Scribd Logo
Upload

Welcome to Scribd!

  • 67 views

    How To Make A Tatting Shuttle: Fruitloopjanney

    Uploaded by

    Luis Alfonso Zárate Chafla
    This document provides instructions for making a tatting shuttle in 3 steps: 1. Design and cut out the shuttle shape from 3mm plywood using a hand saw. Drill holes and slots for the cotton. 2. Sand the entire shuttle smooth using coarse then fine sandpaper. 3. Apply two coats of varnish, sanding between coats, to protect and further smooth the surface. Hang to dry.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    How To Make A Tatting Shuttle: Fruitloopjanney

    Uploaded by

    Luis Alfonso Zárate Chafla
    67 views1 page
    This document provides instructions for making a tatting shuttle in 3 steps: 1. Design and cut out the shuttle shape from 3mm plywood using a hand saw. Drill holes and slots for the cotton. 2. Sand the entire shuttle smooth using coarse then fine sandpaper. 3. Apply two coats of varnish, sanding between coats, to protect and further smooth the surface. Hang to dry.

    Original Description:

    Como construir una lanzadera

    Original Title

    Lanza Dera

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for making a tatting shuttle in 3 steps: 1. Design and cut out the shuttle shape from 3mm plywood using a hand saw. Drill holes and slots for the cotton. 2. Sand the entire shuttle smooth using coarse then fine sandpaper. 3. Apply two coats of varnish, sanding between coats, to protect and further smooth the surface. Hang to dry.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    67 views1 page

    How To Make A Tatting Shuttle: Fruitloopjanney

    Uploaded by

    Luis Alfonso Zárate Chafla
    This document provides instructions for making a tatting shuttle in 3 steps: 1. Design and cut out the shuttle shape from 3mm plywood using a hand saw. Drill holes and slots for the cotton. 2. Sand the entire shuttle smooth using coarse then fine sandpaper. 3. Apply two coats of varnish, sanding between coats, to protect and further smooth the surface. Hang to dry.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    How to make a tatting shuttle | fruitloopjanney

    1 de 2

    https://fruitloopjanney.wordpress.com/2011/02/01/how-to-make-a-tatting...

    fruitloopjanney

    How to make a tatting shuttle


    Posted on February 1, 2011

    This one is made from Plywood, about 3mm thick. I am not uploading a template, as I hope to sell these, but you
    can make your own shape. I have made mine around 65mm (2 and a half inches) long.
    1. Materials I used were: 3mm plywood. electric drill sand paper, both
    heavy and light hand saw varnish
    2 Design your shape and trace onto
    plywood. Placement of holes and
    slots can also be made at this time.
    3. Cut out shape with hand saw.
    4. Drill pilot holes with a smaller
    drill first.
    5. With a larger drill, drill a hole
    half way through the shuttle. Then
    turn it over and complete the hole.
    This stops it splitting the wood.
    6. This could have been done at the
    same time as I cut out the shape,
    but I cut the slots at this stage.
    Then I sanded the whole thing with
    a rough grit sandpaper, and then
    with fine sandpaper.
    7. To get it really smooth so their are no rough edges to snag the cotton
    onto, I varnish it twice, sanding it with fine sandpaper inbetween each
    coat. Hang it by a wire to dry. Water based varnish dries quite quickly too.

    18/08/2015 12:47

    You might also like