Scribd
Upload
114 views

Crack Excel

The document summarizes the design parameters for checking crack width in a concrete beam section. It provides the section dimensions, reinforcement details, material properties, and calculated values like neutral axis depth and crack width. The crack width is calculated at a check point between bars based on the shortest distance from the point to the bar, the average steel strain at that point, and the neutral axis depth determined from the section geometry and reinforcement. The calculated crack width is 0.09396266 mm, less than the specified limit.

Uploaded by

Md Mohsin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
114 views

Crack Excel

The document summarizes the design parameters for checking crack width in a concrete beam section. It provides the section dimensions, reinforcement details, material properties, and calculated values like neutral axis depth and crack width. The crack width is calculated at a check point between bars based on the shortest distance from the point to the bar, the average steel strain at that point, and the neutral axis depth determined from the section geometry and reinforcement. The calculated crack width is 0.09396266 mm, less than the specified limit.

Uploaded by

Md Mohsin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Crack Width Check

Design Parameter:
1 Depth of Section
2 Width of section
3 Minimum Clear Cover
4 Dia. Of main tensional bar (db)
5 No.of bar
6 Spacing of bar
7 Grade of concrete
8 Grade of reinforcement
9 Modulus of elasticity of steel
10 Depth of crack check level
11 Design Moment
12 Dia. Of Top compression bar (db),
13 Spacing of top reinforcement
14 No.of Bar

h
b
Cmin
n
s
M
Fe
Es
a
M
S
n

1200 mm
1000 mm
50 mm
32 mm
10
100 mm
25
500
210000 n/mm2
1200 mm
1068.963 Kn-m
25 mm
100 mm
10

The Crack width of the section is checked at point A, at soffit of beam between the mid point o

The design crack width (Wcr) t a selected levl, A on the surface of the section with Max Momen

Where
Acr
m
x

Shortest distance from the selected level on the surfa


Average strain of steel at the selected level
Depth of neutral axis

Calculation of Acr

sqrt of [(100/2)^2 +66^2]-32/2


66.80
mm

Calculation of Neutral Axis depth :Effective depth , d = (h - dc)


=
Modulur ratio, m = 280/(3 x cb)

(1200-66)
1134 mm
[As per IS;-456]

Ast=2/(4@) *
no. of. bars
Asc=2/(4@) *
no. of. bars

11 [cbc = 8.5 MPa for M25 Grade of Conc.]

8042.24 mm2
[Effective cover at top dct= Cmin + db/2
4908.59 mm2

Moment about N-A,


(b x X) x X/2 + (m-1) x Asc x (X-dct) = mAst x (d-X)
#VALUE!
X^2 +275.08X -206719.42 = 0
500 (x*x)
226481387375.312
338.6039670304
Therefore,X = 337 mm
J
M
T
FS

1021.13201
1068.963
1046.84114

130.167856
0.00061985

E1

0.00067128

Em

0.00048716

Wcr

0.09396266

137296.6

Wcr

eam between the mid point of consecutive two main longitudinal bar.

the section with Max Moment is,

he selected level on the surface to a longitudinal bar


the selected level

Effective cover dc= Cmin + db/2 =

66

0.09396

Grade of Conc.]

ct= Cmin + db/2

62.5

-103815510

w
l
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190

1.5 m
3.75
7.5
11.25
15
18.75
22.5
26.25
30
33.75
37.5
41.25
45
48.75
52.5
56.25
60
63.75
67.5
71.25

You might also like