Scribd
Upload
141 views11 pages

CREO 2 Parametric

This document outlines 35 practical exercises to be performed in Creo Parametric. The practicals involve modeling and assembling various mechanical components like cotter joints, knuckle joints, screw jacks, plummer blocks, flange couplings, cams and followers, Oldham couplings, slider crank mechanisms, gears, springs, fans, bolts and nuts, impellers, and chain drives. Additionally, simulations will be performed on components like cam followers, slider crank mechanisms, Oldham couplings, gear trains, planetary gear trains, beams, mass spring damper systems.

Uploaded by

Dipankar borah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
141 views11 pages

CREO 2 Parametric

This document outlines 35 practical exercises to be performed in Creo Parametric. The practicals involve modeling and assembling various mechanical components like cotter joints, knuckle joints, screw jacks, plummer blocks, flange couplings, cams and followers, Oldham couplings, slider crank mechanisms, gears, springs, fans, bolts and nuts, impellers, and chain drives. Additionally, simulations will be performed on components like cam followers, slider crank mechanisms, Oldham couplings, gear trains, planetary gear trains, beams, mass spring damper systems.

Uploaded by

Dipankar borah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 11

Page 1 of 11

CREO 2.0 LIST OF PRACTICALS TO BE


PERFORMED

practical1.

Introduction and revision of modelling tools to be


used in creo parametric

Practical 2.
joint.

Modelling of different components of the cotter

Page 2 of 11

PRACTICAL 3.

Assembly of different components of the

COTTER joint.

PRACTICAL 4. Modelling of different components of the


KNUCKLE JOINT

Practical 5 . Assembly of different components of the


KNUCKLE JOINT

Practical 6.
jack.

Modelling the different components of the screw

Page 3 of 11

Practical 7.

Assembly of the different components of the

screw jack

Practical 8.

Modelling the different components of the


PLUMMER BLOCK

Page 4 of 11

Practical 9. Assembly

of the different components of the

PLUMMER BLOCK.

Practical 10. Modelling the different components of the


FLANGE COUPLING

Practical 11.

Assembly of the different components of the


FLANGE COUPLING.

Page 5 of 11

Practical 12.

Modelling the different components of the

cam and follower.

Practical 13.

Assembly of the different components of the

cam and follower

Practical 14. Modelling the different components of the


Oldham coupling

Practical 15.
Oldham coupling

Assembly of the different components of the

Page 6 of 11

Practical 16.

Modelling the different components of the


slider crank mechanism

Practical 17.

Assembly of the different components of the


slider crank mechanism

Practical 18.

Modelling the different components of the

spur gear

Practical 19. Assembly of the different components of the


gear train

Page 7 of 11

Practical 20.

Use of helical sweep command to construct

springs

Practical 21. Use of revolve command to construct objects.

Page 8 of 11

Practical 22.

Modelling the different components of a fan

Practical 23.

To create a bolt and nut assembly using creo

Page 9 of 11

Practical 24.

To make an impeller using creo

Practical 25.

Simulation of cam follower arrangement.

Practical 26.

Simulation of the slider crank mechanism

Practical 27.

Simulation of the Oldham coupling

mechanism

Practical 28.

Simulation of the gear train.

Practical 29.

Simulation of planetary gear train.

Page 10 of 11

Practical 30.

Mechanical analysis of beam in creo

Practical 31.Mechanical

analysis of cam and follower

movement

Practical 32. Direct modelling of chain drive and its


sprockets

Page 11 of 11

Practical 33.

Simulation of chain drive and its sprockets

Practical 34.

Modelling damper system of a mass spring

damper system

Practical 35.

Simulation of a mass spring damper system

You might also like