Class 600 Studding Outlet: Flat Bottom Shell/Head Mount Tangential Mount
Class 600 Studding Outlet: Flat Bottom Shell/Head Mount Tangential Mount
Class 600 Studding Outlet: Flat Bottom Shell/Head Mount Tangential Mount
FLAT BOTTOM
SHELL/HEAD MOUNT
Outside
Dia.
Thick.
RF
O.D.
Stud
Holes
T
1.50
R
1.38
1/2
0
3.75
3/4
4.62
1.75
1.69
4.88
1.75
2.00
1 1/4
5.25
1.75
6.12
2
2 1/2
Size
Hole
Size
TANGENTIAL MOUNT
Hole
Depth
Stud
Circle
Tap
Depth
Stud
Length
27/64
U
0.88
C
2.62
13
V
0.56
1/2
17/32
1.12
3.25
5/8
3.00
11
0.75
3.50
17/32
1.12
3.50
5/8
11
0.75
3.62
2.50
17/32
1.12
3.88
5/8
11
0.75
3.75
1.94
2.88
21/32
1.31
4.50
3/4
10
0.88
4.25
6.50
1.75
3.62
1.12
5.00
5/8
11
0.75
3.88
17/32
21/32
7.50
2.00
4.12
1.31
5.88
3/4
10
0.88
4.50
Tap
Size
T.P.I.
8.25
2.00
5.00
21/32
1.31
6.62
3/4
10
0.88
4.62
3 1/2
9.00
2.12
5.50
49/64
1.44
7.25
7/8
1.00
5.12
10.75
2.12
6.19
49/64
1.44
8.50
7/8
1.00
5.25
13.00
2.25
7.31
7/8
1.56
10.50
1.12
5.88
14.00
2.25
8.50
12
7/8
1.56
11.50
1.12
6.00
16.50
2.50
10.62
12
1.81
13.75
11/8
1.25
6.62
10
20.00
2.75
12.75
16
11/8
2.12
17.00
11/4
1.44
7.38
12
22.00
2.75
15.00
20
11/8
2.12
19.25
11/4
1.44
7.50
14
23.75
2.88
16.25
20
11/4
2.25
20.75
13/8
1.56
8.00
16
27.00
3.00
18.50
20
13/8
2.38
23.75
11/2
1.69
8.62
18
29.25
3.25
21.00
20
11/2
2.56
25.75
15/8
1.88
9.25
20
32.00
3.25
23.00
24
11/2
2.56
28.50
15/8
1.88
9.75
24
37.00
3.75
27.25
24
13/4
3.00
33.00
17/8
2.12
11.12
Material:
Studding Outlets are most commonly provided in SA-105. They can also be made from a full
range of stainless and alloy materials.
Thickness:
The standard thickness shown in charts for all studding outlets is the minimum required per
ASME Section VIII Division I Paragraph UG-43(d) for thread engagement and an ID. mount. It is important to
note that each individual application should be analyzed for proper thickness. See general notes for more details.
Facing:
The studding outlet minimum thickness T includes proper raised face per ANSI B16.5. Outlets
can be supplied with any special facing as needed upon request.
Drilling and Tapping: Studding outlets are furnished to ANSI B16.5 specifications unless otherwise specified.
Thread depth is in accordance with ASME Section VIII Division I Para. UG-43(g) for a design temperature not to
exceed 650F, a base metal stress of 17,500 psi, and a stud stress of 25,000 psi. All other materials exceeding
these stresses should be checked for UG-43 compliance.
Bore:
Bore sizes shown above are standard, other sizes can be furnished upon request.
Curving:
All connections can be furnished contoured to fit any shell, head or cone at an additional cost.