Scribd
Upload
179 views

PIC Programmer Using Arduino

This Arduino program defines functions for programming PIC microcontrollers using an Arduino board. It defines pins for clock, data, power (VPP), and programming (PGM) signals. Functions are provided to write/read bits, load/write data, erase/program memory, increment addresses, and end programming. The program allows programming PICs in serial using simple commands sent over Serial.

Uploaded by

ganesh
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
179 views

PIC Programmer Using Arduino

This Arduino program defines functions for programming PIC microcontrollers using an Arduino board. It defines pins for clock, data, power (VPP), and programming (PGM) signals. Functions are provided to write/read bits, load/write data, erase/program memory, increment addresses, and end programming. The program allows programming PICs in serial using simple commands sent over Serial.

Uploaded by

ganesh
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 10

/*

PIC programmer using Arduino


This program is distibuted "AS IS", I offer no garantee.
By Ronan Gaillard
*/
#define CLOCK 9
#define DATA 8
#define VPP1 6
#define VPP2 5
#define VPP3 4
#define PGM 10 //HIGH/LOW voltage select mode
#define MCLR 11 //LOW voltage only
void setup() {
pinMode(CLOCK, OUTPUT);
pinMode(VPP1, OUTPUT);
pinMode(VPP2, OUTPUT);
pinMode(VPP3, OUTPUT);
pinMode(DATA, OUTPUT);
pinMode(PGM, OUTPUT);
Serial.begin(9600);
Serial.println("Started");
//Serial.println("Send s to start (please put Vpp first)");
while(true)
{
if (Serial.available() > 0)
{
if(Serial.read()=='s')//HIGH VOLTAGE MODE
{
//VIN should be around 12V max. is 13.5V

digitalWrite(VPP1, HIGH);
digitalWrite(VPP2, HIGH);
digitalWrite(VPP3, HIGH);
Serial.print("D");
break;
}
else//low voltage mode
{
digitalWrite(PGM, LOW);
digitalWrite(VPP1, LOW);
digitalWrite(VPP2, LOW);
digitalWrite(MCLR, LOW);
digitalWrite(VPP3, LOW);

delayMicroseconds(20);
digitalWrite(VPP1, HIGH);
digitalWrite(VPP2, HIGH);
digitalWrite(VPP3, HIGH);
delayMicroseconds(3);
digitalWrite(PGM, HIGH);
delayMicroseconds(3);
digitalWrite(MCLR, HIGH);
Serial.print("D");
break;
}
}
}
}
void loop() {
char command = '\0';
if (Serial.available() > 0) {
command = Serial.read();
switch(command)
{
case 'b' :
BulkEraseProgramMemory();
Serial.print('D');
break;
case 'E' :
EndOfProgramming();
Serial.print('D');
break;
case 'r' :
char valeur[16];
ReadDataFromProgramMemory(valeur);
for(int i=0; i<14;i++)
{
Serial.print(valeur[i]);
}
//Serial.print("D");
break;
case 'l' :

char WritingValue[14];
for(int i=0;i<14;i++)
{
while(Serial.available() == 0)
{
}
WritingValue[i] = Serial.read();
}

LoadDataCommandForProgramMemory(WritingValue);

Serial.print('D');
break;
case 'w' :
BeginProgrammingOnlyCycle();
Serial.print('D');
break;
case 'W' :
BeginEraseProgrammingCycle();
Serial.print('D');
break;
case 'i' :
IncrementAddress();
Serial.print('D');
break;
case 'c' :
char ConfigValue[14];
for(int i=0;i<14;i++)
{
while(Serial.available() == 0)
{
}
ConfigValue[i] = Serial.read();
}
LoadConfiguration(ConfigValue);
BeginProgrammingOnlyCycle();
Serial.print('D');
break;
case 'R' :

digitalWrite(VPP1, LOW);
digitalWrite(VPP2, LOW);
digitalWrite(VPP3, LOW);
delay(3);
digitalWrite(VPP1, HIGH);
digitalWrite(VPP2, HIGH);
digitalWrite(VPP3, HIGH);
Serial.print("D");
break;

}
}

}
void WriteBit(char nb)
{
digitalWrite(CLOCK, HIGH);
if(nb!='0')
{
digitalWrite(DATA,HIGH);
}
delayMicroseconds(3);
digitalWrite(CLOCK, LOW);
delayMicroseconds(3);
digitalWrite(DATA,LOW);
}
byte ReadBit()
{
byte valeur = 0;
digitalWrite(CLOCK, HIGH);
delayMicroseconds(3);
if(digitalRead(DATA)==HIGH)
{
valeur = '1';
}
else
{

valeur = '0';
}
digitalWrite(CLOCK, LOW);
delayMicroseconds(3);
return valeur;
}
void ReadDataFromProgramMemory(char valeur[])
{
digitalWrite(DATA,LOW);
//Command
WriteBit('0');
WriteBit('0');
WriteBit('1');
WriteBit('0');
WriteBit('0');
WriteBit('0');
pinMode(DATA, INPUT);
delayMicroseconds(3);
//DATA
ReadBit();
for(int i =13;i>=0;i--)
{
valeur[i] = ReadBit();
}
ReadBit();

pinMode(DATA, OUTPUT);

}
void LoadDataCommandForProgramMemory(char valeur[])
{
digitalWrite(DATA,LOW);
//Command
WriteBit('0');
WriteBit('1');
WriteBit('0');
WriteBit('0');

WriteBit('0');
WriteBit('0');

delayMicroseconds(3);
//DATA
WriteBit('0');//always 0
for(int i =13;i>=0;i--)
{
WriteBit(valeur[i]);
}
WriteBit('0');//always 0 (stop bit)
delayMicroseconds(3);

}
void BeginProgrammingOnlyCycle()
{
digitalWrite(DATA,LOW);
WriteBit('0');
WriteBit('0');
WriteBit('0');
WriteBit('1');
WriteBit('1');
WriteBit('0');

delayMicroseconds(3);

delay(20);
}
void BeginEraseProgrammingCycle()
{
digitalWrite(DATA,LOW);
WriteBit('0');

WriteBit('0');
WriteBit('0');
WriteBit('1');
WriteBit('0');
WriteBit('0');

delayMicroseconds(3);

delay(20);
}
void BulkEraseProgramMemory()
{
digitalWrite(DATA,LOW);
WriteBit('1');
WriteBit('0');
WriteBit('0');
WriteBit('1');
WriteBit('0');
WriteBit('0');

delayMicroseconds(3);

delayMicroseconds(3);
delay(20);
}
void FullEraseProgramMemory()
{
char Erase [] = {'1','1','1','1','1','1','1','1','1','1','1','1','1','1'};
LoadDataCommandForProgramMemory(Erase);
BulkEraseProgramMemory();
BeginProgrammingOnlyCycle();
}
void IncrementAddress()
{
digitalWrite(DATA,LOW);

WriteBit('0');
WriteBit('1');
WriteBit('1');
WriteBit('0');
WriteBit('0');
WriteBit('0');

delayMicroseconds(3);
}
void LoadDataCommandForDataMemory(char valeur[])
{
digitalWrite(DATA,LOW);
//Command
WriteBit('1');
WriteBit('1');
WriteBit('0');
WriteBit('0');
WriteBit('0');
WriteBit('0');

delayMicroseconds(3);
//DATA
WriteBit('0');//always 0
for(int i =13;i>=0;i--)
{
WriteBit(valeur[i]);
}
WriteBit('0');//always 0 (stop bit)
delayMicroseconds(3);

}
void LoadConfiguration(char valeur[])
{
digitalWrite(DATA,LOW);

//Command
WriteBit('0');
WriteBit('0');
WriteBit('0');
WriteBit('0');
WriteBit('0');
WriteBit('0');

delayMicroseconds(3);
//DATA
WriteBit('0');//always 0
for(int i =13;i>=0;i--)
{
WriteBit(valeur[i]);
}
WriteBit('0');//always 0 (stop bit)
delayMicroseconds(3);

}
void EndOfProgramming()
{
digitalWrite(DATA,LOW);
//Command
WriteBit('1');
WriteBit('1');
WriteBit('1');
WriteBit('0');
WriteBit('1');
WriteBit('0');
delayMicroseconds(3);
}

You might also like