PNMT - GENERAL

NECITR-YTC
ART-SEP/03 V02

PASOLINK NETWORK MANAGEMENT TERMINAL (PNMT) IS A MOBILE TERMINAL CONSISTING OF A

PORTABLE COMPUTER WITH A SIMPLIFIED VERSION OF THE PASOLINK NETWORK
MANAGEMENT SOFTWARE DEVELOPED FOR MANAGEMENT OF NEC PASOLINK SERIES SHORT
HAUL RADIO TRANSMISSION NETWORK.
PNMT IS DESIGNED AS AN ONSITE MAINTENANCE
TOOL TO BE USED BY THE FIELD ENGINEERS AND
TECHNICIANS. IT CONNECTS DIRECTLY TO THE LA
PORT OF THE PASOLINK IDU. PNMT CAN BE USED
TO MONITOR LOCAL / REMOTE
EQUIPMENT
STATUS AND PROVIDES CONTROL CAPABILITIES
SIMILAR TO THOSE AVAILABLE IN PNMS.
PNMT IS ALSO USED TO DOWN LOAD THE SYSTEM
AND CONFIGURATION FILES TO THE PM CARD AND
UPGRADE THE SOFTWARE IN THE IDU
WHEN CONNECTED TO AN IDU PNMT CAN
MONITOR NOT ONLY THE LOCAL EQUIPMENT BUT
ANY REMOTE NETWORK ELEMENT UNDER THE
CONTROL OF THE CENTRAL PM CARD.
TO USE THE PNMT, PM CARD SHOULD BE
MOUNTED IN THE IDUs.

PNMT

FUNCTIONS

NECITR-YTC
ART-SEP/03 V02

MICROSOFT WINDOWS 98/NT/200/XP WORKSTATION GRAPHICAL USER INTERFACE

ONE HOP LINK DISPLAY ON THE PNMT SCREEN

COMMUNICATE WITH REMOTE PM CARDS ON THE SAME NETWORK

COLLECTS ALARM AND STATUS INFORMATION FROM THE LOCAL AND REMOTE PM CARDS
TRANSMISSION EQUIPMENT CONTROL VIA LOCAL AND REMOTE PM CARDS
SEVERAL LEVELS OF LOGIN / LOGOUT

EVENT LOGGING WINDOW

PERFORMANCE MONITORING FUNCTION WINDOW
LOCAL / REMOTE EQUIPMENT CONTROL FUNCTION

LOCAL/REMOTE PM CARD CONFIGURATION MANAGEMENT

LOCAL/REMOTE UP GRADING OF APPLICATION SOFTWARE

PNMT

PNMT COMMUNICATION INTERFACE

NECITR-YTC
ART-SEP/03 V02

COMMUNICATION BETWEEN THE PNMT AND THE RADIO NETWORK EQUIPMENT CAN BE :
VIA THE LA PORT OF THE LOCAL PASOLINK EQUIPMENT
VIA THE DIGITAL SERVICE CHANNEL DSC TO A REMOTE PASOLINK EQUIPMENT
LA PORT IS LOCATED ON THE FRONT OF THE EQUIPMENT AND
CONSISTS OF A DB15 CONNECTOR. LA PORT CONNECT THE
PM CARD IN THE IDU VIA A SERIAL CABLE TO THE RELEVANT
COMMUNICATION PORT OF THE PNMT COMPUTER.
PROPERTIES OF THE LA PORT ARE AS FOLLOWS:
PORT CONFIGURATION
RS-232
CONNECTOR TYPE
D-SUB 15 (FEMALE)
BITS PER SECOND RATEUP TO 19200

LA PORT

PNMT

HARDWARE/SOFTWARE CONFIGURATION

NECITR-YTC
ART-SEP/03 V02

RECOMMENDED PNMT MOBILE PC CONFIGURATION

LAPTOP PC WITH TFT DISPLAY (IBM COMPATIBLE)
CPU:
PENTIUM-400 OR HIGHER
RAM:
128 MB OR MORE
HDD:
2 GB OR MORE
FDD:
3.5INCH
CD-ROM: 8 x OR HIGHER
INTEGRATED SOUND CARD AND SPEAKER
SOFTWARE CONFIGURATION
ALL STRUCTURED AND MODULAR PROGRAMS USED IN PNMT ARE RESIDENT IN THE HARD-DISK
AND RAM OF THE PERSONAL COMPUTER. THE WINDOWS OPERATING SYSTEM IS EMPLOYED
WHICH IS CAPABLE OF MULTITASK PROCESSING. THE PNMT SOFTWARE BASICALLY CONSISTS
OF TWO PARTS, THE OPERATING SYSTEM AND THE APPLICATION PROGRAM
OPERATING SYSTEM
WINDOWS 98 (ENGLISH VERSION)
WINDOWS NT WORKSTATION Ver 4.0 (ENGLISH VERSION) WITH SP 6.0 OR HIGHER
WINDOWS 2000 (ENGLISH VERSION) WITH SP3 OR HIGHER
WINDOWS XP (ENGLISH VERSION) WITH SP1 OR HIGHER
APPLICATION PROGRAM
NEC PNMT SOFTWARE
IE 5.0 OR HIGHER
ACROBAT READER
PNMT

START UP

NECITR-YTC
ART-SEP/03 V02

CONNECT THE PNMT PC COM1 PORT AND THE PASOLINK IDU LA PORT USING A RS232C CABLE

PREPARATION

DOUBLE CLICK ON THE PNMT SHORTCUT

ICON ON THE DESKTOP OR CLICK ON
START>>PROGRAM>>PNMT>>PNMT

From the Control Panel select Phone

and Modem Options. Add a Standard
19200 bps Modem and assign it to the
COM1 port ( or the COM port to be
used)
Create a Dial-up connection using the
above standard modem and name it
as pnmt
Install the NEC PNMT software
See PNMT Install Manual for details

PNMT PROGRAM STARTUP AND

TRIES TO GET CONNECTED TO
PASOLINK EQUIPMENT USING THE
DIAL-UP CONNECTION PNMT

AFTER CONNECTING TO THE PASOLINK

EQUIPMENT TRIES TO ACQUIRE DATA FROM
THE LOCAL EQUIPMENT AND THE REMOTE
EQUIPMENT TO DISPLAY ON THE LINK
SUMMARY WINDOW

PNMT

SHUT DOWN

NECITR-YTC
ART-SEP/03 V02

IF YOU HAVE NOT LOGIN FIRST THE

EXIT MENU CANNOT BE SELECTED.

TO EXIT THE PNMT PROGRAM

CLICK ON EXIT IN THE SYSTEM
DROPDOWN MENU AND CLICK YES.

IN THE DIALOG BOX

THAT OPENS CLICK
YES

THE SCREEN INDICATES NOW PNMT

SHUTDOWN. IT WILL TAKE FEW MINUTES TO
SHUTDOWN

PNMT

PNMT MAIN SCREEN

NECITR-YTC
ART-SEP/03 V02

PNMT MAIN SCREEN IS SPLIT EVENLY TO DISPLAY THE DATA FROM THE TWO NEs IN THE HOP.
PNMT WINDOW
MENU BAR
COMMON TOOL BAR
LINK SUMMARY WINDOW
NE-SPECIFIC MENU ITEMS

BLOCK DIAGRAM

NE-SPECIFIC DATA

CLICK ON THE ARROW

ICONS IN THE MIDDLE OF
THE SCREEN TO EXPAND
THE LEFT OR RIGHT DATA
FIELD. CLICKING ON THE
BLOCK WILL RETURN THE
ORIGINAL SPLIT SCREEN.

TAB SELECTION FOR

OTHER EQUIPMENT
VIEWS

PNMT

PNMT MAIN SCREEN

NECITR-YTC
ART-SEP/03 V02

COMMON MENU BAR

COMMON MENU BAR OF THE PNMT WINDOW PRESENTS THE SYSTEM AND HELP MENU ITEMS. EACH MENU ITEM
HAVE A DROP DOWN MENU SHOWING THE OPTIONS AVAILABLE.
COMMON TOOL BAR
COMMON TOOL BAR OF THE PNMT WINDOW HOLDS THE ICONS OF THE FREQUENTLY USED MENU ITEMS
LINK SUMMARY WINDOW
LINK SUMMARY WINDOW SHOWS THE SELECTED NETWORK ELEMENT (NE) AND ITS OPPOSITE NE AS A LINK (HOP).
THE SELECTED NE IS SHOWN ON THE LEFT HAND SIDE WINDOW AND THE OPPOSITE NE ON THE RIGHT HAND SIDE
WINDOW OF THE LINK SUMMARY WINDOW. IT SHOWS GRAPHICALLY THE STATUS OF THE PASOLINK EQUIPMENT IN
BLOCK DIAGRAM FORM. NE-SPECIFIC PARAMETERS AND NE-SPECIFIC MENU ITEMS ARE ALSO SHOWN IN THIS
WINDOW
NE SPECIFIC DATA :
NE SPECIFIC DATA ARE SHOWN IN SEVERAL DATA WINDOWS SELECTED BY THE TABS AT THE BOTTOM OF THE
WINDOW OR BY CLICKING THE EQUIPMENT SYMBOLS IN THE BLOCK DIAGRAM. DATA DISPLAYED DEPENDS
ON THE EQUIPMENT TYPE (PASOLINK +, V3, V4, ETC.)
NE SPECIFIC MENU ITEMS:
EQUIPMENT CONFIGURATION

EQUIPMENT SETUP
MAINTENANCE

LINK PERFORMANCE MONITOR

EVENT LOG
TAB SELECTION

DETAILED MONITORING STATUS AND ALARMS OF EACH MAIN UNIT IN THE PASOLINK EQUIPMENT (ODU, IDU, AUX I/P
AND PMC) CAN BE VIEWED BY CLICKING ON THE RELEVANT TAB.

NE BLOCK DIAGRAM:
STATUS OF EACH MAIN UNIT IN THE PASOLINK EQUIPMENT (ODU, IDU, AUX I/P AND PMC) ARE SHOWN IN THE BLOCK
DIAGRAM AS SYMBOLS. WHEN ANY SYMBOL IS CLICKED THE RELATED EQUIPMENT WINDOW OPEN AND SHOWS THE
DETAILS OF ALARM AND STATUS DETAILS AND OTHER PARAMETERS,

PNMT

PNMT WINDOW MENU ITEMS

SYSTEM

REFRESH

NECITR-YTC
ART-SEP/03 V02

HELP

HELP

DISPLAY A LIST OF PNMT MANUALS IN PDF FILE FORMAT

ABOUT

DISPLAY THE PNMT VERSION NUMBER

THIS FUNCTION ENABLES PNMT TO ACQUIRE ALL STATUS MANUALLY
AND TO UPDATE EQUIPMENT INFORMATION
THIS FUNCTION OPEN THE LOGIN/LOGOUT WINDOW TO ENTER THE
USER NAME AND PASSWORD.
THIS FUNCTION OPEN THE PASSWORD CHANGE WINDOW

LOGIN / LOGOUT
CHANGE PASSWORD

THIS FUNCTION IS USED TO ENABLE/DISABLE THE BUZZER FUNCTION AND

DEFINE THE BUZZER SOUND

ALARM BUZZER
CONNECT

THIS FUNCTION IS USED TO DISPLAY THE SUMMARY LIST OF THE NETWORK ELEMENTS IN
THE NETWORK

EXIT
THIS FUNCTION IS USED TO CLOSE THE PNMT PROGRAM

PNMT

NE SPECIFIC MENU ITEMS

CONFIGURATION

EVENT LOG

NECITR-YTC
ART-SEP/03 V02

LINK PERFORMANCE MONITOR

THIS FUNCTION OPEN THE G826 LINK PERFORMANCE INFORMATION WINDOW.

THIS FUNCTION UPLOAD THE EVENT LOG INFORMATION FROM THE SELECTED NE AND
DISPLAY THE INFORMATION IN EVENT LOG WINDOW

FREQUENCY SETTING
TX POWER CONT
BIT RATE
EQUIPMENT SETUP

SYSTEM CONFIG

MAINTENANCE

LAN SETTING
FRAME ID
BER THRESHOLD
AIS SEND ON/OFF

MAINT MODE ON/OFF

AIS RCVD ON/OFF

TX MUTE ON/OFF

SC4 & SC5 SETTING

CW ON/OFF

NE NAME

BER AIS ON/OFF

NOTE

SWITCHOVER (1+1)

PNMT

10

PNMT LOGIN / LOGOUT & EXIT

NECITR-YTC
ART-SEP/03 V02

CLICK ON SYSTEM IN THE MENU BAR AND THEN CLICK ON LOGIN/LOGOUT IN THE DROP DOWN MENU TO OPEN
THE LOGIN/LOGOUT WINDOW

TO LOGIN SELECT LOGIN IN THE

LOGIN/LOGOUT WINDOW.
ENTER THE USER NAME ACCORDING TO THE
PRIVILEGES AND THE PASSWORD.
CLICK OK TO LOGIN
TO PROTECT THE NETWORK AND NETWORK
MANAGEMENT SYSTEM FROM UNAUTHORIZED
ACCESS OR MODIFICATIONS, FIVE LEVELS OF
USERS ARE DEFINED WITH DIFFERENT
PRIVILEGES. THE FUNCTIONS AVAILABLE
DEPENDS ON THE USER ACCESS LEVEL, (SEE
THE TABLE NEXT PAGE)

TO LOGOUT SELECT LOGOUT IN THE

LOGIN/LOGOUT WINDOW AND CLICK OK.

PNMT

11

USER NAMES & PRIVILEGES

Category
MENU-SYSTEM

Item

Monitor(0)

User(1)

Local(2)

Remote(3)

Admin(4)

DATE TIME
ALARM BUZZER

NECITR-YTC
ART-SEP/03 V02

DOWNLOAD PMC PROGRAM FILE

CONNECT (REMOTE LOGIN)

MENU-CONFIGURATION FILE

UPDATE
IDU

MAINTENANCE

WS ALARM INHIBIT (OPTION)

CH (LB1) / CH(LB2)
CH (ALARM INHIBIT)

MAINTENANCE MODE

TX MUTE

CW

SWITCH OVER (1+1)

FREQUENCY PLAN (CH)

TX ATTENUATION

BER AIS
EQUIPMENT CONFIGURATION

DOWNLOAD FILE/ UPLOAD FILE

BIT RATE

BER THRESHOLD

AIS RCVD ALARM ON/OFF

AIS SEND ALARM ON/OFF

SC4 AND SC5

FRAME ID

NOTE

OPTO ITEM TYPE

OPTO NAME

RELAY NAME

RELAY CONTROL

PMON THRESHOLD

SAVE TO DISK

LOGGING

SAVE TO DISK

PMC

RESET

PASOLINK NAME
AUX I/O

PMON

PMON DATA RESET

PNMT

12

OVERALL WINDOW

NECITR-YTC
ART-SEP/03 V02

OVERALL WINDOW FOR (1+1) CONFIGURATION

OVERALL WINDOW FOR (1+0) CONFIGURATION

OVERALL WINDOW DISPLAY THE FOLLOWING INFORMATION:

TX ATTENUATION USED
TX AND RX FREQUENCIES USED
BIT RATE USED
MAINTENANCE MODE ON OR OFF STATUS. IF ON, BACK GROUND COLOR
CHANGE TO YELLOW.
SELECTED TX AND RX CHANNEL IN (1+1) HOT STANDBY CONFIGURATION
FRAME ID USED
ODU TYPE USED V3 OR V4
CLICK THE OVERALL TAB TO DISPLAY THE OVERALL
WINDOW

TX POWER CONTROL USED

PNMT

13

ODU WINDOW

NECITR-YTC
ART-SEP/03 V02

CLICK THE ODU SYMBOL IN THE BLOCK DIAGRAM TO OPEN THE ODU
WINDOW TO VIEW THE ODU DETAILS
ODU WINDOW FOR (1+1) CONFIGURATION

ODU WINDOW FOR (1+0) CONFIGURATION

CLICK THE ODU TAB TO OPEN THE ODU WINDOW TO VIEW THE ODU DETAILS

PNMT

14

ODU DETAIL

NECITR-YTC
ART-SEP/03 V02

TX SIDE ALARMS AND STATUS /MONITORING

ALARMS
IF INPUT IF INPUT LEVEL IN THE ODU FALLS BELOW (APPROXIMATELY) -63 dB
TX APC ODU TX SIDE SYNTHESIZER IS UNLOCKED
TX POWER TRANSMIT POWER DECREASED BY 3 TO 5 dB
STATUS AND MONITORING
TX ATTENUATION INDICATES THE ATTENUATION VALUE USED IN MTPC MODE
TX POWER INDICATES THE ODU TRANSMIT POWER AS DETECTOR VOLTAGE AND IN dBm
(1+1) CONFIGURATION SELECTED/NOT SELECTED STATUS
GREEN
SELECTED
WHITE
NOT SELECTED
RX SIDE ALARMS AND STATUS /MONITORING
ALARMS
RX LEVEL ODU RECEIVE LEVEL FALLS BELOW SQUELCH LEVEL

RX APC ODU RX SIDE SYNTHESIZER IS UNLOCKED

STATUS AND MONITORING
RX LEVEL INDICATES THE ODU RX LEVEL AS THE AGC VOLTAGE AND IN dBm
COMMON ALARMS AND STATUS /MONITORING
ALARMS
ODU-IDU LINK INDICATES THE STATUS OF THE COMMUNICATION BETWEEN IDU AND ODU
STATUS AND MONITORING
ODU TYPE INDICATES THE TYPE OF ODU CONNECTED TO THE V4 PASOLINK

STATUS COLORS
GREEN
NORMAL
RED
ALARM

PNMT

15

IDU WINDOW

NECITR-YTC
ART-SEP/03 V02

CLICK THE IDU SYMBOL IN THE BLOCK DIAGRAM TO OPEN THE IDU WINDOW TO VIEW THE IDU DETAILS

IDU WINDOW FOR (1+0) CONFIGURATION

IDU WINDOW FOR (1+1) CONFIGURATION

CLICK THE IDU TAB TO OPEN THE IDU WINDOW TO VIEW THE IDU DETAILS

PNMT

16

IDU DETAIL

NECITR-YTC
ART-SEP/03 V02

TX SIDE IDU ALARMS

MOD MODULATOR 850 MHz PLL OSCILLATOR UNLOCK ALARM
TX DPU LOSS OF TX SIDE CLOCK
(1+1) CONFIGURATION ON LINE SELECTED/NOT SELECTED STATUS
GREEN
SELECTED
WHITE
NOT SELECTED

STATUS COLORS
GREEN
NORMAL
RED
ALARM
PINK
MINOR ALARM

RX SIDE IDU ALARMS

DEM RX CARRIER NOT SYNCHRONIZED OR LOST
LOW BER WHEN THE RECEIVE BER IS > 10-6
HIGH BER WHEN THE RECEIVE BER IS >10-3
BER ALARM ALARM TRIGGER POINT SELECTABLE (10-3,10-4,10-5 AND 10-6)
FRAME ASYNC LOSS OF RX FRAME SYNCHRONIZATION AT THE RX DPU
RX CLK LOSS LOSS OF RX SIDE CLOCK
IDU COMMON ALARMS
ODU-IDU LINK STATUS OF THE ODU-IDU IF LINK
CPU STATUS OF THE IDU CPU
WAY SIDE( OPTION) ALARMS
INPUT LOSS OF WS INPUT SIGNAL IN THE WS INTFC CARD
BP OUTPUT RX WS SIGNAL LOSS FROM DEMODULATOR (WS INTFC CARD)
AIS SEND STATUS AIS SENT OUT FORM THE WS INTFC CARD
AIS RECEIVED AIS DETECTED IN WS INPUT SIGNAL
ALARM INHIBIT WHEN WS SIGNAL IS NOT USED ALARM INHIBIT STATUS
Normal
Port 1
Normal
Normal

LAN INTFC (OPTION) ALARMS

Port 2
Normal
Normal

LAN INTFC LAN INTERFACE OPTION CARD IS NORMAL OR FAULTY

LAN LINK LAN PORT 1 & 2 LINK STATUS NORMAL OR ALARM
LAN COLLISION COLLISION STATUS OF THE LAN PORT 1 & 2

PNMT

17

IDU DETAIL

NECITR-YTC
ART-SEP/03 V02

CLICK THE CH BUTTON TO OPEN THE CHANNEL

CONTROL WINDOW
LOOPBACK 1 CONTROL
LOOPBACK 2 CONTROL
CH ALARM INHIBIT CONTROL
STATUS COLORS
GREEN
NORMAL
RED
ALARM
YELLOW
MAINTENANCE
BP OUTPUT

RX 2MB SIGNAL LOSS

DETECTED FROM DEMODULATOR

2MB CH STATUS AND ALARMS

INPUT
LOSS OF 2MB INPUT SIGNAL

NORMAL/ALARM/INHIBIT
NORMAL/ALARM
NORMAL/SEND
NORMAL/RECEIVED
ON/OFF
ON/OFF
ON/OFF

BP OUTPUT

RX 2MB SIGNAL LOSS DETECTED FROM DEMODULATOR

AIS SEND

AIS SENT OUT STATUS FORM THE 2MB INTFC CARD

WS

AIS RECEIVED

AIS DETECTED STATUS IN 2MB INPUT SIGNAL

LB-1

UNDER MAINTENANCE MODE NEAR END LOOPBACK STATUS

LB-2

UNDER MAINTENANCE MODE, TO FAR END LOOPBACK STATUS

ALARM INHIBIT

ALARM INHIBIT STATUS OF NOT USED 2MB STREAMS

ALARM INHIBIT
OFF

WS CH STATUS AND ALARMS

INPUT
LOSS OF 2MB WS INPUT SIGNAL
BP OUTPUT
RX 2MB WS SIGNAL LOSS DETECTED FROM DEMODULATOR
AIS SEND
AIS SENT OUT STATUS FORM THE WS INTFC CARD
AIS RECEIVED
AIS DETECTED STATUS IN WS INPUT SIGNAL
ALARM INHIBIT
ALARM INHIBIT STATUS OF NOT USED 2MB STREAMS

PNMT

18

CHANNEL CONTROL

NECITR-YTC
ART-SEP/03 V02

INDICATE LOOPBACK ON, YELLOW BACKGROUND

INDICATE MAINTENANCE MODE

IN THE IDU WINDOW CLICK ON

THE CH # TO BE CONTROLLED.
SELECTED CHANNEL CONTROL
WINDOW OPENS

INDICATE CHANNEL ALARMS INHIBIT ON

INDICATE CHANNEL ALARMS INHIBIT ON

LB1 TAB PROVIDES NEAR END LOOPBACK.

SELECT ON OR OFF AND CLICK ON
EXECUTE
TO
ENABLE
NEAR
END
LOOPBACK ON THE SELECTED CHANNEL.
BEFORE ENABLING LOOPBACK SELECT
MAINTENANCE MODE ON. OTHERWISE AN
ERROR MESSAGE. IS DISPLAYED

LB2 TAB PROVIDES

FAR END
LOOPBACK. SELECT ON OR OFF AND
CLICK ON EXECUTE TO ENABLE FAR
END LOOPBACK ON THE SELECTED
CHANNEL..

ALARM TAB PROVIDES INHIBIT OF ALARM

ON THE SELECTED CHANNEL. USED TO
INHIBIT ALARMS FROM THE UNUSED 2 MB
CHANNELS.
ON INHIBIT ALARMS

OFF - ENABLE ALARMS

CLICK EXECUTE TO SELECT THE CHANGE

PNMT

19

CHANGE PASSWORD

NECITR-YTC
ART-SEP/03 V02

CLICK ON CHANGE PASSWORD IN THE SYSTEM

DROPDOWN MENU TO OPEN THE CHANGE PASS WORD
WINDOW.

ENTER THE OLD PASSWORD

ENTER THE NEW PASSWORD

RE-ENTER THE NEW PASSWORD TO CONFIRM

CLICK OK TO CHANGE THE

PASSWORD.
CLICK CANCEL TO EXIT WITHOUT
CHANGING PASSWORD

PNMT

20

ALARM BUZZER
CLICK ON ALARM BUZZER ON
THE SYSTEM DROP DOWN
MENU TO OPEN THE ALARM
BUZZER SETTING WINDOW.

NECITR-YTC
ART-SEP/03 V02

SELECT NO SOUND TO DISABLE THE BUZZER

SELECT WAVE FILE TO ENABLE THE BUZZER. THE BUZZER

SOUND CAN BE CHANGED BY SELECTING A DIFFERENT
WAV FILE. USE BROWSE
TO LOCATE THE PATH TO
THE WAV FILE.
CLICK HERE TO TEST THE BUZZER SOUND

CLICK OK TO IMPLEMENT THE

OPTION SELECTED OR CLICK
CANCEL TO EXIT WITHOUT
CHANGING THE SETTINGS.

SELECT BEEP TO ENABLE THE

BUZZER WITH BEEP FREQUENCIES
INSTEAD OF WAVE FILE SOUND
BEEP FREQUENCY CAN BE DEFINED BY CLICKING ON EDIT AND SELECTING THE FREQUENCIES
AND DURATION FOR EACH FREQUENCY. CLICK THE ARROW KEY TO ADD TO THE LIST. SEVERAL
FREQUENCIES CAN BE ADDED TO THE BEEP SIGNAL. SELECTED FREQUENCIES CAN BE DELETED
BY SELECTING THE FREQUENCY FROM THE LIST AND CLICKING ON THE DELETE SYMBOL.

PNMT

21

SEARCH / CONNECT TO NETWORK ELEMENT

NECITR-YTC
ART-SEP/03 V02

CLICK CONNECT ON THE SYSTEM DROP DOWN MENU TO LIST THE LOCAL NEs THE PNMT IS CONNECTED TO.

LIST MENU

CLICK THE SEARCH FOR NETWORK ELEMENT TO

SEARCH AND LIST THE OTHER NEs IN THE
NETWORK

TO VIEW A REMOTE NE FROM THE NETWORK ELEMENT LIST, SELECT AND

HIGHLIGHT THE NE IN THE LIST. THEN CLICK THE CONNECT TO NETWORK
ELEMENT FROM THE LIST DROP DOWN MENU. SELECT YES FROM THE
DIALOG BOX. THE SELECTED NE AND ITS OPPOSITE NE WILL BE
DISPLAYED IN THE LINK SUMMARY WINDOW.
TOOL BAR ITEMS

CONNECT TO NETWORK ELEMENT

SEARCH FOR NETWORK ELEMENT

PNMT

22

HELP FUNCTION

NECITR-YTC
ART-SEP/03 V02

PNMT HELP FUNCTION IS AVAILABLE AS PNMT MANUAL IN

PDF FILE FORMAT. IF THE ACROBAT READER IS
INSTALLED IN THE PNMT PC, CLICKING HELP AND
SELECTING THE RELEVANT PNMT FILE WILL OPEN THE
PDF FILE TO PROVIDE HELP FUNCTION TO THE USER.

BUZZER STOP ICON IS ACTIVE ONLY WHEN

THE, THE ALARMED EQUIPMENT DISPLAY
WINDOW IS SELECTED FROM THE TABs OR
FROM THE BLOCK DIAGRAM SYMBOLS.

DISPLAY THE PNMT SOFTWARE VERSION INFORMATION

REFRESH REFRESH METERING ITEMS

CONNECT - OPEN THE NE LIST WINDOW

OPEN THE LOGIN/LOGOUT WINDOW

PNMT

23

EQUIPMENT CONFIGURATION WINDOW

NECITR-YTC
ART-SEP/03 V02

INDICATES THE ODU

FREQUENCY BAND
INFORMATION AND TX/RX
FREQUENCIES
INDICATES THE TX
POWER CONTROL MODE
AND TX ATT
SHOW THE TYPE AND NUMBER
OF OPTIONAL INTERFACE
CARDS MOUNTED

SHOW THE CURRENT IDU

CONFIGURATION

SHOW THE LAN SIGNAL

STATUS FOR PORT1 AND
PORT2, WHEN MAIN LAN
INTFC OPTION IS USED

SHOW THE WS
CHANNEL
INFORMATION
SHOW THE
SERVICE CHANNEL
INFORMATION

SHOW IP ADDRESS AND NAME OF

THE SELECTED NE

PNMT

24

FREQUENCY AND POWER SETTING

NECITR-YTC
ART-SEP/03 V02

ODU SECTION OF THE EQUIPMENT SETUP WINDOW FOR THE SELECTED PASOLINK HAS THREE
CONTROLS, FREQUENCY PLAN , TX ATTENUATION AND TX POWER CONTROL SETTING.
IN THE CASE OF (1+1) HOT STANDBY CONFIGURATION, FREQUENCY IS SET FOR BOTH ODUs.
CLICK ON THE FREQUENCY PLAN BUTTON TO SELECT
THE ODU TX AND RX FREQUENCIES.
INFORMATION ABOUT THE ODU FREQUENCY BAND ARE
DISPLAYED

This information may include :

TX frequency used is High band or Low band
Frequency Sub band used A, B, C, or D.
Default Channel and TX frequency set in the ODU.
CH Separation
shift frequency
CLICK ON THE TX ATTENUATION
BUTTON TO SET THE TX ATTENUATION
FOR MTPC.

REFER TO THE RADIO FREQUENCY ASSIGNMENT TABLES TO

SELECT THE CHANNEL NUMBER CORRESPONDING TO THE
REQUIRED TRANSMIT AND RECEIVE FREQUENCIES.

SELECT THE CHANNEL NUMBER AND THE CORRESPONDING TX

AND RX FREQUENCIES FOR THE SELECTED CHANNEL. ARE
DISPLAYED
CLICK THE EXECUTE BUTTON TO CHANGE THE FREQUENCIES.
THIS OPERATION WILL INTERRUPT THE TRAFFIC
CLICK THE CLOSE BUTTON TO EXIT THE FREQUENCY PLAN
WINDOW.
SELECT THE AMOUNT OF ATTENUATION
REQUIRED AND CLICK THE EXECUTE BUTTON.
THE TX ATTENUATION RANGE OF ODU IS 0 TO
30 dB
CLICK CLOSE TO EXIT THE TX ATTENUATION
SETTING WINDOW.

PNMT

25

ATPC SETTING

NECITR-YTC
ART-SEP/03 V02

TX POWER CONTROL
WHEN TC CONTROL MODE IS ATPC, TX
ATTENUATION SETTING VALUE IS IGNORED

SELECTS THE TX POWER CONTROL MODE

ATPC OR MTPC. WHEN ATPC IS SELECTED,
ATPC RX THRESHOLD , ATPC MAX POWER
AND ATPC MIN POWER BUTTONS ARE ACTIVE.

WHEN TX CONTROL MODE IS CHANGED

FROM ATPC TO MTPC, THE TX ATTENUATION
SETTING IS AUTOMATICALLY SET TO THE
ATPC MAX POWER SETTING VALUE.

RX THRESHOLD LEVEL
WHEN THE MONITORED RX SIGNAL LEVEL
FALLS BELOW THIS LEVEL, CONTROL SIGNAL
SENT TO THE OPPOSITE STATION INITIATE THE
ATPC FUNCTION.
THIS IS EFFECTIVE ONLY WHEN THE OPPOSITE
STATION IS SET TO ATPC MODE
CLICK THE APPROPRIATE BUTTON TO
OPEN THE SELECTED SETTING WINDOW..

AUTOMATIC TX POWER MAX AND MIN RANGE

ATPC RANGE DEFINES THE MAXIMUM AND MINIMUM TRANSMISSION POWER
DURING ATPC OPERATION. IN MTPC MODE THIS MENU ITEM DOES NOT APPEAR.

VALUE SET IS THE ATTENUATION IN dB FROM MAX ODU POWER.

IF THE MAXIMUM OUTPUT POWER OF THE ODU IS +20 DBM, THEN FOR AN ATPC MAX
PWR SETTING OF 0DB AND ATPC MIN PWR SETTING OF -10DB, THE ODU OUTPUT
POWER DURING ATPC OPERATION CAN VARY BETWEEN +20 DBM AND +10 DBM

PNMT

AFTER SELECTING OR SETTING THE

PARAMETER CLICK EXECUTE BUTTON TO
IMPLEMENT THE SETTING.

IN ALL SETTING WINDOWS, CLICK CLOSE

TO EXIT THE WINDOW

26

IDU SETTING
BIT RATE SETTING

NECITR-YTC
ART-SEP/03 V02
IDU SECTION OF THE EQUIPMENT SETUP WINDOW FOR
THE SELECTED PASOLINK HAS CONTROL SETTINGS FOR
THE MAIN SIGNAL.

CLICK BIT RATE BUTTON TO OPEN THE BIT RATE SETTING

WINDOW. THIS FUNCTION APPLIES TO THE VARIABLE BIT RATE
IDUs. SELECT THE BIT RATE AND CLICK THE EXECUTE BUTTON
TO CHANGE THE BIT RATE SETTING..

REDUNDANCY
CLICK REDUNDANCY BUTTON TO OPEN THE REDUNDANCY
CONFIGURATION SETTING WINDOW. SELECT THE REQUIRED
CONFIGURATION. CLICK ON THE EXECUTE BUTTON TO SET THE
REDUNDANCY CONFIGURATION.

BER THRESHOLD SETTING

CLICK BER THRESHOLD BUTTON TO OPEN THE BER
THRESHOLD SETTING WINDOW. SELECT THE DESIRED
VALUE FOR THE BER THRESHOLD. CLICK ON THE
EXECUTE BUTTON TO SET THE BER THRESHOLD VALUE.

FRAME ID
CLICK FRAME ID BUTTON TO OPEN THE
FRAME ID SETTING WINDOW.
SELECT THE FRAME ID AND CLICK ON
THE EXECUTE BUTTON TO SET IT.
MAKE SURE THAT BOTH NEs IN THE
HOP HAVE THE SAME FRAME ID VALUE.

AT THIS BER THRESHOLD VALUE AIS SIGNAL IS INSERTED

TO THE 2MB STREAMS

PNMT

27

AIS SEND / RCVD SETTING

NECITR-YTC
ART-SEP/03 V02

IN THE PASOLINK SYSTEM WHEN AIS IS DETECTED FROM THE INPUT 2MB STREAM AIS RCVD CONDITION IS DECLARED. THIS CONDITION
CAN BE DEFINED AS AN ALARM CONDITION OR STATUS CHANGE EVENT. SIMILARLY AIS IS SENT TO THE 2MB STREAM IN THE RECEIVE
DIRECTION UNDER CERTAIN CONDITIONS. AIS SEND CAN ALSO BE DEFINED AS AN ALARM CONDITION OR STATUS CHANGE EVENT.

CLICK AIS RCVD BUTTON TO OPEN THE

AIS RCVD SETTING WINDOW.

CLICK AIS SEND BUTTON TO OPEN THE

AIS SEND SETTING WINDOW.

SELECT AIS SEND CONDITION AS AN

ALARM CONDITION OR STATUS
CONDITION.

SELECT AIS RECEIVED CONDITION AS AN

ALARM CONDITION OR STATUS
CONDITION.

CLICK EXECUTE TO CARRY OUT THE

SETTING.

CLICK EXECUTE TO CARRY OUT THE

SETTING.

CLICK CLOSE TO EXIT

CLICK CLOSE TO EXIT

PNMT

28

SERVICE CHANNEL SETTING

NECITR-YTC
ART-SEP/03 V02

OPTION PANEL STATUS SHOWS THE OPTION CARDS

MOUNTED IN THE IDU.

OVERHEAD SERVICE CHANNELS

SERVICE CHANNELS USED IN THE PASOLINK IS SHOWN ON
THE TABLE. SC2 AND 3 NEEDS OPTIONAL ANALOG OR
DIGITAL SERVICE CHANNEL INTERFACE CARD.
SC4 AS A DEFAULT USE A 9.6K RS232 INTERFACE. IF THE
OPTIONAL 64K INTERFACE CARDS ARE MOUNTED. THEN THE
SC4 BUTTON IS ACTIVE TO SELECT EITHER 9.6 OR 64K.
INTERFACE
WHEN OPTIONAL 64K INTERFACE IS MOUNTED THIS BUTTON
IS ACTIVE.. CLICK ON SC4 BUTTON TO OPEN THE SC4
SETTING WINDOW.

SC1

EOW

Analog

SC2
SC3

DSC3
DSC4

Analog
Digital

ASC INTFC or
DSC INTFC

Option
Option

SC4

DSC1

Digital

9.6Kbps RS 232C or
64Kbps with G703/V11 card

Option

SC5

DSC2

Digital

9.6Kbps RS232C / RS422 / RS485

SC6

NMS

CLICK ON SC5 BUTTON TO OPEN THE SC5 SETTING WINDOW.

SC4
SC4
64K V.11

64K G703

9.6K RS-232

SELECT THE REQUIRED OPTION AND CLICK EXECUTE.

PNMT

CLICK CLOSE TO EXIT THE WINDOW

29

PMC CARD SETTING

FROM THE EQUIPMENT SETUP WINDOW CLICK THE NE
NAME BUTTON TO OPEN THE NE NAME SETTING
WINDOW.

NECITR-YTC
ART-SEP/03 V02

THE NAME ENTERED TO IDENTIFY THE NETWORK

ELEMENT CAN BE CHANGED FORM THIS WINDOW. A
MAXIMUM OF 32 CHARACTERS CAN BE USED.

ENTER THE NAME AND CLICK EXECUTE TO SHOW THE

NAME IN THE EQUIPMENT SETUP WINDOW.
CLICK THE NOTE BUTTON TO OPEN THE
NOTE WINDOW.

A NOTE DESCRIBING THE NETWORK ELEMENT CAN BE

ENTERED FROM THIS WINDOW. UP TO 80 CHARACTERS
CAN BE USED IN THIS FIELD

ENTER THE NOTE AND CLICK EXECUTE TO SHOW THE

NOTE IN THE EQUIPMENT SETUP WINDOW.

PNMT

30

MAINTENANCE
CLICK MAINTENANCE, ON THE,
CONFIGURATION DROP DOWN
MENU TO OPEN THE
MAINTENANCE WINDOW

NECITR-YTC
ART-SEP/03 V02

TO CARRY OUT ANY MAINTENANCE CONTROL ,SET THE SELECTED NE TO

MAINTENANCE MODE. CLICK THE MAINT BUTTON ON THE MAINTENANCE
WINDOW TO OPEN MAINTENANCE MODE SELECTION WINDOW. SELECT
MAINT MODE ON OR OFF AND CLICK EXECUTE TO IMPLEMENT THE MODE
SELECTION
THIS CONTROL TRANSMIT AN UNMODULATED CARRIER FOR
MEASUREMENT PURPOSE.
CLICK THE CW BUTTON ON THE
MAINTENANCE WINDOW TO OPEN THE
CW CONTROL WINDOW. CLICK ON/OFF
AND EXECUTE TO IMPLEMENT THE
CONTROL.
THIS CONTROL INHIBIT INSERTION OF
AIS DURING BER ALARM CONDITION
FOR MEASUREMENT PURPOSE.
CLICK THE BER AIS BUTTON ON THE
MAINTENANCE WINDOW TO OPEN THE
BER AIS CONTROL WINDOW. CLICK
ON/OFF AND EXECUTE TO IMPLEMENT
THE CONTROL.

THIS CONTROL MUTE THE OUTPUT

POWER OF THE SELECTED PASOLINK
CHANNEL .

THESE CONTROL ARE

AVAILABLE FOR (1+1)
CONFIGURATION.
PROVIDES MANUAL
SWITCH OVER OF
PASOLINK CHANNEL

CLICK THE TX MUTE BUTTON ON THE

MAINTENANCE WINDOW TO OPEN THE
TX MUTE CONTROL WINDOW. CLICK
ON/OFF AND EXECUTE TO IMPLEMENT
THE CONTROL.

FOR NORMAL OPERATION

SELECT AUTO FOR AUTO
REDUNDANCY
SWITCHING..

TO CLOSE ANY MAINTENANCE CONTROL WINDOW CLICK CLOSE BUTTON. TO

NORMALIZE MAINTENANCE MODE NORMALIZE MAINTENANCE CONTROLS FIRST.

PNMT

31

AUX I/O WINDOW - MONITORING

NECITR-YTC
ART-SEP/03 V02

AUXILIARY INPUT / OUTPUT FACILITY CAN BE USED TO MONITOR SIX EXTERNAL MONITOR ITEMS AND FOUR EXTERNAL CONTROL ITEMS USING THE
PASOLINK MANAGEMENT SYSTEM. MONITORING ITEMS ARE CONNECTED THROUGH OPTICAL COUPLERS AND CONTROLS VIA RELAYS. THESE ITEMS
ARE ALSO KNOWN AS HOUSEKEEPING ALARMS AND CONTROLS.
CLICK THE AUX SYMBOL IN THE BLOCK DIAGRAM OR AUX I/O TAB TO
VIEW THE AUX ALARM/STATUS/CONTROL DISPLAY

CONFIGURE CONTROL RELAY OUTPUTS

CLICK THE OUTPUT 1-4 BUTTONS TO CONFIGURE
THE EXTERNAL CONTROLS
ENTER THE NAME TO
APPEAR FOR
SELECTED CONTROL
ITEM ( UP TO 32
CHARACTERS)

ENTER THE LABEL FOR

EACH CONDITION
EVENT ON AND EVENT
OFF
CLICK EXECUTE TO CARRY OUT THE CHANGE

ENTER THE SELECTED EXTERNAL ALARM NAME,

(UP TO 32 CHARACTERS)

CONFIGURE ALARM INPUTS

CLICK THE INPUT 1-6
BUTTONS TO CONFIGURE
THE EXTERNAL ALARM
SELECT THE CONDITION FOR
ALARM, EVENT ON OR EVENT
OFF

EXTERNAL MONITORING ITEMS

CAN BE DEFINED AS ALARMS OR
AS STATUS CHANGE.

ENTER THE LABEL FOR ALARM/ STATUS EVENT ON AND

EVENT OFF.

CLICK EXECUTE TO CARRY

OUT THE CHANGE

CLICK THE CLOSE BUTTON TO CLOSE THE WINDOW

PNMT

32

PMC & VERSION WINDOWS

CLICK THE PMC SYMBOL ON THE BLOCK DIAGRAM OR
THE PMC TAB TO DISPLAY THE PMC WINDOW FOR THE
SELECTED NE.

NECITR-YTC
ART-SEP/03 V02

CLICK THE VERSION TAB TO DISPLAY THE VERSION

INFORMATION WINDOW FOR THE SELECTED NE.

VERSION WINDOW DISPLAY THE DATE OF MANUFACTURE ,

SOFTWARE VERSIONS, SERIAL NUMBER, CODE NUMBER
ETC.. OF THE PASOLINK EQUIPMENT IN THE SELECTED
NETWORK ELEMENT.

CONFIGURATION AND SETTING OF THE PASOLINK

MANAGEMENT CARD IS PROVIDED IN THIS WINDOW.

PNMT

33

DATE TIME SETTING

NECITR-YTC
ART-SEP/03 V02

DATE AND TIME STORED IN THE SELECTED NETWORK ELEMENTS PM CARD CAN BE DISPLAYED AND ADJUSTED FORM THIS CONTROL ITEM
[PMC WINDOW]
TO DISPLAY THE CURRENT DATE/TIME
STORED IN THE PM CARD, SELECT
GET DATE/TIME AND CLICK EXECUTE.
CLICK DATE/TIME
BUTTON IN THE PMC
WINDOW TO OPEN THE
DATE/TIME SETTING
CONTROL WINDOW

TO CHANGE THE PM CARD DATE TIME SETTING,

SELECT SET DATE/TIME.
TO DISPLAY AND SET THE DATE/TIME SET IN THE
PNMT PC TO THE PM CARD, SELECT DISPLAY PC
TIME BOX AND CLICK THE EXECUTE BUTTON.

THE CURRENT DATE/TIME STORED IN

THE PM CARD, IS DISPLAYED.

TO CHANGE THE PM CARD DATE TIME SETTING,

SELECT SET DATE/TIME.
CHANGE THE DATE /TIME SETTING AS REQUIRED,
CLICK THE EXECUTE BUTTON.

PNMT

34

DOWN LOAD CONFIGURATION FILES

NECITR-YTC
ART-SEP/03 V02

THIS FUNCTION IS USED TO DOWN LOAD CONFIGURATION FILES CREATED BY THE

NETWORK CONFIG TOOL TO THE PM CARD IN THE SELECTED NETWORK ELEMENT.
THERE ARE TWO FILES CREATED FOR EACH NE, SYSTEM.CFG CONTAINS THE IP
ADDRESS OF THE PM CARD AS WELL AS THE IP ADDRESS OF THE OPPOSITE STATION.
THE NETWORK.CFG FILE CONTAINS THE INFORMATION ABOUT THE PASOLINK
NETWORK WHERE THE PM CARD IS LOCATED.
CLICK THE CONFIGURATION FILE BUTTON UNDER THE
DOWNLOAD (PC>>PMC) IN THE PMC WINDOW, TO OPEN THE
DOWNLOAD CONFIGURATION FILE WINDOW.
[PMC WINDOW]

DOWN LOAD
SELECT EACH CONFIG FILE ONE BY ONE FROM
THE TYPE WINDOW
BROWSE AND SELECT THE PATH/LOCATION TO
THE FILE SELECTED IN THE TYPE WINDOW.
CLICK EXECUTE BUTTON TO DOWN LOAD THE
SELECTED CONFIG FILE..
REPEAT THE DOWNLOAD PROCEDURE FOR THE
OTHER CONFIG FILE..

UPDATE
AFTER THE SUCCESSFUL DOWN LOAD OF
THE CONFIGURATION FILES. CLICK
UPDATE BUTTON. UPDATE
CONFIGURATION FILE WINDOW OPENS.
SELECT THE APPROPRIATE BOX FOR THE
TYPE OF CONFIGURATION FILE(S) THAT
WILL BE UPDATED.
CLICK OK BUTTON TO START THE UPDATE
OPERATION..
WHEN UPDATING SYSTEM.CFG FILE , PMC TO
PMC COMMUNICATION WILL BE LOST WHEN PM
CARD INITIALIZES TO THE NEW SYSTEM
CONFIGURATION. DURING THIS TIME PNMT
CONNECTION TO THE PASOLINK WILL BE LOST
BUT WILL AUTOMATICALLY BE RECONNECTED
AFTER THE PMC RESETS

A MESSAGE WINDOW INDICATE THE STATUS OF

THE DOWNLOAD OPERATION AND IT WILL CLOSE
AUTOMATICALLY ONCE THE OPERATION IS OVER
System Config
WARNING
MAKE SURE THAT THE CORRECT CONFIGURATION FILE IS DOWN
LOADED TO THE PM CARD IN THE CORRECT NE. INCORRECT
CONFIGURATION FILE WILL LEAD TO PM CARD OR NETWORK
FAILURE

Network Config
ME Config
PPP Config
With ROM (PMC Program ) Switching
Execute

MAKE SURE THAT YOU HAVE SUCCESSFULLY DOWN LOADED

THE CONFIGURATION FILE BEFORE DOING UPDATE. OTHERWISE
THE PM CARD WILL SWITCH TO AN EMPTY ROM THAT MAY CAUSE
PM CARD FAILURE.

CLICK CLOSE BUTTON WHEN DONE

PNMT

35

DOWN LOAD PROGRAM FILE

NECITR-YTC
ART-SEP/03 V02

THIS FUNCTION IS USED TO UPDATE THE APPLICATION PROGRAM ON THE PM

CARD. THIS OPERATION AFFECTS THE ONLY THE PMC TO PMC COMMUNICATION.
AND WILL NOT DISRUPT THE RADIO LINK.

CLICK ON THE PROGRAM FILE BUTTON UNDER THE DOWNLOAD (PC>>PMC) IN THE
PMC WINDOW.

[PMC WINDOW]
A:\pm.pof
PM CARD CAN BE RESET
USING THIS FUNCTION
CLICK THE PMC RESET
BUTTON ON THE PMC
WINDOW.

ENTER THE PATH TO THE

PROGRAM FILE TO BE
DOWNLOADED OR CLICK BROWSE
TO LOCATE THE PROGRAM FILE.
CLICK THE EXECUTE BUTTON TO
START DOWNLOAD OPERATION
A MESSAGE WINDOW APPEARS
TO SHOW THE STATUS OF THE
DOWNLOAD OPERATION, AND
WILL CLOSE AUTOMATICALLY
ONCE THE DOWNLOAD IS
COMPLETED.

CLICK ON THE PMC RESET

BUTTON TO SWITCH TO THE NEW
PROGRAM FILE

SELECT WITH ROM (PMC PROGRAM)

SWITCHING OPTION IF YOU WANT TO SWITCH
TO A NEWLY DOWNLOADED PMC PROGRAM
FILE
CLICK EXECUTE BUTTON TO RESET THE PM
CARD.

WARNING
MAKE SURE THAT THE CORRECT
PROGRAM FILE IS DOWNLOADED
TO THE PM CARD. INCORRECT
PROGRAM FILE WILL LEAD TO PM
CARD FAILURE.

RESETTING THE PMC WILL NOT AFFECT THE

TRAFFIC. THE CONNECTION TO THE
SELECTED PASOLINK WILL BE LOST FOR FEW
MINUTES AND WILL BE RECONNECTED
AUTOMATICALLY.

PNMT

36

UPLOAD CONFIGURATION FILE

NECITR-YTC
ART-SEP/03 V02

THIS FUNCTION IS USED TO UPLOAD THE CONFIGURATION FILES FROM

THE PM CARD OF THE SELECTED NE TO THE PNMT PC.

[PMC WINDOW]

CLICK THE CONFIGURATION FILE UNDER THE UPLOAD (PM>>PC) TO OPEN

THE UPLOAD CONFIGURATION FILE WINDOW.

SELECT THE TYPE OF CONFIG FILE TO BE UPLOADED FROM THE TYPE

WINDOW., SYSTEM CONFIG OR NETWORK CONFIG.

ENTER THE LOCATION THE FILE TO BE UPLOADED AND THE FILE NAME IN
THE FILE WINDOW. USE BROWSE TO LOCATE THE DIRECTORY IF
NECESSARY.
CLICK EXECUTE BUTTON TO START THE UPLOAD OPERATION. A MESSAGE
WINDOW APPEARS TO SHOW THE STATUS OF THE UPLOAD OPERATION,
AND WILL CLOSE AUTOMATICALLY ONCE THE OPERATION IS COMPLETED..
AFTER THE UP LOAD IS FINISHED CLICK THE CLOSE BUTTON TO CLOSE
THE WINDOW.

PNMT

37

EVENT LOG

NECITR-YTC
ART-SEP/03 V02

NE SPECIFIC MENU BAR

A MESSAGE WINDOW
SHOWS THE PROGRESS OF
THE UPLOAD

CLICK ON THE EVEN LOG IN

THE NE SPECIFIC MENU BAR
TO UPLOAD THE EVEN LOG
ITEMS FROM THE SELECTED
NE.
EVENT LOG VIEW WINDOW SHOWS
ALARM EVENTS, COMMAND EVENTS
AND STATUS CHANGES.
DIFFERENT COLORS SHOWS THE
TYPE OF EVENT.
EVENT LOG IS PRESENTED IN A TABLE
FORM SHOWING THE DATE OF THE
EVENT , THE ITEM THAT TRIGGERED
THE EVENT AND THE STATUS
CHANGE.

CLICK FILE-UPLOAD TO REFRESH THE EVENT

LOG DISPLAY
CLICK FILE-SAVE AS TO SAVE THE EVENT
LOG TO
CLICK FILE-PRINT TO PRINT THE EVENT
LOG INFORMATION

PNMT

38

LINK PERFORMANCE MONITOR

NECITR-YTC
ART-SEP/03 V02

NE SPECIFIC MENU BAR

THE FOLLOWING PERFORMANCE ITEMS CAN BE MONITORED
ACCORDING TO THE G.826 RECOMMENDATIONS.

CLICK ON THE LINK PERFORMANCE MONITOR IN THE NE

SPECIFIC MENU BAR OF THE LINK SUMMARY WINDOW OF
THE PASOLINK TO BE MONITORED.

ES
SES
UAS
BBE

ERROR SECONDS
SEVERELY ERROR SECONDS
UNAVAILABLE SECONDS
BACKGROUND BLOCK ERRORS

CURRENT BER VALUE IS SHOWN IN THIS FIELD

THE RED COLOR IN THE PERFORMANCE MONITOR WINDOW
INDICATES THE OCCURRENCE
OF PERFORMANCE ITEMS
EXCEEDING THE THRESHOLD VALUE. THE THRESHOLD VALUES
CAN BE SET IN THRESHOLD WINDOW. ALL DATA CAN BE RESET BY
USING ALL DATA RESET BUTTON. ( MAKE SURE THAT THE
CURRENT DATA HAS BEEN SAVED AS THIS OPERATION WILL
DELETE ALL THE PERFORMANCE DATA IN THE CURRENT WEEK.)

THRESHOLD VALUE SETTING

CLICK THE THRESHOLD(%) BUTTON TO OPEN THE THRESHOLD SETTING
WINDOW.
SELECT THE PERFORMANCE ITEM THAT IS TO BE CONFIGURED ON THE
TABLE SHOWN. SET THE VALUE WHEN THE ALARM OCCUR AND WHEN
THE ALARM RECOVER IN THE APPROPRIATE FIELD.
AFTER SETTING ALL THE THRESHOLD VALUES CLICK EXECUTE TO
ACTIVATE THE NEW SETTING.

CLOCK CLOSE TO CLOSE THE THRESHOLD SETTING WINDOW..

PNMT

39

LINK PERFORMANCE MONITOR

CLICK ON THE DETAIL BUTTON IN THE LINK PERFORMANCE
MONITOR WINDOW TO DISPLAY THE WEEKLY DETAIL
WINDOW.

NECITR-YTC
ART-SEP/03 V02

THIS WINDOW CONTAINS THE LINK PERFORMANCE DATA OF

THE LAST .8 DAYS.

CLICK ON A DATE BUTTON TO DISPLAY THE DAILY DATA

WINDOW FOR THE SELECTED DATE

THE DATE BUTTONS ON THE RIGHT HAND SIDE OF THE

TABLE ARE SELECTABLE. AND CAN OPEN THE SUMMARY
DATA FOR THAT SPECIFIC DATE..

THE LINK PERFORMANCE MONITOR DAILY DATA WINDOW DISPLAY THE

DETAILED 15MIN PERFORMANCE DATA
CLICK FILE SAVE AS TO SAVE THE DATA IN TEXT FORMAT
CLICK FILE - UPLOAD TO REFRESH THE DATA

PNMT

40

NECITR-YTC
ART-SEP/03 V02

PASOLINK V4 SOFTWARE

NEC International Training, Ltd.

Yokohama Training Center
PNMT

41