DAQ Presentation - F

PC Based Data Acquisition
K. Poddar
National Wind Tunnel Facility

IIT Kanpur
Presentation Overview
Virtual instrumentation
Data acquisition system components
Data acquisition fundamentals
LabVIEW based data acquisition
Examples
Overview of Virtual Instruments and Measurements

Virtual instrumentation combines hardware and software with industry-standard
computer technologies to create user-defined instrumentation solutions. We
can have plug-in and distributed hardware and driver software for DAQ, IEEE
488 (GPIB), PXI, serial, and industrial communications.
The driver software is the application programming interface (API) to the hardware.
Application software can be LabVIEW, LabWindows/CVI , and any other software.
Taking Measurements with Virtual Instruments
Different hardware and software components can make up a virtual instrumentation

system. We can use a variety of hardware components to monitor or control a
process or to test a device. We can connect the hardware to the computer and
understand how the hardware takes measurements, and incorporate hardware
into a virtual instrumentation system.
Data Acquisition: System Components

Today, most scientists and engineers use personal computers (PCs)
with PCI, PXI/CompactPCI, PCMCIA, USB, IEEE 1394, ISA, or parallel
or serial ports for data acquisition in laboratory research, test and
measurement, and industrial automation. Many applications use plug-in
devices to acquire data and transfer it directly to computer memory.
Obtaining proper results from a PC-based DAQ system depends on each
of the following system elements:
Transducers
Signal Conditioning
DAQ Hardware
Software
The PC
DAQ System Components
DAQ System
Components
Transducers
Signal Conditioning
DAQ Hardware: A/D Board

The simplest way to measure a signal is with a voltmeter; however
some experiments require the use of computers to synchronize
data acquisition and record large quantities of data.
An Analog-to-Digital (A/D) board plugs into an expansion slot of a
personal computer and is the means for digitizing and storing the
analog voltage signals from various sensors. The digital data is
then saved on the computers hard disk.
An A/D board does not record continuous records (like a strip chart
or seismograph), but rather it records instantaneous values of the
signals through different channels at a discrete sampling frequency.
This allows post-processing of the digitized signal by manipulating
a series of data points after they are acquired.
Data Acquisition: Single-ended Analog Input
Data Acquisition: Differential Analog Input
Data Acquisition: A/D Multiplexing
DAQ: Sampling Rate & Multiplexing
DAQ: Other Considerations
DAQ Software
Software transforms the PC and the DAQ hardware into a complete
data acquisition, analysis, and display system.
DAQ hardware without software is useless and DAQ hardware
with poor software is almost useless.
The majority of DAQ applications use driver software. Driver software
is the layer of software that directly programs the registers of the DAQ
hardware, managing its operation and its integration with the computer
resources, such as processor interrupts, DMA, and memory. Driver
software hides the low-level, complicated details of hardware
programming, providing the user with an easy-to-understand interface.
DAQ Fundamentals
Measurement System
This figure depicts the measurement

system overview, showing the path
of real-world physical phenomena
to your measurement application.
Signal Types
A signal is classified as analog or digital by the way it conveys information.
A digital signal has only two possible discrete levels-high level or low level.
An analog signal, on the other hand, contains information in the continuous
variation of the signal with respect to time. A breakdown of the main signal
types is shown below.
Analog Signals
To measure analog signals properly, we must know
Signal source:
Grounded or Floating
Measurement system to use: Differential, RSE, or NRSE
Signal Sources
Grounded Signal Sources
Floating Signal Sources
Measurement System Types

Differential
RSE
NRSE
Measuring Floating & Grounded Signals

Measuring Floating Signal Sources
You can measure floating signal sources with both differential and
single-ended measurement systems.
Measuring Grounded Signal Sources

A grounded signal source is best measured with a differential or an
NRSE measurement system. If you use an RSE measurement system
with a grounded source, the result is typically a noisy measurement
system often showing power-line frequency (60 Hz) components in
the readings. Ground-loop induced noise can have both AC and DC
components, introducing offset errors and noise in the measurements.
Measurement System Types and Signal Sources
Signal Conditioning
The manipulation of signals to prepare them for digitizing is called
signal conditioning. Common types of signal conditioning include
the following:
Amplification
Filtering
Linearization
Transducer Excitation
Isolation
Sampling Considerations
Device range
Limit settings
Resolution
Code width
Sampling rate
Resolution
Resolution is the smallest amount of input signal change that a
device or sensor can detect. The number of bits that an ADC uses
to represent the analog signal is the resolution. The higher the
resolution, the larger the number of divisions the range is broken
into, and therefore, the smaller the detectable voltage change.
Code Width
The range, resolution, and gain available on a DAQ device determine the
smallest detectable change in voltage. This change in voltage represents 1
least significant bit (LSB) of the digital value and is often called the code
width.
Sampling Rate
One of the most important parameters of an analog input or output system
is the rate at which the measurement device samples an incoming signal or
generates the output signal. The sampling rate determines how often an
analog-to-digital (A/D) or digital-to-analog (D/A) conversion takes place.
A fast input sampling rate acquires more points in a given time and can form
a better representation of the original signal than a slow sampling rate.
Sampling too slowly results in a poor representation of the analog signal.
Under-sampling causes the signal to appear as if it has a different frequency
than it actually does. This misrepresentation of a signal is called aliasing.
Aliasing
Alias Freq. = ABS (Closest Int. Mult. of Sampling Freq. - Input Freq. )
Determining How Fast to Sample

For frequency measurements, according to the Nyquist theorem, you must
sample at a rate greater than twice the maximum frequency component in
the signal you are acquiring to accurately represent the signal.
Triggering
A trigger is a signal that causes an action, such as
starting the acquisition of data.
Analog trigger
Digital trigger
Programming Flowcharts
Analog Input Programming Flowcharts
Single Sample Analog Input
Finite Analog Input
Continuous Analog Input
Triggered Acquisition
Single Sample Flowchart
Finite Sample Flowchart
Continuous Sample Flowchart
Analog Output Programming Flowcharts

Single Sample Analog Output
Finite Analog Output
Continuous Analog Output

DAQ Presentation - F

Uploaded by

Copyright:

Available Formats

DAQ Presentation - F

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DAQ Presentation - F

Uploaded by

Copyright:

Available Formats

PC Based Data Acquisition

National Wind Tunnel Facility

Overview of Virtual Instruments and Measurements

Different hardware and software components can make up a virtual instrumentation

Data Acquisition: System Components

DAQ System Components

DAQ Hardware: A/D Board

Data Acquisition: Single-ended Analog Input

Data Acquisition: Differential Analog Input

Data Acquisition: A/D Multiplexing

DAQ: Sampling Rate & Multiplexing

DAQ: Other Considerations

This figure depicts the measurement

Measurement system to use: Differential, RSE, or NRSE

Floating Signal Sources

Measurement System Types

Measuring Floating & Grounded Signals

Measuring Grounded Signal Sources

Measurement System Types and Signal Sources

Determining How Fast to Sample

DAQ System Components

DAQ System Components

Single Sample Flowchart

Finite Sample Flowchart

Continuous Sample Flowchart

Analog Output Programming Flowcharts

You might also like