Scribd
Upload
201 views2 pages

Coiltools Dimple Connector Ps

ct tools

Uploaded by

CARLOSELSOARES
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
201 views2 pages

Coiltools Dimple Connector Ps

ct tools

Uploaded by

CARLOSELSOARES
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Dimple Connector

Quickly installs and removes


APPLICATIONS

Standard coiled tubing interventions oil,


gas, and injector wells

Standard HPHT operations

Perforating

Jarring/impact hammers

Milling

ADVANTAGES

Rotational lock holds high amount of torque

Reusable connectors offer multiple use

Allows coiled tubing preparations at base


Sweet and sour services according to
NACE standards
Quick installation and removal

Two O-rings seal on the coil

The dimple connectors are available standard CT sizes of 1 in,


1 in, 2 in, 2 in, and 2 in.

Minimal ID restriction of the CT, allowing


unrestricted flow and the use of wiper
plugs or process balls

Historically, the external set screw, or dimple connector, has been


the preferred style of connector. It is attached to the coiled tubing
end by set screws that engage preformed dimples, which are formed
using a dimpling tool. After the dimpling, the coiled tubing end is
prepared for the O-ring seal by beveling off the end and smoothing
the O-ring seal area. The connector is then slipped up the coiled
tubing; the set screws are torqued in place. Verification of proper
installation is required with a pressure and pull test.

High-strength construction makes


the connector stronger than the coiled
tubing string
Uses 12 knurled grub screws

Dimple connector.

Dimple Connector
Specifications
Part Number OD,
ID,
CT Size
in [mm] in [mm]
100476698

1.69
0.812
1-in CT 1-in AMMT-S
[42.926] [20.625]
PIN

Will Pass
Ball Size,
in [mm]
0.75
[19.05]

100297852

2.13
1.03
112-in CT
[54.102] [26.162]

112-in AMMT-S
PIN

1
[25.4]

6.68
Yes
[169.672]

100297854

2.13
0.812
112-in CT
[54.102] [20.625]

1-in AMMT-S
PIN

0.75
[19.05]

6.68
Yes
[169.672]

100289510

2.875 1.38
134-in CT
[73.025] [35.052]

238-in PAC DSI


PIN

1.25
[31.75]

6.68
Yes
[169.672]

100288814

2.25
1.03
134-in CT
[57.15] [26.162]

112-in AMMT-S
PIN

1
[25.4]

6.68
Yes
[169.672]

100297129

2.56
1.03
2-in CT
[65.024] [26.162]

112-in AMMT-S
PIN

1
[25.4]

6.68
Yes
[169.672]

100297134

2.875 1.38
2-in CT
[73.025] [35.052]

238-in PAC DSI


PIN

1.25
[31.75]

6.68
Yes
[169.672]

100476229

2.875 1.38
238-in CT
[73.025] [35.052]

238-in PAC DSI


PIN

1.25
[31.75]

8.5
[215.9]

Yes

100626341

3.13
1.25
[79.502] [31.75]

238-in CT

238-in API REG


PIN

1.125
[28.575]

8.5
[215.9]

No

100549919

3.13
1.25
[79.502] [31.75]

238-in CT

238-in API REG


PIN

1.125
[28.575]

8.5
[215.9]

Yes

100675642

3.375
[85.725]
3.375
[85.725]

1.75
278-in CT
[44.45]
1.38
278-in CT
[35.052]

238-in API IF
PIN
238-in PAC DSI
PIN

1.625
[41.275]
1.25
[31.75]

8.5
[215.9]
8.5
[215.9]

Yes

100288815

Lower Thread

Make-up Sweet and


length, sour services
in [mm]
6.68
Yes
[169.672]

Yes

Working
Pressure,
psi [kPa]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]
10,000
[68,948]

Tensile
Strength,
lbf [daN]
31,790
[14,141]
63,772
[28,367]
31,790
[14,141]
97,650
[43,437]
57,034
[25,370]
63,772
[28,367]
97,650
[43,437]
74,326
[33,062]
124,992
[55,599]
124,992
[55,599]
84,758
[37,702]
84,758
[37,702]

Torque Capacity,
ft-lbf [daN-m]
374
[51]
1,237
[168]
374
[51]
2,749
[373]
1,237
[168]
1,237
[168]
2,749
[373]
2,749
[373]
4,000
[542]
4,000
[542]
3,778
[512]
3,778
[512]

Values are based on 80-ksi strength steel at 70 degF [21 degC] and a single load case.
At temperatures above 250 degF [121 degC] all ratings for the tool are reduced by 7%, at 350 degF [177 degC] the ratings are reduced by 12%.

All users should determine the actual operating and load parameters for their own application.

slb.com/CoilTOOLS

*Mark of Schlumberger
Copyright 2014 Schlumberger. All rights reserved. 13-CT-0061

You might also like