Callister Solutions of Ch07

CHAPTER 7
MECHANICAL PROPERTIES OF SOLIDS

PROBLEM SOLUTIONS
Concepts of Stress and Strain

7.1 (a) Equations 7.4a and 7.4b are expressions for normal () and shear () stresses, respectively, as a
function of the applied tensile stress () and the inclination angle of the plane on which these stresses are taken (
of Figure 7.4). Make a plot on which is presented the orientation parameters of these expressions (i.e., cos2 and
sin cos ) versus .
(b) From this plot, at what angle of inclination is the normal stress a maximum?
(c) Also, at what inclination angle is the shear stress a maximum?
Solution
(a) Below are plotted curves of cos2 (for ' ) and sin cos (for ') versus .
(b) The maximum normal stress occurs at an inclination angle of 0.

(c) The maximum shear stress occurs at an inclination angle of 45.
Excerpts from this work may be reproduced by instructors for distribution on a not-for-profit basis for testing or instructional purposes only to
students enrolled in courses for which the textbook has been adopted. Any other reproduction or translation of this work beyond that permitted
by Sections 107 or 108 of the 1976 United States Copyright Act without the permission of the copyright owner is unlawful.
Stress-Strain Behavior
7.2 A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa (30 106 psi) and an
original diameter of 10.2 mm (0.40 in.) will experience only elastic deformation when a tensile load of 8900 N
(2000 lbf) is applied. Compute the maximum length of the specimen before deformation if the maximum allowable
elongation is 0.25 mm (0.010 in.).
Solution
We are asked to compute the maximum length of a cylindrical nickel specimen (before deformation) that is
deformed elastically in tension. For a cylindrical specimen
d
A0 = 0
2
where d0 is the original diameter. Combining Equations 7.1, 7.2, and 7.5 and solving for l0 leads to
2
d
l E 0
2
l
l
l E
2 = l E d0
l0 =
= =
=
4F
F
E
A0
(0.41 103 m)(107 109 N / m 2 ) () (3.8 103 m)2

(4)(2000 N)
= 0.249 m = 249 mm
7.3 Consider a cylindrical nickel wire 1.5 mm in diameter and 3.2 104 mm long. Calculate its
elongation when a load of 330 N is applied. Assume that the deformation is totally elastic.
Solution
In order to compute the elongation of the Ni wire when the 330 N load is applied, we must employ
Equations 7.1, 7.2, and 7.5. Solving for l and realizing that for Ni, E = 207 GPa (Table 7.1),
l = l0 = l0
l0 F
=
=
E EA0
l0 F
d
E 0
2
(4)(32 m)(330 N)
9
(207 10
N / m 2 )( )(1.5 103 m)2
4l0 F
E d02
= 0.0289 m = 28.9 mm
7.4 For a brass alloy, the stress at which plastic deformation begins is 345 MPa, and the modulus of
elasticity is 103 GPa.
(a) What is the maximum load that may be applied to a specimen with a cross-sectional area of 131.6 mm2
without plastic deformation?
(b) If the original specimen length is 78 mm, what is the maximum length to which it may be stretched
without causing plastic deformation?
Solution
(a) This portion of the problem calls for a determination of the maximum load that can be applied without
plastic deformation (Fy). Taking the yield strength to be 345 MPa, and employment of Equation 7.1 leads to
Fy = y A0 = (345 106 N/m 2 )(131.6 10 6 m 2 )
= 45402 N
(b) The maximum length to which the sample may be deformed without plastic deformation is determined
from Equations 7.2 and 7.5 as
li = l0 1 +
E
345 MPa
= (76 mm) 1 +
= 76.25 mm (3.01 in.)
103 103 MPa
7.5 Consider a cylindrical specimen of a steel alloy 8.5 mm in diameter and 79 mm long that is pulled in
tension. Determine its elongation when a load of 68,360 N is applied. Tensile stress-strain behavior for an alloy
steel is shown in the Figure 7.33.
Solution
This problem asks that we calculate the elongation l of a specimen of steel the stress-strain behavior of
which is shown in the Figure. First it becomes necessary to compute the stress when a load of 68,360 N is applied
using Equation 7.1 as
F
=
A0
F
d
0
2
68,360 N
8.7 103 m
= 1205 MPa
Referring to the Figure, at this stress level we are in the elastic region on the stress-strain curve, which corresponds
to a strain of 0.0054. Now, utilization of Equation 7.2 to compute the value of l
l = l0 = (0.0054)(79 mm) = 0.4266 mm
7.6 In Section 2.6 it was noted that the net bonding energy EN between two isolated positive and negative
ions is a function of interionic distance r as follows:
EN =
A B
+
r rn
(7.30)
where A, B, and n are constants for the particular ion pair. Equation 7.30 is also valid for the bonding energy
between adjacent ions in solid materials. The modulus of elasticity E is proportional to the slope of the interionic
forceseparation curve at the equilibrium interionic separation; that is,
dF
E
dr r0
Derive an expression for the dependence of the modulus of elasticity on these A, B, and n parameters (for the twoion system) using the following procedure:
1. Establish a relationship for the force F as a function of r, realizing that
F=
dE N
dr
2. Now take the derivative dF/dr.

3. Develop an expression for r0, the equilibrium separation. Since r0 corresponds to the value of r at the
minimum of the EN-versus-r curve (Figure 2.8b), take the derivative dEN/dr, set it equal to zero, and solve for r,
which corresponds to r0.
4. Finally, substitute this expression for r0 into the relationship obtained by taking dF/dr.
Solution
This problem asks that we derive an expression for the dependence of the modulus of elasticity, E, on the
parameters A, B, and n in Equation 7.30. It is first necessary to take dEN /dr in order to obtain an expression for the
force F; this is accomplished as follows:
B
A
d n
d
dE N
r
=
+ r
F=
dr
dr
dr
A
r
nB
r
( n + 1)
The second step is to set this dEN /dr expression equal to zero and then solve for r (= r0). The algebra for this
procedure is carried out in Problem 2.9, with the result that
1/(1 n )
A
r0 =
nB
Next it becomes necessary to take the derivative of the force (dF/dr), which is accomplished as follows:
nB
A
d 2
d ( n + 1)
dF
= r + r
dr
dr
dr
2A
r
(n)(n + 1) B
r ( n + 2)
Now, substitution of the above expression for r0 into this equation yields
2A
(n)(n + 1) B
dF
+
=
3
/(1
n
)
( n + 2) /(1 n )
dr
r
A
A
0
nB
nB
which is the expression to which the modulus of elasticity is proportional.
7.7 Using the solution to Problem 7.6, rank the magnitudes of the moduli of elasticity for the following
hypothetical X, Y, and Z materials from the greatest to the least. The appropriate A, B, and n parameters (Equation
7.30) for these three materials are tabulated below; they yield EN in units of electron volts and r in nanometers:
Material
1.5
7.0 106
2.0
1.0 10
4.0 10
Y
Z
3.5
Solution
This problem asks that we rank the magnitudes of the moduli of elasticity of the three hypothetical metals
X, Y, and Z. From Problem 7.6, it was shown for materials in which the bonding energy is dependent on the
interatomic distance r according to Equation 7.30, that the modulus of elasticity E is proportional to
2A
A
nB
3 /(1 n )
(n)(n + 1) B
A
nB
( n + 2) /(1 n )
For metal X, A = 1.5, B = 7 10-6, and n = 8. Therefore,
(2)(1.5)
(8)
106
1.5
(7
3 /(1 8)
(8)(8 + 1) (7 106 )
1.5
6
(8) (7 10 )
(8 + 2) /(1 8)
= 830
For metal Y, A = 2.0, B = 1 105, and n = 9. Hence
(2)(2.0)
(9)
1 105
2.0
3 /(1 9)
(9)(9 + 1) (1 105 )
2.0
5
(9) (1 10 )
(9 + 2) /(1 9)
= 683
And, for metal Z, A = 3.5, B = 4 106, and n = 7. Thus
(2)(3.5)
(7)
106
3.5
(4
3 /(1 7)
(7)(7 + 1) (4 106 )
3.5
6
(7) (4 10 )
(7 + 2) /(1 7)
= 7425
Therefore, metal Z has the highest modulus of elasticity, followed by metal X, and then metal Y.
Elastic Properties of Materials

7.8 A cylindrical bar of steel (E = 207 Gpa, V = 0.30) 10 mm in diameter is to be deformed elastically by
application of a force along the bar axis. Using the data in Table 7.1, determine the force that will produce an
elastic reduction of 3.0 103 mm in the diameter.
Solution
This problem asks that we calculate the force necessary to produce a reduction in diameter of 3.0 103
mm for a cylindrical bar of steel. For a cylindrical specimen, the cross-sectional area is equal to
A0 =
d02
4
Now, combining Equations 7.1 and 7.5 leads to
F
F
=
= E z
A0
d02
4
And, since from Equation 7.8

d
x
d
d
z =
= 0 =
d 0
Substitution of this equation into the above expression gives

F
d02
d
= E
d 0
And, solving for F leads to
F=
d 0 d E
4
From Table 7.1, for steel, = 0.3 and E = 207 GPa. Thus,
F=
(10 103 m)( 3.0 106 m) () (207 109
N / m2 )
(4)(0.3)
= 16257.7 N
7.9 A cylindrical specimen of a hypothetical metal alloy is stressed in compression. If its original and
final diameters are 31.94 and 31.99 mm, respectively, and its final length is 103.99 mm, compute its original length
if the deformation is totally elastic. The elastic and shear moduli for this alloy are 65.5 and 25.4 GPa, respectively.
Solution
This problem asks that we compute the original length of a cylindrical specimen that is stressed in
compression. It is first convenient to compute the lateral strain x as
x =
d 31.99 mm 31.94 mm
=
= 1.57 103
d0
31.94 mm
In order to determine the longitudinal strain z we need Poisson's ratio, which may be computed using Equation 7.9;
solving for yields
E
65.5 103 MPa
1=
1 = 0.289
2G
(2) (25.4 103 MPa )
Now z may be computed from Equation 7.8 as
z =
x
1.33 103
=
= 5.42 103
0.289
Now solving for l0 using Equation 7.2,
l0 =
li
1 + z
103.99 mm
1 5.42 103
= 104.56 mm
7.10 A brass alloy is known to have a yield strength of 240 MPa, a tensile strength of 310 MPa, and an
elastic modulus of 110 GPa. A cylindrical specimen of this alloy 15.2 mm in diameter and 380 mm long is stressed in
tension and found to elongate 1.9 mm. On the basis of the information given, is it possible to compute the magnitude of
the load that is necessary to produce this change in length? If so, calculate the load. If not, explain why.
Solution
We are asked to ascertain whether or not it is possible to compute, for brass, the magnitude of the load
necessary to produce an elongation of 1.9 mm. It is first necessary to compute the strain at yielding from the yield
strength and the elastic modulus, and then the strain experienced by the test specimen. Then, if
(test) < (yield)
deformation is elastic, and the load may be computed using Equations 7.1 and 7.5. However, if
(test) > (yield)
computation of the load is not possible inasmuch as deformation is plastic and we have neither a stress-strain plot
nor a mathematical expression relating plastic stress and strain. We compute these two strain values as
(test) =
and
(yield) =
y
E
l 1.9 mm
=
= 0.005
l0 380 mm
240 MPa
110 103 MPa
= 0.0022
Therefore, computation of the load is not possible since (test) > (yield).
7.11 Consider the brass alloy for which the stressstrain behavior is shown in Figure 7.12. A cylindrical
specimen of this material 9.9 mm in diameter and 100.7 mm long is pulled in tension with a force of 9780 N. If it is
known that this alloy has a value for Poissons ratio of 0.35, compute (a) the specimen elongation, and (b) the
reduction in specimen diameter.
Solution
(a) This portion of the problem asks that we compute the elongation of the brass specimen. The first
calculation necessary is that of the applied stress using Equation 7.1, as
F
=
A0
F
d
0
2
9780 N
9.9 103 m
= 127 MPa
From the stress-strain plot in the Figure, this stress corresponds to a strain of about 1.5 103. From the definition
of strain, Equation 7.2
l = l0 = (1.5 103 ) (100.7 mm) = 0.151 mm
(b) In order to determine the reduction in diameter d, it is necessary to use Equation 7.8 and the
definition of lateral strain (i.e., x = d/d0) as follows
d = d0 x = d 0 z = (9.9 mm)(0.35) (1.5 103 )
= 5.20 10 3 mm
7.12 A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is to be subjected to a tensile load. If
the rod is to experience neither plastic deformation nor an elongation of more than 1.3 mm when the applied load is
29,000 N, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).
Material
Modulus of
Elasticity (GPa)
Yield Strength
(MPa)
Tensile Strength
(MPa)
Aluminum alloy
70
255
420
Brass alloy
100
345
420
Copper
110
210
210
Steel alloy
207
450
550
Solution
This problem asks that we ascertain which of four metal alloys will not (1) experience plastic deformation,
and (2) elongate more than 1.3 mm when a tensile load of 29,000 N is applied. It is first necessary to compute the
stress using Equation 7.1; a material to be used for this application must necessarily have a yield strength greater
than this value. Thus,
F
=
A0
29, 000 N
12.7 103 m
= 230 MPa
Of the metal alloys listed, aluminum, brass and steel have yield strengths greater than this stress.
Next, we must compute the elongation produced in aluminum, brass, and steel using Equations 7.2 and 7.5
in order to determine whether or not this elongation is less than 1.3 mm. For aluminum
l =
l0
(230 MPa)(500 mm)
=
= 1.64 mm
E
70 103 MPa
Thus, aluminum is not a candidate.

For brass
l =
l0
(230 MPa)(500 mm)
=
= 1.15 mm
E
100 103 MPa
Thus, brass is a candidate. And, for steel
l =
l0 (230 MPa)(500 mm)

=
= 0.56 mm
E
207 103 MPa
Therefore, of these four alloys, only brass and steel satisfy the stipulated criteria.
Tensile Properties
7.13 A cylindrical specimen of a brass alloy having a length of 103 mm must elongate only 5.15 mm when
a tensile load of 103,000 N is applied. Under these circumstances, what must be the radius of the specimen?
Consider this brass alloy to have the stressstrain behavior shown in Figure 7.12.
Solution
We are asked to calculate the radius of a cylindrical brass specimen in order to produce an elongation of
5.15 mm when a load of 103,000 N is applied. It first becomes necessary to compute the strain corresponding to
this elongation using Equation 7.2 as
l 5.15 mm
=
= 5.15 102
l0
100 mm
From Figure 7.12, a stress of 335 Mpa corresponds to this strain. Since for a cylindrical specimen, stress, force, and
initial radius r0 are related as
F
r02
then
r0 =
F
=
103, 000 N
(335 106 N / m 2 )
= 0.00989 m = 9.89 mm
7.14 A bar of a steel alloy that exhibits the stressstrain behavior shown in Figure 7.33 is subjected to a
tensile load; the specimen is 370 mm long and of square cross section 5.3 mm on a side.
(a) Compute the magnitude of the load necessary to produce an elongation of 2.22 mm.
(b) What will be the deformation after the load has been released?
Solution
(a) We are asked to compute the magnitude of the load necessary to produce an elongation of 2.22 mm for
the steel displaying the stress-strain behavior shown in the Figure. First, calculate the strain, and then the
corresponding stress from the plot.
l 2.22 mm
=
= 0.006
l0
370 mm
This is within the elastic region; from the inset of the Figure, this corresponds to a stress of about 1250 MPa. Now,
from Equation 7.1,
F = A0 = b 2
in which b is the cross-section side length. Thus,

F = (1250 106 N/m 2 ) (5.3 103 m)2 = 35,113 N
(b) After the load is released there will be no deformation since the material was strained only elastically.
7.15 A cylindrical specimen of stainless steel having a diameter of 12.8 mm and a gauge length of
50.800 mm is pulled in tension.
Use the loadelongation characteristics tabulated below to complete parts
(a) through (f).

Load
Length
mm
50.800
12,700
50.825
25,400
50.851
38,100
50.876
50,800
50.902
76,200
50.952
89,100
51.003
92,700
51.054
102,500
51.181
107,800
51.308
119,400
51.562
128,300
51.816
149,700
52.832
159,000
53.848
160,400
54.356
159,500
54.864
151,500
55.880
124,700
56.642
Fracture
(a) Plot the data as engineering stress versus engineering strain.

(b) Compute the modulus of elasticity.
(c) Determine the yield strength at a strain offset of 0.002.
(d) Determine the tensile strength of this alloy.
(e) What is the approximate ductility, in percent elongation?
(f) Compute the modulus of resilience.
Solution
This problem calls for us to make a stress-strain plot for stainless steel, given its tensile load-length data,
and then to determine some of its mechanical characteristics.
(a) The data are plotted below on two plots: the first corresponds to the entire stress-strain curve, while
for the second, the curve extends to just beyond the elastic region of deformation.
(b) The elastic modulus is the slope in the linear elastic region (Equation 7.10) as
E=
400 MPa 0 MPa

=
= 200 103 MPa = 200 GPa
0.002 0
(c) For the yield strength, the 0.002 strain offset line is drawn dashed. It intersects the stress-strain curve
at approximately 750 MPa.
(d) The tensile strength is approximately 1250 MPa, corresponding to the maximum stress on the complete
stress-strain plot.
(e) The ductility, in percent elongation, is just the plastic strain at fracture, multiplied by one-hundred.
The total fracture strain at fracture is 0.115; subtracting out the elastic strain (which is about 0.003) leaves a plastic
strain of 0.112. Thus, the ductility is about 11.2%EL.
(f) From Equation 7.14, the modulus of resilience is just
Ur =
2y
2E
which, using data computed above gives a value of
Ur =
(750 MPa)2
3
(2) (200 10 MPa )
= 1.40 106 J/m3
7.16 For the titanium alloy, whose stress strain behavior may be observed in the Tensile Tests module
of Virtual Materials Science and Engineering (VMSE), determine the following:
(a) the approximate yield strength (0.002 strain offset),
(b) the tensile strength, and
(c) the approximate ductility, in percent elongation.
How do these values compare with those for the two Ti-6Al-4V alloys presented in Table B.4 of Appendix B?
Solution
(a) It is possible to do a screen capture and then print out the entire stress-strain curve for the Ti alloy.
The intersection of a straight line parallel to the initial linear region of the curve and offset at a strain of 0.002 with
this curve is at approximately 720 MPa.
(b) The maximum reading in the stress window located below the plot as the curser point is dragged along
the stress-strain curve is 1000 MPa, the value of the tensile strength.
(c) The approximate percent elongation corresponds to the strain at fracture multiplied by 100 (i.e., 12%)
minus the maximum elastic strain (i.e., value of strain at which the linearity of the curve ends multiplied by 100in
this case about 0.5%); this gives a value of about 11.5%EL.
From Table B.4 in Appendix B, yield strength, tensile strength, and percent elongation values for the
anneal Ti-6Al-4V are 830 MPa, 900 MPa, and 14%EL, while for the solution heat treated and aged alloy, the
corresponding values are 1103 MPa, 1172 MPa, and 10%EL. Thus, tensile strength and percent elongation values
for the VMSE alloy are slightly lower than for the annealed material in Table B.4 (720 vs 830 MPa, and 11.5 vs. 14
%EL), whereas the tensile strength is slightly higher (1000 vs. 900 MPa).
7.17 Calculate the modulus of resilience for the materials having the stressstrain behaviors shown in
Figure 7.33.
Solution
This problem asks us to calculate the moduli of resilience for the materials having the stress-strain
behaviors shown in Figure 7.33. According to Equation 7.14, the modulus of resilience Ur is a function of the yield
strength and the modulus of elasticity as
Ur =
2y
2E
Values of the corresponding parameters for the steel alloy (Figure 7.21) are determined in Problem 7.24 as
1570 MPa (228,000 psi) and 210 GPa (30.5 106 psi), respectively, and therefore
Ur =
(1570 MPa)
3
(2) (210 10 MPa )
= 5.87 106 J/m3
7.18 A steel alloy to be used for a spring application must have a modulus of resilience of at least 2.07
MPa. What must be its minimum yield strength?
Solution
The modulus of resilience, yield strength, and elastic modulus of elasticity are related to one another
through Equation 7.14; the value of E for steel given in Table 7.1 is 207 GPa. Solving for y from this expression
yields
y =
2U r E =
(2) (2.07 MPa) (207 103 MPa )
= 925 MPa
True Stress and Strain

7.19 Demonstrate that Equation 7.16, the expression defining true strain, may also be represented by
A
T = ln 0
Ai
when specimen volume remains constant during deformation. Which of these two expressions is more valid during
necking? Why?
Solution
This problem asks us to demonstrate that true strain may also be represented by
A
T = ln 0
Ai
Rearrangement of Equation 7.17 leads to

li
A
= 0
l0
Ai
Thus, Equation 7.16 takes the form

l
A
T = ln i = ln 0
l0
Ai
A
The expression T = ln 0 is more valid during necking because Ai is taken as the area of the neck.
Ai
7.20 A tensile test is performed on a metal specimen, and it is found that a true plastic strain of 0.23 is
produced when a true stress of 571 MPa is applied; for the same metal, the value of K in Equation 7.19 is
860 MPa. Calculate the true strain that results from the application of a true stress of 600 MPa.
Solution
We are asked to compute the true strain that results from the application of a true stress of 600 MPa; other
true stress-strain data are also given. It first becomes necessary to solve for n in Equation 7.19. Taking logarithms
of this expression and after rearrangement we have
n=
log T log K
log T
log (571 MPa) log (860 MPa)

= 0.279
log (0.23)
Expressing T as the dependent variable (Equation 7.19), and then solving for its value from the data stipulated in
the problem statement, leads to
1/n

T = T
K
1/0.279
600 MPa
=
860 MPa
= 0.275
7.21 For a brass alloy, the following engineering stresses produce the corresponding plastic engineering
strains, prior to necking:
Engineering Stress
(MPa)
Engineering
Strain
315
0.105
340
0.220
On the basis of this information, compute the engineering stress necessary to produce an engineering strain of 0.28.
Solution
For this problem we first need to convert engineering stresses and strains to true stresses and strains so that
the constants K and n in Equation 7.19 may be determined. Since T = (1 + ) (Equation 7.18a) then,
T 1 = (315 MPa)(1 + 0.105) = 348 MPa
T 2 = (340 MPa)(1 + 0.220) = 415 MPa
Similarly for strains, since T = ln(1 + ) (Equation 7.18b) then

T 1 = ln (1 + 0.105) = 0.09985
T 2 = ln (1 + 0.220) = 0.19885
Taking logarithms of Equation 7.19, we get

log T = log K + n log T
which allows us to set up two simultaneous equations for the above pairs of true stresses and true strains, with K and
n as unknowns. Thus
log (348) = log K + n log (0.09985)
log (415) = log K + n log (0.19885)
Solving for these two expressions yields K = 628 MPa and n = 0.256.
Now, converting = 0.28 to true strain
T = ln (1 + 0.28) = 0.247
The corresponding T to give this value of T (using Equation 7.19) is just

T = K Tn = (628 MPa)(0.247)0.256 = 439 MPa
Now converting this value of T to an engineering stress using Equation 7.18a gives
=
T
439 MPa
=
= 343 MPa
1 + 1 + 0.28
7.22 Find the toughness (or energy to cause fracture) for a metal that experiences both elastic and plastic
deformation. Assume Equation 7.5 for elastic deformation, that the modulus of elasticity is 103 GPa (15 106 psi),
and that elastic deformation terminates at a strain of 0.007. For plastic deformation, assume that the relationship
between stress and strain is described by Equation 7.19, in which the values for K and n are 1520 MPa (221,000
psi) and 0.15, respectively. Furthermore, plastic deformation occurs between strain values of 0.007 and 0.60, at
which point fracture occurs.
Solution
This problem calls for us to compute the toughness (or energy to cause fracture). The easiest way to do
this is to integrate both elastic and plastic regions, and then add them together.
Toughness = d
0.007
0.60
E d +
E2
=
2
K n d
0.007
0.007
0.60
K
( n + 1)
+
(n + 1)
0.007
103 109 N / m 2
1520 106 N/ m 2
(0.007 ) 2 +
(0.60)1.15 (0.007)1.15
2
(1.0 + 0.15)
= 7.33 108 J/m3 (1.07 105 in.-lbf /in.3)
7.23 Taking the logarithm of both sides of Equation 7.19 yields

log T = log K + n log T
(7.32)
Thus, a plot of log T versus log T in the plastic region to the point of necking should yield a straight line having a
slope of n and an intercept (at log T = 0) of log K.
Using the appropriate data tabulated in Problem 7.15, make a plot of log T versus log T and determine
the values of n and K. It will be necessary to convert engineering stresses and strains to true stresses and strains
using Equations 7.18a and 7.18b.
Solution
This problem calls for us to utilize the appropriate data from Problem 7.15 in order to determine the values
of n and K for this material. From Equation 7.32 the slope and intercept of a log T versus log T plot will yield n
and log K, respectively. However, Equation 7.19 is only valid in the region of plastic deformation to the point of
necking; thus, only the 8th, 9th, 10th, 11th, 12th, and 13th data points may be utilized. The log-log plot with these
data points is given below.
The slope yields a value of 0.246 for n, whereas the intercept gives a value of 3.424 for log K, and thus K = 103.424
= 2655 MPa.
Elastic Recovery After Plastic Deformation

7.24 A steel alloy specimen having a rectangular cross section of dimensions 18.3 mm 3.0 mm has the
stressstrain behavior shown in Figure 7.33. If this specimen is subjected to a tensile force of 99,370 N then
(a) Determine the elastic and plastic strain values.
(b) If its original length is 610 mm, what will be its final length after the given strain is applied and then
released?
Solution
(a) We are asked to determine both the elastic and plastic strain values when a tensile force of 99,370 N is
applied to the steel specimen and then released. First it becomes necessary to determine the applied stress using
Equation 7.1; thus
=
F
F
=
A0 b0 d0
where b0 and d0 are cross-sectional width and depth (18.3 mm and 3.0 mm, respectively). Thus
99,370 N
(18.3
10
m)(3.0 103 m)
= 1.810 109 N / m 2 = 1810 MPa
From the Figure, this point is in the plastic region so the specimen will be both elastic and plastic strains. The total
strain at this point, t, is about 0.020. We are able to estimate the amount of permanent strain recovery e from
Hooke's law, Equation 7.5 as
e =
And, since E = 207 GPa for steel (Table 7.1),

e =
1810 MPa
207 103 MPa
= 0.0087
The value of the plastic strain, p is just the difference between the total and elastic strains; that is
p = t e = 0.020 0.0087 = 0.0113
(b) If the initial length is 610 mm then the final specimen length li may be determined from a rearranged
form of Equation 7.2 using the plastic strain value as
li = l0(1 + p) = (610 mm)(1 + 0.0113) = 616.7 mm
Flexural Strength (Ceramics)

7.25 A three-point bending test is performed on a spinel (MgAl2O4) specimen having a rectangular cross
section of height d = 3.8 mm and width b = 9 mm; the distance between support points is 25 mm.
(a) Compute the flexural strength if the load at fracture is 350 N.
(b) The point of maximum deflection y occurs at the center of the specimen and is described by
y =
FL3
48EI
where E is the modulus of elasticity and I is the cross-sectional moment of inertia. Compute y at a load of 310 N.
Solution
(a) For this portion of the problem we are asked to compute the flexural strength for a spinel specimen that
is subjected to a three-point bending test. The flexural strength (Equation 7.20a) is just
fs =
3F f L
2bd 2
for a rectangular cross-section. Using the values given in the problem statement,
fs =
(3)(350 N) (25 103 m)

(2)(9.0 103 m) (3.8 103 m)2
= 101 MPa
(b) We are now asked to compute the maximum deflection. From Table 7.1, the elastic modulus (E) for
spinel is 260 GPa. Also, the moment of inertia for a rectangular cross section (Figure 7.18) is just
I=
bd 3
12
Thus,
y =
FL3
FL3
=
bd 3 4 Ebd 3
48 E
12
(310 N) (25 103 m)3

(4) (260 109 N / m 2 )(9.0 103 m) (3.8 103 m)3
= 9.4 106 m = 9.4 103 mm
7.26 A three-point bending test was performed on an aluminum oxide specimen having a circular cross
section of radius 5.0 mm; the specimen fractured at a load of 3000 N when the distance between the support points
was 40 mm. Another test is to be performed on a specimen of this same material, but one that has a square cross
section of 15 mm length on each edge. At what load would you expect this specimen to fracture if the support point
separation is maintained at 40 mm?
Solution
It is first necessary to compute the flexural strength of the aluminum oxide, Equation 7.20b, and then,
using this value, we may calculate the value of Ff in Equation 7.20a. From Equation 7.20b
fs =
(3000 N) (40 103 m)

() (5.0 103 m)3
Ff L
R3
= 306 106 N/m 2 = 306 MPa
Now, solving for Ff from Equation 7.20a, realizing that b = d = 12 mm, yields
Ff =
2 fs d 3
3L
(2) (306 106 N / m 2 ) (15 103 m)3

(3) (40 103 m)
= 17, 200 N
Influence of Porosity on the Mechanical Properties of Ceramics

7.27 The modulus of elasticity for spinel (MgAl2O4) having 5 vol% porosity is 240 GPa.
(a) Compute the modulus of elasticity for the nonporous material.
(b) Compute the modulus of elasticity for 15 vol% porosity.
Solution
(a) This portion of the problem requests that we compute the modulus of elasticity for nonporous spinel
given that E = 240 GPa for a material having 5 vol% porosity. Thus, we solve Equation 7.21 for E0, using P = 0.05,
which gives
E0 =
E
1 1.9 P + 0.9 P 2
240 GPa
1 (1.9)(0.05) + (0.9)(0.05) 2
= 265 GPa
(b) Now we are asked to determine the value of E at P = 15 vol% (i.e., 0.15). Using Equation 7.21, we get
E = E0 (1 1.9P + 0.9P 2 )
= (265 GPa) 1 (1.9)(0.15) + (0.09)(0.15) 2 = 195 GPa
7.28 Using the data in Table 7.2, do the following:

(a) Determine the flexural strength for nonporous MgO assuming a value of 3.75 for n in Equation 7.22.
(b) Compute the volume fraction porosity at which the flexural strength for MgO is 74 MPa.
Solution
(a) This part of the problem asks us to determine the flexural strength of nonporous MgO assuming that
the value of n in Equation 7.22 is 3.75. Taking natural logarithms of both sides of Equation 7.22 yields
ln fs = ln 0 nP
In Table 7.2, it is noted that for P = 0.05, fs = 105 MPa. For the nonporous material P = 0 and, ln 0 = ln fffsss.
Solving for ln 0 from the above equation and using these data gives
ln 0 = ln fs + nP
= ln (105 MPa) + (3.75)(0.05) = 4.841

0 = e4.841 = 127 MPa
or
(b) Now we are asked to compute the volume percent porosity to yield a fs of 74 MPa. Taking the
natural logarithm of Equation 7.22 and solving for P leads to
P=
ln 0 ln fs
n
ln (127 MPa) ln (74 MPa)

3.75
= 0.144 or 14.4 vol%
Stress-Strain Behavior (Polymers)

7.29 From the stressstrain data for poly(methyl methacrylate) shown in Figure 7.24, determine the
modulus of elasticity and tensile strength at room temperature [20C], and compare these values with those given
in Tables 7.1 and 7.2.
Solution
From Figure 7.24, the elastic modulus is the slope in the elastic linear region of the 20C curve, which is
E=
(stress) 30 MPa 0 MPa

=
= 3.3 GPa
(strain)
9 103 0
The value range cited in Table 7.1 is 2.24 to 3.24 GPa. Thus, the plotted value is a little on the high side.
The tensile strength corresponds to the stress at which the curve ends, which is 52 MPa. This value lies
within the range cited in Table 7.248.3 to 72.4 MPa.
7.30 For the high-density polyethylene polymer, whose stress strain behavior may be observed in the
Tensile Tests module of Virtual Materials Science and Engineering (VMSE), determine the following:
(a) the yield strength,
(b) the tensile strength, and
(c) the approximate ductility, in percent elongation.
How do these values compare with those for the high-density polyethylene material presented in Table 7.2?
Solution
(a) The yield strength of this polymeric material corresponds to the maximum of the stress-strain curve
just past the termination of the elastic region. The reading in the stress window as the curser is located at this point
is 19 MPa. This value is significantly lower than the range of values cited in Table 7.2: 26.2 to 33.1 MPa.
(b) The stress at which fracture occurs corresponds to the tensile strength. This reading in the stress
window is 12.2 MPa, which, again, is significantly lower than the value ranged presented in Table 7.2: 22.1 to 31.0
MPa.
(c) The approximate percent elongation corresponds to the strain at fracture multiplied by 100. The
reading in the strain window at fracture is 6.34, which corresponds to 634 %EL. This value is well within the range
cited in Table 7.2: 10 to 1200 %EL.
Viscoelastic Deformation
7.31 In Figure 7.34, the logarithm of Er(t) versus the logarithm of time is plotted for PMMA at a variety of
temperatures. Make a plot of log Er(10) versus temperature and then estimate its Tg.
Solution
Below is plotted the logarithm of Er(10) versus temperature.
The glass-transition temperature is that temperature corresponding to the abrupt decrease in log Er(10), which for
this PMMA material is about 115C.
7.32 On the basis of the curves in Figure 7.26, sketch schematic straintime plots for the following
polystyrene materials at the specified temperatures:
(a) Crystalline at 70C
(b) Amorphous at 180C
(c) Crosslinked at 180C
(d) Amorphous at 100C
Solution
(a) Crystalline polystyrene at 70C behaves in a glassy manner (Figure 7.29, curve A); therefore, the
strain-time behavior would be as Figure 7.26(b).
(b) Amorphous polystyrene at 180C behaves as a viscous liquid (Figure 7.29, curve C); therefore, the
strain-time behavior will be as Figure 7.26(d).
(c) Crosslinked polystyrene at 180C behaves as a rubbery material (Figure 7.29, curve B); therefore, the
strain-time behavior will be as Figure 7.26(c).
(d) Amorphous polystyrene at 100C behaves as a leathery material (Figure 7.28); therefore, the straintime behavior will be as Figure 7.26(c).
7.33
Make two schematic plots of the logarithm of relaxation modulus versus temperature for an
amorphous polymer (curve C in Figure 7.29).

(a) On one of these plots demonstrate how the behavior changes with increasing molecular weight.
(b) On the other plot, indicate the change in behavior with increasing crosslinking.
Solution
(a) This portion of the problem calls for a plot of log Er(10) versus temperature demonstrating how the
behavior changes with increased molecular weight. Such a plot is given below. Increasing molecular weight
increases both glass-transition and melting temperatures.
(b) We are now called upon to make a plot of log Er(10) versus temperature demonstrating how the
behavior changes with increased crosslinking. Such a plot is given below. Increasing the degree of crosslinking
will increase the modulus in both glassy and rubbery regions.
Hardness
7.34 (a) A 10.3 mm-diameter Brinell hardness indenter produced an indentation 2.6 mm in diameter in a
steel alloy when a load of 1100 kg was used. Compute the HB of this material.
(b) What will be the diameter of an indentation to yield a hardness of 280 HB when a 520-kg load is used?
Solution
(a) We are asked to compute the Brinell hardness for the given indentation. It is necessary to use the
equation in Table 7.5 for HB, where P = 1100 kg, d = 2.6 mm, and D = 10.3 mm. Thus, the Brinell hardness is
computed as
HB =
2P
D D
D2 d 2
(2)(1100 kg)
()(10.3 mm) 10.3 mm
(10.3 mm)2 (2.6 mm) 2
= 203.8
(b) This part of the problem calls for us to determine the indentation diameter d which will yield a 280 HB
when P = 520 kg. Solving for d from the equation in Table 7.5 gives
d =
2P
D D
(HB) D
(2)(520 kg)
(10.3 mm) 10.3 mm
= 1.53 mm
(280)()(10.3 mm)
7.35 Using the data represented in Figure 7.31, specify equations relating tensile strength and Brinell
hardness for brass and nodular cast iron, similar to Equations 7.25a and 7.25b for steels.
Solution
These equations, for a straight line, are of the form
TS = C + (E)(HB)
where TS is the tensile strength, HB is the Brinell hardness, and C and E are constants, which need to be
determined.
One way to solve for C and E is analytically--establishing two equations using TS and HB data points on
the plot, as
(TS)1 = C + (E)(BH)1
(TS)2 = C + (E)(BH)2
Solving for E from these two expressions yields
E=
(TS )1 (TS ) 2
(HB) 2 (HB)1
For nodular cast iron, if we make the arbitrary choice of (HB)1 and (HB)2 as 200 and 300, respectively, then, from
Figure 7.31, (TS)1 and (TS)2 take on values of 600 MPa and 1100 MPa, respectively. Substituting these values into
the above expression and solving for E gives
E=
600 MPa 1100 MPa

= 5.0 MPa/HB
200 HB 300 HB
Now, solving for C yields

C = (TS)1 (E)(BH)1
= 600 MPa (5.0 MPa/HB)(200 HB) = 400 MPa
Thus, for nodular cast iron, these two equations take the form
TS(MPa) = 400 + 5.0 HB
TS(psi) = 59,000 + 730 HB
Now for brass, we take (HB)1 and (HB)2 as 100 and 200, respectively, then, from Figure 7.31, (TS)1 and
(TS)2 take on values of 370 MPa and 660 MPa, respectively. Substituting these values into the above expression
and solving for E gives
E=
370 MPa 660 MPa

= 2.9 MPa/HB
100 HB 200 HB
Now, solving for C yields

C = (TS)1 (E)(BH)1
= 370 MPa (2.9 MPa/HB)(100 HB) = 80 MPa
Thus, for brass these two equations take the form
TS(MPa) = 80 + 2.9 HB
TS(psi) = 13,000 + 410 HB
Variability of Material Properties

7.36 Below are tabulated a number of Rockwell G hardness values that were measured on a single steel
specimen. Compute the average and standard deviation hardness values.
49.7
49.1
49.2
49.2
48.2
48.6
47.0
49.7
47.2
49.8
48.3
48.0
Solution
The average of the given hardness values is calculated using Equation 7.26 as
18
HRGi
HRG =
i=1
18
49.7 + 49.1 + 49.2 + " + 48.0

= 48.67
12
And we compute the standard deviation using Equation 7.27 as follows:

18
( HRGi HRG )
i =1
s=
12 1
1/2
( 49.7 48.7)2 + (49.1 48.7) 2 + " + (48.0 48.7)2

=
11
10.12
= 0.959
11
Design/Safety Factors
7.37 Determine working stress for the alloy that have the stressstrain behaviors shown in Figure 7.12,
assuming a factor of safety of 2.
Solution
The working stress for the alloy the stress-strain behavior of which is shown in the Figure is calculated by
dividing the yield strength by a factor of safety, which we will take to be 2. For the alloy, since y = 250 MPa, the
working stress is 125 MPa.
DESIGN PROBLEMS
7.D1 (a) Gaseous hydrogen at a constant pressure of 0.658 MPa is to flow within the inside of a thinwalled cylindrical tube of nickel that has a radius of 0.125 m. The temperature of the tube is to be 350C and the
pressure of hydrogen outside of the tube will be maintained at 0.0127 MPa. Calculate the minimum wall thickness
if the diffusion flux is to be no greater than 1.25 107 mol/m2-s. The concentration of hydrogen in the nickel, CH
(in moles hydrogen per m3 of Ni) is a function of hydrogen pressure, PH2 (in MPa) and absolute temperature (T)
according to
12.3 kJ / mol
CH = 30.8 pH 2 exp
RT
(7.34)
Furthermore, the diffusion coefficient for the diffusion of H in Ni depends on temperature as

39.56 kJ / mol
DH (m 2 / s) = 4.76 107 exp
RT
(7.35)
(b) For thin-walled cylindrical tubes that are pressurized, the circumferential stress is a function of the
pressure difference across the wall (p), cylinder radius (r), and tube thickness (x) as
=
r p
4x
(7.36)
Compute the circumferential stress to which the walls of this pressurized cylinder are exposed.
(c) The room-temperature yield strength of Ni is 100 MPa and, furthermore, y diminishes about 5 MPa
for every 50C rise in temperature. Would you expect the wall thickness computed in part (b) to be suitable for this
Ni cylinder at 350C? Why or why not?
(d) If this thickness is found to be suitable, compute the minimum thickness that could be used without any
deformation of the tube walls. How much would the diffusion flux increase with this reduction in thickness? On the
other hand, if the thickness determined in part (c) is found to be unsuitable, then specify a minimum thickness that
you would use. In this case, how much of a diminishment in diffusion flux would result?
Solution
(a) This portion of the problem asks for us to compute the wall thickness of a thin-walled cylindrical Ni
tube at 350C through which hydrogen gas diffuses. The inside and outside pressures are, respectively, 0.658 and
0.0127 MPa, and the diffusion flux is to be no greater than 1.25 107 mol/m2-s. This is a steady-state diffusion
problem, which necessitates that we employ Equation 6.3. The concentrations at the inside and outside wall faces
may be determined using Equation 7.34, and, furthermore, the diffusion coefficient is computed using Equation
7.35. Solving for x (using Equation 6.3)
x =
(4.76
D C
J
1
1.25 10
mol / m 2 s
39,560 J / mol
107 ) exp

(8.31 J / mol-K)(350 + 273 K)
12,300 J / mol
(30.8) exp
(8.31 J / mol-K)(350 + 273 K)
0.0127 MPa
0.658 MPa
= 0.00366 m = 3.66 mm
(b) Now we are asked to determine the circumferential stress:
=
r p
4 x
(0.125 m)(0.658 MPa 0.0127 MPa)

(4)(0.00366 m)
= 5.50 MPa
(c) Now we are to compare this value of stress to the yield strength of Ni at 350C, from which it is
possible to determine whether or not the 3.66 mm wall thickness is suitable. From the information given in the
problem statement, we may write an equation for the dependence of yield strength (y) on temperature (T ) as
follows:
y = 100 MPa
5 MPa
(T Tr )
50C
where Tr is room temperature and for temperature in degrees Celsius. Thus, at 350C
y = 100 MPa 0.1 MPa/ C (350C 20C) = 67 MPa
Inasmuch as the circumferential stress (5.50 MPa) is much less than the yield strength (67 MPa), this thickness is
entirely suitable.
(d) And, finally, this part of the problem asks that we specify how much this thickness may be reduced and
still retain a safe design. Let us use a working stress by dividing the yield stress by a factor of safety, according to
Equation 7.29. On the basis of our experience, let us use a value of 2.0 for N. Thus
w =
y
N
67 MPa
= 33.5 MPa
2
Using this value for w and Equation 7.36, we now compute the tube thickness as
x =
r p
4 w
(0.125 m)(0.658 MPa 0.0127 MPa)

4(33.5 MPa)
= 0.00060 m = 0.60 mm
Substitution of this value into Ficks first law we calculate the diffusion flux as follows:
J = D
C
x
39,560 J / mol
= (4.76 107 ) exp

(8.31 J / mol-K)(350 + 273 K)
12,300 J / mol
(30.8) exp
(8.31 J / mol-K)(350 + 273 K)

0.0006 m
0.0127 MPa
0.658 MPa
= 7.62 107 mol/m2-s

Thus, the flux increases by approximately a factor of 6, from 1.25 107 to 7.62 107 mol/m2-s with this
reduction in thickness.
7.D2 Consider the steady-state diffusion of hydrogen through the walls of a cylindrical nickel tube as
described in Problem 7.D1. One design calls for a diffusion flux of 2.5 108 mol/m2-s, a tube radius of 0.100 m,
and inside and outside pressures of 1.015 MPa and 0.01015 MPa, respectively; the maximum allowable
temperature is 300C. Specify a suitable temperature and wall thickness to give this diffusion flux and yet ensure
that the tube walls will not experience any permanent deformation.
Solution
There are probably several different approaches that may be used; and, of course, there is not one unique
solution. Let us employ the following procedure to solve this problem: (1) assume some wall thickness, and, then,
using Fick's first law for diffusion (which also employs Equations 6.3 and 7.35), compute the temperature at which
the diffusion flux is that required; (2) compute the yield strength of the nickel at this temperature using the
dependence of yield strength on temperature as stated in Problem 7.D1; (3) calculate the circumferential stress on
the tube walls using Equation 7.36; and (4) compare the yield strength and circumferential stress values--the yield
strength should probably be at least twice the stress in order to make certain that no permanent deformation occurs.
If this condition is not met then another iteration of the procedure should be conducted with a more educated choice
of wall thickness.
As a starting point, let us arbitrarily choose a wall thickness of 2 mm (2 103 m). The steady-state
diffusion equation, Equation 6.3, takes the form
J = D
C
x
= 2.5 108 mol/m2-s
39,560 J / mol
= (4.76 107 ) exp

(8.31 J / mol-K)(T )
12,300 J / mol
(30.8) exp
0.01015 MPa 1.015 MPa
(8.31
J / mol-K)(T )
0.002 m
Solving this expression for the temperature T gives T = 500 K = 227C; this value is satisfactory inasmuch as it is
less than the maximum allowable value (300C).
The next step is to compute the stress on the wall using Equation 7.36; thus
=
r p
4 x
(0.100 m)(1.015 MPa 0.01015 MPa)

(4) (2 103 m)
= 12.6 MPa
Now, the yield strength (y) of Ni at this temperature may be computed using the expression
y = 100 MPa
5 MPa
(T Tr )
50C
where Tr is room temperature. Thus,

y = 100 MPa 0.1 MPa/C (227C 20C) = 79.3 MPa
Inasmuch as this yield strength is greater than twice the circumferential stress, wall thickness and temperature
values of 2 mm and 227C are satisfactory design parameters.

Callister Solutions of Ch07

Uploaded by

Copyright:

Available Formats

Callister Solutions of Ch07

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Callister Solutions of Ch07

Uploaded by

Copyright:

Available Formats

CHAPTER 7

MECHANICAL PROPERTIES OF SOLIDS

Concepts of Stress and Strain

(b) The maximum normal stress occurs at an inclination angle of 0.

(0.41 103 m)(107 109 N / m 2 ) () (3.8 103 m)2

N / m 2 )( )(1.5 103 m)2

Fy = y A0 = (345 106 N/m 2 )(131.6 10 6 m 2 )

2. Now take the derivative dF/dr.

which is the expression to which the modulus of elasticity is proportional.

For metal X, A = 1.5, B = 7 10-6, and n = 8. Therefore,

And, for metal Z, A = 3.5, B = 4 106, and n = 7. Thus

Elastic Properties of Materials

Now, combining Equations 7.1 and 7.5 leads to

And, since from Equation 7.8

Substitution of this equation into the above expression gives

And, solving for F leads to

(10 103 m)( 3.0 106 m) () (207 109

Now z may be computed from Equation 7.8 as

Now solving for l0 using Equation 7.2,

Thus, aluminum is not a candidate.

Thus, brass is a candidate. And, for steel

l0 (230 MPa)(500 mm)

in which b is the cross-section side length. Thus,

Use the loadelongation characteristics tabulated below to complete parts

(a) through (f).

(a) Plot the data as engineering stress versus engineering strain.

400 MPa 0 MPa

which, using data computed above gives a value of

(2) (200 10 MPa )

= 1.40 106 J/m3

(2) (210 10 MPa )

= 5.87 106 J/m3

(2) (2.07 MPa) (207 103 MPa )

True Stress and Strain

Rearrangement of Equation 7.17 leads to

Thus, Equation 7.16 takes the form

log (571 MPa) log (860 MPa)

Similarly for strains, since T = ln(1 + ) (Equation 7.18b) then

Taking logarithms of Equation 7.19, we get

The corresponding T to give this value of T (using Equation 7.19) is just

= 7.33 108 J/m3 (1.07 105 in.-lbf /in.3)

7.23 Taking the logarithm of both sides of Equation 7.19 yields

Elastic Recovery After Plastic Deformation

= 1.810 109 N / m 2 = 1810 MPa

And, since E = 207 GPa for steel (Table 7.1),

Flexural Strength (Ceramics)

(3)(350 N) (25 103 m)

(310 N) (25 103 m)3

= 9.4 106 m = 9.4 103 mm

(3000 N) (40 103 m)

= 306 106 N/m 2 = 306 MPa

(2) (306 106 N / m 2 ) (15 103 m)3

Influence of Porosity on the Mechanical Properties of Ceramics

7.28 Using the data in Table 7.2, do the following:

= ln (105 MPa) + (3.75)(0.05) = 4.841

ln (127 MPa) ln (74 MPa)

= 0.144 or 14.4 vol%

Stress-Strain Behavior (Polymers)

(stress) 30 MPa 0 MPa

amorphous polymer (curve C in Figure 7.29).