Scribd
Upload
94 views

Nid Mounting Detail Camera Lowering Pole: 10 FT X 10 FT X

This document provides details for installing a camera lowering pole, including: 1. It shows the pole foundation and grounding requirements, with ground rods connected to the pole and junction box. 2. Flexible conduits are used to pass communication and power cables through the pole. 3. At the top, a poletop junction box is mounted along with a camera lowering system, dome assembly, and mounting brackets.

Uploaded by

HOFFER
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
94 views

Nid Mounting Detail Camera Lowering Pole: 10 FT X 10 FT X

This document provides details for installing a camera lowering pole, including: 1. It shows the pole foundation and grounding requirements, with ground rods connected to the pole and junction box. 2. Flexible conduits are used to pass communication and power cables through the pole. 3. At the top, a poletop junction box is mounted along with a camera lowering system, dome assembly, and mounting brackets.

Uploaded by

HOFFER
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

INTO POLE

STATE FURNISHED
LOWERING POLE

NID CABLE

HAND HOLE

4
0"

GROUNDING LUG
BOND GROUND
WIRE TO LUG

M AX.

(2) 2 INCH FLEXIBLE


STAINLESS STEEL
CONDUIT WITH
COMPRESSION
FITTING

COMMUNICATION
CABLES
HAND HOLE

POWER
GROUNDING LUG

CONDUCTORS

BOND GROUND

POWER

STATE FURNISHED

WIRE TO LUG

CONDUCTORS

ANCHOR BOLTS

STATE FURNISHED

NOTES:
1.

DGN File:L:
\Standard_Drawings\Imperial\2012Approved\_Supplemental_Issues\Supp7Approved\AT11A.
dgn

ANCHOR BOLTS
TYPE II-PC

TYPE II-PC
JUNCTION BOX
SEE STD DWG

SEE NOTE 1

AT 12 FOR
FOUNDATION

BOND GROUND WIRE TO

DETAILS

GROUND ROD INSIDE

JUNCTION BOX

SEE STD DWG


FOUNDATION

BOND GROUND WIRE TO

DETAILS

SUPPLY GROUNDING
10 FT

3
x4

2.

REFER TO STD DWG AT 10A, 10B, AND 10C FOR CAMERA MOUNTING
DETAILS.

3.

USE POLE MOUNTED CABINET UNLESS PAD MOUNTED ATMS


CABINET IS CALLED FOR ON PLANS.

GROUND ROD INSIDE


JUNCTION BOX TO

JUNCTION BOX TO
(3)-2 INCH CONDUITS

CABINET. REFER TO STD DWG AT 7 FOR JUNCTION BOX DETAILS.

SEE NOTE 1

AT 12 FOR

JUNCTION BOX REQUIRED UNLESS POLE IS WITHIN 20 OF CONTROL

(3)-2 INCH CONDUITS

SUPPLY GROUNDING
10 FT

INCH COPPER COATED

3
x4

INCH COPPER

STEEL GROUND ROD CONNECT

COATED STEEL GROUND ROD

TO DISCONNECT AND SUPPLY

CONNECTED TO POLE

GROUND

AND SUPPLY GROUNDING

4.

LOWERING CABLE MUST NOT CONTACT ANY OTHER CABLE.

5.

DO NOT MOUNT DOME CAMERAS ON LUMINAIRE POLES.

6.

MOUNT NID TO NOT INTERFERE WITH CAMERA LOWERING

#6 BARE COPPER

DISTANCE AWAY FROM THE TRAVELED WAY, OR SHIELD

GROUND WIRE

GROUND WIRE

ACCORDING TO THE CURRENT EDITION OF THE ROADSIDE

CAMERA LOWERING POLE DETAIL

NON-LOWERING CCTV POLE DETAIL

REM ARKS

DATE

LOCATE POLE A MINIMUM OF 1.2 TIMES THE AASHTO CLEAR ZONE

#6 BARE COPPER

DESIGN GUIDE.

8.

CABINET MUST NOT INTERFERE WITH CAMERA LOWERING


OPERATION.

9.

ERECT CAMERA LOWERING POLE WITH HAND HOLE ON


DOWN STREAM TRAFFIC SIDE OF POLE.

10. DO NOT INSTALL CAMERA LOWERING SYSTEM OR NID ON


SAME SIDE OF POLE AS HAND HOLE.
11. ALL CONDUIT ENTRY MUST BE THROUGH BOTTOM OF CABINET.
12. ALL FLEXIBLE STEEL CONDUIT MUST BE INTENDED FOR
OUTDOOR APPLICATION.
13. CABINET MOUNTING HARDWARE AND BRACKET MUST BE
APPROVED BY THE ENGINEER.

20-NOV-2013

OCT.
31,
2013

OCT.
31,
2013

OPERATION.
7.

CCTV POLE

4
0"

LOWERING DEVICE CONTROL


CABLE. SEE NOTE 4.

CHAI
RM AN STANDARDS COM M I
TTEE
APPROVED

TOP VIEW

COMMUNICATION

(2) 2 INCH FLEXIBLE


LIQUID TIGHT
STAINLESS STEEL
CONDUIT WITH
COMPRESSION
FITTING

NID MOUNTING DETAIL

MOUNTING BRACKET
SEE STD DWG 11C

MOUNTING BRACKET
SEE STD DWG AT 11C

CABLES

CAMERA LOWERING POLE

M OUNTI
NG DETAI
LS

3/4 INCH STAINLESS STEEL


STRAPS TYP.

3/4 INCH STAINLESS STEEL


STRAPS TYP.

RECOM M ENDED FOR APPROVAL

36x24x22 INCH
NEMA 3S POLE
MOUNTED CABINET
SEE NOTE 3

UTAH DEPARTM ENT OF TRANSPORTATI


ON

36x24x22 INCH
NEMA 3S POLE
MOUNTED CABINET
SEE NOTE 3

45
0"

STATE FURNISHED POLE

STD. DWG. NO.

SUPPLEMENTAL DRAWING

AT 11A

STANDARD DRAW I
NG TI
TLE

45
,60
,OR 80

NID CABLE

APPR.

CAMERA
LOWERING
SYSTEM

ALL OPENINGS

DATE

POLE HAND HOLE


PLUG AND SEAL

NO.

DETECTOR ( IF REQD)

DATE

SIDE MOUNDED
NON INTRUSIVE

SIDE MOUNTED NON-INTRUSIVE


DETECTOR (IF REQD)

DEPUTY DI
RECTOR

CAMERA POLE

REVI
SED NOTES 2,6,AND 8.ADDED NOTES 913.

CCTV
COMPOSITE
CABLE

ON CABLE ROUTI
NG. CHANGED CONDUI
T SI
ZE I
NTO CABI
NET.

ACCESS PANEL

REFLECT DETAI
L C AND STD DW G AT 11C. I
NCREASED DETAI
L

STATE FURNISHED
DOME ASSEMBLY

SALT LAKE CI
TY,UTAH

CAMERA
LOWERING
POLE

CCTV COMPOSITE
CABLE

REVI
SI
ONS

WAVETRONICS
WX-SS-H611
6 AXIS BRACKET
OR EQUIVALENT

DI
RECTI
ON OF TRAVEL

SEE NOTE 2.

STANDARD DRAW I
NGS FOR ROAD AND BRI
DGE CONSTRUCTI
ON

POSITIONER CCTV.

REVI
SED CAM ERA W I
RI
NG DI
AGRAM . REVI
SED NOTE TO

SIDE MOUNTED NID


STATE FURNISHED
CAMERA LOWERING
SYSTEM

M AA

SUPPORT ARM

10/
31/
13

POLETOP JUNCTION
BOX WITH REMOVABLE
TOP CAP

CABLE STRAIN
RELIEF

You might also like