Scribd
Upload
437 views2 pages

SDC 602RF Instruction Manual

Buy the SDC 602RF at JMAC Supply. https://www.jmac.com/Security_Door_Controls_602RF_p/sdc-602rf.htm?=scribd

Uploaded by

JMAC Supply
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
437 views2 pages

SDC 602RF Instruction Manual

Buy the SDC 602RF at JMAC Supply. https://www.jmac.com/Security_Door_Controls_602RF_p/sdc-602rf.htm?=scribd

Uploaded by

JMAC Supply
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SECURITY DOOR CONTROLS

801 Avenida Acaso, Camarillo, Ca. 93012


(805) 494-0622 Fax: (805) 494-8861
www.sdcsecurity.com E-mail: [email protected]

SPECIAL APPLICATIONS POWER SUPPLY


INSTALLATION INSTRUCTIONS
MODEL 602RF

COMPONENT LOCATIONS
MODEL 602RF
CONTROL
MODULE

AC Voltage
Input

POWER
SUPPLY
BOARD

CONTROL
MODULE

BATTERY 1
4ah

BATTERY 2
4ah

STANDARD BOX
AC Voltage
Input
Manuel
Reset

MAIN SYSTEM ON-OFF


OR
FIRE PANEL CONNECTION

System
Status LED

+ _

Yellow = System OK
Red = No AC Input
Green = No DC Output
Battery Input
Terminals

Voltage Output
Terminals

Master ON/OFF
Switch (N/C)

Fire Panel
Contact (N/C)

Min. Switch
OR
Contact Ratings
100mA @ 30vdc

Figure C
Input Voltage: 115/230 VAC @ 60hz
Input Current: 0.8 amps Max.

POWER SUPPLY SPECIFICATIONS


JUMPER SET
FOR 24 VDC

JUMPER SET
FOR 12 VDC

Output Voltage: 12/24VDC (Special Applications)


Burglary Use:
Output Voltage Ranges:
12 V Operation: 9.2 12.0 VDC
24 V Operation: 21.2 24.0 VDC
Output Current: 1.0 amps
Ripple Voltage: 0.05 Volts Max

+
-

+
-

Battery Charger Max Current: 0.25 amps


Maximum recommended battery size: 4ah
(Replace batteries every three years)

12VDC

12VDC
To determine standby battery capacity, refer to
Batter Discharge table (INST-BDT).

12 Volt Mode Battery


Connections

Compatible UL listed Fire Devices:


Smoke detector manufactured by ESL, Model 521B,
521BXT with Model 506 module.

602RF

+- + -

+
Battery

TEST UNIT YEARLY


Rev F

01-12

12VDC

High voltage
Input

Wire Routing

NOT INTENDED TO POWER A LOCAL


BURGLAR ALARM INDICATING DEVICE.

24 Volt Mode Battery


Connections

Suitable Uses:
Electric Lock Power Supply
Access Control Power Supply
Burglar Alarm System Power Supply
Fire Protective Signaling Service

P:\INSTALLATION INST\Power Supplies\INST-602RF.vsd

NOTE:
Power limited cable
must maintain a 1/4
or more spacing from
battery cables or
primary power wires.
Power limited
Class 2 output

SPECIAL APPLICATIONS POWER SUPPLY


INSTALLATION INSTRUCTIONS

801 Avenida Acaso, Camarillo, Ca. 93012


(805) 494-0622 Fax: (805) 494-8861
www.sdcsecurity.com E-mail: [email protected]

MODEL 602RF-CUL

COMPONENT LOCATIONS

MODEL 602RF-CUL

CONTROL
MODULE

POWER
SUPPLY
BOARD

CONTROL
MODULE

AC VOLTAGE
INPUT

BATTERY 1
4ah

BATTERY 1
4ah

STANDARD BOX

BATTERY MONITOR LEDS


GRN = AC
RED = BATTERIES
ORG = NO/LO BATTERY

VOLTAGE SELECT
SWITCHES
MANUAL
RESET

COVER

SYSTEM STATUS
YELLOW SYSTEM OK
RED ON BATTERY PWR
GREEN NO DC OUTPUT

Min. Switch or
Contact Ratings
100mA @ 30VDC

MAIN SYSTEM ON-OFF

BATTERY INPUT
TERMINALS

VOLTAGE OUTPUT
TERMINALS

Master ON/OFF
Switch (N/C)

POWER SUPPLY SPECIFICATIONS


Input Voltage: 115 VAC @ 60hz
Input Current: 0.8 amps Max.
+

Output Voltage: 12/24VDC (Special Applications)


Burglary Use:
Output Voltage Ranges:
12 V Operation: 9.2 12.0 VDC
24 V Operation: 21.2 24.0 VDC
Output Current: 1.0 amps
Ripple Voltage: 0.05 Volts Max.

Monitor Board
_
_
+

12VDC

12VDC

24 Volt Mode Battery


Connections

12 Volt Mode Battery


Connections
HIGH
VOLTAGE
INPUT

To determine standby battery capacity refer to


Battery Discharge Table (INST-BDT).
602RF-CUL

+_ +_

Suitable Uses:
Electric Lock Power Supply
Access Control Power Supply

P:\INSTALLATION INST\Power Supplies\INST-602RF-CUL.vsd

Monitor
_
_ Board
+

12VDC

Battery Charger Max. Current: 0.25 amps


Maximum recommended battery size: 4ah
Recommended Battery: SDC Model RB12V4
(Replace batteries every 3 years)

TEST UNIT ANNUALLY

Battery

Rev B

04-13

Note: Power limited


cable must maintain a
1/4 or more of spacing
from battery cables or
primary power wires.

POWER LIMITED
CLASS 2 OUTPUT

You might also like