Esquema

- R1
Router>enable
Router#config terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname R1
R1(config)#interface g0/0
R1(config-if)#ip address 172.16.0.1 255.255.254.0
R1(config-if)#no shut
R1(config)#interface s0/0/0
R1(config-if)#ip address 172.16.6.225 255.255.255.252
R1(config-if)#no shut
R1(config-if)#
R1(config-if)#interface g0/1
R1(config-if)#ip address 172.16.2.1 255.255.254.0
R1(config-if)#no shut
R1>enable
R1#config terminal
R1(config)#router eigrp 1
R1(config-router)#do show ip route connected
C 172.16.0.0/23 is directly connected, GigabitEthernet0/0
C 172.16.2.0/23 is directly connected, GigabitEthernet0/1
C 172.16.6.224/30 is directly connected, Serial0/0/0
R1(config-router)#network 172.16.0.0 0.0.1.255
R1(config-router)#network 172.16.2.0 0.0.1.255
R1(config-router)#network 172.16.6.224 0.0.0.3
R1(config-router)#no auto-summary
R1(config-router)#passive-interface g0/0
R1(config-router)#passive-interface g0/1
R1(config-router)#exit
R1(config)#interface s0/0/0
R1(config-if)#ip hello-interval eigrp 1 12
R1(config-if)#bandwidth 512
R1#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is 172.16.6.226 to network 0.0.0.0

172.16.0.0/16 is variably subnetted, 15 subnets, 7 masks

C

172.16.0.0/23 is directly connected, GigabitEthernet0/0

172.16.0.1/32 is directly connected, GigabitEthernet0/0

172.16.2.0/23 is directly connected, GigabitEthernet0/1

172.16.2.1/32 is directly connected, GigabitEthernet0/1

172.16.4.0/24 [90/6024192] via 172.16.6.226, 00:05:18, Serial0/0/0

172.16.5.0/25 [90/6024192] via 172.16.6.226, 00:05:18, Serial0/0/0

172.16.5.128/25 [90/6024192] via 172.16.6.226, 00:05:08, Serial0/0/0

172.16.6.0/25 [90/6024192] via 172.16.6.226, 00:05:08, Serial0/0/0

172.16.6.128/26 [90/6024192] via 172.16.6.226, 00:04:49, Serial0/0/0

172.16.6.192/27 [90/6024192] via 172.16.6.226, 00:04:49, Serial0/0/0

172.16.6.224/30 is directly connected, Serial0/0/0

172.16.6.225/32 is directly connected, Serial0/0/0

172.16.6.228/30 [90/6023936] via 172.16.6.226, 00:05:26, Serial0/0/0

172.16.6.232/30 [90/6023936] via 172.16.6.226, 00:05:09, Serial0/0/0

172.16.6.236/30 [90/6023936] via 172.16.6.226, 00:04:52, Serial0/0/0

D*EX 0.0.0.0/0 [170/10631936] via 172.16.6.226, 00:07:35, Serial0/0/0

R1#
R1(config)#ip name-server 209.165.200.226
R1(config)#exit
R1#copy running-config tftp
Address or name of remote host []? tftp.practica.com

Destination filename [R1-confg]?

Writing running-config...Translating "tftp.practica.com"...!!

[OK - 955 bytes]

955 bytes copied in 0.012 secs (79000 bytes/sec)

R1#
Captura del server TFTP

R1(config)#line console 0
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#line vty 0 4
R1(config-line)#password cisco
R1(config-line)#login

R1(config-line)#exit
R1(config)#service passwordR1(config)#service password-encryption
R1(config)#banner motd $Advertencia$
R1(config)#

- R2
Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface g0/0
Router(config-if)#ip address 172.16.4.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to

up

Router(config-if)#interface g0/1
Router(config-if)#ip address 172.16.5.1 255.255.255.128
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to

up

Router(config-if)#interface s0/0/0
Router(config-if)#ip address 172.16.6.229 255.255.255.252

Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down

Router(config-if)#exit
Router(config)#Hostname R2
R2>enable
R2#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#router eigrp 1
R2(config-router)#do show ip route connected
C 172.16.4.0/24 is directly connected, GigabitEthernet0/0
C 172.16.5.0/25 is directly connected, GigabitEthernet0/1
C 172.16.6.228/30 is directly connected, Serial0/0/0
R2(config-router)#network 172.16.4.0 0.0.0.255
R2(config-router)#network 172.16.5.0 0.0.0.127
R2(config-router)#network 172.16.6.228 0.0.0.3
R2(config-router)#no auto-summary
R2(config-router)#passive-interface g0/0
R2(config-router)#passive-interface g0/1
R2(config-router)#exit
R2(config)#interface s0/0/0
R2(config-if)#ip hello-interval eigrp 1 12
R2(config-if)#bandwidth 512
R2>show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is 172.16.6.230 to network 0.0.0.0

172.16.0.0/16 is variably subnetted, 15 subnets, 7 masks

D

172.16.0.0/23 [90/6024192] via 172.16.6.230, 00:06:12, Serial0/0/0

172.16.2.0/23 [90/6024192] via 172.16.6.230, 00:06:12, Serial0/0/0

172.16.4.0/24 is directly connected, GigabitEthernet0/0

172.16.4.1/32 is directly connected, GigabitEthernet0/0

172.16.5.0/25 is directly connected, GigabitEthernet0/1

172.16.5.1/32 is directly connected, GigabitEthernet0/1

172.16.5.128/25 [90/6024192] via 172.16.6.230, 00:05:33, Serial0/0/0

172.16.6.0/25 [90/6024192] via 172.16.6.230, 00:05:33, Serial0/0/0

172.16.6.128/26 [90/6024192] via 172.16.6.230, 00:05:14, Serial0/0/0

172.16.6.192/27 [90/6024192] via 172.16.6.230, 00:05:14, Serial0/0/0

172.16.6.224/30 [90/6023936] via 172.16.6.230, 00:06:17, Serial0/0/0

172.16.6.228/30 is directly connected, Serial0/0/0

172.16.6.229/32 is directly connected, Serial0/0/0

172.16.6.232/30 [90/6023936] via 172.16.6.230, 00:05:33, Serial0/0/0

172.16.6.236/30 [90/6023936] via 172.16.6.230, 00:05:17, Serial0/0/0

D*EX 0.0.0.0/0 [170/10631936] via 172.16.6.230, 00:08:00, Serial0/0/0

R2>
R2>enable
R2#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#ip name-server 209.165.200.226
R2(config)#exit
R2#
%SYS-5-CONFIG_I: Configured from console by console

R2#copy run tftp

Address or name of remote host []? tftp.practica.com

Destination filename [R2-confg]?

Writing running-config...Translating "tftp.practica.com"...!!

[OK - 957 bytes]

957 bytes copied in 0.011 secs (87000 bytes/sec)

R2#

- R3
Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R3
R3(config)#interface g0/0
R3(config-if)#ip address 172.16.5.129 255.255.255.128
R3(config-if)#no shut

R3(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to

up

R3(config-if)#interface g0/1
R3(config-if)#ip address 172.16.6.1 255.255.255.128
R3(config-if)#no shut

R3(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to

up

R3(config-if)#interface s0/0/0
R3(config-if)#ip address 172.16.6.233 255.255.255.252
R3(config-if)#no shut

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down

R3(config-if)#
R3(config-if)#exit
R3(config)#
R3>enable
R3#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
R3(config)#router eigrp 1
R3(config-router)#do show ip route connected
C 172.16.5.128/25 is directly connected, GigabitEthernet0/0
C 172.16.6.0/25 is directly connected, GigabitEthernet0/1
C 172.16.6.232/30 is directly connected, Serial0/0/0
R3(config-router)#network 172.16.5.128 0.0.0.127
R3(config-router)#network 172.16.6.0 0.0.0.127
R3(config-router)#network 172.16.6.232 0.0.0.3
R3(config-router)#no auto-summary
R3(config-router)#passive-interface g0/0
R3(config-router)#passive-interface g0/1
R3(config-router)#exit
R3(config)#interface s0/0/0
R3(config-if)#ip hello-interval eigrp 1 12
R3(config-if)#bandwidth 512
R3#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is 172.16.6.234 to network 0.0.0.0

172.16.0.0/16 is variably subnetted, 15 subnets, 7 masks

D

172.16.0.0/23 [90/6024192] via 172.16.6.234, 00:06:40, Serial0/0/0

172.16.2.0/23 [90/6024192] via 172.16.6.234, 00:06:40, Serial0/0/0

172.16.4.0/24 [90/6024192] via 172.16.6.234, 00:06:11, Serial0/0/0

172.16.5.0/25 [90/6024192] via 172.16.6.234, 00:06:11, Serial0/0/0

172.16.5.128/25 is directly connected, GigabitEthernet0/0

172.16.5.129/32 is directly connected, GigabitEthernet0/0

172.16.6.0/25 is directly connected, GigabitEthernet0/1

172.16.6.1/32 is directly connected, GigabitEthernet0/1

172.16.6.128/26 [90/6024192] via 172.16.6.234, 00:05:42, Serial0/0/0

172.16.6.192/27 [90/6024192] via 172.16.6.234, 00:05:42, Serial0/0/0

172.16.6.224/30 [90/6023936] via 172.16.6.234, 00:06:45, Serial0/0/0

172.16.6.228/30 [90/6023936] via 172.16.6.234, 00:06:19, Serial0/0/0

172.16.6.232/30 is directly connected, Serial0/0/0

172.16.6.233/32 is directly connected, Serial0/0/0

172.16.6.236/30 [90/6023936] via 172.16.6.234, 00:05:45, Serial0/0/0

D*EX 0.0.0.0/0 [170/10631936] via 172.16.6.234, 00:08:28, Serial0/0/0

R3#
R3>enable
R3#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
R3(config)#ip name-server 209.165.200.226
R3(config)#exit
R3#
%SYS-5-CONFIG_I: Configured from console by console

R3#copy run tftp

Address or name of remote host []? tftp.practica.com
Destination filename [R3-confg]?

Writing running-config...Translating "tftp.practica.com"...!!

[OK - 963 bytes]

963 bytes copied in 0.002 secs (481000 bytes/sec)

R3#

- R4
Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R4
R4(config)#interface g0/0
R4(config-if)#ip address 172.16.6.129 255.255.255.192
R4(config-if)#no shut

R4(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to

up

R4(config-if)#interface g0/1
R4(config-if)#ip address 172.16.6.193 255.255.255.224
R4(config-if)#no shut

R4(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to

up

R4(config-if)#interface s0/0/0
R4(config-if)#ip address 172.16.6.237 255.255.255.252
R4(config-if)#no shut

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down

R4(config-if)#
R4>enable
R4#config ter
Enter configuration commands, one per line. End with CNTL/Z.
R4(config)#router eigrp 1
R4(config-router)#do show ip route connected
C 172.16.6.128/26 is directly connected, GigabitEthernet0/0
C 172.16.6.192/27 is directly connected, GigabitEthernet0/1
C 172.16.6.236/30 is directly connected, Serial0/0/0
R4(config-router)#network 172.16.6.128 0.0.0.63
R4(config-router)#network 172.16.6.192 0.0.0.31
R4(config-router)#network 172.16.6.236 0.0.0.3
R4(config-router)#no auto-summary
R4(config-router)#passive-interface g0/0
R4(config-router)#passive-interface g0/1
R4(config-router)#exit
R4(config)#interface s0/0/0
R4(config-if)#ip hello-interval eigrp 1 12
R4(config-if)#bandwidth 512
R4#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is 172.16.6.238 to network 0.0.0.0

172.16.0.0/16 is variably subnetted, 15 subnets, 7 masks

D

172.16.0.0/23 [90/6024192] via 172.16.6.238, 00:05:10, Serial0/0/0

172.16.2.0/23 [90/6024192] via 172.16.6.238, 00:05:10, Serial0/0/0

172.16.4.0/24 [90/6024192] via 172.16.6.238, 00:04:41, Serial0/0/0

172.16.5.0/25 [90/6024192] via 172.16.6.238, 00:04:41, Serial0/0/0

172.16.5.128/25 [90/6024192] via 172.16.6.238, 00:04:31, Serial0/0/0

172.16.6.0/25 [90/6024192] via 172.16.6.238, 00:04:31, Serial0/0/0

172.16.6.128/26 is directly connected, GigabitEthernet0/0

172.16.6.129/32 is directly connected, GigabitEthernet0/0

172.16.6.192/27 is directly connected, GigabitEthernet0/1

172.16.6.193/32 is directly connected, GigabitEthernet0/1

172.16.6.224/30 [90/6023936] via 172.16.6.238, 00:05:15, Serial0/0/0

172.16.6.228/30 [90/6023936] via 172.16.6.238, 00:04:49, Serial0/0/0

172.16.6.232/30 [90/6023936] via 172.16.6.238, 00:04:31, Serial0/0/0

172.16.6.236/30 is directly connected, Serial0/0/0

172.16.6.237/32 is directly connected, Serial0/0/0

D*EX 0.0.0.0/0 [170/10631936] via 172.16.6.238, 00:06:58, Serial0/0/0

R4#
R4>enable
R4#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
R4(config)#ip name-server 209.165.200.226
R4(config)#exit

R4#
%SYS-5-CONFIG_I: Configured from console by console

R4#copy run tftp

Address or name of remote host []? tftp.practica.com
Destination filename [R4-confg]?

Writing running-config...Translating "tftp.practica.com"...!!

[OK - 965 bytes]

965 bytes copied in 0.012 secs (80000 bytes/sec)

R4#

- HQ
Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname HQ
HQ(config)#interface s0/0/1
HQ(config-if)#ip address 172.16.6.226 255.255.255.252
HQ(config-if)#clock rate 128000
HQ(config-if)#no shut
HQ(config-if)#interface s0/1/0
HQ(config-if)#ip address 172.16.6.230 255.255.255.252
HQ(config-if)#clock rate 128000
HQ(config-if)#no shut
HQ(config-if)#interface s0/1/1
HQ(config-if)#ip address 172.16.6.234 255.255.255.252
HQ(config-if)#clock rate 128000
HQ(config-if)#no shut

HQ(config-if)#interface s0/1/0
HQ(config-if)#clock rate 128000
HQ(config-if)#interface s0/2/0
HQ(config-if)#ip address 172.16.6.238 255.255.255.252
HQ(config-if)#clock rate 128000
HQ(config-if)#no shut
HQ(config-if)#interface s0/0/0
HQ(config-if)#ip address 209.165.200.234 255.255.255.252
HQ(config-if)#no shut
HQ>enable
HQ#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
HQ(config)#ip route 0.0.0.0 0.0.0.0 s0/0/0
HQ(config)#router eigrp 1
HQ(config-router)#do show ip route connected
C 172.16.6.224/30 is directly connected, Serial0/0/1
C 172.16.6.228/30 is directly connected, Serial0/1/0
C 172.16.6.232/30 is directly connected, Serial0/1/1
C 172.16.6.236/30 is directly connected, Serial0/2/0
C 209.165.200.232/30 is directly connected, Serial0/0/0
HQ(config-router)#network 172.16.6.224 0.0.0.3
HQ(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.225 (Serial0/0/1) is up: new
adjacency

HQ(config-router)#network 172.16.6.228 0.0.0.3

HQ(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.229 (Serial0/1/0) is up: new
adjacency

HQ(config-router)#network 172.16.6.232 0.0.0.3

HQ(config-router)#

%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.233 (Serial0/1/1) is up: new

adjacency

HQ(config-router)#network 172.16.6.236 0.0.0.3

HQ(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.237 (Serial0/2/0) is up: new
adjacency

HQ(config-router)#no auto-summary
HQ(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.229 (Serial0/1/0) is up: new
adjacency

%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.237 (Serial0/2/0) is up: new

adjacency

%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.233 (Serial0/1/1) is up: new

adjacency

%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.225 (Serial0/0/1) is up: new

adjacency

HQ(config-router)#passive-interface s0/0/0
HQ(config-router)#redistribute static
HQ(config-router)#exit
HQ(config)#interface s0/0/1
HQ(config-if)#ip hello-interval eigrp 1 12
HQ(config-if)#bandwidth 512
HQ(config-if)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.225 (Serial0/0/1) is down:
interface down

HQ(config-if)#

%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.225 (Serial0/0/1) is up: new

adjacency

HQ(config-if)#interface s0/1/0
HQ(config-if)#ip hello-interval eigrp 1 12
HQ(config-if)#bandwidth 512
HQ(config-if)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.229 (Serial0/1/0) is down:
interface down

HQ(config-if)#interface s0/1/1
HQ(config-if)#ip hello-interval eigrp 1 12
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.229 (Serial0/1/0) is up: new
adjacency

HQ(config-if)#bandwidth 512
HQ(config-if)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.233 (Serial0/1/1) is down:
interface down

%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.233 (Serial0/1/1) is up: new

adjacency

HQ(config-if)#interface s0/2/0
HQ(config-if)#ip hello-interval eigrp 1 12
HQ(config-if)#bandwidth 512
HQ(config-if)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.237 (Serial0/2/0) is down:
interface down

HQ(config-if)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 172.16.6.237 (Serial0/2/0) is up: new
adjacency
HQ#show ip route

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

172.16.0.0/16 is variably subnetted, 16 subnets, 7 masks

D

172.16.0.0/23 [90/5512192] via 172.16.6.225, 00:04:07, Serial0/0/1

172.16.2.0/23 [90/5512192] via 172.16.6.225, 00:04:07, Serial0/0/1

172.16.4.0/24 [90/5512192] via 172.16.6.229, 00:03:37, Serial0/1/0

172.16.5.0/25 [90/5512192] via 172.16.6.229, 00:03:37, Serial0/1/0

172.16.5.128/25 [90/5512192] via 172.16.6.233, 00:03:28, Serial0/1/1

172.16.6.0/25 [90/5512192] via 172.16.6.233, 00:03:28, Serial0/1/1

172.16.6.128/26 [90/5512192] via 172.16.6.237, 00:03:09, Serial0/2/0

172.16.6.192/27 [90/5512192] via 172.16.6.237, 00:03:09, Serial0/2/0

172.16.6.224/30 is directly connected, Serial0/0/1

172.16.6.226/32 is directly connected, Serial0/0/1

172.16.6.228/30 is directly connected, Serial0/1/0

172.16.6.230/32 is directly connected, Serial0/1/0

172.16.6.232/30 is directly connected, Serial0/1/1

172.16.6.234/32 is directly connected, Serial0/1/1

172.16.6.236/30 is directly connected, Serial0/2/0

172.16.6.238/32 is directly connected, Serial0/2/0

209.165.200.0/24 is variably subnetted, 2 subnets, 2 masks

209.165.200.232/30 is directly connected, Serial0/0/0

209.165.200.234/32 is directly connected, Serial0/0/0

S* 0.0.0.0/0 is directly connected, Serial0/0/0

HQ#
HQ>enable
HQ#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
HQ(config)#line console 0
HQ(config-line)#password cisco
HQ(config-line)#login
HQ(config-line)#line vty 0 15
HQ(config-line)#password cisco
HQ(config-line)#login
HQ(config-line)#exit
HQ(config)#service passwo
HQ(config)#service password-encryption
HQ(config)#banner motd $Advertencia$
HQ(config)#
HQ(config)#ip access-list extended HQACL
HQ(config-ext-nacl)#permit tcp any any
HQ(config-ext-nacl)#interface s0/2/0
HQ(config-if)#ip access-group HQACL in
HQ(config-if)#

- ISP
Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname ISP
ISP(config)#interface s0/0/0
ISP(config-if)#ip address 209.165.200.233 255.255.255.252
ISP(config-if)#clock rate 128000
ISP(config-if)#no shut
ISP(config-if)#interface g0/0
ISP(config-if)#ip address 209.165.200.225 255.255.255.248

ISP(config-if)#no shut
ISP>enable
ISP#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
ISP(config)#ip route 172.16.0.0 255.255.0.0 s0/0/0
ISP(config)#
ISP(config)#^Z
ISP#
%SYS-5-CONFIG_I: Configured from console by console

ISP#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is not set

172.16.0.0/16 is directly connected, Serial0/0/0

209.165.200.0/24 is variably subnetted, 4 subnets, 3 masks

209.165.200.224/29 is directly connected, GigabitEthernet0/0

209.165.200.225/32 is directly connected, GigabitEthernet0/0

209.165.200.232/30 is directly connected, Serial0/0/0

209.165.200.233/32 is directly connected, Serial0/0/0

- Resultados

Capturas de la pc de la primera LAN del R1