Tamrock Cha - 560

CHA 560
Technical Specification
04360-1
2004-06-01
CHA 560
TAMROCK
APPLICATION
PowerTrak CHA 560 is a hydraulic top hammer
crawler drill designed for 5189 mm (2"3")
diameter blast holes in construction projects using
R32 and T38 (11/4" and 1") extension drill steels.
PowerTrak CHA 560 is a robust drill in construction
and therefore very well suited for work in demanding
terrain. It is equipped with HL510 hydraulic rock drill,
chain feed, telescopic boom and powerpack, all
mounted on an oscillating FL6 type undercarriage.
The crosswise mounted powerpack - engine, air
compressor and hydraulic pumps - is mounted at the
rear of the rig to balance the weight of the boom,
feed and rock drill. This keeps the body of the drill
short and guarantees good stability. Fitted with
powerful tramming motors the gradeability of the unit
is excellent.
PowerTrak CHA 560 is powered by Caterpillar

3056E diesel engine, which fulfills TIER II & STAGE
II emission requirements, and features lower fuel
consumption and longer service life than
conventional diesel engines. The drill is fitted with a
complete safety and monitoring system for easy
operation and fast maintenance.
All drilling and boom controls are based on proven
hydraulic components. This straightforward design
ensures reliable operation, easy trouble shooting and
simple service and maintenance procedures. The
optional feed-percussion follow-up in control system
ensures maximum penetration rates and rock tool
service life in all rock conditions. The cooling system
on CHA 560 is designed for wide temperature range,
from the extreme cold in the North to the heat of
deserts.
1/3
CHA 560
04360-1
2004-06-01
DRILLING COVERAGE
1m
1m
DIMENSIONS
7700
1200
CHA 560
TAMROCK
2580
2650
Boom extension
9200
2/3
CHA 560
04360-1
2004-06-01
STANDARD COMPONENTS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Rock drill
Chain feed
Rod rack
Telescopic boom
Undercarriage
Powerpack
Hydraulic system
Control system
Dust collection
system
Pressure gauge
set
Reversing alarm
Suction head
Working lights
Manuals
TRANSPORT DIMENSIONS
HL510
CF145 H12
For 7 rods
ZB 700 H
FL 6, oscillating
Diesel engine, hydraulic
pumps and flushing air
compressor
Open center
TDCD, direct hydraulic
DC600H, hydraulic
For accumulators
PE100S, moveable
5 pcs
For operating, maintenance
and spare parts
2 sets of books
2 sets of CD-roms
(Toolman)
Weight (without options)

Width
Height
Total length
12 000 kg
2 500 mm
2 650 mm
9 200 mm
CHOICE OF DRILL STEELS

Drill rod
type
Drill steel
diameter
Recommended
hole diameter
Extension
rods
32 mm (R32)
1"
5164 mm
22
MF-rods
32 mm (R32)
1"
51 - 64 mm
2"2"
Extension
rods
38 mm (T38)
1
6489 mm
23
MF-rods
38 mm (T38)
1"
6489 mm
2" - 3"
Extension
rods
45 mm
1 "
76 - 89 mm
3" - 3 "
MF-rods
45 mm
1 "
76 - 89 mm
3" - 3 "
CHA560 can drill single pass 4148 mm diameter

holes using R32 extension or MF-rods
SELECTION OF OPTIONS
1.
17.
2.
Hose reel (only for 12' rods)

Rod handler RH714
3.
Movable control panel
4.
Mechanical angle indicator MEC Angie
5.
Spirit level angle indicator
6.
Electric fuel filling pump
7.
Hydraulic winch (7 tons)
8.
Control system with feed/ percussion follow-up
9.
Guides for track chains
10.
Three- bar grouser plates *)
11.
Flushing control automatics
12.
Primary separator PE50
13.
Shut-down of suction for water holes
14.
Water injection system with tank
15.
Water injection system without tank
16.
Hydraulic rear jack HM75
18.
Fuel powered coolant heater for engine and

hydraulic oil
Towing hook
19.
Feed/rod handler wear part kit for other steels
20.
Sanrock Mini H hydraulic bit grinder
21.
22.
Biograderable hydraulic oil, Shell Naturelle

HFE46
Additional set of manuals
23.
First service kit for 600 engine hours
24.
Special tools for HL510, field kit

ID 880 817 19
Special tools for HL 510, complete
ID 152 257 68
Antifreeze for air lines
25.
26.
*) Replaces standard component
www.tamrock.com
SANDVIK TAMROCK reserves the right to change this specification without further notice
SANDVIK TAMROCK OY, P.O.Box 100, FIN-33311 Tampere, FINLAND

Tel.int. +358 205 44 121, Telefax int. +358 205 44 120
3/3

Tamrock Cha - 560

Uploaded by

Copyright:

Available Formats

Tamrock Cha - 560

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tamrock Cha - 560

Uploaded by

Copyright:

Available Formats

CHA 560

PowerTrak CHA 560 is powered by Caterpillar

Weight (without options)

CHOICE OF DRILL STEELS

CHA560 can drill single pass 4148 mm diameter

Hose reel (only for 12' rods)

Movable control panel

Mechanical angle indicator MEC Angie

Spirit level angle indicator

Electric fuel filling pump

Hydraulic winch (7 tons)

Control system with feed/ percussion follow-up

Guides for track chains

Three- bar grouser plates *)

Flushing control automatics

Primary separator PE50

Shut-down of suction for water holes

Water injection system with tank

Water injection system without tank

Hydraulic rear jack HM75

Fuel powered coolant heater for engine and

Feed/rod handler wear part kit for other steels

Sanrock Mini H hydraulic bit grinder

Biograderable hydraulic oil, Shell Naturelle

First service kit for 600 engine hours

Special tools for HL510, field kit

*) Replaces standard component

SANDVIK TAMROCK OY, P.O.Box 100, FIN-33311 Tampere, FINLAND

You might also like