Casting Defect - Fissure Defects

40
Description of defects: Fissure defects
41
Fissure defects
Assistance for decisions P. 139
Sand control P. 179
Fig. 16:
Micrograph of a crack in a grey iron housing caused by the formation of nitrogen molecules.
The dendritic structure of the iron is a characteristic feature. Scale: 10 mm = 16 mm
Characteristic features
Explanations
Mostly narrow crack-like cavities which often run perpendicular

to the casting surface. The interior of the cavity is predominantly
dendritic. The surface of the cracks is not as shiny as that found
with hydrogen pinholes. The defect can be several millimetres
wide.
Where there is an extremely high nitrogen content, the cavities
become round and the surface of the blowhole smooth. There are
no inclusions found in the nitrogen defects.
Molten cast iron containing a high proportion of scrap steel has a

high nitrogen content, which may be in excess of 100 ppm. The
likelihood of ssure defects has grown with the increased use of
scrap steel. The risk of gas defects has also increased through the
use of nitrogen-containing binders (mould and core binders) and
carburizing compounds.
Incidence of the defect

The up to 2 cm deep crack-like cavities, mostly perpendicular
to the surface, frequently have dendritic structures in the surface of the cavity. The defect can occur at mould surfaces and
edges as well as at core surfaces. The ssures arise through the
precipitation of nitrogen during solidication, simultaneous precipitation of hydrogen intensifying the defect even further.
Nitrogen defects can be distributed over a larger area of the
casting than blowholes. A casting with a thicker wall is more likely to show this defect than a casting with a thinner wall.
Possible causes
Metallurgical
Nitrogen content in the melt too high.
Titanium content low relative to comparatively high nitrogen
content.
Carbon equivalent low relative to comparatively high nitrogen content.
Resin-bonded sand
High nitrogen content in the core binder or too much binder
High formation of gas and poor core venting.
Clay-bonded sand
High moisture content in the sand and consequently high
water absorption by the melt.
High nitrogen content in the sand resulting from incoming
core sand or lustrous carbon producer.
42
Fig. 17:
Cracks in a grey iron ring due to formation of nitrogen molecules.

Scale: 10 mm = 4 mm
43
Remedies
Background information
Metallurgical
Reduce proportion of steel in the charge makeup. Reduce
nitrogen content to 100 ppm.
Bind nitrogen content in the melt through the addition of
titanium.
Increase the carbon equivalent.
Fissure defects are principally attributed to the nitrogen content in

the iron melt being too high. Reference works state that the limit
for grey iron and SG cast iron is 100 ppm.1, 2 Below this value,
gas precipitation can be excluded.
A high proportion of scrap steel in the charge make-up will
increase the nitrogen content of the melt. In a test foundry, the
following values were determined 3 in a cupola iron:
Resin-bonded sand
Use binder with lower nitrogen content.
Use binder with slower release of gas; if possible, use
binders with less gas.
Add iron oxides.
Clay-bonded sand
Reduce moisture content through better sand development,
reduced addition of bentonite and smaller amounts of inert
dust.
Reduce nitrogen content in the sand. If necessary, reduce
lustrous carbon carrier content or use low-nitrogen carbon
carrier.
If necessary, reduce nitrogen content in the inowing core
sand.
Gating and pouring practice
Shorten the pouring channels in order to reduce gas pick-up.
Increase pouring temperature and, if necessary, also the
pouring rate.
Proportion of steel [%]
Nitrogen content [ppm]
20
80
100
110
150
170
The solubility of nitrogen in iron can be inuenced by various

alloying elements. Vanadium and chromium increase solubility,
silicon and carbon reduce it.
Nitrogen-containing carburizing compounds can also lead to ssure defects. Reports on such defects have already been presented.4 It is possible to combat these defects by adding titanium
or aluminium to the iron melt. However, the risk of increased
water absorption through the use of these substances should be
considered.
44
45
References
Absorption of nitrogen by the iron melt from the air is unlikely,
due to the high bonding energy of the nitrogen molecule. The
absorption of nitrogen from mould binders is far more signicant. Cold-setting and hot-setting resin binders frequently contain
proportions of urea resin with a high nitrogen content. The Croning technique (shell process) uses hexamethylene tetramine as
the hardener. The isocyanate components of the cold-box hardener also contain nitrogen. The occurrence of defects can be suppressed by the addition of iron oxide.
Nitrogen is readily absorbed from many nitrogen compounds.
In an experiment, increasing quantities of Na3 [Fe(Cn)6] were
added to cast iron with a low carbon equivalent, and the nitrogen
content and formation of defects then determined.3 With a gas
content of 140 ppm, ssure defects arose; with a gas content of
over 300 ppm round gas blowholes formed. Technically, these
high gas contents are meaningless.
In addition to the organic binders, bentonite-bonded sands can
also have an inuence on these defects. The proportion of inowing nitrogen-bearing core sand can have an inuence, as well
as the nitrogen content of the carbon carrier. To avoid defects, it
is recommendable to keep the bentonite and water content as
low as possible.1, 5 There is no standard reference available for
the effectiveness of carbon carriers, but the use of highly active
carbon carriers with a low nitrogen content appears practical
where these defects are experienced.
The addition of barium sulphate, which is recommended in the
literature,5 is also effective. However, problems arise due to the
reduction of the sulphate to sulphide and the subsequent formation of barium hydroxide and hydrogen sulphide, so limiting the
extent to which this technique may be applied
Dawson, J. V.; Kilshaw, J. A.; Morgan, A. D.

Art und Entstehung von Gasblasen in Gueisenteilen
Mod. Cast. 47, 1965, P. 144 160
Greenhill, J. M.; Reynolds, N. M.

Stickstoffeinschlsse in Gueisenteilen
Foundry Trade Journal 151, 1981, P. 111, 113 114,
117 118, 121 122 (English)
Mountford, F. A.
Einu von Stickstoff auf Festigkeit, Dichtigkeit und Gefge
von Gueisen
Brit. Foundrym. 1966, P. 141 151
Davison, M. H.; et al.

Stickstoffporositt in Gueisen mit Lamellengraphit
Trans. Amer. Foundrymen s Soc. 71, 1963, P. 528 543
& 830
van Capelle, G. A. F.
Verhtung bestimmter Oberchenfehler bei Gueisen mit
Lamellengraphit
Foundry Trade 130, 1971, P. 681 684

Casting Defect - Fissure Defects

Uploaded by

Copyright:

Available Formats

Casting Defect - Fissure Defects

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Casting Defect - Fissure Defects

Uploaded by

Copyright:

Available Formats

40

Description of defects: Fissure defects

Description of defects: Fissure defects

Mostly narrow crack-like cavities which often run perpendicular

Molten cast iron containing a high proportion of scrap steel has a

Incidence of the defect

Description of defects: Fissure defects

Cracks in a grey iron ring due to formation of nitrogen molecules.

Description of defects: Fissure defects

Fissure defects are principally attributed to the nitrogen content in

Proportion of steel [%]

Nitrogen content [ppm]

The solubility of nitrogen in iron can be inuenced by various

Description of defects: Fissure defects

Description of defects: Fissure defects

Dawson, J. V.; Kilshaw, J. A.; Morgan, A. D.

Greenhill, J. M.; Reynolds, N. M.

Davison, M. H.; et al.

You might also like