HT27C512

CMOS 64K8-Bit OTP EPROM

Features
Operating voltage: +5.0V

64K8-bit organization

Programming voltage
- VPP=12.2V0.2V

Fast read access time: 70ns

Fast programming algorithm

- VCC=5.8V0.2V

Programming time 75ms typ.

High-reliability CMOS technology

Two line control (OE & CE)

Latch-up immunity to 100mA from -1.0V to

Standard product identification code

VCC+1.0V

Commercial temperature range (0C to +70C)

CMOS and TTL compatible I/O

28-pin DIP/SOP, 32-pin PLCC package

Low power consumption

- Active: 30mA max.
- Standby: 1mA typ.

General Description
e l i m i n a t e s t h e n e e d f o r W A I T st a t e s i n
high-performance microprocessor systems. The
HT27C512 has separate Output Enable (OE) and Chip
Enable (CE) controls which eliminate bus contention issues.

The HT27C512 chip family is a low-power, 512K bit, +5V

electrically one-time programmable (OTP) read-only
memories (EPROM). Organized into 64K words with 8
bits per word, it features a fast single address location
programming, typically at 75ms per byte. Any byte can
be accessed in less than 70ns with respect to Spec. This

Block Diagram

R o w
A d d re s s
C o lu m n
A d d re s s
C E
O E /V P P

Rev. 1.30

X -D e c o d e r

C e ll A r r a y
V C C

Y -D e c o d e r

Y - G a tin g

C E & O E &
P G M & T E S T
C o n tr o l L o g ic

S A C K T
&
O u tp u t B u ffe r

V S S

D Q 0 ~ D Q 7

September 12, 2002

HT27C512
Pin Assignment

V S S

1 4

1 5

D Q 3

2 3

1 2

2 2

1 3

2 1

2 7

A 4

A 3

A 1 3
A 8
A 9
A 1 1

A 2

1 0

A 1

1 1

2 3

A 0
D Q 0

1 2

2 2

1 3

2 1

D Q 5
D Q 4
D Q 3

N C
V S S
D Q 2
D Q 1

H T 2 7 C 5 1 2
2 8 D IP -A /S O P -A

2 6

H T 2 7 C 5 1 2
3 2 P L C C -B

2 5
2 4

D Q 6

D Q 4

1 1

A 5

D Q 5

1 6

A 0
N C
D Q 0

2 4

A 1 1
N C
O E /V P P
A 1 0
C E
D Q 7
D Q 6

2 0

1 3

1 0

2 5

A 1 4

2 8

1 9

D Q 2

A 1

2 6

H T 2 7 C 5 1 2
3 2 P L C C -A

2 9
6

1 8

D Q 5

3 0
3 1

1 7

A 2

A 6

1 7

1 2

3 2

D Q 1

N C
N C
V C C

D Q 6

A 3

A 7

1 6

1 8

2 7

1 1

D Q 0

A 4

A 8
A 9

D Q 4
D Q 3
V S S
D Q 2
D Q 1

D Q 7

2 8

1 5

1 0

1 9

1 4

A 0

C E

A 1 0

2 0

N C
N C
A 1 5

2 1
9

A 1 2

A 1

2 9
5

A 5

2 0

A 2

A 6

1 9

O E /V P P

1 8

2 2

3 0
3 1

A 1 1

A 3

1 7

2 3

3 2

A 1 3
A 1 4
V C C

A 9

A 4

1 6

2 4

A 8

A 5

A 1 3

2 5

2 6
4

1 5

A 6

1 4

A 7

A 1 4

V C C

2 7

2 8
2

N
A 1
A 1
A

A 1 5
A 1 2

O E /V P P
A 1 0
C E
D Q 7

Pin Description
Pin Name
A0~A15
DQ0~DQ7
CE

I/O/P
I
I/O
I

Description
Address inputs
Data inputs/outputs
Chip enable

OE/VPP

I/P

Output enable/program voltage supply

NC

No connection

VCC

Positive power supply

VSS

Negative power supply, ground

Absolute Maximum Ratings

Operation Temperature Commercial ..........................................................................................................0C to +70C
Storage Temperature.............................................................................................................................-65C to 125 C
Applied VCC Voltage with Respect to VSS ................................................................................................-0.6V to 7.0V
Applied Voltage on Input Pin with Respect to VSS .....................................................................................-0.6V to 7.0V
Applied Voltage on Output Pin with Respect to VSS ......................................................................... -0.6V to VCC+0.5V
Applied Voltage on A9 Pin with Respect to VSS ...................................................................................... -0.6V to 13.5V
Applied VPP Voltage with Respect to VSS...............................................................................................-0.6V to 13.5V
Applied READ Voltage (Functionality is guaranteed between these limits) ..............................................+4.5V to +5.5V
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.

Rev. 1.30

September 12, 2002

HT27C512
D.C. Characteristics
Symbol

Parameter

Test Conditions
Conditions

VCC

Min.

Typ.

Max.

Unit

Read operation
VOH

Output High Level

5V

IOH=-0.4mA

2.4

VOL

Output Low Level

5V

IOL=2.1mA

0.45

VIH

Input High Level

5V

2.0

VCC+0.5

VIL

Input Low Level

5V

-0.3

0.8

ILI

Input Leakage Current

5V

VIN=0 to 5.5V

-5

mA

ILO

Output Leakage Current

5V

VOUT=0 to 5.5V

-10

10

mA

ICC

VCC Active Current

5V

CE=VIL, f=5MHz, IOUT=0mA

30

mA

ISB1

Standby Current (CMOS)

5V

CE=VCC0.3V

1.0

10

mA

ISB2

Standby Current (TTL)

5V

CE=VIH

1.0

mA

IPP

VPP Read/Standby Current

5V

CE=OE=VIL, VPP=VCC

100

mA

Programming operation
VOH

Output High Level

5.8V IOH=-0.4mA

2.4

VOL

Output Low Level

5.8V IOL=2.1mA

0.45

VIH

Input High Level

5.8V

0.7VCC

VCC+0.5

VIL

Input Low Level

5.8V

-0.5

0.8

ILI

Input Load Current

5.8V VIN=VIL, VIH

5.0

mA

VH

A9 Product ID Voltage

5.8V

11.5

12.5

ICC

VCC Supply Current

5.8V

40

mA

IPP

VPP Supply Current

5.8V CE=VIL

10

mA

Capacitance
CIN

Input Capacitance

5V

VIN=0V

12

pF

COUT

Output Capacitance

5V

VOUT=0V

12

pF

CVPP

VPP Capacitance

5V

VPP=0V

18

25

pF

Rev. 1.30

September 12, 2002

HT27C512
A.C. Characteristics
Symbol

Ta=25C5C
Parameter

Test Conditions
VCC

Conditions

Min.

Typ.

Max.

Unit

Read operation
tACC

Address to Output Delay

5V

CE=OE=VIL

70

ns

tCE

Chip Enable to Output Delay

5V

OE=VIL

70

ns

tOE

Output Enable to Output Delay

5V

CE=VIL

30

ns

tDF

CE or OE High to Output Float, Whichever

Occurred First

5V

25

ns

tOH

Output Hold from Address, CE or OE,

Whichever Occurred First

5V

ns

Programming operation
tAS

Address Setup Time

5.8V

ms

tOES

CE/VPP Setup Time

5.8V

ms

tOEH

OE/VPP Hold Time

5.8V

ms

tDS

Data Setup Time

5.8V

ms

tAH

Address Hold Time

5.8V

ms

tDH

Data Hold Time

5.8V

ms

tDFP

Output Enable to Output Float Delay

5.8V

130

ns

tPW

PGM Program Pulse Width

5.8V

30

75

105

ms

tVCS

VCC Setup Time

5.8V

ms

tDV

Data Valid From CE

5.8V

150

ns

tVR

OE/VPP Recovery Time

5.8V

ms

Test waveforms and measurements

2 .4 V
A C

D r iv in g
L e v e ls
0 .4 5 V

2 .0 V
0 .8 V

Output test load

1 .3 V

A C

M e a s u re m e n t
L e v e l

(1 N 9 1 4 )
3 .3 k 9

tR, tF< 20ns (10% to 90%)

O u tp u t P in
C
L

Note: CL=100pF including jig capacitance.

Rev. 1.30

September 12, 2002

HT27C512
Functional Description
To activate this mode, the programming equipment
must force 12.00.5V on the address line A9 of the
HT27C512. Two identifier bytes may then be sequenced from the device outputs by toggling address
line A0 from VIL to VIH, when A1=VIH. All other address
lines must be held at VIH during Auto Product Identification mode.

Programming of the HT27C512

When the HT27C512 is delivered, the chip has all 512K
bits in the ONE or HIGH state. ZEROs are loaded
into the HT27C512 through the procedure of programming.
The programming mode is entered when 12.20.2V is
applied to the OE/VPP pin and CE is at VIL. For programming, the data to be programmed is applied with 8
bits in parallel to the data pins.

Byte 0 (A0=VIL) represents the manufacturer code, and

byte 1 (A0=VIH), the device code. For HT27C512, these
two identifier bytes are shown in the Operation mode
truth table. All identifiers for the manufacturer and device codes will possess odd parity, with the MSB (DQ7)
defined as the parity bit. When A1=VIL, the HT27C512
will read out the binary code of 7F, continuation code, to
signify the unavailability of manufacturer ID codes.

The programming flowchart in Figure 3. shows the fast

interactive programming algorithm. The interactive algorithm reduces programming time by using 30ms to
105ms programming pulses and giving each address
only as many pulses as is necessary in order to reliably
program the data. After each pulse is applied to a given
address, the data in that address is verified. If the data is
not verified, additional pulses are given until it is verified
or until the maximum number of pulses is reached. This
process is repeated while sequencing through each address of the HT27C512. This part of the programming
algorithm is carried at VCC=5.8V to assure that each
EPROM bit is programmed to a sufficiently high threshold voltage. This ensures that all bits have sufficient
margin. After the final address is completed, the entire
EPROM memory is read at VCC=VPP=5.250.25V to verify
the entire memory.

Read mode
The HT27C512 has two control functions, both of which
must be logically satisfied in order to obtain data at outputs. Chip Enable (CE) is the power control and should
be used for device selection. Output Enable (OE) is the
output control and should be used to gate data to the
output pins, independent of device selection. Assuming
that addresses are stable, address access time () is
equal to the delay from CE to output (tCE). Data is available at the outputs (tOE) after the falling edge of OE, assuming the CE has been LOW and addresses have
been stable for at least tACC-tOE.

Program inhibit mode

Standby mode

Programming of multiple HT27C512 in parallel with different data is also easily accomplished by using the Program Inhibit Mode. Except for CE, all like inputs of the
parallel HT27C512 may be common. A TTL low-level
program pulse applied to an HT27C512 CE input with
OE/VPP=12.20.2V will program that HT27C512. A
high-level CE input inhibits the other HT27C512 from
being programmed.

The HT27C512 has CMOS standby mode which reduces the maximum VCC current to 10mA. It is placed in
CMOS standby when CE is at V C C 0.3V. The
HT27C512 also has a TTL-standby mode which reduces the maximum VCC current to 1.0mA. It is placed
in TTL-standby when CE is at VIH. When in standby
mode, the outputs are in a high-impedance state, independent of the OE input.

Program verify mode

Two-line output control function

Verification should be performed on the programmed

bits to determine whether they were correctly programmed. The verification should be performed with
OE/VPP and CE at VIL. Data should be verified at tDV after the falling edge of CE.

To accommodate multiple memory connections, a

two-line control function is provided to allow for:
Low memory power consumption
Assurance that output bus contention will not occur.

It is recommended that CE be decoded and used as the

primary device-selection function, while OE be made a
common connection to all devices in the array and connected to the READ line from the system control bus.
This assures that all deselected memory devices are in
their low-power standby mode and that the output pins
are only active when data is desired from a particular
memory device.

Auto product identification

The Auto Product Identification mode allows the reading
out of a binary code from an EPROM that will identify its
manufacturer and type. This mode is intended for use by
the programming equipment for the purpose of automatically matching the device to be programmed with its
corresponding programming algorithm. This mode is
functional in the 25C5C ambient temperature range
that is required when programming the HT27C512.

Rev. 1.30

September 12, 2002

HT27C512
System considerations

VCC and VPP to minimize transient effects. In addition,

to overcome the voltage drop caused by the inductive
effects of the printed circuit board traces on EPROM arrays, a 4.7mF bulk electrolytic capacitor should be used
between VCC and VPP for each eight devices. The location of the capacitor should be close to where the
power supply is connected to the array.

During the switch between active and standby conditions, transient current peaks are produced on the rising
and falling edges of Chip Enable. The magnitude of
these transient current peaks is dependent on the output capacitance loading of the device. At a minimum, a
0.1mF ceramic capacitor (high frequency, low inherent
inductance) should be used on each device between
Operation mode truth table
All the operation modes are shown in the table following.
CE

OE/VPP

A0

A9

Output

VIL

VIL

X (2)

Dout

Output Disable

VIL

VIH

High Z

Standby (TTL)

VIH

High Z

VCC 0.3V

High Z

Program

VIL

VPP

DIN

Program Verify

VIL

VIL

DOUT

Product Inhibit

VIH

VPP

High Z

Manufacturer Code (3)

VIL

VIL

VIL

VH (1)

1C

Device Type Code (3)

VIL

VIL

VIH

VH (1)

83

Mode
Read

Standby (CMOS)

Notes: (1) VH=12.0V 0.5V

(2) X=Either VIH or VIL
(3) For Manufacturer Code and Device Code, A1=VIH, When A1=VIL, both codes will read 7F

Product Identification Code

Pins
A0

A1

DQ7

DQ6

DQ5

DQ4

DQ3

DQ2

DQ1

DQ0

Hex
Data

Manufacturer

1C

Device Type

83

7F

7F

Code

Continuation

A d d re s s

A d d r e s s V a lid
tC

C E

tD
tO

O E
tA
O u tp u t

H IG H

tO

C C

O u tp u t V a lid
Z

Figure 1. A.C. waveforms for read operation

Rev. 1.30

September 12, 2002

HT27C512
R e a d
( V e r ify )

P ro g ra m
A d d re s s

IH

O E /V P P

C E

tA

IH

D a ta

V C C

A d d r e s s S ta b le

IL

tD
S

tA
V

D a ta In

IL

tD

tD
S

5 .8 V

tD

5 .0 V
1 2 .2 V
V

C S
E S

IL

tO
tP

tV
tO

F P

E H

tV

R T

IH

D a ta O u t
V a lid

IL

tP
W

Figure 2. Programming waveforms

S T A R T

A d d r e s s = F ir s t L o c a tio n

V
V

C C
P P

= 5 .8 V
= 1 2 .2 V

X = 0

O n e 7 5 m s P u ls e

P ro g ra m

In te r a c tiv e
S e c tio n

In c re m e n t X

X = 2 5 ?

Y e s

N o
F a il

V e r ify
B y te ?
P a s s

In c re m e n t A d d re s s

L a s t
A d d re s s

N o

F a il

Y e s
V
V e r ify
S e c tio n

C C

= 5 .2 5 V

V e r ify a ll
B y te s ?

F a il

D e v ic e F a ile d

P a s s
D e v ic e P a s s e d
N o te : E ith e r 1 0 5 m s o r 3 0 m s p u ls e .

Figure 3. Fast programming flowchart

Rev. 1.30

September 12, 2002

HT27C512
Package Information
28-pin DIP (600mil) outline dimensions
A
1 5

2 8
B
1

1 4

H
C
D
E

Symbol

Rev. 1.30

=
G

Dimensions in mil
Min.

Nom.

Max.

1445

1465

535

555

145

155

125

145

16

20

50

70

100

595

615

635

670

15

September 12, 2002

HT27C512
28-pin SOP (300mil) outline dimensions

2 8

1 5

A
B
1

1 4

C
C '
G
H
D
E

Symbol

Rev. 1.30

=
F

Dimensions in mil
Min.

Nom.

Max.

394

419

290

300

14

20

697

713

92

104

50

32

38

12

10

September 12, 2002

HT27C512
32-pin PLCC outline dimensions

A
1
4

3 2

2 9

2 8

1 2

2 1
1 3

2 0
K

E
J
H

Symbol

Rev. 1.30

Dimensions in mil
Min.

Nom.

Max.

485

495

445

455

585

595

545

555

105

115

140

15

50

16

22

24

32

12

10

10

September 12, 2002

HT27C512
Product Tape and Reel Specifications
Reel dimensions
D

T 2

C
B

T 1

SOP 28W (300mil)

Symbol

Description

Dimensions in mm

Reel Outer Diameter

3301.0

Reel Inner Diameter

621.5

Spindle Hole Diameter

Key Slit Width

2.0+0.6

T1

Space Between Flange

24.40.2

T2

Reel Thickness

28.4+0.4

Rev. 1.30

12.75+0.15

11

September 12, 2002

HT27C512
Carrier tape dimensions

P 0
D

P 1
t

E
F
W
C

D 1

B 0

K 0
A 0

SOP 28W (300mil)

Symbol

Description

Dimensions in mm

Carrier Tape Width

24.00.3

Cavity Pitch

12.00.1

Perforation Position

1.750.1

Cavity to Perforation (Width Direction)

11.50.1

Perforation Diameter

1.5+0.1

D1

Cavity Hole Diameter

1.5+0.25

P0

Perforation Pitch

4.00.1

P1

Cavity to Perforation (Length Direction)

2.00.1

A0

Cavity Length

10.850.1

B0

Cavity Width

18.340.1

K0

Cavity Depth

2.970.1

Carrier Tape Thickness

0.350.01

Cover Tape Width

Rev. 1.30

21.3

12

September 12, 2002

HT27C512

Holtek Semiconductor Inc. (Headquarters)

No.3, Creation Rd. II, Science-based Industrial Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Sales Office)
11F, No.576, Sec.7 Chung Hsiao E. Rd., Taipei, Taiwan
Tel: 886-2-2782-9635
Fax: 886-2-2782-9636
Fax: 886-2-2782-7128 (International sales hotline)
Holtek Semiconductor (Shanghai) Inc.
7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China
Tel: 021-6485-5560
Fax: 021-6485-0313
http://www.holtek.com.cn
Holtek Semiconductor (Hong Kong) Ltd.
RM.711, Tower 2, Cheung Sha Wan Plaza, 833 Cheung Sha Wan Rd., Kowloon, Hong Kong
Tel: 852-2-745-8288
Fax: 852-2-742-8657
Holmate Semiconductor, Inc.
48531 Warm Springs Boulevard, Suite 413, Fremont, CA 94539
Tel: 510-252-9880
Fax: 510-252-9885
http://www.holmate.com
Copyright 2002 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek reserves the right to alter its products without prior notification. For the most
up-to-date information, please visit our web site at http://www.holtek.com.tw.

Rev. 1.30

13

September 12, 2002