Scribd
Upload
262 views3 pages

Gaussian Pulse Propagation

This document describes simulating the broadening of Gaussian pulses transmitted through an optical fiber. It provides the system parameters, including the transmitter pulse width and chirp factor, fiber length and type. It then lists the key pulse and spectral width values to calculate for the transmitted, received and fiber impulse response. The simulation involves generating a Gaussian pulse, transmitting it through the fiber, and measuring the input/output pulse and spectral widths to compare with the calculations.

Uploaded by

fawal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
262 views3 pages

Gaussian Pulse Propagation

This document describes simulating the broadening of Gaussian pulses transmitted through an optical fiber. It provides the system parameters, including the transmitter pulse width and chirp factor, fiber length and type. It then lists the key pulse and spectral width values to calculate for the transmitted, received and fiber impulse response. The simulation involves generating a Gaussian pulse, transmitting it through the fiber, and measuring the input/output pulse and spectral widths to compare with the calculations.

Uploaded by

fawal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Broadening of Gaussian Pulses

Objective:

Compare the results predicted by the linear system model of an optical fiber with the
results of simulation.

Theory:

An optical fiber can be represented approximately by a linear system with an impulse


response h(t) or a transfer function H(jω). If the optical source has a spectral width much
greater than the signal bandwidth (e.g., the source is a directly modulated laser diode) and
the operating wavelength is far from the zero-dispersion wavelength, then H(jω) is
approximately Gaussian, i.e.,

H (ω ) = exp(−TF2ω 2 )

where TF is the RMS width of the impulse response and is given approximately by

TF = LD (λ )Δλ

where L is the fiber length, D(λ) is the fiber dispersion coefficient and Δλ is the RMS
spectral width of the optical source.

A chirped Gaussian pulse can be used to represent the output of a directly modulated
laser diode. A chirped Gaussian pulse is characterized by an RMS pulse width Tin and a
chirp factor C. The RMS pulse width is related to the FWHM pulse width by the
formulas

TFWHM = 1.665Tin

The RMS spectral width of the pulse is obtained from the relationship

λ2 1 + C 2
Δλ =
2πcTin

where λ is the operating wavelength and c is the speed of light.


If a Gaussian pulse is input to a linear system with a Gaussian impulse response, then the
output is also a Gaussian pulse that has an RMS width given by

2
Tout = Tin2 + TF2

where all pulse widths are RMS values.

Calculations:

The system parameters are listed in the following table.

Transmitter – Gaussian Pulse Generator


Operating wavelength 1550 nm
Bit rate 2.5 Gb/s
FWHM pulse width 0.5 Bit period
Chirp factor -6
Fiber
Type Corning SMF-28
Length 50 km

Calculate the following:

Value Symbol
RMS width of transmitted pulse Tin
RMS spectral width of transmitted pulse Δλ
RMS width of fiber impulse response TF
RMS width of pulse at fiber far end Tout

Layout:

Place and connect the following components:

1. User-defined bit sequence generator – set to generate a single pulse of the


specified width
2. Optical Gaussian pulse generator – enter the chirp factor as a negative number
3. Optical fiber – set according to the specifications
4. Optical spectrum analyzers and optical time domain visualizers at input and
output of fiber
Simulation:

Set the parameters and run the simulation and use the visualizer displays to measure the
following:

• FWHM width of input and output pulses


• FWHM width of optical spectra

Analysis:

Compare the simulation results with the calculations and discuss any observed
differences.

You might also like