) Connect the battery negative cable. Turn the Removal and Installation section of this group for the
headlamps on and select the high beams with the procedures.
multi-function switch stalk. Check for battery voltage (2) A relay in the de-energized position should
at the high beam indicator driver circuit cavity of the have continuity between terminals 87A and 30, and
instrument cluster wire harness connector A. If OK, no continuity between terminals 87 and 30. If OK, go
replace the faulty bulb. If not OK, repair the open to Step 3. If not OK, replace the faulty relay.
high beam indicator driver circuit to the headlamp (3) Resistance between terminals 85 and 86 (elec-
dimmer (multi-function) switch as required. tromagnet) should be 75 6 5 ohms. If OK, go to Step
4. If not OK, replace the faulty relay.
TURN SIGNAL INDICATOR LAMP (4) Connect a battery to terminals 85 and 86.
The diagnosis found here addresses an inoperative There should now be continuity between terminals
turn signal indicator lamp condition. For any other 30 and 87, and no continuity between terminals 87A
turn signal problem, refer to Turn Signal and Haz- and 30. If OK, perform the Relay Circuit Test that
ard Warning Systems in the Diagnosis and Testing follows. If not OK, replace the faulty relay.
section of Group 8J - Turn Signal and Hazard Warn-
ing Systems for further diagnosis. If no turn signal or
hazard warning system problem is found, the follow-
ing procedure will help locate a short or open in the
indicator lamp circuit. For complete circuit diagrams,
refer to Instrument Cluster in the Contents of
cable. Remove the instrument cluster.
(2) Connect the battery negative cable. Activate
the hazard warning system by moving the hazard
warning switch button to the On position. Check for
battery voltage at the inoperative (right or left) turn
signal circuit cavity of the instrument cluster wire
harness connector (connector A - left, or connector B -
right). There should be a switching (on and off) bat-
tery voltage signal. If OK, replace the faulty (right or Fig. 2 Accessory Relay
left) indicator lamp bulb. If not OK, repair the open
(right or left) turn signal circuit to the turn signal/ RELAY CIRCUIT TEST
hazard warning (multi-function) switch as required. (1) The relay common feed terminal (30) is con-
nected to battery voltage and should be hot at all
ACCESSORY RELAY times. Check for battery voltage at the fused B(+) cir-
The accessory relay (Fig. 2) is located in a wire cuit cavity of the accessory relay wire harness con-
harness connector that is secured to the 100-way connector. If OK, go to Step 2. If not OK, repair the
nector bracket under the driver side of the instru- fused B(+) circuit to the fuse in the Power Distribu-
tion Center (PDC) as required.
(2) The relay normally closed terminal (87A) is (2) Turn the ignition switch to the On position.
connected to terminal 30 in the de-energized position, Check for battery voltage at the insulated contact
but is not used for this application. Go to Step 3. located at the back of the cigar lighter/power outlet
(3) The relay normally open terminal (87) is con- receptacle shell. If OK, replace the faulty cigar
nected to the common feed terminal (30) in the ener- lighter knob and element. If not OK, go to Step 3.
gized position. This terminal supplies battery voltage (3) Turn the ignition switch to the Off position.
to the cigar lighter or power outlet when the relay is Disconnect and isolate the battery negative cable.
energized by the ignition switch. There should be Remove the instrument panel accessory switch bezel.
continuity between the accessory relay wire harness Check for continuity between the ground circuit cav-
connector cavity for relay terminal 87 and the acces- ity of the cigar lighter/power outlet wire harness con-
sory relay output circuit cavity in the cigar lighter or nector and a good ground. There should be
power outlet wire harness connector at all times. If continuity. If OK, go to Step 4. If not OK, repair the
OK, go to Step 4. If not OK, repair the open acces- open ground circuit to ground as required.
sory relay output circuit to the cigar lighter or power (4) Connect the battery negative cable. Turn the
outlet wire harness connector as required. ignition switch to the Accessory or On positions.
(4) The coil battery terminal (86) is connected to Check for battery voltage at the accessory relay out-
the electromagnet in the relay. The accessory relay put circuit cavity of the cigar lighter/power outlet
wire harness connector cavity for this terminal wire harness connector. If OK, replace the faulty
should have continuity to ground at all times. If OK, accessory switch bezel unit. If not OK, refer to
go to Step 5. If not OK, repair the open ground cir- Accessory Relay in the Diagnosis and Testing sec-
cuit to ground as required. tion of this group for further diagnosis.
the electromagnet in the relay. It receives battery
feed to energize the accessory relay when the ignition REMOVAL AND INSTALLATION
switch is in the Accessory or On positions. Turn the
ignition switch to the On position. Check for battery STEERING COLUMN OPENING COVER
voltage at the fused ignition switch output (acc/run)
circuit cavity of the accessory relay wire harness con- WARNING: ON VEHICLES EQUIPPED WITH AIR-
nector. If not OK, repair the open fused ignition BAGS, REFER TO GROUP 8M - PASSIVE
switch output (acc/run) circuit to the ignition switch RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
as required. STEERING WHEEL, STEERING COLUMN, OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
INSTRUMENT PANEL CIGAR LIGHTER AND SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
POWER OUTLET BAG DEPLOYMENT AND POSSIBLE PERSONAL
For complete circuit diagrams, refer to Horn/Ci- INJURY.
gar Lighter in the Contents of Group 8W - Wiring
Diagrams.
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR- (1) Disconnect and isolate the battery negative
BAGS, REFER TO GROUP 8M - PASSIVE cable.
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY (2) If the vehicle is so equipped, move the tilt
STEERING WHEEL, STEERING COLUMN, OR steering column to the fully raised position.
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR (3) Remove the knob and shaft from the headlamp
SERVICE. FAILURE TO TAKE THE PROPER PRE- switch. Refer to Headlamp Switch in the Removal
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- and Installation section of this group for the proce-
BAG DEPLOYMENT AND POSSIBLE PERSONAL dures.
INJURY. (4) Remove the two screws that secure the steering
column opening cover to the instrument panel (Fig.
(1) Remove the protective cap or the cigar lighter
3).
knob and element from the cigar lighter/power outlet
(5) Pull the upper edge of the steering column
receptacle shell. Check for continuity between the
opening cover straight back and down away from the
inside circumference of the cigar lighter/power outlet
instrument panel as far as possible.
receptacle shell and a good ground. there should be
(6) Rock the lower edge of the steering column
continuity. If OK, go to Step 2. If not OK, go to Step
opening cover rearward to disengage the hinge hook
3.
formations on the lower edge of the cover from the
hinge pins on the lower edge of the instrument panel.
(3) Remove the four screws that secure the knee
blocker to the instrument panel (Fig. 4).
Fig. 3 Steering Column Opening Cover Remove/

Install
(7) Remove the steering column opening cover Fig. 4 Knee Blocker Remove/Install
from the instrument panel. (4) Remove the knee blocker from the instrument
panel.
INSTALLATION
(1) Position the steering column opening cover to INSTALLATION
the instrument panel. (1) Position the knee blocker to the instrument
(2) Engage the hinge hook formations on the lower panel.
edge of the steering column opening cover with the (2) Install and tighten the four screws that secure
hinge pins on the lower edge of the instrument panel. the knee blocker to the instrument panel. Tighten
(3) Tilt the upper edge of the steering column the screws to 2.2 N·m (20 in. lbs.).
opening cover up into position onto the instrument (3) Install the steering column opening cover onto
panel. the instrument panel. Refer to Steering Column
(4) Install and tighten the two screws that secure Opening Cover in the Removal and Installation sec-
the steering column opening cover to the instrument tion of this group for the procedures.
panel. Tighten the screws to 2.2 N·m (20 in. lbs.). (4) Reconnect the battery negative cable.
HEADLAMP SWITCH
KNEE BLOCKER
WARNING: ON VEHICLES EQUIPPED WITH AIR-
WARNING: ON VEHICLES EQUIPPED WITH AIR- BAGS, REFER TO GROUP 8M - PASSIVE
BAGS, REFER TO GROUP 8M - PASSIVE RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR
STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. FAILURE TO TAKE THE PROPER PRE-
SERVICE. FAILURE TO TAKE THE PROPER PRE- CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- BAG DEPLOYMENT AND POSSIBLE PERSONAL
BAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY.
INJURY.
WARNING: IF THE HEADLAMP SWITCH WAS ON,

REMOVAL WAIT FIVE MINUTES TO ALLOW THE CERAMIC
(1) Disconnect and isolate the battery negative DIMMER RESISTOR TO COOL. IF THE CERAMIC
cable. DIMMER RESISTOR IS NOT ALLOWED TO COOL, IT
(2) Remove the steering column opening cover CAN BURN YOUR FINGERS.
from the instrument panel. Refer to Steering Col-
umn Opening Cover in the Removal and Installa-
tion section of this group for the procedures.
REMOVAL (5) Install the knee blocker onto the instrument
(1) Disconnect and isolate the battery negative panel. Refer to Knee Blocker in the Removal and
cable. Installation section of this group for the procedures.
(2) Pull the headlamp switch control knob out to (6) Insert the shaft of the headlamp switch control
the On position stop. knob and shaft unit through the opening in the steer-
(3) Reach up under the instrument panel outboard ing column opening cover and into the headlamp
of the steering column to access and depress the switch.
headlamp switch control knob and shaft release but- (7) Push the headlamp switch control knob and
ton on the top of the switch body (Fig. 5). shaft unit all the way into the headlamp switch body.
INSTRUMENT PANEL TOP COVER

BAGS, REFER TO GROUP 8M - PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
SERVICE. FAILURE TO TAKE THE PROPER PRE-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
Fig. 5 Headlamp Switch Remove/Install cable.
(4) While holding the release button depressed, (2) Using a trim stick or another suitable wide
pull the headlamp switch control knob and shaft unit flat-bladed tool, gently pry the instrument panel top
out of the headlamp switch. cover up and away from the instrument panel far
(5) Remove the knee blocker from the instrument enough to disengage the five snap clip retainers from
panel. Refer to Knee Blocker in the Removal and their receptacles in the instrument panel (Fig. 6).
Installation section of this group for the procedures.
(6) Remove the spanner nut that secures the head-
lamp switch to the instrument panel mounting
bracket.
(7) Pull the headlamp switch away from the
instrument panel mounting bracket far enough to
access the instrument panel wire harness connectors.
(8) Disconnect the two instrument panel wire har-
ness connectors from the headlamp switch.
(9) Remove the headlamp switch from the instru-
ment panel.
INSTALLATION
(1) Position the headlamp switch to the instru-
ment panel.
(2) Reconnect the two instrument panel wire har-
ness connectors to the headlamp switch.
(3) Position the headlamp switch behind the
mounting bracket on the instrument panel.
(4) Install and tighten the spanner nut that
secures the headlamp switch to the instrument panel
mounting bracket. Tighten the nut to 2.7 N·m (24 in.
lbs.). Fig. 6 Instrument Panel Top Cover Remove/Install
(3) Remove the top cover from the instrument
panel.
INSTALLATION
(1) Position the top cover onto the instrument
panel.
(2) Align the snap clips on the top cover with the
snap clip receptacles in the instrument panel.
(3) Press firmly downward on the top cover over
each of the snap clip locations until each of the snap
clips is fully seated in their receptacles in the instru-
ment panel.
CLUSTER BEZEL
WARNING: ON VEHICLES EQUIPPED WITH AIR- Fig. 7 Cluster Bezel Lower Screws Remove/Install
INJURY.
REMOVAL
cable.
(2) Remove the steering column opening cover
from the instrument panel. Refer to Steering Col- Fig. 8 Cluster Bezel Upper Screws Remove/Install
umn Opening Cover in the Removal and Installa- instrument panel. Tighten the screws to 2.2 N·m (20
tion section of this group for the procedures. in. lbs.).
(3) Remove the top cover from the instrument (4) Install the top cover onto the instrument panel.
panel. Refer to Instrument Panel Top Cover in the Refer to Instrument Panel Top Cover in the
Removal and Installation section of this group for the Removal and Installation section of this group for the
procedures. procedures.
(4) Remove the two screws that secure the lower (5) Install the steering column opening cover onto
mounting tabs of the cluster bezel to the instrument the instrument panel. Refer to Steering Column
panel (Fig. 7). Opening Cover in the Removal and Installation sec-
(5) Remove the three screws that secure the upper tion of this group for the procedures.
mounting flange of the cluster bezel to the instru- (6) Reconnect the battery negative cable.
ment panel (Fig. 8).
(6) Remove the cluster bezel from the instrument INSTRUMENT CLUSTER
panel.
INSTALLATION BAGS, REFER TO GROUP 8M - PASSIVE
(1) Position the cluster bezel to the instrument RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
panel. STEERING WHEEL, STEERING COLUMN, OR
(2) Install and tighten the three screws that secure INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
the upper mounting flange of the cluster bezel to the SERVICE. FAILURE TO TAKE THE PROPER PRE-
instrument panel. Tighten the screws to 2.2 N·m (20 CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
in. lbs.). BAG DEPLOYMENT AND POSSIBLE PERSONAL
(3) Install and tighten the two screws that secure INJURY.
the lower mounting tabs of the cluster bezel to the
REMOVAL lamp bulbs (including the integral bulb holders), the
(1) Disconnect and isolate the battery negative odometer reset knob boot, the cluster lens, the clus-
cable. ter hood and mask unit, the instrument cluster hous-
(2) Remove the cluster bezel from the instrument ing rear cover, and the instrument cluster housing
panel. Refer to Cluster Bezel in the Removal and (including the odometer reset knob, the gauge mask,
Installation section of this group for the procedures. the gauges and the instrument cluster electronic cir-
(3) Remove the four screws that secure the instru- cuit board). Following are the service procedures for
ment cluster to the instrument panel (Fig. 9). the instrument cluster components.

INJURY.
REMOVAL
CLUSTER BULB
This procedure applies to each of the incandescent
cluster illumination lamp or indicator lamp bulb and
Fig. 9 Instrument Cluster Remove/Install bulb holder units. However, the illumination lamps
(4) Pull the instrument cluster rearward far and the indicator lamps use different bulb and bulb
enough to disengage the two self-docking instrument holder unit sizes. They must never be interchanged.
panel wire harness connectors from the connector Be certain that any bulb and bulb holder unit
receptacles on the back of the cluster housing. removed from the cluster electronic circuit board is
(5) Remove the instrument cluster from the instru- reinstalled in the correct position. Always use the
ment panel. correct bulb size and type for replacement. An incor-
rect bulb size or type may overheat and cause dam-
INSTALLATION age to the instrument cluster, the electronic circuit
(1) Position the instrument cluster to the instru- board and/or the gauges.
ment panel. (1) Disconnect and isolate the battery negative
(2) Align the instrument cluster with the cluster cable.
opening in the instrument panel and push the cluster (2) Remove the instrument cluster from the instru-
firmly and evenly into place. The instrument panel ment panel. Refer to Instrument Cluster in the
has two self-docking wire harness connectors that Removal and Installation section of this group for the
will be automatically aligned with, and connected to procedures.
the cluster connector receptacles when the cluster is (3) Turn the bulb holder counterclockwise about
installed in the instrument panel. sixty degrees on the cluster electronic circuit board.
(3) Install and tighten the four screws that secure (4) Pull the bulb and bulb holder unit straight
the instrument cluster to the instrument panel. back to remove it from the bulb mounting hole in the
Tighten the screws to 2.2 N·m (20 in. lbs.). cluster electronic circuit board (Fig. 10).
(4) Install the cluster bezel onto the instrument
CLUSTER LENS
panel. Refer to Cluster Bezel in the Removal and
Installation section of this group for the procedures. (1) Disconnect and isolate the battery negative
(5) Reconnect the battery negative cable. cable.
(2) Remove the instrument cluster from the instru-
INSTRUMENT CLUSTER COMPONENTS ment panel. Refer to Instrument Cluster in the
Removal and Installation section of this group for the
Some of the components for the instrument cluster
procedures.
used in this vehicle are serviced individually. The
(3) Work around the perimeter of the cluster hous-
serviced components include: the incandescent
ing to disengage each of the latches that secure the
instrument cluster indicator lamp and illumination
cluster lens to the cluster housing (Fig. 11).
CLUSTER HOOD AND MASK
cable.
ment panel. Refer to Instrument Cluster in the
procedures.
(3) Remove the cluster lens from the cluster hous-
ing. Refer to Instrument Cluster Components -
Cluster Lens in the Removal and Installation sec-
tion of this group for the procedures.
(4) Work around the perimeter of the cluster hous-
ing to disengage each of the latches that secure the
Fig. 10 Cluster Bulb Locations cluster hood and mask unit to the cluster housing
(4) Gently pull the cluster lens away from the clus- (Fig. 11).
ter housing. (5) Gently pull the cluster hood and mask unit
away from the cluster housing.
ODOMETER RESET KNOB BOOT
(1) Disconnect and isolate the battery negative CLUSTER HOUSING REAR COVER
cable. (1) Disconnect and isolate the battery negative
(2) Remove the instrument cluster from the instru- cable.
ment panel. Refer to Instrument Cluster in the (2) Remove the instrument cluster from the instru-
Removal and Installation section of this group for the ment panel. Refer to Instrument Cluster in the
procedures. Removal and Installation section of this group for the
(3) Remove the cluster lens from the cluster hous- procedures.
ing. Refer to Instrument Cluster Components - (3) Work around the perimeter of the cluster hous-
Cluster Lens in the Removal and Installation sec- ing to disengage each of the latches that secure the
tion of this group for the procedures. rear cover to the cluster housing (Fig. 11).
(4) Remove the odometer reset knob boot by pull- (4) Gently pull the rear cover away from the back
ing it out of the cluster lens. of the cluster housing.
Fig. 11 Instrument Cluster Components

CLUSTER HOUSING (2) Press firmly and evenly on the cluster lens to
(1) Disconnect and isolate the battery negative install it onto the cluster housing.
cable. (3) Work around the perimeter of the cluster hous-
(2) Remove the instrument cluster from the instru- ing to be certain that each of the latches that secure
ment panel. Refer to Instrument Cluster in the the cluster lens to the cluster housing is fully
Removal and Installation section of this group for the engaged.
procedures. (4) Install the instrument cluster onto the instru-
(3) Remove all of the cluster illumination lamp ment panel. Refer to Instrument Cluster in the
and indicator lamp bulb and bulb holder units from Removal and Installation section of this group for the
the electronic circuit board. Refer to Instrument procedures.
Cluster Components - Cluster Bulbs in the (5) Reconnect the battery negative cable.
procedures. ODOMETER RESET KNOB BOOT
(4) Remove the cluster hood and mask unit from (1) Position the odometer reset knob to the mount-
the cluster housing. Refer to Instrument Cluster ing hole from the back of the cluster lens.
Components - Cluster Hood and Mask in the (2) Pull the odometer reset knob into the mounting
Removal and Installation section of this group for the hole from the face of the cluster lens.
procedures. (3) Install the cluster lens onto the cluster hous-
(5) Remove the rear cover from the cluster housing. Refer to Instrument Cluster Components -
ing. Refer to Instrument Cluster Components - Cluster Lens in the Removal and Installation sec-
Cluster Housing Rear Cover in the Removal and tion of this group for the procedures.
Installation section of this group for the procedures. (4) Install the instrument cluster onto the instru-
INSTALLATION Removal and Installation section of this group for the
procedures.
CLUSTER BULB (5) Reconnect the battery negative cable.
This procedure applies to each of the incandescent
cluster illumination lamp or indicator lamp bulb and CLUSTER HOOD AND MASK
bulb holder units. However, the illumination lamps (1) Align the hood and mask unit with the cluster
and the indicator lamps use different bulb and bulb housing.
holder unit sizes. They must never be interchanged. (2) Press firmly and evenly on the hood and mask
Be certain that any bulb and bulb holder unit unit to install it onto the cluster housing.
removed from the cluster electronic circuit board is (3) Work around the perimeter of the cluster hous-
reinstalled in the correct position. ing to be certain that each of the latches that secure
the hood and mask unit to the cluster housing is
CAUTION: Always use the correct bulb size and fully engaged.
type for replacement. An incorrect bulb size or type (4) Install the cluster lens onto the cluster hous-
may overheat and cause damage to the instrument ing. Refer to Instrument Cluster Components -
cluster, the electronic circuit board and/or the Cluster Lens in the Removal and Installation sec-
gauges. tion of this group for the procedures.
(5) Install the instrument cluster onto the instru-
(1) Insert the bulb and bulb holder unit straight ment panel. Refer to Instrument Cluster in the
into the correct bulb mounting hole in the cluster Removal and Installation section of this group for the
electronic circuit board. procedures.
(2) With the bulb holder fully seated against the (6) Reconnect the battery negative cable.
cluster electronic circuit board, turn the bulb holder
clockwise about sixty degrees to lock it into place. CLUSTER HOUSING REAR COVER
(3) Install the instrument cluster onto the instru- (1) Position the rear cover to the back of the clus-
ment panel. Refer to Instrument Cluster in the ter housing.
Removal and Installation section of this group for the (2) Press firmly and evenly on the rear cover until
procedures. each of the latches that secure the rear cover to the
(4) Reconnect the battery negative cable. cluster housing is fully engaged.
CLUSTER LENS ment panel. Refer to Instrument Cluster in the
(1) Align the cluster lens with the cluster hood and Removal and Installation section of this group for the
mask unit. procedures.
CLUSTER HOUSING
(1) Install the rear cover onto the cluster housing.
Refer to Instrument Cluster Components - Clus-
ter Housing Rear Cover in the Removal and
(2) Install the cluster hood and mask unit onto the
cluster housing. Refer to Instrument Cluster Com-
ponents - Cluster Hood and Mask in the Removal
and Installation section of this group for the proce-
dures.
(3) Install all of the cluster illumination lamp and
indicator lamp bulb and bulb holder units into the
electronic circuit board. Refer to Instrument Clus-
ter Components - Cluster Bulbs in the Removal
and Installation section of this group for the proce-
dures.
procedures.
INSTRUMENT PANEL CENTER BEZEL

BAGS, REFER TO GROUP 8M - PASSIVE Fig. 12 Instrument Panel Center Bezel Remove/
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY Install
STEERING WHEEL, STEERING COLUMN, OR (8) Remove the center bezel from the instrument
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR panel.
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- INSTALLATION
BAG DEPLOYMENT AND POSSIBLE PERSONAL (1) Position the center bezel to the instrument
INJURY. panel.
(2) Align the snap clips on the center bezel with
REMOVAL the receptacles in the instrument panel.
(3) Press firmly on the center bezel over each of
the snap clip locations until each of the snap clips is
cable.
fully engaged in its receptacle on the instrument
(2) Remove the top cover from the instrument
panel.
panel. Refer to Instrument Panel Top Cover in the
(4) Install and tighten the two screws that secure
the top of the center bezel to the top of the instru-
procedures.
ment panel. Tighten the screws to 2.2 N·m (20 in.
(3) Remove the ash receiver from the ash receiver
lbs.).
housing in the lower portion of the instrument panel
Install and tighten the one screw into the back of
center bezel.
the ash receiver housing that secures the lower por-
(4) Remove the one screw from the back of the ash
tion of the center bezel to the instrument panel.
receiver housing that secures the lower portion of the
Tighten the screw to 2.2 N·m (20 in. lbs.).
center bezel to the instrument panel (Fig. 12).
(5) Install the ash receiver into the ash receiver
(5) Remove the two screws that secure the top of
housing in the lower portion of the instrument panel
the center bezel to the top of the instrument panel.
center bezel.
(6) Using a trim stick or another suitable wide
(6) Install the top cover onto the instrument panel.
flat-bladed tool, gently pry the lower edge of the cen-
Refer to Instrument Panel Top Cover in the
ter bezel away from the instrument panel.
(7) Pull the lower edge of the center bezel away
procedures.
from the instrument panel far enough to disengage
the four snap clip retainers that secure it from the
receptacles in the instrument panel.
INSTRUMENT PANEL ACCESSORY SWITCH INSTALLATION

BEZEL (1) Position the accessory switch bezel to the
instrument panel.
WARNING: ON VEHICLES EQUIPPED WITH AIR- (2) Reconnect the instrument panel wire harness
BAGS, REFER TO GROUP 8M - PASSIVE connectors to the connector receptacles, the accessory
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY switches and the cigar lighter/power outlet on the
STEERING WHEEL, STEERING COLUMN, OR back of the accessory switch bezel.
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR (3) Position the accessory switch bezel onto the
SERVICE. FAILURE TO TAKE THE PROPER PRE- instrument panel.
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- (4) Install and tighten the four screws that secure
BAG DEPLOYMENT AND POSSIBLE PERSONAL the accessory switch bezel to the instrument panel.
INJURY. Tighten the screws to 2.2 N·m (20 in. lbs.).
(5) Install the center bezel onto the instrument
panel. Refer to Instrument Panel Center Bezel in
REMOVAL the Removal and Installation section of this group for
(1) Disconnect and isolate the battery negative the procedures.
cable. (6) Reconnect the battery negative cable.
(2) Remove the center bezel from the instrument
panel. Refer to Instrument Panel Center Bezel in ACCESSORY RELAY
the Removal and Installation section of this group for
the procedures. WARNING: ON VEHICLES EQUIPPED WITH AIR-
(3) Remove the four screws that secure the acces- BAGS, REFER TO GROUP 8M - PASSIVE
sory switch bezel to the instrument panel (Fig. 13). RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
INJURY.
REMOVAL
cable.
(2) Reach up under the instrument panel outboard
of the steering column to access the accessory relay
and the accessory relay wire harness connector,
which is secured to the 100-way wire harness connec-
tor mounting bracket (Fig. 14).
Fig. 13 Instrument Panel Accessory Switch Bezel

Remove/Install
(4) Pull the accessory switch bezel away from the
instrument panel far enough to access the instru-
ment panel wire harness connectors.
(5) Disconnect the instrument panel wire harness
connectors from the connector receptacles, the acces-
sory switches and the cigar lighter/power outlet on
the back of the accessory switch bezel.
(6) Remove the accessory switch bezel from the
instrument panel.
Fig. 14 Accessory Relay Remove/Install

(3) Disconnect the accessory relay from the acces-
sory relay wire harness connector.
(4) Remove the accessory relay from under the
instrument panel.
INSTALLATION
(1) Position the accessory relay to the accessory
relay wire harness connector under the instrument
panel.
(2) Align the terminals of the accessory relay with
the cavities in the accessory relay wire harness con-
nector.
(3) Push on the accessory relay case firmly and
evenly until all of the relay terminals are fully seated
within the cavities of the accessory relay wire har-
ness connector.
GLOVE BOX
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY Fig. 15 Glove Box Remove/Install
door as possible and slide the rolled end of the check
strap into the slot in the edge of the door.
(5) Close the glove box door.
INJURY.
GLOVE BOX COMPONENTS
Service of all of the glove box components (Fig. 16)
REMOVAL must be performed with the glove box removed from
(1) Disconnect and isolate the battery negative the instrument panel.
cable.
(2) Release the glove box latch and open the glove
box door.
(3) While supporting the glove box door with one
hand, grasp the check strap as close to the glove box
door as possible and slide the rolled end of the check
strap out of the slot in the edge of the door (Fig. 15).
(4) Lower the glove box door far enough to disen-
gage the hinge hook formations on the lower edge of
INJURY.
the door from the hinge pins on the lower edge of the
instrument panel.
(5) Remove the glove box from the instrument REMOVAL
panel.
GLOVE BOX DOOR AND BIN
INSTALLATION (1) Disconnect and isolate the battery negative
(1) Position the glove box to the instrument panel. cable.
(2) Engage the hinge hook formations on the lower (2) Remove the glove box from the instrument
edge of the glove box door with the hinge pins on the panel. Refer to Glove Box in the Removal and
lower edge of the instrument panel. Installation section of this group for the procedures.
(3) Tilt the upper edge of the glove box door up (3) Remove the screws that secure the glove box
toward the instrument panel far enough to engage latch and handle to the glove box door.
the check strap with the door. (4) Remove the screws that secure the inner door
(4) While supporting the glove box door with one and bin unit to the outer glove box door.
hand, grasp the check strap as close to the glove box
(5) Insert a small screwdriver into the retaining
tumbler release slot and depress the retaining tum-
bler (Fig. 17).
Fig. 16 Glove Box Components

(5) Remove the inner door and bin unit from the
outer glove box door.
Fig. 17 Glove Box Lock Cylinder Remove/Install
GLOVE BOX CHECK STRAP
(6) Pull the lock cylinder out of the glove box latch
(1) Disconnect and isolate the battery negative handle by using a gentle twisting and pulling action
cable. on the key.
(2) Remove the glove box from the instrument
panel. Refer to Glove Box in the Removal and INSTALLATION
(3) Remove the screw that secures the glove box GLOVE BOX DOOR AND BIN
check strap to the instrument panel above the glove (1) Position the inner door and bin unit onto the
box opening. outer glove box door.
(4) Remove the check strap from the instrument (2) Install and tighten the screws that secure the
panel. inner door and bin unit to the outer glove box door.
Tighten the screws to 2.2 N·m (20 in. lbs.).
GLOVE BOX LATCH AND HANDLE
(3) Install and tighten the screws that secure the
(1) Disconnect and isolate the battery negative glove box latch and handle to the glove box door.
cable. Tighten the screws to 2.2 N·m (20 in. lbs.).
(2) Remove the glove box from the instrument (4) Install the glove box onto the instrument panel.
panel. Refer to Glove Box in the Removal and Refer to Glove Box in the Removal and Installation
Installation section of this group for the procedures. section of this group for the procedures.
(3) Remove the four screws that secure the glove (5) Reconnect and isolate the battery negative
box latch and handle to the glove box door from the cable.
inside of the glove box.
(4) Remove the latch and handle from the glove GLOVE BOX CHECK STRAP
box door. (1) Position the check strap to the instrument
panel.
GLOVE BOX LOCK CYLINDER
(2) Install and tighten the screw that secures the
(1) Disconnect and isolate the battery negative glove box check strap to the instrument panel above
cable. the glove box opening. Tighten the screw to 2.2 N·m
(2) Remove the glove box from the instrument (20 in. lbs.).
panel. Refer to Glove Box in the Removal and (3) Install the glove box onto the instrument panel.
Installation section of this group for the procedures. Refer to Glove Box in the Removal and Installation
(3) Remove the glove box latch and handle from section of this group for the procedures.
the glove box. Refer to Glove Box Components - (4) Reconnect the battery negative cable.
Glove Box Latch and Handle in the Removal and
Installation section of this group for the procedures. GLOVE BOX LATCH AND HANDLE
(4) Insert the key into the glove box lock cylinder. (1) Position the latch and handle onto the glove
box door.
(2) Install and tighten the four screws that secure (4) Remove the latch striker from the instrument
the glove box latch and handle to the glove box door panel.
from the inside of the glove box. Tighten the screws
to 2.2 N·m (20 in. lbs.). INSTALLATION
(3) Install the glove box onto the instrument panel. (1) Position the latch striker onto the instrument
Refer to Glove Box in the Removal and Installation panel.
section of this group for the procedures. (2) Install and tighten the two screws that secure
(4) Reconnect the battery negative cable. the latch striker to the grab handle bezel at the top
of the instrument panel glove box opening. Tighten
GLOVE BOX LOCK CYLINDER the screws to 2.2 N·m (20 in. lbs.).
(1) Insert the key into the glove box lock cylinder. (3) Install the glove box onto the instrument panel.
(2) Push the lock cylinder into the glove box latch Refer to Glove Box in the Removal and Installation
handle by using a gentle twisting and pushing action section of this group for the procedures.
on the key. (4) Reconnect the battery negative cable.
(3) Install the glove box latch and handle onto the
glove box. Refer to Glove Box Components - Glove INSTRUMENT PANEL GRAB HANDLE
Box Latch and Handle in the Removal and Instal-
lation section of this group for the procedures. WARNING: ON VEHICLES EQUIPPED WITH AIR-
(4) Install the glove box onto the instrument panel. BAGS, REFER TO GROUP 8M - PASSIVE
Refer to Glove Box in the Removal and Installation RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
section of this group for the procedures. STEERING WHEEL, STEERING COLUMN, OR
(5) Reconnect the battery negative cable. INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
GLOVE BOX LATCH STRIKER CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
WARNING: ON VEHICLES EQUIPPED WITH AIR- INJURY.
STEERING WHEEL, STEERING COLUMN, OR REMOVAL
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR (1) Disconnect and isolate the battery negative
SERVICE. FAILURE TO TAKE THE PROPER PRE- cable.
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- (2) Remove the glove box from the instrument
BAG DEPLOYMENT AND POSSIBLE PERSONAL panel. Refer to Glove Box in Removal and Installa-
INJURY. tion section of this group for the procedures.
(3) Reach through and above the glove box opening
to access and remove the two nuts that secure the
REMOVAL stud on each end of the grab handle to the instru-
(1) Disconnect and isolate the battery negative ment panel (Fig. 19). Discard the used grab handle
cable. mounting nuts.
panel. Refer to Glove Box in the Removal and
(3) Remove the two screws that secure the latch
striker to the grab handle bezel at the top of the
instrument panel glove box opening (Fig. 18).
Fig. 19 Instrument Panel Grab Handle Remove/

Install
(4) Remove the grab handle from the instrument
panel.
Fig. 18 Glove Box Latch Striker Remove/Install

INSTALLATION (3) Install the glove box latch striker onto the
(1) Position the grab handle onto the instrument instrument panel. Refer to Glove Box Latch
panel. Striker in the Removal and Installation section of
(2) Reach through and above the glove box opening this group for the procedures.
to install and tighten the two nuts that secure the (4) Install the grab handle onto the instrument
stud on each end of the grab handle to the instru- panel. Refer to Instrument Panel Grab Handle in
ment panel. Tighten the nuts to 5.6 N·m (50 in. lbs.). the Removal and Installation section of this group for
(3) Install the glove box onto the instrument panel. the procedures.
Refer to Glove Box in Removal and Installation sec- (5) Reconnect the battery negative cable.
(4) Reconnect the battery negative cable. INSTRUMENT PANEL ASSEMBLY
INSTRUMENT PANEL GRAB HANDLE BEZEL WARNING: ON VEHICLES EQUIPPED WITH AIR-
WARNING: ON VEHICLES EQUIPPED WITH AIR- RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
BAGS, REFER TO GROUP 8M - PASSIVE STEERING WHEEL, STEERING COLUMN, OR
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
STEERING WHEEL, STEERING COLUMN, OR SERVICE. FAILURE TO TAKE THE PROPER PRE-
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
SERVICE. FAILURE TO TAKE THE PROPER PRE- BAG DEPLOYMENT AND POSSIBLE PERSONAL
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- INJURY.
INJURY.
REMOVAL
REMOVAL NOTE: Before starting this procedure, be certain to

(1) Disconnect and isolate the battery negative turn the steering wheel until the front wheels are in
cable. the straight-ahead position.
(2) Remove the grab handle from the instrument
panel. Refer to Instrument Panel Grab Handle in
cable.
the Removal and Installation section of this group for
(2) Remove the knee blocker from the instrument
the procedures.
panel. Refer to Knee Blocker in the Removal and
(3) Remove the glove box latch striker from the
instrument panel. Refer to Glove Box Latch
(3) Remove the steering column from the vehicle,
Striker in the Removal and Installation section of
but do not remove the driver side airbag module, the
this group for the procedures.
steering wheel, or the switches from the steering col-
(4) Remove the two screws that secure the grab
umn. Be certain that the steering wheel is locked
handle bezel to the instrument panel (Fig. 20).
and secured from rotation to prevent the loss of
clockspring centering. Refer to Steering Column in
the Removal and Installation section of Group 19 -
Steering for the procedures.
(4) From under the driver side of the instrument
panel, perform the following:
(a) Disconnect the instrument panel wire har-
ness connectors from the 100-way wire harness
Fig. 20 Instrument Panel Grab Handle Bezel connector near the left cowl side inner panel.
Remove/Install (b) Disconnect the side window demister hose at
(5) Remove the grab handle bezel from the instru- the heater-A/C housing demister/defroster duct
ment panel. (driver side).
INSTALLATION panel. Refer to Glove Box in the Removal and
(1) Position the grab handle bezel onto the instru- Installation section of this group for the procedures.
ment panel. (6) Reach through the instrument panel glove box
(2) Install and tighten the two screws that secure opening to perform the following:
the grab handle bezel to the instrument panel. (a) Disconnect the two halves of the heater-A/C
Tighten the screws to 2.2 N·m (20 in. lbs.). system vacuum harness connector.
(b) Disconnect the instrument panel wire har-
ness connector from the heater-A/C system wire
harness connector.
(c) Disconnect the instrument panel wire har-
ness connector from the passenger side airbag
module wire harness connector.
(d) Disconnect the side window demister hose at
the heater-A/C housing demister/defroster duct
(passenger side).
(e) Disconnect the two halves of the radio
antenna coaxial cable connector.
(f) Disconnect the two instrument panel wire
harness connectors from the passenger airbag
on/off switch wire harness connectors.
(g) Disengage the passenger side airbag on/off
switch wire harness from the retainer clip on the
plenum bracket that supports the heater-A/C hous- Fig. 22 Instrument Panel Assembly Remove/Install
ing just inboard of the fuseblock module.
(h) Remove the two nuts that secure the lower
INSTALLATION
(1) With the aid of an assistant, install the instru-
passenger side airbag module bracket to the studs
ment panel assembly onto the dash panel studs in
on the dash panel (Fig. 21).
the vehicle.
(2) Install and tighten the four nuts that secure
the top of the instrument panel to the studs on the
top of the dash panel. Tighten the nuts to 12 N·m
(105 in. lbs.).
(3) Install and tighten the three screws that secure
each end of the instrument panel to the door hinge
pillars. Tighten the screws to 12 N·m (105 in. lbs.).
(4) Install the top cover onto the instrument panel.
Refer to Instrument Panel Top Cover in the
procedures.
(5) Reach through the instrument panel glove box
opening to perform the following:
(a) Install and tighten the two nuts that secure
the lower passenger side airbag module bracket to
the studs on the dash panel. Tighten the nuts to 28
Fig. 21 Passenger Airbag Module Lower Bracket N·m (250 in. lbs.).
Nuts Remove/Install (b) Engage the passenger side airbag on/off
(7) Remove the top cover from the instrument switch wire harness in the retainer clip on the ple-
panel. Refer to Instrument Panel Top Cover in the num bracket that supports the heater-A/C housing
Removal and Installation section of this group for the just inboard of the fuseblock module.
procedures. (c) Reconnect the two instrument panel wire
(8) Remove the three screws that secure each end harness connectors to the passenger airbag on/off
of the instrument panel to the door hinge pillars (Fig. switch wire harness connectors.
22). (d) Reconnect the two halves of the radio
(9) Remove the four nuts that secure the top of the antenna coaxial cable connector.
instrument panel to the studs on the top of the dash (e) Reconnect the side window demister hose to
panel. the heater-A/C housing demister/defroster duct
(10) With the aid of an assistant, lift the instru- (passenger side).
ment panel assembly off of the dash panel studs and (f) Reconnect the instrument panel wire harness
remove it from the vehicle. connector to the passenger side airbag module wire
harness connector.
(g) Reconnect the instrument panel wire harness
connector to the heater-A/C system wire harness
connector.
(h) Reconnect the two halves of the heater-A/C (6) Remove the radio from the instrument panel.
system vacuum harness connector. Refer to Radio in the Removal and Installation sec-
(6) Install the glove box onto the instrument panel. tion of Group 8F - Audio Systems for the procedures.
Refer to Glove Box in the Removal and Installation (7) Remove the heater-A/C control from the instru-
section of this group for the procedures. ment panel. Refer to Heater-A/C Control in the
(7) From under the driver side of the instrument Removal and Installation section of Group 24 - Heat-
panel, perform the following: ing and Air Conditioning Systems for the procedures.
(a) Reconnect the side window demister hose to (8) Remove the outboard heater-A/C panel outlets
the heater-A/C housing demister/defroster duct from the instrument panel. Refer to Ducts and Out-
(driver side). lets in the Removal and Installation section of Group
(b) Reconnect the instrument panel wire harness 24 - Heating and Air Conditioning Systems for the
connectors to the 100-way wire harness connector procedures.
near the left cowl side inner panel. (9) Remove the instrument panel assembly from
(8) Install the steering column into the vehicle. Be the vehicle. Refer to Instrument Panel Assembly
certain that the steering wheel is locked and secured in the Removal and Installation section of this group
from rotation to prevent the loss of clockspring cen- for the procedures.
tering. Refer to Steering Column in the Removal (10) Place the instrument panel on a suitable work
and Installation section of Group 19 - Steering for surface. Be certain to take the proper precautions to
the procedures. protect the instrument panel from any possible cos-
(9) Install the knee blocker onto the instrument metic damage.
panel. Refer to Knee Blocker in the Removal and (11) Remove the passenger side airbag door from
Installation section of this group for the procedures. the instrument panel. Refer to Passenger Side Air-
(10) Reconnect the battery negative cable. bag Door in the Removal and Installation section of
Group 8M - Passive Restraint Systems for the proce-
INSTRUMENT PANEL BASE TRIM dures.
(12) Remove the two screws that secure the
WARNING: ON VEHICLES EQUIPPED WITH AIR- 16-way data link wire harness connector to the
BAGS, REFER TO GROUP 8M - PASSIVE instrument panel.
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY (13) Remove the screws around the perimeter that
STEERING WHEEL, STEERING COLUMN, OR secure the base trim to the instrument panel.
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR (14) Remove the base trim from the instrument
SERVICE. FAILURE TO TAKE THE PROPER PRE- panel.
BAG DEPLOYMENT AND POSSIBLE PERSONAL INSTALLATION
INJURY. (1) Position the base trim onto the instrument
panel.
(2) Install and tighten the screws around the
REMOVAL perimeter that secure the base trim to the instru-
(1) Disconnect and isolate the battery negative ment panel. Tighten the screws to 2.2 N·m (20 in.
cable. lbs.).
(2) Remove the instrument cluster from the instru- (3) Install and tighten the two screws that secure
ment panel. Refer to Instrument Cluster in the the 16-way data link wire harness connector to the
Removal and Installation section of this group for the instrument panel. Tighten the screws to 2.2 N·m (20
procedures. in. lbs.).
(3) Remove the accessory switch bezel from the (4) Install the passenger side airbag door onto the
instrument panel. Refer to Instrument Panel instrument panel. Refer to Passenger Side Airbag
Accessory Switch Bezel in the Removal and Instal- Door in the Removal and Installation section of
lation section of this group for the procedures. Group 8M - Passive Restraint Systems for the proce-
(4) Remove the grab handle bezel from the instru- dures.
ment panel. Refer to Instrument Panel Grab Han- (5) Install the instrument panel assembly into the
dle Bezel in the Removal and Installation section of vehicle. Refer to Instrument Panel Assembly in
this group for the procedures. the Removal and Installation section of this group for
(5) Remove the speaker bezels from the instru- the procedures.
ment panel. Refer to Instrument Panel Speakers (6) Install the outboard heater-A/C panel outlets
in the Removal and Installation section of Group 8F - onto the instrument panel. Refer to Ducts and Out-
Audio Systems for the procedures. lets in the Removal and Installation section of Group
24 - Heating and Air Conditioning Systems for the dle Bezel in the Removal and Installation section of
procedures. this group for the procedures.
(7) Install the heater-A/C control onto the instru- (11) Install the accessory switch bezel onto the
ment panel. Refer to Heater-A/C Control in the instrument panel. Refer to Instrument Panel
Removal and Installation section of Group 24 - Heat- Accessory Switch Bezel in the Removal and Instal-
ing and Air Conditioning Systems for the procedures. lation section of this group for the procedures.
(8) Install the radio onto the instrument panel. (12) Install the instrument cluster onto the instru-
Refer to Radio in the Removal and Installation sec- ment panel. Refer to Instrument Cluster in the
tion of Group 8F - Audio Systems for the procedures. Removal and Installation section of this group for the
(9) Install the speaker bezels onto the instrument procedures.
panel. Refer to Instrument Panel Speakers in the (13) Reconnect the battery negative cable.
Removal and Installation section of Group 8F - Audio
Systems for the procedures.
(10) Install the grab handle bezel onto the instru-
ment panel. Refer to Instrument Panel Grab Han-
INSTRUMENT PANEL SYSTEMS

CONTENTS
page page
REMOVAL AND INSTALLATION REAR FOGLAMP SWITCH . . . . . . . . . . . . . . . . . 2

HEADLAMP LEVELING SWITCH . . . . . . . . . . . . . 1
REMOVAL AND INSTALLATION (2) Disconnect the headlamp leveling switch elec-
trical connector (Fig. 2) and remove the headlamp
HEADLAMP LEVELING SWITCH leveling switch.

INJURY.
REMOVAL
(1) Using a flat blade screwdriver or similar tool
between the headlamp leveling switch and the steer-
ing column cover (Fig. 1). Gently pry the headlamp
leveling switch out of the steering column cover.
Fig. 2 Headlamp Leveling Switch Electrical

Connector
INSTALLATION
(1) Connect the headlamp leveling switch electrical
connector.
(2) Install the headlamp leveling switch into the
steering column cover.
Fig. 1 Headlamp Leveling Switch

REAR FOGLAMP SWITCH
REMOVAL

INJURY.
(1) Using a flat blade screwdriver or similar flat-

bladed tool, gently pry the instrument panel top
cover up and away from the instrument panel to
release the snap clip retainers (Fig. 3).
Fig. 4 Center Bezel Lower Screw

(5) Remove the screws that secure the center bezel
to the top of the instrument panel (Fig. 5).
Fig. 3 Instrument Panel Top Cover

(2) Remove the instrument panel top cover from
the vehicle.
(3) Remove the ash receiver from the center bezel.
(4) Remove the screw located in back of the ash
receiver housing that secures the center bezel to the
lower instrument panel (Fig. 4).
Fig. 5 Center Bezel Mounting Screws

(6) Remove the instrument panel center bezel.
(7) Remove the screws attaching the accessory
switch bezel to the instrument panel (Fig. 6).
(8) Disconnect the rear foglamp switch electrical
connector.
(9) Remove the rear foglamp switch from the
accessory switch bezel.
INSTALLATION
(1) Install the rear foglamp switch to the accessory
switch bezel.
(2) Connect the rear foglamp switch electrical con-
nector to the switch.
(3) Install the screws attaching the accessory
switch bezel to the instrument panel (Fig. 6).
(4) Install the instrument panel center bezel and
attaching screws.
(5) Install the ash receiver.
(6) Install the instrument panel top cover.
Fig. 6 Accessory Switch Bezel
TJ AUDIO SYSTEMS 8F - 1
AUDIO SYSTEMS
CONTENTS
page page
GENERAL INFORMATION AUDIO SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1 RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DESCRIPTION AND OPERATION RADIO FREQUENCY INTERFERENCE . . . . . . . . . 6
ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SPEAKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
IGNITION-OFF DRAW FUSE . . . . . . . . . . . . . . . . 1 REMOVAL AND INSTALLATION
RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
RADIO NOISE SUPPRESSION . . . . . . . . . . . . . . 2 RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SPEAKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 RADIO NOISE SUPPRESSION COMPONENTS . . 9
DIAGNOSIS AND TESTING SOUND BAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SPEAKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
GENERAL INFORMATION When removing or installing the IOD fuse, it is

important that the ignition switch be in the Off posi-
INTRODUCTION tion. Failure to place the ignition switch in the Off
An audio system is standard factory-installed position can cause the radio display to become scram-
equipment on this model, unless the vehicle is bled when the IOD fuse is removed and replaced.
ordered with an available radio delete option. Refer Removing and replacing the IOD fuse again, with the
to 8W-47 - Audio System in Group 8W - Wiring Dia- ignition switch in the Off position, will correct the
grams for complete circuit descriptions and diagrams. scrambled display condition.
The IOD fuse should be checked if the radio is
inoperative. The IOD fuse is located in the Power
DESCRIPTION AND OPERATION Distribution Center (PDC). Refer to the PDC label for
IOD fuse identification and location.
RADIO
Available factory-installed radio receivers for this SPEAKER
model include an AM/FM (RAL sales code), and an The standard equipment speaker system includes
AM/FM/cassette (RAS sales code). All factory-in- two full-range speakers. Each speaker is mounted
stalled radio receivers are stereo Electronically behind a removable bezel located on the outboard
Tuned Radios (ETR), and include an electronic digital ends of the lower instrument panel.
clock function. The sound bar option adds two full-range speakers
The radio can only be serviced by an authorized to the standard speaker system, for a total of four
radio repair station. Refer to the latest Warranty Pol- speakers. Each of the additional speakers is mounted
icies and Procedures manual for a current listing of behind a grille located on the outboard ends of the
authorized radio repair stations. sound bar, which is attached from side-to-side to the
For more information on radio features, setting sport bar above the rear seating area of the vehicle.
procedures, and control functions refer to the owner’s
manual in the vehicle glove box. ANTENNA
All models use a fixed-length stainless steel rod-
IGNITION-OFF DRAW FUSE type antenna mast, installed on the right front cowl
All vehicles are equipped with an Ignition-Off side panel of the vehicle. The antenna mast is con-
Draw (IOD) fuse that is removed when the vehicle is nected to the center wire of the coaxial antenna
shipped from the factory. This fuse feeds various cable, and is not grounded to any part of the vehicle.
accessories that require battery current when the To eliminate static, the antenna base must have a
ignition switch is in the Off position, including the good ground. The antenna coaxial cable shield (the
clock and radio station preset memory functions. The
fuse is removed to prevent battery discharge during
vehicle storage.
8F - 2 AUDIO SYSTEMS TJ
outer wire mesh of the cable) is grounded to the • Radio receiver chassis ground wire or strap
antenna base and the radio chassis. • Engine-to-body ground strap
The antenna coaxial cable has an additional dis- • Engine-to-frame ground strap
connect, located behind the right end of the instru- • Resistor-type spark plugs
ment panel between the radio and the right cowl side • Radio suppression-type secondary ignition wir-
panel. This additional disconnect allows the instru- ing.
ment panel assembly to be removed and installed For more information on the spark plugs and sec-
without removing the radio. ondary ignition components, refer to Ignition Sys-
The factory-installed Electronically Tuned Radios tem in the Description and Operation section of
(ETRs) automatically compensate for radio antenna Group 8D - Ignition System.
trim. Therefore, no antenna trimmer adjustment is
required or possible when replacing the receiver or
the antenna. DIAGNOSIS AND TESTING
RADIO NOISE SUPPRESSION AUDIO SYSTEM
DESCRIPTION WARNING: ON VEHICLES EQUIPPED WITH AIR-

Radio Frequency Interference (RFI) and Electro- BAGS, REFER TO GROUP 8M - PASSIVE
Magnetic Interference (EMI) noise suppression is RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
accomplished primarily through circuitry internal to STEERING WHEEL, STEERING COLUMN, OR
the radio receivers. These internal suppression INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
devices are only serviced as part of the radio receiver. SERVICE. FAILURE TO TAKE THE PROPER PRE-
External suppression devices that are used on this CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
vehicle to control RFI or EMI noise include the fol- BAG DEPLOYMENT AND POSSIBLE PERSONAL
lowing: INJURY.
• Radio antenna base ground
Audio System Diagnosis

CONDITION POSSIBLE CAUSE CORRECTION
NO AUDIO. 1. Fuse faulty. 1. Check radio fuses in Power Distribution Center. Replace fuses,
if required.
2. Radio connector faulty. 2. Check for loose or corroded radio connector. Repair, if
required.
3. Wiring faulty. 3. Check for battery voltage at radio connector. Repair wiring, if
required.
4. Ground faulty. 4. Check for continuity between radio chassis and a known good
ground. There should be continuity. Repair ground, if required.
5. Radio faulty. 5. Exchange or replace radio, if required.
6. Speakers faulty. 6. See speaker diagnosis, in this group.
NO DISPLAY. 1. Fuse faulty. 1. Check radio fuses in Power Distribution Center. Replace fuses,
if required.
2. Radio connector faulty. 2. Check for loose or corroded radio connector. Repair, if
required.
required.
CLOCK WILL 1. Fuse faulty. 1. Check ignition-off draw fuse. Replace fuse, if required.
NOT KEEP SET 2. Radio connector faulty. 2. Check for loose or corroded radio connector. Repair, if
TIME. required.
required.
POOR RADIO 1. Antenna faulty. 1. See antenna diagnosis, in this group. Repair or replace
RECEPTION. antenna, if required.
NO/POOR TAPE 1. Faulty tape. 1. Insert known good tape and test operation.
OPERATION. 2. Foreign objects behind 2. Remove foreign objects and test operation.
tape door.
3. Dirty cassette tape 3. Clean head with Mopar Cassette Head Cleaner.
head.
4. Faulty tape deck. 4. Exchange or replace radio, if required.
NO COMPACT 1. Faulty CD. 1. Insert known good CD and test operation.
DISC 2. Foreign material on 2. Clean CD and test operation.
OPERATION CD.
3. Condensation on CD 3. Allow temperature of vehicle interior to stabilize and test
or optics. operation.
4. Faulty CD player. 4. Exchange or replace radio, if required.
RADIO
For circuit descriptions and diagrams, refer to
8W-47 - Audio System in Group 8W - Wiring Dia-
grams.
WARNING: ON VEHICLES EQUIPPED WITH AIR- CAUTION: The speaker output of the radio is a
BAGS, REFER TO GROUP 8M - PASSIVE “floating ground” system. Do not allow any speaker
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY lead to short to ground, as damage to the radio
STEERING WHEEL, STEERING COLUMN, OR may result.
SERVICE. FAILURE TO TAKE THE PROPER PRE- (1) Turn the ignition switch to the On position.
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- Turn the radio on. Adjust the balance and fader con-
BAG DEPLOYMENT AND POSSIBLE PERSONAL trols to check the performance of each individual
INJURY. speaker. Note the speaker locations that are not per-
forming correctly. Go to Step 2.
(2) Turn the radio off. Disconnect and isolate the
CAUTION: The speaker output of the radio is a battery negative cable. Remove the radio. Unplug the
“floating ground” system. Do not allow any speaker wire harness connectors at the radio. Check both the
lead to short to ground, as damage to the radio speaker feed (+) circuit and return (–) circuit cavities
may result. for the inoperative speaker location(s) at the radio
wire harness connectors for continuity to ground. In
(1) Check the fuse(s) in the Power Distribution each case, there should be no continuity. If OK, go to
Center (PDC). If OK, go to Step 2. If not OK, repair Step 4. If not OK, go to Step 3.
the shorted circuit or component as required and (3) Leave the radio wire harness connectors
replace the faulty fuse(s). unplugged. Unplug the wire harness connector at the
(2) Check for battery voltage at the fuse(s) in the inoperative speaker. Check both the speaker feed (+)
PDC. If OK, go to Step 3. If not OK, repair the open circuit and return (–) circuit cavities of the speaker
circuit to the battery and/or the ignition switch as wire harness connector for continuity to ground. In
required. each case, there should be no continuity. If OK,
(3) Disconnect and isolate the battery negative replace the shorted speaker. If not OK, repair the
cable. Remove the radio, but do not unplug the radio shorted circuit as required.
wire harness connectors. Check for continuity (4) Plug in the speaker wire harness connector.
between the radio chassis and a good ground. There Check the resistance between the speaker feed (+)
should be continuity. If OK, go to Step 4. If not OK, circuit and return (–) circuit cavities of the radio wire
repair the open radio chassis ground circuit as harness connectors for the inoperative speaker loca-
required. tion(s). The meter should read between 3 and 8 ohms
(4) Connect the battery negative cable. Turn the (speaker resistance). If OK, go to Step 5. If not OK,
ignition switch to the On position. Check for battery go to Step 6.
voltage at the fused ignition switch output (accesso- (5) Install a known good radio. Connect the bat-
ry/run) circuit cavity of the left (gray) radio wire har- tery negative cable. Turn the ignition switch to the
ness connector. If OK, go to Step 5. If not OK, repair On position. Turn on the radio and test the speaker
the open circuit as required. operation. If OK, replace the faulty radio. If not OK,
(5) Turn the ignition switch to the Off position. replace the faulty speaker.
Check for battery voltage at the fused B(+) circuit cav- (6) Turn the radio off. Turn the ignition switch to
ity of the left (gray) radio wire harness connector. If the Off position. Disconnect and isolate the battery
OK, replace the faulty radio. If not OK, repair the open negative cable. Remove the test radio. Unplug the
circuit to the Ignition-Off Draw (IOD) fuse as required. speaker wire harness connector at the inoperative
speaker. Check the resistance between the speaker
SPEAKER feed (+) circuit cavities of the radio wire harness con-
For circuit descriptions and diagrams, refer to nector and the speaker wire harness connector.
8W-47 - Audio System in Group 8W - Wiring Dia- Repeat the check between the speaker return (–) cir-
grams. cuit cavities of the radio wire harness connector and
the speaker wire harness connector. In each case,
there should be no measurable resistance. If OK,
replace the faulty speaker. If not OK, repair the
speaker wire harness circuit(s) as required.
INJURY.
ANTENNA (2) Connect one ohmmeter test lead to the tip of

the antenna mast. Connect the other test lead to the
WARNING: ON VEHICLES EQUIPPED WITH AIR- antenna base. Check for continuity.
BAGS, REFER TO GROUP 8M - PASSIVE (3) There should be no continuity. If continuity is
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY found, replace the faulty or damaged antenna base
STEERING WHEEL, STEERING COLUMN, OR and cable assembly.
SERVICE. FAILURE TO TAKE THE PROPER PRE- TEST 2
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- Test 2 checks the antenna for an open circuit as
BAG DEPLOYMENT AND POSSIBLE PERSONAL follows:
INJURY. (1) Unplug the antenna coaxial cable connector
from the radio chassis.
The following four tests are used to diagnose the (2) Connect one ohmmeter test lead to the tip of
antenna with an ohmmeter: the antenna mast. Connect the other test lead to the
• Test 1 - Mast to ground test center pin of the antenna coaxial cable connector.
• Test 2 - Tip-of-mast to tip-of-conductor test (3) Continuity should exist (the ohmmeter should
• Test 3 - Body ground to battery ground test only register a fraction of an ohm). High or infinite
• Test 4 - Body ground to coaxial shield test. resistance indicates damage to the base and cable
The ohmmeter test lead connections for each test assembly. Replace the faulty base and cable, if
are shown in Antenna Tests (Fig. 1). required.
NOTE: This model has a two-piece antenna coaxial TEST 3

cable. Tests 2 and 4 must be conducted in two Test 3 checks the condition of the vehicle body
steps to isolate a coaxial cable problem; from the ground connection. This test should be performed
coaxial cable connection under the right end of the with the battery positive cable removed from the bat-
instrument panel near the right cowl side inner tery. Disconnect both battery cables, the negative
panel to the antenna base, and then from the coax- cable first. Reconnect the battery negative cable and
ial cable connection to the radio chassis connec- perform the test as follows:
tion. (1) Connect one ohmmeter test lead to the vehicle
fender. Connect the other test lead to the battery
negative post.
(2) The resistance should be less than one ohm.
(3) If the resistance is more than one ohm, check
the braided ground strap connected to the engine and
the vehicle body for being loose, corroded, or dam-
aged. Repair the ground strap connection, if required.
TEST 4
Test 4 checks the condition of the ground between
the antenna base and the vehicle body as follows:
(1) Connect one ohmmeter test lead to the vehicle
fender. Connect the other test lead to the outer crimp
on the antenna coaxial cable connector.
(2) The resistance should be less then one ohm.
(3) If the resistance is more then one ohm, clean
and/or tighten the antenna base to fender mounting
hardware.
Fig. 1 Antenna Tests

TEST 1
Test 1 determines if the antenna mast is insulated
from the base. Proceed as follows:
(1) Unplug the antenna coaxial cable connector
from the radio chassis and isolate.
RADIO FREQUENCY INTERFERENCE • The antenna and cable must be carefully

matched to ensure a low Standing Wave Ratio
WARNING: ON VEHICLES EQUIPPED WITH AIR- (SWR).
BAGS, REFER TO GROUP 8M - PASSIVE Fleet vehicles are available with an extra-cost RFI-
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY suppressed Powertrain Control Module (PCM). This
STEERING WHEEL, STEERING COLUMN, OR unit reduces interference generated by the PCM on
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR some radio frequencies used in two-way radio com-
SERVICE. FAILURE TO TAKE THE PROPER PRE- munications. However, this unit will not resolve com-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- plaints of RFI in the commercial AM or FM radio
BAG DEPLOYMENT AND POSSIBLE PERSONAL frequency ranges.
INJURY.
For complete circuit diagrams, see Group 8W - REMOVAL AND INSTALLATION

Wiring Diagrams. Inspect the ground paths and con-
nections at the following locations: RADIO
• Blower motor
• Electric fuel pump WARNING: ON VEHICLES EQUIPPED WITH AIR-
• Engine-to-body ground strap BAGS, REFER TO GROUP 8M - PASSIVE
• Engine-to-frame ground strap RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
• Generator STEERING WHEEL, STEERING COLUMN, OR
• Ignition module INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
• Radio antenna base ground SERVICE. FAILURE TO TAKE THE PROPER PRE-
• Radio receiver chassis ground wire or strap CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
• Wiper motor. BAG DEPLOYMENT AND POSSIBLE PERSONAL
If the source of RFI or EMI noise is identified as a INJURY.
component on the vehicle (i.e., generator, blower
(1) Disconnect and isolate the battery negative cable.
motor, etc.), the ground path for that component
(2) Remove the instrument panel top cover from
should be checked. If excessive resistance is found in
the instrument panel. Refer to Instrument Panel Top
any ground circuit, clean, tighten, or repair the
Cover in Group 8E - Instrument Panel Systems for
ground circuits or connections to ground as required
the procedures.
before considering any component replacement.
(3) Remove the ash receiver from the ash receiver
For service and inspection of secondary ignition
housing in the lower instrument panel center bezel.
components, refer to the Diagnosis and Testing sec-
(4) Remove the one screw located in the back of
tion of Group 8D - Ignition Systems. Inspect the fol-
the ash receiver housing that secures the center
lowing secondary ignition system components:
bezel to the lower instrument panel (Fig. 2).
• Distributor cap and rotor
(5) Remove the two screws that secure the center
• Ignition coil
bezel to the top of the instrument panel.
• Spark plugs
(6) Using a trim stick or another suitable wide
• Spark plug wire routing and condition.
flat-bladed tool, gently pry the lower edge of the cen-
Reroute the spark plug wires or replace the faulty
ter bezel away from the instrument panel.
components as required.
(7) Lift the lower edge of the center bezel upwards
If the source of the RFI or EMI noise is identified
to release the four snap clip retainers that secure it
as two-way mobile radio or telephone equipment,
to the instrument panel.
check the equipment installation for the following:
• Power connections should be made directly to
panel.
the battery, and fused as closely to the battery as
(9) Remove the two screws that secure the radio to
possible.
the instrument panel (Fig. 3).
• The antenna should be mounted on the roof or
(10) Pull the radio out from the instrument panel
toward the rear of the vehicle. Remember that mag-
far enough to access the wire harness connectors and
netic antenna mounts on the roof panel can adversely
the antenna coaxial cable connector (Fig. 4).
affect the operation of an overhead console compass,
(11) Unplug the wire harness connectors and the
if the vehicle is so equipped.
antenna coaxial cable connector from the rear of the
• The antenna cable should be fully shielded coax-
radio.
ial cable, should be as short as is practical, and
(12) Remove the screw that secures the ground
should be routed away from the factory-installed
strap to the radio chassis.
vehicle wire harnesses whenever possible.
(13) Remove the radio from the instrument panel.
Fig. 4 Radio Connections - Typical

cable.
(2) Remove the two screws that secure the out-
board end of the speaker bezel to the instrument
panel (Fig. 5).
Fig. 2 Center Bezel Remove/Install
Fig. 3 Radio Remove/Install

Fig. 5 Instrument Panel Speaker Bezel Remove/
(14) Reverse the removal procedures to install. Install
Tighten the radio mounting screws to 5 N·m (45 in.
lbs.). Tighten the instrument panel center bezel (3) Using a trim stick or another suitable wide
mounting screws to 2.2 N·m (20 in. lbs.). flat-bladed tool, gently pry at the top and bottom
edges of the speaker bezel to release the two snap
SPEAKER clip retainers that secure the bezel to the instrument
panel.
INSTRUMENT PANEL (4) Remove the speaker bezel from the instrument
panel.
WARNING: ON VEHICLES EQUIPPED WITH AIR- (5) Remove the foam rubber speaker baffle from
BAGS, REFER TO GROUP 8M - PASSIVE RESTRAINT the speaker.
SYSTEMS BEFORE ATTEMPTING ANY STEERING (6) Remove the four screws that secure the
WHEEL, STEERING COLUMN, OR INSTRUMENT speaker to the instrument panel armature (Fig. 6).
PANEL COMPONENT DIAGNOSIS OR SERVICE. FAIL- (7) Pull the speaker away from the instrument
URE TO TAKE THE PROPER PRECAUTIONS COULD panel far enough to access the speaker wire harness
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT connector.
AND POSSIBLE PERSONAL INJURY.
(5) Lift the left outboard end flap of the sound bar
trim cover over the top of the sport bar far enough to
access the wire harness connector (Fig. 7).
Fig. 6 Instrument Panel Speaker Remove/Install

(8) Unplug the wire harness connector from the
speaker.
(9) Remove the speaker from the instrument Fig. 7 Sound Bar Wire Harness Connector Remove/
panel. Install
(10) Reverse the removal procedures to install. (6) Unplug the sound bar wire harness connector.
Tighten the speaker mounting screws to 1.1 N·m (10 (7) Lift each outboard end flap of the sound bar
in. lbs.). Tighten the speaker bezel mounting screws cover over the top of the sport bar far enough to
to 2.2 N·m (20 in. lbs.). access the mounting screws (Fig. 8).
SOUND BAR
cable.
(2) Remove the four screws that secure the
speaker grille and speaker to the sound bar.
(3) Lower the speaker and grille from the sound
bar far enough to access the speaker wire harness
connector.
speaker.
(5) Remove the speaker and grille from the sound
bar.
(6) Remove the speaker grille from the speaker.
(7) Reverse the removal procedures to install.
Tighten the mounting screws to 1.1 N·m (10 in. lbs.).
SOUND BAR Fig. 8 Sound Bar Remove/Install

(1) Disconnect and isolate the battery negative (8) Remove the two screws that secure each end of
cable. the sound bar to the sport bar.
(2) If the vehicle is equipped with the optional (9) Lift the sound bar up off of the sport bar to
hard top, remove the hard top from the vehicle. Refer remove it from the vehicle.
to Hard Top in Group 23 - Body for the procedures. (10) Reverse the removal procedures to install.
(3) If the vehicle is equipped with the standard Tighten the sound bar mounting screws to 11 N·m
soft top, lower the soft top. Refer to Folding Down (100 in. lbs.).
the Fabric Top in the Owner’s Manual for the proce-
dures.
(4) Release the hook and loop closure on each out-
board end flap of the sound bar trim cover.
ANTENNA (7) Remove the three screws that secure the

antenna body base to the right outer cowl side panel.
WARNING: ON VEHICLES EQUIPPED WITH AIR- (8) From the outside of the vehicle, pull the
BAGS, REFER TO GROUP 8M - PASSIVE antenna body base and cable assembly out through
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY the hole in the right outer cowl side panel.
STEERING WHEEL, STEERING COLUMN, OR (9) Reverse the removal procedures to install.
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR Tighten the antenna body base mounting screws to 2
SERVICE. FAILURE TO TAKE THE PROPER PRE- N·m (17 in. lbs.). Tighten the antenna mast to 3.3
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- N·m (30 in. lbs.).
INJURY. RADIO NOISE SUPPRESSION COMPONENTS
(1) Disconnect and isolate the battery negative WARNING: ON VEHICLES EQUIPPED WITH AIR-
cable. BAGS, REFER TO GROUP 8M - PASSIVE
(2) Remove the glove box from the instrument RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
panel. Refer to Glove Box in Group 8E - Instrument STEERING WHEEL, STEERING COLUMN, OR
Panel Systems for the procedures. INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
(3) Reach through the instrument panel glove box SERVICE. FAILURE TO TAKE THE PROPER PRE-
opening to unplug the antenna coaxial cable connec- CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
tor. Unplug the connector by pulling it apart while BAG DEPLOYMENT AND POSSIBLE PERSONAL
twisting the metal connector halves. Do not pull on INJURY.
the cable.
(4) From inside the passenger compartment, push
the coaxial cable grommet on the antenna body half REMOVAL
of the coaxial cable out through the hole in the right
inner cowl side panel (Fig. 9). ENGINE-TO-BODY GROUND STRAP
(1) Remove the screw that secures the engine-to-
body ground strap eyelet to the hood panel center
reinforcement (Fig. 10).
Fig. 9 Antenna Remove/Install Fig. 10 Engine-To-Body Ground Strap Remove/

Install
(5) Unscrew the antenna mast from the antenna
body base on the right outer cowl side panel. (2) Remove the screw that secures the engine-to-
(6) Using a trim stick or another suitable wide body ground strap eyelet to the dash panel.
flat-bladed tool, gently pry the edge of the antenna (3) Remove the nut that secures the engine-to-body
base trim cover to unsnap it from the antenna body ground strap eyelet to the stud on the left upper rear
base. corner of the engine cylinder head.
(4) Remove the engine-to-body ground strap eyelet
from the stud on the left upper rear corner of the
engine cylinder head.
(5) Remove the engine-to-body ground strap from
the engine compartment.
ENGINE-TO-FRAME GROUND STRAP

(1) Remove the nut that secures the engine-to-
frame ground strap eyelet to the forward ignition coil
mounting stud on the right side of the engine (Fig.
11) or (Fig. 12).
Fig. 12 Engine-To-Frame Ground Strap Remove/

Install - 4.0L Engine
engine-to-body ground strap eyelet to the stud on the
left upper rear corner of the engine cylinder head.
Tighten the nut to 5.6 N·m (50 in. lbs.).
engine-to-body ground strap eyelet to the dash panel.
Tighten the screw to 48.5 N·m (430 in. lbs.).
engine-to-body ground strap eyelet to the hood panel
Fig. 11 Engine-To-Frame Ground Strap Remove/ center reinforcement. Tighten the screw to 1.9 N·m
Install - 2.5L Engine (17 in. lbs.).
(2) Remove the engine-to-frame ground strap eye-
ENGINE-TO-FRAME GROUND STRAP
let from the forward ignition coil mounting stud on
the right side of the engine. (1) Position the engine-to-frame ground strap into
(3) Remove the screw that secures the engine-to- the engine compartment. The ground strap eyelet
frame ground strap eyelet to the top of the right with a 45 degree bend in it is to be mounted on the
frame rail. right frame rail.
(4) Remove the engine-to-frame ground strap from (2) Install and tighten the screw that secures the
the engine compartment. engine-to-frame ground strap eyelet to the top of the
right frame rail. Tighten the screw to 22.6 N·m (200
INSTALLATION in. lbs.).
(3) Install the engine-to-frame ground strap eyelet
ENGINE-TO-BODY GROUND STRAP over the forward ignition coil mounting stud on the
(1) Position the engine-to-body ground strap in the right side of the engine.
engine compartment. (4) Install and tighten the nut that secures the
(2) Position the engine-to-body ground strap eyelet engine-to-frame ground strap eyelet to the forward
over the stud on the left upper rear corner of the ignition coil mounting stud on the right side of the
engine cylinder head. engine. Tighten the nut to 22.6 N·m (200 in. lbs.).
TJ HORN SYSTEMS 8G - 1
HORN SYSTEMS
CONTENTS
page page
DESCRIPTION AND OPERATION HORN RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

HORN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 HORN SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . 3
HORN RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 REMOVAL AND INSTALLATION
HORN SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . 2 HORN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
HORN SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . 1 HORN RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
HORN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
DESCRIPTION AND OPERATION HORN

HORN SYSTEM DESCRIPTION
The dual electromagnetic diaphragm-type horns
DESCRIPTION are standard equipment on this model. Each horn is
A dual-note electric horn system is standard facto- secured with a bracket to the left front inner fender
ry-installed equipment on this model. The standard shield just ahead of the left front wheel house in the
equipment horn system features a one low-note horn engine compartment. The two horn brackets are
unit and one high-note horn unit. The horn system mounted in the same location, one on top of the
uses a non-switched source of battery current so that other. The high-note horn for the optional dual-note
the system will remain functional, regardless of the horn system is connected in parallel with and
ignition switch position. The horn system includes secured with a bracket just forward of the low-note
the following components: horn.
• Clockspring The two horns are connected in parallel. Each horn
• Horn(s) is grounded through its wire harness connector and
• Horn relay circuit to an eyelet secured to the engine compart-
• Horn switch ment side of the grille/headlamp mounting panel
Refer to Clockspring in the Description and Oper- near the left headlamp, and receives battery feed
ation section of Group 8M - Passive Restraint Sys- through the closed contacts of the horn relay.
tems for more information on this component. Refer The horns cannot be repaired or adjusted and, if
to Horn/Cigar Lighter in the Contents of Group 8W faulty or damaged, they must be individually
- Wiring Diagrams for complete circuit diagrams. Fol- replaced.
lowing are general descriptions of the remaining
major components in the horn system. OPERATION
Within the two halves of the molded plastic horn
OPERATION housing are a flexible diaphragm, a plunger, an elec-
The horn system is activated by a horn switch con- tromagnetic coil and a set of contact points. The dia-
cealed beneath the driver side airbag module trim phragm is secured in suspension around its
cover in the center of the steering wheel. Depressing perimeter by the mating surfaces of the horn hous-
the center of the driver side airbag module trim cover ing. The plunger is secured to the center of the dia-
closes the horn switch. Closing the horn switch acti- phragm and extends into the center of the
vates the horn relay. The activated horn relay then electromagnet. The contact points control the current
switches the battery current needed to energize the flow through the electromagnet.
horns. When the horn is energized, electrical current
Refer to the owner’s manual in the vehicle glove flows through the closed contact points to the electro-
box for more information on the features, use and magnet. The resulting electromagnetic field draws
operation of the horn system. the plunger and diaphragm toward it until that
movement mechanically opens the contact points.
When the contact points open, the electromagnetic
8G - 2 HORN SYSTEMS TJ
field collapses allowing the plunger and diaphragm to back side of the driver side airbag module trim cover
return to their relaxed positions and closing the con- in the center of the steering wheel (Fig. 1). The
tact points again. This cycle continues repeating at a switch consists of two plastic membranes, one that is
very rapid rate producing the vibration and move- flat and one that is slightly convex. These two mem-
ment of air that creates the sound that is directed branes are secured to each other around the perime-
through the horn outlet. ter. Inside the switch, the centers of the facing
surfaces of these membranes each has a grid made
HORN RELAY with an electrically conductive material applied to it.
One of the grids is connected to a circuit that pro-
DESCRIPTION vides it with continuity to ground at all times. The
The horn relay is a electromechanical device that grid of the other membrane is connected to the horn
switches battery current to the horn when the horn relay control circuit.
switch grounds the relay coil. The horn relay is
located in the Power Distribution Center (PDC) in
the engine compartment. If a problem is encountered
with a continuously sounding horn, it can usually be
quickly resolved by removing the horn relay from the
PDC until further diagnosis is completed. See the
fuse and relay layout label affixed to the inside sur-
face of the PDC cover for horn relay identification
and location.
The horn relay is a International Standards Orga-
nization (ISO) micro-relay. Relays conforming to the
ISO specifications have common physical dimensions,
current capacities, terminal patterns, and terminal
functions. The ISO micro-relay terminal functions
are the same as a conventional ISO relay. However,
the ISO micro-relay terminal pattern (or footprint) is
different, the current capacity is lower, and the phys-
ical dimensions are smaller than those of the conven-
tional ISO relay.
The horn relay cannot be repaired or adjusted and,
if faulty or damaged, it must be replaced.
OPERATION Fig. 1 Driver Side Airbag Module Trim Cover and

The ISO relay consists of an electromagnetic coil, a Horn Switch - Typical
resistor or diode, and three (two fixed and one mov-
able) electrical contacts. The movable (common feed) The steering wheel and steering column must be
relay contact is held against one of the fixed contacts properly grounded in order for the horn switch to
(normally closed) by spring pressure. When the elec- function properly. The horn switch is only serviced as
tromagnetic coil is energized, it draws the movable a part of the driver side airbag module trim cover. If
contact away from the normally closed fixed contact, the horn switch is damaged or faulty, or if the driver
and holds it against the other (normally open) fixed side airbag is deployed, the driver side airbag module
contact. trim cover and horn switch must be replaced as a
When the electromagnetic coil is de-energized, unit.
spring pressure returns the movable contact to the
normally closed position. The resistor or diode is con- OPERATION
nected in parallel with the electromagnetic coil in the When the center area of the driver side airbag trim
relay, and helps to dissipate voltage spikes that are cover is depressed, the electrically conductive grids
produced when the coil is de-energized. on the facing surfaces of the horn switch membranes
contact each other, closing the switch circuit. The
HORN SWITCH completed horn switch circuit provides a ground for
the control coil side of the horn relay, which activates
DESCRIPTION the relay. When the horn switch is released, the
A center-blow, normally open, resistive membrane- resistive tension of the convex membrane separates
type horn switch is secured with heat stakes to the the two electrically conductive grids and opens the
switch circuit.

HORN RELAY
The horn relay (Fig. 2) is located in the Power Dis-
tribution Center (PDC) behind the battery on the
driver side of the engine compartment. If a problem
is encountered with a continuously sounding horn, it
can usually be quickly resolved by removing the horn
relay from the PDC until further diagnosis is com-
pleted. See the fuse and relay layout label affixed to
the inside surface of the PDC cover for horn relay
identification and location. For complete circuit dia-
grams, refer to Horn/Cigar Lighter in the Contents
of Group 8W - Wiring Diagrams.

BAGS, REFER TO GROUP 8M - PASSIVE Fig. 2 Horn Relay
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY nector at all times. If OK, go to Step 4. If not OK,
STEERING WHEEL, STEERING COLUMN, OR repair the open circuit to the horn(s) as required.
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR (4) The coil battery terminal (86) is connected to
SERVICE. FAILURE TO TAKE THE PROPER PRE- the electromagnet in the relay. It is connected to bat-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- tery voltage and should be hot at all times. Check for
BAG DEPLOYMENT AND POSSIBLE PERSONAL battery voltage at the cavity for relay terminal 86. If
INJURY. OK, go to Step 5. If not OK, repair the open circuit to
the fuse in the PDC as required.
(1) Remove the horn relay from the PDC. Refer to
Horn Relay in the Removal and Installation section
the electromagnet in the relay. It is grounded
of this group for the procedures.
through the horn switch when the horn switch is
(2) A relay in the de-energized position should
depressed. Check for continuity to ground at the cav-
have continuity between terminals 87A and 30, and
ity for relay terminal 85. There should be continuity
no continuity between terminals 87 and 30. If OK, go
with the horn switch depressed, and no continuity
to Step 3. If not OK, replace the faulty relay.
with the horn switch released. If not OK, refer to
(3) Resistance between terminals 85 and 86 (elec-
Horn Switch in the Diagnosis and Testing section of
tromagnet) should be 75 6 5 ohms. If OK, go to Step
this group.
4. If not OK, replace the faulty relay.
(4) Connect a battery to terminals 85 and 86.
HORN SWITCH
There should now be continuity between terminals
For complete circuit diagrams, refer to Horn/Ci-
30 and 87, and no continuity between terminals 87A
and 30. If OK, perform the Relay Circuit Test that
Diagrams.
follows. If not OK, replace the faulty relay.
RELAY CIRCUIT TEST BAGS, REFER TO GROUP 8M - PASSIVE
(1) The relay common feed terminal cavity (30) is RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
connected to battery voltage and should be hot at all STEERING WHEEL, STEERING COLUMN, OR
times. If OK, go to Step 2. If not OK, repair the open INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
circuit to the fuse in the PDC as required. SERVICE. FAILURE TO TAKE THE PROPER PRE-
(2) The relay normally closed terminal (87A) is CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
connected to terminal 30 in the de-energized position, BAG DEPLOYMENT AND POSSIBLE PERSONAL
but is not used for this application. Go to Step 3. INJURY.
(3) The relay normally open terminal (87) is con-
nected to the common feed terminal (30) in the ener- (1) Disconnect and isolate the battery negative
gized position. This terminal supplies battery voltage cable. Remove the knee blocker from the instrument
to the horn(s). There should be continuity between panel.
the cavity for relay terminal 87 and the horn relay (2) Check for continuity between the metal steer-
output circuit cavity of each horn wire harness con- ing column jacket and a good ground. There should
be continuity. If OK, go to Step 3. If not OK, refer to
8G - 4 HORN SYSTEMS TJ
Steering Column in the Removal and Installation REMOVAL AND INSTALLATION
section of Group 19 - Steering for proper installation
of the steering column. HORN RELAY
(3) Remove the driver side airbag module from the
steering wheel. Disconnect the horn switch wire har- REMOVAL
ness connectors from the driver side airbag module. (1) Disconnect and isolate the battery negative
(4) Remove the horn relay from the Power Distri- cable.
bution Center (PDC). Check for continuity between (2) Remove the cover from the Power Distribution
the steering column half of the horn switch feed wire Center (PDC) (Fig. 3).
harness connector and a good ground. There should
be no continuity. If OK, go to Step 5. If not OK,
repair the shorted horn relay control circuit to the
horn relay in the PDC as required.
(5) Check for continuity between the steering col-
umn half of the horn switch feed wire harness con-
nector and the horn relay control circuit cavity for
the horn relay in the PDC. There should be continu-
ity. If OK, go to Step 6. If not OK, repair the open
horn relay control circuit to the horn relay in the
PDC as required.
(6) Check for continuity between the horn switch
feed wire and the horn switch ground wire on the
driver side airbag module. There should be no conti-
nuity. If OK, go to Step 7. If not OK, replace the
faulty horn switch.
(7) Depress the center of the driver side airbag
module trim cover and check for continuity between
the horn switch feed wire and the horn switch
ground wire on the driver side airbag module. There
should now be continuity. If not OK, replace the Fig. 3 Power Distribution Center
faulty horn switch. (3) See the fuse and relay layout label affixed to
the underside of the PDC cover for horn relay iden-
HORN tification and location.
For complete circuit descriptions, refer to Horn/Ci- (4) Remove the horn relay from the PDC.
Diagrams. INSTALLATION
(1) Disconnect the wire harness connectors from (1) See the fuse and relay layout label affixed to
the horn connector receptacles. Measure the resis- the underside of the PDC cover for the proper horn
tance between the ground circuit cavity of the horns relay location.
wire harness connectors and a good ground. There (2) Position the horn relay in the proper receptacle
should be no measurable resistance. If OK, go to Step in the PDC.
2. If not OK, repair the open ground circuit to ground (3) Align the horn relay terminals with the termi-
as required. nal cavities in the PDC receptacle.
(2) Check for battery voltage at the horn relay out- (4) Push down firmly on the horn relay until the
put circuit cavity of the horns wire harness connec- terminals are fully seated in the terminal cavities in
tors. There should be zero volts. If OK, go to Step 3. the PDC receptacle.
If not OK, repair the shorted horn relay output cir- (5) Install the cover onto the PDC.
cuit or replace the faulty horn relay as required. (6) Reconnect the battery negative cable.
(3) Depress the horn switch. There should now be
battery voltage at the horn relay output circuit cavity
of the horns wire harness connectors. If OK, replace
the faulty horns. If not OK, repair the open horn
relay output circuit to the horn relay as required.
HORN
REMOVAL
cable.
(2) Disconnect the wire harness connectors from
the horn connector receptacles (Fig. 4).
(3) Remove the two screws that secure the horn
and mounting bracket units to the left front inner
fender shield.
(4) Remove the horn and mounting bracket units
from the left front inner fender shield.
INSTALLATION
(1) Position the horn and mounting bracket units
onto the left front inner fender shield.
horn and mounting bracket units to the left front
inner fender shield. Tighten the screw to 6.8 N·m (5
ft. lbs.).
(3) Reconnect the wire harness connectors to the
horn connector receptacles.
Fig. 4 Horns Remove/Install

TJ SPEED CONTROL SYSTEM 8H - 1
SPEED CONTROL SYSTEM

CONTENTS
page page
DESCRIPTION AND OPERATION ROAD TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

POWERTRAIN CONTROL MODULE . . . . . . . . . . 2 SPEED CONTROL SERVO . . . . . . . . . . . . . . . . . . 3
SERVO CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SPEED CONTROL SWITCHES . . . . . . . . . . . . . . 2
SPEED CONTROL SERVO . . . . . . . . . . . . . . . . . . 1 STOP LAMP SWITCH . . . . . . . . . . . . . . . . . . . . . 2
SPEED CONTROL SOLENOID CIRCUITS . . . . . . 1 VACUUM SUPPLY TEST . . . . . . . . . . . . . . . . . . . 3
SPEED CONTROL SWITCHES . . . . . . . . . . . . . . 1 VEHICLE SPEED SIGNAL . . . . . . . . . . . . . . . . . . 2
STOP LAMP SWITCH . . . . . . . . . . . . . . . . . . . . . 1 REMOVAL AND INSTALLATION
VACUUM RESERVOIR . . . . . . . . . . . . . . . . . . . . 2 SERVO CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . 5
VEHICLE SPEED SENSOR . . . . . . . . . . . . . . . . . 2 SPEED CONTROL SERVO . . . . . . . . . . . . . . . . . . 4
DIAGNOSIS AND TESTING SPEED CONTROL SWITCH . . . . . . . . . . . . . . . . . 4
ON-BOARD DIAGNOSTIC TEST FOR SPEED STOP LAMP SWITCH . . . . . . . . . . . . . . . . . . . . . 5
CONTROL SYSTEM . . . . . . . . . . . . . . . . . . . . . 2 VACUUM RESERVOIR . . . . . . . . . . . . . . . . . . . . 6
OVERSHOOT/UNDERSHOOT FOLLOWING SPECIFICATIONS
SPEED CONTROL SET . . . . . . . . . . . . . . . . . . . 3 TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . 6
DESCRIPTION AND OPERATION are used. The outputs from these switches are fil-
tered into one input. The Powertrain Control Module
SPEED CONTROL SERVO (PCM) determines which output has been applied
The servo unit consists of a solenoid valve body, a through resistive multiplexing. The input circuit
vacuum servo and the mounting bracket. The Power- voltage is measured by the PCM to determine which
train Control Module (PCM) controls the solenoid switch function has been selected.
valve body. The solenoid valve body controls the A speed control indicator lamp, located on the
application and release of vacuum to the diaphragm instrument panel cluster is energized by the PCM via
of the vacuum servo. A cable connects the servo with the CCD Bus. This occurs when speed control system
the throttle linkage. The servo unit cannot be power has been turned ON, and the engine is run-
repaired and is serviced only as a complete assembly. ning.
The two switch modules are labeled: ON/OFF, SET,
SPEED CONTROL SOLENOID CIRCUITS RESUME/ACCEL, CANCEL and COAST. Refer to
the owner’s manual for more information on speed
When all of the speed control parameters are met,
control switch functions and setting procedures. The
and the SET button is pressed, the PCM actuates the
individual switches cannot be repaired. If one indi-
vent solenoid and “duty-cycles” the vacuum solenoid
vidual switch fails, the switch module must be
to open the throttle and bring the vehicle up to tar-
replaced.
get speed. When the vehicle is at target speed, it will
actuate the vent solenoid with the vacuum solenoid
de-activated to maintain the vehicle at target speed. STOP LAMP SWITCH
When the vehicle is above target speed, the PCM will Vehicles equipped with the speed control option use
“duty-cycle” the vent solenoid with the vacuum sole- a dual function stop lamp switch. The switch is
noid still de-activated to close the throttle to return mounted on the brake pedal mounting bracket under
to target speed. the instrument panel. The PCM monitors the state of
the dual function stop lamp switch. Refer to the
SPEED CONTROL SWITCHES Brake section for more information on stop lamp
Two separate speed control switch modules are switch service and adjustment procedures.
mounted on the steering wheel to the left and right
side of the driver’s airbag module. Within the two SERVO CABLE
switch modules, five momentary contact switches, The speed control servo cable is connected between
supporting seven different speed control functions the speed control vacuum servo diaphragm and the
throttle body control linkage. This cable causes the
8H - 2 SPEED CONTROL SYSTEM TJ
throttle control linkage to open or close the throttle • A Diagnostic Trouble Code (DTC). If a DTC
valve in response to movement of the vacuum servo exists, conduct tests per the Powertrain Diagnostic
diaphragm. Procedures service manual.
• A misadjusted brake (stop) lamp switch. This
POWERTRAIN CONTROL MODULE could also cause an intermittent problem.
The speed control electronic control circuitry is • Loose, damaged or corroded electrical connec-
integrated into the Powertrain Control Module tions at the servo. Corrosion should be removed from
(PCM). The PCM is located in the engine compart- electrical terminals and a light coating of Mopar
ment. The PCM speed control functions are moni- MultiPurpose Grease, or equivalent, applied.
tored by the On-Board Diagnostics (OBD). All OBD- • Leaking vacuum reservoir.
sensed systems are monitored by the PCM. Each • Loose or leaking vacuum hoses or connections.
monitored circuit is assigned a Diagnostic Trouble • Defective one-way vacuum check valve.
Code (DTC). The PCM will store a DTC in electronic • Secure attachment of both ends of the speed con-
memory for certain failures it detects. See On-Board trol servo cable.
Diagnostic Test For Speed Control System in this • Smooth operation of throttle linkage and throttle
group for more information. The PCM cannot be body air valve.
repaired and must be replaced if faulty. • Failed speed control servo. Do the servo vacuum
test.
VACUUM RESERVOIR
A vacuum reservoir is used to supply the vacuum CAUTION: When test probing for voltage or conti-
needed to maintain proper speed control operation nuity at electrical connectors, care must be taken
when engine vacuum drops, such as in climbing a not to damage connector, terminals or seals. If
grade while driving. A one-way check valve is used in these components are damaged, intermittent or
the vacuum line between the reservoir and the vac- complete system failure may occur.
uum source. This check valve is used to trap engine
vacuum in the reservoir. On certain vehicle applica-
tions, this reservoir is shared with the heating/air-
ON-BOARD DIAGNOSTIC TEST FOR SPEED
conditioning system. The vacuum reservoir cannot be CONTROL SYSTEM
repaired and must be replaced if faulty. The Powertrain Control Module (PCM) monitors
critical input and output circuits of the speed control
VEHICLE SPEED SENSOR system, making sure they are operational. A Diagnos-
The Vehicle Speed Sensor (VSS) is a pulse genera- tic Trouble Code (DTC) is assigned to each input and
tor mounted to an adapter near the transmission out- output circuit monitored by the On-Board Diagnostic
put shaft. The sensor is driven through the adapter (OBD) system. Some circuits are checked continu-
by a speedometer pinion gear. The VSS pulse signal ously and some are checked only under certain con-
to the speedometer/odometer is monitored by the ditions.
PCM speed control circuitry to determine vehicle For DTC information, refer to Diagnostic Trouble
speed and to maintain speed control set speed. Codes in Group 25, Emission Control System. This
will include a complete list of DTC’s including DTC’s
for the speed control system.
VEHICLE SPEED SIGNAL
ROAD TEST For diagnosis and testing of the Vehicle Speed Sig-
Perform a vehicle road test to verify reports of nal (VSS), refer to the appropriate Powertrain Diag-
speed control system malfunction. The road test nostic Procedures service manual. Also refer to the
should include attention to the speedometer. Speed- DRB scan tool.
ometer operation should be smooth and without flut-
ter at all speeds. SPEED CONTROL SWITCHES
Flutter in the speedometer indicates a problem To perform a complete test of the speed control
which might cause surging in the speed control sys- switch circuits, refer to the appropriate Powertrain
tem. The cause of any speedometer problems should Diagnostic Procedures manual.
be corrected before proceeding. Refer to Group 8E,
Instrument Panel and Gauges for speedometer diag- STOP LAMP SWITCH
nosis. For continuity checks and switch adjustment, refer
If a road test verifies a system problem and the to Group 5, Brakes.
speedometer operates properly, check for:
VACUUM SUPPLY TEST stop lamp switch. Also check stop lamp switch
(1) Disconnect vacuum hose at speed control servo adjustment. Refer to Group 5, Brakes for procedures.
and install a vacuum gauge into the disconnected (5) Connect a small gauge jumper wire between
hose. the disconnected servo harness 4–way connector
(2) Start engine and observe gauge at idle. Vac- pin–3, and pin–3 on the servo. Check for battery volt-
uum gauge should read at least ten inches of mer- age at pins–1, 2 and 4 of the servo. If battery voltage
cury. is not at these pins, replace the servo.
(3) If vacuum is less than ten inches of mercury,
determine source of leak. Check vacuum line to
engine for leaks. Also check actual engine intake
manifold vacuum. If manifold vacuum does not meet
this requirement, check for poor engine performance
and repair as necessary.
(4) If vacuum line to engine is not leaking, check
for leak at vacuum reservoir. To locate and gain
access to reservoir, refer to Vacuum Reservoir Remov-
al/Installation in this group. Disconnect vacuum line
at reservoir and connect a hand-operated vacuum
pump to reservoir fitting. Apply vacuum. Reservoir
vacuum should not bleed off. If vacuum is being lost,
replace reservoir.
(5) Verify operation of one-way check valve and
check it for leaks.
(a) Locate one-way check valve. The valve is
located in vacuum line between vacuum reservoir
and engine vacuum source. Disconnect vacuum
hoses (lines) at each end of valve. Fig. 1 Servo 4–Way Harness Connector
(b) Connect a hand-operated vacuum pump to
(6) Turn ignition switch to OFF position. Check for
reservoir end of check valve. Apply vacuum. Vac-
continuity between disconnected servo harness
uum should not bleed off. If vacuum is being lost,
4–way connector pin–4 and a good ground. There
replace one-way check valve.
should be continuity. If not OK, repair open circuit to
(c) Connect a hand-operated vacuum pump to
ground as required.
vacuum source end of check valve. Apply vacuum.
Vacuum should flow through valve. If vacuum is
not flowing, replace one-way check valve. Seal the
OVERSHOOT/UNDERSHOOT FOLLOWING
fitting at opposite end of valve with a finger and SPEED CONTROL SET
apply vacuum. If vacuum will not hold, diaphragm If the operator repeatedly presses and releases the
within check valve has ruptured. Replace valve. set button with their foot off of the accelerator (a “lift
foot set” to begin speed control operation), the vehicle
SPEED CONTROL SERVO may accelerate and exceed the desired set speed by
For complete speed control system diagnosis, refer up to 5 MPH (8 km/h) and then decelerate to less
to the appropriate Powertrain Diagnostic Procedures than the desired set speed before finally achieving
manual. To test the speed control servo only, refer to the desired set speed.
the following: The Speed Control has an adaptive strategy that
The engine must be started and running for the compensates for vehicle-to-vehicle variations in speed
following voltage tests. control cable lengths. When the speed control is set
(1) Start engine. with the vehicle operators foot off of the accelerator
(2) Disconnect 4–way electrical connector at servo. pedal, the speed control thinks there is excessive
(3) Turn speed control switch to ON position. speed control cable slack and adapts. If the lift foot
(4) Check for battery voltage at pin–3 of wiring sets are continually used, the speed control over-
harness 4–way connector (Fig. 1). This is the 12 volt shoot/undershoot condition will develop.
feed from the stoplamp switch. When the brake pedal To “unlearn” the overshoot/undershoot condition,
is depressed, voltage should not be present at pin–3. the vehicle operator has to press and release the set
If voltage is not present with brake pedal not button while maintaining the desired set speed with
depressed, check for continuity between servo and the accelerator pedal (not decelerating or accelerat-
ing), and then turn the cruise control switch to the
OFF position (or press the CANCEL button if
equipped) after waiting 10 seconds. This procedure
must be performed approximately 10–15 times to
completely unlearn the overshoot/undershoot condi-
tion.

SPEED CONTROL SERVO
REMOVAL
(2) Disconnect vacuum line at servo (Fig. 2).
(3) Disconnect electrical connector at servo.
(4) Disconnect servo cable at throttle body. Refer to
Servo Cable Removal/Installation in this group. Fig. 3 Servo Cable Clip Remove/Install—Typical
(5) Remove 2 mounting nuts holding servo cable
sleeve to bracket (Fig. 2) or (Fig. 3). (5) Connect vacuum line at servo.
(6) Pull speed control cable sleeve and servo away (6) Connect electrical connector at servo.
from servo mounting bracket to expose cable retain- (7) Connect servo cable to throttle body. Refer to
ing clip (Fig. 3) and remove clip. Note: The servo Servo Cable Removal/Installation in this group.
mounting bracket displayed in (Fig. 3) is a typical (8) Connect negative battery cable to battery.
bracket and may/may not be applicable to this model (9) Before starting engine, operate accelerator
vehicle. pedal to check for any binding.
SPEED CONTROL SWITCH

WARNING: BEFORE ATTEMPTING TO DIAGNOSE,
REMOVE OR INSTALL ANY AIRBAG SYSTEM OR
RELATED STEERING WHEEL AND STEERING COL-
UMN COMPONENTS YOU MUST FIRST DISCON-
NECT AND ISOLATE THE BATTERY NEGATIVE
(GROUND) CABLE. WAIT 2 MINUTES FOR SYSTEM
CAPACITOR TO DISCHARGE BEFORE FURTHER
SYSTEM SERVICE. FAILURE TO DO SO COULD
RESULT IN ACCIDENTAL DEPLOYMENT AND POS-
SIBLE PERSONAL INJURY.
REMOVAL
(1) Disconnect and isolate negative battery cable
from battery.
(2) Remove airbag module. Refer to Group 8M,
Passive Restraint Systems for procedures.
Fig. 2 Speed Control Servo Location (3) From underside of steering wheel, remove
(7) Remove servo from mounting bracket. While speed control switch mounting screw (Fig. 4).
removing, note orientation of servo to bracket. (4) Remove switch from steering wheel and unplug
electrical connector.
INSTALLATION
(1) Position servo to mounting bracket. INSTALLATION
(2) Align hole in cable connector with hole in servo (1) Plug electrical connector into switch.
pin. Install cable-to-servo retaining clip. (2) Position switch to steering wheel.
(3) Insert servo mounting studs through holes in (3) Install switch mounting screw and tighten to
servo mounting bracket. 1.5 N·m (14 in. lbs.) torque.
(4) Install servo mounting nuts and tighten to 8.5 (4) Install airbag module. Refer to Group 8M, Pas-
N·m (75 in. lbs.). sive Restraint Systems for procedures.
Fig. 4 Speed Control Switch Remove/Install

(5) Connect negative battery cable to battery.
STOP LAMP SWITCH

Refer to Stop Lamp Switch in Group 5, Brakes for
removal/installation and adjustment procedures.
SERVO CABLE
REMOVAL Fig. 5 Servo Cable to Bellcrank—Remove/Install
(2) Using finger pressure only, remove cable con-
nector by pushing connector off the throttle body
bellcrank pin (Fig. 5). DO NOT try to pull cable
connector off perpendicular to the bellcrank
pin. Connector will be broken.
(3) Two squeeze tabs are located on sides of speed
control cable at cable locking plate (Fig. 6). Squeeze
the tabs together and push cable out of cable locking
plate.
(4) Unclip cable from cable guide at valve cover
(Fig. 6).
(5) Disconnect servo cable at servo. Refer to Speed
Control Servo—Removal/Installation.
INSTALLATION
(1) Attach end of cable to speed control servo.
Refer to Speed Control Servo Removal/Installation.
(2) Install cable into cable locking plate (snaps in).
(3) Install cable connector at throttle body
bellcrank pin (snaps on).
(4) Clip cable to cable guide at valve cover.
(5) Connect negative battery cable to battery. Fig. 6 Squeeze Tabs at Cable Locking Plate
(6) Before starting engine, operate accelerator
pedal to check for any binding.
VACUUM RESERVOIR REMOVAL

The vacuum reservoir is located under the vehicle (1) Remove battery and battery tray. Refer to
battery tray (Fig. 7). Group 8A, Battery for procedure.
(2) Disconnect vacuum supply line at reservoir
(Fig. 7).
(3) Remove screw securing reservoir to inner
fender.
(4) Remove reservoir from vehicle.
INSTALLATION
(1) Position reservoir to vehicle and install mount-
ing screw.
(2) Tighten screw to 1.2 N·m (10 in. lbs.) torque.
(3) Connect vacuum line to reservoir.
(4) Install battery and battery tray. Refer to Group
8A, Battery.
Fig. 7 Vacuum Reservoir Removal/Installation
SPECIFICATIONS
TORQUE CHART
Description Torque
Servo Mounting Bracket-to-Servo
Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 N·m
(75 in. lbs.)
Speed Control Switch Mounting
Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 N·m
(14 in. lbs.)
Vacuum Reservoir Mounting
Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 N·m
(10 in. lbs.)
TJ TURN SIGNAL AND HAZARD WARNING SYSTEMS 8J - 1
TURN SIGNAL AND HAZARD WARNING SYSTEMS

CONTENTS
page page
DESCRIPTION AND OPERATION DIAGNOSIS AND TESTING

COMBINATION FLASHER . . . . . . . . . . . . . . . . . . 3 TURN SIGNAL AND HAZARD WARNING
HAZARD WARNING SYSTEM . . . . . . . . . . . . . . . 1 SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TURN SIGNAL CANCELLING CAM . . . . . . . . . . . 2 TURN SIGNAL SWITCH AND HAZARD
TURN SIGNAL SWITCH AND HAZARD WARNING SWITCH . . . . . . . . . . . . . . . . . . . . . 5
WARNING SWITCH . . . . . . . . . . . . . . . . . . . . . 2 REMOVAL AND INSTALLATION
TURN SIGNAL SYSTEM . . . . . . . . . . . . . . . . . . . 1 COMBINATION FLASHER . . . . . . . . . . . . . . . . . . 5
TURN SIGNAL SWITCH AND HAZARD
WARNING SWITCH . . . . . . . . . . . . . . . . . . . . . 6
DESCRIPTION AND OPERATION and off. If the exterior lamps are turned off, the front
park/turn signal lamp and the front side marker
TURN SIGNAL SYSTEM lamp will flash in unison. If the exterior lamps are
turned on, the front park/turn signal lamp and the
DESCRIPTION front side marker lamp will flash alternately.
A turn signal system is standard factory-installed See the owner’s manual in the vehicle glove box for
safety equipment on this model. The turn signal sys- more information on the features, use and operation
tem uses ignition switched battery current, and will of the turn signal system.
operate only when the ignition switch is in the On or
Accessory positions. The turn signal system includes HAZARD WARNING SYSTEM
the following components:
• Combination flasher DESCRIPTION
• Front side marker lamps A hazard warning system is standard factory-in-
• Turn signal cancelling cam stalled safety equipment on this model. Unlike the
• Turn signal indicator lamps turn signal system, the hazard warning system uses
• Turn signal lamps a non-switched source of battery current so that the
• Turn signal switch. system will operate regardless of the ignition switch
Refer to Lamp in the proper section of Group 8L - position. The hazard warning system includes the fol-
Lamps for more information on the exterior turn sig- lowing components:
nal lamps. Refer to Instrument Cluster in the • Combination flasher
proper section of Group 8E - Instrument Panel Sys- • Front side marker lamps
tems for more information on the turn signal indica- • Hazard warning switch
tor lamps. Following are general descriptions of the • Turn signal indicator lamps
major components in the turn signal system. For • Turn signal lamps.
complete circuit diagrams, refer to Turn Signals in Refer to Lamp in the proper section of Group 8L -
the Contents of Group 8W - Wiring Diagrams. Lamps for more information on the exterior turn sig-
nal lamps. Refer to Instrument Cluster in the
OPERATION proper section of Group 8E - Instrument Panel Sys-
With the ignition switch in the On or Accessory tems for more information on the turn signal indica-
position, and the turn signal (multi-function) switch tor lamps. Following are general descriptions of the
control stalk moved up (right turn) or down (left major components in the hazard warning system. For
turn), the turn signal system is activated. When the complete circuit diagrams, refer to Turn Signals in
turn signal system is activated, the circuitry of the the Contents of Group 8W - Wiring Diagrams.
turn signal switch and the combination flasher will
cause the selected (right or left) turn signal indicator OPERATION
lamp, front park/turn signal lamp, front side marker With the hazard warning switch in the On posi-
lamp and rear tail/stop/turn signal lamp to flash on tion, the hazard warning system is activated. When
8J - 2 TURN SIGNAL AND HAZARD WARNING SYSTEMS TJ
the hazard warning system is activated, the circuitry The information contained in this group addresses
of the hazard warning switch and the combination only the multi-function switch turn signal and haz-
flasher will cause both the right side and the left side ard warning functions. For information relative to
turn signal indicator lamps, front park/turn signal the other systems that are controlled by and circuits
lamps, front side marker lamps and rear tail/stop/ that are integral to the multi-function switch, see the
turn signal lamps to flash on and off. If the exterior group in this service manual that covers that system.
lamps are turned off, the front park/turn signal However, the turn signal and hazard warning
lamps and the front side marker lamps will flash in switches cannot be repaired. If these switches or any
unison. If the exterior lamps are turned on, the front other circuit or component of the multi-function
park/turn signal lamps and the front side marker switch unit is faulty or damaged, the entire multi-
lamps will flash alternately. function switch unit must be replaced.
See the owner’s manual in the vehicle glove box for
more information on the features, use and operation OPERATION
of the hazard warning system.
TURN SIGNAL SWITCH
TURN SIGNAL SWITCH AND HAZARD The multi-function switch control stalk that
WARNING SWITCH extends from the left side of the steering column just
below the steering wheel is moved up or down to
DESCRIPTION activate the turn signal switch. When the control
The turn signal and hazard warning switches are stalk is moved in the upward direction, the right
integral to the multi-function switch unit, which is turn signal switch circuitry is activated; and, when
secured to the left side of the steering column (Fig. the control stalk is moved in the downward direction,
1). The only visible parts of the multi-function switch the left turn signal switch circuitry is activated. The
are the control stalk that extends from the left side turn signal switch has a detent position in each
of the steering column, and the hazard warning direction that provides turn signals with automatic
switch button that protrudes from the top of the cancellation, and an intermediate momentary posi-
steering column. The multi-function switch control tion in each direction that provides turn signals only
stalk has international control symbols on it, which until the multi-function switch control stalk is
identify its functions. The hazard warning switch released.
button is identified with a double triangle, which is When the turn signal switch is in a detent posi-
the international control symbol for hazard warning. tion, it is turned off by one of two turn signal cancel-
The remainder of the multi-function switch is con- ling cam lobes that are integral to the rotor of the
cealed beneath the steering column shrouds. clockspring mechanism. Turning the steering wheel
The multi-function switch also contains circuitry causes the turn signal cancelling cam lobes to contact
for the following functions: a cancel actuator in the multi-function switch, and
• Headlamp beam selection the turn signal switch automatically returns to the
• Headlamp optical horn off position.
HAZARD WARNING SWITCH

The hazard warning switch is controlled by the
hazard warning switch button. Slide the switch but-
ton to the left to turn the switch on and activate the
hazard warning system, and slide the button to the
right again to turn the switch and the hazard warn-
ing system off.
TURN SIGNAL CANCELLING CAM

DESCRIPTION
The turn signal cancelling cam is concealed within
the steering column below the steering wheel. The
turn signal cancelling cam consists of two lobes that
are integral to the lower surface of the clockspring
rotor. The clockspring mechanism provides turn sig-
Fig. 1 Multi-Function Switch nal cancellation as well as a constant electrical con-
nection between the horn switch, driver side airbag
module and speed control switches on the steering combination flasher with a known good unit to con-
wheel and the instrument panel wire harness on the firm system operation.
steering column. The housing of the clockspring is The combination flasher has five blade-type termi-
secured to the steering column and remains station- nals intended for the following inputs and outputs:
ary. The rotor of the clockspring, including the turn fused B(+), fused ignition switch output, ground, turn
signal cancelling cam lobes rotate with the steering signal circuit, and hazard warning circuit. Constant
wheel. battery voltage and ground are supplied to the
The turn signal cancelling cam is integral to the flasher so that it can perform the hazard warning
clockspring and cannot be repaired. If faulty or dam- function, and ignition switched battery voltage is
aged, the entire clockspring assembly must be supplied for the turn signal function. Refer to Turn
replaced. Refer to Clockspring in the Removal and Signals in the Contents of Group 8W - Wiring Dia-
Installation section of Group 8M - Passive Restraint grams for complete circuit diagrams.
Systems for the clockspring service procedures. The combination flasher is located in a bracket
secured with a screw to the underside of the upper
OPERATION steering column support bracket, to the right of the
The turn signal cancelling cam has two lobes steering column under the instrument panel. The
molded into the lower surface of the clockspring combination flasher cannot be repaired or adjusted
rotor. When the turn signals are activated by moving and, if faulty or damaged, it must be replaced.
the multi-function switch control stalk to a detent
position, a turn signal cancel actuator is extended OPERATION
from the inside surface of the multi-function switch The IC within the combination flasher (Fig. 2) con-
housing toward the clockspring rotor. When the tains the logic that controls the flasher operation and
steering wheel is rotated during the turn, one of the the flash rate. Pin 6 of the IC receives a sense volt-
two turn signal cancelling cam lobes will contact the age from the hazard warning circuit of the multi-
turn signal cancel actuator, releasing the multi-func- function switch. When the hazard warning switch is
tion switch control stalk from its detent and cancel- turned on, the 9hazard on sense9 voltage will become
ling the turn signal event. low due to the circuit being grounded through the
turn signal bulbs. This low voltage sense signals the
COMBINATION FLASHER IC to energize the flash control Positive-Negative-
Positive (PNP) transistor at a pre-calibrated flash
DESCRIPTION rate or frequency. Each time the PNP transistor ener-
The combination flasher is a smart relay that func- gizes the hazard warning circuit, the pin 6 9hazard
tions as both the turn signal system and the hazard on sense9 voltage will become high and the IC signals
warning system flasher. The combination flasher con- the PNP transistor to de-energize the circuit. This
tains active electronic Integrated Circuitry (IC) ele- cycling will continue until the hazard warning switch
ments. This flasher is designed to handle the current is turned off.
flow requirements of the factory-installed lighting. If
supplemental lighting is added to the turn signal
lamp circuits, such as when towing a trailer with
lights, the combination flasher will automatically try
to compensate to keep the flash rate the same.
While the combination flasher has a International
Standards Organization (ISO)-type relay terminal
configuration or footprint, the internal circuitry is
much different. The combination flasher does not use
standard ISO-relay inputs or provide ISO-relay type
outputs or functions. The combination flasher should
never be substituted for an ISO-relay or replaced
with an ISO-relay, or else component and vehicle
damage may occur.
Because of the active electronic elements within
the combination flasher, it cannot be tested with con-
ventional automotive electrical test equipment. If the
combination flasher is believed to be faulty, test the
turn signal system and hazard warning system cir-
cuits as described in this group. Then replace the Fig. 2 Combination Flasher - Typical
Likewise, pin 8 of the IC receives a sense voltage WARNING: ON VEHICLES EQUIPPED WITH AIR-
from the turn signal circuits of the multi-function BAGS, REFER TO GROUP 8M - PASSIVE
switch. When the left or right turn signal switch is RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
turned on, the 9turn signal on sense9 voltage will STEERING WHEEL, STEERING COLUMN, OR
become low due to the circuit being grounded INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
through the turn signal bulbs. This low voltage sense SERVICE. FAILURE TO TAKE THE PROPER PRE-
signals the IC to energize the flash control PNP tran- CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
sistor at a pre-calibrated flash rate or frequency. BAG DEPLOYMENT AND POSSIBLE PERSONAL
Each time the PNP transistor energizes the turn sig- INJURY.
nal circuit, the pin 8 9turn signal on sense9 voltage
will become high and the IC signals the PNP transis- (1) Turn the ignition switch to the On position.
tor to de-energize the circuit. This cycling will con- Actuate the turn signal switch or the hazard warning
tinue until the right or left turn signal switch is switch. Observe the turn signal indicator lamp(s) in
turned off. the instrument cluster. If the flash rate is very high,
A special design feature of the combination flasher check for a turn signal bulb that is not lit or is very
allows it to 9sense9 that a turn signal circuit or bulb dimly lit. Repair the circuits to that lamp or replace
is not operating, and provide the driver an indication the faulty bulb, as required. If the turn signal indi-
of the condition by flashing the remaining bulbs in cator(s) fail to light, go to Step 2.
the affected circuit at a higher rate (120 flashes-per- (2) Turn the ignition switch to the Off position.
minute or higher). Conventional flashers either con- Check the turn signal fuse in the fuseblock module
tinue flashing at their typical rate (heavy-duty type), and/or the hazard warning fuse in the Power Distri-
or discontinue flashing the affected circuit entirely bution Center (PDC). If OK, go to Step 3. If not OK,
(standard-duty type). During turn signal operation, repair the shorted circuit or component as required
the combination flasher IC compares normal battery and replace the faulty fuse(s).
voltage input on pin 2 with the shunt resistor voltage (3) Check for battery voltage at the hazard warn-
input on pin 7. If the IC 9senses9 that the voltage dif- ing fuse in the PDC. If OK, go to Step 4. If not OK,
ference between pin 2 and pin 7 is different than the repair the open fused B(+) circuit to the battery as
pre-calibrated value of the IC, it will increase the required.
rate at which it signals the PNP transistor to ener- (4) Turn the ignition switch to the On position.
gize the pin 1 output. Thus, the inoperative half (left Check for battery voltage at the turn signal fuse in
or right side) of the turn signal circuit will flash the fuseblock module. If OK, go to Step 5. If not OK,
faster. repair the open fused ignition switch output (accesso-
ry/run) circuit to the ignition switch as required.
(5) Turn the ignition switch to the Off position.
DIAGNOSIS AND TESTING Disconnect and isolate the battery negative cable.
Remove the combination flasher from its wire har-
TURN SIGNAL AND HAZARD WARNING ness connector and replace it with a known good
SYSTEMS unit. Connect the battery negative cable. Test the
When diagnosing the turn signal or hazard warn- operation of the turn signal and hazard warning sys-
ing circuits, remember that high generator output tems. If OK, discard the faulty combination flasher.
can burn out bulbs rapidly and repeatedly. If this is a If not OK, remove the test flasher and go to Step 6.
problem on the vehicle being diagnosed, refer to (6) Turn the ignition switch to the On position.
Charging System in the Diagnosis and Testing sec- Check for battery voltage at the combo flasher input
tion of Group 8C - Charging System for further diag- circuit cavity in the combination flasher wire harness
nosis of a possible generator overcharging condition. connector. If OK, go to Step 7. If not OK, go to Step
If the problem being diagnosed is related to a fail- 9.
ure of the turn signals to automatically cancel follow- (7) Turn the ignition switch to the Off position.
ing completion of a turn, inspect the multi-function Place the hazard warning switch in the On position.
switch for a faulty or damaged cancel actuator and Check for battery voltage again at the combo flasher
inspect the turn signal cancelling cam lobes on the input circuit cavity in the combination flasher wire
clockspring mechanism for damage or improper harness connector. If OK, go to Step 8. If not OK, go
installation. For complete circuit diagrams, refer to to Step 9.
Turn Signals in the Contents of Group 8W - Wiring (8) Disconnect and isolate the battery negative
Diagrams. cable. Check for continuity between the ground cir-
cuit cavity of the combination flasher wire harness
connector and a good ground. There should be conti-
nuity. If OK, go to Step 9. If not OK, repair the open
ground circuit to ground as required.
(9) Disconnect the instrument panel wire harness
connector from the multi-function switch connector
receptacle. Check for continuity between the combo
flasher input circuit cavities in the combination
flasher wire harness connector and in the instrument
panel wire harness connector for the multi-function
switch. There should be continuity. If OK, go to Step
10. If not OK, repair the open combo flasher input
circuit as required.
(10) Check for continuity between the combo
flasher output circuit cavities in the combination
flasher wire harness connector and in the instrument
panel wire harness connector for the multi-function
switch. There should be continuity. If OK, refer to
Turn Signal Switch and Hazard Warning Switch
in the Diagnosis and Testing section of this group. If
not OK, repair the open combo flasher output circuit
as required.

WARNING SWITCH Fig. 3 Multi-Function Switch Continuity
The turn signal switch and the hazard warning REMOVAL AND INSTALLATION
switch are integral to the multi-function switch.
Refer to Turn Signal and Hazard Warning Sys- COMBINATION FLASHER
tems in the Diagnosis and Testing section of this
group before testing the multi-function switch. For WARNING: ON VEHICLES EQUIPPED WITH AIR-
complete circuit diagrams, refer to Turn Signals in BAGS, REFER TO GROUP 8M - PASSIVE
the Contents of Group 8W - Wiring Diagrams. RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
WARNING: ON VEHICLES EQUIPPED WITH AIR- INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
BAGS, REFER TO GROUP 8M - PASSIVE SERVICE. FAILURE TO TAKE THE PROPER PRE-
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
STEERING WHEEL, STEERING COLUMN, OR BAG DEPLOYMENT AND POSSIBLE PERSONAL
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR INJURY.
BAG DEPLOYMENT AND POSSIBLE PERSONAL REMOVAL
INJURY. (1) Disconnect and isolate the battery negative
cable.
(1) Disconnect and isolate the battery negative (2) Remove the knee blocker from the instrument
cable. Disconnect the instrument panel wire harness panel. Refer to Knee Blocker in the Removal and
connector from the multi-function switch connector Installation section of Group 8E - Instrument Panel
receptacle. Systems for the procedures.
(2) Using an ohmmeter, perform the switch conti-
nuity checks at the connector receptacle terminals as NOTE: The combination flasher and flasher bracket
shown in the Multi-Function Switch Continuity chart are serviced only as a unit.
(Fig. 3).
(3) If the turn signal switch or hazard warning (3) Reach through the inboard side of the instru-
switch fails any of the continuity checks, replace the ment panel steering column opening to access and
faulty multi-function switch assembly as required. If remove the screw that secures the combination
the switch circuits are OK, repair the lighting cir- flasher bracket to the upper steering column mount-
cuits as required. ing bracket to the right of the steering column (Fig.
4).

WARNING SWITCH
INJURY.
REMOVAL
cable.
(2) Remove the knee blocker from the instrument
Fig. 4 Combination Flasher Remove/Install Installation section of Group 8E - Instrument Panel
(4) Lower the combination flasher and bracket far Systems for the procedures.
enough to access the wire harness connector. (3) Remove the three screws that secure the lower
(5) Remove the combination flasher from the wire steering column shroud to the upper shroud (Fig. 5).
harness connector.
(6) Remove the combination flasher and bracket
from under the instrument panel as a unit.
INSTALLATION
(1) Position the combination flasher and bracket
under the instrument panel as a unit.
(2) Align the combination flasher terminals with
the terminal cavities in the wire harness connector.
(3) Push in firmly on the combination flasher until
the terminals are fully seated in the terminal cavities
in the wire harness connector.
(4) Position the combination flasher and bracket to
the upper steering column mounting bracket to the
right of the steering column under the instrument
panel.
combination flasher and bracket to the upper steer-
ing column mounting bracket. Tighten the screw to 4
N·m (35 in. lbs.).
(6) Install the knee blocker onto the instrument
Installation section of Group 8E - Instrument Panel
Fig. 5 Steering Column Shrouds Remove/Install
(4) If the vehicle is equipped with a standard non-
tilt steering column, loosen the two upper steering
column mounting nuts. If the vehicle is equipped
with the optional tilt steering column, move the tilt
steering column to the fully lowered position.
(5) Remove both the upper and lower shrouds from (10) Disconnect the two instrument panel wire
the steering column. harness connectors from the multi-function switch
(6) Remove the two screws that secure the multi- connector receptacles.
function switch water shield and bracket to the top of (11) Remove the multi-function switch and water
the steering column (Fig. 6). shield from the steering column as a unit.
(12) Gently and carefully remove the water shield
from the switch by pulling it over the hazard warn-
ing switch button and the multi-function switch con-
trol stalk.
INSTALLATION
(1) Gently and carefully install the water shield
onto the switch by pulling it over the hazard warning
switch button and the multi-function switch control
stalk.
(2) Position the multi-function switch and water
shield near its mounts on the steering column as a
unit.
(3) Reconnect the two instrument panel wire har-
ness connectors to the multi-function switch connec-
tor receptacles.
Fig. 6 Water Shield Upper Screws Remove/Install (4) Position the multi-function switch onto its
(7) Remove the one screw located below the multi- mounts on the left side of the steering column. If the
function switch control stalk that secures the multi- vehicle is equipped with the optional tilt steering col-
function switch water shield and bracket to the umn, lifting gently upward on the tilt release lever
steering column (Fig. 7). will provide additional clearance to ease multi-func-
tion switch installation.
(5) Position the lower mounting tab of the multi-
function switch water shield bracket to the steering
column screw boss below the multi-function switch
control stalk.
(6) Install and tighten the one screw located below
the multi-function switch control stalk that secures
the multi-function switch water shield and bracket to
the steering column. Tighten the screw to 1.1 N·m
(10 in. lbs.).
the multi-function switch water shield and bracket to
the top of the steering column. Tighten the screws to
2.2 N·m (20 in. lbs.).
(8) Position both the upper and lower shrouds onto
the steering column.
Fig. 7 Water Shield Lower Screw Remove/Install (9) Install and tighten the three screws that secure
the lower steering column shroud to the upper
(8) Gently pull the lower mounting tab of the
shroud. Tighten the screws to 2 N·m (18 in. lbs.).
multi-function switch water shield bracket away from
(10) If the vehicle is so equipped, tighten the two
the steering column far enough to clear the screw
nuts that secure the non-tilt steering column upper
boss below the multi-function switch control stalk.
mounting bracket to the dash panel steering column
(9) Lift the water shield and bracket with the
support bracket studs. Tighten the nuts to 22 N·m
multi-function switch off of the left side of the steer-
(200 in. lbs.).
ing column far enough to access the two multi-func-
(11) Install the knee blocker onto the instrument
tion switch wire harness connectors. If the vehicle is
equipped with the optional tilt steering column, lift-
ing gently upward on the tilt release lever will pro-
vide additional clearance to ease multi-function
switch removal.
TJ WIPER AND WASHER SYSTEMS 8K - 1
WIPER AND WASHER SYSTEMS

CONTENTS
page page
GENERAL INFORMATION WIPER SWITCH AND WASHER SWITCH . . . . . . 3

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1 DIAGNOSIS AND TESTING
DESCRIPTION AND OPERATION WASHER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . 6
REAR WIPER AND WASHER SYSTEM . . . . . . . 1 WIPER SWITCH AND WASHER SWITCH . . . . . . 7
WASHER NOZZLE AND PLUMBING . . . . . . . . . . 3 WIPER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . 4
WASHER PUMP . . . . . . . . . . . . . . . . . . . . . . . . . 3 REMOVAL AND INSTALLATION
WASHER RESERVOIR . . . . . . . . . . . . . . . . . . . . 3 WASHER SYSTEM . . . . . . . . . . . . . . . . . . . . . . 12
WINDSHIELD WASHER SYSTEM . . . . . . . . . . . . 1 WIPER ARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WINDSHIELD WIPER SYSTEM . . . . . . . . . . . . . 1 WIPER BLADE . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WIPER ARM AND BLADE . . . . . . . . . . . . . . . . . . 2 WIPER LINKAGE AND PIVOT . . . . . . . . . . . . . . . 9
WIPER LINKAGE AND PIVOT . . . . . . . . . . . . . . . 2 WIPER MOTOR . . . . . . . . . . . . . . . . . . . . . . . . . . 9
WIPER MOTOR . . . . . . . . . . . . . . . . . . . . . . . . . . 2 WIPER SWITCH AND WASHER SWITCH . . . . . 10
GENERAL INFORMATION WINDSHIELD WASHER SYSTEM

An electrically operated windshield washer system
INTRODUCTION is standard equipment. A washer reservoir in the
Following are general descriptions of the major engine compartment holds the washer fluid, which is
components in the wiper and washer systems. Refer pressurized by a pump when the windshield washer
to 8W-53 - Wipers in Group 8W - Wiring Diagrams switch lever is actuated. The windshield washer
for complete circuit descriptions and diagrams. pump feeds the pressurized washer fluid through the
washer system plumbing to the windshield washer
nozzles.
DESCRIPTION AND OPERATION If the vehicle is equipped with the two-speed wiper
system and the wipers are not already turned on
WINDSHIELD WIPER SYSTEM when the washers are activated, the wiper switch
A two-speed windshield wiper system is standard will be turned on to the low speed position automat-
equipment on this model. An intermittent windshield ically. The wipers must be turned off manually fol-
wiper system is optional. The standard system lets lowing a washer switch activation. If the vehicle is
the driver select from two wiper speeds, low or high. equipped with the intermittent wipe system and the
The intermittent wiper system adds an intermittent wipers are not turned on when the washers are acti-
wipe delay feature. vated, the wipers will be automatically cycled for one
On models equipped with the intermittent wiper or two wipes, then be turned off.
system, the intermittent wipe mode delay times are The washers will operate only when the ignition
driver adjustable from about one second to about fif- switch is in the Accessory or On positions. A fuse
teen seconds. The intermittent wipe mode is provided located in the fuseblock module protects the circuitry
by delay logic and relay control circuitry contained of the washer system. Refer to the owner’s manual
within the intermittent wiper/washer switch. The for more information on the windshield washer sys-
intermittent wipe relay is also contained within the tem controls and operation.
switch.
The windshield wipers will operate only when the REAR WIPER AND WASHER SYSTEM
ignition switch is in the Accessory or On positions. A A rear wiper and washer system is standard equip-
fuse located in the fuseblock module protects the cir- ment on models equipped with the optional hardtop.
cuitry of either windshield wiper system. Refer to the The rear wiper system provides the following operat-
owner’s manual for more information on the winding modes:
shield wiper system controls and operation. • Continuous fixed-cycle wipe.
• A rear washer mode.
8K - 2 WIPER AND WASHER SYSTEMS TJ
• A park mode that operates the wiper motor until The driver side wiper pivot crank arm and the
the blade reaches its park position when the rear wiper motor crank arm each have ball studs on their
wiper switch is placed in the Off position. ends. The passenger side crank arm has two ball
A single switch in the instrument panel accessory studs. A drive link is connected from the motor crank
switch bezel controls both the rear wiper and washer arm ball stud to one ball stud on the passenger side
functions. The rear washer system shares the reser- pivot crank arm. A connecting link is connected from
voir of the windshield washer system, but has its the other ball stud on the passenger side pivot crank
own dedicated washer pump and plumbing. arm to the driver side pivot crank arm ball stud.
The rear wiper and washer systems will operate Both the drive link and the connector link have a
only when the ignition switch is in the On position. A plastic socket-type bushing on each end. Each of the
fuse in the fuseblock module protects the circuitry of socket-type bushings are snap-fit over their respec-
both the rear wiper and washer systems. tive ball studs.
Refer to the owner’s manual for more information The wiper linkage, pivots, bushings, motor, crank
on the rear wiper and washer system controls and arm, and mounting bracket are only serviced as a
operation. complete unit. If any part of this assembly except the
motor is faulty or damaged, the entire unit must be
WIPER ARM AND BLADE replaced. The wiper motor is also available as a sep-
All models have two 33.02-centimeter (13-inch) arate service item.
windshield wiper blades with non-replaceable rubber
elements (squeegees). The rear wiper uses a single WIPER MOTOR
45.72-centimeter (18-inch) wiper blade with a non-re-
placeable rubber element (squeegee). FRONT
Caution should be exercised to protect the rubber The two-speed permanent magnet wiper motor has
squeegees from any petroleum-based cleaners or con- an integral transmission and park switch. The motor
taminants, which will rapidly deteriorate the rubber. also contains an internal automatic resetting circuit
If the squeegees are damaged, worn, or contami- breaker to protect the motor from overloads. The
nated, the entire wiper blade assembly must be motor is secured to the wiper linkage and pivot mod-
replaced. ule bracket with three screws and is protected by a
Wiper squeegees exposed to the elements for a long rubber boot. The wiper motor output shaft passes
time tend to lose their wiping effectiveness. Periodic through a hole in the module bracket, where a nut
cleaning of the squeegees is suggested to remove secures the wiper motor crank arm to the motor out-
deposits of salt and road film. The wiper blades, put shaft.
arms, and windshield or rear liftglass should be Wiper speed is controlled by current flow to the
cleaned with a sponge or cloth and windshield proper set of brushes. The wiper motor completes its
washer fluid, a mild detergent, or a non-abrasive wipe cycle when the windshield wiper switch stalk is
cleaner. If the squeegees continue to streak or smear, moved to the Off position, and parks the blades in
the wiper blades should be replaced. the lowest portion of the wipe pattern.
The blades are mounted to spring-loaded wiper The windshield wiper motor cannot be repaired. If
arms. The spring tension of the wiper arms controls faulty or damaged, the entire wiper motor and boot
the pressure applied to the blades on the glass. The assembly must be replaced. The wiper linkage and
windshield wiper arms are secured by an integral pivots module, which includes the wiper motor, is
latch to the two wiper pivots on the cowl plenum cov- also available for service.
er/grille panel at the base of the windshield. The rear
wiper arm is secured by an integral latch directly to REAR
the rear wiper motor output shaft on the liftglass. The rear wiper motor is secured on the inside of
The wiper arms and blades cannot be adjusted or the liftglass with a slotted bracket that fits onto a
repaired. If faulty or damaged, they must be grommet under the right liftglass hinge mounting
replaced. nut. The motor output shaft passes through the lift-
glass, where a rubber gasket and a plastic bezel and
WIPER LINKAGE AND PIVOT nut unit seal and secure the output shaft to the out-
The wiper linkage and pivot module is secured side of the liftglass. The rear wiper arm is secured
with screws to the cowl plenum panel beneath the directly to the motor output shaft.
cowl plenum cover/grille panel. The wiper motor is The rear wiper motor unit contains an internal
secured with screws to the center of the linkage and park switch. The motor also contains an automatic
pivot module bracket. The wiper pivots are secured resetting thermal switch for overload protection.
to the ends of the module bracket.
The rear wiper motor cannot be repaired. If faulty is pushed down to its detent to activate the rear
or damaged, the entire rear wiper motor assembly wiper system, and down again to the momentary
must be replaced. position to activate the rear washer system. Both the
rear wiper and rear washer motors will operate con-
WIPER SWITCH AND WASHER SWITCH tinuously for as long as the switch is held in the
momentary Wash position.
FRONT The rear wiper and washer switch cannot be
The windshield wiper and washer switches are repaired and, if faulty or damaged, the entire switch
mounted on the right side of the steering column unit must be replaced.
(Fig. 1). The switch stalk is moved up or down to
select the wiper switch mode, and pulled towards the WASHER RESERVOIR
steering wheel to activate the washer system. Models A single washer fluid reservoir is used for both the
with the intermittent wiper system also have a knob front and rear washer systems. The washer fluid res-
on the end of the switch stalk, which is rotated to ervoir is secured to the inner fender shield, over the
select the desired delay interval. The windshield left front wheel house in the engine compartment.
wiper and washer switch contains circuitry for the Each washer pump and motor unit has a barbed
following functions: nipple, which is installed through a rubber grommet
• Windshield wipers seal inserted in a hole near the bottom of the reser-
• Intermittent wiper delay relay control and logic voir. The washer pumps are retained by an interfer-
(if the vehicle is so equipped) ence fit between the barbed nipple and the grommet
• Intermittent wipe relay (if the vehicle is so seal, which is a light press fit.
equipped) The washer reservoir has a snap-fit filler cap with
• Windshield washers. a rubber gasket. The cap hinges on and is secured to
The windshield wiper and washer switch cannot be a molded-in hook formation on the reservoir behind
repaired. If any function of the switch is faulty, or if the filler neck.
the switch is damaged, the entire switch unit must The washer reservoir and filler cap are each avail-
be replaced. able for service.
WASHER PUMP
The washer pumps and motors are mounted near
the bottom of the washer reservoir. A barbed nipple
on the pump housing passes through a rubber grom-
met seal installed in a hole near the bottom of the
reservoir. The washer pump is retained by an inter-
ference fit between the barbed pump nipple and the
grommet seal, which is a light press fit.
A permanently lubricated and sealed motor is cou-
pled to a rotor-type pump. Washer fluid is gravity-fed
from the reservoir to the pump. When the motor is
energized, the pump pressurizes the washer fluid
and forces it through the plumbing to the nozzles.
The washer pump and motor unit cannot be
repaired. If faulty, the entire washer pump and
Fig. 1 Windshield Wiper Switch and Washer Switch motor unit must be replaced.
REAR WASHER NOZZLE AND PLUMBING

The single two-function rear wiper and washer
switch is installed in the instrument panel accessory FRONT
switch bezel, which is located near the bottom of the Pressurized washer fluid is fed through a single
instrument panel center bezel area, next to the ash hose, attached to a barbed nipple on the front washer
receiver. The rear wiper and washer switch controls pump. The hose is routed to a tee fitting located near
the rear wiper and washer functions. the rear inner hood panel reinforcement. Hoses from
The toggle-type switch features a detent in the On the tee fitting are routed to the two nozzles.
position, and a momentary Wash position. The rear A check valve is located in the washer supply line
wiper and washer switch also has an integral illumi- near each of the two front nozzles, which prevents
nation lamp with a serviceable bulb. The switch knob washer fluid drain-back or siphoning from occurring.
The nozzles are snapped into openings in the hood From the check valve, another single hose is routed
panel below the windshield through the rear liftglass opening reinforcements of
The two washer nozzles each emit two streams of the hardtop to the rear wiper motor cover. Behind
washer fluid into the wipe pattern (Fig. 2). If the aim the rear wiper motor cover, the hose attaches to the
of the washer fluid streams is unacceptable, each rear washer nozzle nipple.
stream can be adjusted using a pin inserted in the The fluidic rear washer nozzle and a seal are
nozzle orifice to rotate the nozzle ball. installed from the outside through a hole in the lift-
glass near the rear wiper motor output shaft. The
nozzle is secured on the inside of the glass by a plas-
tic hex nut.
The rear washer nozzle cannot be adjusted. The
nozzle, check valve, and hose fittings cannot be
repaired and, if faulty or damaged, they must be
replaced.

WIPER SYSTEM
Fig. 2 Windshield Washer Nozzles
The nozzles, check valves and hose fittings cannot
FRONT
be repaired and, if faulty or damaged, they must be For circuit descriptions and diagrams, refer to
replaced. 8W-53 - Wipers in Group 8W - Wiring Diagrams.

REAR BAGS, REFER TO GROUP 8M - PASSIVE
Pressurized washer fluid is fed through a single
hose, attached to a barbed nipple on the rear washer
pump. The hose is routed from the front of the vehi-
cle to the liftglass with the left body wire harness. At
the left rear corner of the hardtop, the hose connects
to a check valve, which prevents washer fluid drain-
back or siphoning from occurring.
INJURY.
There is also a washer hose cap attached to the
hose below the check valve (Fig. 3). When the hard- (1) Check the fuse in the fuseblock module. If OK,
top is removed from the vehicle, the body half of the go to Step 2. If not OK, repair the shorted circuit or
washer hose must be disconnected from the check component as required and replace the faulty fuse.
valve. The washer hose cap is used to plug the body (2) Disconnect and isolate the battery negative
half of the washer hose after it is disconnected from cable. Unplug the windshield wiper switch wire har-
the check valve. ness connector. Connect the battery negative cable.
Turn the ignition switch to the On position. Check
for battery voltage at the fused ignition switch out-
put (run/acc) circuit cavity of the wiper switch wire
harness connector. If OK, go to Step 3. If not OK,
repair the open circuit to the fuseblock module as
required.
(3) If the vehicle is equipped with the optional
intermittent wiper system and the problem being
diagnosed involves only the pulse wipe, wipe-after-
wash, or intermittent wipe modes, go to Step 4. If
not, go to Step 5.
Disconnect and isolate the battery negative cable.
Check for continuity between the ground circuit cav-
ity of the wiper switch wire harness connector and a
good ground. There should be continuity. If OK,
Fig. 3 Rear Washer Hose Cap
replace the faulty switch. If not OK, repair the open BAG DEPLOYMENT AND POSSIBLE PERSONAL
circuit to ground as required. INJURY.
Disconnect and isolate the battery negative cable. (1) Check the fuse in the fuseblock module. If OK,
Remove the windshield wiper and washer switch and go to Step 2. If not OK, repair the shorted circuit or
check the switch continuity. See Wiper Switch and component as required and replace the faulty fuse.
Washer Switch in the Diagnosis and Testing section (2) Disconnect and isolate the battery negative
of this group for the procedures. If OK, go to Step 6. cable. Remove the accessory switch bezel and unplug
If not OK, replace the faulty switch. the wire harness connector from the rear wiper and
(6) Unplug the windshield wiper motor wire har- washer switch. Connect the battery negative cable.
ness connector. Check for continuity between the Turn the ignition switch to the On position. Check
ground circuit cavity in the body half of the wiper for battery voltage at the rear washer switch output
motor wire harness connector and a good ground. circuit cavity of the rear wiper and washer switch
There should be continuity. If OK, go to Step 7. If not wire harness connector. If OK, go to Step 3. If not
OK, repair the open circuit to ground as required. OK, repair the open circuit to the fuseblock module
(7) Connect the battery negative cable. Turn the as required.
ignition switch to the On position. Check for battery (3) Turn the ignition switch to the Off position.
voltage at the fused ignition switch output (run/acc) Disconnect and isolate the battery negative cable.
circuit cavity in the body half of the wiper motor wire Check for continuity between the ground circuit cav-
harness connector. If OK, go to Step 8. If not OK, ity of the rear wiper and washer switch wire harness
repair the open circuit to the fuseblock module as connector and a good ground. There should be conti-
required. nuity. If OK, go to Step 4. If not OK, repair the open
(8) Turn the ignition switch to the Off position. circuit to ground as required.
Disconnect and isolate the battery negative cable. (4) Test the rear wiper and washer switch continu-
With the windshield wiper and washer switch wire ity. See Wiper Switch and Washer Switch in the
harness connector still unplugged, check the cavities Diagnosis and Testing section of this group for the
for each of the following circuits in the body half of procedures. If OK, go to Step 5. If not OK, replace
the wiper motor wire harness connector for continu- the faulty switch.
ity to ground. In each case, there should be no conti- (5) Remove the rear wiper motor cover and unplug
nuity. If OK, go to Step 9. If not OK, repair the short the rear wiper motor wire harness connector. Con-
circuit as required. nect the battery negative cable. Turn the ignition
• Wiper park switch sense switch to the On position. Check for battery voltage
• Wiper switch low speed output at the fused ignition switch output (run) circuit cav-
• Wiper switch high speed output. ity of the rear wiper motor wire harness connector. If
(9) Check for continuity between the cavities in OK, go to Step 6. If not OK, repair the open circuit to
the body half of the wiper motor wire harness con- the fuseblock module as required.
nector and the cavities in the windshield wiper and (6) Turn the ignition switch to the Off position.
washer switch wire harness connector for each of the Disconnect and isolate the battery negative cable.
following circuits. In each case, there should be con- Check for continuity between the ground circuit cav-
tinuity. If OK, replace the faulty wiper motor. If not ity of the rear wiper motor wire harness connector
OK, repair the open circuit as required. and a good ground. There should be continuity. If
• Wiper park switch sense OK, go to Step 7. If not OK, repair the open circuit to
• Wiper switch low speed output ground as required.
• Wiper switch high speed output. (7) Check for continuity between the rear wiper
motor control circuit cavity of the rear wiper motor
REAR wire harness connector and a good ground. There
For circuit descriptions and diagrams, refer to should be no continuity. If OK, go to Step 8. If not
8W-53 - Wipers in Group 8W - Wiring Diagrams. OK, repair the short circuit as required.
(8) Check for continuity between the rear wiper
WARNING: ON VEHICLES EQUIPPED WITH AIR- motor control circuit cavities of the rear wiper motor
BAGS, REFER TO GROUP 8M - PASSIVE wire harness connector and the rear wiper and
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY washer switch wire harness connector. There should
STEERING WHEEL, STEERING COLUMN, OR be continuity. If OK, replace the faulty rear wiper
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR motor. If not OK, repair the open circuit as required.
WASHER SYSTEM REAR

The diagnosis found here addresses an inoperative
FRONT rear washer pump. If the washer pump operates, but
The diagnosis found here addresses an inoperative no washer fluid is emitted from the washer nozzle, be
front washer pump. If the washer pump operates, certain to check the fluid level in the reservoir. Check
but no washer fluid is emitted from the washer noz- for ice or other foreign material in the reservoir, and
zles, be certain to check the fluid level in the reser- for pinched, disconnected, broken, or incorrectly
voir. Check for ice or other foreign material in the routed washer system plumbing. For circuit descrip-
reservoir, and for pinched, disconnected, broken, or tions and diagrams, refer to 8W-53 - Wipers in Group
incorrectly routed washer system plumbing. For cir- 8W - Wiring Diagrams.
cuit descriptions and diagrams, refer to 8W-53 - Wip-
ers in Group 8W - Wiring Diagrams. WARNING: ON VEHICLES EQUIPPED WITH AIR-
INJURY. (1) Turn the ignition switch to the On position.
Place the rear wiper/washer switch in the Wipe posi-
(1) Turn the ignition switch to the On position. tion. Check whether the rear wiper is operating. If
Turn the wiper switch to the Low or High speed posi- OK, go to Step 2. If not OK, see the Wiper System
tion. Check whether the wipers operate. If OK, go to diagnosis in this group.
Step 2. If not OK, see the Wiper System diagnosis in (2) Turn the ignition switch to the Off position.
this group. Disconnect and isolate the battery negative cable.
(2) Turn the ignition switch to the Off position. Unplug the rear washer pump wire harness connec-
Disconnect and isolate the battery negative cable. tor. Check for continuity between the ground circuit
Unplug the front washer pump wire harness connec- cavity of the rear washer pump wire harness connec-
tor. Check for continuity between the ground circuit tor and a good ground. There should be continuity. If
cavity of the front washer pump wire harness connec- OK, go to Step 3. If not OK, repair the open circuit to
tor and a good ground. There should be continuity. If ground as required.
OK, go to Step 3. If not OK, repair the open circuit to (3) Connect the battery negative cable. Turn the
ground as required. ignition switch to the On position. Check for battery
(3) Connect the battery negative cable. Turn the voltage at the rear washer motor control circuit cav-
ignition switch to the On position. Check for battery ity of the rear washer pump wire harness connector
voltage at the front washer switch output circuit cav- while the rear washer switch is actuated. If OK,
ity of the front washer pump wire harness connector replace the faulty pump. If not OK, go to Step 4.
while actuating the washer switch. If OK, replace the (4) Turn the ignition switch to the Off position.
faulty washer pump. If not OK, go to Step 4. Disconnect and isolate the battery negative cable.
(4) Turn the ignition switch to the Off position. Unplug the rear wiper/washer switch wire harness
Disconnect and isolate the battery negative cable. connector. Check for continuity between the rear
Unplug the windshield wiper/washer switch wire washer motor control circuit cavity of the rear
harness connector. Check for continuity between the washer pump wire harness connector and a good
front washer switch output circuit cavity of the front ground. There should be no continuity. If OK, go to
washer pump wire harness connector and a good Step 5. If not OK, repair the short circuit as
ground. There should be no continuity. If OK, go to required.
Step 5 If not OK, repair the short circuit as required. (5) Check for continuity between the rear washer
(5) Check for continuity between the front washer motor control circuit cavities of the rear washer
switch output circuit cavities of the front washer pump wire harness connector and the rear wiper/
pump wire harness connector and the wiper/washer washer switch wire harness connector. There should
switch wire harness connector. There should be con- be continuity. If OK, replace the faulty switch. If not
tinuity. If OK, replace the faulty switch. If not OK, OK, repair the open circuit as required.
repair the open circuit as required.
WIPER SWITCH AND WASHER SWITCH REAR

Perform the diagnosis for the rear wiper system
FRONT and/or washer system as described in this group
Perform the diagnosis for the front wiper system before testing the rear wiper and washer switch. For
and/or washer system as described in this group circuit descriptions and diagrams, see 8W-53 - Wip-
before testing the front wiper and washer switch. For ers in Group 8W - Wiring Diagrams.
circuit descriptions and diagrams, see 8W-53 - Wip-
ers in Group 8W - Wiring Diagrams. WARNING: ON VEHICLES EQUIPPED WITH AIR-
INJURY. (1) Remove the accessory switch bezel from the
instrument panel and unplug the rear wiper and
(1) Disconnect and isolate the battery negative washer switch wire harness connector.
cable. (2) Using an ohmmeter, check the rear wiper and
(2) Remove the front wiper and washer switch washer switch continuity at the switch terminals as
from the steering column and unplug the wire har- shown in the Rear Wiper Switch and Washer Switch
ness connector from the switch. Continuity chart (Fig. 5).
(3) Using an ohmmeter, perform the switch conti-
nuity checks at the switch terminals as shown in the
Windshield Wiper Switch and Washer Switch Conti-
nuity chart (Fig. 4).
Fig. 5 Rear Wiper Switch and Washer Switch

Continuity
(3) If the switch fails any of the continuity checks,
Fig. 4 Windshield Wiper Switch and Washer Switch replace the faulty switch. If the switch is OK, repair
Continuity the rear wiper system and/or washer system wire
(4) If the switch fails any of the continuity checks, harness circuits as required.
replace the faulty switch. If the switch is OK, repair
the wiper system and/or washer system wire harness
circuits as required.
REMOVAL AND INSTALLATION WIPER ARM

WIPER BLADE CAUTION: The use of a screwdriver or other prying
tool to remove a wiper arm may distort it. This dis-
FRONT tortion could allow the arm to come off of the pivot
shaft, regardless of how carefully it is installed.
NOTE: The notched retainer end of the wiper ele-
ment should always be oriented towards the end of
the wiper blade that is nearest to the wiper pivot. FRONT
(1) Lift the wiper arm to permit the latch to be
(1) Lift the wiper arm to raise the wiper blade and pulled out to its holding position, then release the
element off of the windshield glass. arm (Fig. 7). The arm will remain off the windshield
(2) To remove the wiper blade from the wiper arm, with the latch in this position.
push the release tab under the arm tip and slide the
blade away from the tip towards the pivot end of the
arm (Fig. 6).
Fig. 6 Wiper Blade Remove/Install - Typical

(3) To install the wiper blade on the wiper arm, Fig. 7 Wiper Arm Remove/Install
slide the blade retainer into the U-shaped formation
(2) Remove the arm from the pivot using a rocking
on the tip of the wiper arm until the release tab
motion.
snaps into its locked position. Be certain that the
(3) Install the arm and blade with the wiper motor
notched retainer for the wiper element is oriented
in the Park position. See the Front Wiper Arm
towards the end of the wiper blade that is nearest to
Installation illustration (Fig. 8).
the wiper pivot.
REAR
NOTE: The notched retainer end of the wiper ele-
ment should always be oriented towards the end of
the wiper blade that is nearest to the wiper pivot.
(1) Lift the rear wiper arm to raise the wiper blade
and element off of the rear liftglass.
(2) To remove the wiper blade from the wiper arm,
push the release tab under the arm tip and slide the
blade away from the tip towards the rear wiper
motor output shaft end of the arm (Fig. 6).
(3) To install the wiper blade on the wiper arm, Fig. 8 Front Wiper Arm Installation
slide the blade retainer into the U-shaped formation
on the tip of the wiper arm until the release tab (4) Mount the arms on the pivot shafts so that the
snaps into its locked position. Be certain that the tip of the wiper blade is on the upper edge of the
notched retainer for the wiper element is oriented lower windshield blackout area, + 15 mm/ – 0 mm (+
towards the end of the wiper blade that is nearest to 0.59 in./ – 0 in.).
the rear wiper motor output shaft. (5) Lift the wiper arm away from the windshield
slightly to relieve the spring tension on the latch.
Push the latch into the locked position and slowly (2) Remove the wiper arms from the wiper pivots.
release the arm until the wiper blade rests on the See Wiper Arm in this group for the procedures.
windshield. (3) Remove the one screw that secures the center
(6) Operate the wipers with the windshield glass of the cowl plenum cover/grille panel to the cowl ple-
wet, then turn the wiper switch to the Off position. num panel.
Check for the correct wiper arm positioning and (4) Remove the four screws that secure the cowl
readjust if required. plenum cover/grille panel to the cowl panel near the
base of the windshield.
REAR (5) Open and support the hood
(1) Lift the wiper arm to permit the latch to be (6) Pull each end of the cowl to hood seal away
pulled out to its holding position, then release the from the metal flange where the dash panel and cowl
arm (Fig. 7). The arm will remain off the liftglass plenum panel meet far enough to access the one
with the latch in this position. screw that secures each outboard end of the cowl ple-
(2) Remove the wiper arm from the motor output num cover/grille panel to the cowl plenum panel (Fig.
shaft using a rocking motion. 10).
(3) Install the rear wiper arm with the wiper
motor in the Park position. Place the rear wiper
blade on the liftglass so that it is parallel to or tipped
down from the upper edge of the liftglass a maximum
of 80 mm (3.14 in.) (Fig. 9).
Fig. 9 Rear Wiper Arm Installation

(4) Lift the wiper arm away from the liftglass
slightly to relieve the spring tension on the latch.
Push the latch into the locked position and slowly
release the arm until the wiper blade rests on the Fig. 10 Cowl Plenum Cover/Grille Panel Remove/
liftglass. Install
(5) Operate the wiper with the liftglass wet, then (7) Remove the one screw that secures each out-
turn the wiper switch to the Off position. Check for board end of the cowl plenum cover/grille panel to
the correct wiper arm positioning and readjust if the cowl plenum panel.
required. (8) Carefully remove the cowl plenum cover/grille
panel from the vehicle, so as not to damage the paint
WIPER LINKAGE AND PIVOT around the pivot openings of the panel.
The wiper linkage and pivots can only be removed (9) Reach into the cowl plenum and unplug the
from or installed in the vehicle as a unit with the wiper motor wire harness connector.
wiper motor. See Wiper Motor in this group for the (10) Remove the three screws that secure the
service procedures. wiper module mounting bracket to the cowl plenum
panel (Fig. 11).
WIPER MOTOR (11) Remove the wiper module from the cowl ple-
num as a unit.
FRONT (12) Release the retainer that secures the wiper
(1) Disconnect and isolate the battery negative motor wire harness connector to the wiper module
cable. bracket.
Fig. 12 Rear Wiper and Washer System

(7) Loosen, but do not remove, the right liftglass
hinge nut.
(8) From the inside of the liftglass, gently pull the
rear wiper motor away from the liftglass until the
output shaft clears the hole in the liftglass.
Fig. 11 Wiper Module Assembly Remove/Install (9) Move the motor towards the right side of the
(13) Turn the wiper module over and remove the vehicle until the slotted hole in the motor mounting
nut that secures the wiper linkage crank arm to the bracket clears the grommet under the right liftglass
wiper motor output shaft. hinge nut.
(14) Remove the three screws that secure the (10) Remove the rear wiper motor from the vehi-
wiper motor to the wiper module mounting bracket. cle.
(15) Remove the wiper motor from the wiper mod- (11) Reverse the removal procedures to install.
ule bracket. Tighten the mounting hardware as follows:
(16) Reverse the removal procedures to install. • Wiper motor output shaft nut - 3.3 N·m (30 in.
Tighten the mounting hardware as follows: lbs.)
• Wiper motor screws - 6 N·m (53 in. lbs.) • Liftglass hinge nut - 6 N·m (53 in. lbs.)
• Crank arm nut - 11.5 N·m (101 in. lbs.) • Wiper motor cover screws - 1.1 N·m (10 in. lbs.).
• Wiper module bracket screws - 7.9 N·m (70 in.
lbs.) WIPER SWITCH AND WASHER SWITCH
• Cowl plenum cover/grille panel screws - 1.7 N·m
(15 in. lbs.). FRONT
REAR WARNING: ON VEHICLES EQUIPPED WITH AIR-
(1) Disconnect and isolate the battery negative BAGS, REFER TO GROUP 8M - PASSIVE
cable. RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
(2) From the outside of the liftglass, remove the STEERING WHEEL, STEERING COLUMN, OR
rear wiper arm from the rear wiper motor output INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
shaft. See Wiper Arm in this group for the proce- SERVICE. FAILURE TO TAKE THE PROPER PRE-
dures. CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
(3) From the outside of the liftglass, remove the BAG DEPLOYMENT AND POSSIBLE PERSONAL
rear wiper motor output shaft nut and bezel unit INJURY.
(Fig. 12).
(4) From the outside of the liftglass, remove the (1) Disconnect and isolate the battery negative
rear wiper motor output shaft rubber gasket. cable.
(5) From the inside of the liftglass, remove the (2) Remove the knee blocker from the instrument
three screws that secure the rear wiper motor cover panel. See Knee Blocker in Group 8E - Instrument
to the motor. Panel Systems for the procedures.
(6) Unplug the rear wiper motor wire harness con- (3) Remove the three screws that secure the lower
nector. steering column shroud to the upper shroud (Fig. 13).
(7) Remove the one screw located below the multi-
function switch lever that secures the switch water
shield and bracket to the steering column (Fig. 15).
Fig. 15 Water Shield Lower Screw Remove/Install

(8) Gently pull the lower mounting tab of the
switch water shield bracket away from the steering
column far enough to clear the screw boss below the
multi-function switch lever.
Fig. 13 Steering Column Shrouds Remove/Install (9) Lift the water shield and bracket with the
multi-function switch off of the left side of the steer-
ing column as a unit and move it out of the way. If
tilt steering column, loosen the two upper steering
the vehicle is equipped with the optional tilt steering
column mounting nuts. If the vehicle is equipped
column, lifting gently upward on the tilt release lever
with the optional tilt steering column, move the tilt
will provide additional clearance to ease multi-func-
steering column to the fully lowered position.
tion switch removal.
(5) Remove both the upper and lower shrouds from
(10) Gently pull the windshield wiper and washer
the steering column.
switch up and away from the right side of the steer-
(6) Remove the two screws that secure the switch
ing column far enough to access the wire harness
water shield and bracket to the top of the steering
connector.
column (Fig. 14).
windshield wiper and washer switch.
(12) Remove the windshield wiper and washer
switch from the steering column.
Tighten the upper switch mounting screws to 2.2
N·m (20 in. lbs.). Tighten the lower switch water
shield and bracket screw to 1.1 N·m (10 in. lbs.).
Tighten the non-tilt steering column mounting nuts
to 22 N·m (200 in. lbs.) and the steering column
shroud mounting screws to 2 N·m (18 in. lbs.).
Fig. 14 Water Shield Upper Screws Remove/Install

REAR bezel are fully engaged. Tighten the mounting screws
to 2.2 N·m (20 in. lbs.).
BAGS, REFER TO GROUP 8M - PASSIVE WASHER SYSTEM
STEERING WHEEL, STEERING COLUMN, OR WASHER RESERVOIR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR (1) Disconnect and isolate the battery negative
SERVICE. FAILURE TO TAKE THE PROPER PRE- cable.
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- (2) Remove the three screws that secure the
BAG DEPLOYMENT AND POSSIBLE PERSONAL washer reservoir to the inner fender (Fig. 17).
INJURY.

cable.
panel. See Instrument Panel Center Bezel in Group
8E - Instrument Panel Systems for the procedures.
(3) Remove the four screws that secure the acces-
sory switch bezel to the instrument panel (Fig. 16).
Fig. 17 Washer Reservoir Remove/Install

(3) Lift the reservoir far enough to access the
washer pump(s).
(4) Remove the washer supply hose(s) from the
washer pump(s) and drain the washer fluid from the
Fig. 16 Accessory Switch Bezel Remove/Install reservoir into a clean container for reuse.
(5) Unplug the wire harness connector(s) from the
(4) Pull the accessory switch bezel out from the washer pump(s).
instrument panel far enough to access the wire har- (6) Remove the washer reservoir from the vehicle.
ness connectors. (7) Reverse the removal procedures to install.
(5) Unplug the wire harness connectors from the Tighten the reservoir mounting screws to 4 N·m (35
rear of the accessory switches and the cigar lighter/ in. lbs.).
power outlet.
(6) Remove the accessory switch bezel from the WASHER PUMP
instrument panel. (1) Disconnect and isolate the battery negative
(7) With a small thin-bladed screwdriver, gently cable.
pry the snap clips at the top and bottom of the rear (2) Remove the washer supply hose(s) from the
wiper and washer switch receptacle on the back of barbed outlet nipple of the washer pump(s) and drain
the accessory switch bezel and pull the switch out of the washer fluid from the reservoir into a clean con-
the bezel. tainer for reuse.
(8) Reverse the removal procedures to install. Be (3) Unplug the wire harness connector(s) from the
certain that both of the switch snap clip retainers in washer pump(s).
the receptacle on the back of the accessory switch (4) Using a trim stick or another suitable wide
flat-bladed tool, gently pry the barbed inlet nipple of
the washer pump out of the rubber grommet seal in
the reservoir. Care must be taken not to damage the
reservoir.
(5) Remove the rubber grommet seal from the res-
ervoir and discard.
Always use a new rubber grommet seal on the reser-
voir.
WASHER NOZZLE
FRONT
(1) Open and support the hood.
(2) From under the rear of the hood, disconnect
the washer supply hose from the barbed nipple of the
washer nozzle (Fig. 18).
Fig. 19 Rear Washer Nozzle Remove/Install
secures the threaded nozzle nipple from the inside of
the liftglass.
(6) Push the nozzle and seal out through the lift-
glass from the inside.
Tighten the washer nozzle nut to 0.9 N·m (8 in. lbs.).
CHECK VALVE
A check valve is located under the hood in the
washer supply line near each of the front washer
nozzles. Models with the optional rear washer system
also have a check valve in the washer supply line in
the left rear pillar of the hardtop, near where the
hardtop joins the vehicle body.
(1) Disconnect the washer supply hoses from the
Fig. 18 Front Washer Nozzles Remove/Install barbed nipples on each end of the front or rear
(3) From under the rear of the hood, gently washer system check valve.
squeeze the nozzle retainers and push the nozzle out (2) Remove the check valve from the vehicle.
through the top of the hood panel. (3) When reinstalling the check valve, be certain
(4) Reverse the removal procedures to install. See the valve is properly oriented within the system flow
Washer Nozzles and Plumbing in this group for the (Fig. 20).
nozzle adjustment procedures.
REAR
cable.
(2) From the inside of the liftglass, remove the
three screws that secure the rear wiper motor cover
to the motor (Fig. 19).
(3) Remove the rear wiper motor cover.
(4) Disconnect the washer supply hose from the
barbed rear washer nozzle nipple. Fig. 20 Washer System Check Valve
(5) While holding the nozzle securely from the out-
(4) Reverse the remaining removal procedures to
side of the liftglass, remove the plastic nut that
complete the installation.
TJ LAMPS 8L - 1
LAMPS
CONTENTS
page page
BULB APPLICATION . . . . . . . . . . . . . . . . . . . . . . 16 LAMP DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . 1

HEADLAMP ALIGNMENT . . . . . . . . . . . . . . . . . . . 5 LAMP SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . 11
LAMP BULB SERVICE . . . . . . . . . . . . . . . . . . . . . 8 LAMP SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . 15
LAMP DIAGNOSIS
INDEX
page page
GENERAL INFORMATION DIAGNOSTIC PROCEDURES . . . . . . . . . . . . . . . . 1

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . 1 FOG LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . 1 HEADLAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DAYTIME RUNNING LAMP . . . . . . . . . . . . . . . . . . 4
GENERAL INFORMATION this group. Damage to lamp and/or Daytime Run-

ning Lamp Module can result.
GENERAL INFORMATION Do not use fuses, circuit breakers or relays hav-
Each vehicle is equipped with various lamp assem- ing greater amperage value than indicated on the
blies. A good ground is necessary for proper lighting fuse panel or in the Owners Manual.
operation. Grounding is provided by the lamp socket
When it is necessary to remove components to ser-
when it comes in contact with the metal body, or
vice another, it should not be necessary to apply
through a separate ground wire.
excessive force or bend a component to remove it.
When changing lamp bulbs check the socket for
Before damaging a trim component, verify hidden
corrosion. If corrosion is present, clean it with a wire
fasteners or captured edges are not holding the com-
brush and coat the inside of the socket lightly with
ponent in place.
Mopar Multi-Purpose Grease or equivalent.
SAFETY PRECAUTIONS DIAGNOSIS AND TESTING

WARNING: EYE PROTECTION SHOULD BE USED DIAGNOSTIC PROCEDURES
WHEN SERVICING GLASS COMPONENTS. PER-
When a vehicle experiences problems with the
SONAL INJURY CAN RESULT.
headlamp system, verify the condition of the battery
connections, fuses, charging system, headlamp bulbs,
CAUTION: Do not touch the glass of halogen bulbs wire connectors, relay, high beam dimmer switch and
with fingers or other possibly oily surface, reduced headlamp switch. Refer to Group 8W, Wiring Dia-
bulb life will result. grams for component locations and circuit informa-
Do not use bulbs with higher candle power than tion.
indicated in the Bulb Application table at the end of
8L - 2 LAMPS TJ
HEADLAMP
HEADLAMP DIAGNOSIS
CONDITION POSSIBLE CAUSES CORRECTION
HEADLAMPS ARE DIM 1. Loose or corroded battery cables. 1. Clean and secure battery cable clamps
WITH ENGINE IDLING and posts.
OR IGNITION TURNED 2. Loose or worn generator drive 2. Adjust or replace generator drive belt.
OFF belt.
3. Charging system output too low. 3. Test and repair charging system, refer to
Group 8A,
4. Battery has insufficient charge. 4. Test battery state-of -charge
, refer to Group 8A.
5. Battery is sulfated or shorted. 5. Load test battery, refer to Group 8A.
6. Poor lighting circuit Z1-ground. 6. Test for voltage drop across Z1-ground
locations, refer to Group 8W.
7. Both headlamp bulbs defective. 7. Replace both headlamp bulbs.
HEADLAMP BULBS BURN 1. Charging system output too high. 1. Test and repair charging system, refer to
OUT Group 8A.
FREQUENTLY 2. Loose or corroded terminals or 2. Inspect and repair all connectors and
splices in circuit. splices, refer to Group 8W.
HEADLAMPS ARE DIM 1. Charging system output too low. 1. Test and repair charging system, refer to
WITH ENGINE RUNNING Group 8A.
ABOVE IDLE* 2. Poor lighting circuit Z1-ground. 2. Test for voltage drop across Z1-ground
locations, refer to Group 8W.
3. High resistance in headlamp 3. Test amperage draw of headlamp circuit.
circuit.
HEADLAMPS FLASH 1. Poor lighting circuit Z1-ground. 1. Test for voltage drop across Z1-ground
RANDOMLY locations, refer to Group 8W.
2. High resistance in headlamp 2. Test amperage draw of headlamp circuit.
circuit. Should not exceed 30 amps.
3. Faulty headlamps switch circuit 3. Replace headlamp switch.
breaker.
4. Loose or corroded terminals or 4. Inspect and repair all connectors and
splices in circuit. splices, refer to Group 8W.
HEADLAMPS DO NOT 1. No voltage to headlamps. 1. Repair open headlamp circuit, refer to

ILLUMINATE Group 8W.
2. No Z1-ground at headlamps. 2. Repair circuit ground, refer to Group 8W.
3. Faulty headlamp switch. 3. Replace headlamp switch.
4. Faulty headlamp dimmer 4. Replace multi-function switch.
(multi-function) switch.
5. Broken connector terminal or wire 5. Repair connector terminal or wire splice.
splice in headlamp circuit.
*Canada vehicles must have lamps ON.

TJ LAMPS 8L - 3
FOG LAMP
FOG LAMP DIAGNOSIS
FOG LAMPS ARE DIM 1. Loose or corroded battery cables. 1. Clean and secure battery cable clamps
WITH ENGINE IDLING OR and posts.
IGNITION TURNED OFF. 2. Loose or worn generator drive 2. Adjust or replace generator drive belt.
belt.
3. Charging system output too low. 3. Test and repair charging system. Refer to
Group 8A,
4. Battery has insufficient charge. 4. Test battery state-of -charge. Refer to
Group 8A.
5. Battery is sulfated or shorted. 5. Load test battery. Refer to Group 8A.
locations. Refer to Group 8W.
FOG LAMP BULBS BURN 1. Charging system output too high. 1. Test and repair charging system. Refer to
OUT FREQUENTLY Group 8A.

splices in circuit. splices. Refer to Group 8W.
FOG LAMPS ARE DIM 1. Charging system output too low. 1. Test and repair charging system. Refer to
ABOVE IDLE 2. Poor lighting circuit Z1-ground. 2. Test for voltage drop across Z1-ground
3. High resistance in fog lamp circuit. 3. Test amperage draw of fog lamp circuit.
FOG LAMPS FLASH 1. Poor lighting circuit Z1-ground. 1. Test for voltage drop across Z1-ground
RANDOMLY locations. Refer to Group 8W.
3. Faulty fog lamp switch. 3. Replace fog lamp switch.
FOG LAMPS DO NOT 1. Blown fuse for fog lamp. 1. Replace fuse. Refer to Group 8W.
ILLUMINATE 2. No Z1-ground at fog lamps. 2. Repair circuit ground. Refer to Group
8W.
splice in fog lamp circuit.
5. Defective or burned out bulb. 5. Replace bulb.
8L - 4 LAMPS TJ
DAYTIME RUNNING LAMP

DAYTIME RUNNING LAMP DIAGNOSIS

DAYTIME RUNNING LAMPS DO 1. Poor connection at DRL module. 1. Secure connector on DRL
NOT WORK 2. Parking brake engaged. module.
3. Parking brake circuit shorted to 2. Disengage parking brake.
ground. 3. Check voltage on pin 3 of
4. Headlamp circuit shorted to module, refer to Group 8W.
ground. 4. Check L3 circuit, refer to Group
5. Defective DRL module. 8W.
5. Replace DRL module.
TJ LAMPS 8L - 5
HEADLAMP ALIGNMENT
INDEX
page page
GENERAL INFORMATION LAMP ALIGNMENT SCREEN PREPARATION . . . . 5

HEADLAMP ALIGNMENT . . . . . . . . . . . . . . . . . . . 5 VEHICLE PREPARATION FOR HEADLAMP
SERVICE PROCEDURES ALIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FOG LAMP ADJUSTMENT . . . . . . . . . . . . . . . . . . 7 SPECIAL TOOLS
HEADLAMP ADJUSTMENT . . . . . . . . . . . . . . . . . 6 HEADLAMP ALIGNMENT . . . . . . . . . . . . . . . . . . . 7
GENERAL INFORMATION vehicle. Sight along the centerline of the vehicle

(from rear of vehicle forward) to verify accuracy of
HEADLAMP ALIGNMENT the line placement.
Headlamps can be aligned using the screen method (4) Rock vehicle side-to-side three times to allow
provided in this section. Alignment Tool C-4466-A or suspension to stabilize.
equivalent can also be used. Refer to instructions (5) Jounce front suspension three times by pushing
provided with the tool for proper procedures. downward on front bumper and releasing.
(6) Measure the distance from the center of head-
lamp lens to the floor. Transfer measurement to the
SERVICE PROCEDURES alignment screen (with tape). Use this line for
up/down adjustment reference.
LAMP ALIGNMENT SCREEN PREPARATION (7) Measure distance from the centerline of the
(1) Position vehicle on a level surface perpendicu- vehicle to the center of each headlamp being aligned.
lar to a flat wall 7.62 meters (25 ft) away from front Transfer measurements to screen (with tape) to each
of headlamp lens (Fig. 1). side of vehicle centerline. Use these lines for left/
(2) If necessary, tape a line on the floor 7.62 right adjustment reference.
meters (25 ft) away from and parallel to the wall.
(3) Measure from the floor up 1.27 meters (5 ft)
and tape a line on the wall at the centerline of the
8L - 6 LAMPS TJ
SERVICE PROCEDURES (Continued)
Fig. 1 Headlamp Alignment Screen—Typical

VEHICLE PREPARATION FOR HEADLAMP • Adjust the beam vertical position is 25 mm (1
in) downward from the lamp horizontal centerline.
ALIGNMENT
(4) Rotate the lower, inboard (left/right) adjust-
(1) Verify headlamp dimmer switch and high beam
ment screw (Fig. 2) until the headlamp beam pattern
indicator operation.
on the aiming screen/wall similar to the pattern in
(2) Correct defective components that could hinder
(Fig. 1).
proper headlamp alignment.
(5) Cover front of the headlamp that has been
(3) Verify proper tire inflation.
adjusted and adjust the other headlamp beam as
(4) Clean headlamp lenses.
instructed above.
(5) Verify that luggage area is not heavily loaded.
(6) Fuel tank should be FULL. Add 2.94 kg (6.5
lbs.) of weight over the fuel tank for each estimated
gallon of missing fuel.
HEADLAMP ADJUSTMENT
(1) Place headlamps on LOW beam.
(2) Cover front of the headlamp that is not being
adjusted.
(3) Turn the upper, outboard (up/down) adjustment
screw (Fig. 2) until the headlamp beam pattern on
screen/wall is similar to the pattern depicted in (Fig.
1).
NOTE: When using a headlamp aiming screen:
• Adjust the headlamps so that the beam horizon-

tal position is at 0. Fig. 2 Headlamp Adjustment Screws
TJ LAMPS 8L - 7
Fig. 3 Fog Lamp Alignment —Typical

FOG LAMP ADJUSTMENT (3) Tighten the nut attaching the fog lamp to the
Prepare an alignment screen. A properly aligned mounting bracket.
fog lamp will project a pattern on the alignment
screen 100 mm (4 in.) below the fog lamp centerline
SPECIAL TOOLS
and straight ahead (Fig. 3).
(1) Loosen the nut attaching the fog lamp to the
mounting bracket (Fig. 4).
HEADLAMP ALIGNMENT
(2) Move the fog lamp to adjust beam height.
Headlamp Aiming Kit C-4466–A
Fig. 4 Fog Lamp Adjustment

8L - 8 LAMPS TJ
LAMP BULB SERVICE
INDEX
page page
REMOVAL AND INSTALLATION FRONT PARK/TURN SIGNAL LAMP BULB . . . . . . 8

BACK-UP LAMP BULB . . . . . . . . . . . . . . . . . . . . . 9 HEADLAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . 8
CENTER HIGH MOUNTED STOP LAMP SIDE MARKER LAMP BULB . . . . . . . . . . . . . . . . . 8
(CHMSL) BULB . . . . . . . . . . . . . . . . . . . . . . . . . 9 TAIL/TURN SIGNAL/BACK-UP LAMP BULB . . . . . 8
DOME LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 UNDERHOOD LAMP BULB . . . . . . . . . . . . . . . . . 9
FOG LAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . . 8
REMOVAL AND INSTALLATION (2) Position the bulb/element in the reflector.

(3) Engage the bulb retainer.
HEADLAMP BULB (4) Position the reflector in the lamp housing.
The headlamp is a sealed unit. Refer to the Head- (5) Install the screws that attach the reflector to
lamp Removal/Installation procedure located in the the lamp housing.
Lamp Service section of this group.
FRONT PARK/TURN SIGNAL LAMP BULB
FOG LAMP BULB
REMOVAL
REMOVAL (1) Remove the park/turn signal lamp bulb socket
(1) Remove the screws that attach the reflector to via the underside of the fender.
the lamp housing. (2) Rotate the bulb socket one-third turn counter-
(2) Separate the reflector from the lamp housing. clockwise and separate it from the lamp housing.
(3) Squeeze the bulb retainer together to disengage (3) Pull the bulb straight out of the socket.
it from the reflector.
(4) Remove the bulb/element from the reflector INSTALLATION
(Fig. 1). (1) Install the bulb in the socket.
(5) Disconnect the electrical connector. (2) Install the bulb and socket in the lamp hous-
ing.
SIDE MARKER LAMP BULB

REMOVAL
(1) Remove side marker bulb socket via the under-
side of the fender. Rotate it one-third turn counter-
clockwise and separate it from the side marker lamp
housing.
(2) Remove the bulb from the socket by pulling it
straight outward.
INSTALLATION
(1) Install a replacement bulb in the socket.
(2) Install the bulb and socket in the side marker
lamp housing.
Fig. 1 Fog Lamp Bulb TAIL/TURN SIGNAL/BACK-UP LAMP BULB
INSTALLATION
REMOVAL
CAUTION: Do not touch the bulb glass with fingers (1) Remove the screws attaching the lens to the
or other oily surfaces. Reduced bulb life will result. tail lamp housing (Fig. 2).
(1) Connect the electrical connector. (2) Separate the lens from the tail lamp housing.
TJ LAMPS 8L - 9
(3) Push the bulb inward and rotate counter-clock-
wise.
(4) Remove the bulb from the lamp socket.
Fig. 3 CHMSL Bulb
Fig. 2 Lens Removal

INSTALLATION
(1) Install a replacement bulb in the lamp socket.
(2) Position the lens on the lamp housing.
(3) Install the screws. Tighten the screws securely.
BACK-UP LAMP BULB

The back-up lamp bulb is located with-in the tail
lamp. Refer to the Tail Lamp Bulb Removal/Installa-
tion procedure.
CENTER HIGH MOUNTED STOP LAMP

(CHMSL) BULB
Fig. 4 Underhood Lamp Lens
REMOVAL
(1) Remove the screws attaching the CHMSL lens
to the CHMSL (Fig. 3).
(2) Rotate the bulb socket one third turn counter-
clockwise and separate from lamp housing.
(3) Pull the bulb straight out of the socket.
INSTALLATION
(1) Install the bulb.
(2) Position the lens on the CHMSL and install the
screws.
UNDERHOOD LAMP BULB

REMOVAL
(1) Insert a small flat blade in the access slot
between the lamp base and lamp lens.
Fig. 5 Underhood Lamp Bulb
(2) Pry the lamp lens upward and remove the
lamp lens (Fig. 4). INSTALLATION
(3) Depress the bulb terminal inward (Fig. 5) to (1) Engage the replacement bulb wire loop to the
release the bulb. terminal closest to the lamp base wire connector.
8L - 10 LAMPS TJ
(2) Depress the opposite terminal inward and (2) Remove the lens from the lamp housing.
engage the remaining bulb wire loop. (3) Pull the bulb straight out to remove from the
(3) Position the lamp lens on the lamp base and bulb holder.
press into place.
DOME LAMP
SOUND BAR DOME LAMP BULB REMOVAL
(1) Insert a small flat blade between the lamp
housing and lamp lens. Carefully pry lamp lens to
disengage lens retaining tabs.
(2) Separate lens from lamp housing.
(3) Grasp bulb and pull from lamp.
SOUND BAR DOME LAMP BULB INSTALLATION

(1) Position bulb in lamp socket and press into
place.
(2) Position lamp lens on lamp housing and press
into place.
CARGO AREA DOME LAMP BULB REMOVAL Fig. 6 Cargo Area Dome Lamp
(1) Remove the dome/cargo lamp lens by squeezing CARGO AREA DOME LAMP BULB INSTALLATION
it at the lens at the top and bottom (Fig. 6). This will (1) Insert the replacement bulb in the bulb holder.
separate the lens retaining tabs from the lamp hous- (2) Position lens at the lamp housing and press
ing shoulders. into the housing until the retainer tabs are seated.
TJ LAMPS 8L - 11
LAMP SERVICE
INDEX
page page
REMOVAL AND INSTALLATION FRONT PARK/TURN SIGNAL LAMP . . . . . . . . . . 12

CENTER HIGH MOUNTED STOP LAMP HEADLAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
(CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 SIDE MARKER LAMP . . . . . . . . . . . . . . . . . . . . . 12
DOME LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 TAIL/STOP/TURN SIGNAL/BACK-UP LAMP . . . . 12
FOG LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 UNDERHOOD LAMP . . . . . . . . . . . . . . . . . . . . . 13

HEADLAMP
REMOVAL
(1) Remove the screws that attach the headlamp
bezel (Fig. 1).
(2) Remove the screws that attach the headlamp
retaining ring (Fig. 2).
(3) Disconnect the headlamp wire harness connec-
tor and remove the bulb from the bucket (Fig. 3).
Fig. 2 Headlamp Retaining Ring
Fig. 1 Headlamp Bezel

INSTALLATION
(1) Connect the wire harness connector and posi-
tion the bulb in the bucket.
(2) Position retaining ring on the headlamp bulb
and install screws. Fig. 3 Headlamp Connector
(3) Install the headlamp bezel. Tighten the screws
(2) Remove the nut attaching the fog lamp to the
securely.
front bumper.
(3) Separate the fog lamp from the bumper.
FOG LAMP
INSTALLATION
REMOVAL (1) Position the fog lamp on the bumper.
(1) Disconnect the fog lamp wire harness connec- (2) Install the nut attaching the fog lamp to the
tor. front bumper.
8L - 12 LAMPS TJ
(3) Connect the fog lamp wire harness connector. TAIL/STOP/TURN SIGNAL/BACK-UP LAMP
FRONT PARK/TURN SIGNAL LAMP REMOVAL
(1) From the underside of the vehicle, remove the
REMOVAL push-in fastener attaching the bottom rear edge of
(1) Remove the park/turn signal lamp housing the rear wheelhouse splash shield to the body.
screws (Fig. 4). (2) Pull the rear of the wheelhouse splash shield
(2) Separate the park/turn signal lamp housing away from the body and reach upward to disengage
from the fender. the tail lamp electrical connector.
(3) Rotate bulb socket one third turn counter-clock- (3) Remove the screws attaching the lens to the
wise and separate bulb socket from lamp. tail lamp housing.
(4) Remove the bolts attaching the tail lamp hous-
ing to the body (Fig. 5).
(5) Separate the lamp housing from the body.
Fig. 4 Park/Turn Signal Lamp

INSTALLATION
(1) Install the bulb socket in the lamp housing.
(2) Position the park/turn signal lamp housing in Fig. 5 Tail Lamp Housing
the fender. INSTALLATION
(3) Install the park/turn signal lamp housing (1) Engage the electrical connector.
screws. (2) Install the push-in fastener attaching the bot-
tom rear edge of the rear wheelhouse splash shield to
SIDE MARKER LAMP the body.
(3) Position the lamp housing on the body.
REMOVAL (4) Install the bolts attaching the tail lamp hous-
(1) From underside of the fender, remove nut ing to the body.
attaching marker lamp to fender. (5) Install the screws attaching the lens to the tail
(2) Separate lamp from fender. lamp housing.
(3) Rotate bulb socket one-third turn counter-clock-
wise and separate socket from lamp housing. CENTER HIGH MOUNTED STOP LAMP
(CHMSL)
INSTALLATION
(1) Position bulb socket in lamp housing and REMOVAL
rotate bulb socket one-third turn clockwise.
(2) Position lamp in fender. NOTE: It may be necessary to remove spare tire.
(3) Install nut attaching marker lamp to fender.
(1) Remove screws attaching CHMSL lamp/bracket
to spare tire carrier bracket.
(2) Disengage CHMSL wire harness from retaining
clips.
(3) Remove cover from CHMSL contact buttons.
TJ LAMPS 8L - 13
(4) Carefully pull wire harness terminal ends from (4) Install the attaching screw through the lamp
contact buttons (Fig. 6). flange and into the hood panel (Fig. 7). Tighten the
(5) Route wire harness through tailgate and sepa- screw securely.
rate CHMSL from vehicle. (5) Fold lamp housing over and firmly press onto
base to snap into place.
(6) Connect the wire harness connector to the
lamp.
Fig. 7 Underhood Lamp

DOME LAMP
Fig. 6 CHMSL Contact Buttons
SOUND BAR DOME LAMP REMOVAL
INSTALLATION (1) Insert a small flat blade between the lamp
(1) Position CHMSL lamp/bracket on spare tire housing and lamp lens. Carefully pry lamp lens from
carrier bracket and install screws. the lamp housing.
(2) Route wire harness through tailgate. (2) Separate lens from lamp.
(3) Install wire harness terminal ends onto contact (3) Remove the screws attaching the lamp to the
buttons. sound bar (Fig. 8).
(4) Install cover over CHMSL contact buttons. (4) Disengage lamp electrical connector.
(5) Position CHMSL wire harness into CHMSL
bracket retaining clips and engage clips. SOUND BAR DOME LAMP INSTALLATION
(1) Engage lamp electrical connector.
UNDERHOOD LAMP (2) Position lamp in sound bar.
(3) Install the screws attaching the lamp to the
REMOVAL sound bar.
(1) Disconnect the wire harness connector from the (4) Position lamp lens on lamp housing and press
lamp. into place.
(2) Remove lamp lens.
(3) Remove bulb. CARGO AREA DOME LAMP REMOVAL
(4) Remove screw attaching underhood lamp to the Vehicles equipped with a hardtop have a dome
inner hood panel. lamp located above the rear window lift glass.
(5) Separate underhood lamp from vehicle. (1) Remove the dome/cargo lamp lens by squeezing
it at the top and bottom. This will separate the lens
INSTALLATION retaining tabs from the lamp housing shoulders.
(1) Install bulb. (2) Remove the lens from the lamp housing.
(2) Install lamp lens. (3) Remove the bulb.
(3) Position the underhood lamp flange on the (4) Remove the screws that attach the lamp to the
hood inner panel. hardtop.
(5) Separate the lamp from the hardtop.
8L - 14 LAMPS TJ
CARGO AREA DOME LAMP INSTALLATION
(1) Connect the lamp wire connector.
(2) Position the lamp in the hardtop.
(3) Install the screws that attach the lamp to the
hardtop.
(4) Install the bulb.
(5) Position the lens on the lamp housing and
press into place.
Fig. 8 Sound Bar Dome Lamp

(6) Disconnect the lamp wire connector.
TJ LAMPS 8L - 15
LAMP SYSTEMS
INDEX
page page
GENERAL INFORMATION REMOVAL AND INSTALLATION

DAYTIME RUNNING LIGHTS (CANADA ONLY) . . 15 DAYTIME RUNNING LAMP (DRL) MODULE . . . . 15
GENERAL INFORMATION
DAYTIME RUNNING LIGHTS (CANADA ONLY)
The Daytime Running Lights (Headlamps) System
is installed on vehicles manufactured for sale in Can-
ada only. The headlamps are illuminated when the
ignition switch is turned to the ON position. The
DRL module receives a vehicle-moving signal from
the vehicle speed sensor. This provides a constant
headlamps-on condition as long as the vehicle is
moving. The lamps are illuminated at less than 50
percent of normal intensity.

DAYTIME RUNNING LAMP (DRL) MODULE
REMOVAL
(1) Disconnect the wire harness connector from the
module.
(2) Remove the screws that attach the module to
the cowl (Fig. 1). Fig. 1 DRL Module
(3) Separate the module from the vehicle. (3) Connect the wire harness connector to the mod-
ule.
INSTALLATION
(1) Position the DRL module on the cowl.
(2) Install the screws.
8L - 16 LAMPS TJ
BULB APPLICATION
INDEX
page page
SPECIFICATIONS INTERIOR LAMPS . . . . . . . . . . . . . . . . . . . . . . . 16

EXTERIOR LAMPS . . . . . . . . . . . . . . . . . . . . . . . 16
SPECIFICATIONS INTERIOR LAMPS

EXTERIOR LAMPS CAUTION: Do not use bulbs that have a higher can-
dle power than the bulb listed in the Bulb Applica-
CAUTION: Do not use bulbs that have a higher can- tion Table. Damage to lamp can result.
dle power than the bulb listed in the Bulb Applica-
tion Table. Damage to lamp can result. Do not touch Service procedures for most of the lamps in the
halogen bulbs with fingers or other oily surfaces. instrument panel, Instrument cluster and switches
Bulb life will be reduced. are located in Group 8E, Instrument Panel and
Gauges. Some components have lamps that can only
The following Bulb Application Table lists the lamp be serviced by an Authorized Service Center (ASC)
title on the left side of the column and trade number after the component is removed from the vehicle.
or part number on the right. The following Bulb Application Table lists the lamp
title on the left side of the column and trade number
LAMP BULB or part number on the right.
Back-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1156
Center High Mounted Stoplamp . . . . . 921 or W16W LAMP BULB
Fog lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H3 Dome/Cargo (Hard Top) . . . . . . . . . . . . . . . . . 212–2
Front Side Marker . . . . . . . . . . . . . . . . 168 or W3W Dome (Sound Bar) . . . . . . . . . . . . . . . . . . . . . . . 912
Headlamp/Sealed Beam . . . . . . . . . . . . . . . . . H6024 Under Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
Park/Turn Signal . . . . . . . . . . . . . . . . . . . . . . . 3157 Underpanel Courtesy . . . . . . . . . . . . . . . . . . . . . 906
Tail/Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1157
TJ LAMPS 8L - 1
LAMPS
CONTENTS
page page
BULB APPLICATION . . . . . . . . . . . . . . . . . . . . . . 11 LAMP DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . 1

LAMP BULB SERVICE . . . . . . . . . . . . . . . . . . . . . 5 LAMP SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
LAMP DIAGNOSIS
INDEX
page page
GENERAL INFORMATION DIAGNOSIS AND TESTING

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . 1 DIAGNOSTIC PROCEDURES . . . . . . . . . . . . . . . . 2
HEADLAMP LEVELING MOTOR . . . . . . . . . . . . . . 1
GENERAL INFORMATION Do not use bulbs with higher candle power than
indicated in the Bulb Application Table at the end of
GENERAL INFORMATION this group. Damage to lamp can result.
Each vehicle is equipped with varies lamp assem- Do not use fuses, circuit breakers or relays hav-
blies. A good ground is necessary for proper lighting ing greater amperage value than indicated on the
operation. Grounding is provided by the lamp socket fuse panel or in the Owners Manual.
when it comes in contact with the metal body, or
When it necessary to remove components to service
through a separate ground wire.
another, it should not be necessary to apply excessive
When changing lamp bulbs check the sockets for
force or bend a component to remove it. Before dam-
corrosion. If corrosion is present, clean it with a wire
aging a trim component, verify hidden fasteners or
brush and coat the inside of the socket lightly with
captured edges are not holding the component in
Mopar Multi-Purpose Grease or equivalent.
place.
SAFETY PRECAUTIONS
HEADLAMP LEVELING MOTOR
WARNING: EYE PROTECTION SHOULD BE USED This vehicle is equipped with a remote headlamp
WHEN SERVICING GLASS COMPONENTS. PER- leveling system. This system allows the driver to
SONAL INJURY CAN RESULT. adjust the vertical headlamp aim from the interior of
the vehicle to compensate for passenger or cargo
load. A headlamp leveling switch is located in the
CAUTION: Do not touch the glass of halogen bulbs instrument panel and controls the headlamp leveling
with fingers or other possibly oily surfaces, motor found on the back of the head lamp assembly.
reduced bulb life can result.
8L - 2 LAMPS TJ
DIAGNOSIS AND TESTING tions, charging system, headlamp bulbs, wire

connectors, relay, high beam dimmer switch and head-
DIAGNOSTIC PROCEDURES lamp switch. Refer to Group 8W, Wiring Diagrams, for
When a vehicle experiences problems with the head- component locations and circuit information.
lamp system, verify the condition of the battery connec-
HEADLAMP DIAGNOSIS
HEADLAMPS ARE 1. Loose or corroded battery cables. 1. Clean and secure battery cable clamps
DIM WITH ENGINE and posts.
IDLING OR
IGNITION TURNED 2. Loose or worn alternator drive belt. 2. Adjust or replace alternator drive belt.
OFF
Group 8A.
Group 8A.
HEADLAMP BULBS 1. Charging system output too high. 1. Test and repair charging system. Refer to
BURN OUT Group 8A.
FREQUENTLY
2. Loose or corroded terminals or splices in 2. Inspect and repair all connectors and
circuit. splices. Refer to Group 8W.
HEADLAMPS ARE 1. Charging system output too low. 1. Test and repair charging system. Refer to
DIM WITH ENGINE Group 8A.
RUNNING ABOVE 2. Poor lighting circuit Z1-ground. 2. Test for voltage drop across Z1-ground
IDLE locations. Refer to Group 8W.
3. High resistance in headlamp circuit. 3. Test amperage draw of headlamp circuit.
HEADLAMPS 1. Poor lighting circuit Z1-ground. 1. Test for voltage drop across Z1-ground
FLASH RANDOMLY locations, refer to Group 8W.
2. High resistance in headlamp circuit. 2. Test amperage draw of headlamp circuit.
3. Loose or corroded terminals or splices in 3. Inspect and repair all connectors and
circuit. splices. Refer to Group 8W.
HEADLAMPS DO 1. No voltage to headlamps. 1. Repair open headlamp circuit. Refer to

NOT ILLUMINATE Group 8W.
2. No Z1-ground at headlamps. 2. Repair circuit ground. Refer to Group
8W.
3. Faulty headlamp switch. 3. Replace headlamp switch.
4. Faulty headlamp dimmer (multi-function) 4. Replace multi-function switch.
switch.
5. Broken connector terminal or wire splice 5. Repair connector terminal or wire splice.
in headlamp circuit.
7. Body controller malfunction. 7. Refer to appropriate body controller
diagnostics.
TJ LAMPS 8L - 3
FOG LAMP DIAGNOSIS
FOG LAMPS ARE DIM 1. Loose or corroded battery cables. 1. Clean and secure battery cable clamps
WITH ENGINE IDLING OR and posts.
IGNITION TURNED OFF. 2. Loose or worn alternator drive 2. Adjust or replace alternator drive belt.
belt.
Group 8A.
Group 8A.
FOG LAMP BULBS BURN 1. Charging system output too high. 1. Test and repair charging system. Refer to
OUT FREQUENTLY Group 8A.

FOG LAMPS ARE DIM 1. Charging system output too low. 1. Test and repair charging system. Refer to
ABOVE IDLE 2. Poor lighting circuit Z1-ground. 2. Test for voltage drop across Z1-ground
FOG LAMPS FLASH 1. Poor lighting circuit Z1-ground. 1. Test for voltage drop across Z1-ground
RANDOMLY locations. Refer to Group 8W.
FOG LAMPS DO NOT 1. Blown fuse for fog lamp. 1. Replace fuse. Refer to Group 8W.
ILLUMINATE 2. No Z1-ground at fog lamps. 2. Repair circuit ground. Refer to Group
8W.
splice in fog lamp circuit.
8L - 4 LAMPS TJ
HEADLAMP LEVELING MOTOR DIAGNOSIS
ONE MOTOR DOES NOT 1. Poor connection at motor. 1. Secure connector on motor.
OPERATE
2. No voltage at motor. 2. Repair circuit. Refer to Group 8W,
Wiring.
3. Defective motor. 3. Replace motor.
BOTH MOTORS DO NOT 1. No voltage at headlamp leveling 1. Repair circuit or replace fuse. Refer to
OPERATE switch. Group 8W, Wiring.
2. No voltage at both motors. 2. Repair circuit or replace fuse. Refer to
Group 8W, Wiring.
3. Poor connection at motors. 3. Secure connectors on motors.
4. Both motors defective. 4. Replace motors.
TJ LAMPS 8L - 5
LAMP BULB SERVICE
INDEX
page page
REMOVAL AND INSTALLATION HEADLAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . 5

CENTER HIGH MOUNTED STOP LAMP LICENSE PLATE LAMP BULB . . . . . . . . . . . . . . . 7
(CHMSL) BULB . . . . . . . . . . . . . . . . . . . . . . . . . 7 REAR FOG LAMP BULB . . . . . . . . . . . . . . . . . . . 7
CITYLIGHT LAMP BULB . . . . . . . . . . . . . . . . . . . . 6 TAIL LAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . . 6

HEADLAMP BULB
REMOVAL
(1) Release the hood latches and open hood.
(2) Disconnect the headlamp wire harness connec-
tors.
(3) Remove the headlamp bezel retaining screws
and bezel (Fig. 1).
(4) Remove the headlamp retaining ring screws
and retaining ring (Fig. 2).
(5) Remove the headlamp from vehicle.
(6) Remove rubber seal boot (Fig. 3).
(7) Disengage wire retaining ring from headlamp
(Fig. 4).
(8) Pull the headlamp bulb from back of headlamp Fig. 2 Headlamp Retaining Ring
assembly (Fig. 5).
Fig. 3 Headlamp Rubber Seal Boot

8L - 6 LAMPS TJ
Fig. 4 Headlamp Bulb Retaining Ring
Fig. 6 Citylight Lamp Bulb Housing
Fig. 5 Headlamp Bulb

INSTALLATION
(1) Perform the removal procedure in reverse
order. Fig. 7 Citylight Lamp Bulb
CITYLIGHT LAMP BULB

REMOVAL
(1) Remove the headlamp from the vehicle. Refer
to the headlamp Removal/Installation procedure
located in this group.
(2) Remove rubber seal boot.
(3) Remove citylight lamp bulb housing from the
headlamp (Fig. 6).
(4) Remove citylight bulb from housing.
Installation
order.
TAIL LAMP BULB

REMOVAL
(1) Remove the tail lamp lense retaining screws
Fig. 8 Tail Lamp Lense
(Fig. 8).
(2) Separate the tail lamp lense from the tail lamp INSTALLATION
housing. (1) Perform the removal procedure in reverse
(3) Remove the tail lamp bulb from the bulb socket order.
(Fig. 9).
TJ LAMPS 8L - 7
Fig. 9 Tail Lamp Bulbs Fig. 11 REAR FOG LAMP BULB

REAR FOG LAMP BULB INSTALLATION
REMOVAL order.
(1) Remove the rear fog lamp lense attaching
screws and lense (Fig. 10). LICENSE PLATE LAMP BULB
(2) Remove the bulb from the fog lamp socket (Fig.
11). REMOVAL
(1) Remove the license plate lamp lense attaching
screws and lense.
(2) Remove the bulb from the socket.
INSTALLATION
order.

(CHMSL) BULB
REMOVAL
(1) Remove the screws attaching the center high
mounted stop lamp (CHMSL) lense assembly to the
housing.
(2) Separate the CHMSL lense assembly from the
housing.
INSTALLATION
Fig. 10 REAR FOG LAMP LENSE (1) Perform the removal procedure in reverse
order.
8L - 8 LAMPS TJ
LAMP SERVICE
INDEX
page page
REMOVAL AND INSTALLATION HEADLAMP LEVELING MOTOR . . . . . . . . . . . . . . 8

CENTER HIGH MOUNTED STOP LAMP REAR FOG LAMP . . . . . . . . . . . . . . . . . . . . . . . 10
(CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 TAIL LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HEADLAMP ASSEMBLY . . . . . . . . . . . . . . . . . . . . 8

HEADLAMP ASSEMBLY
REMOVAL
(1) Remove the headlamp bezel attaching screws
(Fig. 1).
(2) Remove the headlamp assembly retaining ring
attaching screws (Fig. 2).
(3) Disconnect the headlamp assembly electrical
connectors and remove the headlamp assembly from
the bucket.
Fig. 2 Headlamp Retaining Ring

(5) Pull the leveling motor from the headlamp
housing.
(6) Separate the leveling motor from the headlamp
housing (Fig. 5).
NOTE: The headlamp leveling motor arm is

snapped into the headlamp housing very securely.
Use a firm, steady pull to disengage motor arm
from the headlamp housing.

Installation
(1) Perform the removal procedure in reverse order.
HEADLAMP LEVELING MOTOR

REMOVAL
(1) Remove the headlamp bezel attaching screws
and bezel (Fig. 3).
(2) Disconnect the headlamp and headlamp level-
ing motor electrical connectors.
(3) Remove the headlamp housing attaching
screws (Fig. 4).
(4) Rotate leveling motor one quarter turn counter-
clockwise. Fig. 3 Headlamp Bezel
TJ LAMPS 8L - 9
(2) Remove the tail lamp housing attaching bolts
(Fig. 7).
(3) Separate the lamp housing from the body.
(4) Disconnect the tail lamp electrical connector
and remove tail lamp housing.
Fig. 4 Headlamp Housing
Fig. 6 Tail Lamp Lense
Fig. 7 Tail Lamp Housing

Fig. 5 Headlamp Leveling Motor
INSTALLATION
INSTALLATION (1) Perform the removal procedure in reverse
(1) Perform the removal procedure in reverse order.
order.
TAIL LAMP
REMOVAL
(1) Remove the tail lamp lense attaching screws
and lense (Fig. 6).
8L - 10 LAMPS TJ

(CHMSL)
REMOVAL
NOTE: It may be necessary to remove the spare
tire.
(1) Remove the CHMSL housing to CHMSL

bracket attaching screws.
(2) Disconnect the CHMSL wire harness from the
retaining clips.
(3) Remove the cover from the CHMSL contact
buttons.
(4) Carefully pull the wire harness terminal ends
from the contact buttons (Fig. 8).
(5) Route wire harness through tailgate and sepa-
rate CHMSL from vehicle.
INSTALLATION
order.
Fig. 8 CHMSL Assembly
REAR FOG LAMP
REMOVAL
(1) Remove the rear fog lamp attaching screw (Fig.
9).
(2) Disconnect the rear fog lamp electrical connec-
tor.
INSTALLATION
order.
Fig. 9 Rear Fog Lamp

TJ LAMPS 8L - 11
BULB APPLICATION
INDEX
page page
GENERAL INFORMATION INTERIOR LAMPS . . . . . . . . . . . . . . . . . . . . . . . 11

GENERAL INFORMATION . . . . . . . . . . . . . . . . . 11
SPECIFICATIONS
EXTERIOR LAMPS . . . . . . . . . . . . . . . . . . . . . . . 11
GENERAL INFORMATION INTERIOR LAMPS

Service procedures for most of the lamps in the
GENERAL INFORMATION instrument panel, Instrument cluster and switches
(1) The following bulb Application tables lists the are located in Group 8E, Instrument panel and
lamp title on the left side of the column and trade Gauges. Some components have lamps than can only
number on the right. be serviced by an Authorized Service Center (ASC)
after the component is removed from the vehicle.
CAUTION: Do not use bulbs that have a higher can- Contact a local dealer for location of nearest ASC.
dle power the bulb listed in the Bulb Application
Table. Damage to lamp can result. Do not touch LAMP BULB
halogen bulbs with fingers or other oily surfaces. ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PC74
Bulb life will be reduced. Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PC194
Brake Warning System Indicator . . . . . . . . . PC194
Cigar Lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
SPECIFICATIONS Climate Controls . . . . . . . . . . . . . . . . . . . . . . . . 203
Console Gear Selector . . . . . . . . . . . . . . . . . . . . 161
EXTERIOR LAMPS Dome Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 912
High Beam Indicator . . . . . . . . . . . . . . . . . . . PC194
LAMP BULB Rear Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 912
Back-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P21W Seat Belt Indicator . . . . . . . . . . . . . . . . . . . . . PC74
Center High Mounted Stop . . . . . . . . . . . . . . W16W Service Engine Soon . . . . . . . . . . . . . . . . . . . PC194
Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4 Turn Signal Indicator . . . . . . . . . . . . . . . . . . PC194
License Plate . . . . . . . . . . . . . . . . . . . . . . . . . . W5W Underhood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Front Turn Signal . . . . . . . . . . . . . . . . . . . . P27/7W
Tail/Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . P21/5W
Rear Turn Signal . . . . . . . . . . . . . . . . . . . . . . P21W
Rear Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . P21W
Citylight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T4W
Side Repeater . . . . . . . . . . . . . . . . . . . . . . . . . W5W
TJ PASSIVE RESTRAINT SYSTEMS 8M - 1
PASSIVE RESTRAINT SYSTEMS

CONTENTS
page page
DESCRIPTION AND OPERATION CLOCKSPRING . . . . . . . . . . . . . . . . . . . . . . . . . 15

AIRBAG CONTROL MODULE . . . . . . . . . . . . . . . 4 DRIVER SIDE AIRBAG MODULE . . . . . . . . . . . . 6
AIRBAG SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . 1 DRIVER SIDE AIRBAG MODULE
CLOCKSPRING . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TRIM COVER . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DRIVER SIDE AIRBAG MODULE . . . . . . . . . . . . 2 PASSENGER SIDE AIRBAG DOOR . . . . . . . . . . 11
PASSENGER SIDE AIRBAG MODULE . . . . . . . . . 3 PASSENGER SIDE AIRBAG MODULE . . . . . . . . 10
PASSENGER SIDE AIRBAG PASSENGER SIDE AIRBAG
ON/OFF SWITCH . . . . . . . . . . . . . . . . . . . . . . . 3 ON/OFF SWITCH . . . . . . . . . . . . . . . . . . . . . . 12
DIAGNOSIS AND TESTING ADJUSTMENTS
AIRBAG SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . 5 CLOCKSPRING CENTERING . . . . . . . . . . . . . . . 17
SERVICE PROCEDURES SPECIAL TOOLS
AIRBAG SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . 5 PASSIVE RESTRAINT SYSTEMS . . . . . . . . . . . 18
AIRBAG CONTROL MODULE . . . . . . . . . . . . . . 14
DESCRIPTION AND OPERATION plete service information for the other airbag system
components can be located as follows:
AIRBAG SYSTEM • Refer to Instrument Cluster in the proper sec-
tion of Group 8E - Instrument Panel Systems for
DESCRIPTION complete service information for the airbag indicator
A dual front airbag system is standard factory-in- lamp.
stalled safety equipment on this model. The primary • Refer to Knee Blocker in the Removal and
passenger restraints in this vehicle are the standard Installation section of Group 8E - Instrument Panel
equipment factory-installed seat belts, which require Systems for complete service information on the
active use by the vehicle occupants. The airbag sys- driver side knee blocker.
tem is a supplemental passive restraint that was • Refer to Glove Box in the Removal and Instal-
designed and is intended to enhance the protection lation section of Group 8E - Instrument Panel Sys-
for the front seat occupants of the vehicle only when tems for complete service information on the
used in conjunction with the seat belts. See the own- passenger side knee blocker.
er’s manual in the vehicle glove box for more infor- • Refer to Airbag System in the Contents of
mation on the features, use and operation of all of Group 8W - Wiring Diagrams for complete service
the factory-installed passenger restraints, including information and circuit diagrams for the airbag sys-
the airbag system. tem wiring components.
The dual front airbag system consists of the follow- See the proper Diagnostic Procedures manual to
ing components: test or diagnose a problem with any component of
• Airbag Control Module (ACM) the airbag system.
• Airbag indicator lamp
• Clockspring OPERATION
• Driver and passenger side airbag modules The airbag system electrical circuits are continu-
(including the airbag inflators) ously monitored and controlled by a microprocessor
• Driver and passenger side knee blockers and software contained within the Airbag Control
• Passenger side airbag on/off switch Module (ACM). The ACM also contains an impact
• Wire harness and connections. sensor and a safing sensor, which are monitored by
This group provides complete service information the ACM to determine when an impact occurs that is
for the ACM, both airbag modules, the clockspring, severe enough to require airbag system protection.
and the passenger side airbag on/off switch. Com- When a frontal impact is severe enough, the ACM
8M - 2 PASSIVE RESTRAINT SYSTEMS TJ
signals the inflator units of both airbag modules to GAS PRESSURIZED TO OVER 2500 PSI. DO NOT
deploy the airbags. ATTEMPT TO DISMANTLE AN AIRBAG MODULE OR
An airbag indicator lamp in the instrument cluster TAMPER WITH ITS INFLATOR. DO NOT PUNCTURE,
lights for about seven seconds as a bulb test, each INCINERATE, OR BRING INTO CONTACT WITH
time the ignition switch is turned to the On or Start ELECTRICITY. DO NOT STORE AT TEMPERATURES
positions. Following the bulb test, the airbag indica- EXCEEDING 93° C (200° F).
tor lamp is turned on or off by the ACM to indicate • REPLACE AIRBAG SYSTEM COMPONENTS
the status of the airbag system. If the airbag indica- ONLY WITH PARTS SPECIFIED IN THE CHRYSLER
tor lamp comes on at any time other than during the MOPAR PARTS CATALOG. SUBSTITUTE PARTS
bulb test, it indicates that there is a problem in the MAY APPEAR INTERCHANGEABLE, BUT INTERNAL
airbag system circuits. Such a problem may cause DIFFERENCES MAY RESULT IN INFERIOR OCCU-
the airbags not to deploy when required, or to deploy PANT PROTECTION.
when not required. • THE FASTENERS, SCREWS, AND BOLTS ORIG-
The driver side airbag module includes an inflat- INALLY USED FOR THE AIRBAG SYSTEM COMPO-
able airbag and an inflator unit behind a trim cover NENTS HAVE SPECIAL COATINGS AND ARE
in the hub area of the steering wheel. The passenger SPECIFICALLY DESIGNED FOR THE AIRBAG SYS-
side airbag module includes a second inflatable air- TEM. THEY MUST NEVER BE REPLACED WITH ANY
bag and an inflator unit behind an airbag door in the SUBSTITUTES. ANY TIME A NEW FASTENER IS
instrument panel above the glove box. NEEDED, REPLACE IT WITH THE CORRECT FAS-
During a frontal vehicle impact, the knee blockers TENERS PROVIDED IN THE SERVICE PACKAGE OR
work in concert with properly adjusted seat belts to SPECIFIED IN THE CHRYSLER MOPAR PARTS CAT-
restrain the driver and front seat passenger in the ALOG.
proper position for an airbag deployment. The knee • WHEN A STEERING COLUMN HAS AN AIRBAG
blockers also work to absorb and distribute the crash MODULE ATTACHED, NEVER PLACE THE COLUMN
energy from the driver and front seat passenger to ON THE FLOOR OR ANY OTHER SURFACE WITH
the structure of the instrument panel. The driver THE STEERING WHEEL OR AIRBAG MODULE FACE
side knee blocker is a stamped metal reinforcement DOWN.
located behind the instrument panel steering column
opening cover. The passenger side knee blocker is
integral to the glove box door. DRIVER SIDE AIRBAG MODULE
Following are general descriptions of the major
components in the airbag system. DESCRIPTION
The driver side airbag module protective trim cover
WARNING: is the most visible part of the driver side airbag sys-
• THE AIRBAG SYSTEM IS A SENSITIVE, COM- tem. The driver side airbag module is mounted
PLEX ELECTROMECHANICAL UNIT. BEFORE directly to the steering wheel. Located under the air-
ATTEMPTING TO DIAGNOSE OR SERVICE ANY AIR- bag module trim cover are the horn switch, the
BAG SYSTEM OR RELATED STEERING WHEEL, folded airbag cushion, and the airbag cushion sup-
STEERING COLUMN, OR INSTRUMENT PANEL porting components. The resistive membrane-type
COMPONENTS YOU MUST FIRST DISCONNECT horn switch is secured with heat stakes to the inside
AND ISOLATE THE BATTERY NEGATIVE (GROUND) surface of the airbag module trim cover, between the
CABLE. THEN WAIT TWO MINUTES FOR THE SYS- trim cover and the folded airbag cushion.
TEM CAPACITOR TO DISCHARGE BEFORE FUR- The driver side airbag module cannot be repaired,
THER SYSTEM SERVICE. THIS IS THE ONLY SURE and must be replaced if deployed or in any way dam-
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE aged. The driver side airbag module trim cover and
TO DO THIS COULD RESULT IN ACCIDENTAL AIR- the horn switch are available as a unit for service
BAG DEPLOYMENT AND POSSIBLE PERSONAL replacement.
INJURY.
• THE DRIVER SIDE AIRBAG MODULE INFLATOR OPERATION
ASSEMBLY CONTAINS SODIUM AZIDE AND POTAS- The driver side airbag module includes a stamped
SIUM NITRATE. THESE MATERIALS ARE POISON- metal housing to which the cushion and an inflator
OUS AND EXTREMELY FLAMMABLE. CONTACT unit are attached and sealed. The conventional pyro-
WITH ACID, WATER, OR HEAVY METALS MAY PRO- technic-type inflator assembly is mounted to studs on
DUCE HARMFUL AND IRRITATING GASES (SODIUM the back of the airbag module housing. The inflator
HYDROXIDE IS FORMED IN THE PRESENCE OF seals the hole in the airbag cushion so it can dis-
MOISTURE) OR COMBUSTIBLE COMPOUNDS. THE charge the gas it produces directly into the cushion
PASSENGER AIRBAG MODULE CONTAINS ARGON
when supplied with the proper electrical signal. Fol- porous fabric material used on each end panel of the
lowing an airbag deployment, the airbag cushion airbag cushion.
quickly deflates by venting this gas towards the The molded plastic passenger side airbag door is
instrument panel through the porous fabric material secured to the instrument panel at the upper and
used on the steering wheel side of the airbag cushion. lower flanges with screws. A stamped metal bracket
The protective trim cover is fitted to the front of located on the back side of the airbag door is secured
the airbag module and forms a decorative cover in to the instrument panel armature with one screw on
the center of the steering wheel. The inside of the each end, and serves as the hinge for the door upon
trim cover has locking blocks molded into it that an airbag deployment. The airbag door has predeter-
engage a lip on the airbag module metal housing. mined breakout lines concealed beneath its decora-
Two stamped metal retainers then fit over the infla- tive cover. Upon airbag deployment, the airbag door
tor mounting studs on the back of the airbag module will split at the breakout lines and the door will fold
housing and are engaged in slots on the inside of the back over the top of the instrument panel, out of the
cover, securely locking the trim cover into place. The way.
trim cover will split at predetermined breakout lines,
then fold back out of the way along with the horn PASSENGER SIDE AIRBAG ON/OFF SWITCH
switch upon airbag deployment.
DESCRIPTION
PASSENGER SIDE AIRBAG MODULE A passenger side airbag on/off switch, which is
located on the forward end of the floor console (both
DESCRIPTION full and mini versions), allows the passenger side air-
The passenger side airbag door on the instrument bag system to be disabled when certain child
panel above the glove box is the most visible part of restraint devices are being used in the right front
the passenger side airbag system. Located under the seating position. The passenger side airbag on/off
airbag door are the passenger side airbag cushion switch is equipped with a key actuator so that the
and the airbag cushion supporting components. switch position can only be changed using an ignition
The passenger side airbag module includes a key. When the ignition switch is in the On position
stamped metal housing within which the cushion and and the passenger side airbag system is disabled, a
inflator are mounted and sealed. The airbag housing Light-Emitting Diode (LED) illuminates an Off indi-
has three stamped metal mounting brackets spot cator lamp on the face plate of the switch.
welded to it. The mounting brackets at the top and The passenger side airbag on/off switch cannot be
at the lower rear of the airbag module secure the adjusted or repaired and, if faulty or damaged, the
module to the instrument panel armature. The switch assembly must be replaced. The switch bezel
stamped metal mounting bracket at the lower front is available for service replacement.
of the housing secures the passenger side airbag
module to two studs on the dash panel, behind the OPERATION
glove box. A plastic end bracket encloses the inboard To actuate the passenger side airbag on/off switch,
end of the housing and retains the wire harness con- insert the ignition key in the switch key actuator.
nector for the inflator. The switch key actuator is then rotated with the
Following a passenger side airbag deployment, the ignition key to its clockwise stop (the key actuator
passenger side airbag module, the passenger side air- slot will be aligned with the Off indicator lamp) to
bag door and the instrument panel assembly must be disable the passenger side airbag system. When the
replaced. The passenger side airbag module cannot switch key actuator is rotated with the ignition key
be repaired, and must be replaced if deployed or in to its counterclockwise stop (the key actuator slot
any way damaged. The passenger side airbag door is will be in a vertical position), the Off indicator lamp
available as a separate service item. will be extinguished and the passenger side airbag
system will be enabled.
OPERATION
The hybrid-type inflator assembly includes a small WARNING: THE KEY MUST ALWAYS BE REMOVED
canister of highly compressed argon gas. The inflator FROM THE PASSENGER SIDE AIRBAG ON/OFF
seals the hole in the airbag cushion so it can dis- SWITCH KEY ACTUATOR AFTER THE SWITCH HAS
charge the gas it produces directly into the cushion BEEN USED. NEVER LEAVE A KEY IN THE SWITCH
when supplied with the proper electrical signal. Fol- KEY ACTUATOR. FAILURE TO OBSERVE THIS
lowing an airbag deployment, the airbag cushion WARNING COULD RESULT IN ACCIDENTAL,
quickly deflates by venting this gas through the INCOMPLETE OR IMPROPER AIRBAG DEPLOY-
MENT AND POSSIBLE OCCUPANT INJURIES.
AIRBAG CONTROL MODULE protection in a severe secondary impact, if the initial

impact has damaged or disconnected the battery, but
DESCRIPTION was not severe enough to deploy the airbags.
The Airbag Control Module (ACM) is secured with
screws to a mounting bracket that is secured with CLOCKSPRING
four screws onto the floor panel transmission tunnel
below the instrument panel and forward of the center DESCRIPTION
floor console in the passenger compartment of the The clockspring assembly is secured with two inte-
vehicle. The ACM contains an electronic microproces- gral plastic latches onto the steering column lock
sor, an electronic impact sensor, an electromechanical housing near the top of the steering column behind
safing sensor, and an energy storage capacitor. the steering wheel. The clockspring is used to main-
The ACM is serviced as a unit with the mounting tain a continuous electrical circuit between the fixed
bracket. The ACM cannot be repaired or adjusted clockspring wire harness on the steering column and
and, if damaged or faulty, the ACM and mounting several electrical components that rotate with the
bracket unit must be replaced. steering wheel. The rotating components include the
driver side airbag module, the horn switch and, if the
OPERATION vehicle is so equipped, the vehicle speed control
The microprocessor in the ACM contains the airbag switches.
system logic. The airbag system logic includes The clockspring cannot be repaired. If the clock-
On-Board Diagnostics (OBD), and the ability to com- spring is faulty, damaged, or if the driver side airbag
municate with the instrument cluster circuitry over has been deployed, the clockspring must be replaced.
the Chrysler Collision Detection (CCD) data bus to
control the airbag indicator lamp. The microprocessor OPERATION
continuously monitors all of the airbag system elec- The clockspring assembly consists of a plastic case
trical circuits to determine the system readiness. If which contains a flat, ribbon-like, electrically conduc-
the ACM detects a monitored system fault, it sends tive tape that winds and unwinds like a clockspring
messages to the instrument cluster over the CCD with the steering wheel rotation. The electrically con-
data bus to turn on the airbag indicator lamp. Refer ductive tape consists of several fine gauge copper
to Instrument Cluster in the proper section of wire leads sandwiched between two narrow strips of
Group 8E - Instrument Panel Systems for more infor- plastic film.
mation on the airbag indicator lamp. Like the clockspring in a timepiece, the clockspring
One electronic impact sensor is used in this airbag tape has travel limits and can be damaged by being
system. The impact sensor is an accelerometer that wound too tightly. To prevent this from occurring, the
senses the rate of vehicle deceleration, which pro- clockspring is centered when it is installed on the
vides verification of the direction and severity of an steering column. Centering the clockspring indexes
impact. The impact sensor is calibrated for the spe- the clockspring tape to other steering components so
cific vehicle, and is only serviced as a unit with the that it can operate within its designed travel limits.
ACM. A pre-programmed decision algorithm in the However, if the clockspring is removed for service or
ACM microprocessor determines when the decelera- if the steering column is disconnected from the steer-
tion rate as signaled by the impact sensor indicates ing gear allowing the clockspring tape to change posi-
an impact that is severe enough to require airbag tion relative to the other steering components, it
system protection. When the programmed conditions must be re-centered following completion of the ser-
are met, the ACM sends an electrical signal to deploy vice or it may be damaged. Refer to Clockspring
the airbags. Centering in the Adjustments section of this group
In addition to the electronic impact sensor, there is for the proper centering procedures.
an electromechanical sensor within the ACM called a Service replacement clocksprings are shipped pre-
safing sensor. The safing sensor is a normally open centered and with a locking pin installed. This lock-
series switch located in the airbag deployment circuit ing pin should not be removed until the clockspring
of the ACM. This sensor detects impact energy of a has been installed on the steering column. If the
lesser magnitude than the electronic impact sensor, locking pin is removed before the clockspring is
and must be closed in order for the airbags to deploy. installed on a steering column, the clockspring cen-
The ACM also contains an energy-storage capaci- tering procedure must be performed.
tor. This capacitor stores enough electrical energy to
deploy the airbags for up to one second following a
battery disconnect or failure during an impact. The
purpose of the capacitor is to provide airbag system
DIAGNOSIS AND TESTING NOTE: If the airbag indicator lamp fails to light, or
lights and stays on, there is an airbag system mal-
AIRBAG SYSTEM function. See the proper Diagnostic Procedures
A DRB scan tool is required for diagnosis of the manual to diagnose the problem.
airbag system. See the proper Diagnostic Procedures
manual for more information.
(1) Connect the DRB scan tool to the 16-way data SERVICE PROCEDURES
link wire harness connector. The connector is located
on the driver side lower edge of the instrument AIRBAG SYSTEM
panel, outboard of the steering column (Fig. 1).
NON-DEPLOYED
At no time should any source of electricity be per-
mitted near the inflator on the back of an airbag
module. When carrying a non-deployed airbag mod-
ule, the trim cover or airbag side of the module
should be pointed away from the body to minimize
injury in the event of an accidental deployment. If
the module is placed on a bench or any other surface,
the trim cover or airbag side of the module should be
face up to minimize movement in the event of an
accidental deployment.
In addition, the airbag system should be disarmed
whenever any steering wheel, steering column, or
instrument panel components require diagnosis or
service. Failure to observe this warning could result
in accidental airbag deployment and possible per-
sonal injury. Refer to Group 8E - Instrument
Panel Systems for additional service procedures on
the instrument panel components. Refer to Group
19 - Steering for additional service procedures on
the steering wheel and steering column components.
Fig. 1 16-Way Data Link Connector - Typical
DISPOSAL OF NON-DEPLOYED AIRBAG MODULES
(2) Turn the ignition switch to the On position. Exit All damaged or faulty and non-deployed driver side
the vehicle with the DRB. Be certain that the DRB con- or passenger side airbag modules which are replaced
tains the latest version of the proper DRB software. on vehicles are to be returned. If an airbag module
(3) Using the DRB, read and record the active assembly is faulty or damaged and non-deployed,
Diagnostic Trouble Code (DTC) data. refer to the parts return list in the current Chrysler
(4) Read and record any stored DTC data. Corporation Warranty Policies and Procedures man-
(5) See the proper Diagnostic Procedures manual if ual for the proper handling and disposal procedures.
any DTC is found in Step 3 or Step 4.
(6) After completing the necessary repairs, try to DEPLOYED
erase the stored DTC data. If any problems remain, Any vehicle which is to be returned to use after an
the stored DTC data will not erase. See the proper airbag deployment, must have both airbag modules,
Diagnostic Procedures manual for the procedures to the instrument panel assembly, the passenger side
diagnose any stored DTC that will not erase. airbag module door and the clockspring replaced.
(7) With the ignition switch still in the On posi- These components will be damaged or weakened as a
tion, check to be certain that nobody is in the vehicle. result of an airbag deployment, which may or may
(8) From outside of the vehicle (away from the air- not be obvious during a visual inspection, and are
bags in case of an accidental deployment) turn the not intended for reuse.
ignition switch to the Off position for about ten sec- Other vehicle components should be closely
onds, and then back to the On position. Observe the inspected, but are to be replaced only as required by
airbag indicator lamp in the instrument cluster. It the extent of the visible damage incurred.
should light for six to eight seconds, and then go out.
This indicates that the airbag system is functioning
normally.
STORAGE Begin the cleanup by removing the airbag modules
An airbag module must be stored in its original, from the vehicle. Refer to Driver Side Airbag Mod-
special container until used for service. Also, it must ule and Passenger Side Airbag Module in the
be stored in a clean, dry environment; away from Removal and Installation section of this group for the
sources of extreme heat, sparks, and high electrical procedures.
energy. Always place or store an airbag module on a Use a vacuum cleaner to remove any residual pow-
surface with its trim cover or airbag side facing up, der from the vehicle interior. Clean from outside the
to minimize movement in case of an accidental vehicle and work your way inside, so that you avoid
deployment. kneeling or sitting on a non-cleaned area.
Be sure to vacuum the heater and air conditioning
CLEANUP PROCEDURE outlets as well (Fig. 3). Run the heater and air con-
Following an airbag system deployment, the vehi- ditioner blower on the lowest speed setting and vac-
cle interior will contain a powdery residue. This res- uum any powder expelled from the outlets. You may
idue consists primarily of harmless particulate need to vacuum the interior of the vehicle a second
by-products of the small pyrotechnic charge used to time to recover all of the powder.
initiate the airbag deployment propellant. However,
this residue will also contain traces of sodium
hydroxide powder, a chemical by-product of the pro-
pellant material that is used to generate the nitrogen
gas that inflates the airbag. Since sodium hydroxide
powder can irritate the skin, eyes, nose, or throat, be
sure to wear safety glasses, rubber gloves, and a
long-sleeved shirt during cleanup (Fig. 2).
Fig. 3 Vacuum Heater and A/C Outlets - Typical

Place the deployed airbag modules in your vehicu-
lar scrap pile.

DRIVER SIDE AIRBAG MODULE
Fig. 2 Wear Safety Glasses and Rubber Gloves - The following procedure is for replacement of a
Typical faulty or damaged driver side airbag module. If the
WARNING: IF YOU EXPERIENCE SKIN IRRITATION driver side airbag has been deployed, the clockspring
DURING CLEANUP, RUN COOL WATER OVER THE must also be replaced. Refer to Clockspring in the
AFFECTED AREA. ALSO, IF YOU EXPERIENCE Removal and Installation section of this group for the
IRRITATION OF THE NOSE OR THROAT, EXIT THE additional service procedures for the clockspring.
VEHICLE FOR FRESH AIR UNTIL THE IRRITATION
CEASES. IF IRRITATION CONTINUES, SEE A PHYSI-
CIAN.
WARNING: (5) The clockspring airbag wire harness connector
• THE AIRBAG SYSTEM IS A SENSITIVE, COM- is a tight snap-fit into the airbag module connector
PLEX ELECTROMECHANICAL UNIT. BEFORE receptacle, which is located on the airbag inflator on
ATTEMPTING TO DIAGNOSE OR SERVICE ANY AIR- the back of the airbag module. Firmly grasp and pull
BAG SYSTEM OR RELATED STEERING WHEEL, or gently pry on the clockspring airbag wire harness
STEERING COLUMN, OR INSTRUMENT PANEL connector to disconnect it from the airbag module.
COMPONENTS YOU MUST FIRST DISCONNECT Do not pull on the clockspring wire harness to
AND ISOLATE THE BATTERY NEGATIVE (GROUND) disengage the connector from the airbag mod-
CABLE. THEN WAIT TWO MINUTES FOR THE SYS- ule connector receptacle.
TEM CAPACITOR TO DISCHARGE BEFORE FUR- (6) Remove the driver side airbag module from the
THER SYSTEM SERVICE. THIS IS THE ONLY SURE steering wheel.
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE (7) If the driver side airbag has been deployed, the
TO DO THIS COULD RESULT IN ACCIDENTAL AIR- clockspring must be replaced. Refer to Clockspring
BAG DEPLOYMENT AND POSSIBLE PERSONAL in the Removal and Installation section of this group
INJURY. for the clockspring service procedures.
• WHEN REMOVING A DEPLOYED AIRBAG MOD-
ULE, RUBBER GLOVES, EYE PROTECTION, AND A INSTALLATION
LONG-SLEEVED SHIRT SHOULD BE WORN. THERE
MAY BE DEPOSITS ON THE AIRBAG MODULE AND WARNING:
OTHER INTERIOR SURFACES. IN LARGE DOSES, • USE EXTREME CARE TO PREVENT ANY FOR-
THESE DEPOSITS MAY CAUSE IRRITATION TO THE EIGN MATERIAL FROM ENTERING THE DRIVER
SKIN AND EYES. SIDE AIRBAG MODULE, OR BECOMING
ENTRAPPED BETWEEN THE AIRBAG CUSHION
AND THE DRIVER SIDE AIRBAG TRIM COVER.
REMOVAL FAILURE TO OBSERVE THIS WARNING COULD
(1) Disconnect and isolate the battery negative RESULT IN OCCUPANT INJURIES UPON AIRBAG
cable. If either of the airbags has not been deployed, DEPLOYMENT.
wait two minutes for the system capacitor to dis- • THE DRIVER SIDE AIRBAG MODULE TRIM
charge before further service. COVER MUST NEVER BE PAINTED. REPLACEMENT
(2) From the underside of the steering wheel, TRIM COVERS ARE SERVICED IN THE ORIGINAL
remove the two screws that secure the driver side COLORS. PAINT MAY CHANGE THE WAY IN WHICH
airbag module to the steering wheel (Fig. 4). THE MATERIAL OF THE TRIM COVER RESPONDS
TO AN AIRBAG DEPLOYMENT. FAILURE TO
OBSERVE THIS WARNING COULD RESULT IN
OCCUPANT INJURIES UPON AIRBAG DEPLOY-
MENT.
(1) When installing the driver side airbag module,

reconnect the clockspring airbag wire harness con-
nector to the airbag module connector receptacle by
pressing straight in on the connector. You can be cer-
tain that the connector is fully engaged by listening
carefully for a distinct audible click as the connector
snaps into place.
(2) Reconnect the clockspring horn switch wire
harness connector to the horn switch feed wire con-
nector, which is located on the back of the airbag
module.
(3) Carefully position the driver side airbag mod-
Fig. 4 Driver Side Airbag Module Remove/Install ule in the steering wheel. Be certain that the clock-
(3) Pull the airbag module away from the steering spring wire harnesses in the steering wheel hub area
wheel far enough to access the two wire harness con- are not pinched between the airbag module and the
nectors on the back of the airbag module. steering wheel.
(4) Disconnect the clockspring horn switch wire (4) From the underside of the steering wheel,
harness connector from the horn switch feed wire install and tighten the two driver side airbag module
connector, which is located on the back of the airbag mounting screws. Tighten the screws to 10.2 N·m (90
module. in. lbs.).
(5) Do not reconnect the battery negative cable at
this time. Refer to Airbag System in the Diagnosis
and Testing section of this group for the proper pro-
cedures.
DRIVER SIDE AIRBAG MODULE TRIM COVER

The horn switch is integral to the driver side air-
bag module trim cover. If either component is faulty
or damaged, the entire driver side airbag module
trim cover and horn switch unit must be replaced.
WARNING:
• THE AIRBAG SYSTEM IS A SENSITIVE, COM-
PLEX ELECTROMECHANICAL UNIT. BEFORE
ATTEMPTING TO DIAGNOSE OR SERVICE ANY AIR-
BAG SYSTEM OR RELATED STEERING WHEEL,
STEERING COLUMN, OR INSTRUMENT PANEL Fig. 5 Horn Switch Feed Wire Remove/Install - w/o
COMPONENTS YOU MUST FIRST DISCONNECT Speed Control
AND ISOLATE THE BATTERY NEGATIVE (GROUND)
CABLE. THEN WAIT TWO MINUTES FOR THE SYS-
TEM CAPACITOR TO DISCHARGE BEFORE FUR-
THER SYSTEM SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO DO THIS COULD RESULT IN ACCIDENTAL AIR-
INJURY.
• THE HORN SWITCH IS INTEGRAL TO THE AIR-
BAG MODULE TRIM COVER. SERVICE OF THIS
COMPONENT SHOULD BE PERFORMED ONLY BY
CHRYSLER-TRAINED AND AUTHORIZED DEALER
SERVICE TECHNICIANS. FAILURE TO TAKE THE
PROPER PRECAUTIONS OR TO FOLLOW THE
PROPER PROCEDURES COULD RESULT IN ACCI-
DENTAL, INCOMPLETE, OR IMPROPER AIRBAG
DEPLOYMENT AND POSSIBLE OCCUPANT INJU-
Fig. 6 Horn Switch Feed Wire Remove/Install -
RIES.
w/Speed Control
(4) Remove the four nuts that secure the upper
REMOVAL and lower trim cover retainers to the studs on the
(1) Disconnect and isolate the battery negative back of the driver side airbag housing (Fig. 7) or (Fig.
cable. If either of the airbags has not been deployed, 8).
wait two minutes for the system capacitor to dis- (5) Remove the upper and lower trim cover retain-
charge before further service. ers from the airbag housing studs.
(2) Remove the driver side airbag module from the (6) Remove the horn switch ground wire eyelet
steering wheel. Refer to Driver Side Airbag Mod- from the upper airbag housing stud.
ule in the Removal and Installation section of this (7) Disengage the four trim cover locking blocks
group for the procedures. from the lip around the outside edge of the driver
(3) Remove the plastic horn switch feed wire side airbag housing and remove the housing from the
retainer(s) from the stud(s) on the back of the driver cover (Fig. 9) or (Fig. 10).
side airbag housing (Fig. 5) or (Fig. 6).
Fig. 7 Driver Side Airbag Trim Cover Retainers Fig. 9 Driver Side Airbag Trim Cover Remove/Install
Remove/Install - w/o Speed Control - w/o Speed Control
Fig. 8 Driver Side Airbag Trim Cover Retainers Fig. 10 Driver Side Airbag Trim Cover Remove/
Remove/Install - w/Speed Control Install - w/Speed Control
INSTALLATION (3) Install the horn switch ground wire eyelet over
the upper airbag housing stud.
WARNING: (4) Install the upper and lower airbag trim cover
• USE EXTREME CARE TO PREVENT ANY FOR- retainers over the airbag housing studs. Be certain
EIGN MATERIAL FROM ENTERING THE DRIVER that the tabs on each retainer are engaged in the
SIDE AIRBAG MODULE, OR BECOMING retainer slots of the upper and lower trim cover lock-
ENTRAPPED BETWEEN THE AIRBAG CUSHION ing blocks (Fig. 9) or (Fig. 10).
AND THE DRIVER SIDE AIRBAG TRIM COVER. (5) Install and tighten the trim cover retainer
FAILURE TO OBSERVE THIS WARNING COULD mounting nuts on the airbag housing studs. Tighten
RESULT IN OCCUPANT INJURIES UPON AIRBAG the nuts to 10 N·m (90 in. lbs.).
DEPLOYMENT. (6) Install the driver side airbag module onto the
• THE DRIVER SIDE AIRBAG MODULE TRIM steering wheel. Refer to Driver Side Airbag Mod-
COVER MUST NEVER BE PAINTED. REPLACEMENT ule in the Removal and Installation section of this
TRIM COVERS ARE SERVICED IN THE ORIGINAL group for the procedures.
COLORS. PAINT MAY CHANGE THE WAY IN WHICH
THE MATERIAL OF THE TRIM COVER RESPONDS PASSENGER SIDE AIRBAG MODULE
TO AN AIRBAG DEPLOYMENT. FAILURE TO The following procedure is for replacement of a
OBSERVE THIS WARNING COULD RESULT IN faulty or damaged passenger side airbag module. If
OCCUPANT INJURIES UPON AIRBAG DEPLOY- the passenger side airbag module has been deployed,
MENT. the instrument panel assembly must be replaced.
The instrument panel assembly includes the passen-
(1) Carefully position the driver side airbag mod- ger side airbag module and the passenger side airbag
ule in the trim cover. Be certain that the horn switch door. Refer to Instrument Panel Assembly in the
feed and ground wires are not pinched between the Removal and Installation section of Group 8E -
airbag housing and the trim cover locking blocks. Instrument Panel Systems for the instrument panel
(2) Engage the upper and lower trim cover locking assembly service procedures.
blocks with the lip of the driver side airbag housing,
then engage the locking blocks on each side of the WARNING:
trim cover with the lip of the housing. Be certain • THE AIRBAG SYSTEM IS A SENSITIVE, COM-
that each of the locking blocks is fully engaged on PLEX ELECTROMECHANICAL UNIT. BEFORE
the lip of the airbag housing (Fig. 11). ATTEMPTING TO DIAGNOSE OR SERVICE ANY AIR-
STEERING COLUMN, OR INSTRUMENT PANEL
COMPONENTS YOU MUST FIRST DISCONNECT
INJURY.
ULE, RUBBER GLOVES, EYE PROTECTION, AND A
MAY BE DEPOSITS ON THE AIRBAG MODULE AND
OTHER INTERIOR SURFACES. IN LARGE DOSES,
THESE DEPOSITS MAY CAUSE IRRITATION TO THE
SKIN AND EYES.
REMOVAL
cable. If either of the airbags has not been deployed,
Fig. 11 Driver Side Airbag Trim Cover Locking
wait two minutes for the system capacitor to dis-
Blocks Engaged
charge before further service.
(2) Remove the instrument panel assembly from PASSENGER SIDE AIRBAG DOOR
the passenger compartment of the vehicle. Refer to
Instrument Panel Assembly in the Removal and WARNING:
Installation section of Group 8E - Instrument Panel • THE AIRBAG SYSTEM IS A SENSITIVE, COM-
Systems for the procedures. PLEX ELECTROMECHANICAL UNIT. BEFORE
(3) Place the instrument panel on a suitable work ATTEMPTING TO DIAGNOSE OR SERVICE ANY AIR-
surface. Be certain to take the proper precautions to BAG SYSTEM OR RELATED STEERING WHEEL,
protect the instrument panel from any possible cos- STEERING COLUMN, OR INSTRUMENT PANEL
metic damage. COMPONENTS YOU MUST FIRST DISCONNECT
(4) Remove the three nuts that secure the passen- AND ISOLATE THE BATTERY NEGATIVE (GROUND)
ger side airbag module to the studs on the instru- CABLE. THEN WAIT TWO MINUTES FOR THE SYS-
ment panel armature (Fig. 12). TEM CAPACITOR TO DISCHARGE BEFORE FUR-
INJURY.
ULE, RUBBER GLOVES, EYE PROTECTION, AND A
MAY BE DEPOSITS ON THE AIRBAG MODULE AND
OTHER INTERIOR SURFACES. IN LARGE DOSES,
Fig. 12 Passenger Side Airbag Module Remove/
THESE DEPOSITS MAY CAUSE IRRITATION TO THE
Install
SKIN AND EYES.
(5) Remove the passenger side airbag module from
the instrument panel.
REMOVAL
INSTALLATION (1) Disconnect and isolate the battery negative
cable. If either of the airbags has not been deployed,
WARNING: USE EXTREME CARE TO PREVENT wait two minutes for the system capacitor to dis-
ANY FOREIGN MATERIAL FROM ENTERING THE charge before further service.
PASSENGER SIDE AIRBAG MODULE, OR BECOM- (2) Remove the passenger side airbag module from
ING ENTRAPPED BETWEEN THE AIRBAG CUSHION the instrument panel. Refer to Passenger Side Air-
AND THE PASSENGER SIDE AIRBAG DOOR. FAIL- bag Module in the Removal and Installation section
URE TO OBSERVE THIS WARNING COULD RESULT of this group for the procedures.
IN OCCUPANT INJURIES UPON AIRBAG DEPLOY- (3) Remove the five screws that secure the passen-
MENT. ger side airbag door upper flange to the top of the
instrument panel (Fig. 13).
(1) Carefully position the passenger side airbag
module in the instrument panel.
(2) Install and tighten the three nuts that secure the
passenger side airbag module upper and lower mount-
ing brackets to the studs on the instrument panel arma-
ture. Tighten the nuts to 12 N·m (105 in. lbs.).
(3) Install the instrument panel assembly into the
passenger compartment of the vehicle. Refer to
Instrument Panel Assembly in the Removal and
Systems for the procedures. When installing the
instrument panel, be certain to reconnect the passen-
ger side airbag module wire harness to the cross-
body wire harness, and that the connector is fully
engaged and latched.
and Testing section of this group for the proper pro- Fig. 13 Passenger Side Airbag Door Upper Screws
cedures. Remove/Install
(4) Remove the grab handle bezel from the instru- the passenger side airbag door bracket screws are
ment panel. Refer to Instrument Panel Grab Han- removed.
dle Bezel in the Removal and Installation section of (2) Position the passenger side airbag door to the
Group 8E - Instrument Panel Systems for the proce- instrument panel and align the mounting holes in
dures. each end of the airbag door bracket with the J-nuts
(5) Remove the five screws that secure the passen- on the instrument panel armature.
ger side airbag door lower flange to the instrument (3) Install and tighten the two screws that secure
panel above the glove box opening. the passenger side airbag door bracket to the instru-
(6) Remove the two screws that secure the ends of ment panel armature. Tighten the screws to 12 N·m
the passenger side airbag door bracket to the instru- (105 in. lbs.).
ment panel armature (Fig. 14). (4) Install and tighten the five screws that secure
the passenger side airbag door lower flange to the
instrument panel above the glove box opening.
Tighten the screws to 2.2 N·m (20 in. lbs.).
(5) Install the grab handle bezel onto the instru-
ment panel. Refer to Instrument Panel Grab Han-
dle Bezel in the Removal and Installation section of
Group 8E - Instrument Panel Systems for the proce-
dures.
(6) Install and tighten the five screws that secure
the passenger side airbag door upper flange to the
top of the instrument panel. Tighten the screws to
2.2 N·m (20 in. lbs.).
(7) Install the passenger side airbag module onto
Fig. 14 Passenger Side Airbag Door Remove/Install the instrument panel. Refer to Passenger Side Air-
bag Module in the Removal and Installation section
(7) Remove and discard the two passenger side air- of this group for the procedures.
bag door bracket J-nuts from the instrument panel
armature. These J-nuts must be replaced with new PASSENGER SIDE AIRBAG ON/OFF SWITCH
parts whenever the passenger side airbag door
bracket screws are removed. WARNING: THE AIRBAG SYSTEM IS A SENSITIVE,
(8) Remove the passenger side airbag door from COMPLEX ELECTROMECHANICAL UNIT. BEFORE
the instrument panel. ATTEMPTING TO DIAGNOSE OR SERVICE ANY AIR-
INSTALLATION STEERING COLUMN, OR INSTRUMENT PANEL
WARNING: AND ISOLATE THE BATTERY NEGATIVE (GROUND)
• USE EXTREME CARE TO PREVENT ANY FOR- CABLE. THEN WAIT TWO MINUTES FOR THE SYS-
EIGN MATERIAL FROM ENTERING THE PASSEN- TEM CAPACITOR TO DISCHARGE BEFORE FUR-
GER SIDE AIRBAG MODULE, OR BECOMING THER SYSTEM SERVICE. THIS IS THE ONLY SURE
ENTRAPPED BETWEEN THE AIRBAG CUSHION WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
AND THE PASSENGER SIDE AIRBAG DOOR. FAIL- TO DO THIS COULD RESULT IN ACCIDENTAL AIR-
URE TO OBSERVE THIS WARNING COULD RESULT BAG DEPLOYMENT AND POSSIBLE PERSONAL
IN OCCUPANT INJURIES UPON AIRBAG DEPLOY- INJURY.
MENT.
• THE PASSENGER SIDE AIRBAG DOOR MUST
NEVER BE PAINTED. REPLACEMENT AIRBAG REMOVAL
DOORS ARE SERVICED IN THE ORIGINAL COL-
ORS. PAINT MAY CHANGE THE WAY IN WHICH THE PASSENGER SIDE AIRBAG ON/OFF SWITCH
MATERIAL OF THE AIRBAG DOOR RESPONDS TO (1) Disconnect and isolate the battery negative
AN AIRBAG DEPLOYMENT. FAILURE TO OBSERVE cable. If either of the airbags has not been deployed,
THIS WARNING COULD RESULT IN OCCUPANT wait two minutes for the system capacitor to dis-
INJURIES UPON AIRBAG DEPLOYMENT. charge before further service.
(1) Install two new passenger airbag door bracket panel. Refer to Glove Box in the Removal and
J-nuts onto the instrument panel armature. These Installation section of Group 8E - Instrument Panel
J-nuts must be replaced with new parts whenever Systems for the procedures.
(3) Reach through the glove box opening to access
and disconnect the two passenger side airbag on/off
switch wire harness connectors from the instrument
panel wire harness. These connectors are retained on
a bracket located on the outboard glove box opening
reinforcement (Fig. 15).
Fig. 16 Passenger Side Airbag On/Off Switch

Remove/Install
(2) Remove the passenger side airbag on/off switch
from the bezel. Refer to Passenger Side Airbag
On/Off Switch in the Removal and Installation sec-
Fig. 15 Passenger Side Airbag On/Off Switch Wire (3) From the underside of the console, release the
Harness Connectors four latch tabs that secure the passenger side airbag
(4) Still reaching through the glove box opening, on/off switch bezel to the mounting hole in the front
disengage the passenger side airbag on/off switch of the full floor console or mini floor console.
wire harness from the retainer clip on the plenum (4) Remove the passenger side airbag on/off switch
bracket that supports the heater-A/C housing just bezel from the top of the full floor console or mini
inboard of the fuseblock module. floor console.
(5) Remove the full floor console or mini-floor con-
sole from the floor panel transmission tunnel. Refer INSTALLATION
to Full Floor Console or Mini Floor Console in
PASSENGER SIDE AIRBAG ON/OFF SWITCH
the Removal and Installation section of Group 23 -
Body for the procedures. (1) From the underside of the console, position the
(6) From the underside of the console, remove the passenger side airbag on/off switch to the back of the
three screws that secure the passenger side airbag switch bezel.
on/off switch to the back of the switch bezel (Fig. 16). (2) Install and tighten the three screws that secure
(7) Remove the passenger side airbag on/off switch the passenger side airbag on/off switch to the switch
from the switch bezel. bezel. Tighten the screws to 2.2 N·m (20 in. lbs.).
(3) Install the full floor console or mini floor con-
PASSENGER SIDE AIRBAG ON/OFF SWITCH BEZEL sole onto the floor panel transmission tunnel. Refer
The passenger side airbag on/off switch can be ser- to Full Floor Console or Mini Floor Console in
viced without removing the switch bezel from the the Removal and Installation section of Group 23 -
floor console. If the passenger side airbag on/off Body for the procedures.
switch bezel is removed from the floor console, it (4) Reach through the glove box opening to engage
must be replaced. The latch tabs that secure the the passenger side airbag on/off switch wire harness
bezel to the console will be damaged during the in the retainer clip on the plenum bracket that sup-
removal process. ports the heater-A/C housing just inboard of the fuse-
(1) Disconnect and isolate the battery negative block module.
cable. If either of the airbags has not been deployed, (5) Still reaching through the glove box opening,
wait two minutes for the system capacitor to dis- access and reconnect the two passenger side airbag
charge before further service. on/off switch wire harness connectors to the instru-
ment panel wire harness. These connectors are
retained on a bracket located on the outboard glove IMPROPER AIRBAG DEPLOYMENT AND POSSIBLE
box opening reinforcement. Be certain that both con- OCCUPANT INJURIES.
nectors are fully engaged and latched.
(6) Install the glove box onto the instrument panel.
Refer to Glove Box in the Removal and Installation REMOVAL
section of Group 8E - Instrument Panel Systems for (1) Disconnect and isolate the battery negative
the procedures. cable. If either of the airbags has not been deployed,
(7) Do not reconnect the battery negative cable at wait two minutes for the system capacitor to dis-
this time. Refer to Airbag System in the Diagnosis charge before further service.
and Testing section of this group for the proper pro- (2) Pull back the carpet from the floor panel trans-
cedures. mission tunnel area under the heater-A/C housing
floor duct and forward of the full floor console or
PASSENGER SIDE AIRBAG ON/OFF SWITCH BEZEL mini floor console.
(1) Position the passenger side airbag on/off switch (3) If the vehicle is equipped with the optional
bezel to the mounting hole at the front of the full Anti-lock Brake System (ABS), remove the accelera-
floor console or mini floor console. tion switch and mounting bracket from the floor
(2) Press down firmly and evenly on the passenger panel transmission tunnel (Fig. 17). Refer to Accel-
side airbag on/off switch bezel until each of the four eration Switch in the Removal and Installation sec-
latch tabs on the bezel is fully engaged with the tion of Group 5 - Brakes for the procedures.
mounting hole of the full floor console or mini floor
console.
(3) Install the passenger side airbag on/off switch
onto the bezel. Refer to Passenger Side Airbag
On/Off Switch in the Removal and Installation sec-
cedures.
AIRBAG CONTROL MODULE

WARNING:
• THE AIRBAG CONTROL MODULE CONTAINS
THE IMPACT SENSOR, WHICH ENABLES THE SYS-
TEM TO DEPLOY THE AIRBAG. BEFORE ATTEMPT- Fig. 17 Acceleration Switch Remove/Install
ING TO DIAGNOSE OR SERVICE ANY AIRBAG NOTE: Always remove and replace the airbag con-
SYSTEM OR RELATED STEERING WHEEL, STEER- trol module and its mounting bracket as a unit.
ING COLUMN, OR INSTRUMENT PANEL COMPO- Replacement modules include a replacement
NENTS YOU MUST FIRST DISCONNECT AND mounting bracket. Do not transfer the module to
ISOLATE THE BATTERY NEGATIVE (GROUND) another mounting bracket.
TEM CAPACITOR TO DISCHARGE BEFORE FUR- (4) Remove the four screws that secure the Airbag
THER SYSTEM SERVICE. THIS IS THE ONLY SURE Control Module (ACM) mounting bracket to the floor
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE panel transmission tunnel (Fig. 18).
TO DO THIS COULD RESULT IN ACCIDENTAL AIR- (5) Slide the ACM and mounting bracket out from
BAG DEPLOYMENT AND POSSIBLE PERSONAL under the heater-A/C housing floor duct far enough
INJURY. to access the ACM wire harness connector.
• NEVER STRIKE OR KICK THE AIRBAG CON- (6) Disconnect the cross-body wire harness connec-
TROL MODULE, AS IT CAN DAMAGE THE IMPACT tor from the ACM. To disconnect the cross-body wire
SENSOR OR AFFECT ITS CALIBRATION. IF AN AIR- harness connector from the ACM (Fig. 19):
BAG CONTROL MODULE IS ACCIDENTALLY (a) Pull the two white locks out about 3 millime-
DROPPED DURING SERVICE, THE MODULE MUST ters (0.125 in.) from each side of the connector.
BE SCRAPPED AND REPLACED WITH A NEW UNIT. (b) Squeeze the two connector latch tabs
FAILURE TO OBSERVE THIS WARNING COULD between the thumb and forefinger and pull the
RESULT IN ACCIDENTAL, INCOMPLETE, OR connector straight away from the ACM connector
receptacle.
INSTALLATION
(1) Reconnect the cross-body wire harness connec-
tor to the ACM connector receptacle. Be certain that
the connector latches are fully engaged and that the
white connector locks are pushed in.
(2) Carefully position the ACM and mounting
bracket unit to the floor panel transmission tunnel.
When the ACM is correctly positioned the arrow on
the ACM label will be pointed forward in the vehicle.
(3) Install and tighten the four screws that secure
the ACM mounting bracket to the floor panel trans-
mission tunnel. Tighten the screws to 10.7 N·m (95
in. lbs.).
(4) If the vehicle is equipped with the optional
ABS brakes, install the acceleration switch and
mounting bracket onto the floor panel transmission
tunnel. Refer to Acceleration Switch in the
Removal and Installation section of Group 5 - Brakes
for the procedures.
Fig. 18 Airbag Control Module Remove/Install cedures.
CLOCKSPRING
The clockspring cannot be repaired. It must be
replaced if faulty or damaged, or if the driver side
airbag has been deployed.
WARNING: THE AIRBAG SYSTEM IS A SENSITIVE,

COMPLEX ELECTROMECHANICAL UNIT. BEFORE
INJURY.
REMOVAL
NOTE: Before starting this procedure, be certain to
turn the steering wheel until the front wheels are in
the straight-ahead position.
(1) Place the front wheels in the straight-ahead

Fig. 19 Airbag Control Module Connector Removal position.
(7) Remove the ACM and mounting bracket from
the floor panel transmission tunnel as a unit.
(2) Remove the driver side airbag module from the (10) Remove both the upper and lower shrouds
steering wheel. Refer to Driver Side Airbag Mod- from the steering column.
ule in the Removal and Installation section of this (11) Disconnect the two instrument panel wire
group for the procedures. harness connectors from the lower clockspring con-
(3) If the vehicle is so equipped, disconnect the nector receptacles (Fig. 21).
upper clockspring wire harness connector from the
steering wheel wire harness for the vehicle speed
control switches located within the hub cavity of the
steering wheel.
(4) Remove the nut that secures the steering wheel
armature to the steering column upper shaft, which
is located within the hub cavity of the steering wheel.
(5) Pull the steering wheel off of the steering col-
umn upper shaft spline using a steering wheel puller
(Special Tool C-3428-B).
(6) Remove the steering column opening cover
from the instrument panel. Refer to Steering Col-
umn Opening Cover in the Removal and Installa-
tion section of Group 8E - Instrument Panel Systems
for the procedures.
(7) If the vehicle is so equipped, move the tilt
steering column to the fully raised position.
(8) Remove the three screws that secure the lower
Fig. 21 Clockspring Remove/Install
steering column shroud to the upper shroud (Fig. 20). (12) The multi-function switch water shield
bracket on the top of the steering column has a small
access window which allows access to the upper
clockspring latch with a small screwdriver (Fig. 22).
Gently pry both plastic latches of the clockspring
assembly to release them from the steering column
upper housing.
NOTE: If the clockspring plastic latches are broken,

be certain to remove the broken pieces from the
steering column upper housing.

Fig. 22 Upper Clockspring Latch Access Window
tilt steering column, loosen the two upper steering (13) Remove the clockspring from the steering col-
column mounting nuts. If the vehicle is equipped umn. The clockspring cannot be repaired. It must be
with the optional tilt steering column, move the tilt replaced if faulty or damaged, or if the driver side
steering column to the fully lowered position. airbag has been deployed.
(14) If the removed clockspring is to be reused, (7) Install the steering column opening cover onto
lock the clockspring rotor to the clockspring case to the instrument panel. Refer to Steering Column
maintain clockspring centering until it is reinstalled Opening Cover in the Removal and Installation sec-
on the steering column. This can be done by inserting tion of Group 8E - Instrument Panel Systems for the
a stiff wire through the small index hole located at procedures.
about the 11 o’clock position in the centered clock- (8) Install the steering wheel onto the steering col-
spring rotor and case. Refer to Clockspring Center- umn upper shaft. Be certain to index the flats on the
ing in the Adjustments section of this group for an hub of the steering wheel with the formations on the
illustration of the clockspring index hole. Bend the inside of the clockspring rotor. Pull the upper clock-
wire over after it has been inserted through the spring wire harnesses through the lower hole in the
index hole to prevent it from falling out. steering wheel armature.
(9) Install and tighten the steering wheel mount-
INSTALLATION ing nut. Tighten the nut to 61 N·m (45 ft. lbs.). Be
If the clockspring is not properly centered in rela- certain not to pinch the wire harnesses between the
tion to the steering wheel, steering shaft and steer- steering wheel and the nut.
ing gear, it may be damaged. Refer to Clockspring (10) If the vehicle is so equipped, reconnect the
Centering in the Adjustments section of this group upper clockspring wire harness connector to the
before installing or reinstalling a clockspring. steering wheel wire harness for the vehicle speed
Service replacement clocksprings are shipped pre- control switches.
centered and with a locking pin installed. This lock- (11) Install the driver side airbag module onto the
ing pin should not be removed until the clockspring steering wheel. Refer to Driver Side Airbag Mod-
has been installed on the steering column. If the ule in the Removal and Installation section of this
locking pin is removed before the clockspring is group for the procedures.
installed on a steering column, the clockspring cen-
tering procedure must be performed.
ADJUSTMENTS
NOTE: Before starting this procedure, be certain
that the front wheels are still in the straight-ahead CLOCKSPRING CENTERING
position. The clockspring is designed to wind and unwind
when the steering wheel is rotated, but is only
(1) If the removed clockspring is being reused, designed to rotate the same number of turns (about
remove the wire from the index hole that is locking five complete rotations) as the steering wheel can be
the clockspring rotor to the clockspring case to main- turned from stop to stop. Centering the clockspring
tain clockspring centering. indexes the clockspring tape to other steering compo-
(2) Be certain that the turn signal switch control nents so that it can operate within its designed
stalk is in the neutral position, then carefully slide travel limits. The rotor of a centered clockspring can
the centered clockspring down over the steering col- be rotated two and one-half turns in either direction
umn upper shaft until the clockspring latches engage from the centered position, without damaging the
the steering column upper housing. clockspring tape.
(3) If a new clockspring has been installed, remove However, if the clockspring is removed for service
the locking pin that is securing the clockspring rotor or if the steering column is disconnected from the
to the clockspring case and maintaining clockspring steering gear, the clockspring tape can change posi-
centering. tion relative to the other steering components. The
(4) Reconnect the two instrument panel wire har- clockspring must then be re-centered following com-
ness connectors to the lower clockspring connector pletion of the service or the clockspring tape may be
receptacles. Be certain that the connector latches are damaged.
fully engaged. Service replacement clocksprings are shipped pre-
(5) Position both the upper and lower shrouds onto centered and with a locking pin installed. This lock-
the steering column. ing pin should not be removed until the clockspring
(6) Install and tighten the three screws that secure has been installed on the steering column. If the
the lower steering column shroud to the upper locking pin is removed before the clockspring is
shroud. Tighten the screws to 2 N·m (18 in. lbs.). installed on a steering column, the clockspring cen-
tering procedure must be performed.
ADJUSTMENTS (Continued)
WARNING: THE AIRBAG SYSTEM IS A SENSITIVE,
COMPLEX ELECTROMECHANICAL UNIT. BEFORE
INJURY.
NOTE: Before starting this procedure, be certain to

turn the steering wheel until the front wheels are in
the straight-ahead position.
(1) Place the front wheels in the straight-ahead

position.
(2) Remove the clockspring from the steering col-
Fig. 23 Clockspring
umn. Refer to Clockspring in the Removal and
Installation section of this group for the procedures. (7) The front wheels should still be in the straight-
(3) Hold the clockspring case in one hand so that it ahead position. Install the clockspring onto the steer-
is oriented as it would be when it is installed on the ing column. Refer to Clockspring in the Removal
steering column (Fig. 23). and Installation section of this group for the proce-
(4) Use your other hand to rotate the clockspring dures.
rotor clockwise to the end of its travel. Do not apply
excessive torque.
(5) From the end of the clockwise travel, rotate the SPECIAL TOOLS
rotor about two and one-half turns counterclockwise,
until the rotor flats are horizontal. If the upper clock- PASSIVE RESTRAINT SYSTEMS
spring wire harnesses are not oriented towards the
bottom of the clockspring, rotate the rotor another
one-half turn in the counterclockwise direction.
(6) The clockspring is now centered. Lock the
clockspring rotor to the clockspring case to maintain
clockspring centering until it is reinstalled on the
steering column. This can be done by inserting a stiff
wire through the small index hole located at about
the 11 o’clock position in the centered clockspring
rotor and case. Bend the wire over after it has been
inserted through the index hole to prevent it from
falling out. Puller C-3428-B
TJ ELECTRICALLY HEATED SYSTEMS 8N - 1
ELECTRICALLY HEATED SYSTEMS

CONTENTS
page page
GENERAL INFORMATION DEFOGGER SWITCH . . . . . . . . . . . . . . . . . . . . . . 3

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1 DEFOGGER SYSTEM . . . . . . . . . . . . . . . . . . . . . 2
DESCRIPTION AND OPERATION INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . . . . 4
DEFOGGER RELAY . . . . . . . . . . . . . . . . . . . . . . . 2 REAR GLASS HEATING GRID . . . . . . . . . . . . . . 3
DEFOGGER SWITCH . . . . . . . . . . . . . . . . . . . . . . 2 SERVICE PROCEDURES
INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . . . . 2 REAR GLASS HEATING GRID REPAIR . . . . . . . . 5
REAR GLASS HEATING GRID . . . . . . . . . . . . . . 1 REMOVAL AND INSTALLATION
DIAGNOSIS AND TESTING DEFOGGER RELAY . . . . . . . . . . . . . . . . . . . . . . . 6
DEFOGGER RELAY . . . . . . . . . . . . . . . . . . . . . . . 3 DEFOGGER SWITCH . . . . . . . . . . . . . . . . . . . . . . 6
GENERAL INFORMATION Following are general descriptions of the major

components in the defogger system. Refer to 8W-48 -
INTRODUCTION Rear Window Defogger in Group 8W - Wiring Dia-
An electrically heated rear window defogger is grams for complete circuit descriptions and diagrams.
available as factory-installed equipment on models
equipped with the hardtop option. The defogger will DESCRIPTION AND OPERATION
only operate when the ignition switch is in the On
position. When the defogger switch is in the On posi-
REAR GLASS HEATING GRID
tion, an electric heater grid on the rear window glass
The heated rear window glass has two electrically
is energized. This grid produces heat to help clear
conductive vertical bus bars and a series of horizon-
the rear window glass of ice, snow, or fog.
tal grid lines made of a silver-ceramic material,
The defogger system is controlled by a switch
which is baked on and bonded to the inside surface of
located in the accessory switch bezel, which is near
the glass. The grid lines and bus bars comprise a
the bottom of the instrument panel center bezel and
parallel electrical circuit.
next to the ash receiver. An amber indicator lamp in
When the rear window defogger switch is placed in
the switch button will light to indicate when the
the On position, electrical current is directed to the
defogger system is turned on. The instrument cluster
rear window grid lines through the bus bars. The
circuitry, which contains the defogger system timer
grid lines heat the rear window to clear the surface
logic, monitors the state of the defogger switch
of fog or snow. Protection for the heated grid circuit
through a hard-wired input. The instrument cluster
is provided by a fuse in the Power Distribution Cen-
circuitry controls the defogger system through a
ter (PDC).
hard-wired control output to the defogger relay.
The grid lines and bus bars are highly resistant to
The defogger system will be automatically turned
abrasion. However, it is possible for an open circuit
off after a programmed time interval of about ten
to occur in an individual grid line, resulting in no
minutes. After the initial time interval has expired, if
current flow through the line.
the defogger switch is turned on again during the
The grid lines can be damaged or scraped off with
same ignition cycle, the defogger system will auto-
sharp instruments. Care should be taken when clean-
matically turn off after about five minutes.
ing the glass or removing foreign materials, decals,
The defogger system will automatically shut off if
or stickers from the glass. Normal glass cleaning sol-
the ignition switch is turned to the Off position, or it
vents or hot water used with rags or toweling is rec-
can be turned off manually by depressing the instru-
ommended.
ment panel switch. Refer to the owner’s manual for
A repair kit is available to repair the grid lines and
more information on the defogger system controls
bus bars, or to reinstall the heated glass pigtail
and operation.
wires.
8N - 2 ELECTRICALLY HEATED SYSTEMS TJ
DEFOGGER SWITCH DEFOGGER RELAY

The rear window defogger switch is installed in the The rear window defogger relay is a International
instrument panel accessory switch bezel, which is Standards Organization (ISO)-type relay. The rear
located near the bottom of the instrument panel cen- window defogger relay is a electromechanical device
ter bezel area, next to the ash receiver. The momen- that switches fused battery current to the rear glass
tary-type switch provides a hard-wired ground signal heating grid and the indicator lamp of the defogger
to the instrument cluster each time it is depressed. switch, when the instrument cluster rear window
The instrument cluster rear window defogger timer defogger timer and logic circuitry grounds the relay
and logic circuitry responds by energizing or de-ener- coil. See Defogger Relay in the Diagnosis and Testing
gizing the rear window defogger relay. section of this group for more information.
Energizing the rear window defogger relay pro- The rear window defogger relay is located in the
vides electrical current to the rear window defogger Power Distribution Center (PDC) in the engine com-
grid. An amber indicator lamp in the defogger switch, partment. Refer to the PDC label for relay identifica-
which lights to indicate when the defogger system is tion and location.
turned On, is also powered by the defogger relay out- The rear window defogger relay cannot be repaired
put. and, if faulty or damaged, it must be replaced.
The defogger switch illumination lamp and indica-
tor lamp bulbs are serviceable. The defogger switch
cannot be repaired and, if faulty or damaged, it must DIAGNOSIS AND TESTING
be replaced.
DEFOGGER SYSTEM
INSTRUMENT CLUSTER For circuit descriptions and diagrams, refer to
The instrument cluster is an electromechanical 8W-48 - Rear Window Defogger in Group 8W - Wir-
unit that contains integrated circuitry and internal ing Diagrams. The operation of the electrically
programming to perform a variety of functions. The heated rear window defogger system can be con-
instrument cluster circuitry monitors hard-wired firmed in one of the following manners:
switch inputs, as well as message inputs received 1. Turn the ignition switch to the On position.
from other vehicle electronic control modules on the While monitoring the instrument panel voltmeter, set
Chrysler Collision Detection (CCD) data bus network. the defogger switch in the On position. When the
The instrument cluster uses these many inputs defogger switch is turned On, a distinct voltmeter
along with its internal programming and integral needle deflection should be noted.
timer and logic circuitry to perform the functions of 2. Turn the ignition switch to the On position. Set
the rear window defogger timer on this model. The the defogger switch in the On position. The rear win-
instrument cluster circuitry also has a self-diagnostic dow defogger operation can be checked by feeling the
capability. Refer to Instrument Cluster in Group 8E - rear window glass. A distinct difference in tempera-
Instrument Panel Systems for more information on ture between the grid lines and the adjacent clear
this feature. glass can be detected within three to four minutes of
However, there are no diagnostics available for the operation.
rear window defogger timer and logic circuitry. 3. Using a 12-volt DC voltmeter, contact the rear
Therefore, the diagnosis for this system consists of glass heating grid terminal A (right side) with the
confirming the presence of a rear window defogger negative lead, and terminal B (left side) with the pos-
switch input signal at the instrument cluster connec- itive lead (Fig. 1). The voltmeter should read battery
tor, and the resulting rear window defogger relay voltage.
control output signal at the defogger relay. For diag- The above checks will confirm system operation.
nosis of the CCD data bus and the data bus message Illumination of the defogger switch indicator lamp
inputs, a DRB scan tool and the proper Diagnostic means that there is electrical current available at the
Procedures manual are recommended. output of the defogger relay, but does not confirm
Refer to Instrument Cluster in Group 8E - Instru- that the electrical current is reaching the rear glass
ment Panel Systems for the service procedures for heating grid lines.
the instrument cluster. The rear window defogger If the defogger system does not operate, the prob-
timer and logic circuitry cannot be adjusted or lem should be isolated in the following manner:
repaired and, if faulty or damaged, the instrument (1) Confirm that the ignition switch is in the On
cluster assembly must be replaced. position.
(2) Ensure that the rear glass heating grid feed
and ground wires are connected to the glass. Confirm
that the ground wire has continuity to ground.
midpoint C with the positive lead. A reading of
approximately six volts indicates a line is good. A
reading of zero volts indicates a break in the grid
line between midpoint C and the left side bus bar. A
reading of ten to fourteen volts indicates a break
between midpoint C and the right side bus bar. Move
the positive lead on the grid line towards the break
and the voltage reading will change as soon as the
break is crossed.
DEFOGGER SWITCH
8W-48 - Rear Window Defogger in Group 8W - Wir-
ing Diagrams.
Fig. 1 Rear Window Glass Grid Test WARNING: ON VEHICLES EQUIPPED WITH AIR-
(3) Check the fuses in the Power Distribution Cen- BAGS, REFER TO GROUP 8M - PASSIVE
ter (PDC) and in the fuseblock module. The fuses RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
must be tight in their receptacles and all electrical STEERING WHEEL, STEERING COLUMN, OR
connections must be secure. INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
When the above steps have been completed and the SERVICE. FAILURE TO TAKE THE PROPER PRE-
rear glass heating grid is still inoperative, one or CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
more of the following is faulty: BAG DEPLOYMENT AND POSSIBLE PERSONAL
• Defogger switch INJURY.
• Defogger relay
• Instrument cluster circuitry
cable. Remove the accessory switch bezel from the
• Rear window grid lines (all grid lines would
instrument panel and unplug the defogger switch
have to be broken or one of the feed wires discon-
wire harness connector.
nected for the entire system to be inoperative).
(2) Check for continuity between the ground cir-
If setting the defogger switch to the On position
cuit cavity of the defogger switch wire harness con-
produces a severe voltmeter deflection, check for a
nector and a good ground. There should be
short circuit between the defogger relay output and
continuity. If OK, go to Step 3. If not OK, repair the
the rear glass heating grid.
open circuit as required.
REAR GLASS HEATING GRID
cuit terminal and the rear window defogger switch
sense circuit terminal on the back of the defogger
8W-48 - Rear Window Defogger in Group 8W - Wir-
switch housing (Fig. 2). There should be momentary
ing Diagrams. To detect breaks in the grid lines, the
continuity as the defogger switch button is depressed,
following procedure is required:
and then no continuity. If OK, see the diagnosis for
(1) Turn the ignition switch to the On position. Set
the Instrument Cluster in this group. If not OK,
the defogger switch in the On position. The indicator
replace the faulty switch.
lamp should light. If OK, go to Step 2. If not OK, see
the Defogger Relay diagnosis in this group.
(2) Using a 12-volt DC voltmeter, contact the ver-
DEFOGGER RELAY
tical bus bar on the right side of the vehicle with the WARNING: ON VEHICLES EQUIPPED WITH AIR-
negative lead. With the positive lead, contact the ver- BAGS, REFER TO GROUP 8M - PASSIVE
tical bus bar on the left side of the vehicle. The volt- RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
meter should read battery voltage. If OK, go to Step STEERING WHEEL, STEERING COLUMN, OR
3. If not OK, repair the open circuit to the defogger INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
relay as required. SERVICE. FAILURE TO TAKE THE PROPER PRE-
(3) With the negative lead of the voltmeter, contact CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
a good body ground point. The voltage reading should BAG DEPLOYMENT AND POSSIBLE PERSONAL
not change. If OK, go to Step 4. If not OK, repair the INJURY.
circuit to ground as required.
(4) Connect the negative lead of the voltmeter to
the right side bus bar and touch each grid line at
Fig. 3 Defogger Relay

rear glass heating grid and defogger switch connec-
tors at all times. If OK, go to Step 4. If not OK,
repair the open circuit(s) as required.
(4) The coil battery terminal (86) is connected to
the electromagnet in the relay. This terminal is pro-
Fig. 2 Defogger Switch Continuity vided with ground by the instrument cluster rear
RELAY TEST window defogger timer and logic circuitry to energize
The defogger relay (Fig. 3) is located in the Power the defogger relay. There should be continuity to
Distribution Center (PDC), in the engine compart- ground at the cavity for relay terminal 86 when the
ment. Remove the defogger relay from the PDC to defogger switch is turned On. However, with the
perform the following tests: defogger relay removed, the defogger switch indicator
(1) A relay in the de-energized position should lamp will not light to show that the defogger system
have continuity between terminals 87A and 30, and is turned On. Be certain that you depress the defog-
no continuity between terminals 87 and 30. If OK, go ger switch at least twice to confirm that the system
to Step 2. If not OK, replace the faulty relay. is turned on during this test. If OK, go to Step 5. If
(2) Resistance between terminals 85 and 86 (elec- not OK, repair the open circuit to the instrument
tromagnet) should be 75 6 10 ohms. If OK, go to cluster as required.
Step 3. If not OK, replace the faulty relay. (5) The coil ground terminal (85) is connected to
(3) Connect a battery to terminals 85 and 86. the electromagnet in the relay. It is connected to
There should now be continuity between terminals fused ignition switch output voltage and should be
30 and 87, and no continuity between terminals 87A hot when the ignition switch is in the On position.
and 30. If OK, see the Relay Circuit Test in this Check for battery voltage at the cavity for relay ter-
group. If not OK, replace the faulty relay. minal 85 with the ignition switch in the On position.
If OK, see the diagnosis for Instrument Cluster in
RELAY CIRCUIT TEST this group. If not OK, repair the open circuit to the
(1) The relay common feed terminal cavity (30) is fuse in the fuseblock module as required.
connected to battery voltage and should be hot at all
times. If OK, go to Step 2. If not OK, repair the open INSTRUMENT CLUSTER
circuit to the PDC fuse as required. Before performing this test, complete the Defogger
(2) The relay normally closed terminal (87A) is Switch and the Defogger Relay tests as described in
connected to terminal 30 in the de-energized position, this group. For circuit descriptions and diagrams,
but is not used for this application. Go to Step 3. refer to 8W-48 - Rear Window Defogger in Group 8W
(3) The relay normally open terminal (87) is con- - Wiring Diagrams.
nected to the common feed terminal (30) in the ener-
gized position. This terminal supplies battery voltage
to the rear glass heating grid and the defogger
switch indicator lamp. There should be continuity
between the cavity for relay terminal 87 and the rear
window defogger relay output circuit cavities of the
WARNING: ON VEHICLES EQUIPPED WITH AIR- EYES. FOR SKIN CONTACT, WASH THE AFFECTED
BAGS, REFER TO GROUP 8M - PASSIVE AREAS WITH SOAP AND WATER. FOR CONTACT
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY WITH THE EYES, FLUSH WITH PLENTY OF WATER.
STEERING WHEEL, STEERING COLUMN, OR DO NOT TAKE INTERNALLY. IF TAKEN INTER-
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR NALLY, INDUCE VOMITING AND CALL A PHYSICIAN
SERVICE. FAILURE TO TAKE THE PROPER PRE- IMMEDIATELY. USE WITH ADEQUATE VENTILA-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- TION. DO NOT USE NEAR FIRE OR FLAME. CON-
BAG DEPLOYMENT AND POSSIBLE PERSONAL TAINS FLAMMABLE SOLVENTS. KEEP OUT OF THE
INJURY. REACH OF CHILDREN.
(1) Disconnect and isolate the battery negative (1) Mask the repair area so that the conductive
cable. Remove the defogger relay from the Power Dis- epoxy can be applied neatly. Extend the epoxy appli-
tribution Center (PDC) and unplug the defogger cation onto the grid line or the bus bar on each side
switch wire harness connector. of the break (Fig. 4).
ment panel. Refer to Instrument Cluster in Group 8E
- Instrument Panel Systems for the procedures.
(3) Check for continuity between the rear window
defogger switch sense circuit cavity of the right
instrument cluster wire harness connector (connector
B) and a good ground. There should be no continuity.
If OK, go to Step 4. If not OK, repair the short circuit
as required.
(4) Check for continuity between the rear window
defogger switch sense circuit cavities of the right
instrument cluster wire harness connector (connector
B) and the defogger switch wire harness connector.
There should be continuity. If OK, go to Step 5. If not
OK, repair the open circuit as required. Fig. 4 Grid Line Repair - Typical
(5) Check for continuity between the rear window (2) Follow the instructions in the repair kit for
defogger relay control circuit cavity of the right preparing the damaged area.
instrument cluster wire harness connector (connector (3) Remove the package separator clamp and mix
B) and a good ground. There should be no continuity. the two conductive epoxy components thoroughly
If OK, go to Step 6. If not OK, repair the short circuit within the packaging. Fold the package in half and
as required. cut the center corner to dispense the epoxy.
(6) Check for continuity between the rear window (4) For grid line repairs, mask the area to be
defogger relay control circuit cavities of the right repaired with masking tape or a template.
instrument cluster wire harness connector (connector (5) Apply the epoxy through the slit in the mask-
B) and the defogger relay receptacle (the cavity for ing tape or template. Overlap both ends of the break
ISO relay terminal 86) in the PDC. There should be by at least 19 millimeters (0.75 inch).
continuity. If OK, replace the faulty instrument clus- (6) For a terminal or pigtail wire replacement,
ter. If not OK, repair the open circuit as required. mask the adjacent areas so the epoxy can be
extended onto the adjacent grid line as well as the
bus bar. Apply a thin layer of epoxy to the area
SERVICE PROCEDURES where the terminal or pigtail wire was fastened and
onto the adjacent grid line.
REAR GLASS HEATING GRID REPAIR (7) Apply a thin layer of conductive epoxy to the
Repair of the rear glass heating grid lines, bus terminal or bare wire end of the pigtail and place it
bars, terminals or pigtail wires can be accomplished in the proper location on the bus bar. To prevent the
using a Mopar Rear Window Defogger Repair Kit terminal or pigtail wire from moving while the epoxy
(Part Number 4267922) or equivalent. is curing, it must be wedged or clamped.
(8) Carefully remove the masking tape or tem-
WARNING: MATERIALS CONTAINED IN THE plate.
REPAIR KIT MAY CAUSE SKIN OR EYE IRRITATION.
THE KIT CONTAINS EPOXY RESIN AND AMINE CAUTION: Do not allow the glass surface to exceed
TYPE HARDENER, WHICH ARE HARMFUL IF SWAL- 204° C (400° F) or the glass may fracture.
LOWED. AVOID CONTACT WITH THE SKIN AND
(9) Allow the epoxy to cure 24 hours at room tem- (4) Pull the accessory switch bezel out from the
perature, or use a heat gun with a 260° to 371° C instrument panel far enough to access the wire har-
(500° to 700° F) range for fifteen minutes. Hold the ness connectors.
heat gun approximately 25.4 centimeters (10 inches) (5) Unplug the wire harness connectors from the
from the repair. rear of the accessory switches and the cigar lighter/
(10) After the conductive epoxy is properly cured, power outlet.
remove the wedge or clamp from the terminal or pig- (6) Remove the accessory switch bezel from the
tail wire. Do not attach the wire harness connectors instrument panel.
until the curing process is complete. (7) With a small thin-bladed screwdriver, gently
(11) Check the operation of the rear window defog- pry the snap clips at the top and bottom of the rear
ger glass heating grid. window defogger switch receptacle on the back of the
accessory switch bezel and pull the switch out of the
bezel.
REMOVAL AND INSTALLATION (8) Reverse the removal procedures to install. Be
certain that both of the switch snap clip retainers in
DEFOGGER SWITCH the receptacle on the back of the accessory switch
bezel are fully engaged. Tighten the mounting screws
WARNING: ON VEHICLES EQUIPPED WITH AIR- to 2.2 N·m (20 in. lbs.).
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY DEFOGGER RELAY
cable.
(2) Remove the cover from the Power Distribution
Center (PDC) (Fig. 6).
INJURY.

cable.
panel. See Instrument Panel Center Bezel in Group
(3) Remove the four screws that secure the acces-
sory switch bezel to the instrument panel (Fig. 5).
Fig. 6 Power Distribution Center

(3) Refer to the label on the PDC for defogger
relay identification and location.
(4) Unplug the defogger relay from the PDC.
(5) Install the defogger relay by aligning the relay
terminals with the cavities in the PDC and pushing
the relay firmly into place.
(6) Install the PDC cover.
(7) Connect the battery negative cable.
Fig. 5 Accessory Switch Bezel Remove/Install (8) Test the relay operation.
TJ POWER DISTRIBUTION SYSTEMS 8O - 1
POWER DISTRIBUTION SYSTEMS

CONTENTS
page page
DESCRIPTION AND OPERATION REMOVAL AND INSTALLATION

FUSEBLOCK MODULE . . . . . . . . . . . . . . . . . . . . 2 FUSEBLOCK MODULE . . . . . . . . . . . . . . . . . . . . 4
POWER DISTRIBUTION CENTER . . . . . . . . . . . . 1 POWER DISTRIBUTION CENTER . . . . . . . . . . . . 2
POWER DISTRIBUTION SYSTEM . . . . . . . . . . . . 1
DESCRIPTION AND OPERATION molded plastic PDC housing is located on the right
side of the engine compartment, just forward of the
POWER DISTRIBUTION SYSTEM battery. The PDC housing has a molded plastic cover
that includes two integral pivot hooks on the out-
DESCRIPTION board side, and an integral latch on the inboard side.
This group covers the various standard and The PDC cover is easily removed for service access
optional power distribution components used on this and has a convenient adhesive-backed fuse and relay
model. Refer to Group 8W - Wiring Diagrams for layout label affixed to the inside surface of the cover
complete circuit diagrams of the various power distri- to ensure proper component identification.
bution components.
The power distribution system for this vehicle is
designed to provide safe, reliable, and centralized dis-
tribution of the electrical current required to operate
all of the many standard and optional factory-in-
stalled electrical and electronic powertrain, chassis,
safety, comfort and convenience systems. At the same
time, these systems were designed to provide conve-
nient to access centralized locations for conducting
diagnosis of faulty circuits, and for sourcing the addi-
tional current requirements of many aftermarket
vehicle accessory and convenience items.
These power distribution systems also incorporate
various types of circuit control and protection fea-
tures, including:
• Fuses
• Maxi fuse-type fusible links Fig. 1 Power Distribution Center
• Relays.
The PDC housing is secured to a stamped sheet
The power distribution system for this vehicle con-
metal bracket in the engine compartment by mount-
sists of the following components:
ing slots and tabs that are integral to the PDC hous-
• Power Distribution Center (PDC)
ing. The PDC mounting bracket is secured with three
• Fuseblock Module
screws to the right front inner fender shield above
Following are general descriptions of the major
the right front wheel house. A separate cover that is
components in the power distribution system. See the
secured by an integral bail strap to the rear of the
owner’s manual in the vehicle glove box for more
PDC housing is unlatched and removed to access the
information on the features, use and operation of all
battery/generator cable connection stud. The PDC is
of the power distribution system components.
integral to the dash wire harness, which exits from
the rearward end of the PDC housing.
POWER DISTRIBUTION CENTER The PDC houses up to fourteen blade-type maxi
fuses, which replace all in-line fusible links. The PDC
DESCRIPTION also houses up to six blade-type mini fuses, the ABS
All of the electrical current distributed throughout relay, and up to nine International Standards Orga-
this vehicle is directed through the standard equip- nization (ISO) relays (three standard-type and six
ment Power Distribution Center (PDC) (Fig. 1). The
8O - 2 POWER DISTRIBUTION SYSTEMS TJ
micro-type). Internal connection of all of the PDC cir- The fuses used in the fuseblock module are avail-
cuits is accomplished by an intricate combination of able for service replacement. The fuseblock module is
hard wiring and bus bars. Refer to Power Distribu- integral to the cross body wire harness. If any inter-
tion in the Contents of Group 8W - Wiring Diagrams nal circuit or if the fuseblock module housing is
for complete circuit diagrams. faulty or damaged, the entire fuseblock module and
The maxi fuses, mini fuses and relays are available cross body harness unit must be replaced.
for service replacement. The PDC unit cannot be
repaired and is only serviced as a unit with the dash
wire harness. If the PDC internal circuits or housing REMOVAL AND INSTALLATION
are faulty or damaged, the PDC and dash wire har-
ness unit must be replaced. POWER DISTRIBUTION CENTER
The Power Distribution Center (PDC) is serviced
FUSEBLOCK MODULE as a unit with the dash wire harness. If any internal
circuit of the PDC or if the PDC housing is faulty or
DESCRIPTION damaged, the entire PDC and the dash wire harness
An electrical module is mounted on the dash panel unit must be replaced.
in the passenger compartment of the vehicle. The
molded plastic fuseblock module housing has an inte- REMOVAL
gral mounting bracket that is secured with two (1) Disconnect and isolate the battery negative
screws to a bracket welded on the dash panel just cable.
above the heater and air conditioner housing. The (2) Disconnect each of the dash wire harness con-
glove box is rolled down from the instrument panel nectors. Refer to Connector Locations in the Con-
for service access of the fuseblock module fuses (Fig. tents of Group 8W - Wiring Diagrams for more
2). An adhesive-backed fuse layout label is located on information on the locations of the affected connec-
the heater and air conditioner housing below the tors.
fuseblock module to ensure proper fuse identification. (3) Remove all of the fasteners that secure each of
the dash wire harness ground eyelets to the vehicle
body and chassis components. Refer to Connector
Locations in the Contents of Group 8W - Wiring
Diagrams for more information on the ground eyelet
locations.
(4) Disengage each of the retainers that secure the
dash wire harness to the vehicle body and chassis
components. Refer to Connector Locations in the
Contents of Group 8W - Wiring Diagrams for more
information on the retainer locations.
(5) Unlatch and remove the terminal stud cover
from the rearward end of the PDC (Fig. 3).
(6) Remove the nut that secures the eyelets of the
battery positive cable take out and the engine wire
harness take out to the stud on the PDC.
(7) Remove the battery positive cable take out and
the engine wire harness take out eyelets from the
PDC stud.
(8) Disengage the latches on the PDC mounting
bracket from the tabs on the PDC housing, and pull
Fig. 2 Fuseblock Module
the PDC housing upward to disengage the mounting
The fuseblock module serves to distribute electrical slots from the stanchions of the mounting bracket
current to many of the accessory systems in the vehi- (Fig. 4).
cle. All of the current entering and leaving the fuse- (9) Remove the PDC and the dash wire harness
block module does so through the cross body wire from the engine compartment as a unit.
harness. The fuseblock module houses up to twenty (10) Remove the three screws that secure the PDC
blade-type mini fuses. Internal connection of all of mounting bracket to the right front inner fender (Fig.
the fuseblock module circuits is accomplished by an 5).
intricate combination of hard wiring and bus bars. (11) Remove the PDC mounting bracket from the
Refer to Fuse/Fuse Block in the Contents of Group right front inner fender.
8W - Wiring Diagrams for complete circuit diagrams.
TJ POWER DISTRIBUTION SYSTEMS 8O - 3
Fig. 5 PDC Mounting Bracket Remove/Install

(2) Install and tighten the three screws that secure
the PDC mounting bracket to the right front inner
Fig. 3 Power Distribution Center Connections fender. Tighten the screws to 3.9 N·m (35 in. lbs.).
(3) Position the PDC and the dash wire harness
unit in the engine compartment.
(4) Engage the mounting slots on the PDC housing
with the stanchions of the PDC mounting bracket
and push the unit downward until the mounting
bracket latches engage the mounting tabs on the
PDC housing.
(5) Install the eyelets of the battery positive cable
take out and the engine wire harness take out onto
the PDC stud.
eyelet of the battery positive cable take out and the
engine wire harness take out onto the PDC stud.
Tighten the nut to 8.4 N·m (75 in. lbs.).
(7) Engage the tabs on the lower edge of the ter-
minal stud cover in the slots on the back of the PDC
housing, then engage the latch on the top of the
cover with the latch tabs on the PDC housing.
(8) Engage each of the retainers that secure the
Fig. 4 Power Distribution Center Remove/Install dash wire harness to the vehicle body and chassis
components. Refer to Connector Locations in the
INSTALLATION Contents of Group 8W - Wiring Diagrams for more
information on the retainer locations.
NOTE: If the PDC is being replaced with a new unit,
(9) Install all of the fasteners that secure each of
be certain to transfer each of the fuses and relays
the dash wire harness ground eyelets to the vehicle
from the old PDC to the proper cavities of the new
body and chassis components. Refer to Connector
PDC. Refer to Power Distribution in the Contents of
Locations in the Contents of Group 8W - Wiring
Group 8W - Wiring Diagrams for the proper PDC
Diagrams for more information on the ground eyelet
cavity assignments.
locations.
(1) Position the PDC mounting bracket onto the (10) Reconnect each of the dash wire harness con-
right front inner fender. nectors. Refer to Connector Locations in the Con-
tents of Group 8W - Wiring Diagrams for more
8O - 4 POWER DISTRIBUTION SYSTEMS TJ
information on the locations of the affected connec-
tors.
FUSEBLOCK MODULE
The fuseblock module is serviced as a unit with the
cross body wire harness. If any internal circuit of the
fuseblock module if the fuseblock module housing is
faulty or damaged, the entire fuseblock module and
the cross body wire harness unit must be replaced.

SERVICE. FAILURE TO TAKE THE PROPER PRE- Fig. 6 Fuseblock Module Remove/Install
BAG DEPLOYMENT AND POSSIBLE PERSONAL INSTALLATION
INJURY.
NOTE: If the fuseblock module is being replaced
with a new unit, be certain to transfer each of the
REMOVAL fuses from the old fuseblock module to the proper
(1) Disconnect and isolate the battery negative cavities of the new fuseblock module. Refer to
cable. Fuse/Fuse Block in the Contents of Group 8W - Wir-
(2) Remove the instrument panel assembly from ing Diagrams for the proper fuseblock module cav-
the dash panel. Refer to Instrument Panel Assem- ity assignments.
bly in the Removal and Installation section of Group
(1) Position the fuseblock module and the cross
body wire harness onto the dash panel as a unit.
(3) Disconnect each of the cross body wire harness
connectors. Refer to Connector Locations in the
the fuseblock module to the bracket on the dash
panel. Tighten the screws to 3.3 N·m (30 in. lbs.).
(3) Engage each of the retainers that secure the
tors.
cross body wire harness to the vehicle body and chas-
(4) Remove all of the fasteners that secure each of
sis components. Refer to Connector Locations in
the cross body wire harness ground eyelets to the
the Contents of Group 8W - Wiring Diagrams for
vehicle body and chassis components. Refer to Con-
more information on the retainer locations.
nector Locations in the Contents of Group 8W -
(4) Install all of the fasteners that secure each of
Wiring Diagrams for more information on the ground
the cross body wire harness ground eyelets to the
eyelet locations.
vehicle body and chassis components. Refer to Con-
(5) Disengage each of the retainers that secure the
nector Locations in the Contents of Group 8W -
cross body wire harness to the vehicle body and chas-
Wiring Diagrams for more information on the ground
sis components. Refer to Connector Locations in
eyelet locations.
the Contents of Group 8W - Wiring Diagrams for
(5) Reconnect each of the cross body wire harness
more information on the retainer locations.
connectors. Refer to Connector Locations in the
(6) Remove the two screws that secure the fuse-
block module to the bracket on the dash panel (Fig.
6).
tors.
(7) Remove the fuseblock module and the cross
(6) Install the instrument panel assembly onto the
body wire harness from the dash panel as a unit.
dash panel. Refer to Instrument Panel Assembly
in the Removal and Installation section of Group 8E -
Instrument Panel Systems for the procedures.
TJ VEHICLE THEFT/SECURITY SYSTEMS 8Q - 1
VEHICLE THEFT/SECURITY SYSTEMS

CONTENTS
page page

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1 SENTRY KEY IMMOBILIZER SYSTEM . . . . . . . . 3
SENTRY KEY IMMOBILIZER SYSTEM . . . . . . . . 1 SERVICE PROCEDURES
DESCRIPTION AND OPERATION SENTRY KEY IMMOBILIZER SYSTEM
SENTRY KEY IMMOBILIZER MODULE . . . . . . . . 1 TRANSPONDER PROGRAMMING . . . . . . . . . . 4
SENTRY KEY IMMOBILIZER SYSTEM REMOVAL AND INSTALLATION
INDICATOR LAMP . . . . . . . . . . . . . . . . . . . . . . 3 SENTRY KEY IMMOBILIZER MODULE . . . . . . . . 4
SENTRY KEY IMMOBILIZER TRANSPONDER . . 2
GENERAL INFORMATION and any stored DTC can be retrieved using a DRB
scan tool as described in the proper Diagnostic Pro-
INTRODUCTION cedures manual.
The Sentry Key Immobilizer System (SKIS) is
available factory-installed optional equipment for this DESCRIPTION AND OPERATION
model. Following are some general descriptions of the
features and components of the SKIS. Refer to the
SENTRY KEY IMMOBILIZER MODULE
vehicle owner’s manual for more information on the
The Sentry Key Immobilizer Module (SKIM) con-
use and operation of the SKIS. Refer to 8W-30 - Fuel/
tains a Radio Frequency (RF) transceiver and a cen-
Ignition System in Group 8W - Wiring Diagrams for
tral processing unit, which includes the Sentry Key
complete circuit descriptions and diagrams.
Immobilizer System (SKIS) program logic. The SKIS
programming enables the SKIM to program and
SENTRY KEY IMMOBILIZER SYSTEM retain in memory the codes of at least two, but no
The Sentry Key Immobilizer System (SKIS) is
more than eight electronically coded Sentry Key
designed to provide passive protection against unau-
transponders. The SKIS programming also enables
thorized vehicle use by preventing the engine from
the SKIM to communicate over the Chrysler Collision
operating while the system is armed. The primary
Detection (CCD) data bus network with the Power-
components of this system are the Sentry Key Immo-
train Control Module (PCM), the instrument cluster
bilizer Module (SKIM), the Sentry Key transponder,
and/or the DRB scan tool.
the SKIS indicator lamp, and the Powertrain Control
The SKIM transmits and receives RF signals
Module (PCM).
through a tuned antenna enclosed within a molded
The SKIM is installed on the steering column near
plastic ring formation that is integral to the SKIM
the ignition lock cylinder. The transponder is located
housing. When the SKIM is properly installed on the
under the molded rubber cap on the head of the igni-
steering column, the antenna ring is oriented around
tion key. The SKIS indicator lamp is located in the
the circumference of the ignition lock cylinder hous-
instrument cluster.
ing. This antenna ring must be located within eight
The SKIS includes two valid Sentry Key transpon-
millimeters (0.31 inches) of the Sentry Key in order
ders from the factory. If the customer wishes, addi-
to ensure proper RF communication between the
tional non-coded blank Sentry Keys are available.
SKIM and the Sentry Key transponder.
These blank keys can be cut to match a valid ignition
For added system security, each SKIM is pro-
key, but the engine will not start unless the key tran-
grammed with a unique “Secret Key” code and a
sponder is also programmed to the vehicle. The SKIS
security code. The SKIM keeps the “Secret Key” code
will recognize no more than eight valid Sentry Key
in memory and sends the code over the CCD data
transponders at any one time.
bus to the PCM, which also keeps this code in its
The SKIS performs a self-test each time the igni-
memory. The SKIM also sends the “Secret Key” code
tion switch is turned to the On position, and will
to each of the programmed Sentry Key transponders.
store Diagnostic Trouble Codes (DTCs) if a system
The security code is used by the assembly plant to
malfunction is detected. The SKIS can be diagnosed,
access the SKIS for initialization, or by the dealer
8Q - 2 VEHICLE THEFT/SECURITY SYSTEMS TJ
technician to access the system for service. The Procedures manual are required. The SKIM cannot
SKIM also stores in its memory the Vehicle Identifi- be repaired and, if faulty or damaged, the unit must
cation Number (VIN), which it learns through a CCD be replaced.
data bus message from the PCM during initializa-
tion. SENTRY KEY IMMOBILIZER TRANSPONDER
The SKIM and the PCM both use software that The Sentry Key Immobilizer System (SKIS) uses a
includes a rolling code algorithm strategy, which transponder that is integral to each of the two igni-
helps to reduce the possibility of unauthorized SKIS tion keys that are supplied with the vehicle when it
disarming. The rolling code algorithm ensures secu- is shipped from the factory. The transponder chip is
rity by preventing an override of the SKIS through insulated within a nylon mount inserted in the head
the unauthorized substitution of the SKIM or the of the key, and invisible beneath a molded rubber cap
PCM. However, the use of this strategy also means (Fig. 1).
that replacement of either the SKIM or the PCM
units will require a system initialization procedure to
restore system operation.
When the ignition switch is turned to the On or
Start positions, the SKIM transmits an RF signal to
excite the Sentry Key transponder. The SKIM then
listens for a return RF signal from the transponder
of the Sentry Key that is inserted in the ignition lock
cylinder. If the SKIM receives an RF signal with
valid “Secret Key” and transponder identification
codes, the SKIM sends a “valid key” message to the
PCM over the CCD data bus. If the SKIM receives
an invalid RF signal or no response, it sends “invalid
key” messages to the PCM. The PCM will enable or
disable engine operation based upon the status of the
SKIM messages.
The SKIM also sends messages to the instrument
cluster over the CCD data bus network to control the
SKIS indicator lamp. The SKIM sends messages to
the instrument cluster to turn the lamp on for about
Fig. 1 Sentry Key Immobilizer Transponder
three seconds when the ignition switch is turned to
the On position as a bulb test. After completion of Each Sentry Key transponder has a unique tran-
the bulb test, the SKIM sends bus messages to keep sponder identification code programmed into it by the
the lamp off for a duration of about one second. Then manufacturer. The Sentry Key Immobilizer Module
the SKIM sends messages to turn the lamp on or off (SKIM) has a unique “Secret Key” code programmed
based upon the results of the SKIS self-tests. If the into it by the manufacturer. When a Sentry Key
SKIS indicator lamp comes on and stays on after the transponder is programmed into the memory of the
bulb test, it indicates that the SKIM has detected a SKIM, the SKIM learns the transponder identifica-
system malfunction and/or that the SKIS has become tion code from the transponder, and the transponder
inoperative. learns the “Secret Key” code from the SKIM. Each of
If the SKIM detects an invalid key when the igni- these codes is stored within the transponder and in
tion switch is turned to the On position, it sends the nonvolatile memory of the SKIM. Therefore,
messages to the instrument cluster to flash the SKIS blank keys for the SKIS must be programmed by and
indicator lamp. The SKIM can also send messages to into the SKIM, in addition to being cut to match the
the instrument cluster to flash the lamp and to gen- mechanical coding of the ignition lock cylinder. See
erate a single audible chime tone. These functions Sentry Key Immobilizer System Transponder Pro-
serve as an indication to the customer that the SKIS gramming in this group for more information.
has been placed in its “Customer Learn” program- The Sentry Key transponder is within the range of
ming mode. See Sentry Key Immobilizer System the SKIM transceiver antenna ring when it is
Transponder Programming in this group for more inserted in the ignition lock cylinder. When the igni-
information on the “Customer Learn” programming tion switch is turned to the Start or On positions, the
mode. SKIM transceiver issues a Radio Frequency (RF) sig-
For diagnosis or initialization of the SKIM and the nal that excites the transponder chip. The transpon-
PCM, a DRB scan tool and the proper Diagnostic der chip responds by issuing an RF signal containing
its transponder identification code and the “Secret
Key” code. The SKIM transceiver compares the tran- DIAGNOSIS AND TESTING
sponder codes with the codes stored in its memory to
determine whether a valid key is in the ignition lock SENTRY KEY IMMOBILIZER SYSTEM
cylinder.
The Sentry Key transponder cannot be repaired WARNING: ON VEHICLES EQUIPPED WITH AIR-
and, if faulty or damaged, it must be replaced. BAGS, REFER TO GROUP 8M - PASSIVE
SENTRY KEY IMMOBILIZER SYSTEM STEERING WHEEL, STEERING COLUMN, OR
INDICATOR LAMP INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
The Sentry Key Immobilizer System (SKIS) indica- SERVICE. FAILURE TO TAKE THE PROPER PRE-
tor lamp gives an indication when the SKIS is faulty CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
or when the vehicle has been immobilized due to the BAG DEPLOYMENT AND POSSIBLE PERSONAL
use of an invalid ignition key. The lamp is controlled INJURY.
by the instrument cluster circuitry based upon mes-
sages received from the Sentry Key Immobilizer
NOTE: The following tests may not prove conclu-
Module (SKIM) on the Chrysler Collision Detection
sive in the diagnosis of this system. The most reli-
(CCD) data bus.
able, efficient, and accurate means to diagnose the
The SKIM sends messages to the instrument clus-
Sentry Key Immobilizer System involves the use of
ter to turn the lamp on for about three seconds when
a DRB scan tool. Refer to the proper Diagnostic
the ignition switch is turned to the On position as a
Procedures manual for the procedures.
bulb test. After completion of the bulb test, the SKIM
sends bus messages to keep the lamp off for a dura- The Sentry Key Immobilizer System (SKIS) and
tion of about one second. Then the SKIM sends mes- the Chrysler Collision Detection (CCD) data bus net-
sages to the instrument cluster circuitry to turn the work should be diagnosed using a DRB scan tool.
lamp on or off based upon the results of the SKIS The DRB will allow confirmation that the CCD data
self-tests. If the SKIS indicator lamp comes on and bus is functional, that the Sentry Key Immobilizer
stays on after the bulb test, it indicates that the Module (SKIM) is placing the proper messages on the
SKIM has detected a system malfunction and/or that CCD data bus, and that the Powertrain Control Mod-
the SKIS has become inoperative. ule (PCM) and the instrument cluster are receiving
If the SKIM detects an invalid key when the igni- the CCD data bus messages. Refer to the proper
tion switch is turned to the On position, it sends Diagnostic Procedures manual for the procedures.
messages to the instrument cluster to flash the SKIS Refer to 8W-39 - Vehicle Theft Security System in
indicator lamp. The SKIM can also send messages to Group 8W - Wiring Diagrams for complete circuit
the instrument cluster to flash the lamp and to gen- descriptions and diagrams.
erate a single audible chime tone. These functions (1) Check the fuses in the fuseblock module. If OK,
serve as an indication to the customer that the SKIS go to Step 2. If not OK, repair the shorted circuit or
has been placed in its “Customer Learn” program- component as required and replace the faulty fuse.
ming mode. See Sentry Key Immobilizer System (2) Disconnect and isolate the battery negative cable.
Transponder Programming in this group for more Unplug the wire harness connector at the SKIM. Check
information on the “Customer Learn” programming for continuity between the ground circuit cavity of the
mode. SKIM wire harness connector and a good ground. There
The SKIS indicator lamp uses a replaceable incan- should be continuity. If OK, go to Step 3. If not OK,
descent bulb and bulb holder on the instrument clus- repair the open circuit to ground as required.
ter electronic circuit board. Refer to Group 8E - (3) Connect the battery negative cable. Check for
Instrument Panel Systems for diagnosis and service battery voltage at the fused B(+) circuit cavity of the
of a faulty SKIS indicator lamp. If the SKIS indicator SKIM wire harness connector. If OK, go to Step 4. If
lamp comes on and stays on after the bulb test func- not OK, repair the open circuit to the fuse in the
tion, diagnosis of the SKIS should be performed with fuseblock module as required.
a DRB scan tool and the proper Diagnostic Proce- (4) Turn the ignition switch to the On position.
dures manual. Check for battery voltage at the fused ignition switch
output (run/start) circuit cavity of the SKIM wire
harness connector. If OK, use a DRB scan tool and
the proper Diagnostic Procedures manual to complete
the diagnosis of the SKIS. If not OK, repair the open
circuit to the fuse in the fuseblock module as
required.
8Q - 4 VEHICLE THEFT/SECURITY SYSTEMS TJ
SERVICE PROCEDURES If any of the above steps is not completed in the

proper sequence, or within the allotted time, the
SENTRY KEY IMMOBILIZER SYSTEM SKIS will automatically exit the “Customer Learn”
programming mode. The SKIS will also automatically
TRANSPONDER PROGRAMMING exit the “Customer Learn” programming mode if it
Two programmed Sentry Key transponders are sees a non-blank Sentry Key transponder when it
included with the Sentry Key Immobilizer System should see a blank, if it has already programmed
(SKIS) when it is shipped from the factory. The Sen- eight valid Sentry Keys, or if the ignition switch is
try Key Immobilizer Module (SKIM) can be pro- turned to the Off position for more than about fifty
grammed to recognize up to six additional seconds.
transponders, for a total of eight Sentry Keys. The
following “Customer Learn” programming procedure
for the programming of additional transponders REMOVAL AND INSTALLATION
requires access to at least two of the valid Sentry
Keys. If two valid Sentry Keys are not available, Sen- SENTRY KEY IMMOBILIZER MODULE
try Key programming will require the use of a DRB
scan tool and the proper Diagnostic Procedures man- WARNING: ON VEHICLES EQUIPPED WITH AIR-
ual. BAGS, REFER TO GROUP 8M - PASSIVE RESTRAINT
SYSTEMS BEFORE ATTEMPTING ANY STEERING
CUSTOMER LEARN WHEEL, STEERING COLUMN, OR INSTRUMENT
(1) Obtain the additional Sentry Key transponder PANEL COMPONENT DIAGNOSIS OR SERVICE. FAIL-
blank(s) that are to be programmed for the vehicle. URE TO TAKE THE PROPER PRECAUTIONS COULD
Cut the additional Sentry Key transponder blanks to RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND
match the ignition lock cylinder mechanical key POSSIBLE PERSONAL INJURY.
codes.
(2) Insert one of the two valid Sentry Key tran- (1) Disconnect and isolate the battery negative cable.
sponders into the ignition switch and turn the igni- (2) Remove the knee blocker from the instrument
tion switch to the On position. panel. See Knee Blocker in Group 8E - Instrument
(3) After the ignition switch has been in the On Panel Systems for the procedures.
position for about three seconds, but no more than (3) Remove the three screws that secure the lower
fifteen seconds later, cycle the ignition switch back to steering column shroud to the upper shroud (Fig. 2).
the Off position. Replace the first valid Sentry Key in
the ignition lock cylinder with the second valid Sen-
try Key and turn the ignition switch back to the On
position.
(4) About ten seconds after the completion of Step
3, the SKIS indicator lamp will start to flash and a
single audible chime tone will sound to indicate that
the system has entered the “Customer Learn” pro-
gramming mode.
(5) Within about fifty seconds of entering the “Cus-
tomer Learn” programming mode, turn the ignition
switch to the Off position, replace the valid Sentry
Key with a blank Sentry Key transponder, and turn
the ignition switch back to the On position.
(6) About ten seconds after the completion of Step
5, a single audible chime tone will sound and the
SKIS indicator lamp will stop flashing and stay on
solid for about three seconds to indicate that the
blank Sentry Key transponder has been successfully
programmed. The SKIS will immediately return to
normal system operation following exit from the
“Customer Learn” programming mode.
(7) Go back to Step 2 and repeat this process for
each additional Sentry Key transponder blank to be
programmed.
Fig. 3 Sentry Key Immobilizer Module Remove/Install

(4) If the vehicle is equipped with a standard non- on the connector end of the SKIM mounting bracket
tilt steering column, loosen the two upper steering to release this clip from the steering column jacket.
column mounting nuts. If the vehicle is equipped (9) Rotate the SKIM and its mounting bracket
with the optional tilt steering column, move the tilt downwards and then to the side away from the steer-
steering column to the fully lowered position. ing column to slide the SKIM antenna ring from
(5) Remove both the upper and lower shrouds from around the ignition switch lock cylinder housing.
the steering column. (10) Remove the SKIM from the vehicle.
(6) Disengage the steering column wire harness (11) Reverse the removal procedures to install.
retainer from the tab on the top of the Sentry Key Tighten the non-tilt steering column mounting nuts
Immobilizer Module (SKIM) mounting bracket (Fig. to 22 N·m (200 in. lbs.) and the steering column
3). shroud mounting screws to 2 N·m (18 in. lbs.).
(7) Unplug the wire harness connector from the (12) If the SKIM is replaced with a new unit, a
SKIM receptacle. DRB scan tool and the proper Diagnostic Procedures
(8) The SKIM mounting bracket features a clip for- manual MUST be used to initialize the new SKIM
mation that secures the SKIM to the inboard lower and to program at least two Sentry Key transponders.
flange of the steering column jacket. Pull downward
TJ CHIME/BUZZER WARNING SYSTEMS 8U - 1
CHIME/BUZZER WARNING SYSTEMS

CONTENTS
page page

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1 DRIVER DOOR JAMB SWITCH . . . . . . . . . . . . . 2
DESCRIPTION AND OPERATION DRIVER SEAT BELT SWITCH . . . . . . . . . . . . . . . 2
DRIVER DOOR JAMB SWITCH . . . . . . . . . . . . . 1 HEADLAMP SWITCH . . . . . . . . . . . . . . . . . . . . . 3
DRIVER SEAT BELT SWITCH . . . . . . . . . . . . . . . 2 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . . . . 3
HEADLAMP SWITCH . . . . . . . . . . . . . . . . . . . . . 2 KEY-IN IGNITION SWITCH . . . . . . . . . . . . . . . . . 3
INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . . . . 1 REMOVAL AND INSTALLATION
KEY-IN IGNITION SWITCH . . . . . . . . . . . . . . . . . 2 CHIME WARNING SYSTEM SWITCHES . . . . . . . 4
GENERAL INFORMATION chime tone generator to perform the functions of the

chime warning module on this model. The instru-
INTRODUCTION ment cluster circuitry also has a self-diagnostic capa-
This group covers the chime warning system, bility. Refer to Group 8E - Instrument Panel Systems
which is standard factory-installed equipment on this for more information on this feature.
model. The chime warning system provides an audi- Hard-wired chime warning system inputs to the
ble warning to the driver under the following condi- instrument cluster include the following:
tions: • Driver door jamb switch
• Check gauges lamp illumination • Driver seat belt switch
• Driver side seat belt is not fastened with the • Headlamp switch
ignition switch in the On position • Key-in ignition switch.
• Head or park lamps are turned on with the igni- The only instrument cluster diagnosis found in this
tion switch Off and the driver side front door open group consists of confirming the viability of the hard-
• Key is in the ignition switch with the ignition wired chime request inputs to the instrument cluster
switch Off and the driver side front door open circuitry. For diagnosis of the CCD data bus and the
• Low fuel warning lamp illumination - less than data bus message inputs, a DRB scan tool and the
about one-eighth tank of fuel remaining proper Diagnostic Procedures manual are recom-
• The optional Sentry Key Immobilizer System mended.
(SKIS) is in the “customer programming” mode. Refer to Group 8E - Instrument Panel Systems for
Following are general descriptions of the major the instrument cluster service procedures. The
components in the chime warning system. Refer to instrument cluster chime warning circuitry and
8W-40 Instrument Cluster or 8W-44 - Interior Light- chime tone generator cannot be repaired and, if
ing in Group 8W - Wiring Diagrams for complete cir- faulty or damaged, the instrument cluster assembly
cuit descriptions and diagrams. must be replaced.
DRIVER DOOR JAMB SWITCH

DESCRIPTION AND OPERATION The driver door jamb switch is mounted to the
driver side door hinge pillar. The switch closes a path
INSTRUMENT CLUSTER to ground for the instrument cluster chime warning
The instrument cluster is an electromechanical circuitry through the key-in ignition switch and/or
unit that contains integrated circuitry and internal the headlamp switch when the driver door is opened,
programming to perform a variety of functions. The and opens the ground path when the driver door is
instrument cluster circuitry monitors hard-wired closed.
switch inputs, as well as message inputs received The driver door jamb switch cannot be repaired
from other vehicle electronic modules on the Chrysler and, if faulty or damaged, it must be replaced. Refer
Collision Detection (CCD) data bus network. to Group 8L - Lamps for the service procedures.
The instrument cluster uses these many inputs
along with its internal programming and an integral
8U - 2 CHIME/BUZZER WARNING SYSTEMS TJ
DRIVER SEAT BELT SWITCH BAG DEPLOYMENT AND POSSIBLE PERSONAL

The driver seat belt switch is integral to the driver INJURY.
seat belt buckle-half assembly. The switch is nor-
(1) Rotate the headlamp switch knob counterclock-
mally closed, providing a ground path to the instru-
wise to ensure that the dome lamps are not switched
ment panel chime warning circuitry. When the tip-
off. Open the driver door and note whether the inte-
half of the seat belt is inserted into the seat belt
rior lamps light. They should light. If OK, see the
buckle, the switch opens the ground path.
diagnosis for the Key-In Ignition Switch or the Head-
The driver seat belt switch cannot be repaired and,
lamp Switch in this group. If not OK, go to Step 2.
if faulty or damaged, the entire driver seat belt buck-
le-half unit must be replaced. Refer to Group 23 -
cable. Unplug the driver door jamb switch from its
Body for the service procedures.
wire harness connector. Check for continuity between
the door jamb switch output circuit cavity of the
KEY-IN IGNITION SWITCH
driver door jamb switch wire harness connector and
The key-in ignition switch is integral to the igni-
a good ground. There should be continuity. If OK, go
tion switch, which is mounted on the left side of the
to Step 3. If not OK, repair the circuit to ground as
steering column, opposite the ignition lock cylinder.
required.
It closes a path to ground for the instrument cluster
(3) Check for continuity between the door jamb
chime warning circuitry when the ignition key is
switch output circuit terminal and the left front door
inserted in the ignition lock cylinder and the driver
jamb switch sense terminal of the door jamb switch.
door jamb switch is closed (driver door is open). The
There should be continuity with the switch plunger
key-in ignition switch opens the ground path when
released, and no continuity with the switch plunger
the key is removed from the ignition lock cylinder.
depressed. If not OK, replace the faulty switch.
The key-in ignition switch cannot be repaired and,
if faulty or damaged, the entire ignition switch must
be replaced. Refer to Group 8D - Ignition Systems for
DRIVER SEAT BELT SWITCH
the service procedures.
8W-40 - Instrument Cluster or 8W-44 - Interior
Lighting in Group 8W - Wiring Diagrams.
HEADLAMP SWITCH
The headlamp switch is located in the instrument WARNING: ON VEHICLES EQUIPPED WITH AIR-
panel, outboard of the steering column. It closes a BAGS, REFER TO GROUP 8M - PASSIVE
path to ground for the instrument cluster chime RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
warning circuitry when the park or head lamps are STEERING WHEEL, STEERING COLUMN, OR
on and the driver door jamb switch is closed (driver INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
door is open). The headlamp switch opens the ground SERVICE. FAILURE TO TAKE THE PROPER PRE-
path when the headlamp switch is turned off. CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
The headlamp switch cannot be repaired and, if BAG DEPLOYMENT AND POSSIBLE PERSONAL
faulty or damaged, it must be replaced. Refer to INJURY.
Group 8E - Instrument Panel Systems for the service
procedures. (1) Disconnect and isolate the battery negative
cable. Unplug the driver seat belt switch wire har-
ness connector on the floor under the driver seat
DIAGNOSIS AND TESTING near the seat belt buckle-half anchor. Check for con-
tinuity between the seat belt switch sense circuit and
DRIVER DOOR JAMB SWITCH the ground circuit cavities of the seat belt half of the
For circuit descriptions and diagrams, refer to driver seat belt switch wire harness connector. There
8W-40 - Instrument Cluster or 8W-44 - Interior should be continuity with the seat belt unbuckled,
Lighting in Group 8W - Wiring Diagrams. and no continuity with the seat belt buckled. If OK,
go to Step 2. If not OK, replace the faulty seat belt
buckle-half assembly.
cuit cavity in the body half of the driver seat belt
switch wire harness connector and a good ground.
There should be continuity. If OK, see the Instru-
ment Cluster diagnosis in this group. If not OK,
repair the circuit to ground as required.
TJ CHIME/BUZZER WARNING SYSTEMS 8U - 3
KEY-IN IGNITION SWITCH between the left front door jamb switch sense circuit
For circuit descriptions and diagrams, refer to cavity of the headlamp switch wire harness connector
8W-40 - Instrument Cluster or 8W-44 - Interior and a good ground. There should be no continuity
Lighting in Group 8W - Wiring Diagrams. with the driver door closed, and continuity with the
driver door open. If OK, go to Step 2. If not OK,
WARNING: ON VEHICLES EQUIPPED WITH AIR- repair the circuit to the driver door jamb switch as
BAGS, REFER TO GROUP 8M - PASSIVE required.
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY (2) Check for continuity between the key-in switch
STEERING WHEEL, STEERING COLUMN, OR sense circuit terminal and the left front door jamb
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR switch sense terminal of the headlamp switch. There
SERVICE. FAILURE TO TAKE THE PROPER PRE- should be no continuity with the switch in the Off
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- position, and continuity with the switch in the park
BAG DEPLOYMENT AND POSSIBLE PERSONAL or head lamps On position. If OK, see the diagnosis
INJURY. for the Instrument Cluster in this group. If not OK,
replace the faulty headlamp switch.
cable. Remove the steering column shrouds. Refer to INSTRUMENT CLUSTER
Group 8D - Ignition Systems for the procedures. Before performing this test, complete the testing of
Unplug the key-in ignition switch wire harness con- the hard-wired chime warning system switches as
nector from the ignition switch. described in this group. For circuit descriptions and
(2) Check for continuity between the key-in switch diagrams, refer to 8W-40 - Instrument Cluster or
sense circuit and the left front door jamb switch 8W-44 - Interior Lighting in Group 8W - Wiring Dia-
sense circuit terminals of the key-in ignition switch. grams.
There should be continuity with the key in the igni-
tion lock cylinder, and no continuity with the key WARNING: ON VEHICLES EQUIPPED WITH AIR-
removed from the ignition lock cylinder. If OK, go to BAGS, REFER TO GROUP 8M - PASSIVE
Step 3. If not OK, replace the faulty ignition switch RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
assembly. STEERING WHEEL, STEERING COLUMN, OR
(3) Check for continuity between the left front door INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
jamb switch sense circuit cavity of the key-in ignition SERVICE. FAILURE TO TAKE THE PROPER PRE-
switch wire harness connector and a good ground. CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
There should be continuity with the driver door open, BAG DEPLOYMENT AND POSSIBLE PERSONAL
and no continuity with the driver door closed. If OK, INJURY.
see the diagnosis for Instrument Cluster in this
group. If not OK, repair the circuit to the driver door (1) Disconnect and isolate the battery negative
jamb switch as required. cable. Remove the instrument cluster from the
instrument panel. Refer to Group 8E - Instrument
HEADLAMP SWITCH Panel Systems for the procedures.
For circuit descriptions and diagrams, refer to (2) Unplug the headlamp switch and the key-in
8W-40 - Instrument Cluster or 8W-44 - Interior ignition switch wire harness connectors. Check for
Lighting in Group 8W - Wiring Diagrams. continuity between the key-in switch sense circuit
cavity of the right instrument cluster wire harness
WARNING: ON VEHICLES EQUIPPED WITH AIR- connector (connector B) and a good ground. There
BAGS, REFER TO GROUP 8M - PASSIVE should be no continuity. If OK, go to Step 3. If not
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY OK, repair the short circuit as required.
STEERING WHEEL, STEERING COLUMN, OR (3) Check for continuity between the key-in switch
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR sense circuit cavities of the right instrument cluster
SERVICE. FAILURE TO TAKE THE PROPER PRE- wire harness connector (connector B) and the head-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- lamp switch wire harness connector. There should be
BAG DEPLOYMENT AND POSSIBLE PERSONAL continuity. If OK, go to Step 4. If not OK, repair the
INJURY. open circuit as required.
(4) Unplug the driver seat belt switch wire har-
(1) Disconnect and isolate the battery negative ness connector. Check for continuity between the seat
cable. Remove the headlamp switch from the instru- belt switch sense circuit cavity of the right instru-
ment panel. Refer to Group 8E - Instrument Panel ment cluster wire harness connector (connector B)
Systems for the procedures. Unplug the headlamp and a good ground. There should be no continuity. If
switch wire harness connectors. Check for continuity
8U - 4 CHIME/BUZZER WARNING SYSTEMS TJ
OK, go to Step 5. If not OK, repair the short circuit • Driver door jamb switch - refer to Group 8L -
as required. Lamps
(5) Check for continuity between the seat belt • Driver seat belt switch - refer to Group 23 -
switch sense circuit cavities of the right instrument Body
cluster wire harness connector (connector B) and the • Headlamp switch - refer to Group 8E - Instru-
driver seat belt switch wire harness connector. There ment Panel Systems
should be continuity. If OK, test the instrument clus- • Key-in ignition switch - refer to Group 8D - Igni-
ter as described in Group 8E - Instrument Panel Sys- tion Systems.
tems. If not OK, repair the open circuit as required.

CHIME WARNING SYSTEM SWITCHES
Service procedures for the various hard-wired
switches used in the chime warning system can be
found in the proper group as follows:
TJ WIRING DIAGRAMS 8W - 1
WIRING DIAGRAMS
CONTENTS
page page
AIR CONDITIONING-HEATER . . . . . . . . . . 8W-42-1 HORN/CIGAR LIGHTER/POWER OUTLET . 8W-41-1

AIRBAG SYSTEM . . . . . . . . . . . . . . . . . . . 8W-43-1 INSTRUMENT CLUSTER . . . . . . . . . . . . . . 8W-40-1
ANTI-LOCK BRAKES . . . . . . . . . . . . . . . . . 8W-35-1 INTERIOR LIGHTING . . . . . . . . . . . . . . . . . 8W-44-1
AUDIO SYSTEM . . . . . . . . . . . . . . . . . . . . 8W-47-1 POWER DISTRIBUTION . . . . . . . . . . . . . . 8W-10-1
CHARGING SYSTEM . . . . . . . . . . . . . . . . . 8W-20-1 REAR LIGHTING . . . . . . . . . . . . . . . . . . . . 8W-51-1
COMPONENT INDEX . . . . . . . . . . . . . . . . . 8W-02-1 REAR WINDOW DEFOGGER . . . . . . . . . . . 8W-48-1
CONNECTOR PIN-OUTS . . . . . . . . . . . . . . 8W-80-1 SPLICE INFORMATION . . . . . . . . . . . . . . . 8W-70-1
CONNECTOR/GROUND LOCATIONS . . . . . 8W-90-1 SPLICE LOCATIONS . . . . . . . . . . . . . . . . . 8W-95-1
FRONT LIGHTING . . . . . . . . . . . . . . . . . . . 8W-50-1 STARTING SYSTEM . . . . . . . . . . . . . . . . . 8W-21-1
FUEL/IGNITION SYSTEMS . . . . . . . . . . . . 8W-30-1 TRANSMISSION CONTROL SYSTEM . . . . 8W-31-1
FUSE/FUSE BLOCK . . . . . . . . . . . . . . . . . . 8W-11-1 TURN SIGNALS . . . . . . . . . . . . . . . . . . . . . 8W-52-1
GENERAL INFORMATION . . . . . . . . . . . . . 8W-01-1 WIPERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-53-1
GROUND DISTRIBUTION . . . . . . . . . . . . . 8W-15-1
TJ 8W - 01 GENERAL INFORMATION 8W - 01 - 1
8W-01 GENERAL INFORMATION
INDEX
page page
DESCRIPTION AND OPERATION TROUBLESHOOTING TESTS . . . . . . . . . . . . . . . . 9

CIRCUIT FUNCTIONS . . . . . . . . . . . . . . . . . .... 4 TROUBLESHOOTING TOOLS . . . . . . . . . . . . . . . 8
CIRCUIT INFORMATION . . . . . . . . . . . . . . . .... 4 TROUBLESHOOTING WIRING PROBLEMS . . . . 10
CONNECTOR INFORMATION . . . . . . . . . . . .... 7 SERVICE PROCEDURES
ELECTROSTATIC DISCHARGE (ESD) CONNECTOR AND TERMINAL REPLACEMENT . 12
SENSITIVE DEVICES . . . . . . . . . . . . . . . . . . . . 8 CONNECTOR REPLACEMENT . . . . . . . . . . . . . . 11
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1 DIODE REPLACEMENT . . . . . . . . . . . . . . . . . . . 14
NOTES, CAUTIONS, and WARNINGS . . . . . . . . . 7 TERMINAL REPLACEMENT . . . . . . . . . . . . . . . . 13
SECTION IDENTIFICATION . . . . . . . . . . . . . . . . . 5 TERMINAL/CONNECTOR REPAIR-MOLEX
SPLICE LOCATIONS . . . . . . . . . . . . . . . . . . . . . . 7 CONNECTORS . . . . . . . . . . . . . . . . . . . . . . . . 10
SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 TERMINAL/CONNECTOR REPAIR—THOMAS
TAKE OUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AND BETTS CONNECTORS . . . . . . . . . . . . . . 11
TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . . 7 WIRING REPAIR . . . . . . . . . . . . . . . . . . . . . . . . 10
DIAGNOSIS AND TESTING SPECIAL TOOLS
INTERMITTENT AND POOR CONNECTIONS .... 9 WIRING/TERMINAL . . . . . . . . . . . . . . . . . . . . . . 15
DESCRIPTION AND OPERATION Components are shown two ways. A solid line
around a component indicates that the component is
INTRODUCTION complete. A dashed line around a component indi-
Chrysler wiring diagrams are designed to provide cates that the component being shown is not com-
information regarding the vehicles wiring content. In plete. Incomplete components have a reference
order to effectively use Chrysler wiring diagrams to number to indicate the page where the component is
diagnose and repair a Chrysler vehicle, it is impor- shown complete.
tant to understand all of their features and charac- It is important to realize that no attempt is made
teristics. on the diagrams to represent components and wiring
Diagrams are arranged such that the power (B+) as they appear on the vehicle. For example, a short
side of the circuit is placed near the top of the page, piece of wire is treated the same as a long one. In
and the ground (B-) side of the circuit is placed near addition, switches and other components are shown
the bottom of the page. as simply as possible, with regard to function only.
All switches, components, and modules are shown
in the at rest position with the doors closed and the
key removed from the ignition.
8W - 01 - 2 8W - 01 GENERAL INFORMATION TJ
The System shown here is an EXAMPLE ONLY. It does not represent the actual circuit shown in the WIRING
DIAGRAM SECTION.
The System shown here is an EXAMPLE ONLY. It does not represent the actual circuit shown in the WIRING
DIAGRAM SECTION.
CIRCUIT INFORMATION CIRCUIT FUNCTIONS

Each wire shown in the diagrams contains a code All circuits in the diagrams use an alpha/numeric
which identifies the main circuit, part of the main code to identify the wire and its function. To identify
circuit, gage of wire, and color (Fig. 1). which circuit code applies to a system, refer to the
Circuit Identification Code Chart. This chart shows
the main circuits only and does not show the second-
ary codes that may apply to some models.
CIRCUIT IDENTIFICATION CODE CHART
CIRCUIT FUNCTION
A BATTERY FEED
B BRAKE CONTROLS
C CLIMATE CONTROLS
D DIAGNOSTIC CIRCUITS
E DIMMING ILLUMINATION CIRCUITS
F FUSED CIRCUITS
G MONITORING CIRCUITS (GAUGES)
Fig. 1 Wire Code Identification H OPEN

I NOT USED
WIRE COLOR CODE CHART
J OPEN
STANDARD K POWERTRAIN CONTROL MODULE
COLOR CODE COLOR TRACER L EXTERIOR LIGHTING
COLOR M INTERIOR LIGHTING
BL BLUE WT N NOT USED
BK BLACK WT O NOT USED
BR BROWN WT P POWER OPTION (BATTERY FEED)
DB DARK BLUE WT Q POWER OPTIONS (IGNITION FEED)
DG DARK GREEN WT R PASSIVE RESTRAINT
GY GRAY BK S SUSPENSION/STEERING
LB LIGHT BLUE BK T TRANSMISSION/TRANSAXLE/
LG LIGHT GREEN BK TRANSFER CASE
OR ORANGE BK U OPEN
PK PINK BK or WT V SPEED CONTROL, WIPER/WASHER
RD RED WT W OPEN
TN TAN WT X AUDIO SYSTEMS
VT VIOLET WT Y OPEN
WT WHITE BK Z GROUNDS
YL YELLOW BK
* WITH TRACER
SECTION IDENTIFICATION SYMBOLS

The wiring diagrams are grouped into individual International symbols are used throughout the wir-
sections. If a component is most likely found in a par- ing diagrams. These symbols are consistent with
ticular group, it will be shown complete (all wires, those being used around the world
connectors, and pins) within that group. For exam-
ple, the Auto Shutdown Relay is most likely to be
found in Group 30, so it is shown there complete. It
can, however, be shown partially in another group if
it contains some associated wiring.
GROUP TOPIC
8W-01 thru 8W-09 General Information and
Diagram Overview
8W-10 thru 8W-19 Main Sources of Power and
Vehicle Grounding
8W-20 thru 8W-29 Starting and Charging
8W-30 thru 8W-39 Powertrain/Drivetrain
Systems
8W-40 thru 8W-49 Body Electrical items and A/C
8W-50 thru 8W-59 Exterior Lighting, Wipers, and
Trailer Tow
8W-60 thru 8W-69 Power Accessories
8W-70 Splice Information
8W-80 Connector Pin Outs
8W-90 Connector Locations
(including grounds)
8W-95 Splice Locations
Wiring Diagram Symbols

TERMINOLOGY
This a list of terms with there definitions used in
the wiring diagrams.
Built-Up-Export . . . . . . . . Vehicles Built For Sale In

Markets Other Than North America
Except-Built-Up-Export . . Vehicles Built For Sale In
North America
LHD . . . . . . . . . . . . . . . . . Left Hand Drive Vehicles
RHD . . . . . . . . . . . . . . . . Right Hand Drive Vehicles
ATX . . . Automatic Transmission-Front Wheel Drive Fig. 3 Connector Identification
MTX . . . . Manual Transmission-Front Wheel Drive LOCATIONS
AT . . . . . Automatic Transmission-Rear Wheel Drive Section 8W-90 contains connector/ground location
MT . . . . . . Manual Transmission-Rear Wheel Drive illustrations. The illustrations contain the connector
SOHC . . . . . . . . . . . Single Over Head Cam Engine name (or number)/ground number and component
DOHC . . . . . . . . . . . . Dual Over Head Cam Engine identification. Connector/ground location charts in
Section 8W-90 reference the illustration number for
CONNECTOR INFORMATION components and connectors.
Section 8W-80 shows each connector and the cir-
CAUTION: Not all connectors are serviced. Some
cuits involved with that connector. The connectors
connectors are serviced only with a harness. A typ-
are identified using the name/number on the Dia-
ical example might be the Supplemental Restraint
gram pages.
System connectors. Always check parts availability
before attempting a repair.
SPLICE LOCATIONS
Splice Location charts in Section 8W-70 show the
IDENTIFICATION entire splice, and provide references to other sections
In-line connectors are identified by a number, as the splice serves.
follows: Section 8W-95 contains illustrations that show the
• In-line connectors located on the engine com- general location of the splices in each harness. The
partment harness are C100 series numbers. illustrations show the splice by number, and provide
• Connectors located on the instrument panel a written location.
harness are C200 series numbers.
• Connectors located on the body harness are NOTES, CAUTIONS, and WARNINGS
C300 series numbers. Throughout this group additional important infor-
• Jumper harness connectors are C400 series mation is presented in three ways; Notes, Cautions,
numbers. and Warnings.
• Grounds and ground connectors are identi- NOTES are used to help describe how switches or
fied with a “G” and follow the same series number- components operate to complete a particular circuit.
ing as the in-line connector. They are also used to indicate different conditions
Component connectors are identified by the compo- that may appear on the vehicle. For example, an
nent name instead of a number (Fig. 2). Multiple up-to and after condition.
connectors on a component use a C1, C2, etc. identi- CAUTIONS are used to indicate information that
fier (Fig. 3). could prevent making an error that may damage the
vehicle.
WARNINGS provide information to prevent per-
sonal injury and vehicle damage. Below is a list of
general warnings that should be followed any time a
vehicle is being serviced.
WARNING: ALWAYS WEAR SAFETY GLASSES FOR

EYE PROTECTION.
WARNING: USE SAFETY STANDS ANYTIME A PRO-

Fig. 2 Component Identification CEDURE REQUIRES BEING UNDER A VEHICLE.
WARNING: BE SURE THAT THE IGNITION SWITCH (3) When using a voltmeter, be sure to connect the
ALWAYS IS IN THE OFF POSITION, UNLESS THE ground lead first.
PROCEDURE REQUIRES IT TO BE ON. (4) Do not remove the part from its protective
packing until it is time to install the part.
(5) Before removing the part from its package,
WARNING: SET THE PARKING BRAKE WHEN ground the package to a known good ground on the
WORKING ON ANY VEHICLE. AN AUTOMATIC vehicle.
TRANSMISSION SHOULD BE IN PARK. A MANUAL
TRANSMISSION SHOULD BE IN NEUTRAL.
WARNING: OPERATE THE ENGINE ONLY IN A

WELL-VENTILATED AREA.
WARNING: KEEP AWAY FROM MOVING PARTS

WHEN THE ENGINE IS RUNNING, ESPECIALLY THE
FAN AND BELTS.
WARNING: TO PREVENT SERIOUS BURNS, AVOID Fig. 4 Electrostatic Discharge Symbol

CONTACT WITH HOT PARTS SUCH AS THE RADIA-
TOR, EXHAUST MANIFOLD(S), TAIL PIPE, CATA- DIAGNOSIS AND TESTING
LYTIC CONVERTER, AND MUFFLER.
TROUBLESHOOTING TOOLS
When diagnosing a problem in an electrical circuit
WARNING: DO NOT ALLOW FLAME OR SPARKS there are several common tools necessary. These tools
NEAR THE BATTERY. GASES ARE ALWAYS are listed and explained below.
PRESENT IN AND AROUND THE BATTERY. • Jumper Wire - This is a test wire used to con-
nect two points of a circuit. It can be used to bypass
an open in a circuit.
WARNING: ALWAYS REMOVE RINGS, WATCHES,
LOOSE HANGING JEWELRY, AND LOOSE CLOTH- WARNING: NEVER USE A JUMPER WIRE ACROSS
ING. A LOAD, SUCH AS A MOTOR, CONNECTED
BETWEEN A BATTERY FEED AND GROUND.
TAKE OUTS • Voltmeter - Used to check for voltage on a cir-
The abbreviation T/O is used in the component cuit. Always connect the black lead to a known good
location section to indicate a point in which the wir- ground and the red lead to the positive side of the
ing harness branches out to a component. circuit.
ELECTROSTATIC DISCHARGE (ESD) SENSITIVE CAUTION: Most of the electrical components used
DEVICES in today’s vehicle are solid state. When checking
All ESD sensitive components are solid state and a voltages in these circuits use a meter with a 10-me-
symbol (Fig. 4) is used to indicate this. When han- gohm or greater impedance rating.
dling any component with this symbol comply with
the following procedures to reduce the possibility of • Ohmmeter - Used to check the resistance
electrostatic charge build up on the body and inad- between two points of a circuit. Low or no resistance
vertent discharge into the component. If it is not in a circuit means good continuity.
known whether the part is ESD sensitive, assume
CAUTION: - Most of the electrical components used
that it is.
in today’s vehicle are Solid State. When checking
(1) Always touch a known good ground before han-
resistance in these circuits use a meter with a
dling the part. This should be repeated while han-
10-megohm or greater impedance rating. In addi-
dling the part and more frequently after sliding
tion, make sure the power is disconnected from the
across a seat, sitting down from a standing position,
circuit. Circuits that are powered up by the vehicle
or walking a distance.
electrical system can cause damage to the equip-
(2) Avoid touching electrical terminals of the part,
ment and provide false readings.
unless instructed to do so by a written procedure.
• Probing Tools - These tools are used for probing
terminals in connectors (Fig. 5). Select the proper
size tool from Special Tool Package 6807, and insert
it into the terminal being tested. Use the other end
of the tool to insert the meter probe.
Fig. 5 Probing Tool

INTERMITTENT AND POOR CONNECTIONS
Most intermittent electrical problems are caused
by faulty electrical connections or wiring. It is also
possible for a sticking component or relay to cause a
Fig. 6 Testing for Voltage Potential
problem. Before condemning a component or wiring
assembly check the following items. TESTING FOR CONTINUITY
• Connectors are fully seated (1) Remove the fuse for the circuit being checked
• Spread terminals, or terminal push out or, disconnect the battery.
• Terminals in the wiring assembly are fully (2) Connect one lead of the ohmmeter to one side
seated into the connector/component and locked in of the circuit being tested (Fig. 7).
position (3) Connect the other lead to the other end of the
• Dirt or corrosion on the terminals. Any amount circuit being tested. Low or no resistance means good
of corrosion or dirt could cause an intermittent prob- continuity.
lem
• Damaged connector/component casing exposing
the item to dirt and moisture
• Wire insulation that has rubbed through causing
a short to ground
• Some or all of the wiring strands broken inside
of the insulation covering.
• Wiring broken inside of the insulation
TROUBLESHOOTING TESTS
Before beginning any tests on a vehicles electrical
system use the Wiring Diagrams and study the cir-
cuit. Also refer to the Troubleshooting Wiring Prob-
lems in this section.
TESTING FOR VOLTAGE POTENTIAL

(1) Connect the ground lead of a voltmeter to a
known good ground (Fig. 6).
(2) Connect the other lead of the voltmeter to the
selected test point. The vehicle ignition may need to
be turned ON to check voltage. Refer to the appropri-
ate test procedure.
Fig. 7 Testing for Continuity
TESTING FOR A SHORT TO GROUND TROUBLESHOOTING WIRING PROBLEMS
(1) Remove the fuse and disconnect all items When troubleshooting wiring problems there are
involved with the fuse. six steps which can aid in the procedure. The steps
(2) Connect a test light or a voltmeter across the are listed and explained below. Always check for non-
terminals of the fuse. factory items added to the vehicle before doing any
(3) Starting at the fuse block, wiggle the wiring diagnosis. If the vehicle is equipped with these items,
harness about six to eight inches apart and watch disconnect them to verify these add-on items are not
the voltmeter/test lamp. the cause of the problem.
(4) If the voltmeter registers voltage or the test (1) Verify the problem.
lamp glows, there is a short to ground in that gen- (2) Verify any related symptoms. Do this by per-
eral area of the wiring harness. forming operational checks on components that are
in the same circuit. Refer to the wiring diagrams.
TESTING FOR A SHORT TO GROUND ON FUSES (3) Analyze the symptoms. Use the wiring dia-
POWERING SEVERAL LOADS grams to determine what the circuit is doing, where
(1) Refer to the wiring diagrams and disconnect or the problem most likely is occurring and where the
isolate all items on the suspected fused circuits. diagnosis will continue.
(2) Replace the blown fuse. (4) Isolate the problem area.
(3) Supply power to the fuse by turning ON the (5) Repair the problem.
ignition switch or re-connecting the battery. (6) Verify proper operation. For this step check for
(4) Start connecting the items in the fuse circuit proper operation of all items on the repaired circuit.
one at a time. When the fuse blows the circuit with Refer to the wiring diagrams.
the short to ground has been isolated.
TESTING FOR A VOLTAGE DROP SERVICE PROCEDURES

(1) Connect the positive lead of the voltmeter to
the side of the circuit closest to the battery (Fig. 8). WIRING REPAIR
(2) Connect the other lead of the voltmeter to the When replacing or repairing a wire, it is important
other side of the switch or component. that the correct gage be used as shown in the wiring
(3) Operate the item. diagrams. The wires must also be held securely in
(4) The voltmeter will show the difference in volt- place to prevent damage to the insulation.
age between the two points. (1) Disconnect battery negative cable.
(2) Remove 1 inch of insulation from each end of
the wire.
(3) Place a piece of heat shrink tubing over one
side of the wire. Make sure the tubing will be long
enough to cover and seal the entire repair area.
(4) Spread the strands of the wire apart on each
part of the exposed wire (example 1) (Fig. 9).
(5) Push the two ends of wire together until the
strands of wire are close to the insulation (example
2) (Fig. 9).
(6) Twist the wires together (example 3) (Fig. 9).
(7) Solder the connection together using rosin core
type solder only. Do not use acid core solder.
(8) Center the heat shrink tubing over the joint,
and heat using a heat gun. Heat the joint until the
tubing is tightly sealed and sealant comes out of both
ends of the tubing.
(9) Secure the wire to the existing ones to prevent
chafing or damage to the insulation.
(10) Connect battery and test all affected systems.
TERMINAL/CONNECTOR REPAIR-MOLEX
Fig. 8 Testing for Voltage Drop CONNECTORS
(1) Disconnect battery.
Fig. 11 Using Special Tool 6742

(2) Disconnect the connector from its mating half/
component.
(3) Push in the two lock tabs on the side of the
connector (Fig. 12).
Fig. 9 Wire Repair

(2) Disconnect the connector from its mating half/
component.
(3) Insert the terminal releasing special tool 6742
into the terminal end of the connector (Fig. 10).
Fig. 12 Thomas and Betts Connector Lock Release

Tabs
(4) Insert the probe end of special tool 6934 into
the back of the connector cavity (Fig. 13).
(5) Grasp the wire and tool 6934 and slowly
remove the wire and terminal from the connector.
Fig. 10 Molex Connector Repair (6) Repair or replace the terminal.
(4) Using special tool 6742 release the locking fin- (7) Install the wire and terminal in the connector.
gers on the terminal (Fig. 11). Fully seat the terminal in the connector.
(5) Pull on the wire to remove it from the connec- (8) Push in the single lock tab on the side of the
tor. connector (Fig. 14).
(6) Repair or replace the connector or terminal, as
necessary. CONNECTOR REPLACEMENT
TERMINAL/CONNECTOR REPAIR—THOMAS (2) Disconnect the connector that is to be repaired
AND BETTS CONNECTORS from its mating half/component.
(1) Disconnect battery. (3) Remove the connector locking wedge, if
required (Fig. 15).
(4) Position the connector locking finger away from
the terminal using the proper pick from special tool
kit 6680. Pull on the wire to remove the terminal
from the connector (Fig. 16) (Fig. 17).
(5) Reset the terminal locking tang, if it has one.
(6) Insert the removed wire in the same cavity on
the repair connector.
(7) Repeat steps four through six for each wire in
the connector, being sure that all wires are inserted
into the proper cavities. For additional connector pin-
out identification, refer to the wiring diagrams.
(8) Insert the connector locking wedge into the
repaired connector, if required.
(9) Connect connector to its mating half/compo-
nent.
(10) Connect battery and test all affected systems.
Fig. 13 Removing Wire Terminal
Fig. 16 Terminal Removal
Fig. 14 Single Lock Tab
Fig. 17 Terminal Removal Using Special Tool

CONNECTOR AND TERMINAL REPLACEMENT
(2) Disconnect the connector (that is to be
Fig. 15 Connector Locking Wedge
repaired) from its mating half/component.
(3) Cut off the existing wire connector directly (3) Remove connector locking wedge, if required
behind the insulator. Remove six inches of tape from (Fig. 19).
the harness.
(4) Stagger cut all wires on the harness side at 1/2
inch intervals (Fig. 18).
(5) Remove 1 inch of insulation from each wire on
the harness side.
(6) Stagger cut the matching wires on the repair
connector assembly in the opposite order as was done
on the harness side of the repair. Allow extra length
for soldered connections. Check that the overall
length is the same as the original (Fig. 18).
Fig. 19 Connector Locking Wedge Tab (Typical)

(4) Position the connector locking finger away from
the terminal using the proper pick from special tool
kit 6680. Pull on the wire to remove the terminal
from the connector (Fig. 20) (Fig. 21).
Fig. 18 Stagger Cutting Wires

(7) Remove 1 inch of insulation from each wire.
(8) Place a piece of heat shrink tubing over one
side of the wire. Be sure the tubing will be long
enough to cover and seal the entire repair area.
(9) Spread the strands of the wire apart on each
part of the exposed wires.
(10) Push the two ends of wire together until the
strands of wire are close to the insulation.
(11) Twist the wires together.
(12) Solder the connection together using rosin
core type solder only. Do not use acid core solder.
(13) Center the heat shrink tubing over the joint Fig. 20 Terminal Removal
and heat using a heat gun. Heat the joint until the (5) Cut the wire 6 inches from the back of the con-
tubing is tightly sealed and sealant comes out of both nector.
ends of the tubing. (6) Remove 1 inch of insulation from the wire on
(14) Repeat steps 8 through 13 for each wire. the harness side.
(15) Re-tape the wire harness starting 1-1/2 inches (7) Select a wire from the terminal repair assem-
behind the connector and 2 inches past the repair. bly that best matches the color wire being repaired.
(16) Re-connect the repaired connector. (8) Cut the repair wire to the proper length and
(17) Connect the battery, and test all affected sys- remove 1 inch of insulation.
tems. (9) Place a piece of heat shrink tubing over one
side of the wire. Make sure the tubing will be long
TERMINAL REPLACEMENT enough to cover and seal the entire repair area.
(1) Disconnect battery. (10) Spread the strands of the wire apart on each
(2) Disconnect the connector being repaired from part of the exposed wires.
its mating half. Remove connector locking wedge, if (11) Push the two ends of wire together until the
required (Fig. 19). strands of wire are close to the insulation.
DIODE REPLACEMENT
(1) Disconnect the battery.
(2) Locate the diode in the harness, and remove
the protective covering.
(3) Remove the diode from the harness, pay atten-
tion to the current flow direction (Fig. 22).
Fig. 21 Terminal Removal Using Special Tool

(12) Twist the wires together.
(13) Solder the connection together using rosin
core type solder only. Do not use acid core solder.
(14) Center the heat shrink tubing over the joint
and heat using a heat gun. Heat the joint until the
tubing is tightly sealed and sealant comes out of both Fig. 22 Diode Identification
ends of the tubing.
(15) Insert the repaired wire into the connector. (4) Remove the insulation from the wires in the
(16) Install the connector locking wedge, if harness. Only remove enough insulation to solder in
required, and reconnect the connector to its mating the new diode.
half/component. (5) Install the new diode in the harness, making
(17) Re-tape the wire harness starting 1-1/2 inches sure current flow is correct. If necessary refer to the
behind the connector and 2 inches past the repair. appropriate wiring diagram for current flow.
(18) Connect battery, and test all affected systems. (6) Solder the connection together using rosin core
type solder only. Do not use acid core solder.
(7) Tape the diode to the harness using electrical
tape making, sure the diode is completely sealed
from the elements.
(8) Re-connect the battery, and test affected sys-
tems.
SPECIAL TOOLS
WIRING/TERMINAL
Terminal Removing Tool 6932
Probing Tool Package 6807
Terminal Removing Tool 6934
Terminal Pick 6680

TJ 8W - 02 COMPONENT INDEX 8W - 02 - 1
8W-02 COMPONENT INDEX

Component Page Component Page
A/C Compressor Clutch . . . . . . . . . . . . . . . . . 8W-42 Fuel Pump Relay . . . . . . . . . . . . . . . . . . . . . . 8W-30
A/C Compressor Clutch Relay . . . . . . . . . . . . 8W-42 Fuse Block . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11
A/C Heater Control . . . . . . . . . . . . . . . . . . . . 8W-42 Fuses (FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11
A/C Pressure Switches . . . . . . . . . . . . . . . 8W-30, 42 Fuses (PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10
ABS Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-35 Fusible Link . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20
ABS Pump Motor . . . . . . . . . . . . . . . . . . . . . . 8W-35 Fusible Link A11 . . . . . . . . . . . . . . . . . . . . . . 8W-10
ABS Pump Motor Relay . . . . . . . . . . . . . . . . . 8W-35 G-Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-35
ABS System Relay . . . . . . . . . . . . . . . . . . . . . 8W-35 Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40
Airbag Control Module . . . . . . . . . . . . . . . . . . 8W-43 Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20
Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-43 Grounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15
Automatic Shut Down Relay . . . . . . . . . . . . . 8W-30 Headlamp Dimmer Switch . . . . . . . . . . . . . . . 8W-50
Back-Up Lamp Switch . . . . . . . . . . . . . . . . . . 8W-51 Headlamp Leveling Motor . . . . . . . . . . . . . . . 8W-50
Back-Up Lamps . . . . . . . . . . . . . . . . . . . . . . . 8W-51 Headlamp Leveling Switch . . . . . . . . . . . . . . 8W-50
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20 Headlamp Switch . . . . . . . . . . . . . . . . . . . . . . 8W-50
Battery Temperature Sensor . . . . . . . . . . . . . 8W-30 Headlamps . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50
Blend Door Actuator . . . . . . . . . . . . . . . . . . . 8W-42 Horn Relay . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-41
Blower Motor . . . . . . . . . . . . . . . . . . . . . . . . . 8W-42 Horn Switch . . . . . . . . . . . . . . . . . . . . . . . 8W-30, 41
Blower Motor Relay . . . . . . . . . . . . . . . . . . . . 8W-42 Horns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-41
Brake Indicator Switch . . . . . . . . . . . . . . . . . 8W-51 HVAC Unit . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-42
Brake Lamps . . . . . . . . . . . . . . . . . . . . . . . . . 8W-51 Hydraulic Control Unit . . . . . . . . . . . . . . . . . 8W-35
Brake Shift Interlock Solenoid . . . . . . . . . . . . 8W-31 Idle Air Control Motor . . . . . . . . . . . . . . . . . . 8W-30
Brake Warning Indicator Switch . . . . . . . . . . 8W-40 Ignition Coil . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-30
Camshaft Position Sensor . . . . . . . . . . . . . . . 8W-30 Ignition Switch . . . . . . . . . . . . . . . . . . . . . . . 8W-10
Center High Mounted Stop Lamp . . . . . . . . . 8W-51 Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40
Cigar Lighter/Accessory Relay . . . . . . . . . . . . 8W-41 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 8W-40
Cigar Lighter/Power Outlet . . . . . . . . . . . . . . 8W-41 Intake Air Temperature Sensor . . . . . . . . . . . 8W-30
Circuit Breaker . . . . . . . . . . . . . . . . . . . . 8W-50, 51 Internal Delay Relay . . . . . . . . . . . . . . . . . . . 8W-53
City Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50 Key-In Switch . . . . . . . . . . . . . . . . . . . . . 8W-40, 44
Clockspring . . . . . . . . . . . . . . . . . . . . . . . 8W-30, 43 Leak Detection Pump . . . . . . . . . . . . . . . . . . 8W-30
Cluster Illumination Lamps . . . . . . . . . . . . . . 8W-40 License Lamps . . . . . . . . . . . . . . . . . . . . . . . . 8W-51
Clutch Pedal Position Switch . . . . . . . . . . . . . 8W-21 Manifold Absolute Pressure Sensor . . . . . . . . 8W-30
Clutch Pedal Position Switch Connector . . . . 8W-21 Manual Transmission Jumper . . . . . . . . . 8W-21, 30
Combination Flasher . . . . . . . . . . . . . . . . . . . 8W-52 Mercury Switch . . . . . . . . . . . . . . . . . . . . . . . 8W-44
Controller Anti-Lock Brake . . . . . . . . . . . . . . 8W-35 Odometer/Trip Odometer . . . . . . . . . . . . . . . . 8W-40
Courtesy Lamps . . . . . . . . . . . . . . . . . . . . . . . 8W-44 Oxygen Sensors . . . . . . . . . . . . . . . . . . . . . . . 8W-30
Crankshaft Position Sensor . . . . . . . . . . . . . . 8W-30 Park Brake Switch . . . . . . . . . . . . . . . . . . . . . 8W-40
Data Link Connector . . . . . . . . . . . . . . . . . . . 8W-30 Park/Neutral Position Switch . . . . . . . . . . 8W-21, 51
Daytime Running Lamp Module . . . . . . . . . . 8W-50 Park/Turn Signal Lamps . . . . . . . . . . . . . 8W-50, 52
Dome Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44 Park/Turn Signal Indicators . . . . . . . . . . . 8W-50, 52
Driver Door Ajar Switch . . . . . . . . . . . . . . . . 8W-44 Passenger Airbag On/Off Switch . . . . . . . . . . 8W-43
Duty Cycle Evap/Purge Solenoid . . . . . . . . . . 8W-30 Passenger Door Ajar Switch . . . . . . . . . . . . . . 8W-44
Engine Coolant Temperature Sensor . . . . . . . 8W-30 Power Distribution Center . . . . . . . . . . . . . . . 8W-10
Engine Oil Pressure Sensor . . . . . . . . . . . . . . 8W-30 Power Steering Pressure Switch . . . . . . . . . . 8W-30
Engine Starter Motor . . . . . . . . . . . . . . . . . . . 8W-21 Powertrain Control Module . . . . . . . . . . . . . . 8W-30
Engine Starter Motor Relay . . . . . . . . . . . . . . 8W-21 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . . . . . 8W-44
Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50 Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-47
Fog Lamp Illumination . . . . . . . . . . . . . . . . . 8W-51 Radio Antenna . . . . . . . . . . . . . . . . . . . . . . . . 8W-47
Fog Lamp Indicator . . . . . . . . . . . . . . . . . . . . 8W-51 Rear Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . 8W-51
Fog Lamp Relays . . . . . . . . . . . . . . . . . . . . . . 8W-50 Rear Fog Lamp Relay . . . . . . . . . . . . . . . . . . 8W-51
Front Fog Lamp Switch . . . . . . . . . . . . . . . . . 8W-50 Rear Fog Lamp Switch . . . . . . . . . . . . . . . . . 8W-51
Fuel Injectors . . . . . . . . . . . . . . . . . . . . . . . . . 8W-30 Rear Lamp Assemblies . . . . . . . . . . . . . . . . . . 8W-51
Fuel Pump Module . . . . . . . . . . . . . . . . . . . . 8W-30 Rear Washer Pump . . . . . . . . . . . . . . . . . . . . 8W-53
8W - 02 - 2 8W - 02 COMPONENT INDEX TJ

Rear Window Defogger . . . . . . . . . . . . . . . . . 8W-48 Tail/Stop Lamps . . . . . . . . . . . . . . . . . . . . . . . 8W-51
Rear Window Defogger Relay . . . . . . . . . . . . . 8W-48 Throttle Position Sensor . . . . . . . . . . . . . . . . 8W-30
Rear Window Defogger Switch . . . . . . . . . . . . 8W-48 Torque Converter Clutch Solenoid . . . . . . 8W-30, 31
Rear Wiper Motor . . . . . . . . . . . . . . . . . . . . . 8W-53 Transfer Case Switch . . . . . . . . . . . . . . . . . . . 8W-31
Rear Wiper/Washer Switch . . . . . . . . . . . . . . 8W-53 Trip Odometer Reset Switch . . . . . . . . . . . . . 8W-40
Repeater Lamps . . . . . . . . . . . . . . . . . . . . . . . 8W-52 Turn Signal Lamps . . . . . . . . . . . . . . . . . . . . 8W-52
Seat Belt Switch . . . . . . . . . . . . . . . . . . . . . . 8W-40 Turn Signal/Hazard Switch . . . . . . . . . . . 8W-51, 52
Sentry Key Immobilizer Module . . . . . . . . . . 8W-30 Underhood Lamp . . . . . . . . . . . . . . . . . . . . . . 8W-44
Side Marker Lamps . . . . . . . . . . . . . . . . . 8W-50, 52 Vehicle Speed Control Servo . . . . . . . . . . . . . 8W-30
Sound Bar Dome Lamp . . . . . . . . . . . . . . . . . 8W-44 Vehicle Speed Sensor . . . . . . . . . . . . . . . . . . . 8W-30
Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-47 Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40
Speed Control Switch Pod . . . . . . . . . . . . . . . 8W-30 Wheel Speed Sensors . . . . . . . . . . . . . . . . . . . 8W-35
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40 Windshield Washer Pump . . . . . . . . . . . . . . . 8W-53
Splice Information . . . . . . . . . . . . . . . . . . . . . 8W-70 Windshield Wiper Motor . . . . . . . . . . . . . . . . 8W-53
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40 Windshield Wiper Switch . . . . . . . . . . . . . . . . 8W-53
Tail/Stop/Turn Signal Lamps . . . . . . . . . . 8W-51, 52
TJ 8W - 10 POWER DISTRIBUTION 8W - 10 - 1
8W-10 POWER DISTRIBUTION

A/C Compressor Clutch . . . . . . . . . . . . . . . 8W-10-16 Fuse 14 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 17
A/C Compressor Clutch Relay . . . . . . . . . . 8W-10-16 Fuse 15 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9
ABS Diode . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-17 Fuse 15 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 14
ABS Pump Motor . . . . . . . . . . . . . . . . . . . 8W-10-17 Fuse 16 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 16
ABS Pump Motor Relay . . . . . . . . . . . . . . 8W-10-17 Fuse 17 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-10-14
ABS System Relay . . . . . . . . . . . . . . . . . . 8W-10-17 Fuse 17 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 16
Automatic Shut Down Relay . . . . . . . . . . . 8W-10-11 Fuse 18 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-10-10
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-6 Fuse 18 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-10-11
Brake Warning Indicator Switch . . . . . . . . . 8W-10-9 Fuse 19 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-10-10
Cigar Lighter/Accessory Relay . . . . . . . 8W-10-9, 10 Fuse 19 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 14
Clutch Pedal Position Switch . . . . . . . . . . . 8W-10-8 Fuse 20 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-8
Controller Anti-Lock Brake . . . . . . . . . . . . 8W-10-17 Fuse 20 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 15
Data Link Connector . . . . . . . . . . . . . . . . . 8W-10-15 Fuse 21 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 17
Dome Lamp . . . . . . . . . . . . . . . . . . . . . . . 8W-10-15 Fuse 25 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 16
Engine Starter Motor . . . . . . . . . . . . . . . 8W-10-6, 8 Fuse 27 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 11
Engine Starter Motor Relay . . . . . . . . . . . . 8W-10-8 Fuse Block . . . . . . . . . . . . . . . . . . 8W-10-8, 9, 10, 14
Fog Lamp Relay No. 1 . . . . . . . . . . . . . . . 8W-10-16 Fusible Link A11 . . . . . . . . . . . . . . . . . . . . . 8W-10-6
Fuel Injector No. 1 . . . . . . . . . . . . . . . . . . 8W-10-12 G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9
Fuel Injector No. 2 . . . . . . . . . . . . . . . . . . 8W-10-12 Generator . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-6
Fuel Injector No. 3 . . . . . . . . . . . . . . . . . . 8W-10-12 Headlamp Switch . . . . . . . . . . . . . . . . . . . 8W-10-13
Fuel Injector No. 4 . . . . . . . . . . . . . . . . . . 8W-10-12 High Note Horn . . . . . . . . . . . . . . . . . . . . 8W-10-16
Fuel Injector No. 5 . . . . . . . . . . . . . . . . . . 8W-10-12 Horn Relay . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-16
Fuel Injector No. 6 . . . . . . . . . . . . . . . . . . 8W-10-12 HVAC Unit . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-13
Fuel Pump Module . . . . . . . . . . . . . . . . . . 8W-10-14 Hydraulic Control Unit . . . . . . . . . . . . . . . 8W-10-17
Fuel Pump Relay . . . . . . . . . . . . . . . . . . . 8W-10-14 Ignition Coil . . . . . . . . . . . . . . . . . . . . . . . 8W-10-12
Fuse 1 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-10 Ignition Switch . . . . . . . . . . . . . . . . . . . . 8W-10-8, 9
Fuse 2 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-10 Instrument Cluster . . . . . . . . . . . . . . . . . . 8W-10-15
Fuse 2 (PDC) . . . . . . . . . . . . . . . . . . . . . 8W-10-6, 8 Leak Detection Pump . . . . . . . . . . . . . . . . 8W-10-11
Fuse 3 (PDC) . . . . . . . . . . . . . . . . . . . . . 8W-10-6, 9 Left Courtesy Lamp . . . . . . . . . . . . . . . . . 8W-10-15
Fuse 4 (PDC) . . . . . . . . . . . . . . . . . . . . . 8W-10-6, 10 Left Fog Lamp . . . . . . . . . . . . . . . . . . . . . 8W-10-16
Fuse 5 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-8 Low Note Horn . . . . . . . . . . . . . . . . . . . . . 8W-10-16
Fuse 5 (PDC) . . . . . . . . . . . . . . . . . . . . . 8W-10-6, 10 Oxygen Sensor 1/1 Upstream . . . . . . . . . . 8W-10-11
Fuse 6 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-8 Oxygen Sensor 1/2 Downstream . . . . . . . . 8W-10-11
Fuse 6 (PDC) . . . . . . . . . . . . . . . . . . . . . 8W-10-6, 11 Park Brake Switch . . . . . . . . . . . . . . . . . . . 8W-10-9
Fuse 7 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-8 Power Distribution Center . . 8W-10-2, 6, 7, 8, 9, 10,
Fuse 8 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-8 11, 13, 14, 15, 16, 17
Fuse 9 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9 Powertrain Control Module . . . . . . . . . . . . 8W-10-11
Fuse 9 (PDC) . . . . . . . . . . . . . . . . . . . . . 8W-10-6, 13 Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-15
Fuse 10 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9 Rear Window Defogger . . . . . . . . . . . . . . . 8W-10-14
Fuse 10 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-6, 13 Rear Window Defogger Relay . . . . . . . . . . 8W-10-14
Fuse 11 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9 Right Courtesy Lamp . . . . . . . . . . . . . . . . 8W-10-15
Fuse 11 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-6, 13 Right Fog Lamp . . . . . . . . . . . . . . . . . . . . 8W-10-16
Fuse 12 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9 Sound Bar Dome Lamp . . . . . . . . . . . . . . . 8W-10-15
Fuse 13 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9 Turn Signal/Hazard Switch . . . . . . . . . . . . 8W-10-13
Fuse 13 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-10-7, 17 Underhood Lamp . . . . . . . . . . . . . . . . . . . 8W-10-15
Fuse 14 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9
8W - 10 - 2 8W-10 POWER DISTRIBUTION TJ
POWER DISTRIBUTION CENTER
13 6
D
ENGINE REAR
STARTER 14 12 10 8 5 2 WINDOW
MOTOR DEFOGGER
RELAY RELAY
11 4
13 9 6 3
C ABS
ABS
SYSTEM 10 2 PUMP
14 12 8 5
RELAY MOTOR
RELAY
11 7 4 1
A/C FUEL
COMPRESSOR PUMP
CLUTCH RELAY
RELAY B
AUTOMATIC
SHUT HORN
DOWN RELAY
RELAY
1 2 7 8 13 14 19 20
A 3 4 9 10 15 16 21 22
5 6 11 12 17 18 23 24
FUSES
8 15
7 14 21 28
40A
7 14
6 13 20 27
40A
6 13
5 12 19 26
30A 30A
5 12
4 11 18 25
40A
4 11
3 10 17 24
40A 40A
3 10
2 9 16 23
30A 30A
2 9
1 8 15 22
40A 20A
+ M1
J998W-5 TJI01002
TJ 8W-10 POWER DISTRIBUTION 8W - 10 - 3
FUSES
FUSE NO. AMPS FUSED CIRCUIT FEED CIRCUIT

A2 12PK/BK
2 40A A0 6RD
A2 12PK/BK
3 30A A1 14RD A0 6RD
4 40A A6 12RD/BK A0 6RD
5 40A F30 12RD/PK A0 6RD
A14 14RD/WT
6 30A A0 6RD
A14 14RD/WT
7 - - A0 6RD
8 - - A0 6RD
9 20A L9 16BK/WT A0 6RD
10 30A A3 14RD/WT A0 6RD
11 40A A111 12RD/LB A0 6RD
12 - - A0 6RD
13 30A A20 14RD/DB A0 6RD
14 40A A10 12RD/DG A0 6RD
15 40A A4 12BK/PK A0 6RD
16 10A A17 20RD/GY A0 6RD
F31 18VT
17 20A A0 6RD
F31 18VT
18 20A F42 18DG/LG A142 14DG/PK
19 20A A61 18DG/BK A0 6RD
20 10A M1 20PK/WT A0 6RD
21 10A B47 14RD/LB B48 20RD/YL
22 - -
23 - -
24 - -
25 20A F61 18WT/OR A0 6RD
26 - -
27 10A F142 20OR/DG A142 14DG/PK
TJI01003 J998W-5
CAVITY CIRCUIT FUNCTION

C1 - -
C2 A10 12RD/DG FUSED B (+)
ABS C3 Z1 14BK GROUND

PUMP B47 14RD/LB ABS SYSTEM RELAY OUTPUT
MOTOR C4
RELAY B47 14RD/LB ABS SYSTEM RELAY OUTPUT
C5 - -
C6 B116 20GY ABS PUMP MOTOR RELAY CONTROL
C7 - -
C8 B120 12BR/WT ABS PUMP MOTOR RELAY OUTPUT
C9 - -

ABS C10 B47 14RD/LB ABS SYSTEM RELAY OUTPUT
SYSTEM F20 20VT/WT FUSED IGNITION SWITCH OUTPUT (RUN)
C11
RELAY
C12 Z1 14BK GROUND
C13 B58 20GY/LB ABS SYSTEM RELAY CONTROL
C14 A20 14RD/DB FUSED B(+)

A/C B6 A17 20RD/GY FUSED B (+)
COMPRESSOR C3 20DB/BK A/C COMPRESSOR CLUTCH RELAY OUTPUT
B7
CLUTCH
RELAY B8 F20 20VT/WT FUSED IGNITION SWITCH OUTPUT (RUN)
B9 - -
B10 C13 18DB/OR A/C COMPRESSOR CLUTCH RELAY CONTROL

B1 A14 14RD/WT FUSED B (+)
AUTOMATIC
SHUT DOWN B2 A142 14DG/PK AUTOMATIC SHUT DOWN RELAY OUTPUT SENSE
RELAY F15 20DB FUSED IGNITION SWITCH OUTPUT (ST-RUN)
B3
B4 - -
B5 K51 18DB/YL AUTOMATIC SHUT DOWN RELAY CONTROL
J998W-5 TJI01004

D10 A2 12PK/BK FUSED B (+)
ENGINE
STARTER D11 T141 14YL/RD FUSED IGNITION SWITCH OUTPUT (ST)
MOTOR
D12 - -
RELAY
D13 T41 20BR/LB PARK/NEUTRAL POSITION SWITCH SENSE
D14 T40 12BR ENGINE STARTER MOTOR RELAY OUTPUT

B16 A61 18DG/BK FUSED B (+)
FUEL
PUMP B17 A141 18DG/WT FUEL PUMP RELAY OUTPUT
RELAY
B18 F15 20DB FUSED IGNITION SWITCH OUTPUT (ST-RUN)
B19 - -
B20 K31 18BR FUEL PUMP RELAY CONTROL

B11 F31 18VT FUSED B (+)
HORN
RELAY B12 X2 18WT/RD HORN RELAY OUTPUT
B13 F31 18VT FUSED B (+)
B14 - -
B15 X3 20RD/YL HORN RELAY CONTROL

REAR D2 A4 12BK/PK FUSED B (+)
WINDOW F20 20VT/WT FUSED IGNITION SWITCH OUTPUT (RUN)
D4
DEFOGGER
RELAY D5 - -
D6 C81 20LB/WT REAR WINDOW DEFOGGER RELAY CONTROL
D8 C15 12BK/WT REAR WINDOW DEFOGGER RELAY OUTPUT
TJI01005 J998W-5
S136
A0 A11
A0 6 FUSIBLE
6 6
RD LINK BK/GY
RD A11
BATTERY 10
(8W-20-2) DG
GENERATOR
(8W-20-2)
ENGINE
STARTER
MOTOR
(8W-21-2)
POWER
DISTRIBUTION
8 9 10 11
CENTER
FUSE FUSE FUSE FUSE (8W-10-2)
2 3 4 5
40A 30A 40A 40A
(8W-10-8) (8W-10-9) (8W-10-10) (8W-10-10)
1 2 3 4
A2
12
PK/BK
F5 F7 F1
F6 C106 C106
TO F30
A2 ENGINE A1 A6 12
12 14 12 RD/PK
PK/BK STARTER RD RD/BK
MOTOR
RELAY TO
TO (IN PDC) TO TO S332
IGNITION IGNITION FUSE
SWITCH SWITCH BLOCK
12 16
FUSE FUSE
6 10 17
30A 22 30A
(8W-10-13) FUSE
(8W-10-11) FUSE 23 A
5 11
9 40A
20A (8W-10-13) TO
(8W-10-13) 24 FUSE
15 13 (PDC)
(8W-10-7)
A111
12
A14 3 C103 D11 C108 4 C170 RD/LB
14
RD/WT A14 L9
16 A3
14 14 TO
RD/WT BK/WT
TO RD/WT C106
AUTOMATIC
TO
SHUT TO TO
POWERTRAIN TURN
DOWN HEADLAMP
CONTROL SIGNAL/
RELAY SWITCH
MODULE HAZARD
(IN PDC)
SWITCH
J998W-5 TJI01006
POWER
FROM DISTRIBUTION
FUSE CENTER
11 (PDC) (8W-10-2)
(8W-10-6)
A
19 20 21 A23 A21
FUSE FUSE FUSE FUSE FUSE
13 14 15 16 17
30A 40A 40A 10A 20A
(8W-10-17) (8W-10-17) (8W-10-14) (8W-10-16) (8W-10-16)
26 27 28 A24 A22
A17
A10 A4 20 F31 F31
12 12 RD/GY 18 18
A20
RD/DG BK/PK VT VT
14
RD/DB
TO TO TO
TO TO A/C HORN HORN
ABS REAR COMPRESSOR RELAY RELAY
PUMP WINDOW CLUTCH (IN PDC) (IN PDC)
TO
MOTOR DEFOGGER RELAY
ABS
RELAY RELAY (IN PDC)
SYSTEM FROM FROM
(IN PDC) (IN PDC)
RELAY S146 S101
(IN PDC)
B48 A142
20 14
RD/YL DG/PK
A14 A1
FUSE FUSE
A18 A16 A6 21 27
FUSE FUSE FUSE 10A 10A
19 20 25 (8W-10-17) (8W-10-11)
A13 A2
20A 10A 20A
(8W-10-14) (8W-10-15) (8W-10-16)
A17 A15 A5
B47
F61 14 F142
M1 18 RD/LB 20
A61 20 WT/OR
PK/WT OR/DG
18
DG/BK D6 C108 LEAK
TO DETECTION OTHER
TO F61 ABS
C108 18 PUMP F142 F142
TO
WT/OR MOTOR B47 20 20
FUEL OR/DG OR/DG
RELAY 14
PUMP RD/LB
TO (IN PDC)
RELAY
(IN PDC) FOG
TO TO
LAMP TO
S114 S107 C103
RELAY
NO. 1
TJI01007 J998W-5
BATT A0 (8W-10-6)
POWER
DISTRIBUTION
8 9
CENTER
FUSE FUSE (8W-10-2)
2 3
40A 30A
(8W-10-9)
1 2
A2
12 A2 A1
PK/BK 12 14
PK/BK RD
D10
F6 F5
ENGINE C106
STARTER
MOTOR A2 A1
RELAY 12 14
PK/BK RD
D14 (IN PDC)
(8W-21-2)
T40 3 3
12 IGNITION
BR SWITCH
LHD RHD 1 START
2 RUN
12 C104 6 C104 1 4 1 4 0 OFF
2 3 2 3 3 LOCK
0 0 4 ACC
(8W-10-9)
T40
12 4 10 8
BR
A41
ENGINE A22 14
STARTER 12 YL
BK/OR
MOTOR
(8W-21-2) S331
5 20
FUSE
BLOCK
(8W-11-2) A41
FUSE FUSE 14
6 8 YL
20A 10A
(8W-11-6) (8W-11-7)
FUSE FUSE FUSE
5 7 20
10A 10A 20A
(8W-11-6) (8W-11-7) (A/T)
(8W-11-9)
25 26 27 28 40
A/T M/T
2 2
NOT CLUTCH CLUTCH
USED PEDAL PEDAL
POSITION POSITION
SWITCH SWITCH
CONNECTOR (8W-21-2)
J998W-5 TJI01008
BATT A0 PARK
(8W-10-6)
BRAKE
POWER SWITCH
DISTRIBUTION (8W-40-6)
9
CENTER
(8W-10-2) BRAKE
FUSE
3
G9 WARNING
20 INDICATOR
30A
GY/BK
2 SWITCH
LHD RHD 1 (8W-40-6)
G9 C322 9 C322
A1
14
G9
RD
20
BATT A2 GY/BK
G9
(8W-10-8) F5 C106 20
GY/BK F11 C106
A2 A1 G9
12 14 20
PK/BK RD GY/BK
3 7 2
IGNITION
SWITCH
1 START
1 4 1 4 1 4 1 4 2 RUN
2 3 2 3 2 3 2 3 0 OFF
0 0 0 0 3 LOCK
4 ACC
4 9 10 8 1
A22 A21 A41 A31 Z1
12 14 14 14 16
BK/OR DB YL BK/DG BK
S307
RUN A22 A31 A31 S304

14 14 (8W-15-9)
(8W-10-8) BK/DG BK/DG (8W-15-10)
2 Z1
16
ST A41 CIGAR BK
LIGHTER/
(8W-10-8) ACCESSORY
G300
RELAY (8W-15-9)
5 (8W-41-2) (8W-15-10)
9 13
FUSE
BLOCK
(8W-11-2)
FUSE FUSE
10 12
10A 10A
(8W-11-8) (8W-11-8)

9 11 13 14 15
10A 10A 10A 20A 10A
(8W-11-8) (8W-11-8) (8W-11-9) (8W-11-9) (8W-11-9)
29 30 31 32 33 34 35
TJI01009 J998W-5
BATT A0 (8W-10-6)
POWER
DISTRIBUTION
10 11
CENTER
(8W-10-2)
FUSE FUSE
4 5
40A 40A
3 4
A6 F30
12 12
RD/BK RD/PK
F1 C106
F30
12
RD/PK
S332
F7 C106 F30
12
RD/PK
1
CIGAR
LIGHTER/
ACCESSORY
RELAY
4 (8W-41-2)
A6 F22 F30
12 12 12
RD/BK WT/PK RD/PK
1 19 18
FUSE
BLOCK
(8W-11-2)
FUSE FUSE FUSE FUSE
1 2 19 18
20A 20A 20A 15A
(8W-11-4) (8W-11-4) (8W-11-10) (8W-11-10)
21 22 39 38
J998W-5 TJI01010
BATT A0 (8W-10-6)
POWER
DISTRIBUTION
12 B1 CENTER
FUSE AUTOMATIC (8W-10-2)
6 SHUT A20 A2
30A DOWN FUSE FUSE
RELAY 18 27
5
(8W-30-2) 20A 10A
B2
A19 A1
A14 A14 A142 A142 A142 F142 F42

14 14 14 14 14 20 18
RD/WT RD/WT DG/PK DG/PK DG/PK OR/DG DG/LG
S101
LHD RHD
3 C103
A14 A142
11 C104 4 C104
14 14
RD/WT DG/PK
A22 C1 C12 C3 F42

18
POWERTRAIN DG/LG
CONTROL
MODULE B
(8W-30-2)
TO
S126
(8W-10-12)
LEAK
DETECTION OTHER
S107
F142
20
F142
OR/DG
20
OR/DG
3 C180 1 C103
F142
18
F142 OR/DG
20
OR/DG
S124
2
F142 F142
LEAK 18 18
DETECTION OR/DG OR/DG
PUMP
(EXCEPT BUILT-
UP-EXPORT) 1 1
(8W-30-11) OXYGEN OXYGEN
SENSOR SENSOR
1/2 1/1
DOWNSTREAM UPSTREAM
(8W-30-9) (8W-30-9)
TJI01011 J998W-5
FROM
C104
(8W-10-11)
B
F42
18
DG/LG
S126
F42 F42
18 18
DG/LG DG/LG
1
FUEL
INJECTOR
F42 NO. 6
18 (4.0L)
DG/LG
(8W-30-6)
F42
18
DG/LG
1
FUEL 1
F42 INJECTOR IGNITION
18 NO. 5 COIL
DG/LG
(4.0L) (2.5L)
(8W-30-4)
(8W-30-6)
1
FUEL
INJECTOR
NO. 4
F42
(8W-30-5)
18
(8W-30-6)
DG/LG
S128
1
FUEL
INJECTOR
NO. 3 F42
(8W-30-5) 18
(8W-30-6) DG/LG
1
FUEL
F42 INJECTOR F42
18 NO. 2 18
DG/LG (8W-30-5) DG/LG
(8W-30-6)
1 1
FUEL IGNITION
INJECTOR COIL
NO. 1 (4.0L)
(8W-30-5) (8W-30-4)
(8W-30-6)
J998W-5 TJI01012
BATT A0 (8W-10-6)
POWER
DISTRIBUTION
22 16 17
CENTER
FUSE FUSE FUSE (8W-10-2)
9 10 11
20A 30A 40A
15 23 24
A111
L9 A3 12
16 14 RD/LB
BK/WT RD/WT
F12 C106
A111
12
RD/LB
A12 C202
D11 C108 4 C170
A111
12
RD/LB
8
HVAC
L9 A3 UNIT
16 14 (8W-42-2)
BK/WT RD/WT (8W-42-3)
6 8
TURN HEADLAMP
SIGNAL/ SWITCH
HAZARD (8W-50-2)
SWITCH (8W-50-5)
(8W-52-2)
TJI01013 J998W-5
BATT A0 (8W-10-6)
POWER
DISTRIBUTION
21 A18
CENTER
FUSE FUSE (8W-10-2)
15 19
40A 20A
28 A17
A4 A61
12 18
BK/PK DG/BK
B16
D2 FUEL
REAR PUMP
WINDOW RELAY
DEFOGGER (IN PDC)
RELAY B17 (8W-30-3)
D8 (IN PDC) A141
(8W-48-2) 18
C15 DG/WT
12
BK/WT
7 C103
F8 C106
C15 A141
12 18
BK/WT DG/WT
S320
1
C15 FUEL
12 PUMP
BK/WT
MODULE
(8W-30-3)
LHD RHD
H1 C323 1 C323
1 C326
C15
12
BK/WT
C15 1 C331
14
BK/WT C15
12
17 BK/WT
FUSE
BLOCK
FUSE (8W-11-2) C15
17
12
10A
GY
(8W-11-9)
37 REAR
WINDOW
DEFOGGER
(HARD TOP)
(8W-48-2)
J998W-5 TJI01014
BATT A0 (8W-10-6)
INSTRUMENT
POWER CLUSTER
A16 DISTRIBUTION (8W-40-2)
FUSE CENTER
20 (8W-10-2)
9 C2
10A LEFT
A15 COURTESY
LAMP
M1 (8W-44-4)
20
PK/WT M1 DATA LINK
20 CONNECTOR
PK
D12 C108 (8W-30-13)
M1 1 16
20
PK/WT B7 C203
M1 M1 M1 M1
2 20 20 20 20
UNDERHOOD PK/WT PK/WT PK/WT PK/WT
LAMP
(8W-44-3) S204
M1
20 M1 M1
PK/WT 20 20
PK/WT PK/WT
HARD TOP SOFT TOP
7 C1
M1 M1 1 RADIO
20 20 (8W-47-2)
PK/WT M1
PK/WT
20
2 SPEAKER 4 SPEAKER
PK
SYSTEM SYSTEM
LHD RHD M1 RIGHT

20 COURTESY
M1
PK/WT LAMP
H2 C323 2 C323 20
(8W-44-4)
PK/WT
LHD RHD
LHD RHD
H2 C323 2 C323
M1 NOT
20 USED
NOT H2 C323 2 C323
PK/WT USED
2 SPEAKER 4 SPEAKER
SYSTEM SYSTEM M1
20
S313 PK/WT
8 C326 3 C325
8 C331 3 C330
M1 M1
20 20
PK/WT PK/WT
1
DOME SOUND
LAMP BAR
(8W-44-2) DOME
LAMP
(8W-44-2)
TJI01015 J998W-5
BATT A0 (8W-10-6)
POWER
DISTRIBUTION
A23 A21 A6 CENTER
16 17 25
10A 20A 20A
A24 A22 A5
A17
20 F61
RD/GY 18
WT/OR
B6 F31 F31
A/C 18 18 D6 C108
COMPRESSOR VT VT
CLUTCH F61
RELAY 18
(IN PDC) WT/OR
B7
(8W-42-4)
C3
20 B13 B11 3
DB/BK HORN FOG
RELAY LAMP
14 C103
(IN PDC) RELAY
C3
(8W-41-3) NO. 1
20 B15 B12 5 (8W-50-7)
DB/BK
X2 L39
18 18
1 WT/RD LB
A/C
COMPRESSOR E10 C107
CLUTCH 6 C110
(8W-42-4) L39
18
X2
LB
18
WT/RD
EXCEPT BUILT- 13 C110
BUILT-UP-EXPORT UP-EXPORT
L39
S115 18
LB
S116
X2 X2
18 18
L39 L39
WT/RD WT/RD
18 18
LB LB
1 1 2 2
LOW HIGH LEFT RIGHT
NOTE NOTE FOG FOG
HORN HORN LAMP LAMP
(8W-41-3) (8W-41-3) (8W-50-7) (8W-50-7)
J998W-5 TJI01016
ABS
DIODE
(8W-35-3)
A
S146
B48
20
RD/YL
BATT A0 (8W-10-6)
POWER
A14 DISTRIBUTION
FUSE CENTER
21 (8W-10-2)
10A
A13
19 20
FUSE FUSE
13 14
30A 40A
26 27
B47 A10
A20 14 12
14 RD/LB RD/DG
RD/DB
C10
ABS C4 C2
SYSTEM ABS
RELAY PUMP
(PDC) MOTOR
C14 C12 (8W-35-2) RELAY
C6 C8 C3 (PDC)
(8W-35-2)
B47 B47 B120
14 14 12 B48
RD/LB RD/LB BR/WT 20
RD/YL
S114 S110
B47 B47 B120 B120
14 14 12 12
RD/LB RD/LB BR/WT BR/WT
1 S112
ABS
PUMP
MOTOR B120
(8W-35-2) 16
BR/WT
10 1 3 C2 5 C2
HYDRAULIC CONTROLLER
CONTROL ANTI-LOCK
UNIT BRAKE
(8W-35-4) (8W-35-2)
(8W-35-3)
TJI01017 J998W-5
TJ 8W - 11 FUSE/FUSE BLOCK 8W - 11 - 1
8W-11 FUSE/FUSE BLOCK

A/C Compressor Clutch Relay . . . . . . . . . . . 8W-11-7 Fuse 14 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-9
A/C Heater Control . . . . . . . . . . . . . . . . . 8W-11-4, 7 Fuse 15 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-9
ABS System Relay . . . . . . . . . . . . . . . . . . . 8W-11-7 Fuse 16 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-11-10
Airbag Control Module . . . . . . . . . . . . . . 8W-11-6, 8 Fuse 17 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-9
Automatic Shut Down Relay . . . . . . . . . . . . 8W-11-8 Fuse 18 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-11-10
Back-Up Lamp Switch . . . . . . . . . . . . . . . . 8W-11-7 Fuse 19 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-11-10
Brake Lamp Switch . . . . . . . . . . . . . . . . . . 8W-11-4 Fuse 20 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-9
Brake Shift Interlock Solenoid . . . . . . . . . . 8W-11-8 Fuse Block . . . . . . . . . . . 8W-11-2, 4, 5, 6, 7, 8, 9, 10
Cigar Lighter/Accessory Relay . . . . . . . . . . 8W-11-10 G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-5
Cigar Lighter/Power Outlet . . . . . . . . . . . . 8W-11-10 Headlamp Dimmer Switch . . . . . . . . . . . . 8W-11-10
Clutch Pedal Position Switch . . . . . . . . . . . 8W-11-9 Headlamp Leveling Switch . . . . . . . . . . . . 8W-11-10
Clutch Pedal Position Switch Connector . . . 8W-11-9 Headlamp Switch . . . . . . . . . . . . . . . . . 8W-11-4, 10
Controller Anti-Lock Brake . . . . . . . . . . . . . 8W-11-7 HVAC Unit . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-7
Daytime Running Lamp Module . . . . . . . . . 8W-11-8 Instrument Cluster . . . . . . . . . . . . . . . . . 8W-11-4, 8
Driver Door Ajar Switch . . . . . . . . . . . . . . . 8W-11-5 Left Headlamp Leveling Motor . . . . . . . . . 8W-11-10
Duty Cycle Evap/Purge Solenoid . . . . . . . . . 8W-11-8 Park/Neutral Position Switch . . . . . . . . . . . 8W-11-7
Engine Starter Motor Relay . . . . . . . . . . . . 8W-11-9 Passenger Airbag On/Off Switch . . . . . . . . . 8W-11-8
Fog Lamp Relay No. 1 . . . . . . . . . . . . . . . . 8W-11-5 Passenger Door Ajar Switch . . . . . . . . . . . . 8W-11-5
Fog Lamp Relay No. 2 . . . . . . . . . . . . . . . . 8W-11-5 Powertrain Control Module . . . . . . . . . . . . . 8W-11-8
Front Fog Lamp Switch . . . . . . . . . . . . . . . 8W-11-4 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . . . . 8W-11-4
Fuel Pump Relay . . . . . . . . . . . . . . . . . . . . 8W-11-8 Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-4, 9
Fuse 1 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-4 Rear Fog Lamp Relay . . . . . . . . . . . . . . 8W-11-5, 10
Fuse 2 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-4 Rear Fog Lamp Switch . . . . . . . . . . . . . . . . 8W-11-4
Fuse 3 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-4 Rear Window Defogger Relay . . . . . . . . . 8W-11-7, 9
Fuse 4 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-5 Rear Window Defogger Switch . . . . . . . . 8W-11-4, 9
Fuse 5 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-6 Rear Wiper Motor . . . . . . . . . . . . . . . . . . . . 8W-11-6
Fuse 6 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-6 Rear Wiper/Washer Switch . . . . . . . . . . . 8W-11-4, 6
Fuse 7 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-7 Right Headlamp Leveling Motor . . . . . . . . 8W-11-10
Fuse 8 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-7 Sentry Key Immobilizer Module . . . . . . . 8W-11-4, 8
Fuse 9 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-8 Torque Converter Clutch Solenoid . . . . . . . . 8W-11-8
Fuse 10 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-8 Turn Signal/Hazard Switch . . . . . . . . . . . . . 8W-11-9
Fuse 11 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-8 Windshield Wiper Motor . . . . . . . . . . . . . . . 8W-11-9
Fuse 12 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-8 Windshield Wiper Switch . . . . . . . . . . . . . . 8W-11-9
Fuse 13 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-9
8W - 11 - 2 8W-11 FUSE/FUSE BLOCK TJ
FRONT OF
FUSE BLOCK
40 39 38 37
FUSE FUSE FUSE FUSE

20 19 18 17
20 19 18 17
36 35 34 33
FUSE FUSE FUSE FUSE

16 15 14 13
16 15 14 13
32 31 30 29
FUSE FUSE FUSE FUSE

12 11 10 9
12 11 10 9
28 27 26 25
FUSE FUSE FUSE FUSE

8 7 6 5
8 7 6 5
24 23 22 21
FUSE FUSE FUSE FUSE

4 3 2 1
4 3 2 1
J998W-5 TJI01102
TJ 8W-11 FUSE/FUSE BLOCK 8W - 11 - 3
FUSES
FUSE NO. AMPS FUSED CIRCUIT FEED CIRCUIT

1 20A F34 18TN/BK
A6 12RD/BK
2 20A F32 18PK/DB
E2 20OR
3 10A E1 18TN
E2 20OR
Z1 20BK M23 20YL/BK

4 10A
Z1 20BK M23 20YL/BK
5 10A F23 18DB/YL
6 20A V23 18BR/PK

A22 12BK/OR
7 10A F20 20VT/WT
8 10A F24 20RD/DG
F14 18LG/YL
9 10A
F14 18LG/YL
G5 20DB/WT
10 10A
G5 20DB/WT A21 14DB
11 10A F12 20RD/LG
F15 20DB
12 10A
F15 20DB
13 10A L5 20BK/GY
14 20A V6 18PK/BK A31 14BK/DG
15 10A X12 20PK
16 10A L22 20LG/DG L2 16LG
17 10A F81 20DB/RD C15 14BK/WT
18 15A A18 16RD/BK F30 12RD/PK
F38 16LB
19 20A F22 12WT/PK
F38 16LB
20 20A T141 14YL/RD A41 14YL
FRONT FOG LAMPS

REAR FOG LAMPS
A/T
TJI01103 J998W-5
HEADLAMP
SWITCH
(8W-50-2)
1
E1
18
TN
A3 C202
E1
18
TN
BATT A6 (8W-10-10)
3
FUSE
BLOCK
(8W-11-2)
FUSE FUSE FUSE
1 2 3
20A 20A 10A
21 22 23
F34 F32 E2
18 18 20
TN/BK PK/DB OR
5 1
A11 C202 BRAKE PRNDL
E2
F34 LAMP 20
LAMP
F34 20 SWITCH (8W-44-5)
OR
18 TN/BK (8W-51-6)
TN/BK
4 1 FRONT
HEADLAMP SENTRY FOG
SWITCH KEY A4 C202
LAMP
(8W-50-2) IMMOBILIZER SWITCH
(8W-50-4) MODULE 1 (EXCEPT
(8W-30-14) E2 BUILT-UP
20 -EXPORT)
E2
OR (8W-50-7)
20
OR
S206
E2 E2 E2 E2 E2
20 20 20 20 20
OR OR OR OR OR
4 3 4
REAR REAR REAR
WINDOW WIPER/ FOG
E2 DEFOGGER WASHER LAMP
20 SWITCH SWITCH SWITCH
OR
(HARD TOP) (HARD TOP) (BUILT-UP-
5 C1 (8W-48-2) 4 C2 (8W-53-4) EXPORT)
RADIO A/C- 3 C2 (8W-51-7)
(8W-47-2)
HEATER INSTRUMENT (8W-51-8)
CONTROL CLUSTER
(8W-42-2) (8W-40-8)
(8W-42-3)
J998W-5 TJI01104
DRIVER PASSENGER
DOOR DOOR
AJAR AJAR
SWITCH SWITCH
1 (8W-44-4) 1 (8W-44-4)
M23 M23
20 20
YL/BK YL/BK
4
FUSE
BLOCK
(8W-11-2)
FUSE
4
10A
1
24
FOG
LAMP
RELAY Z1 Z1
NO. 1 20 20
(EXCEPT BUILT- BK BK
2
UP-EXPORT)
(8W-50-7)
3
REAR
Z1 FOG
Z1 1 20
20 LAMP
FOG BK
BK RELAY
LAMP (BUILT-UP
RELAY -EXPORT)
NO. 2 (8W-51-7)
2 (EXCEPT BUILT- (8W-51-8)
UP-EXPORT)
(8W-50-6)
LHD RHD
S304
(8W-15-9)
Z1
20
Z1 BK
16
BK
G300
(8W-15-9)
(8W-15-10)
TJI01105 J998W-5
RUN A22 (8W-10-8)

FUSE
BLOCK
(8W-11-2)
FUSE FUSE
5 6
10A 20A
25 26
F23 V23
18 18
DB/YL BR/PK
LHD RHD
SOFT TOP SOFT TOP HARD TOP
V23 V23 V23

18 18 18
BR/PK BR/PK BR/PK
H4 C323 4 C323 LHD RHD

NOT NOT
USED USED H4 C323 4 C323
V23
18
BR/PK
5 C326
20
AIRBAG 5 C331
CONTROL
S401
MODULE
(8W-43-2) V23
4 C331
18
4 C326 BR/PK
1
V23 REAR
18 WIPER
BR/PK
MOTOR
(8W-53-4)
LHD RHD
G10 C322 10 C322
V23 V23
18 18
BR/PK BR/PK
C6 C204
V23
18
BR/PK
5
REAR
WIPER/
WASHER
SWITCH
(8W-53-4)
J998W-5 TJI01106
RUN A22 (8W-10-8)

FUSE
BLOCK
(8W-11-2)
FUSE FUSE
7 8
10A 10A
27 28
F20 F24
20 20
VT/WT RD/DG
F3 C106 A1 C202
F20 F24 F24

20 20 20
VT/WT RD/DG RD/DG
3 F24 20RD/DG
5 9
1 C2 HVAC
A/C- UNIT
HEATER (8W-42-2)
CONTROL (8W-42-3)
(8W-42-2)
(8W-42-3)
S108
F20 F20 F20 F20 F20

20 20 20 20 20
VT/WT VT/WT VT/WT VT/WT VT/WT
10 C104
C11
F20 ABS
20 SYSTEM
5 C1
VT/WT RELAY
CONTROLLER
(IN PDC)
A/T M/T ANTI-LOCK
C13 (8W-35-2)
BRAKE
F20 F20 (8W-35-3)
20 20 D4
VT/WT VT/WT REAR
WINDOW
4 C154 4 C154
DEFOGGER
F20 F20 RELAY
18 18
VT/WT VT/WT
B8 D6 (IN PDC)
A/C (8W-48-2)
1 B
COMPRESSOR
PARK/ BACK-UP
CLUTCH LHD
NEUTRAL LAMP
RELAY
POSITION SWITCH
B10 (IN PDC) RHD
SWITCH (8W-51-2)
(8W-42-4)
(8W-51-2) (8W-51-3)
TJI01107 (8W-51-3) J998W-5
ST-RUN A21 (8W-10-9)

FUSE
BLOCK
(8W-11-2)
FUSE FUSE FUSE FUSE
9 10 11 12
10A 10A 10A 10A
29 30 31 32
F12
F14 G5 G5 20 F15 F15
18 20 20 RD/LG 20 20
LG/YL DB/WT DB/WT DB DB
A10 C202 3
2 SENTRY F4 C106
BRAKE KEY
F14 G5
SHIFT F10 C106
18 20 IMMOBILIZER F15
LG/YL DB/WT INTERLOCK MODULE 20
SOLENOID (8W-30-14) DB
(8W-31-2)
S131
8 C2
INSTRUMENT F12 F15 F15 F15
CLUSTER 20 20 20 20
(8W-40-2) RD/LG DB DB DB
S102
F12 F12 F12 LHD RHD

20 20 20
1 C1 RD/LG RD/LG RD/LG 13
C104 7
C104
PASSENGER 9 C103
AIRBAG 5 B18
ON/OFF F12 DAYTIME FUEL
SWITCH 20 RUNNING PUMP
RD/LG
(8W-43-2) LAMP RELAY
MODULE (IN PDC)
(8W-50-8) (8W-30-3)
B20
B3
A AUTOMATIC
TORQUE SHUT
CONVERTER DOWN
CLUTCH RELAY
SOLENOID B5 (IN PDC)
F15 (8W-30-2)
(8W-31-2) 18
11 C110 DB
F12
20
17 RD/LG
AIRBAG 2
CONTROL DUTY A2 C1
MODULE CYCLE POWERTRAIN
(8W-43-2)
EVAP/ CONTROL
PURGE MODULE
(8W-30-2)
SOLENOID
(8W-30-11)
J998W-5 TJI01108
BATT A4 (8W-10-14)
REAR
WINDOW
DEFOGGER
RELAY
D8 (IN PDC) F8 C106
(8W-48-2)
C15
12
C15
BK/WT
12
BK/WT S320
(8W-10-14)
C15
14
BK/WT
RUN-ACC A31 (8W-10-9) ST A41 (8W-10-8)
17
FUSE
BLOCK
(8W-11-2)
13 14 15 17 20
10A 20A 10A 10A 20A
(A/T)
33 34 35 37 40
V6 A5 C202 T141
18 X12
20 14
PK/BK F81 YL/RD
L5 PK
20
20 S306 DB/RD
BK/GY C10 C204 F9 C106 T141
3
14
REAR YL/RD
V6 V6 X12
18 18 20
WINDOW
DEFOGGER M/T A/T
PK/BK PK/BK PK
SWITCH
6 C1 (HARD
RADIO TOP)
(8W-47-2)
(8W-48-2)
1
NOT CLUTCH
USED PEDAL
1 POSITION
WINDSHIELD SWITCH
WIPER CONNECTOR
MOTOR 1 (8W-21-2)
(8W-53-2) CLUTCH
(8W-53-3)
PEDAL
5
POSITION
WINDSHIELD
SWITCH
WIPER T141 (8W-21-2)
SWITCH 14
(8W-53-2) YL/RD
(8W-53-3)
5 D11
TURN ENGINE
SIGNAL/ STARTER
HAZARD MOTOR
SWITCH RELAY
(8W-52-2)
D13 (IN PDC)
(8W-21-2)
TJI01109 J998W-5
BATT F30 (8W-10-10) BATT A3 (8W-10-13)
CIGAR HEADLAMP
CIRCUIT SWITCH
LIGHTER/ BREAKER 0 OFF
ACCESSORY 24A 1 PARK
RELAY 2 HEAD
4 (8W-41-2) (8W-50-2)
F22
12 0 1 2
WT/PK
2
L2
16
LG
A8 C202
L2 14LG
2
HEADLAMP
L2 DIMMER
16 SWITCH
LG (8W-50-2)
BATT F30 (8W-10-10)
19 16
FUSE
BLOCK
18 19 16
15A 20A 10A
(BUILT-UP
-EXPORT)
38 39 36
F38 L22
16 20
LB LG/DG
A18 F38 A9 C202
16 16
RD/BK LB F38 S330
16
L22 L22 L22
LB
20 20 20
UNSWITCHED 1 LG/DG LG/DG LG/DG
AUXILIARY CIGAR
POWER
(TAPED TO LIGHTER/ L22 C9 C204 5 1
HARNESS IN POWER 20 REAR
SWITCHED LG/DG FOG
FB T/O) OUTLET
AUXILIARY D13 C108
POWER
(8W-41-2) LAMP
(TAPED TO L22 RELAY
HARNESS IN 20 L22 (8W-51-7)
FB T/O) LG/DG 20 (8W-51-8)
LG/DG
9 C110
L22
20
LG/DG
S151
1 1 2
LEFT RIGHT HEADLAMP
HEADLAMP HEADLAMP LEVELING
LEVELING LEVELING SWITCH
MOTOR MOTOR (8W-50-5)
(8W-50-5) (8W-50-5)
J998W-5 TJI01110
TJ 8W - 15 GROUND DISTRIBUTION 8W - 15 - 1
8W-15 GROUND DISTRIBUTION

A/C Compressor Clutch . . . . . . . . . . . . . . . . 8W-15-6 Ignition Switch . . . . . . . . . . . . . . . . . . . 8W-15-9, 10
A/C Heater Control . . . . . . . . . . . . . . . . . 8W-15-7, 8 Instrument Cluster . . . . . . . . . . . . . . . . . 8W-15-7, 8
ABS Pump Motor . . . . . . . . . . . . . . . . . . . . 8W-15-2 Left City Lamp . . . . . . . . . . . . . . . . . . . . . . 8W-15-3
ABS Pump Motor Relay . . . . . . . . . . . . . . . 8W-15-2 Left Fog Lamp . . . . . . . . . . . . . . . . . . . . . . 8W-15-3
ABS System Relay . . . . . . . . . . . . . . . . . . . 8W-15-2 Left Front Park/Turn Signal Lamp . . . . . . . 8W-15-3
Airbag Control Module . . . . . . . . . . . . . . . 8W-15-11 Left Front Turn Signal Lamp . . . . . . . . . . . 8W-15-3
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8 Left Headlamp . . . . . . . . . . . . . . . . . . . . . . 8W-15-3
Brake Lamp Switch . . . . . . . . . . . . . . . 8W-15-9, 10 Left Headlamp Leveling Motor . . . . . . . . . . 8W-15-3
Center High Mounted Stop Lamp . . . . . . . 8W-15-11 Left License Lamp . . . . . . . . . . . . . . . . . . . 8W-15-11
Cigar Lighter/Accessory Relay . . . . . . . 8W-15-9, 10 Left Repeater Lamp . . . . . . . . . . . . . . . . . . 8W-15-3
Cigar Lighter/Power Outlet . . . . . . . . . . . 8W-15-7, 8 Low Note Horn . . . . . . . . . . . . . . . . . . . . . . 8W-15-3
Combination Flasher . . . . . . . . . . . . . . . 8W-15-9, 10 Oxygen Sensor 1/1 Upstream . . . . . . . . . . . 8W-15-6
Controller Anti-Lock Brake . . . . . . . . . . . . . 8W-15-2 Oxygen Sensor 1/2 Downstream . . . . . . . . . 8W-15-6
Data Link Connector . . . . . . . . . . . . . . . . . 8W-15-6 Passenger Airbag On/Off Switch . . . . . . . . 8W-15-11
Daytime Running Lamp Module . . . . . . . . . 8W-15-2 Passenger Door Ajar Switch . . . . . . . . . 8W-15-9, 10
Driver Door Ajar Switch . . . . . . . . . . . . 8W-15-9, 10 Power Steering Pressure Switch . . . . . . . . . 8W-15-6
Engine Starter Motor Relay . . . . . . . . . . . . 8W-15-6 Powertrain Control Module . . . . . . . . . . . . . 8W-15-6
Fog Lamp Relay No. 1 . . . . . . . . . . . . . . . . 8W-15-9 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . 8W-15-9, 10
Fog Lamp Relay No. 2 . . . . . . . . . . . . . . . . 8W-15-9 Rear Fog Lamp . . . . . . . . . . . . . . . . . . . . . 8W-15-11
Front Fog Lamp Switch . . . . . . . . . . . . . . . 8W-15-7 Rear Fog Lamp Relay . . . . . . . . . . . . . . 8W-15-9, 10
Fuel Pump Module . . . . . . . . . . . . . . . . . . . 8W-15-6 Rear Fog Lamp Switch . . . . . . . . . . . . . . 8W-15-7, 8
Fuse 4 (FB) . . . . . . . . . . . . . . . . . . . . . . 8W-15-9, 10 Rear Washer Pump . . . . . . . . . . . . . . . . . . 8W-15-11
Fuse Block . . . . . . . . . . . . . . . . . . . . . . 8W-15-9, 10 Rear Window Defogger . . . . . . . . . . . . . . . 8W-15-11
G100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-2 Rear Window Defogger Switch . . . . . . . . 8W-15-7, 8
G101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-2 Rear Wiper Motor . . . . . . . . . . . . . . . . . . . 8W-15-11
G102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-3 Rear Wiper/Washer Switch . . . . . . . . . . . 8W-15-7, 8
G103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-4, 5 Right City Lamp . . . . . . . . . . . . . . . . . . . . . 8W-15-5
G104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-4, 5 Right Fog Lamp . . . . . . . . . . . . . . . . . . . . . 8W-15-4
G105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-6 Right Front Park/Turn Signal Lamp . . . . . . 8W-15-4
G106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8 Right Front Turn Signal Lamp . . . . . . . . . 8W-15-5
G107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8 Right Headlamp . . . . . . . . . . . . . . . . . . . 8W-15-4, 5
G200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8 Right Headlamp Leveling Motor . . . . . . . . . 8W-15-5
G201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8 Right License Lamp . . . . . . . . . . . . . . . . . 8W-15-11
G202 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8 Right Repeater Lamp . . . . . . . . . . . . . . . . . 8W-15-5
G203 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8 Seat Belt Switch . . . . . . . . . . . . . . . . . . . . 8W-15-11
G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-9, 10 Sentry Key Immobilizer Module . . . 8W-15-6, 10, 11
G301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-11 Transfer Case Switch . . . . . . . . . . . . . . . . . 8W-15-6
G302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-11 Underhood Lamp . . . . . . . . . . . . . . . . . . . . 8W-15-2
Generator . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-4, 5 Vehicle Speed Control Servo . . . . . . . . . . . . 8W-15-2
Headlamp Leveling Switch . . . . . . . . . . . 8W-15-7, 8 Windshield Washer Pump . . . . . . . . . . . . . . 8W-15-3
Headlamp Switch . . . . . . . . . . . . . . . . . . 8W-15-7, 8 Windshield Wiper Motor . . . . . . . . . . . . 8W-15-9, 10
High Note Horn . . . . . . . . . . . . . . . . . . . . . 8W-15-3 Windshield Wiper Switch . . . . . . . . . . . 8W-15-9, 10
HVAC Unit . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8
8W - 15 - 2 8W-15 GROUND DISTRIBUTION TJ
VEHICLE
SPEED
CONTROL
SERVO DAYTIME UNDERHOOD
4 (8W-30-16) RUNNING LAMP
LAMP (8W-44-3)
ABS MODULE
PUMP 8 (8W-50-8) 1
MOTOR
(8W-35-2)
2
ABS
PUMP
MOTOR
RELAY Z1 Z1
C3 (IN PDC) 18 18
Z1 (8W-35-2) BK BK
12
BK ABS
SYSTEM
Z1 Z1 RELAY
18 14 (IN PDC)
BK BK
C12 (8W-35-2)
Z1
14 OTHER BASE
BK
S106
Z1 Z1
12 18
BK BK
CONTROLLER
ANTI-LOCK
BRAKE
(8W-35-3)
13 C2 14 C2 G100
Z22 Z22
16 16
BK/PK BK/PK
S109
Z22
14
BK/PK
G101
J998W-5 TJI01502
TJ 8W-15 GROUND DISTRIBUTION 8W - 15 - 3
LEFT LEFT LEFT LEFT

REPEATER FOG FRONT FRONT
LAMP LAMP PARK/ TURN
(BUILT- (8W-50-7) TURN SIGNAL
2 UP-EXPORT) 1 3 SIGNAL 3 LAMP
(8W-52-3) LAMP (8W-52-3)
(8W-50-4) LEFT
(8W-52-3) FRONT
Z1 Z1 PARK/
18 18 FRONT FOG BUILT-UP- TURN
BK BK LAMPS EXPORT SIGNAL
3
Z1
18
LAMP
BK (EXCEPT
BUILT-UP-EXPORT
S122 EXCEPT
FRONT FOG LAMPS)
(8W-50-4)
(8W-52-3)
LOW
NOTE
HORN LEFT
(EXCEPT HEADLAMP
BUILT- (8W-50-2)
2
UP-EXPORT)
(8W-41-3) 3
LEFT
HEADLAMP
HIGH
LEVELING
NOTE
MOTOR
HORN
(8W-41-3) 3 (BUILT-
UP-EXPORT)
2 (8W-50-5)
LEFT
CITY WINDSHIELD
LAMP WASHER
(BUILT- PUMP
(8W-53-2)
2 UP-EXPORT) (8W-53-3)
(8W-50-4) B
Z1 Z1 Z1 Z1 Z1 Z1 Z1 Z1
18 18 18 18 18 20 20 18
BK BK BK BK BK BK BK BK
S117
Z1
16
BK
G102
TJI01503 J998W-5
EXCEPT BUILT-UP-EXPORT
RIGHT RIGHT GENERATOR

FOG FRONT (8W-20-2)
LAMP PARK/
(8W-50-7) TURN
1 3 SIGNAL
LAMP
(FRONT FOG
LAMPS)
Z1 Z1 (8W-50-4) Z0
18 18 (8W-52-3) 6
BK BK BK
S125
G104
RIGHT RIGHT
FRONT HEADLAMP
PARK/ (8W-50-2)
TURN
3 SIGNAL 3
LAMP
(EXCEPT FRONT
FOG LAMPS)
(8W-50-4)
(8W-52-3)
Z1 Z1 Z1
18 18 18
BK BK BK
G103
J998W-5 TJI01504
BUILT-UP-EXPORT
RIGHT RIGHT GENERATOR

REPEATER FRONT (8W-20-2)
LAMP TURN
(8W-52-3) SIGNAL
2 3 LAMP
(8W-52-3)
Z1 Z1 Z0
18 18 6
BK BK BK
S125
G104
RIGHT RIGHT
CITY HEADLAMP
LAMP (8W-50-2)
(8W-50-4)
2 3
RIGHT
HEADLAMP
LEVELING
MOTOR
3 (8W-50-5)
Z1 Z1 Z1 Z1
20 18 18 18
BK BK BK BK
S150
Z1
18
BK
G103
TJI01505 J998W-5
D11
ENGINE
STARTER
MOTOR
SENTRY
RELAY
KEY
D13 (IN PDC)
IMMOBILIZER (8W-21-2)
MODULE
(8W-30-14) 5 C104 POWERTRAIN
4
T41 CONTROL
20 T41 MODULE
BR/LB
DATA LINK
20 (8W-30-12)
Z12 CONNECTOR BR/LB A6 C1
20 (8W-30-13) T41
BK/LB 18
3 C154 4 5
BR/LB
MANUAL Z12 Z12
Z1 20 20 S134
20 TRANSMISSION BK/LB BK/TN
BK JUMPER
NOT
USED A6 C202 C4 C204 POWERTRAIN
1 C154 1 C154 CONTROL
Z12 Z12 MODULE
Z1 Z1 20 20 (8W-30-2)
20 20 BK/LB BK/TN
BK BK A31 C1 A32 C1
E6 E9 C107
A/T M/T
Z12 Z12
11 10 C103 14 14
BK/TN BK/TN
Z12 Z12
TRANSFER 20 20
CASE BK/LB BK/TN
SWITCH
(8W-31-2) S130
B
OXYGEN POWER
SENSOR STEERING
1/2 PRESSURE
DOWNSTREAM SWITCH
2 (8W-30-9) 1 (2.5L)
(8W-30-12)
LHD RHD
OXYGEN FUEL
SENSOR PUMP
Z1 Z1
1/1 20 18 MODULE
UPSTREAM BK BK (8W-30-3)
2 (8W-30-9) 6
Z1 Z1 Z1 Z1 Z1
20 20 18 18 18
BK BK BK BK BK
S132
Z1
20
BK
2 Z1 Z12
A/C 14 10
COMPRESSOR BK BK/TN
CLUTCH
(8W-42-4) G105
J998W-5 TJI01506
LHD
REAR
A/C- WIPER/ HEADLAMP REAR
HEATER WASHER LEVELING WINDOW
CONTROL SWITCH SWITCH DEFOGGER
(8W-42-2)
(HARD TOP) (BUILT-UP SWITCH
(8W-42-3) 1
C C3 5 C2 (8W-53-4) 4 -EXPORT) 1 (HARD
(8W-50-5) TOP)
(8W-48-2)
REAR CIGAR FRONT

FOG LIGHTER/ FOG
LAMP POWER LAMP
SWITCH OUTLET SWITCH
1 (BUILT-UP 3 (8W-41-2) 4 (EXCEPT
-EXPORT) BUILT-UP-
Z1 Z1 Z1 Z1 Z1 Z1 Z1 Z1
12 20 20
(8W-51-7)
18 16 20 20
EXPORT) 20
(8W-51-8) (8W-50-7)
BK BK BK BK/WT BK BK BK BK
G202 S207
BATTERY
(8W-20-2)
HEADLAMP HVAC
SWITCH UNIT
(8W-50-3) (8W-42-2)
(8W-42-3)
10
Z1 Z1 Z1
Z0 Z0 16 20 16
6 6 BK BK BK
BK BK
G200
G106 G107
INSTRUMENT
CLUSTER
(8W-40-2)
HVAC
9 C1 6 C2 UNIT
(8W-42-2)
(8W-42-3)
A/C- 1
Z2 Z2
18 18
HEATER
BK/LG BK/LG CONTROL
(8W-42-2)
(8W-42-3)
1 C2
Z11 Z11
20 20
BK/WT BK/WT
G201
G203
TJI01507 J998W-5
RHD
REAR
A/C- WIPER/ HEADLAMP REAR
HEATER WASHER SWITCH WINDOW
CONTROL SWITCH (8W-50-3) DEFOGGER
(8W-42-2)
(HARD TOP) SWITCH
(8W-42-3) 1
C C3 5 C2 (8W-53-4) 1 (HARD
TOP)
REAR CIGAR (8W-48-2)
FOG LIGHTER/
LAMP POWER
SWITCH OUTLET
1 (8W-51-7) 3 (8W-41-2)
(8W-51-8)
Z1 Z1 Z1 Z1 Z1 Z1 Z1
12 20 20 18 16 16 20
BK BK BK BK/WT BK BK BK
G202 S207
BATTERY
(8W-20-2)
HVAC HEADLAMP
UNIT LEVELING
(8W-42-2) SWITCH
(8W-42-3) (BUILT-UP
10 4 -EXPORT)
(8W-50-5)
Z1 Z1 Z1
Z0 Z0 20 20 16
6 4 BK BK BK
BK BK
G200
G106 G107
INSTRUMENT
CLUSTER
(8W-40-2) HVAC
UNIT
9 C1 6 C2 (8W-42-2)
(8W-42-3)
A/C- 1
HEATER
CONTROL
Z2 Z2
18 18 (8W-42-2)
BK/LG BK/LG (8W-42-3)
3 C2
Z11
20
BK/WT Z11
20
BK/WT
G201
G203
J998W-5 TJI01508
LHD
FOG DRIVER PASSENGER
LAMP DOOR DOOR
RELAY AJAR AJAR
NO. 1 SWITCH SWITCH
2 (EXCEPT BUILT- 1 (8W-44-4) 1 (8W-44-4)
UP-EXPORT)
(8W-50-7)
M23 M23
FOG 20 20 REAR
Z1 LAMP YL/BK YL/BK FOG
20 RELAY
BK LAMP
NO. 2 RELAY
2 (EXCEPT BUILT 4 (BUILT-UP
3
-UP-EXPORT) FUSE -EXPORT)
(8W-50-6) BLOCK (8W-51-7)
FUSE (8W-11-2)
Z1 4 Z1
20 10A 20
BK (8W-11-5) BK
24
WINDSHIELD IGNITION COMBINATION

WIPER SWITCH FLASHER
SWITCH (8W-10-9) (8W-52-2)
(8W-53-3)
1 1 4
WINDSHIELD PRNDL
WIPER LAMP
MOTOR (8W-44-5)
(8W-53-2)
(8W-53-3)
4 2
Z1 Z1 Z1 Z1 Z1 Z1
20 18 20 16 20 20
BK BK BK BK BK BK
S304
BRAKE
LAMP
SWITCH
(8W-51-6)
2
CIGAR
LIGHTER/
Z1
20 ACCESSORY
BK RELAY
5 (8W-41-2)
Z1 Z1
20 16
BK BK
G300
TJI01509 J998W-5
RHD
WINDSHIELD PASSENGER DRIVER
WIPER DOOR DOOR
SWITCH AJAR AJAR
(8W-53-3) SWITCH SWITCH
1 1 (8W-44-4) 1 (8W-44-4)
WINDSHIELD REAR
M23 M23
WIPER FOG 20 20
MOTOR LAMP YL/BK YL/BK
(8W-53-2) RELAY
(8W-53-3) (8W-51-8)
4 3
4
IGNITION FUSE
SWITCH BLOCK
(8W-10-9) Z1 (8W-11-2)
20 FUSE
BK 4
1 10A
(8W-11-5)
24
PRNDL COMBINATION
LAMP FLASHER
(8W-44-5) (8W-52-2)
2 4
Z1 Z1 Z1 Z1 Z1 Z1
20 18 16 20 20 20
BK BK BK BK BK BK
S304
Z1
20
Z1 BK
20
BK
2
SENTRY
KEY
5
IMMOBILIZER
CIGAR Z1
MODULE
(8W-30-14) Z1
LIGHTER/ 20 16
BK
ACCESSORY BK
RELAY
(8W-41-2)
G300
2
BRAKE
LAMP
SWITCH
(8W-51-6)
J998W-5 TJI01510
REAR REAR
WIPER WINDOW
MOTOR DEFOGGER
(8W-53-4) (8W-48-2)
2
Z1
12
BK
Z1
16 Z1
BK 12
BK
S400
(HARD TOP)
REAR LEFT RIGHT

FOG LICENSE LICENSE
LAMP LAMP LAMP
(8W-51-7) (8W-51-7) (8W-51-7)
(8W-51-8) (8W-51-8) (8W-51-8) Z1
2 2 2 12
BK
Z1 Z1 Z1
20 20 20
BK BK BK
6 C331
S316
(BUILT-UP
-EXPORT) Z1
Z1 12
CENTER SEAT 20 BK
REAR HIGH BELT BK
WASHER MOUNTED SWITCH
PUMP STOP (EXCEPT LHD
(HARD TOP) LAMP BUILT-UP 3 C329 6 C326
2
(8W-53-4)
B (8W-51-4) -EXPORT)
(8W-40-4)
Z1 Z1 Z1 Z1 Z1
18 18 20 20 12
BK BK BK BK BK
S309
PASSENGER AIRBAG SENTRY LHD RHD

AIRBAG CONTROL KEY
ON/OFF MODULE IMMOBILIZER
Z1 Z1
SWITCH (8W-43-2) MODULE 12 12
(8W-43-2) (LHD) BK BK
10 2
(8W-30-14)
2 C1
G5 C322 5 C322
Z6 Z6 Z1
20 18 20
BK/PK BK/PK BK
G301 G302
TJI01511 J998W-5
TJ 8W - 20 CHARGING SYSTEM 8W - 20 - 1
8W-20 CHARGING SYSTEM

Automatic Shut Down Relay . . . . . . . . . . . . 8W-20-2 G104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2 G106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2
Engine Starter Motor . . . . . . . . . . . . . . . . . 8W-20-2 G107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2
Fuse 6 (PDC) . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2 Generator . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2
Fuse 12 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2 Power Distribution Center . . . . . . . . . . . . . 8W-20-2
Fuse Block . . . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2 Powertrain Control Module . . . . . . . . . . . . . 8W-20-2
Fusible Link . . . . . . . . . . . . . . . . . . . . . . . . 8W-20-2 Sentry Key Immobilizer Module . . . . . . . . . 8W-20-2
8W - 20 - 2 8W-20 CHARGING SYSTEM TJ
ST-RUN A21 (8W-10-9) FUSIBLE

FUSE LINK
POWER A11
BLOCK 10
(8W-11-2) 12 DISTRIBUTION
FUSE DG
FUSE CENTER
12 (8W-10-2)
10A 6
(8W-11-8) 30A
(8W-10-11) A0
5 6
32 RD
F15 F15
20 20
DB DB A0 BATTERY
6
TO A14 RD
S136
F4 C106
SENTRY 14
KEY RD/WT
F15
20 IMMOBILIZER A11
DB MODULE 6
BK/GY
(8W-30-14)
B (+) ENGINE
S131 STARTER
(8W-11-8) MOTOR
F15 (8W-21-2) LHD RHD
20 Z0
DB 6
Z0 Z0
BK
B3 B1 6 4
AUTOMATIC BK BK
F15
20 SHUT
DB DOWN
RELAY
B5 B2 (IN PDC) G106 G107
(8W-30-2) (8W-15-7) (8W-15-7)
(8W-15-8) (8W-15-8)
LHD RHD 1
GENERATOR
A142 K72
14 18
13 C104 7 C104 DG/PK DG/OR
2 C103
S101
(8W-10-11)
F15 K51 A142 K72 K20 Z0

18 18 14 18 18 6
DB DB/YL DG/PK DG/OR DG BK
A2 C1 C3 C3 C12 C3 C25 C3 B10 C2

FUSED AUTOMATIC AUTOMATIC VOLTAGE GENERATOR POWERTRAIN
IGNITION SHUT SHUT REGULATOR FIELD CONTROL
SWITCH DOWN DOWN SIGNAL DRIVER MODULE
OUTPUT RELAY RELAY (+)
(8W-30-2)
(ST-RUN) CONTROL OUTPUT (8W-30-12) G104
SENSE
(8W-15-4)
(8W-15-5)
J998W-5 TJI02002
TJ 8W - 21 STARTING SYSTEM 8W - 21 - 1
8W-21 STARTING SYSTEM

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-21-2 Fuse Block . . . . . . . . . . . . . . . . . . . . . . . . . 8W-21-2
Clutch Pedal Position Switch . . . . . . . . . . . 8W-21-2 G105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-21-2
Clutch Pedal Position Switch Connector . . . 8W-21-2 Ignition Switch . . . . . . . . . . . . . . . . . . . . . . 8W-21-2
Engine Starter Motor . . . . . . . . . . . . . . . . . 8W-21-2 Manual Transmission Jumper . . . . . . . . . . 8W-21-2
Engine Starter Motor Relay . . . . . . . . . . . . 8W-21-2 Park/Neutral Position Switch . . . . . . . . . . . 8W-21-2
Fuse 2 (PDC) . . . . . . . . . . . . . . . . . . . . . . . 8W-21-2 Power Distribution Center . . . . . . . . . . . . . 8W-21-2
Fuse 20 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-21-2
8W - 21 - 2 8W-21 STARTING SYSTEM TJ
BATT A1 (8W-10-8)
POWER
IGNITION 8 DISTRIBUTION
SWITCH FUSE CENTER
1 START 2 (8W-10-2)
2 RUN
1 4 40A
0 OFF
2 3 (8W-10-8)
0 3 LOCK 1
4 ACC
10 (8W-10-9)
A2 A0
12 6
S331 PK/BK RD
A41 A2
F6 C106
A/T M/T
14 12
A2
YL PK/BK
2 12
20 CLUTCH CLUTCH PK/BK
FUSE 2 PEDAL
BLOCK NOT
PEDAL
POSITION POSITION
(8W-11-2) USED TO
FUSE SWITCH SWITCH
20 1
CONNECTOR IGNITION
20A 1 SWITCH
(A/T) (8W-10-9)
(8W-11-9)
40
T141 14YL/RD BATTERY
(8W-20-2)
F9 C106
T141
14
YL/RD
D11 D10
ENGINE
STARTER
MOTOR
RELAY
D13 D14 (IN PDC)
T41
20 T40
BR/LB 12
BR
5 C104
LHD RHD
S134
(8W-15-6)
A/T (8W-70-4) M/T 12 C104 6 C104
3 C154 3 C154
Z1 MANUAL A0
T41 20 TRANSMISSION T40 6
20 BK JUMPER 12 RD
BR/LB BR
1 C154
Z1 ENGINE
20
BK STARTER
2 2 1 MOTOR
PARK/ S132 1 PULL-IN
P/N (8W-15-6) 2 HOLD-IN
NEUTRAL
Z1 M
POSITION 14
SWITCH BK
G105
(8W-15-6)
J998W-5 TJI02102
TJ 8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 1
8W-30 FUEL/IGNITION SYSTEMS

A/C Compressor Clutch Relay . . . . . . . . . . . 8W-30-3 Fuse Block . . . . . . . . . . . . . . . . . . 8W-30-2, 3, 11, 14
A/C Heater Control . . . . . . . . . . . . . . . . . . 8W-30-12 G100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-16
A/C High Pressure Switch . . . . . . . . . . . . . 8W-30-12 G105 . . . . . . . . . . . . . . . . . 8W-30-2, 3, 9, 12, 13, 14
A/C Low Pressure Switch . . . . . . . . . . . . . 8W-30-12 G300 . . . . . . . . . . . . . . . . . . . . . . . 8W-30-12, 14, 16
Airbag Control Module . . . . . . . . . . . . . . . 8W-30-14 G302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-14
Automatic Shut Down Relay . . . . 8W-30-2, 4, 5, 6, 9 Generator . . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-12
Battery Temperature Sensor . . . . . . . . 8W-30-10, 15 Headlamp Switch . . . . . . . . . . . . . . . . . . . 8W-30-14
Brake Lamp Switch . . . . . . . . . . . . . . . 8W-30-12, 16 Horn Relay . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-15
Brake Shift Interlock Solenoid . . . . . . 8W-30-12, 16 Horn Switch . . . . . . . . . . . . . . . . . . . . . . . 8W-30-15
Camshaft Position Sensor . . . . . . . . . . . . . . 8W-30-4 Idle Air Control Motor . . . . . . . . . . . . . . . . 8W-30-11
Cigar Lighter/Accessory Relay . . . . . . . 8W-30-12, 16 Ignition Coil . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-4
Clockspring . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-15 Instrument Cluster . . . . . . . . . . . . . . . . . . 8W-30-14
Controller Anti-Lock Brake . . . . . . . . . . . . 8W-30-13 Intake Air Temperature Sensor . . . . . . . . 8W-30-7, 8
Crankshaft Position Sensor . . . . . . . . . . . . 8W-30-4 Leak Detection Pump . . . . . . . . . . . . . . 8W-30-9, 11
Data Link Connector . . . . . . . . . . . . . . 8W-30-13, 14 Left Speed Control Switch Pod . . . . . . . . . 8W-30-15
Daytime Running Lamp Module . . . . . . . . 8W-30-10 Manifold Absolute Pressure Sensor . . . . . 8W-30-7, 8
Duty Cycle Evap/Purge Solenoid . . . . . . . . 8W-30-11 Manual Transmission Jumper . . . . . . . . . . 8W-30-12
Engine Coolant Temperature Sensor . . . . 8W-30-7, 8 Oxygen Sensor 1/1 Upstream . . . . . . . . . . . 8W-30-9
Engine Oil Pressure Sensor . . . . . . . . 8W-30-7, 8, 10 Oxygen Sensor 1/2 Downstream . . . . . . . . . 8W-30-9
Fuel Injector No. 1 . . . . . . . . . . . . . . . . . 8W-30-5, 6 Park/Neutral Position Switch . . . . . . . . . . 8W-30-12
Fuel Injector No. 2 . . . . . . . . . . . . . . . . . 8W-30-5, 6 Power Distribution Center . . . 8W-30-2, 3, 4, 5, 6, 9,
Fuel Injector No. 3 . . . . . . . . . . . . . . . . . 8W-30-5, 6 11, 13, 15
Fuel Injector No. 4 . . . . . . . . . . . . . . . . . 8W-30-5, 6 Power Steering Pressure Switch . . . . . . . . 8W-30-12
Fuel Injector No. 5 . . . . . . . . . . . . . . . . . . . 8W-30-6 Powertrain Control Module . . 8W-30-2, 3, 4, 5, 6, 7,
Fuel Injector No. 6 . . . . . . . . . . . . . . . . . . . 8W-30-6 8, 9, 10, 11, 12, 13, 14, 15, 16
Fuel Pump Module . . . . . . . . . . . . . . . . . . . 8W-30-3 Right Speed Control Switch Pod . . . . . . . . 8W-30-15
Fuel Pump Relay . . . . . . . . . . . . . . . . . . . . 8W-30-3 Sentry Key Immobilizer Module . . . . . . . 8W-30-2, 3,
Fuse 1 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-14 13, 14
Fuse 6 (PDC) . . . . . . . . . . . . . . . . . . . . . . . 8W-30-2 Sound Bar Dome Lamp . . . . . . . . . . . . . . . 8W-30-13
Fuse 11 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-30-11 Throttle Position Sensor . . . . . . . . . . . . . . 8W-30-10
Fuse 12 (FB) . . . . . . . . . . . . . . . . . . . 8W-30-2, 3, 14 Torque Converter Clutch Solenoid . . . . . . . 8W-30-11
Fuse 18 (PDC) . . . . . . . . . . . . . . . . . . . 8W-30-4, 5, 6 Underhood Lamp . . . . . . . . . . . . . . . . . . . 8W-30-13
Fuse 19 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-30-3 Vehicle Speed Control Servo . . . . . . . . . . . 8W-30-16
Fuse 20 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-30-13 Vehicle Speed Sensor . . . . . . . . . . . . . . . . 8W-30-10
Fuse 27 (PDC) . . . . . . . . . . . . . . . . . . . . 8W-30-9, 11
8W - 30 - 2 8W-30 FUEL/IGNITION SYSTEM TJ
ST-RUN A21 (8W-10-9) BATT A0 (8W-10-6)

FUSE POWER
BLOCK 12 DISTRIBUTION
FUSE
(8W-11-2)
FUSE CENTER
12 6 (8W-10-2)
10A 30A
(8W-11-8) (8W-10-11)
5
32
F15
20 F15
DB 20
DB
F4 C106
3
SENTRY A14 A14
FUSED 14 14
F15 IGNITION KEY RD/WT RD/WT
20 SWITCH IMMOBILIZER
DB OUTPUT
(ST-RUN)
MODULE
(8W-30-14)
S131
(8W-11-8)
F15
F15 20
20 DB
DB 3 C103
B3 B1
LHD RHD AUTOMATIC
SHUT
DOWN
13 C104 7 C104
RELAY
B5 B2 (IN PDC) A14
14
S101 RD/WT
(8W-10-11)
F15 K51 A142
18 18 14
DB DB/YL DG/PK
A2 C1 C3 C3 C12 C3 A22 C1
FUSED AUTOMATIC AUTOMATIC FUSED POWERTRAIN
IGNITION SHUT SHUT B(+) CONTROL
SWITCH DOWN DOWN MODULE
OUTPUT RELAY RELAY
(ST-RUN) CONTROL OUTPUT
GROUND SENSE GROUND
A31 C1 A32 C1
Z12 Z12
14 14
BK/TN BK/TN
S130
(8W-15-6)
Z12
10
BK/TN
G105
(8W-15-6)
J998W-5 TJI03002
TJ 8W-30 FUEL/IGNITION SYSTEM 8W - 30 - 3
ST-RUN A21 (8W-10-9) BATT A0 (8W-10-6)

FUSE POWER
BLOCK A18 DISTRIBUTION
FUSE
(8W-11-2)
FUSE CENTER
12 19 (8W-10-2)
10A 20A
(8W-11-8) (8W-10-14)
A17
32
F15
20 F15
DB 20
DB
F4 C106
3
S131 FUSED SENTRY
(8W-11-8) IGNITION KEY
F15 SWITCH IMMOBILIZER A61
20 OUTPUT 18
(ST-RUN)
MODULE
DB DG/BK
(8W-30-14)
B18 B16
FUEL
PUMP
RELAY
(IN PDC)
B20 B17
A141
18
DG/WT
6 7
C103
K226 A141
20 18
DB/LG DG/WT
B8 3 1
A/C FUEL
COMPRESSOR PUMP
CLUTCH M MODULE
RELAY
B10 (IN PDC) 4 6
(8W-42-4)
K167
20
BR/YL
S133 Z1
(8W-70-3) 18
C13 K31 K226 K167 BK
18 18 18 18
DB/OR BR DB/LG BR/YL
S132
C1 C3 C19 C3 C26 C3 A4 C1 (8W-15-6)
A/C FUEL FUEL SENSOR POWERTRAIN Z1
COMPRESSOR PUMP LEVEL GROUND CONTROL 14
CLUTCH RELAY SENSOR MODULE BK
RELAY CONTROL SIGNAL
CONTROL
G105
(8W-15-6)
TJI03003 J998W-5
BATT A14 (8W-10-11)

POWER
B1
A20 AUTOMATIC
DISTRIBUTION
FUSE SHUT CENTER
18 DOWN (8W-10-2)
20A RELAY
(8W-10-11) (8W-30-2)
A19
B2
F42 A142 A142

18 14 14
DG/LG DG/PK DG/PK
S129
(8W-70-4)
S101
LHD RHD (8W-10-11) K7
20
OR
11 C104 4 C104
3
5V CRANKSHAFT
SUPPLY POSITION
SENSOR
S126
(8W-10-12) CRANKSHAFT
POSITION
F42 SENSOR SENSOR
18 SIGNAL GROUND
DG/LG
1 2
K167 K7
2.5L 4.0L 20 20
BR/YL OR
F42 F42 S127

18 18 (8W-70-3) 3
DG/LG DG/LG
5V CAMSHAFT
S128 SUPPLY POSITION
(8W-10-12) SENSOR
F42 CAMSHAFT
18 POSITION
DG/LG SENSOR SENSOR
GROUND SIGNAL
1
1
IGNITION 2
COIL K167 K167
20 20
BR/YL BR/YL
2 S133
(8W-70-3)
K19
18 K7 K24 K167 K44
GY 18 18 18 18
OR GY/BK BR/YL TN/YL
A7 C1 A17 C1 A8 C1 A4 C1 A18 C1
IGNITION 5V CRANKSHAFT SENSOR CAMSHAFT POWERTRAIN
COIL SUPPLY POSITION GROUND POSITION CONTROL
NO. 1 SENSOR SENSOR MODULE
DRIVER SIGNAL SIGNAL
J998W-5 TJI03004
2.5L
BATT A14 (8W-10-11)
POWER
B1 DISTRIBUTION
AUTOMATIC A20 CENTER
SHUT FUSE (8W-10-2)
DOWN 18
RELAY 20A
(8W-30-2) (8W-10-11)
A19
B2
A142 A142 F42

14 14 18
DG/PK DG/PK DG/LG
S101 LHD RHD

(8W-10-11)
11 C104 4 C104
F42
18
DG/LG
S126
(8W-10-12)
F42
18
DG/LG
S128
(8W-10-12)
F42 F42 F42 F42

18 18 18 18
DG/LG DG/LG DG/LG DG/LG
1 1 1 1
FUEL FUEL FUEL FUEL
INJECTOR INJECTOR INJECTOR INJECTOR
NO. 1 NO. 2 NO. 3 NO. 4
2 2 2 2
K11 K12 K13 K14

18 18 18 18
WT/DB TN YL/WT LB/BR
B4 C2 B15 C2 B5 C2 B16 C2
FUEL FUEL FUEL FUEL POWERTRAIN
INJECTOR INJECTOR INJECTOR INJECTOR CONTROL
NO. 1 NO. 2 NO. 3 NO. 4 MODULE
DRIVER DRIVER DRIVER DRIVER
TJI03005 J998W-5
4.0L
BATT A14 (8W-10-11)
POWER
B1
AUTOMATIC A19 DISTRIBUTION
SHUT FUSE CENTER
DOWN 18 (8W-10-2)
RELAY 20A
(8W-30-2) (8W-10-11)
A20
B2
F42
A142 A142 18
14 14 DG/LG
DG/PK DG/PK
LHD RHD
S101
(8W-10-11) 11 C104 4 C104
F42
18
DG/LG
S126
(8W-10-12)
F42
18 F42 F42 F42
DG/LG 18 18 18
DG/LG DG/LG DG/LG F42
S128 18
(8W-10-12) DG/LG
F42 F42
18 18
DG/LG DG/LG
1 1 1
FUEL FUEL FUEL
INJECTOR INJECTOR INJECTOR
NO. 2 NO. 4 NO. 6
2 2 2
1 1 1
FUEL FUEL FUEL
INJECTOR INJECTOR INJECTOR
NO. 1 NO. 3 NO. 5
2 2 2
K11 K12 K13 K14 K15 K16

18 18 18 18 18 18
WT/DB TN YL/WT LB/BR PK/BK LG/BK
B4 C2 B15 C2 B5 C2 B16 C2 B6 C2 B12 C2

FUEL FUEL FUEL FUEL FUEL FUEL POWERTRAIN
INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR CONTROL
NO. 1 NO. 2 NO. 3 NO. 4 NO. 5 NO. 6 MODULE
DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER
J998W-5 TJI03006
2.5L
S129
(8W-70-4)
K7
20
OR
3
MANIFOLD
ABSOLUTE
PRESSURE
SENSOR
2 1
K167
20
BR/YL
S127
(8W-70-3)
K167 K167 K167

20 20 20
BR/YL BR/YL BR/YL
K167
20
BR/YL 2
ENGINE
3
COOLANT
ENGINE
TEMPERATURE
OIL
SENSOR
PRESSURE
SENSOR 1
2 1 2
INTAKE
K6 AIR
20 TEMPERATURE
VT/OR SENSOR
1
S123 S133
(8W-70-4) (8W-70-3)
K6 K167
18 18
K7 K1 G60 VT/OR BR/YL K2 K21
18 18 18 18 18
OR DG/RD GY/YL TN/BK BK/RD
A17 C1 A27 C1 B23 C2 B31 C2 A4 C1 A16 C1 A15 C1

5V MANIFOLD ENGINE 5V SENSOR ENGINE INTAKE POWERTRAIN
SUPPLY ABSOLUTE OIL SUPPLY GROUND COOLANT AIR CONTROL
PRESSURE PRESSURE TEMPERATURE TEMPERATURE MODULE
SENSOR SENSOR SENSOR SENSOR
SIGNAL SIGNAL SIGNAL SIGNAL
TJI03007 J998W-5
4.0L
S129
(8W-70-4)
K7
20
OR
3
MANIFOLD
ABSOLUTE
PRESSURE
SENSOR
2 1
K167
20
BR/YL
S127
(8W-70-3)
K167 K167 K167

20 20 20
BR/YL BR/YL BR/YL
S133
(8W-70-3)
K167
20
BR/YL 2
ENGINE
COOLANT
TEMPERATURE
SENSOR
1
3 2
ENGINE INTAKE
OIL AIR
PRESSURE TEMPERATURE
SENSOR SENSOR
2 1 1
K6
20
VT/OR
S123
(8W-70-4)
K7 K1 G60 K6 K167 K2 K21
18 18 18 18 18 18 18
OR DG/RD GY/YL VT/OR BR/YL TN/BK BK/RD
A17 C1 A27 C1 B23 C2 B31 C2 A4 C1 A16 C1 A15 C1

5V MANIFOLD ENGINE 5V SENSOR ENGINE INTAKE POWERTRAIN
SUPPLY ABSOLUTE OIL SUPPLY GROUND COOLANT AIR CONTROL
PRESSURE PRESSURE TEMPERATURE TEMPERATURE MODULE
SENSOR SENSOR SENSOR SENSOR
SIGNAL SIGNAL SIGNAL SIGNAL
J998W-5 TJI03008
BATT A14 (8W-10-11)
B1 POWER
A1 AUTOMATIC DISTRIBUTION
FUSE
SHUT CENTER
DOWN (8W-10-2)
27
RELAY
10A (8W-30-2)
(8W-10-11)
A2 B2
F142 A142 A142

20 14 14
OR/DG DG/PK DG/PK
LEAK
OTHER DETECTION S101
(8W-10-11)
S107
(8W-10-11)
F142
20
F142 OR/DG
20
OR/DG 3 C180
1 C103 2
S124 FUSED LEAK
(8W-10-11) AUTOMATIC DETECTION
F142 SHUT DOWN PUMP
18 RELAY
OUTPUT
(EXCEPT BUILT-
OR/DG
F142 F142 UP-EXPORT)
18 18 (8W-30-11)
OR/DG OR/DG
4 1 1 4
OXYGEN OXYGEN
SENSOR SENSOR
1/1 1/2
UPSTREAM DOWNSTREAM
3 2 2 3
K167 Z1 Z1 K167
20 18 18 20
BR/YL BK BK BR/YL
S127 S132
(8W-70-3) (8W-15-6)
Z1
K167 14
20 BK
BR/YL
G105
(8W-15-6)
S133
(8W-70-3)
K41 K167 K141
18 18 18
BK/DG BR/YL TN/WT
A24 C1 A4 C1 A25 C1
OXYGEN SENSOR OXYGEN POWERTRAIN
SENSOR GROUND SENSOR CONTROL
1/1 1/2 MODULE
SIGNAL SIGNAL
TJI03009 J998W-5
VEHICLE
SPEED
VEHICLE SENSOR
SPEED
K7 SENSOR
SENSOR 5V
20 SIGNAL
S129 OR
GROUND SUPPLY
(8W-70-4) 2 1 3
3
THROTTLE K167
POSITION 20
SENSOR BR/YL
2 1
K167
20
K6 G7
BR/YL
20 20
VT/OR WT/OR
S127
(8W-70-3)
K167
20
BR/YL
S133
(8W-70-3)
8 C103 S123 S135
(8W-70-4)
K167
20
BR/YL G7
20
S147 WT/OR
(8W-70-3) K6
20
LHD RHD VT/OR
12 C103
K167 K167
20 18
BR/YL BR/YL G7
20
WT/OR
2
BATTERY 1 7
TEMPERATURE 5V ENGINE VEHICLE DAYTIME
SENSOR SUPPLY OIL SPEED RUNNING
PRESSURE SENSOR LAMP
SIGNAL
1 SENSOR MODULE
(8W-30-7) (8W-50-8)
(8W-30-8)
K7 K22 K118 K167 K6 G7
18 18 18 18 18 18
OR OR/DB PK/YL BR/YL VT/OR WT/OR
A17 C1 A23 C1 C15 C3 A4 C1 B31 C2 B27 C2

5V THROTTLE BATTERY SENSOR 5V VEHICLE POWERTRAIN
SUPPLY POSITION TEMPERATURE GROUND SUPPLY SPEED CONTROL
SENSOR SENSOR SENSOR MODULE
SIGNAL SIGNAL SIGNAL
J998W-5 TJI03010
FROM
ST-RUN A21 (8W-10-9)
S101
FUSE (8W-10-11)
BLOCK
(8W-11-2)
FUSE
11
POWER
10A A1 DISTRIBUTION
(8W-11-8) FUSE CENTER
27 (8W-10-2)
31 10A
(8W-10-11)
A2
F12
20
RD/LG
F142
20
F10 C106 OR/DG
S102
(8W-11-8) S107
(8W-10-11)
F12
20 3 C180
F12
RD/LG F142
20
RD/LG 20
9 C103 OR/DG
F12 2
11 C110 LEAK
20 FUSED
RD/LG AUTOMATIC DETECTION
SHUT DOWN PUMP
F12 A
RELAY
20 TORQUE OUTPUT (EXCEPT
RD/LG CONVERTER BUILT-UP
CLUTCH LEAK LEAK -EXPORT)
DETECTION DETECTION
SOLENOID PUMP PUMP
B SOLENOID SWITCH
2 CONTROL SENSE
DUTY 3 4
CYCLE
EVAP/ K106 K105
PURGE IDLE 20 20
AIR WT/DG WT/OR
1 SOLENOID
IDLE IDLE IDLE IDLE CONTROL
K52 AIR AIR AIR AIR MOTOR
20 CONTROL CONTROL CONTROL CONTROL
PK/BK NO. 1 NO. 2 NO. 3 NO. 4
DRIVER DRIVER DRIVER DRIVER 2 1 C180
10 C110 4 3 2 1
K52 T23 K106 K105

18 18 K39 K60 K40 K59 18 18
PK/BK OR/LG 18 18 18 18 WT/DG WT/OR
GY/RD YL/BK BR/WT VT/BK
C20 C3 B11 C2 A19 C1 A10 C1 A11 C1 A20 C1 C10 C3 C14 C3

DUTY TRANSMISSION IDLE IDLE IDLE IDLE LEAK LEAK POWERTRAIN
CYCLE/ LOW/ AIR AIR AIR AIR DETECTION DETECTION CONTROL
EVAP OVERDRIVE CONTROL CONTROL CONTROL CONTROL PUMP PUMP MODULE
PURGE SOLENOID NO. 1 NO. 2 NO. 3 NO. 4 SOLENOID SWITCH
SOLENOID DRIVER DRIVER DRIVER DRIVER CONTROL SENSE
CONTROL
TJI03011 J998W-5
C21 20 DB/OR A/C- GENERATOR

A/C
HEATER GENERATOR (8W-20-2)
2 2
SELECT CONTROL VOLTAGE FIELD
A/C A/C (8W-42-3) REGULATOR DRIVER
INPUT
LOW HIGH SIGNAL (+)
PRESSURE PRESSURE A C3 1 2
SWITCH SWITCH C90
1 1 20
LG
C22 C90
20 20 6 C170
DB/WT LG
C90 K72
2 1 C104 20 18
LG DG/OR
C90
C22 20 2 C103
18 LG
DB/WT
K72 K20
S103 18 18
(8W-42-4) DG/OR DG
C90
18
LG
C22 C3 C23 C3 C25 C3 B10 C2
A/C A/C VOLTAGE GENERATOR POWERTRAIN
SWITCH SELECT REGULATOR FIELD CONTROL
SENSE INPUT PARK/ SIGNAL DRIVER MODULE
NEUTRAL (+)
BRAKE POSITION POWER STEERING
SWITCH SWITCH PRESSURE
SENSE SENSE SWITCH SENSE
C24 C3 A6 C1 A12 C1
K29 T41 K10
18 18 18
WT/PK BR/LB DB/BR
D14 C108 S134
(8W-15-6) 2
K29 (8W-70-4) POWER
20 STEERING
WT/PK
PRESSURE
1 SWITCH
T41
BRAKE CIGAR 20 (2.5L)
1
LAMP LIGHTER/ BR/LB
SWITCH ACCESSORY A/T M/T
(8W-51-6)
GROUND RELAY
(8W-41-2) LHD RHD
2 5 3 C154
Z1 20BK 3 C154 Z1 MANUAL
LHD RHD
20 TRANSMISSION Z1 Z1
T41
BK JUMPER 20 18
20
Z1 BK BK
BR/LB
K29
20 1 C154
BK
20 Z1
WT/PK Z1 20
20 S304 BK
BK (8W-15-10)
Z1 2 S132
1 (8W-15-6)
BRAKE 16 PARK/ Z1
BRAKE BK
SWITCH SHIFT NEUTRAL 14
P/N
SENSE INTERLOCK POSITION BK
SOLENOID SWITCH
G300 (8W-21-2) G105
(8W-31-2)
(8W-15-9) (8W-15-6)
J998W-5 TJI03012
(8W-15-10)
BATT A0 (8W-10-6)
POWER
A16 DISTRIBUTION
FUSE CENTER
20 (8W-10-2)
10A
(8W-10-15)
A15
M1
20 M1
PK/WT 20
PK/WT
D12 C108 HARD SOFT
M1 TOP TOP
20
PK/WT
2 B7 C203
TO TO
FUSED UNDERHOOD DOME SOUND
B(+) LAMP LAMP BAR
(8W-44-3) S204
(8W-10-15) AND DOME
M1 SOUND LAMP
20
PK/WT
BAR (8W-44-2)
DOME
16
LAMP
(8W-44-2) DATA
LINK
6 7 4 5 CONNECTOR
D20 D21 SENTRY
20 20 KEY
LG PK Z12 Z12
IMMOBILIZER 20 20
B10 MODULE
B8 C203 GROUND BK/LB BK/TN
4 (8W-30-14)
D20 D21 A6 C202 C4 C204
20 20
Z12 20BK/LB
LG PK Z12 Z12
E13 E14 C107 20 20
BK/LB BK/TN
E6 E9 C107
Z12 Z12
20 20
BK/LB BK/TN
11 10
C103
Z12 Z12
D20 D21 20 20
18 18 D21
BK/LB BK/TN
LG PK 20
PK
C29 C3 C27 C3 S130
SCI SCI POWERTRAIN (8W-15-6)
RECEIVE TRANSMIT/ CONTROL 3 C1
ISO SCI CONTROLLER Z12
MODULE 10
9141K TRANSMIT/ ANTI-LOCK
ISO BK/TN
BRAKE
9141K (8W-35-5)
G105
(8W-15-6)
TJI03013 J998W-5
BATT A6 (8W-10-10) ST-RUN A21 (8W-10-9)

INSTRUMENT
CLUSTER FUSE
CCD CCD (8W-40-3) BLOCK
BUS BUS (8W-40-4) (8W-11-2)
(8W-40-5) FUSE FUSE
(-) (+)
(8W-40-7) 1 12
20A 10A
1 2 (8W-11-4) (8W-11-8)
C1 C1
21 32
F34
18
TN/BK
D2 D1
20 20
WT/BK VT/BR A11 C202
TWISTED DATA
F34 F15
PAIR 18 20
LINK
TN/BK DB CONNECTOR
(8W-30-13)
4 4
F34 FUSED HEADLAMP
DATA 20 B(+) SWITCH
LINK TN/BK (8W-50-2)
(8W-50-4) Z12
CONNECTOR 20
11 3 1 3 BK/LB
FUSED FUSED SENTRY
D2 D1 B(+) IGNITION KEY
20 20 SWITCH IMMOBILIZER
WT/BK VT/BR OUTPUT
(ST-RUN)
MODULE
CCD CCD
BUS BUS
B12 B11 (-) (+) GROUND GROUND
C203
5 6 2 4
Z12
D2 D1 D2 D1 20
20 TWISTED 20 20 TWISTED 20 BK/LB
WT/BK PAIR VT/BR WT/BK PAIR VT/BR
A6 C202
Z1
20
S302 BK
Z12
20
S303 BK/LB
D2 D1
20 20 E6 C107
LHD RHD
WT/BK VT/BR
11 C103
D5 D4 C108 TWISTED Z12
Z1
PAIR 20
TWISTED 20 S304 BK/LB
PAIR BK (8W-15-10)
D2 D1 Z1
18 18 16 S130
D2 D1
WT/BK VT/BR G302 BK (8W-15-6)
18 18
WT/BK VT/BR (8W-15-11) Z12
10
C28 C3 C30 C3 18 19 BK/TN
CCD CCD POWERTRAIN CCD CCD AIRBAG G300
BUS BUS CONTROL BUS BUS CONTROL (8W-15-10)
(-) (+) MODULE (-) (+) MODULE G105
(8W-43-3) (8W-15-6)
J998W-5 TJI03014
POWERTRAIN
SPEED
CONTROL
CONTROL MODULE
SWITCH SENSOR
SIGNAL GROUND
C32 C3 A4 C1
B13 POWER
BATTERY K167
DISTRIBUTION
18 HORN
TEMPERATURE RELAY CENTER
BR/YL
SENSOR SENSOR (8W-41-3) (8W-10-2)
RETURN (8W-30-10) S133
2 (8W-70-3)
K167 B15
LHD RHD 20
BR/YL
K167 K167
20 18 8 C103
BR/YL BR/YL X3
V37
18 20
RD/LG RD/YL
S147
(8W-70-3)
K167
20
BR/YL (NOT E7 C107
USED)
D3 D3
C108
SPEED OTHER X3
CONTROL 20
D10 C108 RD/YL
V37 K167
20 20
RD/LG BR/YL
2 C2 3 C2 1 C2
CLOCKSPRING
HORN
SWITCH
LEFT RIGHT
SPEED SPEED
CONTROL CONTROL
SWITCH SWITCH
1 2 POD 1 2 3 POD
1 ON/OFF 1 RESUME/ACCEL
2 SET 2 CANCEL
3 COAST
TJI03015 J998W-5
POWERTRAIN
SPEED SPEED SPEED CONTROL
CONTROL CONTROL CONTROL MODULE
VACUUM VENT ON/OFF BRAKE
SOLENOID SOLENOID SWITCH SWITCH
CONTROL CONTROL SENSE SENSE
C4 C3 C5 C3 C11 C3 C24 C3
BRAKE
V32 K29
18 18
SHIFT
BRAKE
YL/RD WT/PK SWITCH INTERLOCK
SENSE SOLENOID
V36 V35 (8W-31-2)
18 18 1
TN/RD LG/RD
K29
D1 D14
C108 20
WT/PK
V32
20 K29
YL/RD 20
WT/PK
3 1 5
BRAKE
1 2 3 LAMP
VEHICLE SWITCH
VACUUM VENT SPEED (8W-51-6)
SOLENOID SOLENOID CONTROL 4 2 6
SERVO
V30 Z1
20 20
DUMP
DB/RD BK CIGAR
SOLENOID LIGHTER/
ACCESSORY
GROUND RELAY
V30 E11 C107 (8W-41-2)
4 5
20
DB/RD
Z1
20
BK
Z1 LHD RHD
18
BK
Z1
20
BK
S106 Z1
(8W-15-2) 20 S304
BK (8W-15-10)
Z1
Z1 16
12 BK
BK
G300
G100 (8W-15-9)
(8W-15-2) (8W-15-10)
J998W-5 TJI03016
TJ 8W - 31 TRANSMISSION CONTROL SYSTEM 8W - 31 - 1
8W-31 TRANSMISSION CONTROL SYSTEM

Brake Lamp Switch . . . . . . . . . . . . . . . . . . 8W-31-2 G105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-31-2
Brake Shift Interlock Solenoid . . . . . . . . . . 8W-31-2 G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-31-2
Cigar Lighter/Accessory Relay . . . . . . . . . . 8W-31-2 Instrument Cluster . . . . . . . . . . . . . . . . . . . 8W-31-2
Fuse 10 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-31-2 Powertrain Control Module . . . . . . . . . . . . . 8W-31-2
Fuse 11 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-31-2 Torque Converter Clutch Solenoid . . . . . . . 8W-31-2
Fuse Block . . . . . . . . . . . . . . . . . . . . . . . . . 8W-31-2 Transfer Case Switch . . . . . . . . . . . . . . . . . 8W-31-2
8W - 31 - 2 8W-31 TRANSMISSION CONTROL SYSTEM TJ
ST-RUN A21 (8W-10-9)

FUSE
BLOCK
(8W-11-2)
FUSE FUSE
11 10
10A 10A
(8W-11-8) (8W-11-8)
31 30
G5 20DB/WT
F12
20
RD/LG
A10 C202
G5
20
DB/WT G5
F10 C106
20
DB/WT
F12 2
20 8 C2
RD/LG
BRAKE INSTRUMENT
SHIFT CLUSTER
INTERLOCK 4WD (8W-40-5)
SOLENOID INDICATOR
S102
1
(8W-11-8)
F12 K29 5 C1
20 20
G107
RD/LG WT/PK
20
BK/RD
9 C103
D14 C108 K29
20 5 C170
WT/PK
F12 1 13 C103
20 BRAKE
RD/LG G107
LAMP 20
SWITCH BK/RD
(8W-51-6)
A A
TORQUE 2
TRANSFER
CONVERTER Z1 CASE
CIGAR
CLUTCH 20 SWITCH
BK LIGHTER/
SOLENOID
K29 ACCESSORY
B 18 RELAY B
GROUND
WT/PK (8W-41-2)
5
T23 Z1
18 20 Z1
OR/LG BK 20
BK
LHD RHD
B11 C2 C24 C3 S304 S132

POWERTRAIN Z1 (8W-15-10)
TRANSMISSION BRAKE 20 (8W-15-6)
Z1
LOW/ SWITCH CONTROL BK 16
OVERDRIVE SENSE Z1
MODULE BK 14
SOLENOID (8W-30-11) BK
(8W-30-12)
G300 G105
(8W-15-9) (8W-15-6)
J998W-5 (8W-15-10) TJI03102
TJ 8W - 35 ANTI-LOCK BRAKES 8W - 35 - 1
8W-35 ANTI-LOCK BRAKES

ABS Diode . . . . . . . . . . . . . . . . . . . . . . . . . 8W-35-3 Fuse 21 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-35-2
ABS Pump Motor . . . . . . . . . . . . . . . . . . . . 8W-35-2 Fuse Block . . . . . . . . . . . . . . . . . . . . . 8W-35-2, 3, 5
ABS Pump Motor Relay . . . . . . . . . . . . . . . 8W-35-2 G-Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-35-5
ABS System Relay . . . . . . . . . . . . . . . . . . . 8W-35-2 G100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-35-2
ABS Warning Indicator . . . . . . . . . . . . . . . . 8W-35-3 G101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-35-3
Brake Lamp Switch . . . . . . . . . . . . . . . . . . 8W-35-5 Hydraulic Control Unit . . . . . . . . . . . . . . . . 8W-35-4
Brake Shift Interlock Solenoid . . . . . . . . . . 8W-35-3 Instrument Cluster . . . . . . . . . . . . . . . . . . . 8W-35-3
Controller Anti-Lock Brake . . . . . 8W-35-2, 3, 4, 5, 6 Left Front Wheel Speed Sensor . . . . . . . . . 8W-35-6
Data Link Connector . . . . . . . . . . . . . . . . . 8W-35-5 Left Rear Wheel Speed Sensor . . . . . . . . . . 8W-35-6
Fuse 2 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-35-5 Power Distribution Center . . . . . . . . . . . . . 8W-35-2
Fuse 7 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-35-2, 3 Powertrain Control Module . . . . . . . . . . . . . 8W-35-5
Fuse 10 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-35-3 Right Front Wheel Speed Sensor . . . . . . . . 8W-35-6
Fuse 13 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-35-2 Right Rear Wheel Speed Sensor . . . . . . . . . 8W-35-6
Fuse 14 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-35-2
8W - 35 - 2 8W-35 ANTI-LOCK BRAKES TJ
FROM
RUN A22 (8W-10-8)
S146
FUSE (8W-35-3)
BLOCK A
(8W-11-2)
FUSE
7 B48
10A 20
(8W-11-7) RD/YL
BATT A0 (8W-10-6)
27
POWER
F20 DISTRIBUTION
20 A14 CENTER
VT/WT FUSE (8W-10-2)
21
F3 C106 10A
(8W-10-17)
A13
F20
20
VT/WT
19 20
S108
FUSE FUSE
(8W-11-7)
13 14
30A 40A
F20 (8W-10-17) (8W-10-17)
20 26 27
VT/WT
A20 B47 A10
14 14 12
C11 C10 RD/DB RD/LB RD/DG
ABS
C4 C2
SYSTEM
ABS
RELAY
PUMP
(IN PDC)
MOTOR
C13 C14 C12 RELAY
C6 C8 C3 (IN PDC)
B116 B120 Z1
B58 Z1 B47 B47 20 12 14
20 14 14 14 GY BR/WT BK
GY/LB BK RD/LB RD/LB
S110
S114 1
ABS
PUMP
M MOTOR
B47 B47
14 14
RD/LB RD/LB B120
2 12
Z1
BR/WT
12
B C
BK
S112
TO TO S106
HYDRAULIC HYDRAULIC (8W-15-2)
CONTROL CONTROL B120
UNIT UNIT 16
(8W-35-4) (8W-35-4) BR/WT
Z1
11 C2 7 C2 3 C2 12
ABS ABS ABS CONTROLLER BK
MAIN PUMP PUMP ANTI-LOCK
RELAY MOTOR MOTOR BRAKE G100
CONTROL RELAY RELAY (8W-15-2)
CONTROL OUTPUT
J998W-5 TJI03502
TJ 8W-35 ANTI-LOCK BRAKES 8W - 35 - 3
RUN A22 (8W-10-8) ST-RUN A21 (8W-10-9)

FUSE
BLOCK
(8W-11-2)
FUSE FUSE
7 10
10A 10A
(8W-11-7) (8W-11-8)
27 30
F20 G5
20 20
VT/WT DB/WT G5
A10 C202 20
DB/WT
8 C2
F3 C106 INSTRUMENT
CLUSTER
ABS (8W-40-6)
WARNING
INDICATOR
F20
20
VT/WT
4 C2 2
B14 C203 FUSED BRAKE
D2 C108 IGNITION SHIFT
SWITCH INTERLOCK
S108 OUTPUT
(8W-11-7) B SOLENOID
(ST-RUN)
ABS (8W-31-2)
DIODE
A
S146
B48
20
RD/YL
A
B48
F20 TO 20
20 G19 RD/YL
VT/WT
POWER
20
LG/OR DISTRIBUTION
CENTER
(8W-35-2)
5 C1 1 C1 5 C2
FUSED ABS ABS CONTROLLER
IGNITION WARNING MAIN ANTI-LOCK
SWITCH INDICATOR RELAY BRAKE
OUTPUT DRIVER OUTPUT
(RUN) GROUND GROUND
13 C2 14 C2
Z22 Z22
16 16
BK/PK BK/PK
S109
(8W-15-2)
Z22
14
BK/PK
G101
(8W-15-2)
TJI03503 J998W-5
FROM FROM
S114 S114
(8W-35-2) (8W-35-2)
B C
B47 B47
14 14
RD/LB RD/LB
10 1
HYDRAULIC
CONTROL
UNIT
2 7 9 4 8 3
B251 B254 B243 B245 B248 B249

20 20 20 20 20 20
WT/BK DG/OR DG/BK WT/LG DG/WT WT/DG
4 C2 12 C2 8 C2 18 C2 6 C2 15 C2
REAR REAR LEFT LEFT RIGHT RIGHT CONTROLLER
INLET OUTLET FRONT FRONT FRONT FRONT ANTI-LOCK
VALVE VALVE OUTLET INLET OUTLET INLET BRAKE
CONTROL CONTROL VALVE VALVE VALVE VALVE
CONTROL CONTROL CONTROL CONTROL
J998W-5 TJI03504
TJ 8W-35 ANTI-LOCK BRAKES 8W - 35 - 5
BATT A6 (8W-10-10)
FUSE
BLOCK
(8W-11-2)
FUSE
2
20A
(8W-11-4)
22
F32
18
PK/DB
5
BRAKE
LAMP
SWITCH DATA
(8W-51-6) LINK
6 CONNECTOR
(8W-30-13)
L50 7
18
WT/TN
D21
20
PK
POWERTRAIN
CONTROL
SCI MODULE
D9 C108 B10 C203 TRANSMIT (8W-30-13)
C27 C3
G SWITCH
D21 D21
20 18
PK PK
3 2 1 E14 C107
L50 B43 B41 B42 D21

18 20 20 20 20
WT/TN PK/OR YL/VT TN/WT PK
8 C1 2 C1 6 C1 7 C1 3 C1
BRAKE G-SWITCH G-SWITCH G-SWITCH SCI CONTROLLER
LAMP TEST NO. 1 NO. 2 TRANSMIT ANTI-LOCK
SWITCH SIGNAL SENSE SENSE BRAKE
OUTPUT
TJI03505 J998W-5
LEFT RIGHT
REAR FRONT
WHEEL WHEEL
SPEED SPEED
SENSOR SENSOR
LEFT 1 2 2 1 RIGHT
FRONT REAR
WHEEL WHEEL
SPEED SPEED
SENSOR SENSOR
B3 B4 B7 B6
18 18 18 18
1 2 LG/DB LG WT WT/DB 1 2
B8 B9 B1 B2
18 18 18 18
RD/DB RD YL/DB YL
C104 5 4 C103 C104

4 3 7 6
B3 B4 B7 B6 B1 B2
18 18 18 18 18 18
LG/DB LG WT WT/DB YL/DB YL
10 C2 9 C2 9 C1 10 C1 1 C2 2 C2 11 C1 12 C1
LEFT LEFT LEFT LEFT RIGHT RIGHT RIGHT RIGHT CONTROLLER
FRONT FRONT REAR REAR FRONT FRONT REAR REAR ANTI-LOCK
WHEEL WHEEL WHEEL WHEEL WHEEL WHEEL WHEEL WHEEL BRAKE
SPEED SPEED SPEED SPEED SPEED SPEED SPEED SPEED
SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR
(-) (+) (-) (+) (+) (-) (-) (+)
J998W-5 TJI03506
TJ 8W - 40 INSTRUMENT CLUSTER 8W - 40 - 1
8W-40 INSTRUMENT CLUSTER

ABS Diode . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-6 Headlamp Switch . . . . . . . . . . . . . . . . . . 8W-40-7, 8
ABS Warning Indicator . . . . . . . . . . . . . . . . 8W-40-6 High Beam Indicator . . . . . . . . . . . . . . . . . 8W-40-9
Airbag Control Module . . . . . . . . . . . . . . . . 8W-40-4 Ignition Switch . . . . . . . . . . . . . . . . . . . . . . 8W-40-6
Airbag Warning Indicator Lamp . . . . . . . . . 8W-40-4 Instrument Cluster . . . . . 8W-40-2, 3, 4, 5, 6, 7, 8, 9
Brake Shift Interlock Solenoid . . . . . . . . . . 8W-40-2 Key-In Switch . . . . . . . . . . . . . . . . . . . . . . . 8W-40-7
Brake Warning Indicator . . . . . . . . . . . . . . 8W-40-6 Left Turn Signal Indicator . . . . . . . . . . . . . 8W-40-9
Brake Warning Indicator Switch . . . . . . . . . 8W-40-6 Low Fuel Indicator Lamp . . . . . . . . . . . . . . 8W-40-4
Check Engine Indicator . . . . . . . . . . . . . . . 8W-40-4 Odometer/Trip Odometer . . . . . . . . . . . . . . 8W-40-4
Check Gauges Indicator . . . . . . . . . . . . . . . 8W-40-4 Oil Pressure Gauge . . . . . . . . . . . . . . . . . . . 8W-40-3
Cluster Illumination Lamps . . . . . . . . . . . . 8W-40-8 Park Brake Switch . . . . . . . . . . . . . . . . . . . 8W-40-6
Controller Anti-Lock Brake . . . . . . . . . . . . . 8W-40-6 Passenger Door Ajar Switch . . . . . . . . . . . . 8W-40-7
Data Link Connector . . . . . . . . . . . . 8W-40-3, 4, 5, 7 Power Distribution Center . . . . . . . . . . . . . 8W-40-2
Daytime Running Lamp Module . . . . . . . . . 8W-40-9 Powertrain Control Module . . . . . . . 8W-40-3, 4, 5, 7
Driver Door Ajar Switch . . . . . . . . . . . . . . . 8W-40-7 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . . . . 8W-40-8
Engine Coolant Temperature Gauge . . . . . . 8W-40-3 Rear Window Defogger Relay . . . . . . . . . . . 8W-40-8
Engine Coolant Temperature Sensor . . . . . . 8W-40-3 Rear Window Defogger Switch . . . . . . . . . . 8W-40-8
Engine Oil Pressure Sensor . . . . . . . . . . . . 8W-40-3 Right Turn Signal Indicator . . . . . . . . . . . . 8W-40-9
Fog Lamp Relay No. 2 . . . . . . . . . . . . . . . . 8W-40-9 Seat Belt Switch . . . . . . . . . . . . . . . . . . . . . 8W-40-4
Fuel Gauge . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-3 Seat Belt Warning Indicator . . . . . . . . . . . . 8W-40-5
Fuel Pump Module . . . . . . . . . . . . . . . . . . . 8W-40-3 Sound Bar Dome Lamp . . . . . . . . . . . . . . . . 8W-40-2
Fuse 3 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-8 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-3
Fuse 4 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-7 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-3
Fuse 10 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-2 Transfer Case Switch . . . . . . . . . . . . . . . . . 8W-40-5
Fuse 20 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-40-2 Trip Odometer Reset Switch . . . . . . . . . . . . 8W-40-4
Fuse Block . . . . . . . . . . . . . . . . . . . . . 8W-40-2, 7, 8 Turn Signal/Hazard Switch . . . . . . . . . . . . . 8W-40-9
G105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-5 Underhood Lamp . . . . . . . . . . . . . . . . . . . . 8W-40-2
G201 . . . . . . . . . . . . . . . . 8W-40-2, 3, 4, 5, 6, 7, 8, 9 Upshift Indicator . . . . . . . . . . . . . . . . . . . . 8W-40-5
G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-6, 7 Vehicle Speed Sensor . . . . . . . . . . . . . . . . . 8W-40-3
G302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-4 Volt Meter . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-40-3
Headlamp Dimmer Switch . . . . . . . . . . . . . 8W-40-9
8W - 40 - 2 8W-40 INSTRUMENT CLUSTER TJ
BATT A0 (8W-10-6) ST-RUN A21 (8W-10-9)

POWER FUSE
A16 DISTRIBUTION BLOCK
FUSE CENTER FUSE (8W-11-2)
20 (8W-10-2) 10
10A 10A
(8W-10-15) (8W-11-8)
A15
30
M1
20
PK/WT G5
20
D12 C108 DB/WT
M1
20
PK/WT HARD SOFT
TOP TOP
A10 C202
2
FUSED UNDERHOOD
B (+) LAMP M1 M1 M1 G5
(8W-44-3) 20 20 20 20
PK/WT PK/WT PK/WT DB/WT
TO
B7 C203 DOME 2
LAMP FUSED BRAKE
AND IGNITION SHIFT
M1 SOUND SWITCH
20 INTERLOCK
BAR TO OUTPUT
PK/WT SOUND (ST-RUN)
SOLENOID
DOME (8W-31-2)
LAMP BAR
(8W-44-2) DOME
S204 LAMP
(8W-10-15) (8W-44-2)
M1 G5
20 20
PK/WT DB/WT
9 C2 8 C2
INSTRUMENT
CLUSTER
FUSED FUSED
B(+) IGNITION
SWITCH
OUTPUT
(ST-RUN)
GROUND
6 C2 9 C1
Z2 Z2
18 18
BK/LG BK/LG
G201
(8W-15-7)
(8W-15-8)
J998W-5 TJI04002
TJ 8W-40 INSTRUMENT CLUSTER 8W - 40 - 3
BATT M1 (8W-10-15) ST-RUN G5 (8W-11-8)

INSTRUMENT
CLUSTER
VOLT OIL
METER SPEEDOMETER PRESSURE
GAUGE
FUSED VOLT FUSED SPEEDOMETER OIL

B(+) METER IGNITION CONTROL PRESSURE
CONTROL SWITCH GAUGE
OUTPUT CONTROL
(ST-RUN)
ENGINE
CCD CCD FUEL COOLANT
BUS BUS GAUGE TEMPERATURE TACHOMETER
(+) (-) CONTROL CONTROL CONTROL GROUND
FUEL ENGINE TACHOMETER

GAUGE COOLANT
TEMPERATURE
GAUGE
2 C1 1 C1 DATA 6 C2 9 C1
LINK Z2 Z2
D1 D2
20 20 CONNECTOR 18 18
VT/BR WT/BK (8W-30-14) BK/LG BK/LG
ENGINE ENGINE
TWISTED 3 11 OIL OIL
PAIR D1 D2 PRESSURE PRESSURE G201
20 20 SENSOR (8W-15-7)
SIGNAL
SENSOR
VT/BR WT/BK (8W-15-8)
(8W-30-7)
2 (8W-30-8)
B12
B11 C203
VEHICLE FUEL
D1 D2 VEHICLE SPEED FUEL PUMP
20 TWISTED 20 SPEED LEVEL
SENSOR
SENSOR SENSOR
MODULE
VT/BR PAIR WT/BK
SIGNAL (8W-30-10) SIGNAL (8W-30-3)
3 3
S302 S303
(8W-30-14) (8W-30-14) G7 K226 ENGINE ENGINE
D1 D2 20 20 COOLANT COOLANT
WT/OR DB/LG TEMPERATURE TEMPERATURE
20 TWISTED 20
SENSOR
VT/BR PAIR WT/BK SENSOR
SIGNAL
(8W-30-7)
S135 6 C103 1 (8W-30-8)
D4 D5 C108
TWISTED (8W-30-10)
PAIR
G7 G60 K226 K2
D1 D2 18 18 18 18
18 18 WT/OR GY/YL DB/LG TN/BK
VT/BR WT/BK
C30 C3 C28 C3 B27 C2 B23 C2 C26 C3 A16 C1
CCD CCD VEHICLE ENGINE FUEL ENGINE POWERTRAIN
BUS BUS SPEED OIL LEVEL COOLANT CONTROL
(+) (-) SENSOR PRESSURE SENSOR TEMPERATURE MODULE
SIGNAL SENSOR SIGNAL SENSOR (8W-30-3)
SIGNAL SIGNAL (8W-30-7)
(8W-30-8)
(8W-30-10)
(8W-30-14)
TJI04003 J998W-5
BATT M1 (8W-10-15) ST-RUN G5 (8W-11-8)

INSTRUMENT
CLUSTER
AIRBAG LOW CHECK CHECK
WARNING FUEL ENGINE GAUGES
INDICATOR INDICATOR INDICATOR INDICATOR
FUSED AIRBAG FUSED LOW CHECK CHECK

B(+) WARNING IGNITION FUEL ENGINE GAUGES
INDICATOR SWITCH INDICATOR INDICATOR INDICATOR
SEAT
DRIVER OUTPUT DRIVER DRIVER DRIVER
CCD CCD BELT
(ST-RUN)
BUS BUS SWITCH
(+) (-) ODOMETER CONTROL TRIP RESET GROUND SENSE
TRIP
ODOMETER
ODOMETER/
RESET
TRIP
SWITCH
ODOMETER
2 C1 1 C1 6 C2 9 C1 10 C1
DATA
Z2 Z2 G10
LINK 18 18 20
D1 D2
20 20 CONNECTOR BK/LG BK/LG LG/RD
VT/BR WT/BK (8W-30-14)
3 11 G201 C3 C204
TWISTED (8W-15-7)
PAIR D1 D2 (8W-15-8)
20 20 LHD RHD
VT/BR WT/BK
G6 C322 6 C322
B12
B11 C203
G10
20
D1 D2
LG/RD
20 TWISTED 20
VT/BR PAIR WT/BK
1
SEAT
S303 BELT
(8W-30-14) SWITCH
S302
(8W-30-14) (EXCEPT LHD
D1 D2 BUILT-UP
20 20 TWISTED 2
VT/BR WT/BK PAIR -EXPORT)
D1 D2 Z1
TWISTED 18 18 20
PAIR VT/BR WT/BK BK
D4 C108 19 18 S309
D5
TWISTED CCD CCD AIRBAG (8W-15-11)
PAIR BUS BUS CONTROL Z1
(+) (-) MODULE 12
(8W-43-3) BK
D1 D2
18 18 LHD RHD
VT/BR WT/BK 5 C322
G5 C322
C30 C3 C28 C3
CCD CCD POWERTRAIN
BUS BUS CONTROL G302
(+) (-) MODULE (8W-15-11)
(8W-30-14)
J998W-5 TJI04004
BATT M1 (8W-10-15) ST-RUN G5 (8W-11-8)

INSTRUMENT
CLUSTER
SENTRY SEAT UPSHIFT 4WD
KEY BELT INDICATOR INDICATOR
IMMOBILIZER WARNING
MODULE (M/T)
INDICATOR
INDICATOR
FUSED SENTRY FUSED SEAT UPSHIFT

B(+) KEY IGNITION BELT INDICATOR
IMMOBILIZER SWITCH WARNING DRIVER
MODULE OUTPUT INDICATOR (M/T)
INDICATOR (ST-RUN) DRIVER
CCD DRIVER CCD
BUS BUS
(+) (-) GROUND
2 C1 1 C1 6 C2 9 C1 5 C1
G107
Z2 Z2 20
DATA 18 18 BK/RD
D1 D2
LINK BK/LG BK/LG
20 20
VT/BR WT/BK CONNECTOR 5 C170
(8W-30-14)
G201
TWISTED 3 11 (8W-15-7)
PAIR (8W-15-8)
D1 D2 G107
20 20 20
VT/BR WT/BK BK/RD
B11 B12
C203 13 C103
D1 D2
20 TWISTED 20 G107
VT/BR WT/BK 20
PAIR BK/RD
A
S302 S303 TRANSFER
(8W-30-14) (8W-30-14) CASE
D1 D2 SWITCH
20 20 (8W-31-2)
VT/BR WT/BK
TWISTED B
PAIR
Z1
20
D4 D5 C108 BK
TWISTED
PAIR
S132
D1 D2 (8W-15-6)
18 18
VT/BR WT/BK Z1
14
C30 C3 C28 C3 BK
CCD CCD POWERTRAIN
BUS BUS CONTROL
(+) (-) MODULE G105
(8W-30-14) (8W-15-6)
TJI04005 J998W-5
ST-RUN G5 (8W-11-8) BATT M1 (8W-10-15)

INSTRUMENT
CLUSTER
FUSED FUSED
BRAKE ABS IGNITION B(+)
WARNING WARNING SWITCH
INDICATOR INDICATOR OUTPUT
(ST-RUN)
GROUND
2 C2 4 C2 6 C2 9 C1
G99 G19
20 20 Z2 Z2
GY/WT LG/OR 18 18
BK/LG BK/LG
B14 C203
3 C170 OTHERS ABS
G201
(8W-15-7)
G99 D2 C108
(8W-15-8)
20
GY/WT
2 G19 G19 G19

BRAKE 20 20 20
WARNING LG/OR LG/OR LG/OR
INDICATOR
SWITCH
B 1 C1
D2 C108 ABS ABS ABS CONTROLLER
1 NOT WARNING DIODE WARNING ANTI-LOCK
USED INDICATOR (8W-35-3) INDICATOR BRAKE
G9
DRIVER DRIVER (8W-35-3)
20
GY/BK
F11 C106
G9 20 GY/BK
2
G9 IGNITION
20
GY/BK SWITCH
1 4 1 START
LHD RHD 2 RUN
2 0 3
0 OFF
G9 C322 9 C322 3 LOCK
1 4 ACC
(8W-10-9)
Z1
16
G9 BK
20
GY/BK S304
(8W-15-9)
Z1 (8W-15-10)
16
PARK BK
BRAKE
G300
SWITCH (8W-15-9)
(8W-15-10)
J998W-5 TJI04006
BATT M1 (8W-10-15) ST-RUN G5 (8W-11-8)

INSTRUMENT
CLUSTER
FUSED FUSED
B(+) IGNITION
SWITCH
KEY-IN OUTPUT
CCD CCD IGNITION (ST-RUN)
BUS BUS SWITCH
(+) (-) GROUND SENSE
2 C1 1 C1 6 C2 9 C1 8 C1
Z2 Z2 G26 20LB
D1 D2 18 18
20 20 BK/LG BK/LG G26 20 LB
VT/BR WT/BK
5
G201 HEADLAMP B3 C203
(8W-15-7) SWITCH 2
(8W-15-8) 0 OFF KEY-IN
1 PARK SWITCH
DATA 0 1 2 2 HEAD
LINK (8W-50-3)
TWISTED
CONNECTOR
PAIR (8W-30-14) 6 1
G16 G16
3 11 20 20
D1 D2 BK/LB BK/LB
20 20
VT/BR WT/BK B4 C203
G16 20BK/LB
B12 3
B11 C203
PASSENGER DRIVER
DOOR DOOR DOOR
D1 D2
AJAR AJAR AJAR
20 TWISTED 20
SWITCH
VT/BR WT/BK SWITCH SWITCH
PAIR OUTPUT
(8W-44-4) (8W-44-4)
1 1
M23 M23
S302 S303 20 20
(8W-30-14) (8W-30-14) YL/BK YL/BK
D1 D2
20 TWISTED 20 4
VT/BR PAIR WT/BK FUSE
FUSE
BLOCK
4 (8W-11-2)
D4 D5 C108 10A
TWISTED (8W-11-5)
PAIR 24
LHD RHD
D1 D2
18 18 Z1 20BK
VT/BR WT/BK Z1
S304 20
C30 C3 C28 C3 (8W-15-9) BK
CCD CCD POWERTRAIN
Z1 16BK
BUS BUS CONTROL
(+) (-) MODULE
(8W-30-14)
G300
(8W-15-9)
TJI04007 J998W-5
(8W-15-10)
BATT F34 (8W-11-4)

HEADLAMP
SWITCH
0 HEAD
1 PARK
0 1 2 3 4 5 2 HEAD
3 DOME
4 MAX
1 5 MIN
E1 (8W-50-2)
RUN F20 (8W-11-7) 18
REAR TN
WINDOW A3 C202
DEFOGGER 3
RELAY FUSE
D6 (IN PDC) BLOCK
FUSE (8W-11-2)
(8W-48-2)
3
10A
(8W-11-4)
C81
20
LB/WT 23
E2
20 E2
OR 20
2 C170 OR
A4 C202 1
FUSED PRNDL
S206 PANEL LAMP
(8W-11-4) LAMPS (8W-44-5)
C81
DIMMER
20
E2 SWITCH
LB/WT
20 SIGNAL
OR
BATT M1 (8W-10-15) ST-RUN G5 (8W-11-8)

3 C1 3 C2
INSTRUMENT
CLUSTER
FUSED REAR FUSED
B(+) WINDOW IGNITION CLUSTER
DEFOGGER SWITCH ILLUMINATION
REAR RELAY OUTPUT LAMPS
WINDOW CONTROL (ST-RUN)
DEFOGGER
SWITCH
SENSE GROUND
4 C1 6 C2 9 C1
C80
20
DB/LG Z2 Z2
18 18
BK/LG BK/LG
2
REAR REAR
WINDOW WINDOW
DEFOGGER DEFOGGER G201
SWITCH (8W-15-7)
SENSE
SWITCH
(8W-15-8)
(HARD TOP)
(8W-48-2)
J998W-5 TJI04008
HEADLAMP
DIMMER
SWITCH DIMMER
HIGH SWITCH
BEAM (8W-50-2)
TURN
OUTPUT SIGNAL/
3 HAZARD
L3
SWITCH
14 LEFT RIGHT (8W-52-3)
RD/OR TURN TURN
SIGNAL SIGNAL
E4 C107 10 1
L3
16
RD/OR
S105 L61 L60

(8W-50-2) 18 18
GY TN
OTHER DRL
L3
16
L3
RD/OR
16
RD/OR
G34
18
RD/GY
B2 C203 B1 C203
4 1
HIGH DIMMER DAYTIME
BEAM SWITCH RUNNING
INDICATOR HIGH LAMP
DRIVER BEAM
OUTPUT
MODULE
(8W-50-8)
D7 C108
G34
16 G34 L61 L60
RD/GY 16 18 18
RD/GY GY TN
1
B5 C203 HIGH FOG LAMP
BEAM RELAY
INDICATOR NO. 2
G34 DRIVER
(EXCEPT
16
RD/GY
BUILT-UP
-EXPORT)
(8W-50-6)
5 C2 10 C2 6 C1
INSTRUMENT
HIGH LEFT RIGHT CLUSTER
BEAM TURN TURN
INDICATOR SIGNAL SIGNAL
INDICATOR INDICATOR
6 C2 9 C1
Z2 Z2
18 18
BK/LG BK/LG
G201
(8W-15-7)
TJI04009 (8W-15-8) J998W-5
TJ 8W - 41 HORN/CIGAR LIGHTER/POWER OUTLET 8W - 41 - 1
8W-41 HORN/CIGAR LIGHTER/POWER OUTLET

Brake Lamp Switch . . . . . . . . . . . . . . . . . . 8W-41-2 G200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-41-2
Cigar Lighter/Accessory Relay . . . . . . . . . . 8W-41-2 G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-41-2
Cigar Lighter/Power Outlet . . . . . . . . . . . . 8W-41-2 High Note Horn . . . . . . . . . . . . . . . . . . . . . 8W-41-3
Clockspring . . . . . . . . . . . . . . . . . . . . . . . . . 8W-41-3 Horn Relay . . . . . . . . . . . . . . . . . . . . . . . . . 8W-41-3
Fuse 5 (PDC) . . . . . . . . . . . . . . . . . . . . . . . 8W-41-2 Horn Switch . . . . . . . . . . . . . . . . . . . . . . . . 8W-41-3
Fuse 17 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-41-3 Ignition Switch . . . . . . . . . . . . . . . . . . . . . . 8W-41-2
Fuse 19 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-41-2 Low Note Horn . . . . . . . . . . . . . . . . . . . . . . 8W-41-3
Fuse Block . . . . . . . . . . . . . . . . . . . . . . . . . 8W-41-2 Power Distribution Center . . . . . . . . . . . 8W-41-2, 3
G102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-41-3
8W - 41 - 2 8W-41 HORN/CIGAR LIGHTER/POWER OUTLET TJ
BRAKE BATT A0 (8W-10-6)

LAMP POWER
SWITCH DISTRIBUTION
(8W-51-6) 11
GROUND CENTER
2 FUSE (8W-10-2)
BATT A1 (8W-10-9) 5
40A
IGNITION (8W-10-10)
4
SWITCH
1 START
2 RUN
1 4 0 OFF F30
3 LOCK 12
2 0 3
4 ACC RD/PK
(8W-10-9)
F1 C106
8
S307 S332
(8W-10-9) (8W-10-10)
A31 F30
14 12
BK/DG RD/PK
2 1
CIGAR
LIGHTER/
Z1 ACCESSORY
20 RELAY
BK
5 4
F22
12
Z1 WT/PK
20
19
BK
FUSE
FUSE
BLOCK
LHD RHD 19 (8W-11-2)
20A
(8W-11-10)
S304
(8W-15-10)
39
Z1 Z1 A9 C202
20 16
BK BK F38
16
LB
1
CIGAR
LIGHTER/
POWER
G300 F38
(8W-15-9) OUTLET
16
(8W-15-10) LB 3
Z1
SWITCH 16
AUXILIARY BK
POWER
(TAPED TO S207
HARNESS (8W-15-7)
IN FB T/O) (8W-15-8)
G200
(8W-15-7)
J998W-5 (8W-15-8) TJI04102
TJ 8W-41 HORN/CIGAR LIGHTER/POWER OUTLET 8W - 41 - 3
BATT A0 (8W-10-6)
POWER
DISTRIBUTION
A21
CENTER
FUSE (8W-10-2)
17
20A
(8W-10-16)
A22
F31 F31
18 18
VT VT
B13 B11
HORN
RELAY
(IN PDC)
B15 B12
X2
X3 18
20 WT/RD
RD/YL
6 C110
X2
18
WT/RD
BUILT- EXCEPT BUILT-

E7 C107 UP-EXPORT UP-EXPORT
S115
X3
20 X2 X2
RD/YL 18 18
WT/RD WT/RD
1 1
HIGH LOW
NOTE NOTE
HORN HORN
1 C2 2 2
CLOCKSPRING
(8W-30-15) Z1 Z1
18 18
BK BK
S117
(8W-15-3)
HORN
SWITCH Z1
16
BK
G102
(8W-15-3)
TJI04103 J998W-5
TJ 8W - 42 AIR CONDITIONING-HEATER 8W - 42 - 1
8W-42 AIR CONDITIONING-HEATER

A/C Compressor Clutch . . . . . . . . . . . . . . . . 8W-42-4 Fuse 11 (PDC) . . . . . . . . . . . . . . . . . . . . . 8W-42-2, 3
A/C Compressor Clutch Relay . . . . . . . . . . . 8W-42-4 Fuse 16 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-42-4
A/C Heater Control . . . . . . . . . . . . . . . 8W-42-2, 3, 4 Fuse Block . . . . . . . . . . . . . . . . . . . . . 8W-42-2, 3, 4
A/C High Pressure Switch . . . . . . . . . . . . . 8W-42-4 G105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-42-4
A/C Low Pressure Switch . . . . . . . . . . . . . . 8W-42-4 G200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-42-2, 3
Blend Door Actuator . . . . . . . . . . . . . . . . 8W-42-2, 3 G202 . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-42-2, 3, 4
Blower Motor . . . . . . . . . . . . . . . . . . . . . 8W-42-2, 3 G203 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-42-2, 3
Blower Motor Relay . . . . . . . . . . . . . . . . 8W-42-2, 3 HVAC Unit . . . . . . . . . . . . . . . . . . . . . . . 8W-42-2, 3
Fuse 7 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-42-4 Power Distribution Center . . . . . . . . . 8W-42-2, 3, 4
Fuse 8 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-42-2, 3 Powertrain Control Module . . . . . . . . . . . . . 8W-42-4
8W - 42 - 2 8W-42 AIR CONDITIONING-HEATER TJ
HEATER ONLY
RUN A22 (8W-10-8) BATT A0 (8W-10-6)
FUSE POWER
FUSE (8W-11-2) FUSE CENTER
8 11 (8W-10-2)
10A 40A
(8W-11-7) 24 (8W-10-13)
28
A111
F24 12
20 RD/LB
RD/DG
F12 C106
A1 A12 C202
F24 20RD/DG
F24
F24 20 A111
20 RD/DG 12
RD/DG RD/LB
5 9 8
HVAC
BLOWER
UNIT
BLOWER MOTOR
M MOTOR RELAY
FROM
S206 BLEND
(8W-11-4) DOOR
M
ACTUATOR
E2
20
OR
2 3 4 7 6 1 10
C4 C5 C6 C7 C1 C36
16 16 14 12 12 20
1 TN LG/LB LB BR/TN DG DB/RD
4 C2 3 C2 D C1 C C1 B C1 A C1 E C1 B C3 2 C2
A/C-
HEATER
7 6 CONTROL
Z1
8 5 0 OFF
20
1 VENT
BK
2 HEAT
3 MIX
2 1 4 DEFROST
3
4 0 5 HIGH
6 M2
7 M1
8 LOW
5 C2 C C3 1 C2
3
Z1 Z1 Z1 Z11 Z11
20 12 20 20 G200
16
BK BK BK/WT BK/WT (8W-15-7)
BK
(8W-15-8)
LHD
S207 G202 G203
(8W-15-7) G200 RHD
(8W-15-7) (8W-15-7)
(8W-15-8) (8W-15-7) (8W-15-8) (8W-15-8)
J998W-5 (8W-15-8) TJI04202
TJ 8W-42 AIR CONDITIONING-HEATER 8W - 42 - 3
RUN A22 (8W-10-8) BATT A0 (8W-10-6)

FUSE POWER
FUSE (8W-11-2) FUSE CENTER
8 11 (8W-10-2)
10A 40A
(8W-11-7) 24 (8W-10-13)
28
F24 A111
20 12
RD/DG RD/LB
F12 C106
A1 A12 C202
F24 20RD/DG
F24 F24 A111
20 20 12
RD/DG RD/DG RD/LB
5 9 8
HVAC
BLOWER
UNIT
BLOWER MOTOR
M MOTOR RELAY
FROM BLEND
S206 M DOOR
(8W-11-4) ACTUATOR
E2
20
OR 2 3 4 7 6 1 10
C4 C5 C6 C7 C1 C36
16 16 14 12 12 20
TN LG/LB LB BR/TN DG DB/RD
1
4 C2 3 C2 D C1 C C1 B C1 A C1 E C1 B C3 2 C2
A/C-
9 8 HEATER
10 7 CONTROL
Z1
0 OFF
20
1 MAX
BK
2 NORM
3 3 3 3 VENT
4 2 4 2 4 2 4 HEAT
5 MIX
5 1 5 1 5 1 6 DEFROST
7 HIGH
6 0 6 0 6 0 8 M2
9 M1
10 LOW
5 C2 A C3 C C3 1 C2
Z1 C90 Z1 3 Z11 Z11 G200
20 FROM 20 12 20 20 (8W-15-7)
BK Z1 S103 LG BK BK/WT BK/WT (8W-15-8)
16
BK
(8W-42-4) 6 C170
S207 G202 G203
(8W-15-7) (8W-15-7) (8W-15-7)
(8W-15-8) LHD (8W-15-8)
(8W-15-8) G200
RHD
(8W-15-7)
TJI04203 J998W-5
(8W-15-8)
8W - 42 - 4 8W-42 AIR CONDITIONING-HEATER TJ
POWERTRAIN
A/C CONTROL
COMPRESSOR MODULE
A/C A/C CLUTCH (8W-30-3)
SWITCH SELECT RELAY (8W-30-12)
SENSE INPUT CONTROL
C22 C3 C23 C3 C1 C3 RUN A22 (8W-10-9)
C22 C90 C13 FUSE
18 18 18
DB/WT LG DB/OR BLOCK
FUSE (8W-11-2)
2 C104 7
C22 10A
20 (8W-11-7)
DB/WT
1
27
A/C
LOW F20
PRESSURE 20 BATT A0 (8W-10-6)
VT/WT
SWITCH POWER
2 F3 C106 DISTRIBUTION
A23
C21 F20 CENTER
20 20 FUSE (8W-10-2)
DB/OR VT/WT 16
10A
2 S108 (8W-10-16)
A24
A/C (8W-11-7)
HIGH F20 A17
PRESSURE 20 20
SWITCH VT/WT RD/GY
1 B8 B6
C90 A/C
20 COMPRESSOR
LG CLUTCH
1 C104 RELAY
C90 B10 B7 (IN PDC)
20 C3
LG 20
DB/BK
S103 14 C103
C3
C90 20
20 DB/BK
LG
1
6 C170 A/C
COMPRESSOR
A C3
CLUTCH
A/C
HEATER
3
4 2 CONTROL
0 OFF 2
5 1 1 MAX
2 NORM Z1
6 0 3 VENT 20
4 HEAT BK
5 MIX
C C3 6 DEFROST S132
Z1 (8W-15-6)
12 Z1
BK 14
BK
G202
(8W-15-7)
(8W-15-8)
G105
(8W-15-6)
J998W-5 TJI04204
TJ 8W - 43 AIRBAG SYSTEM 8W - 43 - 1
8W-43 AIRBAG SYSTEM

Airbag Control Module . . . . . . . . . . . . . . 8W-43-2, 3 Fuse 9 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-43-2
Airbag Warning Indicator . . . . . . . . . . . . . . 8W-43-3 Fuse 10 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-43-3
Brake Shift Interlock Solenoid . . . . . . . . . . 8W-43-3 Fuse Block . . . . . . . . . . . . . . . . . . . . . . . 8W-43-2, 3
Clockspring . . . . . . . . . . . . . . . . . . . . . . . . . 8W-43-2 G301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-43-2
Data Link Connector . . . . . . . . . . . . . . . . . 8W-43-3 Instrument Cluster . . . . . . . . . . . . . . . . . . . 8W-43-3
Driver Airbag Squib . . . . . . . . . . . . . . . . . . 8W-43-2 Passenger Airbag . . . . . . . . . . . . . . . . . . . . 8W-43-2
Fuse 5 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-43-2 Passenger Airbag On/Off Switch . . . . . . . . . 8W-43-2
8W - 43 - 2 8W-43 AIRBAG SYSTEM TJ
ST-RUN A21 (8W-10-9) RUN A22 (8W-10-8)
FUSE
BLOCK
(8W-11-2)
FUSE FUSE
9 5
10A 10A
(8W-11-8) (8W-11-6)
29 25
F14 F23
18 18
LG/YL DB/YL
17 20
FUSED FUSED AIRBAG
IGNITION IGNITION CONTROL
SWITCH SWITCH MODULE
F14 OUTPUT OUTPUT
18 (ST-RUN) (RUN)
LG/YL
PASSENGER PASSENGER DRIVER DRIVER

AIRBAG SQUIB AIRBAG SQUIB AIRBAG AIRBAG
LINE 2 LINE 1 GROUND LINE 1 LINE 2
6 5 10 2 1
R144 R142
18 18
R43 R45
VT/YL BR/YL
18 18
BK/LB DG/LB
1 C1 2 C2 1 C2
TWISTED
PASSENGER PAIR
Z6
AIRBAG 18
ON/OFF BK/PK
SWITCH 2 C1 1 C1
CLOCKSPRING
FUSED
RESISTOR
R43 R45
18 18
BK/LB DG/LB
2 C1 4 C2 3 C2 G301
(8W-15-11)
R44 R42
18 18
Z6 DG/YL BK/YL
20 DRIVER DRIVER DRIVER
BK/PK A B
AIRBAG AIRBAG AIRBAG
PASSENGER PASSENGER PASSENGER LINE 1 LINE 2 SQUIB
G301 AIRBAG AIRBAG AIRBAG
(8W-15-11) LINE 2 LINE 1
J998W-5 TJI04302
TJ 8W-43 AIRBAG SYSTEM 8W - 43 - 3
ST-RUN A21 (8W-10-9)
AIRBAG FUSE
CONTROL BLOCK
(8W-11-2)
MODULE FUSE
10
CCD CCD 10A
BUS BUS (8W-11-8)
(-) (+)
30
18 19
G5
20
D2 D1 DB/WT G5
18 18 20
WT/BK VT/BR DB/WT
A10 C202
TWISTED
PAIR 2
G5 FUSED BRAKE
20 IGNITION SHIFT
DB/WT SWITCH INTERLOCK
OUTPUT
(ST-RUN)
SOLENOID
S303 S302 (8W-31-2)
(8W-30-14) (8W-30-14)
8 C2
D2 D1 INSTRUMENT
20 TWISTED 20 CLUSTER
WT/BK PAIR VT/BR DATA AIRBAG (8W-40-2)
LINK WARNING
INDICATOR
CONNECTOR
(8W-30-14)
3 11 AIRBAG
D1 D2 WARNING
20 20 CCD INDICATOR CCD
VT/BR WT/BK BUS DRIVER BUS
C203 (+) (-)
B12 B11
2 C1 1 C1
TWISTED
PAIR
D1 D2
20 20
VT/BR WT/BK
TJI04303 J998W-5
TJ 8W - 44 INTERIOR LIGHTING 8W - 44 - 1
8W-44 INTERIOR LIGHTING

A/C Heater Control . . . . . . . . . . . . . . . . . . . 8W-44-5 Key-In Switch . . . . . . . . . . . . . . . . . . . . . . . 8W-44-4
Dome Lamp . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-2 Left Courtesy Lamp . . . . . . . . . . . . . . . . . . 8W-44-4
Driver Door Ajar Switch . . . . . . . . . . . . . . . 8W-44-4 Mercury Switch . . . . . . . . . . . . . . . . . . . . . . 8W-44-3
Front Fog Lamp Switch . . . . . . . . . . . . . . . 8W-44-5 Passenger Door Ajar Switch . . . . . . . . . . . . 8W-44-4
Fuse 3 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-44-5, 6 Power Distribution Center . . . . . . . . . . . 8W-44-2, 4
Fuse 4 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-4 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . . . . 8W-44-5
Fuse 20 (PDC) . . . . . . . . . . . . . . . . . . . . . 8W-44-2, 4 Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-6
Fuse Block . . . . . . . . . . . . . . . . . . . . . 8W-44-4, 5, 6 Rear Fog Lamp Switch . . . . . . . . . . . . . . . . 8W-44-5
G100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-3 Rear Window Defogger Switch . . . . . . . . . . 8W-44-5
G200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-4, 5 Rear Wiper/Washer Switch . . . . . . . . . . . . . 8W-44-5
G201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-6 Right Courtesy Lamp . . . . . . . . . . . . . . . . . 8W-44-4
G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-4, 5 Sound Bar Dome Lamp . . . . . . . . . . . . . . 8W-44-2, 4
Headlamp Switch . . . . . . . . . . . . . . . . 8W-44-4, 5, 6 Underhood Lamp . . . . . . . . . . . . . . . . . . 8W-44-3, 4
Instrument Cluster . . . . . . . . . . . . . . . . . 8W-44-4, 6
8W - 44 - 2 8W-44 INTERIOR LIGHTING TJ
BATT A0 (8W-10-6)
POWER
A16 DISTRIBUTION
FUSE CENTER
20 (8W-10-2)
10A
A15 (8W-10-15)
M1
20
M1 HARD PK/WT SOFT
20 TOP TOP
PK/WT
LHD RHD 4 SPEAKER LHD 2 RHD 2
M1 H2 C323 2 C323 SYSTEM SPEAKER SYSTEM SPEAKER SYSTEM
D12 C108
20
PK/WT M1 M1 M1 M1
20 20 20 20
M1
PK/WT PK/WT PK/WT PK/WT
20
PK/WT 2 SPEAKER 4 SPEAKER
B SYSTEM SYSTEM
H2 C323 2 C323
B7 C203 LHD RHD NOT NOT
TO S313 USED USED
UNDERHOOD M1 H2 C323 2
C323
20
LAMP PK/WT
(8W-44-3) 8 C326
8 C331 3 C325
TO M1 3 C330
20
S204 PK/WT
M1
(8W-10-15) 20
PK/WT
DOME 1
LAMP SOUND
BAR
DOME
LAMP
M2 20YL
2
9 C331 M2
M2 20
18 YL
YL 4 C330
9 C326 4 C325
S314 LHD RHD

H3 C323 3 C323 NOT NOT
2 SPEAKER 4 SPEAKER USED USED
SYSTEM M2 SYSTEM H3 C323 3 C323
20 M2 M2 M2
YL 20 20 20
LHD RHD YL YL YL
H3 C323 3 C323 4 SPEAKER LHD 2 RHD 2 SPEAKER

SYSTEM SPEAKERSYSTEM SYSTEM
HARD SOFT
TOP M2 TOP
20
YL
TO
S301
(8W-44-4)
J998W-5 TJI04402
TJ 8W-44 INTERIOR LIGHTING 8W - 44 - 3
FROM
C108
(8W-44-2)
B
M1
20
PK/WT
2
UNDERHOOD
LAMP
MERCURY
SWITCH
BASE OTHER
Z1
18
BK
Z1
18 S106
BK (8W-15-2)
Z1
12
BK
G100 G100
(8W-15-2) (8W-15-2)
TJI04403 J998W-5
BATT A0 (8W-10-6)
UNDERHOOD INSTRUMENT
POWER LAMP CLUSTER
A16 DISTRIBUTION KEY-IN
(8W-44-3) IGNITION (8W-40-7)
FUSE CENTER FUSED
B (+) SWITCH
20 (8W-10-2) SENSE
10A 2
A15 (8W-10-15)
M1 8 C1
M1 20
G26 20LB
20 PK/WT
PK/WT
G26 20LB
12 C108 5
HEADLAMP B3 C203
B7 C203
SWITCH
S204 HARD SOFT 0 OFF G26
(8W-10-15) FROM TOP TOP 1 PARK 20
M1 M1 DOME 0 2 HEAD LB
20 20 1 2
PK/WT PK/WT LAMP M1 M1 (8W-50-3)
AND 20 20
2
1 PK/WT PK/WT
SOUND 6 KEY-IN
BAR G16 SWITCH
LEFT TO TO 20
DOME
COURTESY LAMP DOME SOUND BK/LB
LAMP 1 LAMP BAR
(8W-44-2) B4 C203 1
AND DOME
A SOUND LAMP G16 20BK/LB
RIGHT G16
BAR (8W-44-2)
COURTESY M2 20
LAMP DOME BK/LB
20
YL LAMP
2 (8W-44-2)
S301
M2 M2 M2
2 20 20 20
YL YL YL
C5 C204 2 2 3
PASSENGER DRIVER
M2 M2 M2
20 20 20
DOOR DOOR
YL YL YL AJAR AJAR
SWITCH SWITCH
S202
1 1
M2 M23 M23
20 20 20
YL YL/BK YL/BK
3 4
HEADLAMP FUSE
SWITCH FUSE
BLOCK
0 OFF 4 (8W-11-2)
0 1 1 DOME 10A
(8W-50-3) (8W-11-5)
RHD LHD 24
Z1
Z1 Z1 20
16 16 BK
BK BK RHD LHD
S207 Z1 S304
(8W-15-8) 20 (8W-15-9)
Z1 Z1
16 BK 16
BK BK
G200 G200 G300 G300

(8W-15-8) (8W-15-7) (8W-15-10) (8W-15-9)
J998W-5 TJI04404
TJ 8W-44 INTERIOR LIGHTING 8W - 44 - 5
BATT F34 (8W-11-4)

HEADLAMP
SWITCH
0 OFF
1 PARK S206
0 1 2 HEAD (8W-11-4)
2 3 4 5
3 DOME
4 MAX
1 5 MIN E2 E2 E2 E2 E2 E2
(8W-50-2) 20 20 20 20 20 20
E1
OR OR OR OR OR OR
18
TN
A4
A3 C202
3
FUSE
BLOCK 1
FUSE (8W-11-2) FRONT
3 FOG
10A E2
(8W-11-4) 20 LAMP
OR SWITCH
23 (EXCEPT
4 BUILT-UP
-EXPORT)
(8W-50-7)
E2 4 4 C2
20 REAR A/C-
OR WINDOW HEATER
DEFOGGER CONTROL
SWITCH (8W-42-2)
(HARD TOP) (8W-42-3)
1 (8W-48-2)
1 4 3
5 C2
PRNDL REAR REAR
LAMP FOG WIPER/
LAMP WASHER
SWITCH SWITCH
(BUILT-UP (HARD TOP)
2 1 -EXPORT) 1 (8W-53-4)
(8W-51-7)
(8W-51-8)
Z1 Z1 Z1 Z1 Z1 Z1
20 20 20 18 20 20
BK BK BK BK/WT BK BK
S304 S207
(8W-15-9) (8W-15-7)
(8W-15-10) (8W-15-8)
Z1 Z1
16 16
BK BK
G300 G200
(8W-15-9) (8W-15-7)
(8W-15-10) (8W-15-8)
TJI04405 J998W-5
BATT F34 (8W-11-4)

HEADLAMP
SWITCH
0 OFF
1 PARK
0 1 2 3 4 5 2 HEAD
3 DOME
4 MAX
1 5 MIN
E1 (8W-50-2)
18
TN
A3 C202
E1
18
TN
3
FUSE
BLOCK
FUSE (8W-11-2)
3
10A
(8W-11-4)
23
E2
20
E2
OR
20
OR
A4 C202
E2 TO
20
OR
PRNDL
LAMP
(8W-44-5)
S206
(8W-11-4)
E2
20
OR
3 C2
INSTRUMENT
E2
CLUSTER 20
(8W-40-8) OR
5 C1
RADIO
(8W-47-2)
6 C2
Z2
18
BK/LG
G201
(8W-15-7)
(8W-15-8)
J998W-5 TJI04406
TJ 8W - 47 AUDIO SYSTEM 8W - 47 - 1
8W-47 AUDIO SYSTEM

Fuse 3 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-47-2 Power Distribution Center . . . . . . . . . . . . . 8W-47-2
Fuse 15 (FB) . . . . . . . . . . . . . . . . . . . . . . . . 8W-47-2 Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-47-2, 3
Fuse 20 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-47-2 Radio Antenna . . . . . . . . . . . . . . . . . . . . . . 8W-47-2
Fuse Block . . . . . . . . . . . . . . . . . . . . . . . . . 8W-47-2 Right Front Speaker . . . . . . . . . . . . . . . . . . 8W-47-3
Headlamp Switch . . . . . . . . . . . . . . . . . . . . 8W-47-2 Right Rear Speaker . . . . . . . . . . . . . . . . . . 8W-47-3
Left Front Speaker . . . . . . . . . . . . . . . . . . . 8W-47-3 Sound Bar Dome Lamp . . . . . . . . . . . . . . . . 8W-47-2
Left Rear Speaker . . . . . . . . . . . . . . . . . . . . 8W-47-3 Underhood Lamp . . . . . . . . . . . . . . . . . . . . 8W-47-2
8W - 47 - 2 8W-47 AUDIO SYSTEM TJ
RUN-ACC A31 (8W-10-9) BATT A0 (8W-10-6)

FUSE POWER
BLOCK A16 DISTRIBUTION
FUSE FUSE (8W-11-2) FUSE CENTER
15 3 20 (8W-10-2)
10A 10A 10A
(8W-11-9) (8W-11-4) A15 (8W-10-15)
35 3 23
X12 E1 E2 M1
20 18 20 20
PK TN OR PK/WT
C10 C204 D12 C108

A3 C202
E1 M1 M1 M1
18 20 20 20
TN PK/WT PK/WT PK/WT
HARD SOFT
TOP TOP
BATT F34 (8W-11-4)
1 TO
HEADLAMP UNDERHOOD
SWITCH LAMP TO TO
0 OFF
(8W-44-3) DOME SOUND
1 HEAD LAMP BAR
1 0 2 PARK
2 4 5 4 MAX AND DOME
5 MIN SOUND LAMP
9 (8W-50-2) BAR (8W-44-2)
A4 C202 DOME
LAMP
(8W-44-2)
L7
18
BK/YL E2
20 B7 C203
OR RADIO
M1 ANTENNA
20
PK/WT
B6 C203 S206
(8W-11-4) S204
(8W-10-15)
X12 L7 E2 M1
20 18 20 20
PK BK/YL OR PK/WT
6 C1 4 C1 5 C1 7 C1
FUSED HEADLAMP FUSED FUSED ANTENNA RADIO
IGNITION SWITCH PANEL B (+)
SWITCH OUTPUT LAMPS
OUTPUT DIMMER
(RUN-ACC) SWITCH
SIGNAL
J998W-5 TJI04702
TJ 8W-47 AUDIO SYSTEM 8W - 47 - 3
2 2
LEFT RIGHT
REAR REAR
2 2
SPEAKER SPEAKER
(SOUND (SOUND
LEFT RIGHT
1 BAR) 1 BAR)
FRONT FRONT
SPEAKER SPEAKER
X57 X51 X58 X52
1 1 20 20 20 20
BR/LB BR/YL DB/PK DB/WT
1 2 5 6 C330
X57 X51 X58 X52

18 18 18 18
1 2 5 6 C325
X58 X52
18 18
DB/PK DB/WT
LHD RHD
X57 X51
18 18
H10 H9
BR/LB BR/YL C323 10 9 C323
LHD RHD
H8 H7
C323 8 7 C323
X57 X51 X58 X52

18 18 18 18
C12 C11 C14 C13 C204
X55 X53 X56 X54 X57 X51 X58 X52

18 18 18 18 18 18 18 18
BR/RD DG DB VT BR/LB BR/YL DB/PK DB/WT
2 C1 4 C2 3 C1 5 C2 6 C2 2 C2 7 C2 3 C2
LEFT LEFT RIGHT RIGHT LEFT LEFT RIGHT RIGHT RADIO
FRONT FRONT FRONT FRONT REAR REAR REAR REAR
SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER
(-) (+) (-) (+) (-) (+) (-) (+)
TJI04703 J998W-5
TJ 8W - 48 REAR WINDOW DEFOGGER 8W - 48 - 1
8W-48 REAR WINDOW DEFOGGER

Fuse 7 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-48-2 Indicator Lamp . . . . . . . . . . . . . . . . . . . . . . 8W-48-2
Fuse 15 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-48-2 Instrument Cluster . . . . . . . . . . . . . . . . . . . 8W-48-2
Fuse Block . . . . . . . . . . . . . . . . . . . . . . . . . 8W-48-2 Rear Window Defogger . . . . . . . . . . . . . . . . 8W-48-2
G200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-48-2 Rear Window Defogger Relay . . . . . . . . . . . 8W-48-2
G302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-48-2 Rear Window Defogger Switch . . . . . . . . . . 8W-48-2
Illumination Lamp . . . . . . . . . . . . . . . . . . . 8W-48-2
8W - 48 - 2 8W-48 REAR WINDOW DEFOGGER TJ
BATT A0 (8W-10-6) RUN A22 (8W-10-8)

POWER FUSE
21 DISTRIBUTION BLOCK
FUSE CENTER FUSE (8W-11-2)
15 (8W-10-2) 7
40A 10A
28 (8W-10-14) (8W-11-7)
A4 27
F20 20VT/WT
12
BK/PK
F3 C106
S108
D2 D4 (8W-11-7)
REAR
WINDOW
DEFOGGER
RELAY
D8 D6 (PDC)
C15
12
BK/WT
F8 C106
S320
LHD RHD
C15 C81
14 H1 C323 1 C323 20
BK/WT LB/WT
17
FUSE 1 C326
BLOCK
FROM FUSE (8W-11-2) 1 C331
S206 17
(8W-11-4) 10A C15 12BK/WT
(8W-11-9)
2 C170
C15
E2 12
20 37
GY
OR A5 C202
F81 REAR
20 WINDOW
DB/RD C81
DEFOGGER 20
4 3 (HARD LB/WT
REAR TOP)
ILLUMINATION WINDOW
LAMP INDICATOR Z1
LAMP DEFOGGER 3 C1
(HARD 12
TOP) SWITCH BK REAR INSTRUMENT
(HARD WINDOW CLUSTER
TOP) DEFOGGER (8W-40-8)
S400 RELAY
(8W-15-11) CONTROL
1 2
Z1
6 C331
20 6 C326
BK
S309 REAR
S207 (8W-15-11) WINDOW
(8W-15-7) LHD RHD DEFOGGER
Z1 (8W-15-8) C80
SWITCH
16 20 5 C322
G5 C322 SENSE
BK DB/LG
4 C1
G200 G302
(8W-15-7) (8W-15-11)
(8W-15-8)
J998W-5 TJI04802
TJ 8W - 50 FRONT LIGHTING 8W - 50 - 1
8W-50 FRONT LIGHTING

Circuit Breaker . . . . . . . . . . . . . . . . . . . . 8W-50-2, 5 Instrument Cluster . . . . . . . . . . . 8W-50-2, 3, 4, 6, 8
Daytime Running Lamp Module . . . . . . . 8W-50-2, 8 Key-In Switch . . . . . . . . . . . . . . . . . . . . . . . 8W-50-3
Driver Door Ajar Switch . . . . . . . . . . . . . . . 8W-50-3 Left City Lamp . . . . . . . . . . . . . . . . . . . . . . 8W-50-4
Fog Lamp Relay No. 1 . . . . . . . . . . . . . . . . 8W-50-7 Left Fog Lamp . . . . . . . . . . . . . . . . . . . . . . 8W-50-7
Fog Lamp Relay No. 2 . . . . . . . . . . . 8W-50-2, 4, 6, 8 Left Front Park/Turn Signal Lamp . . . . . . . 8W-50-4
Front Fog Lamp Switch . . . . . . . . . . . . . . . 8W-50-7 Left Headlamp . . . . . . . . . . . . . . . . . . . . 8W-50-2, 8
Fuse 3 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-50-2, 6 Left Headlamp Leveling Motor . . . . . . . . . . 8W-50-5
Fuse 4 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-6 Left Side Marker Lamp . . . . . . . . . . . . . . . 8W-50-4
Fuse 16 (FB) . . . . . . . . . . . . . . . . . . . . . . 8W-50-2, 5 Powertrain Control Module . . . . . . . . . . . . . 8W-50-8
Fuse 25 (PDC) . . . . . . . . . . . . . . . . . . . . . . 8W-50-7 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . . . . 8W-50-6
Fuse Block . . . . . . . . . . . . . . . . . . . . . 8W-50-5, 6, 8 Right City Lamp . . . . . . . . . . . . . . . . . . . . . 8W-50-4
G100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-8 Right Fog Lamp . . . . . . . . . . . . . . . . . . . . . 8W-50-7
G102 . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-2, 4, 5, 7 Right Front Park/Turn Signal Lamp . . . . . . 8W-50-4
G103 . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-2, 4, 5, 7 Right Headlamp . . . . . . . . . . . . . . . . . . . 8W-50-2, 8
G200 . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-3, 5, 7 Right Headlamp Leveling Motor . . . . . . . . . 8W-50-5
G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-6 Right Side Marker Lamp . . . . . . . . . . . . . . 8W-50-4
Headlamp Dimmer Switch . . . . . . . 8W-50-2, 5, 6, 8 Turn Signal/Hazard Switch . . . . . . . . . . . . . 8W-50-4
Headlamp Leveling Switch . . . . . . . . . . . . . 8W-50-5 Vehicle Speed Sensor . . . . . . . . . . . . . . . . . 8W-50-8
Headlamp Switch . . . . . . . . . . 8W-50-2, 3, 4, 5, 6, 8
8W - 50 - 2 8W-50 FRONT LIGHTING TJ
BATT F34 BATT A3 DAYTIME

(8W-11-4) (8W-10-13)
3
FUSED
RUNNING
HEADLAMP B(+) LAMP
CIRCUIT SWITCH MODULE
OPTICAL
BREAKER 0 OFF HORN (8W-50-8)
24A 1 PARK FEED
2 HEAD
6
3 3 DOME
4 MAX
5 MIN L20
0 1 2 16
0 1 2
LG/WT
2 7
5 4 D8 C108
L2 L20
16 16
L20
1 9 LG LG/WT
16
A8 A2 LG/WT
C202
E1
18
L2 L20
TN
14 14
LG LG/WT
L2 2 4
A3 C202 16 HEADLAMP
LG DIMMER
E1 SWITCH
18 1 LOW
1 2 3
TN 2 HIGH
TO
3 FLASH
FUSE 1 3
16 (FB) L4 L3
TO (REAR FOG 14 14
FUSE LAMPS) VT/WT RD/OR
3 (FB) (8W-11-10)
E5 E4 C107
(8W-11-4) L3
L4
16 16
VT/WT RD/OR
DRL OTHER
S104 S105
(8W-50-8)
OTHER DRL
C110 1
5 4 L3
DIMMER SWITCH DAYTIME
S119 16
HIGH BEAM OUTPUT RUNNING
RD/OR
L4 HIGH BEAM LAMP
L4 L3 16RD/OR 16 INDICATOR DRIVER MODULE
16 VT/WT
VT/WT 4 (8W-50-8)
L3 G34 FOG
2 1 16 18 HIGH
RD/GY LAMP
LEFT RD/OR BEAM
1 2 INDICATOR
RELAY
HEADLAMP DRIVER NO. 2
3 RIGHT (EXCEPT
HEADLAMP D7 C108 1
Z1 G34 BUILT-UP
3 G34 16
20 16
-EXPORT)
Z1 RD/GY
BK RD/GY (8W-50-6)
18
S117 EXCEPT BUILT- BK BUILT-
UP-EXPORT UP-EXPORT
B5 C203
(8W-15-3)
Z1 5 C2
S150 INSTRUMENT
16 HIGH
(8W-15-5)
BK BEAM CLUSTER
INDICATOR (8W-40-9)
G102 G103 DRIVER
(8W-15-3) (8W-15-4)
J998W-5 (8W-15-5) TJI05002
TJ 8W-50 FRONT LIGHTING 8W - 50 - 3
INSTRUMENT
KEY-IN CLUSTER
IGNITION (8W-40-7)
SWITCH
SENSE
8 C1
G26
20
LB
FROM
S202
(8W-44-4) B3 C203
M2 G26
20 20
YL LB
3 5
HEADLAMP
SWITCH
0 OFF
1 PARK
0 1 2
2 HEAD
3 DOME
0 3
Z1 G16
16 20
BK BK/LB
RHD LHD
B4 C203
S207
(8W-15-8)
G16
20
Z1 Z1
BK/LB
16 16
BK BK
3
DRIVER DRIVER
Z1 DOOR DOOR
AJAR G16
16 AJAR 20
BK SWITCH
SENSE
SWITCH BK/LB
(8W-44-4)
G200
(8W-15-7) 1
(8W-15-8)
DRIVER KEY-IN
DOOR SWITCH
AJAR (8W-40-7)
SWITCH (8W-44-4)
SENSE
TJI05003 J998W-5
INSTRUMENT BATT F34 TURN

(8W-11-4)
CLUSTER SIGNAL/
LEFT (8W-40-9) HEADLAMP RIGHT
TURN HAZARD
TURN SWITCH
TURN 1 PARK SIGNAL SWITCH
SIGNAL
SIGNAL/ 1 (8W-52-3)
2 HEAD
10 C2 LEFT 0 2
TURN HAZARD 1 3 OFF
L61 L60
SIGNAL SWITCH 18
18 (8W-52-3)
GY 10 TN
INSTRUMENT
9
FOG CLUSTER
HEAD-
LAMP RIGHT (8W-40-9)
LAMP
RELAY TURN
SWITCH
SIGNAL
OUTPUT NO. 2 L7
(EXCEPT 18 6 C1
3
BUILT-UP BK/YL L60
EXPORT) 18
L61 L7
(8W-50-6) TN
18 18
GY BK/YL
B2 C203 B6 B1 C203
L7 18BK/YL
C107 LHD RHD
E3 E1 E2
C110 G1 C322 1 C322

3 1 2
S118
(8W-70-2)
S141
2 S142 TO
LEFT
L7 SIDE 2 S310
18 RIGHT (8W-70-2)
MARKER
BK/YL 1 L60 L7 SIDE
LAMP 18 18
1 MARKER
(EXCEPT BUILT- TN BK/YL
L61 LAMP
18
UP-EXPORT) L7
18
(EXCEPT BUILT-
GY L7 L7
S143 BK/YL UP-EXPORT)
18 18
1 2 LEFT BK/YL BK/YL
FRONT S144
PARK/ 1
3 TURN RIGHT
CITY RIGHT
SIGNAL 1 1 2
FRONT
Z1 LAMP
18
LAMP LEFT 2 PARK/
(EXCEPT BUILT- (BUILT-UP
BK CITY TURN
UP-EXPORT) -EXPORT)
2 LAMP 3 SIGNAL
FRONT EXCEPT FRONT (BUILT-UP Z1 LAMP
FOG LAMPS FOG LAMPS -EXPORT) 18 (EXCEPT BUILT-
BK UP-EXPORT)
S122 Z1
(8W-15-3) 20 FRONT EXCEPT FRONT
BK FOG LAMPS FOG LAMPS
Z1 Z1
18 18 S125
BK BK
S150 (8W-15-4)
(8W-15-5)
S117 Z1
(8W-15-3) Z1
Z1 18 18
16 BK BK
BK
G102 G103
(8W-15-3) (8W-15-4)
J998W-5 (8W-15-5) TJI05004
BUILT-UP-EXPORT
BATT A3 (8W-10-13)
HEADLAMP
CIRCUIT SWITCH
16
BREAKER 0 OFF
FUSE 24A 1 PARK
BLOCK 2 HEAD
FUSE (8W-11-2)
16
10A
(8W-11-10)
0 1 2
36 L2 2
16 L2
L22
LG 16
20
LG/DG LG
A8 C202
S330
(8W-11-10) L2
14
L22 LG
20
LG/DG
L22 20LG/DG 2
D13 C108 HEADLAMP HEADLAMP
C9 C204 SWITCH DIMMER
L22
20 OUTPUT SWITCH
LG/DG (8W-50-2)
9 C110
L22
20
LG/DG
S151
S138 (8W-11-10)
L13 L13 L13
20 20 20
BR/YL BR/YL BR/YL
14 C110
L13
L22 20
20 BR/YL
LG/DG 1 C170 L22 L22
20 20
2 5 LG/DG LG/DG
HEADLAMP 2 1 2 1
LEVELING LEFT RIGHT
SWITCH HEADLAMP HEADLAMP
M LEVELING M LEVELING
MOTOR MOTOR
4 3 3
Z1 Z1 Z1
20 20 18
BK BK BK
LHD RHD
S117 S150
S207 (8W-15-3) (8W-15-5)
(8W-15-7) Z1 Z1
Z1 16
16 18
BK BK
BK
G102 G103
G200 G200 (8W-15-3) (8W-15-5)
(8W-15-7) (8W-15-8)
TJI05005 J998W-5
FOG LAMPS
DIMMER HEADLAMP
SWITCH DIMMER
HIGH SWITCH BATT F34 (8W-11-4)
BEAM (8W-50-2)
OUTPUT HEADLAMP
3 SWITCH
0 OFF
L3 1 PARK
14 2 HEAD
RD/OR 0 2 3 DOME
1
4 MAX
E4 C107 5 MIN
3 4 5
(8W-50-2)
L3
16
RD/OR 9 1
S105
(8W-50-2)
L7 E1
L3 18 18
16 BK/YL TN
RD/OR
D7 C108
B6 C203 A3 C202
G34
16 G34
RD/GY 16
RD/GY
B5 C203 L7 E1
5 C2 18 18
HIGH INSTRUMENT BK/YL TN
G34 BEAM CLUSTER
16 INDICATOR (8W-40-9)
RD/GY DRIVER
1 3 3
FOG FUSE
LAMP BLOCK
RELAY FUSE (8W-11-2)
NO. 2 3
10A
2 4 (8W-11-4)
FUSE
23
BLOCK
Z1 FUSE (8W-11-2) L95
20 4 18 E2 E2
BK 10A DG/YL 20 20
(8W-11-5) OR OR
24 C1 C204 A4 C202
Z1
20 Z1 1
BK 20 L95 E2 FUSED PRNDL
BK 18 20 PANEL LAMP
DG/YL OR LAMPS (8W-44-5)
A DIMMER
S304 SWITCH
TO B C SIGNAL
(8W-15-9)
FOG
TO TO
LAMP Z1
16 FRONT S206
RELAY (8W-50-7)
BK FOG
NO. 1
(8W-50-7) LAMP
G300 SWITCH
(8W-50-7)
(8W-15-9)
J998W-5 TJI05006
FOG LAMPS
FROM FROM
C202 C204
(8W-50-6) (8W-50-6)
C B BATT A6 (8W-10-10)
FROM POWER
FOG E2 DISTRIBUTION
20 CENTER
LAMP OR
L95 A6
18 (8W-10-2)
RELAY FUSE
DG/YL 25
NO. 2 S206
(8W-50-6) (8W-11-4) 20A
(8W-10-16)
A A5
1 3
FRONT
FOG
LAMP F61
SWITCH 18
WT/OR
4 2 D6 C108
Z1
B13 C203
F61
20 18
BK L35
WT/OR
18
BR/WT
S207
(8W-15-7) 1 3
Z1 FOG
20 Z1
BK 16
LAMP
BK RELAY
NO. 1
2 5
G200
(8W-15-7) E10 C107
L39
18
LB
13 C110
S116
2 2
LEFT RIGHT
FOG FOG
1 LAMP 1 LAMP
S122 Z1
(8W-15-3) 18
BK
Z1
18
BK S125
(8W-15-4)
S117 Z1
(8W-15-3) 18
Z1 BK
16
BK G103
(8W-15-4)
G102
(8W-15-3)
TJI05007 J998W-5
DRL
ST-RUN A21 (8W-10-9) VEHICLE
VEHICLE SPEED
SPEED
FUSE SENSOR SENSOR
BLOCK SIGNAL (8W-30-10)
(8W-11-2)
3
FUSE HEADLAMP
11 FUSED
B(+) SWITCH G7
10A 20
OPTICAL (8W-50-2)
(8W-11-8) WT/OR
HORN
FEED
31 S135
7
F12 L20 G7
20 16 18
G7
RD/LG LG/WT WT/OR
20
WT/OR
F10 C106 A2 C202
B27 C2
L20 14LG/WT
F12 POWERTRAIN
20 L20 4 12 C103 VEHICLE CONTROL
RD/LG 16 FUSED HEADLAMP SPEED
LG/WT B(+) DIMMER G7 SENSOR MODULE
OPTICAL 20 SIGNAL (8W-30-10)
SWITCH
S102 D8 C108 HORN (8W-50-2) WT/OR
(8W-11-8) FEED
5 6 7
FUSED FUSED VEHICLE DAYTIME
IGNITION B(+) SPEED RUNNING
SWITCH OPTICAL SENSOR LAMP
OUTPUT HORN SIGNAL
(ST-RUN) FEED
MODULE
DIMMER DIMMER
SWITCH SWITCH HIGH
HIGH LOW BEAM
BEAM BEAM INDICATOR
OUTPUT OUTPUT DRIVER GROUND
1 10 4 8
DIMMER DIMMER HEADLAMP
G34
SWITCH SWITCH DIMMER
18
HIGH LOW SWITCH RD/GY Z1
BEAM BEAM (8W-50-2)
18
OUTPUT OUTPUT
BK
3 1
D7 C108
L3 L3 L4 L4
16 14 14 16 G34
RD/OR RD/OR VT/WT VT/WT 16
RD/GY
S106
(8W-15-2)
E4 E5 C107 G34 16RD/GY
L3 L4
B5 C203
1 Z1
16 16 12
RD/OR VT/WT FOG BK
HIGH
G34
BEAM LAMP
S105 S104 16
INDICATOR RELAY
(8W-50-2) RD/GY
DRIVER NO. 2
4 C110 5 C110 (8W-50-6)
5 C2
L3 INSTRUMENT
16 S119 HIGH
RD/OR BEAM CLUSTER
L3 16RD/OR INDICATOR (8W-40-9)
1 2 1 2 DRIVER G100
(8W-15-2)
LEFT RIGHT
HEADLAMP HEADLAMP
(8W-50-2) (8W-50-2)
J998W-5 TJI05008
TJ 8W - 51 REAR LIGHTING 8W - 51 - 1
8W-51 REAR LIGHTING

Back-Up Lamps . . . . . . . . . . . . . . . . . . . 8W-51-2, 3 G302 . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-51-4, 7, 8
Back-Up Lamp Switch . . . . . . . . . . . . . . 8W-51-2, 3 Headlamp Dimmer Switch . . . . . . . . . . . 8W-51-7, 8
Brake Lamp Switch . . . . . . . . . . . . . . . . 8W-51-4, 6 Headlamp Switch . . . . . . . . . . . . . . 8W-51-2, 3, 7, 8
Brake Shift Interlock Solenoid . . . . . . . . . . 8W-51-6 Left License Lamp . . . . . . . . . . . . . . . . . 8W-51-7, 8
Center High Mounted Stop Lamp . . . . . . 8W-51-4, 6 Left Rear Lamp Assembly . . . . . . 8W-51-2, 3, 4, 5, 6
Cigar Lighter/Accessory Relay . . . . . . . . . . 8W-51-6 Park/Neutral Position Switch . . . . . . . . . 8W-51-2, 3
Circuit Breaker . . . . . . . . . . . . . . . . . . . . 8W-51-7, 8 Powertrain Control Module . . . . . . . . . . . . . 8W-51-6
Controller Anti-Lock Brake . . . . . . . . . . . 8W-51-4, 6 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . . 8W-51-7, 8
Fog Lamp Illumination . . . . . . . . . . . . . . 8W-51-7, 8 Rear Fog Lamp . . . . . . . . . . . . . . . . . . . . 8W-51-7, 8
Fog Lamp Indicator . . . . . . . . . . . . . . . . 8W-51-7, 8 Rear Fog Lamp Relay . . . . . . . . . . . . . . . 8W-51-7, 8
Fuse 2 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-51-4, 6 Rear Fog Lamp Switch . . . . . . . . . . . . . . 8W-51-7, 8
Fuse 3 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-51-7, 8 Right License Lamp . . . . . . . . . . . . . . . . 8W-51-7, 8
Fuse 4 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-51-7, 8 Right Rear Lamp Assembly . . . . . 8W-51-2, 3, 4, 5, 6
Fuse 7 (FB) . . . . . . . . . . . . . . . . . . . . . . . 8W-51-2, 3 Tail/Stop/Turn Signal Lamps . . . . . . . . . 8W-51-2, 5
Fuse 16 (FB) . . . . . . . . . . . . . . . . . . . . . . 8W-51-7, 8 Tail/Turn Signal Lamps . . . . . . . . . . . . . . . 8W-51-3
Fuse Block . . . . . . . . . . . . . . . . 8W-51-2, 3, 4, 6, 7, 8 Turn Signal/Hazard Switch . . . . . . . 8W-51-2, 3, 5, 6
G200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-51-7, 8 Vehicle Speed Control Servo . . . . . . . . . . . . 8W-51-6
G300 . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-51-6, 7, 8
8W - 51 - 2 8W-51 REAR LIGHTING TJ
RUN A22 (8W-10-8) BATT F34 (8W-11-4)
FUSE HEADLAMP
BLOCK SWITCH
(8W-11-2) 0 OFF
FUSE 1 PARK
0 1 2
7 2 HEAD
10A (8W-50-4)
(8W-11-7)
9
27 TURN
F20
LEFT RIGHT
SIGNAL/
20 L7
18 TURN TURN HAZARD
VT/WT
BK/YL SIGNAL SIGNAL SWITCH
F3 C106 (8W-52-2)
9 3
S108 B6 C203
(8W-11-7)
10 C104 L7
18
F20
BK/YL
20
VT/WT
A/T M/T E1 C107
L7
4 C154 4 C154 18 L7
F20 F20 BK/YL 18
18 18 L63 L62
BK/YL
VT/WT VT/WT 18 18
1 B DG/RD BR/RD
1 C110
PARK/ BACK-UP
NEUTRAL LAMP L7
G1 C322
POSITION SWITCH 18
SWITCH BK/YL
3 A
L1 L1
18 18
VT/BK VT/BK TO
C154 L7 S118
2 C154 2 18 (8W-70-2)
L1 L1 BK/YL
20 20
VT/BK VT/BK
9 C104 S310
L1
(8W-70-2) G2 C322
20
VT/BK
G4 C322
F2 C106
S335
G3 C322
S311
L1 L7 L63 L63 L1 L7 L62
20 18 18 18 20 18 18
VT/BK BK/YL DG/RD DG/RD VT/BK BK/YL BR/RD
1 3 2 4 1 3 2
LEFT NOT RIGHT
TAIL/ REAR USED TAIL/ REAR
STOP/ LAMP STOP/ LAMP
BACK-UP BACK-UP
LAMP TURN ASSEMBLY LAMP TURN ASSEMBLY
SIGNAL SIGNAL
LAMP LAMP
J998W-5 TJI05102
TJ 8W-51 REAR LIGHTING 8W - 51 - 3
BUILT-UP-EXPORT
RUN A22 (8W-10-8) BATT F34 (8W-11-4)
FUSE HEADLAMP
BLOCK SWITCH
FUSE (8W-11-2) 0 OFF
7 1 PARK
0 1 2
10A 2 HEAD
(8W-11-7) (8W-50-4)
27 9
F3 C106 TURN
L7
SIGNAL/
S108 18 LEFT RIGHT
(8W-11-7) BK/YL TURN TURN HAZARD
10 C104 SIGNAL SIGNAL SWITCH
B6 C203 9 3 (8W-52-2)
F20
20
L7
VT/WT
18
A/T M/T BK/YL
4 C154 4 C154 E1 C107

F20 F20 L7
18 18 18
VT/WT VT/WT BK/YL
1 B L7
PARK/ BACK-UP 18 1 C110
BK/YL L63 L62
NEUTRAL LAMP 18 18
POSITION SWITCH TO DG/RD BR/RD
SWITCH S118
3 A (8W-70-2)
L1 L1 LHD RHD
18 18
VT/BK VT/BK G1 C322 1 C322
2 C154 2 C154 LHD RHD

L1 L1
20 20 L7
VT/BK VT/BK 18 G2 C322
BK/YL
2 C322
9 C104 S310
(8W-70-2)
L1 L7
20 18 LHD RHD
VT/BK BK/YL
F2 C106 G4 C322 4 C322
LHD RHD
G3 C322 L7
18
3 C322 L63
BK/YL
18
L62
DG/RD
18
S311 BR/RD
2 3 4 1 2 3 4 1
LEFT RIGHT
REAR REAR
TAIL/ TURN
BACK-UP
SIGNAL
LAMP BACK-UP TAIL/ TURN LAMP
LAMP STOP STOP SIGNAL
LAMP LAMP ASSEMBLY LAMP ASSEMBLY
LAMP LAMP
TJI05103 J998W-5
BATT A6 (8W-10-10)
FUSE
BLOCK
(8W-11-2)
FUSE
2
20A
(8W-11-4)
22
F32 CONTROLLER
18 BRAKE ANTI-LOCK
PK/DB LAMP
SWITCH
BRAKE
5
OUTPUT (8W-35-5)
BRAKE
LAMP
8 C1
SWITCH L50
(8W-51-6) 18
WT/TN
6
L50 18WT/TN L50

18
LHD EXCEPT WT/TN
BUILT-UP- BUILT-UP-
RHD EXPORT EXPORT D9 C108
7 C322 G7 C322 G7 C322
L50
18
EXCEPT L50
WT/TN
BUILT-UP- BUILT-UP- 18
EXPORT EXPORT WT/TN
S315
L50 L50
18 18
WT/TN WT/TN A
CENTER
3 HIGH TO
MOUNTED TURN
RIGHT STOP SIGNAL/
TAIL/STOP/TURN REAR LAMP HAZARD
SIGNAL LAMP LAMP SWITCH
ASSEMBLY (8W-51-5)
TAIL/STOP LAMP
Z1
18
BK
3 S309
(8W-15-11)
LEFT Z1
REAR 12
TAIL/STOP/TURN BK
SIGNAL LAMP LAMP
ASSEMBLY LHD RHD
TAIL/STOP LAMP
G5 C322 5 C322
BUILT-UP-EXPORT
G302
(8W-15-11)
J998W-5 TJI05104
FROM
C322
(8W-51-4)
A
L50
18
WT/TN
4 2
TURN
SIGNAL/
3 4
HAZARD
SWITCH
3 4 3 4 1 LEFT
2 RIGHT
3 NORMAL
4 HAZARD
1 2 1 2
9 1 10 3
L63 L62
18 18
DG/RD BR/RD
EXCEPT LHD EXCEPT LHD

BUILT-UP- BUILT-UP- BUILT-UP- BUILT-UP-
EXPORT EXPORT RHD EXPORT EXPORT RHD
G4 C322 G2 C322 2 C322

L63 G4 C322 4 C322 G2 C322
18
L62
DG/RD
18
S335 BR/RD
(8W-51-2)
L63 1
18
DG/RD
RIGHT
L63 TURN REAR
18 L63 L62 SIGNAL LAMP
2 DG/RD 18 18 LAMP ASSEMBLY
DG/RD BR/RD
LEFT (8W-51-3)
TAIL/
STOP/ REAR
TURN LAMP 4 2
SIGNAL ASSEMBLY RIGHT
LAMP (8W-51-2) NOT TAIL/
USED STOP/ REAR
TURN LAMP
1 SIGNAL ASSEMBLY
LAMP (8W-51-2)
LEFT
TURN REAR
SIGNAL LAMP
LAMP ASSEMBLY
(8W-51-3)
TJI05105 J998W-5
POWERTRAIN BATT A6 (8W-10-10)

SPEED CONTROL
CONTROL MODULE FUSE
ON/OFF BRAKE BLOCK
SWITCH SWITCH (8W-30-16)
FUSE (8W-11-2)
SENSE SENSE
BRAKE 2
C11 C3 C24 C3 SHIFT 20A
BRAKE (8W-11-4)
SWITCH INTERLOCK
V32 K29 SENSE SOLENOID
18 18 (8W-31-2) 22
1
YL/RD WT/PK
K29
20 F32
D1 D14
C108 WT/PK 18
PK/DB
V32 K29
20 20
YL/RD WT/PK
3 1 5
BRAKE
L50 18WT/TN
LAMP
SWITCH EXCEPT
LHD EXCEPT BUILT-UP BUILT-UP
BUILT-UP BUILT-UP -EXPORT -EXPORT
4 2 6 RHD -EXPORT -EXPORT
L50
G7 C322 S315
18 7 C322 G7 C322
WT/TN
Z1 L50
V30 20 18
20 BK CIGAR D9 C108 L50 WT/TN
DB/RD LIGHTER/ 18
L50 WT/TN CENTER
ACCESSORY 18 BRAKE
GROUND RELAY WT/TN LAMP HIGH
(8W-41-2) L50 SWITCH MOUNTED
E11 C107 5 18 OUTPUT
STOP
WT/TN
LAMP
LHD RHD 3 (8W-51-4)
Z1
V30 20 BRAKE RIGHT
20 BK L50 LAMP REAR
DB/RD 18 SWITCH LAMP
Z1 S304 WT/TN OUTPUT
(8W-15-10) ASSEMBLY
20 (8W-51-4)
BK Z1 3
16 8 C1
BK BRAKE CONTROLLER
LAMP ANTI-LOCK BRAKE LEFT
SWITCH BRAKE LAMP REAR
OUTPUT (8W-35-5) SWITCH LAMP
G300 OUTPUT
3 (8W-15-9) ASSEMBLY
(8W-15-10) (8W-51-4)
SPEED VEHICLE
CONTROL SPEED 2
BRAKE CONTROL BRAKE TURN
SWITCH SERVO LAMP SIGNAL/
OUTPUT SWITCH
(8W-30-16) HAZARD
OUTPUT
SWITCH
(8W-51-5)
J998W-5 TJI05106
LHD BUILT-UP-EXPORT
BATT A3 (8W-10-13) BATT F34 (8W-11-4)
HEADLAMP
CIRCUIT SWITCH
BREAKER 0 OFF
HEADLAMP 24A 1 PARK
HEAD-
DIMMER 2 HEAD
SWITCH 3 MAX
LAMP
(8W-50-2) 4 MIN
SWITCH
OUTPUT (8W-50-2)
0 1 2 0 1 2
(8W-50-4)
2
2 4 3
L2
L2 16
14 LG 1 9
LG E1 L7
A8 C202 18 18
TN BK/YL
L2 16LG A3 C202 B6 C203
16 3
FUSE L7
S330 BLOCK 18
(8W-11-10) FUSE FUSE (8W-11-2) BK/YL
L22 L22 L22 16 3
20 20 20 10A 10A
LG/DG LG/DG LG/DG (8W-11-10) (8W-11-4)
5 1 E1 C107 L7
HEADLAMP HEADLAMP REAR 36 23 18
SWITCH SWITCH FOG 1 C110 BK/YL
E2
FUSED FUSED LAMP 20 E2
OUTPUT OUTPUT OR 20 L7
G1 C322
RELAY
OR 18
REAR
BK/YL L7
FOG REAR TO 18
LAMP FOG PRNDL A4 C202 BK/YL
RELAY LAMP
CONTROL FEED GROUND LAMP S206
(8W-44-5) (8W-11-4) TO S310
2 4 3
S118 (8W-70-2)
L95 L38 (8W-70-2)
18 20 G8 C322 L38 2 C329
DG/YL BR/WT 20
L38 20BR/WT BR/WT
S317
C1 C8 C204 Z1 1 C329
2 3 20 L7 L7
L38
REAR BK 18 18
18
FOG BR/WT BK/YL BK/YL
FOG
LAMP LAMP 1 1 1
INDICATOR SWITCH REAR LEFT RIGHT
FOG LICENSE LICENSE
Z1 20BK
LAMP LAMP LAMP
FOG 2 2 2
24
LAMP
ILLUMINATION FUSE S316
BLOCK 3 C329
FUSE (8W-11-2) Z1
1 4 4 S304 20
Z1 E2 10A (8W-15-9) BK
20 20 (8W-11-5)
BK OR S309
(8W-15-11)
S207 Z1 Z1
16 12
(8W-15-7)
BK BK
Z1 16BK G5 C322
G200 G300 G302
(8W-15-7) (8W-15-9) (8W-15-11)
TJI05107 J998W-5
RHD BUILT-UP-EXPORT
BATT A3 (8W-10-13) BATT F34 (8W-11-4)
HEADLAMP
CIRCUIT SWITCH
BREAKER 0 OFF
HEADLAMP 24A 1 PARK
HEAD-
DIMMER 2 HEAD
SWITCH 3 MAX
LAMP
(8W-50-2) 4 MIN
SWITCH
OUTPUT (8W-50-2)
0 1 2 0 1 2
(8W-50-4)
2
2 4 3
L2
L2 16
14 LG 1 9
LG E1 L7
A8 C202 18 18
TN BK/YL
L2 16LG
A3 C202 B6 C203
16 3
S330 FUSE L7
(8W-11-10) BLOCK 18
L22 L22 L22 FUSE FUSE (8W-11-2) BK/YL
20 20 20 16 3
LG/DG LG/DG LG/DG 10A 10A
5 1 (8W-11-10) (8W-11-4)
REAR E1 C107 L7
HEADLAMP HEADLAMP
SWITCH SWITCH FOG 36 23 18
FUSED FUSED 1 C110 BK/YL
LAMP E2
OUTPUT OUTPUT E2
RELAY 20
L7 1 C322
OR 20
OR 18
REAR BK/YL L7
FOG REAR TO 18
LAMP FOG PRNDL A4 C202 BK/YL
RELAY LAMP
CONTROL FEED GROUND LAMP S206
(8W-44-5) TO
2 4 3 (8W-11-4)
S118 S310
(8W-70-2) (8W-70-2)
L95 L38
18 20 8 C322 L38 2 C329
DG/YL BR/WT 20
L38 20BR/WT BR/WT
S317
C1 C8 C204 Z1 1 C329
2 3 20 L7 L7
L38
REAR BK 18 18
18
FOG BR/WT BK/YL BK/YL
FOG
LAMP LAMP 1 1 1
INDICATOR SWITCH REAR LEFT RIGHT
FOG LICENSE LICENSE
Z1 20BK
LAMP LAMP LAMP
FOG 2 2 2
24
LAMP
ILLUMINATION FUSE S316
BLOCK 3 C329
FUSE (8W-11-2) Z1
1 4 4 20
Z1 E2 10A BK
20 20 (8W-11-5)
BK OR S309
(8W-15-11)
S207 Z1
12
(8W-15-8)
BK
Z1 16BK 5 C322
G200 G300 G302
(8W-15-8) (8W-15-10) (8W-15-11)
J998W-5 TJI05108
TJ 8W - 52 TURN SIGNALS 8W - 52 - 1
8W-52 TURN SIGNALS

Combination Flasher . . . . . . . . . . . . . . . . . 8W-52-2 Left Repeater Lamp . . . . . . . . . . . . . . . . . . 8W-52-3
Fuse 9 (PDC) . . . . . . . . . . . . . . . . . . . . . . . 8W-52-2 Left Side Marker Lamp . . . . . . . . . . . . . . . 8W-52-3
Fuse Block . . . . . . . . . . . . . . . . . . . . . . . . . 8W-52-2 Right Front Park/Turn Signal Lamp . . . . . . 8W-52-3
G102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-52-3 Right Front Turn Signal Lamp . . . . . . . . . 8W-52-3
G103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-52-3 Right Rear Lamp Assembly . . . . . . . . . . . . 8W-52-2
G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-52-2 Right Repeater Lamp . . . . . . . . . . . . . . . . . 8W-52-3
Instrument Cluster . . . . . . . . . . . . . . . . . . . 8W-52-3 Right Side Marker Lamp . . . . . . . . . . . . . . 8W-52-3
Left Front Park/Turn Signal Lamp . . . . . . . 8W-52-3 Tail/Stop/Turn Signal Lamp . . . . . . . . . . . . 8W-52-2
Left Front Turn Signal Lamp . . . . . . . . . . . 8W-52-3 Turn Signal/Hazard Switch . . . . . . . . . . . 8W-52-2, 3
Left Rear Lamp Assembly . . . . . . . . . . . . . . 8W-52-2
8W - 52 - 2 8W-52 TURN SIGNALS TJ
RUN-ACC A31 (8W-10-9) BATT A0 (8W-10-6)

FUSE POWER
FUSE
(8W-11-2)
FUSE CENTER
13 9 (8W-10-2)
10A 20A
(8W-11-9) (8W-10-13) COMBINATION
15
FLASHER
33 COMBINATION COMBINATION
FLASHER FLASHER
L9 INPUT OUTPUT GROUND
16
BK/WT 6 2 4
Z1
20
BK
L5 L55 L32
20 D11 C108 16 16 S304
BK/GY RD/WT PK (8W-15-9)
L9 Z1 (8W-15-10)
16 16
BK/WT BK
G300
(8W-15-9)
5 6 11 4 2 (8W-15-10)
TURN
SIGNAL/
3 4 3 4
HAZARD
SWITCH
3 4 3 4 1 LEFT
2 RIGHT
3 NORMAL
4 HAZARD
1 2 1 2
9 1 10 3
L63 L62
EXCEPT LHD 18 EXCEPT LHD 18
BUILT-UP- BUILT-UP- DG/RD BUILT-UP- BUILT-UP- BR/RD
EXPORT EXPORT RHD EXPORT EXPORT RHD
G4 C322 G2 C322 2 C322

L63 G4 C322 4 C322 G2 C322
18
L62
DG/RD
18
S335 BR/RD
(8W-51-2) 1
L63 L62 RIGHT
L63 18 18
18 L63 TURN REAR
DG/RD BR/RD
DG/RD 18 SIGNAL LAMP
DG/RD LAMP ASSEMBLY
2 (8W-51-3)
1 4 2
LEFT
TAIL/
REAR LEFT NOT RIGHT
STOP/ TAIL/
LAMP TURN REAR USED STOP/ REAR
TURN
SIGNAL ASSEMBLY SIGNAL LAMP TURN LAMP
LAMP LAMP ASSEMBLY SIGNAL ASSEMBLY
(8W-51-2)
(8W-51-3) LAMP (8W-51-2)
J998W-5 TJI05202
TJ 8W-52 TURN SIGNALS 8W - 52 - 3
5 6 11 4 2
TURN
3 4 3 4 SIGNAL/
HAZARD
SWITCH
3 4 3 4
1 LEFT
2 RIGHT
3 NORMAL
4 HAZARD
1 2 1 2
9 1 10 3
L60 L61
18 18
TN GY
B1 B2 C203
L60 6 C1 10 C2 L61
18 18
TN RIGHT LEFT INSTRUMENT GY
TURN TURN CLUSTER
SIGNAL SIGNAL (8W-40-9)
E2 E3 C107
2 3 C110
L60 L61
18 EXCEPT 18 EXCEPT
BUILT- TN BUILT- GY BUILT-
BUILT-
UP-EXPORT UP-EXPORT UP-EXPORT
UP-EXPORT
S142 S141
2 2 LEFT
S142 RIGHT S141
SIDE SIDE
1
MARKER MARKER
1 LEFT
RIGHT 1 LAMP 1 LAMP
REPEATER
REPEATER LAMP 1 S143
S144 2 LEFT
2 LAMP 1 RIGHT L60 (8W-50-4)
18
(8W-50-4) FRONT L61 L7
FRONT L7 Z1 TURN 18 18
TN 18
TURN 18 3 SIGNAL
GY BK/YL
Z1 BK/YL
SIGNAL BK LEFT
18 3 LAMP 1 2
BK LAMP RIGHT FRONT
1 2
FRONT S122
(8W-15-3)
PARK/
S125 PARK/ TURN
(8W-15-5) TURN 3 SIGNAL
Z1
Z1 SIGNAL 18
18
3 LAMP
LAMP BK FRONT
BK FRONT OTHER FOG LAMPS
FOG LAMPS OTHER
S122
S150 S125 (8W-15-3)
(8W-15-5) (8W-15-4)
S117
(8W-15-3) Z1
Z1 18
18 Z1
BK
BK 16
BK
G103
(8W-15-4) G102
(8W-15-5) (8W-15-3)
TJI05203 J998W-5
TJ 8W - 53 WIPERS 8W - 53 - 1
8W-53 WIPERS
Fuse 3 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-53-4 Internal Delay Relay . . . . . . . . . . . . . . . . . . 8W-53-3
Fuse 6 (FB) . . . . . . . . . . . . . . . . . . . . . . . . . 8W-53-4 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . . . . 8W-53-4
Fuse 14 (FB) . . . . . . . . . . . . . . . . . . . . . . 8W-53-2, 3 Rear Washer Pump . . . . . . . . . . . . . . . . . . . 8W-53-4
Fuse Block . . . . . . . . . . . . . . . . . . . . . 8W-53-2, 3, 4 Rear Wiper Motor . . . . . . . . . . . . . . . . . . . . 8W-53-4
G102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-53-2, 3 Rear Wiper/Washer Switch . . . . . . . . . . . . . 8W-53-4
G200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-53-4 Windshield Washer Pump . . . . . . . . . . . . 8W-53-2, 3
G300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-53-2, 3 Windshield Wiper Motor . . . . . . . . . . . . . 8W-53-2, 3
G302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-53-4 Windshield Wiper Switch . . . . . . . . . . . . 8W-53-2, 3
Headlamp Switch . . . . . . . . . . . . . . . . . . . . 8W-53-4
8W - 53 - 2 8W-53 WIPERS TJ
STANDARD
RUN-ACC A31 (8W-10-9)
FUSE
BLOCK
(8W-11-2)
FUSE
14
20A
(8W-11-9)
34
V6
18
PK/BK
S306
V6
18
PK/BK
5
WINDSHIELD
WIPER
SWITCH
0 OFF
0 2 0 2 0 3 1 LOW
1 1 2 HIGH
3 WASH
2 4 6 3
V10
18
BR
V6 V5 V3 V4
18 18 18 18
PK/BK DG/YL BR/WT RD/YL E8 C107
V10
18
1 2 5 6
BR
WINDSHIELD
4 WIPER 8 C110
3 MOTOR
M V10
1 PARK
18
2 RUN
1 2 BR
3 LOW
4 HIGH A
WINDSHIELD
WASHER
M PUMP
4
Z1 B
18
BK Z1
18
S304 BK
(8W-15-9)
(8W-15-10) S117
Z1 (8W-15-3)
16
Z1
BK
16
BK
G300
(8W-15-9)
(8W-15-10)
G102
(8W-15-3)
J998W-5 TJI05302
TJ 8W-53 WIPERS 8W - 53 - 3
INTERMITTENT
RUN-ACC A31 (8W-10-9)
FUSE
BLOCK
(8W-11-2)
FUSE
14
20A
(8W-11-9)
34
V6
18
PK/BK
S306
5
WINDSHIELD
WIPER
5 SWITCH
0 OFF
0 3 3 1 DELAY
0
2 LOW
1 2 1 2
6 3 HIGH
4 WASH
5 MIN
DELAY INTERNAL
6 MAX
LOGIC AND DELAY
RELAY RELAY
CONTROL
0 4
1 2 4 6 3
V5 V3 V4 V10
18 18 18 18
DG/YL BR/WT RD/YL BR
V6
18 E8 C107
PK/BK
8 C110
1 2 5 6
WINDSHIELD V10
4 18
3
WIPER BR
M MOTOR A
1 PARK
1 2 2 RUN WINDSHIELD
3 LOW WASHER
4 HIGH M PUMP
B
4
Z1
Z1 Z1 18
20 18 BK
BK BK
S117
S304 (8W-15-3)
(8W-15-9)
Z1 (8W-15-10) Z1
16 16
BK BK
G300 G102
(8W-15-9) (8W-15-3)
TJI05303 (8W-15-10) J998W-5
8W - 53 - 4 8W-53 WIPERS TJ
HARD TOP
BATT F34 (8W-11-4) RUN A22 (8W-10-8)
HEADLAMP REAR FUSE
SWITCH WIPER BLOCK
0 OFF MOTOR FUSE
(8W-11-2)
1 PARK M 1 PARK
0 2 HEAD 6
5 4 3 2 1 2 RUN 20A
3 DOME 1 2
4 MAX (8W-11-6)
1 5 MIN
E1 (8W-50-2) 26
3 1 2
18
V23
TN
18
A3 C202 V13 V23 Z1 BR/PK
3 18 18 16 LHD RHD
FUSE BK/LG BR/PK BK
BLOCK H4 C323 4 C323
FUSE (8W-11-2)
3 C331
3 V13 5 C326
10A 18
(8W-11-4) BR/LG 5 C331
3 C326 S401 S400
23 (8W-15-11)
LHD RHD V21 Z1
18 12
E2 E2 BR/PK BK
20 20 H5 C323 5 C323 4 C331
OR OR 6
4 6 C326
A4 C202 TO V23 Z1
E2 PRNDL 18 12
V13 BR/PK BK
20 LAMP
18 LHD RHD
OR (8W-44-5) S309
BR/LG
(8W-15-11)
G10 C322 10 C322
S206 C2 C204
(8W-11-4) V23 V23 Z1 Z1
18 18 18 12
E2 V13 BR/PK BR/PK BK BK
20 18 LHD RHD
OR BR/LG
C6 C204 5 C322
3 4 5 G5 C322
REAR
1 1 WIPER/
2 0 2 0
ILLUMINATION WASHER
Z1
LAMP SWITCH 12
0 OFF BK
1 WIPE
2 WASH G302
(8W-15-11)
1 2
B
V20 REAR
Z1 18 WASHER
18 VT/OR M PUMP
BK/WT
B9 C203
S207 V20
A
(8W-15-7) 18
(8W-15-8) VT/OR V20
Z1
16 18
LHD RHD VT/OR
BK
H6 C323 6 C323
G200
(8W-15-7)
J998W-5 (8W-15-8) TJI05304
TJ 8W - 70 SPLICE INFORMATION 8W - 70 - 1
8W-70 SPLICE INFORMATION

S101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-11 S141 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-4
S102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-8 S142 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-4
S103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-42-4 S143 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-4
S104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-8 S144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-4
S105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-2, 8 S146 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-17
S106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-2 S147 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-70-3
S107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-11 S150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-5
S108 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-7 S151 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-10
S109 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-2 S202 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-4
S110 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-17 S204 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-15
S112 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-17 S206 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-4
S114 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-17 S207 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-7, 8
S115 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-16 S301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-4
S116 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-16 S302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-14
S117 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-3 S303 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-14
S118 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-70-2 S304 . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-9, 10
S119 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-2, 8 S306 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-9
S122 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-3 S307 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-9
S123 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-70-4 S309 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-11
S124 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-11 S310 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-70-2
S125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-4, 5 S311 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-51-2, 3
S126 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-12 S313 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-15
S127 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-70-3 S314 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-44-2
S128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-12 S315 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-51-4, 6
S129 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-70-4 S316 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-11
S130 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-6 S317 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-51-7, 8
S131 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-8 S320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-14
S132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-6 S330 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-10
S133 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-70-3 S331 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-8
S134 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-6 S332 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-10
S135 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-30-10 S335 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-51-2
S136 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-10-6 S400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-15-11
S138 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-50-5 S401 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-11-6
8W - 70 - 2 8W-70 SPLICE INFORMATION TJ
LEFT RADIO HEADLAMP

LICENSE (8W-47-2) SWITCH
LAMP (8W-50-4)
(BUILT-UP
1 -EXPORT) 4 C1 9
(8W-51-7)
(8W-51-8)
L7 L7
RIGHT 18 18
LICENSE BK/YL BK/YL
LAMP
(BUILT-UP
1 -EXPORT)
(8W-51-7) B6 C203
(8W-51-8) LEFT RIGHT
REAR REAR
L7 L7 LAMP LAMP
18 18 ASSEMBLY ASSEMBLY
BK/YL BK/YL
(8W-51-2) (8W-51-2)
(8W-51-3) 3 (8W-51-3)
S317 3 4
4
2 C329
L7
18
L7 L7 L7
BK/YL
18 18 18
BK/YL BK/YL BK/YL
S310 3
LEFT RIGHT FOG
FRONT FRONT LAMP
PARK/ PARK/ RELAY
TURN TURN NO. 2
SIGNAL SIGNAL L7 (EXCEPT
2 2 18
LAMP LAMP BK/YL BUILT-UP
(EXCEPT (EXCEPT -EXPORT)
BUILT-UP- BUILT-UP- LHD RHD (8W-50-6)
L7
EXPORT) EXPORT) G1 C322 1 C322 18
(8W-50-4) (8W-50-4) BK/YL
LEFT RIGHT L7 RIGHT

18 CITY
SIDE SIDE BK/YL
MARKER MARKER LAMP
LAMP LAMP (BUILT-UP
E1 C107 -EXPORT)
1 (EXCEPT 1 (EXCEPT LEFT 1
(8W-50-4)
BUILT-UP- BUILT-UP- CITY
L7 L7 L7 L7 L7
18 18
EXPORT) 18 18
EXPORT) 18 LAMP
BK/YL BK/YL (8W-50-4) BK/YL BK/YL (8W-50-4) BK/YL (BUILT-UP
1 C110 1 -EXPORT)
S143 S144 (8W-50-4)
L7 L7 L7 L7 L7
18 18 18 18 18
BK/YL BK/YL BK/YL BK/YL BK/YL
S118
BUILT-UP-EXPORT
J998W-5 TJI07002
TJ 8W-70 SPLICE INFORMATION 8W - 70 - 3
OXYGEN MANIFOLD INTAKE

SENSOR ABSOLUTE AIR
1/1 PRESSURE TEMPERATURE
UPSTREAM SENSOR SENSOR
3 (8W-30-9) 1 (8W-30-7) 2 (8W-30-7)
(8W-30-8) (8W-30-8)
ENGINE
COOLANT
TEMPERATURE
K167 K167 K167
SENSOR
20 20 20 2 (8W-30-7)
BR/YL BR/YL BR/YL (8W-30-8)
K167 BATTERY
20 TEMPERATURE
BR/YL SENSOR
(8W-30-10)
S127 2
K167 K167 LHD RHD
20 20
BR/YL BR/YL K167 K167 K167 K167
20 20 20 18
2 1
BR/YL BR/YL BR/YL BR/YL
CRANKSHAFT THROTTLE
POSITION POSITION 3
SENSOR SENSOR ENGINE
(8W-30-4) (8W-30-10) OIL
PRESSURE
SENSOR CLOCKSPRING
OXYGEN (8W-30-15)
FUEL SENSOR (2.5L)
PUMP (8W-30-7)
1/2
MODULE DOWNSTREAM
(8W-30-3) 3 C2
3 (8W-30-9)
4 K167
20
VEHICLE BR/YL
SPEED SPEED
SENSOR CONTROL OTHER
(8W-30-10)
K167 K167
20 20 2 D3 C108 D3 C108
BR/YL BR/YL K167 NOT
20 USED
K167
20 BR/YL
BR/YL
S147
S133
K167 K167
20 20 K167
BR/YL BR/YL 20
BR/YL
2 8 C103
K167 K167 CAMSHAFT
20 18
BR/YL BR/YL POSITION
SENSOR
(8W-30-4)
3 A4 C1
ENGINE POWERTRAIN
OIL CONTROL
PRESSURE MODULE
SENSOR (8W-30-3)
(4.0)
(8W-30-8)
TJI07003 J998W-5
8W - 70 - 4 8W-70 SPLICE INFORMATION TJ
POWERTRAIN VEHICLE ENGINE

CONTROL SPEED OIL
MODULE SENSOR PRESSURE
(8W-30-7) (8W-30-10) SENSOR
(8W-30-7)
B31 C2 1 1
(8W-30-8)
K6 K6 K6
18 20 20
VT/OR VT/OR VT/OR
S123
MANIFOLD
ABSOLUTE
PRESSURE
SENSOR
3 (8W-30-7)
(8W-30-8)
POWERTRAIN CAMSHAFT CRANKSHAFT
CONTROL POSITION POSITION THROTTLE
MODULE SENSOR SENSOR POSITION
(8W-30-4) (8W-30-4) (8W-30-4) SENSOR
(8W-30-10)
A17 C1 3 3
3
K7 K7 K7 K7 K7
18 20 20 20 20
OR OR OR OR OR
S129
PARK/
NEUTRAL
POWERTRAIN POSITION
CONTROL SWITCH
MODULE 2 (8W-21-2)
(8W-30-12)
D11 T41
A6 C1 20
ENGINE BR/LB
1 C154
STARTER
Z1 MANUAL Z1
MOTOR 20 20
TRANSMISSION
RELAY BK BK
3 C154 JUMPER
D13 (IN PDC)
(8W-21-2) 3 C154 S132
(8W-15-6)
T41
T41 20 T41 T41 Z1
18 BR/LB 20 20 14
BR/LB BR/LB BR/LB BK
5 C104
A/T M/T
T41 T41
20 20
BR/LB BR/LB
G105
S134 (8W-15-6)
J998W-5 TJI07004
TJ 8W - 80 CONNECTOR PIN-OUTS 8W - 80 - 1
8W-80 CONNECTOR PIN-OUTS

A/C Compressor Clutch . . . . . . . . . . . . . . . . 8W-80-4 C322 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-12
A/C Heater Controls . . . . . . . . . . . . . . . . . . 8W-80-4 C323 . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-12, 13
A/C High Pressure Switch . . . . . . . . . . . . . 8W-80-4 C325 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-13
A/C Low Pressure Switch . . . . . . . . . . . . . . 8W-80-5 C326 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-13
ABS Diode . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-5 C329 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-14
ABS Pump Motor . . . . . . . . . . . . . . . . . . . . 8W-80-5 C330 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-14
Airbag Control Module . . . . . . . . . . . . . . . . 8W-80-5 C331 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-14
Back-Up Lamp Switch . . . . . . . . . . . . . . . . 8W-80-5 Camshaft Position Sensor . . . . . . . . . . . . . 8W-80-14
Battery Temperature Sensor . . . . . . . . . . . . 8W-80-6 Cigar Lighter/Accessory Relay . . . . . . . . . 8W-80-15
Brake Lamp Switch . . . . . . . . . . . . . . . . . . 8W-80-6 Cigar Lighter/Power Outlet . . . . . . . . . . . . 8W-80-15
Brake Shift Interlock Solenoid . . . . . . . . . . 8W-80-6 Clocksprings . . . . . . . . . . . . . . . . . . . . . . . 8W-80-15
Brake Warning Indicator Switch . . . . . . . . . 8W-80-6 Clutch Pedal Position Switch . . . . . . . . . . 8W-80-15
C103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-6 Combination Flasher . . . . . . . . . . . . . . . . . 8W-80-15
C104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-7 Controller Anti-Lock Brake . . . . . . . . . . . . 8W-80-16
C106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-7 Crankshaft Position Sensor . . . . . . . . . . . . 8W-80-16
C107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-8 Data Link Connector . . . . . . . . . . . . . . . . . 8W-80-17
C108 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-8 Daytime Running Lamp Module . . . . . . . . 8W-80-17
C110 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-9 Driver Door Ajar Switch . . . . . . . . . . . . . . 8W-80-18
C154 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-9 Duty Cycle Evap/Purge Solenoid . . . . . . . . 8W-80-18
C170 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-10 Engine Coolant Temperature Sensor . . . . . 8W-80-18
C180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-10 Engine Oil Pressure Sensor . . . . . . . . . . . 8W-80-18
C202 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-10 Fog Lamp Relay No. 1 . . . . . . . . . . . . . . . 8W-80-19
C203 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-11 Fog Lamp Relay No. 2 . . . . . . . . . . . . . . . 8W-80-19
C204 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-11 Front Fog Lamp Switch . . . . . . . . . . . . . . 8W-80-19
8W - 80 - 2 8W - 80 CONNECTOR PIN-OUTS TJ

Fuel Injector No. 1 . . . . . . . . . . . . . . . . . . 8W-80-19 Left Fog Lamp . . . . . . . . . . . . . . . . . . . . . 8W-80-25
Fuel Injector No. 2 . . . . . . . . . . . . . . . . . . 8W-80-20 Left Front Park/Turn Signal Lamp . . . . . . 8W-80-25
Fuel Injector No. 3 . . . . . . . . . . . . . . . . . . 8W-80-20 Left Front Speaker . . . . . . . . . . . . . . . . . . 8W-80-25
Fuel Injector No. 4 . . . . . . . . . . . . . . . 8W-80-20, 21 Left Front Turn Signal Lamp . . . . . . . . . . 8W-80-26
Fuel Injector No. 5 . . . . . . . . . . . . . . . . . . 8W-80-21 Left Front Wheel Speed Sensor . . . . . . . . . 8W-80-26
Fuel Injector No. 6 . . . . . . . . . . . . . . . . . . 8W-80-21 Left Headlamp . . . . . . . . . . . . . . . . . . . . . 8W-80-26
Fuel Pump Module . . . . . . . . . . . . . . . . . . 8W-80-21 Left Headlamp Leveling Motor . . . . . . . . . 8W-80-26
G-Switch . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-21 Left License Lamp . . . . . . . . . . . . . . . . . . 8W-80-26
Generator . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-21 Left Rear Lamp Assembly . . . . . . . . . . . . . 8W-80-27
Headlamp Dimmer Switch . . . . . . . . . . . . 8W-80-22 Left Rear Speaker . . . . . . . . . . . . . . . . . . . 8W-80-27
Headlamp Leveling Switch . . . . . . . . . . . . 8W-80-50 Left Rear Wheel Speed Sensor . . . . . . . . . 8W-80-27
Headlamp Switch . . . . . . . . . . . . . . . . . . . 8W-80-22 Left Repeater Lamp . . . . . . . . . . . . . . . . . 8W-80-27
High Note Horn . . . . . . . . . . . . . . . . . . . . 8W-80-22 Left Side Marker Lamp . . . . . . . . . . . . . . . 8W-80-27
HVAC Unit . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-22 Low Note Horn . . . . . . . . . . . . . . . . . . . . . 8W-80-27
Hydraulic Control Unit . . . . . . . . . . . . . . . 8W-80-23 Manifold Absolute Pressure Sensor . . . . . . 8W-80-28
Idle Air Control Motor . . . . . . . . . . . . . . . . 8W-80-23 Oxygen Sensor 1/1 Upstream . . . . . . . . . . 8W-80-28
Ignition Coil . . . . . . . . . . . . . . . . . . . . . . . 8W-80-23 Oxygen Sensor 1/2 Downstream . . . . . . . . 8W-80-28
Ignition Switch . . . . . . . . . . . . . . . . . . . . . 8W-80-23 Park/Neutral Position Switch . . . . . . . . . . 8W-80-28
Instrument Cluster . . . . . . . . . . . . . . . . . . 8W-80-24 Passenger Airbag . . . . . . . . . . . . . . . . . . . 8W-80-28
Intake Air Temperature Sensor . . . . . . . . . 8W-80-24 Passanger Airbag On/Off Switches . . . . . . 8W-80-29
Key-In Switch . . . . . . . . . . . . . . . . . . . . . . 8W-80-24 Passenger Door Ajar Switch . . . . . . . . . . . 8W-80-29
Leak Detection Pump . . . . . . . . . . . . . . . . 8W-80-25 Power Steering Pressure Switch . . . . . . . . 8W-80-29
Left City Lamp . . . . . . . . . . . . . . . . . . . . . 8W-80-25 Powertrain Control Modules . . . . . 8W-80-30, 31, 32
Left Courtesy Lamp . . . . . . . . . . . . . . . . . 8W-80-25 PRNDL Lamp . . . . . . . . . . . . . . . . . . . . . . 8W-80-32
TJ 8W - 80 CONNECTOR PIN-OUTS 8W - 80 - 3

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8W-80-33 Right Rear Lamp Assemby . . . . . . . . . . . . 8W-80-36
Rear Fog Lamp . . . . . . . . . . . . . . . . . . . . . 8W-80-33 Right Rear Speaker . . . . . . . . . . . . . . . . . . 8W-80-36
Rear Fog Lamp Relay . . . . . . . . . . . . . . . . 8W-80-33 Right Rear Wheel Speed Sensor . . . . . . . . 8W-80-37
Rear Fog Lamp Switch . . . . . . . . . . . . . . . 8W-80-33 Right Repeater Lamp . . . . . . . . . . . . . . . . 8W-80-37
Rear Washer Pump . . . . . . . . . . . . . . . . . . 8W-80-34 Right Side Marker Lamp . . . . . . . . . . . . . 8W-80-37
Rear Window Defogger Switch . . . . . . . . . 8W-80-34 Seatbelt Switch . . . . . . . . . . . . . . . . . . . . . 8W-80-37
Rear Wiper Motor . . . . . . . . . . . . . . . . . . . 8W-80-34 Sentry Key Immobilizer Module . . . . . . . . 8W-80-37
Rear Wiper/Washer Switch . . . . . . . . . . . . 8W-80-34 Sound Bar Dome Lamp . . . . . . . . . . . . . . . 8W-80-37
Right City Lamp . . . . . . . . . . . . . . . . . . . . 8W-80-35 Throttle Position Sensor . . . . . . . . . . . . . . 8W-80-38
Right Courtesy Lamp . . . . . . . . . . . . . . . . 8W-80-35 Torque Converter Clutch Solenoid . . . . . . . 8W-80-38
Right Fog Lamp . . . . . . . . . . . . . . . . . . . . 8W-80-35 Transfer Case Switch . . . . . . . . . . . . . . . . 8W-80-38
Right Front Park/Turn Signal Lamp . . . . . 8W-80-35 Turn Signal/Hazard Switch . . . . . . . . . . . . 8W-80-38
Right Front Speaker . . . . . . . . . . . . . . . . . 8W-80-35 Underhood Lamp . . . . . . . . . . . . . . . . . . . 8W-80-38
Right Front Turn Signal Lamp . . . . . . . . 8W-80-35 Vehicle Speed Control Servo . . . . . . . . . . . 8W-80-39
Right Front Wheel Speed Sensor . . . . . . . 8W-80-36 Vehicle Speed Sensor . . . . . . . . . . . . . . . . 8W-80-39
Right Headlamp . . . . . . . . . . . . . . . . . . . . 8W-80-36 Windshield Washer Pump . . . . . . . . . . . . . 8W-80-39
Right Headlamp Leveling Motor . . . . . . . . 8W-80-36 Windshield Wiper Motor . . . . . . . . . . . . . . 8W-80-39
Right License Lamp . . . . . . . . . . . . . . . . . 8W-80-36 Windshield Wiper Switch . . . . . . . . . . . . . 8W-80-39
8W - 80 - 4 8W-80 CONNECTOR PIN-OUTS TJ
BLACK
1 2
CAV CIRCUIT FUNCTION

1 C3 20DB/BK A/C COMPRESSOR CLUTCH RELAY OUTPUT
2 Z1 20BK GROUND
A/C COMPRESSOR
CLUTCH
BLACK
A E CAV CIRCUIT FUNCTION

A C7 12BR/TN HIGH SPEED BLOWER MOTOR
B D M2 SPEED BLOWER MOTOR
B C6 14LB
C C C5 16LG/LB M1 SPEED BLOWER MOTOR
D C4 16TN LOW SPEED BLOWER MOTOR
A/C-HEATER
CONTROL - C1 E C1 12DG BLOWER MOTOR FEED
BLACK CAV CIRCUIT FUNCTION

1 Z11 20BK/WT GROUND
1 F24 20RD/DG FUSED IGNITION SWITCH OUTPUT (RUN)
5 1 2 C36 20DB/RD BLEND DOOR FEEDBACK SIGNAL
A/C-HEATER 4 E2 20OR FUSED PANEL LAMPS DIMMER SWITCH SIGNAL
CONTROL - C2 5 Z1 20BK GROUND
BLACK

A C A C90 20LG A/C SELECT INPUT
B C1 12DG BLOWER MOTOR FEED
C Z1 12BK GROUND
A/C-HEATER
CONTROL - C3
BLACK
1 2

1 C90 20LG A/C SELECT INPUT
2 C21 20DB/OR A/C SWITCH SENSE
A/C HIGH
PRESSURE SWITCH
LHD
RHD
J998W-5 TJI08004
TJ 8W-80 CONNECTOR PIN-OUTS 8W - 80 - 5
GRAY
1 2

1 C22 20DB/WT A/C SWITCH SENSE
A/C LOW 2 C21 20DB/OR A/C SWITCH SENSE
PRESSURE SWITCH
BLACK
A B CAV CIRCUIT FUNCTION

A B48 20RD/YL ABS MAIN RELAY OUTPUT
B G19 20LG/OR ABS WARNING INDICATOR DRIVER
ABS DIODE
BLACK

1 B120 12BR/WT ABS PUMP MOTOR RELAY OUTPUT
2 Z1 12BK GROUND
2 1
ABS PUMP
MOTOR CAV CIRCUIT FUNCTION
1 R45 18DG/LB DRIVER AIRBAG LINE 2
2 R43 18BK/LB DRIVER AIRBAG LINE 1
3 - -
YELLOW 4 - -
5 R142 18BR/YL PASSENGER AIRBAG SQUIB LINE 1
6 R144 18VT/YL PASSENGER AIRBAG SQUIB LINE 2
7 - -
11 1
22 12 8 - -
9 - -
10 Z6 18BK/PK GROUND
11 - -
AIRBAG 12 - -
CONTROL - -
13
MODULE
14 - -
15 - -
16 - -
17 F14 18LG/YL FUSED IGNITION SWITCH OUTPUT (ST-RUN)
18 D2 18WT/BK CCD BUS(-)
19 D1 18VT/BR CCD BUS(+)
20 F23 18DB/YL FUSED IGNITION SWITCH OUTPUT (RUN)
21 - -
22 - -
BLACK

A B A L1 18VT/BK BACK-UP LAMP FEED
B F20 18VT/WT FUSED IGNITION SWITCH OUTPUT (RUN)
BACK-UP
LAMP SWITCH
(M/T)
TJI08005 J998W-5
BLACK
1 2 1 K118 18PK/YL BATTERY TEMPERATURE SENSOR SIGNAL
2 K167 20BR/YL SENSOR GROUND
BATTERY 2 K167 18BR/YL SENSOR GROUND
TEMPERATURE
SENSOR
GRAY CAV CIRCUIT FUNCTION

1 K29 20WT/PK BRAKE SWITCH SENSE
2 Z1 20BK GROUND
1 6 3 V32 20YL/RD SPEED CONTROL ON/OFF SWITCH SENSE
4 V30 20DB/RD SPEED CONTROL BRAKE SWITCH OUTPUT
BRAKE LAMP 5 F32 18PK/DB FUSED B(+)
SWITCH 6 L50 18WT/TN BRAKE LAMP SWITCH OUTPUT
WHITE

1 2 1 K29 20WT/PK BRAKE SWITCH SENSE
2 G5 20DB/WT FUSED IGNITION SWITCH OUTPUT (ST-RUN)
BRAKE SHIFT
INTERLOCK
SOLENOID
BLACK
1 2 1 G9 20GY/BK RED BRAKE WARNING INDICATOR DRIVER
2 G99 20GY/WT RED BRAKE WARNING INDICATOR DRIVER
BRAKE WARNING
INDICATOR SWITCH
CAV CIRCUIT CAV CIRCUIT

1 F142 20OR/DG 1 F142 18OR/DG
2 K72 18DG/OR 2 K72 18DG/OR
3 A14 14RD/WT 3 A14 14RD/WT
BLACK 4 B6 18WT/DB 4 B6 18WT/DB
BLACK
5 B7 18WT 5 B7 18WT
6 K226 18DB/LG 1 7 6 K226 20DB/LG
7 1
7 A141 18DG/WT 7 A141 18DG/WT
14 8 8 14
8 K167 20BR/YL 8 K167 20BR/YL
9 F12 20RD/LG 9 F12 20RD/LG
C103 10 Z12 20BK/TN C103 10 Z12 20BK/TN
11 Z12 20BK/LB 11 Z12 20BK/LB
12 G7 20WT/OR 12 G7 20WT/OR
13 G107 20BK/RD 13 G107 20BK/RD
ABS
14 C3 20DB/BK 14 C3 20DB/BK
DRL
LHD
RHD
J998W-5 TJI08006

1 C90 20LG 1 C90 20LG
2 C22 18DB/WT 2 C22 20DB/WT
3 B4 18LG 3 B4 18LG
GREY 4 B3 18LG/DB 4 B3 18LG/DB
GREY
5 T41 20BR/LB 5 T41 20BR/LB
7 1 6 B2 18YL 1 7 6 B2 18YL
14 8 7 B1 18YL/DB 8 14 7 B1 18YL/DB
8 - 8 -
9 L1 20VT/BK 9 L1 20VT/BK
C104 10 F20 20VT/WT C104 10 F20 20VT/WT
(LHD) 11 F42 18DG/LG (LHD) 11 F42 18DG/LG
12 T40 12BR 12 T40 12BR
13 F15 20DB 13 F15 18DB
14 - 14 -

1 C90 20LG 1 C90 20LG
BLACK BLACK
2 C22 18DB/WT 2 C22 20DB/WT
3 - 3 -
4 F42 18DG/LG 4 F42 18DG/LG
5 1 1 5
5 T41 20BR/LB 5 T41 20BR/LB
10 6 6 10
6 T40 12BR 6 T40 12BR
7 F15 20DB 7 F15 18DB
8 - 8 -
C104 C104
(RHD) (RHD)
10 F20 20VT/WT 10 F20 20VT/WT

F1 F30 12RD/PK F1 F30 12RD/PK
F2 L1 20VT/BK F2 L1 20VT/BK
F3 F20 20VT/WT F3 F20 20VT/WT
F4 F15 20DB F4 F15 20DB
BLACK F5 A1 14RD BLACK F5 A1 14RD
F6 A2 12PK/BK F6 A2 12PK/BK
F1 F6 F6 F1
F7 A6 12RD/BK F7 A6 12RD/BK
F8 C15 12BK/WT F12 F7 F8 C15 12BK/WT
F7 F12
T141 14YL/RD
F9 T141 14YL/RD F9
C106 T141 14YL/RD
C106
F10 F12 20RD/LG F10 F12 20RD/LG
G9 20GY/BK
F11 G9 20GY/BK F11
G9 20GY/BK
F12 A111 12RD/LB F12 A111 12RD/LB
ABS
TJI08007 J998W-5

L7 18BK/YL
E1 L7 18BK/YL E1
L7 18BK/YL
E2 L60 18TN E2 L60 18TN
E3 L61 18GY E3 L61 18GY
YELLOW L3 16RD/OR YELLOW
E4 E4 L3 14RD/OR
E5 L4 16VT/WT E5 L4 14VT/WT
E1 E7 E6 Z12 20BK/LB E7 E1 E6 Z12 20BK/LB
E7 X3 20RD/YL E14 E8 E7 X3 20RD/YL
E8 E14 E8 V10 18BR E8 V10 18BR
E9 Z12 20BK/TN E9 Z12 20BK/TN
C107 C107
E10 L39 18LB E10 L39 18LB
E11 V30 20DB/RD E11 V30 20DB/RD
E12 - E12 -
E13 D20 18LG E13 D20 20LG
D21 18PK
E14 E14 D21 20PK
D21 20PK

D1 V32 18YL/RD D1 V32 20YL/RD
G19 20LG/OR G19 20 LG/OR
D2 D2
BLUE G19 20LG/OR BLUE
D3 K167 20BR/YL D3 K167 20BR/YL
D1 D7 D4 D1 18VT/BR D4 D1 20VT/BR
D7 D1
D5 D2 18WT/BK D5 D2 20WT/BK
D14 D8
D8 D14 D6 F61 18WT/OR D6 F61 18WT/OR
G34 18RD/GY
D7 D7 G34 16RD/GY
L3 16RD/OR
C108 C108
D8 L20 16LG/WT D8 L20 16LG/WT
L50 18WT/TN
D9 L50 18WT/TN D9
L50 18WT/TN
D10 V37 18RD/LG D10 V37 20RD/LG
D11 L9 16BK/WT D11 L9 16BK/WT
M1 20PK/WT M1 20PK/WT
D12 D12
M1 20PK/WT M1 20PK/WT
D13 L22 20LG/DG D13 L22 20LG/DG
K29 20WT/PK
D14 K29 18WT/PK D14
K29 20WT/PK
DRL
EXCEPT DRL
LHD
SPEED CONTROL
FRONT FOG LAMPS
BUILT-UP-EXPORT
ABS
J998W-5 TJI08008

1 L7 18BK/YL 1 L7 18BK/YL
2 L60 18TN 2 L60 18TN
BLACK BLACK
3 L61 18GY 3 L61 18GY
4 L3 16RD/OR 4 L3 16RD/OR
5 L4 16VT/WT 5 L4 16VT/WT
7 1 6 X2 18WT/RD 1 7 6 X2 18WT/RD
14 8 7 - 8 14 7 -
8 V10 18BR 8 V10 18BR
9 L22 20LG/DG 9 L22 20LG/DG
C110 C110
10 K52 20PK/BK 10 K52 18PK/BK
11 F12 20RD/LG 11 F12 20RD/LG
12 - 12 -
13 L39 18LB 13 L39 18LB
14 L13 20BR/YL 14 L13 20BR/YL
BLACK
BLACK
1 Z1 20BK 1 Z1 20BK
4 1 1 4 3 T41 20BR/LB
3 T41 20BR/LB
3 Z1 20BK
C154 4 F20 20VT/WT 4 F20 18VT/WT
C154
M/T
A/T
BUILT-UP-EXPORT
FRONT FOG LAMPS
TJI08009 J998W-5

LIGHT 1 L13 20BR/YL 1 L13 20BR/YL
GRAY 2 C81 20LB/WT BLACK 2 C81 20LB/WT
3 G99 20GY/WT 3 G99 20GY/WT
4 A3 14RD/WT 4 A3 14RD/WT
5 1 5 5
5 1 G107 20BK/RD G107 20BK/RD
6 C90 20LG 6 10 6 C90 20LG
10 6
7 - 7 -
8 - C170 8 -
C170 9 - 9 -
10 - 10 -
BLACK BLACK
2 1
CAV CIRCUIT 1 2 CAV CIRCUIT
1 K105 18WT/OR 1 K105 20WT/OR
2 K106 18WT/DG 2 K106 20WT/DG
3 3 F142 20OR/DG 3 F142 20OR/DG
3
C180
C180

F24 20RD/DG
A1 A1 F24 20RD/DG
F24 20RD/DG
L20 16LG/WT
A2 L20 16LG/WT A2
L20 14LG/WT
A3 E1 18TN A3 E1 18TN
GRAY GRAY
A4 E2 20OR A4 E2 20OR
A1 A6 A5 F81 20DB/RD A5 F81 20DB/RD
A6 A1
Z12 20BK/LB
A6 Z12 20BK/LB A6
A7 A12 A12 A7 Z12 20BK/LB
A7 - A7 -
C202 C202 L2 14LG
A8 L2 16LG A8
L2 16LG
A9 F38 16LB A9 F38 16LB
A10 G5 20DB/WT A10 G5 20DB/WT
F34 18TN/BK
A11 F34 18TN/BK A11
F34 20TN/BK
A12 A111 12RD/LB A12 A111 12RD/LB
EXCEPT DRL
REAR FOG LAMP
DRL
BUILT-UP-EXPORT
HARDTOP
J998W-5 TJI08010

L60 18TN
B1 L60 18TN B1
L60 18TN
L61 18GY
B2 L61 18GY B2
L61 18GY
G26 20LB
B3 B3 G26 20LB
GREEN G26 20LB GREEN
G16 20BK/LB
B4 G16 20BK/LB B4
B1 B7 G16 20BK/LB
B7 B1
G34 16RD/GY
B5 G34 16RD/GY B14 B8 B5
B8 B14 G34 16RD/GY
L7 18BK/YL L7 18BK/YL
B6 C203 B6
C203 L7 18BK/YL L7 18BK/YL
B7 M1 20PK/WT B7 M1 20PK/WT
B8 D20 20LG B8 D20 20LG
B9 V20 18VT/OR B9 V20 18VT/OR
B10 D21 20PK B10 D21 20PK
D1 20VT/BR
B11 B11 D1 20VT/BR
D1 20VT/BR
D2 20WT/BK
B12 B12 D2 20WT/BK
D2 20WT/BK
B13 L35 18BR/WT B13 L35 18BR/WT
B14 G19 20LG/OR B14 G19 20LG/OR

C1 L95 18DG/YL C1 L95 18DG/YL
C2 V13 18BR/LG C2 V13 18BR/LG
C3 G10 20LG/RD C3 G10 20LG/RD
RED C4 Z12 20BK/TN RED C4 Z12 20BK/TN
C5 M2 20YL C5 M2 20YL
C1 C7 C7 C1
C6 V23 18BR/PK C6 V23 18BR/PK
C7 - C14 C8 C7 -
C8 C14
L38 20BR/WT
C8 L38 20BR/WT C8
C204 C204 L38 20BR/WT
L22 20LG/DG
C9 L22 20LG/DG C9
L22 20LG/DG
C10 X12 20PK C10 X12 20PK
C11 X51 18BR/YL C11 X51 18BR/YL
C12 X57 18BR/LB C12 X57 18BR/LB
C13 X52 18DB/WT C13 X52 18DB/WT
C14 X58 18DB/PK C14 X58 18DB/PK
REAR FOG LAMPS

HARD TOP
FRONT FOG LAMPS
BUILT-UP-EXPORT
LHD BUILT-UP-EXPORT
TJI08011 J998W-5

G1 L7 18BK/YL BLACK G1 L7 18BK/YL
BLACK
G2 L62 18BR/RD G2 L62 18BR/RD
G3 L1 20VT/BK G3 L1 20VT/BK
G1 G5 G5 G1
G4 L63 18DG/RD G4 L63 18DG/RD
G5 Z1 12BK G10 G6 G5 Z1 12BK
G6 G10
G6 G10 20LG/RD G6 G10 20LG/RD
C322 C322 L50 18WT/TN
G7 L50 18WT/TN G7
(LHD) (LHD) L50 18WT/TN
G8 L38 20BR/WT G8 L38 20BR/WT
G9 G9 20GY/BK G9 G9 20GY/BK
G10 V23 18BR/PK G10 V23 18BR/PK

BLACK 1 L7 18BK/YL 1 L7 18BK/YL
2 L62 18BR/RD BLACK 2 L62 18BR/RD
5 1 4 L63 18DG/RD 1 5 4 L63 18DG/RD
10 6 5 Z1 12BK 6 10 5 Z1 12BK
6 G10 20LG/RD 6 G10 20LG/RD
7 L50 18WT/TN 7 L50 18WT/TN
C322 C322
8 L38 20BR/WT 8 L38 20BR/WT
(RHD) (RHD)
9 G9 20GY/BK 9 G9 20GY/BK
10 V23 18BR/PK 10 V23 18BR/PK

H1 C15 12BK/WT H1 C15 12BK/WT
RED RED
H2 M1 20PK/WT H2 M1 20PK/WT
H3 M2 20YL H3 M2 20YL
H1 H5
H4 V23 18BR/PK H5 H1 H4 V23 18BR/PK
H5 V13 18BR/LG H10 H6 H5 V13 18BR/LG
H6 H10
H6 V20 18VT/OR H6 V20 18VT/OR
H7 X51 18BR/YL H7 X51 18BR/YL
C323 C323 H8 X57 18BR/LB
H8 X57 18BR/LB
(LHD) H9 X52 18DB/WT (LHD) H9 X52 18DB/WT
H10 X58 18DB/PK H10 X58 18DB/PK
HARD TOP
REAR FOG LAMP
4 SPEAKER SYSTEM
THE FEMALE SIDE OF C323 IS NOT PRESENT
IN SOFT-TOP 2 - SPEAKER SYSTEM VEHICLES
J998W-5 TJI08012

1 C15 12BK/WT 1 C15 12BK/WT
Lt GRAY 2 M1 20PK/WT 2 M1 20PK/WT
3 Lt GRAY
M2 20YL 3 M2 20YL
4 V23 18BR/PK 4 V23 18BR/PK
5 1 5 V13 18BR/LG 1 5 5 V13 18BR/LG
10 6 6 V20 18VT/OR 6 10 6 V20 18VT/OR
7 X51 18BR/YL 7 X51 18BR/YL
C323 8 X57 18BR/LB C323 8 X57 18BR/LB
(RHD) 9 X52 18DB/WT (RHD) 9 X52 18DB/WT
10 X58 18DB/PK 10 X58 18DB/PK
BLACK
WHITE CAV CIRCUIT CAV CIRCUIT
1 X57 18BR/LB 1 X57 18BR/LB
1 6 2 X51 18BR/YL 2 X51 18BR/YL
3 M1 20PK/WT 6 1 3 M1 20PK/WT
4 M2 20YL 4 M2 20YL
C325 5 X58 18DB/PK C325 5 X58 18DB/PK
(4 SPKR SYS)
6 X52 18DB/WT (4 SPKR SYS) 6 X52 18DB/WT

BLACK 1 C15 12BK/WT 1 C15 12BK/WT
BLACK
2 - 2 -
3 V13 18BR/LG 3 V13 18BR/LG
4 V23 18BR/PK 1 5 4 V23 18BR/PK
5 1
5 V23 18BR/PK 6 10 5 V23 18BR/PK
10 6
6 Z1 12BK 6 Z1 12BK
7 - 7 -
C326 8 M1 20PK/WT C326 8 M1 20PK/WT
(HARD TOP) 9 M2 20YL (HARD TOP) 9 M2 18YL
10 - 10 -
4 SPEAKER SYSTEM
HARD TOP
THE MALE SIDE OF C323 IS NOT PRESENT

IN SOFT-TOP 2 - SPEAKER SYSTEM VEHICLES
TJI08013 J998W-5
BLACK BLACK

1 2 2 1
1 L38 20BR/WT 1 L38 18BR/WT
3
2 L7 18BK/YL 2 L7 18BK/YL
3
3 Z1 20BK 3 Z1 20BK
C329 C329
BLACK
WHITE CAV CIRCUIT CAV CIRCUIT
1 X57 18BR/LB 1 X57 20BR/LB
1 6 2 X51 18BR/YL 2 X51 20BR/YL
3 M1 20PK/WT 6 1 3 M1 20PK/WT
4 M2 20YL 4 M2 20YL
C330 5 X58 18DB/PK C330 5 X58 20DB/PK
(4 SPKR SYS)
6 X52 18DB/WT (4 SPKR SYS) 6 X52 20DB/WT

BLACK 1 C15 12BK/WT 1 C15 12BK/WT
BLACK
2 - 2 -
3 V13 18BR/LG 3 V13 18BK/LG
4 V23 18BR/PK 1 5 4 V23 18BR/PK
5 1
5 V23 18BR/PK 6 10 5 V23 18BR/PK
10 6
6 Z1 12BK 6 Z1 12BK
7 - 7 -
C331 8 M1 20PK/WT C331 8 M1 20PK/WT
(HARD TOP) 9 M2 18YL (HARD TOP) 9 M2 20YL
10 - 10 -
GRAY
1 3
1 K44 18TN/YL CAMSHAFT POSITION SENSOR SIGNAL
3 K7 20OR 5V SUPPLY
CAMSHAFT POSITION
SENSOR
J998W-5 TJI08014
BLACK
1
1 F30 12RD/PK FUSED B(+)
5 2 2 A31 14BK/DG IGNITION SWITCH OUTPUT (RUN-ACC)
3 - -
4 F22 12WT/PK CIGAR LIGHTER/ACCESSORY RELAY OUTPUT
4 Z1 20BK GROUND
5
CIGAR LIGHTER/ Z1 20BK GROUND
ACCESSORY RELAY
RED
2 1 CAV CIRCUIT FUNCTION

1 F38 16LB FUSED B (+)
2 - -
3 3 Z1 16BK GROUND
CIGAR LIGHTER/
POWER OUTLET
YELLOW

2 1 1 R45 18DG/LB DRIVER AIRBAG LINE 2
2 R43 18BK/LB DRIVER AIRBAG LINE 1
CLOCKSPRING - C1
NATURAL CAV CIRCUIT FUNCTION

1 X3 20RD/YL HORN RELAY CONTROL
4 1 2 V37 20RD/LG SPEED CONTROL SWITCH SIGNAL
CLOCKSPRING - C2 4 - -
BLACK

1 T141 14YL/RD FUSED IGNITION SWITCH OUTPUT (ST)
CLUTCH PEDAL 2 A41 14YL FUSED IGNITION SWITCH OUTPUT (ST)
POSITION SWITCH
(M/T)

1 - -
2 L32 16PK COMBINATION FLASHER OUTPUT
3 2 1 3 - -
6 5 4 4 Z1 20BK GROUND
5 - -
9 8 7
6 L55 16RD/WT COMBINATION FLASHER INPUT
7 - -
COMBINATION 8 - -
FLASHER 9 - -
TJI08015 J998W-5

1 G19 20LG/OR ABS WARNING INDICATOR DRIVER
GRAY 2 B43 20PK/OR G-SWITCH TEST SIGNAL
3 D21 20PK SCI TRANSMIT/ISO 9141K
1 5 4 - -
6 12 5 F20 20VT/WT FUSED IGNITION SWITCH OUTPUT (RUN)
6 B41 20YL/VT G-SWITCH NO. 1 SENSE
CONTROLLER 7 B42 20TN/WT G-SWITCH NO. 2 SENSE
ANTI-LOCK 8 L50 18WT/TN BRAKE LAMP SWITCH OUTPUT
BRAKE - C1 9 B3 18LG/DB LEFT REAR WHEEL SPEED SENSOR (-)
10 B4 18LG LEFT REAR WHEEL SPEED SENSOR (+)
11 B1 18YL/DB RIGHT REAR WHEEL SPEED SENSOR (-)
12 B2 18YL RIGHT REAR WHEEL SPEED SENSOR (+)

1 B7 18WT RIGHT FRONT WHEEL SPEED SENSOR (+)
2 B6 18WT/DB RIGHT FRONT WHEEL SPEED SENSOR (-)
3 B120 16BR/WT ABS PUMP MOTOR RELAY OUTPUT
4 B251 20WT/BK REAR INLET VALVE CONTROL
5 B48 20RD/YL ABS MAIN RELAY OUTPUT
GRAY
6 B248 20DG/WT RIGHT FRONT OUTLET VALVE CONTROL
7 B116 20GY ABS PUMP MOTOR RELAY CONTROL
1 8
9 18 8 B243 20DG/BK LEFT FRONT OUTLET VALVE CONTROL
9 B9 18RD LEFT FRONT WHEEL SPEED SENSOR (+)
CONTROLLER 10 B8 18RD/DB LEFT FRONT WHEEL SPEED SENSOR (-)
ANTI-LOCK 11 B58 20GY/LB ABS MAIN RELAY CONTROL
BRAKE - C2 12 B254 20DG/OR REAR OUTLET VALVE CONTROL
15 B249 20WT/DG RIGHT FRONT INLET VALVE CONTROL
16 - -
17 - -
18 B245 20WT/LG LEFT FRONT INLET VALVE CONTROL
BLACK
1 3 1 K24 18GY/BK CRANKSHAFT POSITION SENSOR SIGNAL
3 K7 20OR 5V SUPPLY
CRANKSHAFT
POSITION
SENSOR
J998W-5 TJI08016

1 - -
2 - -
4 Z12 20BK/LB GROUND
BLACK 5 Z12 20BK/TN GROUND
6 D20 20LG SCI RECEIVE
1 8 7 D21 20PK SCI TRANSMIT/ISO 9141K
9 16 8 - -
9 - -
DATA LINK 10 - -
CONNECTOR 11 D2 20WT/BK CCD BUS(-)
12 - -
13 - -
14 - -
15 - -
16 M1 20PK/WT FUSED B(+)

1 L3 16RD/OR DIMMER SWITCH HIGH BEAM OUTPUT
BLACK
2 - -
5 1 3 - -
4 G34 18RD/GY HIGH BEAM INDICATOR DRIVER
5 F12 20RD/LG FUSED IGNITION SWITCH OUTPUT (ST-RUN)
6 L20 16LG/WT FUSED B(+) OPTICAL HORN FEED
10 6
7 G7 20WT/OR VEHICLE SPEED SENSOR SIGNAL
DAYTIME RUNNING 8 Z1 18BK GROUND
LAMP MODULE 9 - -
(EXCEPT BUILT- 10 L4 16VT/WT DIMMER SWITCH LOW BEAM OUTPUT
UP-EXPORT)
TJI08017 J998W-5
NATURAL
1
1 M23 20YL/BK DOOR AJAR SWITCH OUTPUT
2 3 2 M2 20YL COURTESY LAMPS DRIVER
DRIVER DOOR 3 G16 20BK/LB DRIVER DOOR AJAR SWITCH SENSE
AJAR SWITCH
BLACK

1 K52 20PK/BK DUTY CYCLE EVAP/PURGE SOLENOID CONTROL
2 F12 20RD/LG FUSED IGNITION SWITCH OUTPUT (ST-RUN)
DUTY CYCLE
EVAP/PURGE
SOLENOID
BLACK
1 2

1 K2 18TN/BK ENGINE COOLANT TEMPERATURE SENSOR SIGNAL
ENGINE COOLANT
TEMPERATURE
SENSOR
BLACK

3 1 1 K6 20VT/OR 5V SUPPLY
2 G60 18GY/YL ENGINE OIL PRESSURE SENSOR SIGNAL
ENGINE OIL
PRESSURE
SENSOR
J998W-5 TJI08018
BLACK

2 4 1
1 L35 18BR/WT FOG LAMP SWITCH OUTPUT
5 2 Z1 20BK GROUND
3 3 F61 18WT/OR FUSED B(+)
4 - -
FOG LAMP 5 L39 18LB FOG LAMP RELAY NO. 1 OUTPUT
RELAY NO. 1
(EXCEPT BUILT-
UP-EXPORT)
BLACK

2 4 1 1 G34 16RD/GY HIGH BEAM INDICATOR DRIVER
5 Z1 20BK GROUND
2
3 Z1 20BK GROUND
3 L7 18BK/YL HEADLAMP SWITCH OUTPUT
FOG LAMP 4 L95 18DG/YL FOG LAMP RELAY OUTPUT
RELAY NO. 2 5 - -
(EXCEPT BUILT-
UP-EXPORT)
BLACK
1 E2 20OR FUSED PANEL LAMPS DIMMER SWITCH SIGNAL
2 L35 18BR/WT FOG LAMP SWITCH OUTPUT
12 3 4 3 L95 18DG/YL FOG LAMP RELAY OUTPUT
4 Z1 20BK GROUND
FRONT FOG
LAMP SWITCH
(EXCEPT BUILT-
UP-EXPORT)
BLACK

1 2 1 F42 18DG/LG AUTOMATIC SHUT DOWN RELAY OUTPUT
2 K11 18WT/DB FUEL INJECTOR NO. 1 DRIVER
FUEL INJECTOR NO. 1
(2.5L)
2 1 BLACK

1 F42 18DG/LG AUTOMATIC SHUT DOWN RELAY OUTPUT
2 K11 18WT/DB FUEL INJECTOR NO. 1 DRIVER
FUEL INJECTOR NO. 1

(4.0L)
TJI08019 J998W-5
BLACK

2 K12 18TN FUEL INJECTOR NO. 2 DRIVER
FUEL INJECTOR NO. 2

(2.5L)
2 1 BLACK

2 K12 18TN FUEL INJECTOR NO. 2 DRIVER
FUEL INJECTOR NO. 2

(4.0L)
BLACK

2 K13 18YL/WT FUEL INJECTOR NO. 3 DRIVER
FUEL INJECTOR NO. 3

(2.5L)
2 1 BLACK

2 K13 18YL/WT FUEL INJECTOR NO. 3 DRIVER
FUEL INJECTOR NO. 3

(4.0L)
BLACK

2 K14 18LB/BR FUEL INJECTOR NO. 4 DRIVER
FUEL INJECTOR NO. 4

(2.5L)
J998W-5 TJI08020
2 1 BLACK

2 K14 18LB/BR FUEL INJECTOR NO. 4 DRIVER
FUEL INJECTOR NO. 4

(4.0L)
2 1 BLACK

2 K15 18PK/BK FUEL INJECTOR NO. 5 DRIVER
FUEL INJECTOR NO. 5

(4.0L)
2 1 BLACK

2 K16 18LG/BK FUEL INJECTOR NO. 6 DRIVER
FUEL INJECTOR NO. 6

(4.0L)
BLACK
1 A141 18DG/WT FUEL PUMP RELAY OUTPUT
3 1 2 - -
3 K226 20DB/LG FUEL LEVEL SENSOR SIGNAL
6 4 4 K167 20BR/YL SENSOR GROUND
5 - -
FUEL PUMP 6 Z1 18BK GROUND
MODULE
BLACK
1 B42 20TN/WT G-SWITCH NO.2 SENSE
1 3 2 B41 20YL/VT G-SWITCH NO.1 SENSE
3 B43 20PK/OR G-SWITCH TEST SIGNAL
G SWITCH
BLACK

1 K72 18DG/OR VOLTAGE REGULATOR SIGNAL
2 K20 18DG GENERATOR FIELD DRIVER (+)
GENERATOR
TJI08021 J998W-5
BLACK
1 L4 14VT/WT DIMMER SWITCH LOW BEAM OUTPUT
4 1 2 L2 14LG HEADLAMP SWITCH OUTPUT
3 L3 14RD/OR DIMMER SWITCH HIGH BEAM OUTPUT
HEADLAMP 4 L20 14LG/WT FUSED B(+) OPTICAL HORN FEED
DIMMER
SWITCH
WHITE
1 - -
2 L22 20LG/DG HEADLAMP SWITCH FUSED OUTPUT
1 6
3 - -
4 Z1 20BK GROUND
HEADLAMP
5 L13 20BR/YL HEADLAMP ADJUST SIGNAL
LEVELING
6 - -
SWITCH
(BUILT-UP-EXPORT)

6 BLACK
8 1 E1 18TN PANEL LAMPS DIMMER SWITCH SIGNAL
5 2 L2 16LG HEADLAMP SWITCH OUTPUT
7 3 M2 20YL COURTESY LAMPS DRIVER
4 9 4 F34 18TN/BK FUSED B(+)
2 5 G26 20LB KEY-IN IGNITION SWITCH SENSE
3 6 G16 20BK/LB DRIVER AJAR SWITCH SENSE
1 7 L20 16LG/WT FUSED B(+) OPTICAL HORN FEED
HEADLAMP 8 A3 14RD/WT FUSED B(+)
SWITCH 9 L7 18BK/YL HEADLAMP SWITCH OUTPUT
BLACK
2
1 1 X2 18WT/RD HORN RELAY OUTPUT
2 Z1 18BK GROUND
HIGH NOTE
HORN

2 C4 16TN LOW SPEED BLOWER MOTOR
GRAY
3 C5 16LG/LB M1 SPEED BLOWER MOTOR
4 C6 14LB M2 SPEED BLOWER MOTOR
F24 20RD/DG FUSED IGNITION SWITCH OUTPUT (RUN)
5 1 5
F24 20RD/DG FUSED IGNITION SWITCH OUTPUT (RUN)
10 6 6 C36 20DB/RD BLEND DOOR FEEDBACK SIGNAL
7 C7 12BR/TN HIGH SPEED BLOWER MOTOR
8 A111 12RD/LB FUSED B(+)
HVAC
UNIT
10 Z1 20BK GROUND
J998W-5 TJI08022

BLACK 1 B47 14RD/LB ABS SYSTEM RELAY OUTPUT
2 B251 20WT/BK REAR INLET VALVE CONTROL
3 B249 20WT/DG RIGHT FRONT INLET VALVE CONTROL
5 1 4 B245 20WT/LG LEFT FRONT INLET VALVE CONTROL
10 6 5 - -
6 - -
HYDRAULIC 7 B254 20DG/OR REAR OUTLET VALVE CONTROL
CONTROL 8 B248 20DG/WT RIGHT FRONT OUTLET VALVE CONTROL
UNIT 9 B243 20DG/BK LEFT FRONT OUTLET VALVE CONTROL
10 B47 14RD/LB ABS SYSTEM RELAY OUTPUT
BLACK
1 4
1 K59 18VT/BK IDLE AIR CONTROL NO. 4 DRIVER
2 K40 18BR/WT IDLE AIR CONTROL NO. 3 DRIVER
3 K60 18YL/BK IDLE AIR CONTROL NO. 2 DRIVER
IDLE AIR
4 K39 18GY/RD IDLE AIR CONTROL NO. 1 DRIVER
CONTROL MOTOR
GRAY

2 K19 18GY IGNITION COIL NO. 1 DRIVER
IGNITION
COIL

1 Z1 16BK GROUND
2 G9 20GY/BK RED BRAKE WARNING INDICATOR DRIVER
GRAY 3 A2 12PK/BK FUSED B(+)
4 A22 12BK/OR IGNITION SWITCH OUTPUT (RUN)
5 1 5 - -
10 6 6 - -
7 A1 14RD FUSED B(+)
IGNITION 8 A31 14BK/DG IGNITION SWITCH OUTPUT (RUN-ACC)
SWITCH 9 A21 14DB IGNITION SWITCH OUTPUT (ST-RUN)
10 A41 14YL IGNITION SWITCH OUTPUT (ST)
TJI08023 J998W-5

GREEN 1 D2 20WT/BK CCD BUS(-)
3 C81 20LB/WT REAR WINDOW DEFOGGER RELAY CONTROL
4 C80 20DB/LG REAR WINDOW DEFOGGER SWITCH SENSE
5 1 5 G107 20BK/RD 4WD SENSE
10 6 6 L60 18TN RIGHT TURN SIGNAL
7 - -
8 G26 20LB KEY-IN IGNITION SWITCH SENSE
INSTRUMENT 9 Z2 18BK/LG GROUND
CLUSTER - C1 10 G10 20LG/RD SEAT BELT SWITCH SENSE

BLUE 1 - -
2 G99 20GY/WT RED BRAKE WARNING INDICATOR DRIVER
4 G19 20LG/OR ABS WARNING INDICATOR DRIVER
5 1 5 G34 16RD/GY HIGH BEAM INDICATOR DRIVER
10 6 6 Z2 18BK/LG GROUND
7 - -
INSTRUMENT 8 G5 20DB/WT FUSED IGNITION SWITCH OUTPUT (ST-RUN)
CLUSTER - C2 9 M1 20PK/WT FUSED B(+)
10 L61 18GY LEFT TURN SIGNAL
GRAY
1 2
1 K21 18BK/RD INTAKE AIR TEMPERATURE SENSOR SIGNAL
INTAKE AIR
TEMPERATURE
SENSOR
GREEN

2 1 1 G16 20BK/LB DRIVER AJAR SWITCH SENSE
2 G26 20LB KEY-IN IGNITION SWITCH SENSE
KEY-IN
SWITCH
HARD TOP
J998W-5 TJI08024
BLACK
1 - -
4 1
2 F142 20OR/DG FUSED AUTOMATIC SHUTDOWN RELAY OUTPUT
3 K106 20WT/DG LEAK DETECTION PUMP SOLENOID CONTROL
4 K105 20WT/OR LEAK DETECTION PUMP SWITCH SENSE
LEAK
DETECTION PUMP
(EXCEPT BUILT-
UP-EXPORT)
BLACK
2 CAV CIRCUIT FUNCTION
1 1 L7 18BK/YL HEADLAMP SWITCH OUTPUT
2 Z1 18BK GROUND
LEFT CITY
LAMP
(BUILT-UP-EXPORT)
BLACK

2 M2 20YL COURTESY LAMPS DRIVER
LEFT
COURTESY LAMP
BLACK
1 2 1 Z1 18BK GROUND
2 L39 18LB FOG LAMP RELAY NO. 1 OUTPUT
LEFT FOG
LAMP
(EXCEPT BUILT-UP
-EXPORT)
BLACK

1
LEFT FRONT PARK/ 2 L7 18BK/YL HEADLAMP SWITCH OUTPUT
TURN SIGNAL LAMP 3 Z1 18BK GROUND
(EXCEPT BUILT-UP
-EXPORT)
BLACK
1 2 1 X53 18DG LEFT FRONT SPEAKER (+)
2 X55 18BR/RD LEFT FRONT SPEAKER (-)
LEFT
FRONT SPEAKER
TJI08025 J998W-5
BLACK
1 3
2 - -
LEFT FRONT
3 Z1 18BK GROUND
TURN SIGNAL LAMP
(BUILT-UP-EXPORT)
BLACK

1 B8 18RD/DB LEFT FRONT WHEEL SPEED SENSOR (-)
2 B9 18RD LEFT FRONT WHEEL SPEED SENSOR (+)
LEFT FRONT
WHEEL SPEED
SENSOR
BLACK
2
L3 16RD/OR DIMMER SWITCH HIGH BEAM OUTPUT
1 3 1
L3 16RD/OR DIMMER SWITCH HIGH BEAM OUTPUT
3 Z1 20BK GROUND
LEFT HEADLAMP
BLACK

1 3 1 L22 20LG/DG HEADLAMP SWITCH FUSED OUTPUT
3 Z1 20BK GROUND
LEFT HEADLAMP
LEVELING MOTOR
(BUILT-UP-EXPORT)
GRAY
1 2

2 Z1 20BK GROUND
LEFT LICENSE
LAMP
(BUILT-UP-EXPORT)
J998W-5 TJI08026
BLACK
L1 20VT/BK BACK-UP LAMP FEED
1
1 2 L63 18DG/RD LEFT TURN SIGNAL
L63 18DG/RD LEFT TURN SIGNAL
3 4 2
L7 18BK/YL HEADLAMP SWITCH OUTPUT
3
LEFT REAR L50 18WT/TN BRAKE LAMP SWITCH OUTPUT
LAMP ASSEMBLY 4 L7 18BK/YL HEADLAMP SWITCH OUTPUT
BLACK

1 2 1 X51 20BR/YL LEFT REAR SPEAKER (+)
2 X57 20BR/LB LEFT REAR SPEAKER (-)
LEFT REAR
SPEAKER
(SOUND BAR)
BLACK

1 B3 18LG/DB LEFT REAR WHEEL SPEED SENSOR (-)
2 1
2 B4 18LG LEFT REAR WHEEL SPEED SENSOR (+)
LEFT REAR
WHEEL SPEED
SENSOR
GRAY

1 1 L61 18GY LEFT TURN SIGNAL
2 Z1 18BK GROUND
LEFT REPEATER
LAMP
(BUILT-UP-EXPORT)
GRAY

1 2 L61 18GY LEFT TURN SIGNAL
LEFT SIDE
MARKER LAMP
(EXCEPT BUILT-
UP-EXPORT)
BLACK

2
1 1 X2 18WT/RD HORN RELAY OUTPUT
2 Z1 18BK GROUND
LOW NOTE
HORN
(EXCEPT BUILT- EXCEPT BUILT-UP-EXPORT
UP-EXPORT)
BUILT-UP-EXPORT
TJI08027 J998W-5
BLACK

1 3 1 K167 20BR/YL SENSOR GROUND
2 K1 18DG/RD MANIFOLD ABSOLUTE PRESSURE SENSOR SIGNAL
MANIFOLD 3 K7 20OR 5V SUPPLY
ABSOLUTE
PRESSURE
SENSOR
GRAY

1 F142 18OR/DG FUSED AUTOMATIC SHUT DOWN RELAY OUTPUT
3 4
2 Z1 18BK GROUND
OXYGEN SENSOR 4 K41 18BK/DG OXYGEN SENSOR 1/1 SIGNAL
1/1 UPSTREAM
BLACK
1 2
1 F142 18OR/DG FUSED AUTOMATIC SHUT DOWN RELAY OUTPUT
3 4
2 Z1 18BK GROUND
OXYGEN SENSOR 4 K141 18TN/WT OXYGEN SENSOR 1/2 SIGNAL
1/2 DOWNSTREAM

1 3 1 F20 18VT/WT FUSED IGNITION SWITCH OUTPUT (RUN)
2 T41 20BR/LB PARK/NEUTRAL POSITION SWITCH SENSE
PARK/NEUTRAL 3 L1 18VT/BK BACK-UP LAMP FEED
POSITION SWITCH
(A/T)
YELLOW

A R44 18DG/YL PASSENGER AIRBAG LINE 2
A B
B R42 18BK/YL PASSENGER AIRBAG LINE 1
PASSENGER
AIRBAG
J998W-5 TJI08028
LIGHT
GRAY
1 2
1 F14 18LG/YL FUSED IGNITION SWITCH OUTPUT (ST-RUN)
2 Z6 20BK/PK GROUND
PASSENGER AIRBAG
ON/OFF SWITCH - C1
YELLOW
1 R142 18BR/YL PASSENGER AIRBAG SQUIB LINE 1
1 4 2 R144 18VT/YL PASSENGER AIRBAG SQUIB LINE 2
3 R42 18BK/YL PASSENGER AIRBAG LINE 1
4 R44 18DG/YL PASSENGER AIRBAG LINE 2
PASSENGER AIRBAG
ON/OFF SWITCH - C2
1 BLACK

1 M23 20YL/BK DOOR AJAR SWITCH OUTPUT
2
PASSENGER
DOOR AJAR
SWITCH
BLACK

1 Z1 18BK GROUND
2 K10 18DB/BR POWER STEERING PRESSURE SWITCH SENSE
POWER STEERING
PRESSURE SWITCH
(2.5L)
LHD
RHD
TJI08029 J998W-5

A1 - -
A2 F15 18DB FUSED IGNITION SWITCH OUTPUT (ST-RUN)
A3 - -
A4 K167 18BR/YL SENSOR GROUND
A5 - -
A6 T41 18BR/LB PARK/NEUTRAL POSITION SWITCH SENSE
A7 K19 18GY IGNITION COIL NO. 1 DRIVER
BLACK
A8 K24 18GY/BK CRANKSHAFT POSITION SENSOR SIGNAL
A9 - -
A10 K60 18YL/BK IDLE AIR CONTROL NO. 2 DRIVER
11 1 A11 K40 18BR/WT IDLE AIR CONTROL NO. 3 DRIVER
A12 K10 18DB/BR POWER STEERING PRESSURE SWITCH SENSE
32 22 A13 - -
A14 - -
A15 K21 18BK/RD INTAKE AIR TEMPERATURE SENSOR SIGNAL
A16 K2 18TN/BK ENGINE COOLANT TEMPERATURE SENSOR SIGNAL
POWERTRAIN
A17 K7 18OR 5V SUPPLY
CONTROL
A18 K44 18TN/YL CAMSHAFT POSITION SENSOR SIGNAL
MODULE - C1
A19 K39 18GY/RD IDLE AIR CONTROL NO. 1 DRIVER
A20 K59 18VT/BK IDLE AIR CONTROL NO. 4 DRIVER
A21 - -
A22 A14 14RD/WT FUSED B(+)
A23 K22 18OR/DB THROTTLE POSITION SENSOR SIGNAL
A24 K41 18BK/DG OXYGEN SENSOR 1/1 SIGNAL
A25 K141 18TN/WT OXYGEN SENSOR 1/2 SIGNAL
A26 - -
A27 K1 18DG/RD MANIFOLD ABSOLUTE PRESSURE SENSOR SIGNAL
A28 - -
A29 - -
A30 - -
A31 Z12 14BK/TN GROUND
A32 Z12 14BK/TN GROUND
2.5L
J998W-5 TJI08030

B1 - -
B2 - -
B3 - -
B4 K11 18WT/DB FUEL INJECTOR NO. 1 DRIVER
B5 K13 18YL/WT FUEL INJECTOR NO. 3 DRIVER
B6 K15 18PK/BK FUEL INJECTOR NO. 5 DRIVER
B7 - -
WHITE
B8 - -
B9 - -
B10 K20 18DG GENERATOR FIELD DRIVER (+)
11 1 B11 T23 18OR/LG TRANSMISSION LOW/OVERDRIVE SOLENOID
B12 K16 18LG/BK FUEL INJECTOR NO. 6 DRIVER
32 22
B13 - -
B14 - -
B15 K12 18TN FUEL INJECTOR NO. 2 DRIVER
B16 K14 18LB/BR FUEL INJECTOR NO. 4 DRIVER
POWERTRAIN B17 - -
CONTROL B18 - -
MODULE - C2
B19 - -
B20 - -
B21 - -
B22 - -
B23 G60 18GY/YL ENGINE OIL PRESSURE SENSOR SIGNAL
B24 - -
B25 - -
B26 - -
B27 G7 18WT/OR VEHICLE SPEED SENSOR SIGNAL
B28 - -
B29 - -
B30 - -
B31 K6 18VT/OR 5V SUPPLY
B32 - -
4.0L
TJI08031 J998W-5

C1 C13 18DB/OR A/C COMPRESSOR CLUTCH RELAY CONTROL
C2 - -
C3 K51 18DB/YL AUTOMATIC SHUT DOWN RELAY CONTROL
C4 V36 18TN/RD SPEED CONTROL VACUUM SOLENOID CONTROL
C5 V35 18LG/RD SPEED CONTROL VENT SOLENOID CONTROL
C6 - -
C7 - -
C8 - -
GRAY C9 - -
C10 K106 18WT/DG LEAK DETECTION PUMP SOLENOID CONTROL
C11 V32 18YL/RD SPEED CONTROL ON/OFF SWITCH SENSE
C12 A142 14DG/PK AUTOMATIC SHUT DOWN RELAY OUTPUT SENSE
11 1 C13 - -
32 22 C14 K105 18WT/OR LEAK DETECTION PUMP SWITCH SENSE
C15 K118 18PK/YL BATTERY TEMPERATURE SENSOR SIGNAL
C16 - -
C17 - -
POWERTRAIN C18 - -
CONTROL C19 K31 18BR FUEL PUMP RELAY CONTROL
MODULE - C3 C20 K52 18PK/BK DUTY CYCLE EVAP/PURGE SOLENOID CONTROL
C21 - -
C22 C22 18DB/WT A/C SWITCH SENSE
C23 C90 18LG A/C SELECT INPUT
C24 K29 18WT/PK BRAKE SWITCH SENSE
C25 K72 18DG/OR VOLTAGE REGULATOR SIGNAL
C26 K226 18DB/LG FUEL LEVEL SENSOR SIGNAL
C27 D21 18PK SCI TRANSMIT/ISO 9141K
C28 D2 18WT/BK CCD BUS(-)
C29 D20 18LG SCI RECEIVE
C30 D1 18VT/BR CCD BUS(+)
C31 - -
C32 V37 18RD/LG SPEED CONTROL SWITCH SIGNAL
BLACK

1 2 1 E2 20OR FUSED PANEL LAMPS DIMMER SWITCH SIGNAL
2 Z1 20BK GROUND
PRNDL LAMP
SPEED CONTROL
LEAK DETECTION
J998W-5 TJI08032

GRAY
1 - -
2 X55 18BR/RD LEFT FRONT SPEAKER(-)
7 1 3 X56 18DB RIGHT FRONT SPEAKER(-)
RADIO - C1 5 E2 20OR FUSED PANEL LAMPS DIMMER SWITCH SIGNAL
6 X12 20PK FUSED IGNITION SWITCH OUTPUT (RUN-ACC)

BLACK
1 - -
2 X51 18BR/YL LEFT REAR SPEAKER(+)
7 1 3 X52 18DB/WT RIGHT REAR SPEAKER(+)
4 X53 18DG LEFT FRONT SPEAKER(+)
RADIO - C2 5 X54 18VT RIGHT FRONT SPEAKER(+)
6 X57 18BR/LB LEFT REAR SPEAKER(-)
7 X58 18DB/PK RIGHT REAR SPEAKER(-)
BLACK

1 2
1 L38 18BR/WT REAR FOG LAMP FEED -
REAR FOG LAMP 2 Z1 20BK GROUND
(BUILT-UP-EXPORT)
LIGHT GREEN
5 1 2 1 L22 20LG/DG HEADLAMP SWITCH FUSED OUTPUT
3 2 L95 18DG/YL REAR FOG LAMP RELAY CONTROL
3 Z1 20BK GROUND
L38 20BR/WT REAR FOG LAMP FEED
4 4
L38 20BR/WT REAR FOG LAMP FEED
REAR FOG 5 L22 20LG/DG HEADLAMP SWITCH FUSED OUTPUT
LAMP RELAY
(BUILT-UP-EXPORT)
WHITE

1 4
1 Z1 20BK GROUND
2 L95 18DG/YL REAR FOG LAMP RELAY CONTROL
3 L38 20BR/WT REAR FOG LAMP FEED
REAR FOG
LAMP SWITCH
(BUILT-UP-EXPORT)
RHD
TJI08033 J998W-5
BLACK

A B A V20 18VT/OR REAR WASHER MOTOR CONTROL
B Z1 18BK GROUND
REAR WASHER
PUMP
(HARD TOP)
GRAY
1 Z1 20BK GROUND
1 4 2 C80 20DB/LG REAR WINDOW DEFOGGER SWITCH SENSE
3 F81 20DB/RD FUSED REAR WINDOW DEFOGGER RELAY OUTPUT
REAR WINDOW 4 E2 20OR FUSED PANEL LAMPS DIMMER SWITCH SIGNAL
DEFOGGER
SWITCH
(HARD TOP)
BLACK
1 V23 18BR/PK FUSED IGNITION SWITCH OUTPUT (RUN)
3 V13 18BK/LG REAR WIPER MOTOR CONTROL
REAR WIPER
MOTOR
(HARD TOP)
WHITE
1 Z1 18BK/WT GROUND
1 2 2 V20 18VT/OR REAR WASHER MOTOR CONTROL
3 6 3 E2 20OR FUSED PANEL LAMPS DIMMER SWITCH SIGNAL
4 V13 18BR/LG REAR WIPER MOTOR CONTROL
5 V23 18BR/PK FUSED IGNITION SWITCH OUTPUT (RUN)
REAR WIPER/
6 - -
WASHER SWITCH
(HARD TOP)
J998W-5 TJI08034
BLACK
1 2 Z1 20BK GROUND
RIGHT CITY
LAMP
(BUILT-UP-EXPORT)
BLACK

2 1 1 M1 20PK/WT FUSED B(+)
RIGHT
COURTESY
LAMP
BLACK

1 Z1 18BK GROUND
2 L39 18LB FOG LAMP RELAY NO. 1 OUTPUT
RIGHT FOG
LAMP
(EXCEPT BUILT-UP
-EXPORT)
BLACK
1 3
1 L60 18TN RIGHT TURN SIGNAL
RIGHT FRONT PARK/ 2 L7 18BK/YL HEADLAMP SWITCH OUTPUT
TURN SIGNAL LAMP 3 Z1 18BK GROUND
(EXCEPT BUILT-UP
-EXPORT)
BLACK
1 2 1 X54 18VT RIGHT FRONT SPEAKER (+)
2 X56 18DB RIGHT FRONT SPEAKER (-)
RIGHT FRONT
SPEAKER
BLACK
1 3
RIGHT FRONT TURN 2 - -
SIGNAL LAMP 3 Z1 18BK GROUND
(BUILT-UP-EXPORT)
TJI08035 J998W-5
BLACK

2 1
1 B6 18WT/DB RIGHT FRONT WHEEL SPEED SENSOR (-)
2 B7 18WT RIGHT FRONT WHEEL SPEED SENSOR (+)
RIGHT FRONT
WHEEL SPEED
SENSOR
2 BLACK

1 3 1 L3 16RD/OR DIMMER SWITCH HIGH BEAM OUTPUT
3 Z1 18BK GROUND
RIGHT
HEADLAMP
BLACK

1 L22 20LG/DG HEADLAMP SWITCH FUSED OUTPUT
RIGHT HEADLAMP
3 Z1 18BK GROUND
LEVELING MOTOR
(BUILT-UP-EXPORT)
GRAY
1 2

2 Z1 20BK GROUND
RIGHT LICENSE
LAMP
(BUILT-UP-EXPORT)

1
1 2 L62 18BR/RD RIGHT TURN SIGNAL
L62 18BR/RD RIGHT TURN SIGNAL
2
3 4 L1 20VT/BK BACK-UP LAMP FEED
3
L50 18WT/TN BRAKE LAMP SWITCH OUTPUT
RIGHT REAR
LAMP ASSEMBLY L63 18DG/RD LEFT TURN SIGNAL
4
BLACK

1 2 1 X52 20DB/WT RIGHT REAR SPEAKER (+)
2 X58 20DB/PK RIGHT REAR SPEAKER (-)
RIGHT REAR
SPEAKER
(SOUND BAR)
BUILT-UP-EXPORT
J998W-5 TJI08036
BLACK

2 1
1 B1 18YL/DB RIGHT REAR WHEEL SPEED SENSOR (-)
2 B2 18YL RIGHT REAR WHEEL SPEED SENSOR (+)
RIGHT REAR
WHEEL SPEED
SENSOR
GRAY

1 1 L60 18TN RIGHT TURN SIGNAL
2 Z1 18BK GROUND
RIGHT REPEATER
LAMP
(BUILT-UP-EXPORT)
GRAY

RIGHT SIDE
MARKER LAMP
(EXCEPT BUILT-
UP-EXPORT)
BLACK
2 1
1 G10 20LG/RD SEAT BELT SWITCH SENSE
2 Z1 20BK GROUND
SEAT BELT
SWITCH
(EXCEPT LHD BUILT-
-UP-EXPORT)

1 F34 20TN/BK FUSED B(+)
2 Z1 20BK GROUND
1 6 3 F15 20DB FUSED IGNITION OUTPUT (ST-RUN)
4 Z12 20BK/LB GROUND
5 D2 20WT/BK CCD BUS(-)
SENTRY KEY
IMMOBILIZER
MODULE
BLACK

1 2
SOUND BAR 2 M2 20YL COURTESY LAMPS DRIVER
DOME LAMP
TJI08037 J998W-5
NATURAL
2 K22 18OR/DB THROTTLE POSITION SENSOR SIGNAL
THROTTLE 3 K7 20OR 5V SUPPLY
POSITION
SENSOR
BLACK

B A A F12 20RD/LG FUSED IGNITION SWITCH OUTPUT (ST-RUN)
B T23 18OR/LG TRANSMISSION LOW/OVERDRIVE SOLENOID
TORQUE CONVERTOR
CLUTCH SOLENOID
BLACK

A B A G107 20BK/RD 4WD SENSE
B Z1 20BK GROUND
TRANSFER
CASE SWITCH

BLACK 1 L60 18TN RIGHT TURN SIGNAL
2 L50 18WT/TN BRAKE LAMP SWITCH OUTPUT
3 L62 18BR/RD RIGHT TURN SIGNAL
4 L32 16PK COMBINATION FLASHER OUTPUT
6 1 5 L5 20BK/GY FUSED IGNITION SWITCH OUTPUT (RUN-ACC)
11 7 6 L9 16BK/WT FUSED FLASHER FEED
7 - -
8 - -
TURN SIGNAL/ 9 L63 18DG/RD LEFT TURN SIGNAL
HAZARD SWITCH 10 L61 18GY LEFT TURN SIGNAL
11 L55 16RD/WT COMBINATION FLASHER INPUT
BLACK

2 1
1 Z1 18BK GROUND
UNDERHOOD
LAMP
J998W-5 TJI08038

4 1 1 V36 18TN/RD SPEED CONTROL VACUUM SOLENOID CONTROL
2 V35 18LG/RD SPEED CONTROL VENT SOLENOID CONTROL
3 V30 20DB/RD SPEED CONTROL BRAKE SWITCH OUTPUT
4 Z1 18BK GROUND
VEHICLE SPEED
CONTROL
SERVO
BLACK

1 K6 20VT/OR 5V SUPPLY
3 1
3 G7 20WT/OR VEHICLE SPEED SENSOR SIGNAL
VEHICLE SPEED
SENSOR
BLACK

A B A V10 18BR WASHER PUMP CONTROL SWITCH OUTPUT
B Z1 18BK GROUND
WINDSHIELD
WASHER PUMP
BLACK
1 V6 18PK/BK FUSED IGNITION SWITCH OUTPUT (RUN-ACC)
2 V5 18DG/YL WIPER PARK SWITCH SENSE
3 1 3 - -
5 V3 18BR/WT LOW SPEED WIPER SWITCH OUTPUT
WINDSHIELD 6 V4 18RD/YL WIPER SWITCH HIGH SPEED OUTPUT
WIPER MOTOR
NATURAL
1 Z1 20BK GROUND
2 V5 18DG/YL WIPER PARK SWITCH SENSE
3 V10 18BR WASHER PUMP CONTROL SWITCH OUTPUT
6 1
4 V3 18BR/WT LOW SPEED WIPER SWITCH OUTPUT
5 V6 18PK/BK FUSED IGNITION SWITCH OUTPUT (RUN-ACC)
WINDSHIELD 6 V4 18RD/YL WIPER SWITCH HIGH SPEED OUTPUT
WIPER SWITCH
TJI08039 J998W-5
TJ 8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 1
8W-90 CONNECTOR/GROUND LOCATIONS

DESCRIPTION AND OPERATION each section for connector number identification.
Refer to the index for the proper figure number.
INTRODUCTION
This section provides illustrations identifying com- CONNECTOR/GROUND LOCATIONS
ponent and connector locations in the vehicle. A con- For items that are not shown in this section a N/S
nector index is provided. Use the wiring diagrams in is placed in the Fig. column.
Connector Color Location Fig. Connector Color Location Fig.

Name/Number Name/Number
A/C BK At A/C 12 C103 BK Near T/O for 2, 3
Compressor Compressor Fuel Injector
Clutch Clutch NO. 6
A/C Heater BK Rear of Blower 17, 18 C104 (LHD) GY Rear of Engine 2
Control - C1 Motor Switch C104 (RHD) BK Rear of Engine 3
A/C Heater BK Rear of Lamp 17, 18 C106 (LHD) BK Left Kick Panel 2, 15
Control - C2
C106 (RHD) BK Right Kick 16
A/C Heater BK Rear of A/C 17, 18 Panel
Control - C3 Heater Control
C107 (LHD) YL Left Kick Panel 2, 15
Switch
C107 (RHD) YL Right Kick 16
A/C High BK On A/C 12
Panel
Pressure Switch Compressor
C108 (LHD) BL Left Kick Panel 2, 15
A/C Low GY Near T/O for N/S
Pressure Switch Powertrain C108 (RHD) BL Right Kick 16
Control Module Panel
ABS Diode BK Near T/O for 2 C110 BK Left Fender 3, 5
Controller Side Shield
Anti-Lock Brake C154 BK Top Right Side 11, 14
ABS Pump BK Left Side of 6 of Transmission
Motor Engine C170 LT Right Kick 2, 17,
Compartment GY/ Panel 18
Near Grommet BK
Airbag Control YL Front of Floor 15, 16, C180 BK Engine N/S
Module Pan Tunnel 19 Compartment
Back-up Lamp BK Right Side of 14 Left Side
Switch (M/T) Transmission C202 (LHD) GY Left Kick Panel 15, 17
Battery BK Under Battery 3, 4 C202 (RHD) GY Right Kick 16, 18
Temperature Tray Panel
Sensor
C203 (LHD) GN Left Kick Panel 15, 17
Brake Lamp GY Top of Brake 15, 16
C203 (RHD) GN Right Kick 16, 18
Switch Pedal Bracket
Panel
Brake Shift WT Near Steering 20
C204 (LHD) RD Left Kick Panel 15, 17
Interlock Column
Solenoid C204 (RHD) RD Right Kick 16, 18
Panel
Brake Warning BK On Brake 2, 3
Indicator Switch Master Cylinder C322 BK Left Kick Panel 15, 16,
22
C323 (LHD) RD Left Kick Panel 15, 22
8W - 90 - 2 8W - 90 CONNECTOR/GROUND LOCATIONS TJ

C323 (RHD) LT GY Left Kick Panel 16 Data Link BK Bottom Left of 17
C325 (4 Spkr WT/ Left Side of 22, 23 Connector Instrument
Sys) BK Sound Bar (LHD) Panel
C326 (Hard BK Left Rear 22, 23 Data Link BK Bottom Right of 18
Top) Quarter Panel Connector Instrument
(RHD) Panel
C329 (LHD) BK Left Side of 24
Rear Bumper Daytime BK Left Side of 4
Running Lamp Engine
C329 (RHD) BK Right Side of 25
Module (Except Compartment
Rear Bumper
Built-Up-Export)
C330 (4 Spkr WT/ Left Side of 22, 23
Driver Door Ajar NAT At 9A9 Pillar 15, 16
Sys) BK Sound Bar
Switch
C331 (Hard BK Left Rear 22, 23
Duty Cycle BK Left Fender 5
Top) Quarter Panel
Evap/Purge Side Shield
Camshaft GY Below 11 solenoid
Position Sensor Distributor
Engine Coolant BK On Thermostat 9, 10
Cigar Lighter/ BK Bottom of 15, 22 Temperature Housing
Accessory Instrument Sensor
Relay (LHD) Panel Near
Engine Oil BK Right Side of 11
Steering
Pressure Engine Block
Column
Sensor
Cigar Lighter/ BK Bottom of N/S
Fog Lamp BK Near Fuse 15
Accessory Instrument
Relay NO.1 Block T/O
Relay (RHD) Panel Near
(Except
Steering
Built-Up-Export)
Column
Fog Lamp BK Near Fuse 15
Cigar Lighter/ RD Rear of Cigar 17, 18
Relay NO.2 Block T/O
Power Outlet Lighter
(Except
Clockspring - YL Rear of 20 Built-Up-Export)
C1 Clockspring
Front Fog Lamp BK At Switch 17
Clockspring - NAT Rear of 20 Switch (Except
C2 Clockspring Built-Up-Export)
Clutch Pedal BK Top of Clutch 15, 16 Fuel Injector BK At Injector 9, 10
Position Switch Pedal Bracket NO.1
(M/T)
Fuel Injector BK At Injector 9, 10
Combination BK Bottom of 20 NO.2
Flasher Instrument
Fuel Injector BK At Injector 9, 10
Panel Near
NO.3
Steering
Column Fuel Injector BK At Injector 9, 10
NO.4
Controller GY Near Grommet 2, 19
Anti-Lock Brake Rear Left Side Fuel Injector BK At Injector 10
- C1 of Dash Panel NO.5
Controller GY Near Grommet 2, 19 Fuel Injector BK At Injector 10
Anti-Lock Brake Rear Left Side NO.6
- C2 of Dash Panel Fuel Pump BK Above Fuel 1
Crankshaft BK At Rear of 9, 10, Module Tank
Position Sensor Intake Manifold 13

G100 Rear Center of 2, 3 G Switch BK Near T/O for 19
Engine Controller
Compartment Anti-Lock Brake
G101 Rear Center of 2 Generator BK Rear of 12
Engine Generator
Compartment Headlamp BK At Steering 20
G102 Left Radiator 5 Dimmer Switch Column Part of
Closure Panel Multifunction
G103 Right Radiator 1 Switch
Closure Panel Headlamp BK Right Side of 17, 18
G104 Rear of 12 Leveling Switch Instrument
Generator (Built-Up- Panel
Export)
G105 Right Rear of 12
Engine Block Headlamp BK Rear of Switch 17, 18
Switch
Engine Block High Note Horn BK Left Front 5
Fender Side
Shield
Engine Block
HVAC Unit GY Bottom Right of 21
G200 Right Rear of 17, 18
(LHD) Instrument
Instrument
Panel
Panel
HVAC Unit GY Bottom Left of 18
G201 Right Rear of 17, 18
(RHD) Instrument
Instrument
Panel
Panel
Hydraulic BK Left Side of 6
G202 (LHD) Right Rear of 21
Control Unit Engine
Instrument
Compartment
Panel
Idle Air Control BK Side of Throttle 9, 10
G202 (RHD) Left Rear of 18
Motor Body
Instrument
Panel Ignition Coil GY Near Generator 12
G203 (LHD) Right Rear of 21 Ignition Switch GY Rear of Ignition 20
Instrument Switch
Panel Instrument GN Rear of Cluster 17, 18
G203 (RHD) Left Rear of 18 Cluster - C1
Instrument Instrument BL Rear of Cluster 17, 18
Panel Cluster - C2
G300 (LHD) Left Kick Panel 15 Intake Air GY Rear of Intake 9, 10
G300 (RHD) Right Kick 16 Temperature Manifold
Panel Sensor
G301 (LHD) Right Kick 15 Key-In Switch GN At Key-In 20
Panel Switch
G301 (RHD) Left Kick Panel 16 Leak Detection BK Engine N/S
Pump (Except Compartment
G302 (LHD) Left Kick Panel 15
Built-Up-Export) Left Side
G302 (RHD) Right Kick 16
Left City Lamp BK At Lamp 5
Panel
(Built-Up-
Export)

Left Courtesy BK Left Side of 17, 18 Low Note Horn BK Left Front 5
Lamp Instrument (Except Fender Side
Panel Built-Up-Export) Shield
Left Fog Lamp BK At Lamp N/S Manifold BK Side of Throttle 9, 10
(Except Absolute Body
Built-Up-Export) Pressure
Left Front BK At Lamp N/S Sensor
Park/Turn Oxygen Sensor GY On Front 9, 10
Signal Lamp 1/1 Upstream Exhaust Pipe
(Except Oxygen Sensor BK Rear of 14
Built-Up-Export) 1/2 Downstream Catalytic
Left Front BK At Speaker 17, 18 Converter
Speaker Park/Neutral BK Left of 11
Left Front Turn BK At Lamp N/S Position Switch Transmission
Signal Lamp (A/T)
(Built-Up- Passenger YL Rear of Airbag 15, 16,
Export) Airbag 18, 21
Left Front BK Left Side of 6 Passenger LT GY Near Fuse 15, 16
Wheel Speed Engine Airbag On/Off Block T/O
Sensor Compartment Switch - C1
Near Hydraulic
Passenger YL Near Fuse 15, 16
Control Unit
Airbag On/Off Block T/O
Left Headlamp BK Rear of Lamp 5 Switch - C2
Left Headlamp BK At Lamp 5 Passenger Door BK Near T/O for 15, 16
Leveling Motor Ajar Switch G301
(Built-Up-
Power Steering BK Near Power 9
Export)
Pressure Switch Steering Pump
Left License GY At Lamp 24, 25 (2.5L)
Lamp
Powertrain BK Left Rear of 3, 4
(Built-Up-
Control Module Engine
Export)
- C1 Compartment
Left Rear Lamp BK At Lamp 24, 25
Powertrain WT Left Rear of 3, 4
Assembly
Left Rear BK At Sound Bar N/S - C2 Compartment
Speaker (Sound
Powertrain GY Left Rear of 3, 4
Bar)
Left Rear Wheel BK Near Vehicle 1 - C3 Compartment
Speed Sensor Speed Sensor
PRNDL Lamp BK Rear of Lamp 15, 16
T/O
Radio - C1 GY Rear of Radio 17, 18
Left Repeater GY At Lamp N/S
Lamp Radio - C2 BK Rear of Radio 17, 18
(Built-Up- Rear Fog Lamp BK At Lamp 24, 25
Export) (Built-Up-
Left Side GY At Lamp N/S Export)
Marker Lamp Rear Fog Lamp LT GN Near Fuse N/S
(Except Relay Block T/O
Built-Up-Export) (Built-Up-
Export) (LHD)

Rear Fog Lamp LT GN Near Fuse 16 Right License GY At Lamp 24, 25
Relay Block T/O Lamp
(Built-Up- (Built-Up-
Export) (RHD) Export)
Rear Fog Lamp WT At Switch 17, 18 Right Rear BK At Lamp 24, 25
Switch Lamp Assembly
(Built-Up- Right Rear BK At Sound Bar N/S
Export) Speaker (Sound
Rear Washer BK Under Washer 5 Bar)
Pump (Hard Fluid Reservoir Right Rear BK Near Vehicle 1
Top) Wheel Speed Speed Sensor
Rear Window GY Behind Rear 17, 18 Sensor T/O
Defogger Switch Window Right Repeater GY At Lamp 1
(Hard Top) Defogger Lamp
Switch (Built-Up-
Rear Wiper BK At Rear Wiper N/S Export)
Motor (Hard Motor Right Side GY At Lamp 1
Top) Marker Lamp
Rear Wiper/ WT Behind Rear 17, 18 (Except
Washer Switch Wiper/Washer Built-Up-Export)
(Hard Top) Switch Seat Belt Switch BK Near Park 22, 23
Right City Lamp BK At Lamp 1 (Except LHD Brake Switch
(Built-Up- Built-Up-Export) T/O
Export) Sentry Key BK At Immobilizer 15, 16
Right Courtesy BK Right Side of 18, 21 Immobilizer
Lamp Instrument Module
Panel Sound Bar BK At Sound Bar N/S
Right Fog Lamp BK At Lamp 1 Dome Lamp
(Except Throttle Position NAT Side of Throttle 9, 10
Built-Up-Export) Sensor Body
Right Front BK At Lamp 1 Torque BK Left Side of N/S
Park/Turn Converter Transmission
Signal Lamp Clutch Solenoid
(Except
Transfer Case BK Left Side of 14
Built-Up-Export)
Switch Transfer Case
Right Front BK At Speaker 18, 21
Turn Signal/ BK At Steering 20
Speaker
Hazard Switch Column Part of
Right Front Turn BK At Lamp 1 Multifunction
Signal Lamp Switch
(Built-Up-
Underhood BK Under Hood 2, 3
Export)
Lamp
Right Front BK Rear of Engine 13
Vehicle Speed BK Left Side of N/S
Wheel Speed
Control Servo Engine
Sensor
(LHD) Compartment
Right Headlamp BK Rear of Lamp 1
Vehicle Speed BK Right Side of N/S
Right Headlamp BK Near Lamp at 1 Control Servo Engine
Leveling Motor Motor (RHD) Compartment
(Built-Up-
Vehicle Speed BK Left Rear of 14
Export)
Sensor Transfer Case

Windshield BK Under Washer 5 Windshield NAT At Steering 20
Washer Pump Fluid Reservoir Wiper Switch Column
Windshield BK Center of Cowl 7, 8
Wiper Motor Panel
Fig. 1 Front End Wiring Connectors

Fig. 2 Engine Compartment Connectors — Rear, LHD

Fig. 3 Engine Compartment Connectors — Rear, RHD

Fig. 4 Engine Compartment Connectors—LHD

Fig. 5 Engine Compartment Connectors—Front Side

Fig. 6 ABS Hydraulic Control Unit
Fig. 7 Windshield Wiper Motor—LHD

Fig. 8 Windshield Wiper Motor—RHD

Fig. 9 Engine Harness Connectors—2.5L Engine

Fig. 10 Engine Harness Connectors—4.0L Engine

Fig. 11 Engine and Automatic Transmission Connectors

Fig. 12 Engine Grounds

Fig. 13 Crankshaft Position Sensor and Right Front Wheel Speed Sensor
Fig. 14 Transmission and Transfer Case Connectors

Fig. 15 Dash Panel Connectors—LHD

Fig. 16 Dash Panel Connectors—RHD

Fig. 17 Instrument Panel Wiring Connectors—LHD

Fig. 18 Instrument Panel Wiring Connectors—RHD

Fig. 19 Airbag Control Module and Controller, Antilock Brakes—LHD

Fig. 20 Steering Column Connectors

Fig. 21 Instrument Panel Connectors—Right Side, LHD

Fig. 22 Body Connectors—LHD

Fig. 23 Rear Body Wiring Connectors—RHD

Fig. 24 Rear Under Body Wiring Connectors—LHD
Fig. 25 Rear Under Body Wiring Connectors—RHD

TJ 8W - 95 SPLICE LOCATIONS 8W - 95 - 1
8W-95 SPLICE LOCATIONS

DESCRIPTION AND OPERATION section for splice number identification. Refer to the
index for proper splice number.
INTRODUCTION
This section provides illustrations identifying the SPLICE LOCATIONS
general location of the splices in this vehicle. A splice For splices that are not shown in the figures in
index is provided. Use the wiring diagrams in each this section, an N/S is placed in the Fig. column.
Splice Location Fig. Splice Location Fig.

Number Number
S101 Near T/O for Powertrain 2 S119 Left Side Radiator Closure 1
(LHD) Control Module Panel
S101 Near T/O for Power 3 S122 Near T/O for Left Front Turn N/S
(RHD) Distribution Center (Built-Up- Signal Lamp At Grommet
S102 Near T/O for G100 2, 3 Export)
S103 Near T/O for G101 2 S122 Near T/O for Left Front N/S
(LHD) (Except Park/Turn Signal Lamp
Built-Up-
S103 Near T/O for Battery 3
Export)
(RHD) Temperature Sensor
S123 Near T/O for G105 6
S104 Near T/O for C110 2
(LHD)
S105 Near Grommet on Left Side 2
S123 Near T/O for C103 N/S
(LHD) of Dash Panel
(2.5L)
S105 Near T/O for C110 3 (RHD)
(RHD)
S123 Near T/O for Fuel Injector 7
S106 Near T/O for Ground G100 2 (4.0L) NO. 6
S107 Near T/O for G101 2 (RHD)
S108 Near T/O for Underhood 2 S124 Near T/O for G105 6
(LHD) Lamp (LHD)
S108 Near T/O for C110 3 S124 Near T/O for C103 N/S
(RHD) (RHD)
S109 Near T/O for C103 and C104 2 S125 Near T/O for Right Front N/S
(Built-Up- Turn Signal Lamp At
S110 Near T/O for C103 and C104 2
Export) Grommet
S112 Near Controller Antilock 2
S125 Near T/O for Right Front N/S
Brake
(Except Park/Turn Signal Lamp At
S114 Near ABS Pump Motor T/O 2 Built-Up- Grommet
S115 Near T/O for Duty Cycle 1 Export)
(Except Evap/Purge Solenoid S126 Near T/Os for Fuel Injectors 6
Built-Up- (LHD)
Export)
S116 Near T/O for High Note Horn 1 (2.5L) NO. 4
(Except (RHD)
Built-Up-
Export)
(4.0L) NO. 6
S117 Near T/O for Windshield 1 (RHD)
Washer Pump Motor
S127 Near T/O for Idle Air Control 4, 5
S118 Near Left Headlamp T/O 1 Motor
8W - 95 - 2 8W - 95 SPLICE LOCATIONS TJ

Number Number
S127 Between Fuel Injector NO. 2 5 S144 Near T/O for Right Front N/S
(2.5L) and Fuel Injector NO. 3 Park/Turn Signal Lamp
(RHD) S146 Near T/O for Powertrain 2
S128 Between Fuel Injector NO. 2 4, 5 Control Module
and Fuel Injector NO. 3 S147 Near T/O for Powertrain 2
S129 Near T/O for Fuel Injectors 6 (LHD) Control Module
(LHD) S147 Right Side of Engine 3
S129 Near T/O for C104 7 (RHD) Compartment Near Grommet
(RHD) S150 Near T/O for Right Headlamp 1
S130 Near T/O for Fuel Injectors 6 (Built-Up- Leveling Motor
(LHD) Export)
S130 Near T/O for C103 N/S S151 Near T/O for Left Headlamp 1
(RHD) (Built-Up- Ground
S131 Near T/O for ABS Pump 2 Export)
(LHD) Motor S202 Center Rear of Instrument 10, 11
S131 Near T/O for C110 3 Panel
(RHD) S204 Center Rear of Instrument 10, 11
S132 Near T/O for Oxygen Sensor 6, 7 Panel
1/2 Downstream S206 Center Rear of Instrument 10, 11
S133 Near T/O for G105 6 Panel
(LHD) S207 Near Cigar Lighter T/O 10, 11
S133 Near T/O For C104 7 S301 Near Grommeted T/O to 8
(RHD) (LHD) Windshield Wiper Motor
S134 Near T/O for Oxygen Sensor 6, 7 S301 Near T/O for Passenger 9
1/2 Downstream (RHD) Airbag
S135 Near T/O for Oxygen Sensor 6, 7 S302 Near Grommeted T/O for 8, 9
1/2 Downstream Windshield Wiper Motor
S136 In Battery Harness Near N/S S303 Near Grommeted T/O for 8, 9
PDC Windshield Wiper Motor
S138 Near T/O for Right Headlamp 1 S304 Near Grommeted T/O for 8, 9
(Built-Up- Leveling Motor Windshield Wiper Motor
Export) S306 Near T/O for Airbag Control 8, 9
S141 Near T/O for Left Front Turn N/S Module
(Built-Up- Signal Lamp S307 Near T/O for Airbag Control 8, 9
Export) Module
S141 Near T/O for Left Front N/S S309 Front of Left Rear Wheel 12, 13
(Except Park/Turn Signal Lamp Well
Built-Up-
S310 Left Rear Quarter Panel, 12, 13
Export)
Near Body Grommet
S311 Near Left Tail Lamp 12, 13
(Built-Up- Turn Signal Lamp At
Connector
Export) Grommet
S313 Front of Left Rear Wheel 12, 13
Well
(Except Park/Turn Signal Lamp at
Built-Up- Grommet S314 Front of Left Rear Wheel 12, 13
Export) Well
S143 Near T/O for Left Front N/S S315 Near Right Tail Lamp 12, 13
Park/Turn Signal Lamp Connetor

Number Number
S316 In T/O for Rear Fog Lamp 12, 13 S331 Near T/O for Airbag Control 8, 9
S317 Near T/O for Left License 12, 13 Module
Lamp S332 Near T/O for Cigar 8, 9
S320 Near T/O for 100 way 8 Lighter/Accessory Relay
(LHD) Connector S335 Near Left Tail Lamp 12
S320 Near Passenger Airbag 9 Connector
(RHD) On/Off Switch S400 Near T/O for Rear Window N/S
S330 In T/O for Fuse Block 8 Defogger Feed
(LHD) S401 Near T/O for Rear Window N/S
S330 Near Passenger Airbag 9 Defogger Feed
(RHD) On/Off Switch
Fig. 1 Engine Compartment Splices—Front

Fig. 2 Engine Compartment Splices—Rear,LHD

Fig. 3 Engine Compartment Splices—Rear,RHD

Fig. 4 Engine Wiring Splices—LHD

Fig. 5 Engine Wiring Splices—RHD

Fig. 6 Engine Wiring Splices—LHD

Fig. 7 Engine Wiring Splices—RHD

Fig. 8 Dash Panel Wiring Splices—LHD

Fig. 9 Dash Panel Wiring Splices—RHD

Fig. 10 Instrument Panel Wiring Splices—LHD

Fig. 11 Instrument Panel Wiring Splices—RHD

Fig. 12 Body Wiring Splices—LHD

Fig. 13 Body Wiring Splices—RHD

TJ BATTERY 8A - 1
BATTERY
CONTENTS
page page
DESCRIPTION AND OPERATION REMOVAL AND INSTALLATION

BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DIAGNOSIS AND TESTING SPECIFICATIONS
BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SERVICE PROCEDURES
BATTERY CHARGING . . . . . . . . . . . . . . . . . . . . 13
DESCRIPTION AND OPERATION Rapid loss of electrolyte can be caused by an over-

charging condition. Be certain to diagnose the charg-
BATTERY ing system before returning the vehicle to service.
Refer to Charging System in the Diagnosis and
DESCRIPTION Testing section of Group 8C - Charging System for
A large capacity, low-maintenance storage battery more information.
is standard factory-installed equipment on this The factory-installed battery also has a built-in
model. This battery is designed to provide a safe, effi- test indicator (hydrometer). The color visible in the
cient and reliable means of storing electrical energy sight glass of the indicator will reveal the battery
in a chemical form. This means of energy storage condition. Refer to Built-In Test Indicator in the
allows the battery to produce the electrical energy Diagnosis and Testing section of this group for more
required to operate the engine starting system, as information.
well as to operate many of the other vehicle acces- This group covers only the battery diagnostic and
sory systems for limited durations while the engine service procedures. For battery maintenance sched-
and/or the charging system are not operating. ules and jump starting procedures, see the owner’s
The factory-installed low-maintenance bat- manual in the vehicle glove box, or refer to Mainte-
tery has removable battery cell caps. Water can nance Schedules and Jump Starting, Towing
be added to this battery. The battery is not sealed and Hoisting in Group 0 - Lubrication and Mainte-
and has vent holes in the cell caps (Fig. 1). The nance. While battery charging can be considered a
chemical composition within the low-maintenance maintenance procedure, battery charging information
battery reduces battery gassing and water loss, at is located in this group. This was done because the
normal charge and discharge rates. battery must be fully-charged before any diagnosis
can be performed.
Group 8A covers the Battery, Group 8B covers the
Starting Systems, and Group 8C covers the Charging
System. We have separated these systems to make it
easier to locate the information you are seeking
within this Service Manual. However, when attempt-
ing to diagnose any of these systems, it is important
that you keep their interdependency in mind.
The battery, starting, and charging systems in the
vehicle operate with one another, and must be tested
as a complete system. In order for the vehicle to start
and charge properly, all of the components that are
used in these systems must perform within specifica-
tions. It is important that the battery, starting, and
charging systems be thoroughly tested and inspected
any time a battery needs to be charged or replaced.
The cause of abnormal discharge, overcharging, or
Fig. 1 Low-Maintenance Battery - Typical early battery failure must be diagnosed and corrected
before a battery is replaced or returned to service.
8A - 2 BATTERY TJ
The diagnostic procedures used in each of these period. A battery must also be able to accept a
groups include the most basic conventional diagnostic charge, so that its voltage potential may be restored.
methods, to the more sophisticated On-Board Diag- In addition to producing and storing electrical
nostics (OBD) built into the Powertrain Control Mod- energy, the battery serves as a capacitor, or voltage
ule (PCM). Use of an induction-type milliampere stabilizer, for the electrical system of the vehicle. It
ammeter, volt/ohmmeter, battery charger, carbon pile absorbs most abnormal or transient voltages caused
rheostat (load tester), and 12-volt test lamp may be by the switching of any of the electrical components
required. in the vehicle.
All OBD-sensed systems are monitored by the The battery is vented to release excess hydrogen
PCM. Each monitored circuit is assigned a Diagnos- gas that is created when the battery is being charged
tic Trouble Code (DTC). The PCM will store a DTC in or discharged. However, even with these vents, the
electronic memory for any failure it detects. Refer to hydrogen gas can collect in or around the battery. If
On-Board Diagnostic Test For Charging System hydrogen gas is exposed to flame or sparks, it may
in the Diagnosis and Testing section of Group 8C - ignite.
Charging System for more information. If the electrolyte level is low, the battery may arc
internally and explode. If the battery is equipped
OPERATION with removable cell caps, add distilled water when-
The storage battery is a device used to store elec- ever the electrolyte level is below the top of the
trical energy potential in a chemical form. When an plates. If the battery cell caps cannot be removed, the
electrical load is applied to the battery terminals, an battery must be replaced if the electrolyte level
electrochemical reaction occurs within the battery. becomes low.
This reaction causes the battery to discharge electri-
cal current. BATTERY SIZE AND RATINGS
The battery is made up of six individual cells that The battery Group Size number, the Cold Cranking
are connected in series. Each cell contains positively Amperage (CCA) rating, and the Reserve Capacity
charged plate groups made of lead oxide, and nega- (RC) rating or Ampere-Hours (AH) rating can be
tively charged plate groups made of sponge lead. found on the original equipment battery label. Be
These dissimilar metal plates are submerged in a certain that a replacement battery has the correct
sulfuric acid and water solution called an electrolyte. Group Size number, as well as CCA, and RC or AH
As the battery discharges, a gradual chemical ratings that equal or exceed the original equipment
change takes place within each cell. The sulfuric acid specification for the vehicle being serviced.
in the electrolyte combines with the plate materials, Refer to Battery Classifications and Ratings in
causing both plates to slowly change to lead sulfate. the Specifications section of this group for more infor-
At the same time, oxygen from the positive plate mation. Battery sizes and ratings are discussed in
material combines with hydrogen from the sulfuric more detail below.
acid, causing the electrolyte to become mainly water.
The chemical changes within the battery are GROUP SIZE
caused by the movement of excess or free electrons The outside dimensions and terminal placement of
between the positive and negative plate groups. This the battery conform to standards established by the
movement of electrons produces a flow of electrical Battery Council International (BCI). Each battery is
current through the load device attached to the bat- assigned a BCI Group Size number to help identify a
tery terminals. correctly-sized replacement.
As the plate materials become more similar chem-
ically, and the electrolyte becomes less acid, the volt- COLD CRANKING AMPERAGE
age potential of each cell is reduced. However, by The Cold Cranking Amperage (CCA) rating speci-
charging the battery with a voltage higher than that fies how much current (in amperes) the battery can
of the battery, the battery discharging process is deliver for thirty seconds at -18° C (0° F). Terminal
reversed. voltage must not fall below 7.2 volts during or after
Charging the battery gradually changes the sul- the thirty second discharge period. The CCA required
fated lead plates back into sponge lead and lead is generally higher as engine displacement increases,
oxide, and the water back into sulfuric acid. This depending also upon the starter current draw
action restores the difference in the electron charges requirements.
deposited on the plates, and the voltage potential of
the battery cells. RESERVE CAPACITY
For a battery to remain useful, it must be able to The Reserve Capacity (RC) rating specifies the
produce high-amperage current over an extended time (in minutes) it takes for battery terminal volt-
age to fall below 10.5 volts, at a discharge rate of 25
TJ BATTERY 8A - 3
amperes. RC is determined with the battery fully- within this Service Manual. However, when attempt-
charged at 26.7° C (80° F). This rating estimates how ing to diagnose any of these systems, it is important
long the battery might last after a charging system that you keep their interdependency in mind.
failure, under minimum electrical load. The diagnostic procedures used in these groups
include the most basic conventional diagnostic meth-
AMPERE-HOURS ods, to the more sophisticated On-Board Diagnostics
The Ampere-Hours (AH) rating specifies the cur- (OBD) built into the Powertrain Control Module
rent (in amperes) that a battery can deliver steadily (PCM). Use of an induction-type milliampere amme-
for twenty hours, with the voltage in the battery not ter, volt/ohmmeter, battery charger, carbon pile rheo-
falling below 10.5 volts. This rating is also sometimes stat (load tester), and 12-volt test lamp may be
identified as the twenty-hour discharge rating. required.
All OBD-sensed systems are monitored by the
MOUNTING PCM. Each monitored circuit is assigned a Diagnos-
The battery is mounted in a stamped steel located tic Trouble Code (DTC). The PCM will store a DTC in
in the passenger side rear corner of the engine com- electronic memory for any failure it detects. Refer to
partment. A J-bolt is hooked through in the front and On-Board Diagnostic Test For Charging System
rear edges of the tray. A hold down strap fits across in the Diagnosis and Testing section of Group 8C -
the top of the battery case. The J-bolts pass through Charging System for more information.
the hold down strap on each side of the battery, and The battery must be completely charged and the
a nut secures the hold down strap to each of the top, posts, and terminal clamps should be properly
J-bolts. cleaned and inspected before diagnostic procedures
A plastic bubble-wrap style thermoguard slides are performed. Refer to Battery in the Removal and
over the battery case to enclose the sides of the bat- Installation section of this group for the proper bat-
tery. The thermoguard protects the battery from tery cleaning and inspection procedures. Refer to
engine compartment temperature extremes. Battery Charging in the Service Procedures section
The battery tray is secured with four screws to a of this group for the proper charging procedures.
support bracket mounted between the front fender
inner wheelhouse and the dash panel, rearward of WARNING:
the passenger side front wheel. • IF THE BATTERY SHOWS SIGNS OF FREEZ-
A hole in the bottom of the battery tray is fitted ING, LEAKING, LOOSE POSTS, OR LOW ELECTRO-
with a battery temperature sensor. Refer to Battery LYTE LEVEL, DO NOT TEST, ASSIST-BOOST, OR
Temperature Sensor in the Description and Opera- CHARGE. THE BATTERY MAY ARC INTERNALLY
tion section of Group 8C - Charging System for more AND EXPLODE. PERSONAL INJURY AND/OR VEHI-
information on this component. CLE DAMAGE MAY RESULT.
When installing a battery, be certain that the hold • EXPLOSIVE HYDROGEN GAS FORMS IN AND
down fasteners are tightened to the proper specifica- AROUND THE BATTERY. DO NOT SMOKE, USE
tions. Improper hold down fastener tightness, FLAME, OR CREATE SPARKS NEAR THE BATTERY.
whether too loose or too tight, can result in damage PERSONAL INJURY AND/OR VEHICLE DAMAGE
to the battery. Refer to Battery in the Removal and MAY RESULT.
Installation section of this group for the correct bat- • THE BATTERY CONTAINS SULFURIC ACID,
tery hold down fastener tightness specifications. WHICH IS POISONOUS AND CAUSTIC. AVOID CON-
TACT WITH THE SKIN, EYES, OR CLOTHING. IN
THE EVENT OF CONTACT, FLUSH WITH WATER
DIAGNOSIS AND TESTING AND CALL A PHYSICIAN IMMEDIATELY. KEEP OUT
OF THE REACH OF CHILDREN.
BATTERY • IF THE BATTERY IS EQUIPPED WITH REMOV-
ABLE CELL CAPS, BE CERTAIN THAT EACH OF
DIAGNOSIS THE CELL CAPS IS IN PLACE AND TIGHT BEFORE
The battery, starting, and charging systems oper- THE BATTERY IS RETURNED TO SERVICE. PER-
ate with one another, and must be tested as a com- SONAL INJURY AND/OR VEHICLE DAMAGE MAY
plete system. In order for the vehicle to start and RESULT FROM LOOSE OR MISSING CELL CAPS.
charge properly, all of the components involved in
these systems must perform within specifications. The condition of a battery is determined by two cri-
Group 8A covers the Battery, Group 8B covers the teria:
Starting Systems, and Group 8C covers the Charging 1. State-Of-Charge - This can be determined by
System. We have separated these systems to make it checking the specific gravity of the battery electrolyte
easier to locate the information you are seeking (built-in test indicator or hydrometer test), or by
8A - 4 BATTERY TJ
checking the battery voltage (open-circuit voltage A battery that will not accept a charge is faulty,
test). and must be replaced. Further testing is not
2. Cranking Capacity - This can be determined required. A fully-charged battery must be load tested
by performing a battery load test, which measures to determine its cranking capacity. A battery that is
the ability of the battery to supply high-amperage fully-charged, but does not pass the load test, is
current. faulty and must be replaced.
First, determine the battery state-of-charge. This
can be done in one of three ways. If the battery has a NOTE: Completely discharged batteries may take
built-in test indicator, view the test indicator to several hours to accept a charge. Refer to Battery
determine the state-of-charge. If the battery has no Charging - Charging A Completely Discharged Bat-
test indicator, but has removable cell caps, perform tery in the Service Procedures section of this group
the hydrometer test to determine the state-of-charge. for more information.
If the cell caps are not removable, or a hydrometer is
not available, perform the open-circuit voltage test to A battery is fully-charged when:
determine the state-of-charge. • All cells are gassing freely during charging.
The battery must be charged before proceeding • A green color is visible in the sight glass of the
with a load test if: built-in test indicator.
• The battery built-in test indicator has a black or • Three corrected specific gravity tests, taken at
dark color visible. one-hour intervals, indicate no increase in the spe-
• The temperature corrected specific gravity of the cific gravity.
battery electrolyte is less than 1.235. • Open-circuit voltage is 12.4 volts or greater.
• The battery open-circuit voltage is less than 12.4
volts.
TJ BATTERY 8A - 5
Battery Diagnosis
Condition Possible Causes Correction
The battery seems weak or 1. The battery has an 1. Refer to Battery in the Specifications section of
dead when attempting to start incorrect size or rating for this group. Replace an incorrect battery with the
the engine. this vehicle. correct battery.
2. The battery is physically 2. Inspect the battery for loose terminal posts or a
damaged. cracked and leaking case. Replace the battery, if
3. The battery terminal damaged.
connections are loose or 3. Refer to Voltage Drop Test in the Diagnosis
corroded. and Testing section of this group. Clean and
4. The battery is discharged. tighten the battery terminal connections, if
5. The electrical system required.
ignition-off draw is excessive. 4. Determine the battery state-of-charge. Refer to
6. The battery is faulty. Built-In Test Indicator, Hydrometer Test, or
7. The starting system is Open-Circuit Voltage Test in the Diagnosis and
faulty. Testing section of this group. Charge the battery,
8. The charging system is if required.
faulty. 5. Refer to Ignition-Off Draw Test in the Diagnosis
and Testing section of this group. Repair the
electrical system, if required.
6. Determine the battery cranking capacity. Refer
to Load Test in the Diagnosis and Testing section
of this group. Replace the battery, if required.
7. Determine if the starting system is performing
to specifications. Refer to Starting System in the
Diagnosis and Testing section of Group 8B -
Starting Systems for more information. Repair the
starting system, if required.
8. Determine if the charging system is performing
to specifications. Refer to Charging System in the
Diagnosis and Testing section of Group 8C -
Charging System for more information. Repair the
charging system, if required.
8A - 6 BATTERY TJ
Battery Diagnosis
Condition Possible Causes Correction
The battery state-of-charge 1. The battery has an 1. Refer to Battery in the Specifications section of
cannot be maintained. incorrect size or rating for this group. Replace an incorrect battery with the
this vehicle. correct battery.
2. The battery terminal 2. Refer to Voltage Drop Test in the Diagnosis
connections are loose or and Testing section of this group. Clean and
corroded. tighten the battery terminal connections, if
3. The generator drive belt is required.
slipping. 3. Refer to Accessory Drive Belt Diagnosis in the
4. The electrical system Diagnosis and Testing section of Group 7 -
ignition-off draw is excessive. Cooling System for more information. Replace or
5. The battery is faulty. adjust the generator drive belt, if required.
6. The starting system is 4. Refer to Ignition-Off Draw Test in the Diagnosis
faulty. and Testing section of this group. Repair the
7. The charging system is electrical system, if required.
faulty. 5. Determine the battery cranking capacity. Refer
8. Electrical loads exceed the to Load Test in the Diagnosis and Testing section
output of the charging of this group. Replace the battery, if required.
system. 6. Determine if the starting system is performing
9. Slow driving or prolonged to specifications. Refer to Starting System in the
idling with high-amperage Diagnosis and Testing section of Group 8B -
draw systems in use. Starting Systems for more information. Repair the
starting system, if required.
7. Determine if the charging system is performing
to specifications. Refer to Charging System in the
Diagnosis and Testing section of Group 8C -
Charging System for more information. Repair the
charging system, if required.
8. Inspect the vehicle for aftermarket electrical
equipment which might cause excessive electrical
loads.
9. Advise the vehicle operator, as required.
The battery will not accept a 1. The battery is faulty. 1. Refer to Battery Charging in the Service
charge. Procedures section of this group. Replace the
faulty battery, if required.
ABNORMAL BATTERY DISCHARGING 6. A faulty or incorrect charging system compo-

Any of the following conditions can result in abnor- nent. Refer to Charging System in the Diagnosis
mal battery discharging: and Testing section of Group 8C - Charging System
1. Corroded or loose battery posts and terminal for more information.
clamps. 7. A faulty or incorrect battery.
2. A loose or worn generator drive belt.
3. Electrical loads that exceed the output of the TESTING
charging system. This can be due to equipment
installed after manufacture, or repeated short trip BUILT-IN TEST INDICATOR
use. A test indicator (hydrometer) built into the top of
4. Slow driving speeds (heavy traffic conditions) or the battery case provides visual information for bat-
prolonged idling, with high-amperage draw systems tery testing (Fig. 2). Like a hydrometer, the built-in
in use. test indicator measures the specific gravity of the
5. A faulty circuit or component causing excessive electrolyte. The test indicator reveals the battery
ignition-off draw. Refer to Ignition-Off Draw Test state-of-charge; however, it will not reveal the crank-
in the Diagnosis and Testing section of this group for ing capacity of the battery. A load test must be per-
more information. formed to determine the battery cranking capacity.
TJ BATTERY 8A - 7
Refer to Load Test in the Diagnosis and Testing sec- tery, the battery must be load tested. Refer to Load
tion of this group for more information. Test in the Diagnosis and Testing section of this
group for more information.
• Black or Dark - indicates 0% to 75% state-of-
charge. The battery is inadequately charged and
must be charged until a green indication is visible in
the sight glass (12.4 volts or more), before the bat-
tery is tested further or returned to service. Refer to
Battery Charging in the Service Procedures section
of this group for more information. Also refer to
Abnormal Battery Discharging in the Diagnosis
and Testing section of this group for possible causes
of the discharged condition.
• Clear or Bright - indicates a low electrolyte
Fig. 2 Built-In Test Indicator level. The electrolyte level in the battery is below the
test indicator. A maintenance-free battery with non-
WARNING:
removable cell caps must be replaced if the electro-
• IF THE BATTERY SHOWS SIGNS OF FREEZ-
lyte level is low. Water must be added to a low-
ING, LEAKING, LOOSE POSTS, OR LOW ELECTRO-
maintenance battery with removable cell caps before
LYTE LEVEL, DO NOT TEST, ASSIST-BOOST, OR
it is charged. Refer to Battery Charging in the Ser-
CHARGE. THE BATTERY MAY ARC INTERNALLY
vice Procedures section of this group for more infor-
AND EXPLODE. PERSONAL INJURY AND/OR VEHI-
mation. A low electrolyte level may be caused by an
CLE DAMAGE MAY RESULT.
overcharging condition. Refer to Charging System
• EXPLOSIVE HYDROGEN GAS FORMS IN AND
in the Diagnosis and Testing section of Group 8C -
AROUND THE BATTERY. DO NOT SMOKE, USE
Charging System to diagnose an overcharging condi-
FLAME, OR CREATE SPARKS NEAR THE BATTERY.
tion.
PERSONAL INJURY AND/OR VEHICLE DAMAGE
MAY RESULT.
• THE BATTERY CONTAINS SULFURIC ACID,
WHICH IS POISONOUS AND CAUSTIC. AVOID CON-
AND CALL A PHYSICIAN IMMEDIATELY. KEEP OUT
• IF THE BATTERY IS EQUIPPED WITH REMOV-
THE CELL CAPS IS IN PLACE AND TIGHT BEFORE
THE BATTERY IS RETURNED TO SERVICE. PER-
SONAL INJURY AND/OR VEHICLE DAMAGE MAY
RESULT FROM LOOSE OR MISSING CELL CAPS.
Fig. 3 Built-In Test Indicator Sight Glass
Before testing, visually inspect the battery for any HYDROMETER TEST
damage (a cracked case or cover, loose posts, etc.)
The hydrometer test reveals the battery state-of-
that would cause the battery to be faulty. In order to
charge by measuring the specific gravity of the elec-
obtain correct indications from the built-in test indi-
trolyte. This test cannot be performed on
cator, it is important that the battery be level and
maintenance-free batteries with non-removable
have a clean sight glass. Additional light may be
cell caps. If the battery has non-removable cell caps,
required to view the indicator. Do not use open
refer to Built-In Test Indicator or Open-Circuit
flame as a source of additional light.
Voltage Test in the Diagnosis and Testing section of
To read the built-in test indicator, look into the
this group.
sight glass and note the color of the indicator (Fig. 3).
Specific gravity is a comparison of the density of
The battery condition that each color indicates is
the electrolyte to the density of pure water. Pure
described in the following list:
water has a specific gravity of 1.000, and sulfuric
• Green - indicates 75% to 100% state-of-charge.
acid has a specific gravity of 1.835. Sulfuric acid
The battery is adequately charged for further testing
makes up approximately 35% of the electrolyte by
or return to use. If the starter will not crank for a
weight, or 24% by volume.
minimum of fifteen seconds with a fully-charged bat-
8A - 8 BATTERY TJ
In a fully-charged battery the electrolyte will have
a temperature-corrected specific gravity of 1.260 to
1.290. However, a specific gravity of 1.235 or above is
satisfactory for battery load testing and/or return to
service.
WARNING:
MAY RESULT.
AND CALL A PHYSICIAN IMMEDIATELY. KEEP OUT Fig. 4 Hydrometer - Typical
as four points of specific gravity. For each 5.5° C
above 26.7° C (10° F above 80° F), add four points.
For each 5.5° C below 26.7° C (10° F below 80° F),
subtract four points. Always correct the specific grav-
ity for temperature variation. Test the specific grav-
ity of the electrolyte in each battery cell.
EXAMPLE: A battery is tested at -12.2° C (10° F)
Before testing, visually inspect the battery for any and has a specific gravity of 1.240. Determine the
damage (a cracked case or cover, loose posts, etc.) actual specific gravity as follows:
that would cause the battery to be faulty. Then (1) Determine the number of degrees above or
remove the cell caps and check the electrolyte level. below 26.7° C (80° F):26.6° C - -12.2° C = 38.8° C (80°
Add distilled water if the electrolyte level is below F - 10° F = 70° F)
the top of the battery plates. (2) Divide the result from Step 1 by 5.5 (10):38.8°
See the instructions provided by the manufacturer C 4 5.5 = 7 (70° F 4 10 = 7)
of the hydrometer for recommendations on the cor- (3) Multiply the result from Step 2 by the temper-
rect use of the hydrometer that you are using. ature correction factor (0.004):7 X 0.004 = 0.028
Remove only enough electrolyte from the battery cell (4) The temperature at testing was below 26.7° C
so that the float is off the bottom of the hydrometer (80° F); therefore, the temperature correction factor
barrel with pressure on the bulb released. is subtracted:1.240 - 0.028 = 1.212
The corrected specific gravity of the battery cell in
CAUTION: Exercise care when inserting the tip of this example is 1.212.
the hydrometer into a cell to avoid damaging the If the specific gravity of all cells is above 1.235, but
plate separators. Damaged plate separators can the variation between cells is more than fifty points
cause early battery failure. (0.050), the battery should be replaced. If the specific
gravity of one or more cells is less than 1.235, charge
To read the hydrometer correctly, hold it with the the battery at a rate of approximately five amperes.
top surface of the electrolyte at eye level (Fig. 4). Continue charging the battery until three consecu-
Hydrometer floats are generally calibrated to indi- tive specific gravity tests, taken at one-hour inter-
cate the specific gravity correctly only at 26.7° C (80° vals, are constant. If the cell specific gravity
F). When testing the specific gravity at any other variation is more than fifty points (0.050) at the end
temperature, a correction factor is required. of the charge period, replace the battery.
The correction factor is approximately a specific When the specific gravity of all cells is above 1.235,
gravity value of 0.004, which may also be identified and the cell variation is less than fifty points (0.050),
TJ BATTERY 8A - 9
the battery may be load tested to determine its (3) Using a voltmeter connected to the battery
cranking capacity. Refer to Load Test in the Diagno- posts (see the instructions provided by the manufac-
sis and Testing section of this group for more infor- turer of the voltmeter), measure the open-circuit volt-
mation. age (Fig. 5).
OPEN-CIRCUIT VOLTAGE TEST

A battery open-circuit voltage (no load) test will
show the state-of-charge of a battery. This test can be
used in place of the hydrometer test when a hydrom-
eter is not available, or for maintenance-free batter-
ies with non-removable cell caps.
WARNING:
• EXPLOSIVE HYDROGEN GAS FORMS IN AND Fig. 5 Testing Open-Circuit Voltage - Typical
FLAME, OR CREATE SPARKS NEAR THE BATTERY. See the Open-Circuit Voltage chart. This voltage
PERSONAL INJURY AND/OR VEHICLE DAMAGE reading will indicate the battery state-of-charge, but
MAY RESULT. will not reveal its cranking capacity. If a battery has
• THE BATTERY CONTAINS SULFURIC ACID, an open-circuit voltage reading of 12.4 volts or
WHICH IS POISONOUS AND CAUSTIC. AVOID CON- greater, it may be load tested to reveal its cranking
TACT WITH THE SKIN, EYES, OR CLOTHING. IN capacity. Refer to Load Test in the Diagnosis and
THE EVENT OF CONTACT, FLUSH WITH WATER Testing section of this group for more information.
AND CALL A PHYSICIAN IMMEDIATELY. KEEP OUT Open Circuit Voltage
• IF THE BATTERY IS EQUIPPED WITH REMOV- Open Circuit Volts Charge Percentage
ABLE CELL CAPS, BE CERTAIN THAT EACH OF 11.7 volts or less 0%
THE CELL CAPS IS IN PLACE AND TIGHT BEFORE 12.0 volts 25%
12.2 volts 50%
RESULT FROM LOOSE OR MISSING CELL CAPS. 12.4 volts 75%
12.6 volts or more 100%
Before proceeding with this test, completely charge
the battery. Refer to Battery Charging in the Ser-
vice Procedures section of this group for the proper LOAD TEST
battery charging procedures. A battery load test will verify the battery cranking
(1) Before measuring the open-circuit voltage, the capacity. The test is based on the Cold Cranking
surface charge must be removed from the battery. Amperage (CCA) rating of the battery. See the label
Turn on the head lamps for fifteen seconds, then affixed to the battery case, or refer to Battery Clas-
allow up to five minutes for the battery voltage to sifications and Ratings in the Specifications sec-
stabilize. tion of this group for the CCA rating of the factory-
(2) Disconnect and isolate both battery cables, neg- installed battery.
ative cable first.
8A - 10 BATTERY TJ
WARNING:
MAY RESULT.
Fig. 7 Volt-Ammeter-Load Tester Connections -
Typical
OF THE REACH OF CHILDREN. (3) Rotate the load control knob (carbon pile rheo-
• IF THE BATTERY IS EQUIPPED WITH REMOV- stat) to apply a 300 ampere load to the battery for
ABLE CELL CAPS, BE CERTAIN THAT EACH OF fifteen seconds, then return the control knob to the
THE CELL CAPS IS IN PLACE AND TIGHT BEFORE Off position (Fig. 8). This will remove the surface
THE BATTERY IS RETURNED TO SERVICE. PER- charge from the battery.
Before proceeding with this test, completely charge

the battery. Refer to Battery Charging in the Ser-
vice Procedures section of this group for the proper
battery charging procedures.
(1) Disconnect and isolate both battery cables, neg-
ative cable first. The battery top and posts should be
clean.
(2) Connect a suitable volt-ammeter-load tester
(Fig. 6) to the battery posts (Fig. 7). See the instruc-
tions provided by the manufacturer of the tester you
are using. Check the open-circuit voltage (no load) of
the battery. Refer to Open-Circuit Voltage Test in
the Diagnosis and Testing section of this group for Fig. 8 Remove Surface Charge from Battery -
the test procedures. The battery open-circuit voltage Typical
must be 12.4 volts or greater.
(4) Allow the battery to stabilize to open-circuit
voltage. It may take up to five minutes for the bat-
tery voltage to stabilize.
(5) Rotate the load control knob to maintain a load
equal to 50% of the CCA rating of the battery (Fig.
9). After fifteen seconds, record the loaded voltage
reading, then return the load control knob to the Off
position.
(6) The voltage drop will vary with the battery
temperature at the time of the load test. The battery
temperature can be estimated by using the ambient
temperature during the past several hours. If the
battery has been charged, boosted, or loaded a few
minutes prior to the test, the battery will be some-
what warmer. See the Load Test Temperature chart
for the proper loaded voltage reading.
Fig. 6 Volt-Ammeter-Load Tester - Typical
TJ BATTERY 8A - 11
MAY RESULT.
Fig. 9 Load 50% CCA Rating - Note Voltage - Typical ABLE CELL CAPS, BE CERTAIN THAT EACH OF
Load Test Temperature
Temperature SONAL INJURY AND/OR VEHICLE DAMAGE MAY
Minimum Voltage
°F °C RESULT FROM LOOSE OR MISSING CELL CAPS.
9.6 volts 70° and above 21° and above
The following operation will require a voltmeter
9.5 volts 60° 16° accurate to 1/10 (0.10) volt. Before performing the
9.4 volts 50° 10° tests, be certain the following procedures are accom-
9.3 volts 40° 4° plished:
• The battery is fully-charged. Refer to Battery
9.1 volts 30° -1° Charging in the Service Procedures section of this
8.9 volts 20° -7° group for more information.
8.7 volts 10° -12° • Fully engage the parking brake.
• If the vehicle is equipped with an automatic
8.5 volts 0° -18°
transmission, place the gearshift selector lever in the
Park position. If the vehicle is equipped with a man-
(7) If the voltmeter reading falls below 9.6 volts, at ual transmission, place the gearshift selector lever in
a minimum battery temperature of 21° C (70° F), the the Neutral position and fully depress the clutch
battery is faulty and must be replaced. pedal.
• Unplug the Automatic ShutDown (ASD) relay to
VOLTAGE DROP TEST prevent the engine from starting. The ASD relay is
The voltage drop test will determine if there is located in the Power Distribution Center (PDC). See
excessive resistance in the battery terminal connec- the label on the PDC for ASD relay identification and
tions or the battery cables. When performing these location.
tests, it is important to remember that the voltage (1) Connect the positive lead of the voltmeter to
drop is giving an indication of the resistance between the battery negative terminal post. Connect the neg-
the two points at which the voltmeter probes are ative lead of the voltmeter to the battery negative
attached. cable clamp (Fig. 10). Rotate and hold the ignition
Example: When testing the resistance of the bat- switch in the Start position. Observe the voltmeter. If
tery positive cable, touch the voltmeter leads to the voltage is detected, correct the poor contact between
battery positive cable clamp and the cable connector the cable clamp and the terminal post.
at the starter solenoid. If you probe the battery pos- (2) Connect the positive lead of the voltmeter to
itive terminal post and the cable connector at the the battery positive terminal post. Connect the nega-
starter solenoid, you are reading the combined volt- tive lead of the voltmeter to the battery positive cable
age drop in the battery positive cable clamp-to-termi- clamp (Fig. 11). Rotate and hold the ignition switch
nal post connection and the battery positive cable. in the Start position. Observe the voltmeter. If volt-
age is detected, correct the poor contact between the
WARNING: cable clamp and the terminal post.
• IF THE BATTERY SHOWS SIGNS OF FREEZ- (3) Connect the voltmeter to measure between the
ING, LEAKING, LOOSE POSTS, OR LOW ELECTRO- battery positive terminal post and the starter sole-
LYTE LEVEL, DO NOT TEST, ASSIST-BOOST, OR noid battery terminal stud (Fig. 12). Rotate and hold
8A - 12 BATTERY TJ
Fig. 12 Test Battery Positive Cable Resistance -

Typical
Fig. 10 Test Battery Negative Connection
Resistance - Typical
Fig. 13 Test Ground Circuit Resistance - Typical

to twenty-five milliamperes (0.005 to 0.025 ampere)
with the ignition switch in the Off position, and all
Fig. 11 Test Battery Positive Connection Resistance
non-ignition controlled circuits in proper working
- Typical
order. The twenty-five milliamperes are needed to
the ignition switch in the Start position. Observe the enable the memory functions for the Powertrain Con-
voltmeter. If the reading is above 0.2 volt, clean and trol Module (PCM), digital clock, electronically tuned
tighten the battery cable connection at the solenoid. radio, and other modules which may vary with the
Repeat the test. If the reading is still above 0.2 volt, vehicle equipment.
replace the faulty battery positive cable. A vehicle that has not been operated for approxi-
(4) Connect the voltmeter to measure between the mately twenty days, may discharge the battery to an
battery negative terminal post and a good clean inadequate level. When a vehicle will not be used for
ground on the engine block (Fig. 13). Rotate and hold twenty days or more (stored), remove the IOD fuse
the ignition switch in the Start position. Observe the from the Power Distribution Center (PDC). This will
voltmeter. If the reading is above 0.2 volt, clean and reduce battery discharging.
tighten the battery negative cable attachment on the Excessive IOD can be caused by:
engine block. Repeat the test. If the reading is still • Electrical items left on
above 0.2 volt, replace the faulty battery negative • Faulty or improperly adjusted switches
cable. • Faulty or shorted electronic modules and compo-
nents
IGNITION-OFF DRAW TEST • An internally shorted generator
The term Ignition-Off Draw (IOD) identifies a nor- • Intermittent shorts in the wiring.
mal condition where power is being drained from the If the IOD is over twenty-five milliamperes, the
battery with the ignition switch in the Off position. A problem must be found and corrected before replac-
normal vehicle electrical system will draw from five
TJ BATTERY 8A - 13
ing a battery. In most cases, the battery can be lowest milliampere scale of the multi-meter to check
charged and returned to service after the excessive the low-amperage IOD.
IOD condition has been corrected.
(1) Verify that all electrical accessories are off. CAUTION: Do not open any doors, or turn on any
Turn off all lamps, remove the ignition key, and close electrical accessories with the lowest milliampere
all doors. If the vehicle is equipped with an illumi- scale selected, or the multi-meter may be damaged.
nated entry system or an electronically tuned radio, (6) Observe the multi-meter reading. The low-am-
allow the electronic timer function of these systems perage IOD should not exceed twenty-five milliam-
to automatically shut off (time out). This may take peres (0.025 ampere). If the draw exceeds twenty-five
up to three minutes. milliamperes, isolate each circuit using the fuse and
(2) Determine that the under-hood lamp is operat- circuit breaker remove-and-replace process. The
ing properly, then disconnect the lamp wire harness multi-meter reading will drop to within the accept-
connector or remove the lamp bulb. able limit when the source of the excessive draw is
(3) Disconnect the battery negative cable. disconnected. Repair this circuit as required; whether
(4) Set an electronic digital multi-meter to its a wiring short, incorrect switch adjustment, or a
highest amperage scale. Connect the multi-meter component failure is at fault.
between the disconnected battery negative cable
clamp and the battery negative terminal post. Make
sure that the doors remain closed so that the illumi-
SERVICE PROCEDURES
nated entry system is not activated. The multi-meter
amperage reading may remain high for up to three BATTERY CHARGING
minutes, or may not give any reading at all while set A battery is fully-charged when:
in the highest amperage scale, depending upon the • All cells are gassing freely during battery charg-
electrical equipment on the vehicle. The multi-meter ing.
leads must be securely clamped to the battery nega- • A green color is visible in the sight glass of the
tive cable clamp and the battery negative terminal built-in test indicator.
post. If continuity between the battery negative ter- • Three hydrometer tests, taken at one-hour inter-
minal post and the negative cable clamp is lost dur- vals, indicate no increase in the temperature-cor-
ing any part of the IOD test, the electronic timer rected specific gravity.
function will be activated and all of the tests will • Open-circuit voltage is 12.4 volts or above.
have to be repeated.
WARNING:
(5) After about three minutes, the high-amperage
IOD reading on the multi-meter should become very
low or nonexistent, depending upon the electrical
equipment on the vehicle. If the amperage reading
remains high, remove and replace each fuse or circuit
breaker in the Power Distribution Center (PDC) and
then in the fuseblock module (refer to Power Distri-
bution Center and Fuse Block in the Component
Index of Group 8W - Wiring Diagrams for fuse and
circuit breaker identification) one at a time until the
amperage reading becomes very low, or nonexistent.
MAY RESULT.
This will isolate each circuit and identify the source
of the high-amperage IOD. If the amperage reading
remains high after removing and replacing each fuse
and circuit breaker, disconnect the wire harness from
the generator. If the amperage reading now becomes
very low or nonexistent, refer to Charging System
in the Diagnosis and Testing section of Group 8C -
Charging System to diagnose the condition. After the
high-amperage IOD has been corrected, switch the
multi-meter to progressively lower amperage scales
and, if necessary, repeat the fuse and circuit breaker
remove-and-replace process to identify and correct all
sources of excessive IOD. It is now safe to select the
8A - 14 BATTERY TJ
CAUTION:
• Always disconnect and isolate the battery neg-
ative cable before charging a battery. Do not exceed
sixteen volts while charging a battery. Damage to
the vehicle electrical system components may
result.
• Battery electrolyte will bubble inside the bat-
tery case during normal battery charging. Electro-
lyte boiling or being discharged from the battery
vents indicates a battery overcharging condition.
Immediately reduce the charging rate or turn off the
charger to evaluate the battery condition. Damage
to the battery may result from overcharging.
• The battery should not be hot to the touch. If
the battery feels hot to the touch, turn off the
charger and let the battery cool before continuing Fig. 14 Voltmeter Accurate to 1/10 Volt Connected -
the charging operation. Damage to the battery may Typical
result. (2) Disconnect and isolate the battery negative
cable. Connect the battery charger leads. Some bat-
Some battery chargers are equipped with polarity- tery chargers are equipped with polarity-sensing cir-
sensing circuitry. This circuitry protects the charger cuitry. This circuitry protects the charger and/or the
and/or the battery from being damaged if they are battery from being damaged if they are improperly
improperly connected. If the battery state-of-charge connected. If the battery state-of-charge is too low for
is too low for the polarity-sensing circuitry to detect, the polarity-sensing circuitry to detect, the charger
the charger will not operate. This makes it appear will not operate. This makes it appear that the bat-
that the battery will not accept charging current. See tery will not accept charging current. See the instruc-
the instructions provided by the manufacturer of the tions provided by the manufacturer of the battery
battery charger for details on how to bypass the charger for details on how to bypass the polarity-
polarity-sensing circuitry. sensing circuitry.
After the battery has been charged to 12.4 volts or (3) Battery chargers vary in the amount of voltage
greater, perform a load test to determine the battery and current they provide. The amount of time
cranking capacity. Refer to Load Test in the Diagno- required for a battery to accept measurable charger
sis and Testing section of this group for the proce- current at various voltages is shown in the Charge
dures. If the battery will endure a load test, return Rate chart. If the charge current is still not measur-
the battery to use. If the battery will not endure a able at the end of the charging time, the battery is
load test, it is faulty and must be replaced. faulty and must be replaced. If the charge current is
Clean and inspect the battery hold downs, tray, measurable during the charging time, the battery
terminals, posts, and top before completing service. may be good and the charging should be completed in
Refer to Battery in the Removal and Installation the normal manner.
section of this group for the proper cleaning and
inspection procedures. Charge Rate
Voltage Hours
CHARGING A COMPLETELY DISCHARGED
16.0 volts maximum up to 4 hours
BATTERY
The following procedure should be used to recharge 14.0 to 15.9 volts up to 8 hours
a completely discharged battery. Unless this proce- 13.9 volts or less up to 16 hours
dure is properly followed, a good battery may be
needlessly replaced.
(1) Measure the voltage at the battery posts with a CHARGING TIME REQUIRED
voltmeter, accurate to 1/10 (0.10) volt (Fig. 14). If the The time required to charge a battery will vary,
reading is below ten volts, the charge current will be depending upon the following factors:
low. It could take some time before the battery • Battery Capacity - A completely discharged
accepts a current greater than a few milliamperes. heavy-duty battery requires twice the charging time
Such low current may not be detectable on the of a small capacity battery.
ammeters built into many battery chargers. • Temperature - A longer time will be needed to
charge a battery at -18° C (0° F) than at 27° C (80°
F). When a fast charger is connected to a cold bat-
TJ BATTERY 8A - 15
tery, the current accepted by the battery will be very
low at first. As the battery warms, it will accept a
higher charging current rate (amperage).
• Charger Capacity - A battery charger that
supplies only five amperes will require a longer
charging time. A battery charger that supplies
twenty amperes or more will require a shorter charg-
ing time.
• State-Of-Charge - A completely discharged
battery requires more charging time than a partially
discharged battery. Electrolyte is nearly pure water
in a completely discharged battery. At first, the
charging current (amperage) will be low. As the bat- Fig. 15 Remove Battery Cable Terminal Clamp -
tery charges, the specific gravity of the electrolyte Typical
will gradually rise. cleaning solution (Fig. 16). Replace any battery cable
that has damaged or deformed terminal clamps.
WARNING: NEVER EXCEED TWENTY AMPERES
WHEN CHARGING A COLD (-1° C or 30° F) BAT-
TERY. THE BATTERY MAY ARC INTERNALLY AND
EXPLODE. PERSONAL INJURY AND/OR VEHICLE
DAMAGE MAY RESULT.
Battery Charging Timetable

Charging 5 10 20
Amperage Amperes Amperes Amperes
Open
Circuit Hours Charging at 21° C (70° F)
Voltage
12.25 to 6 hours 3 hours 1.5 hours
12.49
12.24
11.99
*Below 18 hours 9 hours 4.5 hours
10.00
*Refer to Charging A Completely Discharged Battery
Fig. 16 Clean Battery Cable Terminal Clamp -
Typical
WARNING: WEAR A SUITABLE PAIR OF RUBBER
BATTERY GLOVES (NOT THE HOUSEHOLD TYPE) WHEN
REMOVING A BATTERY BY HAND. SAFETY
REMOVAL GLASSES SHOULD ALSO BE WORN. IF THE BAT-
TERY IS CRACKED OR LEAKING, THE ELECTRO-
(1) Turn the ignition switch to the Off position. Be
LYTE CAN BURN THE SKIN AND EYES.
certain that all electrical accessories are turned off.
(2) Loosen the battery cable terminal clamps and (4) Remove the battery hold downs and remove the
disconnect both battery cables, negative cable first. If battery from the battery tray (Fig. 17).
necessary, use a puller to remove the terminal (5) Inspect the battery tray and hold downs for
clamps from the battery posts (Fig. 15). corrosion or damage. Remove any corrosion using a
(3) Inspect the battery cable terminal clamps for wire brush and a sodium bicarbonate (baking soda)
corrosion and damage. Remove any corrosion using a and warm water cleaning solution. Paint any exposed
wire brush or a post and terminal cleaning tool, and bare metal and replace any damaged parts.
a sodium bicarbonate (baking soda) and warm water (6) Slide the thermoguard off of the battery case.
Inspect the battery case for cracks or other damage
8A - 16 BATTERY TJ
Built-In Test Indicator in the Diagnosis and Test-
ing section of this group for more information. Also
refer to Battery Charging in the Service Procedures
section of this group for more information.
(9) If the battery is to be reinstalled, clean the out-
side of the battery case and the top cover with a
sodium bicarbonate (baking soda) and warm water
cleaning solution to remove any acid film (Fig. 19).
Rinse the battery with clean water. Ensure that the
cleaning solution does not enter the battery cells
through the vent holes. If the battery is being
replaced, refer to Battery Ratings and Classifica-
tions in the Specifications section of this group. Con-
firm that the replacement battery is the correct size
and has the correct ratings for the vehicle.
Fig. 17 Battery Hold Downs

that could result in electrolyte leaks. Also, check the
battery terminal posts for looseness. Batteries with
damaged cases or loose posts must be replaced.
(7) Check the electrolyte level in the battery. Use a
putty knife or another suitable wide flat-bladed tool
to pry the cell caps off (Fig. 18). Do not use a screw-
driver. Add distilled water to each cell until the liq-
uid reaches the bottom of the vent well. DO NOT
OVERFILL.
Fig. 19 Clean Battery - Typical

(10) Clean any corrosion from the battery terminal
posts with a wire brush or a post and terminal
cleaner, and a sodium bicarbonate (baking soda) and
warm water cleaning solution (Fig. 20).
INSTALLATION
(1) Reinstall the battery thermoguard by sliding it
over the battery case.
(2) Position the battery in the tray. Ensure that
the positive and negative terminal posts are correctly
positioned. The cable terminal clamps must reach the
correct battery terminal post without stretching the
cables (Fig. 21).
Fig. 18 Removing Cell Caps - Typical (3) Loosely install the battery hold down hard-
(8) Inspect the battery built-in test indicator sight ware. Ensure that the battery base is correctly posi-
glass for an indication of the battery condition. If the tioned in the tray, then tighten the hold downs to 4
battery is discharged, charge as required. Refer to N·m (35 in. lbs.).
TJ BATTERY 8A - 17
CAUTION: Be certain that the battery cables are
connected to the correct battery terminals. Reverse
polarity may damage electrical components.
(4) Connect and tighten the battery positive cable

terminal clamp. Then connect and tighten the bat-
tery negative cable terminal clamp. Tighten both bat-
tery cable terminal clamp bolts to 6.2 N·m (55 in.
lbs.).
(5) Apply a thin coating of petroleum jelly or chas-
sis grease to the exposed surfaces of the battery cable
terminal clamps and battery terminal posts.
Fig. 20 Clean Battery Terminal Post - Typical
Fig. 21 Battery Cables

8A - 18 BATTERY TJ
SPECIFICATIONS
BATTERY
Battery Classifications and Ratings

BCI Group Size Cold Cranking Reserve Load Test
Part Number Ampere-Hours
Classification Amperage Capacity Amperage
56027960 34 500 110 Minutes 60 250
56041003 34 600 120 Minutes 66 300

1999 Jeep TJ Wrangler Service Manual - 08. Electrical Systems

Uploaded by

Copyright:

Available Formats

1999 Jeep TJ Wrangler Service Manual - 08. Electrical Systems

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1999 Jeep TJ Wrangler Service Manual - 08. Electrical Systems

Uploaded by

Copyright:

Available Formats

TJ STARTING SYSTEMS 8B - 1

DESCRIPTION AND OPERATION STARTER RELAY . . . . . . . . . . . . . . . . . . . . . . . . 9

Starting System Diagnosis

WARNING: ON VEHICLES EQUIPPED WITH AIR- COLD CRANKING TEST

NOTE: A cold engine will increase the starter cur-

FEED CIRCUIT TEST

Fig. 6 Test Starter Ground - Typical

Fig. 4 Test Battery Positive Cable Resistance - CONTROL CIRCUIT TESTING

Fig. 7 Starter Motor Noise Diagnosis

NOTE: The shim thickness is 0.381 mm (0.015 in.).

CAUTION: The 2.5L engine uses a permanent mag-

Fig. 9 Continuity Test Between Solenoid Terminal

Fig. 14 Starter Wire Harness Remove/Install - 4.0L

Fig. 15 Power Distribution Center

Starter Motor and Solenoid

DESCRIPTION AND OPERATION ON-BOARD DIAGNOSTIC TEST FOR

WARNING: DISCONNECT NEGATIVE CABLE FROM REMOVAL

Fig. 2 Generator Remove/Install

Fig. 4 Battery Temperature Sensor Remove/Install

DESCRIPTION AND OPERATION SPARK PLUG CONDITIONS . . . . . . . . . . . . . . . . 8

DESCRIPTION AND OPERATION

POWERTRAIN CONTROL MODULE

SPARK PLUG CABLES

CRANKSHAFT POSITION SENSOR

Fig. 5 Crankshaft Position Sensor—Manual

IGNITION SWITCH AND KEY LOCK CYLINDER

Fig. 9 Ignition Coil—2.5L Engine

IGNITION COIL TEST

IGNITION COIL RESISTANCE

PRIMARY RESISTANCE SECONDARY RESISTANCE

Fig. 13 Rotor Inspection—Typical

OIL OR ASH ENCRUSTED

Fig. 17 Electrode Gap Bridging

Fig. 16 Oil or Ash Encrusted

Fig. 20 Preignition Damage

Fig. 19 Chipped Electrode Insulator

Fig. 22 Cable Removal

PLUG GAP ADJUSTMENT REMOVAL

Fig. 24 Ignition Coil—2.5L Engine

Fig. 26 Crankshaft Position Sensor—4.0L 6-Cyl.

Fig. 25 Ignition Coil—4.0L Engine

CRANKSHAFT POSITION SENSOR

CAMSHAFT POSITION SENSOR

Fig. 31 Distributor—2.5L Or 4.0L Engines—Typical

Fig. 34 Slot At 11 O’clock Position—4.0L Engine

Fig. 36 Distributor Pre-position—All Engines

Fig. 35 Pin Alignment Holes

IGNITION SWITCH AND KEY CYLINDER

KEY CYLINDER REMOVAL

Fig. 38 Distributor Engaged Position—4.0L

CAUTION: If the distributor cap is incorrectly posi-

(16) Install distributor cap. Tighten distributor cap

IGNITION SWITCH REMOVAL

Fig. 43 Ignition Switch Removal/Installation

KEY CYLINDER INSTALLATION

SHIFTER/IGNITION INTERLOCK ENGINE FIRING ORDER—2.5L 4-CYLINDER

SPARK PLUGS SPARK PLUG CABLE RESISTANCE

ENGINE PLUG TYPE ELECTRODE GAP MINIMUM MAXIMUM

IGNITION COIL RESISTANCE