Scribd
Upload
43 views15 pages

First Access To SR: Edit BOF File

This document provides instructions for initial configuration of a router including: 1. Editing the BOF file and adding configuration parameters such as IP address and authentication. 2. Configuring network interface cards and modules by using the configure card and show card/mda commands. 3. Enabling telnet and FTP services to allow remote access to the router. 4. Changing the admin password, router name, and system time for initial device configuration.

Uploaded by

Lo Lanic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
43 views15 pages

First Access To SR: Edit BOF File

This document provides instructions for initial configuration of a router including: 1. Editing the BOF file and adding configuration parameters such as IP address and authentication. 2. Configuring network interface cards and modules by using the configure card and show card/mda commands. 3. Enabling telnet and FTP services to allow remote access to the router. 4. Changing the admin password, router name, and system time for initial device configuration.

Uploaded by

Lo Lanic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 15

First Access to SR

Edit BOF file


Default bof file

primary-image
primary-config
persist
autonegotiate
duplex
speed
wait

cf3:/7750-TiMOS-6.0.R9
cf3:/config.cfg
off
full
100
3

First Access to SR
Edit BOF file

Add the RED text to bof file

primary-image cf3:/7750-TiMOS-6.0.R9
primary-config cf3:/config.cfg
address
10.10.10.1/24 active
autonegotiate
duplex
full
speed
100
wait
3
persist
on
no li-local-save
no li-separate
console-speed 115200

First Access to SR
Edit BOF file
Now insert flash card into Compact Flash#3 and boot up router

First Access to SR
Config CARD and MDA
A:NS074863611# show card

First Access to SR
Config CARD and MDA
A:NS074863611# config card 1
A:NS074863611>config>card# card-type iom-20g-b
*A:NS074863611>config>card# no shutdown
NOW DO SHOW CARD COMMAND AGAIN
*A:NS074863611# show card

First Access to SR
Config CARD and MDA
A:NS074863611# show mda

First Access to SR
Config CARD and MDA
*A:NS074863611# configure card 1
*A:NS074863611>config>card# mda 1
*A:NS074863611>config>card>mda# mda-type m20-1gb-tx
YOU WILL SEE ETHERNET PORT ARE BLINKING
*A:NS074863611>config>card>mda# no shutdown
NOW DO SHOW MDA COMMAND AGAIN
*A:NS074863611# show mda

First Access to SR
Config CARD and MDA
NOW CARD AND MDA ARE READY TO WORK
NOW YOU WILL NEED TO SAVE YOUR WORK
TO SAVE DO ADMIN SAVE COMMAND

First Access to SR
Enable Telnet and Ftp server
Connect Ethernet cable to your PC and Mgmt port on router
On your PC config 10.10.10.2.24 ip address

First Access to SR
Enable Telnet and Ftp server
Question
Can your PC ping router ?
Can your PC telnet to router ?
Can you PC ftp to router ?

First Access to SR
Enable Telnet and Ftp server
ANSWER
Can your PC ping router ?
CAN
Can your PC telnet to router ?
CAN NOT
Can you PC ftp to router ?
CAN NOT

First Access to SR
Enable Telnet and Ftp server
A:NS074863611# configure system security
A:NS074863611>config>system>security# telnet-server
A:NS074863611>config>system>security# ftp-server
A:NAPT_SR1_1>config>system>security>user admin access console ftp
NOW TRY TO TELNET/FTP TO ROUTER

First Access to SR
Change admins password
A:NS074863611# configure system security user admin
A:NS074863611>config>system>security>user# password napteg2

First Access to SR
Change router name
A:NS074863611# configure system name NAPT_SR1_1

First Access to SR
Change system time
A:NAPT_SR1_1# admin set-time 2009/10/26 14:00
CHECK SYSTEM TIME USE SHOW SYSTEM TIME COMMAND
A:NAPT_SR1_1# show system time

You might also like