Brush Bond

Brushbond*
Acrylic polymer modified protective and

decorative coating for concrete and masonry
Uses
Properties
To protect atmospherically exposed reinforced concrete

structures from attack by acid gases, chloride ions, oxygen
and water. The product is also suitable to protect other
cementitious substrates and masonry for new and existing
structures. Typical applications include :
n Re-facing and reprofiling concrete & masonry surfaces
Pot life
Colours
Application temp
Toxicity
:
:
Properties (cured)
Tensile strength
(ASTM C307)
Flexural strength
Bond strength
Chloride ion resistance
1 month (% Cl detected)
6 months (% Cl detected)
Moisture vapour
Permeability flux
(g/m2/day)
Carbonation resistance
depth of penetration (mm)
n Flexible coating to bridge shrinkage cracks

n Waterproof coating for water tanks and reservoirs
n Robust coating which can withstand pedestrian traffic
Advantages
n Excellent barrier to carbon dioxide, chloride ions and water

n Allows water vapour to escape from the structure
n Water proof - suitable for water retaining structures
n High resistance to the effects of long-term weathering,
durable in all climatic conditions including UV attack
n Minimum surface preparation needed and low labour costs
n Non toxic - ideal for potable water tanks
1 hour @ 20oC
20 mins @ 35oC
grey and white,
special colours on request
not less than 5oC
to BS6920 section 4.2.8
immersion test - negligible
effect on potable water.
Brushbond
slurry coat*
:
:
:
:
3.75 N/mm2
11 N/mm2
3.5 N/mm2
coated
0.0004
0.0004
2.0 N/mm2
4 N/mm2
0.5 N/mm2
uncoated
0.0063
0.0344
204
844
n Flexible, with thermal expansion similar to concrete

n Covers honeycombed and pitted poured concrete
effectively
n Good abrasion resistance
Specification
Standards compliance
Acrylic polymer modified protective/decorative coating
Tested to :
BS6920 (section 4.2.8 immersion test)

ASTM C307
Description
Brushbond comprises a two component acrylic polymer

modified cementitious coating supplied in ready to mix kits.
Brushbond can be simply applied by stiff brush, roller, spray
or trowel to obtain the desired texture.
Design criteria
Brushbond
* A 1:3 sand/cement slurry coat adjusted with water for same

workability as mixed Brushbond for brush application
The coating should be applied in two coats to achieve a total

dry film thickness of not less than 2mm. Areas subjected to
light foot traffic should receive minimum 2mm thickness and
an additional 2mm coating should be applied to areas of
moderate to heavy pedestrian conditions. To achieve the
correct protective properties, Brushbond must be applied on
to the substrate at the coverage rates recommended.
The protective coating shall comprise specially selected

cements, graded hardwearing aggregates and additives
supplied in powder form together with a liquid component of
blended acrylic co-polymers and wetting agents. The total
dry film thickness of the coating shall be not less than 2 mm
and shall be capable of providing resistance to wear and
weather and good chemical resistance to mild inorganic acid
solution, diesel oil, gasoline, chlorides, de-icing salts, effluents
and organic solvents. It shall exhibit positive water pressure
resistance up to 7 metre head, dependent on coating thickness.
Instructions for use
Preparation
All surfaces should be dry and free from contamination such
as oil, grease, loose particles, decayed matter, laitance, and all
traces of mould release oils and curing compounds. This is
best achieved by lightly grit-blasting the surface.
Where moss, algae or similar growths have occurred,
treatment with a proprietary biocide should be carried out
after the grit-blasting process.
Spalled and deeply disintegrated concrete should be removed
to sound concrete and repaired with a Fosroc repair system.
For further advice, consult the local Fosroc office.
It is essential that all surfaces to be treated be pre-soaked with
clean water prior to application of Brushbond.
It is recommended that for general resurfacing each coat should

be 1mm thick. Areas subjected to light foot traffic should
receive at least 2mm thickness of Brushbond and an additional
2mm should be applied if conditions are moderate to heavy
pedestrian traffic.
If in doubt about the condition of the substrate, the local Fosroc
office should be consulted.
Cleaning
Brushbond should be removed from tools and equipment with
clean water immediately after use. Hardened material can be
removed mechanically.
Limitations
Where subsequent coatings or paints are required, trials

should be conducted to ensure compatibility. For further
advice, consult the local Fosroc office.
Brushbond should not be applied if the temperature of the

substrate is below 5C.
Brushbond should not be applied where there is a

likelihood of exposure to frost within 48 hours of the
application.
Brushbond should not be applied in windy conditions

where early-age dust adhesion may occur, or where rain is
likely within 2 hours at 20C or 20 hours at 5C (up to
80% RH).
Mixing
Brushbond liquid should be poured from the plastic container
into the metal drum provided. For brush application
consistency mix with a slow speed drill (500 r.p.m.) fitted with
a Fosroc Mixing Paddle (MR3).
The powder component should be added gradually to the liquid
to avoid lump formation and mixed for 2 to 4 minutes.
Brushbond should be immediately used after mixing. Do not
mix more material than can be used within the pot life. Keep
mixing Brushbond during the application.
Application
Technical support
Application of Brushbond on hot substrates (i.e. over 40 C

surface temperature) will need the prior application of a primer
coat. Mix Brushbond and water in slurry like consistency and
apply Brushbond over the primer whilst it is still wet.
o
For best results, surfaces should be damp. In order to obtain

the protective properties of Brushbond, it is important that
the correct rates of application are observed.
Fosroc offers a comprehensive technical support service to

specifiers, end users and contractors. It is also able to offer
on-site technical assistance, an AutoCAD facility and
dedicated specification assistance in locations all over the
world.
Use a short stiff brush (preferably 120 - 200mm width) and

apply in one or two coats as required.
Spray applications should use the correct mixing ratio to obtain
satisfactory consistency. In hot climatic conditions, it is likely
that spray application will be the best for exterior decorative
finishes. Nozzle size should be 3-4mm and pressure of 6-8
bars should be used.
Brushbond - Page 2 of 4
Estimating
Precautions
Supply
Industrial kit
Powder
Liquid
Health and safety

:
:
:
27 kg pack consisting of:

20 kg bag
7 kg pail
Theoretical 14.2 m/ 1mm

thickness - Coverage
figures given are theoretical,
due to wastage factors and
the variety and nature of
possible substrates,
practical coverage figures
will be reduced.
Coverage
Brushbond
Brushbond contains cement powders which, when mixed or

become damp, release alkalis which can be harmful to the
skin. During use, avoid inhalation of dust and contact with
skin and eyes. Wear suitable protective clothing, gloves, eye
protection and respiratory protective equipment. The use of
barrier creams provide additional skin protection. In case of
contact with skin, rinse with plenty of clean water, then cleanse
with soap and water. In case of contact with eyes, rinse
immediately with plenty of clean water and seek medical
advice. If swallowed, seek medical attention immediately do not induce vomiting.
Fire
Storage
Brushbond components are non-flammable.
Shelf life
For further information, refer to the product Material Safety

Data Sheet.
Combined products have a shelf life of 6 months if kept in a

dry store in the original, unopened packs.
Storage conditions
Store in cool, dry conditions, away from sources of heat and
naked flames, in the original, unopened packs. If stored at
high temperatures and/or high humidity conditions the shelf
life will be reduced. Brushbond liquid component should be
protected from frost.
Brushbond - Page 3 of 4
Additional Information
Fosroc manufactures a wide range of complementary

products which include :
n waterproofing membranes & waterstops
n joint sealants & filler boards
n cementitious & epoxy grouts
n specialised flooring materials
Fosroc additionally offers a comprehensive package of
products specifically designed for the repair and refurbishment
of damaged concrete. Fosrocs Systematic Approach to
concrete repair features the following :
n hand-placed repair mortars
n spray grade repair mortars
n fluid micro-concretes
n chemically resistant epoxy mortars
n anti-carbonation/anti-chloride protective coatings
n chemical and abrasion resistant coatings
For further information on any of the above, please consult
your local Fosroc office - as below.
* Denotes the trademark of Fosroc International Limited
REGIONAL SALES OFFICES IN :
Al Gurg Fosroc LLC

P. O. Box 657
Dubai
United Arab Emirates
TEL : (04) 285 8606
FAX : (04) 285 9649
See separate data sheet
DUBAI
ABU DHABI
BAHRAIN
KUWAIT
OMAN
QATAR
Al Gurg Fosroc
Al Gurg Fosroc
YBA Kanoo
Boodai
GETCO
Tadmur
TEL : 285 8787
TEL : 673 1779
TEL : 738200
TEL : 481 7618
TEL : 771 5080
TEL : 441 3628
FAX : 285 2023
FAX : 673 1449
FAX : 732828
FAX : 483 2124
FAX : 771 7554
FAX : 444 0812
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of sale, copies of which
may be obtained on request. Whilst Fosroc endeavours to ensure that the technical information on this data sheet is correct at the time of printing, it is the
customers responsibility to satisfy himself, by checking with the company that this information is still current at the time of use, that the product is suitable for
the intended application, and that the actual conditions of use are in accordance with those recommended. Because Fosroc has no control over the conditions of
use of its products, all recommendations or suggestions regarding the use of these products are made without guarantee.
www.fosrocgulf.com
UAE/0325/00/A

Brush Bond

Uploaded by

Copyright:

Available Formats

Brush Bond

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Brush Bond

Uploaded by

Copyright:

Available Formats

Brushbond*

Acrylic polymer modified protective and

To protect atmospherically exposed reinforced concrete

n Flexible coating to bridge shrinkage cracks

n Excellent barrier to carbon dioxide, chloride ions and water

n Flexible, with thermal expansion similar to concrete

Acrylic polymer modified protective/decorative coating

BS6920 (section 4.2.8 immersion test)

Brushbond comprises a two component acrylic polymer

* A 1:3 sand/cement slurry coat adjusted with water for same

The coating should be applied in two coats to achieve a total

The protective coating shall comprise specially selected

Instructions for use

It is recommended that for general resurfacing each coat should

Where subsequent coatings or paints are required, trials

Brushbond should not be applied if the temperature of the

Brushbond should not be applied where there is a

Brushbond should not be applied in windy conditions

Application of Brushbond on hot substrates (i.e. over 40 C

For best results, surfaces should be damp. In order to obtain

Fosroc offers a comprehensive technical support service to

Use a short stiff brush (preferably 120 - 200mm width) and

Health and safety

27 kg pack consisting of:

Theoretical 14.2 m/ 1mm

Brushbond contains cement powders which, when mixed or

Brushbond components are non-flammable.

For further information, refer to the product Material Safety

Combined products have a shelf life of 6 months if kept in a

Fosroc manufactures a wide range of complementary

* Denotes the trademark of Fosroc International Limited

REGIONAL SALES OFFICES IN :

Al Gurg Fosroc LLC

See separate data sheet

TEL : 285 8787

TEL : 673 1779

TEL : 481 7618

TEL : 771 5080

TEL : 441 3628

FAX : 285 2023

FAX : 673 1449

FAX : 483 2124

FAX : 771 7554

FAX : 444 0812

You might also like