Personal Protective Equipment

For
General Industry

Consultation Education & Training (CET) Division

Michigan Occupational Safety & Health Administration
Michigan Department of Licensing and Regulatory Affairs
www.michigan.gov/miosha
(517) 322-1809
SP #16 (Revised 10/10)

Table of Contents
TOPIC

PAGE NUMBER

Safety Related Personal Protective Equipment for General Industry

Introduction

.....................................................................................................

Requirements for PPE A Check List..................................................................

Hazard Assessment and Equipment Selection (3308)..........................................
Training Employees in the Proper Use of PPE (3309...........................................
Sharing PPE (3313)...............................................................................................
Eye and Face Protection........................................................................................
Head Protection (3370).........................................................................................
Foot and Leg Protection (3383)..........................................................................
Hand and Arm Protection (3392)........................................................................
Safety Belts, Harnesses, Lifelines, and Lanyards (3390)...................................
Personal Protective Equipment (PPE) Appendices:
A-1.
A-2.
B-1.
B-2.
B-3.
B-4.
C.
D.
E.
F.

PPE Hazard Assessment Certification....................................................

Types of PPE Chart.................................................................................
PPE Hazard Assessment Form................................................................
PPE Hazard Assessment Certification Form...........................................
PPE Worksheet........................................................................................
PPE Sample Walk Through Survey and Certification Form...................
PPE Training Certificate.........................................................................
Sample Personal Protective Equipment Test..........................................
PPE Training and Fit-Test Form.............................................................
PPE Policy..............................................................................................

Safety-Related Personal Protective Equipment

General Industry
Introduction
Hazards exist in every workplace in many different forms: sharp edges, falling
objects, flying sparks, chemicals, noise and a myriad of other potentially
dangerous situations.
Controlling a hazard at its source is the best way to protect employees. When
engineering, work practice and administrative controls cant protect employees,
employers must provide personal protective equipment (PPE) to their employees
and ensure its use. PPE is equipment worn to minimize exposure to a variety of
hazards.
This guide will help both employers and employees do the following:

Understand the types of PPE.

Know the basics of conducting a hazard assessment of the workplace.
Select appropriate PPE for a variety of circumstances.
Understand what kind of training is needed in the proper use and care of
PPE.

The information in this guide is general in nature and does not address all
workplace hazards or PPE requirements. The information, methods and
procedures are based on the MIOSHA requirements for PPE as set forth in Part
33. Personal Protective Equipment and Part 380. Noise Exposure.

The Requirements for PPE A Checklist

To ensure the greatest possible protection for employees in the workplace, the
cooperative efforts of both employers and employees will help in establishing and
maintaining a safe and healthy work environment.
In general, employers are responsible for:
___
___
___
___
___
___

Performing a hazard assessment of the workplace to identify and control

hazards.
Certifying, in writing, completion of a hazard assessment.
Identifying and providing appropriate PPE for employees.
Training and retraining employees in the use and care of the PPE.
Maintaining PPE, including replacing worn or damaged PPE.
Periodically reviewing, updating and evaluating the effectiveness of the
PPE program.

In general, employees should:

___
___
___
___

Properly wear PPE,

Attend training sessions on PPE,
Care for, clean and maintain PPE, and
Inform a supervisor of the need to repair or replace PPE.

Hazard Assessment And Equipment Selection (3308)

1. Conduct a workplace survey. Conduct a walk-through survey to identify
sources of hazards to feet, head, eyes and face of workers. Reassess
whenever a new hazard is introduced into the workplace.
Care should be taken to recognize the possibility of multiple and
simultaneous exposure to a variety of hazards. Adequate protection against
the highest level of each of the hazards should be provided.
Sources
During the walk-through survey, observe:
a.

b.
c.
d.
e.
f.
g.
h.
i.
j.

Sources of impact/motion; i.e., machinery or processes where any

movement of tools, machine elements or particles could exist or
movement of personnel that could result in collision with
stationary objects;
Sources of high temperatures that could result in burns, eye injury
or ignition of protective equipment, etc.;
Types of chemical exposures;
Sources of hazardous atmospheres;
Sources of hazardous radiation, i.e., welding, brazing, cutting,
furnaces, heat treating, high intensity lights, etc.;
Sources of falling objects or potential for dropping objects;
Sources of sharp objects which might pierce the feet or cut hands;
Sources of rolling or pinching objects which could crush the feet;
Layout of the workplace and location of co-workers; and
Any electrical hazards.

2.

Organize and analyze data. When the walk-through is complete, the

employer should organize and analyze the data so that it may be efficiently
used in determining the proper types of PPE required at the worksite. The
employer should become aware of the different types of PPE available and
the levels of protection offered.

3.

Select Personal Protective Equipment. Select PPE which ensures a level

of protection greater than the minimum required to protect employees
from the hazards. PPE that fits well and is comfortable to wear will
encourage employee use.

4.

Fit the device. If PPE does not fit properly, it can make the difference
between being safely covered or dangerously exposed. It may not provide
the level of protection desired and may discourage employee use.

5.

Reassess hazards. When new equipment and/or processes introduce

hazards that might require revised PPE strategies.

Training Employees In The Proper Use Of PPE (3309)

Employers are required to train each employee who must use PPE. Employees
must be trained to know at least the following:

When PPE is necessary;

What PPE is necessary;
How to properly put on, take off, adjust and wear the PPE;
The limitations of the PPE;
Proper care, maintenance, useful life and disposal of PPE;
Additional requirements when sharing PPE.

Employers should make sure that each employee demonstrates an understanding

of the PPE training as well as the ability to properly wear and use PPE before
they are allowed to perform work requiring the use of PPE. If an employer
believes that a previously trained employee is not demonstrating the proper
understanding and skill level in the use of PPE, that employee should receive
retraining. Other situations that require additional or retraining of employees
include changes in the workplace or in the type of required PPE that make prior
training obsolete.
The employer must document the training of each employee required to wear or
use PPE by preparing a certification containing the name of each employee
trained, the date of training and a clear identification of the subject of the
certification.
Note: See Appendix B1-B4 for sample assessment forms
See Appendix A for sample certification letter

Sharing PPE (3313)

An employer may choose to provide one pair of protective eyewear for each
position rather than individual eyewear for each employee. If this is done, the
employer must make sure that employees disinfect shared protective eyewear
after each use. Protective eyewear with corrective lenses may only be used by the
employee for whom the corrective prescription was issued and may not be shared.

Eye And Face Protection (3312)

Employees can be exposed to a large number of hazards that pose danger to their
eyes and face. MIOSHA required employers to ensure that employees have
appropriate eye or face protection if they are exposed to front and/or side impact
hazards from:

Flying objects and particles;

Molten metal;
Liquid chemicals;
Acids or caustic liquids;
Chemical gases or vapors;
Potentially infected material;
Glare;
Injurious radiation;
Electrical flash.

Selection
Selecting the most suitable eye and face protection for employees should take
into consideration the following elements:

Ability to protect against specific workplace hazards;

Should fit properly and be reasonably comfortable to wear;
Should provide unrestricted vision and movement;
Should be durable and cleanable;
Should allow unrestricted functioning of any other required PPE.

The eye and face protection selected for employee use must clearly identify
the manufacturer. Any new eye and face protective devices must comply with
ANSI Z87.1-1989 or be at least as effective as this standard requires.
Welding Operations (3312(8))
The intense light associated with welding operations can cause serious and
sometimes permanent eye damage if operators do not wear proper eye
protection. The intensity of light or radiant energy produced by welding,
cutting or brazing operations varies according to a number of factors including
the task producing the light, the electrode size and arc current. Table 2 in
Part 33. Personal Protective Equipment shows the minimum protective shades
for a variety of welding, cutting and brazing operations in general industry.

Lenses (3353)
Lenses intended for use in eye protectors are of 4 basic types.

Clear lenses which are impact-resisting and provide protection against

flying objects. The use of tinted lenses for cosmetic purposes is not
acceptable. Clear lenses must transmit not less than 89% of visible
radiation. To wear a tinted lens that transmits less than 89%, a medical
statement should be provided.

Absorptive lenses of shades 1.7 through 3.0 which are impact-resisting

and provide protection against flying objects and glare or which are
impact-resisting and provide protection against flying objects, and
narrowband spectral transmittance of injurious radiation. Shaded lenses
greater than 3.0 should be worn when employees are exposed to injurious
radiation as defined in the employers hazard assessment and Table 2 of
Part 33. Personal Protective Equipment.

Protective-corrective lenses which are impact-resisting and either clear

or absorptive, as specified for persons requiring visual correction.

Filter lenses that are impact resisting and provide protection against flying
objects and narrow-band spectral transmittance of injurious radiation.

Note: See Appendix C for PPE Training Certification

Note: See Appendix D for Sample Test used to demonstrate understanding

Head Protection (3370)

A head injury can impair an employee for life or can be fatal. Protecting
employees from potential head injuries by wearing a safety helmet or hardhat is
one of the easiest ways to protect an employees head from injury.
Employers must ensure that their employees wear head protection if they are
exposed to any of the following:

Falling or flying objects;

Other harmful contacts or exposures;
Risk of injury from electrical shock;
Chemicals;
Temperature extremes;
Hair entanglement.

Types of Hard Hats:

Class A hard hats provide impact and penetration resistance along with
limited voltage protection (up to 2,200 volts).
Class B hard hats provide the highest level of protection against electrical
hazards, with high-voltage shock and burn protection (up to 20,000 volts).
They also provide protection from impact and penetration hazards by
flying/falling objects.
Class D protective hats provide limited voltage protection (fire fighters
service helmets with full brim.)

In Michigan a Class C helmet or any metallic head device shall not be

furnished by an employer or used by an employee for head protection, except
where chemicals would deteriorate other types of protective or safety hats or
caps.
Hair Enclosures (3378)
Where there is a danger of hair entanglement in moving machinery or
equipment, or where there is exposure to means of ignition, a hat, cap or net
shall be used. Hair enclosures shall be reasonably comfortable, completely
enclose all loose hair, and be adjustable to accommodate all head sizes.
Materials shall be fast dyed and non-irritating to the skin.

Cleaning and Inspection of Head Protection

Inspect daily shell, suspension headgear, accessories for holes, cracks,
tears, anything that compromises the protective value of the hat
Consult manufacturer for proper cleaning procedures
Store away from direct sunlight
Never drill holes, paint, or apply labels, may reduce integrity of
protection.
Remove and replace if visible perforations, cracking or deformity of brim
or shell. Loss of surface gloss, chalking or flaking.
Remove if it sustains an impact, even if damage is not noticeable.

Foot and Leg Protection (3383)

Employees who face possible foot or leg injuries from falling or rolling
objects or from crushing or penetrating materials should wear protective
footwear. Also, employees whose work involves exposure to hot substances,
corrosive, or poisonous materials must have protective gear to cover exposed
body parts, including legs and feet. If an employees feet may be exposed to
electrical hazards, non-conductive footwear should be worn. On the other
hand, workplace exposure to static electricity may necessitate the use of
conductive footwear.
Examples of situations in which an employee should wear foot and/or leg
protection include:

When heavy objects such as barrels or tools might roll onto or fall on the
employees feet;
Working with sharp objects such as nails or spikes that could pierce the
soles or uppers of ordinary shoes;
Exposure to molten metal that might splash on feet or legs (see Parts 42Forging, 44-Foundries, and 45-Die Casting for specific requirements);
Working on or around hot, wet or slippery surfaces; and
Working when electrical hazards are present.

Foot and leg protection choices include the following:

Safety shoes have impact-resistant toes and heat-resistant soles that
protect the feet against hot work surfaces common in roofing, paving and
hot metal industries. The metal insoles of some safety shoes protect
against puncture sounds. Safety shoes may also be designed to be
electrically conductive to prevent buildup of static electricity or non
conductive to protect workers from workplace electrical hazards.
Leggings protect the lower legs and feet from heat hazards such as molten
metal or welding sparks.
Metatarsal guards protect the instep from impact and compression.
Toe guards fit over the toes of regular shoes to protect the toes from
impact and compression hazards.

Hand And Arm Protection (3392)

Where potential injury to hands and arms cannot be eliminated through
engineering and work practice controls, employers must ensure that employees
wear appropriate protection. Potential hazards include:

Skin absorption of harmful substances (look for skin warning on MSDS);

Chemical or thermal burns;
Electrical dangers; and
Bruises, abrasions, cuts, punctures.

Types of Protective Gloves

There are many types of gloves available today to protect against a wide variety
of hazards. Following are examples of some factors that may influence the
selection of protective gloves for a workplace:

Types of chemicals handled;

Nature of contact (total immersion, splash, etc.);
Duration of contact;
Area requiring protection (hand only, forearm, arm);
Grip requirements (dry, wet, oily);
Thermal protection;
Size and comfort;
Abrasion/resistance requirements.

Gloves made from a wide variety of materials are designed for many types of
workplace hazards. In general, gloves fall into four groups:

Gloves made of leather, canvas, or metal mesh;

Fabric and coated fabric gloves;
Chemical--and liquid--resistant gloves;
Insulating rubber gloves (see 3385).

Care of Protective Gloves

Inspect before each use (tears, punctures, anything making gloves
ineffective, discoloration, stiffness);
Discard if protective ability is impaired.

Safety Belts, Harnesses, Lifelines, And Lanyards (3390)

Unless protected by a perimeter guardrail or working on a portable ladder, the employee
must be safe guarded by a safety harness secured to a lifeline or structure capable of
sustaining the imposed load. However, there are conditions where the use of a harness
and lanyard would be required along with a guardrail, such as in aerial lift or scaffold.

If subjected to in-service loading, remove from service and dont use again;
Safety belt and lanyard - 4,000 pounds of tensile load;
Lifeline secured above the employees workplace to an anchorage or structural
member withstand dead weight of 5,400 pounds;
A lifeline at least -inch manila rope or equivalent with not less than 5,400 footpounds breaking strength;
A lanyard at least inch nylon rope or equivalent;
Free fall less than 6 feet or no contact with lower surface;
Store equipment in clean, dry area and away from excessive heat and freezing.

Note: See Appendix E for PPE Assignment, Training and Fit List Form
See Appendix F for PPE Policy

Appendix A-1

Certification of
Safety-Related
Personal Protective Equipment
Hazard Assessment
Employer:

_________________________________________________
_________________________________________________

Location*:

_________________________________________________
_________________________________________________
_________________________________________________
*Or type of work for employees not assigned to a fixed location

Workplace
Assessed/
Evaluated:

_________________________________________________

Date(s):

_________________________________________________

_________________________________________________

_________________________________________________
Name of Person
Assessing/

_________________________________________________
_________________________________________________

This document certifies that the hazard assessment has been

performed as required by MIOSHA General Industry Safety
Standards, Part 33, Personal Protective Equipment.
Signature of
Person Certifying:

__________________________________________________

Appendix A-2
Personal Protective Equipment Types
Face and Eye Protection
Spectacles w/
No side shield
Half side shield
Full side shield
Detachable side shield
Non-removable lens
Lift front
Headband temple
Cover goggles w/
No ventilation
Indirect ventilation
Direct ventilation

Welding Helmets
Burning Goggles
Welding Helmets w/
Stationary window
Lift front window
Hand held

Helmets by Type:
Type 1: Full brim 1.25
side
Type 2: No brim,
forward peak
Helmets by Class:

(See MIOSHA, General Industry

Safety Standard, Part 33, Personal
Protective Equipment, Table 2)

Cut goggles w/
Direct ventilation
Indirect ventilation

Class A General service

w/limited voltage protection
Class B Utility service w/high
voltage protection
Class C Special service
No voltage protection
Class D Fire fighters full brim
w/ear flaps and chin strap

Face Shield
(See MIOSHA, General Industry
Safety Standard Part 33, Personal
Protective Equipment, Table 1)
Foot and Leg

Head Protection

Hair enclosures

Electrical Protection*

Fall Protection

Safety shoes/boots w/
Impact resistant toe
Metal insoles
Metatarsal guards
Chemical Resistant
Electrical protection
Wet slippery surfaces
Cold weather protection

Insulating Blankets
Matting
Covers
Line Hose
Gloves
Sleeves
Hot Stick

Safety Belts*

Leggings
Molten metal and welding

*Must be capable of withstanding

imposed voltage

*No safety belts for fall protection

after 1-1-98.

Arm and Hand Protection

Body Protection

Safety harnesses
Lifelines
Lanyards

Types
Gloves
Hand Pads
Sleeves
Wristlets

Types
Vests
Jackets
Aprons
Coveralls
Full Body Suits

Appendix B-1
PERSONAL PROTECTIVE EQUIPMENT
HAZARD ASSESSMENT

Company Name: ____________________________________________Date of Assessment: _____________________

Company Address: _________________________________________________________________________________
Workplace Evaluated: ______________________________________________________________________________
Name of Person Completing Assessment: ________________________________________________________________________
Job Classification
WORKSTATION

HAZARD
SOURCE/TYPE

BODY PART
AFFECTED

PPE REQUIRED
YES/NO

TYPE of PPE REQUIRED

Appendix B-2

Appendix B-3
Sample PPE Assessment and Certification Worksheet
(Note) This worksheet, or any other worksheet used to assess the worksite for PPE is not mandatory. However,
certification that a PPE assessment has been completed is required by the PPE standard.)
Assessment conducted by:________________________________________ Date:___________________________
Task_________________________________________________________ Department______________________
Instructions
1.

Conduct a Job Safety Analysis of the above task.

2.

List below the hazards found in the JSA.

3.

If engineering or management practices cannot eliminate the hazards or are not feasible, determine the appropriate PPE for each hazard.
Note: If you are not sure about appropriate PPE, consult your OR-OSHA consultant or insurer for assistance.

Summary of Task Hazards and PPE Required

Impact by:_____materials_____equipment_____objects_____co-worker_____other (describe)_____________________________________
PPE required: (head, eye, foot, etc.)_____________________________________________________________________________
Contact with: _____ Stationary object _____moving object_____sharp object_____other (describe)_________________________________
PPE required: (foot, head, etc.)_________________________________________________________________________________
Fall: _____ from elevation _____ to surface _____slipping _____ tripping _____ other (describe)__________________________________
PPE required: (fall, restraint systems)________________________________________________________
Caught in, under, between: _____ running or meshing objects _____ moving object _____ stationary object _____ rolling vehicle_________
collapsing materials/cave-in _____ other (describe) _______________________________________________________________________
PPE Required: (hand, foot, etc.) _______________________________________________________________________________
Overexposure: ____ noise ____ heat ____ cold____ temperature variation ____ radiation. List dBA ___________Temp ______________F.
PPE required: (hearing, respiratory, clothing, eye, etc.) __________________________________________
Inhalation of: ____hot ____cold ____dust ____mists ____vapors ____smoke ____gasses ____fibers ____biohazards____ _other (describe)
PPE required: (respiratory, face, etc.)_________________________________________________________
Ingestion of: _____hot _____cold _____acids _____bases _____caustics _____poisons _____dust _____mists______ vapors ______smoke
_____gases _____radiation _____fibers _____other (describe) ______________________________________________________________
PPE Required: (respiratory, face, etc.) __________________________________________________________________________
Absorption of: ___acids ___bases ___ caustics ____poisons ___hazardous chemicals ___other (describe) ____________________________
PPE required: (hand, face, eye, clothing, etc.) _____________________________________________________________________
Skin contact with: ___ hot liquid ___molten metal ___sparks ___acids ___bases ___caustics ___poison ___other (describe) _____________
PPE required: (hand, foot, face, eye, clothing, etc.) _________________________________________________________________
4.

Reference the associated MSDS for each hazardous chemical used and list the recommended PPE for that chemical.
Chemical:

MSDS PPE:

Certification _________________________________________ _________________________________

Signature
Date

Appendix B-4
Sample PPE Walk Through Survey and Certification
Department _____________________ Task _________________________________________Date _________
Assess each task for hazards using the following criteria: (1) Type of injury or illness possible: (2) Probability
unlikely, likely, highly likely; and (3) Severity death, serious injury/illness, not serious injury/illness.
1. Sources of motion machinery, processes, tools, materials, people, etc. ______________________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
2. Sources of high temperatures that could cause burns, ignition, injury to eyes, etc. ____________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
3. Sources of chemical exposure splash, vapor, spray, immersion, etc.________________________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
4. Sources of harmful atmospheres dust, fumes, gasses, mists, vapors, fibers, etc._______________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
5. Sources of light radiation welding, brazing, cutting, furnaces, heat treating, high intensity lights, etc._____
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
6. Sources of falling objects materials, equipment, tools, etc.________________________________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
7. Sources of sharp objects which could pierce the skin feet, hands, face, etc. _________________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
8. Sources of rolling or pinching that could crush hands, feet. _____________________________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
9. Layout of workplace and location of co-workers adequate space for task. ___________________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
10. Sources of contact with electricity wires, grounding. ____________________________________________
____________________________________________________________________________________________
Required PPE: _______________________________________________________________________________
I certify that I have conducted a workplace survey on the above task to assess the need for personal protective
equipment. The personal protective equipment noted above will be required while performing this task.
____________________________________________
Signature

____________________________________
Date

Appendix C

PPE TRAINING CERTIFICATION

Trained in PPE
Name

Date

Employee
Number

Trainer

Eye
&
Face

Head

Foot
&
Leg

Hand
&
Arm

Body

Electrical

Fall

Appendix D
Sample Personal Protective Equipment (PPE) Test
(Supervisors should give this test after training the employee on the proper use and care of PPE. The
supervisor should review the test and discuss any areas requiring additional training. When the
supervisor is confident that the employee has an adequate knowledge and ability to properly use PPE
associated with the job, the supervisor should certify training.)
1. List the type(s) of PPE required for your task.

2. What are the hazards you are being protected against for each type of PPE used in your job?

3. Describe procedures for the use and care of the PPE you are using.

4. What should you look for to determine if the PPE you are using is in good working order?

5. What actions do you take when your PPE becomes defective?

Certification
I have personally trained ________________________________ and answered all questions pertaining to the proper use and care
Of PPE. I certify that he/she has adequate knowledge and ability to proper use and care for the PPE associated with his/her job.
__________________________________________
Supervisors Signature

________________________
Date

I have been adequately trained on the use and care of PPE to be used by me. My supervisor has answered all questions to my
satisfaction and I understand he/she will be available for follow-up training if needed.

____________________________________
Employees Signature

______________________
Date

Appendix E

PERSONAL PROTECTIVE EQUIPMENT

ASSIGNMENT, TRAINING AND FIT-TEST FORM
All affected employees receive PPE training that includes when PPE is necessary; what PPE is
necessary and why; how to wear PPE properly; PPE limitations and capabilities; and PPE care
and maintenance. Each affected employee is fitted properly with the assigned PPE.
The following individual has been assigned PPE, has been fit-tested, and has received training.
Employee: ____________________Training Date ______________________________________
Name of Trainer_________________________________________________________________
The following is a list of PPE assigned to this employee including the manufacturer, model and any
identification numbers:

I acknowledge that I have been assigned the above named equipment, have had the opportunity to be
properly fitted, and have received training. I also acknowledge that I understand the training that was
provided:
___________________________________________
(Employees Signature)

Appendix F
PERSONAL PROTECTIVE EQUIPMENT POLICY
FOR
__________________________________
(Name of Company)

PURPOSE
The purpose of this program is to protect the employees of _______________________ (Insert name of
Company) from the occupational hazards within the workplace by providing the proper personal
protective equipment (PPE). It is the goal of the company to use engineering controls as the primary
method for protecting employees. However, when additional protection is necessary, appropriate PPE
will be worn. The scope of this program includes PPE for eye; face, head, foot, and hand protection. If
respirators and/or hearing protection is necessary, their use will be covered by the Companys
Respiratory Protection Program and the Hearing Conservation Program, respectively.

RESPONSIBILITY
The person responsible for coordinating this program is ______________________, (insert name or job
title of responsible person). This person will ensure that hazard assessments are conducted, appropriate
PPE is assigned, and affected employees receive training. The responsible person will also be in charge
of maintaining the documentation for this program.
Department supervisors should advise the responsible person of changes in PPE requirements (e.g., new
procedures/processes requiring different PPE; omission of a job/task). Additionally, supervisors should
consult with the responsible person before purchasing any new PPE.

HAZARD ASSESSMENTS
Each job/task performed will be assessed to determine foot, head, eye, face, and hand hazards present
and the proper PPE that should be worn. The assessments will include observation of the following
sources of hazards:
1.
2.
3.
4.
5.
6.
7.

Impact: Flying chips, objects, dirt, particles, collision, and motion hazards.
Penetration: Falling/dropping objects, sharp objects that cut or pierce.
Compression: Rollover or pinching.
Chemical: Splashing, burns, fumes.
Temperature Extremes: Sparks, splashes from molten materials, burns from high/low
temperatures.
Harmful Dust: Dirt, particles, asbestos, lead.
Light Radiation: Welding, cutting brazing, lasers, furnaces, lights.

The attached Hazard Assessment Form will be completed for each job/task and will serve as certification
that a hazard assessment has been performed.
The person conducting the hazard assessment will also survey jobs that are non-routine or periodic. In
some cases these assessments may not be completed until the jobs are scheduled.
Hazard assessments will be updated/evaluated whenever conditions or procedures change.

Michigan Occupational Safety & Health Administration

Consultation Education & Training Division
7150 Harris Drive, P.O. Box 30643
Lansing, Michigan 48909-8143
For further information or to request consultation, education and training services
call (517) 322-1809
or
visit our website at www.michigan.gov/miosha

www.michigan.gov/lara

LARA is an equal opportunity employer/program. Auxiliary aids, services and other

reasonable accommodations are available upon request to individuals with disabilities.