SOR Civil Works - Assam PWD Schedule - 2013-14

Page-1
CH-1: EARTHWORK
Item no
1.1
Description
Unit
Rate
EARTHWORK IN EXCAVATION
Earthwork in excavation for foundation trenches of walls, retaining walls, footings
of column, steps, septic tank etc. including refilling (return filling) the quantity as
necessary after completion of work, breaking clods in return filling, dressing,
watering and ramming etc. and removal of surplus earth with all lead and lifts as
directed and specified in the following classification of soils including bailing out
water where necessary as directed and specified.
(A) Up to a depth of 2.00m below the existing ground level.
(a) In ordinary soil
Cum
Rs.108.82
(b) In hard/ dense soil
Cum
Rs.138.12
(c) In soft or laminated rock or medium shale
Cum
Rs.182.14
(i) Using blasting materials
Cum
Rs.442.42
(ii) Without using blasting materials
Cum
Rs.372.27
(i) Using blasting materials
Cum
Rs.540.27
(ii) Without using blasting materials (where blasting is not possible/ not
permissible)
Cum
Rs.579.64
(B) Extra over item no.1.1(A) above for each 1m depth or part thereof beyond the
initial depth of 2m
Cum
Rs.30.79
Shuttering and shoring the earth at different levels in foundations where necessary
with required prop, struts, planks, timbers, nails etc. including dewatering if
necessary, complete as directed and specified (measurement to be taken in the
face area timbered)
(a) Upto a depth of 1.5 metre
Cum
Rs.75.38
(b) Above 1.5 m upto 3.00 m depth
Cum
Rs.78.89
(c) Above 3.00 m upto 4.50 m depth
Cum
Rs.80.62
(d) Above 4.50 m upto 6.00 m depth
Cum
Rs.82.24
(a) With earth or silt or sand obtained by head load with lead upto 90m and lift
upto 2m
Cum
Rs.105.25
(i) Extra for each 30m lead or part thereof beyond the initial lead of 90m (by head
load)
Cum
Rs.13.92
(ii) Extra for each 1.5m lift or part thereof beyond the initial lift of 2.00m (by head
load)
Cum
Rs.6.96
(b) With hill sand obtained by truck carriage loading and unloading, and carriage to
the site of work.
Cum
Rs.333.77
(c) With river sand or silt (predominantly non plastic) by truck carriage including
loading and unloading.
Cum
Rs.345.61
(d) In medium rock of hard shale
(e) In hard rock
1.2
1.3
Ch-1 : Earth Work
Earth/ sand filling in plinth in layers not more than 150mm thick including
necessary carriage, watering, ramming etc. complete as directed and specified
including payment of land compensation, forest royalty, sales tax and other duties
and taxes as may be necessary.
Page-2
Item no
Description
Unit
(d) With stone dust obtained by truck carriage including loading and unloading to
the site of work.
Cum
Rs.428.51
(e) Extra cost for lifting of sand for filling of sunk floor for each subsequent floors
above the ground floor as directed and specified.
Cum
Rs.15.30
(a) Within Guwahati city only
Cum
Rs.276.81
(b) Other than Guwahati city
Cum
Rs.210.20
1.5
Earth work in excavation in slushy/ marshy soil, decomposed organic matter mixed
with brickbats, broken glass panes, broken earthen pots etc. removal of stumps and
other deleterious matter in the proposed building site including constant water
pumping for bailing out water as directed including return filling and ramming after
completion of work with good quality earth (measurement will be on the basis of
profile or section measurement).
Cum
Rs.236.24
1.6
Supplying and filling sand gravel in foundation trenches of column footings over
slushy soil including local carriage of materials within 8 km pumping out of water,
ramming etc. complete for strengthening the bearing capacity of the soil as
directed and specified including payment of Forest Royalty and Sales Tax and other
duties and taxes as may be necessary.
Extra lead per km truck carriage for sand gravel beyond the initial lead of 8 km.
Cum
Rs.764.30
Cum
Rs.7.04
1.4
1.7
Ch-1 : Earth Work
Rate
Raising low site around the building with approved soil obtained from outside by
truck carriage including breaking clods, dressing etc. complete including paying
necessary forest royelty, sales tax, land compensation, municipal gate fees, if any
monopoly duty etc. (profile measurement to be taken and 12.5% deduction for
shrinkage to be made from total quantity) etc. complete as directed and specified.
Page-3
CH-2: CEMENT CONCRETE WORKS

Item
Description
no
2.1 PLAIN CEMENT CONCRETE WORKS
2.1.1 Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in
foundation bed for footing steps, walls, brick works etc. as directed and specified
including dewatering if necessary, and curing complete (shuttering where
necessary shall be measured and paid separately).
Unit
Rate
(a) In prop 1cement: 3 sand :6 coarse aggregate by volume
cum
Rs. 4,292.86
(b) In prop 1cement: 4 sand :8 coarse aggregate by volume
cum
Rs. 3,890.61
(c) In prop 1cement: 5 sand :10 coarse aggregate by volume
cum
Rs. 3,569.75
(d) In prop 1cement: 6 sand :12 coarse aggregate by volume
cum
Rs. 3,366.38
a) 35mm thick
sqm
Rs. 193.90
b) 50mm thick
sqm
Rs. 253.28
c) 100mm thick
sqm
Rs. 491.91
sqm
Rs. 181.99
(a) 35mm thick
sqm
Rs. 192.13
(b) 50mm thick
sqm
Rs. 253.64
2.1.2 Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified
with coarse agg. of size 13mm to 32mm including dewatering if necessary, and
curing etc. complete.
2.1.3 Providing and laying 25mm thick damp proof course with cement concrete in prop
1:1.5:3 with graded stone agg. of 10mm down nominal size including providing
approved damp proof admixture in proportion as recommended by the
manufacturer including curing etc. complete as directed.
2.1.4 Plain cement concrete apron in prop 1:4:8 with 20mm down graded coarse agg.
Over soling including neat cement finish using cement slurry 2.75Kg. of cement per
sq.m. of floor (soling to be measured separately).
2.2 REINFORCED CEMENT CONCRETE WORKS

2.2.1 Providing and laying plain/reinforced cement croncrete works cement, coarse sand
& 20mm down graded stone aggregate including dewatering if necessary, and
curing complete but excluding cost of form work and reinforcement for reinforced
cement concrete work (form work and reinforcement will be measured and paid
separately)
(I) Using Mixer Machine
(A) In substructure up to plinth level
Foundation, footing, columns with base tie and plinth beam, pile cap, base slab,
retaining walls, walls of septic tank, inspection pit and the like and other works not
less than 100mm thick up to plinth level.
cum
N) Without using admixture, plasticiser

a) M15 grade concrete or Prop. 1:2:4
cum
Rs. 5,496.65
b) M20 grade concrete or Prop. 1:1.5:3
cum
Rs. 6,063.65
c) M25 grade concrete
cum
Rs. 6,603.01
d) M30 grade concrete
cum
Rs. 6,672.15
e) M35 grade concrete
cum
Rs. 6,801.22
P) Using admixture, plasticiser etc for air entraining, water reducing purposes
including addition of agent for changing normal setting time of concrete as
required.
Ch-2 : Cement Concrete Work
Page-4
Item
no
Description
Unit
Rate
cum
Rs. 5,717.17
cum
Rs. 6,329.48
cum
Rs. 6,911.89
cum
Rs. 6,986.58
cum
Rs. 7,125.95
cum
Rs. 5,668.82
cum
Rs. 6,241.39
cum
Rs. 6,786.00
cum
Rs. 6,855.86
cum
Rs. 6,986.19
cum
Rs. 5,889.34
cum
Rs. 6,507.22
cum
Rs. 7,094.88
cum
Rs. 7,170.29
cum
Rs. 7,310.92
cum
Rs. 5,758.89
cum
Rs. 6,331.46
cum
Rs. 6,876.08
cum
Rs. 6,945.94
cum
Rs. 7,076.26
(B) In super structure from plinth level up to 1st floor level.

i) Walls (thickness not less than 100mm) including attached pillasters, buttresses,
plinth and string course etc.
P) Using admixture, plasticiser etc for air entraining, water reducing purposes
including addition of agent for changing normal setting time of concrete as
required.
ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support,
balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except
spiral staircase and landing ) including preparing the top surface and finishing of
nosing.
P) Using admixture, plasticiser etc

Rs. 5,979.41
Rs. 6,597.29
Rs. 7,184.96
Rs. 7,260.37
Rs. 7,400.99
iii) Vertical and horizontal fins (thickness not more than 100mm) individually or
forming box louvre and projected band.
cum
Rs. 6,202.05
Page-5
Item
no
Description
Unit
Rate
cum
Rs. 6,774.62
cum
Rs. 7,319.24
cum
Rs. 7,389.09
cum
Rs. 7,519.42

Rs. 6,422.57
Rs. 7,040.45
Rs. 7,628.12
Rs. 7,703.52
Rs. 7,844.15
iv) On domes, vaults and shell roof

cum
Rs. 6,328.84
cum
Rs. 6,906.96
cum
Rs. 7,456.88
cum
Rs. 7,527.39
cum
Rs. 7,658.99
cum
Rs. 6,549.36
cum
Rs. 7,172.79
cum
Rs. 7,765.76
cum
Rs. 7,841.82
cum
Rs. 7,983.72
cum
Rs. 5,812.96
cum
Rs. 6,363.40
cum
Rs. 6,886.98
cum
Rs. 6,954.11
cum
Rs. 7,079.41
f) M40 grade concrete (PSC Grade)
cum
Rs. 7,173.39
g) M45 grade concrete (PSC Grade)
cum
Rs. 7,504.54
h) M50 grade concrete (PSC Grade)
cum
Rs. 7,737.24
i) M55 grade concrete (PSC Grade)
cum
Rs. 8,104.20
cum
Rs. 6,033.48
cum
Rs. 6,629.23
cum
Rs. 7,195.86
cum
Rs. 7,268.54
II. Using Batching Plant/ RMC/ Truck mounted batching plant including Transit
Mixer and Concrete Pump
Page-6
Item
no
Description
Unit
Rate
cum
Rs. 7,404.14
cum
Rs. 7,505.85
cum
Rs. 7,864.24
cum
Rs. 8,116.09
cum
Rs. 8,513.23
cum
Rs. 220.52
cum
Rs. 265.83
cum
Rs. 308.88
cum
Rs. 314.43
cum
Rs. 324.73
cum
Rs. 332.46
cum
Rs. 359.70
cum
Rs. 409.03
cum
Rs. 378.85
cum
Rs. 306.19
2.2.2 Extra for using plasticiser in concrete if admixture, plasticiser etc are not included
in the item rate
2.2.3 Extra over item Nos. 2.2.1 (I) (B), above for each subsequent floor or part thereof
above the 1st floor level.
Page-7
CH-3: SHUTTERING WORKS

Item
No.
3.1
3.1.1
Description
Unit
Rate
TIMBER SHUTTERING (FORMWORK)
Providing form work of ordinary timber planking so as to give a rough finish

including centering, shuttering, strutting and propping etc., height of propping and
centering below supporting floor to ceiling not exceeding 4.0M and removal of the
same for in-situ reinforced concrete and plain concrete work in:
3.1.1.1 Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc.
(a) Using 38mm thick plank
Sqm
Rs.276.07
(b) Using 25mm thick plank
Sqm
Rs.252.24
Sqm
Rs.364.29
Sqm
Rs.341.90
Sqm
Rs.394.81
Sqm
Rs.364.01
Sqm
Rs.531.15
(i) Using 38mm thick plank
Sqm
Rs.212.37
(ii) Using 25mm thick plank
Sqm
Rs.202.44
Sqm
Rs.377.93
Sqm
Rs.452.94
Sqm
Rs.429.93
Sqm
Rs.492.38
Sqm
Rs.10,526.85
Sqm
Rs.512.08
Sqm
Rs.489.24
Sqm
Rs.785.13
Sqm
Rs.744.95
3.1.1.2 Sides of tie beams, grade beams etc. at or below ground level.
3.1.1.3 Columns, Pillars, Posts & Strut

(a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane
vertical face
(b) Circular or curved in plan (Using 38mm thick plank)
3.1.1.4 Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels
and horizontal ties.
(a) For depth not exceeding 1.0M.
(b) For depth exceeding 1.0M (Using 38mm thick plank).

3.1.1.5 Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs,
chajjas, balconies and the like.
(a) Floors etc. upto 200mm in thickness.
(b) Floors etc. above 200mm in thickness (Using 38mm thick plank).
3.1.1.6 In Ribbed/ waffle slab including rib beams (measurements to be taken on flat
surface) (Using 38mm thick plank)
3.1.1.7 Sloping or Battering sufaces such as sloped slabs etc. including folded plates.
(a) Where inclination to horizontal plane does not exceed 30o requiring shuttering
only on the underside.
(b) Where inclination to horizontal plane exceeds 30 degrees where shuttering may
be provided both on under side & upper side, if required.
Ch-3 : Shuttering Work
Page-8
Item
Description
No.
3.1.1.8 Vertical surface such as walls (any thickness), parapet walls, partitions, walls of
septic tank, inspection pit and the like including attached pilasters, butresses, plinth
and string courses and the like.
Unit
Rate
Sqm
Rs.326.05
Sqm
Rs.303.19
Sqm
Rs.466.24
Sqm
Rs.441.68
Sqm
Rs.496.80
Sqm
Rs.2,626.95
3.1.1.12 Domes, Vaults and shell roofs having curved surface in both directions (only area of
the underside shall be measured for payment). (Using 38mm thick plank)
Sqm
Rs.5,483.35
3.1.2
Extra for each subsequent 1.0M height or part thereof beyond the initial height of
4.0M as mentioned in item no. 3.1.1
Sqm
Rs.43.10
3.1.3
Providing form work of ordinary timber planking and removal of the same in edges
of slabs and breaks in floors and walls etc. of in-situ reinforced concrete works upto
first floor level.
(a) Thickness not exceeding 200mm.
R.M.
Rs.178.37
(b) Thickness exceeding 200mm.
Sqm
Rs.823.21
3.1.4
Extra for each subsequent floor or part thereof above the First Floor level as
mentioned in item no. 3.1.1 & 3.1.3(b).
Sqm
Rs.23.19
3.1.5
mentioned in item no. 3.1.3(a).
R.M.
Rs.4.64
3.2
3.2.1
PLYBOARD SHUTTERING (FORMWORK)

Providing form work of 12mm thick Plywood Board so as to give a rough finish
including centering, shattering, strutting and propping etc., height of propping and
centering below supporting floor to ceiling not exceeding 4.0M and removal of the
same for in situ reinforced concrete and plain concrete work in:
Sqm
Rs.278.61
(a) For depth not exceeding 1.0M.
Sqm
Rs.231.00
(b) For depth exceeding 1.0M.
Sqm
Rs.280.86
Sqm
Rs.345.67
Sqm
Rs.379.50
Sqm
Rs.10,222.84
Sqm
Rs.383.09
3.1.1.9 Vertical ties, fins, sun breaker, louvers, bands, dropwalls etc.
3.1.1.10 Staircase with sloping or stepped soffits including risers and stringers but excluding
Landing. (Using 38mm thick plank)
3.1.1.11 Arches/ slabs having curved surface in one direction. (Using 38mm thick plank)
3.2.1.1 Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any
shape like Tee/L etc. having plane vertical face
3.2.1.2 Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels
and horizontal ties.
3.2.1.3 Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs,
chajjas, balconies and the like.
(a) Floors etc. upto 200mm in thickness.
(b) Floors etc. above 200mm in thickness.
surface)
Page-9
Item
No.
Description
(b) Where inclination to horizontal plane exceeds 30o where shuttering may be
provided both on under side & upper side, if required.
Unit
Rate
Sqm
Rs.573.00
3.2.1.6 Vertical surface such as walls (any thickness), parapet walls, partitions and the like
including attached pilasters, butresses, plinth and string courses and the like.
Sqm
Rs.225.65
3.2.1.7 Vertical ties, fins, sun breaker, louvers, bands, dropwalls etc.
Sqm
Rs.318.23
3.2.1.8 Staircase with sloping or stepped soffits including risers and stringers but excluding
Landing.
Sqm
Rs.390.30
3.2.2
Extra for each subsequent 1.0M height or part thereof beyound the initial height of
Sqm
Rs.39.82
3.2.3
Providing form work of 12mm thick Plywood board and removal of the same in
edges of slabs and breaks in floors and walls etc. of in-situ reinforced concrete
works upto first floor level.
(a) Thickness not exceeding 200mm.
R.M.
Rs.171.87
(b) Thickness exceeding 200mm.
Sqm
Rs.774.22
Sqm
Rs.23.19
R.M.
Rs.4.64
Sqm
Rs.116.95
Sqm
Rs.115.42
Sqm
Rs.142.53
Sqm
Rs.140.38
Sqm
Rs.157.78
3.3.1.5 Vertical surface such as walls (any thickness), Lift shafts, partitions and the like
Sqm
Rs.143.23
3.2.4
3.2.5
3.3
mentioned in item no. 3.2.1 & 3.2.3(b).
mentioned in item no. 3.2.3(a).
STEEL SHUTTERING:
Providing formwork using 2mm pressed bend shuttering plate of mild sheet and
tubular telescopic steel props including centering, shuttering, strutting and
propping etc. complete and removal of the same for in situ reinforced concrete and
plain concrete work in:
3.3.1
3.3.1.2 Sides and Soffits of Beams, beam haunchings, cantilever girders and bressumers.
3.3.1.3 Flat Surfaces such as soffits of suspended floors, roofs, landings and the like.
3.3.2
Extra for each subsequent 1.0M height or part thereof beyound the initial height of
Sqm
Rs.23.42
3.3.3
mentioned in item no. 3.4.1
Sqm
Rs.25.69
Sqm
Rs.1,084.16
3.4 L&T DOKA FORMWORK SYSTEM

3.4.1
Providing formwork using L&T-Doka formwork system with 12mm thick Plywood
Board sheathing supported by timber H-beams and steel props with tripods
including centering, shuttering, strutting and propping etc. complete and removal
of the same for in situ reinforced concrete and plain concrete work in:
Page-10
Item
Description
No.
3.4.1.2 Sides and Soffits of Beams, beam haunchings, cantilever girders and bressumers.
Unit
Rate
(a) Using Flex system for height of propping and centering below supporting floor
to ceiling upto 4.5m
Sqm
Rs.553.72
(b) Using H.D.T. system for height of propping and centering below supporting floor
to ceiling exceeding 4.5m and upto 6.0m.
Sqm
Rs.4,702.83
(a) Using Flex system for height of propping and centering below supporting floor
to ceiling upto 4.5m
Sqm
Rs.539.15
(b) Using H.D.T. system for height of propping and centering below supporting floor
to ceiling exceeding 4.5m and upto 6.0m.
Sqm
Rs.4,725.44
surface)
Sqm
Rs.991.26
Sqm
Rs.571.91
Sqm
Rs.703.58
3.4.1.6 Vertical surface such as walls (any thickness), Lift shafts, partitions and the like
Sqm
Rs.1,570.12
3.4.2
mentioned in item no. 3.4.1
Sqm
Rs.26.28
3.4.3
Providing scaffolding using L&T-Doka access scaffold system upto a height of 40m.
supported by frames of timber H-beams, bracings including suitable couplers, pins,
tower spindles and 2nd class timber plank platforms complete as specified and
directed by the department. (measurement to be taken on elevation area of the
building/ structure).
Sqm
Rs.50.22
3.4.1.3 Flat Surfaces such as soffits of suspended floors, roofs, landings and the like.
Page-11
Ch-4: MASONARY WORK

Item
No.
Description
Unit
Rate
4.1.1 Providing soling in foundation and under floor with stone/ best quality picked
jhama brick, sand packed and laid to level and in panel after preparing the
subgrade as directed including all labour and materials and if necessary
dewatering, complete.
(a).Brick on flat soling.
Sqm
Rs. 368.71
(b).Brick on edge soling
Sqm
Rs. 532.75
(c).Stone soling of thickness 150mm.
Sqm
Rs. 217.83
4.1.2 Filling sunken floor with broken jhama brick bats and sand including compacting
and supplying of materials complete as specified and directed for all levels.
Cum
Rs. 4,323.17
4.1.3 Extra cost for lifting of brickbats and sand for filling of sunk floor for each
subsequent floors above the ground floor as directed and specified.
Cum
Rs. 154.61
(a) In proportion 1:3.
Cum
Rs. 6,045.24
(b) In proportion 1:4.
Cum
Rs. 5,860.86
(c) In proportion 1:5.
Cum
Rs. 5,630.36
(d) In proportion 1:6.
Cum
Rs. 5,515.11
4.1.4 Brick work in cement morter with 1st class brick including racking out joints and
curing complete as directed.
(I) In Sub-structure upto plinth level including dewatering if necessary
(e) In proportion 1:1:6 (1 cement:1 lime: 6 sand)

(f) In proportion 1:1:9. (1 cement:1 lime: 9 sand)
Rs. 5,681.90
Cum
Rs. 5,438.21
(a) In proportion 1:3.(1 cement:3 sand)
Cum
Rs. 6,211.75
(b) In proportion 1:4.(1 cement:4 sand)
Cum
Rs. 6,027.36
(c) In proportion 1:5.(1 cement:5 sand)
Cum
Rs. 5,796.87
(d) In proportion 1:6.(1 cement:6 sand)
Cum
Rs. 5,681.61
(e) In proportion 1:1:6.(1 cement: 1 Lime :6 sand)
Cum
Rs. 5,848.41
(f) In proportion 1:1:9.(1 cement: 1 Lime :9 sand)
Cum
Rs. 5,604.71
Cum
Rs. 260.27
(a). In proportion 1:3.
Sqm
Rs. 1,390.26
(b). In proportion 1:4.
Sqm
Rs. 1,347.85
(c). In proportion 1:5.
Sqm
Rs. 1,294.84
(d). In proportion 1:6. Analysis for 1m3

(II) In superstructure above plinth level up to 1st floor level.
Sqm
Rs. 1,268.10
(a). In proportion 1:3.(1 cement:3 sand)
Sqm
Rs. 1,428.74
(b). In proportion 1:4.(1 cement:4 sand)
Sqm
Rs. 1,386.33
(c). In proportion 1:5.(1 cement:5 sand)
Sqm
Rs. 1,333.31
(d). In proportion 1:6.(1 cement:6 sand)
Sqm
Rs. 1,306.58
(II) In superstructure above plinth level up to 1st floor level.
4.1.5 Extra over item no. 4.1.5 above for brick work in each subsequent floor or part
thereof above 1st floor level.
4.1.6 230mm thick brick wall in cement morter with 1st class brick including racking out
joints and curing complete as directed in structure
(I) In Sub-structure upto plinth level including dewatering if necessary
Ch-4 : Masonry Work
Page-12
Item
No.
Description
Unit
4.1.7 Extra over item no. 4.1.6 (II) above for brick work in each subsequent floor or part
Rate
Sqm
Rs. 59.71
(a) In cement mortar in proportion 1:4.

(1 cement:4 sand)
Sqm
Rs. 653.01
(b) In cement mortar in proportion 1:5.

(1 cement:5 sand)
Sqm
Rs. 635.49
(c) In cement mortar in proportion 1:6.

(1 cement : 6 sand)
(B) 75 mm thick wall
Sqm
Rs. 620.28
Sqm
Rs. 486.60
Sqm
Rs. 464.48
Sqm
Rs. 452.03
4.1.9 112 mm thick reinforced brick wall in prop 1:5 reinforced with two lines of M.S
rod/ Tor steel as specified embeded in 38 mm thick concrete course in prop.1:2:4
with coarse agg. 12mm down at every fourth courses embeded with protruding rod
in column including curing etc.complete as directed ( M.S rod/Tor steel shall be
measured and paid separately) in super structure above plinth up to 1st floor level.
Sqm
Rs. 730.00
4.1.10 75 mm thick reinforced brick wall in prop 1:5 reinforced with one line of M.S rod/
Tor steel as specified embeded in 28 mm thick concrete course in prop.1:2:4 with
coarse agg. 12mm down at every third course embedded with protruding rod in
column complete as directed (M.S rod / Tor steel shall be measured and paid
separately) in super structure up to 1st floor level.
Sqm
Rs. 520.68
a) 112mm thick brick wall
Sqm
Rs. 645.17
b) 75mm thick brick wall
Sqm
Rs. 445.41
Sqm
Rs. 640.32
Sqm
Rs. 452.69
Sqm
Rs. 824.98
Sqm
Rs. 621.67
4.1.8 1st class brick nogged wall in cement mortar including racking out joints and curing
complete as directed in super structure above plinth up to 1st floor level
(protruding M.S rod/Tor steel of column to be embeded in cement mortar and will
be measured and paid separately)
(A) 112mm thick brick wall
(a) In cement mortar in proportion 1:3.

(b) In cement mortar in proportion 1:4.
(1 cement: 4 sand)
(c) In cement mortar in proportion 1:5.
(1 cement:3 sand)
(1 cement: 5 sand)
4.1.11 Brick wall in cement lime mortar in prop. 1 cement: 1 lime putty: 6 fine sand
including racking out joints and curing complete as directed in super structure
above plinth up to 1st floor level ( protruding M.S rod/Tor steel of column to be
embeded in cement mortar and will be measured and paid separately)
4.1.12 1st class brick nogged wall in lime mortar in prop. 1 lime : 2 fine sand including
racking out joints and curing etc complete as directed ( protruding M.S rod/Tor
steel of column to be embedded in cement mortar and will be measured and paid
separately) in super structure up to 1st floor level.
a) 112mm thick brick wall
b) 75mm thick brick wall
4.1.13 R.B walling in prop.1:3 reinforced with H.B wire netting made of 20 Gauge G.I wire
(diamond shape) in walls, railings, drop walls, parapet, fins, bands, mullions from
ground floor level in superstructure up to 1st floor level including racking out joints
and curing etc complete as directed (Protruding rods of columns to be tied with
H.B. wire netting)
(a) 112 mm thick RB walls
(b) 75 mm thick RB walls
Ch-4 : Masonry Work
Page-13
Item
No.
Description
Unit
Rate
4.1.14 Extra for brick walling for each subsequent floor or part thereof above the 1st floor
level.
4.2
(a) 112mm thick brick/ R.B wall
Sqm
Rs. 29.09
(b) 75 mm thick brick/R.B wall
Sqm
Rs. 21.43
(a) Random Rubble Masonry
Cum
Rs. 2,574.55
(b) Coarse Rubble Masonry
Cum
Rs. 2,672.81
Cum
Rs. 7,540.66
Cum
Rs. 7,612.36
Cum
Rs. 130.14
Sqm
Rs. 1,553.46
Sqm
Rs. 789.09
Sqm
Rs. 59.71
Sqm
Rs. 784.41
Sqm
Rs. 14.55
STONE MASONARY WORK
4.2.1 Stone masonary work in retaining wall, wing wall, abutment, foundation, steps,
plinth etc. in cement mortar in prop 1:6 with levelling course of 1:6:12 with both
faces hammer dressed including bonding, providing face stone, through stone and
centering including racking of joints, curing and supplying and all carriage of stone
as directed including payment of forest royalty and sales tax and carriage.
4.3
Cellular Light Weight concrete Block work
4.3.1 Cellular Concrete Block work using Cellular Light Weight concrete block of Size
500x200x100mm conforming to IS-2185 Pt-3 or pt-4 in cement morter of
proportion 1: 5 including racking out joints and curing complete as directed
instructure. (protruding rod is to be provided at every 3 course interval and will be
measured and paid separately)
(a) In Sub-structure upto plinth level including dewatering if necessary
(b) In superstructure above plinth level up to 1st floor level.
4.3.2 Extra over item no.4.3.1 (b) above for CC Block work in each subsequent floor or
part thereof above 1st floor level.
4.3.3 200mm thick wall using Cellular Light Weight concrete block of Size
500x200x100mm conforming to IS-2185 Pt-3 or pt-4 in cement morter of
proportion 1: 5 including racking out joints and curing complete as directed in
structure (protruding rod is to be provided at every 3 course interval and will be
(a) In Sub-structure up to plinth level including dewatering if necessary
(b) In Super structure above plinth level upto 1st floor level
4.3.4 Extra over item no.4.3.3 (b) above for CC block work in each subsequent floor or
part thereof above 1st floor level.
4.3.5 100mm thick wall using Cellular Light Weight concrete block of Size
500x200x100mm conforming to IS-2185 Pt-3 or pt-4 in cement mortar of
proportion 1: 5 including racking out joints and curing complete as directed in
super structure above plinth up to 1st floor level (protruding rod is to be provided
at every 3 course interval and will be measured and paid separately)
4.3.6 Extra for CC block walling on item no 4.3.5 for each subsequent floor or part
thereof above the 1st floor level.
Ch-4 : Masonry Work
Page-14
CHAPTER 5: FLOORING AND FLOOR FINISH

Item No.
5.1
5.1.1
Description of works
Unit
Rate
CEMENT CONCRETE FLOORING

Cement concrete works in topping 1:1:2 (1cement :1sand :2 graded aggregates on
R.C.C floor, tread and rise of steps finished with a floating coat of neat cement
using cement slurry for bond @ 2.75 kg.of cement per sq. m. of floor to be laid in
panels including curing complete as directed.
(a) 15 mm thick
Sq.m
Rs.226.67
(b) 20 mm thick
Sq.m
Rs.270.39
5.1.2
25 mm thick cement concrete topping 1:2:4 (1cement : 2 coarse sand : 4 coarse

aggregate of 12 mm nominal size) finished with a floating coat of neat cement
finish to be laid in panels including curing complete as directed.
Sq.m
Rs.225.26
5.1.3
40 mm thick cement concrete floor consisting of 25 mm under layer of cement

concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 12.5 mm
and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2
(1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) finished with a
floating coat of neat cement finish using cement slurry for bond @ 2.75 kg. per
square metre of floor area , wearing layer is to be laid in panels including curing etc.
complete as directed.
concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and
down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement
:1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels and finished
with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg.
per square metre of floor area) including curing etc. complete as directed.
Sq.m
Rs.405.53
Sq.m
Rs.511.10
5.1.5

concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and
down) and 12 mm thick wearing coarse of cement sand plastering in prop. 1:2 laid
in panels and finished with a floating coat of neat cement finish (using cement
slurry for bond @ 2.75 kg. per square metre of floor area) including curing etc.
Sq.m
Rs.510.06
5.1.6
40 mm thick red oxide floor with under layer of 30 mm thick cement concrete in
prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of size 20 mm and down)
and top layer of 10mm thick plaster of cement red-oxide of iron per 50 kg of
cement in prop. 1:3 (1 cement red oxide: 3 coarse sand) finished with a floating
coat of neat cement red oxide mix of same proportion.
Sq.m
Rs.442.09
5.1.7
Providing and laying 50mm thick C.C. floor with metallic concrete hardener topping
under layer of 35 mm thick cement concrete in prop.1:2:4 (1cement : 2 coarse sand
: 4 coarse aggregate of 20 mm and down) and top layer of 15mm thick of metallic
cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate
6 mm and down) by volume with which metallic hardening compound of approved
quality is mixed in the ratio of 4:1 (4 parts of cement : 1 part of metallic floor
hardening compound of approved quality by weight) including finishing with curing
Sq.m
Rs.510.29
5.1.4
Ch-5 : Flooring Floor Finishing Works
Page-15
Item No.
Unit
Rate
5.1.8
Providing and laying 65mm thick C.C. floor with metallic concrete hardener topping
under layer of 50 mm thick cement concrete 1:2:4 (1cement:2 coarse sand:4 coarse
aggregate of 20 mm and down) and top layer of 15mm thick of metallic cement
hardener consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate 6 mm
and down) by volume with which metallic hardening compound of approved
quality is mixed in the ratio of 4:1 (4 parts of cement: 1 part of metallic floor
hardening compound of approved quality by weight) including finishing with curing
Sq.m
Rs.621.47
5.1.9
Providing and fixing glass strips in joints of cement concrete flooring /Terrazo
flooring in all level
(i) 4 mm thick
R.m
Rs.27.88
(ii) 6 mm thick
R.m
Rs.34.22
(i) 4 mm thick
R.m
Rs.35.23
(ii) 6 mm thick
R.m
Rs.45.26
(i) 4 mm thick
R.m
Rs.40.56
(ii) 6 mm thick
R.m
Rs.53.25
(i) 4 mm thick
R.m
Rs.48.20
(ii) 6 mm thick
R.m
Rs.64.71
(a) 15 mm thick
Sq.m
Rs.230.44
(b) 20 mm thick
Sq.m
Rs.265.70
Sq.m
Rs.291.24
Sq.m
Rs.397.19
(a) Any shade or combination of shades using white cement.
Sq.m
Rs.841.63
(b) Any shade or combination of shades using approx. 50% white cement 50% grey
cement.
Sq.m
Rs.825.80
(c) Any shade or combination of shades using grey cement.
Sq.m
Rs.809.97
Extra over item no. 5.2.1 for rubbing and polishing the cement concrete tiles in
flooring, skirting, dado etc.
Sq.m
Rs.142.39
(a) 25 mm wide
(b) 40 mm wide
(c) 50 mm wide
(d) 65 mm wide
5.1.10 Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand)
finished with a floating coat of neat cement including rounding of junctions with
floor.
5.1.11 Red oxide plaster skirting with top layer of 5 mm thick cement plaster of cement
mix using 3.5 kg. red oxide of iron per 50kg of cement in proportion 1:3 (1 cement:
3 coarse sand) finished with a floating coat of cement red oxide mix of same
proportion.
(a) 15 mm thick with under layer of 10 mm thick cement plaster.
(b) 20 mm thick with under layer of 15 mm thick cement plaster.
5.2
5.2.1
5.2.2
5.3
CEMENT CONCRETE TILE FLOORING

Pre-cast cement concrete tiles 20 mm thick with aggregate of sizes up to 6 mm laid
in floors, treads of steps and landing with 20 mm thick bed of cement mortar in
prop. 1:6 (1cement : 6 coarse sand ) joined with neat cement slurry with pigment to
match th
BRICK FLOORING
Page-16
Item No.
Unit
5.3.1
Brick-on-edge floor with 1st class brick and grouted with cement mortar in prop.1:4
(1 cement : 4 sand) including cement pointing in proportion 1:1 (1 cement :1 sand)
finishing and curing complete.
Sq.m
Rs.717.19
5.3.2
Brick-on-flat floor with 1st class brick and grouted with cement mortar in prop. 1:4 (1 cement
: 4 sand) including 15 mm thick cement plastering in proportion 1:2 (1 cement : 2 sand)
finishing with a floating coat of neat cement finish using cement slurry @ 2.75 kg. per sq.
metre of floor area and curing complete.
Sq.m
Rs.672.06
Sq.m
Rs.2,887.70
(a) 38mm thick Hollock wood plank, butt jointed.
Sq.m
Rs.1,886.99
(b) 25mm thick Hollock wood plank, tongue, and groove jointed.
Sq.m
Rs.1,325.78
(c) 25mm thick Hollock wood plank, butt jointed.
Sq.m
Rs.1,287.72
(d) 38mm thick Sal wood plank, butt jointed
Sq.m
Rs.3,465.00
(e) 25 mm thick Sal wood plank, butt jointed.
Sq.m
Rs.2,425.82
Supplying, fitting and fixing 38mm thick (finished size) wooden flooring with sal
wood plank butt jointed, fitted on sal wood joist of size 100mm x 125mm spaced
not more than 900mm apart fitted with 16mm dia bolt and nuts with iron clamp of
50mm x 5mm size inserting in the cement concrete floor base (floor base to be
measured and paid separately) including providing 25mm thick damp proof course
with water proofing compound as recommended by the manufacturer over C.C
floor base including providing kiricide oiling two coats to the timber joists,
underside of the flooring planks, two coats of anti-corrosive paint to the iron
works, including providing ventilation gaps for the timber works of specified size
(75mm x 75mm) covered with welded mesh fabrics at the face of the gap including
dressing, levelling, finishing complete as specified and directed by the department
at all levels (measurement shall be taken at the finished area of the works).
Sq.m
Rs.5,114.32
(a) Pigment of any shade with ordinary cement in top layer only.
Sq.m
Rs.745.38
(b) Pigment of any light shade with white cement in top layer
Sq.m
Rs.758.14
(c) Pigment of any shade with approx. 50% white cement and 50% grey cement in
top layer.
(d) White cement without any pigment on top layer.
Sq.m
Rs.752.88
Sq.m
Rs.738.05
(e) Light shade pigment with ordinary cement on top layer
Sq.m
Rs.729.83
5.4
5.4.1
WOODEN FLOORING
Wooden planking in flooring including fixing to wooden base frame with necessary
wood-screws complete (base of the wooden frame to be measured and paid
separately.)
With 38 mm thick Indian Teak wood plank, tongue and groove jointed.
5.4.2
5.4.3
5.5
5.5.1
Rate
Wooden planking in flooring including fixing to wooden frame with iron screws
complete (base of the wooden frame to be measured and paid separately.)
TERRAZO FLOORING
40 mm thick marble chips flooring rubbed and polished to granolithic finish with
under layer of 32 mm thick cement concrete in prop. 1:2:4 (1 cement:2coarse
sand:4 graded stone aggregate of 10 mm and down graded) and top layer 8 mm
thick with marble chips of any colour or combination of colours and 1 mm to 4 mm
nominal sizes laid in cement marble powder mix 3:1 (3 cement:1marble powder by
weight) in proportion 4:7 (4cement marble powder mix :7 marble chips by volume )
including providing cement slurry including curing etc. complete.
Page-17
Item No.
5.5.2
40 mm thick marble chips flooring rubbed and polished to granolithic finish with under layer
of 30 mm thick cement concrete in prop. 1:2:4 (1 cement: 2 coarse sand:4 graded stone
aggregate of 10 mm and down graded) and top layer 10 mm thick with marble chips of any
colour or combination of colours of required sizes and 1 mm to 4 mm nominal size laid in
cement marble powder mix 3:1 (3 cement:1marble powder by weight) in prop. 4:7 (4cement
marble powder mix :7 marble chips by volume).
5.5.3
5.5.5
5.5.6
5.5.7
Rate
Sq.m
Rs.802.60
Sq.m
Rs.777.69
top layer.
Sq.m
Rs.842.07
Sq.m
Rs.757.60
Sq.m
Sq.m
Sq.m
Rs.808.35
Rs.985.91
Rs.930.11
Sq.m
Rs.871.68
Sq.m
Sq.m
Sq.m
Rs.908.24
Rs.941.63
Rs.920.68
Sq.m
Rs.905.24
Sq.m
Rs.509.92
Sq.m
Rs.596.13
top layer.
Providing and fixing aluminium strips of 40 mm wide and 1.5 mm thick in terrazo
floors in item no. 5.5.1, 5.5.2, 5.5.3 and 5.5.4 .
Extra over item no.5.5.1,5.5.2, 5.5.3 and 5.5.4 for Terrazo floors laid as floor
borders, margins and similar bands in different shade.
Sq.m
Rs.554.05
Sq.m
R.m
Rs.556.39
Rs.65.08
40 mm thick marble chips flooring rubbed and polished to granolithic finish with under layer
of 28 mm thick cement concrete in prop. 1:2:4 (1 cement: 2 coarse sand:4 graded stone
aggregate of 10 mm and down graded) and top layer 12 mm thick with marble chips of any
colour or combination of colours of required sizes 1 mm to 4 mm nominal sizes laid in
cement marble powder mix 3:1 (3 cement : 1 marble powder by weight) in proportion 4:7 (4
cement marble powder mix :7 marble chips by volume).
top layer.
5.5.4
Unit
40 mm thick marble chips flooring rubbed and polished to granolithic finish with
under layer of 25 mm thick cement concrete in prop. 1:2:4 (1 cement: 2 coarse
sand:4 graded stone aggregate of 10 mm and down graded) and top layer 15 mm
thick with marble chips of any colour or combination of colours of required sizes
from 7 mm to 10 mm nominal sizes laid in cement marble powder mix 3:1 (3
cement:1marble powder by weight) in proportion 4:7 (4 cement marble powder
mix :7 marble chips by volume )
top layer.
18 mm thick marble chips skirting or dado rubbed and polish to granolithic finish
with under layer 12 mm thick in cement plaster in prop. 1:3 (1 cement :3 coarse
sand) and top layer 6 mm thick with marble chips of any colour or combination of
colours of 4 mm nominal size laid in cement marble powder mix 3:1( 3 cement : 1
marble powder by weight in proportion of 4:7 (4 cement marble powder mix : 7
marble chips by volume)
Page-18
Item No.
Unit
Rate
(a) Exceeding 75mm but not exceeding 300 mm in width.
Sq.m
Rs.17.43
(b) In narrow band not exceeding 75 mm in width.
Sq.m
Rs.32.97
5.5.8
Extra over item nos. 5.5.1, 5.5.2, 5.5.3 and 5.5.4.for laying Terrazo flooring on stair
case treads including the cost of forming noses.
Sq.m
Rs.23.08
5.5.9
Cutting and cleaning the existing mosaic floor with machine using acid and wax
polishing the same as directed for all levels.
Sq.m
Rs.66.94
Sq.m
Sq.m
Sq.m
Rs.1,242.77
Rs.1,227.06
Rs.1,208.80
(a) Using white cement
Sq.m
Rs.1,267.93
(b) Using 50% white cement and 50% ordinary cement.

(c) Using ordinary cement
Sq.m
Sq.m
Rs.1,252.22
Rs.1,236.51
Sq.m
Rs.1,267.93

Sq.m
Sq.m
Rs.1,252.22
Rs.1,236.51
Sq.m
Rs.1,270.65

Sq.m
Sq.m
Rs.1,227.06
Rs.1,221.17
5.6
5.6.1
TERRAZO TILE FLOORING

Pre-cast Terrazo tiles 20 mm thick with marble chips of sizes up to 6 mm laid in
floors, treads of steps, landing with a bed of 10mm thick cement plaster in
proportion 1:3 (1 cement : 3 coarse sand) jointed with neat white cement slurry
mixed with pigment to match the shade of the tiles including rubbing and
polishing complete.
(a) With precast tiles of any approved shade / shades using white cement.
5.6.2
5.6.3
5.6.4
5.7
5.7.1
Pre-cast Terrazzo tiles 20 mm thick with marble chips of sizes up to 6 mm laid in skirting and
rises of steps with
10mm thick cement plaster in proportion 1:3 (1 cement : 3
coarse sand) jointed with neat white cement slurry including rubbing and polishing
complete. with tiles of any approved shade/shades.
Pre-cast Terrazo tiles 20 mm thick with marble chips of sizes up to 6 mm fixed on walls with
10 mm thick cement plaster in proportion1:3 (1 cement : 3 coarse sand) jointed with neat
white cement slurry including rubbing and polishing complete with tiles of any
approved shade / shades (walls means both exterior and interior walls)
Chequered Terrazo tiles of 22 mm thickness with marble chips of sizes up to 6 mm fixed on

wall with 10 mm thick bed of cement plaster in proportion 1:3 (1 cement : 3 coarse sand)
jointed with neat white cement slurry mixed with pigment to match the shades of tiles
including rubbing and polishing complete with tiles of any approved shade/shades.
TILES WORKS
CERAMIC TILES
A) ON FLOOR
Page-19
Item No.
Unit
Rate
5.7.1.1 Providing Ceramic Tiles of approved quality, size, shape and thickness not less than
8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm
thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary
finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White
cement slurry mixed with approved pigment to match the shade of granite slab,
complete at all levels as specified and directed (coloured pigment should be in
conformity with colour of slab and as approved and directed by the Department).
a)
Normal range
Somany/ Orient/Nitco /Asian Make
i)
Of size 300mmx300mm and above
Sq.m
Rs.680.00
ii)
Sq.m
Rs.720.00
b)
Executive range
Somany/ Orient/Nitco/Asian Make
i)
Sq.m
Rs.750.00
ii)
Of size 400x400 mm and above
Sq.m
Rs.760.00
c)
Delux range
Somany/ Orient/Nitco/Qutone Make
i)
Sq.m
Rs.970.00
ii)
Sq.m
Rs.980.00
iii)
Sq.m
Rs.990.00
i) Of size 200mmx200mm and above
Sq.m
Rs.694.00
ii) Of size 200mmx300mm and above
Sq.m
Rs.640.00
Sq.m
Rs.715.00
Sq.m
Rs.855.00
iii) Of size 148.5mmx450mm and above
Sq.m
Rs.870.00
Sq.m
Rs.924.33
Sq.m
Rs.931.53
iii) Of size 250mmx500mm and above
Sq.m
Rs.1,894.44
iv) Of size 300mmx600mm and above
Sq.m
Rs.1,545.91
v) Of size 300mmx900mm and above
Sq.m
Rs.2,217.81
B) ON WALLS
5.7.1.2 Providing polished ceramic wall tiles of approved quality, size, shape and
thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm
thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary
finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white
cement slurry mixed with approved pigment to match shade of tiles complete at all
levels as specified and directed. (Cement plastering to be measured and paid
separately). (Coloured pigment should be in conformity with colour of tiles and as
approved and directed by the Department). (Walls means both interior and exterior
walls).
a) Normal range
b) Executive range
c) Delux range
Somany/ Orient/Nitco/Varmora Make
5.7.2 VITRIFIED TILES
Page-20
Item No.
Unit
Rate
Sq.m
Rs.1,712.50
Sq.m
Rs.1,483.13
Sq.m
Rs.1,525.18
Sq.m
Rs.2,116.23
Sq.m
Rs.2,399.00
Sq.m
Rs.1,311.67
ii) Of size150mmx605mm and above (Strips)
Sq.m
Rs.1,902.79
iii) Of size300mmx600mm and above
Sq.m
Rs.1,630.64
iv) Of size300mmx900mm and above
Sq.m
Rs.2,626.68
i). Well, Chocolate, Diamond Square, Ramp, Beach Sand (300x300) mm
Sq.m
Rs.884.47
ii). Old Castle (455x455) mm
Sq.m
Rs.1,023.33
iii). Banana (370x140) mm
Sq.m
Rs.982.19
A) ON FLOOR
5.7.2.1 Providing VITRIFIED floor tiles of approved quality of specified size, shape and
thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15
mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including
cutting where necessary finished with flush pointing with Fix-A-Tile
(Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment
to match shade of tiles, mixed with approved pigment to match the shade of the
tiles, complete at all levels as specified and directed. (Coloured pigment should be
in conformity with colour of tiles and as approved and directed by the Department)
a) Normal range
Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make
b) Executive range
c) Delux range
B) ON WALLS
5.7.2.2 Providing polished vitrified wall tiles of approved quality, size, shape and thickness
not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in
prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished
with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement
slurry mixed with approved pigment to match shade of tilesc complete at all levels
as specified and directed. (coloured pigment should be in conformity with colour of
tiles and as approved and directed by the department).
5.7.3
CONCRETE TILES
(A) FLOOR TILES
5.7.3.1
Providing polished SUNROCK-Hi CTS/ MULTIWYN tiles of approved quality, size,

shape and thickness not less than 18mm on floors and skirtings over cement
mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting
where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika /
Pedelite / Rouf) /white cement slurry mixed with approved pigment to match
shade of tiles complete at all levels as specified and directed. (Coloured pigment
should be in conformity with colour of tiles and as approved and directed by the
Department).
(a) SUNROCKHi CTS TILES
Page-21
Item No.
Unit
Rate
Legato, Ribbera, Matrix, Esquire, Enigma, Flora, Little Flora, Nirvana, Purl,
Contoura, Cobble, Canaletta, Nexus, Koral
Sq.m
Rs.1,045.19
5.7.3.2 Providing Transporating to site,laying,fitting and fixing at all levels tiles for
following purpose of SUNROCK-Hi-CTS tiles of high density cement concrete
designer coloured tiles made of 100% pure white cement tested as per IS-12371980 of approved quality,size shape of thickness 5mm to 50mm to be ancored by
adhesive cement and copper wire anchoring including cutting where necessary
finished with flush pointing with polymer modified cementations tile joint filler of
"ROOF RAINBOW TILE MATE-140" white cement slurry mixed with approved
pigment to match shade of tiles complete as specified and directed.(Coloured
pigment should be in conformity with color of tiles and as approved and directed
by the department. (Cloud, Wave, Old Rock, English Stone)
Sq.m
Rs.1,119.77
Providing polished MULTIWYN tiles of approved quality, size, shape and thickness
not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in
prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished
with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement
slurry mixed with approved pigment to match shade of tiles complete at all levels
as specified and directed. (Cement plastering to be measured and paid separately).
(Coloured pigment should be in conformity with colour of tiles and as approved and
directed by the Department). (Walls means both interior and exterior walls).
(Willow, Brick, Marvel, Sigma, Enamora, Pyramid, Crocotile, Bricket, Denver)
Sq.m
Rs.1,045.19
(a) Silicon (Pavers) 60 mm thick
Sq.m
Rs.1,258.63
(b) Silicon (Pavers) 50 mm thick
Sq.m
Rs.1,119.77
(c) Silicon (Pavers) 40 mm thick
Sq.m
Rs.982.19
Sq.m
Rs.1,045.19
i) Ivory (300x300) mm
Sq.m
Rs.773.90
ii) Grey, Terracotta, Green (300x300) mm
Sq.m
Rs.843.33
iii) Jesalmer (300x300) mm
Sq.m
Rs.871.62
Sq.m
Rs.1,131.64
(b) MULTIWYN TILES
(B) WALL TILES
5.7.3.3
(C) PAVERS
5.7.3.4 Providing polished tiles of approved quality, size, shape of specified thickness on
pavers over a base of 100mm compacted sand gravel including cutting where
necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite /
Rouf) /white cement slurry mixed with approved pigment to match shade of tiles
complete at all levels as specified and directed. (Coloured pigment should be in
conformity with colour of tiles and as approved and directed by the Department).
(A) SUN ROCK HIGH CTS Tiles (Pavers)
(B) MULTIWYN Tiles (Pavers)

Patella, West wind, Harringbone, Flexi, Super
(C) VITA Tiles (Pavers)
5.8
5.8.1
KOTA STONE SLAB / SAND STONE FLOORING

Kota-stone slab flooring of 18 mm thick over 20mm thick base of cement plaster
1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed
with pigment to match the shade of the slab including rubbing and polishing
complete.
(1) 550mm x 550mm
Page-22
Item No.
Unit
Rate
Sq.m
Rs.1,374.76
(1) 550mm x 550mm
Sq.m
Rs.1,128.55
(2) 600mm x 900mm and above
Sq.m
Rs.1,387.12
(i) 25 mm thick
Sq.m
Rs.1,316.48
(ii) 40 mm thick
Sq.m
Rs.2,218.72
Extra for nosing in steps of red or white, fine dressed and rubbed with sand stone.
R.m
Rs.145.85
(i) Dungri slab
Sq.m
Rs.3,960.89
(i) Marwat Slab
Sq.m
Rs.1,891.07
(III) Kumari Slab
Sq.m
Rs.1,540.12
(IV) Rajnagar Slab
Sq.m
Rs.1,610.84
(i) Dungri slab
Sq.m
Rs.1,438.70
(ii) Marwat Marble
Sq.m
Rs.1,323.95
(iii) Kumari Marble
Sq.m
Rs.1,066.40
(iv) Rajnagar Marble
Sq.m
Rs.1,151.81
(i) Dungri slab
Sq.m
Rs.1,251.89
(ii) Marwat Marble
Sq.m
Rs.1,109.10
(iii) Kumari Marble
Sq.m
Rs.964.99
Sq.m
Rs.1,023.70
(c) With 18mm thick marble stone tiles of size 300mm x 300mm
(i) Dungri slab
Sq.m
Rs.1,181.16
(ii) Marwat Marble
Sq.m
Rs.1,037.05
(iii) Kumari Marble
Sq.m
Rs.936.96
(2) 600mm x 900mm and above

5.8.2
5.8.3
Kota stone slab of 18 mm thick in riser of steps, skirting, dado and pillars laid with
10mm thick cement plaster 1:3 (1 cement : 3 coarse sand) and jointed with
grey cement slurry mixed with pigment to match the shade of the slabs including
rubbing and polishing complete.
Fine dressed and rubbed stone slab flooring over 18 mm thick base of cement
mortar 1:5 (1cement : 5 coarse sand) with joints 3 mm wide, sides buttered with
cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigments to match the
shade of stone and pointing with the same mortar.
Red sand stone
5.8.4
5.9
5.9.1
5.9.2
MARBLE FLOORING
18 mm thick Marble stone slab flooring of sizes 1200x1200 including treads and
risers of steps, skirting, laid over 20 mm thick base of cement plaster 1:6 (1 cement
: 6 coarse sand) laid and jointed with grey cement slurry including rubbing and
polishing complete with marble slab of specified quality and shade at all levels.
18 mm thick marble stone tiles in flooring including risers and treads of steps,
skirting, dado, walls, pillars laid with 10 mm thick base of cement plaster in
prop.1:3 ( I cement : 3 coarse sand) and jointed with grey cement slurry including
rubbing and polishing complete with marble tiles of specified quality and shade at
all levels.
(a) With 18mm thick marble stone tiles of size 600mm x 600 mm
(b) With 18mm thick marble stone tiles of size 600mm x 450 mm, 600mm x 300mm
Page-23
Item No.
Unit
Rate
Sq.m
Rs.966.32
18 mm thick Makrana white marble stone tiles of size 600mm x 450mm in flooring
including risers and treads of steps, skirting, nosing of treads, dado, walls, pillars
laid with 10 mm thick base of cement plaster in prop.1:3 ( I cement : 3 coarse sand)
and jointed with grey cement slurry including rubbing and polishing complete with
marble tiles of specified quality and shade at all levels.(For using Makrana slab,
prior permission should be taken from The Chief Engineer, PWD(Bldg.) and rate
should be approved before use)
5.9.4. Extra for Granite finish in marble slab / tiles at all levels.
5.10 GRANITE FLOORING
5.10.1 Providing polished granite tiles of approved quality, size and shape and thickness
not less than 8mm, on walls over 15mm thick, cement mortar bed in prop. 1:3 (1
cement : 3 coarse sand) including cutting where necessary, finished with flush
pointing on wall with ordinary cement slurry mixed with approved pigment to
match shade of tiles, complete at all levels as specified and directed.
Sq.m
Rs.3,334.91
Sq.m
Rs.227.69
Sq.m
Rs.1,157.36
5.10.2 Providing 18mm thick Granite slab on vertical face of pedestal laid over 10 mm
thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) jointed with
grey cement slurry mixed with pigment to match the shade of the slab including
rubbing and polishing complete as directed with approved quality of shade.
Sq.m
Rs.2,443.02
(i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)
Sq.m
Rs.2,261.22
(ii) With White cement
Sq.m
Rs.2,229.16
Sq.m
Rs.1,150.26
Sq.m
Rs.1,168.92
5.9.3.
5.10.3 Providing polished granite tiles of approved quality, size, shape and thickness not
less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick
base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting
where
necessary
finished
with
flush
pointing
with
Fix-A-Tile
(Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment
to match shade of tiles, mixed with approved pigment to match the shade of the
tiles, complete at all levels as specified and directed. (Cement plastering to be
measured and paid separately). (Coloured pigment should be in conformity with
colour of tiles and as approved and directed by the Department)
5.10.4 Providing polished granite tiles of approved quality, size, shape and thickness not
less than 8mm on walls and skirtings over cement mortar bed 15 mm thick in prop.
1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with
flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry
mixed with approved pigment to match shade of tiles complete at all levels as
specified and directed. (Cement plastering to be measured and paid separately).
(Coloured pigment should be in conformity with colour of tiles and as approved and
directed by the Department). (Walls means both interior and exterior walls).
5.10.5 Providing polished granite slab of approved quality, size, shape and thickness not
less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar
bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where
necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf)
/white cement slurry mixed with approved pigment to match the shade of granite
slab, complete at all levels as specified and directed. (Cement plastering to be
measured and paid separately). (Coloured pigment should be in conformity with
colour of slab and as approved and directed by the Department).
Page-24
Item No.
Unit
Rate
Sq.m
Rs.2,246.07
Sq.m
Rs.2,228.58
Sq.m
Rs.2,661.63
Sq.m
Rs.2,644.14
Sq.m
Rs.3,350.38
Sq.m
Rs.3,332.89
Sq.m
Rs.695.47
Sq.m
Rs.660.75
a) Deluxe -VC
Sq.m
Rs.1,015.62
b) Deluxe -Rotto VC
Sq.m
Rs.1,015.62
a). Premium
Sq.m
Rs.968.05
b). Deluxe
Sq.m
Rs.984.76
Sq.m
Rs.1,700.93
a). Imperia Series- Gres Tiles
Sq.m
Rs.1,230.34
b). Imperia Series- Gres Lepato (1), Gres Lepato (2), Gres Lepato + Full Body
Sq.m
Rs.1,286.92
c). Tuscan Series- Gres Lepato
Sq.m
Rs.1,493.92
d). Tuscan Series- Gres Tiles
Sq.m
Rs.1,313.92
e). PVT- Hi Polish- PGVT
Sq.m
Rs.1,604.50
Sq.m
Rs.1,419.35
(i) Normal Quality
(i) Executive Quality
(iii) Deluxe Quality
5.11
5.11.1
ANTISKID TILES
Providing Antiskid Tiles of approved quality size, shape not less than 8mm on
floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse
sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white
cement complete at all level as specified and directed.
(A) CERAMIC
i)Normal range (Sizes 300 mm x 300mm and above)
(a)Orient made: Galaxy Brown, Galaxy creama, Galaxy Pink, Galaxy Green, Pulsar
Beige, Pulsar Blue, Pulsar Dove, Pulsar Pink, Burj Brown, Burj Green, Burj Slate
ii)Executive range-1 (Sizes 400 mm x 400mm and above)
(a) Somany made- VC Shield (Group- 25) (406x406) mm Deluxe -VC
iii)Executive range-2 (Sizes 600 mm x 600mm and above)
Somany made- VC Shield (Group- 25) (605x605) mm
5.11.2
VITRIFIED
i)Normal range (Sizes 300 mm x 300mm and above)
Somany made- Durastone (Unpolished heavy duty Vitrified Tiles)
ii)Executive range-1 (Sizes 600 mm x 300mm and above)

a) Nitco made (Oak Wood)
iii)Executive range-2 (Sizes 600 mm x600mm and above)
i) Nitco made
ii) Somany made- Duragres (Glazed Vitrified Tiles) (605x605) mm

a). Gress Matt
Page-25
Item No.
Unit
Rate
b). Gress Stone
Sq.m
Rs.1,544.07
c). Gress VC Shield
Sq.m
Rs.1,544.07
i) Melody Brand
Sq.m
Rs.1,286.00
ii) Aspire Brand
Sq.m
Rs.1,149.70
iii) Flute/Rainbow Brand
Sq.m
Rs.1,190.46
iv) Sonata/Splendour Brand
Sq.m
Rs.1,489.80
v) Trump Brand
Sq.m
Rs.1,717.80
vi) Harmony Brand
Sq.m
Rs.1,762.38
vii) Galaxy Brand
Sq.m
Rs.1,601.89
viii) New Royal Guard Brand
Sq.m
Rs.1,543.30
viii) Trump (Grey) Brand
Sq.m
Rs.1,035.06
ix) Basic Brand
Sq.m
Rs.726.81
ix) Piano Brand
Sq.m
Rs.1,068.18
i) SNM-102
Sq.m
Rs.1,495.48
ii) SNM-152
Sq.m
Rs.1,738.77
i) Lawn 66(18)
Sq.m
Rs.3,044.38
ii) Field 12
Sq.m
Rs.2,801.09
iii) Lawn 66(29)
Sq.m
Rs.3,644.32
iii) HT PA 13nd
Sq.m
Rs.4,896.43
Sq.m
Rs.8,824.86
ii) Merbau/Jatoba/Cherry Brand
Sq.m
Rs.8,047.47
iii) Oak Brand
Sq.m
Rs.6,755.60
WOODEN LAMINATED FLOORING/ENGINEERED WOOD FLOORING/CARPET

TILES/LOOP PILE CARPETS/DECORATIVE GRASS/LANDSCAPING TURF
5.12.1 Providing,fitting and fixing Loop pile carpet from Uniproducts (India) Ltd.of
thickness not less than 4mm with maximum 7mm pile height with pile fibre of
100% BCF polypropelene of width 3.66m laid on existing concrete floor with
approved transparent polythene and foam sheet to make the floor surface even
and sound free complete as directed and specified
5.12
5.12.2 Providing,fitting and fixing Synthetic Decorative Grass/Landscaping Turf of width

4.00m from Uniproducts (India) Ltd.of thickness not less than 10mm laid on
existing concrete floor complete as directed and specified.
(A) Decorative Grass from Uniproducts(India) Ltd.
(B) Landscaping Turf from Uniproducts(India) Ltd.
5.12.3 Providing,fitting and fixing wooden flooring from Uniproducts (India) Ltd.of
thickness 14mm made of pure wood(Engineered Wood) of different types with a
top layer of 3mm thick hard wood and Under layer of 2mm thickness made of
polythene and foamsheet laid on existing concrete floor complete as directed and
specified
Engineered Wood (New) from Uniproducts(India) Ltd.
i) Walnut Brand
5.12.4 Providing,fitting and fixing Laminated abrasion resistant wooden flooring from
Uniproducts (India) Ltd.of thickness not less than 8.2mml laid on existing concrete
floor with underlayer of approved transparent polythene and foam sheet to make
the floor surface even and sound free complete as directed and specified
Laminate Floorings-A from Uniproducts(India) Ltd.
Page-26
Item No.
Unit
Rate
i) Unitex AC3 Brand
Sq.m
Rs.1,562.40
ii) Unitex AC4 Brand
Sq.m
Rs.1,576.10
i) Ultimate Brand
Sq.m
Rs.1,962.94
ii) Essential Plus Brand
Sq.m
Rs.1,403.76
iii) Coral Brand
Sq.m
Rs.1,247.39
iv) Tetris/Firkin Brand
Sq.m
Rs.2,636.76
v) Junction Brand
Sq.m
Rs.2,327.23
vi) Highway Brand
Sq.m
Rs.2,080.12
vii) Insight Brand
Sq.m
Rs.2,226.61
viii) Zebra/Hendriki/Tristis/Kuda Brand
Sq.m
Rs.1,947.65
ix) Pearl/Sapphire Brand
Sq.m
Rs.1,675.07
5.12.5 Providing,fitting and fixing Carpet tiles of size 500x500mm with thickness not less
than 4mm made of 100% Olefin Polypropleyne material,with dual backing; Primary
backing with PVC and Secondary with Reinforced Fibre glass from Uniproducts
(India) Ltd.laid on existing concrete floor complete as directed and specified
Carpet Tiles from Uniproducts(India) Ltd.
x) Ural Brand
xi) Runway Brand
Rs.3,513.11
Sq.m
Rs.3,015.07
Page-27
CH - 6: PLASTERING AND HERITAGE FINISHES

Item
Description
No.
6
PLASTERING
6.1 LIME PLASTERING
6.1.1 15 mm thick lime plaster 1:1:1 (1 lime: 1 surkhi:1 sand) in single coat on fair side of
brick/concrete walls for interior plastering up to second floor level including arises,
internal round angles, chamfers and / or rounded angles not exceeding 80mm girth
and finished even and smooth including curing complete as directed.
Unit
Rate
Sqm
Rs. 160.86
6.1.2 15 mm thick lime plaster 1:1:1 (1 lime: 1 surkhi:1 sand) in single on half brick walls
for interior plastering up to second floor level including arises, internal rounded
angles,chamfers and/or rounded angles not exceeding 80mm girth and finished
even and smooth including curing complete as directed.
Sqm
Rs. 165.63
6.1.3 Extra over item no. 6.1.1 and 6.1.2 for each subsequent floor or part thereof
beyound 2nd floor level.
Sqm
Rs. 15.31
6.2
CEMENT PLASTERING
6.2.1 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for
interior plastering up to 1st floor level including arises or rounded angles not
exceeding 80mm girth and finished even and smooth including curing complete as
directed.
a) In cement mortar 1:3
Sqm
Rs. 128.16
b) In cement mortar 1:4
Sqm
Rs. 116.85
c) In cement mortar 1:5
Sqm
Rs. 107.87
d) In cement mortar 1:6
Sqm
Rs. 101.88
Sqm
Rs. 167.05
Sqm
Rs. 147.23
Sqm
Rs. 136.63
Sqm
Rs. 127.87
B) On fair side
Sqm
Rs. 165.52
Sqm
Rs. 145.70
Sqm
Rs. 135.09
Sqm
Rs. 126.34
Sqm
Rs. 210.14
Sqm
Rs. 183.86
Sqm
Rs. 169.57
Sqm
Rs. 157.59
6.2.2 15 mm thick Cement plaster in single coat on single or half brick wall for interior
plastering up to 1st floor level including arises, internal rounded angles, not
exceeding 80mm girth and finished even and smooth including curing complete as
directed.
A) On rough side
6.2.3 20 mm thick Cement plaster in two coats on single or half brick walls for interior
plastering up to 1st floor level including arises, internal rounded angles,chamfers
and / or rounded angles not exceeding 80mm in girth and finished even and
smooth including curing complete as directed.
A) On rough side (backing coat 15 mm and finishing coat 5mm thick)
B) On fair side (backing coat 10 mm and finishing coat 10mm thick)
Ch-6 : Plastering Haritage Works
Page-28
Item
No.
Description
Unit
Rate
Sqm
Rs. 243.74
Sqm
Rs. 217.46
Sqm
Rs. 203.17
Sqm
Rs. 191.19
Sqm
Rs. 6.93
Sqm
Rs. 5.15
Sqm
Rs. 4.21
Sqm
Rs. 3.42
Sqm
Rs. 10.39
Sqm
Rs. 7.75
Sqm
Rs. 6.31
Sqm
Rs. 5.11
Sqm
Rs. 13.89
Sqm
Rs. 10.35
Sqm
Rs. 8.45
Sqm
Rs. 6.80
Sqm
Rs. 21.78
a) On Single coat plaster
Sqm
Rs. 3.87
b) On two coat plaster
Sqm
Rs. 4.64
Sqm
Rs. 3.83
Sqm
Rs. 4.98
Sqm
Rs. 3.53
Sqm
Rs. 4.41
a) Flush band
Sqm
Rs. 251.73
b) Sunk band
Sqm
Rs. 267.09
6.2.4 Extra over item no 6.2.1 to 6.2.3 for providing and mixing water proofing materials
in cement mortar in prop as recommended by the manufacturer including curing
i) 10 mm thick plaster
ii) 15 mm thick plaster
ii) 20 mm thick plaster
6.2.5 Extra over item no 6.2.1 to 6.2.3 for plastering on celling and soffits of stairs up to
1st floor level (instead of plastering on walls) including curing complete as directed.
6.2.6 Extra over item no 6.2.1to 6.2.3 for interior plastering above 1st floor level for
every addl floor or part thereof including curing complete as directed.
6.2.7 Extra over item no 6.2.1 to 6.2.3 for exterior plastering over wall up to a height of
1st floor level above ground level including curing complete as directed.
6.2.8 Extra over item no 6.2.1 to 6.2.3 for exterior plastering over wall for every addl
floor or part thereof beyond 1st floor level including curing complete as directed.
6.2.9 15 mm thick plain cement mortar bands in cement mortar 1:4 in width including
A) Up to 300 mm width
Page-29
Item
No.
Description
Unit
Rate
Sqm
Rs. 292.64
a) Flush band
Sqm
Rs. 190.37
b) Sunk band
Sqm
Rs. 205.71
c) Raised band
Sqm
Rs. 231.28
a) Flush pointing
Sqm
Rs. 74.85
b) Ruled pointing
Sqm
Rs. 77.41
c) Cut or weather struck pointing
Sqm
Rs. 77.41
c) Raised and Cut pointing
Sqm
Rs. 119.34
a) Flush pointing
Sqm
Rs. 71.49
b) Ruled pointing
Sqm
Rs. 73.98
c) Cut or weather struck pointing
Sqm
Rs. 73.98
d) Raised and Cut pointing
Sqm
Rs. 115.92
a) Flush pointing
Sqm
Rs. 55.19
b) Ruled pointing
Sqm
Rs. 58.26
a) Flush pointing
Sqm
Rs. 52.33
b) Ruled pointing
Sqm
Rs. 55.39
a) Flush pointing
Sqm
Rs. 49.93
b) Ruled pointing
Sqm
Rs. 53.00
a) Flush pointing
Sqm
Rs. 48.64
b) Ruled pointing
Sqm
Rs. 51.71
a) Flush pointing
Sqm
Rs. 73.54
b) Ruled pointing
Sqm
Rs. 76.09
a) Flush pointing
Sqm
Rs. 68.84
b) Ruled pointing
Sqm
Rs. 71.39
c) Raised band
B) Above 300 mm width
6.3
Pointing
6.3.1 Pointing on brick work with cement mortar including curing complete as
directed.(Measurement shall be taken on surface area of the wall).
A) Cement mortar prop. 1:3
B) Cement mortar prop. 1:4
6.3.2 Pointing on brick flooring with cement mortar including curing complete as
directed.(Measurement shall be taken on surface area of the floor).
A) On flat brick flooring
i) Cement mortar prop. 1:2
ii) Cement mortar prop. 1:3
iii) Cement mortar prop. 1:4
iv) Cement mortar prop. 1:5
B) On edge brick flooring

Page-30
Item
No.
Description
Unit
Rate
iii) Cement mortar prop. 1:4

a) Flush pointing
Sqm
Rs. 65.24
b) Ruled pointing
Sqm
Rs. 67.80
a) Flush pointing
Sqm
Rs. 63.30
b) Ruled pointing
Sqm
Rs. 65.86
a) Flush pointing
Sqm
Rs. 80.21
b) Ruled pointing
Sqm
Rs. 83.28
Sqm
Rs. 134.42
a) Flush pointing
Sqm
Rs. 77.44
b) Ruled pointing
Sqm
Rs. 80.51
Sqm
Rs. 131.65
a) Flush pointing
Sqm
Rs. 75.61
b) Ruled pointing
Sqm
Rs. 78.16
Sqm
Rs. 124.19
a) Flush pointing
Sqm
Rs. 72.84
b) Ruled pointing
Sqm
Rs. 75.40
Sqm
Rs. 121.43
Sqm
Rs. 211.99
(a) Granules (Code : HGR)
Sqm
Rs. 484.30
(b) Granules with Top Coat (Code : HGRT)
Sqm
Rs. 546.93
c) Fine Granules (Code : FG)
Sqm
Rs. 337.98
(d) Fine Granules with top coat (Code : FGHT)
Sqm
Rs. 483.16
(e) Flakes (Code : HFR)
Sqm
Rs. 568.72
(f) Flakes with Top coat (Code : HFRT)
Sqm
Rs. 651.31
(g) Fine Flakes (Code : FFH)
Sqm
Rs. 496.67
(h) Fine Flakes with Top coat (Code : FFHT)
Sqm
Rs. 650.66
iv) Cement mortar prop. 1:5
6.3.3 Pointing on stone masonry with cement mortar including including curing
complete as directed.(Measurement shall be taken on surface area of the wall)
A) On random rubble uncoursed stone masonry
B) On squre, rubble coursed or uncoursed stone masonry

6.3.4 Raised and cut pointing on Ashler masonry or concrete block walling in white
cement mortar 1:3 (1 white cement : 3 marble dust) including curing complete as
directed. (Measurementshall be taken on surface area of the wall)
6.4 HERITAGE FINISHING
6.4.1 Supplying and laying of permanent wall finish for interior and exterior walls with
surface coating of Heritage Surface Texture of Bakelite Hylam Limited for all types
of buildings at all levels as specified and directed by the department.
Page-31
Item
No.
Description
Unit
Rate
(i) Granite Finish (Code : HFG)
Sqm
Rs. 813.54
(j) Sand Dune
Sqm
Rs. 273.69
(k) Silica Duke
Sqm
Rs. 111.84
(l) Lineal Finish
Sqm
Rs. 322.73
(m) Roto Finish
Sqm
Rs. 302.91
(n) Roller Coat (Application by Special Roller)
Sqm
Rs. 231.37
(o) Roller Coat (Application by brush)
Sqm
Rs. 106.03
(p) Spray Coat (Bubble Finish)
Sqm
Rs. 382.85
(q) Spray Coat (Compact Finish)
Sqm
Rs. 698.69
Page-32
Ch 7: CEILLING, LINING AND PARTITION

Item
No.
7.1
Unit
Rate
WATTLE/ SPILT BAMBOO CEILING
7.1.1 Providing wattle /spilt bamboo ceilling mud plastered on top and 15mm cement
plaster in proportion 1:4 in two coats -10 mm first coat and 5mm second coat on
bottom, white wash three coats on cement plastered surface complete (timber
ceilling joists to be measured and paid separately).
Sqm
183.83
7.1.2 Providing wattle/ spilt bamboo ceilling 15mm cement plastered in proportion 1:10
on top and hessian cloth at bottom fitted with 38mmx12mm 1st class hollock /
bonsum / sundi timber beading chamfered and finished with 2 coats of enamel
painting to the timber beads complete (timber ceilling joists to be measured and
paid separately).
7.1.3 Providing wattle/spilt bamboo ceilling 15mm cement plastered at top in proportion
1:10 and markin cloth at bottom fitted with 38mm x12mm 1st class hollock/
bonsum/ sundi timber beading chamfered and finished with 2 coats of chalk
washing to the markin cloth and 2 coats of enamel painting to timber beads
complete (timber ceilling joists to be measured and paid separately).
Sqm
211.87
Sqm
215.83
7.1.4 Providing wattle/ spilt bamboo crete ceilling with 25 mm thick mud plaster on top
and bottom in two coats - 15mm and 10mm, the final coat being trowel finished
and white wash 3 coats below.( ceilling joists to be measured and paid separately).
Sqm
166.5
7.1.5 Providing single layer bamboo-mat ceilling with lattice-pattern jaffri or mesh size
40mmx 40mm made out of bamboo slips of size 5mmx2mm size at bottom stiffened
with bamboo slip of 25 mm x 5 mm size. (ceilling joist to be measured and paid
separately).
7.1.6 Repairing and refixing tarja mat ceiling.
Sqm
161.08
Sqm
38.77
7.1.7 Taking out and refixing dharamat ceiling after repairing as necessary including
changing damage kamies, dhara, jaffri works, bethua bamboo ceiling joints, as and
where necessary, including cleaning the top and bottom faces of the ceiling as
directed complete,including tying with galvd wire for fixing in proper position.
Sqm
39.34
7.2
GYPBOARD CEILING
7.2.1 Supplying, fitting, fixing and painting where necessary (one coat primer and two
coats of paint) M/F Suspended Ceiling which includes G.I. perimeter channels of size
0.55mm thick (having one flange of 20mm and another flange of 30mm and a web
of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with
the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I.
intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm
each) from the soffit at 1220mm c/c with ceiling angle of width
25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion
fasteners.
Ch-7: Ceilling,Lining Partitions Works
Page-33
Item
No.
Unit
Rate
Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal
flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate
channel with the help of connecting clip and in direction perpendicular to the
intermediate channel at 457mm c/c, 9.5mm/ 12.5mm tapered edge Gypboard
(conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long
drywall screws at 230mm c/c. Screw fixing is done mechanically either with screw
driver or drilling machine with suitable attachment. Finally, the boards are to be
jointed and finished so as to have a flush look which includes filling and finishing the
tapered and square edges of the boards with jointing compound, joint paper tape
and two coats of drywall topcoat suitable for Gypboard complete at all levels as
specified and directed. (For light fittings, providing opening for doors, window,
ventilators etc, cut out made with frame of perimeter channel supported suitably to
be measured and paid separately where necessary).
(i)
9.5mm thick
Sqm
1214.8
(ii)
12.5mm thick
Sqm
1105.5
coats of paint) suspended ceiling which includes G.I. perimeter channels of size
fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and
two equal flanges of 26mm each with lips of 10.5mm are then fixed to the
intermediate channel with the help of connecting clip and in direction perpendicular
to the intermediate channel at 298mm c/c.
Then 12.5mm thick square edge Fulltone/ Sundance/ Cratone/ Louvertone/
Textured. Gypboard panels of size 595mmx595mm (conforming to IS:2095-1982) is
then screw fixed to ceiling section with 25mm long drywall screws at 290mm c/c.
Screw fixing is done mechanically either with screw driver or drilling machine with
suitable attachment. Finally, the boards are to be jointed and finished so as to have
a flush look which includes filling and finishing the tapered and square edges of the
boards with jointing compound, joint paper tape and two coats of drywall topcoat
suitable for Gypboard complete at all levels as specified and directed. (For light
fittings, grill diffusers etc. cut out to be made with the frame of perimeter channel
supported suitably and measured and paid separately as and where necessary).
(Glass wool to be measured and paid separately).
(A)
M/F Frame Work with Design Type Textured Gypboard Tiles 9.5mm thick.
Sqm
1453
(B)
M/F Frame Work with Design Type Semi Perforated Gypboard (Sundance) Tiles (NRC
value 0.20 with 50mm glass wool mat backing) 12.5mm thick.
Sqm
1462.8
(C)
M/F Frame Work with Acoustic Type Fissured Gypboard (Cratone) Tiles (NRC value
0.57 with 50mm glass wool mat backing) 12.5mm thick.
Sqm
1679.4
(D)
M/F Frame Work with Acoustic Type Fully Perforated Gypboard (Fulltone) Tiles (NRC
value 0.75 with 50mm glass wool mat backing) 12.5mm thick.
Sqm
1661
(E)
M/F Frame Work with Acoustic Type Slit Gypboard (Louvertone) Tiles (NRC value
0.72 with 50mm glass wool mat backing) 12.5mm thick.
Sqm
1684.5
Page-34
Item
No.
coats of paint) pre-coated G.I. angle size 24mmx24mmx80mm thick fixed to the
brick wall/ partition at the perimeter of ceiling with nylon sleeves and screws, at
610mm c/c. Then suspending main 'T' section (bottom pre-coated) size
24mmx38mmx0.70mm and 3600mm long from the soffit in one direction with the
help of metal Rawl Plug. Soffit cleat and G.I. Rod 4mm diameter with galvanised
level clip 1220mm c/c G.I. cross
Unit
Rate
Sqm
(A)
BPB Grid ceiling system with plain Gypboard Tiles 12.5mm thick.
Sqm
1294.7
(B)
BPB Grid ceiling system with plain Gypboard Tiles 9.5mm thick.
Sqm
1286.8
(C)
BPB Grid ceiling system with plain Gypboard Tiles 8.0 mm thick.
Sqm
1270.6
(D)
BPB Grid ceiling system with P.V.C. laminated plain Gypboard (Polyshield-P) Tiles
9.5mm thick.
Sqm
1599.2
(E)
BPB Grid ceiling system with P.V.C. laminated crack Gypboard (Polyshield-C) Tiles
9.5mm thick.
Sqm
1608.5
(F)
BPB Grid ceiling system with Design Type Textured Gypboard Tiles 9.5mm thick.
Sqm
1389.9
(G)
BPB Grid ceiling system with Design Wall Paper Gypboard (Paprex Panel) Tiles
Sqm
(i)
8 mm thick
Sqm
1487.6
(ii)
(H)
9.5mm thick
BPB Grid ceiling system with Fabric Based Sound absorb Panel (595mmx595mm).
Sqm
1453.6
Sqm
2115.1
BPB Grid ceiling system with Design Type Semi Perforated Gypboard (Sundance)
Tiles
coats of paint) wall lining which includes 12.5mm/ 9.5mm thick Gypboard
(conforming to IS:2095-1982) screw fixed to the Ceiling section of size 0.55mm thick
having a knurled web of 51.5mm and two equal flanges of 26mm each with lips of
10.5mm made of G.I. Steel placed at 600mm c/c in perimeter channels of size
0.55mm thick having one flange of 20mm and flane of 30mm and a web of 27mm
made of G.I. Steel fixed to the floor & ceiling with nylon sleeves & wood screws at
600mm c/c.
Sqm
1399.7
Supplying, fitting, fixing and painting where necessary (one coat primer and two
coats of paint) wall lining which includes 12.5mm/ 9.5mm thick Finally the boards
are to be jointed and finished so as to have a Flush look which includes filling and
finishing with jointing Compound, joint paper tape, two coat drywall top coat
suitable for Gypboard complete as specified and directed at all levels (Glass wool to
be measured and paid separately) (For light finishing, skirting providing opening for
doors, windows, ventilators etc. cut out made with the frame of perimeter channel
supported suitably to be measured and paid suitably when necessary).
Sqm
(A)
M/F wall lining with plain Gypboard 9.5mm thick.
Sqm
1224.5
(B)
M/F wall lining with plain Gypboard 12.5mm thick.
Sqm
1218.2
(I)
coats of paint) wall lining which includes 12.5mm thick Louvertone/ Sundance/
Cratone/ Fulltone (slit) Gypboard ceiling panels of size 595mmx595mm (conforming
to IS:2095-1982) screw fixed to the Ceiling section of size 0.55mm thick having a
knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm
made of G.I. Steel placed at 298mm c/c in perimeter channels of size 0.55mm thick
having one flange of 20mm and flane of 30mm and a web of 27mm made of G.I.
Steel fixed to the floor & ceiling with nylon sleeves & wood screws at 600mm c/c.
Sqm
Page-35
Item
No.
Finally the boards are to be jointed and finished so as to have a Flush look which
includes filling and finishing with jointing Compound, joint paper tape, two coat
drywall top coat suitable for Gypboard complete as specified and directed at all
levels (Glass wool to be measured and paid separately) (For light finishing, skirting
providing opening for doors, windows, ventilators etc. cut out made with the frame
of perimeter channel supported suitably to be measured and paid suitably when
necessary).
(A) M/F wall lining with Design Type Semi Perforated (Sundance) Gypboard 12.5mm
thick (NRC value=0.20 with 50mm glass wool mat backing).
(B) M/F wall lining with Acoustic Type Fissured (Cratone) Gypboard 12.5mm thick (NRC
value=0.57 with 50mm glass wool mat backing).
(C) M/F wall lining with Acoustic Type Fully Perforated (Fulltone) Gypboard 12.5mm
thick (NRC value=0.75 with 50mm glass wool mat backing).
(D) M/F wall lining with Acoustic Type Slit (Louvertone) Gypboard 12.5mm thick (NRC
value=0.72 with 50mm glass wool mat backing).
coats of paint) 97mm thick metal stud partition (Single layer) including one layer of
tapered edge 12.5mm thick Gypboard (conforming to IS:2095-1982) screw fixed to
drywall screw of 25mm at 300mm c/c to either side of 75mm studs (0.55mm thick
having one flange of 34mm and another flange of 36mm made of G.I. steel) with
joints staggered to avoid leakage through joints and jointing the square and tapered
edges of the boards and finishing so as to have a flush look which includes filling and
finishing with jointing Compound, joint paper tape, two coat drywall top coat
suitable for Gypboard complete as specified and directed at all levels (Glass wool to
be measured and paid separately) (For light finishing, skirting providing opening for
doors, windows, ventilators etc. cut out made with the frame of perimeter channel
supported suitably to be measured and paid suitably when necessary).
Unit
Rate
Sqm
1332.8
Sqm
1569
Sqm
1549
Sqm
1574.6
(A)
Partition with Plain Gypboard
Sqm
2006.6
(B)
Partition with Acoustic Type Fissured (Cratone) Gypboard (NRC value=0.57 with
50mm glass wool mat backing)
Sqm
2442
(C)
Partition with Acoustic Type Fully Perforated (Fulltone) Gypboard (NRC value=0.75
with 50mm glass wool mat backing)
Sqm
2876.7
(D)
Partition with Acoustic Type Slit (Lovertone) Gypboard (NRC value=0.72 with 50mm
glass wool mat backing)
Sqm
3170.7
coats of paint) M/ F suspended ceiling which includes G.I. perimeter channels of size
to the intermediate channel at 457mm c/c, 9.5mm/ 12.5mm Gypboard. False ceiling
(Light Duty) with Metal Polyster Laminated Board on Back (MPL) (conforming to
IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screws
at 230mm c/c. Screw fixing
Sqm
Page-36
Item
No.
Unit
Sqm
(i)
is done mechanically either with screw driver or drilling machine with suitable
attachment. Finally, the boards are to be jointed and finished so as to have a flush
look which includes filling and finishing the tapered and square edges of the boards
with jointing compound, joint paper tape and two coats of drywall topcoat suitable
for Gypboard complete at all levels as specified and directed. (For light fittings,
providing opening for doors, window, ventilators etc., cut out made with frame of
perimeter channel supported suitably to be measured and paid separately as and
where necessary).
9.5mm MPL
Sqm
1487.6
(ii)
12.5mm MPL
Sqm
1502.7
coats of paint) M/ F suspended ceiling which includes G.I. perimeter channels of size
to the intermediate channel at 457mm c/c, 9.5mm/ 12.5mm thick Gypboard.
Rate
Sqm
False ceiling (Light Duty) with Moisture Resistant Board (conforming to IS:20951982) is then screw fixed to ceiling section with 25mm long drywall screws at
230mm c/c. Screw fixing is done mechanically either with screw driver or drilling
machine with suitable attachment. Finally, the boards are to be jointed and finished
so as to have a flush look which includes filling and finishing the tapered and square
edges of the boards with jointing compound, joint paper tape and two coats of
drywall topcoat suitable for Gypboard complete at all levels as specified and
directed. (For light fittings, providing opening for doors, window, ventilators etc.,
cut out made with frame of perimeter channel supported suitably to be measured
and paid separately as and where necessary).
(i)
9.5mm MRB
(ii) 12.5mm MRB

coats of paint) 50mm floor & ceiling channels (with flanges of 32mm each and
0.55mm thick) with the help of nylon sleeves and steel screws to the floor and R.C.C.
respectively. 48mm studs (with flanges of 36mm and 34mm and 0.55mm thick) are
then placed at every 595mm c/c in between floor and ceiling channels. The studs
are then anchored to the wall at every 600mm c/c with help of L cleats fixed to
studs with nut and bolts and to the wall with metal rawl plugs. Then 15mm thick
Gypboard Silt Tone Sound Smart panels having 3mm thick non woven carpet (plain)
are then fixed to the studs with a suitable beading. 50mm thick glass wool shall be
placed at the back side of the panels to get the required absorption. (For skirting
light fittings, grills diffusers etc. cut out to be made with the frame of perimeter
channels supported suitably and measured and paid separately as and when
necessary). (Glass wool to be measured and paid separately).
Sq.m.
1427
Sqm
1457.6
Sqm
2762.3
Sqm
507.7
7.2.10 Extra for providing Twiga Insul glass wool mat backing with chicken mesh cover of
Twiga Fibre Glass insulation as specified and directed at all levels.
(i)
25mm thick
Page-37
Item
No.
Unit
Rate
(ii) 50mm thick

7.2.11 Extra for providing cut outs for light/ A.C. diffusers, drops, access panel etc. in
Gypboard ceiling portion, partition wall, lining etc. complete at all levels as specified
and directed.(net area of cut out portion to be measured and paid only).
Sq.m.
702.2
Sq.m.
605
7.2.12 Extra for providing two coats of water resistant sealant to upper surface of the
board to prevent it from damage due to water leakage complete at all levels as
specified and directed.
Sqm
44
coats of paint) moulded timber skirting with best quality 1st class local wood timber
planks of 75mm height and 20mm thick at bottom of Gypboard partition and wall
lining etc. complete as specified and directed at all levels.
Sqm
1016.4
(a). Teak wood plank (20mm thick)
Sqm
1457.72
(b).Hollock (25mm thick)
Sqm
1157.48
(c) Bonsum / Sundi wood plank (25mm thick)
Sqm
1130.19
(d).Gamari timber plank (25mm thick)
Sqm
1157.48
(a).Hollock (25mm thick)
Sqm
1330.44
(b) Bonsum/ Sundi timber plank (25mm thick)
Sqm
1320.13
(c).Gamari timber plank (25mm thick)
Sqm
1320.13
(d).2nd class timber plank (25mm thick)
Sqm
1073.92
(a). Teak ( 40mmx12mm).
Rm
59.08
(b) Hollock timber plank (40mmx12mm)
Rm
46.49
7.3 WOODEN WORK IN CEILING AND WALLS

7.3.1 Providing and fixing wood plank ceiling with tongued and grooved joint leaving a
gap of 10 mm as per drawing including necessary nails & wood screws
complete(Timber frame work to be measured and paid separately).
7.3.2 Providing and fixing wood plank ceiling with butt and lap joints including necessary
nails and wood screws complete (Timber frame work to be measured and paid
separately).
7.3.3 Providing and fixing plain, squre edged cover fillet in ceiling and lining with wood
screws including mitreing at junctions.
(c) Extra for making chamfered edges of cover fillets.

7.3.4 Providing, fitting and fixing frame work for wall panelling with Hollock/ Bonsum/
Sundi battens of size 50mmx25mm fixed over tapering plugs made out of
trapezoidal section having base 50mmx50mm at the bottom and 38mmx38mm at
the top with depth of 50mm embeded in cement sand mortar in prop1:3 and spaced
450mm to 500mm apart complete with counter sunk wood screw of 50mm length.
Rm
12.37
Sqm
357.22
Sqm
Sqm
Sqm
1296.76
1867.51
2240.63
7.3.5 Providing and fixing Teak wood lining with tongue and groove joint leaving a gap
of 10mm as per drawing including fitting and fixing with countersunk screws
with the frame work complete (frame work to be measured and paid separately).
I).12 mm thick.
ii).20 mm thick.
iii).25 mm thick.
7.3.6 Providing and fixing 1st class local wood Hollock / Bonsum / Sundi / Gamari lining
with tongue and groove joints leaving a gap of 10mm as per drawing including
fitting and fixing with countersunk screws with the frame work complete (frame
work will be measured and paid separately).
i).12 mm thick.
Page-38
Item
No.
a) Hollock
b) Gamari
ii).20 mm thick.
a) Hollock
b) Gamari
iii).25 mm thick.
a) Hollock
b) Gamari
7.3.7 Providing and fixing 1st class local wood Hollock /Bonsum/ Gamari/ Sundi lining
with butt joints including fitting and fixing with countersunk screws with the frame
with complete (frame work to be measured and paid separately).
Unit
Rate
Sqm
Sqm
1050.15
1050.15
Sqm
Sqm
1420.63
1420.35
Sqm
Sqm
1653.55
1653.55
a) Hollock
Sqm
800.62
b) Bonsum / Sundi
Sqm
798.29
c) Gamari
Sqm
798.29
a) Hollock
Sqm
1121.27
b) Bonsum / Sundi
Sqm
1121.27
b) Gamari
Sqm
1121.27
a) Hollock
Sqm
1324.16
b) Bonsum / Sundi
Sqm
1318.33
b) Gamari
Sqm
1318.33
i).12 mm thick
Sqm
908.85
ii).20 mm thick
Sqm
1438.21
iii).25 mm thick
Sqm
1776.35
i).12 mm thick
Sqm
702.45
ii).20 mm thick
Sqm
1023.1
iii).25 mm thick
Sqm
1220.15
i).12 mm thick
Sqm
702.45
ii).20 mm thick
Sqm
1023.1
iii).25 mm thick Hollock
Sqm
1225.98
i).12 mm thick.
ii).20 mm thick.
iii).25 mm thick.
7.3.8 Providing and fixing timber skirting with butt joining and screws (frame work and
cover fillets to be measured and paid separately).
a)Teak wood / Sisu wood.
b)Gamari timber plank
c) Hollock/Bonsum/Sundi
7.4
CEILING TILES
Page-39
Item
No.
7.4.1 Supplying, fitting and fixing ceiling tiles of 10mm thick made from Duratuff medium
density fibre board in size 1200mm x 1200mm x 10mm with Sal wood timber frame
(to be measured and paid separately)leaving an expansion gap of 3mm with
necessary nails, screws etc. including 1st class local wood (Hollock /Bonsum / Sundi
etc.)beading of size 50mm x 12mm complete as directed and specified.
7.5
Unit
Rate
Sqm
321.08
Sqm
Sqm
786.2
995.66
I) 10mm thick Bison Panel
Sqm
1012.05
ii) 12mm thick Bison Panel
Sqm
1178.58
iii) 16mm thick Bison Panel
Sqm
1292.52
iv) 20mm thick Bison Panel
Sqm
1362.42
I) .10mm thick Bison panel
Sqm
1297.47
ii) .12mm thick Bison panel
Sqm
1328.25
iii) .16mm thick Bison panel
Sqm
1397.88
i)10mm thick Bison Panel
Sqm
1271.28
ii)12mm thick Bison Panel
Sqm
1299.35
iii)16mm thick Bison Panel
Sqm
1383.83
Sqm
1360.44
Sqm
1372.01
BISON PANEL CELING AND PARTION
7.5.1 Providing, fitting and fixing in position false ceiling of 6mm thick Bison panel
(cement bonded particle board) on timber frame of 1st class local wood (Hollock/
Bonsum/ Sundi) of 50mm x 50mm spaced at not more than 1.20m apart , fixed to
the wall at the end with necessary nails, wood screws, hooks,bolts etc. including
painting (one coat primer and two coats of painting) as necessary complete as
directed by the Department for all levels.
(a) Both sides commercial
(b) One side laminated
7.5.2 Providing, fitting and fixing in position Bison panel (cement bonded particle board)
partition wall on one face of the timber frame of 1st class local wood (Hollock/
Bonsum/ Sundi)of 50mm x 80mm spaced at not more than 1.20m apart , fixed with
necessary nails, wood screws, bolts etc. including painting (one coat primer and two
coats painting) as necessary complete as directed by the Department for floors.
(A) Both sides commercial
(B) One side laminated and one side commercial
(C) Both side laminated
7.5.3 Providing, fitting and fixing in position 6mm thick Bison panel (cement bonded
particle board) partition wall on both faces of the timber frame of 1st class local
wood (Hollock/ Bonsum/ Sundi) with horizontal and vertical batten of size 50mm x
80mm spaced at not more than 1.20m apart , with necessary nails, wood screws,
bolts etc. including painting (one coat primer and two coats painting) as necessary
complete as directed by the Department for all levels.
(a) Both sides commercial
(b) One side laminated
7.6
PLYWOOD / HARDBOARD PARTION
7.6.1 Providing, fitting and fixing in position plywood / hardboard partion walls with 6mm
thick plyboard / hardboard (best) with horizontal and vertical Sal battens of size
50mm x 80mm spaced at not more than 1.20m apart with necessary nails, wood
screws, bolts etc. complete as directed by the Department for all levels (Painting /
Varnishing to be measured and paid separately).
Page-40
Item
No.
Unit
Rate
A) 6mm thick Plyboard

a) On one face of the frame
Sqm
951.13
b) On both faces of the frame
Sqm
1455.22
a) On one face of the frame
Sqm
596.91
b) On both faces of the frame
Sqm
767.02
7.7.1 Providing, fitting and fixing in position ceiling tiles of Natural Fibre Thermosets
Composite of jute, polymer and chemicals of Durosam brand or equivalent as
directed by department in size 610mm x 610mm x 4mm thick with necessary nails,
screws etc. complete as specified and directed at all levels (Framework to be
measured and paid seperately.)
7.8 Pre laminated Particle Board
Sqm
1623.3
7.8.1 Providing, fitting and fixing in position 62mm thick double skin partion with well
seasoned Bonsum/ Sundi / Hollock frame in size 75mm x 38mm and internal frame
of 50mm x 38mm and fixing on both sides 9mm thick flat pressed melamine faced
pre-laminated graded wood patrticle boards bonded with phenol formaldehyde
synthetic resin of approved shade as specified and directed at all levels.
One side decorative
(Bhutan board/Nepal Board/Bajaj board or equivalent board as directed by
departement)
Sqm
3812.63
7.8.2 Providing, fitting and fixing in position 62mm thick double skin partion with well
seasoned Sal/ Bonsum/ Sundi / Hollock frame in size 75mm x 38mm and internal
frame of 50mm x 38mm and fixing on both sides 8mm thick flat pressed melamine
faced pre-laminated baggage board medium density fibre boards (MDF) bonded
with phenol formaldehyde synthetic resin of approved shade as specified and
directed at all levels.
a) With Bajaj - exterior grade(one side decorative)
(i) 8 mm tgick
7.8.3 Providing, fitting and fixing in position 38/30mm thick single skin partion with well
seasoned Bonsun/ Sundi / Hollock frame in size 75mm x 38mm / 75mm x 50mm and
fixing 12mm / 18mm thick flat pressed melamine faced pre-laminated graded wood
patrticle boards bonded with phenol formaldehyde synthetic resin of approved
shade as specified and directed at all levels.
Sqm
4440.87
Sqm
Sqm
1386.84
1695.41
Sqm
Sqm
1519.28
1792.48
Sqm
Sqm
Sqm
184.95
231.26
262.13
B) 6mm thick Hardboard
7.7
DUROSAM CEILING TILES
(I) Exterior grade - One side decorative

(a) 12mm thick
(b) 19mm thick
(II) Exterior grade - Both side decorative
(a) 12mm thick
(b) 19mm thick
7.9 OTHER TYPES OF CEILING
7.9.1 Providing, fitting and fixing hard board sheet ceilling with approved quality with
necessary nails, wood screws including 1st class local wood 50mm x 12mm (
hollock/ bonsum/ sundi ) beading including paining two coats to timber beads
complete as directed ( ceilling joist to be measured and paid separately ).
(a). 3 mm thick
(b). 4.5 mm thick
(c). 6 mm thick
Page-41
Item
No.
7.9.2 Providing, fitting and fixing in position ceiling tiles of unveneered teakwood particle
board bonded with phenol formaldehyde synthetic resin equivalent to anchor nova
teak super in size 600 mm x 600mmx12mm leaving an expansion gap of 10m m as
per the drawing with necessary links and wood screws complete (timber frame
work to be measured and paid separately).
(a). Plain
Unit
Rate
Sqm
615.72
Sqm
622.09
Sqm
628.46
Sqm
799.7
(b). Curved surface
Sqm
936.96
(c).Extra for sunk or raised mouldings in plaster of paris (Gypsum, anhydrous) ceiling
Sqm
336.05
(a). 15mm thick
Sqm
319.64
(b). 20mm thick
Sqm
340.66
(c). 25mm thick
Sqm
368.68
i).12 mm thick.
Sqm
1465.22
ii).20 mm thick.
Sqm
1694.5
iii).25 mm thick.
Sqm
2016.76
i).12 mm thick.
Sqm
1188.27
ii).20 mm thick.
Sqm
1493.97
iii).25 mm thick.
Sqm
1672.3
i).12 mm thick.
Sqm
1061.97
ii).20 mm thick.
Sqm
1367.67
iii).25 mm thick.
Sqm
1546
(b). Half perforated/ Full perforated

7.9.3 Providing, fitting and fixing in position ceiling tiles of Insulex board(soft) in size
600mm x 600mm x 12mm leaving an expansion gap of 10mm as per the drawing
with necessary nails and wood screws complete (timber frame work to be measured
and paid separately).
7.9.4 Providing 10mm thick plaster of paris (Gypsum, Anhydrous) ceiling up to a height of
5m above floor level over 1st class Hollock / Bonsum / Sundi wood strips 25mm x
6mm with 10mm gap in between with rabit wire mesh fixed to wooden frame
(frame work to be measured and paid separately).
(a). Flat surface
7.9.5 Providing and fixing expanded polystyrene plain tiles (thermocol) ceiling with fevicol
@ 5 lits.per 10 m2 and brass screws etc.complete ( frame work and cover fillets to
be measured and paid separately).
7.9.6 Providing and fixing decorative type veneered particle board lining with butt joint
leaving a gap of 10mm as per drawing including fitting and fixing with countersunk
screws with the frame work (frame work and cover fillets to be measured and paid
separately).
(A) Decorative
(B) One Side Decorative
7.9.7 Providing and fixing one side teak veneered particle board lining with butt joint
leaving a gap of 10mm as per drawing including fitting and fixing with countersunk
screws with the frame work complete as specified and directed at all levels(frame
work to be measured and paid separately).
7.10 Ceiling with Exposed Metal (G.I.) Frame work with E-Grid - 2430
Page-42
Item
No.
Unit
Rate
7.10.1 Providing and fixing, in position suspended false ceiling using E-Grid (exposed
ceiling suspension 2430 system) of grid size 600mm x 600mm/1200mmx600mm
with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm .
Using 4mm/6mm thick High Pressure Steam Cured Non Asbestos Fibre Cement
Board as per IS 14862, to be placed in a grid of G.I. system duly suspended with
4mm/6mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin
from the roof with adjustment clip providing positions for light fixtures, air
conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners
to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last
hanger at the end of each main runner should not be placed at more than 450mm
from the adjacent wall. Flush fitting 1220mm cross tee to be interlocked between
main runners @ 610mm c/c, so as to form 600mm x 600mm/1200mmx600mm grid,
all complete as per the drawing & directions of engineer-in-charge.
Finally, if specified, boards are to be painted with 2 coats of acrylic emulsion paint of
approved shade/make over a coat of cement primer before installing it on the grid.
(A) Standard Ceilings of Everest make or equivalent as directed by the departement
(i) Using 4 mm thick FC Board
Sqm
786.38
(ii) Using 6 mm thick FC Board
Sqm
907.12
(B) Designer Ceilings of Everest make or equivalent as directed by the departement

(i) Using 4 mm thick FC Board
Sqm
906.69
(ii) Using 6 mm thick FC Board
Sqm
1079.86
A) Everest Designer Ceilings or equivalent as directed by the departement

(Primered)
A) Using 13mm thick ceiling tiles
Sqm
1235.05
B) Using 15mm thick ceiling tiles
Sqm
1753.07
7.11 ACOUSTICAL APPLICATION

7.11.1 Providing and fixing Mineral Fiber Acoustic Ceiling Tiles in 600mm x 600mm of
13mm/15mm thickness to be placed in E- Grid Suspended Ceiling Grid 2430 System
consisting of Main Runner 3600 mm long, Cross Tee 1200mm/600mm long and Wall
Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the
wall by steel screws with distance 300 mm c/c. Main Runner shall be placed along
the shorter dimension of the area to be covered. The distance between the two
Main Runners to be maintained at 1200mm. The Cross Tee 1200mm will be inserted
in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a
modular grid of 1200mm x 600mm. Additional Cross Tees of 600 mm shall be placed
perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x
600mm.E-Grid of module size 600mm x 600mm shall be supported by 4/6 mm dia
G.I. wire from purlins/soffit Mineral Fiber Acoustic Ceiling Tiles of Everest Industries
Limited should be placed in the E-Grid module to form a False Ceiling including the
cuttings complete as directed.
7.12 FIBRE CEMENT BOARD WALL PANELLING
Page-43
Item
No.
Unit
Rate
7.12.1 Providing and fixing in position concealed G.I. sections for paneling using High
Pressure Steam Cured), pre-primered, self-embossed, designer cement board or the
non-primered, plain Fibre cement boards of 6mm thickness confirming IS 148622000 fixed on the supporting "W' profile (0.55mm thick) having a knurled web of
51.5mm and two flanges of 26mm each with lips of 10.55mm ) placed @600mm c/c
vertically and 11200mm c/c horizontally in perimetre channel (having one flange of
20mm and another flange of 30mm with thickness of 0.55mm and web of length
27mm).Perimetre channel is fixed on the floor and the ceiling with the nylon sleeves
@ 300mm c/c with expandable fasteners. Board is fixed to the "W" profile with
25mm long self embedding type Fibre cement Screws @ 300mm c/c, all complete
as per the drawing & directions of Engineer-in -charge. The boards may be finished
so as to have a uniform gap/groove or Flush finish.The flush finish should be done
with Elasto prefab joint sealant. Internal Jointing Compound and paper tape as per
the procedure laid down by company.
Note: Alternatively, the uniform gap/groove may be covered with decorative
molding or may be finished with Jointing filler including 2 coats of acrylic emulsion
paint of approved shade/make, over a coat of cement primer before installing it on
the grid as required.
I) Everest Plain FC board or equivalent
Sqm
1088.53
II) Everest Designer FC board or equivalent
Sqm
1241.71
III) Everest HDFC Board or equivalent
Sqm
1182.85
i) Using 8mm thick FC Wall board of Everest make or equivalent
Sqm
1731.53
ii) Using 10 mm thick FC Wall board of Everest make or equivalent
Sqm
1943.08
iii) Using 12 mm thick FC Wall board of Everest make or equivalent
Sqm
2154.31
i) Using 9mm thick FC Wall board of Everest make or equivalent
Sqm
2123.99
ii) Using 12 mm thick FC Wall board of Everest make or equivalent
Sqm
2537.1
7.12.2 Providing and fixing double skinned partitions using G.I. sections High Pressure
Steam Cured non asbestos Fibre Cement wall board conforming to IS 14862-2000 ,
fixed on frame work using 25mm fully threaded self embedding type Fibre Cement
Screws @300mm c/c on either side of Steel G.I. 51mm studs (0.55mm thick having
one flange of 40mm and another flange of 42mm ) placed at 600mm c/c in 51mm
floor and ceiling channel (0.55mm thick having equal flange of 32mm G.I. steel)
with joints staggered to avoid through joints, all complete as per the drawing &
direction of Engineer-in -Charge.
The boards may be finished so as to have a uniform gap/groove or Flush finish.The
flush finish should be done with Elasto prefab joint sealant. Everest Internal Jointing
Compound and paper tape as per the procedure laid down by the company.
Alternatively, the uniform gap/groove may be covered with decorative molding or
may be finished with Jointing filler.
Finally, if specified the boards to be painted with 2 coats of acrylic emulsion paint of
approved shade/make, over a coat of cement primer before installing it on the grid.
A. For Dry Area
B. For Wet Area
Page-44
Item
No.
Unit
Rate
7.12.3 Providing and fixing 50mm/ 75mm thick Non asbestos Everest Solid Wall Panels
(Fibre reinforced aerated cement core sandwich panels) made out of light weight
fibre reinforced aerated cement/concrete core composed of port land cement,
flyash, binders etc., and 4mm thick Non asbestos fibre cement Boards (Everest Wall
Boards) as per IS 14862:2000 on either side of the core, having a tongue and groove
on longitudinal side of the modules. These Everest Solid Wall Panels are erected /
installed using galvanised iron steel tracks of 1mm thick & of size 15x50x25mm as
bottom track, 38x50x38mm as top track used for fixing to the floor and top of the
wall respectively. Finally grooves of the panels should be finished with Everest
recommended jointing compound.
i) Using 50 mm thick SW panel of Everest make or equivalent
Sqm
2255.57
i) Using 75 mm thick SW panel of Everest make or equivalent
Sqm
2578.06
i) Using 9mm thick board of Everest make or equivalent
Sqm
1475.35
ii) Using 12mm thick board of Everest make or equivalent
Sqm
1681.9
7.12.4 Providing and fixing in position High Pressure Steam Cured Non Asbestos Fibre
Cement Everest Heavy Duty Wall Board (Density>1500 Kg/m3) confirming IS 14862
& Type A as Eves Board to be fixed on iron or timberSection as per the drawing &
directions of engineer-in-charge. Finally, if specified, the boards are to be painted
with 2 coats of acrylic emulsion paint of approved shade/make over a coat of
cement primer after installing it on to the concealed metal framework.
Page-45
CH-8 : ROOFING & ROOF TREATMENT

Item
Description
No
8.1 ROOFING
8.1.1 Providing corrugated galvenised Iron sheet roofing of TATA SHAKTEE / SAIL
including fitting and fixing necessary galvenised J or L hooks, bolts and nuts 8 mm
dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer
complete excluding cost of roof truss, purlin etc. (Roof trusses and purlin etc.to be
measured and paid separately).
Unit
Rate
(a) 0.45 mm thick
Sqm
450.45
(b) 0.50 mm thick
Sqm
484.76
(c) 0.55 mm thick
Sqm
512.95
(d) 0.60 mm thick
Sqm
550.94
Sqm
576.68
(i) 150 mm lapping
RM
134.92
(ii) 230 mm lapping
RM
152.69
(i) 150 mm lapping
RM
143.63
(ii) 230 mm lapping
RM
162.86
(i) 150 mm lapping
RM
150.84
(ii) 230 mm lapping
RM
171.27
(i) 150 mm lapping
RM
169.59
(ii) 230 mm lapping
RM
193.14
RM
176.08
RM
200.71
(e) 0.63 mm thick

8.1.2 Providing galvd iron ridging of TATA SHAKTEE / SAIL including supplying and fixing
necessary galvd screws/washers etc. complete as directed.
(a) 0.45 mm thick
(b) 0.50 mm thick
(c) 0.55 mm thick
(d) 0.60 mm thick
(e) 0.63 mm thick

(i) 150 mm lapping
(ii) 230 mm lapping
8.1.3 Labour for fitting and fixing Galvd corrugated iron roofing including supplying and
fixing with new galvd screw, J hook, bolts nuts, washer etc. complete as directed.
Sqm
120.72
8.1.4 Labour for taking out and refitting Galvd ridging including supplying and fixing
necessary galvd screw, bolts and nuts complete as directed.
8.1.5 Providing 13 mm mesh hexagonal wire net made of one I.S. designation (1mm dia)
wire above post plate in eaves with 1st class Hollock/Bonsum/ Sundi timber frame
to fit exactly with the corrugation of roofing sheet including kiricide oiling two
coats to timber works complete as directed.
8.1.6 Providing 13 mm mesh hexagonal wire net made of one I.S. designation (1mm dia)
wire above post plate in eaves with 1st class (Hollock/Bonsum) timber frame to fit
exactly with the corrugation of roofing sheet including painting two coats with
approved paint to timber works complete as directed.
8.1.7 Providing 0.63 mm thick(24 gauge) galvd plain sheet in valley , lining, flashing etc.
and fitted with gavd. Iron J or L hook bolts and nuts, G.I. limpet and bitumen
washer complete, bent to shape and fixed in a positions as directed.
Ch-8: Roofing and Roof Treatment
RM
66.7
Sqm
519.36
Sqm
543.57
Sqm
427.61
Page-46
Item
Description
No
8.1.8 Supplying, fitting and fixing wind ties with 40mm x6mm M.S. flat iron and necessary
10 mm dia G.I hook bolt, G.I flat washer and bitumen washer etc. complete
including two coats painting with red oxide anticorrosive paint.
Unit
Rate
RM
201.58
8.1.9 Labour for taking out and refitting M.S. flat wind ties in position with new 10 mm
dia J hook, G.I. flat washer, bitumen washer etc. including painting one coat with
red oxide paint complete.
RM
8.1.10 Providing bracket made out of M.S. flat, bent to proper size and shape as per
drawing and fitting with necessary bolts, nuts, sand washers etc. for fixing A.C / G.I.
sheet gutters with purlins.
kg
63.54
208.03
8.1.11 Providing thatch roofing with sun grass (Ullo) in layer of 75 mm thick with half spilt
bamboo fillet and tying with galvd. wire complete.
(a) 75 mm thick.
Sqm
277.14
(b) 150 mm thick.
Sqm
531.14
8.1.12 Providing and laying thatching, capping to ridge and hip with new sun grass of 75
mm thick (fine work) stiffened with bamboo slips of size 30mm x 6mm and tied
with galvd. tying wire complete.
RM
186.27
8.1.13 Re-thatching with new sun grass including dismantling and removing old thatching
and also defective bamboo and replacing with new one and stacking the old thatch
at safe place.
(a) 75 mm thick.
Sqm
288.52
(b) 150 mm thick.
Sqm
558.65
8.1.14 Over thatching 75 mm thick with new sun grass, filling in holes and gaps in the roof
etc.
Sqm
2819.04
8.1.15 Providing and laying bamboo slip jaffri of meshes not exceeding 63mm x 38mm
including tying to the purlins and rafters with cane slip or galvd. tying wire.
(a) Fine work
Sqm
51.59
(b) Rough work
Sq.m
Sqm
42.07
104.91
RM
34.49
RM
24.97
8.1.16 Providing single layer of bamboo mat lining over roof frame.
8.1.17 Providing bamboo maruli ties, purlins, rafters including tying with cane sling /
Galvd. tying wire.
(a) With Bhaluka bamboo.
(b) With Jati bamboo.
8.1.18 Providing bamboo roof truss with whole ruas bam boo and kamis, ruas placed at
150 mm apart and kamis 200mm to 230mm apart including tying all members with
galvd tying wire.
Sqm
8.1.19 Providing bamboo jaffri over thatch roof with 200mm sq mesh bamboo slips of
35mm width
Sqm
8.1.20 Providing whole bamboo roof frame with old and new materials, new materials
being at least 25% of the total required.
Sqm
8.1.21 Providing bamboo roof frame with kami of size 30mm x 6mm.
116.29
33.52
34.93
Sqm
42.07
Page-47
Item
Description
No
8.1.22 Renewing / providing 5 layer of bamboo single roofing with matured muli bamboo
tarja, woven closely round tiers of single kamis spaced 150mm apart on ground
with 600mm and 900 mm single seperately. First 900mm long tiers are tied at
lower ends of roof frames projected 450mm, towards the eves, 750mm tiers tied
with 150mm overlap of first tiers, 3 nos 600 mm tiers tied with 150mm overlap of
second tiers, 2 nos 600mm tiers tied with 150mm overlap of third tiers and forth
600mm tiers continued up to ahead of ridge, the last but one will be 750mm and
the last one will be 600mm long (this section gives 5 layers) Then with 900mm wire,
diagonally woven double bamboo tarja mat over the ridge complete with all tying
with galvd wire as directed and specified.
Unit
Rate
Sqm
738.25
8.1.23 Providing corrugated 1.20 mm thick transparent fibre sheet roofing including fitting
and fixing necessary galvanised J or L hooks, bolts and nuts of 8 mm dia with
bitumen washer 25 mm dia. X 3 mm thick and 1.6 mm thick limpet washer
complete excluding cost of roof truss, purlins etc. (Roof trusses, purlin, etc. to be
Sqm
1319.67
8.1.24 Providing 1.2mm thick transparent fibre sheet ridging including supplying and fixing
necessary galvanised screws / washers etc. complete as specified and directed.
(a) 1.20 mm thick - 150 mm lapping
244.22
(b) 1.20 mm thick - 300 mm lapping
280.66
Sqm
1134.15
Sqm
1417.55
(a) 1.20 mm thick - 150 mm lapping
RM
247.19
(b) 1.20 mm thick - 300 mm lapping
RM
283.63
(a) 0.50 mm thick
Sqm
462.17
(b) 0.55 mm thick
Sqm
499.33
(c) 0.60 mm thick
Sqm
537.37
(d) 0.65 mm thick
Sqm
575.41
(i) 150 mm lapping
RM
408.71
(ii) 230 mm lapping
RM
472.56
8.1.25 Providing coloured corrugated transparent fibre sheet roofing including fitting and
fixing necessary galvanised J or L hooks, bolts and nuts of 8 mm dia. with bitumen
washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete
excluding cost of roof truss, purlins etc. (Roof trusses, purlins etc. to be measured
and paid separately)
(a)1.00 mm thick
(b)1.20 mm thick
8.1.26 Providing coloured transparent fibre sheet ridging including supplying and fixing
necessary galvanised screws / washer etc. complete as specified and directed.
8.1.27 Providing Iron Plastic Laminated corrugated coloured sheet Roofing at all levels
including fitting and fixing galvanised J or L hooks, bolts and nuts of 8 mm diameter
with Bitumen washer 35 mm x 35 mm x 3 mm and G.I. Diamond washer 40 mm x
40 mm x 3 mm complete excluding cost of roof truss, purlins etc. (Roof trusses,
Purlins etc. to be measured and paid separately).
8.1.28 Providing Colour Coated (Iron Plastic Laminated Sheet) Ridging including supplying
and fixing necessary galvanised screws / washer etc. complete as specified and
directed.
(A) 0.50 mm thick
Page-48
Item
No
Description
Unit
Rate
(B) 0.55 mm thick

(i) 150 mm lapping
RM
446.76
(ii) 230 mm lapping
RM
516.95
(i) 150 mm lapping
RM
486.12
(ii) 230 mm lapping
RM
562.88
(i) 150 mm lapping
RM
524.17
(ii) 230 mm lapping
RM
607.27
(a) 0.40mm thick
Sqm
556.18
(b) 0.50mm thick
Sqm
734.15
(C) 0.60 mm thick
(D) 0.65 mm thick
8.1.29 Providing circular corrugated / trouhed Everlast Aluminium roofing sheet of

Aluminium Alloy procured from primary aluminium producer (On submission of
certificate of alloy purchasing from primary producer) including fitting and fixing
necessary J or L hooks bolts and nuts 8 mm dia with bitumen / EPDM washer 25mm
dia x 3mm thick and 1.6mm limplet washer complete excluding cost of truss, purlin
etc.
Everlast/ Paragon make or equivalent Quality as directed by the departement
8.1.30 Providing aluminium ridging of Aluminium Alloy procured from primary aluminium
producer (On submission of certificate of alloy purchasing from primary producer)
including fitting and fixing necessary Aluminium screws, washers etc.
HINDALCO make or equivalent Quality
Sqm
438.86
8.1.31 Providing plain Polycarbonate transparent sheet Ridging including supplying and
fixing necessary self drilling, self tapping screws etc. complete as specified and
directed.
(i) 150 mm lapping
RM
509.21
(ii) 230 mm lapping
RM
584.30
(i) 1.00 mm thick
Sqm
963.78
(ii) 2.00 mm thick
Sqm
1421.60
(iii) 3.00 mm thick
Sqm
2036.58
(i) 0.40 mm thick
Sqm
715.27
(ii) 0.45 mm thick
Sqm
755.32
(iii) 0.50 mm thick
Sqm
836.74
(iv) 0.60 mm thick
Sqm
971.55
(v) 0.80 mm thick
Sqm
1249.19
8.1.32 Providing plain Polycarbonate transparent sheet roofing at all levels with self
drilling, self tapping screws complete (Roof trusses, purlins etc. to be measured and
paid separately.)
8.1.33 Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including
fitting and fixing with self drilling, self tapping screws complete. (Roof trusses,
purlins etc. to be measured and paid separately.)
TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by
the Departement
Page-49
Item
Description
No
8.1.34 Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley /
Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping
screws complete complete.
the Departement
Unit
Rate
(i) 0.40 mm thick
RM
428.12
(ii) 0.45 mm thick
RM
463.79
(iii) 0.50 mm thick
RM
517.31
(iv) 0.60 mm thick
RM
588.66
(v) 0.80 mm thick
RM
784.87
(i) 0.40 mm thick
Sqm
573.83
(ii) 0.45 mm thick
Sqm
600.59
(iii) 0.50 mm thick
Sqm
654.1
(iv) 0.60 mm thick
Sqm
725.45
(v) 0.80 mm thick
Sqm
921.66
(i) 0.40 mm thick
RM
338.9
(ii) 0.45 mm thick
RM
363.82
(iii) 0.50 mm thick
RM
407.14
(iv) 0.60 mm thick
RM
500.51
(v) 0.80 mm thick
RM
611
(i) 0.40 mm thick
Sqm
570.01
(ii) 0.45 mm thick
Sqm
620.97
(iii) 0.50 mm thick
Sqm
678.31
(iv) 0.60 mm thick
Sqm
1058.51
(v) 0.80 mm thick
Sqm
1323.46
RM
424.27
RM
459.6
8.1.35 Providing Pre Painted Galvalume Sheet Roofing (PPGL) at all levels including fitting
and fixing self drilling, self tapping screws complete (Roof trusses, purlins etc. to be
measured and paid separately.)
(a)
the Departement
8.1.36 Providing Pre Painted Galvalume Sheet (PPGL) accessories ( Ridges / Valley / Gutter
/ Flashing) at all levels including fitting and fixing self drilling, self tapping screws
complete.
the Departement
8.1.37 Providing Bare Galvalume Sheet Roofing at all levels including fitting and fixing self
drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured
and paid separately.)
the Departement
8.1.38 Providing Bare Galvalume Sheet roofing accessories (Ridges / Valley / Gutter
/Flashing) at all levels including fitting and fixing self drilling, self tapping screws
complete.
the Departement
(i) 0.40 mm thick
(ii) 0.45 mm thick
Page-50
Item
No
Description
Unit
Rate
(iii) 0.50 mm thick
RM
512.58
(iv) 0.60 mm thick
RM
583.23
(v) 0.80 mm thick
RM
777.52
(i) 0.40 mm thick
Sqm
750.68
(ii) 0.50mm thick
Sqm
855.39
(i) 0.40 mm thick
Sqm
528.98
(ii) 0.50 mm thick
Sqm
556.74
(A) DURASHINE/TATA BLUESCOPE ROOF PROFILE (0.45mm(TCT) x 1072mm)
Sqm
730.23
(B) DURASHINE/TATA BLUESCOPE WALL PROFILE (0.45mm(TCT) x 1150mm)
Sqm
673.44
(C) DURASHINE TILE PROFILE (0.50mm(TCT) x 505mm)
Sqm
1243.86
8.1.39 Providing Pre Painted Steel Tile Sheet at all levels including fitting and fixing self
drilling, self tapping screws complete (Roof trusses, purlins etc. to be measured and
paid separately.)
Dyna roof /Wonder Roof / Durakolar
8.1.40 Providing Pre Painted Steel Tile Sheet accessories at all levels including fitting and
fixing self drilling, self tapping screws complete.
Dyna roof/ Wonder Roof/ Durakolor
8.1.41 Providing colour coated DURASHINE/TATA BLUESCOPE zinc-aluminium profile

sheet (total coated thickness=0.45mm) of nominal 1015mm effective cover width
and nominal 28mm deep ribs with subtle square fluting in the five pan at nominal
203mm centre-to-centre including fasteners class 2 SDS, fitting and fixing complete.
(Roof trusses, purlins etc. to be measured and paid separately.)
8.1.42 Providing colour coated DURASHINE/TATA BLUESCOPE zinc-aluminium roof , wall

and tile profile sheet accessories (total coating thickness=0.45mm) including
fasteners class 2 SDS, fitting and fixing complete. (Roof trusses, purlins etc. to be
(a) (i) Plain Ridge
Sqm
408.32
(b)
(ii) Crimped Curved Ridge
Sqm
847.73
(c )
(iii) Crimped End Curved Ridge
Sqm
847.73
(d)
(iv) Gutter / Flashings
Sqm
520.51
(e)
(v) Plain sheet
Sqm
576.75
CLAY ROOF TILES

8.1.43 Providing and laying machine made clay roof tiles on sloping roof and chajjas over
20mm thick base of cement mortar 1:3 and jointed with grey cement slurry and
joints flush with mortar 1:3 complete.
Sqm
958.53
8.2 ROOF TREATMENT

8.2.1 Grading roof for water proofing treatment with
(a) Cement concrete 1:2:4 (cement: 2 coarse sand: 4 graded stone agg. 20 mm
nominal size)
(b) Cement mortar
(i) 1:3 (1 cement: 3 coarse sand)
(ii) 1:4(1 cement: 4 coarse sand)
cu.m.
cu.m.
cu.m.
6333.98
7399.55
6181.68
Page-51
Item
Description
No
8.2.2 Providing and laying six course water proof treatment with bitumen felt over roof
consisting of first, third and fifth courses of blown or residual bitumen applied hot
@ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth
courses of roofing with felt type 3 grade - I (hessain base self finished bitumen felt)
and sixth and final course with stone grit 6mm and down per sq.m including
preparation of surface, excluding grading complete.
8.2.3 Providing and laying four course water proofing treatment with bitumen felt over
roof consisting of first and third courses of blown or residual bitument applied hot
@ 1.45kg per sq.m of area for each course second course of roofing with felt type 3
grade 1 (hessian base self finished bitumen) and fourth and final course with stone
grit 6mm and down size, felt pea gravel spread @ 0.006m3 per sq.m including
preparation of surface, excluding grouting etc. as directed and specified.
Unit
Rate
Sqm
253.7
Sqm
175.99
8.2.4 Providing and application of Insultech safeguard coating for heat reflecting and
waterproofing of approved colour as per direction of engineer in charge
Sqm
453.07
8.2.5 Providing and fixing of leak proof,fire retardant and Uv resistant skylighting galzing
with Lexan polycarbonate sheet fixed with specially designed Domal management
system confirming to IS:737 alloy & temper 6063 - T6 with a UTS of 180 to 200 mpa
and weight of 1.03 kg/mtr. approx with EPDM rubber gasket of specific gravity as
per ISO 2781,age resistant as per ASTM - D573 hardness as per 2240 & tensile
strength as per ASTM 412 including the silicon sealent GE Bayer Weathersil NY as
per drawing and directed by the Engineer in charge.
(a) Polycarbonate Sheet (Compact)
(i) 3mm thick
Sqm
5265.42
(i) 4mm thick
Sqm
6271.78
(i) 6mm thick
Sqm
4093.46
(ii) 8mm thick
Sqm
4806.82
(iii) 10 mm thick
Sqm
5456.5
(i) 1.00mm thick
Sqm
1876.34
(ii) 1.20mm thick
Sqm
2080.16
(i) 1.0 mm thick
Sqm
735.92
(ii) 1.3 mm thick
Sqm
774.13
(iii) 1.5 mm thick
Sqm
863.31
(b) Polycarbonate Sheet (Multiwall)
(c ) Polycarbonate Sheet (76/16 Corrugated)
8.2.6 Providing laying and fixing of FINROOF Finolex PVC roofing sheet of approved
thickness / colour and profile as per drawing and as directed by the engineer in
charge
(a) 76/16 Greca Profile
(b) 250/40 Industrial Profile

(i) 1.8 mm thick
Sqm
971.58
(ii) 2.0 mm thick
Sqm
1041.65
(iii) 2.5 mm thick
Sqm
1169.04
Page-52
CH-9 : WOOD WORKS

Item
No
9.1 CHOWKATHS
Description
Unit
Rate
9.1.1 Providing dressed wood work in post, walls,battens, post plate

bressumers etc. includingsupplying and fixing with spikes, nails,bolt and
nuts of 12mm dia(M.S) and required length etc.complete with kiricide oiling
two coats to faces in contact with C.C or masonry (M.S flats, angle cleats
and bolt and nuts required for flats,angle cleats wherever use shall be
(a) With sal wood
Cum
Rs.98,776.83
(b) With Hollock timber
Cum
Rs.56,388.61
(c) With Bonsum/ Sundi timber
Cum
Rs.57,577.71
(d) With Bola timber
Cum
Rs.49,716.53
(e) With 2nd class treated timber
Cum
Rs.39,900.78
(a) With sal wood
Cum
Rs.121,163.03
(b) With 1st class timber (Bonsum/ Sundi)
Cum
Rs.77,474.00
(a) With sal wood
Cum
Rs.87,836.62
(b) With Hollock/ Sundi/ Sam
Cum
Rs.51,443.43
(c) With 2nd class treated timber
Cum
Rs.35,715.37
Cum
Rs.97,125.37
Cum
Rs.58,905.75
R.M.
349.75
R.M.
Rs.498.76
9.1.2 Providing wood work in frame (chowkaths) of doors, windows, clerestory

windows and other similar works wrought, framed and fixed in position in
contact with C.C or brick masonry wall including supplying, fitting and fixing
with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement
concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the
timber faces in contact with C.C and masonry as directed and specified.
9.2 ROOF TRUSS

9.2.1 Providing undressed wood work in roof truss, rafter, purlin, tie and the like
including hoisting and fixing in position with necessary spikes, nails including
M.S straps with bolt and nuts etc.complete with kiricide oiling two coats to all
timber members and two coats of anticorrosive paint to M.S straps (M.S
flats, angle cleats, and bolt and nuts required for flat and angle cleats
wherever used shall be measured and paid separately)
9.3
CEILING AND PARTITION
9.3.1 Providing wood work in frame of false ceiling partitions etc.sawn, wrought,
framed hoisted and fixed in positon with spikes, nails, M.S flat,angle/ cleats
with bolt and nuts complete including kiricide oiling two coats to unexposed
surfaces of the timber (M.S flats, angle cleats, and bolt and nuts required for
flat, angle cleats wherever necessary shall be measured and paid
separately)
(a) With sal wood
(b) With Gamari/ Bonsum/ Sundi
9.4 BARGE BOARD
9.4.1 Providing barge board of size 200mm x 20mm with 1st class local Hollock/
Bonsum timber including fitting and fixing with necessary wood screws etc.
complete.
9.5
PELMET
9.5.1 Providing and fixing 12 mm thick and 150mm wide pelmet with 25 mm dia
wooden curtain rod and bracket including fixing with 15mmx3mm M.S flat
100mm long plugs complete.
(a) First class Indian Teak wood/ Sisu wood
Vh-9 : Wood Works
Page-53
Item
No
Description
Unit
Rate
(b) First class local wood(Gamari)
R.M.
Rs.339.16
(c) First class local wood(Hollock/ Bonsum)
R.M.
Rs.339.16
(d) Veneered particle board (12 mm thick)
R.M.
Rs.484.60
e) Extra for providing and fixing brass curtain rail with rollers,stoppers and
brakets in pelmet instead of wooden curtain rods 25 mm dia with
R.M.
Rs.1,260.10
(i) 20 mm dia.
R.M.
Rs.1,260.10
(ii) 25 mm dia.
R.M.
Rs.1,266.57
(I) 20 mm dia.
R.M.
Rs.335.63
(ii) 25 mm dia.
R.M.
Rs.335.63
(a)With Sunmica
R.M.
Rs.2,344.41
(b)Without Sunmica
R.M.
Rs.1,826.39
(a)With Teak wood/Sissu wood.
R.M.
Rs.166.37
(b)With Bonsum/ Sundi wood.
R.M.
Rs.126.01
(e)With Holok timber
R.M.
Rs.124.82
(c)With Bola wood
R.M.
Rs.118.15
R.M.
Rs.115.30
(b)With Bonsum/ Sundi wood.
R.M.
Rs.100.66
(c)With Bola wood
R.M.
Rs.97.81
(d)With Gamarai Wood.
R.M.
Rs.100.66
(e)With Holok timber
R.M.
Rs.100.23
R.M.
Rs.65.85
(b) With Bonsum/ Sundi wood.
R.M.
Rs.51.64
(c)With Bola wood
R.M.
Rs.51.20
brakets (actual length of the rods to be measured)

f) Extra for providing and fixing curtain rod of 1.25 mm thick wire brass plate
with braket instead of wooden curtain rod of 25mm dia brackets (actual
length of the rods to be measured)
g) Extra for providing and fixing curtain rod of 1.25mm thick chromium plated
with brass plate with to chromium plated brass brackets fixed with CP brass
screws etc. complete.(actual length of the rods to be measured)
9.5.2 Supplying, fitting and fixing pelmet to door and window frames with 12mm
thick kit ply wood finished with matt finished sunmica on external faces and
bottom and fixed with wooden brackets including providing 20mm dia
aluminium hanger with necessary socket and clamps complete including
inside painting as directed.
9.6
ARCHITRAVE / BEADING
9.6.1 Providing and fixing 1st class timber moulded architrave of size 50x20mm to
door and window frames with countersunk wood screw,wooden plugs and
applying a coat of wood preservative on unexposed surface etc.
9.6.2 Providing and fixing 1st class timber moulded beading of size 25mm x
15mm around panel inserts of doors with countersunk wood screws
including applying a coat of wood preservative on unexposed surface.
9.6.3 Providing and fixing 1st class timber beading for fixing clear sheet glass/
frosted glass including applying a coat of wood preservative on unexposed
surface.
Vh-9 : Wood Works
Page-54
Item
No
Description
Unit
Rate
(d)With Gamarai Wood.
R.M.
Rs.51.64
(e) With Holok timber
R.M.
Rs.51.20
R.M.
Rs.882.53
(b) With 1st class local wood (Hollock )
R.M.
Rs.559.32
(c) With 1st class Bola wood
R.M.
Rs.507.41
(d) 1st class local wood (Gamari/Bonsum )
R.M.
Rs.568.57
(a) With 1st class Teak wood / Sissu wood
R.M.
Rs.1,323.79
(b) With 1st class local wood (Hollock)
R.M.
Rs.838.97
R.M.
Rs.761.12
(d) 1st class local wood (Gamari / bonsum )
R.M.
Rs.852.85
R.M.
Rs.57.92
(a) With 1st class Teak wood / Sissu wood
R.M.
Rs.246.75
(b) With 1st class local wood

(Gamari/Hollock/Bonsum )
R.M.
Rs.220.72
R.M.
Rs.216.54
(i) 1st class local wood

(Gamari/Bonsum/Holok)
9.8.2 Providing first clas local wood (Hollock/ Bonsum ventilating louvre of
wooden frame (minimum size of frame members 150mm x 75mm) with clear
glass/ frosted glass including fitting and fixing and painting two coats of
kiricide oil complete as directed for all levels.
Sq.m.
Rs.1,689.07
Sq.m.
Rs.2,251.75
9.8.3 Providing Sal wood ventialating louvre of wooden frame (minimum size
frame members 150mmx75mm) with clear glass/frosted glass including
fitting and fixing and painting with two coats of kiricide oiling complete as
directed for all levels.
Sq.m.
Rs.3,675.18
(i) 40 mm thick.
Sq.m.
Rs.4,333.57
(ii) 35 mm thick.
Sq.m.
Rs.4,033.34
(iii) 30 mm thick.
Sq.m.
Rs.3,561.77
9.7
Railing/Balustrade
9.7.1 Providing and fixing wooden 100mmx 60mm rounded hand rails in straight
lengths complete.
(a) With Teak wood/Sissu wood.
9.7.2 Providing and fixing wooden 100mmx60 mm moulded hand rails in place of
rounded hand rail.
9.7.3 Extra for hand rails if sunk to receive iron core.

9.7.4 Providing and fixing 25mmx25mm first class timber balustrade 25mmx25mm
square, wrought fixed with ends housed (square or splayed) to hand rails
and trends or strips complete.
9.8 VENTILATING LOUVRE

9.8.1 Providing 1st class local wood (Hollock/Bonsum)ventilating louvre in 50mm
x 38mm size wooden frame with 150mm x 20mm slate made of 1st class
local wood including fitting and fixing with nails and painting with two coats of
kiricide oiling complete.
9.9 DOORS / WINDOWS / VENTILATORS / CLERESTORY WINDOWS

9.9.1 Providing fitting and fixing 1/3 panelled 2/3 glazed wooden shutters for
doors/windows including oxidised iron butt hinges (100mm x75 mm x3.55
mm) with necessay screws including glass panes (other fittings to be
A) With Teak wood / Sissu
Vh-9 : Wood Works
wood.
Page-55
Item
No
Description
Unit
Rate
B) With 1st class local wood

(i) 40 mm thick.
Sq.m.
Rs.2,989.95
(ii) 35 mm thick.
Sq.m.
Rs.2,823.88
(iii) 30 mm thick.
Sq.m.
Rs.2,566.27
C) With 1st class Local wood ( Bola wood)

(i) 40 mm thick.
Sq.m.
Rs.2,718.16
(ii) 35 mm thick.
Sq.m.
Rs.2,577.90
(iii) 30 mm thick.
Sq.m.
Rs.2,350.21
(i) 40 mm thick.
Sq.m.
Rs.5,026.46
(ii) 35 mm thick.
Sq.m.
Rs.4,623.51
(iii) 30 mm thick.
Sq.m.
Rs.3,618.01

(i) 40 mm thick.
Sq.m.
Rs.3,316.46
(ii) 35 mm thick.
Sq.m.
Rs.3,150.88
(iii) 30 mm thick.
Sq.m.
Rs.2,532.56
C) With 1st class Local wood ( Bola wood)

(i) 40 mm thick.
Sq.m.
Rs.3,265.22
(ii) 35 mm thick.
Sq.m.
Rs.3,103.58
(iii) 30 mm thick.
Sq.m.
Rs.2,500.03
(i) 40 mm thick with panel inserts of 20mm thickness.
Sq.m.
Rs.5,377.75
(ii) 35 mm thick with panel inserts of 20mm thickness.
Sq.m.
Rs.4,593.09
(iii) 30 mm thick with panel inserts of 20mm thickness.
Sq.m.
Rs.4,390.23
Sq.m.
Rs.3,740.34
Sq.m.
Rs.3,303.89
Sq.m.
Rs.3,191.05
Sq.m.
Rs.3,692.10
9.9.2 Providing, fitting and fixing full panelled doors/ windows including oxidised
M.S butt hinges (100mm x75 mm x3.55mm) with necessary screws (other
fittings to be measured and paid separately )
A) With Teak wood / Sissu wood.
9.9.3 Providing, fitting and fixing factory made wooden panelled doors with panel
inserts of 75mm to 50mm width and 12mm to 20mm thickness,joined
together with continous tongue and groove joints glued together with
Movicol or other approved adhesive leaving a vertical groove of 7.5mm to
15mm between the inserts,the edges of panel inserts being feather tongue
into styles and rails including providing three pairs of oxidised M.S butt
hinges (100mm x75 mm x3.55mm) and furnishing with moulded timber
beading of size 25mmx15mm around the panels complete as per drawing
(moulded timber bead and all fittings except hinges to be paid separately)
a) With Teak wood / Sissu
wood.
b) With 1st class local wood (Hollock / Gamari/Sundi/ Bonsum)
c) With 1st class local wood (Bola/Sundi)

Vh-9 : Wood Works
Page-56
Item
No
Description
Unit
Rate
Sq.m.
Rs.3,265.91
Sq.m.
Rs.3,155.72
(a) Using Bonsum/Holok wood
Sq.m.
Rs.2,152.51
(b) Using Gamri wood
Sq.m.
Rs.2,152.51
9.9.4 Providing fitting and fixing 1st class local wood battened, framed and braced
door and window shutters including oxidised iron butt hinges (100mm x58
mm x1.90 mm) 6 nos with necessay screws.
9.9.5 Providing fitting and fixing 1st class local wood battened and framed door
and window shutters including oxidised iron butt hinges (100mmx 58mmx
1.90mm) 6 nos with necessay screws.
Sq.m.
Sq.m.
Rs.1,931.47
(b) Using Gamari wood
Sq.m.
Rs.1,931.47
(i) 25mm thick
Sq.m.
Rs.3,303.39
(ii) 20mm thick
Sq.m.
Rs.2,871.47
(i) 25mm thick
Sq.m.
Rs.3,303.39
(ii) 20mm thick
Sq.m.
Rs.2,871.47
(i) 40mm thick
Sq.m.
Rs.3,013.90
(ii) 35mm thick
Sq.m.
Rs.2,604.24
(iii) 30mm thick
Sq.m.
Rs.2,351.00
(i) 40mm thick
Sq.m.
Rs.1,967.52
(ii) 35mm thick
Sq.m.
Rs.1,830.81
(iii) 30mm thick
Sq.m.
Rs.1,689.94
(i) 40mm thick
Sq.m.
Rs.1,941.52
(ii) 35mm thick
Sq.m.
Rs.1,808.02
(iii) 30mm thick
Sq.m.
Rs.1,670.47
9.9.6 (a) Providing fitting and fixing 1st class local wood battened, ledged and
braced door and window shutters including oxidised iron butt hinges
(100mmx 58mmx1.90mm) 6 nos with necessay screws.
(b) Using Gamari wood
9.9.7 Providing, fitting and fixing fully glazed window with sash bars including
oxidised M.S butt hinges (75mmx 60mmx3.15mm) 2nos.on each leaf and 3
nos. on single leaf (glass panes to be measured and paid separately)
wood.
B) With Holock/Gamari/Bonsum wood.
C) With 1st class local wood
9.9.8 Providing, fitting and fixing fully glazed window without intermediate sash
bars including oxidised M.S butt hinges (75mm x 60mm x 3.15mm) 2nos.on
each leaf and 3 nos. on single leaf (glass panes to be measured and paid
separately)
9.9.9 Providing, fitting and fixing fully glazed clerestory window and fan light
including fitting and fixing 2 M.S pivot hinges (75mm x 20mm x 3mm), eye
hook and nylon chord complete (glass panes shall be measured and paid
separately)
Vh-9 : Wood Works
Page-57
Item
No
Description
Unit
Rate
wood.
(i) 40mm thick
Sq.m.
Rs.2,484.49
(ii) 35mm thick
Sq.m.
Rs.2,286.07
(iii) 30mm thick
Sq.m.
Rs.2,279.95
(i) 40mm thick
Sq.m.
Rs.1,758.06
(ii) 35mm thick
Sq.m.
Rs.1,647.69
(iii) 30mm thick
Sq.m.
Rs.1,528.12
(i) 40mm thick
Sq.m.
Rs.1,736.65
(ii) 35mm thick
Sq.m.
Rs.1,628.88
(iii) 30mm thick
Sq.m.
Rs.1,512.12
(I)40mm thick
Sq.m.
Rs.2,533.85
(II)35mm thick
Sq.m.
Rs.2,341.13
(I)40mm thick
Sq.m.
Rs.1,846.28
(II)35mm thick
Sq.m.
Rs.1,739.05
(I)40mm thick
Sq.m.
Rs.1,712.33
(II)35mm thick
Sq.m.
Rs.1,621.76
(i) 40mm thick
Sq.m.
Rs.2,289.07
(ii) 35mm thick
Sq.m.
Rs.2,189.00
(iii) 30mm thick
Sq.m.
Rs.2,088.33
Sq.m.
Rs.2,650.88
B) With Holock/Gamari/Bonsum wood.
C) With 1st class local wood
9.9.10 Providing, fitting and fixing fully glazed wooden door shutters with necessary
butt hinges, screws etc. complete as per approved drawing as directed and
specified at all levels.(fittings e.g. tower bolt, door handle, aldrop, glass
panes etc. should be measured and paid seperately.)
(a) With Teak or Sissu Wood
(b) With Gamari Wood.
(c) With 1st class local wood
9.10 VENEERED PARTICLE BOARD DOOR SHUTTERS

9.10.1 Providing, fitting and fixing factory made exterior type fully panelled single
leaf door shutters of approved brand conforming to relevent I.S code
having kiln seasoned and vacuum pressure treated Hollock / Bonsum /
Sundi rail and styles with pannel of Anchor brand 12mm thick veneered
Teak wood particle board bonded with phenol - formaldehyde synthetic resin
adhesive conforming to relevent I.S code including 4 nos of oxidised iron
butt hinges (100mm x75 mm x3.55mm) to each leaf complete.
9.10.2 Extra for double leaf door shutters, 10% cost for single leaf shutters as in
item nos 9.10.1
9.11 CUPBOARD SHUTTERS
9.11.1 Providing and fixing 25mm thick wooden shutters for cup board including
black enamelled M.S butt hinges (75mmx 40mmx1.12mm) 6 nos. with
necessary wood screws (fully panelled)
(i) Using wooden plank
a)With Teak wood / Sissu
Vh-9 : Wood Works
wood.(fully panelled)
Page-58
Item
No
Description
Unit
Rate
b) With Gamari/ Sundi/ Bonsum wood.
Sq.m.
Rs.2,028.73
c) With 1st class local timber.
Sq.m.
Rs.2,028.73
d) With 1st class local timber (Hollock )
Sq.m.
Rs.2,010.26
a) With Teak wood particle board (12mm thick)
Sq.m.
Rs.2,658.24
b) With Teak wood particle board (19mm/20mm thick)
Sq.m.
Rs.2,964.21
c) With block board (both side commercial 16mm thick)
Sq.m.
Rs.1,819.36
d) With block board (both side commercial 19mm/20mm thick)
Sq.m.
Rs.2,985.88
e) With block board (one side commercial and other side teak 12mm thick)
Sq.m.
Rs.2,093.46
f) With block board (one side Teak and other sidecommercial 19mm/20mm
thick)
(g) With Anchor brand veneered, plyboard bonded with phenol
formaldehyde synthetic resin 12 mm thick.
Sq.m.
Rs.2,985.88
Sq.m.
Rs.2,326.77
Sq.m.
Rs.3,190.73
(ii) 35 mm thick .
Sq.m.
Rs.2,990.57
(iii) 30 mm thick .
Sq.m.
Rs.2,812.24
(iv) 25 mm thick .
Sq.m.
Rs.2,615.72
(i) 40 mm thick .
Sq.m.
Rs.2,493.20
(ii) 35 mm thick .
Sq.m.
Rs.2,293.03
(iii) 30 mm thick .
Sq.m.
Rs.2,114.71
(iv) 25 mm thick .
Sq.m.
Rs.1,918.18
Sq.m.
Rs.2,857.13
(ii) 35 mm thick .
Sq.m.
Rs.2,656.96
(iii) 30 mm thick .
Sq.m.
Rs.2,439.99
(iv) 25 mm thick .
Sq.m.
Rs.2,253.77
(i) 40 mm thick .
Sq.m.
Rs.3,445.84
(ii) 35 mm thick .
Sq.m.
Rs.3,154.94
(iii) 30 mm thick .
Sq.m.
Rs.2,860.22
(ii) Using Particle/Block bord
9.12 BLOCK BOARD SHUTTERS

9.12.1 Providing and fixing flush door shutters solid core construction with frame of
1st class hard wood with cross band and face veneered ply wood face
panels conforming to relevent I.S code including oxidised iron butt hinges
(100mm x 75mm x 3.5mm) 6 nos with necessary wood screws.
a) Decorative type face panel and block board core.
(i) 40 mm thick .
b) Non decorative type and block board core.
c) One face decorative and other face nondecorative type and block board
core.
(i) 40 mm thick .
9.13 WIRE GAUGE SHUTTERS

9.13.1 Providing, fitting and fixing Wire gauge shutters using galvd. M.S. wire of I.S
designation 85G with wire of dia 0.56mm for doors, windows and clerestory
windows including oxidised M.S butt hinges (100mm x 58mm x1.90mm)
Vh-9 : Wood Works
wood.
Page-59
Item
No
Description
Unit
Rate
B) With Gamari/ Bonsum/ Sundi wood.

(i) 40 mm thick .
Sq.m.
Rs.2,408.02
(ii) 35 mm thick .
Sq.m.
Rs.2,246.21
(iii) 30 mm thick .
Sq.m.
Rs.2,082.28
(i) 40 mm thick .
Sq.m.
Rs.2,377.44
(ii) 35 mm thick .
Sq.m.
Rs.2,219.44
(iii) 30 mm thick .
Sq.m.
Rs.2,059.36
(i) 40 mm thick .
Sq.m.
Rs.2,377.44
(ii) 35 mm thick .
Sq.m.
Rs.2,219.44
(iii) 30 mm thick .
Sq.m.
Rs.2,059.36
a) With 1st class local timber bead
Sq.m.
Rs.459.34
b) With 2nd class local timber bead
Sq.m.
Rs.407.03
a) With 1st class local timber bead
Sq.m.
Rs.521.56
b) With 2nd class local timber bead
Sq.m.
Rs.469.25
Sq.m.
Rs.2,159.12
Sq.m.
Rs.1,849.60
Sq.m.
Rs.2,378.21
Sq.m.
Rs.2,211.59
C) With 1st class local wood(Hollock)
D) With 1st class local wood. (Bola)
9.13.2 Providing, fitting and fixing Expanded metal 20mm x 60mm strands 3.25mm
wide and 1.6mm thick for windows, openings etc. including fixing 50mm
20mm beading of timber with necessary nails, wood screws etc. complete
9.13.3 Providing, fitting and fixing fly-proof galvd. M.S. wire gauge of I.S.
designation 85 G with wire of dia. of 0.56mm to windows and clerestory
windows including timber beading of size 50mmx 20mm complete.
9.14.1 Supplying, fitting and fixing 30mm thick flush door(single leaf finished)
made of phenol bonded Duratuff exterior grade (both side) plain medium
density fibre board using 4 nos of hinges 125mm long ensuring that the
hinges are not fixed less than 150mm from the edges with 8 nos. parallel
sunk fully threaded screws 38mm long, should be used for fixing the hinges
to the flush door after drilling a pilot hole 2.50mm dia 40mm long . Screws
should not be hammered . Lock, tower bolts etc. necessary.
(a) 30mm thick.
i) Both side teak.
ii) One side teak and other side commercial.
(b) 40mm thick.
i) Both side teak.
ii) One side teak and other side commercial.
9.15 MISCELLENEOUS
9.15.1 Extra for using bright finished Nickel plated M.S piano hinges in place of
oxidised M.S.butt hinges.
No
Rs.11.78
9.15.2 Extra for providing lapping with 1st class Teak wood battens of 25mm
minimum depth on all edges of the shutters.
Sq.m.
Rs.424.48
9.15.3 Extra for wood work for each subsequent floor above 1st floor level.
cu.m.
Rs.153.10
9.15.4 Extra for fitting and fixing doors/windows for each subsequent floor above
1st floor level.
Sq.m.
Rs.8.83
9.15.5 Extra for providing lapping with 1st class Teak wood battens of 25mm
minimum depth on all edges of the shutters.
Sq.m.
Rs.468.65
Vh-9 : Wood Works
Page-60
Item
Description
No
9.16.1 Providing, fitting and fixing Bison Panel board (Cement Bonded Particle
Board) door shutters fixed to 100mmx38mm wooden frames with necessary
hinges, screws, bolts etc. including painting of door shutters (one coat
primer and two coats painting) complete as specified and directed by the
department for all floors (Door fittings to be measured and paid separately)
Unit
Rate
(a) Using 10mm thick board

(i) Both sides commercial
Sq.m.
Rs.1,960.30
(ii) One side laminated
Sq.m.
Rs.1,971.74
(iii) Both sides laminated
Sq.m.
Rs.1,924.58
(i) Both sides commercial
Sq.m.
Rs.1,934.13
(ii) One side laminated
Sq.m.
Rs.2,011.86
(iii) Both sides laminated
Sq.m.
Rs.2,208.63
Sq.m.
Rs.1,858.03
Sq.m.
Rs.2,091.04
(i) 9 mm thick
Sq.m.
Rs.1,607.13
(ii) 12mm thick
Sq.m.
(a) Using 16mm thick board
9.17.1 Providing, fitting and fixing 38mm Melamine faced pre-laminated cellular
core Flush Door with 9mm/12mm thick high density exterior grade
laminated particle board fixed to the internal wooden frame of Sal/Hollock
wood with Polyurestene central core, fixed to the chowkath with necessary
hinges, screws, bolts etc. as specified and directed at all levels.(Door
fixtures to be measured and paid separately.)
(a)With Bhutan Board-Exterior Grade
(One side Decorative)
(i) 9 mm thick
(ii) 12mm thick
(b)With Nepal Board-Exterior Grade
(One side Decorative)
Rs.1,728.14
9.18.1 Providing, fitting and fixing factory made Santro Flush door shutters
having core & cross bands fabricated from seasoned 1st class timber,
25mm core battens, 2.5mm to 3.5mm uniformly thick cross bands, styles &
rails made from hardwood timber of width not less than 50mm, fixed to the
door frames (chowkath) with necessary hinges, screws, bolts etc. as
specified and directed at all levels (Door fixtures and fittings to be measured
and paid seperately.)
(a) 30 mm thick
Sq.m.
Rs.1,988.33
(b) 35mm thick
Sq.m.
Rs.2,123.11
(c) 40 mm thick
Sq.m.
Rs.2,282.67
(a) 75mm x 50mm Solid Frame.
R.M.
Rs.1,256.89
(b) 50mm x 25mm Solid Frame.
R.M.
Rs.731.77
(c )75mm x 50mm Grooved Frame.
R.M.
Rs.1,030.98
9.19. DUROSAM DOORS, WINDOWS & CHOWKHATS

9.19.1 Providing, fitting and fixing Natural Fibre Thermosets Composite of jute,
polymer and chemicals, Durosam make door and window frames
(chowkhats) fixed to the columns / stiffeners / walls with necessary holdfast /
sleeves etc. as specified and directed at all levels.
Vh-9 : Wood Works
Page-61
Item
Description
No
9.19.2 Providing, fitting and fixing Natural Fibre Thermosets Composite of jute,
polymer and chemicals, Durosam make door/ window shutters fixed to the
door/ window frames (chowkath) with necessary hinges, screws, bolts etc.
as specified and directed at all levels (Door/ window fixtures and fittings to
be measured and paid seperately.)
(a) Solid Core moulded/ Fabricated/ Panelled/ Glazed Doors
(b) Flush Doors
(c)Solid Core moulded/ Fabricated/ Panelled/ Glazed Windows
9.20.1 Providing fitting and fixing compressed ready to fit Godrej make wood door
shutter (Godrej Entranza Moulded Panel Door) for various thickness
Conforming to IS 15380-2003,printed,shutter comprising of High Density
Fiberboard skins (HDF) of 3.5 mm (hardened finely processed natural wood
fibre) with panel design compressed on both faces,sandwitching, termite
and borer resistant chemical treated and kiln seasoned wooden stiles and
rails of 50mm-60mm width,lock block and high density flax board core /
chemical treated and kiln seasoned timber core infil. The panel would be of
different design viz. Two panel,Four panel,Six panel (both side) Shutter
should be bonded with Phenol Formaldehyde or adhesive / conforming to
BWP grade of IS 848.Shutter should have trim ability option of 12.5 mm
from all sides. The door should have flexibility for painting or polishing to
match any interiors.
Unit
Sq.m.
Sq.m.
Sq.m.
Rate
Rs.6,251.82
Rs.3,357.58
Rs.4,088.72
Sq.m.
Rs.2,826.48
Sq.m.
Rs.2,918.15
Sq.m.
Rs.3,223.87
Vh-9 : Wood Works
Page-62
Ch-10: GRILL
Item
No.
10 GRILLS
Unit
Rate
10.1
Providing, fitting and fixing M.S. round bars with M.S. flat stiffeners at required
spacing in wooden frames of windows and clerestory windows
Kg
Rs.76.22
10.2
Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory
windows/ openingwith M.S. flats at required spacing in frame all round, squre or
round M.S. bars with round headed bolts and nuts or screws.
(a) Fixed to wooden frames
Kg
Rs.84.55
(b) Fixed to steel frames
Kg
Rs.84.16
(c) Fixed to Brickwork/P.C.C/R.C.C.
Kg
Rs.88.74
(a) Fixed to wooden frames
Kg
Rs.101.34
(b) Fixed to steel frames
Kg
Rs.100.58
(c) Fixed to Brickwork/P.C.C/R.C.C.
Kg
Rs.106.20
I . Plain grill
II Ornamental grill
10.3
Supplying, fitting and fixing anodised aluminium decorated grill with anodised
aluminium rectangular frame of 'F' and 'H' section fitted with walls, columns or
stiffeners by special type of screws as per specification by the Department for all
levels. (Aluminium Alloy procured from primary aluminium producer (On
submission of certificate of alloy purchaging from primary producer)
Sqm
Rs.2,098.22
10.4
Extra for providing security grill welded to casement window frames With 16mm
dia M.S round placed horizontally at a distance of 10 cm c/c @ 15kg/ 16kg per
sq.meter as per approved drawing.
Sqm
Rs.1,150.47
Ch-10 : Grill Works
Page-63
CHAPTER-11: ALUMINIUM DOORS, WINDOWS AND OTHER WORKS

Description
Item
No.
Unit
Rate
i) 6 mm clear glass
Sqm
Rs.5,980.92
ii)5mm frosted glass
Sqm
Rs.6,020.77
iii) 6mm coloured glass
Sqm
Rs.6,136.02
iv) 5 mm clear glass
Sqm
Rs.5,852.89
v) 5 mm coloured glass
Sqm
Rs.6,007.99
(b)Fixed windows and ventilators

i) 6mm clear glass
Sqm
Rs.2,700.05
ii) 5mm frosted glass
Sqm
Rs.2,739.91
iii) 6mm coloured glass
Sqm
Rs.2,855.14
iv) 5 mm clear glass
Sqm
Rs.2,572.03
v) 5 mm coloured glass
Sqm
Rs.2,668.85
(a)2 Track sliding window

(i)6mm clear glass
Sqm
Rs.4,766.85
(ii)5mm frosted glass
Sqm
Rs.4,302.54
(iii)6mm coloured glass
Sqm
Rs.4,414.41
(iv) 5 mm clear glass
Sqm
Rs.4,627.17
(v) 5 mm coloured glass
Sqm
Rs.5,224.19
(b)3 Track sliding window

(i)6mm clear glass
Sqm
Rs.4,839.56
Sqm
Rs.4,878.26
Sqm
Rs.4,990.13
Sqm
Rs.4,712.14
Sqm
Rs.4,865.83
WINDOWS AND VENTILATORS

11.1.1 Providing, fitting and fixing anodised aluminium windows and ventilators of
standard sections of approved brand without horizontal glazing bars joints mitred
and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm
lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix
including providing and fixing handles, frictions stays, joining cleat, bolting device,
locking arrangement, spring catch as required complete as specified and directed
for all levels. (Cement concrete to be measured and paid separately).
a)Side hung and Top hung windows and ventilators
11.1.2 Providing, fitting and fixing anodised aluminium sliding windows and ventilators of
standard sections of approved brand without horizontal glazing bars, joints mitred
and welded (manufactured to relevant IS specifications) and providing and fixing
handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements,
screws etc as required complete as specified and directed for all levels.
11.1.3 Providing, fitting and fixing coloured anodised aluminium windows and ventilators
of standard sections of approved brand without horizontal glazing bars joints
mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x
3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in
1:3:6 mix including providing and fixing handles, frictions stays, joining cleat,
bolting device, locking arrangement, spring catch as required complete as specified
and directed for all levels.(Cement concrete to be measured and paid separately).
Ch-11 : Alluminium Doors, Windows other Works
Page-64
Description
Item
No.
Unit
Rate
(i)6mm clear glass
Sqm
Rs.6,972.55
Sqm
Rs.6,082.45
Sqm
Rs.6,194.32
Sqm
Rs.5,919.46
Sqm
Rs.6,070.02
(i)6mm clear glass
Sqm
Rs.2,712.60
Sqm
Rs.2,751.30
Sqm
Rs.2,863.17
Sqm
Rs.2,588.31
Sqm
Rs.2,738.87
Sqm
Rs.4,949.42
Sqm
Rs.4,988.12
Sqm
Rs.5,099.98
Sqm
Rs.4,825.12
Sqm
Rs.5,085.13
(i)6mm clear glass
Sqm
Rs.5,046.09
Sqm
Rs.5,084.78
Sqm
Rs.5,296.66
Sqm
Rs.4,921.79
Sqm
Rs.5,072.35
(i) With 6mm thick glass panes
Sqm
Rs.4,967.67
(ii) With 5mm thick glass panes
Sqm
Rs.4,653.47
(i) With 6mm thick glass panes
Sqm
Rs.5,245.61
(ii) With 5mm thick glass panes
Sqm
#REF!
a)Side hung and Top hung windows and ventilators
(b)Fixed windows and ventilators
11.1.4 Providing, fitting and fixing coloured anodised aluminium sliding windows and
ventilators of standard sections of approved brand without horizontal glazing
bars,joints mitred and welded (manufactured to relevant IS specifications) and
providing and fixing handles, angle cleat, rubber gasket, roller, bolting device,
locking arrangements, screws etc as required complete as specified and directed
for all levels.
(i)6mm clear glass
(b)3 Track sliding window
11.1.5 a) Providing, fitting and fixing anodised aluminium fixed windows and ventilators of
standard sections of approved brand, joints mitred welded (manufactured to
relevant I.S. specification) fitted with glass panes of required thickness and 12mm
prelaminated boards and providing and fixing handles, angle cleat, rubber
gusket,roller bolting device, screws as required complete as specified and directed
for all levels.
(a) In Normal anodised Aluminium section
(b) In Coloured anodised Aluminium section
11.2
DOORS
Page-65
Description
Item
No.
11.2.1 Providing, fitting and fixing anodised aluminuim framed glazed doors with anodised
aluminium frame made of 100mm x 45mm x 2.5mm section of approved brand
with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock
rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with
glazing clip, special type rubber gasket complete including hydraulic floor spring,
pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc
complete as specified and directed by the department at all levels.
Unit
Rate
(i) 6mm clear glass
Sqm
Rs.10,422.37
(ii) 5mm frosted glass
Sqm
Rs.10,461.07
(iii) 6mm coloured glass
Sqm
Rs.10,572.94
(iv) Prelaminated Board

(v) 5 mm clear glass
Sqm
Sqm
Rs.10,506.21
Rs.10,298.08
(vi) 5 mm coloured glass
Sqm
Rs.10,448.64
(i) 6mm clear glass
Sqm
Rs.9,906.66
(ii) 5mm frosted glass
Sqm
Rs.9,945.36
(iii) 6mm coloured reflectory glass
Sqm
Rs.11,585.84
Sqm
Rs.9,990.51
Sqm
Rs.9,782.37
Sqm
Rs.9,932.93
(i)6mm clear glass
sqm
Rs.10,561.74
sqm
Rs.10,600.44
sqm
Rs.10,712.30
sqm
Rs.10,645.58
sqm
Rs.10,623.47
sqm
Rs.10,588.01
11.2.2 Providing,fitting and fixing anodised aluminuim framed glazed doors with anodised
aluminium frame made of 63mm x 38mm x 2.5mm section of approved brand with
door style of size 50mm x 45mm x 2.0mm, top rails 50mm x 45mm x 2.5mm,
middle rail 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm
fitted with glazing clip, special type rubber gasket complete including hydraulic
floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles,
cleat etc complete as specified and directed by the department at all levels.
11.2.3 Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with
anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door
style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails
100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with
glazing clip, special type rubber gasket complete including hydraulic floor spring,
pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc
11.2.4 Providing,fitting and fixing coloured anodised aluminuim framed glazed doors with
anodised aluminium frame made of 63mm x 38mm x 2.5mm section of approved
brand with door style of size 50mm x 45mm x 2.0mm, top rails 50mm x 45mm x
2.5mm, middle rail 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x
2.5mm fitted with glazing clip, special type rubber gasket complete including
hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock,
angles, cleat etc complete as specified and directed by the department at all levels.
Page-66
Description
Item
No.
Unit
Rate
(i)6mm clear glass
Sqm
Rs.10,221.86
Sqm
Rs.10,260.56
Sqm
Rs.10,372.42

Sqm
Sqm
Rs.10,305.70
Rs.10,097.56
Sqm
Rs.10,248.13
(i)6mm clear glass
Sqm
Rs.7,497.23
Sqm
Rs.7,528.25
Sqm
Rs.7,617.90
Sqm
Rs.7,564.43
Sqm
Rs.7,397.62
Sqm
Rs.7,518.28
(i)6mm clear glass
Sqm
Rs.7,116.53
Sqm
Rs.7,147.54
Sqm
Rs.7,237.19
Sqm
Rs.7,582.41
Sqm
Rs.7,016.91
Sqm
Rs.7,137.58
(i)6mm clear glass
Sqm
Rs.6,647.53
Sqm
Rs.6,678.02
Sqm
Rs.6,766.16
Sqm
Rs.6,713.59
Sqm
Rs.6,549.59
Sqm
Rs.6,668.23
11.2.5 Providing, fitting and fixing coloured anodised aluminium sliding glazed doors with
anodised aluminium frames made of 100mm x 45mm x 2mm section of approved
brand with door style of size 81mm x 45mm x 2mm, top rails 55mm x 45mm x
2mm, lock rails 81mm x 45mm x 2mm, fitted with glazing clip, special type rubber
gasket complete including roller, tower bolt, aluminium door handle, lock, angles,
cleat etc. complete as specified and directed by the department at all levels.
11.2.6 Providing, fitting and fixing anodised aluminium sliding glazed doors with anodised
aluminium frames made of 100mm x 45mm x 2mm section of approved brand with
door style of size 81mm x 45mm x 2mm, top rails 55mm x 45mm x 2mm, lock rails
81mm x 45mm x 2mm, fitted with glazing clip, special type rubber gasket complete
including roller, tower bolt, aluminium door handle, lock, angles, cleat etc.
11.2.7 Providing, fitting and fixing coloured anodised aluminium framed double leaf glazed
doors with anodised aluminium frame made of 100mm x 45mm x 2mm sections of
approved brand with door styles of size 81mm x 45mm x 2mm, top rails 50mm x
45mm x 2mm, lock rails 81 mm x 45mm x 2mm,bottom rails 100mm x 45mm x
2mm fitted with glazing clip, special type rubber gasket complete including
angles, cleat etc complete as specified and directed by the Department at all levels.
Page-67
Description
Item
No.
11.2.8 Providing, fitting and fixing anodised aluminium framed double leaf glazed doors
with anodised aluminium frame made of 100mm x 45mm x 2mm section of
approved brands with door styles of size 81mm x 45mm x 2mm, top rails 50mm x
45mm x 2mm, lock rails 81 mm x 45mm x 2mm,bottom rails 100mm x 45mm x
2mm fitted with glazing clip, special type rubber gasket complete including
angles, cleat etc complete as specified and directed by the Department at all levels.
Unit
Rate
(i)6mm clear glass
Sqm
Rs.6,416.13
Sqm
Rs.6,446.62
Sqm
Rs.6,534.77
Sqm
Rs.6,482.19
Sqm
Rs.6,258.98
Sqm
Rs.6,377.62
Sqm
Sqm
Rs.7,616.42
Rs.7,428.10
(iii)5mm plain frosted glass
Sqm
Rs.7,513.88
(iv)6mm coloured glass
Sqm
Rs.7,606.44
(v) Prelaminated Board
Sqm
Rs.7,497.47
(vi) 5 mm clear glass
Sqm
Rs.7,316.56
(vii) 5 mm coloured glass
Sqm
Rs.7,449.83
(i)5mm thick frosted glass and 12mm thick prelaminated particle board
(ii)6mm clear glass
Sqm
Sqm
Rs.7,660.40
Rs.7,609.01
Sqm
Rs.7,641.02
Sqm
Rs.7,733.59

Sqm
Sqm
Rs.7,661.89
Rs.7,610.60
Sqm
Rs.7,721.20
11.2.9 Providing and fixing anodised aluminium framed double leaf doors of approved
brand with styles size 45mm x 48mm x 3.2mm, top rails 50mm x 45mm x 2.5mm,
lock rails 48 mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm fitted
with tapper clips of size 20mm x15mm x1.2mm complete with automatic floor
mounted door closure, butterfly type handles, special cylindrical lock, concealed
type aluminium tower bolt,neoprene dryset rubber gusket, door felt gusket,
etc.complete as directed by the Department at all levels.
(i)5mm thick frosted glass and 12mm thick prelaminated particle board
(ii)6mm clear glass
11.2.10 Providing and fixing anodised aluminium framed double leaf doors of approved
brand with styles size 45mm x 48mm x 3.2mm, top rails 50mm x 45mm x 2.5mm,
lock rails 48 mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm fitted
with tapper clips of size 20mm x15mm x1.2mm complete with automatic floor
mounted door closure, butterfly type handles, special cylindrical lock, concealed
type aluminium tower bolt,neoprene dryset rubber gusket, door felt gusket,
etc.complete as directed by the Department at all levels.
(a) Double leaf doors
11.2.11 Providing and fixing anodised aluminium framed single leaf door of approved brand
with styles size 45mm x 48mm x 3.2mm, top rails 50mm x 45mm x 2.5mm, lock
rails 48 mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm fitted with
tapper clips of size 20mmx15mmx1.2mm complete with automatic hydraulic floor
mounted door closure, butterfly type handles, special cylindrical locks, concealed
type tower bolt,neoprene dryset rubber gusket, etc.complete as directed by the
Department at all levels.
Page-68
Description
Item
No.
Unit
Rate
(i)5mm thick frosted glass and 12mm thick prelaminated board

(ii)6mm clear glass
Sqm
Sqm
Rs.7,260.59
Rs.7,050.29
Sqm
Rs.7,085.79
Sqm
Rs.7,188.41
Sqm
Rs.7,127.20
Sqm
Rs.6,936.27
Sqm
Rs.7,074.39
Sqm
Sqm
Rs.7,426.85
Rs.7,216.56
Sqm
Rs.7,252.06
Sqm
Rs.7,354.67

Sqm
Sqm
Rs.7,293.47
Rs.7,102.54
Sqm
Rs.7,203.13
11.2.12 Providing and fixing coloured anodised aluminium framed single leaf door of
approved brand with styles size 45mm x 48mm x 3.2mm, top rails 50mm x 45mm x
2.5mm, lock rails 48 mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm
fitted with tapper clips of size 20mm x 15mm x 1.2mm complete with automatic
hydraulic floor mounted door closure, butterfly type handles, special cylindrical
locks, concealed type tower bolt, neoprene dryset rubber gusket, etc.complete as
directed by the Department at all levels.
(i)5mm thick frosted glass and 12mm thick prelaminated board
(ii)6mm clear glass
11.3
MISCELLANEOUS
11.3.1 Suppling, fitting and fixing 20mm dia aluminium rod with aluminium bracket at
both ends of the pelmet over door and windows as directed and specified at all
levels.
Rs.115.44
(i) With angle of size 38mm x12 mm x 3mm
Rs.250.81
(ii) With angles of size 57mm x12 mm x 3mm
Rs.285.94
Rs.48.55
11.3.2 Providing and fixing aluminium step edging with anodised aluminium angle to stairs
at all levels.
11.3.3 Extra over item 11.3.2 for cutting R.C.C./brick steps for fixing of aluminium strip
edging and making good to match the surroundings.
11.4 PARTITION WALLS
11.4.1 Providing, fitting and fixing anodised aluminium partition walls of standard sections
of approved brand, joints mitred and welded (manufactured to relevant I.S.
specification) and providing and fitting angle cleat, rubber gasket, bolting device
screws etc. at all levels.
(i)Partly 6mm thick glass panes and 12mm prelaminated ply board
Sqm
Rs.3,429.01
(ii)6mm clear glass
Sqm
Rs.3,593.12
(iii)5mm frosted glass
Sqm
Rs.3,242.28
Sqm
Rs.3,345.88
Sqm
Rs.3,225.66
(v)Partly 5mm thick glass panes and 12mm prelaminated ply board
Sqm
Sqm
Rs.3,297.45
Rs.3,091.34
Sqm
Rs.3,230.77
Page-69
Description
Item
No.
11.4.2 Providing, fitting and fixing coloured anodised aluminium partition walls of
standard sections of approved brand, joints mitred and welded (manufactured to
relevant I.S. specification) and providing and fitting angle cleat, rubber gasket,
bolting device screws etc. at all levels.
Unit
Rate
(i)Partly 6mm thick glass panes and 12mm prelaminated ply board
(ii)6mm clear glass
Sqm
Sqm
Rs.3,586.86
Rs.3,364.29
Sqm
Rs.3,400.12
Sqm
Rs.3,503.72
Sqm
Rs.3,383.50
(vi)Partly 5mm thick glass panes and 12mm prelaminated ply board
Sqm
Rs.3,530.55
(viii) 5 mm clear glass
Sqm
Rs.3,249.18
(viii) 5 mm coloured glass
Sqm
Rs.3,388.61
(i)6mm clear glass
Sqm
Rs.3,581.54
Sqm
Rs.3,592.15
Sqm
Rs.3,619.62

Sqm
Sqm
Rs.3,685.73
Rs.3,551.02
Sqm
Rs.3,589.10
(i)6mm thick clear glass
Sqm
Rs.3,668.96
(ii)5mm thick frosted glass
Sqm
Rs.3,642.40
(iii)6mm thick coloured glass
Sqm
Rs.3,705.93
Sqm
Rs.3,772.04
(v) 5 mm thick clear glass
Sqm
Rs.3,638.44
(vi) 5 mm thick coloured glass
Sqm
Rs.3,675.41
Sqm
Rs.3,689.31
11.4.3 Providing, fitting and fixing anodised aluminium hollow section of approved brand
(Indal section 9210) of size 63.50mm x 38.10mm x 2.5mm thick for aluminium
frame partition wall, with a maximum spacing of frame 1.20m for
horizontal/vertical member including aluminium cleat 32mm x 50mm x 4mm thick
and fixing of pre-laminated board/ Nepal board/ Bhutan board with tapper cleat
20mm x 15mm x 1.2mm thick as directed by the department at all levels.
11.4.4 Providing, fitting and fixing coloured anodised aluminium hollow section of
approved brand (Indal section 9210) of size 63.50mm x 38.10mm x 2.5mm thick for
aluminium frame partition wall, with a maximum spacing of frame 1.20m for
and fixing of pre-laminated board/ Nepal board/ Bhutan board with tapper cleat
20mm x 15mm x 1.2mm thick as directed by the department at all levels.
11.5
PARTITION WALLS WITH DOORS
11.5.1 Providing, fitting and fixing anodised aluminium framed glazed doors with partition
walls partly glass and partly prelaminated board with anodised aluminium frame
made of 100mm x 43mm x 2mm sections of approved brand with doors style of
size 81mm x 43mm x 2mm, top rails 46mm x 43mm x 2mm, lock rails 81mm x
43mm x 2mm, fitting with glazing clip, special rubber type gusket complete
including hydraulic floor spring pivot aluminium door handle lock angles cleat etc.
complete as directed by the department at all levels.
(i)6mm thick glass panes and 12mm prelaminated board
Page-70
Description
Item
No.
Unit
Rate
(ii)6mm clear glass
Sqm
Rs.3,611.06
Sqm
Rs.3,638.42
Sqm
Rs.3,715.36

(vi) 5mm thick glass panes and 12mm prelaminated board
(vii) 5 mm clear glass
Sqm
Sqm
Sqm
Rs.3,668.19
Rs.3,624.59
Rs.3,521.02
Sqm
Rs.3,627.48
Sqm
Sqm
Rs.3,857.22
Rs.3,778.97
Sqm
Rs.3,806.33
Sqm
Rs.3,885.43
Sqm
Rs.3,838.25
(vi) 5 mm thick glass panes and 12mm prelaminated board
Sqm
Rs.3,846.47
Sqm
Rs.3,691.09
Sqm
Rs.3,797.54
(i)Partly 6mm thick coloured reflectory glass and partly with prelaminated board
Sqm
Rs.5,882.03
(ii)6mm clear glass
Sqm
Rs.4,488.98
Sqm
Rs.4,491.48
Sqm
Rs.4,646.02
Sqm
Rs.4,576.42
Sqm
Rs.4,359.33
Sqm
Rs.4,516.37
Sqm
Rs.6,103.98
(ii)6mm clear glass
Sqm
Rs.4,710.92
Sqm
Rs.4,751.28
(iv)6mm cloured glass
Sqm
Rs.4,867.96
11.5.2 Providing, fitting and fixing coloured anodised aluminium framed glazed doors with
partition walls partly glass and partly prelaminated board with anodised aluminium
frame made of 100mm x 43mm x 2mm sections of approved brand with doors style
of size 81mm x 43mm x 2mm, top rails 46mm x 43mm x 2mm, lock rails 81mm x
43mm x 2mm, fitting with glazing clip, special rubber type gasket complete
including hydraulic floor spring pivot aluminium door handle lock angles cleat etc.
complete as directed by the department at all levels.
(ii)6mm clear glass
11.5.3 Providing, fitting and fixing anodised aluminium framed sliding glazed doors with
partition walls with anodised aluminium frames made of 100mm x 43mm x 2mm
section of approved brand with door style of size 81mm x 43mm x 2mm, top rails
46mm x 43mm x 2mm, lock rails 81mm x 43mm x 2mm, paints and 12mm
prelaminated board fitting with glazing clip, special type rubber gasket complete
including roller, door handle, lock angles, cleat etc. complete as directed by the
department at all levels.
11.5.4 Providing, fitting and fixing coloured anodised aluminium framed sliding glazed
doors with partition walls with anodised aluminium frames made of 100mm x
43mm x 2mm section of approved brand with door style of size 81mm x 43mm x
2mm, top rails 46mm x 43mm x 2mm, lock rails 81mm x 43mm x 2mm, paints and
12mm prelaminated board fitting with glazing clip, special type rubber gasket
complete including roller, door handle, lock angles, cleat etc. complete as directed
by the department at all levels.
Page-71
Description
Item
No.
Unit
Rate
Sqm
Rs.4,798.37
Sqm
Rs.4,581.28
(vii) 5 mm cloured glass
Sqm
Rs.4,738.32
Sqm
Sqm
Rs.5,674.16
Rs.5,552.81
Sqm
Rs.5,592.42
Sqm
Rs.5,706.93
Sqm
Rs.5,638.63

Sqm
Sqm
Rs.5,582.85
Rs.5,425.58
Sqm
Rs.5,579.70
Sqm
Rs.5,893.12
(ii)6mm clear glass
Sqm
Rs.5,771.78
Sqm
Rs.5,811.39
Sqm
Rs.5,925.89
Sqm
Rs.5,857.60

Sqm
Sqm
Rs.5,801.82
Rs.5,644.55
Sqm
Rs.5,798.66
Sqm
Rs.3,718.46
Sqm
Rs.3,749.17
Sqm
Rs.3,837.94
Sqm
Rs.3,865.87
(v)12mm thick pre-laminated board and 5mm thick frosted glass panes
Sqm
Sqm
Rs.3,939.00
Rs.3,619.83
Sqm
Rs.3,739.30
11.5.5 Providing, fitting and fixing anodised aluminium framed double leaf glazed doors
with partition walls partly glazed and partly prelaminated board with anodised
aluminium frame made of 100mm x 43mm x 2mm sections of approved brand with
door styles of size 81mm x 43mm x 2mm, top rails 46mm x 43mm x 2mm, lock rails
81 mm x 43mm x 2mm fitting with glazing clips, special type rubber gasket
including hydraulic floor spring at all levels.
(i) 6mm thick glass panes and 12mm prelaminated board
(ii)6mm clear glass
11.5.6 Providing, fitting and fixing coloured anodised aluminium framed double leaf glazed
doors with partition walls partly glazed and partly prelaminated board with
anodised aluminium frame made of 100mm x 43mm x 2mm sections of approved
brand with door styles of size 81mm x 43mm x 2mm, top rails 46mm x 43mm x
2mm, lock rails 81mm x 43mm x 2mm fitting with glazing clips, special type rubber
gasket including hydraulic floor spring at all levels.
11.5.7 Providing, fitting and fixing anodised aluminium hollow section of approved brand
(Indal section 9210) of size 63.50mm x 38.10mm x 2.5mm thick for aluminium
frame partition wall, with a maximum spacing of frame 1.20m for
and fixing of glass panes and pre-laminated board with tapper cleat 20mm x 15mm
x 1.2mm thick fixing glass panes with rubber gusket, screws, etc. as directed by the
(i)6mm clear glass
Page-72
Description
Item
No.
11.5.8 Providing, fitting and fixing coloured anodised aluminium hollow section of
approved brand (Indal section 9210) of size 63.50mm x 38.10mm x 2.5mm thick for
aluminium frame partition wall, with a maximum spacing of frame 1.20m for
and fixing of glass panes and pre-laminated board with tapper cleat 20mm x 15mm
x 1.2mm thick fixing glass panes with rubber gusket, screws, etc. as directed by the
(i)6mm clear glass
Unit
Rate
Sqm
Rs.3,915.39
(ii)5mm plain frosted glass
Sqm
Rs.3,936.79
Sqm
Rs.3,998.62
Sqm
Rs.3,961.74
(v)12mm thick pre-laminated board and 5mm thick frosted glass panes
Sqm
Rs.3,936.79
Sqm
Rs.3,860.61
Sqm
Rs.3,943.83
Sqm
Rs.6,963.74
Sqm
Rs.7,419.93
(ii)6mm clear glass
Sqm
Rs.5,523.88
Sqm
Rs.5,561.51
Sqm
Rs.5,581.58
Sqm
Rs.5,932.14
Sqm
Rs.5,549.24
Sqm
Rs.5,643.86
Sqm
Rs.7,978.54
11.6 CURTAIN WALL, CURTAIN GLAZING, STRUCTURAL GLAZING

11.6.1 Providing, fitting and fixing aluminium curtain wall on the exterior face of building
fitting to concrete member by drilling hole fixing by brass screw fabricated with
anodised aluminium section of approved brand of size 101mm x 44.50mm by
providing aluminium jointing angles including providing 6mm thick coloured
reflectory type glass fitted with aluminium at all levels.
coloured anodised aluminium section of approved brand of size 101mm x 44.50mm
by providing aluminium jointing angles including providing 6mm thick coloured
reflectory type glass fitted with aluminium at all levels.
coloured anodised aluminium section of approved brand 101mm x 55mm x 2mm
by providing jointing angles including providing coloured reflectory type glass 6mm
thick fitted with aluminium at all levels.
anodised aluminium section of approved brand 101mm x 55mm x 2mm by
providing jointing angles including providing coloured reflectory type glass 6mm
thick fitted with aluminium at all levels.
11.6.5 Providing and fixing of aluminium curtain glazing made out of Anodised section of
approved shade section of 6 nos 1.2m each @ 1.819 Kg/m, 6 nos 1.2m each @
0.515 Kg/m, 6 nos 1.2m each @ 0.317 Kg/m of Jindal or equivalent complete with
rubber gasket and all other accessories, including fixing of 5mm tinted glass as and
where necessary.
I) Using Plain Anodised section
Page-73
Description
Item
No.
Unit
Rate
Sqm
Rs.8,337.78
Sqm
Rs.8,972.57
Sqm
Rs.9,394.97
(a) door Automatic ST10S
Each
Rs.98,881.98
(b) door Automatic ST10D
Each
Rs.112,615.59
(c) door Automatic ST20 S
Each
Rs.137,336.08
(d) door Automatic ST20 D
Each
Rs.168,923.38
(a) with 12 mm thick toughened glass
Sqm
Rs.10,891.60
(b) with 10 mm thick toughened glass
Sqm
Rs.11,098.68
(c) with 8 mm thick toughened glass
Sqm
Rs.10,650.63
(d) with 12 mm thick coloured glass
Sqm
Rs.10,846.71
(e) with 10 mm thick coloured glass
Sqm
Rs.10,891.60
(f) with 8 mm thick coloured glass
Sqm
Rs.10,650.63
II) Using Coloured Anodised section

11.6.6 Providing , fabrication and fixing of structural glazing made out of Anodised
aluminium mother frame 6 nos 1.2m each @ 1.819 Kg/m and subframe of 16 nos
0.60 m each @ 0.31 Kg/m of Jindal or equivalent and 5 mm reflective glass of
approved shade. The glass to be pasted using structural silicon (DC 995) and
weatherseal silicon to be used (DC 789), the structure complete with all accessories
as and where necessary.
11.6.7 Providing , fabrication and fixing of structural glazing made out of coloured
Anodised aluminium mother frame 6 nos 1.2m each @ 1.819 Kg/m and subframe
of 16 nos 0.60 m each @ 0.31 Kg/m of Jindal or equivalent and 5 mm reflective
glass of approved shade. The glass to be pasted using structural selicon (DC 995)
and weatherseal silicon to be used (DC 789), the structure complete with all
accessories as and where necessary.
11.7.1 Supplying,fitting and fixing of Automatic sliding door and operator, modular
design including internal cover with operator dimensions (H X T) not exceeding
120mm x 175mm and of length required to suit the opening size given below: Clear
opening of size 2400mm X 2400mm: compact linear sliding door automatic, with
self cleaning rollers, TUV type tested as per DIN 18650.The Automatic sliding door
consists of 16 bit Microprocessor Control unit, monitoring of closing force,
automatic reverse on contact with obstruction, operator commissioning without
any additional instrumentation and self-teaching. Operating Modes: Continuous
open, automatic operation, closing time, night lock, multi-sensor detector(radar
motion detector with direction detecion and self-monitoring, double 3D safeguard
light curtain (light barrier) for convenient safeguarding of the opening width) with
Electro magnetic locking, integrated in the drive unit, with manual emergency
unlocking of GODREJ/GEZE make.The operator will be provided with short circuit
proof power supply unit 220 / 240 V, 50 / 60 hz .
11.7.2 Providing, fitting and fixing anodised aluminuim framed glazed doors with anodised
aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size
88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm and bottom rails 100mm
x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete etc
Page-74
CH-12 PVC, uPVC, FRP DOORS & DOOR FRAMES

Item
No.
Unit
Rate
P.V.C. DOORS & DOOR FRAMES

12.1 Providing, fitting and fixing 40mm x 48mm wood reinforced PVC chowkhats fixed to
the columns / stiffeners / walls with necessary holdfast / sleeves etc. as specified
and directed at all levels.
Rm
186.12
a) 24mm thick
Sqm
999.44
b) 29mm thick
Sqm
1,511.53
Rm
700.79
Sqm
1,511.53
Sqm
1,947.01
12.2 Providing, fitting and fixing 24mm/ 29mm thick polymer reinforced moulded PVC
door shutters fixed to the chowkath with necessary hinges, screws, bolts etc. as
specified and directed at all levels (Door fixtures and fittings to be measured and
paid seperately)
12.3 Providing, fitting and fixing PVC door frame of Duroplast make DPF-5060 make
suitable for DPS-3720 made from extruded PVC multichamber hollow section
having dimensions of 50mmx60mm (Toletance + 1mm). Horizontal and vertical
sections shall be joined by steel screws after inserting M.S. tubular rectangular
galvanised L-shaped brackets of size 100mmx100mm or plastic brackets of size
75mmx75mm with metred cut at the corners. Hinge side of the frame shall be
reinforced with M.S.Tubular section of size 40mmx20mm. The frame will be fixed
to the column/ stiffner/ wall with the help of 3 nos 75mm long and 4mm dia steel
screws and expandable fastners on each side of the door frame complete in all
respects as sepcified and directed at all levels.
12.4 Providing, fitting and fixing PVC Door shutters of Duroplast DPS 3720 make made
fromm extruded PVC stiles and rails made from rigid PVC multicavity hollow
chamber section of size 90mmx37mm (Toletance+ 1mm). The corners of the stiles
and rails shall be metred out and fixed to each other with the help of solid plastic Lshaped brackets or M.S. rectangular tubular galvanised two nos of size
200mmx100mm and 100mmx100mm at each corner by self tapping steel screws.
PVC multicavity hollow section of size 105mmx37mm shall be fixed in the middle
by aluminium cleat and steel screws as lock rail. The section frame shall then be
filled with PVC panels of approved colour of size 100mmx20mm. Then two
numbers of bright steel rods of 6mm diameter shall be inserted horizontally
through stiles and panels with two numbers of checknuts and washers all complete
as specified and directed at all levels. (Door fixtures and fittings to be measured
and paid seperately)
12.5 Providing, fitting and fixing PVC Door shutters of 37mm (single panel seamless
finish) of Syntex make, at all levels made of extruded sections in the configuration
of 'A'.The overall dimension is 37mm x 90mm, with usual process variation having a
wall thickness of 2mm with a variation of +0.03mm provided with all plastic
reinforcement to avoid rusting. The shutter frame is mitred and joined at the
corners by means of stainless steel screws.The corners of the shutter frame are
being reinforced by polymeric reinforcement of the size 125mm x 250mm and the
lock rail is reinforced by 45 x18 x255 size reinforcement.
The lock rail is made of extruded hollow PVC section in the configuratino of 'H'
having wall thickness of 2mm with a variation of +0.03mm and effective dimension
of 37mm x 105mm. The infill is made of multi-chambered hollow PVC extruded
panel having an effective dimension of 762mm x 20mm or less as per requirement
with usual process variation having a wall thickness of 1mm +0.03mm.The entire
door shutter should be provided with S.S. screws at appropriate places for rust free
quality.
(Door fixtures and fittings to be measured and paid separately.)
Ch-12 : PVC/FRP Doors Door Frames
Page-75
Item
No.
12.6 Providing, fitting and fixing PVC Door shutters of 37mm (single panel seamless
finish) of Syntex make, at all levels made of extruded sections in the configuration
of 'A'.The overall dimension is 37mm x 90mm, with usual process variation having a
wall thickness of 2mm with a variation of +0.03mm provided with all plastic
reinforcement to avoid rusting. The shutter frame is mitred and joined at the
corners by means of stainless steel screws.The corners of the shutter frame are
being reinforced by polymeric reinforcement of the size 125mm x 250mm and the
lock rail is reinforced by 45 x18 x255 size reinforcement.The lock rail is made of
extruded hollow PVC section in the configuratino of 'H' having wall thickness of
2mm with a variation of +0.03mm and effective dimension of 37mm x 105mm.
Unit
Rate
Rm
209.70
12.7 FRP PANNELED DOOR Supplying & fixing of factory made 30mm thick Fibreglass
Reinforced Plastic (FRP) panneled door shutter of required colour of FIBREWAYS
made with fire retardant grade unsatured polyster resin,moulded to 3mm thick FRP
laminate for forming hollow rails and styles,with wooden frame and suitable blocks
of seasoned wood inside at required places for fixing of fittings,cast monolithically
with 5mm thick FRP laminate for panels and conforming to IS:14856-2000 including
fixing to frames complete as per direction of Engineer-in charge.
Sqm
2,647.85
12.8 FRP PANNELED DOOR Supplying & fixing of factory made 30mm thick Fibreglass
Reinforced Plastic (FRP) panneled door shutter of required colour of FIBREWAYS
made with fire retardant grade unsatured polyster resin,moulded to 3mm thick FRP
laminate for forming hollow rails and styles,with wooden frame and suitable blocks
of seasoned wood inside at required places for fixing of fittings,cast monolithically
with 5mm thick FRP laminate for panels and conforming to IS:14856-2000 including
fixing to frames complete as per direction of Engineer-in charge.
Sqm
3,047.82
12.9 FRP FRAME providing & fixing of factory made Fibreglass Reinforced Plastic (FRP)
door frame of FIBREWAYS having three legged of cross section 90mmx45mm
having single rebet of 32 mmx15mm to receive shutter of 30 mm thickness .The
laminate door frame moulded with fire retardant grade unsaturated polyster resin
and chopped mat .Door frame laminate and shall be filled with suitable wooden
block in all the three legs the frame shall be covered with covered glass from all
sides. MS stay shall be provided at the bottom to steady the frame.
Sqm
575.50
12.10 FRP SHEET MACHINE MADE supplying & fixing of factory Machine made
Fibreglass Reinforced Plastic (FRP) Translucent Roofing u/v stabilized sheets of
ROOFFIT in desired thickness ,size profile -(plain,corrugated,trapezoidal ) & colour
manufactured as per IS 12866 on continuous machine auto controlled production
line with auto batching,bubble free mixer,impregnation ,heating,refractor system
using continuous glass fibre roving of 2400 tex reinforced powder grade material as
per IS:11551 & sheet grade unsaturated polyester resin as per IS:6746 duly mixed
with u/v protection & extra clarity in continuous hot cured production translucent
pigmented or gelcoated opaque sheet complete as per specification,drawing or
direction of Engineer in charge.
Sqm
1,121.04
The infill is made of multi-chambered hollow PVC extruded panel having an

effective dimension of 762mm x 20mm or less as per requirement with usual
process variation having a wall thickness of 1mm +0.03mm.The entire door shutter
should be provided with S.S. screws at appropriate places for rust free quality.
(Door fixtures and fittings to be measured and paid separately.)
Page-76
Item
No.
12.11 FRP CHAJJA providing & fixing of factory made Fibreglass Reinforced Plastic (FRP)
chajja 4 mm thick of FIBREWAYS in required colour size and design made by Resin
Transfer Moulding (RTM) Machine Technology, resulting in void free compact
laminate in single piece ,having smooth gradual slope curvature for easy drainage
of water and duly reinforced by two numbers vertically and one number
horizontally 50x2mm thick M.S. plate with 12 mm in built hole for grouting on the
existing wall along with the 50 mm flange duly inserted and sealed in the wall
complete in one single piece casted monlythically including all necessary fittinga.
?The FRP chajja should be manufactured using unsaturated polyster resin as per IS
6746 duly reinforced with fibre glasss chopped strand mat (CSM)as per IS: 11551
complete with protective Gelcoat U/V coating on top for completen resistance
from the extreme of temperature,weather & sunlight.
Unit
Rate
Rm
4,795.82
sqm
6,272.22
sqm
5,431.37
uPVC Doors & Windows

uPVC Windows
12.12 Fixed Windows
12.12.1 Supplying and installing uPVC- Fixed Windows made out of Lead free green profile
having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall
thickness 2.4mm with corners fusion welded, fully reinforced with galvanized steel
1.5/2mm including glazing bead , grooving bead, drain cap, fisher screws, packing
pieces, necessary stainless steel screws etc. complete as directed. The windows
must be installed complete with all kinds of ironmongery including EPDM gaskets,
bridging wedges and glass packers and with suitable water draining system.
Application of Silicon sealant from inside / outside of dowcorning / GE or
equivalent.
With 5mm clear glass
(a) Fixed window using uPVC sections of size 58mm x 52mm x 2.4mm thick wall for
frame and 58mm x 68mm having 2.4mm thick wall for glass sash having
reinforcement of 1.5mm thick in both frame & sash.
(WINSTA KOMMERLING/ FINESTA/ ENCRAFT)
(b) ProVent fixe window Using uPVC sections of size 37mm x 43mm x 2.2mm thick
wall for frame and 37mm x 56mm x 2.2mm thick wall for sash having 1.5mm thick
reinforcement for both frame & sash.
12.12.2 Supplying and installing uPVC- Sliding Windows made out of Lead free green
profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of
wall thickness 2.4mm with corners fusion welded, fully reinforced with Galvanized
steel 1.5/2mm including interlock profile, glazing bead, grooving bead, brush seal,
aluminum sliding track, stainless steel rollers, sealing wedge block, Espag, int
handle, pop up handle, keeper, drain cap, fisher screws, packing pieces with all
necessary stainlessness screws etc. complete as directed. The windows must be
installed complete with all kinds of ironmongery including EPDM gaskets, bridging
wedges and glass packers and with suitable water draining system. Application of
silicon sealant from inside / outside of Dowcorning / GE or equivalent.
With 5mm clear glass
(a) 2 Track Sliding Window with Flyscreen using uPVC section of sizes 88mm x 50
mm x 2.4mm thick wall for frame with inbuilt flyscreen track, 37mm x 61mm x
2.4mm thick wall for glass sash, 25mm x 49mm x 2.4mm thick wall for flyscreen
sash having 1.5mm thick reinforcement, Interlock: 43mm x 23mm (Glass Panel)
Page-77
Item
No.
Unit
Rate
(i) 2-Panel with 5mm clear float glass
sqm
8,854.83
(ii) 4-Panel with 5mm clear float glass
sqm
10,116.09
(i) 2-Panel with 5mm clear float glass
sqm
8,194.16
(ii) 4-Panel with 5mm clear float glass
sqm
9,515.49
a) Single leaf Side hung Window using uPVC section of size 58mm x 57mm x
2.4mm thick wall for frame, 58mm x 68mm x 2.4mm thick wall for glass sash.
With 5mm clear float glass
sqm
10,716.71
b) Double leaf Side hung Window with a fixed Mullion (2 Panels) using uPVC
profile size of 58mm x 57mm x 2.4mm thick wall for frame, 58mm x 68mm x
2.4mm thick wall for glass sash, 58mm x 74mm x 2.4mm thick for mullion.
sqm
10,716.71
(c) Double leaf Side hung Window with a Dummy Mullion - French Window (2
Panels) using uPVC section of size 58mm x 57mm x 2.4mm thick wall for frame,
58mm x 68mm x 2.4mm thick wall for glass sash
sqm
10,956.95
(d) Single leaf Top hung Window using uPVC section of size 58mm x 57mm x
2.4mm thick wall for frame, 58mm x 68mm x 2.4mm thick wall for glass sash
sqm
9,815.80
(e) Double leaf Top hung Window using uPVC section of size of 58mm x 57mm x
2.4mm thick wall for frame, 58mm x 68mm x 2.4mm thick wall for glass sash,
58mm x 74mm x 2.4mm thick wall for mullion.
sqm
11,077.07
(f) ProVent openable Top hung Window using uPVC section of size 37mm x 43mm
x 2.2mm thick wall for frame, 37mm x 56mm x 2.2mm thick wall for glass sash
sqm
8,013.98
(b) 2 Track Sliding Window without Flyscreen using uPVC section of size 58mm x
53mm x 2.4mm thick wall for frame, 37mm x 61mm x 2.4mm thick wall for glass
sash having 1.5mm thick reinforecement for both frame & sash, Interlock: 43mm x
23mm (Glass Panel)
12.12.3 Supplying and installing uPVC- Casement Windows made out of Lead free green
profile having "GREENLINE" mark of BIS standard uPVC sections of wall thickness
2.4mm, multichambered with corners fusion welded, fully reinforced with
Galvanized steel 1.5/2mm including glazing bead, folding gasket, glazing gasket,
friction stay, Espag handle, Espag, keeper, drain cap, run up block, fisher screws,
packing pieces with all stainless steel screws complete as directed. The windows
must be installed complete with all kinds of ironmongery including EPDM
gaskets,bridging wedges and glass packers and with suitable water draining system.
Fittings ROTO / GQ or Equivalent. Application of Silicon sealant from Inside /
Outside of Dowcorning / GE or equivalent.
12.13 uPVC DOORS
Page-78
Item
No.
12.13.1 Supplying and installing uPVC- sliding door made out of Lead free green profile
having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall
thickness 2.8mm with corners fusion welded, fully reinforced with Galvanized steel
2mm including interlock profile, glazing bead, grooving bead, brush seal, locking
arrangement, aluminum sliding track, stainless steel rollers, sealing wedge block,
Espag, int handle, pop up handle, keeper, drain cap, fisher screws, packing pieces
with all necessary stainlessness screws etc. complete as directed. The windows
bridging wedges and glass packers and with suitable water draining system. Fittings
ROTO / GQ or Equivalent. Application of silicon sealant from inside / outside of
Dowcorning / GE or equivalent.
Unit
Rate
(I) 2 Track Sliding door with Flyscreen using uPVC section of size 88mm x 50mm x
2.8mm thick wall for frame, 37mm x 75mm x 2.8mm thick wall for glass sash,
25mm x 49mm x 2.8mm thick wall for flyscreen sash, Interlock: 43mm x 23mm
(Glass Panel)
(a) 2-Panel
i) Using 5mm clear float glass
sqm
11,857.86
ii) Using 5mm clear toughened glass
sqm
10,956.95
i) Using 5mm clear float glass
sqm
12,638.64
sqm
12,638.64
i) Using 5mm clear glass
sqm
10,956.95
sqm
8,794.77
sqm
10,776.77
sqm
11,077.07
sqm
15,281.32
(b) 4-Panel
(II) 2 Track Sliding door without Flyscreen using uPVC section of size 58mm x
53mm x 2.8mm thick wall for frame, 37mm x 75mm x 2.8mm thick wall for glass
sash, Interlock: 43mm x 23mm (Glass Panel)
(a) 2-Panel
(b) 4-Panel
12.13.2 Supplying and installing uPVC- Casement Door made out of Lead free green profile
having "GREENLINE" mark of BIS standard uPVC sections of wall thickness 2.4mm,
multichambered with corners fusion welded, fully reinforced with Galvanized steel
1.5/2mm including glazing bead, folding gasket, glazing gasket, locking
arrangement, Espag handle, Espag, keeper, drain cap, run up block, fisher screws,
packing pieces with all stainless steel screws complete as directed. The windows
bridging wedges and glass packers and with suitable water draining system. Fittings
ROTO / GQ or Equivalent. Application of Silicon sealant from Inside / Outside of
Dowcorning / GE or equivalent.
(a) Single leaf Side hung Door using uPVC section of size 58mm x 69mm x 2.4mm
thick wall for frame, 58mm x 109mm x 2.4mm thick wall for glass sash, Aluminium
threshold at bottom
Page-79
Item
No.
Unit
Rate
sqm
9,875.86
sqm
19,125.20
sqm
26,933.09
(b) Double leaf Side hung Door with a Dummy Mullion - French Door using uPVC
section of size 58mm x 69mm x 2.4mm thick wall for frame, 58mm x 109mm x
2.4mm thick wall for glass sash, 58mm x 61mm x 2.4mm thick wall for dummy
mulion, Aluminium threshold at bottom.
12.14 Lift and Slide Patio Door
12.14.1 Supplying and installing uPVC- lift or slide patio door made out of Lead free green
profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of
wall thickness 2.8mm with corners fusion welded, fully reinforced with Galvanized
steel 2mm including interlock profile, glazing bead, grooving bead, brush seal,
locking arrangement, aluminum sliding track, stainless steel rollers, sealing wedge
block, fisher screws, packing pieces with all necessary stainlessness screws etc.
complete as directed. The windows must be installed complete with all kinds of
ironmongery including EPDM gaskets, bridging wedges and glass packers and with
suitable water draining system. Fittings ROTO / GQ or Equivalent. Application of
silicon sealant from inside / outside of Dowcorning / GE or equivalent.
uPVC section of size 174mm x 70mm x 2.8mm thick wall for frame, 62mm x
100mm x 2.8mm thick wall for glass sash.
Page-80
CH-13: PAINTING
Item
No.
13.1
Description
Unit
Rate
WHITE / CHALK WASHING
13.1.1 SURFACE PREPARATION

13.1.1 (a) Removing white or colour wash by steel wire brushing and/ or scraping, sand
papering and preparing the wall surface smooth including necessary repairs to
scratches complete.
Sqm
Rs.13.57
b) Extra over item no (a) above for scraping on ceiling and on sloping roof.
Sqm
Rs.1.36
c) Washing and cleaning wall surface with soap, soda and clean water
Sqm
Rs.3.72
d) Extra over item no (c) above for washing and cleaning ceiling and sloping roof.
Sqm
Rs.0.37
(a) White washing with lime on wall surfaces (two coats) to give an even shade
including throughly brooming the surface to remove all dirt, dust,mortar drops and
other foreign matter.
Sqm
Rs.17.56
(b) White washing with lime on old wall surfaces (one coat) to give an even shade
including throughly brooming the surface to remove all dirt, dust,mortar drops and
other foreign matter.
Sqm
Rs.9.06
(c) Extra over item no. (a) above for every subsequent coat of white washing with
lime on wall surfaces.
Sqm
Rs.8.51
(d) Extra over item no. (a) above for white washing with lime on ceiling and on
sloping roof.
Sqm
Rs.0.94
e) Extra over item no. (b) above for white washing with lime on ceiling and on
sloping roof.
Sqm
Rs.0.70
(a) White washing with chalk on cloth or hessian ceiling (two coats) to give an even
shade including throughly brooming the surface to remove all dirt, dust, mortar
drops and other foreign matter.
Sqm
Rs.12.77
b) Extra over item no. (a) above for every subsequent coat of white washing with
chalk washing on cloth or hessian cloth ceiling.
13.2.1 COLOUR WASHING / CEMENT WASHING / DISTEMPERING
Sqm
Rs.5.76
a) Colour washing with lime on wall surface (two coats) over and including a
priming coat of white washing to give an even shade after throughly brooming the
surface to remove all dirt, dust, mortar drops and other foreign matter.
Sqm
Rs.27.93
b) Extra over item no. (a) above for every subsequent coat of colour wash with lime
on wall surfaces.
Sqm
Rs.10.53
c) Cement washing with portland cement slurry on wall surface (one coats) to give
a smooth bodied opaque finish including throughly brooming the surface to
remove all dirt, dust, mortar drops and other foreign matter.
Sqm
Rs.7.74
13.2.2 a) Removing dry or oil bound distemper by washing and scraping and sand papering
the wall surface smooth including necessary repairs to scratches complete.
Sqm
Rs.7.64
b) Extra over item no (a) above for removing dry or oil bound distemper on ceiling
and in sloping roof.
Sqm
Rs.0.76
13.1.2 WHITE WASHING
13.1.3
CHALK WASHING
13.2.2 DISTEMPERING
Ch13 : Painting Works
Page-81
Item
No.
Description
Unit
Rate
c) Applying one coat of distemper primer of approved brand and manufacture on

wall surface after throughly brushing the surfaces free from mortar droppings and
other foreign matter and including preparing the surface even and sand papered
smooth.
Sqm
Rs.35.17
d) Applying one coat of alkali resistance primer of approved brand and

manufacture on wall surface after throughly brushing the surfaces free from
mortar droppings and other foreign matter and including preparing the surface
even and sand papered smooth.
Sqm
Rs.35.17
e) Extra over item no. (c) and (d) above for applying one coat of distemper
primer/alkali resistant primer over ceiling and on sloping roof.
Sqm
Rs.1.60
f) Distempering with dry distemper of approved brand and manufacture(two

coats)and of required shade on new wall surface to give an even shade, over and
including priming coat of white primer after throughly brushing the surface
free from mortar dropings and other foreign matter and including preparing
surface even and sand papered smooth.
Sqm
Rs.78.37
g) Distempering with dry distemper of approved brand and manufacture (twocoats)

and of required shade on new wall surface to give an even shade,after throughly
brushing the surface free from mortar dropings and other foreign matter and
including preparing surface even and sand papered smooth.
Sqm
Rs.51.46
h). Distempering with dry distemper of approved brand and manufacture(one coat)
and of required shade on old wall surface to give an even shade,after throughly
brushing the surface clean of all grease, dirt, loose pieces of scales including
preparing surface even and sand papered smooth.
i). Extra over item no (f), (g) and (h) above for distempering every subsequent coat
of distempering with dry distemper of approved brand and manufacture.
Sqm
Rs.29.14
Sqm
Rs.29.14
j). Extra over item no. (f) above for distempering with dry distemper on ceiling and
or sloping roof.
k) Extra over item no. (g) above for distempering with dry distemper on ceiling and
or sloping roof.
l) Extra over item no. (h) above for distempering with dry distemper on ceiling and
or sloping roof.
m) Distempering two coats with oil bound distemper of approved brand and
manufacture and of required shade on new wall surface to give an even shade, over
and including a priming coat with distemper primer of approved brand and
manufacture after throughly brooming the surface free from mortar dropings and
other foreign matter and including preparing surface even and sand papered
smooth.
(i).Priming coat with distemper primer
Sqm
Rs.4.93
Sqm
Rs.3.23
Sqm
Rs.1.69
Sqm
Rs.34.56
(ii). Top coat
Sqm
Rs.48.68
(i).Priming coat with alkali resistant primer
Sqm
Rs.34.56
(ii). Top coat
Sqm
Rs.48.68
(n) Distempering two coats with oil bound distemper of approved brand and
manufacture and of required shade on new wall surface to give an even shade, over
and including a priming coat with alkali resistant primer of approved brand and
manufacture after throughly brooming the surface free from mortar dropings and
other foreign matter and also including preparing the surface even and sand
papered smooth.
Page-82
Item
No.
Description
Unit
(o) Distempering (one coat) with oil bound distemper of approved brand and
manufacture and of required shade on old wall surface to give an even shade, after
throughly brooming the surface free from dirt, loose scales and other foreign
matter and also including preparing the surface even and sand papered smooth.
Sqm
Rs.27.81
p) Extra over item no (m), (n) and (o) above for every subsequent coat of
distempering with oil bound distemper of approved brand and manufacture.
Sqm
Rs.25.88
q) Extra over item no (m), (n) above for distempering with oil bound distemper of
approved brand and manufacture on celing and sloping roof.
Sqm
Rs.4.93
r) Extra over item no (o) above for distempering with oil bound distemper of
approved brand and manufacture on celing and sloping roof.
Sqm
Rs.3.23
a) Applying one coat of cement primer of approved brand and manufacture on new
wall surface after throughly brooming the surfaces free from mortar droppings and
smooth.
Sqm
Rs.40.66
b) Finishing wall with water proofing cement paint of approved brand and
manufacture and of required shade on new wall surface (two coats) to give an even
shade after throughly brooming the surfaces to remove all dirt and remains of
loose powdered materials.
Sqm
Rs.46.75
c) Finishing wall with water proofing cement paint of approved brand and
manufacture and of required shade on old wall surface (one coats) to give an even
shade after throughly brooming the surfaces to remove all dirt and remains of
loose or softened paint.
Sqm
Rs.26.24
d) Extra over item no. (b) and (c) above for every subsequent coat of water proofing
cement paint of approved brand and manufactured.
e) Extra over item no (b) above for finishing with cement paint on celing and
sloping roof.
Sqm
Rs.21.24
Sqm
Rs.4.93
f) Extra over item no (c) above for finishing with cement paint on celing and sloping
roof.
Sqm
Rs.3.23
(g) Extra over item no (d) above for finishing with cement paint on celing and
sloping roof.
Sqm
Rs.1.69
13.3.1 Providing surface preparation for walls, celling etc.using average 1.50 mm thick
plaster of paris including clearing, rubbing with sand paper, filling gaps, depression
etc. where necessary, with chalk powder and and plaster of paris paste, making the
surface even and smooth complete at all levels as specified and directed.
Sqm
Rs.60.63
13.3.2 Providing two coats of acrylic water based wall putty/ wall filler of Asian Paints/
Berger/ Dulux over concrete/ cement plaster/ brick walls and ceilings both internal
and external after removing all the loosely adhering material from the wall/ ceiling
surface with the help of emery stone, putty blade or wire brush, moistening the
wall with the help of sufficient quantity of clear water as specified and directed by
the department.
Sqm
Rs.52.10
13.3.3 Applying water miscible dry powder based 1.5mm thick Vinyl wall putty of Seacem
Paint (I) Pvt. Ltd. based on white cement and reinforced with vinyl resin specially
designed self curing use as plaster over sand cement plastering over brick and
cement concrete wall, ceilings and other surfaces for both interior and exterior
surfaces to provide a firm and durable base for subsequent painting.
Sqm
Rs.52.60
13.2.3
13.3
Rate
CEMENT PAINT & PRIMER
PLASTER OF PARIS & WALL PUTTY
Page-83
Item
No.
Description
Unit
Rate
13.3.4 Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement
based putty for concrete/ mortar walls and ceiling both internal and external) after
removing all loosely adhering material from the wall surface with the help of emery
stone, putty blade or wire brush and moistening the wall with sufficient quantity of
clean water as specified and directed by the department. (Total thickness of two
coats is maximum 1.5mm)
(i) Thickness = 1.5 mm thick
Sqm
Rs.66.60
(ii)Thickness = 1.0mm thick
Sqm
Rs.50.20
Sqm
Rs.50.30
Sqm
Rs.71.17
Sqm
Rs.49.82
Sqm
Rs.41.67
Sqm
Rs.29.17
(i).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger
paint/ ICI paint/ J & N paint/ Nerolac)
Extra over item no 13.4.3 above for painting with acrylic emulsion paint of
approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/
Nerolac) on celling and on sloping roof.
Sqm
Rs.4.95
Sqm
Rs.3.23
13.3.5 Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/
mortar walls and ceiling both internal and external) after removing all loosely
adhering material from the wall surface with the help of emery stone, putty blade
or wire brush and moistening the wall with sufficient quantity of clean water as
specified and directed by the department. (Total thickness of two coats is
maximum 1.5mm)
WALL PAINTING
13.4
13.4.1 Wall painting (two coats) with acrylic emulsion paint approved brand and
manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new
surface to give an even shade after throughly brushing the surfaces free from
mortar droppings and other foreign matter and sand papered smooth.
(a).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger
13.4.2 Extra over item no 13.4.1 above for every subsequent coat of wall painting with
acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger
paint/ ICI paint/ J & N paint/ Nerolac).
13.4.3 Wall painting (one coat) with acrylic emulsion paint approved brand and
manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on old wall
(a). Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger
13.4.4 Extra over item no 13.4.3 above for every subsequent coat of wall painting with
acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger
13.4.5 Extra over item no 13.4.1 above for painting with acrylic emulsion paint of
13.4.6
Page-84
Item
No.
13.4.7
Description
Sqm
Rs.76.99
Sqm
Rs.53.89
(a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger
Extra over item no 13.4.9 above for every subsequent coat of wall painting with
Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger
Sqm
Rs.45.26
(i).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger
Sqm
Rs.31.68
Sqm
Rs.4.93
Sqm
Rs.3.23
Extra over item no 13.4.7 above for every subsequent coat of wall painting with
Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger
13.4.9
13.4.10
13.4.11
Wall painting (One coat) with Plastic Emulsion Paint approved brand and
manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on old wall
Extra over item no 13.4.7 above for painting with Plastic emulsion paint of
13.4.12
Rate
Wall painting (two coats) with Plastic emulsion paint of approved brand and
manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new
(a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger
13.4.8
Unit
Extra over item no 13.4.9 above for painting with Plastic emulsion paint of
13.5
EXTERIOR PAINTS / COATINGS
13.5.1
Applying one self-priming coat of acrylic emulsion coating of Unicem "Rakshak"

brand by thinning 1ltrs of paints with 1ltrs of water over freshly plastered wall
surface after throughly brooming the surfaces free from mortar droppings and
smooth as specified and directed by the department.
Sqm
Rs.52.66
13.5.2
Finishing wall with two coats of acrylic emulsion exterior coatings of Unicem
"Rakshak" brand of required shade by thinning 1ltr. of paint with 750ml of water to
give an even shade after throughly brooming the surfaces to remove all dirt and
remains of loose powdered materials as specified and directed by the department.
Sqm
Rs.85.77
13.5.3
Extra over item no.13.5.2 above for every subsequent coat of acrylic emulsion
exterior coatings of Unicem 'Rakshak' brand of required shade.
Sqm
Rs.42.38
13.5.4
Applying one self-priming coat of Unicem "Shakti" brand of required shade over
freshly plastered wall surface after throughly brooming the surfaces free from
mortar droppings and other foreign matter and including preparing the surface
even and sand papered smooth as specified and directed by the department.
Sqm
Rs.36.81
Page-85
Item
No.
Description
Unit
13.5.5
Finishing wall with two coats of waterproofing cement coatings of Unicem "Shakti"
brand of required shade by thinning 1 part of paint with 1 part of water to give an
even shade after throughly brooming the surfaces to remove all dirt and remains of
loose powdered materials as specified and directed by the department.
Sqm
Rs.46.78
13.5.6
Extra over item no.13.5.5 above for every subsequent coat of waterproofing
cement coatings of Unicem 'Shakti' brand of required shade.
Sqm
Rs.27.86
13.5.7
Extra over item no.13.5.2 and 13.5.5 above for applying / finishing on celing and
sloping roof.
Sqm
Rs.6.89
13.6.1 Removing old paint or polish from wood and wood base surfaces with paint
remover of approved brand and manufacture and making the surface even.
Sqm
Rs.49.30
13.6.2 Removing old paint or polish from wood and wood base surfaces with caustic
soda solution and making the surface even
13.6.3 Applying priming coat over new wood and wood based surfaces over 100mm in
girth/width after and including preparing the surface by throughly cleaning oil,
grease, dirt snd other foreign matter , sand papering and knotting.
Sqm
Rs.36.40
(a). With ready mixed paint , Wood primer (pink)
Sqm
Rs.36.90
(b). With ready mixed paint , wood primer (white).
Sqm
Rs.36.90
(c). With ready mixed paint , Alluminium primer
Sqm
Rs.30.16
(a). With ready mixed paint , wood primer (pink)
Rm
Rs.3.95
(b). With ready mixed paint , wood primer (white).
Rm
Rs.3.95
(c). With ready mixed paint , Alluminium primer .
Rm
Rs.3.23
a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).
Sqm
Rs.61.95
b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).
Sqm
Rs.73.00
Rm
Rs.7.00
Rm
Rs.8.25
Sqm
Rs.41.26
Sqm
Rs.47.78
13.6
Rate
PAINTING ON WOOD AND WOOD WOOD BASED SURFACES
13.6.4 Applying priming coat over new wood based surfaces up to 100mm in girth/width
after and including preparing the surface by throughly cleaning oil, grease, dirt and
other foreign matter , sand papering and knotting.
13.6.5
Painting two coats (excluding priming coat) on new wood and wood based surface
with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/
ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the
surfaces of all dirt, dust and other foreign matter sand papering and stopping.
(i).Surfaces over 100mm in width or girth.
(ii).Surfaces up to 100mm in width or girth.
13.6.6 Painting one coat (excluding priming coat) on old wood and wood based surfaces
with enamel paint to give an even shade including cleaning the surface of all dirt,
dust and other foreign matter sand papering and stopping.

Page-86
Item
No.
Description
Unit
Rate
Rm
Rs.4.42
Rm
Rs.5.13
Sqm
Rs.36.90
Sqm
Rs.43.47
Rm
Rs.4.17
Rm
Rs.4.92
Sqm
Rs.42.07
Sqm
Rs.44.82
Sqm
Rs.33.96
Rm
Rs.3.80
Sqm
Rs.61.95
Sqm
Rs.73.00
Rm
Rs.7.00
Rm
Rs.8.25
13.6.7 Extra over item no13.6.5and 13.6..6 for every subsequent coat of paint.
13.7
PAINTING ON STEEL AND OTHER METAL SURFACE
13.7.1 Synthetic enamel paint, aluminium paint / bituminus paint on steel and other metal
surfeces.
i).Removing old paint from steel and other metal surface and making the surface
even.
a). With hand scraping
b). With paint remover
13.7.2 Applying primary coat over new steel and other metal surface over 100m in width
or girth after preparing the surface by throughly cleaning oil,grease, dirt and other
foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand
paper.
a). With ready mixed "red-lead/ red oxide" primer.
13.7.3 Applying primary coat over new steel and other metal surface upto 100m in width
or girth after preparing the surface by throughly cleaning oil,grease, dirt and other
foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand
paper.
a). With ready mixed "red-lead/ red oxide" primer.
13.7.4 Painting two coats (excluding priming coat) on new steel and other metal surface
with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/
ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface
of all dirt, dust and other foreign matter.
13.7.5 Painting one coat (excluding priming coat) on previously painted steel and other
metal surface with enamel paint of approved brand and manufacture(Asian paint/
Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including
cleaning the surface of all dirt, dust and other foreign matter.
Page-87
Item
No.
Description
Unit
Rate
Sqm
Rs.41.26
Sqm
Rs.47.89
Rm
Rs.4.66
Rm
Rs.5.41
Sqm
Rs.36.90
Sqm
Rs.43.11
Rm
Rs.4.17
Rm
Rs.4.92
(a).Surfaces over 100mm in width or girth.
Sqm
Rs.60.44
(b).Surfaces up to 100mm in width or girth.
Rm
Rs.6.83
(a).Surfaces over 100mm in width or girth.
Sqm
Rs.38.84
(b).Surfaces up to 100mm in width or girth.
Rm
Rs.4.39
13.7.9 Painting three coats (excluding priming coat) on new steel and other metal
surface with ready mixed bituminous paint of approved brand and manufacture
(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) after applying black
anticorrosive paint to give an even shade including cleaning the surface of all
dirt, dust and other foreign matter.
Sqm
Rs.47.76
13.7.10 Painting one coats (excluding priming coat) on new steel and other metal surface
with ready mixed bituminous paint of approved brand and manufacture(Asian
paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) after applying black
anticorrosive paint to give an even shade including cleaning the surface of all
Sqm
Rs.24.41
M2
Rs.26.51
Sqm
Rs.55.87
13.7.6 Extra over item no.13.7.4 and 13.7.5 for every subsequent coat of paint.
13.7.7 Painting two coats (excluding priming coat) on new steel and other metal surface
with alluminium paint of approved brand and manufacture(Asian paint/ Berger
paint/ ICI paint/ J & N paint/ Nerolac) and brushing to give an even shade including
13.7.8 Painting one coats (excluding priming coat) on new steel and other metal surface
with alluminium paint of approved brand and manufacture(Asian paint/ Berger
paint/ ICI paint/ J & N paint/ Nerolac) and brushing to give an even shade including
13.8
PAINTING ON ROOF SURFACES
13.8.1 Applying mordent solution of approved brand and manufacture on new C.I sheet
for preparation of surfaces for painting @5.00 litre/100 sq. metre of surface and
rubbing the solution with brush including thoroughly cleaning the surface of oil,
grease, dirt and other foreign matter.
13.8.2 Painting two coats on new G.C.I sheets with ready mixed anticorrosive paint of
approved brand and shade suitable for painting over G.C.I sheets to give an even
shade including the cleaning the rust patches with emery paper, dust ,dirt, grease
and other foreign matter with water complete.
Page-88
Item
No.
Description
13.8.3 Painting one coats on old G.C.I sheets with ready mixed anticorrosive paint of
approved brand and shade suitable for painting over G.C.I sheets to give an even
shade including the cleaning the rust patches with emery paper, dust ,dirt, grease
and other foreign matter with water complete.
Unit
Sqm
13.8.4 Extra over item no.13.8.3 for every subsequent coat of paint.
Rate
Rs.42.27
Rs.19.12
SPECIAL WATHER PROOF COLOURING

13.9.1 Finishing old / new wall with water proofing weather coat smooth anti-fungal
exterior painting of approved make of Berger paint of required shade after cleaning
and clearing the surface etc. including scaffolding complete as directed at all levels
(two coats)
Sqm
Rs.127.80
13.9.2 Finishing old/ new wall with water proofing weather coat smooth anti-fungal
exterior painting of Apex brand of Asian Paints and of required shade after cleaning
and clearing the surface etc. including scaffolding complete as directed at all levels
(two coats)
Sqm
Rs.127.58
premium textured exterior finish of Sandex Matt brand of Snowcem India Ltd. of
required shade after clering and clearing the surfaces etc.including scaffolding
complete as directed at all levels (two coats).
Sqm
Rs.142.93
premium acrylic smooth exterior finish of Snowcryl XT brand of Snowcem India Ltd.
of required shade after clering and clearing the surfaces etc. including scaffolding
complete as directed at all levels (two coats).
Sqm
Rs.129.21
13.9.5 Finishing wall with water proofing weather coat smooth anti-fungal exterior
painting of Ace brand of Asian Paints and of required shade on old/new wall
surface after cleaning and clearing the surface etc. including scaffolding complete
as directed at all levels (two coats)
Sqm
Rs.101.78
13.9.6 Finishing old/new wall with water proofing weather coat smooth anti-fungal
exterior painting of approved make of Dulux (ICI) paint of required shade after
cleaning and clearing the surface etc. including scaffolding complete as directed at
all levels (two coats)
Sqm
Rs.127.80
13.9.7 Supplying and applying interior/exterior walls/ floors/ roofs one coat of Epoxy
Primer of Jenson & Nicholson/ Nerolac brand as priming coat after cleaning and
clearing the surfaces as specified and directed and then applying two coats of
Epoxy paints of Jenson & Nicholson/ Nerolac brand of required shade on walls/
floors/ roof surfaces as specified and directed complete including scaffolding at all
levels.
Sqm
Rs.224.27
exterior painting of Nerolac Paints Limited of required shade on old/ new wall
surface to give an even shade after cleaning and clearing the surface etc. including
scaffolding complete as directed at all levels (two coats).
Sqm
Rs.127.80
13.10.1
Providing and applying Spectrum aggragate textured wall coating in the branded
name of SPECTRUM with its all tools, plants and machineries and scaffolding etc. as
per manufacturers guideline and specification of the product.
a)Spectrum Antonio
Sqm
Rs.652.52
13.10.2
a)Spectrum Granito naturale
Sqm
Rs.769.21
Page-89
Item
No.
Description
Unit
13.10.3
a)Spectrum Naturaplast
Sqm
Rs.800.27
13.10.4
a)Spectrum Permastone
Sqm
Rs.799.10
13.10.5
a)Spectrum Granula
Sqm
Rs.707.21
13.10.6
a)Spectrum Perlina (Regular)
Sqm
Rs.748.60
13.10.7
a)Spectrum Resana
Sqm
Rs.254.56
13.10.8
a)Spectrum Star Spray
Sqm
Rs.399.56
13.10.9
a)Spectrum Quartz King
Sqm
Rs.204.11
13.10.10 Providing and applying Spectrum aggragate textured wall coating in the branded
a)Spectrum Spray Coat
Sqm
Rs.637.99
a)Spectrum Random Star
Sqm
Rs.719.14
a)Spectrum Super fine
Sqm
Rs.306.16
Rate
Page-90
Item
No.
Description
Unit
Rate
a)Spectrum Permasan
Sqm
Rs.716.48
a)Spectrum Ornaplast
Sqm
Rs.642.14
a)Spectrum Graniplast
Sqm
Rs.713.30
a)Spectrum Classic
Sqm
Rs.212.58
a)Spectrum Perlina ( fine )
Sqm
Rs.593.43
a)Spectrum Rustik ( fine )
Sqm
Rs.593.43
a)Spectrum Rustik (Regular)
Sqm
Rs.787.39
Page-91
CH-14: VARNISHING, POLISHING, OILING

Item
No.
Unit
Rate
14.1 VARNISHING
14.1.1 Varnishing two coats (excluding priming coat) on new wood and wood based
surfaces under coating with flatting varnish and finishing coat with copal varnish
or spar varnish to give an even surface including cleaning the surface of all
dirt,dust and filling the knots,crack etc with specially made wood putty and sand
papering so as to produce a smooth,dry and matt surface.
(i) Surfaces over 100mm in width or girth.
Sqm
Rs.83.47
(ii) Surfaces upto 100mm in width or girth.
Rm
Rs.7.71
(i) Surfaces over 100mm in width or girth.
Sqm
Rs.41.96
(ii) Surfaces upto 100mm in width or girth.
Sqm
Rs.4.08
14.2.1 Polishing with french sprit polishing on new wood and wood based surfaces to
give an even surface including cleaning the surface of all dirt, dust sand papered
smooth and including a coat of wood filter
Sqm
Rs.115.21
14.2.2 Polishing with french sprit polishing on previously polished wood and wood based
surfaces to give an even surface including cleaning the surface of all dirt,dust, sand
papered smooth and including a coat of wood filter
Sqm
Rs.62.39
Sqm
Rs.62.88
Sqm
Rs.35.37
Sqm
Rs.20.12
Sqm
Rs.19.69
Sqm
Rs.25.46
Sqm
Rs.15.90
14.1.2 Varnishing one coat (excluding priming coat) on previously varnished wood and
wood based surfaces with copal/ spar varnish to give an even surface including
cleaning the surface of all dirt, dust and sand papering so as to produce a papering
so as to produce a smooth,dry and matt surface.
14.2 POLISHING
14.2.3 Applying wax-polish on new wood and wood based surfaces with bees wax polish in
prop. (2 bees wax: 1.5 linseed oil:1 terpentine oil:0.5 varnish by weight to give an
even surface including cleaning the surface of all dirt,dust, sand papered smooth .
14.2.4 Applying wax-polish on previously wax polish wood and wood based surfaces with
bees wax polish in prop. (2 bees wax:1.5 linseed oil:1 terpentine oil: 0.5 varnish by
weight) to give an even surface including cleaning the surface of all dirt,dust, sand
papered smooth .
14.2.5 Applying wax-polish on new concrete/masonry floor with wax polish of approved
brand and manufacture to give an even surface including cleaning the surface of all
dirt,dust and other foreign matter.
14.2.6 Applying wax-polish on previously polished concrete/ masonry floor with wax
polish of approved brand and manufacture to give an even surface including
cleaning the surface of all dirt,dust and other foreign matter .
14.3 OILING
14.3.1 Applying two coats of oil with raw linseed oil on new wood and wood based surface
including cleaning the surface of all dirt,dust and sand papered so as to produce a
smooth, dry and neat surface.
14.3.2 Applying one coat of oil with raw linseed oil on previously oiled wood and wood
based surfaces to give an even surface including cleaning the surface of all dirt,dust
and sand papering so as to produce a smooth, dry and neat surface.
Ch-14 : Vernishing, Polishing, Oiling
Page-92
Item
No.
Unit
Rate
14.3.3 Applying two coats of wood preservative on wood and wood based surfaces
including preparing the surface by throughly cleaning oil, grease dirt and other
foreign matter, sand papering and knotting.
(a) With kiricide oil
Sqm
Rs.24.59
(b) With Creosote oil
Sqm
Rs.25.35
(a) With kiricide oil
Sqm
Rs.19.43
(b) With Creosote oil
Sqm
Rs.20.04
Sqm
Rs.44.15
Sqm
Rs.24.79
Sqm
Rs.105.17
Sqm
Rs.60.38
14.3.4 Applying one coat of wood preservative on previously created wood and wood
based surfaces, including preparing the surface by throughly cleaning oil, grease
dirt and other foreign matter, sand papering and knotting.
14.3.5 Painting two coats (excluding priming coat) on new wood and wood based surface
with coal tar, new wood and wood based surface with coal tar, black paint to give
an even surface including cleaning all dirt, dust and other foreign matter.
14.3.6 Painting one coat (excluding priming coat) on previously painted wood and wood
based surfaces with coaltar,black paint to give an even surface including cleaning all
14.3.7 Applying two coats of wood preservative oil,colourless (Burger Products) on new
wood and wood based surfaces, after including preparing the surface by throughly
cleaning oil,grease,dirt and other foreign matter, sand papering and knotting.
14.3.8 Applying one coats of wood preservative oil,colourless (Burger Products) on new
wood and wood based surfaces, after including perparing wood based surfaces,
after including perparing the surface by throughly cleaning oil,grease,dirt and
other foreign matter, sand papering and knotting.
Ch-14 : Vernishing, Polishing, Oiling
Page-93
CH-15: DOOR AND WINDOW FITTINGS

Item
No.
15.1
Unit
Rate
ELECTRO COLOURED IRON FITTINGS
15.1.1 Supplying, fitting, fixing electrocoloured iron fittings of approved make, resonably
smooth, free from sharp edges and corners, flaws and other defects and with
counter sunk holes for wood screws including necessary screws etc. complete.
a) Sliding door bolts
i) 300mm x 16mm
Each
Rs. 169.88
ii) 250mm x 16mm
Each
Rs. 152.04
i) 300mm x 10mm
Each
Rs. 164.68
ii) 250mm x 10mm
Each
Rs. 139.71
iii) 200mm x 10mm
Each
Rs. 121.86
iv) 150mm x 10mm
Each
Rs. 92.12
v) 100mm x 10mm
Each
Rs. 64.78
i) 75mm
Each
Rs. 29.35
ii) 100mm
Each
Rs. 35.30
iii) 150mm
Each
Rs. 41.24
i) 75mm
Each
Rs. 32.91
ii) 100mm
Each
Rs. 38.86
iii) 150mm
Each
Rs. 43.62
i) 75mm
Each
Rs. 8.53
ii) 100mm
Each
Rs. 10.32
iii) 150mm
Each
Rs. 13.29
iv) 250mm
Each
Rs. 21.02
v) 300mm
Each
Rs. 37.67
i) 90mm / 75mm
Each
Rs. 70.85
ii) 115mm
Each
Rs. 76.80
iii) 150mm
Each
Rs. 100.58
i) 50mm x 40mm x 2.5mm
Pair
Rs. 63.47
ii) 75mm x 60mm x 3.15
Pair
Rs. 82.51
Pair
Rs. 44.45
ii) 75mm x 47mm x 1.60mm
Pair
Rs. 58.72
iii) 100mm x 58mm x 1.90mm
Pair
Rs. 76.56
b) Tower bolts
c) Cast iron stove door handles
d) MS door handles
e) MS gate shutter hook & eye
f) MS wire hasp and staples
g) MS butt hinge
I) Heavy type
II) Medium type
III) Light type

Ch-15 : Door and widow Fittings
Page-94
Item
No.
Unit
Rate
i) 50mm x 30mm x 0.90mm
Pair
Rs. 36.12
Pair
Rs. 44.45
Pair
Rs. 61.10
i) 75mm ( 100mm x20mm x2.24mm )
Pair
Rs. 183.61
ii) 100mm (125mm x 27mm x 2.80mm)
Pair
Rs. 232.37
ii) 125mm (125mm x 27mm x 2.80mm)
Pair
Rs. 296.61
a) 100mm
Pair
Rs. 332.29
b) 125mm
Pair
Rs. 367.97
c) 150mm
Pair
Rs. 504.76
RM
Rs. 206.33
i) 300mm x 20mm x 6mm
Each
Rs. 128.09
ii) 250mm x 10mm x 6mm
Each
Rs. 107.87
l) MS mortice night latches
Each
Rs. 1,064.67
i) 100mm
Each
Rs. 740.82
ii) 125mm
Each
Rs. 788.40
iii) 150mm
Each
Rs. 835.98
i) 300mm x 16mm
Each
Rs. 272.17
ii) 250mm x 16mm
Each
Rs. 260.27
i) 300mm x 12mm
Each
Rs. 140.90
ii) 250mm x 12mm
Each
Rs. 121.86
iii) 200mm x 12mm
Each
Rs. 104.02
iv) 150mm x 10mm
Each
Rs. 88.56
v) 100mm x 10mm
Each
Rs. 68.34
i) 75mm
Each
Rs. 36.49
ii) 100mm
Each
Rs. 38.86
iii) 150mm
Each
Rs. 42.43
I) 100mm
Each
Rs. 22.22
ii) 125mm
Each
Rs. 24.59
h) MS pariamentary hinge
i) MS double acting spring hinge
j) MS continuous hinge
35mm x 1.00m
k) MS door latches
m) MS rim latches
15.2
ALUMINIUM FITTINGS
15.2.1 Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably
smooth, free from sharp edges and corners, flaws and other defects and with
counter sunk holes for screws including necessary aluminium screws etc.
complete.( anodised to bright natural matt & satin finished )
b) Tower bolts
c) Door handles
d) Gate shutter hook & eye
Page-95
Item
No.
Unit
Rate
iii) 150mm
Each
Rs. 26.97
iv) 250mm
Each
Rs. 44.81
v) 300mm
Each
Rs. 60.27
Pair
Rs. 65.86
Pair
Rs. 77.75
iii) 75mm x 65mm x 4mm
Pair
Rs. 87.26
iv) 100mm x 63mm x 3.2mm
Pair
Rs. 99.15
v) 100mm x 75mm x 4mm
Pair
Rs. 107.48
i) 75mm ( 100mm x31mm x6.5mm )
Pair
Rs. 161.01
ii) 100mm (50mm x 22.5mm x 6.5mm)
Pair
Rs. 195.51
RM
Rs. 182.54
e) Butt hinge
f) Pariamentary hinge
g) Continuous piano hinge

40mm x .8m
h) Mortice night latches
Rs. 1,307.99
i) Rim latches
i) 100mm
Each
Rs. 871.66
ii) 125mm
Each
Rs. 954.92
iii) 150mm
Each
Rs. 1,050.08
j) Fan light pivot
Each
Rs. 56.85
k) Fan light catcher
Each
Rs. 82.23
l) Hydraulic door closure
Each
Rs. 1,077.24
i) 65mm( Godrej With handle(2 lever)
set
Rs. 1,076.05
ii) 75mm(Godrej with handle(4 lever)
set
Rs. 1,288.96
iii) 100mm(Godrej with handle (6 lever)
set
Rs. 1,652.92
iv) Aldrop with In built Lock-6 lever kadi tala(Godrej Make)
set
Rs. 1,026.08
m) Mortice lock vertical type
v) pin cylinder Mortise Lock Oliver/Matiz/Victoria -Godrej make
Rs. 2,213.14
n) Drawer locks
i) 40mm
Each
Rs. 184.49
ii) 50mm
Each
Rs. 204.72
iii) 65mm
Each
Rs. 246.34
iv) 75mm
Each
Rs. 252.29
i) 40mm
Each
Rs. 177.36
ii) 50mm
Each
Rs. 192.82
iii) 65mm
Each
Rs. 210.66
iv) 75mm
Each
Rs. 246.34
p) Finger plate
Each
Rs. 324.88
q) Kicking plate
Each
Rs. 327.79
o) Cupboard locks
r) Curtain rod
Page-96
Item
No.
15.3
Unit
Rate
i) 20mm x 2mm
RM
Rs. 117.91
ii) 25mm x 2mm
RM
Rs. 147.65
s) Wardrobe knob
Each
Rs. 41.26
t) Door stopper with rubber stopper
Each
Rs. 85.81
i) 300mm x 16mm
Each
Rs. 824.08
ii) 250mm x 16mm
Each
Rs. 764.59
i) 300mm x 10mm
Each
Rs. 376.41
ii) 250mm x 10mm
Each
Rs. 271.74
iii) 200mm x 10mm
Each
Rs. 236.04
iv) 150mm x 10mm
Each
Rs. 212.25
v) 100mm x 10mm
Each
Rs. 146.84
i) 75mm
Each
Rs. 59.08
ii) 100mm
Each
Rs. 65.03
iii) 150mm
Each
Rs. 82.87
I) 100mm
Each
Rs. 44.81
ii) 150mm
Each
Rs. 55.51
iii)250mm
Each
Rs. 62.65
iv) 300mm
Each
Rs. 72.16
Pair
Rs. 448.02
iii) 100mm x 50mm x 4mm
Pair
Rs. 329.08
Pair
Rs. 293.40
iv) 75mm x 50mm x 4mm
Pair
Rs. 274.37
v) 75mm x 40mm x 2.5mm
Pair
Rs. 195.87
vi) 50mm x 40mm x 2mm
Pair
Rs. 82.87
i) 75mm ( 75mm x20mm x 3.2mm )
Pair
Rs. 472.64
ii) 100mm (100mm x 27mm x 5mm)
Pair
Rs. 660.57
ii) 150mm (100mm x 27mm x 5mm)
Pair
Rs. 815.19
i) 90mm
Pair
Rs. 199.30
ii) 115mm
Pair
Rs. 211.19
iii) 150mm
Pair
Rs. 246.88
BRASS FITTINGS
15.3.1 Supplying, fitting, fixing brass fittings of approved make, resonably smooth, free
from sharp edges and corners, flaws and other defects and with counter sunk holes
for screws including necessary c.p. brass screws etc. complete.( bright natural matt
& satin finished ).
b) Tower bolts
c) Door handles
D) Gate shutter hook & eye
e) Butt hinge
f) Pariamentary hinge
g) Hasp and staple
Page-97
Item
No.
Unit
Rate
h) Spring hinge
i) 100mm
Pair
Rs. 951.34
ii) 125mm
Pair
Rs. 1,040.55
iii) 150mm
Pair
Rs. 1,165.44
Each
Rs. 369.54
Each
Rs. 226.81
iii) 100mm x 20mm x4mm
Each
Rs. 161.39
Each
Rs. 248.22
Each
Rs. 236.33
i) Mortice night latches (Godrej make)
Each
Rs. 980.91
ii. Rim latches (Godrej make)
Each
Rs. 1,254.65
l) Fan light pivot
Each
Rs. 53.70
m) Fan light catcher
Each
Rs. 103.65
i) 65mm
set
Rs. 791.76
ii) 75mm
set
Rs. 1,362.69
Each
Rs. 1,323.44
i) 40mm
Each
Rs. 285.07
ii) 50mm
Each
Rs. 332.64
iii) 65mm
Each
Rs. 386.17
iv) 75mm
Each
Rs. 439.69
i) 40mm
Each
Rs. 232.07
ii) 50mm
Each
Rs. 279.64
iii) 65mm
Each
Rs. 333.17
iv) 75mm
Each
Rs. 386.69
r) Finger plate
Each
Rs. 446.21
s) Kicking plate
Each
Rs. 256.44
i) 20mm x 2mm
RM
Rs. 239.24
ii) 25mm x 2mm
RM
Rs. 310.61
u) Wardrobe knob
Each
Rs. 72.18
v) Door stopper with rubber stopper
Each
Rs. 176.85
w) Ball catcher
Each
Rs. 50.76
x) Magnet catcher
Each
Rs. 50.76
y) Peeping plate
Each
Rs. 167.18
i) Flush bolts
j) Door latches
k) Night latches
n) Mortice lockl vertical type
o) Mortice cylindrical type(Godrej make)-polished Brass

p) Drawer locks
q) Cupboard locks
t) Curtain rod
15.4
DOOR CLOSER & FLOOR SPRING
Page-98
Item
No.
15.4.1 Providing,fitting and fixing Door closer of various type UL listed and fire rated good
quality depending on the door specification.Types like single speed,Double
Speed,Heavy Duty etc are available and as directed & specified by the department.
Unit
Rate
A) Godrej
a) Single Speed Door Closer( size166.5x 48mmx 67mm)-Model C071
Each
Rs. 1,163.92
b) Double Speed Door Closer( size 140mm x 39mm x 60mm)- Model Number C 752
Each
Rs. 1,447.02
c) Heavy Duty Door Closer( size 180 mm x 65mm x 64mm)
Each
Rs. 1,938.25
d) Sleek Door Closer( 215mm x 51mm x 45mm)
Each
Rs. 1,700.37
e) Concealed Door Closer ( 230mm x 76.5mm x 30.5mm)

B) Fire Rated Door Closer-EN rated Godrej Make
Each
Rs. 3,990.03
a) Single speed Door Closer _ Model LKYGDC680
Each
Rs. 3,014.69
b) Double speed Fire Rated Door Closer Model LKYGDC834

c) Fire rated Track Arm Door Closer Model LKYGDC610
Each
Each
Rs. 4,304.05
Rs. 4,910.65
a) Compact Floor spring B710 ( size 274mm x 97mm x 40mm)
Each
Rs. 4,709.90
b) Heavy duty Floor Spring D100 ( size 308mm x 108mm x40.5mm)
Each
Rs. 5,604.36
Each
Rs. 7,829.80
i) Gold line and silver line
RM
Rs. 1,151.17
ii) Starline and pearline
RM
Rs. 1,033.42
iii) Club line
RM
Rs. 1,745.88
iv) Print line
RM
Rs. 1,508.00
v) Wood line
RM
Rs. 1,543.68
vi) Silk line
RM
Rs. 1,745.88
vii) Nature line
RM
Rs. 2,221.66
viii) Studio line
RM
Rs. 1,389.06
ix) Soft line
RM
Rs. 1,022.70
x) Fine line
RM
Rs. 1,056.01
xi) Speer line
RM
Rs. 794.34
xii) Sleek line
RM
Rs. 413.71
15.4.2 Providing,fitting and fixing Floor Spring of various weight & type UL listed and fire
rated good quality depending on the door specification.Types like single
speed,Double Speed,Heavy Duty etc are available and as directed & specified by the
department
A) Architectural Range
B) Godrej
15.5
a) Fire rated floor spring B 803( size 307mm x 109mm x 40mm)- 80 kg door/ B 804(
size 307mm x 109mm x 40mm)-100 kg door (Godrej make)
DRAPERY ROD
15.5.1 Supplying, fitting and fixing drapery rods along with all accessories in doors,
windows and other openings complete as specified and directed by the
departmentb at all levels.
(A) MAC Drapery rod
Page-99
Item
No.
Unit
Rate
(B) VISTA Drapery rod

i) Vista sherwood
RM
Rs. 1,032.23
ii) Florence III vista
RM
Rs. 1,435.44
iii) Flerona (Rotiron)
RM
Rs. 1,091.69
iv) Flored colour gold (pulling system)
RM
Rs. 1,239.18
v) Flored color color (Pulling system)
RM
Rs. 1,239.18
vi) Soffio M-IV
RM
Rs. 913.29
vii) Soffio M-II
RM
Rs. 675.39
(C) PVC coated Drapery rod
RM
Rs. 592.13
(D) Mettalic Drapery rod
RM
Rs. 1,151.17
i) Bellini
RM
Rs. 2,554.70
ii) Renoir Pyramid
RM
Rs. 2,371.53
iii) Renoir Tulip
RM
Rs. 2,601.09
iv) Renoir Orchid
RM
Rs. 3,515.76
v) Lorenzo
RM
Rs. 2,417.91
vi) Monet Oyestar
RM
Rs. 2,784.26
vii) Monet Tulip
RM
Rs. 3,515.76
i) Angelo
RM
Rs. 2,096.76
ii) Salvador
RM
Rs. 2,096.76
iii) Van Gough
RM
Rs. 1,778.00
iv) Picaso
RM
Rs. 1,594.82
i) 100 mm
Sqm
Rs. 1,861.25
ii) 89 mm
Sqm
Rs. 1,914.78
iii) 75 mm
Sqm
Rs. 2,009.94
iv) 50 mm
Sqm
Rs. 2,150.29
i) 100 mm
Sqm
Rs. 1,914.78
ii) 89 mm
Sqm
Rs. 2,043.25
iii) 75 mm
Sqm
Rs. 2,151.48
iv) 50 mm
Sqm
Rs. 2,340.61
i) 15mm micro blind
Sqm
Rs. 1,745.88
ii) 25 mm slim line blind
Sqm
Rs. 1,805.35
iii) 25 mm perforated blind
Sqm
Rs. 2,090.82
(D) Mettalic Drapery rod

(E) Globus Collection -23mm
(F) Globus Collection -19mm
15.6 BLIND
15.6.1 Supplying, fitting and fixing MAC blinds horizontal and vertical complete as
specified and directed by the department at all levels.
(A) Vertical blinds
(a) Regular
(b) Blackout
(B) Horizontal blinds
Page-100
Item
No.
Unit
Rate
iv) 25 mm printed blind
Sqm
Rs. 2,697.44
v) 25 mm dust guard blind
Sqm
Rs. 4,541.06
vi) 25 mm pearl finish blind
Sqm
Rs. 5,373.66
vii) 25 mm special effect blind
Sqm
Rs. 2,865.14
viii) 25 mm timber blind
Sqm
Rs. 5,549.69
i) Square
Sqm
Rs. 330.46
ii) Round
Sqm
Rs. 372.08
15.6.2 Extra for providing 175 mm x 175 mm size Vision panel in door shutters including
providing and fixing 4 mm thick clear glass and teak wood beading 12mm x 12mm ,
all along the glass edges on both sides including necessary screws etc. and painting
/ polishing of wooden beading complete as directed.
Page-101
CH-16: GLASS FITTINGS

Item
No.
16
GLASS FITTING
16.1 Providing and fixing clear sheet glass beded in putty and fixed with/without
wooden bidding including necessary cutting and glass to be required sized(payment
for wooden bead shall be made separately)
Unit
Rate
(1). Area of glass panes not exceeding 0.15m2

(c). 3.00mm thick.
Sqm
Rs.486.11
(a). 3.00mm thick.
Sqm
Rs.447.30
(b). 4.00mm thick.
Sqm
Rs.562.01
(c). 5.00mm thick.
Sqm
Rs.642.09
Sqm
Rs.691.60
(a). 3.00mm thick.
Sqm
Rs.600.17
(b). 3.50mm thick.
Sqm
Rs.676.25
(a). 3.50mm thick.
Sqm
Rs.726.19
(b). 4.00mm thick.
Sqm
Rs.671.34
(c). 5.00mm thick.
Sqm
Rs.811.36
Sqm
Rs.858.64
(i). Area of glass panes not exceeding 0.15m2
Sqm
Rs.428.49
(ii). Area of glass panes exceeding 0.15m2 but not exceeding 0.52m2.
Sqm
Rs.444.67
(iii). 3.00mm thick.
Sqm
Rs.433.90
(iv). 4.00mm thick.
Sqm
Rs.554.31
(v). 5.00mm thick.
Sqm
Rs.632.84
(i). 3.00mm thick.
Sqm
Rs.433.90
(ii). 4.00mm thick.
Sqm
Rs.554.31
(2). Area of glass panes exceeding 0.15m2 but not exceeding 0.52m2.
(3). Area of glass panes exceeding 0.52m2.

(a). 5.00mm thick.
16.2 Providing and fixing plain frosted glass of ordinary glazing quality beded in putty
and fixed with/without wooden bidding including necessary cutting and glass to be
required sized(payment for woodenbead shall be made separately)
(1). Area of glass panes not exceeding 0.15m2
(2). Area of glass panes exceeding 0.15m2 but not exceeding 0.52m2.
(3). Area of glass panes exceeding 0.52m2.

(a). 5.00mm thick.
16.3 Providing and fixing pin-headed glass 3mm thick beded in putty and fixed
with/without wooden bidding including necessary cutting and glass to be required
sized(payment for wooden bead shall be made separately)
16.4 Providing and fixing plain with special metal, sachputty and glazing clip in steel
window / doors / cleastory windows including necessary cutting to required sized
for all floors.
(1). Clear sheet glass panes
(b) Frosted Glass panes.
Ch-16; Glass fittings
Page-102
CHAPTER 17: FENCING & GATES

Item
no
Description
Unit
Rate
Sqm
Rs.188.50
a) Single
Sqm
Rs.115.24
b) Double
17.1 Spilt jati bamboo Zenana fencing up to 1800 mm high with well matured Bhaluka
bamboo post1500 mm to 1800mm apart driven at least 600 mm under ground and
three lines of double bamboo kami tied with wire or cane (spilt bamboo woven in 4
nos of bamboo kamies)
17.2 Jati bamboo compound Zeora fencing 1050mm to 1200mm high kamies of sizes
30mmx6mm placed not more than 100mm apart and driven at least 100 mm under
groundincluding Bhaluka bamboo post 1500 to 1800mm apart driven at least
450mm under ground and tied with three lines of double longitudinal bamboo
kamies and half bamboo on top (Lattice pattern).
Sqm
Rs.154.92
17.3 Bhaluka bamboo dressed post 75mm to 100mm dia driven at least 600mm under
ground and tied with wire or cane (in zenana fencing)
Each
Rs.85.11
17.4 Bhaluka bamboo dressed post 75mm to 100mm dia driven at least 450mm under
ground and tied with wire or cane (in zeora fencing)
Each
Rs.56.74
17.5 Providing barbed wire on the existing barbed wire fencing with seven strands of
barbed wire 12 S.W. G.x 2pliesx 4 points at 75mm apart including supplying, fitting
and fixing with galvanised staples 38mm x 38mm x 3mm sizes with existing posts of
the fencing, including removing rotten barbed wire as directed, complete with
strengthening of post and tightening of the old barbed wire and joinining old
serviceable pieces on remaining lines as and where necessary and as directed.
Rs.28.08
17.6 Supplying , fitting and fixing barbed wire fencing with seven strands of barbed wire
12 S.W.G.x 2pliesx 4 points at 75mm apart including supplying fitting and fixing
sawn sal wood posts of 100mmx100mm size struts 1800mm long at 1500mm apart
driven at least 600mm under ground with providing 100mmx75mm size struts
1800mm long in corner, straining and end post as necessary including coaltaring
two coats in posts and struts and supplying necessary nails, staples etc.complete as
directed and specified (the distribution of the barbed wire should be placed at
equal intervals for the intermediate except bottom and top which is to be placed at
100mm and 230mm clearance respectively).
Rs.1,096.24
17.7 Supplying , fitting and fixing galvanised barbed wire fencing with seven strands of
barbed wire 12 S. W. G .x 2plies x 4 points at 75mm apart with angle iron
intermediate fencing posts not more than 1800mm apart and straining and end
post etc. as necessary to be fitted with straining eye bolts and staples etc.complete
as directed, specification of the angle iron post as given below.
Rs.630.70
a) Intermediate post 35mm x35mm x5mm x1800mm long bottom torched and duly
slotted.
b) Straining post 65mm x 65mm x 6mm x 1820mm long with 2 stays of
35mmx35mmx1520mm long and 3 base plates 200mm x 200mm x 5mm, duly
slotted to take eye bolts etc.
c) Corner posts 65mm x 65mm x 6mm x1820mm long with 2 stays of 35mm x
35mm x 5mm x 1 670 mm and 3 base plates 200mm x 200mm x 5mm,duly slotted
to take eye bolts etc.
d) Straining or end posts 65mmx 65mm x 6mmx 1820mm long with 1 stays of
35mm x 35mm x 5mmx 1820 mm long with base plates 200mmx 200mm x 5mm,
duly slotted to take eye bolts etc.
Ch-17 : Fencing and Gates
Page-103
Item
no
Description
Unit
Rate
(All the angle iron posts to be embeded 600mm in C.C.pillars of size

300mmx300mmx600mm in prop.1: 3: 6 and one coat of anticorrosive ready
mixed painting to all iron works) including excavation of foundation trenches for
C.C. blocks and refilling and removal of surplus soil after completion of works.
17.8 Supplying, fitting and fixing goat proof wire fencing 1070mm high with horizontal
wire spacing at 130 mm, 130mm, 150mm, 150mm, 180mm and 180mm from
bottom onwards and vertical wires at 100mm apart top and bottom wires should
be of 8 S.W G. and intermediate and vertical wire should be of 10S.W.G.with
angle iron posts specified in item no 17.7 above including supplying, fitting and
fixing with necessary straining eye bolts and staples etc. and painting one coat to
all iron posts etc. with anti-corrosive black paint etc. complete as directed and
specified(intermediate and straining post should be placed not more than 4000mm
and not less than 3000 mm apart and all posts embedded in C.C. pillars of size
300mm x 300mm x 600mm in prop 1:3:6).
Rs.530.42
17.9 Supplying, fitting and fixing goat proof wire fencing 1200mm high with horizontal
wire spacing at 100mm, 100mm, 100mm, 100mm, 100mm, 100mm,150mm,
150mm, 150mm and 150mm from bottom onwards and vertical wires at 130mm
apart, first 3 horizontal wires from top barbed wire apart, first 3 horizontal wires
from top barbed wire 12 S.W G.x 2 plies x 4 points x 100 mm apart bottom wire 10
S.W.G. fitted with angle iron posts specified in item no.17.7 above including
supplying, fitting and fixing with necessary hooks, bolts and staples etc. and
painting one coat to all iron posts etc. with anti-corrosive black paint etc.
complete as directed and specified(intermediate and straining post should be
placed not more than 4000 mm and not less than 3000 mm apart and all posts
embedded in C.C. pillars of size 300mm x 300mm x 600mm in prop 1:3:6).
Rs.530.42
17.10 Supplying, fitting and fixing chain link fencing of 10 S.W.G, G.I. Wire 50mm x50mm
mesh fitted to M.S angle iron post at 2000mm apart of specification detailed below
including supplying, fitting and fixing hooks, eye bolts with nuts, staples and bolts
including three horizontal lines of G.I wire 10 S.W.G at top,middle and bottom and
with one vertical line to each fencing post for keeping the fencing tight and erect
complete, including one coat of primer painting to M.S angle iron post in P.C.C base
etc. with following.
Sqm
Rs.656.82
a) Corner and end posts with M.S angle of size 50mmx50mmx 5mm and length not
less than 1800mm only duly slotted and bottom torqued with two numbers as stay
posts..
b). Intermediate post with M.S angle of size 40mmx40mmx5mm and length not less
than 1800mm only duly slotted and bottom torqued and splayed.
c).Stay post with M.S angle of size 35 mmx35mmx5mm and length not less than
1800mm duly slotted and bottom torqued and splayed. All M.S angle iron posts are
to be fitted to P.C.C base embedded not less than 600mm (P.C.C. work shall be
Page-104
Item
no
Description
Unit
Rate
17.11 Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from
50mm x 6mm M.S. flat iron with another horizontal flat at the middle, 20mm dia
M.S bars at 200mm apart from bottom flat to top flat and 20 mm dia M.S. bars at
200mm apart from bottom flat to middle flat including drilling, welding etc.
complete. All vertical bars are to be protruded at least 100mm above the middle
and top flat is to be flattended and pointed as directed. Necessary locking
arrangement on both faces, arrangement for temporary closing the gate and 2
nos.( minium) strong iron hinges of M.S bars and flat of same sizes on each leaf to
be embeded in C.C brick pillars as necessary including a red oxide painting to all
iron works as directed and specified. (Separate payment will be made for posts).
Qtl
Rs.7,436.57
17.12 Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from
40mm x 40mm x 6mm M.S. angle and with M.S. flat of 40mm x 6mm size as per
approved design.Necessary locking arrangement for temporary closing the gate
and 2nos.( minimum) strong iron hinges of M.S bars and flat of same sizes on each
leaf to be embedded in C.C brick pillers as necessary including a red oxide painting
to all iron works as directed and specified.(Separate payment will be made for
posts).
Qtl
Rs.6,808.23
17.13 Providing rails for plying of rollers of gate made made from 50mm x 6mm size M.S.
flat and to be fitted with 3 nos of hinged hold fasts to be embedded in concrete
prop. 1:2:4 of 10mm wide and 75 mm deep over brick flat soling 250mm wide
including curing etc. complete.
Rs.446.97
a) With 25mmx50mm (dia) roller
Each
Rs.251.84
b) With 12.50mmx50mm (dia) roller
Each
Rs.216.16
17.14 Providing roller to the gate including welding etc.complete
Page-105
COMPARATIVE STATEMENT
CH-18: STEEL AND IRON WORKS
Item
Description
no
18.1 REINFORCEMENT
18.1.1 Supplying, fitting and fixing in position reinforcement bars conforming to
relevant I.S. Code for R.C.C. work/ R.B. walling including straightening,
cleaning, cutting and bending to proper shapes and length as per details,
supplying and binding with 20G annealed black wire and placing in position
with proper blocks, supports, chairs, spacers etc. complete.
(No extra measurement for lap, hook, chair, anchor etc. will be
entertained in the measurement as they are included in the rate) (Upto
1st floor level)
a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam
steel/RINL
(i) TMT Corrosion resistant steel (CRS) reiforcement bar
Rate
Qtl
Rs.7,158.90
(ii)Super Ductile (SD) TMT reinforcement bars
Qtl
Rs.6,902.86
b) Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX)

(For Assam Type Bldg., drain works,,retaining wall&boundary wall etc.
Qtl
Rs.6,026.82
c) ISI approved Mild steel reinforcement bar(M.S.Bar)
Qtl
Rs.6,767.66
Qtl
Rs.37.75
a) In beams and joists fitted independently without connecting plates.
Qtl
Rs.6,946.00
b) In flat up to 25mm thickness
Qtl
Rs.6,620.00
c) In M.S. angles, channels, Tees etc.
Qtl
Rs.7,074.00
a) In beams and joists with connecting plates/ angle cleats
Qtl
Rs.6,729.00
b) In single stanchions (columns) composed of R.S.J. or channels with caps,

bases, splices, angle brackets etc.
Qtl
Rs.7,618.00
c) In trusses and trussed purlins up to 25m span and 15.0m overall height.
Qtl
Rs.7,316.00
a) In beams and joists with connecting plates/ angled cleat.
Qtl
Rs.7,079.00
b) In trusses and trussed purlins up to 25m span and 15.0m overall height.
Qtl
Rs.7,320.00
18.1.2 Extra over item 18.1.1(a,b,c) for each subsequent floor or part thereof
above first floor level.
18.2
Unit
BEAMS AND JOISTS
18.2.1 Structural steel work in sigle sections including cutting, hoisting, fixing in
position and applying a priming coat of red lead paint (up to 4.6m height)
from plinth level including drilling holes, supplying, fitting and fixing with bolts
and nuts or welding, if necessary as directed.
18.2.2 Steel work riveted and/ or bolted/ riveted in built up sections, frame work
including cutting, hoisting, fixing in position and applying a priming coat of
red- lead paint up to 4.6m height above plinth including drilling holes,
supplying, fitting and fixing with bolts and nuts or welding, if necessary as
directed.
18.2.3 Steel work welded in built up sections, framed work including cutting,
hoisting and fixing in positions and applying priming coat of red-lead paint
including drilling holes, supplying, fitting and fixing with bolts and nuts or
welding, if necessary as directed.
Ch-18 : Steel and Iron Works
Page-106
Item
Description
no
18.3
ROOF TRUSS
18.3.1 Providing fitting, hoisting and fixing of roof trusses including purlins
fabricated using MS circular hollow section conforming to relevant I.S. code,
as per approved design and drawings including providing M.S. cleats, base
plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and
two coats of approved enamel paints complete including fitting necessary
cleats etc. for fixing ceiling joists as per design and drawing as directed.
Unit
Rate
a) TATA make Circular Hollow section- CHS of Grade YST-310

conforming to I.S. Specification : 1161-1998
Qtl
Rs.8,839.00
b) Using other ISI marked approved circular hollow section
Qtl
Rs.8,410.00
a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S.

code 4923 : 1997
Qtl
Rs.9,334.00
b) Using other ISI marked approved brand tube
Qtl
Rs.9,055.00
18.4.1 Providing and fixing in position collapsible M.S. shutters with vertical
channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm
size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia
steel pulleys complete with bolts and nuts, locking arrangements, stoppers,
handles including applying a priming coat of red lead paint.
Sq.m.
Rs.4,245.50
18.4.2 Providing and fixing rolling shutters of approved make made of 80mm wide
M.S. laths interlocked together through their entire lenth and jointed together
at the ends by end-locks mounted on specially designed pipe shaft with
bracket plates, guide channels and arrangements for inside and outside
locking with push-pull operation complete including cost of wire, spring and
hood cover for the shutters.
Sq.m.
Rs.3,069.00
18.5.1 Providing, fitting and fixing steel windows/ ventilators (openable) of standard
rolled steel sections as per relevant I.S. Code-1038 joints mitred and welded
with 15mmx3mmx100mm lugs embedded in cement concrete block of M-10
grade including providing and fixing of projecting hinges (not more than
65mm and not less than 15mm wide) bolting device and steel handles, peg
stays of 300mm long etc. complete as per drawing including applying a
priming coat of red-lead paint.
Sq.m.
Rs.2,632.90
18.5.2 Providing, fitting and fixing steel windows/ ventilators (fixed) of standard
rolled steel sections as per relevant I.S. Code, joints mitred and welded with
15mmx3mmx100mm lugs embedded in cement concrete block of M-10
grade including applying a coat of red-lead primer.
Sq.m.
Rs.1,554.40
18.3.2 Providing, fitting, hoisting and fixing of roof trusses fabricated out of
combination of any two or all of the following sections (i) Square section (ii)
Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular
hlollow section of Grade 210 including purlins, bottom runners and providing
M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer
including fitting bottom runner and cleat etc. for fixing ceiling joist as per
design complete as directed as per specifications.
18.4
18.5
COLLAPSIBLE / ROLLING SHUTTERS
WINDOWS / VENTILATORS
Page-107
Item
Description
no
18.5.3 Providing, fitting and fixing steel windows of standard rolled steel sections as
per relevant I.S. Code, joints mitred and welded with 15mmx13mmx100mm
lugs embedded in cement concrete block of M-10 grade including providing
and fixing of projecting hinges (not more than 65mm and not less than
15mm wide) bolting device, steel handles, pegs, stays of 300mm long etc.
complete including providing 12mmx12mm sq. bars duly welded to steel
frame at not more than 12cm c/c applying a priming coat of red-lead paint
etc. complete as per drawing.
a) Openable
b) Fixed
Unit
Rate
Sq.m.
Sq.m.
Rs.3,087.70
Rs.2,119.60
Sq.m.
Rs.4,461.90
a) M. S. Angles.
Qtl
Rs.10,344.45
b) M. S. Flats.
Qtl
Rs.9,604.99
c) M. S. bolts & nuts.
Qtl
Rs.9,982.23
Rs.354.60
(i) Size 90mm x 60mm (Single rebate)
Rs.713.20
(ii) Size 105mm x 60mm (Single rebate)
Rs.713.20
(iii) Size 125mm x 60mm (Single rebate)
Rs.725.20
(iv) Size 125mm x 60mm (Double rebate)
Rs.853.30
(v) Size 165mm x 60mm (Double rebate)
Rs.942.70
Rs.785.60
18.5.4 Providing, fitting and fixing steel ventilators (openable) of standard rolled
steel sections as per relevant I.S. Code, joints mitred and welded with
15mmx13mmx100mm lugs embedded in cement concrete block of M-10
grade including providing and fixing of projecting hinges (not more than
65mm and not less than 15mm wide) bolting device, handles, pegs, stays of
300mm long etc. complete including providing 2nos. of 12mmx12mm sq.
bars (horizontal) duly welded to steel frame and applying a priming coat of
red oxide paint etc. complete as per drawing.
18.6
ANGLES/ FLATS/ BOLTS AND NUTS
18.6.1 Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts
including painting with red lead paint one coat complete as directed.
18.7 DOOR FRAMES

18.7.1 Supplying, fitting and fixing door frame made of M.S. equal angle of size
40mmx40mmx5mm fabricated, welded, mitred and joined as per relevant
I.S. Codes including fitting 8 nos. of M.S. hold fast, providing closing/ holding
device for 2 nos. tower bolts of door for each side and 1 no. for fitting and
fixing Aldrop (for single leaf) to the frame for fixing the door to the frame,
applying primer to all steel surfaces fixing the frame to the wall/ R.C.C.
members by embedding the hold fast securely in C.C. block of M-15 grade
complete at all levels as specified and directed. (Door hinges to be paid as
per relevant item of the schedule of rates).
18.7.2 Providing, fitting and fixing powder coated pressed steel door frame made of
1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock
jamb, head and steel base ties at the bottom of the frame. The whole frame
shall be welded or rigidly fixed together by mechanical means with base ties
of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled
up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works
etc.complete as directed by the department for all levels. (P.C.C. to be
measured and paid for seperately).
(a) 1.25mm thick sheet
(b) 1.60mm thick sheet

(i) Size 90mm x 60mm (Single rebate)
Page-108
Item
no
Description
Unit
Rate
(ii) Size 105mm x 60mm (Single rebate)
Rs.815.90
(iii) Size 125mm x 60mm (Single rebate)
Rs.849.70
(iv) Size 125mm x 60mm (Double rebate)
Rs.948.80
(v) Size 165mm x 60mm (Double rebate)
Rs.1,009.20
Sq.m.
Rs.5,381.77
18.8 CATTLE TRAP

18.8.1 Supplying fitting and fixing M.S. cattle trap fabricated, welde, mitred and
jointed as per relevant IS code with ISMB 250 joist spaced not more than
1800mm apart and ISA 65 x 65 x 6 spaced not more than 200mm apart and
fixing the same over RCC member / Brick wall complete as specified and
directed.
Page-109
CH-19: PLINTH PROTECTION WORKS

Item
Description
no
19.1 Providing plinth protection 50mm thick to cement concrete 1 : 3 : 6 with coarse
agg.of 20mm nominal size including finishing the surface with 10mm thick cement
plaster in proportion 1:3 with a floting coat of neat cement finished.
Unit
Rate
Sqm
Rs.342.80
Sqm
Rs.665.72
Sqm
Rs.710.43
i). 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth
of 100mm.
Rm
Rs.888.38
ii). 300mm wide and average 250mm deep with bed slope 1 in 150 with initial
depth of 100mm.
Rm
Rs.1,093.04
i). 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth
of 100mm.
Rm
Rs.796.21
ii). 300mm wide and average 250mm deep with bed slope 1 in 150 with initial
depth of 100mm.
Rm
Rs.975.10
19.2 Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished
with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement
finish.
19.3 Providing plinth protection with bricks laid on edge and grouted with cement
mortar 1:4 and finishing with cement pointing in prop. 1:1 complete.
19.4 Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over
brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a
floating coat of cement slurry as directed with necessary shttering for sides and
earth work in excavation of foundation trenches and refilling the sides after
completion of work etc. as specified.
19.5 Providing drain with brick work in cement mortar in proportion 1:5 with half brick
thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including
15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement
slurry as directed with necessary shttering for sides and earth work in excavation of
foundation trenches and refilling the sides after completion of work etc. as
specified.
Ch-19 : Plinth Protection
Page-110
CH-20: LANDSCAPING
Item
No.
20.1
20.2
Unit
Rate
(a) By Doob grass (Cynodon dactylon)
Sqm
Rs.332.13
(b) By Carpet grass (Axonopus affinis)
Sqm
Rs.335.04
Sqm
Sqm
Rs.434.46
Rs.496.28
(A) With Aeirides

(I) Using earthen pot of 30 cm dia.
each
Rs.426.30
(II) Using earthen pot of 60 cm dia.
each
Rs.455.56
(III) Using concrete pot of 60 cm dia.
each
Rs.536.98
each
Rs.660.02
each
Rs.686.95
each
Rs.871.46
each
Rs.950.79
each
Rs.977.73
each
Rs.1,162.23
each
Rs.2,388.12
each
Rs.2,430.36
each
Rs.2,614.86
LAWN MAKING BY DIBBLING
Supplying and dibbling of selected lawn grass [ Doob grass (Cynodon dactylon),
cushion grass (Axonopus affinis)] after preparing the land by ploughing / working to
a depth of 40 -45 cm, removing of all unwanted debris ( rubbles, pebbles, plant
roots etc.), mixing of organic manure(10kg - 15kg/sq.m), levelling the surface and
initial maintenance by proper and periodic rolling, mowing and irrigation etc.( as
specified) for a period of six months from the date of dibbling including the
application of recommended dose of fertilizers(N:P:K) mixture as specified and
directed by the department.
LAWN MAKING BY TURFING

Supplying and laying of selected grass turves [ size 60 cm x 30 cm] after preparing
the land by removing of all unwanted debrises ( rubbles, pebbles, plant roots etc.),
mixing of organic manure, levelling the surface and initial maintenance by proper
and periodic rolling, mowing and irrigation etc.( as specified) for a period of six
months from the date of laying of grass including the application of recommended
dose of fertilizers(N:P:K) mixture as specified and directed by the department.
(a) By Bahpotia grass and Doob grass (Cynodon dactylon) :
(b) BY CARPET GRASS (Axonopus affinis) :
20.3
POT PLANTING
Supplying and planting of terrestrial orchids with required size of pot including
filling the pot to the top surface with appropriate soil media made of garden soil,
river sand, cow-dung, leaf mould, fertilizer, pesticides as per specification and
necessary maintenance for a period of 4 months from the date of planting
complete as specified and directed . (Mixing of different ingredients of soil media
to be made in presence of Deptt. official / Specialist concerned)
(B) With Dendrobium (Hybrid)
(C) With Mokara
(D) With Vanda (hybrid)
Ch-20 : Landscaping
Page-111
Item
No.
20.4 Supplying and planting of house plants in required size of pot including filling the
pot to the top surface with appropriate soil media of garden soil, river sand, cowdung, leaf mould, fertilizer, pesticides as per specification and necessary
maintenance for a period of 6 months from the date of planting complete as
specified and directed . (Mixing of different ingredients of soil media to be made in
presence of Deptt. official / Specialist concerned)
Unit
Rate
(i) Using earthen pot of 30 cm dia.
each
Rs.262.98
(ii) Using earthen pot of 60 cm dia.
each
Rs.340.85
(iii) Using concrete pot of 60 cm dia.
each
Rs.423.49
each
Rs.262.98
each
Rs.340.85
each
Rs.423.49
each
Rs.262.98
each
Rs.340.85
each
Rs.423.49
each
Rs.286.24
each
Rs.364.11
each
Rs.446.75
each
Rs.297.87
each
Rs.375.74
each
Rs.458.38
each
Rs.303.69
each
Rs.381.55
each
Rs.464.19
(G) With English Ivy

each
Rs.286.24
each
Rs.364.11
each
Rs.446.75
each
Rs.558.16
each
Rs.636.02
each
Rs.718.66
(A) With Fancy leaf caladium/Coleus
(B) With Indian rubber plant / Prayer plant
(C) With Fragrant dracaena / Silver net leaf / Philodendron / Devil's back bone
/Peperomea/Croton
(D) With Peacock/spider/Umbrella
(E) With Maiden hair fern/Aloe/Boston fern/Swiss cheese plant/Forget me not
(F) With Marry Christmas begonia / Polypodium / Aluminium plant
(H) With Iron Cross Begonia
(I) With Anthurium

Ch-20 : Landscaping
Page-112
Item
No.
Unit
Rate
(A) With Bottle palm

each
Rs.244.43
each
Rs.335.03
each
Rs.417.67
each
Rs.271.00
each
Rs.348.86
each
Rs.431.50
(C) With Chinese Palm

each
Rs.294.26
each
Rs.372.13
each
Rs.454.77
(D) With Fan Palm /Finger palm

each
Rs.500.00
each
Rs.577.87
each
Rs.660.51
each
Rs.184.38
each
Rs.274.98
each
Rs.357.62
each
Rs.369.74
each
Rs.455.44
(J) With Selloum
(K) With Birdnest fern/Good luck plant
20.5
Supplying and planting of palms with required size of pot including filling the pot to
the top surface with appropriate soil media made of garden soil, river sand, cowdung, leaf mould, fertilizer, pesticides as per specification and necessary
(B) With Erica palm (Butterfly palm)/ Kentia palm
20.6
20.7
Supplying and planting of seasonal flower in required size of pot including filling the
pot to the top surface with appropriate soil media made of garden soil, river sand,
cow-dung, leaf mould, fertilizer, pesticides as per specification and necessary
Supplying and planting of cactus in required size of pot including filling the pot to
the top surface with appropriate soil media made of garden soil, sand, cow-dung,
fertilizer, pesticides as per specification and necessary maintenance for a period of
6 months from the date of planting complete as specified and directed . (Mixing of
different ingredients of soil media to be made in presence of Deptt. official /
Specialist concerned)
(A) With Peanut Cactus / Rat tail Cactus
Ch-20 : Landscaping
Page-113
Item
No.
Unit
Rate
each
Rs.538.08
(B) With Prickly pear

each
Rs.393.00
each
Rs.478.70
each
Rs.510.41
(C) With Parodia globular

each
Rs.270.88
each
Rs.513.59
each
Rs.596.23
each
Rs.136.04
Supplying and planting of selected rose plants on the ground (as specimen bush)
including the preparation of the pit ( 45 cm x 45 cm x 45 cm ), removing unwanted
debrises, filling the pit with manure and fertilizers as per specification and
necessary maintenance for a period of 1year from the date of planting complete as
specified and directed .
(A) With Pompon Rose
each
Rs.476.22
(B) With Hybrid tea rose / Miniatune rose
each
Rs.464.59
metre
Rs.352.72
(ii) With Kamini
metre
Rs.396.80
(iii) With Chinese Bamboo
metre
Rs.401.45
(iv) With Thuja / Ixora
metre
Rs.494.49
(i) With Duranta
metre
Rs.483.35
(ii) With Kamini
metre
Rs.596.97
(iii) With Chinese Bamboo
metre
Rs.606.27
(iv) With Thuja / Ixora
metre
Rs.792.37
metre
Rs.362.03
20.8
20.9
BED PLANTING
Supplying and planting of Dahlia / Chrysanthemum / Gladiolus on the ground ( bed
planting, bed size 45 cm x 45 cm x 45 cm) including the preparation of the soil,
providing organic manure and fertilizer, pesticides as per specification and
complete as specified and directed .
HEDGE PLANTING / EXTERNAL HEDGE

20.10 Supplying and planting of suitable plant materials for preparation protective /
external hedge (50 cm wide) including the preparation of the ground by mixing
organic manure and fertilizers as per specification and necessary maintenance for a
period of one year from the date of planting complete as specified and directed .
(A) ADOPTING SINGLE ROW PLANTING METHOD
(i) With Duranta
(B) ADOPTING CROSS WISE DOUBLE ROW PLANTING METHOD
EDGE PLANTING / INTERNAL HEDGE

20.11 Supplying and planting of suitable plant materials for edge making / Internal
hedge(20 cm wide) including the preparation of the ground by mixing organic
manure and fertilizers as per specification and necessary maintenance for a period
of one year from the date of planting complete as specified and directed .
(A) ADOPTING SINGLE ROW PLANTING METHOD
(i) With Duranta
Ch-20 : Landscaping
Page-114
Item
No.
Unit
Rate
(ii) With Coleus
metre
Rs.400.65
(iii) With Brindavan / Latifolius
metre
Rs.436.34
(iv) With Acalypha wilkesiana
metre
Rs.517.76
(v) With Acer palmatum
metre
Rs.558.46
(i) With Duranta
metre
Rs.501.96
(ii) With Coleus
metre
Rs.579.22
(iii) With Brindavan / Latifolius
metre
Rs.676.06
(iv) With Acalypha wilkesiana
metre
Rs.838.89
(v) With Acer palmatum
metre
Rs.920.31
SHADE TREE
(A) Neem / Mahaneem / Beef wood / Bakul / Acacia / Siris / Devils tree / Kadam /
Palash / Pink Cassia / peepal / Silver oak / Simalu / Ajar
each
Rs.299.34
(B) Kanchan / Nahar / Arjunu

(C) Sonaru
each
each
Rs.305.16
Rs.310.97
(D) Bottle Brush / Nil Gulmohar / Debadaru / Weeping Willow
each
Rs.340.05
(E) Ravenala
each
Rs.340.05
(F) Paine
each
Rs.362.21
(G) Christmas tree / Kuki
each
Rs.378.55
(A) Gulmohar / Ashok
each
Rs.305.16
(B) Kanchan
each
Rs.328.42
(A) Radhachura / Krishnachura / Rat ki rani / Ixora / Jetuka
each
Rs.368.02
(B) Allmanda / Khorika zai / May flower / Kamini / Kathanda / Tecoma / Acalypha /
Bougainvillea / Dracaena / Togor / Nilakantha / Mussaenda
each
Rs.373.84
(C) Korobi / Azalea
each
Rs.379.66
(D) Thuja
(E) Poinsettia / Forget me not
each
each
Rs.379.66
Rs.391.29
(B) ADOPTING CROSS WISE DOUBLE ROW PLANTING METHOD
12
TREE PLANTING
Supplying and planting of ornamental trees (1'-0" height sapling) including pit
making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media,
Flowering Tree
SHRUB PLANTING
20.13 Supplying and planting of ornamental shrub ( below 1'-0" height ) including pit
making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media,
AQUATIC PLANT
Ch-20 : Landscaping
Page-115
Item
No.
20.14 Supplying and planting of aquatic plants ( water Lily and Lotus )after preparation of
under water soil including organic manuring, supplying the required quantity of
water and maintenance for a period of one year from the date of completion
complete as specified and directed.
20.15 Preparation of a carpet bedding by raising the backside of the bed to a height of 45
cm (average) after mixing organic manure, fertilizer including supplying and
planting of grass and specimen plants (Brindavan) to engrave the desired letters,
complete as directed and specified by the department.
Unit
Rate
Sqm
Rs.516.78
Sqm
Rs.686.22
20.16 Construction of a pergola ( Width = 2.0 m, Height of the side posts = 1.8 m, Height
at the apex = 2.8 m) with angle iron of size 50 mm x 50 mm x 5 mm (placing at
2000 mm apart ) embedding the iron posts in P.C.C. base ( not less than 600 mm)
covering at the top and sides by chain link fencing, painting one coat of primer and
two coats of paint including supplying and planting of flowering climbers as
enclosed from both sides ( 3 nos. per metre in one side ) of the pergola to facilitate
climbing by pit making (30 cm x 30 cm x 30 cm) filling the pit with the mixture of
soil and organic manure and necessary maintenance by trimming etc complete as
specified and directed by the department. (P.C.C. and soling to be measured and
paid separately)
20.17 Supplying and placing of orchid house of size 3.00 m x 1.5 m x 2.00 m with tub
stand, make of 15 mm dia. G.I. Pipe with M.S. rod, M.S. flat etc. including roof
frame, painting two coats, covering the roof with 75 % heat absorbing black nets
and three sides with wire net complete as directed and specified.
metre
Rs.5,699.85
each
Rs.23,587.77
20.18 Edging with bricks laid dry lengthwise including excavation, refilling, consolidating
with hand packing and spreading neatly surplus earth within a lead of 50 m.
each
Rs.38.93
20.19 Half brick circular tree guard internal diametre 1.25 m and height 1.2 m above
ground and 0.02 m below ground bottom two coarses laid dry and top three
coarses in cement mortar 1:6 and the intermediate coarses being in dry honey
comb masonry as per design complete.
each
Rs.2,090.61
20.20 Making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar
drums including providing and fixing 2 nos. M.S. sheet rings (50 x 0.50) mm with
rivets complete in all respects including painting inside and outside of tree gaurd .
each
Rs.135.44
(A) F-25 (filament ht. 25mm)
Sqm
Rs.3,582.50
(B) PGF (filament ht. 32mm)
Sqm
Rs.6,678.00
(C) L-35 (filament ht. 35mm)
Sqm
Rs.4,722.90
(D) FTS (filament ht. 40mm)
Sqm
Rs.4,815.00
(E) FTT (filament ht. 60mm)
Sqm
Rs.7,649.00
(F) FTOS 1S (filament ht. 65mm)
Sqm
Rs.7,649.00
Supplying and installation of Field Turf Turket PVC sports surface (vinyl sports floor
covering) over fibreglass mat with PVC foam backing including anti bacterial
20.21 coating and protected with dirt resistant treatment for ease of maintenance
complete as specified and directed.
Ch-20 : Landscaping
Page-116
CH-21 : PILING WORKS

Item
No.
21.1
UNIT
Rate
MANUALLY DRIVEN R.C.C. PILE
21.1.1 Providing cast in-situ manually driven reinforced cement concrete piles of using required
grade of cement concrete of required bore-diameter, bulb diameter, lengths and with
reinforcement as per specifications and drawings. Reinforcement to be measured and paid
seperately as per item no. 21.4.1
(A) SINGLE UNDER - REAMED PILE
I) Concrete grade M20
a) Pile Dia 250 mm with 625 mm bulb diameter
i) Upto 5 M
Rm
Rs. 506.40
ii) Above 5M
Rm
Rs. 513.07
i) Upto 5 M
Rm
Rs. 688.34
ii) Above 5M
Rm
Rs. 717.79
i) Upto 10 M
Rm
Rs. 912.21
ii) Above 10 M
Rm
Rs. 944.68
i) Upto 10 M
Rm
Rs. 1,252.06
ii) Above 10 M
Rm
Rs. 1,299.48
i) Upto 10 M
Rm
Rs. 1,613.82
ii) Above 10 M
Rm
Rs. 1,668.05
i) Upto 10 M
Rm
Rs. 2,029.11
ii) Above 10 M
Rm
Rs. 2,087.37
i) Upto 5 M
Rm
Rs. 807.27
ii) Above 5M
Rm
Rs. 866.99
i) Upto 10 M
Rm
Rs. 1,097.95
ii) Above 10 M
Rm
Rs. 1,121.74
i) Upto 10 M
Rm
Rs. 1,483.69
ii) Above 10 M
Rm
Rs. 1,504.10
i) Upto 10 M
Rm
Rs. 1,940.76
ii) Above 10 M
Rm
Rs. 1,953.80
b) Pile dia 300 mm with 750 mm bulb diameter
c) Pile dia 350 mm with 875 mm bulb diameter
d) Pile dia 400 mm with 1000 mm bulb diameter
e) Pile dia 450 mm with 1125 mm bulb diameter
f) Pile Dia 500 mm with 1125 mm bulb diameter
(B) DOUBLE UNDER - REAMED PILE

a) Pile dia 300 mm with 750 mm bulb diameter
(b) Pile dia 350 mm with 875 mm bulb diameter
c) Pile dia 400 mm with 1000 mm bulb diameter
d) Pile dia 450 mm with 1125 mm bulb diameter
e) Pile Dia 500 mm with 1125 mm bulb diameter
Ch-21 : Piling Works
Page-117
Item
No.
UNIT
Rate
i) Upto 10 M
Rm
Rs. 2,474.23
ii) Above 10 M
Rm
Rs. 2,473.55
i) Upto 10 M
Rm
ii) Above 10 M
Rm
C) UNIFORM PILE
a) Pile Dia 250 mm
i) Upto 5 M
Rm
Rs. 413.24
ii) Above 5M
Rm
Rs. 442.28
i) Upto 5 M
Rm
Rs. 613.70
ii) Above 5M
Rm
Rs. 636.86
i) Upto 10 M
Rm
Rs. 866.52
ii) Above 10 M
Rm
Rs. 947.35
i) Upto 10 M
Rm
Rs. 1,131.90
ii) Above 10 M
Rm
Rs. 1,237.30
i) Upto 10 M
Rm
Rs. 1,431.94
ii) Above 10 M
Rm
Rs. 1,566.24
i) Upto 10 M
Rm
Rs. 1,689.59
Above 10 M
Rm
Rs. 1,875.03
i) Pile dia 300 mm with 750 mm bulb diameter
Rm
Rs. 787.92
ii) Pile dia 350 mm with 875 mm bulb diameter
Rm
Rs. 1,038.92
iii) Pile dia 400 mm with 1000 mm bulb diameter
Rm
Rs. 1,362.82
iv) Pile dia 450 mm with 1125 mm bulb diameter
Rm
Rs. 1,728.86
v) Pile dia 500 mm with 1250 mm bulb diameter
Rm
Rs. 2,132.62
vi) Pile dia 550 mm with 1375 mm bulb diameter
Rm
Rs. 2,564.82
vii) Pile dia 600 mm with 1500 mm bulb diameter
Rm
Rs. 2,944.57
Rm
Rs. 813.25
Rm
Rs. 1,112.88
b) Pile Dia 300 mm
c) Pile Dia 350 mm
d) Pile Dia 400 mm
e) Pile Dia 450 mm
f) Pile Dia 500 mm
21.2
MACHINE DRIVEN PILES
21.2.1 Providing cast in-situ machine driven reinforced cement concrete piles of required borediameter, bulb diameter, lengths and with reinforcement as per specifications and drawings
including using of Bentonite solution. (Reinforcement to be measured and paid seperately as
per item no. 21.4.1)
(A) SINGLE UNDER - REAMED PILE
(I) Concret garade M20
(II) Concrete Grade M25
Page-118
Item
No.
UNIT
Rate
Rm
Rs. 1,460.60
Rm
Rs. 1,854.07
Rm
Rs. 2,288.96
Rm
Rs. 2,756.15
Rm
Rs. 3,174.85
Rm
Rs. 813.44
Rm
Rs. 1,124.45
Rm
Rs. 1,489.20
Rm
Rs. 1,907.57
Rm
Rs. 2,375.56
Rm
Rs. 2,881.45
Rm
Rs. 3,336.48
Rm
Rs. 1,204.53
Rm
Rs. 1,596.08
Rm
Rs. 2,045.73
Rm
Rs. 2,549.68
Rm
Rs. 3,096.48
Rm
Rs. 3,783.89
i) Pile dia 300 mm
Rm
Rs. 704.28
ii) Pile dia 350 mm
Rm
Rs. 953.04
iii) Pile dia 400 mm
Rm
Rs. 1,236.74
iv) Pile dia 450 mm
Rm
Rs. 1,549.85
v) Pile dia 500 mm
Rm
Rs. 1,890.35
vi) Pile dia 550 mm
Rm
Rs. 2,247.36
vii) Pile dia 600 mm
Rm
Rs. 2,552.83
i) Pile dia 300 mm
Rm
Rs. 754.18
ii) Pile dia 350 mm
Rm
Rs. 1,020.97
Rm
Rs. 1,325.44
iv) Pile dia 450 mm
Rm
Rs. 1,662.13
v) Pile dia 500 mm
Rm
Rs. 2,029.00
vi) Pile dia 550 mm
Rm
Rs. 2,415.09
vii) Pile dia 600 mm
Rm
Rs. 2,752.41
(B) DOUBLE UNDER - REAMED PILE

C) UNIFORM PILE
(III) Concrete Grade M30
Page-119
Item
No.
21.3
UNIT
Rate
i) Pile dia 500 mm
Rm
Rs. 2,046.74
ii) Pile dia 550 mm
Rm
Rs. 2,436.63
Rm
Rs. 2,777.99
i) Pile Dia 250 mm
Rm
Rs. 294.45
ii) Pile Dia 300 mm
Rm
Rs. 378.73
iii) Pile Dia 350 mm
Rm
Rs. 439.23
iv) Pile Dia 400 mm
Rm
Rs. 556.28
v) Pile Dia 450 mm
Rm
Rs. 686.52
vi) Pile Dia 500 mm
Rm
Rs. 988.38
i) Pile Dia 250 mm
Rm
Rs. 39.75
ii) Pile Dia 300 mm
Rm
Rs. 58.45
Rm
Rs. 81.22
iv) Pile Dia 400 mm
Rm
Rs. 108.23
v) Pile Dia 450 mm
Rm
Rs. 139.76
vi) Pile Dia 500 mm
Rm
Rs. 175.98
vii) Pile Dia 600 mm
Rm
Rs. 263.25
i) Pile Dia 250 mm
Rm
Rs. 46.19
ii) Pile Dia 300 mm
Rm
Rs. 67.92
Rm
Rs. 94.38
iv) Pile Dia 400 mm
Rm
Rs. 125.77
v) Pile Dia 450 mm
Rm
Rs. 162.41
vi) Pile Dia 500 mm
Rm
Rs. 204.50
vii) Pile Dia 600 mm
Rm
Rs. 305.91
i) Pile Dia 500 mm
Rm
Rs. 208.16
ii) Pile Dia 550 mm
Rm
Rs. 120.08
Pile Dia 600 mm
Rm
Rs. 311.38
(i) 250 mm dia
Rm
Rs. 96.78
(ii) 300 mm dia
Rm
Rs. 124.10
Stone Pile
21.3.1 Stone Pile

Providing stone piles of required diameter and length in ordinary / dense soil etc. using 25
mm dowm graded stone aggregate or river gravel including cost of boring including watering,
ramming etc. as required, Cost of T&P complete as directed and specified by the department.
21.4
MISCELLANEOUS
21.4.1 Extra for using admixture & plasticiser

(a) RCC grade M20
(b) RCC grade M25
(c ) RCC grade M30
21.4.2 Extra for boring specified diameter pile in high sub-soil water level requiring use of drilling
mud and extra cement
Page-120
Item
No.
UNIT
Rate
(ii) 350 mm dia
Rm
Rs. 156.90
(iii) 400 mm dia
Rm
Rs. 184.23
(iv) 450 mm dia
Rm
Rs. 227.95
(v) 500 mm dia
Rm
Rs. 282.61
(vi) 600 mm dia
Rm
Rs. 337.27
a) Pile Dia 250 mm
Rm
Rs. 120.84
b) Pile Dia 300 mm
Rm
Rs. 171.72
c) Pile Dia 350 mm
Rm
Rs. 209.35
d) Pile Dia 400 mm
Rm
Rs. 236.38
e) Pile Dia 450 mm
Rm
Rs. 302.10
f) Pile Dia 500 mm
Rm
Rs. 346.62
g) Pile Dia 550 mm
Rm
Rs. 385.31
h) Pile Dia 600 mm
Rm
Rs. 421.35
21.4.3 Empty boring for specified diameter piles from ground level to cut-off level.
21.5
REINFORCEMENT
21.5.1 Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for
reinforced cement concrete works in piles including straightening, cleaning, cutting and
bending to proper shapes and length as per specifications and drawings. The rings should be
welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap
length, hook, chair, bend, anchor...etc)
21.6
(A) TMT bar made of Primary producer (From Primary producer)
Qtl
(B) TMT bar of other ISI marked (From Secondary producer)
Qtl
(C) ISI approved M.S. Rod
Qtl
Rs. 7,074.82
Ton
Rs. 947.87
Ton
Rs. 1,143.05
Rs. 7,210.68
Rs. 6,395.53
LOAD TEST ON PILES

ROUTINE TESTS
21.6.1 Routine test for test loading to 1.5 times the specified safe working load including
construction of any test pile cap and dismantling the same after completion of test. (Rate
for Safe working Load)
21.6.2 Initial test for test loading to 2 times the specified safe working load including construction
of any test pile cap and dismantling the same after completion of test. (Rate for Safe working
Load)
Page-121
CHAPTER 22 : WATERPROOFING, CONCRETE ADMIXTURES & CHEMICAL

TREATMENT,REPAIR,REHABILITATION & RE-STRENGTHENING OF STRUCTURES
Item
No.
22
Unit
Rate
WATERPROOFING, REPAIR & RESTRENGTHENING OF STRUCTURES
22.1 SURFACE PREPARATION

22.1.1 Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank,
OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed
by power washing for making the surface absolutely free from any foreign particles
like dust, oil, grease etc. and allowing surface to dry complete as directed at all
levels.
22.1.1.1 Extra over Item No. 22.1.1, for removing and chipping of brick bat corba, tar felt or
any other existing protective layer over roof slab etc.
Sqm
Rs.26.78
Sqm
Rs.24.74
22.1.2 Doing patch work in roof slab/ Raft slab wherever necessary by laying small
portions of Polymer modified mortar - Cement sand mortar (in prop 1:4) mixed
with 100% acrylic Polymer Master Crete M-81 of Choksey Chemicals/Dr. Sealkit
Sealcrete (Asian Chemicals) / Rheomix 115 of BASF@ 4% by weight of cement as
specified & directed by the Department complete after proper surface preparation
(surface preparation including thorough cleaning of surface to be measured and
paid separately).
Sqm
Rs.130.27
22.1.3 Doing patch work in roof slab/ Raft slab wherever necessary by laying small
portions of two component Polymer Modified Mortar Sika Top 122 as specified &
directed by the Department complete after proper surface preparation (surface
preparation including thorough cleaning of surface to be measured and paid
separately).
Sqm
Rs.268.51
22.1.4 Doing patch work in existing roof slab wherever necessary by laying small portions
of Prepacked Polymer modified cementitious mortar - Renderoc S2 of Fosroc
Chemicals/Emaco S88CT of BASF as specified & directed by the Department
complete after proper surface preparation (surface preparation including thorough
cleaning of surface to be measured and paid separately).
Sqm
Rs.1,343.19
22.1.5 Doing patch work in existing roof slab wherever necessary by laying cement sand
mortar (prop.1:4) admixed with mortar modifier cum bonding agent Nitobond SBR
of Fosroc Chemicals/Rheomix 141 of BASF/Dr. Sealkit Master Bond Latex (Asian
Chemicals) @ 3Ltrs per bag of cement after applying with brush a priming coat of
Nitobond SBR/Rheomix 141 of BASF/Dr. Sealkit Master Bond Latex (Asian
Chemicals) @ 3.5sq.m. per litre as specified & directed by the Department
complete after proper surface preparation (surface preparation including thorough
cleaning of surface to be measured and paid separately).
Sqm
Rs.692.72
22.1.6 Preparing RCC surfaces in expansion joints by thoroughly cleaning with wire brush
etc. followed by power washing to make the surface absolutely free from any
foreign particles like dust, oil, grease etc. and allowing surface to dry complete as
directed at all levels.
Rm
Rs.8.40
(i) In 1 : 2 : 4 (1cement : 2coarse sand : 4aggregate) or M-15 grade.
Cum
Rs.116.34
(ii) In 1 : 1.5 : 3 (1cement : 1.5coarse sand : 3aggregate) or M-20 grade.
Cum
Rs.145.41
(iii) In 1 : 1 : 2 (1cement : 1coarse sand : 2aggregate) or M-25 grade.
Cum
Rs.221.82
22.2 CONCRETE & MORTAR ADMIXTURES

22.2.1 Extra for providing and mixing normal Plastisizer Master Plast PL-1 of Choksey
Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/ RHEOMAC 707 of BASF @
0.3% by weight of cement in concreting RCC structures as specified and directed by
the Department complete at all levels.
Ch-22 : Waterproofing
Page-122
Item
No.
22.2.2 Extra for providing and mixing Integral waterproofing compounds like Master Proof
IWP-1 of Choksey Chemicals /Dr. Sealkit No.1 (Asian Chemicals)/ RHEOMAC 707 of
BASF @ 0.2% by weight of cement for waterproofing structures like roof slabs,
basement, sunken slabs, chajjas, tunnels, water tank etc. as specified and directed
by the Department complete at all levels.
Unit
Rate
A. In concrete of proportion:
(i) 1 : 2 : 4 (1cement : 2coarse sand : 4aggregate) or M-15 grade.
Cum
Rs.91.01
(ii) 1 : 1.5 : 3 (1cement : 1.5coarse sand : 3aggregate) or M-20 grade.
Cum
Rs.113.77
(iii) 1 : 1 : 2 (1cement : 1coarse sand : 2aggregate) or M-25 grade.
Cum
Rs.173.49
(i) 1 : 3 (1cement : 3coarse sand)
Cum
Rs.95.88
(ii) 1 : 4 (1cement : 4coarse sand)
Cum
Rs.71.38
(iii) 1 : 5 (1cement : 5coarse sand)
Cum
Rs.61.09
A. In concrete of proportion:
Cum
Rs.86.56
Cum
Rs.108.11
Cum
Rs.165.70
Cum
Rs.138.67
Cum
Rs.102.63
Cum
Rs.88.33
A In concrete of proportion:
Cum
Rs.75.75
Cum
Rs.94.98
Cum
Rs.145.41
Cum
Rs.121.68
Cum
Rs.90.59
Cum
Rs.77.17
B In Plasters/ mortars of proportion:
22.2.3 Extra for providing and mixing normal Plastisizer Conplast P211/Dr. Sealkit LW
Super (Asian Chemicals) @ 80ml per bag of cement in concrete/ mortars as
specified and directed by the Department complete at all levels.
22.2.4 Extra for providing and mixing Integral waterproofing liquid admixture & plasticiser
Conplast X421 IC of Fosroc Chemicals /Rheomac 707 of BASF/Dr. Sealkit Normal
Plast (Asian Chemicals) @ 100ml per bag of cement in concrete for waterproofing
structures like roof slabs, basement, sunken slabs, chajjas, tunnels, water tank etc.
as specified and directed by the Department complete at all levels.
22.2.5 Extra for providing and mixing normal Plastisizer Plastiment BV 40 of Sika India Ltd.
/Dr. Sealkit Superplast WR 40 (Asian Chemicals)/Rheobuild 1100i of BASF@ 0.5%0.8% by weight of cement in concrete for waterproofing structures like roof slabs,
basement, sunken slabs, chajjas, tunnels, water tank etc. as specified and directed
Page-123
Item
No.
Unit
Rate
Cum
Rs.282.64
Cum
Rs.353.30
Cum
Rs.538.79
Cum
Rs.569.80
Cum
Rs.712.26
Cum
Rs.1,086.17
Cum
Rs.358.77
Cum
Rs.448.45
Cum
Rs.683.89
Cum
Rs.571.79
Cum
Rs.426.04
Cum
Rs.364.36
Cum
Rs.204.52
Cum
Rs.249.82
Cum
Rs.368.72
Cum
Rs.312.11
Cum
Rs.238.49
Cum
Rs.207.35
Sqm
Rs.1,208.50
22.2.6 Extra for providing and mixing Plastisizer Sikament 170 of Sika India Ltd. /Rheobuild
620 of BASF@ 1.0%-1.5% by weight of cement in concrete for waterproofing
structures like roof slabs, basement, sunken slabs, chajjas, tunnels, water tank etc.
22.2.7 Extra for providing and mixing waterproofing Plastisizer Plastocrete Plus of Sika
India Ltd /Dr. Sealkit LW Super (Asian Chemicals)/ RHEOMAC 730 of BASF @
200gms per bag of cement in concrete for waterproofing as specified and directed
22.2.8 Extra for fibre reinforcing concrete/ mortars by providing and mixing Recron3S of
Reliance Industries Ltd. @ 125gms per bag of cement as specified and directed by
the Department complete at all levels.
22.3 WATER PROOFING OF CHAJJAS, ROOF SLABS, TERRACES, SUNKEN SLABS, SEPTIC
TANK,OH TANK, RAFT SLAB IN BASEMENT, WALLS ETC.
22.3.1 (A) Supplying, mixing, laying and applying the following waterproofing systems over
Raft slabs, Roof slabs, Terraces etc. including curing complete as specified and
directed by the Department at all levels.:
(i) 1mm thick single coat of Master Crete M-81 of Choksey Chemicals /Dr.
Sealkit Sealcrete (Asian Chemicals)/ mixed with cement in the ratio 1:2 as a prime
coat.
Page-124
Item
No.
Unit
Rate
Sqm
Rs.1,291.75
22.3.2 Supplying, providing, mixing and laying over waterproofing layers/ coatings with
concrete screed of average 30mm thick or as per drawings/ requirements in
proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with
10mm and down well graded aggregates and admixed with a normal plasticizer like
Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian
Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter
scoring the top surface of the concrete screed @ 200mm c/c as specified and
directed by the Department.
22.3.3 Providing, supplying, mixing, laying 8mm thick cement Plastering in prop.1:6 over
R.C.C. surfaces mixed with integral waterproofing compounds like Master Proof
IWP-1 of Choksey Chemicals /Dr. Sealkit No.1 (Asian Chemicals) /Rheomac 707 of
BASF@ 0.2% by weight of cement conforming to IS:2465 as specified and directed
by the Department complete.
Sqm
Rs.161.98
Sqm
Rs.51.32
22.3.4 Providing, supplying, mixing and champhering the edges along joint of wall/
parapet wall and raft/ roof slab having champhered dimension of 150mm x 150mm
with cement sand mortar (prop.1:4) mixed with Master Proof IWP-1 of Choksey
Chemicals /Dr. Sealkit No. 1 of (Asian Chemicals)/ RHEOMAC 707 of BASF@ 0.2% by
weight of cement over a primer coat on the area to be champhered with a
combination of 100% acrylic Polymer Master Crete M-81/Dr. Sealkit Sealcrete
(Asian Chemicals)/ RHEOMAC 115 of BASF of Choksey Chemicals and cement in the
ratio 1:2 to be applied by brush as specified & directed by the Department
complete.
22.3.5 Providing and laying modified bituminous water proofing membrane system in
roof, Polymod-AP of choksey Chemicals, 3mm thick APP modified waterproofing
membrane by torch on method using LPG torch flame after applying a coat of
Bituminous primer "Primer Polymod-SB" @ 0.2kg/sq.m. complete as specified and
directed by the Department followed by :
Supplying, providing, mixing and laying of concrete screed of average 75mm thick
in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume)
with 12mm and down well graded aggregates and admixed with a normal
plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast
(Asian Chemicals) @ 0.3% by weight of cement after making the concrete fibre
reinforced for reducing the effect of thermal expansion by mixing concrete with
Recron 3S @ 1.25kg per bag of cement and/ as specified and directed by the
Department.
22.3.6 (A) Providing and applying over roof slab/ raft slab, polymer modified bituminous
waterproofing membrane Proofex SM of Fosroc chemicals on an unprimed
substrate using specially designed spray application equipment to be applied in a
single coat, using wet on wet passes to give a nominal dry film thickness of 2mm
followed by applying ProofexGeo Textile having weight of 200gm per sq.m
immediately after the application of Proofex SM membrane when the surface is
still wet but not tacky and as specified and directed by the Department.
Rm
Rs.272.64
Sqm
Rs.882.68
Sqm
Rs.594.54
Sqm
Rs.1,222.24
(B) Using RHEOMIX 131 OF BASF
(B) Providing and application of Sonosheild HLM 5000 of BASF India Ltd, the Liquid,
cold-applied elastomeric Asphalt modified Polyurethane waterproofing membrane
system of 1.2mm thick having average elongation of 600% and average tensile
strength of 1 MPA. The product shall conform ASTM C 836 & National standard of
Canada 37.58 - M86 developed by CGSB.
Page-125
Item
No.
22.3.7 Supplying, providing, mixing and laying over waterproofing layers/ coatings with
cement mortar screed of average 25mm thick or as per drawings/ requirements in
proportion 1:4 (1cement : 4sand) admixed with integral waterproofing admixture
Conplast X421IC of Fosroc Chemicals /Rheomac 707 of BASF/Dr. Sealkit Normal
Plast of (Asian Chemicals)@ 125ml per bag of cement complete as specified and
Unit
Sqm
22.3.8 Providing, supplying, mixing and coving the edges along joint of parapet wall & roof
slab/ chajja & exterior wall/ walls & raft slabs etc. with cement sand mortar
(prop.1:4) mixed with mortar modifier cum bonding agent Nitobond SBR of Fosroc
Chemicals/Rheomix 141 of BASF/Dr. Sealkit Masterbond Latex (Asian Chemicals) @
2-3Ltrs per bag of cement as specified & directed by the Department complete.
Rate
Rs.219.00
Rs.292.45
22.3.9 Providing and applying over roof/ raft slab, two coats of waterproofing slurry
prepared with cement, fine sand in prop 1:1 admixed with modified acrylic polymer
like Cemflex of Sika India Ltd./Dr. Sealkit Sealcrete (Asian Chemicals),/ RHEOMIX
131 OF BASF by brush @ 0.25% of cement-sand mixture (by weight) after proper
surface preparation (surface preparation including thorough cleaning of surface to
be measured and paid separately) as specified & directed by the Department
complete.
22.3.10 Providing and applying over sunken slab etc., two coats of waterproofing slurry
prepared with neat cement, water and modified Styrene Butadiene Rubber based
polymer like Sika Latex of Sika India Ltd./Dr. Sealkit Masterbond Latex (Asian
Chemicals)/ RHEOMIX 141 by brush after proper surface preparation (surface
preparation including thorough cleaning of surface to be measured and paid
separately) as specified & directed by the Department complete.
Sqm
Rs.218.45
Sqm
Rs.69.51
22.3.11 Supplying, providing, mixing and laying of concrete screed of average 20mm thick
or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate :
4coarse aggregate) (by volume) with 10mm and down well graded aggregates and
admixed with a waterproofing plasticizer like Plastocrete Plus of Sika India Ltd./Dr.
Sealkit LW Super (Asian Chemicals) /Rheomac 730 of BASF@ 0.2% by weight of
cement and thereafter scoring the top surface of the concrete screed @ 200mm
c/c as specified and directed by the Department.
22.3.12 15mm thick plastering of the interior surface of concrete water tanks with cement
mortar in prop 1:4 admixed with modified Styrene Butadiene Rubber based
polymer like Sika Latex of Sika India Ltd./Dr. Sealkit Masterbond Latex (Asian
Chemicals)/Rheomix 141 of BASF @ 200gms per bag of cement as specified and
directed by the department complete.
Sqm
Rs.106.23
Sqm
Rs.103.35
22.3.13 Providing, supplying, mixing and champhering the edges along joint of parapet wall
& roof slab/ chajja & exterior wall/ walls & raft slabs etc. having champhered
dimension of 150mm x 150mm with cement sand mortar (prop.1:4) mixed with
Plastocrete Plus of Sika India Ltd./Dr. Sealkit LW Super (Asian Chemicals) /Rheomac
707 of BASF@ 0.2% by weight of cement over a primer coat on the area to be
champhered with a combination of modified Styrene Butadiene Rubber based
polymer like Sika Latex of Sika India Ltd./Rheomix 141 of BASF and cement in the
ratio 1:8 to be applied by brush as specified & directed by the Department
complete.
Sqm
Rs.158.18
Page-126
Item
No.
22.3.14 Providing and laying Polymeric waterproofing membrane sheets Hyperplas
Standard of IWL India Ltd. @3kg/sq.m. having 90micron HMHDPE film as centre
core with polymeric mix of softening point 118oC and penetration of 25-40 covered
on both side and laminated with 20micron HMHDPE, layed over first coat of water
based emulsion primer @ 100gms/sq.m. and using hot blown bitumen 90/15 or
85/25 @ 1.2kg/sq.m. followed by repeatation of the bitumen coat and then final
coat of bituminous aluminium @ 100gms/sq.m. complete as specified and directed
by the Department followed by :
Unit
Rate
Sqm
Rs.510.98
22.3.15 Providing and applying of one coat of Techoxy of Choksey Chemicals as Primer coat
on RCC roof surface followed by 2 (two) coats of Tar-O-Thane with necessary tools
inclusive of labour charges in RCC buildings at all levels.
Sqm
Rs.437.38
22.3.16 Providing and applying two coats of coal tar epoxy at an interval of 12 - hours each
including all necessary tools and application in R.C.C. buildings at all levels.
Sqm
Rs.148.24
Sqm
Rs.306.50
22.4.2 Applying one coat of epoxy coating Techoxy of Choksey Chemicals followed by two
coats of Polyurethane waterproof coating Techcoat 61P at an interval of 12hours
each for waterproofing of external walls, roofs, terraces, chajjas, etc. as specified &
directed by the Department complete.
Sqm
Rs.476.72
22.4.3 Applying 2 coats of 1mm thick acrylic polymer modified cementitious

waterproofing coating Brushbond of Fosroc Chemicals/Dr. Sealkit Flexbond AP 121
C (Asian Chemicals)/ MASTERSEAL 550 of BASF for waterproofing structures like
roof slabs, basement, sunken slabs, chajjas, tunnels, water tank etc. after proper
surface preparation and soaking the surface with water prior to application
complete as specified and directed by the Department at all levels.
Sqm
Rs.326.41
22.4.4 Applying 2 coats of 1mm thick elastomeric cementitious waterproofing coating

Brushbond RFX of Fosroc Chemicals /Dr. Sealkit Flexbond AP 122 C (Asian
Chemicals) / MASTERSEAL 550EL of BASF for waterproofing structures like roof
slabs, basement, sunken slabs, chajjas, tunnels, water tank etc. after proper surface
preparation and soaking the surface with water prior to application complete as
specified and directed by the Department at all levels.
Sqm
Rs.375.97
22.4.5 Applying two coats of aliphatic acrylate based exterior coating Dekguard Std of
Fosroc Chemicals/Masterseal 300H of BASF over one coat of Silane siloxine based
Dekguard Std Primer/Masterseal 380 of BASF Primer after proper surface
preparation (surface preparation including thorough cleaning of surface to be
measured and paid separately) as specified & directed by the Department
complete.
22.4.6 Providing and applying over roof slab/ raft slab, two coats of waterproofing slurry
like SikaTop Seal 107 of Sika India Ltd./Dr. Sealkit Flexbond AP 121 C (Asian
Chemicals) ./ MASTERSEAL 550 @ 1.5kg per sq.m. per coat, by brush after proper
surface preparation (surface preparation including thorough cleaning of surface to
be measured and paid separately) as specified & directed by the Department
complete.
Sqm
Rs.245.85
Sqm
Rs.390.64
22.4 WATER PROOF COATINGS:

22.4.1 Applying a two coats of Futura Sealer Coat of Choksey Chemicals over concrete
surface/ external walls after proper surface preparation (surface preparation
including thorough cleaning of surface to be measured and paid separately)
followed by applying over sealer coat two coats of Futura-5 at a spread rate of
45sq.ft/litre after proper thinning with 10-20% of water complete as specified &
Page-127
Item
No.
22.4.7 Providing and applying of waterproofing coating like Inertol Proxitar of Sika India
Ltd. by brush for waterproofing of septic tanks, sewage treatment plants etc. after
proper surface preparation (surface preparation including thorough cleaning of
surface to be measured and paid separately) as specified & directed by the
Department complete.
22.4.8 Applying over exterior walls/ masonry walls etc. two coats of Silaoxane silane based
water repellant like Sikagard 703W/Masterseal 380 of BASF @ 250ml per sq.m. wet
on wet after properly diluting with water as specified & directed by the Department
complete.
Unit
Rate
Sqm
Rs.197.66
Sqm
Rs.153.92
Sqm
Rs.327.35
22.5.2.1 Grout slurry of cement, water and grout admixture Cebex 100 of Fosroc Chemicals
/Flowcable 50 of BASF/Dr. Sealkit NSPG (Asian Chemicals) @ 225gms per bag of
cement
Sqm
Rs.361.54
22.5.2.2 Grout of two part low viscous epoxy grout Conbextra EP10 of Fosroc
Chemicals/Concresive 1315 of BASF
Sqm
Rs.351.94
22.5.3 Providing Grouting by drilling holes @ 1M c/c upto half of the slab/ wall depth in
zigzag manner or as per drawings using a drill machine and fixing a nozzle of 18 to
20mm dia. for injecting a grout slurry of cement admixed with expanding grout
admixture Intraplast EP of Sika India Ltd./Dr. Sealkit NSPG (Asian Chemicals) /
FLOWCABLE 50 OF BASF@ 1.0% by weight of cement and water resistant bonding
agent Sika Latex, till the refusal of injected grout material from adjacent nozzle
(grouting operation pressure shall be in between 3 to 4kg per sq.cm.). Followed by
cutting the exposed nozzle so as to make the wall free from the grouting pipes and
to seal the gap with polymer modified mortar as specified and directed by the
Department complete at all levels.
Sqm
Rs.345.05
Rm
Rs.218.03
22.5 GROUTING IN R.C.C. WALLS, SLABS & RAFT SLABS:

22.5.1 Providing Grouting in R.C.C. walls by drilling holes @ 1M c/c upto half of the wall
depth in zigzag manner or as per drawings using a drill machine and fixing a nozzle
of 18 to 20mm dia. for injecting a grout slurry of cement, water and expanding
grout admixture Master grout CPG1 of Choksey Chemicals /Dr. Sealkit NSPG (Asian
Chemicals)/ FLOWCABLE 50 OF BASF @ 0.5% by weight of cement till the refusal of
injected grout material from adjacent nozzle (grouting operation pressure shall be
in between 2 to 4kg per sq.cm.). Followed by cutting the exposed nozzle so as to
make the wall free from the grouting pipes and to seal the gap with polymer
modified mortar as specified and directed by the Department complete at all levels.
22.5.2 Providing Grouting in R.C.C. walls & slabs by drilling holes @ 300mm c/c upto half
of the wall depth in zigzag manner or as per drawings using a drill machine and
fixing a nozzle of 20mm dia. for injecting a grout/ grout slurry till the refusal of
injected grout material from adjacent nozzle (grouting operation pressure shall be
in between 2 to 4kg per sq.cm.). Followed by cutting the exposed nozzle so as to
make the wall free from the grouting pipes and to seal the gap with polymer
modified mortar as specified and directed by the Department complete at all levels.
22.6 TREATMENT OF CONSTRUCTION JOINTS

22.6.1 Providing treatment of constructional joints in R.C.C. walls and slabs by supplying,
mixing and applying a 2-component epoxy resin based bonding agent for old to
new concrete like Master Bond - EP/ Concresive 1414 of BASF/Dr. Sealkit Bond OTN
(Asian Chemicals) (with an open time of 6 hours at 30 deg Celsius) as per detailed
drawings or as specified and directed by the Department complete at all levels.
(i) Slab/ Wall thickness upto 200mm
Page-128
Item
No.
Unit
Rate
(ii) Slab/ Wall thickness greater than 200mm

mixing and applying a epoxy resin based bonding agent for old to new concrete like
Nitobond - EP /Dr. Sealkit Bond OTN (Asian Chemicals)/ CONCRESIVE 1414 as per
detailed drawings or as specified and directed by the Department complete at all
levels.
Sqm
Rs.1,501.63

mixing and applying a single component modified styrene butadiene emulsion
bonding agent for old to new concrete like Nitobond - SBR /Rheomix 141 of
BASF/Dr. Sealkit MasterBond Latex (Asian Chemicals) as per detailed drawings or
Rm
Sqm
Rs.86.06
Rs.833.30
Rm
Rs.25.10
Sqm
Rs.250.82
22.6.4 Providing treatment of constructional joints in R.C.C. walls and slabs by spraying
surface retarder like Rugasol 2 liquid on old concrete surface followed by cleaning
with water jets to obtain exposed aggregates prior to laying of new concrete and
applying a 2-component epoxy resin based bonding agent for old to new concrete
like Sikadur 32LP /Dr. Sealkit Bond OTN (Asian Chemicals) (with an open time of 6
hours at 30 deg Celsius) as specified and directed by the Department complete at
all levels.
Rm
Rs.59.59
Sqm
Rs.589.16
22.7.1 Providing treatment of expansion joints by the following process as specified and
(a) Preparation of groove by nosing the groove in required sizes with Polymer
modified mortar - Cement sand mortar (in prop 1:3) mixed with Master Crete M-81
of Choksey Chemicals /Dr. Sealkit Sealcrete (Asian Chemicals) /Rheomix 115 of
BASF@ 15% by weight of cement over a bonding coat of Master Crete M81/Rheomix 131 of BASF mixed with cement in the ratio 1:2 as specified & directed
by the Department complete after proper surface preparation including cleaning/
chipping removing all sorts of loose particles and foreign materials and cleaning
surface thoroughly (surface preparation including thorough cleaning of surface to
(b) Providing and applying two coat of Techseal RDL 942 Primer in both surface of
the expansion joint followed by applying Tech seal 940 Polysulphide sealant on
vertical joint surface after proper fixing of the necessary backup materials as
specified and directed by the Department complete.
Rm
Rs.194.81
Rm
Rs.1,047.52
(C) Providing and applying MASTERFLEX 700i of BASF India Ltd, two-component,
high performance polysulfide formulation having weathering resistance to
ultraviolet rays. The product shall exhibit shore A hardness of 25 and have
movement accommodation factor of 25%. The sealant must comply with the
performance specifications as laid in BS:4254 and ASTM C 920. All the joints must
be primed using compatible primer for the substrate from the MASTERFLEX
PRIMER range. Sealant application shall be carried out, strictly in accordance with
Manufacturers recommendations.
Rm
Rs.1,172.62
22.7 TREATMENT OF EXPANSION JOINTS
Page-129
Item
No.
Unit
Rate
(d) (Upto 40 mm: )

Providing and applying two coat of Masterflex Primer in both surface of the
expansion joint followed by applying of one component Polyurathene based joint
sealant MASTERFLEX 472/474 of BASF India Ltd, which is having specific gravity of
1.30gm/cm, elongation at break will be > 600% and recoverability will be > 80%
joint surface after proper fixing of the necessary backup materials as specified and
(a) Preparation of groove of required sizes by nosing the groove with cement sand
mortar (prop.1:4) mixed with mortar modifier cum bonding agent Nitobond SBR of
Fosroc Chemicals /Rheomix 141 of BASF/Dr. Sealkit Master Bond Latex (Asian
Chemicals) @ 2-3Ltrs per bag of cement as specified & directed by the Department
complete after proper surface preparation including cleaning/ chipping removing
all sorts of loose particles and foreign materials and cleaning surface thoroughly
(surface preparation including thorough cleaning of surface to be measured and
paid separately).
(b) Providing and applying two coat of Primer 4 in both surface of the expansion
joint followed by applying polysulphide sealant Thioflex 600 on vertical joint
surface after proper fixing of the necessary backup materials as specified and
Rm
Rs.1,126.16
Rm
Rs.204.99
Rm
Rs.1,119.56
(a) Preparation of groove by nosing the groove in required sizes with Cement sand
mortar (in prop 1:4) mixed with Sika Latex of Sika India Ltd. /Dr. Sealkit Master
Bond Latex (Asian Chemicals)@ 4% by weight of cement as specified & directed by
the Department complete after proper surface preparation including cleaning/
chipping removing all sorts of loose particles and foreign materials and cleaning
surface thoroughly (surface preparation including thorough cleaning of surface to
(b) Providing and applying two coat of Sika Primer P in both surface of the
expansion joint followed by applying Sikaflex Construction Polyurethane based
sealant on vertical joint surface after proper fixing of the necessary backup
materials as specified and directed by the Department complete.
Rm
Rs.142.16
Rm
Rs.560.24
22.8.1 Supplying and applying of Mastercure WB1 / WB2 of Choksey Chemicals (india) Ltd.
/Dr. Sealkit Cure CC 102/ CC101 (Asian Chemicals) /MASTERKURE 106i OF BASF on
the newly placed concrete as soon as possible after the concrete is free from visible
surface water by spray method as specified and directed by the department.
Sqm
Rs.39.76
22.8.2 Supplying and applying of Concure WB of Fosroc (india) Ltd./Masterkure 107i of

BASF on the newly placed concrete as soon as possible after the concrete is free
from visible surface water as specified and directed by the department.
Sqm
Rs.52.88
Sqm
Rs.94.87
22.8 CURING COMPOUNDS:
22.9 METALLIC/ NON-METALLIC/ EPOXY BASED FLOOR HARDNER/ TOPPINGS

22.9.1 Extra for Providing and applying Lithium silicate based concrete floor hardner
Nitoflor LH of Fosroc (india) Ltd. using high volume sprayer or hand applying using
lambs wool roller as specified and directed by the department.
Page-130
Item
No.
22.9.2 Applying a floating coat of concrete floor hardner Nitoflor Hardtop or Nitoflor
Hardtop standard of Fosroc (india) Ltd. over freshly prepared concrete floors
followed by sprinkling of Nitoflor Hardtop or Nitoflor Hardtop standard and
finishing surface using power trowel as specified and directed by the department
(Concrete floor & base courses to be measured and paid separately).
(a) Heavy duty
(b) Medium duty
(c) Light duty
22.9.3 Extra for Providing Non-metallic, ready to use concrete floor hardner, Techfloor HT
200 of Choksey India Ltd. as specified and directed by the department.
Unit
Rate
Sqm
Sqm
Sqm
Rs.261.60
Rs.211.65
Rs.161.70
(a) Heavy duty
Sqm
Rs.311.72
(b) Medium duty
Sqm
Rs.247.45
(c) Light duty
Sqm
Rs.183.18
(a) Heavy duty
Sqm
Rs.494.42
(b) Medium duty
Sqm
Rs.384.03
(c) Light duty
Sqm
Rs.273.64
(a) Heavy duty
Sqm
Rs.603.84
(b) Medium duty
Sqm
Rs.453.57
(c) Light duty
Sqm
Rs.303.30
(a) Heavy duty

(b) Medium duty
(c) Light duty
22.9.5 Extra for Providing and applying 1mm self smoothing epoxy floor topping Nitoflor
SL1000 of Fosroc (india) Ltd./ MASTERTOP 1210 PLUS OF BASF using 1mm serrated
trowel and rolled with a spiked nylon roller after proper surface preparation and
application of a priming coat of Nitoprime 25(M) as specified and directed by the
department (surface preparation to be measured and paid separately).
Sqm
Sqm
Sqm
Sqm
Rs.558.68
Rs.416.32
Rs.273.96
Rs.743.86
22.9.6 Extra for Providing and applying 1.5mm to 3mm self smoothing epoxy floor topping
Nitoflor SL2000 of Fosroc (india) Ltd./ MASTERTOP 1230 PLUS of BASF using
serrated trowel and rolled with a spiked nylon roller after proper surface
preparation and application of a priming coat of Nitoprime 25(M) as specified and
directed by the department (surface preparation to be measured and paid
separately).
Sqm
Rs.1,219.89
22.9.7 Extra for Providing and applying low build polysulphide-epoxy floor coatings,
Techfloor LBC-140 of Choksey (india) Ltd. using brush or lambs wool roller after
proper surface preparation and applying techfloor primer coat complete as
specified and directed by the department (surface preparation to be measured and
paid separately).
Sqm
Rs.442.62
22.9.3.1 Cement Grey Shade
22.9.3.2 Dark Shade
22.9.3.3 Light Shade
22.9.4 Extra for Providing Non-metallic, ready to use concrete floor hardner, Chapdur of
Sika India Ltd./ MASTERTOP 100 of BASF as specified and directed by the
department.
Page-131
Item
No.
22.9.8 Extra for Providing and applying high build polysulphide-epoxy floor coatings,
Techfloor HBC-150 of Choksey (india) Ltd. using medium pile roller or a squeegee
after proper surface preparation complete as specified and directed by the
department (surface preparation to be measured and paid separately).
Unit
Rate
Sqm
Rs.1,189.89
22.9.9 Extra for Providing and applying self leveling polysulphide-epoxy floor topping
Techfloor SL-2 of Choksey (india) Ltd. /Dr. Sealkit EPU Floor Self L (Asian Chemicals)
using steel trowel and rolled after proper surface preparation as specified and
directed by the department (surface preparation to be measured and paid
separately).
Sqm
Rs.1,295.60
22.9.10 Providing and applying normal setting, self levelling epoxy modified cementitious
floor topping Sikafloor 81 EpoCem of Sika (india) Ltd. using trowel followed by
applying self smoothing epoxy floor coating Sikafloor 261(S) of Sika (india) Ltd. /Dr.
Sealkit EPU Floor Self L (Asian Chemicals) / MASTERTOP 542 ECC of BASFusing
serrated trowel and rolled with a spiked nylon roller after proper surface
preparation and application of a priming coat of Sikafloor 80 Primer as specified
and directed by the department (surface preparation to be measured and paid
separately).
22.1 REPAIR AND REHABILITATION OF STRUCTURES:
22.10.1 Repairing of spalled concrete in columns by the following processes as specified
and directed by the department complete at all levels:
A. Chipping of deteriorated concrete and removal of all loose & friable materials
and fully exposing rusted reinforcement followed by proper cleaning and removing
of rusts and other foreign materials using sand blasting/ emery cloths/ wire brush
etc.
Sqm
Rs.2,024.16
Sqm
Rs.88.13
B. Corroded reinforcement to be replaced by cutting and welding new

reinforcement of minimum 25mm dia. and overlapping on both side as specified
and directed.(reinforcement bar to be measured and paid separately).
Rm
Rs.110.87
C. Applying two coats of cement based polymer modified anti-corrosive protective

coating over exposed reinforcement including proper curing for minimum 24 hours.
Rs.405.73
D. Applying Epoxy based bonding agent Master Bond EP of Choksey /Concresive

1414 of BASF/Dr. Sealkit Bond OTN (Asian Chemicals) after totally saturating the
cleaned concrete surface with clean water for proper bonding of old and new
concrete.
Sqm
Rs.716.02
E. Concreting the column with 1:1.5:3 (1cement : 1.5coarse sand : 3aggregate) or M20 grade concrete admixed with a normal plasticizer like Master Plast PL-1/Dr.
Sealkit Normal Plast (Asian Chemicals) @ 0.2%-0.5% by weight of cement after
making the concrete fibre reinforced for reducing the effect of thermal expansion
by mixing concrete with Recron 3S @ 1.25kg per bag of cement followed by proper
curing for minimum 28days (Formwork to be measured and paid separately).
Cum
Rs.7,153.94
F. Plastering with high rich polymer modified mortar 10mm thick with cement sand
mortar in prop. 1:4 mixed with 100% acrylic polymer Master Crete M-81 /Dr.
Sealkit Sealcrete (Asian Chemicals) / RHEOMIX 131 of BASF @ 15% by weight of
cement followed by proper curing as specified and directed by the Department
complete.
22.10.2 Repairing of spalled concrete in slabs/ chajjas etc. by the following processes as
specified and directed by the department complete at all levels:
Sqm
Rs.204.48
etc.
Sqm
Rs.88.13
Page-132
Item
No.
Unit
B. Applying two coats of cement based polymer modified anti-corrosive protective

coating Thoro Stucturite Primer of BASF over exposed reinforcement including
proper curing for minimum 24 hours.
Rate
Rs.405.73
C. Applying Epoxy based bonding agent Master Bond EP of Choksey /Concresive

1414 of BASF/Dr. Sealkit Bond OTN (Asian Chemicals)/Rheomix 141 of BASF after
totally saturating the cleaned concrete surface with clean water for proper bonding
of old and new concrete.
Sqm
Rs.716.02
D. Concreting the slab/ chajja etc. with concrete admixed with a normal plasticizer
like Master Plast PL-1 /Dr. Sealkit Normal Plast (Asian Chemicals) @ 0.3% by
weight of cement after making the concrete fibre reinforced for reducing the effect
of thermal expansion by mixing concrete with Recron 3S @ 1.25kg per bag of
cement followed by proper curing (Formwork & concrete to be measured and paid
separately).
Cum
Rs.1,978.70
E. Applying two coats of 2mm thick slurry of 100% pure acrylic polymer like Master
Crete M-81/Dr. Sealkit Sealcrete (Asian Chemicals) mixed with ordinary portland
cement in prop. 1:2.
Sqm
Rs.373.54
F. Plastering with 20mm thick cement sand mortar in prop.1:4 mixed with integral
waterproofing compounds like Master Proof IWP-1 of Choksey Chemicals /Dr.
Sealkit No.1 (Asian Chemicals) @ 0.2% by weight of cement conforming to IS:2465
as specified and directed by the Department complete.
Sqm
Rs.370.88
etc.
Sqm
Rs.100.51

Rm
Rs.110.87
C. Applying two coats of single component epoxy zinc primer Nito Primer Zinc Rich
90 of Fosroc chemicals with brush over cleaned reinforcement.
Sqm
Rs.147.56
D. Providing and fixing shear connectors of 8mm dia. by drilling 14mm dia. holes on
the concrete surface to a depth of 75mm using a rotary cum hammering drilling
machine as per specification and thoroughly cleaning the hole using compressed air
and water jet and anchoring with polyester resin anchor grout Lokfix P of Fosroc
chemicals./ Masterflow 935 of BASF
E. Providing and fixing sacrificial Zinc anode, Galvashield XP of Fosroc chemicals
with reinforcement bars @ 1 unit per 0.5m run of reinforcement, tightened using a
suitable wire-twisting tool restricting free movement and ensuring good electrical
continuity.
Each
Rs.145.75
Rm
Rs.1,772.38
F. Supplying, mixing and applying a epoxy resin based bonding agent like Nitobond EP/ B CONCRESIVE 1414 of BASF for proper bond of old to new concrete .
Sqm
Rs.813.05
G.(i) Applying structural grade prepacked polymer modified cementitious mortar

Renderoc S2/Emaco S88T of BASF for application thickness upto 20mm overhead/
30mm verticals, after proper mixing with clean water followed by proper curing for
minimum 28days (Formwork to be measured and paid separately).
Cum
Rs.81,852.61
Page-133
Item
No.
Unit
Rate
G (ii). Applying structural grade prepacked polymer modified cementitious mortar

Renderoc HB2/Emaco S48CT of BASF for application thickness upto 50mm
overhead/ 80mm verticals, after proper mixing with clean water followed by
proper curing for minimum 28days (Formwork to be measured and paid
separately).
Cum
Rs.140,144.25
G.(iii) Applying and placing cementitious micro-concrete Renderoc RG/Emaco S46T

of BASF after proper mixing with clean water after erection of formwork followed
by proper curing for minimum 28days (Formwork to be measured and paid
separately).
Cum
Rs.69,317.07
etc.
Sqm
Rs.100.51
B.(i) Applying two coats of single component epoxy zinc primer Nito Primer Zinc
Rich 90 of Fosroc chemicals with brush over cleaned reinforcement.
Sqm
Rs.147.56
B.(ii) Applying two coats of single component epoxy zinc primer Concresive ZRI of
BASF India Ltd, a two component, epoxy zinc rich. It shall be formulated to meet
the requirement of BS 4652 Type 2. The primer shall be an active type having zinc
content of greater then 90% in dry film state which is capable of negating the
generation of incipient anodes in the areas surrounding the repairs. The product
shall have mix density not less than 2.25 kg/litre. It shall be fully compatible with
EMACO Range of repair mortars. with brush over cleaned reinforcement.
Sqm
Rs.266.62
C. Providing and fixing sacrificial Zinc anode, Galvashield XP of Fosroc chemicals

with reinforcement bars @ 1 unit per Sqm of reinforcement, tightened using a
suitable wire-twisting tool restricting free movement and ensuring good electrical
continuity.
Sqm
Rs.895.02
D. Supplying, mixing and applying a epoxy resin based bonding agent like Nitobond EP/ CONCRESIVE 1414 of BASF for proper bond of old to new concrete .
Sqm
Rs.813.05
E. (i) Applying cement sand mortar (prop.1:4) admixed with mortar modifier cum
bonding agent Nitobond SBR of Fosroc Chemicals/Rheomix 141 of BASF @ 5Ltrs per
bag of cement as specified.
Cum
Rs.492.33
E.(ii) Applying and placing cementitious micro-concrete Renderoc RG/Emaco S46T

of BASF after proper mixing with clean water after erection of formwork followed
by proper curing for minimum 28days (Formwork to be measured and paid
separately).
Cum
Rs.69,317.07
E.(iii). Concreting the slab/ chajja etc. with concrete 1:1.5:3 (1cement : 1.5coarse
sand : 3aggregate) or M-20 grade admixed with Conplast P211 of fosroc chemicals
@ 150ml per bag of cement followed by proper curing (Formwork & concrete to be
Cum
Rs.5,598.90

Page-134
Item
No.
Unit
Rate
etc.
Sqm
Rs.88.13

Rm
Rs.123.25
C.(i) Applying two coats of cement based polymer modified anti-corrosive

protective coating Sika Top Armatec 108 of Sika (India) Ltd. over exposed
reinforcement including proper curing for minimum 24 hours.
Sqm
Rs.61.00
C.(ii) . Applying two coats of cement based polymer modified anti-corrosive

protective coating Sika Topseal of Sika (India) Ltd. over exposed reinforcement
including proper curing for minimum 24 hours.
Sqm
Rs.69.52
D. Applying Epoxy based bonding agent Sikadur 32 LP @ 250gms per sq.m. per coat
for proper bonding of old and new concrete.
Sqm
Rs.411.71
E. Applying and placing cementitious micro-concrete Sika Rep by proper mixing

with clean water after erection of formwork followed by proper curing for
minimum 28days (Formwork to be measured and paid separately).
Cum
Rs.59,059.65
etc.
Sqm
Rs.88.13
B. (i) Applying two coats of cement based polymer modified anti-corrosive

protective coating Sika Top Armatec 108 of Sika (India) Ltd./ THORO STRUCTURITE
PRIMER of BASF over exposed reinforcement including proper curing for minimum
24 hours.
Sqm
Rs.61.00
B.(ii) Applying two coats of cement based polymer modified anti-corrosive

protective coating Sika Topseal of Sika (India) Ltd./Dr. Sealkit Flexibond AP 121 C
(Asian Chemicals) over exposed reinforcement including proper curing for
minimum 24 hours.
Sqm
Rs.69.52
C. Applying Epoxy based bonding agent Sikadur 32 LP/Dr. Sealkit Bond OTN (Asian
Chemicals) @ 250gms per sq.m. per coat for proper bonding of old and new
concrete.
Sqm
Rs.411.71
D. Providing, supplying and placing of two component Polymer Modified Mortar

Sika Top 122 after erection of formwork as per specification.
Cum
Rs.9,963.00
Sqm
Rs.1,115.96
22.11 STRENGTHENING OF COLUMNS, BEAMS & SLABS:

22.11.1 Restrengthening of RCC members by the following processes as specified and
directed by the department complete at all levels:
A. Doing patch work in depression of concrete surface wherever necessary by
laying epoxy putty, Nitocote VF of Fosroc Chemicals as specified & directed by the
Department complete after proper surface preparation and proper scraping of
concrete protrusion (surface preparation including thorough cleaning of surface to
Page-135
Item
No.
Unit
Rate
B. Applying of Nitowrap 410 saturant with wet film thickness @ 250 microns over a
coat of saturant epoxy primer Nitowrap 30 of fosroc chemicals with brush followed
by fixing of Carbon fibre composite system Nitowrap EP(CF) by pressing on the
saturant and impregnate the same by applying a final coat of Nitowrao 410 as
specified and directed by the department.
(i). In Columns
(ii). In Slabs & Beams
C. Applying of two coats of two component UV resistant coating Nitowrap 512 over
fibre system having wet film thickness of 100 micron as specified and directed by
the department.
(i). In Columns
(ii). In Slabs & Beams
Sqm
Sqm
Rs.3,628.21
Rs.3,658.41
Sqm
sqm
Rs.2,799.20
Rs.2,843.20
Sqm
Rs.1,614.10
(i). In Columns :
Supply and Application of MBrace CF 230 - Unidirectional Carbon Fiber
Reinforcement System of BASF India Ltd having 400Gm/sq.mt weight and having
Modulus of elasticity of 240 kN/mm at the entire length of the beam with one
layer after proper application of Concresive 2200 at the entire beam area at a
thickness of 2mm, which will be followed by the application of Mbrace saturant
after proper curing of Concresive 2200. Mbrace fiber to be applied over Mbrace
Saturant at the green condition and after proper wrapping the secod layer of
Mbrace Saturant to be applied. Sand to be broadcasted over the Mbrace saturant
layer in green condition for application of any top screed or plastering.
Sqm
Rs.4,707.56
(ii). In Slabs & Beams:

Supply and application of Ready to use Carbon laminates (Fibre Reinforced
Polymer) for the reinforcement of concrete elements with MBrace FRP Laminate of
165/2500,50mm wide & 1.4mm thick System at the bottom portion of the beam,
after application of Mbrace Laminate Adhesive , which is having minimum 2.5Mpa
adhesion strength.
Rm
Rs.3,451.77
(iii) Strenghtening With Glass Fibre
Sqm
Rs.2,653.10
Sqm
Rs.1,307.32
22.11.2 Restrengthening of RCC members by the following processes as specified and

directed by the department complete at all levels:
A. Doing patch work in depression of concrete surface wherever necessary by
laying epoxy putty, Concresive 2200 of BASF India Ltd. as specified & directed by
the Department complete after proper surface preparation and proper scraping of
concrete protrusion (surface preparation including thorough cleaning of surface to
B. Applying of MBRACE Fibre strengthening system of BASF India Ltd including
laminate and sheet products for increasing the strength of concrete structures.
Carbon, Aramid and E-glass can be used to solve problems from change of use to
increased load carrying capacity.
22.13 Providing applying "XYPEX" Concrete Waterproofing & Durability Enhancement by

Crystallization" to be supported by at least two International Test reports showing
clear Scanning Electron Microscopic (SEM) photographs of desified and mature
crystals forming to plug all the capilary tracks and pores of the concrete
permanently and permeability test as per IS 2720 conducted by CBRI. The concrete
should not absorb water more than a.5 grams and not more than 1 mm from the
concrete surface. The product to be listed in ICC-ES-EVALUATION REPORT INDEX
January 2009. The treatment to be carried out on the concrete surfaces as per
manufacture's specification
Page-136
CH-23: DISMANTLING AND DEMOLISHING

Item
No.
DISMANTLING WORKS
23
23.1 Demolishing lime concrete without damaging the structure and disposal of debris
as directed at all levels
Unit
Rate
Cum
Rs.160.11
(i) Prop (1 : 4 : 8) or leaner mix

(ii) Prop (1 : 3 : 6) or richer mix
23.3 Demolishing RCC work including stacking of steel bars and disposal of unserviceable
material as directed for all levels
Cum
Cum
Cum
Rs.313.80
Rs.545.40
Rs.767.20
23.4 Demolishing RB work including stacking of steel bars and disposal of unserviceable
material as directed for all levels
Cum
Rs.673.40
23.5 Extra for cutting reinforcement in RCC or RB work at all levels (Payment to be made
on cross sectional area of RCC or RB work obtained by multiplying the length of the
cut reinforcement and thickness of the member).
Sqm
Rs.402.80
23.6 Extra for scraping, cleaning and straightening reinforcement from RCC or RB work
at all levels
Kg.
Rs.1.90
23.7 Demolishing brickwork including stacking of serviceable materials and disposal of

unserviceable materials as directed for all levels
Cum
Rs.435.60
23.8 Demolishing stone rubble masonry including stacking of serviceable materials and
disposal of unserviceable materials as directed for all levels
Cum
Rs.522.90
23.9 Dismantling wood work in frames, trusses, purlins and rafters including stacking the
materials as directed by the department for all levels.
Cum
Rs.1,050.20
23.10 Dismantling steel work in single sections (R.S.Joists, channels, angles, tees and flats
etc.) including dismembering and stacking the materials as directed by the
Department for all levels.
Kg.
Rs.1.10
23.11 Dismantling steel work in built up sections in joists, angles, channels, tees, flats etc.
including all gusset plates, bolts, nuts, cutting rivets, welding etc. including
dismembering and stacking the materials as directed by the Department for all
levels
Kg.
Rs.2.20
23.12 Dismantling all types of corrugated/ trapezoidal sheet roofing including ridges, hips,
valleys and gutters etc. and stacking the materials as directed by the department
for all levels
Sqm
Rs.34.20
23.13 Demolishing skirting/ dado in walls/ R.C.C. & P.C.C. members without causing
damage to walls/ member upto any height including disposal of debris as directed
for all levels
Cum
Rs.3,849.90
23.14 Demolishing the plastering from walls/ R.C.C. and P.C.C. members without causing
any damage to the wall/ member upto any height including disposal of debris as
directed for all levels.
Cum
Rs.3,339.00
23.15 Demolishing CC floors of various thickness including top layer and base course and
disposal of debris as directed for all levels.
Sqm
Rs.102.60
23.16 Demolishing mosaic floor of various thickness, both mosiac tiles and cast-in-situ
type including CC base course and removal of debris as directed for all levels.
Sqm
Rs.138.80
23.2 Demolishing plain cement concrete including disposal of debris as directed for all
levels
Ch-23 : Dismantling Works
Page-137
Item
No.
23.17 Demolishing R.C.C./ P.C.C. pile head of different diameters carefully without
disturbing the remaining portion of the pile including opening out of the pile head
to be demolished by excavating the earth upto required depth and clearing the
debris as directed.
Unit
Rate
Cum
Rs.707.90
(i) Area of door/window up to 3.00 m2
Each
Rs.64.65
(ii) Area of door/window above 3.00 m2
Each
Rs.102.47
23.19 Dismantling of existing steel windows/ steel ventilators/ steel windows and steel
ventilators without damaging the walls, removing to a safe place and necessary
repairs to the edges of walls.
Sqm
Rs.101.20
23.20 Dismantling all types of ceiling, partition and wall lining and stacking the materials
as directed by the department for all levels
Sqm
Rs.22.40
23.18 Dismantling and removing the existing door and window frame (chowkath) both
wooden and steel of different sizes without damaging the walls and removing the
frame and necessary repairs to the edges of the walls as directed for all levels.
Ch-23 : Dismantling Works
Page-138
CH- 24: BAMBOO & WIRE-NETTING WORKS

Item no
24
Description
Unit
Rate
BAMBOO AND WIRE NETTING WORKS
24.1
Spilt bamboo diagonally woven wall tied with necessary bamboo kamis on both
sides @300mm apart tied with galvanised wire/cane slit etc complete as directed.
Sq.m
Rs.176.07
24.2
Bamboo slit walling in timber frame with bamboo slit fitted in to the grooves of the
timber frame and stiffened by means of double bamboo slits 25mm wide and not
less than 6mm thick spaced at intervals of not more than 400mm apart one slit
attached on each side and tied together by means of cane slit/galvd tying wire
including 20mm thick cement plaster in prop 1 cement : 6 fine sand on both sides in
two coats with curing etc complete (measurement for timber frame shall be
Renewing / providing single tarja enclosure walls made of Muli / jati bamboo with
mature Baruah / Bhaluka bamboo ( 87 mm to 100 mm dia) posts 1300 mm apart
and 1800 mm height (approx) above ground and driven 750 mm below ground
stiiffened with Muli / Jati bamboo kamis on both the faces 4 lines, including
supplying and tying with galvd.wire complete as directed.
Sq.m
Rs.410.34
Sq.m
Rs.134.00
24.4
Renewing / providing Muli / Jati bamboo double tarja enclosure walls with Baruah
/ Bhaluka bamboo 87 mm to 100 mm dia.1800 mm apart and 1800 mm height
(approx) above ground and driven 750 mm below ground and half Muli / Jati
bamboo on both the faces 4 lines, including supplying and tying with galvd.wire
Sq.m
Rs.242.24
24.5
Renewing / providing double lattice pattern fencing with mature Baruah / Bhaluka
bamboo posts 87 mm to 100 mm dia., 950 mm to 1050 mm above ground and
minimum 600mm below ground and 4 lines of double kamies with half round Muli
/ Jati bamboo on top including supplying and tying with galvd.wire complete as
directed.
Sq.m
Rs.61.57
24.6
Providing jail enclosure wall with matured Jati / Bhaluka / Makhal bamboo 60 mm
to 75mm dia.and of height of 3000 mm including taking out and refitting the old
timber battens with old and new bolts and nuts, nails etc. and coaltaring (Indoor
Coat) two coats on the bamboos and battens and removing and stacking the old
materials in proper places as per direction of the deptt.out side the jail compound
walls.
Sq.m
Rs.480.24
24.7
Providing bamboo sleeping machang with necessary Bhaluka bamboo post etc.
complete.
Sq.m
Rs.254.49
24.8
Providing, fitting, fixing 20 mmx 50 mm mesh expanded metal wall of 18 gauge (1.2
mm thickness) in sal wood dressed frame not more than 1.20 m centre to centre
including sal wood beading of 50 mm x 25 mm size sides chamfered , fitted with
necessary wood screws spaced not more than 400 mm apart etc. complete as
directed (sal wood frame to be measured and paid separately).
Sq.m
Rs.425.65
24.9
Providing, fitting and fixing wire netted wall with 13 mm hexagional mesh made of
20 gauge (0.95mm) over hollock wood dressed frame not more than 600 mm apart
including hollock wood beading of 50 mm x 25 mm size sides chamfered , fitted
with necessary wood screws spaced not more than 300 mm apart etc. complete as
directed (Hollock wood frame to be measured and paid separately).
Sq.m
Rs.513.68
24.3
Ch-24 : Bamboo and Wirenetting Works
Page-139
Item no
Description
Unit
Rate
24.10 Providing fly proof M.S. wire netting of I.S.gauge designation 85 with wire of dia
0.05 mm over hollock or other wood dressed frame including 1st class timber
beading of 38mmx12 mm size chamfered including fitting, fixing with necessary
wood screws etc.complete as directed (timber frame to be measured and paid
separately).
Sq.m
Rs.471.36
24.11 Providing bird proof hexagional galvanised wire netting at ceilling level of Assam
type building including fitting and fixing with first class local wood frame of size
50mm x 25mm and beads of size 25mm x 10mm (for fitting and fixing the net with
wooden frame ) including lifting and fitting the same in position etc. complete as
directed including two coats kiricide oiling of timber works.
Sq.m
Rs.185.55
Ch-24 : Bamboo and Wirenetting Works
Page-140
CH-25: MISCELLANEOUS WORKS

Item
No.
25
25.1
25.2
25.3
25.4
Unit
Rate
MISCELLENEOUS WORKS
Construction of temporary shed with 300mm high plinth and floor , Bhaluka
bamboo post driving at least 750mm under ground, height above plinth
2400mm,wattle wall mud plastered and white wash two coats, 100mm thick
thatched roof, double mat doors and windows etc. complete as directed as
specified.
a). With whole Jati bamboo rua frame
Sqm
Rs.621.79
b). With Jati bamboo kami frame
Sqm
Rs.557.37
(a). With 50mm x 6mm F.I. Double strap.
Set
Rs.357.57
(b). With 45mm x 6mm F.I. Double strap.
Set
Rs.221.99
(a). Light jungle.
Sqm
Rs.0.79
(b). Mediuum jungle.
Sqm
Rs.1.61
Supplying fitting and fixing 750mm long F.I.double straps at the bottom of timber
posts with 16mm dia. double bolt and nuts and 550 mm length of straps to be
embedded in cement concrete pillar in prop 1:3:6 and balance 200 mm length to
remain above with bottom 75 mm to be bent at right angles etc. complete as
directed (C.C work to be paid separately)
Jungle clearing including cutting bamboo and trees below 500mm girth and
removing the same outside the limit as directed.
Felling and removing

a). Bamboo clumps
Sqm
Rs.77.69
b). Bamboo clumps including uprooting stumps.
Sqm
Rs.108.49
(i).500 mm to 1000mm girth.
Each
Rs.77.58
(ii).1000 mm to 1500mm girth.
Each
Rs.154.57
(iii).1500 mm to 1800mm girth.
Each
Rs.306.80
(iv).1800mm girth and above
Each
Rs.610.69
d) Tea bushes
Each
Rs.8.05
e) Tea bushes including uprooting
Each
Rs.17.03
f).Cutting and clearing bushes consisting of plants and all sorts of bambooes
including uprooting and removing as necessary and filling up the holes with
earth,dressing,ramming etc. complete.
Sqm
Rs.11.08
Surface dressing of ground including removing vegitation and/ or undulation of

ground not exceeding 150mm deep and disposal of rubbish outside the periphery
and lift up to 1800mm in all kinds of soil.
Sqm
Rs.4.69
Jungle clearence including uprooting of vegitation, grass, brush-wood, sapling and

trees not exceeding 300mm girth and disposal of the same outside the periphery
and lift upto 1500mm
Sqm
Rs.5.47
Each
Rs.1,044.14
c).Cutting trees including uprooting and removing where necessary.
N.B.- All girth measurement for trees are to be taken at 1200 mm height above the
ground.
25.5
25.6
25.7
Cutting down trees where the building is to beconstructed of girth exceeding

300mm, grubb ing up roots, filling pits and levelling off ground lopping branches,
trimming and removeing to distance beyond 30m and stacking serviceable
materials and cleaning site etc. as directed.
i).Girth exceeding 300mm but not exceeding 1000mm
Ch-25 : Miscellaneous Works
Page-141
Item
No.
25.8
25.9
Unit
Rate
ii).Girth exceeding 1000mm but not exceeding 1500mm
Each
Rs.1,810.01
iii).Girth exceeding 1500mm but not exceeding 2000mm
Each
Rs.1,927.28
iv).Girth exceeding 2000mm but not exceeding 2500mm
Each
Rs.2,383.63
v).Girth exceeding 2500mm but not exceeding 3000mm
Each
Rs.2,606.98
(a).25mm bore - 300mm long.
Each
Rs.57.53
(b). 40mm bore - 300mm long.
Each
Rs.57.53
(a) 15mm diameter
Each
Rs.144.24
(b) 20mm diameter
Each
Rs.145.70
(c) 25mm diameter
Each
Rs.159.96
(d) 32mm diameter
Each
Rs.171.95
(e) 40mm diameter
Each
Rs.182.45
Rm
Rs.123.66
Each
Rs.784.35
a) 100mm thick slab
Sqm
Rs.1,410.90
b) 75mm thick slab
Sqm
Rs.1,277.11
(a) 200 mm thick in foundation and substructureup to plinth level in cement morter
(1:6)
Sqm
Rs.628.98
(b) 200 mm thick in super structure in cement morter (1:6)

(c) 100mm thick in super structure in cement morter (1:4)
Sqm
Sqm
Rs.642.36
Rs.629.15
Providing and fixing galvd. / M.S. tube (light grade) outlet (spout) in cement mortar
1:3 including cutting and making good the wall
Providing 200mm to 450mm long G.I. pipe spout embedded in C.C./ brick works for
drainage of water as per direction of the Department including necessary breaking
and repair and sealing of joints for all levels.
25.10 Supplying fitting and fixing 200mm x 6mm thick A.C. plain sheet for vertical and
horizontal expansion joints fixed to one side of column/ wall by necessary rawal
plugs/ screws/ wooden plugs placed not more than 300mm c/c as directed and
specified.
25.11 Supplying, fitting and fixing in position R.C.Cboundary pillers of size 150mm x
150mm x.1500mm long, 750mm above ground and 750mm below ground,
including square base of 450mm x 450mm x 150mm with 4 nos.12mm MS rods
main reinforcement and 6mm MS stirrups at 300mm centres tied in position with
annealed binding wire, cement concrete proportion 1:2:4 with broken stone
aggregate upto 20mm size including cantering moulding the top,curing,6mm thick
cement plastering in proportion 1:3,painted black and white alternately in 230mm
strips upto 750mm from the top keeping necessary grooves etc. as per design and
direction complete.
25.12 Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:2:4 reinforced
with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black
annealed wire with necessary shuttering , curing etc. complete including fixing in
position as directed.
25.13 Precast concrete block masonry (includingquoin blocks, jamb blocks, closure etc.)
withhollow cement concrete blocks of approvedsize conforming to I.S. 2185 - 1965
with1:3:6mix (1cement: 3 coarse sand: 6 graded stoneaggregate , 20 mm and down
gauge) having solid materials not less than 50% total volumeof block including
Page-142
Item
No.
25.14 Precast concrete block masonry (includingquoin blocks, jamb blocks, closure etc.)
withhollow cement concrete blocks of approvedsize conforming to I.S. 2185 - 1965
with1:6mix (1cement: 6 graded stone aggregate, 20 mm and down gauge) 1/4th
having solid materials not less than 50% total volume of block including curing
Unit
Rate
(a) 200 mm thick in cement sand mortar(1:6) in foundation and substructure upto
plinth level
Sqm
Rs.628.98
(b) 200 mm thick in super structure in cement morter (1:6)
Sqm
Rs.644.45
(c) 100mm thick in super structure in cement morter (1:4)
Sqm
Rs.490.79
i).From 300 mm to 600 mm dia.
Rm
Rs.39.66
ii).From 600 mm to 900 mm dia.
Rm
Rs.123.33
iii).From 900 mm to 1200 mm dia.
Rm
Rs.184.88
25.16 Labour for fitting and fixing single emptybitumen drum in culvert after cutting to
proper sizes and fitting in position including allcarriage.
Rm
Rs.64.45
25.17 Labour for fitting and fixing double emptybitumen drum in culvert after cutting to
proper sizes and fitting in position including allcarriage.
Rm
Rs.126.36
Sqm
Rs.1,562.91
(b) 30mm wide
Sqm
Rs.1,691.68
(c ) 40mm wide
Sqm
Rs.1,889.33
(d ) 50mm wide
Sqm
Rs.2,090.98
(e ) 75mm wide
Sqm
Rs.2,809.30
25.15 Labour for fitting and fixing hume pipes inpositions with coal tar immediately
includingcaulking and joining pieces with cement mortarof proportion 1:3 as per
direction of theDepartment including all carriage.
Expansion Joint Filler Board

25.18 Providing and fixing Duraboard HD-100 premoulded compressible filler board at all
heights and depths of minimum density 95kg/cum, non-staining having less than
1% water absorption, compression recovery of 93% (minimum) as per
manufactured specification with polysulphide sealant to seal the expansion joint
including preparation of surface, Polymer Modified Mortar (PMM) (Proportion
1cement: 3 sand:1 acrylic polymer) nozing, carriage of materials, cutting and
placing to the required size complete at all levels as per drawings and direction of
Engineer-in-Charge.
(a) 25mm wide
Page-143
CH-26: ANTI-TERMITE TREATMENT

Item
No.
Unit
Rate
26.1 PRE CONSTRUCTION ANTI - TERMITE TREATMENT

26.1.1 Pre construction anti - termite treatment at the bottom of foundation pits and
walls on either side up to a height of 300mm from bottom of the excavation made
for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five)
litres per square meter of the surface area before starting construction work
(supplying of necessary tools and accessories by the contractor) as per the
direction of the Department complete.
a) with aqueous emulsion having concentration 1:19 with chloropirophose solution
(tricel or euivalent) and water, i.e. 1% solution.
Sqm
Rs.77.09
b) with aqueous emulsion having concentration 1:499 with Premise 350 SC

(Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.
Sqm
Rs.37.88
26.1.2 Pre construction anti - termite treatment in the back fill in immediate contact with
the foundation structure after completion, column, wall etc. to a depth of 450mm
and width 300mm (when required refill in 200mm thick layers) applying the
emulsion @ 5 (five) litres per square meter towards the concrete and masonry
walls so as to ensure earth in contact with the structure well treated - with
chemical (supplying of necessary tools and accessories by the contractor) as per
the direction of the Department complete.
Sqm
Rs.77.09

Sqm
Rs.37.88

Sqm
Rs.77.09

Sqm
Rs.37.88

Sqm
Rs.168.27

Sqm
Rs.81.99
26.1.3 Pre construction anti - termite treatment by applying in the entire levelled area
after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres
per square meter of the surface to be spread with light rodding so as to ensure
proper absorption by the filled up earth (supplying of necessary tools and
accessories by the contractor) as per the direction of the Department complete.
26.1.4 Pre construction anti - termite treatment by applying in the junction of walls,
column with the floor before laying floor and after operation of item no. 26.1.3
above making a channel 30mmx30mm all over the walls and making rod holes @
150mm apart up to ground level below and applying emulsion @ 11 litres per
square meter of vertical plinth wall surface inside the building so as to soak the soil
with the emulsion up to the ground level and refill the holes and channel with the
original materials obtained in making channels (supplying of necessary tools and
accessories by the contractor) as per the direction of the Department complete.
Ch-26 : Antitermite Works
Page-144
Item
No.
26.1.5 Pre construction anti - termite treatment by applying the soil along the external
perimeter of the building (after construction completed) to a distance close to the
plinth wall as specified and as directed by the deptt. up to a depth of 300mm
making rod holes along the line @ 150mm apart to a depth of 300mm and applying
emulsion @ 4.5 litres per running meter ensure moistening of the soil with
emulsion (supplying of necessary tools and accessories by the contractor) as per
the direction of the Department complete.
Unit
Rate

R.M
Rs.69.90

R.M
Rs.34.60
i) with aqueous emulsion having concentration 1:19 with chloropirophose solution

Rm
Rs.14.63
ii) with aqueous emulsion having concentration 1:499 with Premise 350 SC
Rm
Rs.8.74

Rm
Rs.18.40
Rm
Rs.10.55

Sqm
Rs.44.75
Sqm
Rs.23.39
26.2 POST CONSTRUCTION ANTI - TERMITE TREATMENT

26.2.1 Diluting and injecting aqueous emulsion for post constructional anti - termite
treatment (necessary tools and accessories to be supplied by the contractors).
a)
b)
c)
d)
Along external wall (where apron is not provided) in the vertical surface of the
substructure to a depth of 300mm including excavation channel along the wall and
rodding etc. by applying the emulsion at 2.5 litres per square meter complete as
Along the external wall below concrete or masonry apron using aqueous emulsion
having concentration 1:19 with chloropirophose solution (tricel or equivalent) and
water @ 1 litre per liner metre including drilling and plugging holes (minimum
depth of hole should be 300mm).
Treatment of soil under existing floors using aqueous emulsion having

concentration 1:19 with chloropirophose solution (tricel or equivalent) and water
@ 0.50 litre per hole, 300mm apart including drilling 12mm diameter holes and
plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing
floor. (Cement mortar to be measured and paid separately). (Minimum depth of
hole should be 300mm).
Treatment of existing masonry using aqueous emulsion having concentration 1:19

with chloropirophose solution (tricel or equivalent) and water @ 0.5 litre per hole,
300mm apart including drilling holes at 45 degree and plugging them with cement
mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole. (Minimum
depth of hole should be 300mm).
Page-145
Item
No.
e)
Unit
Rate

Rm
Rs.22.17
Rm
Rs.12.36

Rm
Rs.46.42
Rm
Rs.24.20
Treatment at points of contact of wood work by aqueous emulsion having

concentration 1:19 with chloropirophose solution (tricel or equivalent) and water
@ 0.50 litre/hole by drilling 6mm dia holes at downward angle of 45 degree at
150mm centre to centre and sealing the same.
Page-146
CH-27: REPAIRING WORKS

Item
No.
27.1
27.2
27.3
Description
Taking out from position and repairing steel window shutters including steel
frames at all levels after cutting out the heavily rusted and damaged portion of the
shutters and frames and welded with the new 'Z' section of steel members, corner,
hinges, stay etc. including fitting and fixing in position and riveting with new rivets
adjusting, cleaning, cutting the holes and making good the damages to metal with
existing one. Window grills to be removed during carrying out the work and to be
re-fixed in position after completion of work. The glass panes damaged during
execution should also be changed.
Strengthening of beam, columns, lintels, chajjas, slabs by applying water proofing
treatment, exposed reinforced treatment, sealant application by Micro concrete
CNS 100 + M - 81 up to 15mm complete as directed by the Department at all
levels.
Supplying, fitting and fixing 4mm thick teak plywood sheet after removing the
existing damaged teak ply, over timber frame with Fevicol, nails, screws etc.
including cutting sheets to proper sizes etc. complete as directed at all levels.
Ch-27 : Repairing Works
Unit
Rate
Sqm
Rs.835.30
Sqm
Rs.460.60
Sqm
Rs.1,345.00
Page-147
CH-28: QUALITY CONTROL

Item
No.
28
28.1
Description
Unit
Rate
Collection from the field and testing in the laboratory of undisturbed soil sample
for sub-soil investigation (as per relevant I.S. code) by open drive sampler (100 mm
dia. Boring) through clayey soil layer/sandy soil layer/sandy clay/sandy silt
layer/clayey silt layer,conduction standard penetration test(SPT) and collection of
SPT sampler,observation of ground water table,spot level survey to the bore
location and carrying out R.L. from nearest B.M.,laboratory test (particle size
analysis,hydrometer
test,liquid
limit
determination,plastic
limit
determination,specific
gravity
determination,triaxal
test,direct
shear
test,unconfined compression test,consolidation test) including preparation of subsoil investigation report complete with necessary printing and binding (minimum 5
copies)
A. Boring.
(i) Construction of 100mm hand wash boring through all types of cycle,sandy
clay,silty sand,silty clay soil,excluding transportation charges.
Rm
Rs.666.16
(ii) Construction of 100mm machine boring (Drilling) through all types of

cycle,sandy clay,silty sand,silty clay soil,excluding transportation charges.
Rm
Rs.849.65
(iii) Construction of 100mm machine boring (Drilling) through all types of

gravel,sandy gravel excluding transportation charges.
Rm
Rs.3,186.42
(iv) Construction of 100mm machine boring (Drilling) for rock layer, excluding
transportation charges.
Rm
Rs.4,305.53
(i) Conduction of SPT at equal interval of 1.5 m or change of strata whichever is

earlier and collection of disturbed soil sample from SPT sampler including proper
airtight sealing,labelling.
(ii) Conduction of SPT by DCPT (Method dry) excluding transportation charges.
Rm
Rs.88.07
Rm
Rs.346.52
(iii) Conduction of SPT by DCPT (Method wet) excluding transportation charges.
Rm
Rs.397.36
(i) Particle size analusis (dry sieving)
per test
Rs.144.46
(ii) Particle size analusis (wet sieving)
per test
Rs.157.70
(iii) Determination of Hydrometer test.
per test
Rs.736.15
(a) 3 points
per test
Rs.230.57
(b) 2 points
per test
Rs.153.71
(v) Determination of Plastic Limit test.
per test
Rs.138.38
(vi) Determination of Moisture Content test.
per test
Rs.88.07
(vii) Determination of bulk density test.
per test
Rs.69.97
(viii) Determination of Specific Gravity test of fine grained soil..

(ix) Determination of Direct shear strength
per test
Rs.182.99
(a) 3 points
per test
Rs.474.42
(b) 2 points
per test
Rs.316.27
B. Standard Penetration Test (S.P.T.)
C. Laboratory test
(iv) Determination of liquid limit test.
Ch-28 : Quality Control
Page-148
Item
No.
Description
Unit
Rate
(x) Determination of shear strength parameters of a specimen tested in

unconsolidated undrained traiaxial compression test without measuring pore water
pressure by triaxial test.
(a) 3 points
per test
Rs.723.80
(b) 2 points
per test
Rs.482.54
(a) 3 points
per test
Rs.1,435.39
(b) 2 points
per test
Rs.956.93
(a) 3 points
(b) 2 points
(xiii) Determination of consolidation properties of Soil.
per test
per test
Rs.369.50
Rs.246.34
(a) 3 points
per test
Rs.876.23
(b) 2 points
per test
Rs.584.16
(xiv) Determination of vane shear strength.
per test
Rs.651.61
(xv) Determination of Permeability of soil by falling head method.

(xv) Determination of shear strength parameters of a specimen tested in
consolidated undrained traiaxial compression test without measuring pore water
pressure by triaxial test.
per test
Rs.950.65
(a) 3 points
per test
Rs.876.08
(b) 2 points
per test
Rs.584.06
(a) 3 points
per test
Rs.1,329.37
(b) 2 points
per test
Rs.886.25
(xvii) Determination of Swelling Index.
per test
Rs.736.15
(i) Hire charge
per day
Rs.3,811.50
(ii) Fuel
per km
Rs.17.87
A. Cement
(i) Compressive strength.
per test
Rs.199.82
(ii) Setting time..
per test
Rs.242.22
(iii) Fineness test.
per test
Rs.526.07
(iv) Impurities percentage (Bromoform test)
per test
Rs.769.08
(v) Ignition test.
per test
Rs.209.35
(vi) Specific gravity.
per test
Rs.508.85
(xi) Determination of consolidated drain test determination of the shear strength

parameters of a specimen tested in consolidated drain triaxial compression test
without measuring pore water pressure,by triaxial test.shear strength parameters
of a specimen tested in unconsolidated undrained traiaxial compression test
without measuring pore water pressure by triaxial test.
(xii) Determination of unconfied compressive strength.
(xvi) Determination of shear strength parameters of a specimen tested in

consolidated undrained undrained test compression test with measuring pore
water pressure by triaxial test.
D. Transportation on charges for boring.
28.2 Collection of sample from field and testing in laboratory/field as per relevant I.S.
codes of practice and preparation and submission of of the reports to the
concerned authority in proper format with specified no. of copies (minimum 5
copies)
Page-149
Item
No.
Description
Unit
Rate
B. Concrete
(i) Compressive strength(including moulding &curing)
per test
Rs.262.82
(ii) Compressive strength(excluding moulding)
per test
Rs.127.94
(iii) (a) Mix design
per test
Rs.8,458.55
(b) Subsequent Job Mix Design with same materials.
per test
Rs.5,686.73
(iv) Tensile strength of concrete.
per test
Rs.766.68
(i) Tensile strength of steel.
per test
Rs.507.12
(ii) Bending & Re-bending of steel.
per test
Rs.592.28
(i) Aggregate impact value test (in over size)
per test
Rs.477.23
(ii) Aggregate impact value test (in proper size)
per test
Rs.301.66
(iii) Aggregate crushing value test (in over size)
per test
Rs.590.18
(iv) Aggregate crushing value test (in proper size)
per test
Rs.497.76
(v) Los Angeles abrasion test.
per test
Rs.559.18
(vi) Flakiness index test.
per test
Rs.382.22
(vii) Specific gravity test.
per test
Rs.273.41
(viii) Water absorption test.
per test
Rs.272.77
(ix) Soundness test.(5 cycle sodium sulphate
per test
Rs.3,180.38
(x) Grading test of coarse aggregate.
per test
Rs.428.21
(xi) Grading test of fine aggregate.(including fineness modulus,gradation,P.C. of silt

and clay and silt factor)
per test
Rs.477.98
(xii) Bulk density test of coarse/fine aggregate-Loose compacted.
per test
Rs.233.65
(xiii) Bulkinf factor of fine aggregate by Lab. Method.
per test
Rs.327.64
(xiv) Bulkinf factor of fine aggregate by Field Method.
per test
Rs.144.82
(xv) Aggregate stripping value test.
per test
Rs.241.34
C. Steel
D. Aggregate
Page-150
CH-29: FIRE-FIGHTING WORKS

Item
No.
29.1
29.1.1
Description
HYDRANT SYSTEM
Providing,Fixing, testing &Commissioning of Single Headed Gun Metal ISI Marked
oblique pattern Hydrant Landing Valve with 80 mm dia, flanged inlet & 63 mm dia
instantaneous type female outlet complete with cap and chain, twist release lug
and all accessories as per IS:5290-19833 (Type-'A') and specifications complete as
reequired . (MAKE:ESSEL/WINCO/NEWAGE)
Unit
Rate
each
Rs.9,028.75
29.1.2
Providing controlled percolating (C.P.) hose ISI Marked (IS:8423) 63 mm dia X 15 M

long complete with instantaneous type Gun Metal 63 mm dia ISI Marked male &
female couplings (IS:903) bound & riveted to hose pipes with copper rivets and
copper wire complete as required.
(MAKE: NIRMAL RUBBER/NEWAGE)
each
Rs.5,602.34
29.1.3
Providing RRL Hose with ISI Marked (IS:636) 63 mm dia X15 M long complete with
instantaneous type Gun Metal 3 mm dia ISI Marked male & female couplings
(IS:903) bound & riveted to hose pipes with copper rivets and copper wire
complete as reqd.
( MAKE: NIRMAL RUBBER/NEWAGE)
each
Rs.6,044.52
29.1.4
Providing & fixing of weather proof hose cabinets fabricated from 16 S.W.G. M.S.
Sheet with centre opening full front glass door and locking arrangement, suitable to
accommodate one landing valve (Yard Hydrant ), 2nos.15M long hoses and 1 no.
Branch pipe with nozzle . The cabinet shall be painted with one coat of primer and
2 or more coats of synthetic enamel paint of approved make & shade and shall be
suitably mounted on a raised masonry platform complete as reqd.(Make:self
Fabricated)
each
each
each
Rs.4,855.07
Rs.9,124.18
Rs.2,456.70
each
each
Rs.7,979.21
Rs.13,186.36
each
each
each
Rs.8,772.05
Rs.14,138.93
Rs.4,681.95
a) 900X600X450
29.1.5
29.1.6
29.1.7
29.1.8
b) 2000 X 1200 X450

Providing & Fixing of Gun Metal 63 mm dia Short Branch Pipe with 20 mm dia
nozzle, ISI marked (IS:903) complete as required.
(Make: ESSEL/WINCO/NEWAGE).
Providing & Fixing of Gun Metal fire Brigade Connection (inlet collection head)
consisting of 63mm instantaneous type male coupling with built in check valves and
150 mm dia flanged outlet complete with bolts, nuts and rubber insertions as per
IS:904-1983 complete as reqd.
MAKE: ESSEL/WINCO/NEWAGE
a) 02 way
b) 04 way
Providing & fixing of Gun Metal fire Brigade connection (withdrawl connecting
head) consisting of 63mm instantaneous type male coupling with built in check
valves and 150mm dia flanged outlet complete with bolts, nuts and rubber
insertions as per IS:904-1983 complete as reqd.
MAKE: ESSEL/WINCO/NEWAGE
a) 2 way
b) 4 way
Providing & Fixing of Weather Proof M.S. Cabinet (to enclose above Inlet Collection
Head Connection) fabricated from 16 S.W.G. M.S. sheet centre opening with 3 mm
thick full front glass door and locking arrangement duly painted with one coat of
primer and two or more coasts of synthetic enamel paint of appreoved make and
shade and suitably mounted. Exact size and shape shall be subject to site conditions
and prior approval.
(Make:Self Fabricated)
Ch-29 : Fire Fighting works
Page-151
Item
No.
29.1.9
Description
Unit
Providing & fixing of Gun Metal fire Brigade suction hose coupling (draw out
connection) with nut for female coupling as per IS:902-1974 complete with 150
mm dia GI suction pipe and foot valve (to be connected to static Tank) complete as
reqd.(Make: Self Fabricated)
each
Rs.49,568.63
29.1.10 Providing & fixing of Weather Proof M.S. cabinet (to enclose above draw out
connection) fabricated from 16SWG M.S. sheet centre opening with 3mm thick full
front glass door and locking arrangement duly painted with one coat of primer and
two or more coats of synthetic enamel paint of appreoved make and shade and
sutable mounted . Exact size and shape shall be subject to site conditions and prior
approval) (Make: Self Fabricated)
29.1.11 Providing ,Fixing ,Testing & Commissioning of air Release Valve
each
Rs.4,834.42
a) 25 mm dia
b) 50 mm dia
29.1.12 Providing,Fixing,Testing & Commissioning of Mild Steel Black Pipe(IS:1239part-I)
Heavy class including cutting, screwing, welding etc. and providing all fittings viz
forged steel screwed fitting upto 50mm dia and bolt welded above 50mm dia
flanges, bends, tees, reducers, elbow, clamps, hangers etc including cutting holes
and chases in brick or RCC walls/ slabs and making good the same to the approval
of Engineer-in-charge/ consultant complete including painting with one coat of
primer and two or more coats of synthetic enamel paint of approved make and
shade including steel work complete as required.
(Make:TATA/JINDAL/NEZONE)
a) 200 mm dia
each
each
Rs.3,905.85
Rs.6,589.29
rm
Rs.2,719.77
b) 150 mm dia
rm
Rs.2,109.90
c) 100 mm dia
rm
Rs.1,597.60
d) 80 mm dia
e) 65 mm dia
rm
Rs.1,201.03
rm
Rs.985.00
f) 50 mm dia
rm
Rs.834.58
g) 40 mm dia
rm
Rs.772.95
h) 32 mm dia
rm
Rs.664.30
i) 25 mm dia
j) 20 mm dia
rm
Rs.555.71
rm
Rs.452.03
rm
Rs.372.75
a) 200 mm dia
rm
Rs.2,940.40
b) 150 mm dia
c) 100 mm dia
rm
Rs.2,330.53
rm
Rs.1,604.78
d) 80 mm dia
rm
Rs.1,409.62
rm
Rs.1,263.25
rm
Rs.897.33
k) 15 mm dia
29.1.13 Providing,Fixing,Testing & Commissioning of Mild Steel Black Pipe(IS:1239part-I)
Heavy class including cutting, screwing, welding etc.complete with all fittings (butt
welded) viz flanges, bends, tees, elbows, reducers etc including excavation (upto
1.5 m Deep), back filling and removal of surplus soil & providing anti corrosive
treatment(coating and wrapping) as per IS:10221 with 4 mm thick tape complete as
reqd.
(MAKE:TATA/JINDAL/NEZONE)
e) 65 mm dia
f) 40 mm dia
29.1.14 Supplying & Fixing Cast iron body Non Return valves complete with matching
flanges, rubber insertion, nuts, bolts and washer etc. (IS:5312) of following sizes
complete as reqd.
(Make:Koley/Kalpana/Audco)
Rate
Page-152
Item
No.
Description
(a)
150 mm dia
(b)
100 mm dia
(c)
80 mm dia
29.1.15 Supplying & Fixing,cast iron body Butterfly Valves with matching flanges, rubber
insertion, nuts, bolts and washer etc (IS:13095) of following size complete as reqd.
(MAKE:KOLEY/KALPANA/AUDCO)
Unit
Rate
each
each
each
Rs.22,000.07
Rs.18,397.44
Rs.12,485.15
(a) 200 mm dia

(b) 150 mm dia
each
Rs.18,584.24
each
Rs.17,429.39
(c) 100 mm dia
each
Rs.8,879.44
(d) 80 mm dia
each
Rs.6,543.40
(e) 65 mm dia
each
Rs.5,276.51
(f) 50 mm dia
(g) 40 mm dia
each
Rs.4,768.13
each
Rs.3,330.84
each
each
Rs.3,712.13
Rs.2,191.67
29.1.16 Providing ,Fixing,Testing & Commissioning of G.M. Stop Valve ISI Marked screwed
type tested to 30Kg/cm2 pressure as per IS:778-1984 of following sizes complete as
reqd.
(a) 50 mm dia
(b) 25 mm dia
29.1.17 Providing, Erection, Testing & Commissioning of Cast Iron Sluice Valve/ Gate Valve
confirming to IS:14846/2000 complete with
matching flanges, rubber insertion, nuts, bolts and washer etc of following size
complete as required
(MAKE:KOLEY/KALPANA/AUDCO)
(a)
200 mm dia
each
Rs.15,811.38
(b)
150 mm dia
each
Rs.12,113.04
(c)
100 mm dia
each
Rs.9,100.38
(d) 80 mm dia
29.1.18 Providing, erection testing, Commissioning of Cast Iron Foot Valve/Stainer
confirming to IS:4038/1538 complete with flanges, nuts, bolts and washer etc as
required
(a) 200 mm dia
each
Rs.6,903.65
each
Rs.24,414.72
(b) 150 mm dia

29.1.19 Providing,erection testing & commissioning of pressure gauge 100 mm dia (010Kg/cm2)
29.1.20 Providing ,erection,Testing & Commissioning of Pressure Switch
(MAKE:INDFOSS)
each
Rs.14,498.06
each
Rs.1,757.03
each
Rs.3,796.85
29.1.21 Supplying, Installation,Testing & Commissioning of 15 mm dia quartzoid Bulb Type

G.M. Sprinkler Head sutable to operate at 68* C complete as reqd.(UL/FM/LPC
listed/Approved)
(Make : HD Fire / TYCO)
each
Rs.508.41
29.1.22 Supply,installation,testing & commissioning of 150 mm dia installation control

valve assembly comprising of vertical wet alarm valve, hydraulic alarm motor &
gong, 15 mm dia Test Valve, 50 mm dia , Drain Valve and all necessary trimming
connections including 02 nos. pressure gauge as per manufacturers catalogue
complete as reqd.(UL/FM/LPC Listed/Approved)
(Make : HD FIRE )
each
Rs.99,356.82
Page-153
Item
Description
No.
29.1.23 Supplying and laying of following size NP2 class RCC Hume pipe i/c collars jointed
with stiff mixture of cement morter 1:2 ( 1 cement:2 fine sand) across the road
including cutting the road ( if reqd) digging the trench, refilling the same after
laying pipe, ramming the soil etc as reqd.
(a) 400 mm dia
(b) 300 mm dia
29.1.24 Supplying, Installation, Testing & Commissioning of First Aid Hose reel drawn with
30 Mtrs. Long rubber hose and G.M shut off nozzle, 25mm dia Gate valve, Union
pipe complete set confirming to IS: 884.
29.2
29.2.1
29.2.2
FIRE EXTINGUISHER
Supply, Installation, Fixing of DRY CHEMICAL POWDER Fire Extinguisher confirming
to IS: 2171 with ISI mark and CO2 cartridge will be confirming to IS: 4947 with ISI
mark, Powder will be confirming to IS: 4308 with ISI Mark (5 KG)
BRAND : FIRESTOP / FIREND / FIRE SHIELD
mark, Powder will be confirming to IS: 4308 with ISI Mark (10 kg)
Unit
Rate
rm
rm
each
Rs.2,447.96
Rs.1,960.06
Rs.13,206.57
each
Rs.3,543.00
each
Rs.4,684.34
29.2.3

to IS: 2171 with ISI Mark, and CO2 Cylinder will be confirming to IS: 4947 with ISI
Mark, Powder will be confirming to IS: 2878 with ISI Mark (Extinguisher will be
TROLLEY MOUNTED)(25 KG)
each
Rs.22,754.01
29.2.4

mark, Powder will be confirming to IS: 4308 with ISI Mark (Extinguisher will be
TROLLEY MOUNTED).(50 KG)
each
Rs.32,755.93
29.2.5

mark, Powder will be confirming to IS: 4308 with ISI Mark (Extinguisher will be
TROLLEY MOUNTED)(75 KG)
each
Rs.37,646.53
29.2.6
Supply, Installation, Fixing of MECHANICAL FOAM (AFFF) Fire Extinguisher

confirming to IS: 10204 with ISI Mark and CO2 Cartridge will be confirming to IS:
4947 with ISI mark, (AFFF) will be confirming to IS: 4989 with ISI Mark.(9 LTRS)
each
Rs.3,116.09
29.2.7
Supply, Installation, Fixing of MECHANICAL FOAM (AFFF) Fire Extinguisher

confirming to IS: 10204 with ISI Mark and CO2 Cartridge will be confirming to IS:
4947 with ISI mark, (AFFF) will be confirming to IS: 4989 with ISI Mark.(50 LITERS)
Supply, Installation, Fixing of WATER CO2 Fire Extinguisher confirming to IS: 940
with ISI Mark and CO2 Cartridge will be confirming to IS: 4947 with ISI Mark.(09
LITERS)
BRAND: FIRESTOP / FIREND / FIRESHIELD
each
Rs.19,344.23
each
Rs.2,628.19
Supply, Installation, Fixing of CARBON DIOXIDE Fire Extinguisher confirming to IS:

2878 with ISI Mark.(4.5 LITERS)
BRAND: FIRESTOP / FIREND / FIRESHIELD
each
Rs.9,849.09
29.2.8
29.2.9
Page-154
Item
Description
No.
29.2.10 Supply, Installation, Fixing of CARBON DIOXIDE Fire Extinguisher confirming to IS:
2878 with ISI Mark. (Extinguisher will be TROLLEY MOUNTED)(6.5 KG)
Unit
Rate
each
Rs.11,257.90
2878 with ISI Mark. (Extinguisher will be TROLLEY MOUNTED)(9 KG)
each
Rs.15,651.42
2878 with ISI Mark, (Extinguisher will be TROLLEY MOUNTED)(2KG)
29.2.13 Supply, Installation, Fixing of ABC Stored Pressure Fire Extinguisher with built In
pressure Gauge to know the Ready ness of the Extinguisher Squeeze Grip Handle As
per IS:13849 with ISI mark
(05 kg capacity)
each
Rs.6,578.99
each
Rs.5,556.46
29.2.14 Supply, Installation, Fixing of ABC stored Pressure Fire Extinguisher with built In
Pressure Gauge to know the Ready ness of the Extinguisher Squeeze Grip Handle as
per IS:13849 with ISI mark.
(10 kg capacity)
29.3 FIRE EXTINGUISHER REFILLING & SERVICING
each
Rs.11,716.18
29.3.1 Refilling & Servicing of DCP Type 05 Kg Capacity Fire Extinguisher with ISI Mark refill
etc. complete
each
Rs.1,450.00
29.3.2 Refilling & Servicing of DCP Type 10 Kg Capacity Fire Extinguisher with ISI Mark refill
etc. complete
each
Rs.2,275.00
29.3.3 Refilling & Servicing of Water CO2 Type 09 Ltrs Capacity Fire Extinguisher with ISI
Mark refill etc. complete
each
Rs.480.00
29.3.4 Refilling & Servicing of Mechanical Foam AFFF Type 09 Ltrs Capacity Fire
Extinguisher with ISI Mark refill etc. complete
each
Rs.525.00
29.3.5 Refilling & Servicing of ABC Type 05 Kg Capacity Fire Extinguisher with ISI Mark refill
etc. complete
each
Rs.1,670.00
29.3.6 Refilling & Servicing of CO2 Type Fire Extinguisher with ISI Mark refill etc. complete
(a)
(b)
(c)
(d)
02 Kg
4.5 Kg
6.5 Kg
09 Kg
each
each
each
each
Rs
Rs
Rs
Rs
720.00
1,650.00
2,325.00
3,630.00
Page-155
CHAPTER 30. R.C.C APPROACH ROAD

Item
Item
No.
30.1 Construction of Sub-grade and earthen shoulders with approved materials obtained
from borrow pits, with all lifts & leads, transporting to site, spreading, grading to
required slope and compacting to meet requirement of table 300-2 (including
compensation of earth ). (Including cost of testing of materials at site and
laboratory as directed by the deptt.)
Unit
Rate
a) from Private land
cum
Rs.235.00
b) from Government land
cum
Rs.235.00
c) Extra lead beyond initial lead of 3.00km

30.2 Construction of Granular sub-base by providing close graded material, spreading in
uniform layers with motor grader on prepared surface, mixing by mix in place
method with rotavator at OMC, and compacting with vibratory roller to achieve the
desired density, complete as per Clause 401 of MoRTH specifications (with an initial
lead of 5 km) (including cost of testing of materials at site and laboratory as
directed by the deptt.)
(a)Using Grading I material
cum/km
Rs.8.46
cum
Rs.2,040.00
(b)Using Grading II material
cum
Rs.2,094.00
(c)Using Grading III material
cum
Rs.1,965.00
(d) Extra lead beyond initial lead of 5.00km
cum/km
Rs.8.46
30.3 Supplying, fitting and fixing in position reinforcement bars conforming to relevant
I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and
bending to proper shapes and length as per details, supplying and binding with 20G
annealed black wire and placing in position with proper blocks, supports, chairs,
spacers etc. complete
a) TMT Bar
(i) From Primary Producer
qntl
Rs.6,902.86
(ii) Other ISI Marked approved brand
qntl
Rs.6,026.82
b) ISI approved - M.S. Rod
qntl
Rs.6,767.66
sqm
Rs.276.07
sqm
Rs.252.24
(a) M 20 Grade Concrete
cu.m.
Rs.7,218.26
(b) M 25 Grade Concrete
cum
Rs.7,798.14
(c) M 30Grade Concrete
cum
Rs.7,848.98
30.4 Providing form work of ordinary timber planking so as to give a rough finish
including centering, shuttering, strutting and propping etc., and removal of the
same for in-situ reinforced concrete and plain concrete work in R.C.C. approach
road.
30.5 Providing and laying controlled cement concrete pavement of approved grade with
20mm down graded stone aggregate over a prepared sub-base including
dewatering if necessary, spread, compacted and finished in a continuous operation
including provision of construction and expansion joints, plasticiser and curing
compound of Fosroc/ Sika/ Choksey/ Degusa and hardener of Recron/ Degusa/
Fosroc; finishing to lines and grades and curing as specified and directed complete
(form work and reinforcement shall be measured and paid separately).
Ch-30 : RCC Approach Road
Page-156
Item
Item
No.
30.6 15 mm thick Cement plaster in single coat with hardener of Recron/ Degusa/ Fosroc
on brick/concrete for plastering including arises, internal rounded
angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished
even and smooth including curing complete as directed.
Unit
Rate
(a) In cement mortar 1:3
sqm
Rs.166.34
(b) In cement mortar 1:4
sqm
Rs.146.60
sqm
Rs.937.68
30.7 Providing and laying of inter locking concrete block pavement (ICBP) with cement
concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days
compressive strength not less than 30 N/m over a layer of bedding sand of
compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern
of bonds as directed by the engineer and in proper level and grade and compacted
with appropriate equipment such as plat vibrator along with spreading of a thin
layer of joint filling sand to fill up the gaps between blocks including construction of
edge restraint wherever required complete as per drawings and Technical
specification clause 1504 of MORD.
Ch-30 : RCC Approach Road
Page-157
CH-31: ACOUSTIC TREATMENT

Description
Item
No.
Unit
Rate
a) 20 MM
Sqm
Rs.4,853.79
b) 25 MM
Sqm
Rs.5,149.86
c) Armstrong OPTRA high acoustical wall panelling with fibre glass substrate 25
MM thick
Sqm
Rs.9,060.37
d) Armstrong Wood works acoustical wall panelling
Sqm
Rs.9,931.33
a) 20 MM
Sqm
Rs.5,900.41
b) 25 MM
Sqm
Rs.6,156.16
a) 20 MM
Sqm
Rs.2,931.57
b) 25 MM
Sqm
Rs.3,298.50
c) 25 MM
Sqm
Rs.3,528.30
a) 20 MM
Sqm
Rs.3,168.78
b) 25 MM
Sqm
Rs.3,533.86
c) 25 MM
Sqm
Rs.3,728.04
a) 20 MM
Sqm
Rs.3,428.23
b) 25 MM
Sqm
Rs.3,682.12
a) 20 MM
Sqm
Rs.3,665.44
b) 25 MM
Sqm
Rs.3,919.33
a) 20 MM
Sqm
Rs.3,763.66
b) 25 MM
Sqm
Rs.4,130.60
31.1 Supplying, fitting and fixing SoundSoak NSS Cord (FSS Cord) wrapped acoustical
wall panel system of Anutone Acoustics Ltd. Including all fixtures and fittings.
31.2 Supplying, fitting and fixing SoundSoak FSS Cordura wrapped acoustical wall panel
system of Anutone Acoustics Ltd. Including all fixtures and fittings.
31.3 Supplying, fitting and fixing SoundSmooth MB Primer (NSS Primer) with glass wool
of Anutone Acoustics Ltd. Including all fixtures and fittings.
31.4 Supplying, fitting and fixing SoundSmooth MB White (NSS White) with glass wool
of Anutone Acoustics Ltd. Including all fixtures and fittings.
31.5 Supplying, fitting and fixing SoundSmooth MB Trax (NSS Trax) with glass wool of
Anutone Acoustics Ltd. Including all fixtures and fittings.
31.6 Supplying, fitting and fixing SoundSmooth MB Trax White (NSS Trax) with glass
wool of Anutone Acoustics Ltd. Including all fixtures and fittings.
31.7 Supplying, fitting and fixing Mat White (Mat White) with glass wool of Anutone
Acoustics Ltd. Including all fixtures and fittings.
31.8 Supplying, fitting and fixing Mat White Trax (Mat White) with glass wool of
a) 20 MM
Rs.4,173.22
31.9 Supplying, fitting and fixing Sound Sonator with glass wool of Anutone Acoustics
Ltd. Including all fixtures and fittings.
a) 15 MM
Ch-31 : Acoustic Treatment
Sqm
Rs.3,644.44
Page-158
Description
Item
No.
Unit
Rate
a) 15 MM
Sqm
Rs.3,544.56
b) 20 MM
Sqm
Rs.3,922.62
a) 15 MM
Sqm
Rs.3,114.62
b) 20 MM
Sqm
Rs.3,689.53
c) 25 MM
Sqm
Rs.3,919.33
a) 18mm 900 kg/ M2
Sqm
Rs.2,794.01
b) 18mm 1200 kg/ M2
Sqm
Rs.3,008.86
a) 15mm Square
Sqm
Rs.2,137.31
b) 15mm Steppe
Sqm
Rs.2,292.98
a) 15mm Square
Sqm
Rs.2,149.25
b) 15mm Steppe
Sqm
Rs.2,299.36
Sqm
Rs.5,293.39
Sqm
Rs.10,507.32
Sqm
Rs.11,032.00
a) 16 MM PITCH
Sqm
Rs.20,133.05
b) 32 MM PITCH
Sqm
Rs.17,571.91
c) 16 MM PITCH FR
Sqm
Rs.25,461.03
d) 32 MM PITCH FR
Sqm
Rs.22,899.89
Acoustical suspended ceiling system

with armstrong 24mm exposed grid
Sqm
Rs.1,785.67
Acoustical suspended ceiling system

with armstrong 24mm exposed grid
Sqm
Rs.1,866.32
31.10 Supplying, fitting and fixing Mat Black (Mat Black) with glass wool of Anutone
31.11 Supplying, fitting and fixing SoundSmooth Ebony (NSS Ebony) with glass wool of
31.12 Supplying, fitting and fixing Mat BSB with glass wool of Anutone Acoustics Ltd.
Including all fixtures and fittings.
31.13 Supplying, fitting and fixing SubTex Nubby/Pebble- TEXTURE CEILING of Anutone
31.13.1 SubTex
31.13.2 SubTex Ebony
31.13.3 FABSTRETCH 25 mm with 50 mm Air Gap

a) 25mm
31.13.4 ACT GLD INSTALLED USING IMPALLING CLIPS
a) 25mm
31.13.5 ACT GLD INSTALLED USING Z Bar
a) 25mm
31.13.6 SOUNDSLATS
31.14 Armstrong acoustical ceilng

31.14.1 Providing & fixing Armstrong Mineral fibre
with beauty sky ( board/tegular) edge tiles
(600x600x14)mm
31.14.2 Providing & fixing Armstrong Mineral fibre
with beauty sky ( board/tegular) edge tiles
(600x600x15)mm
Page-159
Item
No.
Description
Unit
Rate
31.14.3 Providing & fixing Armstrong Mineral fibre Acoustical suspended ceiling system
with optra FG ( board/tegular) edge tiles with armstrong XL 24mm exposed grid
(600x600x15)mm
Sqm
Rs.3,801.93
with dune ( bev. tegular) edge tiles with armstrong XL 15mm exposed / silhouette
grid (600x600x16)mm
Sqm
Rs.2,511.53
with dune ( board/ tegular) edge tiles with armstrong XL 24mm exposed grid
(600x600x16)mm
Sqm
Rs.2,350.23
with fine fissured / classic lite ( bev. tegular) edge tiles with armstrong XL 15mm
exposed / silhouette grid (600x600x16)mm
Sqm
Rs.2,188.92
with fine fittured / classic lite ( board/ tegular) edge tiles with armstrong 24mm
exposed grid (600x600x16)mm
Sqm
Rs.2,108.27
with ANF ( bev. tegular) edge tiles with armstrong XL 15mm exposed / silhouette
grid (600x600x16)mm
Sqm
Rs.1,946.97
Page-160
CH-32 : COMPOSITE ITEMS OF WORKS

Item No.
Description
Unit
Rate
32.1
32.1.1
RCC Work with Shuttering

Providing and laying plain/reinforced cement croncrete works using cement,
coarse sand & 20mm down graded stone aggregate with cost of necessary form
work including dewatering if necessary, and curing for reinforced cement concrete
work complete as directed (Reinforcement will be measured and paid separately)
Cum
Cum
Cum
Rs. 6,683.67
Rs. 7,250.67
Rs. 8,281.89
Cum
Cum
Cum
Rs. 6,904.19
Rs. 7,516.50
Rs. 8,590.77
Cum
Cum
Cum
Rs. 7,624.89
Rs. 8,197.46
Rs. 8,742.08
Cum
Cum
Cum
Rs. 7,845.41
Rs. 8,463.29
Rs. 9,050.96
Cum
Cum
Cum
Rs. 7,422.09
Rs. 7,994.66
Rs. 8,539.28
Cum
Cum
Cum
Rs. 7,642.61
Rs. 8,260.49
Rs. 8,848.16

(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(c) M25 grade concrete
Cum
Cum
Cum
Rs. 8,247.72
Rs. 8,820.29
Rs. 9,364.91
(a) M15 or Prop. 1:2:4

(b) M20 or Prop. 1:11/2:3
Cum
Cum
Rs. 8,468.24
Rs. 9,086.12
I) Using mixture machine

(A) In sub - structure up to plinth level
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
B) In super structure up to 1st floor level
i) Vertical members like column, pillars, post, struts etc
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
ii) Horizontal members like beam, lintel, girder bressumer etc.
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
iii) Suspended floor (Slab, balcony, staircase etc)
Ch-32 : Composite Items of Work
Page-161
Item No.
Description
Unit
Rate

iv) Walls (thickness not less than 100mm) including attached pillasters,
buttresses, plinth and string course etc.
Cum
Rs. 9,673.79
Cum
Cum
Cum
Rs. 7,474.02
Rs. 8,046.59
Rs. 8,591.20
Cum
Cum
Cum
Rs. 7,694.54
Rs. 8,312.42
Rs. 8,900.08
Cum
Cum
Cum
Rs. 12,566.67
Rs. 13,139.19
Rs. 13,683.84
Cum
Cum
Cum
Rs. 12,787.19
Rs. 13,405.02
Rs. 13,992.72
Cum
Cum
Cum
Rs. 9,785.54
Rs. 10,363.66
Rs. 10,913.58
Cum
Cum
Cum
Rs. 10,006.06
Rs. 10,629.49
Rs. 11,222.46

(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
Cum
Cum
Cum
Rs. 6,999.98
Rs. 7,550.42
Rs. 8,073.99
(a) M15 or Prop. 1:2:4
Cum
Rs. 7,220.50
(b) M20 or Prop. 1:11/2:3
Cum
Rs. 7,816.25
Cum
Rs. 8,382.87

(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
v) Vertical and horizontal fins (thickness not more than 100mm) individually or
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
vi) On domes, vaults and shell roof
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(II) Using Batching Plant/ RMC/ Truck mounted batching plant including Transit
Mixer and Concrete Pump
(A) In sub - structure up to plinth level
(B) Super-structure from plinth level upto 1st floor level.

i) Vertcal members (Column, pillars, post, struts etc)
Page-162
Item No.
Description
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
ii) Horizontal members (Beam, lintel, girder etc.)
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
iii) Suspended floor (Slab, balcony, staircase etc)
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
iv) Walls (thickness not less than 100mm) including attached pillasters,
buttresses, plinth and string course etc.
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
v) Vertical and horizontal fins (thickness not more than 100mm) individually or
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
(a) M15 or Prop. 1:2:4
(b) M20 or Prop. 1:11/2:3
v) On domes, vaults and shell roof
(a) M15 or Prop. 1:2:4
Unit
Rate
Cum
Cum
Cum
Rs. 7,899.48
Rs. 8,495.23
Rs. 9,061.86
Cum
Cum
Cum
Rs. 8,120.00
Rs. 8,761.06
Rs. 9,370.74
Cum
Cum
Cum
Rs. 7,696.68
Rs. 8,292.43
Rs. 8,859.06
Cum
Cum
Cum
Rs. 7,917.20
Rs. 8,558.26
Rs. 9,167.94
Cum
Cum
Cum
Rs. 8,522.31
Rs. 9,118.06
Rs. 9,684.69
Cum
Cum
Cum
Rs. 8,742.83
Rs. 9,383.89
Rs. 9,993.57
Cum
Cum
Cum
Rs. 7,838.68
Rs. 8,434.43
Rs. 9,001.06
Cum
Cum
Cum
Rs. 8,059.20
Rs. 8,700.26
Rs. 9,309.94
Cum
Cum
Cum
Rs. 12,398.08
Rs. 12,993.84
Rs. 13,560.45
Cum
Cum
Cum
Rs. 12,618.60
Rs. 13,259.67
Rs. 13,869.33
Cum
Rs. 9,490.18
Page-163
Item No.
32.1.2
32.2
32.2.1
Description
Unit
Rate
(b) M20 or Prop. 1:11/2:3

Cum
Cum
Rs. 10,085.93
Rs. 10,652.56
(a) M15 or Prop. 1:2:4

(b) M20 or Prop. 1:11/2:3
Extra for every subsequent floor above 1st floor on item no 32.1.(I)
Cum
Cum
Cum
Cum
Rs. 9,710.70
Rs. 10,351.76
Rs. 10,961.44
Rs. 306.19
a) Brick work in cement morter proportion 1:5
Cum
Rs. 6,138.40
b) Brick work in cement morter proportion 1:6
Cum
Rs. 6,023.15
Cum
Rs. 6,099.36
Cum
Rs. 5,984.11
Cum
Rs. 6,073.32
Cum
Rs. 5,958.07
Cum
Rs. 6,263.84
Cum
Rs. 6,148.59
Cum
Rs. 6,217.71
Cum
Rs. 6,102.46
Cum
Rs. 6,179.66
Cum
Rs. 6,064.41
Cum
Rs. 6,575.84
Cum
Rs. 6,460.59
Cum
Rs. 6,513.71
Cum
Rs. 6,398.46
Cum
Rs. 6,461.62
Brickwork with Plastering

Brick work in cement morter with 1st class brick including cement mortar
plastering, racking out joints and dewatering if necessary, and curing complete as
directed in sub-structure up to plinth level.
(I) One side plastering with 10mm thick
i) Using plastering of cement mortar prop. 1:4
ii) Using plastering of cement mortar prop. 1:5
iii) Using plastering of cement mortar prop. 1:6
(II) One side plastering with 15mm thick

(III) One side plastering with 20mm thick


Page-164
Item No.
Description
Unit
Rate
Cum
Rs. 6,346.37
Cum
Rs. 6,304.91
Cum
Rs. 6,189.65
Cum
Rs. 6,265.87
Cum
Rs. 6,150.61
Cum
Rs. 6,239.83
Cum
Rs. 6,124.57
Cum
Rs. 6,430.35
Cum
Rs. 6,315.09
Cum
Rs. 6,384.22
Cum
Rs. 6,268.96
Cum
Rs. 6,346.17
Cum
Rs. 6,230.91
Cum
Rs. 6,945.04
Cum
Rs. 6,829.78
Cum
Rs. 6,859.91
Cum
Rs. 6,744.65
Cum
Rs. 6,795.79
Cum
Rs. 6,680.53
Cum
Rs. 7,070.48

32.2.2
Brick work in cement mortar with 1st class brick including cement motar
plastering, racking out joints and curing complete as directed in superstructure
above plinth level up to 1st floor level.
A) One side plastering
I) 10mm thick plastering
i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6
II) 15mm thick plastering

i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6
B) Both side plastering

I) With fair side 10mm thick and rough side 15mm thick plastering
i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6
II) With both side 15mm thick plastering

i) In prop. 1:4
Page-165
Item No.
Description
Unit
Rate
Cum
Rs. 6,955.22
Cum
Rs. 6,978.26
Cum
Rs. 6,863.00
Cum
Rs. 6,902.13
Cum
Rs. 6,786.87
Extra over item no. 32.2.2 above for brick work in each subsequent floor or part
Brick work in cement morter with 1st class brick including cement mortar
plastering, racking out joints and dewatering if necessary, and curing complete as
directed in sub-structure up to plinth level.
Cum
Rs. 293.57
Cum
Rs. 1,411.69
Cum
Rs. 1,384.95
Cum
Rs. 1,402.71
Cum
Rs. 1,375.97
Cum
Rs. 1,396.72
Cum
Rs. 1,369.98
Cum
Rs. 1,440.54
Cum
Rs. 1,413.80
Cum
Rs. 1,429.93
Cum
Rs. 1,403.19
Cum
Rs. 1,421.18
Cum
Rs. 1,394.44
Cum
Rs. 1,512.30
Cum
Rs. 1,485.56
Cum
Rs. 1,498.01
Cum
Rs. 1,471.27

ii) In prop. 1:5
iii) In prop. 1:6
32.2.3
32.2.4
I) One side plastering with 10mm thick

II) One side plastering with 15mm thick

III) One side plastering with 20mm thick

Page-166
Item No.
32.2.5
Description
Unit
Rate
Cum
Rs. 1,486.03
Cum
Rs. 1,459.29
Cum
Rs. 1,450.16
Cum
Rs. 1,423.43
Cum
Rs. 1,441.18
Cum
Rs. 1,414.45
Cum
Rs. 1,435.19
Cum
Rs. 1,408.46
Cum
Rs. 1,479.01
Cum
Rs. 1,452.28
Cum
Rs. 1,468.40
Cum
Rs. 1,441.67
Cum
Rs. 1,459.65
Cum
Rs. 1,432.92
Cum
Rs. 1,597.39
Cum
Rs. 1,570.66
Cum
Rs. 1,577.81
Cum
Rs. 1,551.08
Cum
Rs. 1,563.06
Cum
Rs. 1,536.33
Cum
Rs. 1,626.24
Brick work in cement mortar with 1st class brick including cement motar
plastering, racking out joints and curing complete as directed in superstructure
above plinth level up to 1st floor level.
i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6

i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6

I) With fair side 10mm thick and rough side 15mm thick plastering
i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6
II) With both side 15mm thick plastering

i) In prop. 1:4
Page-167
Item No.
Description
Unit
Rate
Cum
Rs. 1,599.51
Cum
Rs. 1,605.03
Cum
Rs. 1,578.30
Cum
Rs. 1,587.52
Cum
Rs. 1,560.79
Extra over item no. 32.2.2 above for brick work in each subsequent floor or part
112mm thick 1st class brick nogged wall in cement mortar including racking out
joints and curing complete as directed in super structure above plinth up to 1st
floor level (protruding M.S rod/Tor steel of column to be embeded in cement
mortar and will be measured and paid separately)
Cum
Rs. 67.37
Sqm
Rs. 1,507.11
Sqm
Rs. 1,464.70
c) Brick work in cement morter proportion 1:6
Sqm
Rs. 1,411.69
Sqm
Rs. 1,498.13
Sqm
Rs. 1,455.72
Sqm
Rs. 1,402.71
Sqm
Rs. 1,492.14
Sqm
Rs. 1,449.73
Sqm
Rs. 1,396.72
Sqm
Rs. 1,537.49
Sqm
Rs. 1,495.08
Sqm
Rs. 1,442.07
Sqm
Rs. 1,526.89
Sqm
Rs. 1,484.48
Sqm
Rs. 1,431.47
Sqm
Rs. 1,518.13
Sqm
Rs. 1,475.72
Sqm
Rs. 1,422.71

ii) In prop. 1:5
iii) In prop. 1:6
32.2.6
32.2.7

i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6

i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6
Page-168
Item No.
Description
Unit
Rate

I) With fair side 10mm thick and rough side 15mm thickplastering
i) In prop. 1:4
Sqm
Rs. 1,654.34
Sqm
Rs. 1,611.93
Sqm
Rs. 1,558.92
Sqm
Rs. 1,634.76
Sqm
Rs. 1,592.35
Sqm
Rs. 1,539.34
Sqm
Rs. 1,620.01
Sqm
Rs. 1,577.60
Sqm
Rs. 1,524.59
Sqm
Rs. 1,683.19
Sqm
Rs. 1,640.78
Sqm
Rs. 1,587.77
Sqm
Rs. 1,661.98
Sqm
Rs. 1,619.57
Sqm
Rs. 1,566.56
Sqm
Rs. 1,644.47
Sqm
Rs. 1,602.06
Sqm
Rs. 1,549.05
Extra over item no 32.2.4 for brick walling including plastering for each subsequent
floor or part thereof above the 1st floor level.
Sqm
Rs. 459.28
Sqm
Rs. 764.05
ii) In prop. 1:5
iii) In prop. 1:6
II) Both side 15mm thick plastering

i) In prop. 1:4
ii) In prop. 1:5
iii) In prop. 1:6
32.2.8
32.3
CEMENT CONCRETE FLOORING WITH BRICK SOLING
32.3.1
40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in

prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 12.5 mm and down) and 15 mm
thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse
aggregate of size 10mm down) finished with a floating coat of neat cement finish using
cement slurry for bond @ 2.75 kg. per square metre of floor area , wearing layer is to be laid
in panels including brick on flat soling, curing etc. complete as directed.
Page-169
Item No.
Description
Unit
Rate
32.3.2
65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in

prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm
thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse
aggregate of size 10mm down) laid in panels and finished with a floating coat of neat cement
finish (using cement slurry for bond @ 2.75 kg. per square metre of floor area) including
brick on flat soling,curing etc. complete as directed.
Sqm
Rs. 869.62
32.3.3
40 mm thick red oxide floor with under layer of 30 mm thick cement concrete in prop. 1:3:6
(1cement : 3 coarse sand : 6 coarse aggregate of size 20 mm and down) and top layer of
10mm thick plaster of cement red-oxide of iron per 50 kg of cement in prop. 1:3 (1 cement
red oxide: 3 coarse sand) finished with a floating coat of neat cement red oxide mix of same
proportion including brick on flat soling,
Sqm
Rs. 800.61
32.3.4
Providing and laying 50mm thick C.C. floor with metallic concrete hardener topping under
layer of 35 mm thick cement concrete in prop.1:2:4 (1cement : 2 coarse sand : 4 coarse
aggregate of 20 mm and down) and top layer of 15mm thick of metallic cement hardener
consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate 6 mm and down) by
volume with which metallic hardening compound of approved quality is mixed in the ratio of
4:1 (4 parts of cement : 1 part of metallic floor hardening compound of approved quality by
weight) including finishing brick on flat soling with curing complete as directed. (For
Laboratory & Workshop Floor)
Sqm
Rs. 868.81
32.3.5
Providing and laying 65mm thick C.C. floor with metallic concrete hardener topping under
layer of 50 mm thick cement concrete 1:2:4 (1cement:2 coarse sand:4 coarse aggregate of 20
mm and down) and top layer of 15mm thick of metallic cement hardener consisting of mix
1:2 (1 cement hardener mix : 2 stone aggregate 6 mm and down) by volume with which
metallic hardening compound of approved quality is mixed in the ratio of 4:1 (4 parts of
cement: 1 part of metallic floor hardening compound of approved quality by weight)
including brick on flat soling, finishing with curing complete as directed. (For Laboratory &
Workshop Floor)
Sqm
Rs. 979.99
32.4
32.4.1
DOORS / WINDOWS WITH ALL FITTINGS

Providing fitting and fixing 1/3 panelled 2/3 glazed wooden shutters for
doors/windows including oxidised iron butt hinges (3nos X100mm x75 mm x3.55
mm), 300x10 mm Tower bolts-2nos,150 mm Door handle-2nos, 300x16mmSliding Door bolts-2nos and Door stopper with rubber stopper-1nos with necessay
screws all complete as directed
(i). 40 mm thick.
Sqm
Rs. 5,175.74
(ii). 35 mm thick.
Sqm
Rs. 4,875.51
(iii) 30 mm thick.
Sqm
Rs. 4,403.94

(Gamari/ Hollock/ Bonsum )
(i) 40 mm thick.
Sqm
Rs. 3,832.12
(ii) 35 mm thick.
Sqm
Rs. 3,666.05
(iii) 30 mm thick.
Sqm
Rs. 3,408.44
(i) 40 mm thick.
Sqm
Rs. 3,560.33
(ii). 35 mm thick.
Sqm
Rs. 3,420.07
(iii). 30 mm thick.
Sqm
Rs. 3,342.20
I) Using Electro Coloured Iron fittings

C).With 1st class local wood(Bola )
Page-170
Item No.
Description
Unit
Rate
(i) 40 mm thick.
Sqm
Rs. 5,330.38
(ii) 35 mm thick.
Sqm
Rs. 5,030.15
(iii) 30 mm thick.
Sqm
Rs. 4,558.58
(i) 40 mm thick.
Sqm
Rs. 3,986.76
(ii) 35 mm thick.
Sqm
Rs. 3,820.69
(iii) 30 mm thick.
Sqm
Rs. 3,563.08
(i) 40 mm thick.
Sqm
Rs. 3,714.97
(ii) 35 mm thick.
Sqm
Rs. 3,574.71
(iii) 30 mm thick.
Sqm
Rs. 3,347.02
(i). 40 mm thick.
Sqm
Rs. 5,868.63
(ii). 35 mm thick.
Sqm
Rs. 5,465.68
(iii) 30 mm thick.
Sqm
Rs. 4,460.18

(i) 40 mm thick.
Sqm
Rs. 4,158.63
(ii) 35 mm thick.
Sqm
Rs. 3,993.05
(iii) 30 mm thick.
Sqm
Rs. 3,374.73
(i) 40 mm thick.
Sqm
Rs. 4,107.39
(ii). 35 mm thick.
Sqm
Rs. 3,945.75
(iii). 30 mm thick.
Sqm
Rs. 3,342.20
(i) 40 mm thick.
Sqm
Rs. 6,023.27
(ii) 35 mm thick.
Sqm
Rs. 5,620.32
(iii) 30 mm thick.
Sqm
Rs. 4,614.82
(i) 40 mm thick.
Sqm
Rs. 4,313.27
(ii) 35 mm thick.
Sqm
Rs. 4,147.69
(iii) 30 mm thick.
Sqm
Rs. 3,529.37
II) Using Aluminium Fittings

B) With 1st class local wood (Gamari/ Hollock/ Bonsum )
32.4.2
Providing, fitting and fixing full panelled doors/ windows including oxidised M.S
butt hinges (100mm x75 mm x3.55mm), 300x10 mm Tower bolts-2nos,150 mm
Door handle-2nos, 300x16mm- Sliding Door bolts-2nos and Door stopper with
rubber stopper-1nos with necessay screws complete as directed
A).With Teak wood / Sissu wood.

B) With 1st class local wood (Gamari/ Hollock/ Bonsum )
Page-171
Item No.
Description
Unit
Rate
(i) 40 mm thick.
Sqm
Rs. 4,262.03
(ii) 35 mm thick.
Sqm
Rs. 4,100.39
(iii) 30 mm thick.
Sqm
Rs. 3,496.84
(i). 40 mm thick.
Sqm
Rs. 6,219.92
(ii). 35 mm thick.
Sqm
Rs. 5,435.26
(iii) 30 mm thick.
Sqm
Rs. 5,232.40

(i) 40 mm thick.
Sqm
Rs. 4,582.51
(ii) 35 mm thick.
Sqm
Rs. 4,146.06
(iii) 30 mm thick.
Sqm
Rs. 4,033.22
(i) 40 mm thick.
Sqm
Rs. 4,534.27
(ii). 35 mm thick.
Sqm
Rs. 4,108.08
(iii). 30 mm thick.
Sqm
Rs. 3,997.89
(i) 40 mm thick.
Sqm
Rs. 6,374.56
(ii) 35 mm thick.
Sqm
Rs. 5,589.90
(iii) 30 mm thick.
Sqm
Rs. 5,387.04
(i) 40 mm thick.
Sqm
Rs. 4,737.15
(ii) 35 mm thick.
Sqm
Rs. 4,300.70
(iii) 30 mm thick.
Sqm
Rs. 4,187.86
(i) 40 mm thick.
Sqm
Rs. 4,688.91
(ii) 35 mm thick.
Sqm
Rs. 4,262.72
(iii) 30 mm thick.
Sqm
Rs. 4,152.53
32.4.3
Providing, fitting and fixing factory made wooden panelled doors with panel
inserts of 75mm to 50mm width and 12mm to 20mm thickness,joined together
with continous tongue and groove joints glued together with Movicol or other
approved adhesive leaving a vertical groove of 7.5mm to 15mm between the
inserts,the edges of panel inserts being feather tongue into styles and rails
including providing three pairs of oxidised M.S butt hinges (100mm x75 mm
x3.55mm),300x12 mm Aluminium Tower bolts-2nos,150 mm Aluminium Door
handle-2nos, 300x16mm- Aluminium Sliding Door bolts-2nos and Door stopper
with rubber stopper-1nos with necessay screws and furnishing with moulded
timber beading of size 25mmx15mm around the panels complete as per drawing

A).With Teak wood / Sissu wood.
B) With 1st class local wood (Hollock/ Bonsum/ Gamari )
C) With 1st class local wood(Bola )
Page-172
Item No.
Description
Unit
Rate
32.4.4
Providing fitting and fixing 1st class local wood (Gamari/ Bonsum/ Hollock)
battened, framed and braced door and window shutters using 25mm thick planks
including oxidised iron butt hinges (100mm x58 mm x1.90 mm) 6 nos, 250x10 mm
Aluminium Tower bolts-2nos, 150 mm Aluminium Door handle-2no, 250x16mmAluminium Sliding Door bolts-1nos with necessay screws complete as directed
Sqm
Rs. 2,741.36
32.4.5
Providing, fitting and fixing fully glazed wooden door shutters with necessary butt
hinges, 250x10 mm Aluminium Tower bolts-2nos, 150 mm Aluminium Door handle2nos and Door stopper with rubber stopper-1nos with necessay screws etc.
complete as per approved drawing as directed and specified at all levels.( glass
panes should be measured and paid seperately.)
Sqm
Rs. 2,222.36
(A) With Gamari Wood.

(i) 40mm thick
(ii) 35mm thick
Rs. 2,139.59
(B)With 1st Class Local wood
32.4.6
(i) 40mm thick
Sqm
Rs. 2,040.91
(ii) 35mm thick
Sqm
Rs. 2,040.91
(i) 40mm thick
Sqm
Rs. 2,222.36
(ii) 35mm thick
Sqm
Rs. 2,139.59
(ii) 30mm thick
Sqm
Rs. 1,998.72
(i) 40mm thick
Sqm
Rs. 2,196.36
(ii) 35mm thick
Sqm
Rs. 2,116.80
(ii) 30mm thick
Sqm
Rs. 1,979.25
(i) 40mm thick
Sqm
Rs. 2,012.90
(ii) 35mm thick
Sqm
Rs. 1,956.47
(ii) 30mm thick
Sqm
Rs. 1,836.90
(i) 40mm thick
Sqm
Rs. 1,991.49
(ii) 35mm thick
Sqm
Rs. 1,937.66
(ii) 30mm thick
Sqm
Rs. 1,820.90
Providing, fitting and fixing fully glazed window with sash bars including oxidised
M.S butt hinges (75mmx 60mmx3.15mm) 2nos.on each leaf and 3 nos. on single
leaf, 2nos of 150mmx10mm Aluminium tower bolt, 1no of 100mm Aluminium
handle & 2 nos of aluminium eye hook complete as directed (Glass panes to be
(I) With Sash Bars
(A) With Gamari/ Bansum Wood.
(B)With 1st Class Local wood (Bola)
(II) Without Sash Bars

(A) With Gamari/ Bansum Wood.
(B)With 1st Class Local wood (Bola)
Page-173
CH-33 : RAIN WATER HARVESTING SYSTEM

Item
No.
33.1
Description
Unit
Rate
RAINWATER HERVESTING SYSTEM

For R.C.C Roof
33.1.1 Providing,Fixing, testing &Commissioning of Rain water Hervesting system for 1000
sq.feet roof area with 110 mm uPVC pipe of Class-3 conforming to IS:4985-200
(with uptodate amendment) with extra UV ray protection by Titanium
Dioxide(TiO2) directing the Rainwater to Rainy filter/Pop-up raintap filter
(Excluding Civil Works)
Each
Rs. 113,757.03
Each
Rs. 135,338.47
Ltr.
Rs. 11.56
For GI sheet/Diana Roof

33.1.2 Providing,Fixing, testing &Commissioning of Rain water Hervesting system for 1000
sq.feet roof area with 180 mm uPVC Gutter of Class-3 conforming to IS:4985-200
(with uptodate amendment) with extra UV ray protection by Titanium Dioxide(TiO2 )
along the outer periphery of the GCI/Diana roof ,110 mm UPVC pipe directing the
Rainwater to Rainy filter/Pop-up raintap filter (Excluding Civil Works)
Storage of Rainwater
33.1.3 Water storage tank ISI Marked, conforming to IS:12701/1996 (with uptodate
amendment). (Excluding Civil Works)
Ch-33 : Rain Water Harvesting
Page-174
CH-34 : ORGANIC WASTE DISPOSAL SYSTEM AND STP

Item
No.
Description
Unit
Rate
Organic Waste Disposal System

34.1
Fully automatic Micro-organism based natural composting system with PLC based
control,insulated oil heating chamber,Stainless Steel (SS304) shaft & mixing blade
to convert organic waste like kitchen waste , canteen waste etc. to organic manure.
a) Capacity 24 Kg
Each
Rs. 579,635.94
b) Capacity 70 Kg
Each
Rs. 1,048,296.88
c) Capacity 125Kg
Each
Rs. 1,666,385.94
d) Capacity 250 Kg
Each
Rs. 2,243,721.88
a) Capacity-10 KLD
Each
Rs. 2,087,501.56
b) Capacity-15 KLD
Each
Rs. 2,223,345.31
c) Capacity-20 KLD
Each
Rs. 2,359,189.06
d) Capacity-30 KLD
Each
Rs. 2,562,954.69
e) Capacity-40 KLD
Each
Rs. 2,834,642.19
f) Capacity-50 KLD
each
Rs. 2,970,485.94
Sewage treatment plant

34.2
Attached growth aerobic Sewage treatment System with FRP treatment chamber
with all components including Tertiary filtration system and clorine dosing system
to achieve treated water quality suitable for reuse or discharge as per CPCB norms.
Ch-34: Organic Waste Disposal System and STP
Page-175
CH-35 : THERMAL INSULATION

Item No.
Unit
Rate
35.1.1 Day Time Use Building:

Providing & Laying of Insuboard over the PCC,
50Mm Thickness.(Make: M/S Supreme or equivalent)
(PCC with proper Slope Over RCC)
Sqm
Rs.1,088.16
35.1.2 24-hours Use Building:

Providing & Laying of Insuboard over the PCC,
75 Mm Thickness.(Make: M/S Supreme or equivalent)
(PCC with proper Slope Over RCC)
Sqm
Rs.1,569.83
35.1.3 Providing & laying of Plastic Sheet (120-150GSM)/Silpaulin (45 GSM) as a vapor
barrier.
Sqm
Rs.59.44
35.1.4 Providing & laying of Geo textile 0f 120 GSM as a separating layer over the
Poly/Plastic sheet.
Sqm
Rs.90.09
35.1.5 Providing & laying of P.C.C. of (1:2:4) 40 mm. Avg. thickness with 40-45 GSM
Glass fiber mesh as reinforcement with proper slope.
Sqm
Rs.6,697.60
35.1.6 Providing & laying of polymer Modified 4mm,Membrane or other water proofing
system over the prime slope PCC surface.
Sqm
Rs.2,456.70
35.1.7 Providing & laying of P.C.C. of (1:2:4) 25 mm. Avg. thickness with
40-45 GSM Glass fiber mesh as reinforcement.
The PCC will be done in panel form of 1m x 1 m. panel with Control joints &
joints are to be sealed with mastic sealant.
Sqm
Rs.6,697.60
35.1
35.2
Description
Over Deck(Roof) Insulation:
SINGLE LAYER SYSTEM OVER CONCRETE DECK / ACCESSIBLE ROOF
(For Hydro & Thermal Insulation with INSUBOARD)
Under Deck (Roof) Insulation:

SINGLE LAYER SYSTEM UNDER DECK THERMAL INSULATION SYSTEM WITH
INSU.BOARD
Rs.0.00
35.2.1 Cleaning of the surface by brush
Sqm
Rs.11.61
35.2.2 Day Time use Building:

Providing & Laying of Insuboard, thickness 50mm of density 32 kgs/m3) over the
RCC ceiling (Plastered Surface) from inside. The insuboard will be fixed over the
wall surface by the PVC Fastner(side lap)
( Make: M/s Supreme or equivalent)
Sqm
Rs.1,125.44
35.2.3 24- hours use Building:

Providing & Laying of Insuboard, thickness 75 mm of density 32 kgs/m3) over the
Sqm
Rs.1,607.11
35.2.4 Providing & laying of wall putty 1mm (Max) thick over the Insuboard's bottom
surface & then painting with non solvent base paint after levelling the surface.
Over the joint self adhesive Glass fibre mesh tape to be provided
Sqm
Rs.188.73
Sqm
Rs.0.00
35.3
Wall Insulation:
Thermal Insulation system of external wall with insuboard and cement plaster
finish
Ch-35: Thermal Insulation
Page-176
Item No.
Description
35.3.1 Providing & laying of insuboard of thickness 50mm of density 32kgs/m3) over the
Brick+ plaster(Plastered surface from outside. The insuboard will be fixed over the
wall surface by PVC Fastner(1250X 600MM) shiplap/Sqr Edge profile and the
insuboard joints will be sealed with self glass fibre adhesive.
Unit
Rate
Sqm
Rs.1,204.66
35.3.2 Providng and laying of plaster (1:4) with GI chicken/PVC Wire Mesh/Glass Fibre
Mesh
Or
Providing or laying of wall putty of 1mm(Max) thick over the insuboard's bottom
surface and then painting
35.4
Rs.0.00
i) Providng and laying of plaster (1:4) with GI chicken/PVC Wire Mesh/Glass Fibre
Mesh
Sqm
Rs.291.39
ii) Providing or laying of wall putty of 1mm(Max) thick over the insuboard's
bottom surface and then painting
Sqm
Rs.188.73
Single Layer System inside the cavity wall
35.4.1 Providing & Laying of Insuboard, thickness 50mm of density 32 kgs/m3) over the
Ch-35: Thermal Insulation
Rs.0.00
Sqm
Rs.1,088.16

SOR Civil Works - Assam PWD Schedule - 2013-14

Uploaded by

Copyright:

Available Formats

SOR Civil Works - Assam PWD Schedule - 2013-14

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SOR Civil Works - Assam PWD Schedule - 2013-14

Uploaded by

Copyright:

Available Formats

Page-1

(b) In hard/ dense soil

(c) In soft or laminated rock or medium shale

(i) Using blasting materials

(ii) Without using blasting materials

(i) Using blasting materials

(b) Above 1.5 m upto 3.00 m depth

(c) Above 3.00 m upto 4.50 m depth

(d) Above 4.50 m upto 6.00 m depth

(d) In medium rock of hard shale

(e) In hard rock

Ch-1 : Earth Work

(a) Within Guwahati city only

(b) Other than Guwahati city

Ch-1 : Earth Work

CH-2: CEMENT CONCRETE WORKS

(a) In prop 1cement: 3 sand :6 coarse aggregate by volume

(b) In prop 1cement: 4 sand :8 coarse aggregate by volume

(c) In prop 1cement: 5 sand :10 coarse aggregate by volume

(d) In prop 1cement: 6 sand :12 coarse aggregate by volume

(a) 35mm thick

(b) 50mm thick

2.2 REINFORCED CEMENT CONCRETE WORKS

N) Without using admixture, plasticiser

b) M20 grade concrete or Prop. 1:1.5:3

c) M25 grade concrete

d) M30 grade concrete

e) M35 grade concrete

Ch-2 : Cement Concrete Work

a) M15 grade concrete or Prop. 1:2:4

b) M20 grade concrete or Prop. 1:1.5:3

c) M25 grade concrete

d) M30 grade concrete

e) M35 grade concrete

b) M20 grade concrete or Prop. 1:1.5:3

c) M25 grade concrete

d) M30 grade concrete

e) M35 grade concrete

a) M15 grade concrete or Prop. 1:2:4

b) M20 grade concrete or Prop. 1:1.5:3

c) M25 grade concrete

d) M30 grade concrete

e) M35 grade concrete

a) M15 grade concrete or Prop. 1:2:4

b) M20 grade concrete or Prop. 1:1.5:3

c) M25 grade concrete

d) M30 grade concrete

e) M35 grade concrete

(B) In super structure from plinth level up to 1st floor level.

P) Using admixture, plasticiser etc

b) M20 grade concrete or Prop. 1:1.5:3

c) M25 grade concrete

d) M30 grade concrete

e) M35 grade concrete

Ch-2 : Cement Concrete Work

b) M20 grade concrete or Prop. 1:1.5:3

c) M25 grade concrete

d) M30 grade concrete