FIGURE 7.
56
Finger Guide.
FIGURE 7.57
Rod Support.
FIGURE 7.58
Tool Holder.
FIGURE 7.59
Tailstock Clamp.
FIGURE 7.60
Index Feed.
FIGURE 7.61
Bearing.
FIGURE 7.62
Holder Clip.
FIGURE 7.63
Cam.
FIGURE 7.64
Index Arm.
FIGURE 7.65
Roller Lever.
FIGURE 7.66
Support.
FIGURE 7.67
Locating Finger.
FIGURE 7.68
Toggle Lever.
FIGURE 7.69
Cut-off Holder.
FIGURE 7.70
Index Slide.
FIGURE 7.71
Frame Guide.
FIGURE 7.72
Chuck Jaw.
FIGURE 7.73
Hinge Bracket.
FIGURE 7.74
Tool Holder.
FIGURE 7.75
Shifter Block.
FIGURE 7.76
Cross-feed Stop.
FIGURE 7.77
Cross Cam.
FIGURE 7.78
Roller Stud.
FIGURE 7.79
Hinge Block.
FIGURE 7.80
Feed Rod Bearing.
FIGURE 7.81
Lever Hub.
FIGURE 7.82
Vibrator Arm.
FIGURE 7.83
Clutch Lever.
FIGURE 7.84
Counter Bearing Bracket.
FIGURE 7.85
Tool Holder.
FIGURE 7.86
Control Block.
FIGURE 7.87
Socket Bearing.
FIGURE 7.88
Tool Holder.
FIGURE 7.89
Locating V-Block.
FIGURE 7.90
Anchor Bracket.
FIGURE 7.91
Door Bearing.
FIGURE 7.92
Vise Base.
FIGURE 7.93
Dust Cap.
FIGURE 7.94
Chuck Jaw.
FIGURE 7.95
Holder.
FIGURE 7.96
Centering Wedge.
FIGURE 7.97
Motor Switch Lever. Draw or sketch necessary views.
FIGURE 7.98
Socket Form RollerLH. Draw or sketch necessary views.
FIGURE 7.99
Stop Base. Draw or sketch necessary views.
FIGURE 7.100
Hinge Base. Draw or sketch necessary views.
FIGURE 7.101
Automatic Stop Base. Draw or sketch necessary views.
FIGURE 7.102
Lead Screw Bracket. Draw or sketch necessary views.
FIGURE 7.103
Lever Bracket. Draw or sketch necessary views.
FIGURE 7.104
Gripper Rode Center. Draw or sketch necessary views.
FIGURE 7.105
Bearing Bracket. Draw or sketch necessary views.
FIGURE 7.106
Link Arm Connector. Draw or sketch necessary views.
FIGURE 7.107
Mounting Bracket. Draw or sketch necessary views.
FIGURE 7.108
LH Shifter Fork. Draw or sketch necessary views.
FIGURE 7.109
Gear Shift Bracket. Draw or sketch necessary views.
FIGURE 7.110
Fixture Base.
FIGURE 7.111
Ejector Base.
FIGURE 7.112
Tension Bracket.
FIGURE 7.113
Offset Bearing.
FIGURE 7.114
Feed Guide.
FIGURE 7.115
Feed Shaft Bracket. Given: Front and top views. Required: Front, top, and right-side views, half size.
FIGURE 7.116
Trip Lever. Given: Front, top, and partial side views. Required: Front, bottom, and left-side views, drawn completely.
FIGURE 7.117
Knurl Bracket Bearing. Given: Front and left-side views. Required: Take front as top view on new drawing, and add front and right-side views.
FIGURE 7.118
Horizontal Bracket for Broaching Machine. Given: Front and top views. Required: Take top as front view in new drawing; then add top and left-side views.
FIGURE 7.119
Boom Swing Bearing for a Power Crane. Given: Front and bottom views. Required: Front, top, and left-side views.
FIGURE 7.120
Sliding Nut for Mortiser. Given: Top and right-side views. Required: Front, top, and left-side views, full size.
FIGURE 7.121
Power Feed Bracket for Universal Grinder. Given: Front and right-side views. Required: Front, top, and left-side views, full size.
CHAPTER 7 - CAD AT WORK
Multiview Projection from a 3D Model. (A)
CHAPTER 7 - CAD AT WORK
Multiview Projection from a 3D Model. (B)
CHAPTER 7 - CAD AT WORK
Multiview Projection from a 3D Model. (C)
