Scribd Logo
Upload

Welcome to Scribd!

  • 906 views

    Calculation Sheet: Anchor Bolt Design Combined Tension and Shear Code Abbreviation

    Uploaded by

    NoppolNorasri
    This document provides design calculations for anchor bolts used to connect an oil sand drum to a concrete foundation. It includes anchor bolt data such as the factored tension and shear loads, concrete strength, bolt material properties, bolt dimensions, and embedment depth. Design codes and references used include ACI 318-08 and PIP STE05121. Calculations are provided to check bolt spacing, edge distances, and embedment depth against code requirements.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Calculation Sheet: Anchor Bolt Design Combined Tension and Shear Code Abbreviation

    Uploaded by

    NoppolNorasri
    906 views1 page
    This document provides design calculations for anchor bolts used to connect an oil sand drum to a concrete foundation. It includes anchor bolt data such as the factored tension and shear loads, concrete strength, bolt material properties, bolt dimensions, and embedment depth. Design codes and references used include ACI 318-08 and PIP STE05121. Calculations are provided to check bolt spacing, edge distances, and embedment depth against code requirements.

    Original Description:

    Anchor Bolt ACI 318-08_cal

    Original Title

    Anchor Bolt ACI 318-08_cal

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides design calculations for anchor bolts used to connect an oil sand drum to a concrete foundation. It includes anchor bolt data such as the factored tension and shear loads, concrete strength, bolt material properties, bolt dimensions, and embedment depth. Design codes and references used include ACI 318-08 and PIP STE05121. Calculations are provided to check bolt spacing, edge distances, and embedment depth against code requirements.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    906 views1 page

    Calculation Sheet: Anchor Bolt Design Combined Tension and Shear Code Abbreviation

    Uploaded by

    NoppolNorasri
    This document provides design calculations for anchor bolts used to connect an oil sand drum to a concrete foundation. It includes anchor bolt data such as the factored tension and shear loads, concrete strength, bolt material properties, bolt dimensions, and embedment depth. Design codes and references used include ACI 318-08 and PIP STE05121. Calculations are provided to check bolt spacing, edge distances, and embedment depth against code requirements.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 1

    Place Logo Here

    Project : Alberta
    OilSand
    NG SURGE
    DRUM

    Eng : D Wu P Eng.

    Job No : 1234567

    Chk : D Wu P Eng.

    Doc No : 1234567

    Calculation Sheet

    Date : 8/5/2014

    Subject : Headed Anchor Bolt Design ACI 318-08

    Rev : 1
    1 of 9

    ANCHOR BOLT DESIGN

    Combined Tension and Shear

    Anchor bolt design based on

    Code Abbreviation

    ACI 318-08 Building Code Requirements for Structural Concrete and Commentary Appendix D

    ACI 318-08

    PIP STE05121 Anchor Bolt Design Guide-2006

    PIP STE05121

    set Nu = 0 if it's compression

    Anchor Bolt Data


    Factored tension for design

    Nu = 11.35

    [kips]

    Factored shear

    Vu = 11.35

    [kips]

    Factored shear for design

    Vu = 11.35

    [kips]

    Concrete strength

    f'c = 4.0

    [ksi]

    [kN]

    = 50.5

    [kN]

    Vu = 0 if shear key is provided


    = 27.6

    [MPa]

    = 862

    [MPa]

    A193 Grade B7

    Anchor bolt material


    Anchor tensile strength

    Code Reference
    = 50.5

    futa = 125

    [ksi]

    Anchor is ductile steel element


    Anchor bolt diameter

    da =

    Bolt sleeve diameter

    ds = 2.0

    [in]

    Bolt sleeve height

    hs = 7.0

    [in]

    Anchor bolt embedment depth

    hef = 15.0

    [in]

    9.0

    OK

    Concrete thickness

    ha = 18.0

    [in]

    18.0

    OK

    Bolt edge distance c1

    c1 = 5.0

    [in]

    4.5

    OK

    Bolt edge distance c2

    c2 = 5.0

    [in]

    4.5

    OK

    Bolt edge distance c3

    c3 = 5.0

    [in]

    4.5

    OK

    Bolt edge distance c4

    c4 = 5.0

    [in]

    4.5

    [in]

    0.75

    ACI 318-08
    D.1

    = 19.1

    [mm]

    PIP STE05121
    Page A -1 Table 1

    min required
    Page A -1 Table 1

    Page A -1 Table 1

    OK

    ACI 318-08

    ci > 1.5hef for at least two edges to avoid reducing of hef when Nu > 0

    No

    D.5.2.3

    Adjusted hef for design

    hef = 15.00

    [in]

    9.0

    OK

    D.5.2.3

    Outermost bolt line spacing s1

    s1 = 54.0

    [in]

    3.0

    OK

    PIP STE05121

    Outermost bolt line spacing s2

    s2 = 54.0

    [in]

    3.0

    OK

    Page A -1 Table 1

    Required No. of Bolts

    = 2 / side (min)

    You might also like