http://www.tyco-fireproducts.

com

Series EC-11 & EC-14 11.2 and 14.0 K-factor Extended

Coverage (Light and Ordinary Hazard) Upright, Pendent,
and Rec.Pendent Sprinklers
General
Description
The Series EC-11 and EC-14 Extended Coverage Upright and Pendent Sprinklers are
decorative glass bulb sprinklers designed
for use in light or ordinary hazard occupancies. They are intended for use in automatic
sprinkler systems designed in accordance
with standard installation rules (e.g., NFPA
13) for a maximum coverage area of 400 ft2
(37,2 m2), as compared to the maximum
coverage area of 130 ft2 (12,1 m2) for standard coverage sprinklers used in ordinary
hazard occupancies or 225 ft2 (20,6 m2) for
standard coverage sprinklers used in light
hazard occupancies.
The Series EC-11 and EC-14 Sprinklers feature a UL and C-UL Listing that permits their
use with unobstructed or non-combustible
obstructed ceiling construction as defined
and permitted by NFPA 13, as well as a specific application listing for use under concrete tees.
The Series EC-11 and EC-14 Extended Coverage Sprinklers have been fire tested to
compare their performance to that of standard coverage spray sprinklers. These tests
have shown that the protection provided
is equal to or more effective than standard
coverage spray sprinklers.

Corrosion resistant coatings, where applicable, are utilized to extend the life of
copper alloy sprinklers beyond that which
would otherwise be obtained when exposed to corrosive atmospheres. Although
corrosion resistant coated sprinklers have
passed the standard corrosion tests of the
applicable approval agencies, the testing is
not representative of all possible corrosive
atmospheres. Consequently, it is recommended that the end user be consulted
with respect to the suitability of these corrosion resistant coatings for any given corrosive environment. The effects of ambient
temperature, concentration of chemicals,
and gas/chemical velocity, should be considered, as a minimum, along with the corrosive nature of the chemical to which the
sprinklers will be exposed.
WARNINGS
The Series EC-11 and EC-14 Extended Coverage Sprinklers described herein must be installed and maintained in compliance with
this document, as well as with the applicable
standards of the National Fire Protection Association, in addition to the standards of any
other authorities having jurisdiction. Failure
to do so may impair the performance of
these devices.
The owner is responsible for maintaining their
fire protection system and devices in proper
operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions.

IMPORTANT
Always refer to Technical Data Sheet
TFP700 for the INSTALLER WARNING
that provides cautions with respect to
handling and installation of sprinkler
systems and components. Improper handling and installation can permanently
damage a sprinkler system or its components and cause the sprinkler to fail to
operate in a fire situation or cause it to
operate prematurely.

Page1 of 8 February, 2007

Model/Sprinkler
Identification
Number
TY5137 - Upright, 11.2K
TY5237 - Pendent, 11.2K
TY6137 - Upright, 14.0K
TY6237 - Pendent,14.0K
TY5137 is a redesignation
G1894, and S2510.
TY5237 is a redesignation
G1893, and S2511.
TY6137 is a redesignation
G1896, and S2610.
TY6237 is a redesignation
G1895, and S2611.

for C5137,
for C5237,
for C6137,
for C6237,

TFP220_EN

Page2 of 8

TFP220_EN

3/4 **
NPT

WRENCH
FLAT
1 - Frame
2 - Button
3 - Sealing Assembly
4 - Bulb
5 - Compression Screw
6 - Deflector*

ESCUTCHEON PLATE
SEATING SURFACE

1
2

2-7/16
(61,9mm)
UPRIGHT &
PENDENT

* Temperature rating is
indicated on deflector

3
4

** Pipe thread
connections per ISO
7/1 can be provided
on special request.

5
6*

NOMINAL MAKE-IN
1/2 (12,7 mm)
UPRIGHT

SECTION
CROSS

PENDENT

FIGURE 1
SERIES EC-11 AND EC-14 EXTENDED COVERAGE SPRINKLERS
11.2 K-FACTOR (TY5137) UPRIGHT AND (TY5237) PENDENT
14.0 K-FACTOR (TY6137) UPRIGHT AND (TY6237) PENDENT
SPRINKLER FINISH (See Note 5)
HAZARD

TYPE

LIGHT

UPRIGHT
K=11.2 (TY5137)
PENDENT
K=11.2 (TY5237)
K=14.0 (TY6237)

Refer to Table B for

UL and C-UL
Sensitivity Rating
and
Refer to Table C for
FM
Sensitivity Rating

ORDINARY
Refer to Table B for
UL and C-UL
Sensitivity Rating
and
Refer to Table C for
FM
Sensitivity Rating

REC. PENDENT
K=11.2 (TY5237)
K=14.0 (TY6237)
With Style 30
Escutcheon
UPRIGHT
K=11.2 (TY5137)
K=14.0 (TY6137)
and
PENDENT
K=11.2 (TY5237)
K=14.0 (TY6237)
REC. PENDENT
K=11.2 (TY5237)
K=14.0 (TY6237)
With Style 40
Escutcheon

TEMP.

BULB
LIQUID

135F/57C

Orange

155F/68C

Red

175F/79C

Yellow

200F/93C

Green

286F/141C

Blue

135F/57C

Orange

155F/68C

Red

175F/79C

Yellow

200F/93C

Green

286F/141C

Blue

135F/57C

Orange

155F/68C

Red

175F/79C

Yellow

200F/93C

Green

286F/141C

Blue

135F/57C

Orange

155F/68C

Red

175F/79C

Yellow

200F/93C

Green

NATURAL
BRASS

CHROME
PLATED

WHITE*
POLYESTER

LEAD
COATED

1, 2, 3**, 4

1, 2, 4

1, 2, 4

1, 2, 3, 4
N/A
1, 2, 4

1, 2, 3, 4
1, 2, 3, 4
1, 2, 4

1, 2, 4

N/A

NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL).
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL).
3. Approved by Factory Mutual Research Corporation (FM).
4. Approved by the City of New York under MEA 177-03-E.
5. Where Polyester Coated or Lead Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion Resistant
Sprinklers.
* Frame and Deflector only. Listings and approvals apply to color (Special Order).
** Pendent Only.
N/A: Not Available

TABLE A, LABORATORY LISTINGS AND APPROVALS

TFP220_EN 

Page3 of 8

LIGHTHAZARD

ORDINARY HAZARD

57C

68C

79C

93C

141C

57C

68C

79C

93C

141C

AREA

STYLE

14 x 14
14 x 14
14 x 14

Up. or Pend.
Style 30 Recessed
Style 40 Recessed

QR
QR
QR

QR
QR
QR

QR
QR
QR

QR
QR
QR

SR
N/A
N/A

16 x 16
16 x 16
16 x 16

Up. or Pend.
Style 30 Recessed
Style 40 Recessed

QR*
QR*
N/A

QR*
QR*
N/A

QR*
QR*
N/A

QR*
QR*
N/A

QR*
QR*
N/A

SR
SR
SR

SR
SR
SR

SR
SR
SR

SR
SR
SR

SR
N/A
N/A

18 x 18
18 x 18
18 x 18

Up. or Pend.
Style 30 Recessed
Style 40 Recessed

QR*
QR*
N/A

QR*
QR*
N/A

QR*
QR*
N/A

QR*
QR*
N/A

QR*
QR*
N/A

SR
SR
SR

SR
SR
SR

SR
SR
SR

SR
SR
SR

SR
N/A
N/A

20 x 20
20 x 20
20 x 20

Up. or Pend.
Style 30 Recessed
Style 40 Recessed

QR*
QR*
N/A

QR*
QR*
N/A

QR*
QR*
N/A

SR*
SR*
N/A

SR*
SR*
N/A

SR
SR
SR

SR
SR
SR

SR
SR
SR

SR
SR
SR

SR
N/A
N/A

QR: Quick Response

SR: Standard Response
N/A: Not Applicable
* Does not apply to Upright K = 14.0

TABLE B
SENSITIVITY RATING FOR UL AND C-UL LISTING OF SERIES EC-11 OR EC-14 SPRINKLERS
(SEE TABLE D FOR PERMITTED K-FACTOR/AREA COMBINATIONS)

LIGHTHAZARD

ORDINARY HAZARD

57C

68C

79C

93C

141C

57C

68C

79C

93C

141C

AREA

STYLE

14 x 14
14 x 14
14 x 14

Up. or Pend.
Style 30 Recessed
Style 40 Recessed

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

16 x 16
16 x 16
16 x 16

Up. or Pend.
Style 30 Recessed
Style 40 Recessed

QR*
QR*
N/A

QR*
QR*
N/A

N/A
N/A
N/A

N/A
N/A
N/A

N/A
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

18 x 18
18 x 18
18 x 18

Up. or Pend.
Style 30 Recessed
Style 40 Recessed

QR*
QR*
N/A

QR*
QR*
N/A

N/A
N/A
N/A

N/A
N/A
N/A

N/A
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

20 x 20
20 x 20
20 x 20

Up. or Pend.
Style 30 Recessed
Style 40 Recessed

QR*
QR*
N/A

QR*
QR*
N/A

N/A
N/A
N/A

N/A
N/A
N/A

N/A
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

SR
N/A
N/A

QR: Quick Response

SR: Standard Response
N/A: Not Applicable
* Pendent Only

TABLE C
SENSITIVITY RATING FOR FM APPROVAL OF SERIES EC-11 OR EC-14 SPRINKLERS
(SEE FM LOSS PREVENTION DATA SHEET 2-8N FOR PERMITTED K-FACTOR/AREA COMBINATIONS)

Page4 of 8

TFP220_EN

Technical
Data

Design
Criteria

Approvals
UL and C-UL Listed. FM Approved. (Refer to
Table A for complete approval information
including corrosion resistant status. The approvals apply to the service conditions indicated in the Design Criteria section.)

The Series EC-11 and EC-14 Extended Coverage Sprinklers must only be installed in
accordance with the applicable UL and CUL Listing or FM Approval requirements
as indicated below. Only the Style 30 or 40
Recessed Escutcheon is to be used for recessed installation, as applicable (Ref. Table
A, B, and C).

Maximum Working Pressure

175 psi (12,1 bar)
Pipe Thread Connection
3/4 inch NPT
Discharge Coefficients
K = 11.2 GPM/psi1/2
(161,3 LPM/bar1/2)
K = 14.0 GPM/psi1/2
(201,6 LPM/bar1/2)
Temperature Ratings
135F/57C to 286F/141C

UL and C-UL Listing

Requirements
1.

The Series EC-11 and EC-14 Sprinklersmay

be used for the coverage areas shown in
Table D, based on maintaining the minimum specified flow rate as a function of
coverage area and hazard group for all of
the sprinklers in the design area.

2.

The Series EC-11 and EC-14 Sprinklers are

permitted to be used with unobstructed or
non-combustible obstructed ceiling construction as defined and permitted by NFPA
13. For example:

Finish
Sprinkler: Refer to Table A
Recessed Escutcheon: White Coated,
Chrome Plated, and Brass Plated
Physical Characteristics
Frame............................................................Bronze
Button...........................................................Bronze
Sealing Assembly..................................................
.................................. Beryllium Nickel w/Teflon
Bulb.............................................Glass (3mmdia.)
Compression Screw.................................Bronze
Deflector......................................................... Brass

Unobstructed, combustible or non-- combustible, ceiling construction with a deflector to ceiling/roof deck distance of 1 to 12
inches (25 to 300 mm).
Obstructed, non-combustible, ceiling
construction with a deflector location below
structural members of 1 to 6 inches (25
to 150 mm) and a maximum deflector to
ceiling/roof deck distance of 22 inches (550
mm).
3.

The Series EC-11 and EC-14 Sprinklers having been specifically tested and listed for
non-combustible obstructed construction
are permitted to be used within trusses
or bar joists having non-combustible web
members greater than 1 inch (25.4 mm)
when applying the 4 times obstruction
criteria rule defined under Obstructions to
Sprinkler Discharge Pattern Development.

4.

The minimum allowable spacing between

the Series EC-11 and EC-14 Sprinklers, to
prevent cold soldering, is 8 feet (2,4m) for
upright sprinklers and 9 feet (2,7 m) for
pendent sprinklers.

5.

The Series EC-11 and EC-14 Sprinklers are

to be installed in accordance with all other
requirements of NFPA 13 for extended
coverage upright and pendent sprinklers.
For example:

Patents
U.S.A. Patent Numbers 5,366,022; 5,579,846;
5,584,344; 5,609,211; 5,862,994; and
5,865,256.

Operation
The glass bulb contains a fluid which expands when exposed to heat. When the
rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb,
which then allows the sprinkler to activate
and flow water.

obstructions to sprinkler discharge, obstructions to sprinkler pattern development,

obstructions to prevent sprinkler discharge
from reaching hazard, clearance to storage,

etc.
UL and C-UL Specific Application Listing Requirements For Installation Under
Concrete Tees The Series EC-11 and EC-14
Extended Coverage Upright and Pendent
Sprinklers (TY5137, TY5237, TY6137 &
TY6237) have a UL and C-UL Specific Application Listing for use under concrete tees
when installed as follows:
1.

The stems of the concrete tee construction

must spaced at less than 7.5 feet (2,3 m) on
center but more than 3 feet (0,9 m) on center. The depth of the concrete tees must not
exceed 30 inches (762 mm). The maximum
permitted concrete tee length is 32 feet (9,8
m); however, where the concrete tee length
exceeds 32 feet (9,8 m), non-combustible
baffles, equal in height to the depth of
the tees, can be installed so that the space
between the tees does not exceed 32 feet
(9,8 m) in length.

2.

The sprinkler deflectors are to be located in

a horizontal plane at or above 1 inch (25,4
mm) below the bottom of the concrete tee
stems.

3.

When the sprinkler deflectors are located

higher than a horizontal plane 1 inch (25l,4
mm) beneath the bottom of the concrete
tee stems, the obstruction to sprinkler
discharge criteria requirements of NFPA 13
for extended coverage upright sprinklers
applies.

FM Approval
Requirements
The Series EC-11 and EC-14 Extended Coverage Sprinklers are to be installed in accordance with the applicable Factory Mutual
Loss Prevention Data Sheet for limited use
in buildings of specific roof construction
and for the protection of certain specific
ordinary hazard (non-storage and/or nonflammable or combustible liquid) occupancies. Information provided in the FM Loss
Prevention Data Sheets relate to, but are not
limited to, hydraulic design, ceiling slope
and obstructions, minimum and maximum
allowable spacing, and deflector-to ceiling
distance. These criteria may differ from UL
and/or NFPA criteria, therefore the designer
should review and become familiar with
Factory Mutual requirements before proceeding with design.

TFP220_EN 

1/21/8
(12,73,2 mm)
FACE OF
SPRINKLER
FITTING

Page5 of 8

2-7/8 DIA.
(73,0 mm)
2-1/4 DIA.
(57,2 mm)

1/2 (12,7 mm)

1/4 (6,4 mm)

FITTING SIDE
TOWARDS SPRINKLER
FITTING

1/8
(3,2 mm)
WRENCH
RECESS
(END A)

MOUNTING
SURFACE

MOUNTING
PLATE

CLOSURE
1-3/8 (34,9 mm)
1-1/8 (28,6 mm)

FIGURE 4
W-TYPE 3 SPRINKLER
WRENCH

WRENCH
RECESS

FIGURE 2
SERIES EC-11 AND EC-14 RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 30 RECESSED ESCUTCHEON

5/81/4
(15,96,4 mm)
FACE OF
SPRINKLER
FITTING

MOUNTING
SURFACE
CLOSURE

2-7/8 DIA.
(73,0 mm)
2-1/4 DIA.
(57,2 mm)

3/4 (19,1 mm)

1/4 (6,4 mm)
1/8
(3,2 mm)

MOUNTING
PLATE
1-3/8 (34,9 mm)
7/8 (22,2 mm)

FIGURE 3
SERIES EC-11 AND EC-14 RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 40 RECESSED ESCUTCHEON

FIGURE 5
W-TYPE 22 RECESSED
SPRINKLER WRENCH

WRENCH
HEX

Page6 of 8

TFP220_EN

LIGHT HAZARD
0.10 GPM/FT2

GROUP I
ORDINARY HAZARD
0.15 GPM/FT2

GROUP II
ORDINARY HAZARD
0.20 GPM/FT2

DESCRIPTION

AREA

GPM

PSI

GPM

PSI

GPM

PSI

TY5137 (K=11.2) UPRIGHT

14 x 14
16 x 16
18 x 18
20 x 20

30
33
40

7.2
8.7
12.8

30
39
49
60

7.2
12.1
19.1
28.7

39
51
65
80

12.1
20.7
33.7
51.0

TY5237 (K=11.2) PENDENT

14 x 14
16 x 16
18 x 18
20 x 20

30
33
40

7.2
8.7
12.8

30
39
49
60

7.2
12.1
19.1
28.7

39
51
65
80

12.1
20.7
33.7
51.0

TY6137 (K=14.0) UPRIGHT

14 x 14
16 x 16
18 x 18
20 x 20

N/A
N/A
N/A
N/A

N/A
N/A
N/A
N/A

39
49
60

7.8
12.3
18.4

51
65
80

13.3
21.6
32.7

TY6237 (K=14.0) PENDENT

14 x 14
16 x 16
18 x 18
20 x 20

37
37
40

7.0
7.0
8.2

39
49
60

7.8
12.3
18.4

51
65
80

13.3
21.6
32.7

1 ft. = 0.3048 m
1 ft2 = 0.093 m2
1 gpm = 3.785 lpm
1 psi = 0.06895 bar
1 gpm/ft2 = 40.74 mm/min

TABLE D
FLOW CRITERIA FOR UL AND C-UL LISTING OF SERIES EC-11 AND EC-14 SPRINKLERS

Installation
The Series EC-11 and EC-14 Sprinklers must
be installed in accordance with the following instructions:
NOTES
Do not install any bulb type sprinkler if the
bulb is cracked or there is a loss of liquid from
the bulb. With the sprinkler held horizontally,
a small air bubble should be present. The diameter of the air bubble is approximately
1/16 inch (1,6 mm) for the 135F/57C to 3/32
inch (2,4 mm) for the 286F/141C temperature ratings.
A leak tight 3/4 inch NPT sprinkler joint should
be obtained with a torque of 10 to 20 ft.lbs.
(13,4 to 26,8 Nm). A maximum of 30 ft.lbs.
(40.7 Nm) of torque is to be used to install
sprinklers. Higher levels of torque may distort
the sprinkler inlet with consequent leakage or
impairment of the sprinkler.
Do not attempt to compensate for insufficient
adjustment in an Escutcheon Plate by underor over-tightening the Sprinkler. Readjust the
position of the sprinkler fitting to suit.

Step 1. The sprinkler must be installed with

the deflector parallel to the mounting surface. Pendent sprinklers must be installed
in the pendent position, and upright sprinklers must be installed in the upright position.
Step 2. After installing the Style 30 or 40
mounting plate (or other escutcheon, as
applicable) over the sprinkler pipe threads
and with pipe thread sealant applied to the
pipe threads, hand tighten the sprinkler
into the sprinkler fitting.
Step 3. Wrench tighten upright or pendent
sprinklers using only the W-Type 3 (End A)
Sprinkler Wrench. Wrench tighten the recessed pendent sprinklers using only the
W-Type 22 Sprinkler Wrench. The wrench
recess of the applicable sprinkler wrench
(Ref. Figure 4 and 5) is to be applied to the
sprinkler wrench flats (Ref. Figure 1).

TFP220_EN 

Care and
Maintenance
The Series EC-11 and EC-14 Sprinklers must
be maintained and serviced in accordance
with the following instructions:
NOTE
Before closing a fire protection system main
control valve for maintenance work on the
fire protection system that it controls, permission to shut down the affected fire protection
systems must be obtained from the proper
authorities and all personnel who may be affected by this actionmust be notified.

Sprinklers that are found to be leaking or

exhibiting visible signs of corrosion must
be replaced.
Automatic sprinklers must never be painted, plated, coated, or otherwise altered after leaving the factory. Modified sprinklers
must be replaced. Sprinklers that have
been exposed to corrosive products of
combustion, but have not operated, should
be replaced if they cannot be completely
cleaned by wiping the sprinkler with a cloth
or by brushing it with a soft bristle brush.
Care must be exercised to avoid damage
to the sprinklers - before, during, and after
installation. Sprinklers damaged by dropping, striking, wrench twist/slippage, or
the like, must be replaced. Also, replace any
sprinkler that has a cracked bulb or that has
lost liquid from its bulb. (Ref. Installation
Section).
Frequent visual inspections are recommended to be initially performed for corrosion resistant coated sprinklers, after the installation has been completed, to verify the
integrity of the corrosion resistant coating.
Thereafter, annual inspections per NFPA 25
should suffice; however, instead of inspecting from the floor level, a random sampling
of close-up visual inspections should be
made, so as to better determine the exact
sprinkler condition and the long term integrity of the corrosion resistant coating, as
it may be affected by the corrosive conditions present.

Page7 of 8

The owner is responsible for the inspection, testing, and maintenance of their fire
protection system and devices in compliance with this document, as well as with
the applicable standards of the National
Fire Protection Association (e.g., NFPA 25),
in addition to the standards of any other
authorities having jurisdiction. The installing contractor or sprinkler manufacturer
should be contacted relative to any questions.
It is recommended that automatic sprinkler
systems be inspected, tested, and maintained by a qualified Inspection Service in
accordance with local requirements and/or
national codes.

Limited Warranty
Products manufactured by Tyco Fire & Building Products (TFBP) are warranted solely to
the original Buyer for ten (10) years against
defects in material and workmanship when
paid for and properly installed and maintained under normal use and service. This
warranty will expire ten (10) years from
date of shipment by TFBP. No warranty is
given for products or components manufactured by companies not affiliated by
ownership with TFBP or for products and
components which have been subject to
misuse, improper installation, corrosion, or
which have not been installed, maintained,
modified or repaired in accordance with applicable Standards of the National Fire Protection Association, and/or the standards
of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at
TFBPs sole option. TFBP neither assumes,
nor authorizes any person to assume for it,
any other obligation in connection with the
sale of products or parts of products. TFBP
shall not be responsible for sprinkler system
design errors or inaccurate or incomplete
information supplied by Buyer or Buyers
representatives.
In no event shall TFBP be liable, in contract,
tort, strict liability or under any other legal theory, for incidental, indirect, special
or consequential damages, including but
not limited to labor charges, regardless of
whether TFBP was informed about the possibility of such damages, and in no event
shall TFBPs liability exceed an amount
equal to the sales price.
The foregoing warranty is made in lieu of
any and all other warranties express or
implied, including warranties of merchantability and fitness for a particular purpose.
This limited warranty sets forth the exclusive remedy for claims based on failure of
or defect in products, materials or components, whether the claim is made in contract, tort, strict liability or any other legal
theory.
This warranty will apply to the full extent
permitted by law. The invalidity, in whole or
part, of any portion of this warranty will not
affect the remainder.

Page8 of 8

TFP220_EN

Ordering
Procedure
When placing an order, indicate the full
product name. Please specify the Sprinkler
Identification Number (SIN), quantity, and
temperature rating.Refer to the Price List
for complete listing of Part Numbers.
Contact your local distributor for availability.

P/N 51 - AAA - B -CCC

AAA = 893 (for TY5237

K11.2 Pendent)
AAA = 894 (for TY5137

K11.2 Upright)
AAA = 895 (for TY6237

K14.0 Pendent)
AAA = 896 (for TY6137

K14.0 Upright)

Sprinkler Assemblies with NPT Thread

Connections:
Specify: (specify SIN), (specify K-Factor),
(specify temperature rating), (specify Pendent or Upright) Extended Coverage Sprinkler with (specify finish), P/N (specify - from
Table E, where applicable).

B = 1 (for Natural Brass)

B = 3 (for White [RAL9010])*
B = 4 (for White Polyester)
B = 7 (for Lead Coated)
B = 9 (for Chrome Plated)

Recessed Escutcheon:
Specify: Style (specify 30 or 40) Recessed
Escutcheon with (specify finish), P/N (specify).

CCC = 135 (for 135F/57C)

CCC = 155 (for 155F/68C)
CCC = 175 (for 175F/79C)
CCC = 200 (for 200F/93C)

Style 30 Recessed Escutcheon

Chrome Plated .................. PSN 56-705-9-011
White Color Coated...........PSN 56-705-4-011
White (RAL9010)*...............PSN 56-705-3-011
Brass Plated..........................PSN 56-705-2-011

*Eastern Hemisphere sales only.

TABLE E
PART NUMBERS FOR
EC-11 AND EC-14 SPRINKLERS

Style 40 Recessed Escutcheon

Chrome Plated.....................PSN 56-700-9-010
White Color Coated...........PSN 56-700-4-010
White (RAL9010)*...............PSN 56-700-3-010
Brass Plated..........................PSN 56-700-2-010
*Eastern Hemisphere sales only.
Sprinkler Wrench:
Specify: W-Type 3 Sprinkler Wrench,
P/N 56-895-1-001
Specify: W-Type 22 Recessed SprinklerWrench, P/N 56-665-7-001

Note: This document is a translated document. Translations of any materials into languages other than English are intended solely as a convenience to the non-English-reading
public. Translation accuracy is neither guaranteed nor implied. If any questions arise related to the accuracy of the information contained in the translation, please refer to the
English version of document TFP220 which is the official version of the document. Any discrepancies or differences created in the translation are not binding and have no legal
effect for compliance, enforcement or any other purposes. www.quicksilvertranslate.com.

TYCO
FIRE PRODUCTS,
451451
North
Cannon
Avenue,
Lansdale,
Pennsylvania
19446 19446
TYCO FIRE
& BUILDING
PRODUCTS,
North
Cannon
Avenue,
Lansdale,
Pennsylvania