Mil Coating

LOCKHEED MARTIN REPORT NUMBER: 16PR070S
Aeronautics Company Date: 21 May 2003

FSCM 81755 Superseding: 16PR070R
FINISH CODES FOR

F-16 AIR COMBAT FIGHTER
(Supplement to FPS-3001)
Contract Number F33657-88C-0037
Releasability of this material under the Freedom of

Information Act is subject to the restrictions on release in
DoD Regulation 5400.7-R and DoD Directive 5230.25.
FINISH CODES
FOR
F-16 AIR COMBAT FIGHTER
(Supplement to FPS-3001)
Prepared By: Approved By:
J. P. Reynolds R. V. Wolff
Materials & Processes Integ. Analysis Materials & Processes Integ. Analysis
CHANGE INDEX
The following changes have been made to 16PR070 since the last revision.
Element/Code Reason for Change

Added new finish codes A822, To provide new finish codes needed for various F-16 programs.
A823, A969-A975, S665-S668,
T412
Re-added finish code T401 Inadvertently dropped from a prior revision.
Added new basic elements To support new finish code creation
408, 409, 553, 554, and 555
Corrected finish code A813 Code was worded so that primer was not required in white painted
areas
Updated finish code A801 Prior wording did not allow use of MIL-C-85285 urethane coating
Updated finish codes A476 and To provide finish requirements for fitting types not previously used in
A478, and basic element 203 production
Updated basic elements To include FMS-1058-1 as an authorized touchup primer.
involving touchup of primer
i
TABLE OF CONTENTS
Para Page
1 SCOPE 1
1.1 PURPOSE 1
2 USE OF FINISH CODES 1
2.2 FINISH CODES 1
2.3 BASIC ELEMENTS 1
2.4 SELECTION OF FINISH CODE 2
2.5 EXTERIOR SURFACES OF THE AIRPLANE 4
2.6 SPECIAL CODES 7
2.7 ADDITIONAL CODES 7
2.7.1 Supplementary Materials 7
2.7.2 Overspray 7
2.7.3 ADDITION OF PRIMER AND PAINT TO STANDARD PARTS DURING FINISHING OF
ASSEMBLIES 7
2.7.4 TOUCHUP 7
2.7.5 COLOR NUMBER SUBSTITUTIONS 7
3 REVISIONS AND CONTRACTUALITY 7
APPENDIX A: FINISH CODE STEPS A-1

Section A (Aluminum Alloy Finish Codes) A-1
Section D (Non-CRES Alloy Finish Codes) A-124
Section E (Plastic and Reinforced Plastic Finish Codes) A-136
Section F (FSX/F-2 Finish Codes) A-141
Section N (Copper and Nickel Finish Codes) A-142
Section R (Special Finish Codes) A-144
Section S (CRES Alloy Finish Codes) A-150
Section T (Titanium Alloy Finish Codes) A-174
Section W (Restricted Finish Codes) A-177
APPENDIX B: BASIC ELEMENTS B-1
LIST OF TABLES
Table Page
A CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES 9
D CROSS REFERENCE GUIDE TO NON-CRES ALLOY STEEL
FINISH CODES 20
S CROSS REFERENCE GUIDE TO CRES ALLOY FINISH CODES 22
ii
FINISH CODES FOR F-16 AIR COMBAT FIGHTER
1 SCOPE
1.1 PURPOSE - This report contains the finishing codes and related finishing combinations for use on
F-16 aircraft in accordance with the requirements of FPS-3001. FPS-3001 is the basis for selection of
codes that will be specified on engineering drawings. The drawings will reference FPS-3001 as the
applicable document without reference to the revision letter. Reference herein to FPS-3001 shall be
understood to refer to the current revision of FPS-3001 and Specification Change Notices (SCN's)
attached thereto.
2 USE OF FINISH CODES

2.1 Codes within this document have been established for incorporation in the "FINISH" column of the
Parts List (PL). Between formal revisions, changes and additions will be made by internal memo and will
take effect once the memo is released by Materials and Processes Engineering. Finish codes shall be
retained in this document for effectivity reasons even if the finish combination has become obsolete.
2.2 FINISH CODES - Finish codes are listed in Appendix A of this document. Appendix A is divided
into sections, with each section listing the finish codes pertaining to a different class of substrate material.
The sections are as follows:
Section A - Aluminum Alloys
Section D - Non-Corrosion Resistant Steel Alloys
Section E - Plastic, Glass Reinforced Plastic, and Graphite Composite
Section F – FSX/F-2 Special Use Codes
Section N - Copper and Nickel Alloys
Section R - Special Finishes
Section S - Corrosion Resistant Alloys
Section T - Titanium Alloys
Section W - Restricted Finishes
Each finish code consists of a letter prefix, designating basic substrate type, and a sequential three digit
number, designating the individual finish sequence. In no instance shall the letter prefix of numbers be
used separately in the Parts List. The finish for bonded assemblies containing multiple materials will be
covered under codes in Section R. The finish codes translate the cleaning and finishing requirements of
FPS-3001 for Engineering drawings and planning.
2.3 BASIC ELEMENTS - Each finish code consists of basic elements listed in steps that define the
cleaning and surface treatment, and the paint coating requirements. The basic elements are listed in
Appendix B. Finish codes for several alloys also provide basic elements for restoration of finish that was
removed by planning required action only, after the part had been finished. Where Engineering assembly
or installation drawings call for removing finish (e.g., for spotface), the drawing must specify in a note to
restore finish by the restoration basic element. The designer should use the rationale given in Para. 2.4
for selecting the proper finish code for the part.
Selected surface treatment basic elements as shown in the finish codes which are peculiar to individual
metals have been specified with a letter prefix when subsequent paint coatings are not applied, e.g.,
S146. This requires that the CRES part be passivated per FPS-3007, metal removal not permitted.
These are shown in the applicable code sections.
1
2.4 SELECTION OF FINISH CODE - Selection of the proper finish code is directly related to the
designer's knowledge of finish requirements as specified in the preceding section of this specification.
The designer must be familiar with these contractual requirements and be governed by them rather than
by a personal preference of finishes.
The following procedure and examples will be of benefit to the designer as a guide for selecting the
proper finish for a design:
Step 1. Determine the physical location with respect to the aircraft of the part or component in question.
FPS-3001 covers these areas in the following paragraphs as noted therein:
3.2 Basic Exterior Finish
3.3 Special Exterior Finish
3.4 Basic Interior Finish
3.5 Special Interior Finish
3.6 Special Finishes
Step 2. Determine the material of construction of the part or component. Subparagraphs of the above
primary paragraphs specify requirements for aluminum, titanium, corrosion resistant alloys, plated parts,
glass reinforced plastics, and graphite composites. Notice that the first requirement given refers to 3.1 of
FPS-3001 for cleaning and surface treatment requirements. Cleaning options are incorporated in the
finish codes and will not require a specific call-out on the Engineering Drawing.
Step 3. Determine the applicable surface treatment requirement as specified in 3.1 of FPS-3001.
Subparagraphs of 3.1 specify requirements for aluminum, titanium, corrosion resistant steel, non-
corrosion resistant steel, copper, nickel, magnesium alloys, glass reinforced plastics, and graphite
composites.
Step 4. Determine the complete finishing requirements for the part or component by combining the
above requirements and comparing these with Basic Element descriptions in front of the Finish Codes.
Step 5. Determine the proper code for the complete finishing requirement from the applicable section of
this document and enter in the FINISH column of the PL.
NOTE: Due to the large number of "A", "D" and "S" finish codes, a cross-reference guide has been
provided at the end of this section for quick access to applicable codes. It is emphasized that the guide is
not a substitute for thorough examination of finish requirements, and the individual finish codes should
always be consulted. The on-line Finish Code Data Base will have Code Selector Screens that will aid
Engineers in obtaining finish codes.
RATIONALE AND EXAMPLES OF FINISH CODE SELECTION
EXAMPLE NO. 1 - Finish code for bare 2024-T851 fuselage longeron in non-fuel area.
Step 1 - Fuselage longeron should be Basic Interior finish, Para. 3.4 of FPS-3001.
Step 2 - Material of construction is bare 2024-T851 aluminum alloy. Para. 3.4.2 specifies
finish for aluminum alloy. Para. 3.4.2(b) specifies finish for 2024 aluminum as
follows:
(1) Clean and surface treat per 3.1.1(a).
2
(2) FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer (2 coats).

Step 3 - Surface treatment requirement for aluminum is specified in 3.1.1, with noted
exceptions in 3.1.1.1 through 3.1.1.5. None of the exceptions apply to this part.
Surface treatment requirements are as follows:
(1) Clean with mild abrasives, solvents, vapor or solution degreasing, inhibited alkaline
cleaners, or approved acid cleaners.
(2) Anodize per MIL-A-8625 Type I, or FPS-3090.
(The basic element for these is 111, which covers both cleaning and anodize.)
Step 4 - Complete finish requirements are:
(1) Clean per para. 3.1.1(a) and anodize per MIL-A-8625 Type I, or FPS-3090 (Basic
element 111).
(2) FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 primer (2 coats) (Basic element
204).
Step 5 - Proper code for the complete finishing requirements, specified in A-Aluminum Alloys,
is as follows:
A403 - PRIMER, BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS
A) ANODIZE ALL SURFACES PER 111.
A) PRIME ALL SURFACES TWO COATS PER 204 (OR 245).
A) TOUCH UP AS REQUIRED PER 236.
EXAMPLE NO. 2 - Finish Code for D6ac support bracket heat treated to 220-240 ksi Ftu and located
interior in a non-fuel area with thermal environment less than 450°F with primer to be omitted
in close tolerance holes.
Step 1 - Support bracket should be Basic Interior Finish, Para. 3.4 of FPS-3001.
Step 2 - Material of construction is D6ac steel, 220-240 ksi strength range. D6ac is a non-
corrosion resistant steel alloy requiring plating (FPS-3001 Para. 3.1.4). Para. 3.4.5
specifies finish for plated alloys as follows:
(1) Clean and surface treat per 3.1 in accordance with alloy.
(2) FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer (1 coat).
Step 3 - Surface treatment requirement for non-corrosion resistant steel alloys is specified in
3.1.4, with noted exceptions in 3.1.4.4 through 3.1.4.10. None of the exceptions
apply to this part. Surface treatment requirements of 3.1.4.3 are as follows:
Clean per FPS-3001, Para. 3.1.4 and cadmium plate per the following specifications:
(1) FPS-1007, Grade B, Type II, Class 2 or
(1) MIL-C-8837, Type II, Class 2 as an alternate if vendor is not qualified for plating FPS-
1007, Grade B.
(Both cleaning and cadmium plating are covered in basic elements 122 and 123.)
Step 4 - Complete finishing requirements are:
3
(1) Clean per FPS-3001, para. 3.1.4, and cadmium plate in accordance with FPS-1007,
Grade B, Type II, Class 2 or vacuum cadmium plate per MIL-C-8837, Type II, Class
2, or coat per MIL-C-83488, Class 3, Type II, Aluminum Ion Vapor Deposition,
followed by FPS-3083 glass bead peening. (Basic element 122 or 123.)
(2) FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 primer (1 coat) (Basic element 202).
Step 5 - Proper code for the complete finishing requirement, specified in D-Non-Corrosion
Resistant Steel alloy is as follows:
D413 - ALLOY STEEL - (CADMIUM PLATE) PRIMER, HEAT TREAT RANGE 220-240 KSI
A) CADMIUM PLATE ALL SURFACES PER 122 OR 123.
A) PRIME ONE COAT ON AREAS SPECIFIED ON DRAWING PER 202.
A) TOUCH UP AS REQUIRED PER 307.
The area of primer omission is specified on the drawing or in a general note.
2.5 EXTERIOR SURFACES OF THE AIRPLANE - FPS-3001 contains the specification requirements
for the finishing of the exterior surfaces of the airplane. Where practical, the exterior skins and areas
defined as exterior surfaces of the airplane shall be finished after assembly of the aircraft. It is usually
necessary to finish reverse surfaces of the exterior skins that form the interior surfaces of the airplane at
the detail level.
Drawing 16N0001, Finishing of F-16 Airplanes is the top assembly drawing of all the F-16 type-version
painting drawings (also referred to as 16NXXXX). Each of the type-version painting drawings designates
the specific finish to be applied to the exterior surfaces of the airplane in accordance with the specification
requirements of FPS-3001. A special series of codes has been provided for the designer to enter on the
PL for the purpose of finishing exterior skins whose reverse surface forms the interior surface of the
airplane as given in the following examples:
EXAMPLE NO. 3 - Finish Code for bare 7475-T7351 fuel boundary with exposure of one surface to
fuel and the other surface having a mixture of exterior exposed surface, finished after
assembly, plus an area which is covered that requires interior prime only.
Step 1 - The requirements should be Basic Exterior Finish, Para. 3.2, for the exterior surface;
Special Interior Finish, Para. 3.5.2, for the fuel surface; and portions of exterior
surfaces are interior non-fuel area, Para. 3.4.2(b).
Step 2 - Material of construction is bare 7475-T7351 aluminum. Para. 3.2.2 specifies that the
exterior finish for aluminum alloys is as follows:
(1) Clean and surface treat per 3.1.1.
(3) MIL-C-83286 or MIL-C-85285 Urethane Coating (2 coats) with color per 3.3.3.
Para. 3.4.2(b) specifies that the interior finish for non-clad 7000-series aluminum is
as follows:
(2) FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer (2 coats).
Para. 3.5.2 specifies finish for fuel tank interior as follows:
4
The inside surface of fuel tank area shall be finished with MIL-C-27725 coating and
sealed to prevent corrosion and leakage of fuel per FPS-1004.
Step 3 - Surface treatment for aluminum is specified in Para 3.1.1, with noted exceptions in
3.1.1.1 through 3.1.1.5. None of the exceptions apply to this part. Surface treatment
requirement is as follows:
(2) Anodize per MIL-A-8625, Type I or FPS-3090.
(Both cleaning and anodizing are covered in basic element 111.)
Interior Surface - Fuel Tank
(1) Clean per FPS-3001, para. 3.1.1(a) and anodize per MIL-A-8625, Type I or FPS-
3090 (Basic element 111).
(2) Apply fuel tank corrosion protective coating per FPS-1004, (Basic element 221).
Exterior Exposed Surface
(1) Clean per FPS-3001, para. 3.1.1(a) and anodize per MIL-A-8625 Type I or FPS-
3090, per para. 3.1.1(b)(1) (Basic element 111).
(2) FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer (1 coat) on areas
specified (Basic element 202).
(3) MIL-C-83286 or MIL-C-85285 Urethane Coating (2 coats) in areas specified.
(FSD only - Exterior exposed surfaces will be anodized in detail, then recleaned after
assembly per paragraph 3.7.19, primed and painted per drawing 16N0001
requirements. Production F-16A #7 and on, F-16B #3 and on, with earlier effectivity
permitted, will have the exterior surfaces primed in detail and then painted per
drawing 16N0001 requirements).
Interior Surface - Non-Fuel Area
(1) Clean per FPS-3001, para. 3.1.1(a) and anodize per MIL-A-8625 Type I or FPS-3090
per para. 3.1.1(b)(1), (Basic element 111).
(2) FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer (2 coats), (Basic
element 205).
Step 5 - Proper code for the complete finishing requirement, specified in Section A -
Aluminum Alloys is as follows:
A703 - PRIMER, AMS-C-27725 FUEL TANK COATING, AND 16NXXXX FINISH, BARE
2000 AND 7000 SERIES ALUMINUM ALLOYS WITH PART OF EXTERIOR
SURFACE COVERED
A) ANODIZE ALL SURFACES PER 111.
A) APPLY AMS-C-27725 COATING TO INTERIOR FAYING SURFACES AND
SURFACES EXPOSED TO FUEL PER 221.
A) PRIME TWO COATS ON EXTERIOR COVERED SURFACE AS NOTED ON
DRAWING PER 205 (OR 245).
A) PRIME REMAINING EXTERIOR EXPOSED SURFACE ONE COAT PER 202.
5
A) FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING

16N0001.
A) TOUCH UP AS REQUIRED PER 235, 236, 240, AND 242.
EXAMPLE NO. 4 - Clad 2024-T81 Exterior Skin - Non-fuel area

Step 1 - The requirements should be Basic Exterior Finish, Para. 3.2, for the exterior surface;
and Basic Interior Finish, Para. 3.4, for the interior surface.
Step 2 - Material of construction is clad 2024-T81 aluminum alloy. Para. 3.2.2 specifies that
the exterior finish for aluminum alloys is as follows:
(3) MIL-C-83286 or MIL-C-85285 Urethane Coating (2 coats) with color per 3.3.3.
Para. 3.4.2(a) specifies that the interior finish for clad aluminum alloys is as follows:
Step 3 - Surface treatment for aluminum is specified in Para 3.1.1, with noted exceptions in
3.1.1.1 through 3.1.1.5. None of the exceptions apply to this part. Surface treatment
requirement is as follows:
(2) Chemical film treat per MIL-C-5541.
(Both cleaning and chem film are covered in basic element 105.)
Interior Surface
(1) Clean per para. 3.1.1(a) and chemical film treat per MIL-C-5541 per para. 3.1.1(b)(3)
(Basic element 105).
(2) Apply 1 coat FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer (Basic
element 201).
Exterior Surface
(1) Clean per para. 3.1.1(a) and chemical film treat per MIL-C-5541 per para. 3.1.1(b)(3)
(Basic element 105).
(2) Apply 1 coat FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer (Basic
element 201).
(1) MIL-C-83286 or MIL-C-85285 Urethane Coating (2 coats).
(FSD only - Exterior exposed surfaces will be anodized in detail, then recleaned after
assembly, per paragraph 3.7.19, primed and painted per drawing 16N0001
requirements. Production F-16A #7 and on, F-16B #3 and on, with earlier effectivity
6
permitted, will have the exterior surfaces primed in detail and then painted per
drawing 16N0001 requirements.)
Step 5 - Proper code for the complete finishing requirement, specified in Section A -
Aluminum Alloys is as follows:
A441- PRIMER AND 16NXXXX FINISH, CLAD OR 1000, 3000, 5000 OR 6000 SERIES
ALUMINUM ALLOYS
A) CHEM FILM ALL SURFACES PER 105.
A) PRIME ONE COAT ALL SURFACES PER 201.
A) FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING
16N0001.
A) TOUCH UP AS REQUIRED PER 235 AND 242.
2.6 SPECIAL CODES - Due to the complex nature of finishing required by certain parts, special codes
have been provided. These codes will enable the designer to specify on the drawing the final finish of the
part or component at the detail level.
2.6.1 There will be instances when the general nature of the part or component will require multiple
colors or types of finishes. Under such circumstances each section of the coded document contains
codes to be entered on the PL of the drawing that will combine individual finish codes.
2.7 ADDITIONAL CODES - In the event a special type of finish is required for which no code has
been provided, the following procedure should be followed:
(1) Designers at LM Aero shall contact Materials and Processes Engineering for the
establishment of new codes.
(2) Designers at all other facilities shall contact their Materials Engineering or Materials and
Processes Engineering personnel for the establishment of new codes. Materials Engineering
or Materials and Processes Engineering personnel shall contact the LM Aero Materials and
Processes Engineering for new codes. In all instances, the new codes for materials and
processes shall be consistent with the requirements of this specification.
2.7.1 SUPPLEMENTARY MATERIALS - Materials such as thread, electrical wire, fabrics, adhesives,
etc., which do not require finishing and/or for which there are no codes assigned within this specification,
shall be given a code of 0000 on the Parts List (PL) and other related documents.
2.7.2 OVERSPRAY - It is permissible for overspray of a colored topcoat or fuel tank coating onto
adjacent primed surfaces which do not require a colored topcoat or fuel tank coating.
2.7.3 ADDITION OF PRIMER AND PAINT TO STANDARD PARTS DURING FINISHING OF
ASSEMBLIES - In order to prevent excessive masking, it is permissible to prime and paint MS 21266
standard parts when they are riveted or bonded to an assembly, unless otherwise specified on the
drawing. The standard parts must be primed and painted to match the assembly to which they are
attached.
2.7.4 TOUCHUP - Areas of parts which are touched-up after installation will differ slightly in texture
and color from original paint and/or prime finish. This difference is permissible.
2.7.5 COLOR NUMBER SUBSTITUTIONS - Due to changes made to FED-STD-595, the following
color numbers may be substituted as follows.
(a) Color No. 17925 (white) may be substituted for Color No. 17875 (white).
3 REVISIONS AND CONTRACTUALITY
7
3.1 Formal revisions of Report 16PR070 will be in accordance with MIL-STD-480.
8
CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES

SECTION A
FINISH 2000 & 7000 7000 SERIES & 2219 1000,3000,5000,6000 CASTINGS
SERIES SERIES & CLAD
No Top No Finish 100 100
Finish
Anodize 111, 113H, 115H, 163B 111, 113H, 115H, 163B 111, 113H, 115H, 163B, 113H, 115H, 163B
474H, 480
Chemical Film 134R, 797 134R, 797 134R, 176, 797, 875 134R, 797, 875
Anodize and 854, 889H
Chemical Film
Single Primer 403, 405, 491, 520R, 404, 406, 492, 520R, 401, 402, 455, 471, 478, 407, 408, 483
Finish 664, 666, 884R, 823P 562, 884R 520R,527B, 869, 884R 520R, 656, 884R
AMS-C-27725 Fuel 240R, 427, 542, 564, 240R, 428, 429, 495 240R,426, 477, 482, 240R, 426, 477
Tank Coating 629, 931 541
FMS-3014 Form 2 800, 818H, 820, 870H 870H 805, 817, 819H, 821, 805, 817, 819H,
Adhesive Primer 870H 821, 870H
FMS-3011 Form II 686, 687
Adhesive Primer
FMS-3018 Form II 300 300 300 300
Adhesive Primer
White Urethane 466, 468, 519R, 634H 467, 469, 519R, 536H, 460, 473, 476, 485, 503, 460, 503, 506H,
873, 970R 970R 519R, 678H, 874, 923, 519R, 874, 959P,
959P, 970R 970R
White Acrylic 616, 617, 619R 619R 614, 618, 619R, 620, 633 614, 615, 618,
Lacquer/White 619R
Urethane
White Teflon- 792 792
Urethane
Orange-Yellow 533H 533H 533H 533H
Epoxy Enamel/
Orange-Yellow
Urethane
Lusterless Red 641
Lacquer
Light Gray 681, 683, 851H 680, 682 680, 682
Urethane
Lusterless Gray 591, 601H, 602, 643R, 589H, 601H, 643R 590, 601H, 603, 643R, 590, 601H, 643R,
Urethane 589R 589H, 881 589H, 881
Gray Urethane 609, 610 861, 871 861, 871
Dark Gray 565, 721 522, 523 578, 605, 723, 793 578, 605, 723, 793
Urethane
Medium Gray 642 642
Teflon-Urethane
Gray Epoxy 457, 458, 531H, 572, 531H, 579R, 607R, 456, 459, 470, 475, 502, 459, 502, 531H,
Enamel/Gray 579R, 607R, 645H 645H 531H, 572, 579R, 607R, 572, 579R, 607R,
Urethane 645H, 781 645H, 781
Lusterless Black 580, 584, 638, 644H, 581, 582, 640, 587H 581, 582, 587H
Urethane 587H
P6096-2 Flat Black 535, 559, 597, 789, 560H, 570, 571, 604, 915 560H, 570, 571,
Urethane 915 915
Black Epoxy 440, 509H, 529, 599, 509H, 530, 532, 599, 509H, 554, 599, 878, 509H, 526, 540,
Enamel/Black 882R 882R 879, 882R 554, 599, 879,
Urethane 882R
16NXXXX Finish 511, 514, 528R, 538R, 512, 515, 528R, 538R 513, 516, 517, 524, 513, 516, 517,
539, 567, 574 528R, 538R, 543, 746, 524, 528R, 538R,
887 545, 887
Light Semi-gloss 954 973
Gray Urethane
9
CROSS REFERENCED GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

SECTION A
FINISH 2000 & 7000 SERIES 7000 SERIES & 2219 1000,3000,5000,6000 CASTINGS
SERIES & CLAD
Single Solid Film 508H, 544H, 557, 569, 508H, 544H, 646H 508H, 544H, 646H, 674, 508H, 544H,
Finish Lubricant 646H 799 646H, 674, 799
(Cont'd)
FMS-1058-1 868R, 876H, 890H, 924 868R 868R, 924 868R
Primer
Two AMS-C-27725 Fuel 432, 657, 862 433, 494 434, 479 507
Finishes Tank Coating
Primer
And...
FMS-3014 Form 2 816
Adhesive Primer
White Urethane 461, 566, 662, 673, 462, 510 465, 782, 972 537, 782
786,796
White Acrylic 626 615
Lacquer/White
Urethane
Orange-Yellow 422 421 420
Epoxy Enamel/
Orange-Yellow
Urethane
Light Gray 852, 948P 575 672 672
Urethane
Lusterless Gray 598
Urethane
Gray Urethane 613 895
Medium Gray 650
Urethane
Dark Gray 720, 726H, 773, 944 722
Urethane
Medium Gray 794 794
Teflon-Urethane
Gray Epoxy 409, 645H, 654, 946 410 645H 411, 645H
Enamel/Gray
Urethane
Lusterless Black 787 788, 888 788
Urethane
P6096-2 Flat Black 417 418 416, 891, 928R 419
Urethane
Blue Urethane 935, 936, 938 933, 934, 937
Black Urethane 504
Black Epoxy 413 414 412, 568 415
Enamel/Black
Urethane
16NXXXX Finish 442, 496, 499, 546,573, 443, 496, 744 441, 481, 496, 608, 679, 444, 496, 547,
576, 630, 655, 675, 677 745 660, 679, 705,
702, 731, 742, 777C, 745, 747
790H, 926, 951P, 966P
Solid Film 472, 859H 561
Lubricant
Nickel-Cadmium 855W
Plate
Dark Gray Teflon- 963
Urethane
Light Semi-gloss 955P, 975P 956P 956P
Gray Urethane
10
CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

SECTION A
White Urethane 430, 439, 658, 671, 431, 556 438, 484 438, 484
Two 710
Finishes, White Acrylic 625
AMS-C- Lacquer/White
27725 Urethane
Fuel Lusterless Gray 592, 659
Tank Urethane
Coating Gray Urethane 785
and... Gray Epoxy 550 552
Enamel/Gray
Urethane
Lusterless Black 583
Urethane
Black Epoxy 549
Enamel/Black
Urethane
16NXXX Finish 436, 577, 741 437 435 435
Solid Film Lubricant 562, 652
Two White Urethane 801, 810
Finishes, Gray Urethane 809
FMS- 16NXXXX Finish 803, 811, 812, 814
3014
Form 2
Adhesive
Primer
and ...
Two White Urethane and 621
Finishes White Acrylic
Misc. Lacquer/White
Urethane
White Urethane and 593 606 606
Lusterless Gray
Urethane
White Urethane and 490
Gray Epoxy Enamel
/Gray Urethane
White Urethane and 596 600 600
Lusterless Black
Urethane
Black Epoxy
Enamel/Black
Urethane
White Urethane and 464, 505R, 632R, 505R, 553, 632R, 676L, 463, 493, 505R, 632R, 463, 493, 505R,
16NXXXX Finish 712, 729H, 961R, 729H, 961R 676L, 729H, 925, 961R, 521, 632R, 676L,
965P 962P, 965P 729H, 961R, 962P
Solid Film Lubricant
White Acrylic 622
Lacquer/White
Urethane and
Lusterless Gray
Urethane
11

SECTION A
FINISH 2000 & 7000 7000 SERIES & 1000,3000,5000,6000 CASTINGS
SERIES 2219 SERIES & CLAD
Two White Acrylic Lacquer/White 624
Finishes Urethane and Lusterless
Misc. Black Urethane
(Cont'd)
White Acrylic 623, 628, 637, 648, 628 627, 628, 647 627, 628, 647
Lacquer/White Urethane 668, 964P
and 16NXXXX Finish
White Acrylic Lacquer/White 651 651
Urethane and P6194-1
Coating
White Teflon-Urethane and 850
16NXXXX Finish
White Epoxy Enamel/ White 649
Urethane and Black Epoxy
Enamel/ Black Urethane
Light Gray Urethane and 498, 947P 497, 949P 497, 949P
16NXXXX Finish
Lusterless Gray Urethane 594 595 595
and 16NXXXX Finish
Gray Urethane and 611R, 612, 684 611R 611R, 685, 688, 894 611R, 685, 894
16NXXXX Finish
Dark Gray Urethane and 635, 636R, 856, 893, 636R 500, 501, 636R 500, 636R
16NXXXX Finish 974P
Med. Gray Teflon- 791
Urethane &
16NXXXX Finish
Gray Epoxy Enamel/Gray 548 548
Urethane and P6096-2 Flat
Black Urethane
Gray Epoxy Enamel/Gray 447 448 446 446
Urethane and 16NXXXX
Finish
Urethane and P6194-1
Coating
Urethane and Solid Film
Lubricant
Black Epoxy Enamel/Black 877 877
Urethane and P6096-2 Flat
Black Urethane
Black Epoxy Enamel/Black 880 880
Urethane and Solid Film
Lubricant
Black Epoxy Enamel/Black 450 451 449 449, 715@
P6096-2 Flat Black 453 454 452 452
Lusterless Black and 585 586 586
16NXXXX
Red Urethane and Solid 872H 872H 872H 872H
Film Lubricant
Solid Film Lubricant and 866H
FMS-1058-1 Primer
FMS-3035 Flexible Primer 930 930 930 930
and White Urethane
12

SECTION A
Three AMS-C-27725 Fuel 661, 708
Finishes, Tank Coating, and
Primer White Urethane
and...
AMS-C-27725 Fuel 757
Tank Coating, and
White Acrylic
Lacquer/White
Urethane
Tank Coating, and
Black Epoxy Enamel/
Black Urethane
AMS-C-27725 Fuel 665, 701, 703, 734, 704 940
Tank Coating, and 863
16NXXXX Finish
AMS-C-27725 Fuel 864H, 865
Tank Coating and
FMS-3014 Form 2 815
Adhesive Primer, and
White Urethane
FMS-3014 Form 2 804
Adhesive Primer and
16NXXXX Finish
White Urethane and 667, 767
White Acrylic
Lacquer/White
Urethane
Lusterless Gray
Urethane
White Urethane and 717, 727, 764, 783, 885H 853, 885H 754, 763, 885H
16NXXXX Finish 798, 885H, 927,
971P
White Acrylic 761
Lacquer/White
Urethane and
Lusterless Gray
Urethane
White Acrylic 758 769
Lacquer/White
Urethane and
16NXXXX Finish
Light Gray Urethane 886
and 16NXXXX Finish
Light Gray Urethane 743
and Dark Gray
Teflon-Urethane
Lusterless Gray 776 753
Urethane and
16NXXXX Finish
Dark Gray Urethane, 669H, 774H, 795R, 795R 795R 771, 795R, 950P
and 16NXXXX Finish 952HP
Light Semi-gloss 958HP 957P
Gray Urethane and
16NXXXX Finish
13

SECTION A
FINISH 2000 & 7000 SERIES 7000 SERIES & 2219 1000,3000,5000,6000 CASTINGS
SERIES & CLAD
Three Dark Gray 780 730
Finishes, Urethane, and Solid
Primer Film Lubricant
and...
(Cont'd)
Dark Gray Teflon- 732
Urethane, and
16NXXXX Finish
Gray Urethane, and 929
16NXXXX Finish
Black and Orange- 425 424 423
Yellow Epoxy
Enamel or Urethane
Stripes
16NXXXX Finish, 740, 772H, 858H, 860 772H 772H 772H
and Solid Film
Lubricant
Three White Urethane and 770
Finishes, White Acrylic
AMS-C- Lacquer/White
27725 Urethane
Fuel Tank White Urethane and 749
Coating Lusterless Gray
and... Urethane
Black Epoxy
Enamel/Black
Urethane
16NXXXX Finish
White Acrylic 760
Lacquer/White
Urethane and
16NXXXX Finish
Light gray Urethane, 735
and 16NXXXX
Finish
Lusterless Gray 748
Urethane and
16NXXXX Finish
Lusterless Black 751
Urethane, and
16NXXXX Finish
Black Epoxy 725
Enamel/Black
Urethane and
16NXXXX Finish
Three White Urethane and 807
Finishes, 16NXXXX Finish
FMS-
3014
Form 2 White Acrylic 813
Adhesive Lacquer/White
Primer Urethane and
and... 16NXXXX Finish
14

SECTION A
FINISH 2000 & 7000 SERIES 7000 SERIES & 1000,3000,5000,6000 CASTINGS
2219 SERIES & CLAD
Three White Urethane, White 766
Finishes Acrylic Lacquer/White
Misc. Urethane, and
Lusterless Gray
Urethane
White Urethane, 755
Lusterless Gray
Urethane, and
Lusterless Black
Urethane
White Urethane, 750 752 752
Lusterless Gray
Urethane, and
16NXXXX Finish
White Urethane, Solid 713H, 857H 713H 713H 713H
Film Lubricant, and
16NXXXX Finish
White Acrylic 762
Lacquer/White
Urethane, Lusterless
Gray Urethane, and
Lusterless Black
Urethane
White Acrylic 759 756 756
Lacquer/White
Gray Urethane, and
16NXXXX Finish
White Acrylic 765
Lacquer/White
Black Urethane, and
16NXXXX Finish
Four Primer, AMS-C-27725 707, 716, 739 724, 738 932
Finishes Fuel Tank Coating,
Misc. White Urethane, and
16NXXXX Finish
Primer, FMS-3014 808
Form 2 Adhesive
Primer, White
Urethane, and
16NXXXX Finish
Primer, White 775
Urethane, White
Acrylic Lacquer/White
Urethane, and
16NXXXX Finish
Primer, AMS-C-27725 943
Fuel Tank Coating,
White Acrylic
Lacquer/White
Urethane, and
16NXXXX Finish
15

SECTION A
Four Primer, White 784 784
Finishes Acrylic
Misc. Lacquer/White
Urethane,
Lusterless Gray
Urethane, and
16NXXXX Finish
Tank Coating,
White Urethane,
White Acrylic
Lacquer/White
Urethane and
Lusterless Gray
Urethane
Five Primer, AMS-C- 706
Finishes 27725 Fuel Tank
Misc. Coating, White
Urethane, Gray
Teflon-Urethane,
and 16NXXXX
Finish
Primer, AMS-C- 867
27725 Fuel Tank
Coating, White
Urethane,
16NXXXX Finish,
and FMS-1058-1
Primer
MISCELLANEOUS
DESCRIPTION NO FINISH SPECIAL FINISHES
DETAIL OF BONDED ASSEMBLY 103
DETAIL OF WELDED ASSEMBLY 104
ADHESIVE BONDED ASSEMBLIES 486, 487, 488, 489, 639
AERODYNAMIC SEALS 712, 713H
HINGED ACCESS PANELS 630, 631, 632, 883
NAMEPLATE OVERCOAT, CLEAR 275
ACRYLIC LACQUER PER MIL-L-19537
WINGS SKINS 706, 707, 739, 867, 868
ALUMINUM TUBING ASSYS 470, 471, 473 - 482, 484, 485, 620, 652,
822, 853, 854, 889, 896, 923, 972
ADHESIVE BONDED ASSYS 486 – 489
PROTECTIVE SHIPPING PAPER 210
16
CROSS REFERENCE GUIDE TO NON-CRES ALLOY STEEL FINISH CODES

SECTION D
ALLOY TENSILE STRENGTH

FINISH <180 KSI 180 - 220 KSI 220 - 240 KSI > 240 KSI
No Top No Finish 100, 104 100, 104 100, 104 100, 104
Finish Cadmium Plate 120 121 401 123
Single Solid Film 453 459 459 454, 462
Finish Lubricant
Single Primer 402, 406, 475 407 413, 460C 419
Finish White Urethane 405 410, 461C, 476 416, 417 420
(with Dark Gray Urethane 431 428 412W, 428
Cadmium
Plate or Gray Epoxy Enamel 403 408 414
IVD /Gray Urethane
Alumi- Lusterless Black 429 430
num) Urethane
Black Epoxy 404 409 415
Enamel/ Black
Urethane
Tank Coating
Two Primer and Solid 450 451 451 452
Finishes Film Lubricant
White Urethane and 705, 707
Solid Film
Lubricant
Chrome Plate and 703C
Two Primer and 702
Finishes Lusterless Black
(with Urethane
Cadmium Primer and Black 701
Plate or Epoxy Enamel/
IVD Black Urethane
Aluminum Primer and 472 473
16NXXXX Finish
AMS-C-27725 Fuel 474 474
Tank Coating and
White Acrylic
Lacquer/White
Urethane
White Urethane and 471 423
Corrosion
Preventive
Compound
Black and Orange- 411
Yellow Epoxy
Enamel or Urethane
Stripes
16NXXXX Finish 456
and Solid Film
Lubricant
16NXXXX Finish 457 457
and Molybdenum
Wear Coating
17
CROSS REFERENCE GUIDE TO NON-CRES ALLOY STEEL FINISH CODES (Cont'd)

SECTION D
ALLOY TENSILE STRENGTH

FINISH <180 KSI 180 - 220 KSI 220 - 240 KSI > 240 KSI
Three Primer, Lusterless 458
Finishes Black Urethane,
and Solid Film
Lubricant
Primer, Black 455
Epoxy Enamel/
Black Urethane,
and Solid Film
Lubricant
Primer, White 704
Urethane, and
Solid Film
Lubricant
MISCELLANEOUS
DESCRIPTION SPECIAL FINISHES
Special ALLOY STEEL SPRINGS 425, 426, 427, 470
Finishes ALLOY STEEL TUBE 701, 702
ROUGH FORGINGS 210
REWORK 136R, 421R, 422R, 424R
18
CROSS REFERENCE GUIDE TO CRES ALLOY FINISH CODES

SECTION S
FINISH 300 SERIES OR HEAT TREATABLE AISI410 OR 17-4 CASTINGS
CRES
No Top No Finish 146, 147, 411, 627SW 100@, 146+, 147+, 627SW+
Finish
Cadmium Plate (or IVD Alum) 420W, 433W, 643W, 647W 420W+, 433W+
Chrome Plate 633W, 634W
Cadmium (or IVD alum) Plate and 644W
Chrome Plate
Single Primer 424, 428, 436 402, 456
Finish AMS-C-27725 Fuel Tank Coating 635 406
White Urethane 419, 423, 437, 645 405, 409
White Acrylic Lacquer/White Urethane 450, 451
Flat White Epoxy Enamel/Flat White 418, 422
Urethane
Orange-Yellow Epoxy Enamel/Orange- 432 454
Yellow Urethane
Lusterless Gray Urethane 445, 446
Dark Gray Urethane 449, 640, 641, 660, 668 434@, 631@
Medium Gray Teflon-Urethane 629
Gray Epoxy Enamel/Gray Urethane 412, 414, 430 403
Lusterless Black Urethane 443, 444, 455 442, 447
P6096-2 Flat Black Urethane 429 427
Black Epoxy Enamel/Black Urethane 413, 415, 439 404, 439+, 440
16NXXXX Finish 425
Solid Film Lubricant 601, 602, 603, 608D, 612, 615, 617, 632C, 601+, 602+, 603+, 610, 618, 625,
654 654+
Corrosion Preventive Compound 208, 210
FMS-3014 Form 2 Adhesive 646, 705
Single Solid Film Lubricant with Cadmium Plate 606W, 661W 606W+, 661W+
Finish or IVD Aluminum
(with Solid Film Lubricant with Chrome Plate 632W, 662W
Plate)
19
CROSS REFERENCE GUIDE TO CRES ALLOY FINISH CODES (Cont'd)

SECTION S
FINISH 300 SERIES OR HEAT TREATABLE AISI410 OR 17-4 CASTINGS
CRES
Two Primer and White Urethane 457, 462 408
Finishes Primer and Lusterless Gray Urethane 448
Primer and Dark Gray Urethane 441
Primer and Blue Urethane 460, 707, 459 458
Primer and 16NXXXX Finish 435, 658
Primer and Solid Film Lubricant 626 616@
Primer and Corrosion Preventive 703 421
Compound
AMS-C-27725 Fuel Tank Coating and 638
White Acrylic Lacquer/White Urethane
White Urethane and 16NXXXX Finish 623, 639, 704, 706 407
White Urethane and Solid Film Lubricant 604, 605 605+, 653
Orange-Yellow Epoxy Enamel/Orange- 624 611, 624+
Yellow Urethane and Solid Film
Lubricant
Light Gray urethane and 16NXXXX 438, 642
Finish
Light Semi-gloss Gray Urethane and 464P, 663P 664P
16NXXXX Finish
Dark Gray Urethane and 16NXXXX 452, 659, 665P, 667 453@, 666@P
Finish
Gray Epoxy Enamel/Gray Urethane and 609, 613, 614 609+, 622@
Gray Epoxy Enamel/Gray Urethane and 426
Corrosion Preventive Compound
Black and Orange-Yellow Epoxy 431 431
Enamel/Orange-Yellow Urethane
Lusterless Black Urethane and Solid 620 620+
Film Lubricant
P6096-2 Flat Black Urethane and Solid 619
Film Lubricant
Black Epoxy Enamel/Black Urethane 607, 655 607+, 657@
and Solid Film Lubricant
MIL-C-85054 Corrosion Preventive 649@
Compound and Solid Film Lubricant
Three Gray Urethane, 16NXXXX Finish, and 628
Finishes Solid Film Lubricant
16NXXXX Finish, Solid Film 621
Lubricant, and Corrosion Preventive
Compound
Red Epoxy Enamel/Red Urethane, 656
16NXXXX Finish, and Solid Film
Lubricant
Four Primer, AMS-C-27725 Fuel Tank 461, 463
Finishes Coating, White Urethane, and 16NXXXX
Finish
20
CROSS REFERENCE GUIDE TO CRES ALLOY FINISH CODES (Cont'd)

SECTION S
MISCELLANEOUS
DESCRIPTION SPECIAL FINISHES
Special DETAIL OF BONDED ASSEMBLY 103
Finishes DETAIL OF WELDED ASSEMBLY 104
CRES TUBING 410, 416, 417
AERODYNAMIC SEALS 636, 637
NOTES FOR ALUMINUM, NON-CRES, AND CRES ALLOY FINISH CODE CROSS REFERENCE TABLES:
1. This chart is to be used as a guide and is not a substitute for the actual finish codes. Individual finish codes
should always be consulted.
2. No duplications of finish codes have been made vertically. Horizontal duplication of a finish code has been
made only in instances when it is applicable to more than one category of alloy or tensile strength.
Suffix Notations for Aluminum, Non-CRES, and CRES Alloy Finish Codes
B - Black Dye Anodize
C - Chrome Plate
D - Nitrided Surfaces
H - Hard Anodize
L - Applied Over Solid Film Lubricant
P – Primers restricted for FMS-3049 compatibility
R - Rework
S - Silver Plate/Strike
W - Nickel Plate/Strike or Electroless Nickel
@ - Casting Only
+ - Castings Excluded
3. 16NXXXX FINISH is listed in the Cross-References as a possible finish. No differentiation is made regarding
interior or exterior surfaces.
4. "PRIMER" by itself refers to FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer.
21
LOCKHEED MARTIN Specification: 16PR070S
Aeronautics Company Dated: 21 May 2003
APPENDIX A. Finish Codes

SECTION A. ALUMINUM ALLOYS
CODE APPLICABLE FINISH
A100 NO FINISH REQUIRED
A NO FINISH REQUIRED
A103 DO NOT FINISH. DETAIL OF BONDED ASSEMBLY
A104 DO NOT FINISH. DETAIL OF WELDED ASSEMBLY.
A105 SMALL DETAILS OF PARTS IN ELECTRICALLY BONDED ASSY'S
CLAD AND 1000, 3000, 5000, AND 6000 SERIES ALUMINUM ALLOYS
A CHEM FILM ALL SURFACES PER 105.
B (INACTIVE FOR NEW DESIGN, SEE A176)
A111 ANODIZED PARTS REQUIRING NO OTHER FINISH SUCH AS THOSE OPERATING
IN OIL OR FUEL - ALL WROUGHT ALUMINUM ALLOYS
A ANODIZE ALL SURFACES PER 111.
A113 HARD ANODIZED FUNCTIONAL WEAR SURFACES
ALL ALUMINUM ALLOYS
A HARD ANODIZE ALL SURFACES PER 113.
A115 HARD ANODIZED FUNCTIONAL WEAR SURFACES
ALL ALUMINUM ALLOYS (FOR PRESS FIT APPLICATION ONLY)
A HARD ANODIZE SPECIFIED SURFACES PER 115.
A134 REWORK OF ANODIZED FITTINGS
ALL ALUMINUM ALLOYS AND ONLY FOR "AN" TYPE
ANODIZED FITTINGS
A BRUSH CHEM FILM SPECIFIED SURFACES PER 134.
A163 CONTROLLED ENVIROMENT, BLACK ANODIZE FOR THERMAL CONTROL
ALL ALUMINUM ALLOYS
A SULFURIC ACID ANODIZE AND DYE BLACK ALL SURFACES PER 163.
A176 CLAD AND 1000, 3000, 5000, AND 6000 SERIES
ALUMINUM AND ALUMINUM CASTINGS.
A210 CORROSION PREVENTIVE SHIPPING PAPER
ALL ALUMINUM ALLOYS (FOR F2 ONLY)
A PREPARE ALL SURFACES PER 526.
A240 REWORK OF AMS-C-27725 COATED ALUMINUM PARTS
ALL ALUMINUM ALLOYS
A TOUCH UP AREAS WITH FINISH REMOVED PER 240.
A401 PRIMER
B PRIME SPECIFIED SURFACES ONE COAT PER 202.
C TOUCH UP AS REQUIRED PER 242.
A-1

A402 PRIMER
B PRIME ALL SURFACES ONE COAT PER 201.
A403 PRIMER
BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS
B PRIME ALL SURFACES TWO COATS PER 204 (OR 245).
A404 PRIMER
A SULFURIC ACID ANODIZE ALL SURFACES PER 112.
D (SEE A403 FOR PREFERRED CODE).
NOTE: DO NOT USE WITHOUT MATERIALS & PROCESSES ENGINEERING
APPROVAL.
A405 PRIMER
BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS (CLOSE TOLERANCE FITS)
A ANODIZE SPECIFIED SURFACES PER 114.
B PRIME SPECIFIED SURFACES TWO COATS PER 205 (OR 245).
C BRUSH CHEM FILM UNANODIZED AREAS PER 134.
D TOUCH UP AS REQUIRED PER 236.
A406 PRIMER
BARE 7000 SERIES AND 2219 ALUMINUM ALLOYS (CLOSE TOLERANCE FITS)
A SULFURIC ACID ANODIZE SPECIFIED SURFACES PER 124.
C BRUSH CHEM FILM UNANODIZED AREAS PER 134.
E (SEE A405 FOR PREFERRED CODE).
APPROVAL.
A407 PRIMER
ALUMINUM ALLOY CASTINGS
A408 PRIMER
A-2

A409 PRIMER AND GRAY EPOXY ENAMEL/GRAY URETHANE
B PRIME ONE COAT ON EXPOSED SURFACE PER 202.
C PRIME TWO COATS ON REVERSE SURFACE PER 205 (OR 245).
D PAINT EXPOSED SURFACES WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
E TOUCH UP AS REQUIRED PER 236 AND 238.
BARE 7000 SERIES AND 2219 ALUMINUM ALLOYS
B PRIME ONE COAT ON EXPOSED SURFACE PER 202.
D PAINT EXPOSED SURFACE WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
F (SEE A409 FOR PREFERRED CODE).
APPROVAL.
B PRIME EXPOSED SURFACE ONE COAT PER 202.
C PRIME REVERSE SURFACE TWO COATS PER 205 (OR 245).
D PAINT EXPOSED SURFACE WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
A412 PRIMER AND BLACK EPOXY ENAMEL/BLACK URETHANE
C PAINT EXPOSED SURFACE WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
D TOUCH UP AS REQUIRED PER 242 AND 239.
PER 213.
D PRIME REVERSE SURFACE TWO COATS PER 205 (OR 245).
A-3

D PAINT EXPOSED SURFACE WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
F (SEE A413 PREFERRED CODE).
APPROVAL.
D PAINT EXPOSED SURFACE WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
A416 PRIMER AND P6096-2 FLAT BLACK URETHANE
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS
C PAINT EXPOSED SURFACE WITH P6096-2 FLAT BLACK URETHANE PER 217 (OR 286).
D PAINT EXPOSED SURFACE WITH P6096-2 FLAT BLACK URETHANE PER 217 (OR 286).
APPROVAL.
A-4

A420 PRIMER AND ORANGE-YELLOW EPOXY ENAMEL/ORANGE-YELLOW
URETHANE
ALUMINUM CASTINGS
C PRIME REVERSE SURFACE TWO COATS PER 205 (OR 245)
D PAINT EXPOSED SURFACE WITH ORANGE-YELLOW EPOXY ENAMEL OR
ORANGE-YELLOW URETHANE PER 216.
A421 PRIMER AND ORANGE-YELLOW EPOXY ENAMEL/ORANGE-YELLOW
URETHANE. CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS
B PRIME ALL SURFACES PER 201.
C PAINT EXPOSED SURFACE WITH ORANGE-YELLOW EPOXY ENAMEL OR
A422 PRIMER AND ORANGE-YELLOW EPOXY ENAMEL/
ORANGE-YELLOW URETHANE
D PAINT EXPOSED SURFACE WITH ORANGE-YELLOW EPOXY ENAMEL OR
A423 PRIMER AND ORANGE-YELLOW AND BLACK STRIPES
D PAINT EXPOSED SURFACE WITH ALTERNATELY STRIPED BLACK AND
ORANGE-YELLOW EPOXY ENAMEL PER 218.
A-5

CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS.
C PAINT EXPOSED SURFACE WITH ALTERNATELY STRIPED BLACK AND
ORANGE-YELLOW EPOXY ENAMEL OR URETHANE PER 218.
D PAINT EXPOSED SURFACE WITH ALTERNATELY STRIPED BLACK AND
E TOUCH AS REQUIRED PER 236 AND 244.
A426 AMS-C-27725 FUEL TANK COATING. CLAD OR 1000,
3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND
ALUMINUM CASTINGS, EXCEPT TUBING.
B APPLY AMS-C-27725 COATING ALL SURFACES PER 220.
A427 AMS-C-27725 FUEL TANK COATING
APPROVAL.
BARE 7000 SERIES AND 2219 ALUMINUM ALLOYS (PRESS FITS)
B APPLY AMS-C-27725 COATING TO SPECIFIED SURFACES PER 221.
APPROVAL.
A-6

A430 AMS-C-27725 FUEL TANK COATING AND WHITE URETHANE
B APPLY AMS-C-27725 COATING ON SPECIFIED FAYING SURFACES AND
C PRIME REMAINING SURFACES ONE COAT PER 202.
D PAINT PRIMED SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
C PAINT WITH WHITE URETHANE COATING EXPOSED SURFACE PER 222 (OR 274).
D APPLY AMS-C-27725 COATING ON FAYING SURFACES AND SURFACES EXPOSED TO
FUEL PER 221.
APPROVAL.
A432 PRIMER AND AMS-C-27725 FUEL TANK COATING
B PRIME INTERIOR NON-FUEL SURFACE TWO COATS PER 205 (OR 245).
C APPLY AMS-C-27725 COATING ON FAYING SURFACES AND SURFACES EXPOSED TO
FUEL PER 221.
B PRIME TWO COATS ON INTERIOR NON-FUEL SURFACE PER 205 (OR 245).
FUEL PER 221.
APPROVAL.
B PRIME ONE COAT ON INTERIOR NON-FUEL SURFACES PER 202.
FUEL PER 221.
A-7

A435 AMS-C-27725 FUEL TANK COATING AND 16NXXXX FINISH
CLAD OR 1000, 3000, 5000 OR 6000 SERIES ALUMINUM
ALLOYS AND ALUMINUM CASTINGS
B APPLY AMS-C-27725 COATING ON FAYING SURFACES AND SURFACES EXPOSED TO
FUEL PER 221.
C PRIME EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
D FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
FUEL PER 221.
FUEL PER 221.
APPROVAL.
CLAD OR 1000, 3000, 5000 OR 6000 SERIES ALUMINUM
FUEL PER 221.
C PRIME ONE COAT SPECIFIED SURFACES PER 202.
D PAINT PRIMED SURFACE WITH WHITE URETHANE COATING PER 222 (OR 274).
FUEL PER 221.
C PRIME ONE COAT SURFACES EXPOSED IN INLET DUCT PER 202.
D PAINT PRIMED SURFACE WITH WHITE URETHANE COATING PER 222 (OR 274).
F (INACTIVE FOR NEW DESIGN, SEE A430).
A-8

A440 BLACK EPOXY ENAMEL/BLACK URETHANE
C PAINT ALL SURFACES WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 234.
A441 PRIMER AND 16NXXXX FINISH
CLAD OR 1000, 3000, 5000 OR 6000 SERIES ALUMINUM ALLOYS
B PRIME ONE COAT ALL SURFACES PER 201.
C FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
B PRIME TWO COATS ON INTERIOR SURFACE PER 205 (OR 245).
E TOUCH UP AS REQUIRED PER 235, 242 AND 236.
B PRIME EXTERIOR EXPOSED SURFACE ONE COAT PER 202.
C PRIME TWO COATS ON INTERIOR SURFACE PER 205 (OR 245).
APPROVAL.
B PRIME TWO COATS ON SPECIFIED INTERIOR SURFACE PER 205 (OR 245).
A446 GRAY EPOXY ENAMEL/GRAY URETHANE AND 16NXXXX FINISH. EXPOSED
CASTINGS AND CLAD OR 1000, 3000, 5000 OR 6000 SERIES ALUMINUM ALLOYS
C PAINT WITH GRAY EPOXY ENAMEL OR GRAY URETHANE ON INTERIOR
SURFACE PER 211.
E TOUCH UP AS REQUIRED PER 235, 242,AND 238.
A-9

A447 GRAY EPOXY ENAMEL/GRAY URETHANE AND 16NXXXX FINISH
SURFACE PER 211.
E TOUCH UP AS REQUIRED PER 235, 242, AND 238.
A448 GRAY EPOXY ENAMEL/GRAY URETHANE AND 16NXXXX FINISH
B PRIME ONE COAT INTERIOR SURFACE PER 202.
SURFACE PER 211.
APPROVAL.
A449 BLACK EPOXY ENAMEL/BLACK URETHANE AND 16NXXXX FINISH. EXPOSED
C PAINT WITH BLACK EPOXY ENAMEL OR BLACK URETHANE ON INTERIOR
SURFACE PER 213.
A450 BLACK EPOXY ENAMEL/BLACK URETHANE AND 16NXXXX FINISH.
C PAINT WITH BLACK EPOXY ENAMEL OR BLACK URETHANE ON INTERIOR
SURFACE PER 213.
A - 10

A451 BLACK EPOXY ENAMEL/BLACK URETHANE AND 16NXXXX FINISH.
C PRIME EXTERIOR EXPOSED SURFACE ONE COAT PER 202.
D PAINT WITH BLACK EPOXY ENAMEL OR BLACK URETHANE ON INTERIOR
SURFACE PER 213.
E FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
F TOUCH UP AS REQUIRED PER 235 AND 239.
G (SEE A450 FOR PREFERRED CODE).
APPROVAL.
A452 P6096-2 FLAT BLACK URETHANE AND 16NXXXX FINISH - EXPOSED
C PAINT INTERIOR SURFACE WITH P6096-2 FLAT BLACK URETHANE PER 217 (OR 286).
A453 P6096-2 FLAT BLACK URETHANE AND 16NXXXX FINISH
EXPOSED BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS
C PAINT INTERIOR SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 217
(OR 286).
A454 P6096-2 FLAT BLACK URETHANE AND 16NXXXX FINISH
EXPOSED BARE 7000 SERIES AND 2219 ALUMINUM ALLOYS
D PAINT INTERIOR SURFACE WITH P6096-2 FLAT BLACK URETHANE PER 217.
APPROVAL.
A455 PRIMER. CLAD AND 1000, 3000, 5000, AND 6000
SERIES ALUMINUM ALLOYS (USE ONLY FOR ELECTRICAL
BONDING OF PARTS WITH STEEL INSERTS OR WIRE)
A BRUSH CHEM FILM EXPOSED SURFACES PER 178.
A - 11

A456 GRAY EPOXY ENAMEL/URETHANE. CLAD & 1000, 3000,
5000 & 6000 SERIES ALUMINUM (USE ONLY FOR ELEC.
BONDING OF PARTS WITH STEEL OR WIRE INSERTS)
C PAINT PRIMED SURFACES WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
A457 GRAY EPOXY ENAMEL/GRAY URETHANE
2000 AND 7000 SERIES ALUMINUM ALLOYS
(USE ONLY FOR CLOSE TOLERANCE MATING PARTS)
A ANODIZE ALL SURFACES PER 111. ALLOWS FOR ELECTRICAL BOND.
B PRIME ONE COAT SPECIFIED SURFACES PER 202.
C PAINT ONE COAT ON PRIMED SURFACES WITH GRAY EPOXY ENAMEL OR
GRAY URETHANE PER 211.
C PAINT ALL SURFACES WITH GRAY EPOXY ENAMEL OR GRAY URETHANE PER 227.
A459 GRAY EPOXY ENAMEL/GRAY URETHANE. CLAD, 1000, 3000, 5000, 6000
SERIES ALUMINUM ALLOYS AND CASTINGS
(USE ONLY FOR CLOSE TOLERANCE MATING PARTS)
C PAINT ONE COAT SPECIFIED SURFACES WITH GRAY EPOXY ENAMEL OR GRAY
URETHANE PER 211.
A460 WHITE URETHANE
CLAD OR 1000, 3000, 5000 AND 6000 SERIES ALUMINUM ALLOYS AND CASTINGS
C PAINT ALL SURFACES WITH WHITE URETHANE COATING PER 223 (OR 274).
A461 PRIMER AND WHITE URETHANE
B PRIME ONE COAT SURFACE REQUIRING WHITE COLOR PER 202.
C PAINT SPECIFIED SURFACE WITH WHITE URETHANE COATING PER 222 (OR 274).
D PRIME TWO COATS REMAINING SURFACE PER 205 (OR 245).
A - 12

B PRIME ONE COAT SURFACE REQUIRING WHITE COLOR PER 202.
D PRIME TWO COATS REMAINING SURFACE PER 205 (OR 245).
F (SEE A461 FOR PREFERRRED CODE).
APPROVAL.
A463 WHITE URETHANE AND 16NXXXX FINISH
CLAD OR 1000, 3000, 5000, AND 6000 SERIES ALUMINUM
C PAINT INTERIOR SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
D FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER THE
APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
A466 WHITE URETHANE
A - 13

A467 WHITE URETHANE
C PAINT WITH WHITE URETHANE COATING ALL SURFACES PER 223 (OR 274).
APPROVAL.
A468 WHITE URETHANE
BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS (FOR
ASSEMBLIES REQUIRING PRESS FITS)
B PRIME ONE COAT ON SPECIFIED SURFACES PER 202.
C PAINT WITH WHITE URETHANE COATING ON THE PRIMED SURFACES PER 222
(OR 274).
A469 WHITE URETHANE
BARE 7000 SERIES AND 2219 ALUMINUM ALLOYS (FOR
ASSEMBLIES REQUIRING PRESS FITS)
C PAINT WITH WHITE URETHANE COATING ON THE PRIMED SURFACES PER 222
(OR 274).
APPROVAL.
A - 14

A470 ALUMINUM TUBING ASSEMBLIES: GRAY EPOXY ENAMEL/GRAY URETHANE.
OXYGEN TUBING - EXPOSED IN CREW COMPARTMENT
A CHEM FILM, EXTERIOR SURFACE, PER 108.
B FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, PRIME ONE COAT
EXTERIOR SURFACE OF TUBING ASSEMBLY EXCEPT OMIT PRIMER .50
INCH FROM THE FACE OF THE FITTING UNLESS OTHERWISE SPECIFIED
ON THE DRAWING (OMIT 1.0 INCH MAXIMUM) PER 202.
C FOR TUBE ASSEMBLIES WITH "PERMASWAGE" OR "DYNATUBE" FITTINGS
PRIME ONE COAT EXTERIOR SURFACE OF TUBING ASSEMBLY, EXCEPT
OMIT PRIMER AS SPECIFIED PER 203.
D FOR TUBE ASSEMBLIES WITH FLARED FITTINGS (SLEEVE AND BT NUT)
PRIME ONE COAT EXTERIOR SURFACE OF TUBE TO THE BASE OF SLEEVE PER 272.
E FOR TUBE ASSEMBLIES WITH BEADED TUBE ENDS, PRIME ONE COAT
EXTERIOR SURFACE OF TUBING PER 272.
F PAINT PRIMED SURFACES WITH ONE COAT OF GRAY EPOXY ENAMEL OR GRAY
URETHANE PER 212.
G FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, TOUCH UP AS
REQUIRED PER 238; BUT TOUCH UP ACROSS A C7551 ASSEMBLED
JOINT IS NOT PERMITTED.
H FOR TUBE ASSEMBLIES WITH "PERMASWAGE", "DYNATUBE", OR FLARED
FITTINGS, TOUCH UP OR COMPLETE REQUIRED FINISH INCLUDING
ACROSS ASSEMBLED JOINT PER 238.
A471 ALUMINUM TUBING ASSEMBLIES - PRIMER
OXYGEN TUBING - NOT EXPOSED
A CHEM FILM EXTERIOR SURFACE PER 108.
TOUCH UP AS REQUIRED PER 242, BUT TOUCH UP ACROSS THE
ASSEMBLED JOINT IS NOT PERMITTED.
OMIT PRIMER AS SPECIFIED PER 203. AFTER INSTALLATION OR
COMPLETE REQUIRED FINISH INCLUDING ACROSS ASSEMBLED JOINT PER 242.
D FOR TUBE ASSEMBLIES WITH FLARED FITTINGS (SLEEVE AND BT
NUT), PRIME ONE COAT EXTERIOR SURFACE OF TUBE TO THE BASE OF
SLEEVE PER 272. AFTER INSTALLATION, TOUCH UP OR COMPLETE
REQUIRED FINISH INCLUDING ACROSS ASSEMBLED JOINT PER 242.
A472 PRIMER AND SOLID FILM LUBRICANT
B APPLY SOLID FILM LUBE TO SPECIFIED SURFACES PER 207.
C PRIME REMAINING SURFACES TWO COATS PER 205 (OR 245).
A - 15

A473 ALUMINUM TUBING ASSEMBLIES: WHITE URETHANE
5000 OR 6000 SERIES ALUMINUM ALLOYS
A CHEM FILM, EXTERIOR SURFACE ONLY, PER 108.
F PAINT PRIMED SURFACES WITH TWO COATS OF WHITE URETHANE COATING
PER 224.
G FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, TOUCH UP AS REQUIRED PER 237;
BUT TOUCH UP ACROSS A C7551 ASSEMBLED JOINT IS NOT PERMITTED.
A474 ALUMINUM TUBING ASSEMBLIES
5000 AND 6000 SERIES ALUMINUM ALLOYS LOCATED IN FUEL AREA
A PRIOR TO MECHANICALLY ATTACHING DETAILS OF ASSEMBLY AND
WHERE NO CREVICE EXISTS, HARD ANODIZE SPECIFIED SURFACES PER 115.
B ANODIZE REMAINING EXTERIOR SURFACES PER 140.
A - 16

A475 ALUMINUM TUBING ASSEMBLIES: GRAY EPOXY ENAMEL/GRAY URETHANE.
PNEUMATIC AND AIR DATA TUBING - EXPOSED IN CREW COMPARTMENT
F PAINT PRIMED SURFACES WITH ONE COAT OF GRAY EPOXY ENAMEL OR GRAY
URETHANE PER 212.
A476 ALUMINUM TUBING ASSEMBLIES: WHITE URETHANE COATING
PNEUMATIC, AIR DATA, HYDRAULICS, & FUEL TUBING.
EXTERIOR SURFACE OF TUBING ASSEMBLY EXCEPT OMIT PRIMER
.50 INCH FROM THE FACE OF THE FITTING UNLESS OTHERWISE SPEC-
IFIED ON THE DRAWING (OMIT 1.0 INCH MAXIMUM) PER 202.
C FOR TUBE ASSEMBLIES WITH "PERMASWAGE", "DYNATUBE", C20887, OR
C20963 FITTINGS, PRIME ONE COAT EXTERIOR SURFACE OF TUBING
ASSEMBLY, EXCEPT OMIT PRIMER AS SPECIFIED PER 203.
F PAINT PRIMED SURFACES WITH TWO COATS OF WHITE URETHANE COATING
PER 224.
H FOR TUBE ASSEMBLIES WITH "PERMASWAGE", "DYNATUBE", FLARED,
C20887, OR C20963 FITTINGS, TOUCH UP OR COMPLETE REQUIRED FINISH
INCLUDING ACROSS ASSEMBLED JOINT PER 237.
A - 17

A477 ALUMINUM TUBING ASSEMBLIES: AMS-C-27725 FUEL TANK
COATING. 5000 & 6000 SERIES AL ALLOY FUEL TUBING
& HOLLOW A356 AL FUEL CASTINGS LOCATED IN FUEL
A CHEM FILM EXTERIOR SURFACE ONLY PER 107.
B FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, APPLY AMS-C-27725
COATING TO EXTERIOR SURFACE OF TUBING ASSEMBLY EXCEPT OMIT
COATING .50 INCH FROM THE FACE OF THE FITTING UNLESS OTHER-
WISE SPECIFIED ON THE DRAWING (OMIT 1.0 INCH MAXIMUM) PER
221. TOUCH UP AS REQUIRED PER 240, BUT TOUCH UP ACROSS THE
APPLY AMS-C-27725 COATING TO EXTERIOR SURFACE OF TUBING
ASSEMBLY, EXCEPT OMIT COATING AS SPECIFIED PER 219.AFTER
INSTALLATION, TOUCH UP OR COMPLETE REQUIRED FINISH INCLUDING
APPLY AMS-C-27725 COATING ON EXTERIOR SURFACE OF TUBE TO THE
BASE OF SLEEVE PER 273. AFTER INSTALLATION, TOUCH UP OR
A478 ALUMINUM TUBING ASSEMBLIES: PRIMER
PNEUMATIC, AIR DATA, HYDRAULICS, AND FUEL TUBING
NOT IN FUEL OR SPECIAL COLOR AREA
IFIED ON THE DRAWING (OMIT 1.0 INCH MAXIMUM) PER 202. TOUCH
UP AS REQUIRED PER 242, BUT TOUCH UP ACROSS THE ASSEMBLED
C FOR TUBE ASSEMBLIES WITH "PERMASWAGE", "DYNATUBE", C20887, OR
C20963 FITTINGS PRIME ONE COAT EXTERIOR SURFACE OF TUBING
ASSEMBLY, EXCEPT OMIT PRIMER AS SPECIFIED PER 203. AFTER
PRIME ONE COAT EXTERIOR SURFACE OF TUBE TO THE BASE OF
SLEEVE PER 272. AFTER INSTALLATION, TOUCH UP OR COMPLETE
A - 18

A479 AL TUBING ASSY: PRIMER AND AMS-C-27725 FUEL TANK
COATING. 5000 & 6000 SERIES AL ALLOY FUEL TUBING,
LOCATED PARTIALLY IN FUEL AREA & PART OUTSIDE
B IN NON-FUEL AREA OF TUBE ASSEMBLIES WITH C7551 FITTINGS,
PRIME ONE COAT EXTERIOR SURFACE OF TUBING ASSEMBLY EXCEPT
OMIT PRIMER .50 INCH FROM THE FACE OF THE FITTING UNLESS
OTHERWISE SPECIFIED ON THE DRAWING (OMIT 1.0 INCH MAXIMUM),
PER 202. TOUCH UP AS REQUIRED PER 242, BUT TOUCH UP ACROSS
THE ASSEMBLED JOINT IS NOT PERMITTED.
C IN NON-FUEL AREA OF TUBE ASSEMBLIES WITH "PERMASWAGE" OR
"DYNATUBE" FITTINGS, PRIME ONE COAT EXTERIOR SURFACE OF TUB-
ING ASSEMBLY, EXCEPT OMIT PRIMER AS SPECIFIED PER 203. AFTER
D IN NON-FUEL AREA OF TUBE ASSEMBLIES WITH FLARED FITTINGS
(SLEEVE AND BT NUT), PRIME ONE COAT EXTERIOR SURFACE OF TUBE
TO THE BASE OF SLEEVE PER 272. AFTER INSTALLATION, TOUCH
UP OR COMPLETE REQUIRED FINISH INCLUDING ACROSS ASSEMBLED JOINT
PER 242.
E ON NOTED FUEL AREA OF TUBE ASSEMBLIES WITH C7551 FITTINGS,
ASSEMBLY EXCEPT OMIT COATING UNDER FITTING AND IN AREA
SPECIFIED ON DRAWING PER 221. TOUCH UP AS REQUIRED PER
240, BUT TOUCH UP ACROSS THE ASSEMBLED JOINT IS NOT PERMITTED.
F ON NOTED FUEL AREA OF TUBE ASSEMBLIES WITH "PERMASWAGE" OR
"DYNATUBE" FITTINGS, APPLY AMS-C-27725 COATING TO EXTERIOR
SURFACE OF TUBING ASSEMBLY EXCEPT OMIT COATING AS SPECIFIED
PER 219. AFTER INSTALLATION, TOUCH UP OR COMPLETE REQUAIRED
FINISH INCLUDING ACROSS ASSEMBLED JOINT PER 240.
G ON NOTED FUEL AREA OF TUBE ASSEMBLIES WITH FLARED FITTINGS
(SLEEVE AND BT NUT), APPLY AMS-C-27725 COATING ON EXTERIOR
SURFACE OF TUBE TO THE BASE OF SLEEVE PER 273. AFTER
A480 ALUMINUM TUBING ASSEMBLIES
5000 AND 6000 SERIES ALUMINUM ALLOYS LOCATED IN FUEL AREAS
WHERE NO CREVICE EXISTS, ANODIZE EXTERIOR SURFACES PER 140.
A481 ALUMINUM TUBING ASSEMBLIES: PRIMER AND 16NXXXX FINISH
5000, 6000 SERIES ALUMINUM ALLOYS
A ANODIZE OUTER SURFACES PER 140.
B PRIME ONE COAT OUTER SURFACE ONLY IN SPECIFIED AREAS PER 202
D FINISH SURFACE EXPOSED TO AIRPLANE EXTERIOR AFTER ASSEMBLY PER
DRAWING 16N0001.
A - 19

A482 ALUMINUM TUBING ASSEMBLIES: AMS-C-27725 FUEL TANK
COATING. 5000 & 6000 SERIES FUEL TUBING - LOCATED
IN FUEL AREAS-NO TREATMENT PERMITTED INSIDE
A BRUSH CHEM FILM EXTERIOR SURFACE ONLY, PER 108.
B FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, APPLY AMS-C-27725
COATING TO EXTERIOR SURFACE OF TUBING ASSEMBLY EXCEPT OMIT
COATING .50 INCH FROM THE FACE OF THE FITTING UNLESS OTHER-
WISE SPECIFIED ON THE DRAWING (OMIT 1.0 INCH MAXIMUM) PER
221. TOUCH UP AS REQUIRED PER 240, BUT TOUCH UP ACROSS THE
ASSEMBLY, EXCEPT OMIT COATING AS SPECIFIED PER 219. AFTER
INSTALLATION, TOUCH UP OR COMPLETE REQUIRED FINISH
INCLUDING ACROSS ASSEMBLIED JOINT PER 240.
APPLY AMS-C-27725 COATING ON EXTERIOR SURFACE OF TUBE TO THE
BASE OF SLEEVE PER 273. AFTER INSTALLATION, TOUCH UP OR
A483 ALUMINUM CASTINGS FOR FUEL TRANSMISSION: PRIMER
A356 ALUMINUM ALLOY CASTINGS TRANSMITTING FUEL IN A NON-FUEL AREA
A CHEM FILM EXTERIOR SURFACES PER 107.
B PRIME TWO COATS ON EXTERIOR NON-FUEL SURFACES PER 205 (OR 245).
A - 20

A484 ALUMINUM TUBING ASSEMBLIES: WHITE URETHANE AND
AMS-C-27725 FUEL TANK COATING. 5000 & 6000 SERIES
ALUMINUM AND A356 OR A357 ALUMINUM CASTINGS
B IN NON-FUEL AREA OF TUBE ASSEMBLIES WITH C7551 FITTINGS,
PRIME ONE COAT EXTERIOR SURFACE OF TUBING ASSEMBLY EXCEPT
OMIT PRIMER .50 INCH FROM THE FACE OF THE FITTING UNLESS
OTHERWISE SPECIFIED ON THE DRAWING (OMIT 1.0 INCH MAXIMUM), PER 202.
C IN NON-FUEL AREA OF TUBE ASSEMBLIES WITH "PERMASWAGE" OR
"DYNATUBE" FITTINGS, PRIME ONE COAT EXTERIOR SURFACE OF
TUBING ASSEMBLY, EXCEPT OMIT PRIMER AS SPECIFIED PER 203.
D IN NON-FUEL AREA OF TUBE ASSEMBLIES WITH FLARED FITTINGS
(SLEEVE AND BT NUT), PRIME ONE COAT EXTERIOR SURFACE OF
TUBE TO THE BASE OF SLEEVE PER 272.
E IN NON-FUEL AREA OF TUBE ASSEMBLIES PAINT PRIMED SURFACES
WITH TWO COATS OF WHITE URETHANE COATING PER 224.
F IN NON-FUEL AREA OF TUBE ASSEMBLIES WITH C7551 FITTINGS,
TOUCH UP AS REQUIRED PER 237; BUT TOUCH UP ACROSS A C7551
G IN NON-FUEL AREA OF TUBE ASSEMBLIES WITH "PERMASWAGE",
"DYNATUBE", OR FLARED FITTINGS, TOUCH UP OR COMPLETE
H ON NOTED FUEL AREA OF TUBE ASSEMBLIES WITH C7551 FITTINGS,
ASSEMBLY EXCEPT OMIT FUEL COATING .50 INCH FROM THE FACE OF
THE FITTING UNLESS OTHERWISE SPECIFIED ON THE DRAWING (OMIT
1.0 INCH MAXIMUM), PER 221. TOUCH UP AS REQUIRED PER 240,
BUT TOUCH UP ACROSS THE ASSEMBLED JOINT IS NOT PERMITTED.
I ON NOTED FUEL AREA OF TUBE ASSEMBLIES WITH "PERMASWAGE" OR
"DYNATUBE" FITTINGS, APPLY AMS-C-27725 COATING TO EXTERIOR
SURFACE OF TUBING ASSEMBLY EXCEPT OMIT COATING AS SPECIFIED PER 219.
AFTER INSTALLATION, TOUCH UP OR COMPLETE REQUIRED FINISH
J ON NOTED FUEL AREA OF TUBE ASSEMBLIES WITH FLARED FITTINGS
(SLEEVE AND BT NUT), APPLY AMS-C-27725 COATING ON EXTERIOR
SURFACE OF TUBE TO THE BASE OF SLEEVE PER 273. AFTER
INSTALLATION, TOUCH UP OR COMPLETE REQUIRED FINISH
A485 ALUMINUM TUBING ASSEMBLIES:
5000 OR 6000 ALUMINUM TUBING OR TUBING ASSEMBLIES
THAT ARE NOT DETAILS OF WELDED ASSEMBLIES
B PRIME EXTERIOR TUBE SURFACE, UNLESS OTHERWISE SPECIFIED, ONE COAT
PER 202.
C PAINT PRIMED SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
E (INACTIVE FOR NEW DESIGN).
A - 21

A486 ADHESIVE BONDED ASSEMBLY
A CHEM FILM ALL SPECIFIED EXPOSED ALUMINUM SURFACES PER 106 (OR PRIME
PER 300).
B PRIME INBOARD CLOSURE AND EXPOSED SURFACES OF FRONT SPAR
ONE COAT PER 202.
C PAINT EXPOSED SURFACES OF FRONT SPAR WITH WHITE URETHANE COATING
PER 222 (OR 274).
D PAINT INBOARD CLOSURE RIB WITH LIGHT GRAY URETHANE COATING
PER 254 (OR 276) FOR FSD AIRCRAFT (61, NO. 2 THRU NO. 6, 62:
NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE THE COLOR
OF URETHANE COATING SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT
PAINTING DRAWING.
E PRIME EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
F FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
G TOUCH UP AS REQUIRED PER 235, 236, 237, 242 AND 255 (FOR THE
GRAY COLOR ON FSD AIRCRAFT). TOUCH UP AS REQUIRED ON
PRODUCTION AIRCRAFT PER 235, 236, 237, 242 AND 298.
A CHEM FILM ALL SPECIFIED EXPOSED SURFACES PER 106 (OR PRIME PER 300).
B PRIME EXTERIOR COVE AREA AND OUTBOARD CLOSURE RIB ONE COAT PER 202.
C PRIME SPECIFIED SURFACES TWO COATS PER 205 (OR 245).
D PAINT COVE AREA WITH TWO COATS WHITE URETHANE COATING PER 222
(OR 274).
E PAINT INBOARD CLOSURE RIB WITH LIGHT GRAY URETHANE COATING
PER 254 (OR 276) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, 62:
PAINTING DRAWING.
F PRIME EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
G FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
H TOUCH UP AS REQUIRED PER 235, 236, 237, 242 AND 255 (FOR THE
PRODUCTION AIRCRAFT PER 235, 236, 237, 242, AND 298.
A - 22

A CHEM FILM ALL SPECIFIED SURFACES PER 106 (OR PRIME PER 300).
B PRIME INBOARD CLOSURE RIBS AND COVE AREA ONE COAT PER 202.
C PAINT COVE AREA WITH WHITE URETHANE COATING PER 222 (OR 274)
D PAINT INBOARD CLOSURE RIB WITH LIGHT GRAY URETHANE COATING
PER 254 (OR 276) FOR FSD AIRCRAFT (61: NO. 2 THRU 6, 62: NO.
1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE THE COLOR OF
URETHANE COATING SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT
PAINTING DRAWING.
F PRIME SPECIFIED SURFACES TWO COATS PER 205.
G FINISH EXTERIOR EXPOSED SURFACE AFTER ASSY PER DRAWING 16N0001.
H TOUCH UP AS REQUIRED PER 235, 236, 237, 242 AND 255 (FOR
THE GRAY COLOR ON FSD AIRCRAFT). TOUCH UP AS REQUIRED ON
PRODUCTION AIRCRAFT PER 235, 236, 237, 242 AND 298.
I (SEE R408 FOR ALTERNATE PRODUCTION METHOD).
A CHEM FILM ALL SPECIFIED SURFACES PER 106 (OR PRIME PER 300).
B PRIME INTERIOR SURFACE TWO COATS PER 205 (OR 245).
D APPLY SOLID FILM LUBRICANT TO AREAS SPECIFIED PER 207.
F TOUCH AS REQUIRED AT ASSY PER 235 AND 236.
G (INACTIVE FOR NEW DESIGN).
A490 WHITE URETHANE AND GRAY EPOXY ENAMEL/GRAY URETHANE
C PAINT ALL SURFACES, EXCEPT AREAS DESIGNATED TO BE GRAY, WITH
WHITE URETHANE COATING PER 222 (OR 274).
D PAINT SPECIFIED CREW COMPARTMENT AREA WITH GRAY EPOXY ENAMEL
OR GRAY URETHANE PER 211.
A491 PRIMER
B PRIME SPECIFIED SURFACES, TWO COATS PER 205 (OR 245).
A - 23

A492 PRIMER
(USE FOR PARTS WITH CLOSE TOLERANCE HOLES)
APPROVAL.
A493 WHITE URETHANE AND 16NXXXX FINISH. CLAD OR 1000,
3000, 5000, 6000 SERIES AL ALLOYS & CASTINGS.
(USE ONLY FOR CLOSE TOLERANCE PARTS AND HOLES)
B PRIME ONE COAT SPECIFIED INTERIOR SURFACE PER 202.
D PRIME EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
F TOUCH UP AS REQUIRED PER 237 OR 242.
7000 SERIES AND 2219 ALUMINUM ALLOY
(OMITTING ANODIZE IN SPECIFIED AREAS)
A SULFURIC ACID ANODIZE SPECIFIED AREAS PER 124.
B CHEM FILM AREAS NOT ANODIZED PER 134.
C PRIME SPECIFIED SURFACES TWO COATS PER 205 (OR 245).
D APPLY AMS-C-27725 COATING TO SPECIFIED FAYING SURFACE AND
APPROVAL.
7000 SERIES AND 2219 ALUMINUM ALLOY
(OMITTING ANODIZE IN SPECIFIED AREAS)
C APPLY AMS-C-27725 COATING TO ALL SURFACES PER 220.
APPROVAL.
A - 24

BONDED ASSYS OF ALL ALUMINUM ALLOYS
A CHEM FILM SPECIFIED INTERIOR SURFACES PER 106.
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER DRAWING 16N0001.
A497 LIGHT GRAY URETHANE AND 16NXXXX FINISH - PYLON
CLAD OR 1000, 3000, 5000, 6000 SERIES ALUMINUM ALLOYS AND CASTINGS
C PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT GRAY URETHANE
PER 254 (OR 276).
D FINISH EXTERIOR SURFACES AFTER ASSEMBLY PER DRAWING 16N0005.
E TOUCH UP AS REQUIRED PER 242, 246 OR 255.
PER 254 (OR 276).
E TOUCH-UP AS REQUIRED PER 242, 246, OR 255.
A499 PRIMER AND 16NXXXX FINISH - PYLON
B PRIME TWO COATS SPECIFIED SURFACES PER 205 (OR 245).
C PRIME ONE COAT REMAINING EXTERIOR SURFACES PER 202.
A500 LIGHT GRAY URETHANE AND 16NXXXX FINISH. CLAD OR
1000,3000,5000 OR 6000 SERIES ALLOYS & CASTINGS
PER 254 (OR 276).
A - 25

C PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT GRAY URETHANE PER 254
(OR 276).
E TOUCH-UP AS REQUIRED PER 242, 246, OR 255.
CLAD AND 1000, 3000, 5000, 6000 SERIES ALUMINUM ALLOYS AND
ALUMINUM CASTINGS
C PAINT ALL SURFACES WITH GRAY EPOXY ENAMEL OR GRAY URETHANE PER 227.
A503 WHITE URETHANE. CLAD,1000,3000,5000, 6000 SERIES
ALLOYS & ALUM. ALLOY CASTINGS (USE ONLY FOR CLOSE
MATING PARTS DETAILS OF VALVE ASSEMBLIES)
C PAINT PRIME SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
A504 PRIMER AND BLACK URETHANE
B PRIME EXPOSED SURFACES ONE COAT PER 202.
C PRIME SPECIFIED REMAINING SURFACES TWO COATS PER 205 (OR 245).
D PAINT EXPOSED SURFACES WITH BLACK URETHANE COATING PER 252.
E TOUCH UP AS REQUIRED PER 270.
A505 REWORK OF ANODIZED PART - WHITE URETHANE AND 16NXXXX FINISH.
ALL ALUMINUM ALLOYS
A CLEAN AND BRUSH CHEM FILM ALL ALUMINUM SURFACES PER 134.
B PRIME ONE COAT INTERIOR SURFACES PER 202.
C PAINT INTERIOR PRIMED SURFACES WITH WHITE URETHANE COATING PER 222
(OR 274).
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER DRAWING 16N0001.
A - 26

A506 WHITE URETHANE AND HARD ANODIZE
B BRUSH CHEM FILM TREAT AREAS NOT HARD ANODIZED, PER 134.
C ON SPECIFIED INTERIOR SURFACES PRIME ONE COAT PER 202.
D APPLY WHITE URETHANE COATING TO PRIMED INTERIOR SURFACES PER 222
(OR 274).
E TOUCH UP INTERIOR PER 237.
NOTE: AS AN OPTION, SPRAY LUBRICANT MAY BE
APPLIED TO THE HARD ANODIZE PER 230 TO ACHIEVE A UNIFORM APPEARANCE.
ALUMINUM CASTINGS
FUEL PER 221.
C PRIME TWO COATS ON INTERIOR NON-FUEL SURFACES PER 205 (OR 245).
A508 SOLID FILM LUBRICANT AND HARD ANODIZE
ALL ALUMINUM ALLOYS
B APPLY DRY SOLID FILM LUBRICANT TO SPECIFIED AREA PER 207.
A509 BLACK EPOXY ENAMEL/BLACK URETHANE AND HARD ANODIZE -
ALL ALUMINUM ALLOYS
C PAINT SPECIFIED SURFACES WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
7000 SERIES AND 2219 ALUMINUM ALLOYS (FOR PRESS FIT APPLICATIONS)
B PRIME ONE COAT ON SURFACES SPECIFIED FOR WHITE COLOR PER 202
D PRIME TWO COATS ON REMAINING SURFACES UNLESS OTHERWISE NOTED
PER 205 (OR 245).
APPROVAL.
A - 27

A511 16NXXXX FINISH
C PAINT ALL SURFACES WITH LIGHT GRAY URETHANE COATING PER 253
(OR 276) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, AND 62: NO.
1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE COLORS OF
URETHANE SPECIFIED ON APPLICABLE 16NXXXX PAINTING DRAWING.
D TOUCH-UP AS REQUIRED PER 255 (FOR THE GRAY COLOR ON FSD AIR-
CRAFT). TOUCH UP FOR PRODUCTION AIRCRAFT PER 298.
A512 16NXXXX FINISH
7000 SERIES AND 2219 ALUMINUM ALLOYS
(OR 276) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, AND 62: NO.
1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE COLORS OF
APPROVAL.
A513 16NXXXX FINISH
ALUMINUM CASTINGS AND 1000, 3000, 5000 AND 6000 SERIES AND CLAD
ALUMINUM ALLOYS
A CHEMICAL FILM ALL SURFACES PER 105.
C PAINT ALL SURFACES WITH LIGHT GRAY URETHANE COATING PER (253
OR 276) FOR FSD AIRCRAFT (16: NO. 2 THRU NO. 6, AND 62: NO.1
AND NO. 2). PRODUCTION AIRCRAFT SHALL USE COLORS OF
A514 16NXXXX FINISH
B PRIME ONE COAT ALL SURFACES SPECIFIED FOR LIGHT GRAY COLOR PER 202.
C PAINT SPECIFIED SURFACES WITH LIGHT GRAY URETHANE COATING
PER 254 (OR 276) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, AND
62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE COLORS
OF URETHANE SPECIFIED ON APPLICABLE 16NXXXX PAINTING DRAWING
A - 28

A515 16NXXXX FINISH
B PRIME ONE COAT SURFACES SPECIFIED FOR LIGHT GRAY COLOR PER 202.
62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE COLORS
OF URETHANE SPECIFIED ON APPLICABLE 16NXXXX PAINTING DRAWING
APPROVAL.
A516 16NXXXX FINISH - ALUMINUM CASTINGS AND 1000, 3000, 5000, 6000
SERIES AND CLAD ALUMINUM ALLOYS
PER 254 (OR 276) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6,
AND 62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE
COLORS OF URETHANE SPECIFIED ON APPLICABLE 16NXXXX PAINTING DRAWING.
ALUMINUM CASTINGS AND 1000, 3000, 5000, 6000
SERIES ALUMINUM ALLOYS
COATING PER 254 (OR 276) FOR FSD AIRCRAFT (61: NO. 2 THRU
NO. 6, AND 62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL
USE THE COLOR OF URETHANE COATING SPECIFIED ON THE APPLIC-
ABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
E TOUCH UP AS REQUIRED PER 242 AND 255 (FOR THE GRAY COLOR ON
FSD AIRCRAFT). TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 298.
A518 WHITE URETHANE AND BLACK EPOXY ENAMEL/BLACK URETHANE
D PAINT REMAINING SURFACES WITH BLACK EPOXY ENAMEL OR BLACK
URETHANE PER 213.
A - 29

A519 REWORK OF ANODIZED PART - WHITE URETHANE
ALL ALUMINUM ALLOYS
A520 REWORK OF ANODIZED PART - PRIMED
ALL ALUMINUM ALLOYS
A CLEAN AND BRUSH CHEM FILM ALL SURFACES PER 168.
ALUMINUM ALLOY CASTINGS (USE WITH CLOSE TOLERANCE HOLES)
B PRIME SPECIFIED INTERIOR SURFACES ONE COAT PER 202.
E FINISH EXTERIOR SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
F TOUCH UP AS REQUIRED PER 235, 237 AND 242.
A522 DARK GRAY URETHANE
C PAINT ALL SURFACES WITH DARK GRAY URETHANE COATING PER 263.
APPROVAL.
B PRIME ONE COAT SURFACES SPECIFIED FOR DARK GRAY COLOR PER 202.
C PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE PER 257.
APPROVAL.
A - 30

A524 16NXXXX FINISH
CLAD AND 1000, 3000, 5000, AND 6000 SERIES
ALUMINUM ALLOYS AND ALUMINUM ALLOY CASTINGS
C PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE COATING PER
257 (OR 277) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, AND 62:
PAINTING DRAWING.
A526 BLACK EPOXY ENAMEL/BLACK URETHANE AND
BLACK DYE ANODIZE FOR THERMAL CONTROL.
ALL ALUMINUM WROUGHT AND CAST ALLOYS
C PAINT PRIMED SURFACES WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
A527 PRIMER AND BLACK DYE ANODIZE FOR THERMAL CONTROL
FOR CLAD OR 1000, 3000, 5000 AND 6000 SERIES ALUMINUM ALLOYS
A528 REWORK OF ANODIZED PART - 16NXXXX FINISH
ALL ALUMINUM ALLOYS
A CLEAN AND BRUSH CHEM FILM ALL ALUMINUM PER 134.
C PAINT PRIMED SURFACES WITH DARK GRAY URETHANE COATING PER
257 (OR 277) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, AND 62:
OR URETHANE COATING SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT
PAINTING DRAWING.
D TOUCH-UP AS REQUIRED PER 258 (FOR THE GRAY COLOR ON FSD
AIRCRAFT). TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 298.
BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS (CLOSE TOLERANCE FITS)
PER 213.
A - 31

PER 234.
APPROVAL.
A531 GRAY EPOXY ENAMEL/GRAY URETHANE AND HARD ANODIZE
ALL ALUMINUM ALLOYS
PER 211.
(FOR USE WITH CLOSE TOLERANCE HOLES)
PER 213.
APPROVAL.
A533 ORANGE-YELLOW EPOXY ENAMEL/ORANGE-YELLOW URETHANE
AND HARD ANODIZE - ALL ALUMINUM ALLOYS
C PAINT PRIMED SURFACES WITH ORANGE-YELLOW EPOXY ENAMEL OR
A535 P6096-2 FLAT BLACK URETHANE
C PAINT ALL SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 266 (OR 286).
A - 32

B SULFURIC ACID ANODIZE REMAINING SURFACES PER 124.
APPROVAL.
C PRIME ONE COAT SURFACES REQUIRING WHITE COLOR PER 202.
D PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
A538 PAINTING OF EXISTING ZINC CHROMATE-PRIMED ALUM. PARTS –
16NXXXX FINISH.
ALL PRIMED ALUMINUM ALLOY MATERIALS
A CLEAN AREAS SPECIFIED FOR PAINTING BY SOLVENT WIPING WITH
TT-N-95 NAPHTHA OR BRULIN SAFETY SOLVENT NO. 512.
B LIGHTLY ABRADE PRIMED AREAS OF SURFACES SPECIFIED FOR
PAINTING WITH #320 OR FINER ABRASIVE SUCH AS ALUMINUM OXIDE
OR EMERY CLOTH.
C RE-WIPE ABRADED SURFACE PER (A) ABOVE.
D BRUSH CHEMICAL FILM ANY UNPRIMED AREAS OF ALUMINUM REQUIRED
TO BE PAINTED PER 134.
E APPLY ONE COAT PRIMER TO SURFACES REQUIRING PAINT, PER 202.
F PAINT PRIMED SURFACES WITH DARK GRAY URETHANE COATING PER
257 (OR 277 FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, AND 62:
PAINTING DRAWING.
G TOUCH-UP AS REQUIRED PER 260 (FOR THE GRAY COLOR ON FSD AIR-
CRAFT). TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 298
H (INACTIVE FOR NEW DESIGN).
A - 33

A539 16NXXXX FINISH
BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS (TAIL HOOK COMPARTMENT)
C PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE COATING PER
257 (OR 277) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, AND
62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE THE
COLOR OF URETHANE COATING SPECIFIED AS APPLICABLE 16NXXXX AIRCRAFT
PAINTING DRAWING.
A540 BLACK EPOXY ENAMEL/BLACK URETHANE -
ALUMINUM ALLOY CASTINGS (FOR CLOSE TOLERANCE FITS)
B PRIME ONE COAT SURFACES SPECIFIED FOR BLACK COLOR PER 202.
PER 213.
CLAD, 1000, 3000, 5000, OR 6000 ALUMINUM ALLOYS
(INCLUDING TUBING FOR DRAIN APPLICATIONS)
B APPLY AMS-C-27725 COATING ON SPECIFIED SURFACES PER 221.
BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS (FOR
PRESS FITS AND CLOSE TOLERANCE APPLICATIONS)
A543 16NXXXX FINISH
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUM.
ALLOYS (FOR CLOSE FIT APPLICATIONS)
C PAINT PRIMED SURFACES WITH DARK GRAY URETHANE COATING
COLOR OF URETHANE COATING SPECIFIED ON APPLICATION 16NXXXX
AIRCRAFT PAINTING DRAWING.
CRAFT). TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 298
A - 34

ALL ALUMINUM ALLOYS
B APPLY SOLID FILM LUBE TO ALL SURFACES PER 228 IN THICKNESSES
OR DIMENSIONS AS NOTED.
A545 16NXXXX FINISH
CLAD 1000, 3000, 5000, 6000 SERIES ALUM. ALLOYS
AND ALUMINUM ALLOY CASTINGS
C PAINT ALL SURFACES WITH DARK GRAY TEFLON-URETHANE COATING
PER 267 (OR 288) FOR FSD AIRCRAFT (61: NO.2 THRU NO. 6 AND
COLOR OF TEFLON URETHANE COATING SPECIFIED ON APPLICABLE
16NXXXX AIRCRAFT PAINTING DRAWING.
D TOUCH UP AS REQUIRED PER 260 (FOR THE GRAY COLOR ON FSD
AIRCRAFT). TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 298.
B PRIME INTERIOR SURFACES TWO COATS PER 205 (OR 245).
C PRIME ONE COAT ON EXTERIOR SURFACES PER 202.
D PAINT EXTERIOR SURFACES WITH LIGHT GRAY TEFLON-URETHANE
NO. 6 AND 62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL
USE THE COLOR OF TEFLON-URETHANE COATING SPECIFIED ON
APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING. (OVERSPRAY
ONTO FAYING SURFACE IS NOT PERMITTED.)
E TOUCH UP AS REQUIRED PER 236 OR 262 FOR GRAY COLOR ON FSD
AIRCRAFT. TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 236 OR 298.
B PRIME TWO COATS ON INTERIOR SURFACES PER 205 (OR 245).
C PRIME ONE COAT ON EXTERIOR SURFACES PER 202.
D PAINT SPECIFIED EXTERIOR SURFACE WITH DARK GRAY TEFLON-
URETHANE COATING PER 259 (OR 288) FOR FSD AIRCRAFT (61: NO.
2 THRU NO. 6, AND 62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT
SHALL USE THE COLOR OF TEFLON-URETHANE COATING SPECIFIED ON
E FINISH REMAINING EXTERIOR SURFACES AFTER ASSEMBLY PER DRAWING
16N0001.
F TOUCH UP AS REQUIRED PER 236, 242 AND 260 (FOR THE GRAY
COLOR OF FSD AIRCRAFT). TOUCH UP AS REQUIRED ON PRODUCTION
AIRCRAFT PER 236, 242, OR 298.
A - 35

A548 P6096-2 BLACK URETHANE AND GRAY EPOXY ENAMEL/GRAY URETHANE.
CLAD, 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS & CASTINGS.
B PRIME SURFACES REQUIRING BLACK OR GRAY COLOR ONE COAT PER 202.
C PAINT SPECIFIED SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 217
(OR 286)
D PAINT SPECIFIED SURFACES WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
A549 AMS-C-27725 FUEL TANK COATING AND BLACK EPOXY ENAMEL/
BLACK URETHANE - BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS
B APPLY FUEL TANK COATING AMS-C-27725 TO FAYING SURFACES AND
C PRIME ONE COAT TO SURFACES SPECIFIED FOR BLACK EPOXY PER 202
D PAINT SPECIFIED SURFACES WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
A550 AMS-C-27725 FUEL TANK COATING AND GRAY EPOXY
ENAMEL/GRAY URETHANE
BARE 2000 AND 7000 SERIES ALUM. ALLOYS
D PAINT PRIMED SURFACES WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
A551 ORANGE-YELLOW EPOXY ENAMEL/ORANGE-YELLOW URETHANE
EMERGENCY EXITS & RELEASES: CLAD OR 1000, 3000,
5000 OR 6000 SERIES ALUMINUM ALLOYS & CASTINGS
C PAINT ALL SURFACES WITH ORANGE-YELLOW EPOXY ENAMEL OR
A552 AMS-C-27725 FUEL TANK COATING & GRAY EPOXY ENAMEL/GRAY UETHANE
PER 211.
APPROVAL.
A - 36

B PRIME ONE COAT INTERIOR SURFACES PER 202.
D PAINT INTERIOR SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY. PER DRAWING 16N0001.
F TOUCH UP PER 235 AND 237.
APPROVAL.
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUM. ALLOYS AND
ALUMINUM CASTINGS
PER 234.
A555 GRAY EPOXY ENAMEL/GRAY URETHANE AND SOLID FILM LUBRICANT.
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND CASTINGS.
C PRIME SPECIFIED SURFACES ONE COAT PER 202.
D PAINT PRIMED SURFACES ONE COAT OF GRAY EPOXY ENAMEL OR GRAY
URETHANE PER 211.
C APPLY AMS-C-27725 COATING ON FAYING SURFACES AND SURFACES EXPOSED
TO FUEL PER 221.
D PRIME EXPOSED SURFACES ONE COAT PER 202.
E PAINT PRIMED SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
APPROVAL.
A557 SOLID FILM LUBRICANT
(CLOSE FITTING OR THREADED PARTS)
A - 37

A558 P6096-2 FLAT BLACK URETHANE & SOLID FILM LUBRICANT
D PAINT PRIMED SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 217 (OR 286).
(FOR CLOSE TOLERANCE FITS)
C PAINT PRIMED SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 217 (OR 286).
A560 P6096-2 FLAT BLACK URETHANE AND HARD ANODIZE
1000, 3000, 5000, AND 6000 SERIES AND CLAD ALUMINUM AND CASTINGS
A HARD ANODIZE ALL SURFACES EXCEPT THREADS PER 115.
B CHEM FILM UNANODIZED THREADS PER 105.
A561 PRIMER AND SOLID FILM LUBRICANT
CLAD AND 1000, 3000, 5000, 6000 SERIES ALUMINUM ALLOYS
B APPLY SOLID FILM LUBE TO EXPOSED SURFACES IN THICKNESS OR DIMENSIONS
AS NOTED PER 207.
A562 PRIMER
A SULFURIC ACID ANODIZE SPECIFIED SURFACES PER 124.
B CHEM FILM UNANODIZED SURFACES PER 134.
C PRIME ALL SURFACES TWO COATS PER 204.
APPROVAL.
A563 PRIMER
USE ONLY FOR 2024 SHIM MATERIAL
A BRUSH CHEM FILM TREAT PER 168.
B PRIME TWO COATS ALL SURFACES PER 204 (OR 245).
C (INACTIVE FOR NEW DESIGN).
A - 38

(CLOSE TOLERANCE APPLICATIONS)
B PRIME ONE COAT SURFACES SPECIFIED FOR DARK GRAY COLOR PER 202.
C PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE PER 257 (OR 277).
A566 PRIMER AND WHITE URETHANE.
BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS (CAN BE
USED FOR CLOSE TOLERANCE APPLICATIONS)
B PRIME ONE COAT ON SURFACES SPECIFIED FOR WHITE COLOR PER 202
D PRIME TWO COATS ON REMAINING SURFACES, UNLESS OTHERWISE NOTED,
PER 205 (OR 245).
A567 16NXXXX FINISH
NO. 6, 62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL USE
THE COLOR OF URETHANE COATING SPECIFIED ON APPLICABLE
E TOUCH UP AS REQUIRED PER 235, 242 AND 255 (FOR THE GRAY
COLOR ON FSD AIRCRAFT). TOUCH UP AS REQUIRED ON PRODUCTION
AIRCRAFT PER 235, 242 OR 298.
A568 PRIMER AND BLACK EPOXY ENAMEL
B PRIME SPECIFIED INTERIOR SURFACE ONE COAT PER 202.
C PRIME SPECIFIED EXPOSED SURFACE ONE COAT PER 202.
D PAINT PRIMED EXPOSED SURFACE WITH BLACK EPOXY ENAMEL OR
BLACK URETHANE PER 213.
A - 39

B APPLY SOLID FILM LUBE TO ALL SURFACES PER 228 IN THICKNESSES OR
DIMENSIONS AS NOTED.
ALUM. CASTINGS AND CLAD OR 1000, 3000, 5000 OR 6000 SERIES
ALUMINUM ALLOYS
C PAINT ALL SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 266 (OR 286).
A571 P6096-2 FLAT BLACK URETHANE. ALUMINUM CASTINGS,
CLAD OR 1000,3000,5000,OR 6000 SERIES ALUM. ALLOYS
(FOR TIGHT FIT OR ELECTRICAL BOND APPLICATIONS)
C PAINT PRIME SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 217 (OR 286).
A572 GRAY EPOXY ENAMEL/GRAY URETHANE – 1000,
3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND
ELECTRICAL BONDING ON 2000 & 7000 SERIES ALUM.
C PAINT ONE COAT PRIMED SURFACES WITH GRAY EPOXY ENAMEL OR
GRAY URETHANE PER 211.
BARE 2000 & 7000 SERIES ALUMINUM ALLOYS
B PRIME INTERIOR SURFACES TWO COATS PER 205 (OR 245).
C PRIME EXTERIOR SURFACES ONE COAT PER 202.
D PAINT EXTERIOR SURFACES WITH DARK GRAY TEFLON-URETHANE
THE COLOR OF TEFLON-URETHANE COATING SPECIFIED ON APPLICABLE
16NXXXX AIRCRAFT PAINTING DRAWING. (OVERSPRAY OF THE TEFLON
-URETHANE COATING ONTO FAYING SURFACES IS NOT PERMITTED.)
E TOUCH UP AS REQUIRED PER 236 OR 260 (FOR THE GRAY COLOR ON
FSD AIRCRAFT). TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT
PER 236 OR 298.
A - 40

A574 16NXXXX FINISH
OF URETHANE COATING SPECIFIED ON THE APPLICABLE 16NXXXX AIRCRAFT
PAINTING DRAWING.
D TOUCH UP AS REQUIRED PER 236 AND 255 (FOR THE GRAY COLOR ON
PER 236 AND 298.
A575 PRIMER AND LIGHT GRAY URETHANE
C PAINT SPECIFIED SURFACES WITH LIGHT GRAY URETHANE COATING PER 254
(OR 276).
D PRIME TWO COATS REMAINING SURFACES UNLESS OTHERWISE SPECIFIED PER 205
(OR 245).
APPROVAL.
PAINTING DRAWING.
D PRIME TWO COATS REMAINING SURFACES, UNLESS OTHERWISE SPECIFIED,
PER 205 (OR 245).
E TOUCH UP AS REQUIRED PER 236 AND 255 (FOR THE GRAY COLOR
ON FSD AIRCRAFT). TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT
PER 236 AND 298.
A - 41

A577 AMS-C-27725 FUEL TANK COATING AND 16NXXXX
B APPLY AMS-C-27725 COATING ON SPECIFIED FAYING SURFACE AND
C PRIME ONE COAT EXTERIOR SURFACES REQUIRING LIGHT GRAY COLOR PER 202.
D PAINT SPECIFIED EXTERIOR SURFACES WITH LIGHT GRAY URETHANE
THE COLOR OF URETHANE COATING SPECIFIED ON THE APPLICABLE
E TOUCH UP AS REQUIRED PER 240 AND 255 (FOR THE GRAY COLOR
ON FSD AIRCRAFT). TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT
PER 240 AND 298.
A578 DARK GRAY URETHANE. ALUM. ALLOY CASTINGS & CLAD,
1000,3000,5000, OR 6000 SERIES ALUMINUM ALLOYS &
ELECTRICAL BONDING ON 2000 & 7000 SERIES ALUMINUM
C PAINT PRIMED SURFACES WITH DARK GRAY URETHANE COATING PER 257
(OR 277).
A579 REWORK OF ANODIZED PART - GRAY EPOXY ENAMEL/
GRAY URETHANE. ALL ALUMINUM ALLOYS
PER 211.
A580 LUSTERLESS BLACK URETHANE
C PAINT ALL SURFACES WITH LUSTERLESS BLACK URETHANE COATING PER 279
(OR 281).
CLAD & 1000,3000,5000, & 6000 SERIES ALUM. ALLOYS
AND ALUMINUM CASTINGS (FOR CLOSE TOLERANCE FITS)
C PAINT PRIMED SURFACES WITH LUSTERLESS BLACK URETHANE COATING PER 283
(OR 281).
A - 42

CLAD AND 1000, 3000, 5000, AND 6000 SERIES ALUMINUM AND
ALUMINUM CASTINGS
(OR 281).
A583 AMS-C-27725 FUEL TANK COATING AND LUSTERLESS BLACK URETHANE
C PRIME NON-FUEL SURFACES ONE COAT PER 202.
D PAINT PRIMED SURFACES WITH LUSTERLESS BLACK URETHANE COATING PER 283
(OR 281).
E TOUCH UP AS REQUIRED PER 240 OR 285.
(OR 281).
A585 LUSTERLESS BLACK URETHANE AND 16NXXXX FINISH
C PAINT INTERIOR SURFACES WITH LUSTERLESS BLACK URETHANE COATING
PER 283 (OR 281).
E TOUCH UP AS REQUIRED PER 235, 242, OR 285.
A586 LUSTERLESS BLACK URETHANE AND 16NXXXX FINISH
CLAD OR 1000, 3000, 5000, AND 6000 SERIES ALUMINUM ALLOYS OR
ALUMINUM CASTINGS
PER 283 (OR 281).
A - 43

A587 LUSTERLESS BLACK URETHANE AND HARD ANODIZE
ALL ALUMINUM ALLOYS
C PAINT SPECIFIED SURFACES WITH LUSTERLESS BLACK URETHANE COATING
PER 283 (OR 281).
A588 REWORK OF ANODIZE PART - LUSTERLESS BLACK URETHANE
ALL ALUMINUM ALLOYS
(OR 281).
A589 LUSTERLESS GRAY URETHANE AND HARD ANODIZE
ALL ALUMINUM ALLOYS
C PAINT PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE COATING PER 282
(OR 280).
A590 LUSTERLESS GRAY URETHANE
CLAD AND 1000, 3000, 5000, & 6000 SERIES ALUMINUM ALLOYS AND
ALUMINUM CASTINGS
C PAINT ALL SURFACES WITH LUSTERLESS GRAY URETHANE COATING PER 278
(OR 280).
C PAINT ALL SURFACES WITH LUSTERLESS GRAY URETHANE COATING PER 278
(OR 280).
A592 AMS-C-27725 FUEL TANK COATING AND LUSTERLESS GRAY URETHANE
FUEL PER 221.
C PRIME NON-FUEL SURFACES ONE COAT PER 202.
D PAINT PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE COATING PER 282
(OR 280).
A - 44

A593 WHITE URETHANE AND LUSTERLESS GRAY URETHANE
D PAINT SPECIFIED SURFACES WITH LUSTERLESS GRAY URETHANE COATING
PER 282 (OR 280).
E TOUCH-UP AS REQUIRED PER 237 OR 284.
A594 LUSTERLESS GRAY URETHANE AND 16NXXXX FINISH
C PAINT INTERIOR SURFACES WITH LUSTERLESS GRAY URETHANE COATING
PER 282 (OR 280).
A595 LUSTERLESS GRAY URETHANE AND 16NXXXX FINISH
CLAD & 1000,3000,5000, & 6000 SERIES ALUM. ALLOYS
AND ALUMINUM CASTINGS (FOR CLOSE TOLERANCE FITS)
C PAINT INTERIOR SURFACES WITH LUSTERLESS GRAY URETHANE COATING
PER 282 (OR 280).
A596 WHITE URETHANE AND LUSTERLESS BLACK URETHANE
D PAINT REMAINING SURFACES WITH LUSTERLESS BLACK URETHANE COATING
PER 283 (OR 281).
C PAINT ALL SURFACES WITH P6096-2 FLAT BLACK URETHANE COATING PER 266
(OR 286).
A - 45

A598 PRIMER AND LUSTERLESS GRAY URETHANE
C PRIME ONE COAT SURFACES SPECIFIED FOR GRAY COLOR PER 202.
D PAINT SPECIFIED SURFACES WITH LUSTERLESS GRAY URETHANE PER 282 (OR 280).
A599 BLACK EPOXY ENAMEL/BLACK URETHANE. CLAD OR
1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND CASTINGS
PER 213.
A600 WHITE URETHANE AND LUSTERLESS BLACK URETHANE
CLAD AND 1000, 3000, 5000 AND 6000 SERIES ALUMINUM
ALLOYS AND ALUMINUM ALLOY CASTINGS
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222 (OR 274).
D PAINT REMAINING SURFACES WITH LUSTERLESS BLACK URETHANE PER 283
(OR 281).
A601 LUSTERLESS GRAY URETHANE AND HARD ANODIZE
ALL ALUMINUM ALLOYS
B BRUSH CHEM FILM NON-HARD ANODIZED SURFACES PER 134.
C PRIME ONE COAT NON-HARD ANODIZED SURFACES PER 202.
D PAINT PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE COATING PER 282
(OR 280).
C PAINT PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE COATING PER 282
(OR 280).
A - 46

ALUMINUM CASTINGS & 1000, 3000, 5000, 6000 SERIES
& CLAD ALUMINUM ALLOYS (FOR CLOSE TOLERANCE FITS)
C PAINT PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE COATING
PER 282 (OR 280).
A604 P6096-2 FLAT BLACK URETHANE. CLAD & 1000,3000,5000
AND 6000 SERIES ALUMINUM ALLOYS (FOR ELECTRICALLY
BONDED AREAS OR FOR CLOSE FIT TOLERANCE PARTS)
A CHEMICAL FILM ALL SURFACE PER 176.
C PAINT EXPOSED SURFACES WITH P6096-2 FLAT BLACK URETHANE
PER 217 (OR 286).
A605 DARK GRAY URETHANE. CLAD OR 1000, 3000, 5000 OR
6000 SERIES ALUMINUM ALLOYS OR ALUMINUM CASTINGS
(FOR CLOSE FIT TOLERANCE PARTS OR ELECTRICAL BOND)
PER 257 (OR 277).
A606 WHITE URETHANE AND LUSTERLESS GRAY URETHANE
CLAD AND 1000, 3000, 5000 AND 6000 SERIES ALUMINUM ALLOYS AND
ALUMINUM CASTINGS
D PAINT REMAINING SURFACES WITH LUSTERLESS GRAY URETHANE COATING
PER 282 (OR 280).
A607 REWORK OF CURED PRIMER - GRAY EPOXY ENAMEL/GRAY URETHANE.
ALL ALUMINUM ALLOYS COVERED WITH CURED PRIMER
A CLEAN AND ACTIVATE CURED PRIMER PER 174.
B PAINT ALL SURFACES WITH GRAY EPOXY ENAMEL OR GRAY URETHANE PER 227.
B PRIME ONE COAT ON SPECIFIED INTERIOR SURFACES AND EXTERIOR SURFACES
PER 202.
C FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
A - 47

A609 GRAY URETHANE
C PAINT ALL SURFACES WITH GRAY COLOR 36270 URETHANE COATING
PER 289 (OR 292).
A610 GRAY URETHANE
(FOR CLOSE FIT TOLERANCES)
C PAINT PRIMED SURFACES WITH GRAY COLOR 36270 URETHANE COATING
PER 290 (OR 292).
A611 REWORK OF ANODIZED PART - GRAY URETHANE AND 16NXXXX FINISH.
ALL ALUMINUM ALLOYS
A CLEAN AND BRUSH CHEM FILM ALUMINUM SURFACES REQUIRING PRIMER
PER 134.
B PRIME ONE COAT SPECIFIED INTERIOR SURFACES PER 202.
C PAINT SPECIFIED SURFACES WITH GRAY COLOR 36270 URETHANE COATING
PER 290 (OR 292).
A612 GRAY URETHANE AND 16NXXXX FINISH
PER 290 (OR 292).
A613 PRIMER AND GRAY URETHANE
B PRIME ONE COAT SURFACES SPECIFIED FOR GRAY COLOR PER 202.
C PRIME TWO COATS REMAINING SURFACES PER 205 (OR 245).
D PAINT SPECIFIED SURFACES WITH GRAY COLOR 36270 URETHANE COATING
PER 290 (OR 292).
A - 48

A614 WHITE ACRYLIC LACQUER/WHITE URETHANE
CLAD OR 1000, 3000, 5000 OR 6000 SERIES ALUMINUM ALLOYS AND CASTINGS
C PAINT ALL SURFACES WITH EITHER WHITE ACRYLIC LACQUER OR
A615 PRIMER AND WHITE ACRYLIC LACQUER/WHITE URETHANE
C PAINT SPECIFIED SURFACES WITH EITHER WHITE ACRYLIC LACQUER
OR WHITE URETHANE COATING PER 294 (OR 296).
D TOUCH-UP AS REQUIRED PER 295.
(FOR CLOSE FIT TOLERANCES)
C PAINT PRIMED SURFACES WITH EITHER WHITE ACRYLIC LACQUER OR
A618 WHITE ACRYLIC LACQUER/WHITE URETHANE. CLAD & 1000
3000,5000 & 6000 SERIES ALUM ALLOY & CASTINGS (FOR
DETAIL OF VALVE ASSEMBLY & FOR ELECTRICAL BONDING)
C PAINT PRIMED SURFACES WITH EITHER WHITE ACRYLIC LACQUER OR
A619 REWORK OF ANODIZED PART - WHITE ACRYLIC LACQUER/WHITE URETHANE.
ALL ALUMINUM ALLOYS
PER 134.
C PAINT PRIME SURFACES WITH EITHER WHITE ACRYLIC LACQUER OR
A - 49

A620 ALUM TUBING ASSEMBLY - WHITE ACRYLIC LACQUER/WHT
URETHANE. PNEUMATIC, AIR DATA, HYDRAULICS & FUEL
TUBING-EXPOSED IN AVIONIC-ELECTRONIC COMPARTMENTS.
F PAINT PRIMED SURFACE WITH EITHER WHITE ACRYLIC LACQUER OR
G FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, TOUCHING UP AS
H FOR TUBE ASSEMBLIES WITH "PERMASWAGE", "DYNATUBE", OR
FLARED FITTINGS, TOUCH UP OR COMPLETE REQUIRED FINISH
I FOR TUBE OR WELDED ASSEMBLIES CONTAINING SEALED DOORS,
FINISH (CHEM FILM, PRIME, AND PAINT) SHOULD BE OMITTED FROM
SURFACE OF GASKET.
A621 WHITE URETHANE AND WHITE ACRYLIC LACQUER/WHITE URETHANE
C PAINT SURFACES SPECIFIED FOR WHITE URETHANE COATING PER 222 (OR 274).
D PAINT REMAINING SURFACES WITH EITHER WHITE ACRYLIC LACQUER
A622 WHITE ACRYLIC LACQUER/WHITE URETHANE & LUSTERLESS
GRAY URETHANE
D PAINT REMAINING SURFACES WITH LUSTERLESS GRAY URETHANE COATING
PER 282 (OR 280).
A - 50

A623 WHITE ACRYLIC LACQUER/WHITE URETHANE AND 16NXXXX FINISH
C PAINT INTERIOR SURFACES WITH EITHER WHITE ACRYLIC LACQUER OR
A624 WHITE ACRYLIC LACQUER/WHITE URETHANE AND
LUSTERLESS BLACK URETHANE
D PAINT REMAINING SURFACES WITH LUSTERLESS BLACK URETHANE COATING
PER 283 (OR 281).
A625 AMS-C-27725 FUEL TANK COATING AND WHITE ACRYLIC
LACQUER/WHITE URETHANE
D PAINT REMAINING SURFACES WITH EITHER WHITE ACRYLIC LACQUER
A626 PRIMER AND WHITE ACRYLIC LACQUER/WHITE URETHANE
B PRIME TWO COATS SURFACES NOT REQUIRING WHITE COLOR PER 205 (OR 245).
C PRIME ONE COAT SURFACES REQUIRING WHITE COLOR PER 202.
D PAINT SPECIFIED SURFACES WITH EITHER WHITE ACRYLIC LACQUER
A627 WHITE ACRYLIC LACQUER/WHITE URETHANE AND 16NXXXX
CLAD AND 1000, 3000, 5000 AND 6000 SERIES ALUMINUM ALLOYS AND CASTINGS
A - 51

A628 REWORK OF ANODIZED PARTS - WHITE ACRYLIC
LACQUER/WHITE URETHANE AND 16NXXXX.
ALL ALUMINUM ALLOYS
PER 134.
D PRIME ONE COAT EXTERIOR EXPOSED SURFACES PER 202.
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
A629 SHIM MATERIAL - AMS-C-27725 FUEL TANK COATING
USE ONLY FOR 2024 MATERIAL
A BRUSH CHEM FILM TREAT PER 168.
B APPLY AMS-C-27725 COATING TO ALL SURFACES PER 220.
D (INACTIVE FOR NEW DESIGN).
BARE 2000 AND 7000 SERIES ALLOYS
B PRIME ONE COAT ALL SURFACES EXCEPT HINGE PIN HOLES PER 202.
C ADDITIONALLY PAINT INTERIOR SURFACES AFTER ASSEMBLY PER ASSEMBLY
FINISH CODE.
D FINISH EXTERIOR SURFACES AFTER ASSEMBLY PER 16N0001.
FOR HINGED DOOR ASSEMBLIES, MINUS THE LATCHES
A CLEAN AND PREPARE EXPOSED INTERIOR SURFACES OF THE DOOR AND HINGE
PER 297.
B PRIME THE EXPOSED INTERIOR SURFACES ONE COAT PER 202 (OVER-
SPRAY ON PRIMED ATTACHED DETAILS PERMITTED).
C FINISH EXTERIOR SURFACES AFTER ASSEMBLY PER 16N0001.
D TOUCH UP AS REQUIRED PER 235, 236 AND 242.
A CLEAN AND PREPARE EXPOSED INTERIOR SURFACES OF THE DOOR AND HINGE
PER 297.
B PAINT THE EXPOSED INTERIOR SURFACES WITH WHITE URETHANE COATING
PER 222.
C FINISH EXTERIOR SURFACE AFTER ASSEMBLY PER 16N0001.
D TOUCH UP AS REQUIRED PER 235, 237, AND 242.
A - 52

A633 WHITE ACRYLIC LACQUER/WHITE URETHANE. CLAD & 1000
3000,5000, & 6000 SERIES ALUM. ALLOYS(USE ONLY FOR
CLOSE MATING PARTS,DETAILS OF VALVE ASSEMBLIES)
A634 WHITE URETHANE FINISH & HARD ANODIZE
B ANODIZE REMAINING SURFACES PER 182.
D PAINT PRIMED SURFACES WITH WHITE URETHANE PER 222 (OR 274).
A635 DARK GRAY URETHANE AND 16NXXXX FINISH - PYLONS
C PAINT SPECIFIED INTERIOR SURFACES WITH DARK GRAY URETHANE COATING
PER 257 (OR 277).
A636 REWORK OF ANODIZED PYLONS & LAUNCHERS - DARK GRAY URETHANE AND
16NXXXX FINISH.
ALL ALUMINUM ALLOYS
A CLEAN AND BRUSH CHEM FILM EXPOSED SURFACES PER 134.
PER 257 (OR 277).
BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS.
C PAINT THE PRIMED INTERIOR SURFACES WITH EITHER WHITE ACRYLIC
LACQUER OR WHITE URETHANE COATING PER 294 (OR 296).
A - 53

(FOR CLOSE FIT TOLERANCES PART)
C PAINT PRIMED SURFACES WITH LUSTERLESS BLACK URETHANE PER 283 (OR 281).
A639 MEDIUM GRAY TEFLON URETHANE
(ADHESIVE BONDED ASSEMBLY)
A CLEAN AND BRUSH CHEM FILM ALL EXPOSED SURFACES PER 134.
C APPLY MEDIUM GRAY TEFLON URETHANE COATING PER 301.
PER 283 (OR 281).
D TOUCH UP AS REQUIRED PER 242 OR 285.
A641 LUSTERLESS RED LACQUER
CLAD AND 1000, 3000, 5000 AND 6000 SERIES ALUMINUM ALLOYS
C PAINT PRIMED SURFACES WITH LUSTERLESS RED LACQUER PER 303.
A642 MEDIUM GRAY TEFLON URETHANE
CLAD AND 1000, 3000, 5000 AND 6000 SERIES ALUMINUM ALLOYS AND
ALUMINUM CASTINGS
C APPLY MEDIUM GRAY TEFLON URETHANE COATING PER 301.
A643 REWORK OF ANODIZED PART - LUSTERLESS GRAY URETHANE
ALL ALUMINUM ALLOYS
C PAINT PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE PER 282 (OR 280).
A - 54

D PAINT PRIMED SURFACES WITH LUSTERLESS BLACK URETHANE PER 283 (OR 281).
A645 GRAY EPOXY ENAMEL/GRAY URETHANE AND HARD ANODIZE
ALL ALUMINUM ALLOYS
D PAINT PRIME SURFACES WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
ALL ALUMINUM ALLOYS
C APPLY SOLID FILM LUBE TO SPECIFIED SURFACES PER 207 IN
THICKNESSES OR DIMENSIONS AS NOTED.
FINISH. CLAD & 1000, 3000, 5000 AND 6000 SERIES
ALUM. ALLOYS & CASTINGS (FOR CLOSE TOLERANCE FITS)
C PRIME ONE COAT SPECIFIED EXTERIOR SURFACES PER 202.
D PAINT SPECIFIED INTERIOR SURFACES WITH EITHER WHITE ACRYLIC
F TOUCH UP AS REQUIRED PER 235, 242, OR 295.
E TOUCH-UP AS REQUIRED PER 235, 242 OR 295.
A - 55

A649 WHITE EPOXY ENAMEL/WHITE URETHANE AND BLACK
EPOXY ENAMEL/BLACK URETHANE. CLAD OR 1000, 3000,
5000 OR 6000 SERIES ALUMINUM ALLOYS
B PRIME SPECIFIED INTERIOR SURFACE ONE COAT PER 202.
C PRIME SPECIFIED EXPOSED SURFACE ONE COAT PER 202.
D PAINT SPECIFIED PRIMED EXPOSED SURFACE WITH WHITE EPOXY ENAMEL
OR WHITE URETHANE PER 233.
E PAINT SPECIFIED PRIMED EXPOSED SURFACE WITH BLACK EPOXY ENAMEL
OR BLACK URETHANE PER 213.
F TOUCH UP AS REQUIRED PER 239, 242, AND 357.
A650 PRIMER AND MEDIUM GRAY URETHANE
B PRIME TWO COATS ON SPECIFIED SURFACE PER 205 (OR 245).
D PAINT EXTERIOR EXPOSED SURFACE WITH MEDIUM GRAY URETHANE COATING
PER 290.
A651 WHITE ACRYLIC LACQUER/WHITE URETHANE AND P6194-1
COATING. CLAD OR 1000, 3000, 5000, OR 6000 SERIES
ALUMINUM ALLOYS AND CASTINGS
C SCUFF SAND SURFACE SPECIFIED TO BE COATED WITH P6194-1 PER 359.
D CLEAN SURFACE SPECIFIED TO BE COATED PER 358.
E APPLY P6194-1 COATING TO SPECIFIED AREAS PER 360.
F PAINT SPECIFIED SURFACE WITH EITHER WHITE ACRYLIC LACQUER OR
G TOUCH-UP AS REQUIRED PER 295.
A652 AMS-C-27725 FUEL TANK COATING AND SOLID FILM
LUBRICANT. CLAD OR 1000,3000,5000 OR 6000 ALUMINUM
ALLOYS (INCLUDING TUBING FOR DRAIN APPLICATIONS)
B APPLY SOLID FILM LUBE TO SPECIFIED SURFACES PER 207 IN
C APPLY AMS-C-27725 COATING ON SPECIFIED SURFACES PER 221.
D TOUCH-UP AS REQUIRED PER 240 AND 362.
A - 56

A653 GRAY EPOXY ENAMEL/GRAY URETHANE AND P6194-1 COATING
C SCUFF SAND PRIME TO BREAK SURFACE GLOSS ON SURFACES
SPECIFIED TO BE COATED WITH P6194-1 PER 359.
D CLEAN SPECIFIED SURFACE TO BE COATED PER 358.
E APPLY P6144-1 COATING (0.015" +/- .005" THICK) TO THE
SPECIFIED AREAS AND ALLOW TO CURE 24 HOURS PER 360.
F PAINT SPECIFIED SURFACE WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
G TOUCH-UP AS REQUIRED PER 238.
B PRIME ONE COAT SPECIFIED AREAS ON EXPOSED SURFACES PER 202.
D PAINT SPECIFIED AREAS ON EXPOSED SURFACES WITH GRAY EPOXY ENAMEL
E TOUCH-UP AS REQUIRED PER 236 AND 238.
A655 PRIMER AND 16NXXXX FINISH - SPECIAL BONDING APPLICATIONS.
D FINISH SPECIFIED EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING
16N0001.
E TOUCH-UP AS REQUIRED PER 242, 235, AND 236.
NOTE: FOR SPECIAL BONDING TO PRIMER; SEE MATERIALS AND PROCESSES
ENGINEERING FOR USE.
A656 PRIMER - SPECIAL BONDING APPLICATIONS
B PRIME TWO COATS ON SPECIFIED INTERIOR SURFACE PER 205 (OR 245).
D TOUCH-UP AS REQUIRED PER 235, 242, AND 236.
A - 57

A657 PRIMER AND AMS-C-27725 FUEL TANK COATING – SPECIAL BONDING
APPLICATIONS.
FUEL PER 221.
D TOUCH-UP AS REQUIRED PER 235 AND 240.
A658 AMS-C-27725 FUEL TANK COATING AND WHITE URETHANE –
SPECIAL BONDING APPLICATIONS.
FUEL PER 221.
C PRIME ONE COAT SURFACES EXPOSED IN WHEEL WELL, AMMUNITION OR GUN
BAY AREA PER 202.
D PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222 (OR 274).
A659 AMS-C-27725 FUEL TANK COATING AND LUSTERLESS GRAY
URETHANE - SPECIAL BONDING APPLICATIONS.
B APPLY AMS-C-27725 COATING TO SPECIFIED INTERIOR FAYING
SURFACES AND SURFACES EXPOSED TO FUEL PER 221.
C PRIME ONE COAT THE REMAINING SURFACES PER 202.
D PAINT THE INTERIOR NON-FUEL AREAS WITH LUSTERLESS GRAY
URETHANE COATING PER 282 (OR 280).
E TOUCH-UP AS REQUIRED PER 235, 240, 242 OR 284.
A - 58

PART OF CASTING COVERED BY INLET DUCT AND EXTERIOR SKINS.
B PRIME TWO COATS AREAS COVERED BY SKINS AS NOTED ON DRAWING
PER 205 (OR 245).
C PRIME ONE COAT THE EXPOSED INLET AND EXTERIOR SURFACES PER 202.
D PAINT SPECIFIED EXPOSED INLET SURFACES WITH LIGHT GRAY
URETHANE COATING PER 254 (OR 276) FOR FSD AIRCRAFT (61: NO.2
THRU NO. 6; 62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL
USE THE COLOR OF URETHANE COATING SPECIFIED ON APPLICABLE
E FINISH SPECIFIED EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING
16N0001.
F TOUCH-UP AS REQUIRED PER 235, 236, 242 AND 298.
A661 PRIMER, AMS-C-27725 FUEL TANK COATING AND WHITE
URETHANE - SPECIAL BONDING APPLICATIONS.
B PRIME TWO COATS SPECIFIED INTERIOR AREAS PER 205 (OR 245).
C PRIME ONE COAT SURFACES SPECIFIED FOR WHITE COLOR PER 202.
D PAINT SPECIFIED AREAS WITH WHITE URETHANE COATING PER 222 (OR 274).
E APPLY AMS-C-27725 COATING ON SPECIFIED FAYING SURFACES AND
SURFACES EXPOSED TO FUEL AREA PER 221.
G TOUCH-UP AS REQUIRED PER 235, 236, 237, 240 AND 242.
A662 PRIMER AND WHITE URETHANE - SPECIAL BONDING APPLICATIONS.
B PRIME TWO COATS SPECIFIED INTERIOR SURFACE PER 205 (OR 245).
E PRIME COATING EXPOSED EXTERIOR SURFACES ONE COAT PER 202.
F TOUCH-UP AS REQUIRED PER 235, 236, 237, AND 242.
A - 59

A663 WHITE ACRYLIC LACQUER OR WHITE URETHANE- SPECIAL
BONDING APPLICATIONS. BARE 2000AND 7000 SERIES ALUMINUM ALLOYS
D TOUCH UP AS REQUIRED PER 235,242, AND 295.
C PRIME OTHER SURFACES ONE COAT PER 202.
A665 PRIMER, AMS-C-27725 FUEL TANK COATING AND
16NXXXX FINISH - SPECIAL BONDING APPLICATIONS.
B APPLY AMS-C-27725 COATING ON SPECIFIED INTERIOR FAYING
C PRIME TWO COATS ON SPECIFIED INTERIOR SURFACES PER 205 (OR 245).
D PRIME ONE COAT ON REMAINING EXTERIOR SURFACES PER 202.
E PAINT SPECIFIED EXTERIOR SURFACES WITH DARK GRAY TEFLON-
THRU NO. 6, 62: NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL
ONTO FAYING SURFACES IS NOT PERMITTED.)
F FINISH SPECIFIED EXTERIOR SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
G TOUCH-UP AS REQUIRED PER 235, 236, 240, 242, AND 260 (FOR
THE GRAY COLOR ON FSD AIRCRAFT). TOUCH-UP AS REQUIRED
ON PRODUCTION AIRCRAFT PER 235, 236, 240, 242, AND 298.
D TOUCH-UP AS REQUIRED PER 242, 235, AND 236.
A - 60

A667 PRIMER, WHITE URETHANE, AND WHITE ACRYLIC LACQUER/
WHITE URETHANE - SPECIAL BONDING APPLICATIONS.
C PRIME ONE COAT REMAINING SURFACES PER 202.
D PAINT SURFACES SPECIFIED FOR WHITE URETHANE COATING PER 222 (OR 274).
E PAINT SPECIFIED SURFACES WITH WHITE ACRYLIC LACQUER OR
F TOUCH-UP AS REQUIRED PER 235, 236, 237, 242 AND 295.
FINISH - SPECIAL BONDING APPLICATIONS.
D FINISH SPECIFIED EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER
DRAWING 16N0001.
E TOUCH-UP AS REQUIRED PER 235, 242 OR 295.
A671 AMS-C-27725 FUEL TANK COATING AND WHITE
URETHANE - SPECIAL BONDING APPLICATION.
FUEL PER 221.
C PRIME ONE COAT ON EXPOSED SURFACES AND DESIGNATED EXTERIOR AREAS
PER 202.
D PAINT SPECIFIED PRIMED SURFACES WITH WHITE URETHANE COATING
PER 222 (OR 274).
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND CASTINGS
B PRIME ALL SURFACES WITH ONE COAT PER 201.
C PAINT SPECIFIED SURFACES WITH 36375 GRAY URETHANE PER 254.
A - 61

A673 PRIMER AND WHITE URETHANE - SPECIAL BONDING APPLICATIONS.
B APPLY SOLID FILM LUBRICANT TO SPECIFIED AREAS PER 207.
B PRIME INTERIOR SURFACES WITH TWO COATS PER 205 (OR 245).
C PRIME SPECIFIED EXTERIOR SURFACES WITH ONE COAT PER 202.
D PAINT SPECIFIED SURFACES THE COLOR OF URETHANE COATING
SPECIFIED ON THE APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
E TOUCH UP AS REQUIRED PER 235, 236, 242, AND 298.
A676 WHITE URETHANE, 16NXXXX FINISH (OVER SOLID FILM LUBRICANT),
AND HARD ANODIZE.
ALL ALUMINUM ALLOYS.
B APPLY SOLID FILM LUBRICANT TO ALL EXTERIOR SURFACES PER 207.
C PRIME REMAINING SURFACES WITH ONE COAT PER 202.
D PAINT INTERIOR SURFACES WITH WHITE URETHANE PER 222 (OR 274)
E PAINT ALL EXTERIOR SURFACES PER 16NXXXX.
F TOUCH UP AS REQUIRED PER 237, 242, 298, AND 362.
B PRIME TWO COATS ON SPECIFIED INTERIOR SURFACES PER 205 (OR 245).
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING
16NXXXX.
A - 62

CLAD OR 1000,3000,5000, OR 6000 SERIES ALUMINUM ALLOYS
B CHEM FILM REMAINING SURFACES PER 105.
A679 PRIMER AND 16NXXXX FINISH - SPECIAL BONDING
APPLICATIONS. CLAD OR 1000,3000,5000,OR 6000 SERIES ALUMINUM
ALLOYS AND CASTINGS
B APPLY TWO COATS OF PRIMER TO SPECIFIED SURFACES PER 205 (OR 245).
C APPLY ONE COAT OF PRIMER TO SPECIFIED SURFACE PER 202.
16NXXXX.
A680 LIGHT GRAY URETHANE
CLAD OR 1000, 3000, 5000, AND 6000 SERIES ALUMINUM ALLOYS OR CASTINGS
B PRIME SPECIFIED SURFACES WITH ONE COAT OF PRIMER PER 202.
C PAINT PRIMED SURFACES WITH LIGHT GRAY URETHANE PER 254.
CLAD OR 1000, 3000, 5000, AND 6000 SERIES ALUMINUM ALLOYS OR CASTINGS
B PRIME ALL SURFACES WITH ONE COAT OF PRIMER PER 201.
C PAINT PRIMED SURFACES WITH TWO COATS OF LIGHT GRAY URETHANE PER 253.
A - 63

A684 GRAY URETHANE AND 16NXXXX FINISH - PYLONS
PER 290 (OR 292).
A685 GRAY URETHANE AND 16NXXXX FINISH - PYLONS.
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND CASTINGS.
PER 290 (OR 292).
A686 FMS-3011 FORM II ADHESIVE PRIMER
B APPLY FMS-3011 FORM II ADHESIVE PRIMER TO ALL SURFACES PER 373.
C TOUCH UP PER 375.
A687 FMS-3011 FORM II ADHESIVE PRIMER
BARE 2000 AND 7000 SERIES ALUMIMUM ALLOYS
B APPLY FMS-3011 FORM II ADHESIVE PRIMER TO SPECIFIED SURFACES PER 374.
C TOUCH UP PER 375.
A CHEM FILM ALL SURFACES PER 105
PER 290 (OR 292)
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING 16N0005
A701 PRIMER, AMS-C-27725 FUEL TANK COATING AND 16NXXXX FINISH
B APPLY AMS-C-27725 COATING TO INTERIOR FAYING SURFACES AND
SURFACES EXPOSED TO FUEL AS NOTED ON THE DRAWING PER 221.
C PRIME TWO COATS ON REMAINING INTERIOR SURFACES PER 205 (OR 245).
F TOUCH UP AS REQUIRED PER 235, 236, 240 AND 242.
A - 64

A702 PRIMER AND 16NXXXX FINISH. BARE 2000 AND 7000
SERIES ALUMINUM ALLOY PART OF EXTERIOR SURFACE
COVERED BY FAIRING, NON-FUEL INTERIOR
B PRIME TWO COATS ON INTERIOR SURFACE AND ON EXTERIOR COVERED
SURFACE AS NOTED ON DRAWING PER 205 (OR 245).
C PRIME REMAINING EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
A703 PRIMER, AMS-C-27725 COATING, AND 16NXXXX
FINISH. BARE 2000 & 7000 SERIES ALUMINUM ALLOYS
WITH PART OF EXTERIOR SURFACE COVERED
C PRIME TWO COATS EXTERIOR COVERED SURFACE AS NOTED ON DRAWING
PER 205 (OR 245).
D PRIME REMAINING EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
A704 PRIMER, AMS-C-27725 COATING, AND 16NXXXX
FINISH. BARE 7000 SERIES & 2219 ALUMINUM ALLOYS
WITH PART OF EXTERIOR SURFACE COVERED
C PRIME TWO COATS ON EXTERIOR COVERED SURFACE AS NOTED ON DRAWING
PER 205 (OR 245).
D PRIME REMAINING EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
APPROVAL.
A - 65

PART OF CASTING COVERED BY INLET DUCT AND EXTERIOR SKINS
B PRIME TWO COATS AREAS COVERED BY SKINS AS NOTED ON DRAWING
PER 205 (OR 245).
C PRIME ONE COAT THE EXPOSED INLET AND EXTERIOR SURFACES PER 202.
D PAINT EXPOSED INLET SURFACES WITH LIGHT GRAY URETHANE COAT-
ING PER 254 (OR 276) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6,
COLOR OF URETHANE COATING SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT
PAINTING DRAWING.
F TOUCH UP AS REQUIRED PER 235, 236, 242 AND 255 (FOR THE
PRODUCTION AIRCRAFT PER 235, 236, 242 AND 298.
A706 PRIMER, AMS-C-27725 FUEL TANK COATING, WHITE
URETHANE,GRAY TEFLON-URETHANE, & 16NXXXX FINISH.
BARE 7000 SERIES & 2219 ALUMINUM ALLOYS
A SULFURIC ACID ANODIZE NOTED SURFACES PER 124.
B CHEM FILM TREAT SURFACES NOT ANODIZED PER 134.
C APPLY AMS-C-27725 COATING TO INTERIOR FAYING SURFACES AND
D PRIME TWO COATS ON EXTERIOR COVERED SURFACES AS NOTED ON DRAWING
PER 205 (OR 245).
E APPLY DARK GRAY TEFLON-URETHANE COATING ON THE SPECIFIED PRIMED
AREA PER 259.
F ON EXTERIOR SURFACES EXPOSED IN COVE AREAS PRIME ONE COAT PER 202.
G ON EXTERIOR SURFACES EXPOSED IN COVE AREAS APPLY WHITE
H FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
I TOUCH UP AS REQUIRED PER 235, 236, 237, 240 & 260.
J (SEE A739 FOR PREFERRED CODE).
APPROVAL.
A - 66

A707 PRIMER, AMS-C-27725 FUEL TANK COATING, WHITE URETHANE,
AND 16NXXXX FINISH.
B "DELETED"
D PRIME TWO COATS ON EXTERIOR COVERED SURFACES SPECIFIED
PER 205 (OR 245).
E APPLY DARK GRAY TEFLON-URETHANE COATING ON THE SPECIFIED
PRIMED AREA PER 259 (OR 288) FOR FSD AIRCRAFT (61: NO. 2
F ON EXTERIOR SURFACES EXPOSED IN COVE AREAS AND EXTERIOR
NON-COVERED SURFACES PRIME ONE COAT PER 202.
G ON EXTERIOR SURFACES EXPOSED IN COVE AREA APPLY WHITE
H FINISH EXTERIOR EXPOSED SURFACE AFTER ASSY PER DRAWING 16N0001.
I TOUCH UP AS REQUIRED FOR THE GRAY COLOR ON FSD AIRCRAFT
PER BASIC ELEMENTS 235, 236, 237 (CONT'D IN NEXT STEP)
J (CONT'D FROM PREVIOUS STEP) AND PER 240, 242, AND 260.
K TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 235, 236, 237 AND
(CONT ON NEXT STEP)
L (CONT'D FROM PREVIOUS STEP) TOUCH UP PER 240, 242, & 298.
A708 PRIMER, AMS-C-27725 FUEL TANK COATING, AND WHITE URETHANE
C PRIME TWO COATS ON SPECIFIED INTERIOR NON-FUEL AND NON-WHITE
SURFACES PER 205 (OR 245).
D PRIME ONE COAT ON SPECIFIED SURFACES REQUIRING WHITE COLOR PER 202.
E PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
FUEL PER 221.
C PRIME ONE COAT SURFACES EXPOSED IN WHEEL WELL, AMMUNITION OR GUN
BAY AREA PER 202.
A - 67

A711 AMS-C-27725 FUEL TANK COATING, WHITE URETHANE, AND 16NXXXX FINISH
SURFACE EXPOSED TO FUEL PER 221.
C PRIME ONE COAT REMAINING INTERIOR SURFACES PER 202.
F FINISH EXTERIOR SURFACES AFTER ASSY PER DRAWING 16N0001.
G TOUCH UP AS REQUIRED PER 237, 240, AND 242.
C PAINT INTERIOR SURFACE WITH WHITE URETHANE COATING PER 222 (OR 274).
D FINISH EXTERIOR EXPOSED SURFACES WITH DARK GRAY TEFLON-
PER 236 AND 298.
A713 WHITE URETHANE, 16NXXXX FINISH, SOLID FILM
LUBRICANT, AND HARD ANODIZE.
A PREPARE SURFACES PER FPS-3006 CLASS X.
B HARD ANODIZE SPECIFIED SURFACES PER 115.
C APPLY SOLID FILM LUBE TO HARD ANODIZE SURFACES PER 207.
D BRUSH CHEM FILM AREAS NOT HARD ANODIZED PER 134.
E PRIME ONE COAT INTERIOR SURFACES PER 202.
F PAINT PRIMED INTERIOR SURFACES WITH WHITE URETHANE COATING
PER 222 (OR 274).
G PRIME REMAINING EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
H FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER DRAWING 16N0001.
I TOUCH UP AS REQUIRED PER 235, 237, 242, AND 362.
A715 BLACK EPOXY ENAMEL/BLACK URETHANE AND 16NXXXX FINISH
ALUMINUM CASTINGS
B PRIME TWO COATS ALL SURFACES PER 204 (OR 245).
C PAINT INTERIOR SPECIFIED SURFACES WITH BLACK EPOXY ENAMEL OR
D EXTERIOR SURFACE (PRIMED IN B) WILL BE FINISHED AFTER ASSEMBLY PER
16N0001.
A - 68

A716 PRIMER, AMS-C-27725 FUEL TANK COATING,
WHITE URETHANE, AND 16NXXXX FINISH
B PRIME TWO COATS SPECIFIED INTERIOR AREAS PER 205 (OR 245).
D PAINT SPECIFIED AREAS WITH WHITE URETHANE COATING PER 222 (OR 274).
G FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
H TOUCH UP AS REQUIRED PER 235, 236, 237, 240, AND 242.
A717 PRIMER, WHITE URETHANE, AND 16NXXXX FINISH
B PRIME TWO COATS SPECIFIED INTERIOR SURFACE PER 205 (OR 245).
F FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
G TOUCH UP AS REQUIRED PER 235, 236, 237 AND 242.
A720 PRIMER AND DARK GRAY URETHANE
B PRIME TWO COATS ON SPECIFIED SURFACES PER 205 (OR 245).
C PRIME ONE COAT ON SURFACES SPECIFIED FOR DARK GRAY COLOR PER 202.
D PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE COATING
PER 257 (OR 277).
C PAINT ALL SURFACES WITH DARK GRAY URETHANE COATING PER 263 (OR 277).
C PRIME ONE COAT ON SURFACES SPECIFIED FOR DARK GRAY COLOR PER 202.
PER 257 (OR 277).
A - 69

CLAD, OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND
C PAINT ALL SURFACES WITH DARK GRAY URETHANE COATING PER 263 (OR 277).
AND 16NXXXX FINISH
B PRIME TWO COATS SPECIFIED INTERIOR AREA PER 205 (OR 245).
C PRIME ONE COAT ON SURFACES REQUIRING EITHER WHITE COLOR OR 16N0001
FINISH PER 202.
D PAINT SPECIFIED AREA WITH WHITE URETHANE COATING PER 222 (OR 274).
G TOUCH UP AS REQUIRED PER 235, 236, 237, AND 240.
H (SEE A716 FOR PREFERRED CODE).
APPROVAL.
A725 AMS-C-27725 FUEL TANK COATING, BLACK EPOXY ENAMEL/
BLACK URETHANE, AND 16NXXXX FINISH
C PRIME ONE COAT ON SURFACES SPECIFIED FOR BLACK COLOR PER 202
PER 213.
F FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER DRAWING 16N0001.
A726 PRIMER, DARK GRAY URETHANE, AND HARD ANODIZE
C PRIME TWO COATS TO SURFACES SPECIFIED FOR PRIME ONLY PER 205 (OR 245).
D PRIME ONE COAT TO SURFACES SPECIFIED FOR GRAY COLOR PER 202.
E PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE COATING
PER 257 (OR 277).
A - 70

A727 PRIMER , WHITE URETHANE, AND 16NXXXX FINISH
PAINTING DRAWING.
G TOUCH UP AS REQUIRED PER 235, 236, 237, 242, AND 258 FOR
FSD AIRCRAFT. TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 235, 236,
237, 242, AND 298.
A729 WHITE URETHANE, 16NXXXX FINISH, AND HARD ANODIZE
ALL ALUMINUM ALLOYS
B CHEM FILM SURFACES NOT ANODIZED PER 134.
C PRIME AREAS SPECIFIED FOR WHITE COLOR ONE COAT PER 202.
D PAINT SPECIFIED AREAS WITH WHITE URETHANE PER 222 (OR 274).
E PRIME CHEM FILMED EXTERIOR EXPOSED SURFACES ONE COAT PER 202
F FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER DRAWING 16N0001.
A730 PRIMER, DARK GRAY URETHANE, & SOLID FILM LUBRICANT
BARE 7000 AND 2219 ALUMINUM ALLOYS
B APPLY SOLID FILM LUBE TO SURFACES SPECIFIED PER 207.
C PRIME 2 COATS ON SPECIFIED SURFACES PER 205 (OR 245).
D PRIME 1 COAT SURFACE SPECIFIED FOR GRAY URETHANE PER 202.
E PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE PER 257.
APPROVAL.
A - 71

B PRIME TWO COATS SPECIFIED INTERIOR SURFACES PER 205 (OR 245)
D PAINT SPECIFIED SURFACES WITH DARK GRAY TEFLON-URETHANE
THE COLOR OF TEFLON-URETHANE COATING SPECIFIED ON APPLICABLE
F TOUCH UP AS REQUIRED PER 235, 236, 242, AND 260 (FOR THE
PRODUCTION AICRAFT PER 235, 236, 242, AND 298.
A732 PRIMER,DARK GRAY TEFLON-URETHANE, & 16NXXXX FINISH
C PRIME ONE COAT ON SURFACES REQUIRING EITHER TEFLON-
URETHANE COATING OR 16N0001 FINISH PER 202.
D PAINT SPECIFIED SURFACES WITH DARK GRAY TEFLON-URETHANE COATING
PER 259.
APPROVAL.
A734 PRIMER, AMS-C-27725 FUEL TANK COATING, AND 16NXXXX FINISH
B APPLY AMS-C-27725 COATING ON SPECIFIED INTERIOR FAYING
C PRIME TWO COATS ON SPECIFIED INTERIOR SURFACES PER 205 (OR 245).
D PRIME ONE COAT ON REMAINING EXTERIOR SURFACES PER 202.
E PAINT SPECIFIED EXTERIOR SURFACES WITH DARK GRAY TEFLON-
ONTO FAYING SURFACES IS NOT PERMITTED.)
F FINISH REMAINING EXTERIOR SURFACES AFTER ASSEMBLY PER DRAWING
16N0001.
G TOUCH UP AS REQUIRED PER 235, 236, 240, 242 AND 260 (FOR
THE GRAY COLOR ON FSD AIRCRAFT). TOUCH UP AS REQUIRED
ON PRODUCTION AIRCRAFT PER 235, 236, 240, 242, AND 298.
A - 72

A735 AMS-C-27725 FUEL TANK COATING, LIGHT GRAY URETHANE
AND 16NXXXX FINISH
C PRIME ONE COAT ON SURFACES REQUIRING EITHER LIGHT GRAY
D PAINT SPECIFIED SURFACES WITH LIGHT GRAY URETHANE COATING PER 254.
APPROVAL.
A736 AMS-C-27725 FUEL TANK COATING, WHITE URETHANE, AND
BLACK EPOXY ENAMEL/BLACK URETHANE
B APPLY AMS-C-27725 COATING TO SPECIFIED FAYING SURFACES AND
C PRIME ONE COAT SURFACES SPECIFIED REQUIRING BLACK PER 202.
D PAINT SPECIFIED AREAS WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
E PRIME ONE COAT SURFACES SPECIFIED REQUIRING WHITE PER 202.
F PAINT SPECIFIED AREAS WITH WHITE URETHANE PER 222 (OR 274).
AND BLACK EPOXY ENAMEL/BLACK URETHANE
B APPLY AMS-C-27725 COATING TO SPECIFIED FAYING SURFACES AND
C PRIME TWO COATS SPECIFIED INTERIOR SURFACES PER 205 (OR 245)
D PRIME ONE COAT SURFACES REQUIRING BLACK EPOXY PER 202.
E PAINT SPECIFIED SURFACES WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
A - 73

AND 16NXXXX FINISH
A SULFURIC ACID ANODIZE SURFACES NOTED PER 124.
C PRIME TWO COATS SPECIFIED INTERIOR AREA PER 205 (OR 245).
D PRIME ONE COAT ON SURFACES REQUIRING EITHER WHITE
E PAINT SPECIFIED AREA WITH WHITE URETHANE COATING PER 222 (OR 274).
F APPLY AMS-C-27725 COATING ON SPECIFIED FAYING SURFACES AND
G FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
H TOUCH UP AS REQUIRED PER 235, 236, 237, AND 240.
I (SEE A716 FOR PREFERRED CODE).
APPROVAL.
A739 PRIMER, AMS-C-27725 FUEL TANK COATING, WHITE
URETHANE, AND 16NXXXX FINISH. BARE 2000 OR
7000 SERIES AL ALLOYS USED FOR LOWER WING SKINS
A ANODIZE NOTED SURFACES PER 114.
D PRIME TWO COATS ON EXTERIOR COVERED SURFACES AS NOTED ON DRAWING
PER 205 (OR 245).
E APPLY DARK GRAY TEFLON-URETHANE COATING ON THE SPECIFIED
PRIMED AREA PER 259 (OR 288) FOR FSD AIRCRAFT (61: NO. 2
F ON EXTERIOR SURFACES EXPOSED IN COVE AREAS AND EXTERIOR
NON-COVERED SURFACES PRIME ONE COAT PER 202.
G ON EXTERIOR SURFACES EXPOSED IN COVE AREAS APPLY WHITE
H FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
I TOUCH UP AS REQUIRED FOR THE GRAY COLOR ON THE FSD AIRCRAFT
PER 235, 236, 237 AND (CONTINUED IN NEXT STEP)
J (CONT'D FROM PREVIOUS STEP) TOUCH UP PER 240, 242, AND 260.
K TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 235,
236, 237, AND (CONTINUED IN FOLLOWING STEP)
L (CONTINUED FROM PREVIOUS STEP) TOUCH UP PER 240, 242,& 298.
A - 74

A740 PRIMER, 16NXXXX FINISH, AND SOLID FILM LUBRICANT
C PRIME TWO COATS ON SPECIFIED SURFACES PER 205 (OR 245).
D PRIME ONE COAT REMAINING SURFACES PER 202.
E PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE PER 275
(OR 277) FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, 62: NO.1
AND NO. 2). PRODUCTION AIRCRAFT SHALL USE THE COLOR OF
PAINTING DRAWING.
F TOUCH UP AS REQUIRED PER 236 AND 238 (FOR THE GRAY COLOR ON
PER 236 AND 298.
C PRIME ONE COAT REMAINING SPECIFIED SURFACES PER 202.
D PAINT SPECIFIED SURFACES WITH LIGHT GRAY URETHANE COATING
NO. 1 AND NO. 2). PRODUCTION AIRCRAFT SHALL BE OF THE COLOR
PAINTING DRAWING.
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER 16N0001.
PRODUCTION AIRCRAFT PER 235, 240, 242, AND 298.
PAINTING DRAWING.
F TOUCH UP AS REQUIRED PER 235, 236, 242 AND 252 (FOR THE GRAY
AIRCRAFT PER 235, 236, 242 AND 298.
A - 75

A743 PRIMER, LIGHT GRAY URETHANE, AND DARK GRAY TEFLON - URETHANE
BARE 7000 SERIES ALUMINUM ALLOYS
C PRIME ONE COAT SURFACES SPECIFIED FOR LIGHT GRAY COLOR AND
FOR DARK GRAY TEFLON-URETHANE PER 202.
PER 254 (OR 276).
E PAINT SPECIFIED SURFACES WITH DARK GRAY TEFLON-URETHANE
COATING PER 259 (OR 288). (OVERSPRAY NOT PERMITTED ON FAYING SURFACES).
NOTE: DO NOT USE THIS CODE WITHOUT MATERIALS & PROCESSES ENGINEERING
APPROVAL.
COLOR OF URETHANE COATING SPECIFIED ON THE APPLICABLE
E PAINT SPECIFIED SURFACES WITH DARK GRAY TEFLON-URETHANE
COATING PER 259 (AND 288) FOR FSD AIRCRAFT (61: NO. 2 THRU
THE COLOR OF THE TEFLON-URETHANE COATING SPECIFIED ON THE
NOT PERMITTED ON FAYING SURFACES.)
F TOUCH UP AS REQUIRED PER 236 AND PER 255 AND 260 (FOR THE
PRODUCTION AIRCRAFT PER 236 AND 298.
A745 PRIMER AND 16NXXXX FINISH - CLAD 1000, 3000, 5000, AND 6000 SERIES
ALUMINUM ALLOYS AND ALUMINUM CASTING
PER 254 (OR 276) AND PAINT SPECIFIED SURFACES WITH DARK GRAY
URETHANE COATINGS PER 257 (OR 277) FOR FSD AIRCRAFT
(61: NO. 2 THRU NO. 6, 62: NO. 1 AND NO. 2). PRODUCTION
AIRCRAFT SHALL USE THE COLORS OF URETHANE COATINGS SPECIFIED
ON THE APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
D TOUCH UP AS REQUIRED PER 242 AND PER 255 AND 258 (FOR THE
GRAY COLORS ON FSD AIRCRAFT). TOUCH UP AS REQUIRED ON
PRODUCTION AIRCRAFT PER 242 AND 298.
A - 76

A746 16NXXXX FINISH
C APPLY DARK GRAY URETHANE COATING TO SPECIFIED SURFACES
D FINISH SPECIFIED EXTERIOR SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
E TOUCH UP AS REQUIRED PER 235, 242, AND 258 (FOR THE GRAY
AIRCRAFT PER 235, 242, AND 298.
ALL ALUMINUM ALLOY CASTINGS
B PRIME SURFACES SPECIFIED FOR PRIME TWO COATS PER 205 (OR 245).
D PAINT SPECIFIED EXTERIOR SURFACES WITH LIGHT GRAY TEFLON-
USE THE COLOR OF TEFLON-URETHANE COATING SPECIFIED ON THE
E FINISH REMAINING EXTERIOR SURFACES AFTER ASSY PER 16N0001.
PRODUCTION AIRCRAFT PER 235, 236, 242, AND 298.
A748 AMS-C-27725 FUEL TANK COATING, LUSTERLESS GRAY URETHANE,
AND 16NXXXX FINISH
D PAINT THE INTERIOR NON-FUEL AREAS WITH LUSTERLESS GRAY
A - 77

LUSTERLESS GRAY URETHANE
E PAINT INTERIOR NON-FUEL AND NON-WHITE SURFACES WITH LUSTERLESS
GRAY URETHANE PER 282 (OR 280).
A750 WHITE URETHANE, LUSTERLESS GRAY URETHANE, AND 16NXXXX FINISH
C PAINT SPECIFIED INTERIOR SURFACES WITH WHITE URETHANE COATING
PER 222 (OR 274).
D PAINT NON-WHITE INTERIOR SURFACES WITH LUSTERLESS GRAY
URETHANE PER 282 (OR 280).
F TOUCH UP AS REQUIRED PER 235, 237, 242, OR 284.
A751 AMS-C-27725 FUEL TANK COATING, LUSTERLESS BLACK URETHANE,
AND 16NXXXX FINISH
C PRIME ONE COAT ON ALL NON-FUEL SURFACES PER 202.
D PAINT INTERIOR NON-FUEL AREAS WITH LUSTERLESS BLACK URETHANE
PER 283 (OR 281).
A752 WHITE URETHANE, LUSTERLESS GRAY URETHANE, AND
16NXXXX FINISH. CLAD AND 1000, 3000, 5000 & 6000
SERIES ALUMINUM ALLOYS AND ALUMINUM CASTINGS
C PAINT SPECIFIED PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE
PER 282 (OR 280).
D PAINT SPECIFIED PRIMED SURFACES WITH WHITE URETHANE PER 222 (OR 274).
A - 78

A753 PRIMER, LUSTERLESS GRAY URETHANE, AND 16NXXXX FINISH
B PRIME SURFACES SPECIFIED FOR PRIME TWO COATS PER 205.
B PRIME SURFACES SPECIFIED FOR PRIME TWO COATS PER 205.
A755 WHITE URETHANE, LUSTERLESS GRAY URETHANE, AND LUSTERLESS
BLACK URETHANE
PER 283 (OR 281).
PER 282 (OR 280).
A756 WHITE ACRYLIC LACQUER/WHITE URETHANE, LUSTERLESS
GRAY URETHANE, & 16NXXXX FINISH. CLAD,1000,3000
5000 & 6000 SERIES ALUM. ALLOYS & ALUM. CASTINGS
C PAINT SPECIFIED PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE
PER 282 (OR 280).
D PAINT SPECIFIED PRIMED SURFACES WITH EITHER WHITE ACRYLIC
A - 79

AND WHITE ACRYLIC LACQUER/WHITE URETHANE
C PRIME TWO COATS ON SPECIFIED INTERIOR NON-FUEL AND NON-WHITE
SURFACES PER 205 (OR 245).
D PRIME ONE COAT ON SPECIFIED SURFACES REQUIRING WHITE COLOR PER 202.
E PAINT SPECIFIED SURFACES WITH EITHER WHITE ACRYLIC LACQUER
A758 PRIMER, WHITE ACRYLIC LACQUER/WHITE URETHANE, AND 16NXXXX FINISH
B PRIME TWO COATS SPECIFIED INTERIOR SURFACES PER 205 (OR 245)
GRAY URETHANE, AND 16NXXXX FINISH
C PAINT SPECIFIED INTERIOR SURFACES WITH EITHER WHITE ACRYLIC
LACQUER OR WHITE URETHANE COATING PER 294 (OR 296)
F TOUCH UP AS REQUIRED PER 235, 242, 284 AND 295.
A760 AMS-C-27725 FUEL TANK COATING, WHITE ACRYLIC
LACQUER/WHITE URETHANE, AND 16NXXXX FINISH
C PRIME ONE COAT REMAINING INTERIOR SURFACES PER 202.
E PRIME ONE COAT EXTERIOR EXPOSED SURFACES PER 202.
A - 80

A761 PRIMER, WHITE ACRYLIC LACQUER/WHITE URETHANE,
AND LUSTERLESS GRAY URETHANE
B PRIME TWO COATS SURFACES SPECIFIED FOR PRIME PER 205 (OR 245).
C PRIME THE REMAINING SURFACES PER 202.
GRAY URETHANE, AND LUSTERLESS BLACK URETHANE
PER 283 (OR 281).
PER 282 (OR 280).
D PAINT SPECIFIED SURFACES WITH LIGHT GRAY TEFLON URETHANE
THE COLOR OF TEFLON URETHANE COATING SPECIFIED ON THE
F FINISH REMAINING EXTERIOR SURFACES AFTER ASSEMBLY PER 16N0001.
G TOUCH UP AS REQUIRED PER 235, 236, 237, 242, AND 262 (FOR
THE GRAY COLOR ON FSD AIRCRAFT). TOUCH UP ON PRODUCTION
AIRCRAFT PER 235, 236, 237, 242, AND 298.
A - 81

D PAINT SPECIFIED SURFACES WITH LIGHT GRAY TEFLON-URETHANE
THE COLOR OF TEFLON-URETHANE COATING SPECIFIED ON THE
F TOUCH UP AS REQUIRED PER 236, 237, AND 262 (FOR THE GRAY
COLOR ON FSD AIRCRAFT). TOUCH UP ON PRODUCTION AIRCRAFT PER 236, 237,
AND 298.
BLACK URETHANE, AND 16NXXXX FINISH
BARE 2000 OR 7000 SERIES ALUMINUM ALLOYS
C PAINT SPECIFIED INTERIOR SURFACES WITH EITHER WHITE ACRYLIC
D PAINT SPECIFIED SURFACES WITH LUSTERLESS BLACK URETHANE COATING
PER 283 (OR 281).
F TOUCH UP AS REQUIRED PER 235, 237 ,242, 285, AND 295.
A766 WHITE URETHANE, WHITE ACRYLIC LACQUER/WHITE
URETHANE, AND LUSTERLESS GRAY URETHANE
C PAINT SPECIFIED SURFACES WITH LUSTERLESS GRAY URETHANE COATING
PER 282 (OR 280).
E PAINT THE REMAINING SURFACES WITH EITHER WHITE ACRYLIC
A767 PRIMER, WHITE URETHANE, AND WHITE ACRYLIC LACQUER/WHITE
URETHANE
B PRIME ONE COAT SURFACES SPECIFIED FOR WHITE COLOR PER 202.
C PRIME TWO COATS SURFACES SPECIFIED FOR "PRIME" PER 205 (OR 245).
A - 82

A768 AMS-C-27725 COATING, WHITE URETHANE, WHITE
ACRYLIC LACQUER/WHITE URETHANE & LUSTERLESS GRAY
URETHANE. BARE 2000 OR 7000 SERIES ALLOYS
PER 282 (OR 280).
F PAINT SPECIFIED SURFACES WITH EITHER WHITE ACRYLIC LACQUER
A769 PRIMER, WHITE ACRYLIC LACQUER/WHITE URETHANE, AND 16NXXXX FINISH.
WHITE ACRYLIC LACQUER/WHITE URETHANE
E PAINT REMAINING SURFACES WITH EITHER WHITE ACRYLIC LACQUER
A771 PRIMER, DARK GRAY URETHANE, AND 16NXXXX FINISH
ALUMINUM ALLOY CASTINGS - PYLON
B PRIME TWO COATS SPECIFIED INTERIOR SURFACES PER 205 (OR 245).
D PAINT SPECIFIED INTERIOR SURFACES WITH DARK GRAY URETHANE COATING
PER 257 (OR 277).
E FINISH EXTERIOR SURFACES AFTER ASSEMBLY PER DRAWING 16N0005.
F TOUCH UP AS REQUIRED PER 236, 242, 246 OR 258.
A - 83

A772 PRIMER, 16NXXXX FINISH, AND SOLID FILM LUBRICANT - PYLONS.
B APPLY SOLID FILM LUBE TO SPECIFIED SURFACES IN THICKNESS OR
DIMENSIONS AS NOTED PER 207.
C PRIME TWO COATS SPECIFIED INTERIOR SURFACES PER 205 (OR 245)
E FINISH EXTERIOR PRIMED SURFACES AFTER ASSEMBLY PER DRAWING 16N0005.
D PAINT SPECIFIED INTERIOR SURFACES WITH DARK GRAY URETHANE COATING
PER 257 (OR 277).
A774 PRIMER, DARK GRAY URETHANE, 16NXXXX FINISH, HARD
ANODIZE - PYLONS. 2000 AND 7000 SERIES ALUMINUM ALLOYS.
C PRIME TWO COATS SPECIFIED SURFACES PER 205 (OR 245).
D PRIME ONE COAT REMAINING SPECIFIED SURFACES PER 202.
E PAINT SPECIFIED INTERIOR SURFACES WITH DARK GRAY URETHANE COATING
PER 257 (OR 277).
G TOUCH UP AS REQUIRED PER 236, 242, 246, OR 258.
A775 PRIMER, WHITE URETHANE, WHITE ACRYLIC
D PAINT SURFACES SPECIFIED FOR WHITE URETHANE COATING PER 222 (OR 274).
G TOUCH UP AS REQUIRED PER 235, 236, 237, 242, OR 295.
A - 84

A776 PRIMER, LUSTERLESS GRAY URETHANE, AND 16NXXXX FINISH
PER 282 (OR 280).
A777 PRIMER, 16NXXXX FINISH, AND CHROMIUM PLATE
(DO NOT USE WITHOUT M&P ENGINEERING APPROVAL)
A CHROME PLATE SPECIFIED SURFACES PER 186.
B BRUSH CHEM FILM REMAINING SURFACES PER 134.
C PRIME TWO COATS SPECIFIED SURFACES PER 205.
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER APPLICABLE
F TOUCH-UP AS REQUIRED PER 235, 236, 242, OR 298.
A778 WHITE URETHANE AND SOLID FILM LUBRICANT
B APPLY SOLID FILM LUBE TO SPECIFIED SURFACES PER 207 IN
E TOUCH-UP AS REQUIRED PER 242 OR 237.
A779 PRIMER, WHITE URETHANE, AND LUSTERLESS GRAY URETHANE
F TOUCH-UP AS REQUIRED PER 236, 237, 242, OR 284.
A780 PRIMER, DARK GRAY URETHANE, AND SOLID FILM LUBRICANT
C PRIME TWO COATS ON SPECIFIED SURFACES PER 205 (OR 245).
D PRIME ONE COAT ON SURFACES SPECIFIED FOR DARK GRAY COLOR PER 202.
PER 257 (OR 277).
A - 85

C PAINT ONE COAT ALL SURFACES WITH GRAY EPOXY ENAMEL OR GRAY
URETHANE PER 227.
B PRIME TWO COATS ON INTERIOR SURFACE PER 205.
C PRIME ONE COAT ON EXTERIOR SURFACE PER 202.
D PAINT SPECIFIED INTERIOR SURFACES WITH WHITE URETHANE PER 222 (OR 274).
A784 PRIMER, WHITE ACRYLIC LACQUER/WHITE URETHANE,
LUSTERLESS GRAY URETHANE & 16NXXXX FINISH. CLAD
OR 1000,3000,5000,6000 ALUM. ALLOYS & CASTINGS.
B PRIME TWO COATS ON SPECIFIED SURFACES PER 205.
D PAINT SURFACES SPECIFIED FOR GRAY WITH LUSTERLESS GRAY URETHANE
PER 282 (OR 280).
E PAINT SURFACES SPECIFIED FOR WHITE COLOR WITH EITHER WHITE
ACRYLIC LACQUER OR WHITE URETHANE COATING PER 294 (OR 296).
A785 AMS-C-27725 FUEL TANK COATING AND GRAY URETHANE
B APPLY AMS-C-27725 COATING ON SPECIFIED FAYING SURFACE AND
C PRIME ONE COAT EXTERIOR SURFACES REQUIRING GRAY COLOR PER 202.
D PAINT SPECIFIED EXTERIOR SURFACES WITH GRAY COLOR 36270 URETHANE
COATING PER 290.
A - 86

B PRIME TWO COATS ALL SURFACES PER 204.
A787 PRIMER & LUSTERLESS BLACK URETHANE
PER 283 (OR 281).
D PRIME REMAINING SURFACES TWO COATS, PER 205.
A788 PRIMER & LUSTERLESS BLACK URETHANE
PER 283 (OR 281).
D PRIME REMAINING SURFACES TWO COATS, PER 205.
A NOTE: THIS CODE IS INACTIVE.
THIS CODE IS A DUPLICATE OF A559; USE A559 FOR NEW DESIGNS.
B ANODIZE ALL SURFACES PER 111.
E TOUCH UP AS REQUIRED PER 241
A790 PRIMER, 16NXXXX FINISH, AND HARD ANODIZE
2000 OR 7000 SERIES ALLOYS
B PRIME TWO COATS SPECIFIED SURFACES PER 205.
C PRIME ONE COAT REMAINING SURFACES PER 202. (TWO COATS PER 205 IS
OPTIONAL.)
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER APPLICABLE
E TOUCH UP AS REQUIRED PER 235, 236, 242, OR 298.
A - 87

A791 MEDIUM GRAY TEFLON-URETHANE AND 16NXXXX FINISH
BARE 2000 OR 7000 SERIES ALLOYS
A ANODIZE PER 111.
C PAINT SPECIFIC SURFACES WITH 2 COATS TEFLON URETHANE, MEDIUM GRAY
COLOR, PER 301.
D FINISH EXTERIOR SURFACES AFTER ASSY PER DRAWING 16N0001.
E TOUCH UP PER 235, 236, 242, OR 302.
A792 WHITE TEFLON-URETHANE
CLAD AND 1000, 3000, 5000, AND 6000 SERIES
ALUMINUM ALLOYS AND ALUMINUM CASTINGS
C APPLY WHITE TEFLON URETHANE COATING PER 352.
A793 DARK GRAY URETHANE. AL ALLOY CASTINGS & CLAD OR
1000, 3000, 5000 OR 6000 SERIES ALUM. ALLOYS AND
ELECTRICAL BONDING ON 2000 & 7000 SERIES ALUM.
PER 263 (OR 277).
A794 PRIMER AND MEDIUM GRAY TEFLON-URETHANE.
CLAD OR 1000, 3000, 5000, 6000 SERIES
ALUMINUM ALLOYS AND ALUMINUM CASTINGS.
C APPLY MEDIUM GRAY TEFLON URETHANE ON SPECIFIED SURFACES PER 354.
A795 PRIMER, DARK GRAY URETHANE, AND 16NXXXX FINISH.
REWORK OF PREVIOUSLY ANODIZED PYLON PARTS.
A CLEAN AND BRUSH CHEM FILM EXPOSED SURFACES PER 134.
PER 257 (OR 277).
A - 88

A797 CHEMICAL FILM
ALL ALUMINUM ALLOYS
B TOUCH UP AS REQUIRED PER 354.
C (INACTIVE FOR NEW DESIGN).
B PRIME 2 COATS ALL SURFACES PER 204.
D FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER 16N0001.
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND
ALUMINUM CASTINGS
B APPLY SOLID FILM LUBRICANT TO ALL SURFACES PER 228.
A800 FMS-3014 FORM 2 ADHESIVE PRIMER
B APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO ALL SURFACES PER 400.
C TOUCH UP AS REQUIRED PER 401 (OR 402 AS APPLICABLE).
A801 FMS-3014 FORM 2 ADHESIVE PRIMER AND WHITE URETHANE
C PAINT SPECIFIED SURFACES WITH URETHANE COATING;
WHITE COLOR NUMBER 17875 OR WHITE COLOR NUMBER 17925 PER 406
D TOUCH UP AS REQUIRED PER 237, 401 (OR 402 AS APPLICABLE), AND 404.
NOTE: A802 IS DUPLICATE CODE OF A800. DO NOT USE A802 FOR NEW DESIGN.
A803 FMS-3014 FORM 2 ADHESIVE PRIMER AND 16NXXXX FINISH
B APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO SPECIFIED SURFACES
AND SURFACES EXPOSED TO FUEL PER 403.
C PRIME EXTERIOR EXPOSED SURFACES WITH ONE COAT OF PRIMER PER 202.
16NXXXX.
E TOUCH UP AS REQUIRED PER 235 AND 401 (OR 402 AS APPLICABLE).
A - 89

A804 PRIMER, FMS-3014 FORM 2 ADHESIVE PRIMER,
AND 16NXXXX FINISH. BARE 2000 & 7000 SERIES
ALLOYS (WITH PART OF EXTERIOR SURFACE COVERED).
B APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO SPECIFIED INTERIOR
C PRIME EXTERIOR COVERED SURFACE (AS NOTED ON DRAWING) WITH
TWO COATS OF PRIMER PER 205 (OR 245).
D PRIME REMAINING EXTERIOR EXPOSED SURFACES WITH ONE COAT OF PRIMER
PER 202.
E FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16NXXXX.
F TOUCH UP AS REQUIRED PER 235,236,242,& 401 (OR 402 AS APPLICABLE.
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM
ALLOYS AND ALUMINUM CASTINGS (EXCEPT TUBING)
A807 FMS-3014 FORM 2 ADHESIVE PRIMER, WHITE URETHANE, AND 16NXXXX FINISH
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE; COLOR NO.17875
OR COLOR NO. 17925 PER 406.
D PRIME EXTERIOR EXPOSED SURFACES WITH ONE COAT OF PRIMER PER 202.
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING
16NXXXX.
F TOUCH UP AS REQUIRED PER 235, 236, 242,(CONT'D IN NEXT STEP)
G (CONT'D FROM PREV STEP) 401, (OR 402 AS APPLICABLE), & 404.
A - 90

A808 PRIMER, FMS-3014 FORM TWO ADHESIVE PRIMER,
WHITE URETHANE, & 16NXXXX FINISH. BARE 2000
OR 7000 SERIES AL ALLOYS USED FOR LOWER WING SKINS
A ANODIZE NOTED SURFACES PER 114.
C APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO INTERIOR SURFACES
D PRIME EXTERIOR COVERED SURFACES (AS NOTED ON DRAWING) WITH
TWO COATS OF PRIMER PER 205 (OR 245).
E APPLY TEFLON-URETHANE COATING TO THE SPECIFIED PRIMED AREA
AS SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING
F PRIME EXTERIOR SURFACES EXPOSED IN COVE AREAS AND EXTERIOR
NON-COVERED SURFACES WITH ONE COAT OF PRIMER PER 202.
G APPLY WHITE URETHANE COATING TO EXTERIOR SURFACES EXPOSED IN
COVE AREAS PER 222 (OR 274).
H FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16NXXXX.
I TOUCH UP AS REQUIRED PER 235, 236, 237,(CONT'D IN NEXT STEP)
J (CONT'D FROM PREV STEP) 242, 298, AND 401 (OR 402 AS APPLICABLE).
A809 FMS-3014 FORM 2 ADHESIVE PRIMER AND GRAY URETHANE
C PRIME EXTERIOR SURFACES REQUIRING GRAY COLOR WITH ONE COAT OF PRIME
PER 202.
D PAINT SPECIFIED EXTERIOR SURFACES WITH GRAY COLOR NUMBER
36270 URETHANE COATING PER 290.
E TOUCH UP AS REQUIRED PER 291 AND 401 (OR 402 AS APPLICABLE).
A810 FMS-3014 FORM 2 ADHESIVE PRIMER AND WHITE URETHANE
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE; COLOR NO.17875
OR COLOR NO. 17925 PER 406.
D TOUCH UP AS REQUIRED PER 236, 401 (OR 402 AS APPLICABLE), AND 404.
A - 91

C PRIME REMAINING EXTERIOR SURFACES WITH ONE COAT OF PRIMER PER 202.
D PAINT SPECIFIED EXTERIOR SURFACES WITH TEFLON-URETHANE
COATING AS SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT PAINTING
DRAWING. (OVERSPRAY ONTO FAYING SURFACES IS NOT PERMITTED).
E FINISH REMAINING EXTERIOR SURFACES AFTER ASSEMBLY PER DRAWING
16NXXXX.
G (CONT'D FROM PREV STEP) 298, AND 401 (OR 402 AS APPLICABLE)
(FINISH INACTIVE FOR NEW DESIGN; USE A811.)
C PRIME REMAINING EXTERIOR SURFACES WITH ONE COAT OF PRIMER PER 202.
D PAINT SPECIFIED EXTERIOR SURFACES WITH TEFLON-URETHANE
COATING AS SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT PAINTING
DRAWING. (OVERSPRAY ONTO FAYING SURFACE IS NOT PERMITTED).
E FINISH SPECIFIED EXTERIOR SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
G (CONT'D FROM PREV STEP) 298, AND 401 (OR 402 AS APPLICABLE).
A813 FMS-3014 FORM 2 ADHESIVE PRIMER, WHITE ACRYLIC
C PRIME REMAINING SURFACES WITH ONE COAT OF PRIMER PER 202.
OR WHITE URETHANE COATING PER 407.
F TOUCH UP AS REQUIRED PER 235, 242, 401 (OR 402 AS APPLICABLE), AND 405.
B APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO INTERIOR SURFACES
AND SURFACES EXPOSED TO FUEL AS NOTED ON THE DRAWING PER 403
E TOUCH UP AS REQUIRED PER 235, 236, 242, AND 401 (OR 402 AS APPLICABLE).
A - 92

A815 PRIMER, FMS-3014 FORM 2 ADHESIVE PRIMER, AND WHITE URETHANE
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING; COLOR
NO. 17875 OR COLOR NO. 17925 PER 406.
D PRIME EXTERIOR EXPOSED SURFACES WITH ONE COAT OF PRIMER PER 202.
E TOUCH UP AS REQUIRED PER 235, 236, 242,(CONT'D IN NEXT STEP)
F (CONT'D FROM PREV STEP) 401 (OR 402 AS APPLICABLE) AND 404.
A816 PRIMER AND FMS-3014 FORM 2 ADHESIVE PRIMER
D TOUCH-UP AS REQUIRED PER 242 AND 401 (OR 402 AS APPLICABLE).
ALLOYS AND ALUMINUM CASTINGS (EXCEPT TUBING).
A818 FMS-3014 FORM 2 ADHESIVE PRIMER AND HARD ANODIZE
C APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO SPECIFIED SURFACES PER 403.
D TOUCH UP AS REQUIRED PER 401 (OR 402 AS APPLICABLE).
A819 FMS-3014 FORM 2 ADHESIVE PRIMER AND HARD ANODIZE
C APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO SPECIFIED SURFACES PER 403.
D TOUCH UP AS REQUIRED PER 401 (OR 402 AS APPLICABLE).
B APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO SPECIFIED SURFACES PER 403.
A - 93

ALLOYS AND ALUMINUM CASTINGS (EXCEPT TUBING)
A822 ALUMINUM TUBING ASSEMBLIES: FMS-3014 FORM 2
ADHESIVE PRIMER. 5000 & 6000 SERIES AL ALLOY
TUBING LOCATED IN FUEL AREA
A CHEM FILM EXTERIOR SURFACE ONLY PER 107.
B FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, APPLY FMS-3014
FORM 2 ADHESIVE PRIMER TO EXTERIOR SURFACE OF TUBING
ASSEMBLY EXCEPT OMIT COATING .50 INCH FROM THE FACE OF THE
FITTING UNLESS OTHERWISE SPECIFIED ON THE DRAWING (OMIT 1.0
INCH MAXIMUM) PER 403. TOUCH UP AS REQUIRED PER 401, BUT
TOUCHUP ACROSS THE ASSEMBLED JOINT IS NOT PERMITTED.
APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO EXTERIOR SURFACE
OF TUBING ASSEMBLY, EXCEPT OMIT COATING AS SPECIFIED PER
408. AFTER INSTALLATION, TOUCH UP OR COMPLETE REQUIRED
FINISH INCLUDING ACROSS ASSEMBLED JOINT PER 401.
APPLY FMS-3014 FORM 2 ADHESIVE PRIMER ON EXTERIOR SURFACE OF
TUBE TO THE BASE OF SLEEVE PER 409. AFTER INSTALLATION,
TOUCH UP OR COMPLETE REQUIRED FINISH INCLUDING ACROSS
ASSEMBLED JOINT PER 401.
A823 PRIMER
D NOTE: FOR APPLICATION OF FMS-3049 COATING; SEE MATERIALS
AND PROCESSES ENGINEERING FOR USE.
A850 WHITE TEFLON-URETHANE AND 16NXXXX FINISH
C PAINT SPECIFIED SURFACES WITH TWO COATS OF FMS-1027 TYPE 5
TEFLON-URETHANE, WHITE COLOR NO. 17875 (OR 17925) PER 351.
D FINISH EXTERIOR SURFACES AFTER ASSEMBLY PER 16NXXXX.
A - 94

A851 LIGHT GRAY URETHANE AND HARD ANODIZE
C PRIME SPECIFIED SURFACES WITH ONE COAT OF PRIMER PER 202.
D PAINT SPECIFIED SURFACES WITH TWO COATS OF MIL-C-83286
URETHANE COATING; LIGHT GRAY, COLOR NUMBER 36375 PER 254.
B APPLY ONE COAT OF PRIMER TO SPECIFIED SURFACE PER 202.
C PAINT SPECIFIED SURFACES WITH LIGHT GRAY URETHANE PER 254.
A853 ALUMINUM TUBING ASSEMBLIES: PRIMER, WHITE URETHANE
AND 16NXXXX FINISH. 5000, 6000 SERIES ALUMINUM ALLOYS.
A ANODIZE OUTER SURFACES PER 140.
B PRIME ONE COAT OUTER SURFACE ONLY IN SPECIFIED AREAS PER 202
C PRIME EXTERIOR EXPOSED SURFACES AND AREA TO BE PAINTED WITH
WHITE URETHANE ONE COAT PER 202.
D PAINT WITH WHITE URETHANE COATING IN SPECIFIED AREAS PER 222
E FINISH SPECIFIED EXTERIOR EXPOSED SURFACE (AFTER ASSEMBLY) PER
DRAWING 16N0001.
A854 ALUMINUM TUBING ASSEMBLIES.
5000 AND 6000 SERIES ALUMINUM ALLOYS LOCATED IN
FUEL AREAS - ANODIZE SPECIFIED AREAS ONLY.
WHERE NO CREVICE EXISTS, ANODIZE, SPECIFIED EXTERIOR SURFACES PER 501.
B CHEM FILM SPECIFIED SURFACES PER 178.
A855 PRIMER AND NICKEL-CADMIUM PLATE.
CLAD OR 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS.
A CHEM FILM SPECIFIED SURFACES PER 502.
C ELECTROLESS NICKEL PLATE SPECIFIED SURFACES PER 503.
D CADMIUM PLATE NICKEL PLATED SURFACES PER 504.
E (INACTIVE FOR NEW DESIGN).
A856 DARK GRAY URETHANE AND 16NXXXX FINISH.
BARE 2000 & 7000 SERIES ALUMINUM ALLOYS.
PER 257 (OR 277).
A - 95

A857 WHITE URETHANE, SOLID FILM LUBRICANT AND 16N0001 FINISH-
HARD ANODIZE.
C APPLY SOLID FILM LUBE TO HARD ANODIZED SURFACES PER 207.
D PRIME REMAINING SURFACES 1 COAT PER 202.
E PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222.
F FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER 16N0001.
G TOUCH-UP AS REQUIRED PER 235, 237 AND 362.
A858 PRIMER, SOLID FILM LUBRICANT AND 16N0001 FINISH-HARD ANODIZE.
C APPLY SOLID FILM LUBE TO HARD ANODIZED SURFACES PER 207.
D PRIME SPECIFIED SURFACES 2 COATS PER 205.
E PRIME SPECIFIED SURFACES 1 COAT PER 202.
G TOUCH AS REQUIRED PER 235, 236 AND 362.
A859 PRIMER AND SOLID FILM LUBRICANT - HARD ANODIZE.
C APPLY SOLID FILM LUBRICANT TO HARD ANODIZED SURFACES PER 207
D PRIME TWO COATS REMAINING SURFACES PER 205.
A860 PRIMER, SOLID FILM LUBRICANT AND 16N0005 FINISH - HARD ANODIZE
C APPLY SOLID FILM LUBE TO HARD ANODIZE SURFACES PER 207.
D PRIME SPECIFIED SURFACES 2 COATS PER 205.
E PRIME REMAINING SURFACES 1 COAT PER 202.
G TOUCH UP AS REQUIRED PER 235, 236 AND 362.
A861 GRAY URETHANE
C PAINT PRIMED SURFACES WITH TWO COATS OF GRAY URETHANE COATING
PER 290.
A - 96

B PRIME EXTERIOR SURFACES TWO COATS PER 205.
FUEL PER 221.
A863 AMS-C-27725 FUEL TANK COATING, PRIMER, AND 16NXXXX FINISH.
FUEL PER 221.
C PRIME EXTERIOR SURFACES TWO COATS PER 205.
A864 SOLID FILM LUBRICANT, PRIMER, AND AMS-C-27725
FUEL TANK COATING - HARD ANODIZE.
C APPLY SOLID FILM LUBRICANT TO HARD ANODIZE SURFACES PER 207.
D PRIME INTERIOR NON-FUEL SURFACES AND SURFACES NOT HARD ANODIZED
PER 205 (OR 245).
E APPLY AMS-C-27725 COATING ON FAYING SURFACES AND SURFACES EXPOSED TO
FUEL PER 221.
A865 PRIMER, AMS-C-27725 FUEL TANK COATING, AND SOLID FILM LUBRICANT.
B APPLY SOLID FILM LUBRICANT TO SPECIFIED SURFACES PER 207.
C PRIME INTERIOR NON-FUEL SURFACES TWO COATS PER 205 (OR 245).
D APPLY AMS-C-27725 COATING ON FAYING SURFACES AND SURFACES EXPOSED TO
FUEL PER 221.
A866 SOLID FILM LUBRICANT AND FMS-1058-1 PRIMER- HARD ANODIZE.
C APPLY SOLID FILM LUBRICANT TO HARD ANODIZED SURFACES PER 207
D APPLY TWO COATS OF FMS-1058-1 TO SPECIFIED SURFACES PER 506.
A - 97

16NXXXX FINISH, AND FMS-1058-1.
C APPLY FMS-1058-1 TO SPECIFIED SURFACES PER 506.
D PRIME ONE COAT ON SPECIFIED SURFACES PER 202.
E PRIME TWO COATS ON SPECIFIED EXTERIOR COVERED SURFACES
PER 205 (OR 245).
F APPLY DARK GRAY TEFLON-URETHANE COATING (OR COLOR SPECIFIED
BY THE APPLICABLE 16NXXXX DRAWING) ON SPECIFIED SURFACES PER 259
G APPLY WHITE URETHANE COATING ON EXTERIOR SURFACES EXPOSED IN COVE
AREA PER 222 (OR 274).
H FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING 16N0001.
I TOUCH UP AS REQUIRED PER 235, 236, 237,(CONT'D IN NEXT STEP)
J (CONT'D FROM PREV STEP) 240, 242, 298, AND 507.
A868 REWORK OF UPPER WING SKIN - BRUSH CHEM FILM AND FMS-1058-1.
A CLEAN AND BRUSH CHEM FILM SPECIFIED SURFACES PER 134.
B SCUFF SAND SPECIFIED AREAS PER 119.
C APPLY FMS-1058-1 TO SPECIFIED SURFACES PER 506.
A869 PRIMER. CLAD AND 1000, 3000, 5000, AND 6000
SERIES ALUMINUM ALLOYS.
A870 FMS-3014 FORM 2 ADHESIVE PRIMER - HARD ANODIZE
ALL ALUMINUM ALLOYS
NOTE: DO NOT USE WITHOUT MATERIALS AND PROCESSES ENGINEERING
APPROVAL.
A871 GARY URETHANE
C PAINT ALL SURFACES WITH TWO COATS OF GRAY URETHANE COATING PER 289.
A - 98

A872 RED URETHANE, SOLID FILM LUBRICANT, AND HARD ANODIZE
ALL ALUMINUM ALLOYS
D PAINT PRIMED SURFACES WITH TWO COATS OF RED URETHANE PER 512.
A873 WHITE URETHANE
(USE FOR ELECTRICAL BONDING)
A CHEM FILM SPECIFIED SURFACES PER 178.
F (INACTIVE FOR NEW DESIGN.)
A874 WHITE URETHANE
CLAD & 1000, 3000, 5000, 6000 SERIES AL ALLOYS &
AL ALLOY CASTINGS (USE FOR ELECTRICAL BONDING)
A875 CHEMICAL FILM
A876 FMS-1058-1 PRIMER - HARD ANODIZE
C APPLY TWO COATS OF FMS-1058-1 TO SPECIFIED SURFACES PER 506.
A877 P6096-2 FLAT BLACK URETHANE & BLACK EPOXY ENAMEL/BLACK URETHANE.
CLAD & 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND CASTINGS.
B PRIME SURFACES REQUIRING URETHANE OR EPOXY ENAMEL ONE COAT PER 202.
C PAINT SPECIFIED SURFACES WITH P6096-2 FLAT BLACK URETHANE
PER 217 (OR 286).
PER 213.
A - 99

A878 BLACK EPOXY ENAMEL/URETHANE. CLAD & 1000, 3000, 5000, OR
6000 SERIES ALUMINUM. (USE ONLY FOR ELECTRICAL
BONDING OF PARTS W/STEEL OR WIRE INSERTS).
C PAINT PRIMED SURFACES WITH BLACK EPOXY ENAMEL OR BLACK URETHNE
PER 213.
CLAD AND 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND
ALUMINUM ALLOY CASTINGS.
C PAINT SPECIFIED SURFACES WITH BLACK EPOXY ENAMEL OR BLACK
URETHANE COATING PER 213.
A880 BLACK EPOXY ENAMEL/BLACK URETHANE AND SOLID FILM LUBRICANT.
CLAD AND 1000, 3000, 5000, OR 6000 SERIES ALUMINUM ALLOYS AND CASTINGS.
D PAINT PRIMED SURFACES WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
A881 LUSTERLESS GRAY URETHANE. CLAD AND 1000,
3000, 5000, OR 6000 SERIES ALUM. ALLOYS & ALUM.
ALLOY CASTINGS. (USE FOR ELECTRICAL BONDING)
C PAINT PRIMED SURFACES WITH LUSTERLESS GRAY URETHANE PER 282 (OR 280).
A882 REWORK OF ANODIZED PART - BLACK EPOXY ENAMEL/
BLACK URETHANE. ALL ALUMINUM ALLOYS
A CLEAN AND BRUSH CHEM FILM ALUMINUM SURFACES PER 134.
PER 213.
A883 WHITE URETHANE
A CLEAN AND PREPARE EXPOSED INTERIOR SURFACES AND EXTERIOR
SURFACES OF THE DOOR AND HINGE PER 297.
B PAINT THE EXPOSED INTERIOR SURFACES AND EXTERIOR SURFACES
WITH WHITE URETHANE COATING PER 222.
C TOUCH UP AS REQUIRED PER 235 AND 237.
A - 100

A884 REWORK OF CHEMICAL FILMED PARTS - PRIMER
ALL ALUMINUM ALLOYS
A BRUSH CHEM FILM SPECIFIED SURFACES PER 134 OR STRIP AND REAPPLY
CHEM FILM PER 514.
NOTE: THIS CODE IS INTENDED FOR PREVIOUSLY CHEM FILMED PARTS.
DO NOT USE WITHOUT MATERIALS AND PROCESSES ENGINEERING
APPROVAL.
A885 PRIMER, WHITE URETHANE, AND 16NXXXX
FINISH - HARD ANODIZE.
ALL ALUMINIM ALLOYS.
B CHEM FILM SURFACES NOT ANODIZED PER 134.
C PRIME SURFACES SPECIFIED FOR PRIMER TWO COATS PER 205.
D PRIME AREAS SPECIFIED FOR WHITE URETHANE AND CHEM FILMED EX-
TERIOR EXPOSED SURFACES ONE COAT PER 202.
E PAINT SPECIFIED SURFACES W/WHITE URETHANE PER 222 (OR 274).
A886 PRIMER, LIGHT GRAY URETHANE, AND 16NXXXX FINISH
B PRIME TWO COATS SPECIFIED INTERIOR SURFACES PER 205(OR 245).
D PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT GRAY URETHANE COATING
PER 254 (OR 276).
A887 16NXXXX FINISH
ALUMINUM ALLOY CASTINGS AND 1000, 3000, 5000, 6000 SERIES
ALUMINUM ALLOYS
C PAINT SPECIFIED INTERIOR SURFACES WITH TWO COATS OF URETHANE
COATING OF THE COLOR SPECIFIED ON THE APPLICABLE 16NXXXX
AIRCRAFT PAINTING DRAWING.
A888 PRIMER AND LUSTERLESS BLACK URETHANE
CLAD AND 1000, 3000, 5000 AND 6000 SERIES ALUMINUM ALLOYS
C PAINT SPECIFIED SURFACES WITH LUSTERLESS BLACK URETHANE
PER 283 (OR 281).
A - 101

A889 ALUMINUM TUBING ASSEMBLIES - 5000 AND 6000 SERIES
ALUMINUM ALLOYS LOCATED IN FUEL AREA
WHERE NO CREVICE EXISTS, HARD ANODIZE SPECIFIED SURFACES PER 115.
B FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, CHEM FILM THE FIRST
0.50 INCH OF TUBE END THAT RECEIVES A C7551 FITTING PER 178.
THE CHEM FILM TREATMENT IS REQUIRED ON EXTERIOR SURFACES;
TREATMENT IS OPTIONAL ON INSIDE SURFACES.
C ANODIZE REMAINING EXTERIOR SURFACES PER 140.
A890 FMS-1058-1 PRIMER - HARD ANODIZE
A HARD ANODIZE ALL SUFACES PER 113.
B APPLY TWO COATS OF FMS-1058-1 PRIMER TO SPECIFIED SURFACES PER 506.
A891 PRIMER AND P6096-2 FLAT BLACK URETHANE CLAD AND
1000, 3000, 5000 OR 6000 SERIES ALUMINUM ALLOYS
C PAINT SPECIFIED SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 217.
A892 WHITE URETHANE, 16NXXXX FINISH (OVER SOLID FILM
LUBRICANT). HARD ANODIZE (OMITTING AREAS FOR ELECTRICAL GROUND).
A HARD ANODIZE ALL SURFACES NOT SPECIFIED FOR ELECTRICAL BONDING
PER 115.
B APPLY SOLID FILM LUBRICANT TO ALL EXTERIOR SURFACES PER 207.
C CLEAN PER FPS-3001 PARAGRAPH 3.1.1 AND BRUSH CHEM-FILM ELEC-
TRICAL BONDING SURFACES PER MIL-C-5541, CLASS 3, PER 178.
D PRIME REMAINING SURFACES WITH ONE COAT PER 202.
E PAINT INTERIOR SURFACES NOT SPECIFIED FOR ELECTRICAL BONDING
WITH WHITE URETHANE PER 222.
F PAINT ALL EXTERIOR SURFACES PER 16NXXXX.
G TOUCH-UP AS REQUIRED 237, 242, 298, 362.
H CLAD AND 1000, 3000, 5000, AND 6000 SERIES ALUMINUM AND ALUMINUM
CASTINGS.
PER 257 (OR 277).
A - 102

C PAINT SPECIFIED INTERIOR SURFACES WITH GRAY COLOR 36270
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER THE APPLIC-
ABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
A895 PRIMER AND GRAY URETHANE COLOR NO. 36270
C PAINT SPECIFIED SURFACES WITH 36270 GRAY URETHANE PER 290.
A896 ALUMINUM TUBING ASSEMBLIES: GRAY COLOR NO. 36270
F PAINT PRIMED SURFACES WITH ONE COAT OF GRAY COLOR NO. 36270 PER 290.
A - 103

GRAY URETHANE, AND IVD ALUMINUM OR CAD PLATE
2000 AND 7000 SERIES ALUM (SPECIAL ELEC BOND APPL)
A ANODIZE ALL SURFACES PER 111 EXCEPT THOSE SUR-
FACES SPECIFIED FOR IVD ALUMINUM OR CADMIUM PLATE, OR
SURFACES SPECIFIED FOR ELECTRICAL BONDING PER FPS-3024.
B CLEAN SURFACES SPECIFIED FOR IVD ALUMINUM OR CAD PLATE PER
FPS-3001 PARA. 3.1.1.(A). IVD ALUMINUM TREAT PER
MIL-C-83488 TYPE II CL2 OR CADMUIM PLATE PER MIL-C-8837
TYPE II CL1 SPECIFIED SURFACES.
C PRIME ONE COAT SURFACES SPECIFIED FOR WHITE ACRYLIC LACQUER/
WHITE URETHANE AND LUSTERLESS GRAY URETHANE PER 202.
E PAINT REMAINING PRIMED SURFACES WITH LUSTERLESS GRAY URE-
THANE COATING PER 282 (OR 280).
G
APPROVAL.
A898 WHITE ACRYLIC LACQUER/WHITE URETHANE AND IVD ALUM
OR CAD PLATE (SPECIAL ELEC BONDING APPLICATION)
A ANODIZE ALL SURFACES PER 111 EXCEPT THOSE SUR-
FACES SPECIFIED FOR IVD ALUMINUM OR CADMIUM PLATE.
B CLEAN SURFACES SPECIFIED FOR IVD ALUM OR CAD PLATE PER FPS-
3001 PARA. 3.1.1(A). IVD ALUMINUM TREAT PER MIL-C-83488
TYPE II CL2 OR CADMIUM PLATE PER MIL-C-8837 TYPE II CL1. SPECIFIED
SURFACES.
D PAINT PRIMED SURFACES WITH EITHER WHITE ACRYLIC LACQUER OR
F
APPROVAL.
A899 PRIMER AND IVD ALUMINUM OR CADMIUM PLATE (SPECIAL
ELECTRICAL BONDING APPLICATION)
A CLEAN ALL SURFACES PER FPS-3001 PARA. 3.1.1(A).
B IVD ALUMINUM TREAT PER MIL-C-83488 TYPE II CL2 OR
CADMIUM PLATE PER MIL-C-8837 TYPE II CL1.
C PRIME ALL SURFACES PER 205 EXCEPT THOSE SURFACES SPECIFIED
FOR ELECTRICAL BONDING PER FPS-3024.
APPROVAL.
A - 104

A900 PRIMER AND EXTERIOR SURFACE WITH NO TOPCOAT
(USED ON FS-X/F-2 PARTS W/TOPCOAT APPLIED AFTER
ASSY) BARE 2000 AND 7000 SERIES ALUMINUM ALLOYS
A901 AMS-C-27725 FUEL TANK COATING AND EXTERIOR SURFACE
WITH NO TOPCOAT (USED ON FS-X/F-2 PARTS)
B APPLY AMS-C-27725 COATING ON FAYING SURFACES AND SURFACES
EXPOSED TO FUEL PER 221 (INTERIOR SURFACES AS SPECIFIED ON THE
ENGINEERING DRAWING).
A902 FMS-3014 FORM 2 ADHESIVE PRIMER AND EXTERIOR
SURFACE WITH NO TOPCOAT APPLIED (FS-X/F-2 PROG.)
D TOUCH UP PER 242 AND 401 (OR 402 AS APPLICABLE).
A903 PRIMER, FMS-3014 FORM 2 ADHESIVE PRIMER, & EXT.
SURF. WITH NO TOPCOAT APPLIED (FS-X/F-2 PROG.)
C PRIME SURFACE SPECIFIED FOR PRIMER ONLY WITH TWO COATS OF PRIMER
PER 205.
D PRIME SPECIFIED EXTERIOR EXPOSED SURFACES WITH ONE COAT OF PRIMER
PER 202.
E TOUCH UP AS REQUIRED PER 236, 242, AND 401 (OR 402 AS APPLICABLE.
A904 PRIMER WITH TOPCOAT APPLIED AFTER ASSEMBLY (FOR FS-X/F-2 PARTS)
A - 105

A905 PRIMER ON SPECIFIED SURFACES. TOPCOAT APPLIED AFTER ASSY
(FOR FS-X/F-2 PARTS)
A906 WHITE URETHANE ON SPECIFIED SURFACES (FOR FS-X/
F-2 PARTS). ALUMINUM CASTINGS AND 1000, 3000,
5000, AND 6000 SERIES AND CLAD ALUMINUM ALLOYS
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE TOPCOAT PER 222.
A907 LIGHT GRAY URETHANE ON SPECIFIED SURFACES
(FOR FS-X/F-2 PARTS) ALUM. CASTINGS AND 1000, 3000, 5000
AND 6000 SERIES AND CLAD ALUMINUM ALLOYS
C PAINT PRIMED SURFACES WITH LIGHT GRAY URETHANE COATING
PER 254 (OR 276).
D TOUCH UP AS REQUIRED PER PER 255.
A908 PRIMER WITHOUT TOPCOAT (FOR FS-X/F-2 USE)
CLAD AND 1000, 3000, 5000, AND 6000 SERIES ALUM. ALLOYS AND
ALUMINUM CASTINGS
A909 WHITE URETHANE AND EXTERIOR SURFACE WITH NO TOP-
COAT (USED ON FS-X/F-2 PARTS W/TOPCOAT APPLIED
AFTER ASSY) BARE 2000 AND 7000 SERIES ALUM ALLOYS
PER 222 (OR 274).
A - 106

A910 WHITE URETHANE (ACCOUNTS FOR PREVIOUSLY PAINTED SURFACES)
A FOR UNFINISHED PARTS, PROCEED AS FOLLOWS (FOR PREVIOUSLY
PRIMED OR PAINTED PARTS, START WITH STEP E).
C PRIME ONE COAT ALL SURFACES PER 201.
D PAINT ALL SURFACES PER STEP H.
E SCUFF SAND PREVIOUSLY PRIMED OR PAINTED PARTS USING 320 GRIT
ABRASIVE TO REMOVE SURFACE GLOSS.
F WIPE SURFACES WITH CLEAN CHEESE CLOTH MOISTENED WITH MIL-C-38736
OR FMS-2004 CLEANER.
G APPLY A THIN COAT OF MIL-PRF-23377 PRIMER OR MIL-PRF-85582
VOC COMPLIANT EPOXY PRIMER TO ALL SURFACES.
H PAINT PRIMED SURFACES WITH WHITE URETHANE PER 223.
I TOUCH UP AS REQUIRED PER 237.
A911 WHITE URETHANE (SPECIAL)
PREVIOUSLY PRIMED PARTS IN AN ASSEMBLY
A PREVIOUSLY PRIMED SPECIFIED SURFACES SHALL BE SOLVENT
CLEANED WITH MIL-C-38736 OR FMS-2004, SCUFFED TO REMOVE
GLOSS WITH 320 GRIT ABRASIVE, RE-WIPED WITH SOLVENT CLEANER,
AND MIST COATED WITH MIL-PRF-23377 OR MIL-PRF-85582 PRIMER.
B PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING PER 222
C TOUCH UP AS REQUIRED PER 236 AND 237.
A912 WHITE URETHANE (ACCOUNTS FOR PREVIOUSLY PAINTED
SURFACES) CLAD OR 1000, 3000, 5000 AND 6000 SERIES
B CHEM FILM ALL SURFACES PER 105.
A - 107

A913 WHITE URETHANE (ACCOUNTS FOR PREVIOUSLY PAINTED SURFACES)
C PRIME ONE COAT ALL SURFACES EXCEPT EXPOSED SURFACES OF
LUBRICATION FITTINGS AND BUSHINGS PER 202.
D PAINT PRIMED SURFACES PER STEP H.
VOC COMPLIANT EPOXY PRIMER TO ALL SURFACES EXCEPT THE
EXPOSED SURFACES OF LUBRICATION FITTINGS AND BUSHINGS.
A914 ORANGE URETHANE. FOR FS-X/F-2 INSTRUMENTATION ONLY.
C PAINT ALL SURFACES WITH MIL-C-83286 OR MIL-C-85285 URETHANE
COATING, COLOR NO. 12197 PER FED-STD-595. TOPCOAT MAY BE
DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL.
D TOUCH UP AS REQUIRED PER 242 USING AN ADDITIONAL TOPCOAT OF
MIL-C-83286 OR MIL-C-85285 URETHANE COATING, COLOR NO. 12197 PER
FED-STD-595.
A915 P6096-2 ON SPECIFIED INTERIOR SURFACES. TOPCOAT
APPLIED AFTER ASSEMBLY. (FOR FS-X/F-2 PARTS)
C PAINT SPECIFIED INTERIOR SURFACES WITH P6096-2 FLAT BLACK URETHANE
PER 217.
A921 IVD ALUMINUM COATING OR CADMIUM PLATING OF ALUMINUM ALLOYS
(SPECIAL ELECTRICAL BONDING APPLICATION)
A CLEAN ALL SURFACES PER FPS-3001 PARA. 3.1.1(A)
B IVD ALUMINUM TREAT ALL SURFACES PER MIL-C-83488 TYPE II,
CLASS 3, OR VACUUM CADMIUM PLATE PER MIL-C-8837, TYPE II, CLASS 2.
APPROVAL.
A - 108

A922 AMS-C-27725 FUEL TANK COATING, LUSTERLESS GRAY
URETHANE, WHITE URETHANE, AND PRIMER
C PRIME TWO COATS ON SURFACES SPECIFIED FOR PRIMER ONLY PER 205.
F PAINT SPECIFIED SURFACES WITH LUSTERLESS GRAY URETHANE PER 282 (OR 280).
A923 ALUMINUM TUBING ASSEMBLIES: WHITE URETHANE AND
PRIMER. PNEUMATIC, AIR DATA, HYDRAULICS AND FUEL TUBING.
F PAINT SPECIFIED SURFACES WITH TWO COATS OF WHITE URETHANE COATING
PER 222.
H FOR TUBE ASSEMBLIES WITH "PERMASWAGE","DYNATUBE", OR FLARED
A924 FMS-1058-1 PRIMER. 2000, 5000, 6000 AND 7000
SERIES ALUMINUM TUBING. (FOR FS-X/F-2 WIRING
CONDUIT ROUTED THRU FUEL AREA)
B DIP COAT ALL SURFACES WITH FMS-1058-1 EPOXY AMINE PRIMER, EXCEPT
WHERE SPECIFIED.
C TOUCH UP AS APPLICABLE PER 240.
A - 109

A925 PRIMER AND WHITE URETHANE 16NXXXX FINISH CLAD AND
1000, 3000, 5000, AND 6000 SERIES ALUMINUM ALLOY AND
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING PER 222 OR 274.
D PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE COATING PER
257 OR 277. PRODUCTION AIRCRAFT SHALL USE THE COLOR OF
PAINTING DRAWING.
F TOUCH UP AS REQUIRED PER 237, 242 AND 258 AS APPLICABLE.
TOUCH UP AS REQUIRED ON PRODUCTION AIRCRAFT PER 298.
A926 PRIMER AND 16NXXXX FINISH FOR SPECIAL ELECTRICAL
BONDING APPLICATIONS.
A CHEM FILM SPECIFIED SURFACES FOR ELECTRICAL BONDING PER 178.
B ANODIZE ALL OTHER SURFACES PER 111.
C PRIME TWO COATS ON INTERIOR SURFACE PER 205 (OR 245)
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER DRAWING
16N0001, EXCEPT ELECTRICAL BOND AREA.
A927 PRIMER, WHITE URETHANE, AND 16NXXXX FINISH FOR
SPECIAL ELECTRICAL BONDING APPLICATIONS.
A CHEM FILM SPECIFIED SURFACES FOR ELECTRICAL BONDING PER 178.
B ANODIZE ALL OTHER SURFACES PER 111.
C PRIME SURFACES SPECIFIED FOR PRIME TWO COATS PER 205 (OR 245).
D PRIME REMAINING SURFACES, EXCEPT ELECTRICAL BOND AREA ONE COAT
PER 202.
E PAINT SPECIFIED SURFACES PER 16NXXXX DRAWING.
F PAINT SPEDIFIED SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
G TOUCH UP AS REQUIRED PER 236, 237 AND 298.
A928 PRIMER AND 6069-2; REWORK OF DETAIL PART AT ASSEMBLY.
A REACTIVATE CHEM FILMED SURFACES PER 105.
A929 GRAY URETHANE AND 16NXXXX FINISH - PYLONS
A ANODIZE ALL SURFACES PER 111 OR 112.
PER 290 (OR 292).
A - 110

A930 WHITE URETHANE (FOR F-2 USE ONLY)
FINAL COMPONENT PRIME AND PAINT
A PREVIOUSLY PRIMED EXTERIOR SURFACES SHALL BE SOLVENT
B PRIME SPECIFIED EXTERIOR SURFACES ONE COAT PER 366.
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING PER 222
A931 AMS-C-27725 FUEL TANK COATING AND HARD ANODIZE
C APPLY AMS-C-27725 COATING ON SPECIFIED FAYING SURFACES AND
A932 AMS-C-27725 FUEL TANK COATING, WHITE URETHANE,

AND 16NXXXX FINISH – ALUMINUM CASTINGS
D PAINT SPECIFIED AREAS WITH WHITE URETHANE COATING PER 222
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER DRAWING 16NXXXX.
A933 BLUE URETHANE
CLAD OR 1000, 3000, 5000 AND 6000 SERIES ALUMINUM ALLOYS AND CASTINGS
C PAINT ALL SURFACES WITH BLUE URETHANE COATING PER 379 (OR 381).
A934 BLUE URETHANE (FOR F-2 PARTS)
ALUMINUM CASTINGS AND 1000, 3000, 5000, AND 6000 SERIES AND CLAD
ALUMINUM ALLOYS
C PAINT SPECIFIED SURFACES WITH BLUE URETHANE TOPCOAT PER 378.
A935 BLUE URETHANE AND EXTERIOR SURFACE WITH NO TOP-
COAT (USED ON F-2 PARTS WITH TOPCOAT APPLIED
AFTER ASSY) BARE 2000 AND 7000 SERIES ALUM ALLOYS
C PAINT SPECIFIED INTERIOR SURFACES WITH BLUE URETHANE COATING
PER 378 (OR 381).
A - 111

A936 BLUE URETHANE (ACCOUNTS FOR PREVIOUSLY PAINTED SURFACES)
H PAINT PRIMED SURFACES WITH BLUE URETHANE PER 379.
A937 BLUE URETHANE (ACCOUNTS FOR PREVIOUSLY PAINTED
SURFACES) CLAD OR 1000,3000,5000 AND 6000 SERIES
B CHEM FILM ALL SURFACES PER 105.
A - 112

A938 BLUE URETHANE (ACCOUNTS FOR PREVIOUSLY PAINTED SURFACES)
C PRIME ONE COAT ALL SURFACES EXCEPT EXPOSED SURFACES OF
LUBRICATION FITTINGS AND BUSHINGS PER 202.
D PAINT PRIMED SURFACES PER STEP H.
VOC COMPLIANT EPOXY PRIMER TO ALL SURFACES EXCEPT THE
EXPOSED SURFACES OF LUBRICATION FITTINGS AND BUSHINGS.
A939 BLUE AND WHITE URETHANE (FOR F-2 USE ONLY)
FINAL COMPONENT PRIME AND PAINT
A PREVIOUSLY PRIMED EXTERIOR SURFACES SHALL BE SOLVENT
B PRIME SPECIFIED EXTERIOR SURFACES ONE COAT PER 366.
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING PER 222
D PAINT SPECIFIED SURFACES WITH BLUE URETHANE COATING PER 378.

ALUMINUM CASTINGS
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER DRAWING 16NXXXX.
A - 113

A941 ALUMINUM TUBING ASSEMBLIES: WHITE URETHANE AND 16NXXXX FINISH
PNEUMATIC, AIR DATA, HYDRAULICS, & FUEL TUBING.
A CHEM FILM EXTERIOR SURFACE OF TUBING ASSEMBLY PER 107.
F PAINT SPECIFIED SURFACES WITH TWO COATS OF WHITE URETHANE COATING
PER 224.
G FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER THE
APPLICABLE 16NXXXX PAINTING DRAWING.
H FOR TUBE ASSEMBLIES WITH C7551 FITTINGS, TOUCH UP AS
I FOR TUBE ASSEMBLIES WITH "PERMASWAGE", "DYNATUBE", OR FLARED
A942 UNIFORM PRIMER APPLICATION (FOR F-2 USE ONLY)
A PREVIOUSLY PRIMED SURFACES SHALL BE SOLVENT
B TOUCH UP AS REQUIRED PER 236.
A943 AMS-C-27725 FUEL TANK COATING, WHITE ACRYLIC
C PRIME ONE COAT SPECIFIED INTERIOR SURFACES PER 202.
E PRIME ONE COAT EXTERIOR EXPOSED SURFACES PER 202.
A - 114

C PAINT SPECIFIED SURFACES WITH DARK GRAY URETHANE COATING PER 527.
A945 WHITE URETHANE, P6255 COATING, AND 16NXXXX FINISH
C PAINT SPECIFIED INTERIOR SURFACES WITH WHITE URETHANE
COATING PER 222 (OR 274).
D APPLY FMS-3049 COATING TO SPECIFIED SURFACES PER 532.
E PAINT SPECIFIED SURFACES WITH P6255 COATING PER ENGINEERING
REPORT 16ER2032.
F FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER THE
G TOUCH UP AS REQUIRED PER 237, AND ENGINEERING REPORT 16ER2032.
C PAINT ONE COAT ON SPECIFIED SURFACES WITH GRAY EPOXY ENAMEL
A947 LIGHT GRAY URETHANE AND 16NXXXX FINISH – PYLON
PER 254 (OR 276).
F NOTE: FOR APPLICATION OF FMS-3049 COATING; SEE MATERIALS
D PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT GRAY URETHANE
A - 115

A949 LIGHT GRAY URETHANE AND 16NXXXX FINISH – PYLON
PER 254 (OR 276).
A950 PRIMER, LIGHT GRAY URETHANE, AND 16NXXXX FINISH
D PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT GRAY URETHANE
G NOTE: FOR APPLICATION OF FMS-3049 COATING; SEE MATERIALS
A951 PRIMER AND 16NXXXX FINISH – PYLONS
B PRIME ONE COAT EXTERIOR EXPOSED SURFACES PER 535.
C FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER
DRAWING 16N0005.
D PRIME TWO COATS REMAINING SURFACES, UNLESS OTHERWISE
SPECIFIED, PER 538 (OR 245).
A952 PRIMER, LIGHT GRAY URETHANE, 16NXXXX FINISH, HARD
ANODIZE - PYLONS. 2000 AND 7000 SERIES ALUMINUM ALLOYS.
E PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT GRAY URETHANE
H NOTE: FOR APPLICATION OF FMS-3049 COATING; SEE MATERIALS
A - 116

A953 WHITE URETHANE, P6255 COATING, AND 16NXXXX FINISH
AND CASTINGS
PER 222 (OR 274).
D APPLY FMS-3049 COATING TO SPECIFIED SURFACES PER 532.
E PAINT SPECIFIED SURFACES WITH P6255 COATING PER ENGINEERING
REPORT 16ER2032.
F FINISH EXTERIOR EXPOSED SURFACES AFTER ASSY PER THE
G TOUCH UP AS REQUIRED PER 237, AND ENGINEERING REPORT 16ER2032.
A954 LIGHT SEMIGLOSS GRAY URETHANE

C PAINT ALL SURFACES WITH LIGHT SEMIGLOSS GRAY URETHANE COATING
PER 541 (OR 542).
A955 PRIMER AND LIGHT SEMIGLOSS GRAY URETHANE

2000 AND 7000 SERIES ALUMINUM ALLOYS - PYLONS
B PRIME TWO COATS EXTERIOR SURFACES PER 538 (OR 245).
C PRIME ONE COAT INTERIOR SURFACES PER 535.
D PAINT INTERIOR SURFACES WITH LIGHT SEMIGLOSS GRAY URETHANE COATING
PER 544 (OR 547).
A956 PRIMER AND LIGHT SEMIGLOSS GRAY URETHANE – PYLONS

C PAINT INTERIOR SURFACES WITH LIGHT SEMIGLOSS GRAY URETHANE
E NOTE: FOR APPLICATION OF FMS-3049 COATING; SEE MATERIALS
A - 117

A957 PRIMER, LIGHT SEMIGLOSS GRAY URETHANE, AND 16NXXXX
FINISH – PYLON. ALUMINUM ALLOY CASTINGS
D PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT SEMIGLOSS GRAY
A958 PRIMER, LIGHT SEMIGLOSS GRAY URETHANE, 16NXXXX

FINISH, HARD ANODIZE - PYLONS
E PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT SEMIGLOSS GRAY
H NOTE: FOR APPLICATION OF FMS-3049 COATING; SEE MATERIALS
A959 WHITE URETHANE – CLAD OR 1000, 3000, 5000, AND 6000 SERIES
ALUMINUM ALLOYS AND CASTINGS
A - 118

A960 BLUE AND WHITE URETHANE FINAL FINISH
(FOR F-2 USE ONLY)
A PREVIOUSLY PRIMED EXTERIOR SURFACES SHALL BE ACETONE (ASTM D329)
WIPED FOLLOWED BY SCUFF SANDING WITH 180 GRIT OR FINER ABRASIVE,
AND ALKALINE CLEANED WITH MIL-PRF-87937 CLEANING COMPOUND.
B SPRAY CHEMICAL FILM ON ALL SCUFFED SURFACES PER MIL-C-5541.
C ACETONE (ASTM D329) WIPE THE EXTERIOR SURFACE PRIOR TO PRIMER
APPLICATION.
D FOR EXTERIOR SURFACES THAT DO NOT RECEIVE FINAL FINISH, PRIME
WITH ONE COAT OF MIL-PRF-85582 PRIMER.
E FOR SURFACES RECEIVING FINAL FINISH, PREPARE PER STEPS F. THROUGH I.
F PRIME SPECIFIED EXTERIOR SURFACES WITH A MIST COAT OF FMS-1058 PRIMER.
G PRIME SPECIFIED EXTERIOR SURFACES WITH ONE COAT OF FMS-3035 PRIMER
PER 366.
H PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222.
I PAINT SPECIFIED SURFACE WITH BLUE URETHANE PER 378.
J TOUCH UP AS REQUIRED PER 236, 237, AND 380.
A961 REWORK OF CURED PRIMER – WHITE URETHANE AND 16NXXXX FINISH

ALL ALUMINUM ALLOYS COVERED WITH CURED PRIMER
B PAINT INTERIOR SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
C FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER THE

AND ALUMINUM CASTINGS
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER THE
A963 PRIMER AND DARK GRAY TEFLON-URETHANE (FOR F-2 USE ONLY)
B PRIME ONE COAT SURFACES REQUIRING TEFLON-URETHANE COATING PER 202.
C PAINT SPECIFIED SURFACES WITH TWO COATS OF DARK GRAY
TEFLON-URETHANE COATING PER 259 (OR 288).
D PRIME REMAINING SURFACES TWO COATS PER 205.
A - 119

C PAINT INTERIOR SURFACES WITH EITHER WHITE ACRYLIC LACQUER

(ADHESIVE BONDED ASSEMBLY)
A CLEAN AND BRUSH CHEM FILM ALL EXPOSED SURFACES PER 134.
C PAINT INTERIOR SURFACES WITH WHITE URETHANE PER 222.
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER THE
A966 PRIMER AND 16NXXXX FINISH – PYLON

C PRIME ONE COAT REMAINING EXTERIOR SURFACES PER 535.

C PAINT PRIMED SURFACES WITH LIGHT SEMIGLOSS GRAY URETHANE
A968 16XXXX FINISH – PYLON.

C FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER
DRAWING 16N0005.
A - 120

A969 WHITE URETHANE, P5438-2 COATING, AND 16NXXXX
FINISH - ALUMINUM ALLOYS PREVIOUSLY PRIMED.
A APPLY FMS-3049 COATING TO SPECIFIED SURFACES PER 532.
B PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING
PER 222 (OR 274).
PER 254 (OR 276).
D APPLY P5438-2 RAIN EROSION RESISTANT COATING TO SPECIFIED
SURFACES PER 515.
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER THE
F TOUCH UP AS REQUIRED PER 237 AND FPS-3057.
A970 REWORK OF CURED PRIMER - WHITE URETHANE.

ALL ALUMINUM ALLOYS COVERED WITH CURED PRIMER.
B PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222.
A971 PRIMER, WHITE URETHANE AND 16NXXXX FINISH

BARE 2000 AND 7000 SERIES ALLOYS
C PAINT INTERIOR SURFACES AFTER ASSEMBLY WITH WHITE URETHANE
PER ASSEMBLY FINISH CODE.
A - 121

A972 ALUMINUM TUBING ASSEMBLIES: PRIMER AND WHITE URETHANE
COATING. PNEUMATIC, AIR DATA, HYDRAULIC, AND FUEL TUBING.
PRIME ONE COAT EXTERIOR SURFACE OF TUBE TO THE BASE OF
SLEEVE PER 272.
F PAINT SPECIFIED SURFACES WITH TWO COATS OF WHITE URETHANE
COATING PER 554.
REQUIRED PER 237 OR 242; BUT TOUCH UP ACROSS A C7551
H FOR TUBE ASSEMBLIES WITH "PERMASWAGE", "DYNATUBE",OR FLARED
INCLUDING ACROSS ASSEMBLED JOINT PER 237 OR 242.

CLAD, OR 1000, 3000, 5000, OR 6000 SERIES ALUM.
ALLOYS AND ALUMINUM ALLOY CASTINGS
C PAINT ALL SURFACES WITH LIGHT SEMIGLOSS GRAY URETHANE

C PAINT SPECIFIED INTERIOR SURFACES WITH DARK GRAY URETHANE
A - 122

A975 PRIMER AND LIGHT SEMIGLOSS GRAY URETHANE
2000 AND 7000 SERIES ALUMINUM ALLOYS - PYLONS
A ANODIZE ALL SURFACES PER 111 OR 112.
B PRIME TWO COATS EXTERIOR SURFACES PER 538 (OR 245).
C PRIME ONE COAT INTERIOR SURFACES PER 535.
D PAINT INTERIOR SURFACES WITH LIGHT SEMIGLOSS GRAY URETHANE
A - 123

SECTION D. NON-CORROSION RESISTANT STEEL ALLOYS
D100 NO FINISH REQUIRED

D104 DO NOT FINISH. DETAIL OF WELD ASSEMBLY.
D120 ALLOY STEEL - CADMIUM PLATE OR IVD ALUMINUM
HEAT TREAT STRENGTH 180 KSI OR LESS
A CADMIUM PLATE PER 120 OR IVD ALUMINUM TREAT PER 516 ALL SURFACES.
HEAT TREAT LEVEL: 180-220 KSI
HEAT TREAT STRENGTH: GREATER THAN 240 KSI
D136 REWORK OF ALLOY STEEL STANDARD PART-CADMIUM PLATE
ALLOY STEELS
A BRUSH CADMIUM PLATE SPECIFIED AREAS PER 136 OR REPLATE PER 511.
NOTE: ELEMENT 511 IS NOT TO BE USED FOR ANY STEEL WITH
TENSILE STRENGTH GREATER THAT 240 KSI.
D210 ALLOY STEEL ROUGH FORGINGS-CORROSION PREVENTIVE COMPOUND
ALL ALLOY STEEL ROUGH FORGINGS
A APPLY CORROSION PREVENTIVE COMPOUND PER 210.
D211 CORROSION PREVENTIVE SHIPPING PAPER
ALL ALLOY STEELS (FOR F2 ONLY)
HEAT TREAT LEVEL: 220-240 KSI
A CADMIUM PLATE PER 122 OR 123, OR IVD ALUMINUM TREAT PER 516
ALL SURFACES.
D402 ALLOY STEEL - (CADMIUM PLATE OR IVD ALUMINUM) PRIMER.
HEAT RANGE 180 KSI OR LESS
B PRIME ONE COAT ON AREAS SPECIFIED ON DRAWING PER 202.
D403 ALLOY STEEL - (CADMIUM PLATE OR IVD ALUMINUM)
GRAY EPOXY ENAMEL/GRAY URETHANE
HEAT TREAT RANGE - 180 KSI OR LESS
C PAINT PRIMED AREAS WITH GRAY EPOXY ENAMEL PER 211.
A - 124

HEAT TREAT RANGE: 180 KSI OR LESS
C PAINT PRIMED AREAS WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
D405 ALLOY STEEL - (CADMIUM PLATE OR IVD ALUMINUM) WHITE URETHANE
C PAINT PRIMED AREAS WITH WHITE URETHANE COATING PER 222 (OR 274).
D406 ALLOY STEEL - (CADMIUM PLATE OR IVD ALUMINUM) PRIMER
B PRIME ONE COAT ON ALL SURFACES PER 201.
HEAT TREAT RANGE: 180-220 KSI
HEAT TREAT RANGE: 180–220 KSI
C PAINT PRIMED AREAS WITH GRAY EPOXY ENAMEL OR GRAY URETHANE PER 211.
PER 213.
A - 125

WHITE URETHANE
BLACK AND ORANGE-YELLOW EPOXY ENAMEL OR URETHANE STRIPES
ALLOY STEEL 180 KSI OR LESS HEAT TREAT
C PAINT ONE COAT BLACK AND ORANGE-YELLOW EPOXY ENAMEL OR URETHANE
PER 218.
DARK GRAY URETHANE
A ELECTROLESS NICKEL PLATE SPECIFIED SURFACES PER 164 AND BAKE
PRIOR TO CADMIUM PLATING/IVD ALUMINUM.
B CADMIUM PLATE PER 154 OR IVD ALUMINUM TREAT PER 517 REMAINING
SURFACES.
D PAINT SPECIFIED PRIMED SURFACES WITH DARK GRAY URETHANE
COATING PER 257.
D413 ALLOY STEEL - (CADMIUM PLATE OR IVD ALUMINUM) EPOXY PRIMER
ALL SURFACES.
HEAT TREAT RANGE: 220 – 240 KSI
ALL SURFACES.
C PAINT PRIMED AREAS WITH GRAY EPOXY ENAMEL OR GRAY URETHANE PER 211.
A - 126

ALL SURFACES.
PER 213.
WHITE URETHANE
ALL SURFACES.
B PRIME ONE COAT ON AREAS SPECIFIED ON DRAWINGS PER 202.
C PAINT PRIMED AREAS WITH WHITE URETHANE COATING PER 222
(OR 274).
WHITE URETHANE
ALL SURFACES.
C PAINT ALL SURFACES WITH WHITE URETHANE COATING PER 223
(OR 274).
DARK GRAY URETHANE
ALLOY STEEL, HEAT TREAT RANGE: 220-240 KSI
A ELECTROLESS NICKEL PLATE SPECIFIED SURFACES PER 500.
B CADMIUM PLATE PER 154 OR IVD ALUMINUM TREAT PER 517
REMAINING SURFACES.
D PAINT SPECIFIED PRIMED SURFACES WITH DARK GRAY URETHANE
COATING PER 257.
HEAT TREAT RANGE: GREATER THAN 240 KSI
A - 127

WHITE URETHANE
D421 ALLOY STEEL - GRAY EPOXY ENAMEL/GRAY URETHANE
REWORK OF CADMIUM PLATED PARTS
A APPLY CHROMATE CONVERSION COATING TO ALL SURFACES PER 171.
B PRIME ONE COAT ON SURFACES SPECIFIED FOR GRAY EPOXY ENAMEL PER 202.
PER 211.
D422 ALLOY STEEL - BLACK EPOXY ENAMEL/BLACK URETHANE
A APPLY CHROMATE CONVERSION COATING TO ALL SURFACES PER 171.
B PRIME ONE COAT ON SURFACES SPECIFIED FOR BLACK EPOXY ENAMEL PER 202.
PER 213.
WHITE URETHANE CORROSION PREVENTIVE COMPOUND
A CADMIUM PLATE PER 155 OR IVD ALUMINUM TREAT PER 517
SPECIFIED SURFACES.
B PRIME ONE COAT ON SPECIFIED AREAS PER 202.
D APPLY CORROSION PREVENTIVE COMPOUND TO BARE SURFACES PER 250
D424 ALLOY STEEL - P6096-2 FLAT BLACK URETHANE
A CLEAN PER 144.
B PRIME ONE COAT EXPOSED SURFACES PER 202.
D425 ALLOY STEEL SPRINGS - PRIMER
ALL SURFACES.
D426 ALLOY STEEL SPRINGS - CORROSION PREVENTIVE COMPOUND
B COAT ALL SURFACES WITH COMPOUND PER 210.
A - 128

D427 ALLOY STEEL SPRINGS - NO FINISH
USED IN OIL OR GREASE MEDIA
A TEMPORARILY PROTECT BY COATING WITH COMPOUND PER 210.
B PRIOR TO INSTALLATION, DEGREASE OR SOLVENT CLEAN.
C COAT WITH OIL OR GREASE SPECIFIED ON DRAWING.
DARK GRAY URETHANE
C PAINT SPECIFIED PRIMED AREAS WITH DARK GRAY URETHANE PER 257.
B PRIME ONE COAT ON AREAS SPECIFIED ON THE DRAWING PER 202.
C PAINT PRIMED SURFACES WITH LUSTERLESS BLACK URETHANE COATING
PER 283 (OR 281).
ALL SURFACES.
PER 283 (OR 281).
DARK GRAY URETHANE
C PAINT SPECIFIED PRIMED AREAS WITH DARK GRAY URETHANE PER 257
D450 ALLOY STEEL - PRIMER AND SOLID FILM LUBRICANT.
HEAT TREAT TO 180 KSI OR LESS (FOR 10 NICKEL STEEL).
A PREPARE SURFACE AND TREAT PER 116.
B APPLY SOLID FILM LUBE TO SURFACES NOTED PER 207.
C PRIME TWO COATS TO AREAS NOTED ON DRAWING PER 205.
A - 129

D451 ALLOY STEEL - PRIMER AND SOLID FILM LUBRICANT
HEAT TREATED TO 180 - 240 KSI RANGE
D452 ALLOY STEEL - PRIMER AND SOLID FILM LUBRICANT
HEAT TREATED TO GREATER THAN 240 KSI
D453 ALLOY STEEL - SOLID FILM LUBRICANT
A PREPARE SURFACES AND TREAT PER 116.
B APPLY SOLID FILM LUBE PER 228.
HEAT TREATED TO GREATER THAN 240 KSI
A PREPARE SURFACES AND TREAT PER 118.
D455 ALLOY STEEL - PRIMER, BLACK EPOXY ENAMEL/BLACK URETHANE,
AND SOLID FILM LUBRICANT
ALLOY STEEL 240 KSI UTS HEAT TREAT
A PREPARE ALL SURFACES AND TREAT PER 118.
C PRIME TWO COATS TO REMAINING SURFACES, UNLESS OTHERWISE
SPECIFIED, PER 205.
PER 213.
A - 130

16NXXXX FINISH AND SOLID FILM LUBRICANT
HEAT TREAT LEVEL: GREATER THAN 240 KSI
A PREPARE SPECIFIED SURFACES AND TREAT PER 165.
C ON REMAINING SURFACES, VACUUM CADMIUM PLATE PER 155 OR APPLY
IVD ALUMINUM PER 517.
D PRIME ONE COAT TO SPECIFIED SURFACES PER 202.
PAINTING DRAWING.
16NXXXX FINISH AND MOLYBDENUM WEAR COATING
ALLOY STEELS HEAT TREATED GREATER THAN 220 KSI
A CLEAN, PREPARE, AND APPLY MOLYBDENUM WEAR COATING TO THE
SPECIFIED SURFACES IN THICKNESSES NOTED ON DRAWING PER 162.
B ON REMAINING SURFACES, VACUUM CADMIUM PLATE PER 155 OR
APPLY IVD ALUMINUM PER 517.
PAINTING DRAWING.
D458 ALLOY STEEL - PRIMER, LUSTERLESS BLACK
URETHANE, AND SOLID FILM LUBRICANT
HEAT TREAT RANGE: 240 KSI UTS
B APPLY SOLID FILM LUBRICANT TO SPECIFIED SURFACES IN NOTED DIMENSIONS
PER 207.
C PRIME TWO COATS ON REMAINING SURFACES, UNLESS OTHERWISE SPECIFIED,
PER 205.
D PAINT PRIMED SURFACES WITH LUSTERLESS BLACK URETHANE COATING PER 283
(OR 281).
D459 ALLOY STEEL - SOLID FILM LUBRICANT, ALL SURFACES
HEAT TREAT RANGE: 180 - 240 KSI UTS
A - 131

D460 ALLOY STEEL-(CADMIUM PLATE OR IVD ALUM) PRIMER
HT TR RNG: 220 – 240 KSI(FOR APPLICATIONS W/OUT
SIGNIFICANT SUSTAINED TENSILE OR DYNAMIC LOAD)
A CHROMIUM PLATE SPECIFIED AREA PER 143.
B CADMIUM PLATE PER 154 OR 155, OR IVD ALUMINUM TREAT PER 517
REMAINING AREA.
C PRIME ONE COAT UNTHREADED CADMIUM PLATED AREA PER 202.
D461 ALLOY STEEL-(CAD PLATE OR IVD ALUM) WHITE URETHANE
HT TR RNG: 180-200 KSI RANGE (FOR APPLICATIONS W/
OUT SIGNIFICANT SUSTAINED TENSILE OR DYNAMIC LOA
A CHROMIUM PLATE SPECIFIED AREA PER 129.
B CADMIUM PLATE PER 153 OR IVD ALUMINUM TREAT PER 517 REMAINING AREA.
C PRIME ONE COAT UNTHREADED CADMIUM PLATED AREA PER 202.
D PAINT PRIMED AREA WITH WHITE URETHANE COATING PER 222 (OR 274).
(USE ONLY FOR CRITICAL WEAR APPLICATION)
A CLEAN AND PREPARE SURFACES PER 118.
D470 ALLOY STEEL SPRINGS
A CLEAN PER FPS-3001, PARAGRAPH 3.1.4.2.
B PRIME TWO COATS ALL SURFACES PER 204.
WHITE URETHANE AND CORROSION PREVENTATIVE COMPOUND
A CADMIUM PLATE PER 154 OR IVD ALUMINUM TREAT PER 517 SPECIFIED
SURFACES.
B PRIME ONE COAT ON SPECIFIED AREAS PER 202. SPECIFIED SURFACES.
D APPLY CORROSION PROTECTIVE COMPOUND TO BARE SURFACES PER 250
PRIMER AND 16NXXXX FINISH
C FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
A - 132

PRIMER AND 16NXXXX FINISH
C FINISH EXTERIOR EXPOSED SURFACE AFTER
ASSEMBLY PER DRAWING 16N0001.
D474 ALLOY STEEL-(CAD PLATE OR IVD ALUM) AMS-C-27725
FUEL TANK COATING & WHT ACRYLIC LACQ/WHT URETHANE
HEAT TREAT RANGE - 220 KSI OR GREATER
C PRIME REMAINING SURFACES WITH ONE COAT OF PRIMER PER 202.
D476 ALLOY STEEL - (CADMIUM PLATE OR IVD ALUMINUM) AND
WHITE URETHANE
HEAT TREAT RANGE: 180 - 220 KSI
A CADMIUM PLATE PER 121 EXCEPT 10 NICKEL STEEL (HY 180), OR
IVD ALUMINUM TREAT PER 516 - ALL SURFACES.
D701 ALLOY STEEL TUBE - (CADMIUM PLATE OR IVD ALUM.)
PRIMER AND BLACK EPOXY ENAMEL/BLACK URETHANE
A CADMIUM PLATE PER 153 OR IVD ALUMINUM TREAT PER 517 TUBE OUTSIDE
AND THREADS.
B PRIME ONE COAT ON EXTERIOR SURFACES SPECIFIED FOR BLACK COLOR PER 202.
C PAINT SPECIFIED AREAS WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
D TEMPORARY CORROSION PROTECTION FOR INTERIOR OF THE TUBE
REQUIRED FOR LONG DELAYS BETWEEN CADMIUM PLATING TUBE
EXTERIOR AND PAINTING TUBE INSIDE, PER 250.
E CLEAN TUBE INSIDE, EXCEPT THREADS, PER 156.
F PRIME TWO COATS ON INTERIOR OF TUBE EXCEPT THREADS PER 205.
G TOUCH UP AS REQUIRED PER 346.
A - 133

D702 ALLOY STEEL TUBE - (CADMIUM PLATE OR IVD ALUM.)
PRIMER AND LUSTERLESS BLACK URETHANE
A CADMIUM PLATE PER 153 OR IVD ALUMINUM TREAT PER 517 TUBE OUTSIDE
AND THREADS.
B PRIME ONE COAT ON EXTERIOR SURFACES SPECIFIED FOR BLACK COLOR PER 202.
C PAINT SPECIFIED AREAS WITH LUSTERLESS BLACK URETHANE COATING
PER 283 (OR 281).
D TEMPORARY CORROSION PROTECTION FOR INTERIOR OF TUBE REQUIRED
FOR LONG DELAYS BETWEEN CADMIUM PLATING TUBE EXTERIOR AND
PAINTING TUBE INSIDE, PER 250.
E CLEAN TUBE INSIDE, EXCEPT THREADS, PER 156.
F PRIME TWO COATS ON INTERIOR OF TUBE EXCEPT THREADS PER 205.
G TOUCH UP AS REQUIRED PER 347.
D703 ALLOY STEEL - CHROMIUM PLATE AND SOLID FILM LUBRICANT.
HEAT TREAT RANGE: GREATER THAN 240 KSI.
A CHROMIUM PLATE ALL SURFACES PER 369.
C TOUCH-UP AS REQUIRED PER 315.
D704 ALLOY STEEL - SOLID FILM LUBRICANT, PRIMER, AND WHITE URETHANE.
HEAT TREAT TO 180 KSI OR LESS
B APPLY SOLID FILM LUBRICANT TO SURFACES NOTED ON DRAWING PER 207.
D PRIME ONE COAT TO AREAS NOTED ON DRAWING PER 202.
E PAINT ONE COAT-PRIMED SURFACES WITH WHITE URETHANE COATING
PER 222 (OR 274).
D705 ALLOY STEEL - SOLID FILM LUBRICANT & WHT URETHANE.
HEAT TREAT TO 180 KSI OR LESS.
B APPLY SOLID FILM LUBRICANT TO SURFACES NOTED ON DRAWING PER 207.
C PRIME ONE COAT TO AREAS NOTED ON DRAWING PER 202.
AMS-C-27725 FUEL TANK COATING
B APPLY AMS-C-27725 COATING ON ALL SURFACES PER 220.
A - 134

D707 ALLOY STEEL-SOLID FILM LUBRICANT AND WHITE
URETHANE HEAT TREAT TO 180 KSI OR LESS.
A CLEAN ALL SURFACES PER 156.
B TREAT SPECIFIED SURFACES PER 522.
C APPLY SOLID FILM LUBRICANT TO SURFACES NOTED ON DRAWING PER 207.
D PRIME ONE COAT TO AREAS NOTED ON DRAWING PER 202.
E PAINT PRIMED SURFACES WITH WHITE URETHANE COATING PER 222 (OR 274).
D708 ALLOY STEEL - (CADMIUM PLATE OR IVD ALUMINUM) WHITE URETHANE
A - 135

SECTION E. PLASTIC, GLASS REINFORCED PLASTIC, AND GRAPHITE
E100 INTERIOR NONSPECIAL COLOR AND NONFUEL AREA

PLASTIC AND GRP
A NO FINISH REQUIRED.
E103 NO FINISH REQUIRED. DETAIL OF GRAPHITE REINFORCED
PLASTIC, FIBERGLASS, OR BONDED PART.
E405 16NXXXX FINISH
PLASTIC AND GRP
A NO FINISH ON INTERIOR SURFACE.
B FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING 16N0001.
E406 WHITE URETHANE AND 16NXXXX FINISH
PLASTIC AND GRP
A CLEAN THE EXPOSED INTERIOR PER 119.
C PAINT EXPOSED INTERIOR SURFACE WITH WHITE URETHANE COATING
PER 222 (OR 274).
E411 GRAY EPOXY/URETHANE. INSTRUMENT PANELS, FLOOR,
WALLS, NONUPHOLSTERED SEAL, CONSOLES, PEDESTALS,
KNOBS, HANDLES AND LEVERS (PLASTIC AND GRP)
A CLEAN THE COCKPIT EXPOSED SURFACE PER 119.
C PAINT EXPOSED SURFACE WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
D ON NONEXPOSED SURFACE, NO FINISH REQUIRED.
E412 BLACK EPOXY ENAMEL/BLACK URETHANE
CONTROL STICK AND GRIP, INSTRUMENT CASES AND
SURFACES UNDER FIXED TRANSPARENCIES
A CLEAN THE COCKPIT EXPOSED SURFACE PER 119.
PER 213.
D ON NONEXPOSED SURFACES, NO FINISH REQUIRED.
E413 P6096-2 FLAT BLACK URETHANE
GLARESHIELD, AND PILOT'S DISPLAY UNIT. PLASTIC AND GRP
A CLEAN COCKPIT EXPOSED SURFACE PER 119.
C PAINT EXPOSED SURFACE WITH P6096-2 FLAT BLACK URETHANE
COLOR 37038, PER 217 (OR 286).
D ON NONEXPOSED SURFACE, NO FINISH REQUIRED.
A - 136

E414 WHITE URETHANE
PLASTICS
A CLEAN EXTERNAL SURFACE PER 119.
B PRIME EXTERNAL SURFACE ONE COAT PER 202.
C PAINT EXTERNAL SURFACES, WITH WHITE URETHANE COATING PER 222 (OR 274).
E415 16NXXXX FINISH
PLASTIC AND GRP
C PAINT ALL SURFACES DARK GRAY URETHANE PER 263 FOR FSD
AIRCRAFT (61: NO. 2 THRU NO. 6, 62: NO. 1 AND NO. 2).
PRODUCTION AIRCRAFT SHALL USE THE COLOR OF URETHANE COATING
SPECIFIED ON THE APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
E416 WHITE URETHANE AND 16NXXXX FINISH
FOR SOLVENT SENSITIVE INJECTION MOLDED THERMOPLASTICS
A CLEAN INTERIOR SURFACES PER 169.
B CLEAN EXTERIOR SURFACES PER 170.
C PRIME TWO COATS ALL SURFACES PER 204.
D PAINT INTERIOR SURFACES WITH WHITE URETHANE COATING PER 222.
E417 PRIMER AND 16NXXXX FINISH
GRAPHITE COMPOSITE
A REMOVE PEEL PLY ON EXTERIOR SURFACE PER 189.
B APPLY ONE COAT OF PRIMER TO EXTERIOR SURFACE PER 202.
E420 PRIMER, WHITE URETHANE, AND 16NXXXX FINISH
GRAPHITE COMPOSITE
C PAINT EXPOSED INTERIOR SURFACE WITH WHITE URETHANE COATING
PER 222 (OR 274).
GRAPHITE COMPOSITE
A REMOVE PEEL PLY ON EXTERIOR SURFACE PER 189.
B CLEAN INTERIOR SURFACES PER 119.
C PRIME ALL SURFACES ONE COAT PER 201.
E422 PRIMER
GRAPHITE OR FIBERGLASS COMPOSITE
A - 137

E423 LUSTERLESS BLACK URETHANE AND 16NXXXX FINISH
GLASS REINFORCED PLASTIC
PER 283 (OR 281).
E424 PRIMER
PLASTIC AND GRP
A CLEAN SPECIFIED SURFACES PER 119.
B PRIME SPECIFIED SURFACES PER 202.
E426 PRIMER - LAMINATED FIBERGLASS
C E426 IS DUPLICATE CODE OF E422. DO NOT USE E426 FOR NEW DESIGN.
E427 PRIMER AND WHITE URETHANE. GRP.
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222.
D TOUCH UP PER 370.
E428 PRIMER AND WHITE URETHANE – PLASTIC AND GRP
C PAINT PRIMED SURFACES WITH WHITE URETHANE COATING
PER 222 (OR 274).
E429 PRIMER, WHITE URETHANE, AND P6255 COATING – PLASTIC AND GRP
C APPLY FMS-3049 COATING TO SPECIFIED SURFACES PER 532.
D PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING PER 222.
E APPLY P6255-1 COATING, COLOR NUMBER 36173, TO SPECIFIED
SURFACES PER ENGINEERING REPORT 16ER2032.
F TOUCH UP AS REQUIRED PER ENGINEERING REPORT 16ER2032.
E430 PRIMER AND WHITE URETHANE – PLASTIC AND GRP

C PAINT ALL SURFACES WITH WHITE URETHANE COATING
PER 223 (OR 274).
A - 138

FOR SOLVENT SENSITIVE INJECTION MOLDED THERMOPLASTIC
A CLEAN SPECIFIED INTERIOR SURFACES PER 169.
B CLEAN SPECIFIED EXTERIOR SURFACES PER 170.
C PRIME TWO COATS ALL SURFACES PER 205 EXCEPT HINGE PIN HOLES.
FACES OF HINGE TANGS OPTIONAL.
D FINISH EXTERIOR EXPOSED PRIMED SURFACES AFTER ASSEMBLY
PER DRAWING 16N0001.
FOR INJECTION MOLDED P6149-1 THERMOPLASTIC
A CLEAN EXTERIOR EXPOSED SURFACE PER 119. CLEAN INTERIOR SURFACE
PER 144.
B PRIME TWO COATS ALL SURFACES PER 205 EXCEPT HINGE PIN HOLES HINGE
SLOTS.
C FINISH EXTERIOR EXPOSED PRIMED SURFACES AFTER ASSEMBLY PER DRAWING
16N0001.
E503 16NXXXX FINISH
FOR SOLVENT SENSITIVE INJECTION MOLDED THERMOPLASTIC
D FINISH EXTERIOR EXPOSED SURFACES ATER ASSEMBLY PER DRAWING 16N0001.
E504 16NXXXX FINISH
PLASTIC AND GRP
C PAINT PRIMED SURFACES PER APPLICABLE 16N0001 AIRCRAFT PAINTING
DRAWING.
FOR SOLVENT-SENSITIVE INJECTION MOLDED THERMOPLASTIC
C PRIME ALL SURFACES WITH PRIMER PER 201.
D FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER 16NXXXX.
E506 16NXXXX FINISH
GRP SURFACE
A CLEAN ALL SURFACES PER 358 (WIPE CLEAN WITH SOLVENT SUCH AS
TT-M-261 MEK, MIL-C-38736, OR FMS-2004).
C FINISH PRIMED SURFACE AFTER ASSEMBLY PER DRAWING 16NXXXX.
A - 139

E507 DARK GRAY URETHANE
PLASTIC AND GRP
C PAINT SPECIFIED SURFACES WITH TWO COATS OF DARK GRAY
E508 P6096-2 FLAT BLACK URETHANE/THERMOPLASTIC
FOR SOLVENT-SENSITIVE INJECTION MOLDED
E509 GRAY URETHANE
PLASTIC AND GRP
C PAINT SPECIFIED SURFACES WITH TWO COATS OF GRAY URETHANE
COATING PER 290.
E510 P6096-2 FLAT BLACK URETHANE FOR SOLVENT SENSITIVE
INJECTION MOLDED THERMOPLASTIC
C PAINT ALL SURFACES WITH P6096-2 FLAT BLACK URETHANE PER 266.
A - 140

SECTION F. FSX/F-2 FINISH CODES
F900 FOR FS-X/F-2 USE ONLY

A SELECT FINISH CODE FROM MITSUBISHI HEAVY INDUSTRIES (MHI) OR
FUJI HEAVY INDUSTRIES (FHI) DRAWING(S), LM(S), OR
ENGINEERING ORDER(S).
SEE MHI SPECIFICATION PFM 2701 FOR MHI FINISH CODE STEPS.
SEE FHI SPECIFICATION PFF 0021 FOR FHI FINISH CODE STEPS.
F901 FOR FS-X SSTA USE ONLY;
A OR ENGINEERING ORDER(S) (EO) FOR THE DRAWING PROVIDED BY
MITSUBISHI HEAVY INDUSTRIES (MHI) OR FUJI HEAVY INDUSTRIES
(FHI), AND SHALL BE PER PFM2791.
A - 141

SECTION N. COPPER AND NICKEL ALLOYS
N100 NO FINISH REQUIRED. (FOR NICKEL ALLOY CASTINGS

AND TUBING ASSEMBLIES & COPPER ALLOY SHIM STOCK)
A NO FINSH REQUIRED FOR CASTINGS AND TUBING ASSEMBLIES
CONTAINING LAP WELDS AND COMPONENTS THAT WOULD TRAP
PASSIVATION SOLUTIONS.
N104 DO NOT FINISH. DETAIL OF WELDED ASSEMBLY.
COPPER AND NICKEL ALLOYS
N401 COPPER ALLOY (CADMIUM PLATE OR IVD ALUMINUM)
SEE FPS-3001 FOR ELECTRICAL BONDING AND OTHER
EXCEPTIONS TO CADMIUM PLATE
SEE FPS-3001 FOR ELECTRICAL BONDING AND OTHER
EXCEPTIONS TO CADMIUM PLATE
A CADMIUM PLATE PER 159 OR 136, OR IVD ALUMINUM TREAT PER 519 SPECIFIED
SURFACES.
B FOR REWORK, CADMIUM PLATE PER 136 OR 511.
N403 NICKEL ALLOY - GRAY EPOXY ENAMEL/GRAY URETHANE
A CLEAN PER 167.
PER 211.
N404 NICKEL ALLOY - RED EPOXY ENAMEL/RED URETHANE
A CLEAN PER 167.
C PAINT PRIMED SURFACES WITH RED EPOXY ENAMEL OR RED URETHANE PER 215.
N405 COPPER ALLOY (NICKEL PLATE)
(HEAT SINKS FOR PRINTED CIRCUIT BOARDS ONLY)
A CLEAN AND PREPARE SURFACE OF COPPER ALLOY PER 180.
B EITHER ELECTROLESS NICKEL PLATE OR ELECTROLYTIC NICKEL PLATE
EXPOSED COPPER SURFACES PER 181.
C RESTORE NICKEL PLATE TO SURFACES OF DETAIL PARTS, EXCEPT
EDGES, TRIMMED ON ASSY PER 137.
A - 142

SECTION N. COPPER AND NICKEL ALLOYS
A CADMIUM PLATE PER 159 OR IVD ALUMINUM TREAT PER 519
SPECIFIED SURFACES.
C PAINT SPECIFIED SURFACES ONE COAT WITH BLACK EPOXY ENAMEL OR
N407 COPPER ALLOY (CADMIUM PLATE OR IVD ALUMINUM) WHITE URETHANE
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222.
N409 COPPER ALLOY (NICKEL PLATE)
(HEAT SINKS FOR PRINTED CIRCUIT BOARDS ONLY)
A CLEAN AND PREPARE SURFACE OF COPPER ALLOY PER 180.
B ELECTROLYTIC NICKEL PLATE EXPOSED COPPER SURFACES PER 368.
C RESTORE NICKEL PLATE TO SURFACES OF DETAIL PARTS, EXCEPT
EDGES, TRIMMED ON ASSEMBLY PER 137.
N410 REWORK OF CADMIUM PLATED STANDARD PART
NICKEL AND COPPER ALLOYS
A BRUSH CADMIUM PLATE SPECIFIED AREAS PER 136 OR REPLATE PER 511.
N601 NICKEL ALLOY - SOLID FILM LUBRICANT

ELGILOY SPRINGS AND SIMILAR PARTS
A CLEAN PER 167.
B APPLY SOLID FILM LUBRICANT PER 228 TO ALL SURFACES BY
DIPPING PER FPS-3006 TO THICKNESSES SPECIFIED ON THE DRAWING
C VERIFY SPECIFIED THICKNESS ON SAMPLES OF THE SAME MATERIAL
PROCESSED THROUGH THERMAL PROCESSING AND SOLID FILM COATING
WITH PARTS.
E
NOTE: FOR TIGHTLY COILED SPRINGS, INCOMPLETE
COVERAGE BETWEEN THE COILS SHALL NOT BE CAUSE FOR REJECTION.
N602 NICKEL ALLOY - SOLID FILM LUBRICANT
A CLEAN PER 167.
B APPLY SOLID FILM LUBRICANT TO SPECIFIED SURFACES PER 207 TO
THICKNESSES SPECIFIED ON THE DRAWING.
A - 143

SECTION R. SPECIAL FINISHES
R401 BONDED ASSY, MIXED MATERIALS - LEADING EDGE VERT. STAB., ASSY OF
A REMOVE PEEL PLY FROM EXTERIOR SURFACES OF COMPOSITE SKINS PER 189.
B CLEAN (1) THE EDGES OF THE COMPOSITE SKIN ADJACENT TO THE
LOWER CHANNEL, THE REAR SPAR AND THE UNDER TIP RIB, (2) THE
SURFACES OF THE GRAPHITE CHANNELS FORMING THE REAR SPAR AND
LOWER CHANNEL PER 119.
C BRUSH CHEMICAL FILM TREAT THE EXPOSED SURFACES OF THE
ALUMINUM CASTINGS IN THE UPPER TIP RIB AND IN THE FORWARD
END OF THE LOWER CHANNEL PER 106 (OR 300).
D PRIME ONE COAT AREAS OF PARTS CLEANED PER(A).
E PRIME TWO COATS AREAS OF PARTS CLEANED PER (B) AND (C).
F FINISH EXTERIOR EXPOSED SURFACES AND LEADING EDGE CRES CAP
AFTER ASSEMBLY PER DRAWING 16N0001.
G TOUCHUP AS REQUIRED ALUMINUM AREAS PER 235, 236, AND 242.
R402 BONDED ASSY, MIXED MATERIALS - RUDDER ASSY
B CLEAN THE EDGES OF COMPOSITE SKINS ADJACENT TO FRONT SPAR,
THE LOWER RIB AND UPPER RIB PER 119.
C BRUSH CHEMICAL FILM TREAT EXPOSED SURFACES OF ALUMINUM FRONT
SPAR, UPPER AND LOWER RIBS AND ROOT HUB PER 106 (OR 300).
D PRIME ONE COAT ALL EXPOSED SURFACES PER 202.
E PAINT THE COVE AREA INCLUDING EDGES OF COMPOSITE SKIN WITH
F PAINT THE SPECIFIED EXPOSED UPPER AND LOWER RIB SURFACE
INCLUDING EDGES OF GRAPHITE SKINS. CAP WITH DARK GRAY
URETHANE PER 257 FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6,
G PAINT THE SPECIFIED INTERIOR AND EXTERIOR ROOT HUB SURFACES
WITH DARK GRAY TEFLON-URETHANE PER 259 FOR FSD AIRCRAFT
(61: NO.2 THRU NO.6, 62: NO.1 & NO.2). PRODUCTION AIRCRAFT
SHALL USE THE COLOR OF TEFLON-URETHANE COATING SPECIFIED
ON THE APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
H FINISH EXTERIOR EXPOSED CONTOURED GRAPHITE SKINS AND
TRAILING EDGE CRES CAP AFTER ASSEMBLY PER DRAWING 16N0001.
I TOUCH UP ALUMINUM AREAS PER 237 AND 242 AND FOR THE GRAY
COLORS ON FSD AIRCRAFT PER 258 AND 260. TOUCH UP ON
PRODUCTION AIRCRAFT PER 237, 242, AND 298.
R403 BONDED ASSY, MIXED MATERIALS, GUN PORT SUPPORT
A CLEAN AND BRUSH CHEM FILM EXPOSED SURFACES OF ALUMINUM
PER 106 (OR 300).
B CLEAN EXPOSED SURFACES OF CRES PER 135.
C PRIME ONE COAT AREAS TREATED IN (A) AND CLEANED IN (B) ABOVE PER 202.
D PAINT PRIMED SURFACES WITH WHITE URETHANE PER 222 (OR 274).
E TOUCH UP ALUMINUM AREAS PER 237 AS REQUIRED.
A - 144

R404 BONDED ASSY, MIXED MATERIALS - HORIZONTAL TAIL
B CLEAN EDGES OF COMPOSITE SKINS PER 119.
C CLEAN AND BRUSH CHEM FILM TREAT EXPAND SURFACES OF ALUMINUM
TIP RIB AND TITANIUM CLOSURE RIB AND PIVOT SHAFT OUTBOARD OF
BEARING LAND PER 106 (OR 300).
D CLEAN INTERIOR OF TITANIUM PIVOT SHAFT PER 145.
E PRIME ONE COAT ON ALL SURFACES OUTBOARD OF BEARING LANDS,
EXCEPT STATIC DISCHARGER, AND INTERIOR SURFACES OF PIVOT
SHAFT EXCEPT SHEAR PIN HOLES PER 202.
F PAINT PRIMED TITANIUM CLOSURE RIB AND HUB OUTBOARD OF
BEARING LAND WITH DARK GRAY URETHANE COATING PER 257 FOR
FSD AIRCRAFT (61: NO. 2 THRU NO. 6, 62: NO. 1 AND NO. 2).
SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
G FINISH EXTERIOR EXPOSED SURFACES AND CRES LEADING AND
TRAILING EDGE CAPS AFTER ASSEMBLY PER DRAWING 16N0001.
H TOUCH UP ALUMINUM AREAS PER 235 AND 242 AS REQUIRED.
R405 BONDED ASSY, MIXED MATERIALS, VENTRAL FINS (COMPOSITE SKIN)
A CLEAN THE EDGES AND EXPOSED SURFACES OF COMPOSITE SKIN PER 119.
B BRUSH CHEMICAL FILM THE EXPOSED ALUMINUM SURFACES EXCEPT IN
THREADS OF FASTENER RECEPTACLES PER 106 (OR 300).
C PRIME TWO COATS AREAS CLEANED AND/OR CHEM FILMED IN (A) AND
(B) ABOVE EXCEPT EXTERIOR EXPOSED SURFACES, PER 205 (OR 245)
D PRIME ONE COAT EXTERIOR EXPOSED SURFACES PER 202.
F TOUCH UP ALUMINUM AREAS PER 235, 236, AND 242 AS REQUIRED.
R406 MIXED METALS - CRES AND INCONEL WELDMENTS
(NO LAP JOINTS OR BELLOWS TO TRAP ACID)
A PASSIVATE WELD ASSEMBLY PER 147.
R407 TUNGSTEN BALANCE WEIGHT - DISSIMILAR METAL PROTECTION
A CLEAN PER 183.
R408 BONDED ASSY, MIXED MATERIALS, LEADING EDGE FLAP
A CLEAN THE EXPOSED SURFACES OF GRP PER 119.
B BRUSH CHEMICAL FILM THE EXPOSED ALUMINUM SURFACES PER 106
(OR PRIME PER 300).
C PRIME ONE COAT ALL EXPOSED SURFACES OF BONDED ASSY PER 201.
D PAINT COVE AREA WITH WHITE URETHANE COATING PER 222 (OR 274)
E PRIME SPECIFIED SURFACES TWO COATS PER 205.
F PAINT INBOARD CLOSURE RIB WITH COLOR OF URETHANE COATING
SPECIFIED ON APPLICABLE 16NXXXX AIRCRAFT.
G FINISH EXTERIOR EXPOSED SURFACE AFTER ASSY PER DRAWING 16N0001.
A - 145

R409 BONDED ASSEMBLY, MIXED MATERIALS, VHF ANTENNA
A CLEAN THE EDGES AND EXPOSED SURFACES OF FIBERGLASS SKINS AND
CLOSURES PER 119.
B CLEAN AND BRUSH CHEM FILM EXPOSED SURFACES OF LEADING EDGE
AND CLOSURE RIB PER 106 (OR 300) EXCEPT THAT DIPPING IS NOT PERMITTED.
C PRIME TWO COATS SPECIFIED SURFACES OF CASTING PER 205.
F TOUCH UP ALUMINUM AREAS PER 235, 236 AND 242 AS REQUIRED.
R410 GLASS, SIGHT - LUSTERLESS BLACK
A CLEAN SPECIFIED SURFACES REQUIRING PAINT PER 144.
B PRIME ONE COAT SURFACE REQUIRING BLACK URETHANE COATING PER 202.
C PAINT PRIMED SURFACE WITH LUSTERLESS BLACK URETHANE COATING,
COLOR 37038, PER 283.
R411 LEAD - INTERIOR COMPARTMENT - WHITE
A CLEAN ALL EXPOSED SURFACES PER 180.
R412 DEPLETED URANIUM - INTERIOR COMPARTMENT - WHITE
A CLEAN AND NICKEL SULFAMATE PLATE AND CADMIUM PLATE ALL SURFACES
PER 188.
NOTE: STEP A MUST BE PERFORMED AT A U.S. ATOMIC ENERGY COMMISSION
LICENSED FACILITY.
R413 HORIZONTAL TAIL - LEADING EDGE - BONDED ASSY - MIXED MATERIALS
B CLEAN (1) THE EDGES OF THE COMPOSITE SKIN ADJACENT TO THE
LOWER CHANNEL, THE REAR SPAR AND THE UNDER TIP RIB, (2) THE
SURFACES OF THE GRAPHITE CHANNELS FORMING THE REAR SPAR AND
LOWER CHANNEL PER 119.
C BRUSH CHEM FILM INBD AND OUTBD TIP CLOSURE RIBS PER 106
(OR PRIME PER 300).
D PRIME ONE COAT PER 202 AREAS OF PARTS CLEANED PER (A), (B), AND (C).
E FINISH EXTERIOR EXPOSED SURFACES AND LEADING EDGE CRES CAP
AFTER ASSEMBLY PER DRAWING 16N0001.
F TOUCHUP AS REQUIRED ALUMINUM AREAS PER 235 AND 242.
R414 SPRAY-ON OR SHEET RUBBER PRODUCT - BONDED TO
EXTERIOR SURFACE OF AIRCRAFT
A CLEAN EXTERIOR EXPOSED SURFACES PER 170.
B PRIME ALL EXTERIOR EXPOSED SURFACES ONE COAT PER 366.
C FINISH EXPOSED EXTERIOR SURFACES PER DRAWING 16N0001.
A - 146

R415 SPRAY-ON OR SHEET RUBBER PRODUCT - BONDED TO
STRUCTURAL SURFACE OF AIRCRAFT
A CLEAN EXTERIOR EXPOSED SURFACES PER 170.
B PRIME ALL EXTERIOR EXPOSED SURFACES ONE COAT PER 366.
R416 BONDED ASSEMBLY WITH EPOXY SURFACER
A PREPARE SURFACE DESIGNATED FOR EPOXY SURFACE MATERIAL PER 119.
B APPLY FMS-0074 EPOXY SURFACER OR FMS-1104 EPOXY RESIN PER 364.
C SAND TO OBTAIN A SMOOTH SURFACE USING 240 GRIT OR FINER SAND PAPER.
D LEAK CHECK ASSEMBLY PER 365.
E BRUSH CHEM FILM THE EXPOSED ALUMINUM SURFACES PER 106.
F PRIME ONE COAT ALL EXPOSED SURFACES OF BONDED ASSEMBLY PER 201.
G PAINT INTERIOR SURFACES WITH WHITE URETHANE PER 222 (OR 274)
H FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER 16NXXXX.
I TOUCH UP AS REQUIRED PER 235, 237, AND 298.
R417 SPRAY-ON OR SHEET RUBBER PRODUCT
A CLEAN EXPOSED EXTERIOR SURFACES PER 170.
B PRIME ALL EXPOSED EXTERIOR SURFACES ONE COAT PER 366.
C PAINT PRIMED SURFACES WITH DARK GRAY URETHANE PER 263.
R419 ALUMINUM AND GRP
A CLEAN EXTERIOR AND INTERIOR SURFACES OF GRP CONES PER 119.
B PRIME ALL GRP SURFACES ONE COAT PER 201.
C PAINT EXTERIOR GRP SURFACES WITH DARK GRAY URETHANE PER 257 (OR 277).
D ANODIZE ALL SURFACES OF ALUMINUM PER 111.
E PRIME ONE COAT ALL SURFACES OF ALUMINUM PER 201.
F PAINT EXTERIOR ALUMINUM SURFACES WITH DARK GRAY URETHANE
PER 257 (OR 277).
G TOUCH UP ALUMINUM SURFACES AS REQUIRED PER 258.
H (TO BE USED ONLY WITH GD/FW MATERIALS AND PROCESSES ENGINEERING
APPROVAL).
B PAINT SPECIFIED SURFACES WITH TWO COATS OF PRIMER PER 367.
A - 147

R422 BONDED ASSY; MIXED MATERIALS - LEADING EDGE
VERTICAL STABILIZER, ASSY. OF
A CLEAN THE EXPOSED SURFACES OF GRP PER 119.
B BRUSH CHEMICAL FILM ONTO THE EXPOSED ALUMINUM SURFACES
PER 106 (OR 300).
C CLEAN THE EXPOSED SURFACES OF THE LEADING EDGE CRES CAP BY
SANDING WITH 280 OR FINER GRIT WET-OR-DRY SAND PAPER FOLLOW
BY SOLVENT CLEANING PER 135.
D APPLY ONE COAT OF WASH PRIMER TO CLEANED SURFACES OF CRES CAPS
PER 306.
E PRIME ALL EXPOSED SURFACES WITH ONE COAT OF PRIMER PER 201.
F FINISH PER 16NXXXX.
G TOUCH UP PER 235, 236, AND 242.
R423 TUNGSTEN BALANCE WEIGHT. WHITE URETHANE.
A CLEAN PER 183.
R424 MIXED MATERIALS - AME
LIGHT GRAY URETHANE AND LIGHT GRAY RAIN EROSION
RESISTANT COATING OR FMS-0025 TAPE.
C PAINT ALL EXPOSED EXTERIOR SURFACES WITH LIGHT GRAY URETHANE PER 254.
D APPLY P5438 LIGHT GRAY POLYURETHANE RAIN EROSION RESISTANT
COATING PER 515 AS FOLLOWS: PAINT ALL LEADING EDGES TO 3
+/- 0.5 INCHES AFT OF EACH LEADING EDGE OR E).
E APPLY FMS-0025 TAPE TO ALL LEADING EDGES PER FPS-0089.
R425 BERYLLIUM/BERYLLIUM OXIDE COMPOSITE
ELECTROLESS NICKEL UNDERPLATE, NICKEL PLATE AND COPPER STRIKE
A FINISH PER ENGINEERING DRAWING.
R426 SPRAY-ON RUBBER AND 16NXXXX FINISH
PYLONS AND ALTERNATE MISSION EQUIPMENT
A APPLY FMS-3049 COATING TO SPECIFIED SURFACES PER 532.
B PRIME ONE COAT SURFACES SPECIFIED FOR FMS-2026 PAINT PER 366.
C PAINT SPECIFIED SURFACES WITH FMS-2026 PAINT PER 533. COLOR TO BE
AS SPECIFIED BY DRAWING 16N0005.
E TOUCH UP AS REQUIRED PER FPS-3057 AND FPS-3076.
A - 148

R428 SPRAY-ON RUBBER AND 16NXXXX FINISH - MIXED
MATERIALS. FOR ALTERNATE MISSION EQUIPMENT.
A PREPARE SURFACES TO BE FINISHED AS SPECIFIED IN ENGINEERING
REPORT 16PR15601.
B PRIME ONE COAT ALL SURFACES TO BE FINISHED PER 535.
C APPLY FMS-3049 COATING TO SPECIFIED SURFACES PER 532.
D PRIME SURFACES SPECIFIED FOR PAINT ONE COAT PER 366.
E PAINT SPECIFIED SURFACES WITH FMS-2026 COATING PER 533.
COLOR OF PAINT SHALL BE AS SPECIFIED ON THE APPLICABLE
EQUIPMENT PAINTING DRAWING.
F TOUCH UP AS REQUIRED PER FPS-3057 AND FPS-3076.
A - 149

SECTION S. CORROSION RESISTANT STEEL ALLOYS
S100 NO FINISH REQUIRED. (FOR CRES PEEL SHIM, CASTINGS,

AND TUBING ASSEMBLIES CONTAINING LAP WELDS & FOR
COMPONENTS THAT WOULD TRAP PASSIVATION SOLUTION)
S103 DO NOT FINISH. DETAIL OF BONDED ASSEMBLY.
S104 DO NOT FINISH. DETAIL OF WELDED ASSEMBLY.
S146 ALL CRES EXCEPT CASTINGS, CRES REQUIRING COLOR
MATCH AND WELDED ASSEMBLIES WITH LAP JOINT
A CLEAN AND PASSIVATE PER 146.
NOTES: THIS PROCESS MAY NOT REMOVE HEAT TINT OR DISCOLORA-
TION RESULTING FROM THE AGING OPERATION.
S147 ALL CRES ROUGH FORGINGS AND HEAT TREATABLE CRES,
EXCEPT CASTINGS - DESCALE AND PASSIVATION
A CLEAN, CHEMICAL DESCALE AND PASSIVATE PER 147. (0.00075 IN
METAL REMOVAL PERMITTED).
S208 ALL AISI 410 OR 17-4PH ROUGH CASTINGS
A PROTECT ALL SURFACES PER 208.
S210 CASTINGS-TEMPORARY CORROSION PROTECTION
ALL AISI 410 OR 17-4PH ROUGH CASTINGS
A PROTECT ALL SURFACES PER 210.
S211 CORROSION PREVENTIVE SHIPPING PAPER
ALL CRES ALLOYS (FOR F2 ONLY)
S402 PRIMER - AISI 410 OR 17-4PH CASTING DETAILS
A CLEAN PER 135.
B PRIME ONE COAT ON SURFACES SPECIFIED ON DRAWING PER 202.
S403 GRAY EPOXY ENAMEL/GRAY URETHANE
AISI 410 OR 17-4PH CASTING DETAILS
A CLEAN PER 135.
PER 211.
A - 150

S404 BLACK EPOXY ENAMEL/BLACK URETHANE
A CLEAN PER 135.
PER 213.
S405 WHITE URETHANE - AISI 410 OR 17-4PH CASTING DETAILS
A CLEAN PER 135.
C PAINT PRIMED SURFACES WITH TWO COATS OF WHITE URETHANE COATING
PER 222 (OR 274).
S406 AMS-C-27725 FUEL TANK COATING
A CLEAN PER 135.
B APPLY AMS-C-27725 FUEL TANK COATING TO SURFACES SPECIFIED ON THE
DRAWING PER 221.
S407 WHITE URETHANE AND 16NXXXX FINISH
AISI 410 OR 17-4PH CASTING DETAILS OR PARTS PREVIOUSLY PASSIVATED
A CLEAN PER 135.
C PAINT INTERIOR EXPOSED PRIMED SURFACES WITH TWO COATS OF
S408 PRIMER AND WHITE URETHANE
A CLEAN PER 135.
C PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222 (OR 274).
S409 WHITE URETHANE
A CLEAN PER 135.
C PAINT ALL SURFACES WITH WHITE URETHANE PER 223 (OR 274).
S410 CRES TUBING
300 SERIES OR HEAT TREATABLE CRES
A PASSIVATE PER 146 (METAL REMOVAL IS NOT PERMITTED).
B (INACTIVE FOR NEW DESIGN; USE S146.)
A - 151

S411 NO FINISH
HEAT TREATABLE CRES
A PASSIVATE PER 147 (METAL REMOVAL PERMITTED).
B (INACTIVE FOR NEW DESIGN; USE S147.)
A PASSIVATE PER 146.
B PRIME ONE COAT EXPOSED SURFACE AS NOTED ON DRAWING PER 202.
C PAINT PRIMED SURFACE WITH GRAY EPOXY ENAMEL OR GRAY URETHANE
PER 211.
B PRIMED ONE COAT EXPOSED SURFACE AS NOTED ON DRAWING PER 202.
C PAINT PRIMED SURFACE WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
D TOUCH AS REQUIRED PER 323.
EXPOSED IN CREW COMPARTMENT
PER 211.
EXPOSED IN CREW COMPARTMENT
PER 213.
S416 CRES TUBING - GRAY EPOXY ENAMEL/GRAY URETHANE
B PRIME ONE COAT ON EXTERIOR SURFACE PER 203.
PER 212.
S417 CRES TUBING- BLACK EPOXY ENAMEL/BLACK URETHANE
B PRIME ONE COAT ON EXTERIOR SURFACES PER 203.
PER 214.
A - 152

S418 FLAT WHITE EPOXY ENAMEL/FLAT WHITE URETHANE
C PAINT PRIMED SURFACES WITH FLAT WHITE EPOXY ENAMEL OR FLAT WHITE
URETHANE PER 233.
S419 WHITE URETHANE. 300 SERIES OR HEAT TREATABLE
CRES, EXCEPT TUBING.
S420 CADMIUM PLATE OR IVD ALUMINUM. ALL CRES EXCEPT CASTINGS.
A PASSIVATE ALL SURFACES PER 146.
B IF CADMIUM PLATING, CLEAN AND APPLY WOOD'S NICKEL STRIKE TO
NOTED AREA PER 138. (IF APPLYING IVD ALUMINUM, SKIP THIS STEP).
C CADMIUM PLATE AREA WITH WOOD'S NICKEL STRIKE PER 175 OR IVD
ALUMINUM TREAT NOTED AREA PER 521.
S421 PRIMER AND CORROSION PREVENTIVE COMPOUND.
AISI 410 OR 17-4PH CASTING DETAILS.
A CLEAN PER 135.
C APPLY CORROSION PREVENTIVE COMPOUND TO NOTED AREA PER 250.
S422 FLAT WHITE EPOXY ENAMEL/FLAT WHITE URETHANE. 300
SERIES OR HEAT TREATABLE CRES ALREADY PASSIVATED.
A CLEAN PER 135.
C PAINT PRIMED SURFACES WITH WHITE FLAT EPOXY ENAMEL OR FLAT WHITE
URETHANE PER 233.
S423 WHITE URETHANE. 300 SERIES OR HEAT TREATABLE CRES, EXCEPT TUBING.
S424 PRIMER. 300 SERIES OR HEAT TREATABLE CRES.
A - 153

S425 16NXXXX FINISH. AISI 410 OR 17-4PH CASTING DETAILS.
A CLEAN PER 135.
FOR FSD AIRCRAFT (61: NO. 2 THRU NO. 6, 62: NO. 1 AND NO. 2)
AS SPECIFIED ON THE APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING.
S426 GRAY EPOXY ENAMEL/GRAY URETHANE AND CORROSION PREVENTIVE
COMPOUND. AISI 410 OR 17-4PH CASTING DETAILS.
A CLEAN PER 135.
B PRIME ONE COAT ON SPECIFIED AREA PER 202.
C PAINT SPECIFIED AREA WITH GRAY EPOXY ENAMEL OR GRAY URETHANE PER 211.
D APPLY ONE COAT OF MIL-C-16173 GRADE 4 CORROSION PREVENTIVE
COMPOUND ON SPECIFIED SURFACES PER 250.
S427 P6096-2 FLAT BLACK URETHANE. AISI 410 OR 17-4PH CASTING DETAILS.
A CLEAN PER 135.
S428 PRIMER. 300 SERIES AND HEAT TREATABLE CRES.
B APPLY ONE COAT WASH PRIMER ALL SURFACES PER 306.(OPTIONAL)
S429 P6096-2 FLAT BLACK URETHANE. 300 SERIES OR HEAT TREATABLE CRES.
B PRIME ONE COAT SPECIFIED SURFACE PER 202.
C PAINT PRIMED SURFACE WITH P6096-2 FLAT BLACK URETHANE PER 217 (OR 286).
S430 GRAY EPOXY ENAMEL/GRAY URETHANE.
300 SERIES OR HEAT TREATABLE CRES.
C PAINT ALL SURFACES WITH GRAY EPOXY ENAMEL PER 227.
S431 BLACK AND ORANGE-YELLOW EPOXY ENAMEL OR URETHANE
CRES CASTINGS OR SUBASSEMBLY OF 300 SERIES OR HEAT TREATABLE CRES.
A CLEAN PER 135.
C PAINT PRIMED SURFACES WITH ONE COAT OF BLACK AND
A - 154

S432 ORANGE-YELLOW EPOXY ENAMEL OR ORANGE-YELLOW URETHANE.
A PASSIVATION ALL SURFACES PER 146.
C PAINT PRIMED SURFACES ORANGE-YELLOW EPOXY ENAMEL OR
S433 CADMIUM PLATE OR IVD ALUMINUM. ALL CRES EXCEPT CASTINGS.
A IF CADMIUM PLATING, CLEAN AND APPLY WOOD'S NICKEL STRIKE TO
ALL SURFACES PER 166. (IF APPLYING IVD ALUMINUM, SKIP THIS STEP).
B CADMIUM PLATE PER 160 OR IVD ALUMINUM TREAT PER 520 ALL SURFACES.
C (INACTIVE FOR NEW DESIGN. SEE S643 FOR PREFERRED CODE.)
S434 DARK GRAY URETHANE. CRES CASTINGS.
A CLEAN PER 135.
C PAINT PRIMED SURFACES WITH DARK GRAY URETHANE COATING PER 257.
S435 PRIMER AND 16NXXXX FINISH.
B PRIME SPECIFIED INTERIOR SURFACES AND EXTERIOR SURFACES ONE COAT
PER 202.
S436 PRIMER. 300 SERIES AND HEAT TREATABLE CRES.
A CLEAN, CHEMICAL DESCALE AND PASSIVATE PER 147. (0.00075
INCH METAL REMOVAL PERMITTED).
S437 WHITE URETHANE. 300 SERIES AND HEAT TREATABLE CRES.
A CLEAN, CHEMICAL DESCALE AND PASSIVATE PER 147. (0.00075 INCH
S438 LIGHT GRAY URETHANE AND 16NXXXX FINISH. AISI 410
OR 17-4PH CASTING DETAILS OR PARTS PREVIOUSLY PASSIVATED.
A CLEAN PER 135.
C PAINT INTERIOR SPECIFIED SURFACES LIGHT GRAY URETHANE PER
254. (PAINT OVERSPRAY ONTO EXTERIOR SURFACE IS PERMISSIBLE).
A - 155

S439 BLACK EPOXY ENAMEL OR BLACK URETHANE. ALL CRES EXCEPT CASTINGS.
C PAINT ALL SURFACES WITH ONE COAT WITH BLACK EPOXY ENAMEL
OR BLACK URETHANE PER 234.
S440 BLACK EPOXY ENAMEL/BLACK URETHANE.
A CLEAN PER 135.
PER 234.
S441 PRIMER AND DARK GRAY URETHANE. 300 SERIES
AND HEAT TREATABLE CRES.
C PAINT SPECIFIED EXTERIOR SURFACES WITH DARK GRAY URETHANE
COATING PER 257.
S442 LUSTERLESS BLACK URETHANE. AISI 410 OR 17-4PH
CASTING DETAILS (CLOSE TOLERANCE FITS).
A CLEAN PER 135.
PER 283 (OR 281).
S443 LUSTERLESS BLACK URETHANE. 300 SERIES OR HEAT TREATABLE CRES.
C PAINT ALL SURFACES WITH LUSTERLESS BLACK URETHANE COATING
PER 279 (OR 281).
PER 283 (OR 281).
A - 156

S445 LUSTERLESS GRAY URETHANE. 300 SERIES OR HEAT TREATABLE CRES.
C PAINT ALL SURFACES WITH LUSTERLESS GRAY URETHANE COATING
PER 278 (OR 280).
S446 LUSTERLESS GRAY URETHANE. 300 SERIES OR HEAT TREATABLE CRES.
B PRIME ONE COAT SPECIFIED SURFACE PER 202.
C PAINT PRIMED SURFACE WITH LUSTERLESS GRAY URETHANE COATING
PER 282 (OR 280).
S447 LUSTERLESS BLACK URETHANE. AISI 410 OR 17-4PH CASTING DETAILS.
A CLEAN PER 135.
(OR 281).
S448 PRIMER AND LUSTERLESS GRAY URETHANE.
A CLEAN PER 135.
C PAINT ONE COAT SPECIFIED SURFACES WITH LUSTERLESS GRAY
S449 DARK GRAY URETHANE. 300 SERIES AND HEAT TREATABLE CRES.
C PAINT PRIMED SURFACES WITH DARK GRAY URETHANE COATING PER 257.
S450 WHITE ACRYLIC LACQUER/WHITE URETHANE. 300 SERIES
OR HEAT TREATABLE CRES, EXCEPT TUBING.
S451 WHITE ACRYLIC LACQUER/WHITE URETHANE. HEAT
TREATABLE CRES REQUIRING DESCALE.
B PRIME ALL SURFACES ONE PER 201.
A - 157

S452 DARK GRAY URETHANE AND 16NXXXX FINISH.
300 SERIES AND HEAT TREATABLE CRES.
A CLEAN, CHEMICAL DESCALE AND PASSIVATE PER 147.
PER 257 (OR 277).
S453 DARK GRAY URETHANE AND 16NXXXX FINISH - PYLONS. CRES CASTINGS.
A CLEAN PER 135.
PER 257.
S454 ORANGE-YELLOW EPOXY ENAMEL/ORANGE-YELLOW URETHANE
AISI 410 OR 17-4PH CASTINGS. (CLOSE TOLERANCE FITS).
A CLEAN PER 135.
C PAINT PRIMED SURFACES WITH ORANGE-YELLOW EPOXY ENAMEL OR
C PAINT ALL SURFACES WITH LUSTERLESS BLACK URETHANE COATING
PER 279 (OR 281).
S456 PRIMER. AISI 410 OR 17-4PH CASTINGS.
A CLEAN PER 135.
S457 PRIMER AND WHITE URETHANE. 300 SERIES OR HEAT TREATABLE CRES.
C PAINT SPECIFIED SURFACES WITH URETHANE COATING PER 222 (OR 274)
S458 PRIMER AND BLUE URETHANE.
A CLEAN PER 135.
C PAINT SPECIFIED SURFACES WITH BLUE URETHANE PER 378 (OR 381).
A - 158

S459 BLUE URETHANE. CRES, EXCEPT TUBING.
C PAINT PRIMED SURFACES WITH BLUE URETHANE COATING PER 378 (OR 381).
S460 PRIMER AND BLUE URETHANE. 300 SERIES OR HEAT TREATABLE CRES.
C PAINT SPECIFIED SURFACES WITH BLUE URETHANE COATING PER 378 (OR 381).
S461 AMS-C-27725 FUEL TANK COATING, WHITE URETHANE, AND
16NXXXX FINISH. AISI 410 OR 17-4PH CASTINGS AND
PARTS PREVIOUSLY PASSIVATED.
A CLEAN PER 135.
B APPLY AMS-C-27725 FUEL TANK COATING TO SPECIFIED SURFACES PER 221.
C PRIME ONE COAT SURFACES REQUIRING PAINT PER 202.
E PAINT EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER THE APPLICABLE
16NXXXX PAINTING DRAWING.
S462 WHITE URETHANE. 300 SERIES OR HEAT TREATABLE
CRES, EXCEPT TUBING. FOR PARTS PREVIOUSLY PASSIVATED.
A CLEAN PER 135.
S463 AMS-C-27725 FUEL TANK COATING, WHITE URETHANE,
AND 16NXXXX FINISH. AISI 410 OR 17-4PH CASTING DETAILS.
A CLEAN PER 135.
B APPLY AMS-C-27725 FUEL TANK COATING TO SPECIFIED SURFACES PER 221.
D PAINT SPECIFIED SURFACES WITH WHITE URETHANE COATING
PER 222 (OR 274).
E FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER
THE APPLICABLE 16NXXXX PAINTING DRAWING.
S464 LIGHT GRAY URETHANE AND 16NXXXX FINISH.

A CLEAN, CHEMICAL DESCALE AND PASSIVATE PER 147.
C PAINT SPECIFIED SURFACES WITH LIGHT GRAY URETHANE PER 544 (OR 547).
A - 159

S601 SOLID FILM LUBRICANT. ALL CRES EXCEPT CASTINGS.
A PASSIVATE PART PER 146.
B CLEAN NOTED THREADS PER 144.
C ON NOTED THREADS APPLY SOLID FILM LUBRICANT PER 230.
S602 SOLID FILM LUBRICANT. HEAT TREATED CRES, EXCEPT
440C AND CASTINGS.
B TO SPECIFIED AREA APPLY SOLID FILM LUBRICANT PER 207.
S603 SOLID FILM LUBRICANT. HEAT TREATED CRES, EXCEPT
440C AND CASTINGS.
A PHOSPHATIZE ALL SURFACES PER 148.
S604 WHITE URETHANE AND SOLID FILM LUBRICANT.
300 SERIES CRES ONLY.
B APPLY SOLID FILM LUBRICANT TO SPECIFIED SURFACE IN NOTED
THICKNESSES OR DIMENSION PER 207.
C PRIME ONE COAT ON REMAINING SURFACES PER 202.
HEAT TREATABLE CRES, EXCEPT CASTINGS.
B APPLY SOLID FILM LUBRICANT TO SPECIFIED SURFACES IN NOTED
THICKNESSES OR DIMENSIONS PER 207.
C PRIME ONE COAT ON REMAINING SURFACES PER 202.
S606 SOLID FILM LUBRICANT. WROUGHT CRES.
A PASSIVATE EXCEPT FOR CADMIUM PLATE/IVD ALUM AREA PER 177.
B IF CADMIUM PLATING, APPLY WOOD'S NICKEL STRIKE WHERE SPECI-
FIED PER 138. (IF APPLYING IVD ALUMINUM, SKIP THIS STEP).
C CADMIUM PLATE SURFACES WHICH RECEIVED THE WOOD'S NICKEL
STRIKE PER 161 OR IVD ALUMINUM TREAT SPECIFIED SURFACES PER 521.
D CLEAN NOTED THREADS PER 144.
E ON NOTED THREADS APPLY SOLID FILM LUBRICANT PER 230.
A - 160

S607 BLACK EPOXY ENAMEL/BLACK URETHANE AND SOLID FILM LUBRICANT.
C PRIME ONE COAT ON REMAINING SURFACES, UNLESS OTHERWISE
SPECIFIED PER 202.
PER 213.
S608 SOLID FILM LUBRICANT. HEAT TREATABLE CRES.
A CLEAN NITRIDED SURFACES BY REMOVING WHITE LAYER BY LIGHT GRIT BLAST.
B VAPOR DEGREASE.
C APPLY SOLID FILM LUBE TO SPECIFIED SURFACES PER 207 (PER THE
RINSE, DRY, AND LUBRICANT APPLICATION STEPS OF FPS-3006, CLASS VIII).
S609 GRAY EPOXY ENAMEL/GRAY URETHANE AND SOLID FILM LUBRICANT.
THICKNESS OR DIMENSIONS PER 207.
C PRIME ONE COAT THE REMAINING SURFACES, UNLESS OTHERWISE
SPECIFIED, PER 202.
PER 211.
S610 SOLID FILM LUBRICANT. CRES CASTINGS; USE FOR
PARTS WITH PRESS FIT APPLICATIONS.
S611 ORANGE-YELLOW EPOXY ENAMEL/ORANGE-YELLOW URETHANE
AND SOLID FILM LUBRICANT. CRES CASTINGS.
B APPLY SOLID FILM LUBE TO SPECIFIED SURFACES IN NOTED
C PRIME ONE COAT REMAINING SPECIFIED SURFACES IN PER 202.
D PAINT PRIMED SURFACES ONE COAT OF ORANGE-YELLOW ENAMEL OR
S612 SOLID FILM LUBRICANT. 300 SERIES CRES ONLY.
A - 161

300 SERIES CRES.
THICKNESS OR DIMENSION PER 207.
C PRIME ONE COAT THE REMAINING SURFACES, UNLESS OTHERWISE
SPECIFIED, PER 202.
PER 211.
300 SERIES CRES AND PRECIPITATION HARDENABLE CRES.
PER 211.
D ON THREADS UNLESS OTHERWISE NOTED, APPLY SOLID FILM LUBRICANT PER 230.
S615 SOLID FILM LUBRICANT. 300 SERIES CRES ONLY.
S616 PRIMER AND SOLID FILM LUBRICANT. CRES CASTINGS.
B APPLY SOLID FILM LUBE TO SPECIFIED SURFACES IN NOTED
C PRIME ONE COAT REMAINING SPECIFIED AREAS PER 202.
S617 SOLID FILM LUBRICANT. 300 SERIES ONLY.
A DESCALE AND PASSIVATE PER 147.
S618 SOLID FILM LUBRICANT. CRES CASTINGS.
S619 P6096-2 FLAT BLACK URETHANE AND SOLID FILM LUBRICANT.
HEAT TREATABLE CRES, EXCEPT 440C.
B APPLY SOLID FILM LUBE TO SPECIFIED SURFACES IN THICKNESSES
OR DIMENSIONS AS NOTED PER 207.
C PRIME SPECIFIED AREAS ONE COAT PER 202.
A - 162

S620 LUSTERLESS BLACK URETHANE AND SOLID FILM LUBRICANT.
THICKNESS OR DIMENSIONS PER 207.
C PRIME ONE COAT ON REMAINING SURFACES, UNLESS OTHERWISE SPECIFIED,
PER 202.
D PAINT SPECIFIED PRIMED SURFACES WITH LUSTERLESS BLACK
S621 16NXXXX FINISH SOLID FILM LUBRICANT, AND CORROSION
PREVENTATIVE COMPOUND. AISI 410 OR 17-4PH
CASTINGS OR WELDMENTS INCLUDING CASTINGS.
A CLEAN PER 135
B PRIME ONE COAT SURFACES SPECIFIED ON DRAWING PER 202.
C ON NOTED THREADS APPLY SOLID FILM LUBRICANT PER 230.
D APPLY CORROSION PREVENTATIVE COMPOUND TO NOTED AREAS PER 250.
E FINISH EXTERIOR EXPOSED PRIMED SURFACES AFTER ASSEMBLY PER DRAWING
16N0001.
F TOUCH UP AS REQUIRED PER 329.
CRES CASTINGS AND WELDED ASSEMBLIES.
PER 211.
D APPLY SOLID FILM LUBRICANT TO NOTED THREADS PER 230.
S623 WHITE URETHANE AND 16NXXXX FINISH. 300 SERIES
OR HEAT TREATABLE CRES, EXCEPT TUBING.
S624 ORANGE-YELLOW EPOXY ENAMEL/ORANGE-YELOW URETHANE AND
SOLID FILM LUBRICANT. HEAT TREATABLE CRES, EXCEPT CASTINGS.
B APPLY SOLID FILM LUBE TO SPECIFIED SURFACES IN THICKNESSES
C PRIME SPECIFIED AREA ONE COAT PER 202.
D PAINT PRIMED SURFACES ONE COAT OF ORANGE-YELLOW EPOXY ENAMEL OR
E TOUCH AS REQUIRED PER 332 AND 340.
A - 163

S625 SOLID FILM LUBRICANT. CRES CASTINGS.
S626 PRIMER AND SOLID FILM LUBRICANT.
300 SERIES OR HEAT TREATABLE CRES, EXCEPT CASTINGS
C APPLY SOLID FILM LUBE ON NOTED THREADS PER 230.
S627 SILVER PLATE. HEAT TREATABLE CRES, EXCEPT CASTINGS.
A CLEAN AND PASSIVATE SPECIFIED SURFACES PER 177.
B CLEAN, NICKEL STRIKE, AND SILVER STRIKE SPECIFIED SURFACES PER 184.
C CLEAN, NICKEL STRIKE, SILVER STRIKE, AND SILVER PLATE
SPECIFIED SURFACES PER 185.
S628 GRAY URETHANE, 16NXXXX FINISH, AND SOLID FILM
LUBRICANT. CRES CASTINGS.
A CLEAN PER 135.
D PAINT SPECIFIED INTERIOR SURFACES WITH GRAY URETHANE, COLOR 36270,
PER 290 (OR 292).
F TOUCH UP AS REQUIRED PER 353 OR 340.
S629 MEDIUM GRAY TEFLON-URETHANE. 300 SERIES OR HEAT
TREATABLE CRES, EXCEPT CASTINGS.
C PAINT ALL SURFACES WITH MEDIUM GRAY TEFLON-URETHANE, COLOR 36270,
PER 301.
S631 DARK GRAY URETHANE. CRES CASTINGS.
A CLEAN PER 135.
C PAINT ALL PRIMED SURFACES WITH DARK GRAY URETHANE COATING PER 263.
D TOUCH UP PER 333.
S632 SOLID FILM LUBRICANT AND CHROMIUM PLATE.
B GRIT BLAST PER 183. MASK ANY THREADS ON PART.
C ON SPECIFIED AREAS APPLY WOOD'S NICKEL STRIKE PER 138.
D CHROME PLATE SPECIFIED SURFACES PER 129.
E APPLY SOLID FILM LUBRICANT TO ALL SURFACES PER 228.
A - 164

S633 CHROME PLATE. 300 SERIES OR HEAT TREATABLE CRES.
B GRIT BLAST PER 183. MASK ONLY THREADS ON PART.
C ON SPECIFIED PARTS APPLY WOOD'S NICKEL STRIKE PER 138.
S634 CHROME PLATE. 300 SERIES OR HEAT TREATABLE CRES.
B GRIT BLAST PER 180.
C APPLY WOOD'S NICKEL STRIKE TO ALL SURFACES PER 166.
D CHROME PLATE ALL SURFACES PER 369.
S635 AMS-C-27725 FUEL TANK COATING. 300 SERIES OR
HEAT TREATABLE CRES (EXCEPT CASTINGS).
B APPLY AMS-C-27725 COATING TO ALL SURFACES PER 220.
C TOUCH UP AS PER 325.
S636 AERODYNAMIC SEALS.
C APPLY ONE COAT OF MIL-C-8514 WASH PRIMER TO REMAINING SURFACES PER 306.
D PRIME ONE COAT INTERIOR SURFACES PER 202.
E PAINT PRIMED SURFACES WITH WHITE URETHANE PER 222 (OR 274).
F PRIME REMAINING EXTERIOR EXPOSED SURFACES ONE COAT PER 202.
G FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER 16NXXXX.
S637 AERODYNAMIC SEALS.
B PASSIVATE ALL SURFACES PER 146.
C APPLY SOLID FILM LUBRICANT TO SPECIFIED SURFACES PER 207;
HOWEVER, DO NOT REPEAT GRIT BLAST AND PASSIVATION PROCEDURES
(PRIOR TO SOLID FILM LUBRICANT APPLICATION) IF THESE OPER-
ATIONS HAVE ALREADY BEEN PERFORMED.
D APPLY ONE COAT OF MIL-C-8514 WASH PRIMER TO REMAINING SURFACES PER 306.
E PRIME INTERIOR SURFACES WITH ONE COAT OF PRIMER PER 202.
F PAINT PRIMED INTERIOR SURFACES WITH WHITE URETHANE PER 222 (OR 274).
G PRIME REMAINING EXTERIOR EXPOSED SURFACES WITH ONE COAT OF PRIMER
PER 202.
H FINISH EXTERIOR EXPOSED SURFACES AFTER ASSEMBLY PER 16NXXXX.
I TOUCH UP AS REQUIRED PER 321, 324, 329, AND 340.
A - 165

S638 AMS-C-27725 FUEL TANK COATING AND WHITE ACRYLIC
LACQUER/WHITE URETHANE. 300 SERIES OR HEAT TREATABLE CRES.
B APPLY AMS-C-27725 FUEL TANK COATING ON SPECIFIED FAYING
S639 WHITE URETHANE AND 16NXXXX FINISH. 300 SERIES OR
HEAT TREATABLE CRES (EXCEPT TUBING).
D FINISH EXTERIOR SURFACES PER THE APPLICABLE 16NXXXX AIRCRAFT
PAINTING DRAWING.
E TOUCH AS REQUIRED PER 324.
B APPLY MIL-C-8514 WASH PRIMER TO SPECIFIED SURFACES PER 306.
C PRIME SPECIFIED SURFACES WITH ONE COAT OF PRIMER PER 202.
D PAINT PRIMED SURFACES WITH DARK GRAY URETHANE COATING PER 257.
B APPLY MIL-C-8514 WASH PRIMER TO ALL SURFACES PER 316.
C PRIME ALL SURFACES WITH ONE COAT OF PRIMER PER 201.
D PAINT PRIMED SURFACES WITH TWO COATS OF DARK GRAY URETHANE COATING
PER 263.
E TOUCH UP PER 333.
S642 LIGHT GRAY URETHANE AND 16NXXXX FINISH. AISI 410
OR 17-4PH CASTING DETAILS OR PARTS PREVIOUSLY PASSIVATED.
A CLEAN PER 135.
C PAINT INTERIOR SPECIFIED SURFACES LIGHT GRAY URETHANE PER
254. (PAINT OVERSPRAY ONTO EXTERIOR SURFACES IS PERMISSIBLE)
16NXXXX.
S643 CADMIUM PLATE OR IVD ALUMINUM.
A IF CADMIUM PLATING, CLEAN AND APPLY WOOD'S NICKEL STRIKE TO
ALL SURFACES PER 166. (IF APPLYING IVD ALUMINUM, SKIP THIS STEP.
B CADMIUM PLATE PER 160 OR IVD ALUMINUM TREAT PER 520 ALL SURFACES.
A - 166

S644 CADMIUM PLATE OR IVD ALUMINUM, AND CHROME PLATE.
A GRIT BLAST ALL SURFACES PER 180.
B PASSIVATE ALL SURFACES PER 146.
C APPLY WOOD'S NICKEL STRIKE TO ALL SURFACES PER 166.
E CADMIUM PLATE PER 161 OR IVD ALUMINUM TREAT PER 521 SPECIFIED
SURFACES.
S645 WHITE URETHANE.
B APPLY ONE COAT OF PRIMER TO SPECIFIED SURFACES PER 202.
C PAINT SPECIFIED SURFACES WITH MIL-C-83286 OR MIL-C-85285 URETHANE
COATING; WHITE COLOR NO. 17875 OR COLOR NO. 17925 PER 222 (OR 274).
S646 FMS-3014 FORM 2 ADHESIVE PRIMER
300 SERIES OR HEAT TREATABLE CRES (EXCEPT CASTINGS)
B APPLY FMS-3014 FORM 2 TO ALL SURFACES PER 400.
C TOUCH UP PER 523 (OR 524 AS APPLICABLE).
S647 CADMIUM PLATE OR IVD ALUMINUM, AND ELECTROLESS
NICKEL PLATE. 300 SERIES OR HEAT TREATABLE CRES.
A CLEAN AND APPLY WOOD'S NICKEL STRIKE TO ALL SURFACES PER 166.
B ELECTROLESS NICKEL PLATE ALL SURFACES PER 125.
C CADMIUM PLATE PER 161 OR IVD ALUMINUM TREAT PER 521
SPECIFIED SURFACES.
S648 SOLID FILM LUBRICANT, LIGHT GRAY URETHANE AND 16N0001 FINISH.
AISI 410 OR 17-4PH CASTING DETAILS OR PARTS PREVIOUSLY PASSIVATED.
A CLEAN PER 135.
C APPLY ONE COAT OF WASH PRIMER TO SPECIFIED SURFACES PER 306.
D PRIME WASH-PRIMED AREAS PER 202.
E PAINT SPECIFIED AREAS WITH LIGHT GRAY URETHANE PER 254.
F FINISH REMAINING SURFACES AFTER ASSEMBLY PER DRAWING 16N0001
G TOUCH UP AS REQUIRED PER 340 AND 348.
S649 SOLID FILM LUBRICANT AND MIL-C-85054
CRES CASTINGS.
C APPLY MIL-C-85054 TO SPECIFIED SURFACES PER 505.
A - 167

S650 RED EPOXY ENAMEL/RED URETHANE AND 16N0001 FINISH
C APPLY RED EPOXY ENAMEL OR RED URETHANE TO SPECIFIED SURFACES PER 215.
D FINISH EXTERIOR EXPOSED SURFACES PER 16N0001.
E TOUCH-UP AS REQUIRED 321 AND 334.
S651 RED EPOXY ENAMEL/RED URETHANE, SOLID FILM LUBRICANT AND
16NXXXX FINISH – PYLON. AISI 410 OR 17-4PH CASTING DETAILS.
D PAINT SPECIFIED SURFACES WITH ONE COAT OF RED EPOXY ENAMEL
PER 215 (OR APPLY RED URETHANE PER 512).
E FINISH EXTERIOR SURFACES PER DRAWING 16N0005.
F TOUCH UP AS REQUIRED PER 329, 340, AND 508 (OR 513).
16NXXXX FINISH - PYLON. 300 SERIES OR HEAT TREATABLE CRES.
D PAINT SPECIFIED SURFACES WITH ONE COAT OF RED EPOXY ENAMEL OR
RED URETHANE PER 215.
S654 SOLID FILM LUBRICANT
ALL CRES EXCEPT CASTINGS
B APPLY SOLID FLIM LUBRICANT PER 510.
NOTE: THIS CODE IS INTENDED FOR PREVIOUSLY PASSIVATED
VENDOR PARTS. DO NOT USE WITHOUT MATERIALS AND
PROCESSES ENGINEERING APPROVAL.
A - 168

300 SERIES CRES AND PRECIPITATION HARDENABLE CRES
PER 213.
D ON THREADS, UNLESS OTHERWISE NOTED, APPLY SOLID FILM
LUBRICANT PER 230.
E TOUCH UP AS REQURED PER 323.
16NXXXX FINISH – PYLON. 300 SERIES OR HEAT TREATABLE CRES
D PAINT SPECIFIED SURFACES WITH ONE COAT OF RED EPOXY ENAMEL OR RED
URETHANE PER 215.
CRES CASTINGS AND WELDED ASSEMBLIES.
PER 213.
D APPLY SOLID FILM LUBRICANT TO NOTED THREADS PER 230.
S658 PRIMER AND 16NXXXX FINISH.
S659 DARK GRAY URETHANE AND 16NXXXX FINISH OVER IVD ALUMINUM - PYLONS.
B IVD ALUMINUM TREAT ALL SURFACES PER 520.
D PAINT SPECIFIED INTERIOR SURFACES WITH GRAY COLOR 36270
F TOUCHUP AS REQUIRED PER 353.
A - 169

S660 DARK GRAY URETHANE FINISH OVER IVD ALUMINUM-PYLONS
D PAINT PRIMED SURFACES WITH GRAY COLOR 36270 URETHANE COATING
PER 289 (OR 292).
E TOUCHUP AS REQUIRED PER 353.
S661 SOLID FILM LUBRICANT AND CADMIUM PLATE/IVD ALUM. WROUGHT CRES.
A PASSIVATE EXCEPT FOR CADMIUM PLATE/IVD ALUM AREA PER 177.
B IF CADMIUM PLATING, APPLY WOOD’S NICKEL STRIKE WHERE SPECIFIED
PER 138. (IF APPLYING IVD ALUMINUM, SKIP THIS STEP.)
C CADMIUM PLATE SURFACES WHICH RECEIVED THE WOOD’S NICKEL STRIKE
PER 161 OR IVD ALUMINUM TREAT SPECIFIED SURFACES PER 521.
D PREPARE AREA TO RECEIVE SOLID FILM LUBRICANT PER 148.
E APPLY SOLID FILM LUBRICANT TO PREPARED AREA PER 228.
S662 SOLID FILM LUBRICANT AND CHROMIUM PLATE.

B GRIT BLAST PER 183. MASK AREAS NOT TO BE CHROME PLATED.
C ON AREAS TO BE PLATED, APPLY WOOD’S NICKEL STRIKE PER 138.
E APPLY SOLID FILM LUBRICANT TO SPECIFIED SURFACES PER 228.
S663 LIGHT GRAY SEMIGLOSS GRAY URETHANE AND 16NXXX FINISH-

PYLONS. 300 SERIES AND HEAT TREATABLE CRES.
D PAINT INTERIOR SURFACES WITH TWO COATS OF LIGHT SEMIGLOSS
GRAY URETHANE COATING PER 544.
A - 170

S664 LIGHT SEMIGLOSS GRAY URETHANE AND 16NXXXX FINISH -
PYLONS. CRES CASTINGS.
A CLEAN PER 135.
C PAINT SPECIFIED INTERIOR SURFACES WITH LIGHT SEMIGLOSS GRAY
S665 DARK GRAY URETHANE AND 16NXXX FINISH - PYLONS.

D PAINT INTERIOR SURFACES WITH TWO COATS OF DARK GRAY
S666 DARK GRAY URETHANE AND 16NXXXX FINISH - PYLONS.

CRES CASTINGS.
A CLEAN PER 135.
COATING PER 257.
S667 DARK GRAY URETHANE AND 16NXXXX FINISH OVER IVD

ALUMINUM - PYLONS. 300 SERIES OR HEAT TREATABLE CRES.
D PAINT SPECIFIED INTERIOR SURFACES WITH GRAY COLOR 26493
SEMIGLOSS URETHANE COATING PER 544 (OR 542).
F TOUCHUP AS REQUIRED PER 555.
A - 171

S668 DARK GRAY URETHANE FINISH OVER IVD ALUMINUM -
PYLONS. 300 SERIES OR HEAT TREATABLE CRES.
D PAINT PRIMED SURFACES WITH GRAY COLOR 26493 SEMIGLOSS
E TOUCHUP AS REQUIRED PER 555.
S701 LIGHT GRAY URETHANE AND PRIMER (FOR FS-X PARTS)

AISI 410 OR 17-4PH CASTING DETAILS OR PARTS PREVIOUSLY PASSIVATED.
A CLEAN PER 135.
C PAINT SPECIFIED SURFACES WITH LIGHT GRAY URETHANE PER 254
S702 WHITE URETHANE. 300 SERIES OR HEAT TREATABLE CRES,
EXCEPT TUBING
B PRIME ONE COAT ALL SURFACES EXCEPT HOLES PER 202.
C PAINT PRIMED SURFACES WITH WHITE URETHANE COATING PER 222.
S703 PRIMER AND CORROSION PREVENTIVE COMPOUND.
C APPLY CORROSION PREVENTIVE COMPOUND TO NOTED AREA PER 250.
S704 WHITE URETHANE AND 16NXXXX FINISH.
HEAT TREATABLE CRES (EXCEPT TUBING).
D FINISH EXTERIOR SURFACES PER THE APPLICABLE 16NXXXX AIRCRAFT
S705 FMS-3014 FORM 2 ADHESIVE PRIMER
B APPLY FMS-3014 FORM 2 TO SPECIFIED SURFACES PER 403.
C TOUCH UP AS REQUIRE PER 523 (OR 524 AS APPLICABLE)
A - 172

S706 WHITE URETHANE AND 16NXXXX FINISH
B PRIME ALL SURFACES ONE PER 201.
C PAINT INTERIOR EXPOSED SURFACES WITH TWO COATS OF
S707 BLUE URETHANE. 300 SERIES OR HEAT TREATABLE CRES, EXEPT TUBING
B PRIME ONE COAT ALL SURFACES EXCEPT HOLES PER 202.
C PAINT PRIMED SURFACES WITH BLUE URETHANE COATING PER 378.
A - 173

SECTION T. TITANIUM AND TITANIUM ALLOYS
T100 NO FINISH REQUIRED. TITANIUM AND TITANIUM ALLOYS

T103 DO NOT FINISH. DETAIL OF BONDED ASSEMBLY.
T104 DO NOT FINISH. DETAIL OF WELDED ASSEMBLY.
TITANIUM AND TITANIUM ALLOYS.
T151 FLUORIDE PHOSPHATE TREATMENT. TITANIUM AND
TITANIUM ALLOYS (DO NOT USE ON WELDED ASSEMBLIES
CONTAINING LAP WELDS WHICH WOULD ENTRAP SOLUTIONS)
A CLEAN AND APPLY CONVERSION TREATMENT TO ALL SURFACES PER 151.
T187 FLUORIDE PHOSPHATE TREATMENT. TITANIUM AND
TITANIUM ALLOYS (DO NOT USE ON WELDED ASSEMBLIES
CONTAINING LAP WELDS WHICH WOULD ENTRAP SOLUTIONS)
A CLEAN AND APPLY CONVERSION TREATMENT TO SPECIFIED SURFACES PER 187.
T401 ANTIGALL OR WEAR SURFACE TREATMENT.

A APPLY CONVERSION TREATMENT TO ALL SURFACES PER 151.
B (INACTIVE FOR NEW DESIGN, SEE T151 FOR PREFERRED CODE.)
T402 WHITE URETHANE.
A CLEAN PER 145.
B PRIME EXPOSED SURFACES ONE COAT PER 202.
C PAINT PRIMED SURFACE WITH WHITE URETHANE COATING PER 222 (OR 274).
T403 FLUORIDE PHOSPHATE TREATMENT AND WHITE URETHANE.
DO NOT USE ON WELDED ASSEMBLIES CONTAINING LAP
WELDS WHICH WOULD ENTRAP SOLUTIONS.
B PRIME ONE COAT SURFACES SPECIFIED FOR WHITE COLOR PER 202.
T404 PRIMER AND 16NXXXX FINISH. ALL SURFACES.
A CLEAN AND APPLY CONVERSION TREATMENT TO ALL SURFACES PER
151 OR CLEAN AND ABRADE ALL SURFACES PER 183.
T405 PRIMER. DISSIMILAR METAL PROTECTION.
A CLEAN PER 145.
A - 174

T406 PRIMER AND 16NXXXX FINISH.
ALL TITANIUM ALLOYS.
A CLEAN AND APPLY CONVERSION TREATMENT TO ALL SURFACES PER 151
T407 PRIMER AND BLACK EPOXY ENAMEL/BLACK URETHANE.
ALL TITANIUM ALLOYS.
A CLEAN PER 145.
C PAINT SPECIFIED SURFACES WITH BLACK EPOXY ENAMEL OR BLACK URETHANE
PER 213.
T408 PRIMER AND DARK GRAY URETHANE. TITANIUM ALLOYS.
C PAINT PRIMED SURACES WITH DARK GRAY URETHANE COATING PER 527.
T409 PRIMER AND DARK GRAY URETHANE. TITANIUM ALLOYS.
C PAINT ALL SURACES WITH DARK GRAY URETHANE COATING PER 529.
T410 WHITE ACRYLIC LACQUER/WHITE URETHANE AND 16NXXXX FINISH

TITANIUM ALLOYS.
A CLEAN PER 145.
C PAINT INTERIOR SURFACES WITH EITHER WHIT ACRYLIC LACQUER OR
T411 WHITE URETHANE AND 16NXXXX FINISH

TITANIUM ALLOYS
OR CLEAN AND ABRADE ALL SURFACES PER 183.
A - 175

T412 FLUORIDE PHOSPHATE TREATMENT AND WHITE URETHANE.
DO NOT USE ON WELDED ASSEMBLIES CONTAINING LAP
WELDS WHICH WOULD ENTRAP SOLUTIONS.
T450 SOLID FILM LUBRICANT.
(FOR ASSEMBLIES CONTAINING LAP WELDS
WHICH WOULD ENTRAP SOLUTIONS.)
A PREPARE SURFACES SPECIFIED PER 151.
B APPLY SOLID FILM LUBE TO SURFACES IN THICKNESSES OR
DIMENSIONS AS NOTED PER 207.
T451 PRIMER AND SOLID FILM LUBRICANT.
A PREPARE SURFACES PER 151.
B PRIME ONE COAT SPECIFIED AREA PER 202.
C APPLY SOLID FILM LUBE TO SPECIFIED SURFACES IN THICKNESSES
T452 PRIMER FOR DISSIMILAR METAL PROTECTION ON
SPECIFIED SURFACES
A CLEAN PER 145.
D (INACTIVE FOR NEW DESIGN. SEE T454 FOR PREFERRED CODE.)
T453 WHITE URETHANE, SOLID FILM LUBRICANT AND 16NXXXX

FINISH – TITANIUM ALLOYS
D PAINT SPECIFIED SURFACES WITH WHITE URETHANE PER 222.
T454 PRIMER FOR DISSIMILAR METAL PROTECTION ON SPECIFIED SURFACES

T800 FMS-3014 FORM 2 ADHESIVE PRIMER

ALL TITANIUM ALLOYS
A CLEAN AND APPLY CONVERSION TREATMENT TO ALL SURFACES PER
151 OR CLEAN AND ABRADE ALL SURFACES PER 183.
A - 176

SECTION W. RESTRICTED FINISH CODES
W100 REFER TO FACE OF DRAWING FOR FINISH.

A NOTE: FOR CUSTOMER USE ONLY. NOT FOR LMTAS USE.
W286 PAINTING CREW STATION ASSEMBLIES ON AIRCRAFT
EQUIPPED FOR NIGHT VISION - P6096-2 FLAT BLACK URETHANE.
A EXCEPTION TO FPS-3001 PARAGRAPH 3.5.4.
B CLEAN SURFACES SPECIFIED ON ASSEMBLY DRAWING BY SOLVENT

WIPING WITH P6228-1, P6230-1, OR FMS-2004.
ALUMINUM OXIDE OR EMERY CLOTH.
C FOR AREAS PAINTED GRAY AT DETAIL LEVEL, LIGHTLY ABRADE
EXPOSED SURFACES WITH #320 OR FINER ABRASIVE SUCH AS
ALUMINUM OXIDE OR EMERY CLOTH.
D REWIPE ABRADED SURFACES PER A) ABOVE.
E APPLY ONE COAT OF PRIMER TO ABRADED SURFACES PER 202.
F PAINT EXPOSED SURFACES SPECIFIED ON THE ASSEMBLY DRAWING
WITH P6096-2 FLAT BLACK URETHANE PER 286 (OR 217).
0000 NO FINISH REQUIRED FOR MISC. NON-METALS

A - 177
APPENDIX B. Basic Elements

Basic Basic Element Step(s)
Element
100 NO FINISH REQUIRED.
103 DETAIL OF BONDED ASSEMBLY, DO NOT FINISH.
104 DETAIL OF WELDED ASSEMBLY, DO NOT FINISH.
105 CLEAN PER FPS-3001, PARA. 3.1.1 AND CHEMICAL FILM ALL
SURFACES PER MIL-C-5541.
106 CLEAN PER FPS-3001, PARA. 3.1.1 AND BRUSH CHEMICAL FILM PER
MIL-C-5541, EXTERIOR SURFACES OF BONDED ASSEMBLY. AS AN
ALTERNATE, CHEM FILM MAY BE APPLIED TO EXTERIOR SURFACES OF
BONDED ASSEMBLY BY DIPPING WITH THE FOLLOWING RESTRICTIONS:
1. LEAK TEST SHALL HAVE BEEN PERFORMED.
2. NO ELEVATED TEMPERATURE CLEANING OR DRYING OF THE BONDED
ASSEMBLY SHALL BE EMPLOYED PRIOR TO THE DIPPING OPERATION.
107 CLEAN PER FPS-3001, PARA. 3.1.1 AND CHEMICAL FILM PER
MIL-C-5541 EXTERIOR SURFACES ONLY. TREATMENT IS OPTIONAL
ON INSIDE DIAMETER.
108 CLEAN PER FPS-3001, PARA. 3.1.1 AND CHEMICAL FILM PER
MIL-C-5541 EXTERIOR SURFACES ONLY. TREATMENT NOT PERMITTED
ON INSIDE DIAMETER.
109 CLEAN PER FPS-3001 AFTER FINAL ASSEMBLY.
111 CLEAN AND ANODIZE PER FPS-3033 OR FPS-3090 OR CLEAN PER

FPS-3001 PARA. 3.1.1 AND ANODIZE ALL SURFACES PER MIL-A-8625, TYPE I.
1. IF ELECTRICAL BONDING IS REQUIRED ON SPECIFIED AREAS BY
REFERENCE TO FPS-3024, ANODIZE ONLY THOSE SURFACES NOT
SPECIFIED FOR ELECTRICAL BONDING PER 114. PREPARE SURFACES
SPECIFIED FOR ELECTRICAL BONDING PER MIL-C-5541 CLASS 3.
2. AFTER ANODIZE, INSPECT ANODIZED SURFACE FOR DARKENED
AREAS OF DISCOLORATION WHICH MAY INDICATE SOFT MATERIAL.
PARTS CONTAINING SUCH SPOTS SHALL MEET THE REQUIREMENTS
OF NDTS 1500 PRIOR TO ANODIZE COATING ACCEPTANCE.
112 CLEAN PER FPS-3001, PARA. 3.1.1 AND SULFURIC ACID ANODIZE
ALL SURFACES PER MIL-A-8625, CLASS 1, TYPE II, DUPLEX SEALED
113 CLEAN PER FPS-3001, PARA 3.1.1 AND HARD ANODIZE ALL SURFACES
PER MIL-A-8625, TYPE III, UNSEALED.
REFERENCE TO FPS-3024,
HARD ANODIZE PER 113 ONLY THOSE SURFACES NOT SPECIFIED
FOR ELECTRICAL BONDING. PREPARE SURFACES SPECIFIED FOR
ELECTRICAL BONDING PER MIL-C-5541 CLASS 3.
B-1

Element
FPS-3001, PARA. 3.1.1 AND ANODIZE SPECIFIED SURFACES PER
MIL-A-8625, TYPE I.
REFERENCE TO FPS-3024, ANODIZE ONLY THOSE SURFACES NOT
SPECIFIED FOR ELECTRICAL BONDING PER 114. PREPARE SURFACES
SPECIFIED FOR ELECTRICAL BONDING PER MIL-C-5541 CLASS 3.
2. AFTER ANODIZE, INSPECT ANODIZED SURFACE FOR DARKENED
AREAS OF DISCOLORATION WHICH MAY INDICATE SOFT MATERIAL.
PARTS CONTAINING SUCH SPOTS SHALL MEET THE REQUIREMENTS
OF NDTS 1500 PRIOR TO ANODIZE COATING ACCEPTANCE.
115 CLEAN PER FPS-3001, PARA. 3.1.1 AND HARD ANODIZE SPECIFIED
SURFACES PER MIL-A-8625, TYPE III, UNSEALED.
REFERENCE TO FPS-3024,
OMIT HARD ANODIZE ON SURFACES SPECIFIED FOR ELECTRICAL
BONDING. PREPARE SURFACES SPECIFIED FOR ELECTRICAL BOND-
ING PER MIL-C-5541 CLASS 3.
116 PREPARE SURFACE AND MANGANESE IRON PHOSPHATE TREAT ALL

SURFACES PER FPS-3006, CLASS I. (FOR ALLOY STEEL<180 KSI).

SURFACES PER FPS-3006, CLASS II. (FOR ALLOY STEEL 180-240 KSI).

SURFACES PER FPS-3006, CLASS III. (FOR ALLOY STEEL>240 KSI)
119 CLEAN NOTED SURFACES BY LIGHT SANDING WITH 320 OR FINER

ABRASIVE PAPER AND WIPE CLEAN WITH SOLVENT SUCH AS METHYL
ETHYL KETONE, MIL-C-38736* CLEANER, OR FMS-2004 (FOR GRAPHITE
COMPOSITES).
*NOTE: P6174 NON-AROMATIC CLEANER MAY BE USED IN LIEU OF
MIL-C-38736 CLEANER. (REFERENCE CR 1345 FOR CO-PRODUCER USE.)
120 CLEAN PER FPS-3001, PARA. 3.1.4, AND CADMIUM PLATE ALL
SURFACES PER QQ-P-416, TYPE II, CLASS 2. (FOR ALLOY STEELS
<180 KSI AND FOR SPRINGS).
121 CLEAN PER FPS-3001, PARA. 3.1.4 FOR ALLOY STEEL AND CADMIUM
PLATE ALL SURFACES PER FPS-1007, GRADE A, TYPE II, CLASS 2.
(FOR ALLOY STEEL 180-220 KSI).
122 CLEAN PER FPS-3001, PARA. 3.1.4 FOR ALLOY STEEL, AND CADMIUM
PLATE ALL SURFACES PER FPS-1007, GRADE B, TYPE II, CLASS 2.
(FOR ALLOY STEEL 220-240 KSI).
B-2

Element
123 CLEAN PER FPS-3001, PARA. 3.1.4 FOR ALLOY STEEL AND VACUUM
CADMIUM PLATE ALL SURFACES PER MIL-C-8837, TYPE II, CLASS 2.
(FOR ALLOY STEEL 220-240 KSI - ALTERNATE FOR PROCESSORS NOT
QUALIFIED FOR 122, AND FOR ALLOY STEEL > 240 KSI).
SPECIFIED SURFACES PER MIL-A-8625, CLASS I, TYPE II, DUPLEX SEALED.
125 CLEAN AND APPLY ELECTROLESS NICKEL PLATE ALL SURFACES PER
FPS-3005, CLASS 1.
FPS-3005, CLASS 2.
FPS-3005, CLASS 1. (FOR STEEL 240 KSI OR GREATER).
FPS-3005, CLASS 2. (FOR STEEL LESS THAN 240 KSI STRENGTH).
129 CLEAN PER FPS-3001, PARA. 3.1.3 FOR CRES OR 3.1.4

FOR NON-CRES AND CHROME PLATE SPECIFIED SURFACES
PER QQ-C-320, CLASS 2D. BAKE AFTER PLATING FOR 3 HOURS
MINIMUM. SUSTAINED TENSILE LOAD TESTS ARE NOT REQUIRED.
(FOR ALLOY STEEL LESS THAN OR EQUAL TO 240 KSI WITHOUT
SIGNIFICANT SUSTAINED TENSILE LOADS OR DYNAMIC LOADING).
130 CLEAN PER FPS-3001, PARA. 3.1.4, AND TIN PLATE ALL SURFACES
PER FPS-0030. (FOR ALLOY STEEL).
131 CLEAN AND SILVER PLATE ALL SURFACES PER AMS 2410.
132 CLEAN AND SILVER PLATE ALL SURFACES PER AMS 2412.
133 CLEAN AND CHROME PLATE SPECIFIED SURFACES PER FPS-3004 (FOR
ALLOY STEEL > 240 KSI AND FOR STEEL 180-240 KSI SUBJECTED TO
SIGNIFICANT SUSTAINED TENSION LOADS AND DYNAMIC LOADING).
134 CLEAN PER FPS-3001, PARA. 3.1.1, AND BRUSH CHEMICAL FILM PER
MIL-C-5541 SPECIFIED SURFACES.
135 CLEAN PER FPS-3001, PARA. 3.1.3(A)
136 CLEAN AND BRUSH CADMIUM PLATE SPECIFIED SURFACES PER

FPS-1046, GRADE A, TYPE II, CLASS 2.
137 CLEAN AND BRUSH NICKEL PLATE SPECIFIED SURFACES PER FPS-1046 GRADE B.
138 CLEAN AND APPLY WOOD'S NICKEL STRIKE PER FPS-3022 TO NOTED AREA.
B-3

Element
139 CLEAN PER FPS-3001, PARA. 3.1.1, AND ANODIZE PER MIL-A-8625,
TYPE I, EXTERIOR SURFACES ONLY OF TUBING OR PARTS.
TREATMENT NOT PERMITTED ON INSIDE SURFACES (OXYGEN SYSTEM).

FPS-3001, PARA 3.1.1, AND ANODIZE PER MIL-A-8625, TYPE I
EXTERIOR SURFACES OF TUBING OR PARTS.
TREATMENT IS OPTIONAL ON INSIDE SURFACES OF MACHINED PARTS,
WELDED ASSEMBLIES WET WITH FLUID OR TUBING DETAILS.
141 CLEAN PER FPS-3001, PARA. 3.1.7, AND ANODIZE ALL SURFACES
PER MIL-M-45202, TYPE I, CLASS C. (FOR MAGNESIUM).
142 CLEAN PER FPS-3001, PARA. 3.1.7, AND BRUSH CHROME PICKLE
BARE AREAS PER MIL-M-3171, TYPE I. (FOR MAGNESIUM).
143 CLEAN AND CHROMIUM PLATE SPECIFIED SURFACES PER QQ-C-320,

CLASS 2D, AND BAKE AFTER PLATING 8 HOURS MINIMUM. SUSTAINED
TENSILE LOAD TESTS ARE NOT REQUIRED (220-240 KSI WITHOUT
SIGNIFICANT SUSTAINED TENSILE LOADS OR DYNAMIC LOADING).
144 CLEAN SPECIFIED SURFACE WITH MIL-C-38736 CLEANER* OR FMS-2004.

145 CLEAN PER FPS-3001, PARA. 3.1.2. (FOR TITANIUM ONLY).
146 CLEAN PER FPS-3001 PARA. 3.1.3(A) OR QQ-P-35, AND PASSIVATE

ALL SURFACES PER FPS-3007 OR QQ-P-35 (METAL REMOVAL BY
PASSIVATION SOLUTION NOT PERMITTED). (DO NOT USE FOR
CASTINGS AND WELDED ASSEMBLIES WITH LAP JOINTS.)
NOTE: THIS PROCESS MAY NOT REMOVE HEAT TINT OR DISCOLORATION
RESULTING FROM THE AGING OPERATION.
147 CHEMICAL DESCALE AND PASSIVATE ALL SURFACES PER FPS-3020

(0.00075" METAL REMOVAL PERMITTED) (FOR ROUGH CRES FORGINGS,
FORGED CRES BARS AND FOR HEAT TREATABLE CRES). (NOTE: FPS-
1051 MAY BE USED IN LIEU OF FPS-3020.
FULLY HEAT TREATED PARTS PROCESSED PER FPS-1051 MUST BE
STRESS RELIEVED PER FPS-1051 REQUIREMENTS. CRES PARTS WHICH
HAVE BEEN PRE-PENETRANT ETCHED PER FPS-3020 DO NOT REQUIRE
ADDITIONAL PASSIVATION AFTER PENETRANT INSPECTION PROVIDED
THERE ARE NO SUBSEQUENT MACHINING OPERATIONS.)
NOTE:FOR SURFACES WHERE NO HEAT TREAT, OR MILL SCALE, OR FOR
PARTS WHERE ALL SURFACES ARE MACHINED, QQ-P-35 MAY BE USED
IN LIEU OF FPS-3020.
148 PREPARE ALL SURFACES AND PHOSPHATE TREAT PER FPS-3006,

CLASS VIII, CASTINGS EXCEPTED.
B-4

Element
149 PREPARE SURFACES OF CASTINGS PER FPS-3006, CLASS VIII, STEPS
A AND B ONLY.
151 PREPARE SURFACES AND FLUORIDE-PHOSPHATE TREAT ALL SURFACES

PER FPS-0116 (FOR TITANIUM).
152 CLEAN PER FPS-3001, PARA. 3.1.4, AND CADMIUM PLATE SPECIFIED
SURFACES PER QQ-P-416, TYPE II, CLASS 2. (FOR ALLOY STEEL < 180 KSI).
SURFACES PER FPS-1007, GRADE A, TYPE II, CLASS 2. (FOR
ALLOY STEEL 180-220 KSI).
SURFACES PER FPS-1007, GRADE B, TYPE II, CLASS 2. (FOR
ALLOY STEEL 220-240 KSI).
155 CLEAN PER FPS-3001, PARA. 3.1.4, AND VACUUM CADMIUM PLATE
SPECIFIED SURFACES PER MIL-C-8837, TYPE II, CLASS 2. (FOR
ALLOY STEEL 220-240 KSI - ALTERNATE FOR PROCESSORS NOT
QUALIFIED FOR 154, AND FOR ALLOY STEEL>240 KSI).
156 CLEAN PER FPS-3001, PARA. 3.1.4.
157 CLEAN PER FPS-3001, PARA. 3.1.1 AND HARD ANODIZE SPECIFIED
SURFACES PER MIL-A-8625, TYPE III, CLASS 2; AND DYE TO
APPROXIMATELY GRAY COLOR 36118 OF FED. STD. 595. IRREGULAR
AREAS OF LIGHTER GRAY SHADE DUE TO BLEED OUT FROM POROSITY
ARE ACCEPTABLE (FOR ALUMINUM CASTINGS).
SURFACES PER QQ-P-416, TYPE II, CLASS 2. (FOR COPPER ALLOYS)
SURFACES PER QQ-P-416, TYPE II, CLASS 2. (FOR COPPER ALLOYS)
SURFACES PER QQ-P-416, TYPE II, CLASS 2. (FOR CRES).
161 CLEAN PER FPS-3001, PARA 3.1.3, AND CADMIUM PLATE SPECIFIED
SURFACES PER QQ-P-416, TYPE II, CLASS 2. (FOR CRES).
162 CLEAN, PREPARE SURFACES AND APPLY MOLYBDENUM COATING TO

SPECIFIED SURFACES PER FPS-3002 TO THICKNESS SPECIFIED ON DRAWING.
ALL SURFACES PER MIL-A-8625, TYPE II, CLASS 2, DYED BLACK.
COLOR TO BE SHADE OF BLACK APPROXIMATING COLOR NOS. 36076,
36081, OR 37038 PER FED-STD-595. COLOR TO BE NO LIGHTER
THAN COLOR NO. 36118.
B-5

Element
164 CLEAN AND APPLY ELECTROLESS NICKEL PLATE TO SPECIFIED
SURFACES PER FPS-3005, CLASS 2 (FOR 180-240 KSI ALLOY STEEL).
165 PREPARE SURFACES AND MANGANESE IRON PHOSPHATE TREAT

SPECIFIED SURFACES PER FPS-3006, CLASS III. (FOR ALLOY STEEL>240 KSI).
166 CLEAN AND APPLY WOOD'S NICKEL STRIKE PER FPS-3022 TO ALL SURFACES.
167 CLEAN NICKEL ALLOYS PER FPS-3001, PARA. 3.1.6.
168 CLEAN PER FPS-3001, PARA. 3.1.1, AND BRUSH CHEMICAL FILM ALL
169 CLEAN SPECIFIED SURFACES BY WIPING CLEAN WITH TT-I-735

ISOPROPYL ALCOHOL. CAUTION: DO NOT APPLY M.E.K., ACETONE,
MIL-C-38736 CLEANER, P6174 CLEANER, OR FMS-2004.
170 CLEAN SPECIFIED SURFACES BY LIGHTLY SANDING WITH 220 GRIT

ABRASIVE PAPER OR EQUIVALENT (ABRASIVE PADS) AND WIPE CLEAN
WITH TT-I-735 ISOPROPYL ALCOHOL. CAUTION: DO NOT USE MEK,
ACETONE, MIL-C-38736, P6174, OR FMS-2004 CLEANERS.
171 CLEAN AND APPLY CHROMATE CONVERSION COATING (QQ-P-416,

TYPE 2) TO ALL SURFACES.
172 CLEAN PER FPS-3001, PARA. 3.1.5.
173 COPPER ALLOYS - ELECTROLESS NICKEL PLATE PER MIL-C-26074,

CLASS 1, GRADE B.
174 CLEAN AND PREPARE CURED PRIMED SURFACES PER PARA. 3.7.18 OF FPS-3001.
175 CADMIUM PLATE SPECIFIED SURFACES PER FPS-1007, GRADE A,

TYPE II, CLASS 2 ONTO SURFACES THAT HAVE NOT DRIED AFTER
RECEIPT OF A WOOD'S NICKEL STRIKE (FOR CRES WITH TENSILE
STRENGTH 180-220 KSI).
176 CLEAN PER FPS-3001, PARA. 3.1.1 AND CHEMICAL FILM ALL
SURFACES PER MIL-C-5541, CLASS 3.
177 CLEAN PER FPS-3001, PARA. 3.1.3(A) AND PASSIVATE SPECIFIED

SURFACES PER FPS-3007 (METAL REMOVAL BY PASSIVATION SOLUTION
NOT PERMITTED). (DO NOT USE FOR CASTINGS OR WELD ASSEMBLIES)
178 CLEAN PER FPS-3001, PARA. 3.1.1 AND BRUSH CHEM FILM
SPECIFIED SURFACES PER MIL-C-5541, CLASS 3.
179 COPPER AND COPPER ALLOYS - ELECTROLESS NICKEL PLATE PER

FPS-3005, CLASS 1 TO THE SPECIFIED THICKNESS OR DIMENSIONS.
NO SUBSEQUENT HEAT TREATMENT REQUIRED.
B-6

Element
180 LIGHTLY GRIT BLAST EXPOSED SURFACES WITH 120 MESH ALUMINUM
OXIDE GRIT AT 20-40 PSI, THEN SOLVENT CLEAN USING MIL-C-38736*
181 COPPER AND COPPER ALLOYS: ON EXPOSED COPPER SURFACES ,

EITHER ELECTROLESS NICKEL PLATE PER FPS-3005; CLASS 1
TO SPECIFIED THICKNESS OR DIMENSIONS (WITH NO SUBSEQUENT
HEAT TREATMENT REQUIRED), OR ELECTROLYTICALLY NICKEL PLATE
PER QQ-N-290; CLASS I, GRADE E.
NOTE: GD/FW APPROVAL OF THE NICKEL PLATING PROCESS FOR
COPPER HEAT SINKS IS NOT REQUIRED IF THE PLATING
IS APPLIED IN ACCORDANCE WITH QQ-N-290 OR FPS-3005.
182 ANODIZE SPECIFIED SURFACES PER FPS-3033 OR FPS-3090 OR

MIL-A-8625 TYPE I OR TYPE III (0.0002" THICK).
183 GRIT BLAST CLEAN SURFACES SPECIFIED FOR PAINTING WITH 120
MESH ALUMINUM OXIDE GRIT AT 60-90 PSI, THEN SOLVENT CLEAN
USING MIL-C-38736, P6174, OR FMS-2004 CLEANER.
184 CLEAN, NICKEL STRIKE AND SILVER STRIKE SPECIFIED SURFACES

PER AMS 2410.
185 CLEAN, NICKEL STRIKE, SILVER STRIKE AND SILVER PLATE

SPECIFIED SURFACES PER AMS 2410 TO THE THICKNESS OR
DIMENSIONS SPECIFIED.
186 CLEAN AND CHROMIUM PLATE SPECIFIED SURFACES PER FPS-3036, TO

THE THICKNESS SPECIFIED ON THE DRAWING.
187 PREPARE SURFACES AND FLUORIDE-PHOSPHATE TREAT SPECIFIED

SURFACES PER FPS-0116 (FOR TITANIUM).
188 PREPARE ALL SURFACES AND NICKEL SULFAMATE PLATE PER

MIL-P-27418, 0.0020" +/- 0.0003" THICK. WHILE WET,
CADMIUM PLATE ALL SURFACES PER QQ-P-416, TYPE II, CLASS 2.
B-7

Element
189 REMOVAL OF PEEL PLY FROM GRAPHITE COMPOSITE LAMINATES.
NOTES:
(1) REMOVAL OF PEEL PLY FROM SURFACE SHALL BE VERIFIED BY
QUALITY CONTROL STAMP ON SOIR.
(2) SURFACES WHICH HAVE HAD THE PEEL PLY REMOVED SHALL BE
PROTECTED FROM CONTAMINATION.
(3) CLEAN STARCH FREE, COTTON OR NYLON GLOVES SHALL BE WORN
DURING THE PEELING OPERATION.
(4) IF THE SURFACE OF THE LAMINATE HAS BEEN CONTAMINATED
AFTER THE PEEL PLY HAS BEEN REMOVED, THEN THE SURFACE
SHALL BE SOLVENT CLEANED PER 135, SANDED WITH 280 OR
FINER GRIT WET OR DRY SANDPAPER, SOLVENT CLEAN PER 135
AND WIPE DRY, THEN TACK-RAG TO REMOVE LINT.
A) LOCATE PLY DIRECTION OF TOP LAYER OF COMPOSITE SKIN.
B) MAKE A CUT APPROXIMATELY 1" LONG THRU PEEL PLY USING A
SHARP LEWIS OR EXACTO KNIFE HOLDING THE KNIFE AT A 45
DEGREE ANGLE ALONG THE PLY DIRECTION WHILE MAKING THE
CUT. DO NOT USE ENOUGH PRESSURE ON KNIFE TO CUT COMPOSITE SKIN.
C) THEN INSERT THE EDGE OF A SHARP LINOLEUM KNIFE UNDER
THE CUT MADE IN THE PEEL PLY. USE AN UPWARD MOTION TO
PULL THE PEEL PLY LOOSE. CONTINUE PULLING UNTIL A
SECTION LARGE ENOUGH TO GRASP WITH THE FINGERS IS PEELED UP.
D) REMOVE PEEL PLY FROM THE COMPOSITE SKIN BY PULLING
PARALLEL TO THE FIBER ORIENTATION WITH AN UPWARD MOTION
AND TOWARD THE EDGE(S) OF THE LAMINATE.
201 APPLY ONE COAT OF FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582

PRIMER TO ALL SURFACES. THE PRIMER COATING MAY BE
DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL WHEN THE ENTIRE
LENGTH OF FAYING SURFACE OVERLAPS IS REQUIRED FOR ELECTRICAL
BONDING. THE EQUIVALENT THICKNESS OF TWO COATS OF PRIMER
IS PERMISSIBLE ON THOSE AREAS THAT ARE COVERED WITH TOPCOAT.

PRIMER TO SPECIFIED SURFACE. THE PRIMER COATING
MAY BE DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL WHEN THE
ENTIRE LENGTH OF FAYING SURFACE OVERLAPS IS REQUIRED FOR
ELECTRICAL BONDING. THE EQUIVALENT THICKNESS OF TWO COATS
OF PRIMER IS PERMISSIBLE ON THOSE AREAS THAT ARE COVERED
WITH TOPCOAT.
B-8

Element
PRIMER TO TUBING EXTERIOR SURFACE ONLY. PRIME THE
ENTIRE LENGTH EXCEPT MASK OFF FROM AN END REQUIRED TO
RECEIVE A "PERMASWAGE", "DYNATUBE", C20887, OR C20963
FITTING (NOT FOR USE WITH C7551 FITTINGS). THE MASKED-OFF
DISTANCE IS 0.50 +/- 0.25 INCHES BEYOND THE TUBE INSERTION
MARK (0.50 +/- 0.25 INCHES BEYOND THE VERIFICATION MARK FOR
C20963 FITTINGS).
NOTES: (1) THE PRIMER IS NOT TO COVER ANY OF THE TUBE INSERTION MARK.
(2) IF THE TUBE INSERTION MARK IS NOT APPLIED PRIOR TO APPLICATION
OF PRIMER, MASK OFF 3 +/- 0.25 INCHES FROM AN END REQUIRED TO RECEIVE A
"PERMASWAGE", "DYNATUBE", C20887, OR C20963
FITTING (NOT FOR USE WITH C7551 END FITTINGS).
204 APPLY TWO COATS OF FMS-3027, MIL-PRF-23377 OR MIL-PRF-85582

PRIMER TO ALL SURFACES. THE PRIMER COATING
MAY BE DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL WHEN THE
ENTIRE LENGTH OF FAYING SURFACE OVERLAPS IS REQUIRED FOR
ELECTRICAL BONDING.
205 APPLY TWO COATS OF FMS-3027, MIL-PRF-23377, OR

MIL-PRF-85582 PRIMER TO SPECIFIED SURFACE. THE PRIMER
COATING MAY BE DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL WHEN
THE ENTIRE LENGTH OF FAYING SURFACE OVERLAPS IS REQUIRED FOR
ELECTRICAL BONDING.
206 INSTALL WITH WET TT-P-1757 ZINC CHROMATE PRIMER, MIL-PRF-

23377 EPOXY PRIMER, OR MIL-PRF-85582 WATER-BORNE PRIMER.
(FOR INSTALLING PRESS AND SLIP FIT PARTS, I.E., BEARING BUSHINGS).
207 APPLY FMS-3101 CLASS II OR III SOLID FILM LUBRICANT TO SURFACES NOTED,
PER FPS-3006. USE ONLY LUBRICANTS LISTED ON FQML-3101.
208 COAT ALL SURFACES WITH MIL-C-16173, GRADE 1, CORROSION

PREVENTIVE COMPOUND.


PREVENTIVE COMPOUND (PROTECTED STORAGE REQ'D).
211 APPLY ONE COAT OF MIL-C-22750 EPOXY ENAMEL OR MIL-C-83286 OR MIL-C-85285

URETHANE COATING, GRAY, COLOR 36231, ON SPECIFIED SURFACE.
212 APPLY ONE COAT MIL-C-22750 EPOXY ENAMEL OR MIL-C-83286 OR MIL-C-85285

URETHANE COATING, GRAY, COLOR 36231, TO PRIMED AREA OF TUBING.
B-9

Element
URETHANE COATING, BLACK, COLOR 37038, ON SPECIFIED SURFACE.

URETHANE COATING, BLACK, COLOR 37038, TO PRIMED AREA OF TUBING.

URETHANE COATING, RED, COLOR 11136, ON SPECIFIED SURFACE.

URETHANE COATING, ORANGE-YELLOW, COLOR 13538, ON SPECIFIED SURFACE.
217 APPLY ONE COAT OF P6096-2 FLAT BLACK URETHANE PAINT,

COLOR 37038, ON SPECIFIED SURFACES.
218 PAINT WITH MIL-C-22750 EPOXY ENAMEL OR MIL-C-83286 OR

MIL-C-85285 URETHANE COATING, ALTERNATELY STRIPED BLACK
AND ORANGE-YELLOW, COLORS 37038 AND 13538,
OF THE WIDTHS AND ANGLE SPECIFIED ON THE DRAWING.
219 APPLY AMS-C-27725, TYPE 1 OR 2, FUEL TANK COATING

ON EXTERIOR SURFACE ONLY OF TUBING ASSEMBLIES PER FPS-1004,
EXCEPT MASK OFF FROM AN END REQUIRED TO RECEIVE A
"PERMASWAGE" OR "DYNATUBE" FITTING (NOT FOR USE WITH C7551
END FITTINGS). THE MASKED-OFF DISTANCE IS 1 INCH BEYOND THE
TUBE INSERTION MARK.
NOTES: (1) THE FUEL TANK COATING IS NOT TO COVER ANY OF THE
(2) IF THE TUBE INSERTION MARK IS NOT APPLIED PRIOR
TO APPLICATION OF FUEL TANK COATING, MASK OFF 3
+/- 0.25 INCHES FROM AN END REQUIRED TO RECEIVE
A "PERMASWAGE" OR "DYNATUBE" FITTING (NOT FOR
USE WITH C7551 END FITTINGS).

ON ALL SURFACES PER FPS-1004.

ON SPECIFIED SURFACES PER FPS-1004. (IT IS PERMISSIBLE FOR
THE FUEL TANK COATING TO BE USED IN LIEU OF THE PRIMER
COATING(S) IF NOT TOP COATED OR AS A PRECOAT PRIOR TO THE
APPLICATION OF FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582
PRIMER IN COMPARTMENTS. REACTIVATION OF CURED
AMS-C-27725 COATING PRIOR TO OVERCOATING WITH FMS-3027,
MIL-PRF-23377, OR MIL-PRF-85582 PRIMER IS THE SAME AS FOR
CURED FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582 EPOXY
PRIMER. REFERENCE FPS-3001, PARAGRAPHS 3.2.2
AND 3.4.2 FOR DETAILS.)
B - 10

Element
222 APPLY TWO COATS OF MIL-C-83286 OR MIL-C-85285 URETHANE COAT-
ING, WHITE COLOR 17875 OR 17925, ON SPECIFIED SURFACES.

ING, WHITE COLOR 17875 OR 17925, ON ALL SURFACES.

ING, WHITE COLOR 17875 OR 17925, TO PRIMED AREA OF TUBING.
225 APPLY ONE COAT OF ELEMENT 202 PRIMER AND TWO COATS OF
MIL-C-83286 OR MIL-C-85285 URETHANE COATING OF COLORS
SPECIFIED ON 16N0001 AFTER ASSEMBLY.
226 APPLY MIL-C-83231 RAIN EROSION PROTECTION COATING TO AREAS

SPECIFIED ON 16N0001.

URETHANE COATING, GRAY, COLOR 36231, ON ALL SURFACES.
228 APPLY FMS-3101 CLASS II OR III SOLID FILM LUBRICANT TO SURFACES NOTED,
PER FPS-3006.
229 APPLY ONE COAT OF MIL-C-81751 COATING TO ALL SURFACES.
230 APPLY MIL-L-23398 SOLID FILM LUBRICANT (SPRAY-ON AIR DRY

TYPE), OR FMS-3101 CLASS IV SOLID FILM LUBRICANT,
TO SPECIFIED SURFACES. COATING THICKNESS SHOULD BE
JUST SUFFICIENT TO PRODUCE A SMOOTH, ADHERENT, AND UNIFORM
COATING FREE FROM BLISTERS AND EXCESSIVE BUILDUP. COATING
THICKNESS SHALL BE SUCH THAT IT WILL NOT CAUSE INTERFERENCE
IN A SLIP FIT. FOR EXTERNAL THREAD APPLICATIONS.
INSPECTION MAY BE BY HAND APPLICATION AND REMOVAL OF A
STANDARD NON-SELF LOCKING NUT WITH COMPARABLE TYPE THREADS.
231 INSTALL WITH WET FMS-1044, TYPE V, SEALANT PER FPS-1003. (NON-FUEL AREA).
232 INSTALL WITH WET FMS-1044, TYPE V, SEALANT PER FPS-1004. (FUEL AREA).

URETHANE COATING, FLAT WHITE, COLOR 37875, ON SPECIFIED SURFACES.

URETHANE COATING, BLACK, COLOR 37038, ON ALL SURFACES.
B - 11

Element
235 RESTORE CORROSION PROTECTION BY BRUSH CHEMICAL FILM METHODS
PER MIL-C-5541 ON EDGES OF ALUMINUM PARTS TRIMMED AT
ASSEMBLY, AND MANUFACTURED AND BUCKED HEADS OF ALUMINUM
FASTENERS INSTALLED AT ASSEMBLY LEVEL. SINCE SEALANT OR
AERODYNAMIC SMOOTHER IS SPECIFIED BY THE DRAWING FOR THESE
AREAS, PRIME OR PAINT WILL BE APPLIED AFTER ASSEMBLY PER
16N0001. FINISH HOLES (INCLUDING COUNTERSINKS) FOR REMOVABLE
FASTENERS WHICH DO NOT HAVE INSERTS PER INTERIOR SIDE
FINISHING REQUIREMENTS OR PER 236 IF OPPOSITE SIDE IS A NON-FUEL AREA.
236 RESTORE CORROSION PROTECTION TO EDGES OR SURFACES OF

ALUMINUM PARTS TRIMMED AT ASSEMBLY, MANUFACTURED AND BUCKED
HEADS OF ALUMINUM FASTENERS INSTALLED AT ASSEMBLY LEVEL, AND
TO HOLES (INCLUDING COUNTERSINKS) DRILLED AFTER PAINTING FOR
REMOVABLE FASTENERS WHICH DO NOT HAVE INSERTS. FOR PAINTED
SURFACES CLEAN PER FPS-3001, PARA. 3.1.1(A). BRUSH CHEMICAL
FILM PER MIL-C-5541 AND TOUCH UP WITH TWO COATS OF FMS-3027,
MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER.
237 RESTORE CORROSION PROTECTION TO EDGES OR SURFACE OF ALUMINUM

PARTS TRIMMED AT ASSEMBLY, AND MANUFACTURED AND BUCKED HEADS
OF ALUMINUM FASTENERS INSTALLED AT ASSY. LEVEL. FOR PAINTED
FILM PER MIL-C-5541 AND TOUCH UP WITH ONE COAT OF FMS-3027,
MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER, FOLLOWED
BY TWO COATS OF WHITE URETHANE COATING, COLOR 17875 OR
17925, PER MIL-C-83286 OR MIL-C-85285. FINISH HOLES (IN-
CLUDING COUNTERSINKS) DRILLED AFTER PAINTING FOR REMOVABLE
FASTENERS WHICH DO NOT HAVE INSERTS IN ACCORDANCE WITH THIS
BASIC ELEMENT OR WITH ELEMENT 236.

ALUMINUM PARTS TRIMMED AT ASSEMBLY, AND MANUFACTURED AND
BUCKED HEADS OF ALUMINUM FASTENERS INSTALLED AT ASSEMBLY
LEVEL. FOR PAINTED SURFACES CLEAN PER FPS-3001, PARA.
3.1.1(A). BRUSH CHEMICAL FILM PER MIL-C-5541 AND TOUCH
UP WITH ONE COAT OF FMS-3027, MIL-PRF-23377, MIL-PRF-85582,
OR FMS-1058-1 PRIMER, FOLLOWED BY ONE COAT OF PAINT PER
MIL-C-22750, MIL-C-83286, OR MIL-C-85285, GRAY, COLOR 36231.
B - 12

Element
ALUMINUM PARTS TRIMMED AT ASSEMBLY, AND MANUFACTURED
AND BUCKED HEADS OF ALUMINUM FASTENERS INSTALLED AT
ASSEMBLY LEVEL. FOR PAINTED SURFACES CLEAN PER FPS-3001,
PARA. 3.1.1(A). BRUSH CHEMICAL FILM PER MIL-C-5541 AND
TOUCH UP WITH ONE COAT OF FMS-3027, MIL-PRF-23377, MIL-PRF-
85582, OR FMS-1058-1 PRIMER, FOLLOWED BY ONE COAT OF PAINT
PER MIL-C-22750, MIL-C-83286, OR MIL-C-85285, BLACK,
COLOR 37038.
240 RESTORE CORROSION PROTECTION FINISH TO EDGES OR SURFACES OF

HEADS OF ALUMINUM FASTENERS INSTALLED AT ASSEMBLY LEVEL
(UNLESS THESE HEADS ARE COVERED WITH SEALANT), AND TO HOLES
(INCLUDING COUNTERSINKS) DRILLED AFTER PAINTING FOR
SURFACES CLEAN PER FPS-3001, PARA 3.1.1.(A). BRUSH CHEMICAL
FILM PER MIL-C-5541 AND TOUCH UP WITH AMS-C-27725, TYPE
1 OR 2, URETHANE FUEL TANK COATING PER FPS-1004 OR
EPOXY-AMINE PRIMER PER FMS-1058-1.

TOUCH UP WITH ONE COAT OF FMS-3027, MIL-PRF-23377,
MIL-PRF-85582, OR FMS-1058-1 PRIMER, FOLLOWED BY ONE COAT
OF P6096-2 NONREFLECTIVE BLACK COATING.

MIL-PRF-85582, OR FMS-1058-1 PRIMER.

LEVEL. FOR PAINTED SURFACES CLEAN PER FPS-3001,
85582, OR FMS-1058-1 PRIMER, FOLLOWED BY ONE COAT OF PAINT
PER MIL-C-22750, MIL-C-83286, OR MIL-C-85285, ORANGE-YELLOW,
COLOR 13538.
B - 13

Element
3.1.1(A). BRUSH CHEMICAL FILM PER MIL-C-5541 AND TOUCH UP
WITH ONE COAT OF FMS-3027, MIL-PRF-23377, MIL-PRF-85582,
OR FMS-1058-1 PRIMER, FOLLOWED BY THE REQUIRED BLACK OR
ORANGE-YELLOW PAINT, COLORS 37038 AND 13538, PER
MIL-C-22750, MIL-C-83286, OR MIL-C-85285, AS APPLICABLE.
245 THE SECOND COAT OF PRIMER MAY BE DELAYED TO SUBSEQUENT

ASSEMBLY LEVEL PROVIDED ALL SURFACES EXCEPT FAYING SURFACES
ARE ACCESSIBLE. (EXAMPLE: THE UNDERSIDE OF A HAT SECTION
AFTER ASSEMBLY WOULD NOT BE ACCESSIBLE AND THUS MUST BE
GIVEN TWO COATS OF PRIMER PRIOR TO ASSEMBLY).
246 RESTORE CORROSION PROTECTION BY BRUSH CHEMICAL FILM METHODS

PER MIL-C-5541 ON EDGES OF ALUMINUM PARTS TRIMMED AT
ASSEMBLY, AND MANUFACTURED AND BUCKED HEADS OF ALUMINUM
FASTENERS INSTALLED AT ASSEMBLY LEVEL. SINCE SEALANT OR
AERODYNAMIC SMOOTHER IS SPECIFIED BY THE DRAWING FOR THESE
AREAS, PRIME OR PAINT WILL BE APPLIED AFTER ASSEMBLY PER
16N0005. FINISH HOLES (INCLUDING COUNTERSINKS) FOR REMOV-
ABLE FASTENERS WHICH DO NOT HAVE INSERTS PER INTERIOR SIDE
FINISHING REQUIREMENTS OR PER 236 IF OPPOSITE SIDE IS A NON-FUEL AREA.
250 COAT SPECIFIED SURFACES WITH MIL-C-16173, GRADE 4, CORROSION

251 APPLY ONE COAT OF ELEMENT 202 PRIMER AND TWO COATS OF
MIL-C-83286 OR MIL-C-85285 URETHANE COATING OF COLORS
SPECIFIED ON 16N0003.
252 APPLY TWO COATS OF MIL-C-83286 OR MIL-C-85285 URETHANE

COATING, BLACK, COLOR 37038, ON SPECIFIED SURFACES.

ING, LIGHT GRAY, COLOR 36375, ON ALL SURFACES.

ING, LIGHT GRAY, COLOR 36375, ON SPECIFIED SURFACES.
B - 14

Element
LEVEL. FOR PAINTED SURFACES CLEAN PER FPS-3001, PARA
WITH ONE COAT OF FMS-3027, MIL-PRF-23377, MIL-PRF-85582, OR
FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF MIL-C-83286 OR
MIL-C-85285 LIGHT GRAY URETHANE COATING, COLOR 36375. FINISH
HOLES (INCLUDING COUNTERSINKS) DRILLED AFTER PAINTING FOR
REMOVABLE FASTENERS WHICH DO NOT HAVE INSERTS IN ACCORDANCE
WITH THIS BASIC ELEMENT OR WITH ELEMENT 236.
256 RESTORE CORROSION PROTECTION FINISH TO EDGES OR SURFACES

OF PLASTIC PARTS TRIMMED OR ABRAIDED AT ASSEMBLY, AND
MANUFACTURED AND BUCKED HEADS OF ALUMINUM FASTENERS
INSTALLED AT ASSEMBLY LEVEL. TOUCH UP WITH ONE COAT OF
FMS-3027, MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER,
FOLLOWED BY TWO COATS OF WHITE URETHANE COATING, COLOR
17875 OR 17925, PER MIL-C-83286 OR MIL-C-85285.

ING, DARK GRAY, COLOR 36320, ON SPECIFIED SURFACES.

FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF MIL-C-83286 OR
MIL-C-85285 DARK GRAY URETHANE COATING, COLOR 36320. FINISH
259 APPLY TWO COATS OF FMS-1027, TYPE 5, TEFLON-URETHANE

COATING DARK GRAY, COLOR 36320, ON SPECIFIED SURFACES PER FPS-0004.

MIL-PRF-85582, OR FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS
OF FMS-1027, TYPE 5, TEFLON-URETHANE COATING DARK GRAY,
COLOR 36320.
B - 15

Element
261 APPLY TWO COATS OF FMS-1027, TYPE 5, TEFLON-URETHANE COATING
LIGHT GRAY, COLOR 36375, ON SPECIFIED SURFACES PER FPS-0004.
262 RESTORE CORROSION PROTECTION TO EDGE OR SURFACES OF

MIL-PRF-85582, OR FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS
OF FMS-1027, TYPE 5, TEFLON-URETHANE COATING, LIGHT GRAY,
COLOR 36375, PER FPS-0004.

ING, DARK GRAY, COLOR 36320, ON ALL SURFACES.
266 APPLY ONE COAT OF P6096-2 OPTICAL NON-REFLECTIVE COATING,

BLACK, COLOR 37038, ON ALL SURFACES.
267 APPLY TWO COATS OF FMS-1027, TYPE 5, TEFLON-URETHANE

COATING, DARK GRAY, COLOR 36320, ON ALL SURFACES PER FPS-0004.
269 DELETED - DUPLICATE OF 215.

UP WITH ONE COAT OF FMS-3027, MIL-PRF-23377, MIL-PRF-85582,
OR FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF BLACK
URETHANE COATING, COLOR 37038, PER MIL-C-83286 OR
MIL-C-85285. FINISH HOLES (INCLUDING COUNTERSINKS) DRILLED
AFTER PAINTING FOR REMOVABLE FASTENERS WHICH DO NOT HAVE
INSERTS IN ACCORDANCE WITH THIS BASIC ELEMENT OR WITH ELEMENT 236.
271 APPLY ONE COAT OF MIL-C-22750 EPOXY ENAMEL OR MIL-C-83286 OR

MIL-C-85285 URETHANE COATING, ORANGE-YELLOW, COLOR 13538, ON ALL
SURFACES.

PRIMER TO EXTERIOR SURFACE TO END OF TUBES WITH
BEADED ENDS OR TO BASE OF SLEEVE ON TUBES WITH FLARED ENDS.

ON EXTERIOR SURFACE TO BASE OF SLEEVE ON TUBES WITH FLARED ENDS.
B - 16

Element
274 THE APPLICATION OF WHITE PAINT MAY BE DELAYED TO A SUBSE-
QUENT ASSEMBLY LEVEL. IF WHITE PAINT IS APPLIED AT A LATER
TIME, PREVIOUSLY PRIMED SURFACES SHALL BE SOLVENT CLEANED
(MIL-C-38736* OR FMS-2004), SCUFFED TO REMOVE GLOSS WITH 320
GRIT SANDPAPER OR "SCOTCHBRITE", RE-WIPED WITH SOLVENT
CLEANER, THEN MIST COATED WITH FMS-3027, MIL-PRF-23377, OR
MIL-PRF-85582 PRIMER, FOLLOWED BY TWO COATS OF
URETHANE, WHITE COLOR 17875 OR 17925, PER MIL-C-83286 OR
MIL-C-85285 APPLIED TO ALL EXPOSED SURFACES.
275 APPLY ONE COAT OF MIL-L-19537 OR MIL-L-81352 CLEAR

ACRYLIC LACQUER TO LETTERED FACE OF NAME PLATES AFTER
INSTALLATION.
276 THE APPLICATION OF LIGHT GRAY URETHANE PAINT MAY BE DELAYED

TO A SUBSEQUENT ASSEMBLY LEVEL. IF LIGHT GRAY URETHANE
PAINT IS APPLIED AT A LATER TIME, PREVIOUSLY PRIMED SURFACES
SHALL BE SOLVENT CLEANED (MIL-C-38736* OR FMS-2004), SCUFFED
TO REMOVE GLOSS WITH 320 GRIT SANDPAPER OR "SCOTCHBRITE",
REWIPED WITH SOLVENT CLEANER, THEN MIST COATED WITH
FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582 PRIMER, FOLLOWED
BY TWO COATS OF LIGHT GRAY URETHANE COATING, COLOR 36375,
APPLIED TO ALL EXPOSED SURFACES.
277 THE APPLICATION OF DARK GRAY URETHANE PAINT MAY BE DELAYED

TO A SUBSEQUENT ASSEMBLY LEVEL. IF DARK GRAY URETHANE PAINT
IS APPLIED AT A LATER TIME, PREVIOUSLY PRIMED SURFACES SHALL
BE SOLVENT CLEANED (MIL-C-38736* OR FMS-2004), SCUFFED TO
REMOVE GLOSS WITH 320 GRIT SANDPAPER OR "SCOTCHBRITE", RE-
WIPED WITH SOLVENT, THEN MIST COATED WITH FMS-3027,
MIL-PRF-23377, OR MIL-PRF-85582 PRIMER, FOLLOWED BY TWO
COATS OF DARK GRAY URETHANE COATING, COLOR 36320, APPLIED
TO ALL EXPOSED SURFACES.
278 APPLY ONE COAT OF MIL-C-83286 OR MIL-C-85285 URETHANE COAT-

ING, LUSTERLESS GRAY, COLOR 36231, ON ALL SURFACES.

ING, LUSTERLESS BLACK, COLOR 37038, ON ALL SURFACES.
B - 17

Element
280 THE APPLICATION OF LUSTERLESS GRAY URETHANE PAINT MAY BE
DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL. IF LUSTERLESS GRAY
URETHANE PAINT IS APPLIED AT A LATER TIME, PREVIOUSLY PRIMED
SURFACES SHALL BE SOLVENT CLEANED (MIL-C-38736*OR FMS-2004),
SCUFFED TO REMOVE GLOSS WITH 320 GRIT SANDPAPER OR "SCOTCH-
BRITE", RE-WIPED WITH SOLVENT CLEANER, THEN MIST COATED WITH
FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582 PRIMER,
FOLLOWED BY ONE COAT OF LUSTERLESS GRAY URETHANE COATING,
COLOR 36231, PER MIL-C-83286 OR MIL-C-85285, APPLIED TO ALL
CREW COMPARTMENT EXPOSED SURFACES.
281 THE APPLICATION OF LUSTERLESS BLACK URETHANE PAINT MAY BE

DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL. IF LUSTERLESS BLACK
FOLLOWED BY ONE COAT OF LUSTERLESS BLACK URETHANE COATING
COLOR 37038, PER MIL-C-83286 OR MIL-C-85285, APPLIED TO ALL
CREW COMPARTMENT EXPOSED SURFACES.

ING, LUSTERLESS GRAY, COLOR 36231, ON SPECIFIED SURFACES.

ING, LUSTERLESS BLACK, COLOR 37038, ON SPECIFIED SURFACES.

FMS-1058-1 PRIMER, FOLLOWED BY ONE COAT OF LUSTERLESS GRAY
B - 18

Element
FMS-1058-1 PRIMER, FOLLOWED BY ONE COAT OF LUSTERLESS BLACK
286 THE APPLICATION OF P6096-2 FLAT BLACK URETHANE PAINT MAY BE

DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL. IF P6096-2 FLAT
BLACK URETHANE PAINT IS APPLIED AT A LATER TIME, PREVIOUSLY
PRIMED SURFACES SHALL BE SOLVENT CLEANED (MIL-C-38736* OR
FMS-2004), SCUFFED TO REMOVE GLOSS WITH 320 GRIT SANDPAPER
OR "SCOTCHBRITE", RE-WIPED WITH SOLVENT CLEANER, THEN MIST
COATED WITH FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582
PRIMER, FOLLOWED BY ONE COAT OF P6096-2 FLAT BLACK URETHANE
COATING APPLIED TO ALL CREW COMPARTMENT EXPOSED SURFACES.
287 THE APPLICATION OF LIGHT GRAY TEFLON-URETHANE PAINT MAY BE

DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL. IF LIGHT GRAY
TEFLON-URETHANE PAINT IS APPLIED AT A LATER TIME, PREVIOUSLY
PRIMED SURFACES SHALL BE SOLVENT CLEANED (MIL-C-38736* OR
FMS-2004), SCUFFED TO REMOVE GLOSS WITH 320 GRIT SANDPAPER
OR "SCOTCHBRITE", RE-WIPED WITH SOLVENT CLEANER, THEN MIST
COATED WITH FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582
PRIMER, FOLLOWED BY TWO COATS OF LIGHT GRAY TEFLON-URETHANE
COATING, COLOR 36375, APPLIED TO ALL EXPOSED SURFACES.
288 THE APPLICATION OF DARK GRAY TEFLON-URETHANE PAINT MAY BE

DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL. IF DARK GRAY TEFLON-
FOLLOWED BY TWO COATS OF DARK GRAY TEFLON-URETHANE COATING.
COLOR 36320, APPLIED TO ALL EXPOSED SURFACES.
NOTE: P6174 NON-AROMATIC CLEANER MAY BE USED IN LIEU OF
B - 19

Element
ING, GRAY COLOR 36270, ON ALL SURFACES.

ING, GRAY COLOR 36270, ON SPECIFIED SURFACES.

FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF GRAY URETHANE
COATING COLOR 36270, PER MIL-C-83286 OR MIL-C-85285. FINISH
292 THE APPLICATION OF GRAY COLOR 36270 URETHANE PAINT MAY BE

DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL. IF GRAY COLOR 36270
FOLLOWED BY TWO COATS OF GRAY COLOR 36270 URETHANE COATING
PER MIL-C-83286 OR MIL-C-85285 APPLIED TO ALL EXPOSED SURFACES.
293 APPLY TWO COATS OF MIL-L-81352 ACRYLIC LACQUER, OR

MIL-C-83286 OR MIL-C-85285 URETHANE COATING, WHITE COLOR
17875 OR 17925, ON ALL SURFACES.
294 APPLY TWO COATS OF MIL-L-81352 ACRYLIC LACQUER OR

17875 OR 17925, ON SPECIFIED SURFACES.
B - 20

Element
295 RESTORE CORROSION PROTECTION TO EDGES OR SURFACES OF ALUM.
PARTS TRIMMED AT ASSEMBLY, AND MANUFACTURED & BUCKED HEADS
BY TWO COATS OF MIL-L-81352 WHITE ACRYLIC LACQUER OR
MIL-C-83286 OR MIL-C-85285 WHITE URETHANE COATING, COLOR
17875 OR 17925, (WHICHEVER WAS PREVIOUSLY APPLIED). FINISH
296 THE APPLICATION OF WHITE ACRYLIC LACQUER OR WHITE URETHANE

COATING MAY BE DELAYED TO A SUBSEQUENT ASSEMBLY LEVEL. IF
WHITE ACRYLIC LACQUER OR WHITE URETHANE COATING IS APPLIED
AT A LATER TIME, PREVIOUSLY PRIMED SURFACES SHALL BE SOLVENT
CLEANED (MIL-C-38736* OR FMS-2004), OR WITH TT-I-735 ISOPRO-
PYL ALCOHOL IF ADJACENT TO ACRYLIC COATED PARTS, SCUFFED TO
REMOVE GLOSS WITH 320 GRIT SANDPAPER OR "SCOTCHBRITE", RE-
WIPED WITH SOLVENT CLEANER, THEN MIST COATED WITH FMS-3027,
MIL-PRF-23377, OR MIL-PRF-85582 PRIMER, FOLLOWED
BY TWO COATS OF MIL-L-81352 WHITE ACRYLIC LACQUER OR TWO
COATS OF MIL-C-83286 OR MIL-C-85285 WHITE URETHANE COATING,
COLOR 17875 OR 17925, APPLIED TO ALL EXPOSED SURFACES.
297 WITH DOOR AND HINGE ASSEMBLED (MINUS LATCH) AND THE SUB-
ASSEMBLY IN THE CLOSED POSITION, CLEAN AND PREPARE EXPOSED
INTERIOR SURFACES PER PARA. 3.7.18 OF FPS-3001.

FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF URETHANE OR
TEFLON-URETHANE COATING OF THE COLOR SPECIFIED ON THE
APPLICABLE 16NXXXX AIRCRAFT PAINTING DWG. FINISH HOLES
299 APPLY TWO COATS OF MIL-L-81352 ACRYLIC LACQUER OR

17875 OR 17925, TO PRIMED AREA OF TUBING.
B - 21

Element
300 CORROSION INHIBITIVE ADHESIVE PRIMER, FMS-3018, FORM II,
MAY BE APPLIED TO ALL SURFACES OF ALUMINUM DETAILS OF A
BONDED ASSEMBLY AND PROCESSED IN ACCORDANCE WITH FPS-3016.
301 APPLY TWO COATS OF FMS-1027, TYPE 5, TEFLON URETHANE COATING

MEDIUM GRAY COLOR 36270 ON ALL SURFACES.

FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF FMS-1027,TYPE 5,
TEFLON URETHANE COATING, MEDIUM GRAY, COLOR 36270 PER FPS-0004.
303 APPLY TWO COATS OF MIL-L-81352 LUSTERLESS RED ACRYLIC

LACQUER COLOR 31136 TO SPECIFIED SURFACES.

LEVEL. BRUSH CHEMICAL FILM PER MIL-C-5541, AND TOUCH UP
FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF LUSTERLESS RED
ACRYLIC LACQUER PER MIL-L-81352 COLOR 31136.
305 APPLY FMS-1082 SOLID FILM LUBRICANT TO ALL SURFACES PER FPS-1037.
306 APPLY ONE COAT OF MIL-C-8514 WASH PRIMER TO SPECIFIED SURFACES.
307 RESTORE CORROSION PROTECTION TO EDGES AND SURFACES (E.G.,

HOLES, COUNTERSINKS, SPOTFACES, ETC.) OF NON-CORROSION
RESISTANT STEEL ALLOYS THAT HAVE BEEN MACHINED AFTER INITIAL
CORROSION PROTECTION HAS BEEN APPLIED. FOR PAINTED SURFACES
CLEAN PER FPS-3001, PARA. 3.1.4 AND TOUCH UP WITH ONE COAT
OF FMS-3027, MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER.

CLEAN PER FPS-3001, PARA. 3.1.4 AND TOUCH UP WITH TWO COATS
OF FMS-3027, MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER.
B - 22

Element
CLEAN PER FPS-3001, PARA. 3.1.4. TOUCH UP WITH ONE COAT OF
FMS-3027, MIL-PRF-23377, MIL-PRF-85582,OR FMS-1058-1 PRIMER,
FOLLOWED BY ONE COAT OF MIL-C-22750 EPOXY ENAMEL OR MIL-
C-83286 OR MIL-C-85285 URETHANE COATING, GRAY, COLOR 36231.

FOLLOWED BY ONE COAT OF MIL-C-22750 EPOXY ENAMEL OR MIL-C
C-83286 OR MIL-C-85285 URETHANE COATING, BLACK, COLOR 37038.

FMS-3027, MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1
PRIMER, FOLLOWED BY ONE COAT OF MIL-C-22750 EPOXY ENAMEL OR
MIL-C-83286 OR MIL-C-85285 URETHANE COATING, BLACK OR ORANGE
YELLOW, COLORS 37038 & 13538 (WHICHEVER WAS PREVIOUSLY APPLIED).

FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285 WHITE
URETHANE COATING, COLOR 17875 OR 17925.

FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285 DARK
GRAY URETHANE COATING, COLOR 36320.
B - 23

Element
FOLLOWED BY ONE COAT OF MIL-C-83286 OR MIL-C-85285 LUSTER-
LESS BLACK URETHANE COATING, COLOR 37038.

CORROSION PROTECTION HAS BEEN APPLIED. FOR SURFACES TREATED
WITH SOLID FILM LUBRICANT, CLEAN PER FPS-3001, PARA. 3.1.4
AND APPLY MIL-L-23398 LUBRICANT (SPRAY-ON TYPE), OR
FMS-3101 CLASS IV LUBRICANT, TO SPECIFIED
SURFACES. COATING THICKNESS SHOULD BE JUST SUFFICIENT TO
PRODUCE A SMOOTH, ADHERENT, AND UNIFORM COATING FREE FROM
BLISTERS AND EXCESSIVE BUILDUP. COATING THICKNESS SHALL BE
SUCH THAT IT WILL NOT CAUSE INTERFERENCE IN A SLIP FIT.
FOR EXTERNAL THREAD APPLICATIONS. INSPECTION MAY BE BY HAND
APPLICATION AND REMOVAL OF A STANDARD NON-SELF LOCKING NUT
WITH COMPARABLE TYPE THREADS.
316 APPLY ONE COAT OF MIL-C-8514 WASH PRIMER TO ALL SURFACES.

HOLES, COUNTERSINKS, SPOTFACES, ETC.) OF COPPER ALLOYS THAT
HAVE BEEN MACHINED AFTER INITIAL CORROSION PROTECTION HAS
BEEN APPLIED. FOR PAINTED SURFACES, CLEAN PER FPS-3001,
PARA. 3.1.5. TOUCH UP WITH ONE COAT OF FMS-3027, MIL-PRF-
23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER, FOLLOWED BY ONE
COAT OF MIL-C-22750 EPOXY ENAMEL OR MIL-C-83286 OR
MIL-C-85285 URETHANE COATING, BLACK, COLOR 37038.

HOLES, COUNTERSINKS, SPOTFACES, ETC.) OF NICKEL ALLOYS THAT
MIL-C-85285 URETHANE COATING, GRAY, COLOR 36231.
B - 24

Element
MIL-C-85285 URETHANE COATING, RED, COLOR 11136.

BEEN APPLIED. FOR SURFACES TREATED WITH SOLID FILM LUBRICANT
CLEAN PER FPS-3001, PARA. 3.1.6 AND APPLY MIL-L-23398
LUBRICANT (SPRAY-ON TYPE), OR FMS-3101 CLASS IV
LUBRICANT, TO SPECIFIED SURFACES. COATING
THICKNESS SHOULD BE JUST SUFFICIENT TO PRODUCE A SMOOTH,
ADHERENT, AND UNIFORM COATING FREE FROM BLISTERS AND
EXCESSIVE BUILDUP. COATING THICKNESS SHALL BE SUCH THAT IT
WILL NOT CAUSE INTERFERENCE IN A SLIP FIT. FOR EXTERNAL
THREAD APPLICATIONS, INSPECTION MAY BE BY HAND APPLICATION
AND REMOVAL OF A STANDARD NON-SELF LOCKING NUT WITH COMPAR-
ABLE TYPE THREADS.

HOLES, COUNTERSINKS, SPOTFACES, ETC.) OF CORROSION RESISTANT
STEEL ALLOYS THAT HAVE BEEN MACHINED AFTER INITIAL CORROSION
PROTECTION HAS BEEN APPLIED. FOR PAINTED SURFACES, CLEAN
PER FPS-3001, PARA. 3.1.3(A) AND TOUCH UP WITH ONE COAT OF
FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582 PRIMER.

PER FPS-3001, PARA. 3.1.3(A). TOUCH UP WITH ONE COAT OF
FOLLOWED BY ONE COAT OF MIL-C-22750 EPOXY ENAMEL OR MIL-
C-83286 OR MIL-C-85285 URETHANE COATING, GRAY, COLOR 36231.

FOLLOWED BY ONE COAT OF MIL-C-22750 EPOXY ENAMEL OR
C-83286 OR MIL-C-85285 URETHANE COATING, BLACK, COLOR 37038.
B - 25

Element
FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285 WHITE
URETHANE COATING, COLOR 17875 OR 17925.

PER FPS-3001, PARA. 3.1.3(A). TOUCH UP WITH AMS-C-27725,
TYPE 1 OR 2, FUEL TANK COATING.

PROTECTION HAS BEEN APPLIED. FOR PAINTED SURFACES, CLEAN PER
FPS-3001, PARA. 3.1.3(A) AND TOUCH UP WITH FMS-3027, MIL-
PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER, FOLLOWED
BY TWO COATS OF MIL-C-83286 OR MIL-C-85285 WHITE URETHANE
COATING, COLOR 17875 OR 17925 OR TWO COATS OF URETHANE
OR TEFLON-URETHANE COATING OF THE COLOR SPECIFIED ON THE
APPLICABLE 16N0001 AIRCRAFT PAINTING DRAWING (WHICHEVER WAS
PREVIOUSLY APPLIED).

HAS BEEN APPLIED. FOR PAINTED SURFACES, CLEAN PER FPS-3001,
PARA. 3.1.3(A). TOUCH UP WITH ONE COAT OF FMS-3027,
MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER,
GRAY URETHANE COATING, COLOR 36320 (IF PREVIOUSLY APPLIED).

MIL-C-83286 OR MIL-C-85285 URETHANE COATING, FLAT WHITE, COLOR 37875.
B - 26

Element
FOLLOWED BY TWO COATS OF URETHANE OR TEFLON-URETHANE COATING
OF THE COLOR SPECIFIED ON THE APPLICABLE 16NXXXX AIRCRAFT
PAINTING DWG.

FOLLOWED BY ONE COAT OF P6096-2 OPTICAL NON-REFLECTIVE BLACK
COATING, COLOR 37038.

MIL-C-83286 OR MIL-C-85285 URETHANE COATING, BLACK OR
ORANGE-YELLOW, COLORS 37038 & 13538 (WHICHEVER WAS PREVIOUSLY
APPLIED).

MIL-C-83286 OR MIL-C-85285 URETHANE COATING, ORANGE-YELLOW,
COLOR 13538.

GRAY URETHANE COATING, COLOR 36320.
B - 27

Element
OF THE COLOR SPECIFIED ON THE APPLICABLE 16N0001 AIRCRAFT
PAINTING DWG (WHICHEVER WAS PREVIOUSLY APPLIED).

LESS BLACK URETHANE COATING, COLOR 37038.

LESS GRAY URETHANE COATING, COLOR 36231.

LESS GRAY URETHANE COATING, COLOR 36231 (IF PREVIOUSLY APPLIED).

FOLLOWED BY TWO COATS OF MIL-L-81352 WHITE ACRYLIC LACQUER
OR MIL-C-83286 OR MIL-C-85285 WHITE URETHANE COATING, COLOR
17875 OR 17925, (WHICHEVER WAS PREVIOUSLY APPLIED).
B - 28

Element
339 RESTORE CORROSION PROTECTION TO EDGES & SURFACES (E.G., HOLES
COUNTERSINKS, SPOTFACES, ETC.) OF CORROSION RESISTANT STEEL
ALLOYS THAT HAVE BEEN MACHINED AFTER INITIAL CORROSION PRO-
TECTION HAS BEEN APPLIED. FOR PAINTED SURFACES, CLEAN PER
FPS-3001, PARA. 3.1.3(A). TOUCH UP WITH ONE COAT OF
GRAY URETHANE COATING, COLOR 36320 OR TWO COATS OF
URETHANE OR TEFLON-URETHANE COATING OF THE COLOR SPECIFIED
ON THE APPLICABLE 16N0001 AIRCRAFT PAINTING DRAWING
(WHICHEVER WAS PREVIOUSLY APPLIED).

PROTECTION HAS BEEN APPLIED. FOR PAINTED SURFACES TREATED
WITH SOLID FILM LUBRICANT, CLEAN PER FPS-3001, PARA.
3.1.3(A) AND APPLY MIL-L-23398 LUBRICANT (SPRAY-ON TYPE),
OR FMS-3101 CLASS IV LUBRICANT,
TO SPECIFIED SURFACES. COATING THICKNESS SHOULD BE JUST
SUFFICIENT TO PRODUCE A SMOOTH, ADHERENT, AND UNIFORM
COATING FREE FROM BLISTERS AND EXCESSIVE BUILDUP. COATING
THICKNESS SHALL BE SUCH THAT IT WILL NOT CAUSE INTERFERENCE
IN A SLIP FIT. FOR EXTERNAL THREAD APPLICATIONS, INSPECTION
MAY BE BY HAND APPLICATION AND REMOVAL OF A STANDARD NON-
SELF LOCKING NUT WITH COMPARABLE TYPE THREADS.

HOLES, COUNTERSINKS, SPOTFACES, ETC.) OF TITANIUM ALLOYS
THAT HAVE BEEN MACHINED AFTER INITIAL CORROSION PROTECTION
23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER, FOLLOWED BY
TWO COATS OF MIL-C-83286 OR MIL-C-85285 WHITE URETHANE
COATING, COLOR 17875 OR 17925.

3.1.2. TOUCH UP WITH ONE COAT OF FMS-3027, MIL-PRF-23377,
MIL-PRF-85582,OR FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF
ON THE APPLICABLE 16N0001 AIRCRAFT PAINTING DWG (IF APPLICABLE).
B - 29

Element
PARA. 3.1.2. TOUCH UP WITH ONE COAT OF FMS-3027,
MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER.

HAS BEEN APPLIED. FOR SURFACES TREATED WITH SOLID FILM
LUBRICANT, CLEAN PER FPS-3001, PARA. 3.1.2 AND APPLY
MIL-L-23398 LUBRICANT (SPRAY-ON TYPE), OR FMS-3101
CLASS IV LUBRICANT, TO SPECIFIED SURFACES.
COATING THICKNESS SHOULD BE JUST SUFFICIENT TO PRODUCE A
SMOOTH, ADHERENT, AND UNIFORM COATING FREE FROM BLISTERS AND
ABLE TYPE THREADS.

OF THE COLOR SPECIFIED ON THE APPLICABLE 16NXXXX AIRCRAFT
PAINTING DWG. (WHICHEVER WAS PREVIOUSLY APPLIED).
348 RESTORE CORROSION PROTECTION TO EDGES & SURFACES(E.G., HOLES

FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285 LIGHT
ON THE APPLICABLE 16N0001 AIRCRAFT PAINTING DRAWING
(WHICHEVER WAS PREVIOUSLY APPLIED).
B - 30

Element
FOLLOWED BY TWO COATS OF FMS-1027, TYPE 5, TEFLON URETHANE
COATING MEDIUM GRAY COLOR 36270.

LEVEL. BRUSH CHEMICAL FILM PER MIL-C-5541 AND TOUCH UP WITH
ONE COAT OF FMS-3027, MIL-PRF-23377, MIL-PRF-85582, OR
FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF FMS-1027,
TYPE 4, TEFLON-URETHANE COATING, WHITE COLOR, PER FPS-0004.

WHITE COLOR, ON SPECIFIED SURFACES PER FPS-0004.

WHITE COLOR, ON ALL SURFACES PER FPS-0004.
353 RESTORE CORROSION PROTECTION TO EDGES & SURFACES (E.G., HOLES

FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285 LIGHT
ON THE APPLICABLE 16N0001 AIRCRAFT PAINTING (WHICHEVER WAS

MEDIUM GRAY, COLOR 36270, ON SPECIFIED SURFACES.

LEVEL. FOR PAINTED SURFACES, CLEAN PER FPS-3001, PARA.
3.1.1(A). BRUSH CHEMICAL FILM PER MIL-C-5541, CLASS 3 AND
85582, OR FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF
FMS-1027, TYPE 5, TEFLON URETHANE COATING, MEDIUM GRAY,
COLOR 36270 PER FPS-0004 (IF PREVIOUSLY APPLIED).
B - 31

Element
3.1.1(A). BRUSH CHEMICAL FILM PER MIL-C-5541.

FMS-1058-1 PRIMER, FOLLOWED BY ONE COAT OF MIL-C-22750 EPOXY
ENAMEL OR MIL-C-83286 OR MIL-C-85285 URETHANE COATING,
FLAT WHITE, COLOR 37875.
358 WIPE CLEAN WITH SOLVENT SUCH AS METHYL ETHYL KETONE OR

MIL-C-38736 CLEANER. WIPE DRY.
359 CLEAN SURFACES SPECIFIED TO BE COATED WITH P6194-1 BY LIGHT

SANDING WITH 320 GRIT OR FINER ABRASIVE PAPER.
360 APPLY P6194-1 COATING (0.015" +/- 0.005" THICK) TO SPECIFIED

AREAS AND ALLOW TO CURE 24 HOURS.

HOLES, COUNTERSINKS, SPOTFACES, ETC.) OF ALUMINUM ALLOYS
HAS BEEN APPLIED. FOR PAINTED SURFACES CLEAN PER FPS-3001,
PARA. 3.1.1(A). TOUCH UP WITH ONE COAT OF FMS-3027,
COATING, COLOR 17875 OR 17925.

HOLES, COUNTERSINKS, SPOTFACES, ETC.) OF ALUMINUM ALLOYS
HAS BEEN APPLIED. FOR SURFACES TREATED WITH SOLID FILM
LUBRICANT, CLEAN PER FPS-3001, PARA. 3.1.1(A). AND APPLY
MIL-L-23398 LUBRICANT (SPRAY-ON TYPE), OR FMS-3101 CLASS IV
LUBRICANT, TO SPECIFIED SURFACES.
SMOOTH, ADHERENT, AND UNIFORM COATING FREE FROM BLISTERS AND
ABLE TYPE THREADS.
B - 32

Element
363 CLEAN PER FPS-3001, PER PARA 3.1.4.2 (FOR 180-220 KSI ALLOY STEELS).
364 APPLY FMS-0074 OR FMS-1104 BY BRUSH OR PUTTY KNIFE. SPREAD

OVER DESIGNATED AREA WITH TEFLON SCRAPER (FMS-1104 SPREDS
EASIER AND MORE UNIFORMLY IF WARMED TO 150 DEGREE FAHRENHEIT
MAXIMUM.) WORK MATERIAL INTO POROUS SURFACES WITH TEFLON
SCRAPER. ALLOW TO CURE TO SANDABLE CONDITION.
365 LEAK CHECK ASSEMBLY PER FPS-3016, PARA. 8.3.4.
366 PRIME SPECIFIED EXPOSED EXTERIOR SURFACES WITH ONE COAT OF

FMS-3035 FLEXIBLE, CORROSION RESISTANT PRIMER.
367 PRIME SPECIFIED SURFACES WITH TWO COATS OF FMS-3035 FLEXIBLE

COROSION RESISTANT PRIMER.
368 ELECTROLYTICALLY NICKEL PLATE EXPOSED COPPER AND COPPER

ALLOY SURFACES PER QQ-N-290, CLASS I, GRADE E.
NOTE: GD/FW APPROVAL OF THE NICKEL PLATING PROCESS FOR
COPPER HEAT SINKS IS NOT REQUIRED IF THE PLATING IS
APPLIED IN ACCORDANCE WITH QQ-N-290.
369 CLEAN PER FPS-3001, PARAGRAPH 3.1.3, AND CHROME PLATE ALL
SURFACES PER QQ-C-320, CLASS 2D. BAKE AFTER PLATING FOR
3 HOURS MINIMUM. ALL SURFACES AND THICKNESSES TO BE 0.0005 TO 0.0020.

HOLES, COUNTERSINKS, ETC.) OF GRP THAT HAS BEEN MACHINED
AFTER INITIAL CORROSION PROTECTION HAS BEEN APPLIED. FOR
PAINTED SURFACES, BUFF WITH 320 (OR FINER) ABRASIVE PAPER
& WIPE CLEAN WITH TT-M-261 MEK, FMS-2004, OR MIL-C-38736
(P6174 NON-AROMATIC CLEANER MAY BE USED IN LIEU OF MIL-C-
38736 CLEANER). TOUCH UP WITH ONE COAT OF FMS-3035 FLEXIBLE
CORROSION RESISTANT PRIMER FOLLOWED BY TWO COATS OF
MIL-C-83286 OR MIL-C-85285 WHITE URETHANE COATING; COLOR NO.
17875 (OR COLOR NO. 17925).

CORROSION PROTECTION HAS BEEN APPLIED. CLEAN AND BRUSH
CADMIUM PLATE PER FPS-1046, GRADE A, TYPE II, CLASS 2.
TOUCH UP WITH AMS-C-27725, TYPE 1 OR 2, URETHANE
FUEL TANK COATING PER FPS-1004.
B - 33

Element
CLEAN AND BRUSH CADMIUM PLATE PER FPS-1046, GRADE A, TYPE II
CLASS 2. TOUCH UP WITH ONE COAT OF FMS-3027, MIL-PRF-23377,
MIL-PRF-85582,OR FMS-1058-1 PRIMER, FOLLOWED BY TWO COATS OF
MIL-L-81352 WHITE ACRYLIC LACQUER OR TWO COATS OF MIL-C-
83286 OR MIL-C-85285 WHITE URETHANE COATING, COLOR NO. 17875
(OR COLOR NO. 17925).
373 APPLY FMS-3011 FORM II ADHESIVE PRIMER TO ALL SURFACES.

APPLICATION, PRIMER THICKNESS, AND CURE SHALL BE PER FPS-3016.
374 APPLY FMS-3011 FORM II ADHESIVE PRIMER TO SPECIFIED SURFACES

APPLICATION, PRIMER THICKNESS, & CURE SHALL BE PER FPS-3016.

BUCKED HEADS OF ALUMINUM FASTENERS WHICH DO NOT HAVE INSERTS
CLEAN PER FPS-3001; PARA 3.1.1(A). BRUSH CHEM FILM PER MIL-C-5541 AND
TOUCH UP WITH FMS-3011 FORM II ADHESIVE PRIMER PER FPS-3016.
376 GRIT BLAST SPECIFIED SURFACES PER FPS-3006, CLASS VII (STEPS "A" AND
“B” ONLY).
377 GRIT BLAST ALL SURFACES PER FPS-3006, CLASS VII (STEPS "A" AND “B”
ONLY FOR 300 SERIES CRES).
378 APPLY TWO COATS OF MIL-C-83286 OR MIL-C-85285 URETHANE COATING,

BLUE COLOR 35109, ON SPECIFIED SURFACES.

BLUE COLOR 35109, ON ALL SURFACES.

BY TWO COATS OF BLUE URETHANE COATING, COLOR 35109,
PER MIL-C-83286 OR MIL-C-85285. FINISH HOLES (INCLUDING
COUNTERSINKS) DRILLED AFTER PAINTING FOR REMOVABLE
B - 34

Element
381 THE APPLICATION OF BLUE PAINT MAY BE DELAYED TO A SUBSEQUENT
ASSEMBLY LEVEL. IF BLUE PAINT IS APPLIED AT A LATER
GRIT SANDPAPER OR "SCOTCHBRITE", RE-WIPED WITH SOLVENT
URETHANE, BLUE COLOR 35109, PER MIL-C-83286 OR
MIL-C-38736 CLEANER. (REFERENCE CR 1345 FOR COPRODUCER USE.)

FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285 BLUE
URETHANE COATING, COLOR 35109.
400 APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO ALL SURFACES PER FPS-3035.
B - 35

Element
401 TO TOUCH UP SCRATCHES IN THE FMS-3014 FORM 2 ADHESIVE PRIMER
SURFACE WHICH WERE INCURRED PRIOR TO THE ELEVATED TEMPERA-
TURE CURE OF FMS-3014 FORM 1 ADHESIVE (SEE FPS-3035 FOR THE
ADHESIVE CURE CYCLE), DETERMINE THE LOCATION AND DEPTH OF
THE SCRATCH AND PROCEED AS INSTRUCTED BELOW.
SCRATCHES IN THE ADHESIVE PRIME SURFACE WHICH DO NOT EXTEND
INTO THE ALUMINUM SURFACE SHALL BE REPAIRED AS
FOLLOWS: SOLVENT CLEAN THE AREA WITH TT-M-261 MEK, FMS-2004
OR MIL-C-38736 CLEANER AS APPROPRIATE PER FPS-3035*.
APPLY A BRUSH COAT OF FMS-3014 FORM 2 ADHESIVE PRIMER TO
THE SCRATCHED AREA PER FPS-3035. (NOTE: TOUCH UP IS NOT
REQUIRED IF THE SCRATCH IS IN AN AREA WHICH WILL BE SUB-
SEQUENTLY COVERED WITH FMS-3014 FORM 1 ADHESIVE).
SCRATCHES IN THE ADHESIVE PRIMER SURFACE WHICH EXTEND INTO
THE ALUMINUM SURFACE SHALL BE REPAIRED AS FOLLOWS:
SOLVENT CLEAN THE AREA WITH TT-M-261 MEK, FMS-2004, OR
MIL-C-38736 AS APPROPRIATE PER FPS-3035*. BUFF THE SCRATCHED
AREA WITH 320 GRIT SANDPAPER OR "SCOTCH-BRITE"
AND DRY WIPE. RESTORE CORROSION PROTECTION TO
EDGES OR SURFACES OF ALUMINUM PARTS TRIMMED AT ASSEMBLY,
MANUFACTURED AND BUCKED HEADS OF ALUMINUM FASTENERS
INSTALLED AT ASSEMBLY LEVEL, AND TO HOLES (INCLUDING
COUNTERSINKS) DRILLED AFTER PAINTING (FOR REMOVABLE FASTEN-
ERS WHICH DO NOT HAVE INSERTS) BY CHEMICAL FILM METHODS PER
MIL-C-5541 FOLLOWED BY A COAT OF FMS-3014 FORM 2 ADHESIVE
PRIMER APPLIED PER FPS-3035.
*NOTE: FOR SCRATCHES INCURRED PRIOR TO THE FPS-3035 ELEVATED
TEMPERATURE CURE OF FMS-3014 FORM 2 ADHESIVE PRIMER,
WIPE WITH TT-M-261 METHYL ETHYL KETONE. FOR SCRATCH
INCURRED AFTER THIS PRIMER CURE CYCLE, WIPE WITH
MIL-C-38736 (OR P6174 NON-AROMATIC CLEANER. REFERENCE
CR 1345 FOR CO-PRODUCER USE), OR FMS-2004.
B - 36

Element
402 TO TOUCH UP SCRATCHES IN THE FMS-3014 FORM 2 ADHESIVE
PRIMER SURFACE WHICH WERE INCURRED AFTER THE ELEVATED
TEMPERATURE CURE OF FMS-3014 FORM 1 ADHESIVE (SEE FPS-3035
FOR THE ADHESIVE CURE CYCLE), CLEAN THE AREA WITH FMS-2004,
MIL-C-38736 CLEANER (OR P6174 NON-AROMATIC CLEANER)*. BUFF
THE SCRATCHED AREA WITH 320 GRIT SANDPAPER OR "SCOTCH-BRITE"
AND DRY WIPE.
IF THE SCRATCH EXTENDS INTO THE ALUMINUM SURFACE,
THEN RESTORE CORROSION PROTECTION BY CHEMICAL FILM METHODS
PER MIL-C-5541. RESTORE CORROSION PROTECTION TO EDGES OR
SURFACES OF ALUMINUM PARTS TRIMMED AT ASSEMBLY, MANUFACTURED
AND BUCKED HEADS OF ALUMINUM FASTENERS INSTALLED AT ASSEMBLY
LEVEL, AND TO HOLES (INCLUDING COUNTERSINKS) DRILLED AFTER
PAINTING (FOR REMOVABLE FASTENERS WHICH DO NOT HAVE INSERTS)
BY CHEMICAL FILM METHODS PER MIL-C-5541. FOR FUEL EXPOSED
AREAS, APPLY A COAT OF AMS-C-27725 FUEL TANK COATING OR
FMS-1058-1 PER FPS-3035. FOR NON-FUEL EXPOSED AREAS, APPLY
A COAT OF FMS-1058-1 PER FPS-3035 OR A COAT OF FMS-3027,
MIL-PRF-23377, OR MIL-PRF-85582 PRIMER.
MIL-C-38736 CLEANER. (REFERENCE CR 1345 FOR CO-PRODUCER USE).
403 APPLY FMS-3014 FORM 2 ADHESIVE PRIMER TO SPECIFIED SURFACES PER FPS-3035.

TO HOLES (INCLUDING COUNTERSINKS) DRILLED AFTER PAINTING
(FOR REMOVABLE FASTENERS WHICH DO NOT HAVE INSERTS) BY CHEM
FILM METHODS PER MIL-C-5541. TOUCH UP WITH ONE COAT OF
FMS-3027, MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER.
FOR PAINTED SURFACES, CLEAN PER FPS-3001; PARA. 3.1.1(A).
BUFF THE SCRATCHED AREA WITH 320 GRIT SANDPAPER OR "SCOTCH-
BRITE" AND RE-WIPE WITH MIL-C-38736* OR FMS-2004 CLEANER.
IF THE SCRATCH EXTENDS INTO THE ANODIZED
ALUMINUM SURFACE, THEN RESTORE CORROSION PROTECTION BY CHEM
FILM METHODS PER MIL-C-5541. APPLY A MIST-COAT OF FMS-3027,
MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER, AND
SUBSEQUENTLY APPLY TWO COATS OF WHITE URETHANE; COLOR
NO. 17875 OR COLOR NO. 17925 PER MIL-C-83286 OR MIL-C-85285.
B - 37

Element
405 FOR AREAS PRIMED ONLY:
RESTORE CORROSION PROTECTION TO EDGES OR SURFACES OF
ALUMINUM PART TRIMMED AT ASSEMBLY, MANUFACTURED AND BUCKED
TO HOLES (INCLUDING COUNTERSINKS) DRILLED AFTER PAINTING
(FOR REMOVABLE FASTENERS WHICH DO NOT HAVE INSERTS) BY CHEM
FILM METHODS PER MIL-C-5541. TOUCH UP WITH ONE COAT OF
FMS-3027, MIL-PRF-23377, MIL-PRF-85582,OR FMS-1058-1 PRIMER.
FOR AREAS PRIMED AND PAINTED WHITE ONLY:
FOR PAINTED SURFACES, CLEAN PER FPS-3001, 3.1.1(A). BUFF
THE SCRATCHED AREA WITH 320 GRIT SANDPAPER OR "SCOTCH-BRITE"
AND RE-WIPE WITH MIL-C-38736*, P6174, OR FMS-2004
CLEANER. IF THE SCRATCH EXTENDS INTO THE ANODIZED ALUMINUM
SURFACE, THEN RESTORE CORROSION PROTECTION BY CHEMICAL FILM
METHODS PER MIL-C-5541. APPLY A MIST-COAT OF FMS-3027,
MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER, AND
SUBSEQUENTLY APPLY TWO COATS OF MIL-L-81352 WHITE ACRYLIC
LACQUER OR MIL-C-83286 OR MIL-C-85285 WHITE URETHANE COATING
COLOR NO. 17875 OR COLOR NO. 17925.
406 THE APPLICATION OF WHITE URETHANE COATING SHALL BE AS

FOLLOWS: THE CURED FMS-3014 FORM 2 ADHESIVE PRIMED SURFACE
SHALL BE SOLVENT CLEANED WITH MIL-C-38736* OR FMS-2004,
SCUFFED WITH 320 GRIT SANDPAPER OR "SCOTCHBRITE" TO REMOVE
GLOSS, RE-WIPED WITH SOLVENT CLEANER*, AND MIST-COATED WITH
SUBSEQUENTLY, TWO COATS OF WHITE URETHANE COATING (COLOR NO.
17875 OR 17925) SHALL BE APPLIED TO SPECIFIED SURFACES PER
MIL-C-83286 OR MIL-C-85285.
407 THE APPLICATION OF WHITE ACRYLIC LACQUER OR WHITE URETHANE

SHALL BE AS FOLLOWS: THE CURED FMS-3014 FORM 2 ADHESIVE
PRIMED SURFACE SHALL BE SOLVENT CLEANED WITH MIL-C-38736* OR
FMS-2004, BUFFED WITH 320 GRIT SANDPAPER OR "SCOTCHBRITE"
TO REMOVE GLOSS, RE-WIPED WITH SOLVENT CLEANER,* AND THEN
MIST-COATED WITH FMS-3027, MIL-PRF-23377, OR MIL-PRF-85582
PRIMER. SUBSEQUENTLY, TWO COATS OF WHITE ACRYLIC
LACQUER OR WHITE URETHANE (COLOR NUMBER 17875 OR 17925)
PER MIL-L-81352 OR MIL-C-83286 OR MIL-C-85285 SHALL BE
APPLIED TO SPECIFIED SURFACES.
B - 38

Element
408 APPLY FMS-3014 FORM 2 ADHESIVE PRIMER
ON EXTERIOR SURFACE ONLY OF TUBING ASSEMBLIES PER FPS-3035,
EXCEPT MASK OFF FROM AN END REQUIRED TO RECEIVE A
"PERMASWAGE" OR "DYNATUBE" FITTING (NOT FOR USE WITH C7551
END FITTINGS). THE MASKED-OFF DISTANCE IS 1 INCH BEYOND THE
NOTES: (1) THE ADHESIVE PRIMER IS NOT TO COVER ANY OF THE
(2) IF THE TUBE INSERTION MARK IS NOT APPLIED PRIOR
TO APPLICATION OF ADHESIVE PRIMER, MASK OFF 3
+/- 0.25 INCHES FROM AN END REQUIRED TO RECEIVE
A "PERMASWAGE" OR "DYNATUBE" FITTING (NOT FOR
USE WITH C7551 END FITTINGS).
409 APPLY FMS-3014 FORM 2 ADHESIVE PRIMER ON EXTERIOR SURFACE

TO BASE OF SLEEVE ON TUBES WITH FLARED ENDS.
500 CLEAN AND APPLY ELECTROLESS NICKEL PLATE TO SPECIFIED

SURFACES PER FPS-3005, CLASS 1. (FOR 180-240 KSI ALLOY STEEL).
501 CLEAN PER FPS-3001, PARA 3.1.1 AND ANODIZE PER MIL-A-8625,
TYPE I OR II, SPECIFIED EXTERIOR SURFACES OF TUBING
OR PARTS. TREATMENT IS OPTIONAL ON INSIDE SURFACES OF
MACHINED PARTS, WELDED ASSEMBLIES WET WITH FLUID OR TUBING DETAILS.
502 CLEAN PER FPS-3001, PARA. 3.1.1 AND CHEM FILM SPECIFIED
503 CLEAN AND APPLY ELECTROLESS NICKEL PLATING TO SPECIFIED

SURFACES PER MIL-C-26074, CLASS 4, GRADE B.
504 CLEAN AND APPLY CADMIUM PLATING TO NICKEL PLATED SURFACES

PER QQ-P-416, CLASS 3, TYPE II.
505 APPLY MIL-C-85054 WATER DISPLACING, CORROSION PREVENTIVE

COMPOUND TO SPECIFIED SURFACES.
506 APPLY TWO COATS OF FMS-1058-1 PRIMER ON SPECIFIED SURFACES.

HEADS OF ALUMINUM FASTENERS INSTALLED AT ASSEMBLY LEVEL
(UNLESS THESE HEADS ARE COVERED WITH SEALANT), AND TO HOLES
SURFACES CLEAN PER FPS-3001, PARA 3.1.1(A). BRUSH CHEMICAL
PER MIL-C-5541 AND TOUCH UP WITH FMS-1058-1 PRIMER.
B - 39

Element
508 RESTORE CORROSION PROTECTION TO EDGES AND SURFACES
(E.G. HOLES, COUNTERSINKS, SPOTFACES, ETC) OF CORROSION
CORROSION PROTECTION HAS BEEN APPLIED. FOR PAINTED SURFACES,
CLEAN PER FPS-3001, PARA. 3.1.3(A). TOUCH UP WITH ONE COAT
OF FMS-3027, MIL-PRF-23377, MIL-PRF-85582, OR FMS-1058-1
PRIMER FOLLOWED BY ONE COAT OF MIL-C-22750 EPOXY ENAMEL OR
MIL-C-83286 OR MIL-C-85285 URETHANE COATING, RED COLOR 11136.
509 CLEAN ALL SURFACES WITH MIL-C-38736* OR FMS-2004 CLEANER.

510 APPLY MIL-L-23398 SOLID FLIM LUBRICANT (SPRAY-ON AIR DRY

TYPE), OR FMS-3101 CLASS IV LUBRICANT, TO ALL SURFACES.
SMOOTH, ADHERENT, AND UNIFORM COATING FREE FROM BLISTERS
AND EXCESSIVE BUILDUP. COATING THICKNESS SHOULD BE SUCH
THAT IT WILL NOT CAUSE INTERFERENCE IN A SLIP FIT.
511 STRIP CADMIUM PLATING PER MIL-STD-871 SOLUTION 3 AND REPLATE

PER ORIGINAL CADMIUM PLATING REQUIREMENTS.
NOTE: ELEMENT 511 IS NOT TO BE USED FOR ANY STEEL WITH
TENSILE STRENGTH GREATER THAN 240 KSI.
512 APPLY TWO COATS OF MIL-C-83286 OR MIL-C-85285 COATING, RED

COLOR 11136, ON SPECIFIED SURFACES.

OF ALUMINUM FASTENERS INSTALLED AT ASSEMBLY LEVEL. FOR
PAINTED SURFACES CLEAN PER FPS-3001, PARA. 3.1.1 (A). BRUSH
CHEMICAL FILM PER MIL-C-5541 WITH ONE COAT OF FMS-3027,
FOLLOWED BY TWO COATS OF RED URETHANE COATING, COLOR
11136, PER MIL-C-83286 OR MIL-C-85285. FINISH HOLES (INC-
LUDING COUNTERSINKS) DRILLED AFTER PAINTING FOR REMOVABLE
514 STRIP EXISTING CHEMICAL FILM AND APPLY MIL-C-5541 CHEMICAL

FILM TO ALL SURFACES PER PROCESS STANDARD 74.02-2.
515 APPLY P5438-2 LIGHT GRAY (COLOR 36375) POLYURETHANE RAIN

EROSION RESISTANT COATING TO SPECIFIED SURFACES PER FPS-3045.
B - 40

Element
516 CLEAN PER FPS-3001, PARA 3.1.4 (CLEANING PROCESS ONLY) AND
APPLY IVD ALUMINUM TO ALL SURFACES PER MIL-C-83488, TYPE II,
CLASS 3, FOLLOWED BY GLASS BEAD PEENING PER FPS-3083. (FOR
ALLOY STEEL.)
517 CLEAN PER FPS-3001, PARA. 3.1.4 (CLEANING PROCESS ONLY) AND
APPLY IVD ALUMINUM TO SPECIFIED SURFACES PER MIL-C-83488,
TYPE II, CLASS 3, FOLLOWED BY GLASS BEAD PEENING PER
FPS-3083. (FOR ALLOY STEEL.)
518 CLEAN PER FPS-3001, PARA. 3.1.5(A) AND APPLY IVD ALUMINUM TO
ALL SURFACES PER MIL-C-83488, TYPE II, CLASS 3, FOLLOWED BY
GLASS BEAD PEENING PER FPS-3083. (FOR COPPER ALLOYS.)
519 CLEAN PER FPS-3001, PARA 3.1.5(A) AND APPLY IVD ALUMINUM TO
SPECIFIED SURFACES PER MIL-C-83488, TYPE II, CLASS 3,
FOLLOWED BY GLASS BEAD PEENING PER FPS-3083. (FOR COPPER ALLOYS.)
520 CLEAN PER FPS-3001, PARA. 3.1.3(A) AND APPLY IVD ALUMINUM TO
ALL SURFACES PER MIL-C-83488, TYPE II, CLASS 3, FOLLOWED BY
GLASS BEAD PEENING PER FPS-3083. (FOR CRES.)
521 CLEAN PER FPS-3001, PARA 3.1.3(A) AND APPLY IVD ALUMINUM TO
SPECIFIED SURFACES PER MIL-C-83488, TYPE II, CLASS 3,
FOLLOWED BY GLASS BEAD PEENING PER FPS-3083. (FOR CRES.)
522 PREPARE SURFACE AND MANGANESE IRON PHOSPHATE TREAT SPECIFIED

SURFACES PER FPS-3006, CLASS I. (FOR ALLOY STEEL < 180 KSI).
B - 41

Element
SURFACE* WHICH WERE INCURRED PRIOR TO THE ELEVATED TEMPERA-
TURE CURE OF FMS-3014 FORM 1 ADHESIVE (SEE FPS-3035 FOR THE
ADHESIVE CURE CYCLE).
SCRATCHES IN THE ADHESIVE PRIMER SURFACE SHALL BE REPAIRED
AS FOLLOWS:
SOLVENT CLEAN THE AREA WITH TT-M-261 METHYL ETHYL KETONE, OR
MIL-C-38736, FMS-2004, P6174, OR APPROVED ALTERNATE AS
APPROPRIATE PER FPS-3035*. BUFF THE SCRATCHED AREA WITH 320
GRIT SANDPAPER OR "SCOTCH-BRITE" AND REWIPE WITH SOLVENT
CLEANER. APPLY ONE COAT OF FMS-3014 FORM 2 ADHESIVE PRIMER
PER FPS-3035. (FOR CRES AND TITANIUM ALLOYS).
*NOTES: (1) TOUCH UP IS NOT REQUIRED IF THE SCRATCH IS IN
AN AREA WHICH WILL BE SUBSEQUENTLY COVERED WITH
FMS-3014 FORM 1 ADHESIVE.
(2) FOR SCRATCHES INCURRED PRIOR TO THE FPS-3035
ELEVATED TEMPERATURE CURE OF FMS-3014 FORM 2 ADHE-
SIVE PRIMER, WIPE WITH TT-M-261 METHYL ETHYL KETONE
OR APPROVED ALTERNATE. FOR SCRATCHES INCURRED
AFTER THIS PRIMER CURE CYCLE, WIPE WITH MIL-C-38736
OR APPROVED ALTERNATE. (P6174 NON-AROMATIC CLEANER
MAY BE USED IN LIEU OF MIL-C-38376 CLEANER. RE-
FERENCE CR 1345 FOR COPRODUCER USE).

SURFACE WHICH WERE INCURRED AFTER THE ELEVATED TEMPERATURE
CURE OF FMS-3014 FORM 1 ADHESIVE (SEE FPS-3035 FOR THE ADHESIVE
CURE CYCLE).
SCRATCHES IN THE ADHESIVE SURFACE SHALL BE REPAIRED AS FOLLOWS:
SOLVENT WIPE THE AREA WITH MIL-C-38736, FMS-2004 OR APPROVED
ALTERNATE*. BUFF THE SCRATCHED AREA WITH 320 GRIT SANDPAPER
OR "SCOTCH-BRITE" AND REWIPE WITH SOLVENT CLEANER. FOR FUEL
EXPOSED AREAS, APPLY ONE COAT OF FMS-1058-1 OR AMS-C-27725
FUEL TANK COATING PER FPS-3035. FOR NONFUEL EXPOSED AREAS,
APPLY A COAT OF FMS-1058-1 PER FPS-3035 OR A COAT OF
(FOR CRES AND TITANIUM ALLOYS).
MIL-C-38736 CLEANER. REFERENCE CR 1345 FOR CO-PROPRODUCER USE.

526 WRAP ENTIRE PART WITH MIL-P-3420, CLASS AND STYLE AS REQUIRED, FORM B.

GRAY COLOR 36118, ON SPECIFIED SURFACES.
B - 42

Element
23377, MIL-PRF-85582, OR FMS-1058-1 PRIMER, FOLLOWED BY TWO
COATS OF MIL-C-83286 OR MIL-C-85285 GRAY URETHANE COATING, COLOR 36118.

GRAY COLOR 36118, ON ALL SURFACES.

FOLLOWED BY TWO COATS OF DARK GRAY URETHANE COATING, COLOR
36118, PER MIL-C-83286 OR MIL-C-85285. FINISH HOLES (INCLUDING
COUNTERSINKS) DRILLED AFTER PAINTING FOR REMOVABLE
531 APPLY ONE COAT OF FMS-3027, MIL-P-23377E TYPE 1 CLASS 1, OR

DEFT 44-GN-36 PRIMER TO ALL SURFACES. THE PRIMER
THE ENTIRE LENGTH OF FAYING SURFACE OVERLAPS IS REQUIRED
FOR ELECTRICAL BONDING. THE EQUIVALENT THICKNESS OF TWO
COATS OF PRIMER IS PERMISSIBLE ON THOSE AREAS THAT ARE
COVERED WITH TOPCOAT.
532 APPLY FMS-3049 COATING, PER FPS-3057, TO SPECIFIED

SURFACES. THE THICKNESS OF THE COATING SHALL BE AS
SPECIFIED BY THE ENGINEERING DRAWING.
533 APPLY FMS-2026 COATING TO SPECIFIED SURFACES PER FPS-3076.

THE COLOR OF THE COATING SHALL BE AS SPECIFIED BY THE
APPLICABLE AIRCRAFT PAINTING DRAWING.
535 APPLY ONE COAT OF FMS-3027, MIL-P-23377E TYPE 1 CLASS 1, OR

DEFT 44-GN-36 PRIMER TO SPECIFIED SURFACES. THE
PRIMER COATING MAY BE DELAYED TO A SUBSEQUENT ASSEMBLY
LEVEL WHEN THE ENTIRE LENGTH OF FAYING SURFACE OVERLAPS IS
REQUIRED FOR ELECTRICAL BONDING. THE EQUIVALENT THICKNESS
OF TWO COATS OF PRIMER IS PERMISSIBLE ON THOSE AREAS THAT
ARE COVERED WITH TOPCOAT.
B - 43

Element
TOUCH UP WITH ONE COAT OF FMS-3027, MIL-P-23377E TYPE 1,
CLASS 1, OR DEFT 44-GN-36 PRIMER.
537 APPLY TWO COATS OF FMS-3027, MIL-P-23377E TYPE 1 CLASS 1,

OR DEFT 44-GN-36 PRIMER TO ALL SURFACES. THE PRIMER
THE ENTIRE LENGTH OF FAYING SURFACE OVERLAPS IS REQUIRED
FOR ELECTRICAL BONDING.
538 APPLY TWO COATS OF FMS-3027, MIL-P-23377E TYPE 1 CLASS 1,

OR DEFT 44-GN-36 PRIMER TO SPECIFIED SURFACE. THE
PRIMER COATING MAY BE DELAYED TO A SUBSEQUENT ASSEMBLY
LEVEL WHEN THE ENTIRE LENGTH OF FAYING SURFACE OVERLAPS IS
REQUIRED FOR ELECTRICAL BONDING.

HEADS OF ALUMINUM FASTENERS INSTALLED AT ASSEMBLY LEVEL,
AND TO HOLES (INCLUDING COUNTERSINKS) DRILLED AFTER
PAINTING FOR REMOVABLE FASTENERS WHICH DO NOT HAVE INSERTS.
FOR PAINTED SURFACES CLEAN PER FPS-3001, PARA. 3.1.1(A).
BRUSH CHEMICAL FILM PER MIL-C-5541 AND TOUCH UP WITH TWO
COATS OF FMS-3027, MIL-P-23377E TYPE 1 CLASS 1, OR
DEFT 44-GN-36 PRIMER.

HOLES, COUNTERSINKS, ETC.) OF GRP THAT HAS BEEN MACHINED
AFTER INITIAL CORROSION PROTECTION HAS BEEN APPLIED. FOR
PAINTED SURFACES, BUFF WITH 320 (OR FINER) ABRASIVE PAPER
& WIPE CLEAN WITH TT-M-261 MEK, FMS-2004, OR MIL-C-38736
(P6174 NON-AROMATIC CLEANER MAY BE USED IN LIEU OF MIL-C-
38736 CLEANER). TOUCH UP WITH ONE COAT OF FMS-3027,
MIL-PRF-23377, MIL-PRF-85582 PRIMER, OR FMS-1058-1 , FOLLOWED
COATING; COLOR NO. 17875 (OR COLOR NO. 17925).

ING, GRAY COLOR 26493, ON ALL SURFACES.
B - 44

Element
542 THE APPLICATION OF GRAY PAINT MAY BE DELAYED TO A SUBSE-
QUENT ASSEMBLY LEVEL. IF GRAY PAINT IS APPLIED AT A LATER
GRIT SANDPAPER OR “SCOTCHBRITE”, RE-WIPED WITH SOLVENT
URETHANE, GRAY COLOR 26493, PER MIL-C-83286 OR

BY TWO COATS OF GRAY URETHANE COATING, COLOR 26493,
PER MIL-C-83286 OR MIL-C-85285. FINISH HOLES (IN-

ING, GRAY COLOR 26493, ON SPECIFIED SURFACES.

MIL-P-23377E TYPE 1 CLASS 1, OR DEFT 44-GN-36 PRIMER,
FOLLOWED BY TWO COATS OF WHITE URETHANE COATING, COLOR 17875
OR 17925, PER MIL-C-83286 OR MIL-C-85285. FINISH HOLES (IN-
B - 45

Element
546 THE APPLICATION OF WHITE PAINT MAY BE DELAYED TO A SUBSE-
QUENT ASSEMBLY LEVEL. IF WHITE PAINT IS APPLIED AT A LATER
GRIT SANDPAPER OR “SCOTCHBRITE”, RE-WIPED WITH SOLVENT
CLEANER, THEN MIST COATED WITH FMS-3027, MIL-P-23377E
TYPE 1 CLASS 1, OR DEFT 44-GN-36 PRIMER, FOLLOWED BY TWO
COATS OF URETHANE, WHITE COLOR 17875 OR 17925, PER MIL-C-
83286 OR MIL-C-85285 APPLIED TO ALL EXPOSED SURFACES.
547 THE APPLICATION OF LIGHT GRAY URETHANE PAINT MAY BE DELAYED

TO A SUBSEQUENT ASSEMBLY LEVEL. IF LIGHT GRAY URETHANE
PAINT IS APPLIED AT A LATER TIME, PREVIOUSLY PRIMED SURFACES
SHALL BE SOLVENT CLEANED (MIL-C-38736* OR FMS-2004), SCUFFED
TO REMOVE GLOSS WITH 320 GRIT SANDPAPER OR "SCOTCHBRITE",
REWIPED WITH SOLVENT CLEANER, THEN MIST COATED WITH
FMS-3027, MIL-P-23377E TYPE 1 CLASS 1, OR DEFT 44-GN-36
PRIMER, FOLLOWED BY TWO COATS OF LIGHT GRAY URETHANE
COATING, COLOR 26493, APPLIED TO ALL EXPOSED SURFACES.
548 RESTORE CORROSION PROTECTION TO EDGES & SURFACES(E.G., HOLES

PRIMER, FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285
URETHANE COATING, COLOR 26493 OR TWO COATS OF URETHANE OR
OR TEFLON-URETHANE COATING OF THE COLOR SPECIFIED ON THE
APPLICABLE 16NXXXX AIRCRAFT PAINTING DRAWING (WHICHEVER WAS

MIL-P-23377E TYPE 1 CLASS 1, OR DEFT 44-GN-36 PRIMER,
FOLLOWED BY TWO COATS OF GRAY URETHANE COATING, COLOR
26493, PER MIL-C-83286 OR MIL-C-85285. FINISH HOLES (IN-
B - 46

Element
PRIMER, FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285
LIGHT SEMIGLOSS GRAY URETHANE COATING, COLOR 26493.

PER FPS-3001, PARA. 3.1.3(A) AND TOUCH UP WITH ONE COAT OF
FMS-3027, MIL-P-23377E TYPE 1 CLASS 1, OR DEFT 44-GN-36 PRIMER.

WITH ONE COAT OF FMS-3027, MIL-P-23377E TYPE 1 CLASS 1, OR
DEFT 44-GN-36 PRIMER, FOLLOWED BY THE FINISH SPECIFIED ON
THE APPLICABLE 16NXXXX AIRCRAFT PAINTING DWG. FINISH HOLES
553 APPLY TWO COATS OF FMS-3027, MIL-PRF-23377, OR

MIL-PRF-85582 PRIMER TO SPECIFIED SURFACE. APPLY THE COATS
TO THE BLIND HOLE BY FILLING WITH PRIMER AND DRAINING. THE
DELAY TIME BETWEEN COATS SHALL BE 120 MINUTES. THE PIN
SHALL REMAIN IN A POSITION TO ALLOW DRAINING THROUGHOUT THE
DELAY TIME AND FOLLOWING THE SECOND PRIME COAT APPLICATION.
AFTER CURE VISUALLY INSPECT FOR PRIMER COVERAGE. PRIMER
THICKNESS MEASUREMENTS ARE NOT REQUIRED. DRIPS AND RUNS
ARE ACCEPTABLE.
TOUCH UP ANY BARE AREAS BY SWABBING ADJACENT PRIME WITH
APPROVED SOLVENT FOLLOWED BY APPLICATION OF PRIMER BY
SWABBING BARE AREA AND OVERLAPPING ADJACENT PRIMER.

WHITE COLOR 17875 OR 17925, TO SPECIFIED AREA OF TUBING.
B - 47

Element
FOLLOWED BY TWO COATS OF MIL-C-83286 OR MIL-C-85285
LIGHT SEMIGLOSS GRAY URETHANE COATING, COLOR 26493.
B - 48

Mil Coating

Uploaded by

Copyright:

Available Formats

Mil Coating

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mil Coating

Uploaded by

Copyright:

Available Formats

LOCKHEED MARTIN REPORT NUMBER: 16PR070S

Aeronautics Company Date: 21 May 2003

FINISH CODES FOR

Releasability of this material under the Freedom of

Prepared By: Approved By:

Element/Code Reason for Change

APPENDIX A: FINISH CODE STEPS A-1

APPENDIX B: BASIC ELEMENTS B-1

FINISH CODES FOR F-16 AIR COMBAT FIGHTER

2 USE OF FINISH CODES

RATIONALE AND EXAMPLES OF FINISH CODE SELECTION

(2) FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer (2 coats).

The area of primer omission is specified on the drawing or in a general note.

A) FINISH EXTERIOR EXPOSED SURFACE AFTER ASSEMBLY PER DRAWING

EXAMPLE NO. 4 - Clad 2024-T81 Exterior Skin - Non-fuel area

3 REVISIONS AND CONTRACTUALITY

3.1 Formal revisions of Report 16PR070 will be in accordance with MIL-STD-480.

CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES

CROSS REFERENCED GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

CROSS REFERENCE GUIDE TO ALUMINUM ALLOY FINISH CODES (Cont'd)

CROSS REFERENCE GUIDE TO NON-CRES ALLOY STEEL FINISH CODES

ALLOY TENSILE STRENGTH

CROSS REFERENCE GUIDE TO NON-CRES ALLOY STEEL FINISH CODES (Cont'd)

ALLOY TENSILE STRENGTH

CROSS REFERENCE GUIDE TO CRES ALLOY FINISH CODES

CROSS REFERENCE GUIDE TO CRES ALLOY FINISH CODES (Cont'd)

CROSS REFERENCE GUIDE TO CRES ALLOY FINISH CODES (Cont'd)

4. "PRIMER" by itself refers to FMS-3027, MIL-PRF-23377, or MIL-PRF-85582 epoxy primer.

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes

APPENDIX A. Finish Codes