Scribd
Upload
62 views

GSM Arduino

This code is used to send sensor data from an Arduino to a web server. It initializes the Ethernet and DHT11 temperature sensor. It takes an average temperature reading over a set delay period. It then connects to a pushingbox API server and sends an HTTP GET request containing the device ID and average temperature in the URL parameters. It prints responses and disconnects before repeating in a loop. The relevant parts like MAC address, IP, device ID, and API URL need to be configured for the specific setup.

Uploaded by

Alex Lopes
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
62 views

GSM Arduino

This code is used to send sensor data from an Arduino to a web server. It initializes the Ethernet and DHT11 temperature sensor. It takes an average temperature reading over a set delay period. It then connects to a pushingbox API server and sends an HTTP GET request containing the device ID and average temperature in the URL parameters. It prints responses and disconnects before repeating in a loop. The relevant parts like MAC address, IP, device ID, and API URL need to be configured for the specific setup.

Uploaded by

Alex Lopes
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

#include <SoftwareSerial.

h>
SoftwareSerial gprsSerial(7, 8);
void setup()
{
gprsSerial.begin(19200);
Serial.begin(19200);
Serial.println("Config SIM900...");
delay(2000);
Serial.println("Done!...");
gprsSerial.flush();
Serial.flush();
// attach or detach from GPRS service
gprsSerial.println("AT+CGATT?");
delay(100);
toSerial();
// bearer settings
gprsSerial.println("AT+SAPBR=3,1,\"CONTYPE\",\"GPRS\"");
delay(2000);
toSerial();
// bearer settings
gprsSerial.println("AT+SAPBR=3,1,\"APN\",\"epc.tmobile.com\"");
delay(2000);
toSerial();
// bearer settings
gprsSerial.println("AT+SAPBR=1,1");
delay(2000);
toSerial();
}
void loop()
{
// initialize http service
gprsSerial.println("AT+HTTPINIT");
delay(2000);
toSerial();
// set http param value
gprsSerial.println("AT+HTTPPARA=\"URL\",\"http://YOUR.DOMAIN.COM/rest/receiveS
ensorData?sensorval1=blah&sensorval2=blah\"");
delay(2000);
toSerial();
// set http action type 0 = GET, 1 = POST, 2 = HEAD
gprsSerial.println("AT+HTTPACTION=0");
delay(6000);
toSerial();
// read server response
gprsSerial.println("AT+HTTPREAD");
delay(1000);
toSerial();

gprsSerial.println("");
gprsSerial.println("AT+HTTPTERM");
toSerial();
delay(300);
gprsSerial.println("");
delay(10000);
}
void toSerial()
{
while(gprsSerial.available()!=0)
{
Serial.write(gprsSerial.read());
}
}

Just change "epc.tmobile.com" to the apn for your carrier and


"YOUR.DOMAIN.COM" to your server info and change the "sensorval1=blah" to
your variable and sensor data.
Let me know if you get this working or not. I can help you figure it out it's not too
hard.
Good Luck.

https://spreadsheets.google.com/formResponse?formkey=YOUR FORM KEY &ifq&


YOUR ENTRY =THE VALUE TO STORE &submit=Submit
https://spreadsheets.google.com/formResponse?
formkey=dDBMdUx3TmQ5Y2xvX2Z0V183UVp2U0E6MQ
&ifq&entry.0.single=Boris&entry.2.single=Landoni&submit=Submit

#include <SPI.h>
#include <Ethernet.h>
#include <EthernetUdp.h>
#include <SPI.h>
#include <dht11.h>

#undef int
#undef abs
#undef double
#undef float
#undef round
dht11 DHT11;
#define DHT11PIN 3

///////////////////////////////
///

EDIT THIS STUFF

//

///////////////////////////////

byte mac[] = {0xAA, 0xBB, 0xCC, 0xDD, 0xEE, 0xFF }; //Replace with your
Ethernet shield MAC
byte ip[] = {123,456,7,890};

// Your Arduino device IP address

char devid = v42FE15BC09B20df // THIS IS THE DEVICE ID FROM


PUSHINGBOX

int del=300; // Amount of seconds delay between posting to google docs.

///////////////////////////////

//

DONE EDITING

//

///////////////////////////////

char postmsg[100];
int k=0;
int temp_av = 0;
char server[] = "api.pushingbox.com";
EthernetClient client;

void setup()
{
Serial.begin(9600);
Ethernet.begin(mac, ip);
delay(1000);
Serial.println("connecting...");
}

void loop(){

// average temp reading for 'del' time.........................................

for(int j=0; j<del;j++)


{
// Read local temp........................................
int chk = DHT11.read(DHT11PIN);
int temp = Fahrenheit(DHT11.temperature);
temp_av=temp_av+temp;
delay(1000);
}

int avtemp=temp_av/(del);
temp_av=0;

// Post to Google Form.............................................


if (client.connect(server, 80))
{
k=0;
Serial.println("connected");
sprintf(postmsg,"GET /pushingbox?devid=%c&status=%d
HTTP/1.1",devid,avtemp); // NOTE** In this line of code you can see where
the temperature value is inserted into the wed address. It follows 'status='
Change that value to whatever you want to post.
client.println(postmsg);
client.println("Host: api.pushingbox.com");
client.println("Connection: close");
client.println();

Serial.println(postmsg);

Serial.println("Host: api.pushingbox.com");
Serial.println("Connection: close");
Serial.println();

delay(1000);
client.stop();
}
delay(1000);

if (!client.connected())
{
Serial.println();
Serial.println("disconnecting.");
client.stop();
k==1;
return;
}

double Fahrenheit(double celsius) // Function to convert to Fahrenheit


{
return 1.8 * celsius + 32;
}

You might also like