2010 Model Year

Scheduled Maintenance Guide

Vehicle Identification Number (VIN):

Owner Name:
Address:

All rights reserved. Reproduction by any means, electronic or mechanical including photocopying,
recording or by any information storage and retrieval system or translation in whole or part is not permitted
without written authorization from Ford Motor Company. Ford may change the contents without notice
and without incurring obligation.
Copyright 2009 Ford Motor Company
Scheduled Maintenance 1

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

FIND YOUR WAY

Todays vehicles are more sophisticated than ever and need to be properly maintained to help ensure they
operate at the highest level.

Additional Information Available on the Web @

www.genuineservice.com
For lots of helpful tips and information on operating, maintaining, and servicing your Ford, Lincoln, or
Mercury vehicle, visit www.genuineservice.com. Youll also find the Ask Ford online expert available 24/7
to answer questions, important warranty information, and resources to record your vehicles service
history online, register with us for important updates and specials, and find out what to do if you need
roadside assistance.

2 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

FIND YOUR WAY

General Owners
Information

Table of Contents

General Owners Information . . . . . . . . . . . . . . . . . . . . . . . . .2

General Maintenance Information . . . . . . . . . . . . . . . . . . . . . .4
Owner Checks and Services . . . . . . . . . . . . . . . . . . . . . . . . . .8

Keep It Genuine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Multi-Point Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Keep It Genuine

Normal Schedule Trucks, Fullsize Vans & SUVs

Normal Schedule
Trucks, Fullsize
Vans & SUVs

. . . . . . . . . . .14

Class A Motorhome, E-Series, Escape, Expedition, Explorer, Explorer

Sport Trac, F-150, F-250/350/450/550, Mariner, Mountaineer,
Navigator, Ranger and Transit Connect

. . . . . . . . . . . . . . . . . . . . . . .29

Crown Victoria, Edge, Focus, Flex, Fusion, Grand Marquis, Milan,

MKS, MKT, MKX, MKZ, Mustang, Taurus, and Town Car

Scheduled Maintenance 3

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Special Operating
Conditions &
Exceptions

Special Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . .41

Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Engine Coolant Change Record . . . . . . . . . . . . . . . . . . . . . . .48

Normal Schedule
Cars & CUVs

Normal Schedule Cars & CUVs

GENERAL MAINTENANCE INFORMATION

Get the most from your vehicle with routine maintenance
Routine maintenance is the best way to help ensure you get the performance, dependability, long life and
resale value you expect from your vehicle. This is exactly why weve put together the Scheduled
Maintenance Guide. It outlines the services required to properly maintain your vehicle and when they
should be performed. The focus is on maintaining your vehicle while its running great, which goes a long
way toward preventing major repairs and expenses later.
Here are a few suggestions to help you get started on the road to routine maintenance:

Familiarize yourself with your vehicle by going through your Owners Guide.
Take a few minutes to review this handy Scheduled Maintenance Guide.
Make it a habit to use this guide to record scheduled maintenance.
Consider your Ford and Lincoln Mercury Dealership for all your vehicles needs.

Protect your warranty!

Routine maintenance is not only the best way to help keep your vehicle running great, its also the best
way to protect your warranty. While maintenance and repair services may be performed by you or
by any automotive service provider you choose, it is your responsibility to see that all scheduled maintenance
is performed and that the materials used meet Ford Engineering specifications. Failure to perform
scheduled maintenance specified in this guide will invalidate warranty coverage on parts affected by the
lack of maintenance. We cant stress enough how important it is to keep records of all maintenance. This guide
will help you do just that. Ford Motor Company will not deny a warranty claim simply because there is
no documentation. However, damage or failures due to neglect or a lack of proper maintenance
are not covered under warranty.

Keeping maintenance records is easy with the Scheduled Maintenance

Guide
Its important to document the maintenance of your vehicle. Every time you bring your vehicle in for
scheduled maintenance, be sure to present this guide and certify the work. Also record the date of service,
mileage at the time of service, and attach your receipt. This will make record keeping easy and,
should your vehicle ever require warranty coverage, you will have all the documentation to show youve
properly maintained it.

Maintenance Interval
Ford Motor Company establishes recommended maintenance intervals based upon engineering testing to
determine the most appropriate mileage to perform the various maintenance services. This protects your vehicle
at the lowest overall cost to you. Ford Motor Company recommends that you not deviate from the
maintenance schedules presented in this Scheduled Maintenance Guide.
4 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

GENERAL MAINTENANCE INFORMATION

see appropriate schedule on page 41.

Engine Coolant Change Interval

6 years or 105,000 miles - change coolant (whichever comes first). Use coolant specified in the Owners Guide
in the Maintenance and Specifications chapter

After initial change - change coolant every 3 years or 45,000 miles (see page 48)

Determine which maintenance schedule to follow

Its important to follow the maintenance schedule that most closely mirrors your driving habits and the
conditions under which you drive. For this reason, the Scheduled Maintenance Guide is divided into two basic
maintenance schedules: the Normal Schedule (further segmented into Trucks, Fullsize Vans & SUVs and
Cars & CUVs) and Special Operating Conditions.
Determining which maintenance schedule is right for you is easy. For the most part, do you drive your
Ford, Lincoln or Mercury vehicle under typical, everyday conditions? If so, follow the Normal Schedule Trucks,
Fullsize Vans & SUVs, or Normal Schedule Cars & CUVs.

Special Operating Conditions

However, if one or more of the Special Operating Conditions outlined below better describes how you
typically operate your vehicle, you will need to perform some maintenance services more often than the Normal
Schedule recommends.

Towing a trailer or carrying heavy loads

Extensive idling and/or driving at low-speeds for long distances
Driving in dusty conditions
Off-road operation
Use of E85 fuel 50% of the time or greater (flex fuel vehicles only)

Important: For further details and information regarding these Special Operating Conditions see page 41.

Scheduled Maintenance 5

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

General Owners
Information

Maximum Oil Change Interval

Normal Schedule: 7,500 miles or 6 months, whichever occurs first.

Special Operating Conditions: 5,000 miles, 6 months, or 200 hours of engine operation, whichever occurs first

GENERAL MAINTENANCE INFORMATION

Exceptions
Some exceptions for specific vehicles and special applications are outlined below. In addition, you will find
further information under Exceptions on page 47.

Engine oil and engine coolant - time and mileage based interval
If youre unsure which maintenance schedule to follow, ask your Ford and Lincoln Mercury Dealership, or
visit the Maintenance area of www.genuineservice.com.

Oils, Fluids and Flushing

In many cases, fluid discoloration is a normal operating characteristic and, by itself, does not necessarily
indicate a concern or that the fluid needs to be changed. However, discolored fluids that also show signs of
overheating and/or foreign material contamination should be inspected immediately by a qualified
expert such as the factory-trained technicians at your Ford or Lincoln Mercury Dealership. Your vehicles oils
and fluids should be changed at the specified intervals or in conjunction with a repair. Flushing is a
viable way to change fluid for many vehicle sub-systems during scheduled maintenance. It is critical that
systems are flushed only with new fluid that is the same as that required to fill and operate the system, or
using a Ford-approved flushing chemical.

Chemicals and Additives

Non-Ford approved chemicals or additives are not required for factory recommended maintenance. In fact,
Ford Motor Company recommends against the use of such additive products unless specifically
recommended by Ford for a particular application.
Your vehicle is very sophisticated and built with multiple complex performance systems. Every manufacturer
develops these systems using different specifications and performance features. Thats why its
important to rely on your Ford or Lincoln Mercury dealership to properly diagnose and repair your vehicle.

When planning your maintenance services, consider your Ford or Lincoln Mercury dealership for all your
vehicles needs.

6 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

GENERAL MAINTENANCE INFORMATION

There are a lot of reasons why visiting your Ford or Lincoln Mercury Dealership for all your service needs
is a great way to help keep your vehicle running great.

Convenience
Many Dealerships have extended evening and Saturday hours to make your service visit more convenient.
Hows that for quality service?

Factory-trained Technicians
Ford and Lincoln Mercury service technicians participate in extensive factory-sponsored certification training to
help them become experts on the operation of your vehicle. Ask your Dealership about the training and
certification their technicians have received.

Genuine Ford and Motorcraft Replacement Parts

Ford and Lincoln Mercury Dealerships use Ford and Motorcraft branded replacement parts. These parts
meet or exceed Ford Motor Companys specifications, and we stand behind them. Maintenance parts installed
at your Ford or Lincoln Mercury dealership carry a nationwide, 12-month, 12,000-mile parts and labor
limited warranty. Your dealer can give you details.

Value Shopping for Your Vehicles Maintenance Needs

Your dealership recognizes the competitive landscape of maintenance and light repair automotive services.
With factory-trained technicians and one-stop service for everything from routine maintenance like oil
changes and tire rotations to your most complex needs, Ford and Lincoln Mercury Dealerships offer outstanding
value.

Scheduled Maintenance 7

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

General Owners
Information

Get the most from your service and maintenance visits

OWNER CHECKS

AND

SERVICES

It is recommended that the following basic maintenance checks and inspections be performed at the
designated time intervals. See your Owners Guide for more information.
Check every month for all vehicles

Check
Check
Check
Check

function of all interior and exterior lights.

tires for wear and proper air pressure, including spare.
engine oil fluid level.
windshield washer fluid level.

Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check

lap/shoulder belts and seat latches for wear and proper operation.
that externally mounted spare tire is properly stowed (tight) (see your Owners Guide).
power steering fluid level, if equipped.
washer spray, wiper operation, and clean all wiper blades (replace blades as necessary).
parking brake for proper operation.
and lubricate all hinges, latches, door check straps (see dealer) and outside locks.
and lubricate upper and lower sliding door tracks, if equipped.
and clean sliding door contact switches, if equipped.
and lubricate door rubber weatherstrips.
and clean body and door drain holes.
safety warning lamps (brake, ABS, airbag, safety belt) for operation.
engine cooling system level and strength.
battery connections and clean if necessary.
clutch fluid level, if equipped.

Check every six months for all vehicles

Retightening lug nuts

On vehicles equipped with dual rear wheels, retighten the wheel lug nuts to the specified torque at 100 miles

(160 km), and again at 500 miles (800 km) of new vehicle operation and after any wheel disturbance
(tire rotation, changing a flat tire, wheel removal, etc.).
Refer to Wheel Lug Nut Torque Specification in your Owners Guide for the proper lug nut torque specification.

8 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

KEEP IT GENUINE
Tires

Keep It Genuine

YOKOHAMA
Proper tire maintenance and replacement are critical to your vehicles performance and helps keep you and
your passengers safe. Only use replacement tires and wheels that are the same size, load index,
speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally
provided by Ford. The recommended tire and wheel size may be found on either the Safety
Compliance Certification Label or the Tire Label which is located on the B-Pillar or edge of the drivers door.
If this information is not found on these labels then you should consult your Ford Dealer. Use of any
tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could
result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Additionally the use of non-recommended tires and wheels could cause steering, suspension, axle or transfer
case/power transfer unit failure. If you have questions regarding tire replacement, see an authorized
dealer. When you need to replace your tires, please visit your Ford or Lincoln Mercury Dealership for name-brand
tires and people who know your vehicle.
If your Ford or Lincoln Mercury dealership sells the name-brand tire, they can also honor the tire
manufacturers warranty.
Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of
use (load, speed, inflation, etc.) the tires experience throughout their lives. In general, tires should be
replaced after 6 years, regardless of tread wear. However, heat caused by hot climates or frequent high loading
conditions can accelerate the aging process and may require the tires to be replaced more frequently.
You should replace your spare tire when you replace your road tires or after 6 years due to aging even if
the tire has not been used.
Scheduled Maintenance 9

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

KEEP IT GENUINE
Batteries

The technicians at your Ford or Lincoln Mercury dealership can determine the health of your vehicles
battery during any service visit. The Motorcraft Tested Tough Max Series with its long-life design outlasted
other long-life batteries by up to 200%. Thats one reason why we stand behind this battery with a
national, 3-year, free replacement warranty and prorated-cost replacement thereafter for up to 100 months
and unlimited mileage. Should your battery need to be replaced, please consider a Motorcraft brand
battery that meets your vehicles Ford Motor Company specifications.

Brakes

Your Ford or Lincoln Mercury Dealership has the right brake parts for your vehicle and their factory-trained
technicians know exactly how to install them. Ford Original Equipment and Motorcraft replacement
brake pads, shoes, rotors and drums meet the stringent standards of Ford Motor Company engineers, and
theyre also Federal Motor Vehicle Safety Standard (FMVSS) compliant. In addition, all Ford Original
Equipment replacement brake pads, shoes, rotors, and drums are vehicle tested for durability and noise
suppression. The right brake parts and installation are essential to proper brake system operation.

10 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

KEEP IT GENUINE
Oil & Lubricants

Keep It Genuine
It is important to follow a regular maintenance schedule for changing your vehicles oil and lubricants.
Motorcraft Oils and Lubricants meet the stringent standards set by Ford Motor Company. Motorcraft Oils
are formulated to reduce engine friction, improve fuel economy, and protect against deposits and wear.
The American Petroleum Industry certifies them, so you know Motorcraft oil stands up to the tests of both
Ford and independent engineers.

Collision
An accident is an upsetting experience and collision repair is often complicated and confusing. Here are a
few pointers to help you better understand the collision repair process and make sure your vehicle is
properly repaired with the right parts. Properly repairing your vehicle will help maintain its value.

Your rights as a consumer

As a consumer, you are within your rights to insist on original equipment replacement parts. These genuine
parts are made by the manufacturer to meet stringent criteria for fit, finish, structural integrity,
corrosion protection and dent resistance, just like the parts that were originally on your vehicle. Insist on
genuine Ford replacement parts.

The collision shop

Many Ford and Lincoln Mercury Dealerships offer collision repair services. Ask your selling dealership about
their capabilities to help with collision repair.

Scheduled Maintenance 11

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

MULTI-POINT INSPECTION
Parts
Genuine Ford Collision Parts are designed, engineered, and warranted by Ford Motor Company. See your
dealer for limited warranty details. They are manufactured to the same specifications as those on your vehicle
when it was built. The right replacement parts will help maintain the value of your vehicle.

Ford recommended scheduled maintenance In order to keep your vehicle running right, it is important to
have the systems on your vehicle checked regularly. This can help identify potential issues and prevent
major problems. Ford Motor Company recommends the following multi-point inspection be performed at every
scheduled maintenance interval to help ensure your vehicle keeps running great.
MULTI-POINT INSPECTION - Recommended at every visit

Check and top-up fluid levels: brake, coolant recovery reservoir, manual and automatic transmission (if equipped

with an underhood dipstick), power steering (if equipped) and window washer
Inspect tires for wear and check air pressure, including spare.
Check exhaust system for leaks, damage, loose parts and foreign material.
Check battery performance.
Check operation of horn, exterior lamps, turn signals and hazard warning lights.
Check radiator, coolers, heater and air conditioning hoses.
Inspect windshield washer spray and wiper operation.
Check windshield for cracks, chips and pitting.
Inspect for oil and fluid leaks.
Inspect engine air filter.
Inspect half shaft dust boots, if equipped.
Check shocks and struts and other suspension components for leaks and damage.
Inspect steering and linkage.
Inspect accessory drive belt(s).
Inspect clutch operation, if equipped.

12 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

MULTI-POINT INSPECTION
Be sure to ask your Ford or Lincoln Mercury Dealership Service Advisor or Technician about the multi-point
vehicle inspection. Its a comprehensive way to perform a thorough inspection of your vehicle. Its
your checklist that gives you immediate feedback on the overall condition of your vehicle. Youll know
whats been checked, whats okay, as well as those things that may require future or immediate attention.
The multi-point vehicle inspection is one more way to keep your vehicle running great!

Keep It Genuine
Scheduled Maintenance 13

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

7,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

15,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Inspect steering linkage, ball joints, suspension,

tie rod ends, driveshaft, and U-joints (lubricate if

equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

14 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

Tires
When your tires need to be replaced, consider visiting your Ford or Lincoln Mercury dealership for
name-brand tires and people who know your vehicle. And if your Ford or Lincoln Mercury dealership sells
the name-brand tire, they can also honor the tire manufacturers warranty.

22,500 miles
DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 15

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Trucks, Fullsize
Vans & SUVs

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

30,000 miles

Change engine oil and replace oil filter

Inspect automatic transmission fluid level on

vehicles if equipped with dipstick. Consult

your dealer for particular requirements.
Replace cabin air filter (if equipped)
Replace climate-controlled seat filter (if equipped)
Replace engine air filter
Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series and Transit Connect)
Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

37,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

16 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

Oil & Lubricants
It is important to stick to a regular maintenance schedule for changing your vehicles oil and lubricants.
Motorcraft Oils and Lubricants meet the stringent standards set by Ford Motor Company. Motorcraft Oils
are formulated to reduce engine friction, improve fuel economy, and protect against deposits and wear.
The American Petroleum Industry certifies them, so you know Motorcraft oil stands up to the tests of both
Ford and independent engineers.

Normal Schedule
Trucks, Fullsize
Vans & SUVs
Scheduled Maintenance 17

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

Batteries
The technicians at your Ford and Lincoln Mercury dealership can determine the health of your vehicles
battery during any service visit. The Motorcraft Tested Tough Max Series with its long-life design outlasted
other long-life batteries by up to 200%. Thats one reason why we stand behind this battery with a
national 3 year, free-replacement and prorated-cost thereafter up to 100 months with unlimited mileage.
Should your battery need to be replaced, consider any one of the batteries that bear the Motorcraft name.

45,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Inspect steering linkage, ball joints, suspension,

tie rod ends, driveshaft, and U-joints (lubricate if

equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

18 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

52,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

60,000 miles

Change engine oil and replace oil filter

Change automatic transmission fluid and filter on

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 19

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Trucks, Fullsize
Vans & SUVs

all vehicles equipped with the TorqShift

transmission. Consult your dealer for your particular
requirements.
Replace cabin air filter (if equipped)
Replace climate-controlled seat filter (if equipped)
Replace engine air filter
Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series and Transit Connect)
Replace wheel bearing grease and grease seals
on 4x2 front wheel bearings (if non-sealed
bearings)
Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

Brakes
Technicians at your Ford or Lincoln Mercury dealer can install the right brake parts for your vehicle. Ford
Original Equipment and Motorcraft replacement brake pads, shoes, rotors, and drums meet the stringent
standards of Ford Motor Company engineers.
In addition, all Ford Original Equipment replacement brake pads, shoes, rotors, and drums are vehicle
tested for durability and noise suppression while being Federal Motor Vehicle Safety Standard (FMVSS)
compliant. The right brake parts and repair work are essential to ensure your brake system operates as it should.

67,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

20 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

75,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Inspect steering linkage, ball joints, suspension,

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

82,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 21

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Trucks, Fullsize
Vans & SUVs

tie rod ends, driveshaft, and U-joints (lubricate if

equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

90,000 miles

Change engine oil and replace oil filter

Inspect automatic transmission fluid level on

vehicles if equipped with dipstick. Consult

your dealer for your particular requirements.
Replace cabin air filter (if equipped)
Replace climate-controlled seat filter (if equipped)
Replace engine air filter
Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series and Transit Connect)
Replace spark plugs
Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect accessory drive belts
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

97,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

22 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

105,000 miles

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

Normal Schedule
Trucks, Fullsize
Vans & SUVs

Change engine oil and replace oil filter

Change manual transmission fluid (except Escape)
Replace cabin air filter (if equipped)
Change rear axle fluid only on vehicles equipped
with DANA axles (see Special Operating
Conditions on page 41 and Exceptions on page
47)
Change engine coolant (see Engine Coolant
Change Interval on page 6 and Coolant
Change Record on page 48)
Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

112,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 23

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

120,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Replace climate-controlled seat filters (if
equipped)

Replace engine air filter

Replace fuel filter (except Escape, Mariner,

F-Series [non Super Duty],

Expedition/Navigator [short wheel base only],
E-Series and Transit Connect)
Change automatic transmission fluid and filter on
all vehicles equipped with the TorqShift
transmission. Consult your dealer for your particular
requirements.
Replace wheel bearing grease and grease seals
on 4x2 front wheel bearings (if non-sealed
bearings)
Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
Torque the rear U-bolts Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect accessory drive belts
Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

24 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

127,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

135,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Inspect steering linkage, ball joints, suspension,

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 25

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Trucks, Fullsize
Vans & SUVs

tie rod ends, driveshaft, and U-joints (lubricate if

equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

142,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

Tires
When your tires need to be replaced, consider visiting your Ford or Lincoln Mercury dealership for
name-brand tires and people who know your vehicle. And if your Ford or Lincoln Mercury dealership sells
the name-brand tire, they can also honor the tire manufacturers warranty.

26 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

150,000 miles

Change engine oil and replace oil filter

Change engine coolant (see Engine Coolant

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 27

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Trucks, Fullsize
Vans & SUVs

Change Interval on page 6 and Coolant

Change Record on page 48)
Replace cabin air filter (if equipped)
Replace climate-controlled seat filter (if equipped)
Replace engine air filter
Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series and Transit Connect)
Change automatic transmission fluid and filter
(filter not required on 6F35). (Except vehicles
equipped with the TorqShift transmission).
Change manual transmission fluid
Change rear axle lubricant on all rear wheel
drive (RWD) vehicles (see pages 41 and
47).
Change transfer case fluid (4x4 only)
Change front differential fluid (4x4 only)
Replace wheel bearings (if non-sealed bearings)
Replace accessory drive belt(s) if not
replaced in the last 100,000 miles (160,000 km)
Inspect steering linkage, ball joints, suspension, tie
rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
Torque the rear U-bolts (Transit Connect only)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect and lubricate 4x4 front axle U-joints
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

NORMAL SCHEDULE TRUCKS, FULLSIZE VANS & SUVS

Brakes
Technicians at your Ford or Lincoln Mercury dealer can install the right brake parts for your vehicle. Ford
Original Equipment and Motorcraft replacement brake pads, shoes, rotors, and drums meet the stringent
standards of Ford Motor Company engineers.
In addition, all Ford Original Equipment replacement brake pads, shoes, rotors, and drums are vehicle
tested for durability and noise suppression while being Federal Motor Vehicle Safety Standard (FMVSS)
compliant. The right brake parts and repair work are essential to ensure your brake system operates as it should.

28 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE CARS & CUVS

7,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

15,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Inspect and lubricate steering linkage, ball joints,

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

Normal Schedule
Cars & CUVs

suspension, tie rod ends, driveshaft and U-joints

(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

Scheduled Maintenance 29

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE CARS & CUVS

Tires
When your tires need to be replaced, consider visiting your Ford or Lincoln Mercury dealership for
name-brand tires and people who know your vehicle. And if your Ford or Lincoln Mercury dealership sells
the name-brand tire, they can also honor the tire manufacturers warranty.

22,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

30 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE CARS & CUVS

30,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Replace climate-controlled seat filter (if equipped)
Replace engine air filter
Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect transmission fluid level (if equipped with
an underhood dipstick).
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

37,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 31

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Cars & CUVs

tread depth

Inspect the wheels and related components for

NORMAL SCHEDULE CARS & CUVS

45,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Inspect and lubricate steering linkage, ball joints,

suspension, tie rod ends, driveshaft and U-joints

(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

Batteries
The technicians at your Ford and Lincoln Mercury dealership can determine the health of your vehicles
battery during any service visit. The Motorcraft Tested Tough Max Series with its long-life design outlasted
other long-life batteries by up to 200%. Thats one reason why we stand behind this battery with a
national 3 year, free-replacement and prorated-cost thereafter up to 100 months with unlimited mileage.
Should your battery need to be replaced, consider any one of the batteries that bear the Motorcraft name.

32 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE CARS & CUVS

52,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

60,000 miles

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 33

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Cars & CUVs

Change engine oil and replace oil filter

Replace climate-controlled seat filter (if equipped)
Replace cabin air filter (if equipped)
Replace engine air filter
Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect transmission fluid level (if equipped with
an underhood dipstick).
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

NORMAL SCHEDULE CARS & CUVS

67,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

75,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Inspect and lubricate steering linkage, ball joints,

suspension, tie rod ends, driveshaft and U-joints

(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect transmission fluid level (if equipped with
an underhood dipstick)
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

82,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

34 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE CARS & CUVS

90,000 miles

Change engine oil and replace oil filter

Replace climate-controlled seat filter (if equipped)
Replace engine air filter
Replace cabin air filter (if equipped)
Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
Replace spark plugs
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect accessory drive belt(s)
Inspect transmission fluid level (if equipped with
an underhood dipstick).
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

97,500 miles
DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 35

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Cars & CUVs

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

NORMAL SCHEDULE CARS & CUVS

105,000 miles

Change engine oil and replace oil filter

Change engine coolant (see Engine Coolant

Change Interval on page 6 and Engine

Coolant Change Record on page 48)
Replace cabin air filter (if equipped)
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect transmission fluid level (if equipped with
an underhood dipstick)
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

112,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

36 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE CARS & CUVS

120,000 miles

Change engine oil and replace oil filter

Replace climate-controlled seat filter (if equipped)
Replace engine air filter
Replace cabin air filter (if equipped)
Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect accessory drive belt(s)
Inspect transmission fluid level (if equipped with
an underhood dipstick).
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

Normal Schedule
Cars & CUVs
Scheduled Maintenance 37

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE CARS & CUVS

Oil & Lubricants
It is important to stick to a regular maintenance schedule for changing your vehicles oil and lubricants.
Motorcraft Oils and Lubricants meet the stringent standards set by Ford Motor Company. Motorcraft Oils
are formulated to reduce engine friction, improve fuel economy, and protect against deposits and wear.
The American Petroleum Industry certifies them, so you know Motorcraft oil stands up to the tests of both
Ford and independent engineers.

127,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag

Perform multi-point inspection (recommended)

RO#:

P&A CODE:

DATE:

MILEAGE:

38 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

NORMAL SCHEDULE CARS & CUVS

135,000 miles

Change engine oil and replace oil filter

Replace cabin air filter (if equipped)
Inspect and lubricate steering linkage, ball joints,

suspension, tie rod ends, driveshaft and U-joints

(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Inspect transmission fluid level (if equipped with
an underhood dipstick)
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

142,500 miles

Change engine oil and replace oil filter

Inspect cabin air filter (if equipped)
Rotate tires, inspect tires for wear and measure

DEALER VALIDATION:

tread depth

Inspect the wheels and related components for

abnormal noise, wear, looseness, or drag
RO#:

P&A CODE:

DATE:

MILEAGE:

Scheduled Maintenance 39

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Normal Schedule
Cars & CUVs

Perform multi-point inspection (recommended)

NORMAL SCHEDULE CARS & CUVS

150,000 miles

Change engine oil and replace oil filter

Change engine coolant (see Engine Coolant

Change Interval on page 6 and Engine

Coolant Change Record on page 48)
Change automatic transmission fluid
Replace automatic transmission fluid filter (except
5F55, 6F35 and AWF-21 transaxles)
Change manual transmission fluid
Replace rear axle lubricant on all rear wheel
drive (RWD) vehicles (see pages 41 and
47).
Replace climate-controlled seat filter (if equipped)
Replace engine air filter
Replace cabin air filter (if equipped)
Replace fuel filter (Crown Victoria, Grand
Marquis, Town Car and Mustang)
Replace accessory drive belt(s) if not replaced in
the last 100,000 miles (160,000 km)
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft and U-joints
(lubricate if equipped with grease fittings)
Inspect engine cooling system and hoses
Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
Inspect half shaft boots (if equipped)
Inspect exhaust system and heat shields
Rotate tires, inspect tires for wear and measure
tread depth
Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
Perform multi-point inspection (recommended)

DEALER VALIDATION:

RO#:

P&A CODE:

DATE:

MILEAGE:

40 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

SPECIAL OPERATING CONDITIONS

Items Needing Special Attention
If you operate your Ford/Lincoln/Mercury vehicle primarily in one of the more demanding Special
Operating Conditions listed below, you will need to have some items maintained more frequently. If you
only occasionally operate your vehicle under these conditions, it is not necessary to perform the
additional maintenance. For specific recommendations, see your Ford or Lincoln Mercury Dealership Service
Advisor or Technician.
Towing a trailer or using a camper or car-top carrier
Inspect frequently, service as Inspect and lubricate U-joints.
required.
See axle maintenance items under Exceptions.
Every 5,000 miles Rotate tires, inspect tires for wear and measure
tread depth.
Inspect the wheels and related components for
abnormal noise, wear, looseness or drag.
Every 5,000 miles or 6 months Change engine oil and replace oil filter.
Inspect and lubricate U-joints.
Every 30,000 miles Change automatic transmission fluid (not required
on 6R60/6R80/TorqShift transmissions).
Replace wheel bearing grease and grease seals on
4x2 front wheel bearings (if non-sealed bearings are
used).
Every 60,000 miles Change transfer case fluid.
Change manual transmission fluid.

Special Operating
Conditions &
Exceptions
Scheduled Maintenance 41

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

SPECIAL OPERATING CONDITIONS

Extensive idling and/or low-speed driving for long distances as in
heavy commercial use such as delivery, taxi, patrol car or livery
Inspect frequently, service as Replace cabin air filter.
required
Every 5,000 miles Inspect brake system.
Rotate tires, inspect tires for wear and measure
tread depth.
Inspect the wheels and related components for
abnormal noise, wear, looseness or drag.
Lubricate control arm and steering ball joints (if
equipped with grease fittings).
Every 5,000 miles or 6 months Inspect and lubricate U-joints.
Every 5,000 miles, 6 months or Change engine oil and replace oil filter.
200 hours of engine operation
Every 15,000 miles Replace fuel filter (Crown Victoria, Grand Marquis,
Town Car, Mustang, Ranger, F-Super Duty, Expedition
EL and Navigator EL).
Every 30,000 miles Change automatic transmission fluid (not required
on 6R60/6R80/TorqShift transmissions).
Replace wheel bearing grease and grease seals on
4x2 front wheel bearings (if non-sealed bearings are
used).
Every 60,000 miles Replace spark plugs.
Change transfer case fluid.

42 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

SPECIAL OPERATING CONDITIONS

Crown Victoria Police Interceptor & Taxi, and Executive Series Town
Car equipped with Engine Idle Hour Meter
Inspect frequently, service as Replace cabin air filter (if equipped).
required
Every 5,000 miles Inspect brake system.
Rotate tires, inspect tires for wear and measure
tread depth.
Inspect the wheels and related components for
abnormal noise, wear, looseness or drag.
Lubricate control arm and steering ball joints (if
equipped with grease fittings).
Every 5,000 miles or 6 months Inspect and lubricate U-joints.
Every 5,000 miles, 6 months or Change engine oil and replace oil filter (see
as indicated by time/mileage description below).
calculation
Every 15,000 miles Replace fuel filter.
Every 30,000 miles Change automatic transmission fluid.
Every 60,000 miles Replace spark plugs.

Scheduled Maintenance 43

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Special Operating
Conditions &
Exceptions

ENGINE IDLE HOUR METER (IF EQUIPPED):

Your vehicle may be equipped with an idle meter to indicate how much time the vehicle is idling in P (Park)
or N (Neutral). The meter is incorporated with the vehicle odometer. Depressing the odometer-reset button
once will display the trip odometer (miles followed by a T for trip odometer). Depressing the odometer-reset
button a second time will display the idle meter (hours followed by an H for hours). The idle meter
only accumulates time when the vehicle is in P (Park) or N (Neutral). Displayed time is cumulative for the
vehicle. It cannot be reset to zero. Police/Fleet vehicles often experience long periods of idling, during which
engine oil will continue to break down but mileage is not accumulated on the odometer.
To assist fleet managers in maintaining proper oil change intervals, the idle meter will help determine when
an oil change is required. For every hour that the vehicle idles, it has accumulated the equivalent of
approximately 33 miles of driving. Using the combination of the vehicle odometer and idle meter allows
the fleet manager to better determine when the oil needs to be changed
Engine idle hour meter calculation:
Idle hours x 33 = miles equivalency
Miles driven + miles equivalency = oil change interval
Example: When the odometer has accumulated 3,000 miles and the idle meter shows 61 hours, a
5,000 mile oil change interval will have been reached: 3,000 road miles + (61 idle hours x 33 miles/idle
hour) = 5,013 miles.

SPECIAL OPERATING CONDITIONS

Operating in dusty conditions such as unpaved or dusty roads
Inspect frequently, service as Replace engine air filter.
required
Replace cabin air filter (if equipped).
Every 5,000 miles Rotate tires, inspect tires for wear and measure
tread depth.
Inspect the wheels and related components for
abnormal noise, wear, looseness or drag.
Every 5,000 miles or 6 months Change engine oil and replace oil filter.
Inspect and lubricate U-joints.
Every 15,000 miles Replace fuel filter (Crown Victoria, Grand Marquis,
Town Car, Mustang, Ranger, F-Super Duty, Expedition
EL and Navigator EL).
Every 30,000 miles Change automatic transmission fluid (not required
on 6R60/6R80/TorqShift transmissions).
Replace wheel bearing grease and grease seals on
4x2 front wheel bearings (if non-sealed bearings are
used).
Every 50,000 miles Change manual transmission fluid.
Change rear axle lubricant (E-450 and F-450/550
only).
Every 60,000 miles Change transfer case fluid.

44 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

SPECIAL OPERATING CONDITIONS

Off-road operation
Inspect frequently, service as Replace cabin air filter (if equipped).
required
Inspect and lubricate steering linkage ball joints
and U-joints (if equipped with grease fittings).
Every 5,000 miles or 6 months Change engine oil and replace oil filter.
Rotate tires, inspect tires for wear and measure
tread depth.
Inspect the wheels and related components for
abnormal noise, wear, looseness or drag.
Every 30,000 miles Change automatic transmission fluid (not required
on 6R60/6R80/TorqShift transmissions).
Replace wheel bearing grease and grease seals on
4x2 front wheel bearings (if non-sealed bearings are
used).
Every 50,000 miles Change manual transmission fluid.
Change rear axle lubricant (E-450 and F-450/550
only).
Every 60,000 miles Change transfer case fluid.
Use of E85 50% of the time or greater (flex fuel vehicles only)
Every 5,000 miles Rotate tires, inspect tires for wear and measure
tread depth.
Inspect the wheels and related components for
abnormal noise, wear, looseness or drag.
Every 3,000 miles If ran exclusively on E85, fill the tank full with
regular unleaded fuel.
Every 5,000 miles or 6 months Change engine oil and replace oil filter.
Special Operating
Conditions &
Exceptions
Scheduled Maintenance 45

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

SPECIAL OPERATING CONDITIONS

Special Operating Conditions Log
DEALER VALIDATION:

DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:
DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:
DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:
DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:
DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:
DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:
DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:
DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:
DEALER VALIDATION:

RO#:
DATE:

P&A CODE:
MILEAGE:

RO#:
DATE:

P&A CODE:
MILEAGE:

46 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

EXCEPTIONS
In addition, there are several exceptions to the Normal Schedule. They are listed below:
Normal Vehicle Axle Maintenance

Rear axles and power take-off (PTO) units containing synthetic lubricant and light duty trucks equipped with
Ford-design axles are lubricated for life. These lubricants are not to be checked or changed unless a leak is suspected,
service is required or the axle assembly has been submerged in water. The axle and PTO lubricant should be
changed anytime the axle and PTO have been submerged in water. During extended trailer tow operation above 70F
ambient and wide open throttle for extended periods above 45 mph, non-synthetic rear axle lubricants
should be replaced every 3,000 miles or 3 months, whichever occurs first. The 3,000 mile lube change interval
may be waived if the axle was filled with 75W140 synthetic gear lubricant meeting Ford specification
WSL-M2C192-A, part number F1TZ-19580-B or equivalent. Add friction modifier C8AZ-19B546-A (EST-M2C118-A)
or equivalent for complete refill of Traction-Lok rear axles (see Owners Guide for quantity). The axle
lubricant should be changed anytime an axle has been submerged in water.

Police/Taxi/Livery Vehicle Axle Maintenance

Replace rear axle lubricant every 100,000 miles. Rear axle lubricant change may be waived if the axle was
filled with 75W140 synthetic gear lubricant meeting Ford specification WSL-M2C192-A, part number FITZ-19580-B
or equivalent. Add four ounces of additive friction modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent for
complete refill of Traction-Lok rear axles. The axle lubricant should be changed anytime the axle has been submerged
in water.

E450 and F450/550 Axle Maintenance

Replace rear axle lubricant every 100,000 miles under normal driving conditions on all E450 and
F450/550 applications. For E450 and F450/550 vehicles operated at or near maximum Gross Vehicle
Weights, the rear axle lubricant should be replaced every 50,000 miles. In addition, this 50,000 mile schedule
should be observed when the vehicles are operated under the Special Operating Conditions, where noted, on
page 41.

California Fuel Filter Replacement

If vehicle is registered in California, the California Air Resources Board has determined that the failure to

Class A Motorhome

Every two years - Change brake fluid

Every 60,000 miles - Change automatic transmission fluid
Scheduled Maintenance 47

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)

Special Operating
Conditions &
Exceptions

perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion
of the vehicles useful life. Ford Motor Company, however, urges you to have all recommended maintenance
services performed at the specified intervals and to record all vehicle service.

ENGINE COOLANT CHANGE RECORD

Current mileage goes here =>
Add 45,000 miles to the current miles
+ 45,000
Next change due at this mileage =>
Or
Todays date goes here =>
Add 3 years + 00 / 00 / 03
Date of next change =>
whichever comes first

Dealer Stamp

Current mileage goes here =>

Add 45,000 miles to the current miles
+ 45,000
Next change due at this mileage =>
Or
Todays date goes here =>
Add 3 years + 00 / 00 / 03
Date of next change =>
whichever comes first

Dealer Stamp

Current mileage goes here =>

Add 45,000 miles to the current miles
+ 45,000
Next change due at this mileage =>
Or
Todays date goes here =>
Add 3 years + 00 / 00 / 03
Date of next change =>
whichever comes first

Dealer Stamp

Current mileage goes here =>

Add 45,000 miles to the current miles
+ 45,000
Next change due at this mileage =>
Or
Todays date goes here =>
Add 3 years + 00 / 00 / 03
Date of next change =>
whichever comes first

Dealer Stamp

P & A CODE
R.O.#

P & A CODE
R.O.#

P & A CODE
R.O.#

P & A CODE
R.O.#

48 Scheduled Maintenance

2010 Scheduled Maintenance Guide (smg)

Scheduled Maintenance Guide, 2nd Printing
USA (fus)