Scribd
Upload
155 views1 page

CSP SMC 40774 Data Sheet 2012 PDF

This document provides data on the properties and applications of Sheet Molding Compound 40774(Gray/Black). Key properties include a specific gravity of 1.84-1.96, 27.5% fiberglass content, heat distortion temperature over 450°F, Barcol hardness of 50, and flexural strength of 26,000 PSI. Typical applications for this material include automotive and truck parts that require high strength and dimensional stability.

Uploaded by

Marioni Antonio Herrera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
155 views1 page

CSP SMC 40774 Data Sheet 2012 PDF

This document provides data on the properties and applications of Sheet Molding Compound 40774(Gray/Black). Key properties include a specific gravity of 1.84-1.96, 27.5% fiberglass content, heat distortion temperature over 450°F, Barcol hardness of 50, and flexural strength of 26,000 PSI. Typical applications for this material include automotive and truck parts that require high strength and dimensional stability.

Uploaded by

Marioni Antonio Herrera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

SHEET MOLDING COMPOUND DATA SHEET

40774(Gray/Black)
Sheet Molding Compound
ASTM Test
Method

Typical Molded
Property

Metric
Equivalent

Specific Gravity
Fiberglass Content
Heat Distortion Temp.
Barcol Hardness
Impact Strength (Izod/Notched)
Flexural Strength, PSI
Tensile Strength, PSI
Mold Shrinkage (Cold Piece
from Cold Mold, In./In.)
Coefficient of Expansion

D-792-98
D-648-98
D-2583-95
D-256-97
D-790-98
D-638-98

1.84-1.96
27.5%
>450F
50
15ftlb/in
26,000
10,000

1.84-1.96
27.5%
>235C
50
75 KJ/m2
180 MPa
69 MPa

D-696-98

.0000
7.6 x 10-6 (in/in/F)

Flexural Modulus (PSI x 106),

D-790-98

1.5

.0000
13.7 x 10-6
(cm/cm/C)
10 GPa

Property

Poissons Ratio

0.26

0.26

TYPICAL APPLICATIONS:
Parts requiring high strength and good dimensional stability. Typical applications: parts for
automotives,trucks,agriculture tractors,swimming pools, antenna dishes etc.

Rev: January,2012

Data presented herein is based upon tests performed in our labs on properly molded flat sheets tested according to standard procedures where referenced and what we believe to be appropriate methods where no standard
method exists. Since the values found in parts made from this material depend upon many factors beyond our control, such as molding conditions and procedures, part and mold design, operator skill and specific test
procedures employed, we do not guarantee that the specified results will be obtained on any specific part and urge prospective users to make their decisions based upon the performance of actual parts molded under
production conditions. NO WARRANTY OR MERCHANTABILITY OR FITNESS FOR PURPOSE IS GIVEN. Our liability and purchasers remedy for any fault in the product, whether the result of negligence or
otherwise, is limited to a refund of the cost of the material. This printed copy of this document is only for reference purposes and it is the responsibility of the user to verify the accuracy of this document against the
master list.

Continental Structural Plastics 755 W. Big Beaver Road, Suite 700 Troy, Michigan 48084

You might also like