Scribd
Upload
110 views

Mindwave Mobile Arduino Sample Code

This Arduino code summarizes an interface between an Arduino and a Mindwave headset to read brainwave data via Bluetooth. It defines pin assignments for LEDs, reads raw brainwave data from the Mindwave via serial, parses the data stream, and indicates the attention level via a LED bar graph display. It also outputs the attention and signal quality levels through the serial monitor.

Uploaded by

Diego Pineda
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
110 views

Mindwave Mobile Arduino Sample Code

This Arduino code summarizes an interface between an Arduino and a Mindwave headset to read brainwave data via Bluetooth. It defines pin assignments for LEDs, reads raw brainwave data from the Mindwave via serial, parses the data stream, and indicates the attention level via a LED bar graph display. It also outputs the attention and signal quality levels through the serial monitor.

Uploaded by

Diego Pineda
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 8

////////////////////////////////////////////////////////////////////////

// Arduino Bluetooth Interface with Mindwave


//
// This is example code provided by NeuroSky, Inc. and is provided
// license free.
////////////////////////////////////////////////////////////////////////
#define LED 13
#define BAUDRATE 57600
#define DEBUGOUTPUT 0
#define GREENLED1 3
#define GREENLED2 4
#define GREENLED3 5
#define YELLOWLED1 6
#define YELLOWLED2 7
#define YELLOWLED3 8
#define YELLOWLED4 9
#define REDLED1 10
#define REDLED2 11
#define REDLED3 12
#define powercontrol 10
// checksum variables
byte generatedChecksum = 0;
byte checksum = 0;
int payloadLength = 0;
byte payloadData[64] = {
0};
byte poorQuality = 0;
byte attention = 0;
byte meditation = 0;
// system variables
long lastReceivedPacket = 0;
boolean bigPacket = false;

//////////////////////////
// Microprocessor Setup //
//////////////////////////
void setup() {
pinMode(GREENLED1, OUTPUT);
pinMode(GREENLED2, OUTPUT);
pinMode(GREENLED3, OUTPUT);
pinMode(YELLOWLED1, OUTPUT);
pinMode(YELLOWLED2, OUTPUT);
pinMode(YELLOWLED3, OUTPUT);
pinMode(YELLOWLED4, OUTPUT);
pinMode(REDLED1, OUTPUT);
pinMode(REDLED2, OUTPUT);
pinMode(REDLED3, OUTPUT);
pinMode(LED, OUTPUT);
Serial.begin(BAUDRATE);

// USB

}
////////////////////////////////
// Read data from Serial UART //
////////////////////////////////
byte ReadOneByte() {
int ByteRead;
while(!Serial.available());
ByteRead = Serial.read();
#if DEBUGOUTPUT
Serial.print((char)ByteRead); // echo the same byte out the USB serial (for debug
purposes)
#endif
return ByteRead;
}
/////////////

//MAIN LOOP//
/////////////
void loop() {
// Look for sync bytes
if(ReadOneByte() == 170) {
if(ReadOneByte() == 170) {
payloadLength = ReadOneByte();
if(payloadLength > 169)
return;

//Payload length can not be greater than 169

generatedChecksum = 0;
for(int i = 0; i < payloadLength; i++) {
payloadData[i] = ReadOneByte();
//Read payload into memory
generatedChecksum += payloadData[i];
}
checksum = ReadOneByte();
//Read checksum byte from stream
generatedChecksum = 255 - generatedChecksum; //Take one's compliment of
generated checksum
if(checksum == generatedChecksum) {
poorQuality = 200;
attention = 0;
meditation = 0;
for(int i = 0; i < payloadLength; i++) {
switch (payloadData[i]) {
case 2:
i++;
poorQuality = payloadData[i];
bigPacket = true;
break;
case 4:
i++;
attention = payloadData[i];

// Parse the payload

break;
case 5:
i++;
meditation = payloadData[i];
break;
case 0x80:
i = i + 3;
break;
case 0x83:
i = i + 25;
break;
default:
break;
} // switch
} // for loop
#if !DEBUGOUTPUT
// *** Add your code here ***
if(bigPacket) {
if(poorQuality == 0)
digitalWrite(LED, HIGH);
else
digitalWrite(LED, LOW);
Serial.print("PoorQuality: ");
Serial.print(poorQuality, DEC);
Serial.print(" Attention: ");
Serial.print(attention, DEC);
Serial.print(" Time since last packet: ");
Serial.print(millis() - lastReceivedPacket, DEC);
lastReceivedPacket = millis();
Serial.print("\n");
switch(attention / 10) {
case 0:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, LOW);

digitalWrite(GREENLED3, LOW);
digitalWrite(YELLOWLED1, LOW);
digitalWrite(YELLOWLED2, LOW);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 1:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, LOW);
digitalWrite(YELLOWLED1, LOW);
digitalWrite(YELLOWLED2, LOW);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 2:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, LOW);
digitalWrite(YELLOWLED2, LOW);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 3:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);

digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, LOW);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 4:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 5:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 6:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);

digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 7:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, HIGH);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 8:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, HIGH);
digitalWrite(REDLED2, HIGH);
digitalWrite(REDLED3, LOW);
break;
case 9:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);

digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, HIGH);
digitalWrite(REDLED2, HIGH);
digitalWrite(REDLED3, HIGH);
break;
case 10:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, HIGH);
digitalWrite(REDLED2, HIGH);
digitalWrite(REDLED3, HIGH);
break;
}
}
#endif
bigPacket = false;
}
else {
// Checksum Error
} // end if else for checksum
} // end if read 0xAA byte
} // end if read 0xAA byte
}

You might also like