Scribd
Upload
105 views6 pages

EF03085-HC-SR04 Ultrasonic Module User Guide

The document provides instructions for using an HC-SR04 ultrasonic module to measure distances. It describes the ultrasonic measurement principle of transmitting ultrasonic pulses and measuring the reflection time. It then gives an overview of the HC-SR04 module features and specifications, and provides examples of connecting the module to an Arduino UNO board and using its ultrasonic library functions to obtain distance measurements.

Uploaded by

Sreejith Skr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
105 views6 pages

EF03085-HC-SR04 Ultrasonic Module User Guide

The document provides instructions for using an HC-SR04 ultrasonic module to measure distances. It describes the ultrasonic measurement principle of transmitting ultrasonic pulses and measuring the reflection time. It then gives an overview of the HC-SR04 module features and specifications, and provides examples of connecting the module to an Arduino UNO board and using its ultrasonic library functions to obtain distance measurements.

Uploaded by

Sreejith Skr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

HC-SR04 User Guide

Part 1 Ultrasonic Introduction

1. 1 Ultrasonic Definition

The human ear can hear sound frequency around 20HZ ~ 20KHZ, and
ultrasonic is the sound wave beyond the human ability of 20KHZ .

1.2 Ultrasonic distance measurement principle


Ultrasonic transmitter emitted an ultrasonic wave in one direction, and started
timing when it launched. Ultrasonic spread in the air, and would return
immediately when it encountered obstacles on the way. At last, the ultrasonic
receiver would stop timing when it received the reflected wave. As Ultrasonic
spread velocity is 340m / s in the air, based on the timer record t, we can
calculate the distance (s) between the obstacle and transmitter, namely: s =
340t / 2, which is so- called time difference distance measurement principle
The principle of ultrasonic distance measurement used the already-known air
spreading velocity, measuring the time from launch to reflection when it
encountered obstacle, and then calculate the distance between the transmitter
and the obstacle according to the time and the velocity. Thus, the principle of
ultrasonic distance measurement is the same with radar.
Distance Measurement formula is expressed as: L = C X T
In the formula, L is the measured distance, and C is the ultrasonic spreading
velocity in air, also, T represents time (T is half the time value from transmitting
to receiving ).
1

1.3 Ultrasonic Application


Ultrasonic Application Technology is the thing which developed in recent
decades. With the ultrasonic advance, and the electronic technology
development, especially as high-power semiconductor device technology
matures, the application of ultrasonic has become increasingly widespread:
Ultrasonic measurement of distance, depth and thickness;
Ultrasonic testing;
Ultrasound imaging;
Ultrasonic machining, such as polishing, drilling;
Ultrasonic cleaning;
Ultrasonic welding;

n
Part 2 HC-SR04 Ultrasonic Module Introductio
Introduction
2.1 Product Features
Stable performance
Accurate distance measurement
High-density
Small blind
Application Areas:
Robotics barrier
Object distance measurement
Level detection
Public security
Parking detection

2.2 Product Image

Module pin definitions


2.3
2.3
Types
HC-SR04

Pin Symbol
VCC
Trig
Echo
GND

Pin Function Description


5V power supply
Trigger pin
Receive pin
Power ground

Electrical parameters
2.4
2.4
Electrical Parameters
Operating Voltage
Operating Current
Operating Frequency
Farthest Range
Nearest Range
Measuring Angle
Input Trigger Signal
Output Echo Signal
Dimensions

HC-SR04 Ultrasonic Module


DC-5V
15mA
40KHZ
4m
2cm
15 Degree
10us TTL pulse
Output TTL level signal, proportional
with range
45*20*15mm

2.5 Module operating Principle


Set low the Trig and Echo port when the module initializes , firstly, transmit
at least 10us high level pulse to the Trig pin (module automatically sends eight
40K square wave), and then wait to capture the rising edge output by echo port,
at the same time, open the timer to start timing. Next, once again capture the
falling edge output by echo port, at the same time, read the time of the counter,
which is the ultrasonic running time in the air. According to the formular: test
distance = (high level time * ultrasonic spreading

velocity in air) / 2, you can

calculate the distance to the obstacle.

Part3 Use Freaduino UNO to test HC-SR04


3.1 Freaduino uno and HC-SR04 Connection

Connection DescriptionD2<------>Trig
D3<------>Echo (The users
can define the connection pin by themselves)
Note You need to set the Freaduino UNO switch in 5V Side when use
together with HC-SR04 Module.
4

3.2 HCSR04 library function description


Long timing()
Function name: timing
Parameters: None
Return Value: the time of ultrasonic from the transmitter to the receiver
float CalcDistance(long microsec,int metric)
Function nameCalcDistance
microsec: the time of ultrasonic from the transmitter to the receiver
metric: Set the unit of the return value ( the value of 1 for cm, and the value
of 0 for in )
Return Value: the measured distance

3.3 Add the HC-SR04 Library


Step1:Download the Demo Code of HCSR04 Ultrasonic from address
http://www.elecfreaks.com/store/download/product/Sensor/HC-SR04/HCSR04Ultrasonic_demo.zip

and

then unpack it to get the file of HCSR04 Ultrasonic.


Step2: Add the file of HCSR04 Ultrasonic in the file of Arduino-1.0.X / libraries.
Step3:If you can see the Example of HCSR04 Ultrasonic in Arduino IDE, the
adding of HC-SR04 library has been successful.

3.4 Test the Module with the Examples of Library File


1. Open Arduino IDE 1.0.X, and choose the corresponding board and
serial port.
2. Click file/ examples/ HCSR04Ultrasonic until the code pop up.
3. Compiling sketch until Done uploading appears, which represents the
uploading has been successful.
4. Open serial monitor and set the corresponding BaudRate.
5. If you see similar information in serial monitor as below, you succeeded.

Chart 3HC-SR04 testing results

You might also like