Stainless Steels For Machining: A Designers' Handbook Series

A DESIGNERS'
HANDBOOK
SERIES
STAINLESS STEELS
FOR MACHINING
Committee of Stainless Steel Producers

American Iron and Steel Institute
1000 16th Street, N.W.
Washington, D.C.
TABLE OF CONTENTS
Page
Preface ................................................................................................................ 2
Introduction to Stainless Steels ................................................................. 4
Identification ................................................................................. 4
Corrosion Resistance ..................................................................... 9
High-Temperature Corrosion Resistance ...................................... 19
Mechanical and Physical Properties .............................................. 22
High-Temperature Mechanical Properties .................................... 40
Low-Temperature Mechanical Properties ..................................... 42
The Machinable Family of Stainless Steels ........................................... 44
Free-Machining Stainless Steels ................................................... 46
Buy a Better Bar ............................................................................ 48
Stainless Steels for Screw Machine Operations ............................ 50
Machinability vs. Cost .................................................................. 51
Design Hints for Screw Machine Parts .................................................. 52
Good Shop Practices ..................................................................................... 58
Cleaning and Passivating ............................................................................ 59
The Free-Machining Stainless Steels ...................................................... 60
Types 303 and 303 Se Stainless Steels ......................................... 60
Type 430F Stainless Steel ............................................................. 62
Type 416 Stainless Steel ............................................................... 64
Type 420F Stainless Steel ............................................................. 66
PREFACE
Reference to stainless steel is often made in the singular sense as if
it were one material. Actually there are approximately 150 separate
and distinct compositions, each one formulated to serve specific enduse and/or manufacturing requirements.
Stainless steels are only one segment of the steel spectrum, but they
serve a multitude of applications from brightly polished consumer products to machinery and equipment for tough industrial environments.
The variety of stainless steels available today provides a veritable
palette of properties, from specially formulated alloys capable of performing in the most difficult environments to a wide selection of types
ideally suited for machining or other fabrication operations.
Why Upgrade to Stainless Steels?

Upgrading to stainless steels rewards both manufacturer and user.
Among the more obvious benefits are:
Corrosion and Heat ResistanceStainless steels, depending upon the
composition, resist corrosion by many acids, moisture, atmospheric
conditions, and other aggressive environments at low or high
temperature.
StrengthParts often can be made stronger and tougher with stainless
steels than with mild steels or nonferrous metals . . . including parts
exposed either to high temperatures or to hundreds of degrees below
freezing.
DurabilityThe combined qualities of corrosion resistance and strength
result in products capable of providing a lifetime of useful, trouble-free
service. Accordingly, manufacturers' reputations are enhanced by
products made of stainless.
Low MaintenanceHomeowners and industrial users alike prefer
stainless steels because there is no need for protective coatings or other
special surface treatments that can deteriorate or necessitate periodic
maintenance.
AppearanceWhether a product is highly polished or just routinely
made on a screw machine to a 63 RMS as-machined finish, its surface
presents an enduring bright, metallic lustre.
Fabrication FlexibilityStainless steels can be machined, cold formed,
forged, extruded, or welded by contemporary fabricating tools and
techniques. Designers will find among the stainless steels, properties
capable of meeting a wide range of manufacturing and end-use
requirements.
Selecting a Stainless Steel
Early uses of stainless steels were limited to such applications as

gun barrels, cutlery, and nitric acid tanks. As industry began to exploit
the full potential of these corrosion resistant metals, new compositions
were developed to accommodate requirements for greater resistance to
corrosion, greater strength levels, different fabricating characteristics,
resistance to elevated temperature, etc.
For example, Type 304, one of the most frequently used stainless
steel compositions having application in a broad range of products
from cookware to chemical plant equipment, has several variations.
For greater resistance to corrosion, especially in marine environments,
specifiers often select Type 316, which has a higher alloy content than
Type 304. Type 305, on the other hand, has a lower work-hardening
rate than Type 304 and is better suited to cold forming operations,
while Type 303 is the more machinable variation of Type 304.
Selection of the proper stainless steel from the many types
available requires an evaluation based upon five important criteria.
Listed in order of importance, they are:
Corrosion or Heat Resistancethe primary reason for specifying
stainless steel. The specifier needs to know the nature of the environment and the degree of corrosion or heat resistance required.
Mechanical Propertieswith particular emphasis on strength, at
room, elevated, or low temperature. Generally speaking, the combination of corrosion resistance and strength is the basis for selection.
Fabrication Operationsand how the product is to be made is a
third-level consideration. This includes machining, forming, welding,
etc. For parts requiring more than one fabrication operation, the most
difficult usually takes precedence.
Total CostTo put everything into proper perspective, a total value
analysis is appropriate which will consider not only material and production costs, but the cost-saving benefits of a maintenance-free product having a long life expectancy as well.
AvailabilityThe final step in the selection /specification process is
to determine the availability of the candidate material(s). Depending
on the quantity involved, an inquiry can be prepared and submitted to
a steel service center or directly to a mill that produces stainless steel.
(A list of producers participating in this booklet appears on the back
cover.) Direct contact with one or more producers can be beneficial
because possible alternative, lower-cost materials might be suggested.
Although selection is based primarily on the ability of the material
to meet end-use requirements, specifiers and buyers should not
overlook manufacturing, especially machining, which can be
improved by material selection.
With respect to machining, this booklet helps to explain the differences between stainless steels and other metals, and the differences
from one stainless steel to another. It identifies the stainless steel
types that were developed to improve machining production, and it
demonstrates through illustrative examples that stainless steels are
readily machinable . . . even on high-volume, high-speed automatic
screw machines.
INTRODUCTION TO
STAINLESS STEELS
Stainless steels are iron-base alloys containing 10.5 percent or more
chromium. Other alloying elements may be added during melting, such
as nickel, molybdenum, columbium, or titanium, which serve to
change or enhance certain properties or characteristics.
IDENTIFICATION
Several methods are commonly used to identify stainless steels.
They are:
1. Classification by metallurgical structureaustenitic, ferritic,
martensitic, precipitation hardening, or duplex
2. Designation by the AISI numbering systemnamely 200, 300,
and 400 series numbers
3. Designation by the Unified Numbering System, which ASTM
and SAE developed to apply to all commercial metals and alloys
4. Trade nameswhich are generally used with proprietary or
special analysis stainless steels
5. Abbreviated composition
Table 1 lists all AISI-designated stainless steels, and it shows the corresponding UNS designation for each. Following is a discussion of how
stainless steels are classified by metallurgical structure. While
somewhat technical in nature, a basic knowledge of metallurgical
classification is helpful because stainless steels in each category tend to
have many common characteristics.
Metallurgical Structure
The five categories of stainless steel according to metallurgical
structure are:
1. Austenitic
2. Ferritic
3. Martensitic
4. Precipitation Hardening
5. Duplex
Following is a characterization of each group and identification of the
typical stainless steel(s) in each. Understanding the characteristics of
each category is basic to a better understanding of all stainless steels.
Austenitic stainless steels are those containing chromium, nickel and

manganese or just chromium and nickel as the principal alloying
elements. They are identified as AISI 200 series or 300 series types,
respectively.
The austenitic stainless steels can be hardened only by cold working; heat treatment serves only to soften them. In the annealed condition, they are not attracted to a magnet although some may become
slightly magnetic after cold working.
Table 1
AISI AND UNS NUMBERS
AISI
TYPE
UNS
NUMBER
201
202
205
301
302
302B
303
303Se
304
304H
304L
304Cu
304LN
304N
305
308
309
309S
310
S20100
S20200
S20500
S30100
S30200
S30215
S30300
S30323
S30400
S30409
S30403
S30430
S30453
S30451
S30500
S30800
S30900
S30908
S31000
405
409
429
430
430F
431
S40500
S40900
S42900
S43000
S43020
S43100
403
410
410S
414
416
420
S40300
S41000
S41008
S41400
S41600
S42000
S13800
S15500
S13800
S15500
AISI
TYPE
UNS
NUMBER
Austenitic
310S
316
316H
316F
316L
316LN
316N
317
317L
321
321H
329
330
332
334
347
347H
348
348H
384
S31008
S31600
S31609
S31620
S31603
S31652
S31651
S31700
S31703
S32100
S32109
S32900
N08330
S33200
S33400
S34700
S34709
S34800
S34809
S38400
434
436
439
442
444
446
S43400
S43600
S43900
S44200
S44400
S44600
420F
422
440A
440B
440C
S42020
S42200
S44002
S44003
S44004
S17400
S17700
S17400
S17700
Ferritic
Martensitic
Precipitation Hardening
The 200 and 300 series stainless steels are characterized as having
excellent corrosion resistance, unusually good formability, and the
ability to develop excellent strength characteristics by cold working.
Annealed, they possess maximum corrosion resistance, ductility, good
yield and tensile strength, high impact strength, and freedom from
notch effect.
Typical of this group is Type 304, also widely known as 18-8
stainless steel (which refers to 18 percent chromium, 8 percent nickel).
It is a general-purpose stainless of which there are numerous
modifications.
In these variations,
1. The chromium/nickel ratio has been modified to change the cold
forming characteristics such as in Types 301 and 305.
2. The carbon content has been decreased to prevent carbide
precipitation in weldments such as in Types 304L and 316L.
3. Columbium or titanium has been added to stabilize the structure
for service at high temperature such as in Types 347 and 321. They
also serve to prevent carbide precipitation during welding.
4. Molybdenum has been added or the chromium and nickel contents have been increased to improve corrosion or oxidation
resistance such as in Types 316 and 317, with molybdenum, and
Types 309 and 310 with higher alloy content.
5. Sulfur has been adjusted to improve machining characteristics
such as in Type 303. (The use of selenium to enhance machining
characteristics has, for the most part, been discontinued. Type
303 Se, however, is still produced.)
6. Nitrogen content is increased to enhance strength characteristics
such as in Types 304N and 316N. The 200 series stainless steels,
namely Types 201, 202, and 205, are counterparts to the 300 series
types 301, 302, and 305. In the 200 series manganese replaces
some of the nickel.
Up Productivity,
Reduce Rejects
A manufacturer of sleeves for solenoid activated hydraulic control valves found that,
by using Type 304 of foreign manufacture, it was experiencing excessive tool wear and
unacceptable downtime. A switch to domestically produced Type 304 stainless steel
reduced tool wear and increased machining speeds. Consequently, production went
from 1,000 to 3,000 pieces per 8-hour shift, and rejection rates dropped from
approximately 30 percent to less than 1 percent.
Sleeves are machined on 1- -inch six-spindle Acme screw machines, with drilling,
forming, turning, and reaming.
Ferritic stainless steels are straight-chromium types identified by 400

series numbers. The low carbon-to-chromium ratio in the ferritics
eliminates effects of thermal transformation, which simply means that
they are not hardenable by heat treatment. (They can be hardened
slightly by cold working, however.)
The ferritic 400 series stainless steels are strongly attracted to a
magnet, have good ductility, and have good resistance to corrosion and
oxidation. The corrosion resistance of ferritic stainless steels is
improved by increased chromium and molybdenum contents, while
ductility, toughness, and weldability are improved by reducing carbon
and nitrogen contents. The base composition is Type 430, with
nominally 17 percent chromium. The free-machining ferritic is Type
430F.
The development of new melting and refining processes, such as
argon-oxygen decarburization (AOD), has resulted in several new ferritic stainless steels with improved characteristics, which can be
classified as follows; those with about 18 percent chromium having
corrosion resistance similar to Type 304, such as Type 444, and those
with more than 18 percent chromium with resistance to corrosion
comparable or superior to Type 316 in many media. Some of the highchromium ferritic types (or super ferritics) have resistance to chlorides
previously obtainable only in high-nickel and titanium alloys.
Martensitic stainless steels are also straight-chromium types bearing
AISI 400 series numbers, but having a carbon-to-chromium ratio
higher than the ferritic group. Consequently, when cooled rapidly from
high temperature, they do harden, and in some cases to tensile
strengths exceeding 200,000 psi.
The martensitic 400 series types resist corrosion in mild environments (atmosphere, fresh water, weak acids, etc.); they have fairly
good ductility; and they are always strongly magnetic. Typical of the
martensitic grades is Type 410 with 12 percent chromium. Some of the
martensitics have been modified to improve machinability, such as
Types 416 and 420F.
Precipitation Hardening. As just noted, cold working of the
austenitics and rapid cooling from high temperature of the martensitics are two methods for increasing strength and hardness of
stainless steels. In precipitation hardening stainless steels tensile and
yield strengths (in some cases exceeding 300,000 psi) can be
achieved by a low-temperature (about 900F) aging treatment in
combination with cold working.
The precipitation hardening stainless steels are especially useful
because fabrication can be completed in an "annealed" condition and
then the component uniformly hardened without the requirement of
cold working or the necessity of dealing with the problems of distortion and heavy scaling associated with high temperature thermal
treatments.
7
Typical of the precipitation hardening grades, identified by UNS

numbers (which also serve as AISI numbers), are Types S13800,
S15500, S17400 and S17700. (The UNS numbers closely resemble
original PH numbers such as 13-8PH*, 17-4PH*, etc.)
Prior to hardening, the machinability of the precipitation hardening
stainless steels is about equal to or slightly less than Type 304 in the
annealed condition. For example, Type S17700 has a machinability
rating of 45, in comparison to Type 416 stainless steel at 100 percent.
The corrosion resistance of these steels in the hardened condition is
about equal to that of Type 304.
* Trademark, Armco, Inc.
Duplex stainless steels are dual phase materials with austenite and
ferrite in a close to 50-50 balance. Typical characteristics include
excellent strength and corrosion resistance and good fabrication
properties, especially the newer nitrogen containing grades.
Type 329 is a duplex stainless steel that has wide application in
nitric acid service. It contains 26 percent chromium, which gives it
good resistance in chloride environments. The newer duplex materials
with nitrogen (S31803 and S32550) are readily weldable, which frequently was a problem with Type 329. They are used extensively in oil
and gas production and chemical processing.
Receptacle
TYPE 303 STAINLESS STEEL
PRODUCT
Nuclear Connector
COMPONENT
Receptacle Shell
MATERIAL:
Type 303 Stainless Steel
BAR STOCK:
Hollow Bar 2Inch Square OD and

13/16 Inch ID
MACHINE TOOL:
Acme 3Inch Automatic
PRIMARY OPERATIONS:
Turn, Form, Bore, and Cut-Off
GROSS PRODUCTION:
76 Parts Per Hour
SFPM:
161 (Smallest Diameter)
RPM:
471
TOLERANCES:
0.002 Inch
FINISH:
63 Micro-Inch
CORROSION RESISTANCE
Chromium is the alloying element that imparts to stainless steels
their corrosion-resistance qualities. It does this by combining with
oxygen to form a thin, transparent chromium-oxide protective film on
the metal surface (Figure 1).
The chromium-oxide film is stable and protective in normal
atmospheric or mild aqueous environments, and it can be improved
by higher chromium, by nickel, molybdenum, and/or other alloying
elements. Chromium improves film stability; molybdenum and
chromium increase resistance to chloride penetration; and nickel
improves film resistance in strong acid environments.
In the event that the protective (passive) film is disturbed or even
destroyed, however, it willin the presence of oxygen in the
environmentreform and continue to give maximum protection.
Figure 1
EFFECT OF CHROMIUM CONTENT ON CORROSION RATE
(In Normal Atmosphere)
Material Selection
for Corrosive Environments
Many variables characterize a corrosive environment i.e.,
chemicals and their concentration, atmospheric conditions,
temperature, time, flow rate, etc. so it is difficult to say which
stainless steel to use without knowing the exact nature of the environment. However, there are guidelines.
One of the three most widely used stainless steels (Type 304, 430,
or 410) is a good starting point in the selection process, because these
types are the most readily available.
Type 304 serves a wide range of applications. It withstands ordinary
rusting in architecture, it is strongly resistant in food-processing environments (except possibly for high-temperature conditions involving
high acid and chloride contents), it resists organic chemicals, dyestuffs,
and a wide variety of inorganic chemicals. Type 304 resists nitric acid
well and sulfuric acids at moderate temperature and concentrations. It
is used extensively for storage of liquified gases, equipment for use at
cryogenic temperatures, appliances and other consumer products,
kitchen equipment, hospital equipment, transportation, and wastewater treatment.
Type 316 contains slightly more nickel than Type 304 and 2-3 percent
molybdenum, giving it better resistance to corrosion than Type 304,
especially in chloride environments that tend to cause pitting. Type
316 was developed for use in sulfite pulp mills because it resists
sulfuric acid compounds. Its use has been broadened, however, to
handling many chemicals in the process industries.
Type 317 contains 3-4 percent molybdenum and more chromium than
Type 316 for even better resistance to pitting.
Type 430 has lower alloy content than Type 304 and is used for highly
polished trim applications in mild atmospheres. It is also used in nitric
acid and food processing.
Type 410 has the lowest alloy content of the three general-purpose
stainless steels and is selected for highly stressed parts needing the
combination of strength and corrosion resistance, such as fasteners.
Type 410 resists corrosion in mild atmospheres, steam, and many mild
chemical environments.
Table 2 lists the relative corrosion resistance of the AISI-numbered
stainless steels in seven broad categories of corrosive environments.
Table 3 details more specific environments in which various grades a
used, such as acids, bases, organics, and pharmaceuticals.
10
Table 2
RELATIVE CORROSION RESISTANCE OF AISI STAINLESS STEELS
ATMOSPHERIC
MILD ATMOSTYPE
UNS
PHERIC AND
NUMBER NUMBER FRESH WATER INDUSTRIAL MARINE
201
202
205
301
302
302B
303
303 Se
304
304L
304 Cu
304N
305
308
309
309S
310
310S
314
316
316F
316L
316N
317
317L
321
329
330
347
348
384
403
405
409
410
414
416
420
(S20100)
(S20200)
(S20500)
(S30100)
(S30200)
(S30215)
(S30300)
(S30323)
(S30400)
(S30403)
(S30430)
(S30451)
(S30500)
(S30800)
(S30900)
(S30908)
(S31000)
(S31008)
(S31400)
(S31600)
(S31620)
(S31603)
(S31651)
(S31700)
(S31703)
(S32100)
(S32900)
(N08330)
(S34700)
(S34800)
(S38400)
(S40300)
(S40500)
(S40900)
(S41000)
(S41400)
(S41600)
(S42000)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
CHEMICAL
SALT
WATER
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
MILD
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
OXIDIZING REDUCING
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Table 2 continued on next page
11
Table 2 Continued
RELATIVE CORROSION RESISTANCE OF AISI STAINLESS STEELS
ATMOSPHERIC
MILD ATMOSTYPE
UNS
PHERIC AND
NUMBER NUMBER FRESH WATER INDUSTRIAL
MARINE
420F
422
429
430
430F
431
434
436
440A
440B
440C
442
446
(S42020)
(S42200)
(S42900)
(S43000)
(S43020)
(S43100)
(S43400)
(S43600)
(S44002)
(S44003)
(S44004)
(S44200)
(S44600)
(S13800)
(S15500)
(S17400)
(S17700)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
CHEMICAL
SALT
WATER
MILD
x
x
x
x
x
x
x
x
x
x
x
x
x
OXIDIZING
REDUCING
x
x
x
x
x
x
x
x
x
x
*The "X" notations indicate that a specific stainless steel type may be considered as resistant to the corrosive environment
categories.
This list is suggested as a guideline only and does not suggest or imply a warranty on the part of the American Iron and
Steel Institute, the Committee of Stainless Steel Producers, or any of the member companies represented on the
Committee. When selecting a stainless steel for any corrosive environment, it is always best to consult with a corrosion
engineer and, if possible, conduct tests in the environment involved under actual operating conditions.
Type 303 =
Long Tool Life
Good Surface Finish
Excellent Parts Production
Type 303 stainless steel spray gun nozzles are machined on six-spindle automatic
screw machines and lathes with high-speed tools. Machining operations range from
rough forming to roll form threading. A Poly Gun attachment is used to machine the
square. Secondary machining is done in two stepsfour holes each. The nozzle tip is
tapered on a bench lathe.
The nozzles are designed for use with potentially corrosive liquids, such as
vitreous enamel or heavy alkaline paints. These paints flow through the gun into the
nozzle where they are introduced to air intake. At the nozzle tip, air helps to atomize
the paint, producing the desired spray.
Type 303 is supplied in 1 1/8 inch bars.
12
Table 3
WHERE DIFFERENT GRADES ARE USED
ENVIRONMENT
Acids
Hydrochloric acid
GRADES
Stainless generally is not recommended except when solutions are

very dilute and at room temperature.
"Mixed acids"
There is usually no appreciable attack on Type 304 or 316 as long as

sufficient nitric acid is present.
Nitric acid
Type 304L or 430 is used.
Phosphoric acid
Type 304 is satisfactory for storing cold phosphoric acid up to 85%

and for handling concentrations up to 5% in some unit processes of
manufacture. Type 316 is more resistant and is generally used for
storing and manufacture if the fluorine content is not too high. Type
317 is somewhat more resistant than Type 316. At concentrations up
to 85%, the metal temperature should not exceed 212F (100C) with
Type 316 and slightly higher with Type 317. Oxidizing ions inhibit
attack and other inhibitors such as arsenic may be added.
Sulfuric acid
Type 304 can be used at room temperature for concentrations over

80%. Type 316 can be used in contact with sulfuric acid up to 10%
at temperatures up to 120F (50C) if the solutions are aerated; the
attack is greater in airfree solutions. Type 317 may be used at
temperatures as high as 150F (65C) with up to 5% concentration.
The presence of other materials may markedly change the
corrosion rate. As little as 500 to 2000 ppm of cupric ions make it
possible to use Type 304 in hot solutions of moderate
concentration. Other additives may have the opposite effect.
Sulfurous acid
Type 304 may be subject to pitting, particularly if some sulfuric acid

is present. Type 316 is usable at moderate concentrations and
temperatures.
Bases
Ammonium hydroxide, sodium
hydroxide, caustic
solutions
Organics
Acetic acid
Steels in the 300 series generally have good corrosion resistance at

virtually all concentrations and temperatures in weak bases, such as
ammonium hydroxide. In stronger bases, such as sodium hydroxide,
there may be some attack, cracking or etching in more concentrated
solutions and at higher temperatures. Commercial purity caustic
solutions may contain chlorides, which will accentuate any attack
and may cause pitting of Type 316 as well as Type 304.
Acetic acid is seldom pure in chemical plants but generally includes

numerous and varied minor constituents. Type 304 is used for a wide
variety of equipment including stills, base heaters, holding tanks,
heat exchangers, pipelines, valves and pumps for concentrations up
to 99% at temperatures up to about 120F (50C). Type 304 is also
satisfactory for contact with 100% acetic acid vapors, andif small
amounts of turbidity or color pickup can be toleratedfor room
temperature storage of glacial acetic acid. Types 316 and 317 have
the broadest range of usefulness, especially if formic acid is also
present or if solutions are unaerated. Type 316 is used for fractionating equipment, for 30 to 99% concentrations where Type 304
cannot be used, for storage vessels, pumps and process equipment
13
Table 3 Continued
WHERE DIFFERENT GRADES ARE USED
ENVIRONMENT
14
GRADES
Acetic acid
continued
handling glacial acetic acid, which would be discolored by Type 304.

Type 316 is likewise applicable for parts having temperatures above
120F (50C), for dilute vapors and high pressures. Type 317 has
somewhat greater corrosion resistance than Type 316 under severely
corrosive conditions. None of the stainless steels has adequate
corrosion resistance to glacial acetic acid at the boiling temperature
or at superheated vapor temperatures.
Aldehydes
Type 304 is generally satisfactory.
Amines
Type 316 is usually preferred to Type 304.
Cellulose acetate
Type 304 is satisfactory for low temperatures, but Type 316 or Type
317 is needed for high temperatures.
Citric, formic and

tartaric acids
Type 304 is generally acceptable at moderate temperatures, but Type

316 is resistant to all concentrations at temperatures up to boiling.
Esters
From the corrosion standpoint, esters are comparable with organic

acids.
Fatty acids
Up to about 300F (150C), Type 304 is resistant to fats and fatty

acids but Type 316 is needed at 300 to 500F (150 to 260C) and
Type 317 at higher temperatures.
Paint vehicles
Type 316 may be needed if exact color and lack of contamination are
important.
Phthalic anhydride
Type 316 is usually used for reactors, fractionating columns, traps,

baffles, caps and piping.
Soaps
Type 304 is used for parts such as spray towers, but Type 316 may be
preferred for spray nozzles and flake-drying belts to minimize
offcolor product.
Synthetic
detergents
Type 316 is used for preheat, piping, pumps and reactors in catalytic
hydrogenation of fatty acids to give salts of sulfonated high
molecular alcohols.
Tall oil (pulp and

paper industry)
Type 304 has only limited usage in tall-oil distillation service. Highrosin-acid streams can be handled by Type 316L with a minimum
molybdenum content of 2.75%. Type 316 can also be used in the more
corrosive high-fatty-acid streams at temperatures up to 475F (245C),
but Type 317 will probably be required at high temperatures.
Tar
Tar distillation equipment is almost all Type 316 because coal tar has
a high chloride content; Type 304 does not have adequate resistance
to pitting.
Urea
Type 316L is generally required.
Pharmaceuticals
Type 316 is usually selected for all parts in contact with the product
because of its inherent corrosion resistance and greater assurance of
product purity.
The foregoing comments on the use of stainless steels in certain

environments are based on a long history of successful application,
but they are intended only as guidelines. Small differences in chemical
content and temperature, such as might occur during processing
upsets, can affect corrosion rates. For instance, there is a rule of thumb
that states the corrosion rate of a material doubles for each 30C rise
in temperature.
Service tests are most reliable in determining optimum material,
and ASTM G-4 is a recommended practice for carrying out such tests.
Tests should cover conditions both during operation and shut-down.
For instance, sulfuric, sulfurous and polythionic acid condensates
formed in some processes during shutdown may be more corrosive
than the process stream itself. Tests should be conducted under the
worst operating conditions anticipated.
Several standard reference volumes discuss corrosion and corrosion
control, including Uhlig's Corrosion Handbook; LaQue and Copsons'
Corrosion Resistance Of Metals and Alloys; Fontana and Greens'
Corrosion Engineering; A Guide to Corrosion Resistance by Climax
Molybdenum Company; the Corrosion Data Survey by the National
Association of Corrosion Engineers; and the ASH Metals Handbook.
Corrosion data, specifications, and recommended practices relating to
stainless steels are also issued by ASTM.
Stainless steels resist corrosion in a broad range of conditions, but
they are not immune to every environment. Misapplications of
stainless steels are rare and are usually avoided by specifiers and users
who recognize conditions detrimental to stainless steels and understand how to specify to avoid problems. The types of corrosion and
nature of environments that are more likely to be of concern are: pitting, crevice attack, stress-corrosion cracking, and intergranular
corrosion.
Pitting occurs when the protective chromium-oxide film breaks
down in small isolated spots, such as when halide salts contact the
surface. Once started, the attack may accelerate because of
differences in electric potential between the large area of passive
surface vs. the active pit.
Pitting is avoided in many environments by using stainless steels
containing molybdenum, such as Type 316 or 317.
S18200 for Meat Processing Trolley Stud
A manufacturer of meat processing trolleys had been using Type 303 stainless for
Sani-Trolley studs, which hold the trolley wheels and brackets. Machining of the part
was difficult, however, so the company looked for a stainless that would machine
more freely, yet provide corrosion resistance matching or exceeding that of Type
303.
A test program of salt spray bath and in-service use resulted in the selection of
S18200 stainless steel. The machining sequence is: form cut, shave cut, roll threads,
drill, wobble broach, and cutoff.
15
Crevice corrosion results from local differences in oxygen concentration associated with deposits on the metal surface, gaskets, lap
joints, or crevices under bolt or rivet heads where small amounts of
liquid can collect and become stagnant.
The material responsible for the formation of a crevice need not be
metallic. Wood, plastics, rubber, glass, concrete, asbestos, wax, and
living organisms have all been reported to cause crevice corrosion.
Once attack begins within the crevice, its progress is very rapid, and it
is frequently more intense in chloride environments. For this reason,
the stainless steels containing molybdenum are often used to minimize
the problem. Notwithstanding, the best solution to crevice corrosion is
a design that eliminates crevices.
Stress-Corrosion Cracking is caused by the combined effects of
temperature, tensile stress and corrosive environment. Many metal
systems have been known to experience stress-corrosion cracking
brass in ammonia, carbon steel in nitrate solutions, titanium in
methanol, aluminum in sea water, and gold in acetic acid. Stainless
steels are susceptible to stress-corrosion cracking in chloride environments. (Cracking may also occur in other aggressive environments,
such as hydrogen sulfide.)
It is necessary for tensile stress, chlorides and elevated temperature
all to be present for stress-corrosion cracking to occur. Wet-dry or heat
transfer conditions, which promote the concentration of chlorides, are
particularly aggressive with respect to initiating stress-corrosion
cracking.
While the mechanism of stress-corrosion cracking is not fully
understood, laboratory tests and service experience have resulted in
methods to minimize the problem. For instance, the duplex stainless
steels exhibit superior resistance to chloride stress-corrosion cracking;
plus having good resistance to pitting.
The ferritic stainless steels, such as Types 405, 430 and 444 should
also be considered when the potential exists for stress-corrosion
cracking.
Fastener
16
PRODUCT:
Anchor Bolts
COMPONENT:
Threaded Fastener
MATERIAL:
BAR STOCK:
0.681 Inch Round Bar, Centerless Ground
OPERATIONS:
Form, Thread, and Cut-Off
SFPM:
90
RPM:
500
TOLERANCES:
0.0015 Inch
Intergranular Corrosion. When austenitic stainless steels are heated

or cooled through the temperature range of about 800-1650F, the
chromium along grain boundaries tends to combine with carbon to
form chromium carbides. Called carbide precipitation, or
sensitization, the effect is a depletion of chromium and the lowering
of corrosion resistance in areas adjacent to the grain boundary. This is
a time-temperature dependent phenomenon, as indicated in Figure 2.
Figure 2
EFFECT OF CARBON CONTENT ON
CARBIDE PRECIPITATION
Time required for formation of carbide precipitation in stainless steels with various
carbon contents. Carbide precipitation forms in the areas to the right of the various
carbon-content curves. Within time-periods applicable to welding, chromium-nickel
stainless steels with 0.05% carbon would be quite free from grain boundary
precipitation.
17
Sensitization may result from slow cooling from annealing

temperatures, stress-relieving in the sensitization range, or welding.
Due to the longer time at temperature of annealing or stress-relieving,
it is possible that the entire piece of material will be sensitized,
whereas the shorter time at temperature characteristic of welding can
result in sensitization of a band, usually 1/8 to inch wide, adjacent to
but slightly removed from the weld. This region is known as the heataffected-zone or HAZ.
Intergranular corrosion depends upon the magnitude of the sensitization and the aggressiveness of the environment to which the sensitized material is exposed. Many environments do not cause intergranular corrosion in sensitized austenitic stainless steels.
Carbide precipitation and subsequent intergranular corrosion in
austenitic stainless steels have been thoroughly investigated; the
causes are understood and methods of prevention have been devised.
These methods include:
1. Use of stainless steel in the annealed condition.

2. Selection of the low-carbon (0.030 percent maximum)
stainless steels for weld fabrication. Low-carbon grades are
Types 304L, 316L, and 317L. The less carbon available to
combine with the chromium, the less likely is carbide
precipitation to occur. However, the low-carbon grades may
become sensitized at extremely long exposures to temperatures
in the sensitization range.
3. Selection of a grade stabilized with titanium or columbium.
The protection obtained is based upon the greater affinity of
titanium and columbium for carbon as compared to chromium.
Columbium stabilization is preferred because its carbides
are more readily retained in welds and it is easier to add in the
steelmaking process. However, the use of columbium
stabilized steel requires additional care in welding.
4. Redissolving carbides by annealing parts after fabrication,
although this is not always practical.
Long Tool Life, Fewer Rejects
The excellent machining properties of Types 316 and 416 are responsible for long
tool life and a minimum number of rejects in the production of gland nuts, which are
one of four parts used in valve body assemblies of Union-type superpressure
connectors. High strength, excellent corrosion resistance, and good machining
characteristics are very important in this application.
The gland nut is 1- inch hexagonal by 1-3/8 inch overall length, with 1-1/8 inch-12
UNF-2A threads. It is produced on Warner & Swasey five spindle automatic equipment
with the fabrication sequence as follows: spot drill and rough turn; undersize drill and
form for threads; drill 9/16 inch diameter for through hole; ream 19/32 inch diameter for
through hole; roll threads; counterbore with 2 lip carbide tool; and cutoff.
18
It should be understood that the above steps are necessary only if

the service environment is known to be capable of causing intergranular corrosion.
Although sensitization can also occur in the ferritic stainless steels
heated to 1700F and water quenched or air cooled, it is far less likely
to occur than with austenitic grades; and intergranular corrosion has
not been a problem in these steelsexcept for a narrow band in the
heat-affected-zone close to welds. (Several ferritic stainless steels
either have low carbon content or are stabilized to prevent sensitization
during welding.)
HIGH TEMPERATURE CORROSION RESISTANCE
Stainless steels have been widely used for elevated-temperature service, so fundamental and practical data concerning their resistance to
corrosion are available.
When stainless steels are exposed at elevated temperatures, changes
can occur in the nature of the protective chromium-oxide film. For
example, at mildly elevated temperatures in an oxidizing gas, a protective oxide film is formed. In an environment containing sulfur-bearing
gases, the film will be in the form of sulfides, which may also be
protective.
In more aggressive environments, with temperatures above 1600F,
the surface film may break down with sudden increase in scaling.
Depending on alloy content and environment, the film may be self
healing for a period of time followed by another breakdown.
Under extreme conditions of high temperature and corrosion, the
surface film may not be protective at all.
For these reasons, the following data should serve only as a starting
point for material selection, not as a substitute for service tests.
Machining Consistency
Makes
Manufacturer Competitive
Very close tolerance and critical surface finish are musts in the manufacture of
these connector parts for electronic cable assemblies. So are high production rates.
Using Type 303 stainless steel, average production time per part is 140 seconds;
critical tolerances are held to 0.0005 inch; and surface finishes of 32 RMS are
achieved.
Connector bodies are machined from inch round stock on a Brown and Sharpe
Ultramatic screw machine. Production sequence involves forming, drilling, boring,
and tapping. Threading and knurling are also required.
19
Oxidation
In nonfluctuating-temperature service, the oxidation resistance (or
scaling resistance) of stainless steels depends on chromium content,
as indicated by the curve in Figure 3. Steels with less than 18 percent
chromium (ferritic grades primarily) are limited to temperatures
below 1500F. Those containing 18-20 percent chromium are useful
to temperatures of 1800F, while adequate resistance to scaling at
temperatures up to 2000F requires a chromium content of at least 25
percent, such as Type 309, 310, or 446.
Figure 3
EFFECT OF CHROMIUM CONTENT ON
SCALING RESISTANCE (At 1800 F)
20
In many processes, isothermal (constant temperature) conditions are

not maintained and process temperatures vary. Expansion and contraction differences between the base metal and the protective film (or
scale) during heating and cooling may cause cracking and spalling of
the protective scale. This allows the oxidizing media to attack the
exposed metal surface.
The spalling resistance of the austenitic stainless steels is greatly
improved at higher nickel levels. Nickel reduces the thermal expansion
differential between alloy and oxide film and thereby reducing stresses
at the alloy-oxide interface during cooling. Also, the ferritic
chromium- molybdenum stainless steels have a fairly low coefficient
of thermal expansion, which tends to reduce the spalling tendency.
An increase in corrosion rates can be expected in the presence of
water vapor. Figure 4 illustrates the effect of moist air on the oxidation
of Types 302 and 330. Type 302 undergoes rapid corrosion in wet air
at 2000F, whereas a protective film is formed in dry air. The higher
nickel Type 330 is less sensitive to the effects of moisture, so it is
assumed that increased chromium and nickel permit higher operating
temperatures in moist air. Types 309 and 310 are superior at
temperatures greater than 1800F, and Type 446 is usable at temperatures approaching 2000F.
Figure 4
OXIDATION OF TYPES 302 AND 330
IN WET AND DRY AIR
21
A note of caution about stainless steels at high temperatures in

stagnant oxidizing environments. The protective film breaks down in
the presence of certain metal oxides, causing accelerated attack. For
instance, austenitic types are susceptible to attack in the presence of
lead oxide at temperatures as low as 1300F. Vanadium oxide, found
in fuel ash, may cause failure of Types 309 and 310 at 1900F when
water vapor is present. Molybdenum oxide behaves in a similar
manner.
Sulfidation
Sulfur in various forms and even in relatively small quantities
accelerates corrosion in many environments. Sulfur dioxide,
hydrogen sulfide, and sulfur vapor are among the most corrosive
forms. Sulfur vapor and hydrogen sulfide are considerably more
aggressive than sulfur dioxide.
Sulfur attack, although closely related to oxidation, is more severe.
Metal sulfides melt at lower temperatures than comparable oxides,
and they may fuse to metal surfaces. Also, sulfides are less likely to
form tenacious, continuous, protective films. Fusion and lack of
adherence result in accelerated corrosion.
The resistance of stainless steels to sulfidation depends on
chromium content.
Other High Temperature Environments
Data are available on the corrosion-resistance of stainless steels in
other high-temperature environments, such as their use for liquid-metal
environments. Designers are referred to the following publications for
additional data on high-temperature applications: Selection of Stainless
Steels, ASM Engineering Bookshelf. Corrosion Resistance of the
Austenitic Stainless Steels in High-Temperature Environments, by
International Nickel Inc. High-Temperature Characteristics of Stainless
Steels, Committee of Stainless Steel Producers, American Iron and Steel
Institute.
MECHANICAL AND PHYSICAL PROPERTIES
Austenitic Stainless Steels
The austenitic stainless steels cannot be hardened by heat treatment
but can be strengthened by cold work, and thus they exhibit a wide
range of mechanical properties. At room temperature, austenitic
stainless steels may exhibit yield strengths between 30 and 200 ksi,
depending on composition, amount of cold work and size. They also
exhibit good ductility and toughness even at high strengths, and this
good ductility and toughness is retained to cryogenic temperatures.
The chemical compositions, nominal mechanical and physical properties of annealed austenitic stainless steels are given in Table 4.
22
TABLE 4
AUSTENITIC STAINLESS STEELS CHEMICAL COMPOSITIONS and MECHANICAL PROPERTIES
Chemical Analysis % (Max. unless noted otherwise)
AISI
Type
(UNS No.)
201
(S20100)
202
(S20200)
205
(S20500)
301
(S30100)
302
(S30200)
302B
(S30215)
303
(S30300)
303Se
(S30323)
304
(S30400)
304H
(S30409)
304L
(S30403)
304Cu
(S30430)
304LN
(S30453)
304N
(S30451)
305
(S30500)
Mn
Si
Cr
Ni
0.15
0.060
0.030
0.75
0.060
0.030
0.75
0.12/
0.25
0.15
5.50/
7.50
7.50/
10.00
14.00/
15.50
2.00
0.060
0.030
0.75
0.045
0.030
0.75
0.15
2.00
0.045
0.030
0.75
0.15
2.00
0.045
0.030
0.15
2.00
0.20
0.15
2.00/
3.00
1.00
0.15
2.00
0.20
0.060
1.00
0.08
2.00
0.045
0.030
0.75
0.04/
0.10
0.030
2.00
0.045
0.030
0.75
2.00
0.045
0.030
0.75
0.08
2.00
0.045
0.030
0.75
0.030
2.00
0.045
0.030
0.75
0.08
2.00
0.045
0.030
0.75
0.12
2.00
0.045
0.030
0.75
16.00/
18.00
17.00/
19.00
16.50/
18.00
16.00/
18.00
17.00/
19.00
17.00/
19.00
17.00/
19.00
17.00/
19.00
18.00/
20.00
18.00/
20.00
18.00/
20.00
17.00/
19.00
18.00/
20.00
18.00/
20.00
17.00/
19.00
3.50/
5.50
4.00/
6.00
1.00/
1.75
6.00/
8.00
8.00/
10.00
8.00/
10.00
8.00/
10.00
8.00/
10.00
8.00/
10.50
8.00/
10.50
8.00/
12.00
8.00/
10.00
8.00/
12.00
8.00/
10.50
10.50/
13.00
0.15
Mo Other
0.25 N
Mechanical Properties
(Annealed bar unless noted otherwise)
Elongation
Yield
in 2"
Strength
Tensile
(0.2% offset) (50.80mm)
Strength
%, min.
ksi, min.
ksi, min.
75
40
40
Hardness Product
(Rockwell) Form
max.
0.25 N
75
40
40
0.32/
0.40 N
110
65
30
B98
75
a
(185)
75
b
(125)
75
30
a
(140)
30
b
(100)
30
40
a
(9)
40
b
(12)
40
B92
a
(C41)
85
35
50
85
35
50
262
(Brinell)
262
(Brinell)
75
b
(125)
75
30
b
(100)
30
40
b
(10)
40
0.10 N
70
25
40
3.00/
4.00 Cu
0.10/
0.16 N
0.10/
0.16 N
65-85
30
70
B70
75
30
30
B92
80
35
30
75
30
40
0.10 N
0.15
(min) Se
0.10 N
B92
Sheet
23
24
AISI
Type
(UNS No.)
308
(S30800)
309
(S30900)
309S
(S30908)
310
(S31000)
310S
(S31008)
316
(S31600)
316H
(S31609)
316F
(S31620)
316L
(S31603)
316LN
(S31653)
316N
(S31651)
317
(S31700)
317L
(S31703)
321
(S32100)
0.045
0.20
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
0.20
0.08
0.25
0.08
0.08
0.04/
0.10
0.08
0.030
0.030
0.08
0.08
0.030
0.08
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
Mn
2.00
C
0.08
P
0.045
0.030
0.030
0.030
0.030
0.030
0.030
0.10
0.030
0.030
0.030
0.030
0.030
0.030
S
0.030
0.75
0.75
0.75
0.75
0.75
0.75
1.00
0.75
0.75
1.50
1.50
1.00
1.00
Si
1.00
Cr
19.00/
21.00
22.00/
24.00
22.00/
24.00
24.00/
26.00
24.00/
26.00
16.00/
18.00
16.00/
18.00
16.00/
18.00
16.00/
18.00
16.00/
18.00
16.00/
18.00
18.00/
20.00
18.00/
20.00
17.00/
19.00
Ni
10.00/
12.00
12.00/
15.00
12.00/
15.00
19.00/
22.00
19.00/
22.00
10.00/
14.00
10.00/
14.00
10.00/
14.00
10.00/
14.00
10.00/
14.00
10.00/
14.00
11.00/
15.00
11.00/
15.00
9.00/
12.00
Chemical Analysis % (Max. unless notedotherwise)
2.00/
3.00
2.00/
3.00
1.75/
2.50
2.00/
3.00
2.00/
3.00
2.00/
3.00
3.00/
4.00
3.00/
4.00
Mo
5(C+N)(min)/
0.70 (max) Ti
0.10 N
0.10 N
0.10/
0.16 N
0.10/
0.16 N
0.10 N
0.10 N
0.10 N
Other
75
85
75
80
75
75
85
75
b
(125)
75
75
75
75
75
30
35
30
35
30
30
35
30
b
(100)
30
30
30
30
30
40
75
40
30
40
40
40
40
(12)b
40
40
40
40
40
Elongation
Yield
in 2"
Strength
Tensile
(0.2% offset) (50.80mm)
Strength
%, min.
ksi, min.
ksi, min.
75
30
40
TABLE 4 Continued
AUSTENITIC STAINLESS STEELS CHEMICAL COMPOSITIONS and MECHANICAL PROPERTIES
B95
C20-28
Hardness
(Rockwell)
max.
Sheet
Product
Form
25
2.00
2.00
2.00
0.08
0.04/
0.10
0.08
2.00
0.045
0.045
0.045
0.040
0.040
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
1.00
0.75
0.75
0.75
0.75
0.75
0.75/
1.50
0.75
0.75
0.75
15.00/
17.00
17.00/
19.00
17.00/
19.00
23.00/
28.00
17.00/
20.00
19.00/
23.00
18.00/
22.00
17.00/
19.00
17.00/
19.00
17.00/
19.00
17.00/
19.00
9.00/
13.00
9.00/
12.00
2.50/
5.00
34.00/
37.00
30.00/
34.00
18.00/
22.00
9.00/
13.00
9.00/
13.00
9.00/
13.00
1.00/
2.00
0.60 Ti
0.60 A1
0.60 Ti
0.60 Al
10 xC(min)/
1.00(max) Cb+Ta
8xC(min)/
1.00(max) Cb+Ta
10xC(min)/
1.00(max)Cb +Ta
0.10 Ta, 0.20 Co
8xC(min)/
1.00(max)Cb+Ta
0.10 Ta, 0.20 Co
4(C+N)(min)/
0.70(max) Ti
60-80
75
75
75
75
80
80-120
70
105
75
30
30
30
30
30
35-90
30
80
30
40
40
40
40
38
50-25
30
25
40
140-217
(Brinell)
Strip
Notes: Data are for information only and should not be used for design purposes. For design and specification, refer to appropriate ASTM specifications. Data were obtained from various
sources, including AISI Steel Products Manuals, ASTM Specifications, and individual company literature.
a = Full hard condition.
b = Cold finished, for sizes up to in. inclusive, A276 Condition B.
c = ASTM A276-Condition H.
d = A565 Condition HT, heat treated 1900F, air or oil quench and tempered at 1150F minimum for 2 hours minimum.
e = Solution treated condition.
0.08
1.00
0.08
384
(S38400)
0.045
2.00
0.08
2.00
0.045
2.00
0.08
0.04/
0.10
0.040
2.00
0.040
0.045
2.00
0.04/
0.10
0.08
348H
(S34809)
321H
(S32109)
329
(S32900)
330
(N08330)
332
(S33200)
334
(S33400)
347
(S34700)
347H
(S34709)
348
(S34800)
26
Density
Lb/Cu.In.
0.28
0.28
0.28
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
Stainless
Steel
Type
201
202
205
301
302
302B
303
303Se
304
304H
304L
304Cu
304LN
304N
305
308
309
309S
310
310S
316
316H
28.0
28.0
29.0
29.0
29.0
29.0
28.0
a
28.0
a
28.0
a
28.0
a
28.0
a
28.0
a
28.0
a
28.0
a
28.0
a
28.0
a
28.5
a
28.0
28.0
28.6
28.6
Modulus
of
Elasticity
psi
6
x 10
74
74
78
78
78
78
72
72
72
72
72
72
72
72
72
72
72
72
72
69
69
Specific
Electrical
Resistance
at 68F
Microhm-Cm
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
Specific
Heat
Btu/Lb/F
32-212F
9.4
9.4
8.2
8.2
9.0
9.0
9.4
9.4
9.4
9.4
9.4
9.4
9.4
9.4
9.4
9.4
9.4
8.8
9.4
9.4
Thermal
Conductivity
BTU/ft/hr/F
(68-212F)
8.9
8.9
8.8
8.8
8.3
8.3
8.7
(9.2)
(68-212F)
(9.4)
(68-392F)
9.4
9.6
9.0
9.6
9.6
9.6
9.6
9.6
9.6
9.6
9.6
9.6
32-212F
9.0
9.0
9.0
9.0
9.3
9.3
9.7
9.7
9.4
9.4
9.6
9.6
10.9
(10.6)
(32900F)
(10.4)
(68851F)
9.5
10.1
9.9
10.2
10.0
10.8
9.9
10.2
9.9
10.2
9.9
10.2
9.9
10.2
9.9
10.2
9.0
9.9
10.2
9.9
10.2
9.9
10.2
9.7
10.2
32-600F 32-1000F
10.3
10.3
9.7
9.7
10.0
10.0
(11.3)
(32-1400F)
(11.4)
(68-1472F)
10.4
10.4
11.2
10.4
10.4
10.4
10.4
10.4
10.4
10.4
10.5
10.4
10.4
(11.7)
(68-1700F)
11.0
11.0
11.0
11.0
11.0
11.0
(10.9)
(68-1832F)
(11.5)
(32-1800F)
(11.5)
(32-1800F)
(10.6)
(32-1800F)
(10.6)
(32-1800F)
(11.1)
(32-1500F)
(11.1)
(32-1500F)
11.3
32-1200F 32-1600F
Mean Coefficient of
-6
Thermal Expansion, in/in/F x 10
Table 4 Continued
PHYSICAL PROPERTIES OF AUSTENITIC STAINLESS STEELS
1.02
1.02
1.02
1.02
1.02
1.02
1.02
1.02
(1.02)
(1.02)
1.02
1.02
1.02
1.02
1.02
1.02
1.02
1.005
1.02
1.02
Magnetic
Permeability
max.
1850-2050
1850-2050
1900-2100
1900-2100
1900-2050
1900-2050
1850-2050'
b
1850-2050
b
1850-2050
b
1850-2050
b
1850-2050
b
1850-2050
b
1850-2050
b
1850-2050
b
1850-2050
1850-2050
b
1850-2050
b
1850-2050
b
1850-2050
1950
1850-2050
b
1850-2050
Annealing
Temperature
0.29
0.29
0.29
0.29
0.29
0.29
0.28
0.29
0.29
0.29
0.29
0.29
0.29
0.29
0.29
316LN
316N
317
317L
321
321H
329
330
332
334
347
347H
348
348H
384
28.0
28.0
28.0
28.0
28.0
28.5
27.9
27
28.0
28.0
29.0
28.5
a
28.0
28.0
29.0
a
28.0
79
72
72
72
72
102
99
86
72
72
79
74
74
74
74
74
0.12
0.12
0.12
0.12
0.12
0.11
0.12
0.12
0.12
0.116
0.12
0.12
0.12
0.116
0.12
9.4
9.3
9.3
9.3
9.3
7.2
6.7
9.3
9.3
8.3
9.4
9.4
8.3
9.4
9.6
9.3
9.3
9.3
9.3
(5.6)
(75-200F)
7.8
9.3
9.3
9.3
9.2
8.9
8.9
9.2
8.9
9.9
9.5
9.5
9.5
9.5
(6.5)
(75-700F)
9.0
9.5
9.5
9.5
9.0
9.0
9.7
9.0
10.2
10.3
10.3
10.3
10.3
9.4
9.7
10.3
10.3
10.1
9.7
9.7
10.1
9.7
Notes:
a = In tension. As cold worked, the modulus is lowered. By stress relief heat treatment the lowered modulus may be increased.
b = Cool rapidly from these annealing temperatures.
c = Full annealingcool slowly.
d = Process annealing.
e = Physical properties in the H950 Condition.
f = Physical properties in the H900 Condition.
g = Physical properties in the CH900 Condition.
0.29
0.29
316F
316L
27
(11.1)
(32-1500F)
10.3
(11.1)
(32-1500F)
10.3
10.3
(11.1)
(32-1500F)
10.3
(10.8)
(68-1832F)
10.7
(11.2)
(32-1500F)
10.7
(11.2)
(32-1500F)
(8.0)
(700-1500F)
9.3
9.7
(10.1)
(10.6)
(32-1472F) (32-1832F)
10.6
(11.1)
(32-1500F)
10.6
(11.1)
(32-1500F)
10.6
(11.1)
(32-1500F)
10.6
(11.1)
(32-1500F)
10.4
10.3
1.02
1.02
1.02
1.02
1.02
1.02
1.02
1.02
1.02
1.02
1.02
1900-2100
1850-2050
1850-2050
1850-2050
1850-2050
1750-1800
b
1750-1800
b
1950-2150
2050-2150
2050-2100
1750-2050
1750-2050
1900-2000
1850-2050
b
1850-2050
1850-2050
2000
b
1850-2050
Because austenitic stainless steels can be cold worked to high tensile

and yield strengths, yet retain good ductility and toughness, they meet
a wide range of design criteria. For example, Type 301 can be produced in the following tempers:
TABLE A
Temper
-Hard
-Hard
-Hard
Full-Hard
Tensile Strength
Minimum ksi
125
150
175
185
Yield
Strength
Minimum ksi
75
110
135
140
Ferritic Stainless Steels

Ferritic stainless steels contain approximately 12 percent chromium.
The chemical composition, nominal mechanical and physical properties of the AlSl grades are shown in Table 5.
Solenoid Plunger
TYPE 434F STAINLESS STEEL
28
PRODUCT:
Hot and Cold Water Mix Valve
COMPONENT.
Solenoid Plunger
MATERIAL:
Type 434F Stainless Steel
BAR STOCK:
Coil Stock 0.1195 Inch Round
MACHINE TOOL:
Escomatic
PRIMARY OPERATIONS:
Form, Drill, and Cut-Off
GROSS PRODUCTION:
60 Parts Per Minute
TOLERANCES:
0.001 Inch
FINISH:
40 Micro-Inch
29
1.00
1.00
1.00
1.25
1.00
1.00
1.00
1.00
1.00
1.00
0.08
0.12
0.12
0.12
0.20
0.12
0.12
0.07
0.20
0.025
0.040
0.040
0.040
0.040
0.040
0.040
0.040
0.060
0.040
0.040
0.045
0.040
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.15
0.030
0.030
0.045
0.030
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
Si
23.00/
27.00
18.00/
23.00
17.50/
19.50
11.50/
14.50
10.50/
11.75
14.00/
16.00
16.00/
18.00
16.00/
18.00
15.00/
17.00
16.00/
18.00
16.00/
18.00
17.00/
19.00
Cr
0.50
1.25/
2.50
0.75
0.75
Ni
1.75/
2.50
0.75/
1.25
0.75/
1.25
Mo
80
70
77
77
125
80
70
70
65
60
0.035 N
60
0.2+4(C+N)(min)/
0.80 Ti+Cb
0.25 N
70
5 xC/
0.70 Cb+Ta
0.20+4(C+N)
(min) Ti
0.15 Al
0.10/
0.30 Al
6xC/
0.75 Ti
Other
40
40
45
40
53
53
95
55
40
40
35
25
20
20
25
20
23
23
20
25
20
20
25
20
B95
B90
190
(Brinell)
B83
262
(Brinell)
285
(Brinell)
B83
B75
Sheet
Sheet
Sheet
Elongation
Yield
in 2"
Strength
Hardness Product
Tensile
(Rockwell) Form
(0.2% offset) (50.80mm)
Strength
%, min.
max.
ksi, min.
ksi, min.
c = ASTM A276Condition H.
1.50
1.00
Mn
0.08
446
0.20
(S44600)
405
(40500)
409
(S40900)
429
(S42900)
430
(S43000)
430F
(S43020)
431
(S43100)
434
(S43400)
436
(S43600)
439
(S43900)
(S43035)
442
(S44200)
444
(S44400)
AISI
Type
(UNS No.)
TABLE 5
FERRITIC STAINLESS STEELS CHEMICAL COMPOSITIONS and MECHANICAL PROPERTIES
30
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.27
405
409
429
430
430F
431
434
436
439
442
444
446
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
60
60
64
62
67
60
72
72
59
60
60
Specific
Electrical
Resistance
at 68F
Microhm-Cm
0.11
0.102
0.12
0.11
0.11
0.11
0.11
0.11
0.11
0.11
Specific
Heat
Btu/Lb/F
32-212F
13.8
12.5
15.5
12.1
15.1
11.7
13.8
14.8
13.8
15.6
14.4
Thermal
Conductivity
BTU/ft/hr/F
(68-212F)
5.2
5.6
6.1
5.8
5.8
5.6
5.8
6.0
(6.5)
(68-212F)
5.7
5.8
32-212F
6.0
6.1
6.7
6.1
6.4
(6.6)
(68-500F)
6.1
32-600F
6.2
6.3
6.3
6.7
(6.9)
(68-900F)
6.3
32-1000F
6.4
6.6
6.6
(7.2)
(68-1200F)
6.6
7.5
(7.5)
(68-1500F)
6.9
(32-1500F)
6.9
6.9
(32-1500F)
(6.7)
(32-1800F)
32-1200F 32-1600F
Mean Coefficient of
-6
Notes:
Density
Lb/Cu.In.
Stainless
Steel
Type
Modulus
of
Elasticity
psi
6
x 10
Table 5 Continued
PHYSICAL PROPERTIES OF FERRITIC STAINLESS STEELS
1400-1600
1450-1700
d
1350-1500
1500-1650
1450-1600
1250-1400
d
1150-1225
1400-1600
1450-1550
1250-1400
1350-1500
1625
Magnetic
PermeAnnealing
ability
max.
Temperature
Ferritic stainless steels were once regarded as being difficult to weld.

Weldability, ductility and toughness are improved by reducing carbon
and nitrogen contents, such as in Type 444.
Martensitic Stainless Steels
The martensitic grades are so named because when heated above
their critical temperature (about 1600F) and cooled rapidly, a
metallurgical structure known as martensite is obtained. In the hardened condition, the steel has very high strength and hardness, but to
obtain optimum corrosion resistance, ductility, and impact strength,
the steel is given a stress-relieving or tempering treatment (usually in
the range 300-700F).
Table 6 gives the chemical composition, mechanical and physical
properties of martensitic grades in the annealed and hardened
conditions.
Spindles
PRODUCT:
Direct-Read Water Meters
COMPONENT:
Magnetic Coupling Drive Spindles
MATERIAL:
BAR STOCK:
12 Foot Rod, 0.1562 Inch Diameter .0005

Inch, Ground and Polished, Hardness Rb
88-100
MACHINE TOOL:
#00 Brown and Sharpe Automatic
PRIMARY OPERATIONS:
Form, Knurl, Burnish, Mill, and Cut-Off
GROSS PRODUCTION:
144 Parts Per Hour
CYCLE TIME:
25 Seconds
SFPM:
107
RPM:
About 2000
TOLERANCES:
0.0005 Inch
FINISH:
16 Micro-Inch
31
32
0.040
0.060
0.025
1.00
1.00
1.25
1.00
1.25
0.50/
1.00
0.08
0.15
0.15
Over
0.15
Over
0.15
0.20/
0.25
0.60/
0.75
0.75/
0.95
0.95/
1.20
440A
(S44002)
440B
(S44003)
440C
(S44004)
0.040
0.040
1.00
1.00
0.030
0.030
0.030
0.025
0.15
0.030
0.15
0.030
0.030
0.030
0.030
1.00
1.00
1.00
0.50
1.00
1.00
1.00
1.00
1.00
1.00
0.50
Si
16.00/
18.00
16.00/
18.00
16.00/
18.00
11.50
13.00
11.50/
13.50
11.50/
13.50
11.50/
13.50
12.00/
14.00
12.00/
14.00
12.00/
14.00
11.00/
12.50
Cr
0.50/
1.00
1.25/
2.50
0.60
0.75
Ni
0.75
0.75
0.75
0.90/
1.25
Mo
0.20/
0.30 V
0.90/
1.25 W
Other
110
107
105
140
95
95
75
115
70
c
(120)
70
70
65
62
60
110
55
50
40
90
40
c
(90)
35
40
14
18
20
13
22
25
30
20
20
c
(12)
30
20

Elongation
Yield
in 2"
Strength
Tensile
Strength (0.2% offset) (50.80mm)
%, min.
ksi, min. ksi, min.
269
(Brinell)
269
(Brinell)
269
(Brinell)
298
(Brinell)
262
(Brinell)
241
(Brinell)
262
(Brinell)
d
302-352
(Brinell)
B82
Hardness Product
(Rockwell) Form
max.

0.040
1.00
0.060
0.040
0.040
0.040
1.00
0.15
0.040
1.00
Mn
0.15
403
(S40300)
410
(S41000)
410S
(S41008)
414
(S41400)
416
(S41600)
420
(S42000)
420F
(S42020)
422
(S42200)
AISI
Type
(UNS No.)
TABLE 6
MARTENSITIC STAINLESS STEELS CHEMICAL COMPOSITIONS and MECHANICAL PROPERTIES
33
1800
1800
1800
1900
403
(S40300)
410
(S41000)
416
(S41600)
414
(S41400)
431
(S43100)
Hardening
Temperature F
Types
UNS
440
425
410
410
C45
C44
C43
C43
As Quenched
Hardness
HB
HR
400
600
800*
1000*
1200
400
600
800*
1000*
1200
400
600
800*
1000*
1200
1400
400
600
800*
1000*
1200
1400
Tempering
Temperature F
As Quenched Hardness and Properties After Hardening and Tempering

1 in. (25.4 mm) Diameter Bars
TABLE 6 Continued
TYPICAL MECHANICAL PROPERTIES
205
195
205
150
125
200
190
200
145
120
190
180
195
145
110
90
190
180
195
145
110
90
Tensile
Strength
ksi
155
150
155
130
95
150
145
150
120
105
145
140
150
115
85
60
145
140
150
115
85
60
Yield
Strength
0.2 percent
Offset ksi
15
15
15
18
20
15
15
16
20
20
12
13
13
15
18
25
15
15
17
20
23
30
Elongation
in 2"
(50.80 mm)
Percent
55
55
60
60
60
55
55
58
60
65
45
45
50
50
55
60
55
55
55
65
65
70
Reduction
of Area
Percent
50
30
45
50
45
45
30
60
20
20
75
100
35
35
Izod Impact
V-Notch
Ft.Lbs.
415
400
415
325
260
410
400
415
290
250
390
375
390
300
225
180
390
375
390
300
225
180
C43
C41
C43
C34
C24
C43
C41
C43
C30
C22
C41
C39
C41
C31
B97
B89
C41
C39
C41
C31
B97
B89
Tempered
Hardness
HB
HR
34
1900
1900
1900
1900
420
(S42000)
440A
(S44002)
440B
(S44003)
440C
(S44004)
610
590
570
540
HB
C60
C58
C56
C54
HR
600
600
600
600
Tempering
Temperature F
285
280
260
230
Tensile
Strength
ksi
275
270
240
195
Yield
Strength
0.2 percent
Offset ksi
Elongation
in 2"
(50.80 mm)
Percent
10
15
20
25
Reduction
of Area
Percent
10
Izod Impact
V-Notch
Ft.Lbs.
580
555
510
500
HB
C57
C55
C51
C50
HR
Tempered
Hardness
*Tempering within the range of 750 to 1050F (399 to 565C) is not recommended because such treatment will result in low and erratic impact properties and loss of corrosion resistance.
Note: Variations in chemical composition within the individual type ranges may affect the mechanical properties.
Hardening
Temperature F
Types
UNS
As Quenched
Hardness
As Quenched Hardness and Properties After Hardening and Tempering

1 in. (25.4 mm) Diameter Bars
TABLE 6 Continued
TYPICAL MECHANICAL PROPERTIES
35
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
403
410
410S
414
416
420
420F
422
440A
440B
440C
29.0
29.0
29.0
29.8
29.0
29.0
29.0
29.0
29.0
29.0
29.0
60
60
60
24.3
55
55
57
70
57
57
57
Specific
Electrical
Resistance
at 68F
Microhm-Cm
0.11
0.11
0.11
0.11
0.11
0.11
0.11
0.11
0.11
0.11
0.11
Specific
Heat
Btu/Lb/F
32-212F
14.0
14.0
14.0
13.8
14.5
14.4
14.4
14.4
14.4
14.4
14.4
Thermal
Conductivity
BTU/ft/hr/F
(68-212F)
6.3
6.0
6.1
6.1
6.3
6.3
6.3
32-600F
5.7
(68-392F)
5.7
(68-392F)
5.7
(68-392F)
6.2
5.7
5.7
5.5
5.8
5.5
5.5
5.5
32-212F
32-1200F
6.5
6.6
6.5
6.5
(68-1112F)
6.5
(68-1112F)
6.5
(68-1112F)
6.7
(6.7)
(32-1000F)
6.4
6.5
6.4
(6.4)
6.5
(32-1000F)
6.4
6.5
32-I000F
Mean Coefficient of
-6
Notes:
Density
Lb/Cu.ln.
Stainless
Steel
Type
Modulus
of
Elasticity
psi
6
x 10
Table 6 Continued
PHYSICAL PROPERTIES OF MARTENSITIC STAINLESS STEELS
32-1600F
900
900
900
1550-1650
d
1350-1450
c
1550-1650
d
1350-1450
c
1550-1650
d
1350-1650
1500-1650
d
1200-1400
c
1550-1650
d
1350-1450
c
1550-1650
d
1350-1450
1350-1450
1500-1650
d
1200-1400
c
1500-1650
d
1200-1400
c
1500-1650
d
1200-1400
d
1200-1300
Magnetic
Permeability
Annealing
max.
Temperature
The martensitic stainless steels fall into two main groups that are
associated with two ranges of mechanical properties; low-carbon compositions with a maximum hardness of about Rockwell C45 and the
higher-carbon compositions, which can be hardened to Rockwell C60.
(The maximum hardness of both groups in the annealed condition is
about Rockwell C24.) The dividing line between the two groups is a
carbon content of approximately 0.15 percent.
Low-carbon content is associated with low-chromium content or the
materials will not harden. At higher carbon levels, the chromium content can be raised to about 18 percent. However, because of potential
problems of carbide precipitation (discussed in the section on corrosion) high-chromium martensitic stainless steels are not usually
tempered to the same degree as the low-carbon types.
In the low-carbon class are Types 410, 416 (a free-machining grade)
and 403 (a "turbine-quality" grade). The properties, performance, heat
treatment, and fabrication of these three stainless steels are similar except for the better machinability of Type 416.
On the high-carbon side are Types 440A, B, and C.
Types 420, 414, and 431, however, do not fit into either category.
Type 420 has a minimum carbon content of 0.15 percent and is usually
produced to a carbon specification of 0.3-0.4 percent. While it will not
harden to such high values as the 440 types, it can be tempered without
substantial loss in corrosion resistance. Hence a combination of
hardness and adequate ductility (suitable for cutlery) is attained.
Steam Trap
36
PRODUCT:
Steam Trap
COMPONENT:
Points & Seats
MATERIAL:
BAR STOCK:
5/16
MACHINE TOOL:
Brown & Sharpe Single-Spindle Automatic
PRIMARY OPERATIONS:
Form, Thread, Drill, Burnish, and Cut-Off
SECONDARY OPERATIONS:
Ream and Coin
GROSS PRODUCTION:
180 Parts Per Hour (Primary)
CYCLE TIME:
20 Seconds
SFPM:
100 (5/16 Inch Bar) and 120 (9/16 Inch Bar)
RPM:
1220-850
TOLERANCES:
0.001 Inch
FINISH:
8-16 Micro-Inch
Inch Round and 9/16 Inch Hexagonal, Cold

Rolled and Bright Hardened to Rc 50
Martensitic stainless steels are subject to some temper brittleness

and should not be tempered or used in the range of 800 to 1050F if
optimum toughness is important.
Martensitic grades have a ductile-brittle transition temperature at
which notch ductility drops very suddenly. The transition temperature
is near room temperature, and at low temperatureabout -300Fthey
become very brittle. This effect depends on composition, heat treatment, and other variables.
Clearly, if notch ductility is critical at room temperature or below,
and the steel is to be used in the hardened condition, careful evaluation is required. If the material is to be used much below room
temperature, the chances are that quenched-and-tempered Type 410
will not be satisfactory. While its notch ductility is better in the
annealed condition down to -100F, another type of stainless steel is
probably more appropriate.
The fatigue properties of the martensitic stainless steels depend on
heat treatment and design. A notch, for example, in a structure or the
effect of a corrosive environment can do more to reduce fatigue limit
than alloy content or heat treatment.
Precipitation Hardening Stainless Steels

The principle of precipitation hardening is that a supercooled solid
solution (solution annealed) changes its metallurgical structure on
aging. The principal advantage is that products can be fabricated in
the annealed condition and then strengthened by a relatively lowtemperature 900-1150F aging treatment, minimizing the problems
associated with high-temperature treatments. Strength levels of up to
260 ksi (tensile) can be achievedexceeding even those of the martensitic stainless steelswhile corrosion resistance is usually superior to
that of martensiticsapproximately equal to that of Type 304
stainless. Ductility is similar to corresponding martensitic grades at
the same strength level. Table 7 shows the chemical composition, the
nominal mechanical and physical properties of four AISI
precipitation hardening stainless steels in solution treated and age
hardened conditions.
Production Increased 33 Percent
Tank adaptors, which hold steel tubing in position and house the valves and
quick disconnects on soft drink tanks, were originally made with a foreignproduced Type 304 stainless steel. One problem was excessive downtime due to
the need to remove chips during machining.
A switch to domestically produced Type 304 stainless steel provided
significantly improved machinability, allowing the chips to break up easily. This
enabled the manufacturer to machine the tank adaptors without interruption . . .
thereby increasing production by one-third.
Machining is done on one-inch Acme Gridley Automatic screw machines,
using Type 304 stainless in 11/16-inch and 13/16-inch diameter bars.
37
38
0.07
0.07
0.09
S15500
S17400
S17700
1.00
1.00
1.00
0.10
Mn
0.008
0.040 0.040
0.040 0.030
0.040 0.030
0.010
1.00
1.00
1.00
0.10
Si
16.00/
18.00
15.00/
17.50
14.00/
15.50
12.25/
13.25
Cr
6.50/
7.75
3.00/
5.00
3.50/
5.50
7.50/
8.50
Ni
2.00/
2.50
Mo
0.75/
1.50 Al
3.00/
5.00 Cu
0.15/
0.45 Cb+Ta
2.50/
4.50 Cu
0.15/
0.45 Cb+Ta
0.90/
1.35 Al
0.010 N
Other
150
160
160
160
65
145
145
120
25
15
15
17
Elongation
Yield
in 2"
Strength
Tensile
Strength (0.2% offset) (50.80mm)
%, min.
ksi, min. ksi, min.
B100(min)
C38
C38
C38
Hardness
(Rockwell)
max.
Sheet
Product
Form
0.05
S13800
AISI
Type
(UNS No.)
TABLE 7
PRECIPITATION HARDENING STAINLESS STEELS CHEMICAL
COMPOSITIONS and MECHANICAL PROPERTIES
39
0.28
0.28
0.28
0.28
S13800
f
S15500
f
S17400
g
S17700
29.4
28.5
28.5
29.5
102
77
80
83
Specific
Electrical
Resistance
at 68F
Microhm-Cm
0.11
0.10
0.11
0.11
Specific
Heat
Btu/Lb/F
32-212F
8.1
10.3
10.6
9.5
Thermal
Conductivity
BTU/ft/hr/F
(68-212F)
5.9
6.0
6.0
(8.6)
(68-200F)
32-212F
6.2
6.3
6.4
(9.7)
(68-600F)
6.6
32-600F 32-1000F
32-1200F
Mean Coefficient of
-6
Notes:
Density
Lb/Cu.In.
Stainless
Steel
Type
Modulus
of
Elasticity
psi
6
x 10
Table 7 Continued
PHYSICAL PROPERTIES OF PRECIPITATION HARDENING STAINLESS STEELS
32-1600F
Magnetic
Permeability
max.
Annealing
Temperature
Precipitation hardening stainless steels have high strength, relatively

good ductility, and good corrosion resistance at elevated temperatures.
They are utilized for aerospace structural components, fuel tanks, landing gear covers, pump parts, shafting, bolts, saws, knives, and flexible
bellows-type expansion joints.
HIGH-TEMPERATURE MECHANICAL PROPERTIES

Stainless steels are used at temperatures up to about 2000F because
they have good strength at elevated temperature and good resistance to
corrosion and oxidation.
In steam power generation, for example, high allowable design
stresses permit the use of thin sections and high operating temperatures.
In aircraft and spacecraft design, the AISI numbered stainless steels are
used for parts in which hot strength is crucial. Stainless steels are used
extensively in heat exchangers in which there is need for both corrosion
resistance and hot strength, especially for pressure service. In the
nuclear power industry, there are high temperature applications for
stainless steels in superheaters, boilers, feedwater heaters, valves, and
main steam lines.
In analyzing high-temperature properties, hot strength and thermal
stability (from the standpoint of softening or embrittlement) are important. Physical properties are also significant.
Figure 5 gives a broad concept of the hot-strength advantages of
stainless steels in comparison to low-carbon unalloyed steel. Precipitation hardening stainless steels also have excellent hot strength at
moderate temperatures, but their strength declines sharply as they
overage at high temperature.
Thermal Stability
With time and temperature, changes in metallurgical structure can be
expected for almost any steel or alloy. In stainless steels, the changes
can be softening, carbide precipitation, or embrittlement.
Softening occurs in the martensitic stainless steels when exposed to
temperatures approaching or exceeding the original tempering
temperature. Type 440C, for example, can be held at 900F for only
short periods if the high hardness is to be retained. Cold-worked
austenitic stainless steels may also soften at elevated temperature.
Embrittlement usually means the loss of room-temperature
toughness. Embrittled equipment must be handled carefully to avoid
impact when it is cooled down for maintenance. Embrittlement is rarely
of concern with austenitic stainless steels.
Ferritic stainless steels are subject to embrittlement when exposed to
temperatures of 700-950F over an extended period of time. Martensitic
grades with 12 percent chromium also have been known to display
brittle tendencies after extended periods in the same temperature range.
This phenomenon is called 885F embrittlement because of the
temperature at which embrittlement is most pronounced.
40
Figure 5
HOT-STRENGTH CHARACTERISTICS
General comparison of the hot-strength characteristics of austenitic, martensitic and

ferritic stainless steels with those of low carbon unalloyed steel and semi-austenitic
precipitation and transformation-hardening steels.
41
885F embrittlement results in low ductility and increased hardness

and tensile strengths at room temperature, and the metal may fracture if
not handled carefully. The metal, however, retains its desirable
mechanical properties at operating temperature (500F and higher). The
effect of 885F embrittlement can be removed by heat treatment at
1100F followed by air cooling.
Brittle failure under load is of concern, especially in welded fabrications. This type of embrittlement is largely a problem at temperatures
of 1000-1500F, since strength and not ductility is the limiting factor at
higher temperatures. Because of difficulty in evaluating data, and the
variable conditions involved, designers are encouraged to seek
technical assistance from stainless steel producers (listed on back
cover).
LOW-TEMPERATURE MECHANICAL PROPERTIES

Alloys for low-temperature service must have suitable engineering
properties, such as yield and tensile strengths and ductility. Experience
with brittle fracture of steel ships during World War II demonstrated
that many metals may have satisfactory "room-temperature"
characteristics but not perform adequately at low temperatures. Lowtemperature brittle fracture can occur, sometimes with catastrophic
failure, without any warning by stretching, sagging, bulging, or other
indication of plastic failure. Alloys that are ordinarily ductile may suddenly fail at very low levels of stress.
In the handling and storage of liquid gases at cryogenic temperatures,
few steels can be used. Austenitic stainless steels are among these few
because they exhibit good ductility and toughness at the most severe of
cryogenic temperaturesminus 423F.
Table 8 shows tensile properties of several stainless steels at
cryogenic temperatures. Austenitic grades show not only good ductility
down to -423F, but they also show an increase in tensile and yield
strengths.
Toughness is also excellent as indicated by the impact strength
valuesalthough there is some decrease as temperature decreases.
Switching Nets
Lower Manufacturing Costs
A screw machine shop making fittings for energy related equipment, experienced
many machining problems with imported Type 316 stainless steel bars. Inconsistent
size and chemistry resulted in a high rate of snapped taps, and an upturn in
downtime.
The switch to domestically produced Type 316 stainless steel produced
immediate results. Machining time was cut by 3.8 seconds per piece, a 20 percent
saving of time. Overall tap life was increased by 50 percent through more consistent
machinability.
The Type 316, in -inch rounds, is run on a Wickman six-spindle automatic
screw machine with a basic production sequence that includes center drilling, two
tap drills, tap and small-hole drilling with a speeder. Critical dimensions for the fitting include an end pipe thread truncation with a maximum limit of 0.005 inch.
42
Table 8
TYPICAL MECHANICAL PROPERTIES OF STAINLESS
STEELS AT CRYOGENIC TEMPERATURES
Type
304
310
316
347
410
430
Yield
Strength
Test
Temperature 0.2% Offset
F
ksi
- 40
- 80
-320
-423
- 40
- 80
-320
-423
- 40
- 80
-320
-423
- 40
- 80
-320
-423
- 40
- 80
-320
- 40
- 80
-320
34
34
39
50
39
40
74
108
41
44
75
84
44
45
47
55
90
94
148
41
44
87
Tensile
Strength
ksi
Elonga
tion in
2"
%
155
170
221
243
95
100
152
176
104
118
185
210
117
130
200
228
122
128
158
76
81
92
47
39
40
40
57
55
54
56
59
57
59
52
63
57
43
39
23
22
10
36
36
2
Izod Impact
ft. lbs.
110
110
110
110
110
110
85
110
110
110
110
95
60
25
25
5
10
8
2
Auto Emission Parts With 303

Control valve parts for automotive emission systems require machining of three
different angles, with a tolerance of 6 minutes, a drilling operation, and a microinch finish of 16 or better.
Using Type 303 stainless steel, the manufacturer achieves consistent
machinability, close tolerances, low tool breakage, few rejects and excellent surface
finisheswithout the need for grinding and polishing. Downtime is low, operating
efficiency is high and profitability is good.
43
THE MACHINABLE FAMILY

OF STAINLESS STEELS
What is machinability?
Machine shop operators have differing opinions as to what
machinability really is. Some are interested only in the speed at which
a material can be cut, others consider tool life at a reasonable speed to
be most important, while others rate machinability on the surface
finish produced. Obviously, all factors are importantcutting speed,
tool life, and surface finishand all are considered in rating the
machinability of a metal.
The machinability of stainless steels is substantially different from
that of carbon or alloy steels and other metals, as illustrated in the
chart, "Comparative Machinability of Common Metals" (Figure 6). In
varying degrees, most stainless steels are tough, rather gummy, and
they tend to seize and gall.
Figure 6
COMPARATIVE MACHINABILITY
OF COMMON METALS
44
The 400 series stainless steels are the easiest to machine, but they
do produce a stringy chip that can slow productivity. The 200 and
300 Series, on the other hand, are characterized as being the most
difficult to machine, primarily because of their gumminess and,
secondarily, because of their propensity to work harden at a very
rapid rate. However, the difficulty is not so great as to be a deterrent
to selecting a stainless steel for a machined part.
In fact, stainless steels are routinely machined on high-production
equipment as demonstrated by the illustrations in this booklet. The
best way to get maximum machinability, wherever end-use
conditions permit, is to specify a free-machining stainless steel.
Air Valve
PRODUCT:
Solvent Spray Gun
COMPONENT:
Air Valve Seat
MATERIAL:
BAR STOCK:
0.687 Inch (0.002 Inch) Round, Annealed,

Centerless Ground
MACHINE TOOL:
Acme Six-Spindle Bar Machine
PRIMARY OPERATIONS:
Form, Center Drill, Roll Thread, Form, Drill,

and Cut-Off
Countersink, Thread, Cross Drill, Mill,

Deburr, and Electropolish
GROSS PRODUCTION:
96 Parts Per Hour
CYCLE TIME:
38 Seconds
SFPM:
120
RPM:
617
TOLERANCES:
0.005 Inch
FINISH:
250 Micro-Inch
45
FREE-MACHINING STAINLESS STEELS

Certain alloying elements in stainless steels, such as sulfur, selenium,
lead, copper, aluminum, or phosphorus can be added or adjusted during
melting to alter the machining characteristics. These alloying elements
serve to reduce the friction between the work-piece and the tool thereby
minimizing the tendency of the chip to weld to the tool. Also, sulfur
forms inclusions that reduce the friction forces and transverse ductility
of the chips, causing them to break off more readily. The improvement
in machinability in the free-machining stainless steelsnamely Types
303, 303 Se, 430F, 416, and 420Fis clearly evident in the chart,
"Comparative Machinability of Frequently Used Stainless Steels"
(Figure 7).
Figure 7
COMPARATIVE MACHINABILITY OF
FREQUENTLY USED STAINLESS STEELS
AND THEIR FREE-MACHINING COUNTERPARTS
% based on 100% for AN Type 416 free-machining Stainless Steel

It has been traditional in machining literature to compare the machinability of
various metals to AISIB-1112 which is a free-machining carbon steel. However,
since Type 416 stainless steel has a machining rating equal to that of B-1112, and
since B-1112 is no longer on the market, comparisons in this booklet will be made
with Type 416 as the base at 100%.
46
Should a designer select Type 304 on the basis of corrosion

resistance and strength but recognizes a need for the best possible
machining rate, he may elect to use free-machining Type 303. The
chromium, nickel, and sulfur contents of Type 303 are slightly different
than that of Type 304, but its physical and mechanical properties are
quite similar. Type 303 can be machined at speeds about 25-30 percent
faster than Type 304.
Type 303 Se is a free-machining variation of Type 304 that contains
selenium instead of sulfur. Type 303 Se is a better choice than Type
303 when a better machined surface finish is required or when cold
working may be involved, such as staking, swaging, spinning, or severe
thread rolling, in addition to machining.
There are also free-machining alternatives to consider in the 400
series stainless steels. For instance, if end-use conditions call for Type
430 stainless, the specifier might select Type 430F. The composition of
Type 430F is adjusted to enhance the machining characteristics while
preserving as best possible the qualities of Type 430.
The free-machining variation of Type 410 is Type 416, and for Type
420, the specifier should consider Type 420F (Detailed descriptions of
the free-machining stainless steels begin on page 60.)
Specifiers should recognize that the alloying elements used to
improve free-machining characteristics adversely affect corrosion
resistance, transverse ductility, and other qualities, such as weldability.
However, the free-machining grades are often specified after evaluation
as to their suitability for the intended corrosive environment in which
they will serve. When they are specified, however, significantly higher
production rates can be achieved.
There are other alternatives specifiers should consider, especially if
there is concern over the use of a free-machining stainless steel. For
example, composition of a stainless steel is often altered slightly by the
producer to enhance certain fabrication characteristics, including
machinability, but without changing other basic qualities. While the
improvement may not be as great as with a "true' free-machining type,
there is improvement.
Also, producers of stainless steel bar can provide a product that is in
the best condition for machining. However, as experienced machinists
know, the best condition for turning may not be the best condition for
drilling, so specifiers are encouraged to discuss the machining application with a producer.
Type 303 a "Cut Above"

Electronic surgical blades made of Type 303 stainless steel resist corrosion from
atmospheric sources and sterilizing solutions. Disposable electronic surgical blades,
fabricated from coils of 0.093/0.094-inch round stock in the annealed, cold drawn
condition, are machined on precision coil fed automatics. With carbide tooling and
sulfo-chlorinated cutting fluid, cycle time is eight seconds per part.
47
BUY A BETTER BAR

Among the various considerations for better machining efficiency in
stainless steels are the purchase details of the basic bar stock. Discussed
previously were the various conditions in which stainless steels are
availableas free-machining types, as special analyses suitable for
machining, and condition.
There is another aspect worth consideration that falls more in the
realm of purchasing than design, but alert engineers do not want to
overlook any angle to minimize costs.
Bar for machining is available in more than just a length of metal for
the shop to cut up on a machine tool. Basic shapes, such as rounds,
squares, hexagonals, and octagonals have always been available. It
stands to reason that the closer you can come to the final shape in the
starting bar material, the less machining will have to be performed.
Some forward looking domestic bar producers have carried the shape
concept a number of steps forward by producing special shapes, the
catch-word for which is "near net shape." Special shapes, such as
illustrated in Figure 8, are hot rolled, cold drawn, or extruded. They are
worthy of consideration because of the potential for reduced machining
and handling.
Figure 8
48
Other considerations for reduced machining are forgings or tubular

products. Seamless or welded mechanical tubing is readily available in
a broad range of compositions (carbon, alloy, and stainless steels), sizes
and wall thicknessesand shapes. Mechanical tubing for machining is
often referred to as hollow bar.
Hollow bar is especially attractive for projects that require 30 percent or more metal removal from the center. Not only does hollow bar
generally cost less per foot than solid bar of equal diameter (less cost
because less weight), but it will require less machining, produce less
scrap, improve cycle time, and allow more parts to be produced per
hour.
Mechanical tubing is usually available from 1-inch diameter with
about a 0.125-inch wall thickness, up to a 5-inch diameter tubing with
about a 3-inch wall. Check with suppliers for availability of sizes and
shapes.
Rod and wire in coiled form are also available for coil-fed screw
machines. Table 9 describes the conditions and finishes in which
stainless steel bars are normally available.
Table 9
CONDITIONS & FINISHES FOR BAR
Conditions
Surface Finishes*
1. Hot worked only
(a) Scale not removed (excluding spot conditioning)

(b) Rough turned**
(c) Pickled or blast cleaned and pickled
2. Annealed or otherwise
heat treated
(a) Scale not removed (excluding spot conditioning)

(b) Rough turned
(c) Pickled or blast cleaned and pickled
(d) Cold drawn or cold rolled
(e) Centerless ground
(f) Polished
3. Annealed and cold

worked to high
tensile strength* * *
(d) Cold drawn or cold rolled

(e) Centerless ground
(f) Polished
*Surface finishes (b), (e) and (f) are applicable to round bars only.
**Bars of the 4xx series stainless steels which are highly hardenable, such as Types
414, 420, 420F, 431, 440A, 440B and 440C, are annealed before rough turning. Other
hardenable grades, such as Types 403, 410 and 416, may also require annealing
depending on their composition and size.
***Produced in Types 302, 303Se, 304 and 316.
49
STAINLESS STEELS FOR SCREW MACHINE OPERATIONS

Higher production rates are not the only benefits derived from the
free-machining stainless steels. As shops become better acquainted
with machining stainless steels they acquire confidence to use screw
machines for increased productivity. This can be particularly important because many parts are being machined at higher cost than would
be required to produce those same parts on automatic screw machines.
Low productivity can exist when the production department
underestimates the practicality and feasibility of stainless steels for
screw machine production. This situation will change as they become
aware of the extreme versatility of the several types of automatic
screw machines in use, and of the extreme versatility in stainless steel
selection.
If the part meets the following six criteria, screw machining should
be seriously considered for stainless steel:
1. The part to be produced should be in lots of 1,000 or more.
This is more a function of time than number, however, and
production runs should be at least as long as the set-up time.
2. Tolerances, in general, should be in the range of .001 inch.
3. The part has to be made from rod, bar, tubing, or hollow bar.
4. Turned or formed finishes in the range of 16 to 125 RMS
should be acceptable.
5. Overall diameter of cross-section dimension should be between
1/64 inch and 8 inches.
6. Overall length of machined part is usually less than 10 stock
diameters.
PH Packing Nuts
Packing nuts for instrumentation valves are used in natural gas process lines, which
are exposed to a variety of corrosive chemicals at temperatures from -65F to +450F
and pressures to 5000 psi. This requires the strength of Type 416 but with better
corrosion resistance.
S45000 (UNS) martensitic, precipitation hardenable stainless steel combines the
strength of Type 416 with the corrosion resistance of Type 304. Also, since the packing
nut mates with Type 316, the choice of S45000 minimizes seizing and galling
tendencies.
Packing nuts have dual threads; external threads for attaching to the valve housing
and internal threads for operation of the valve stem.
The precipitation hardening stainless, which has a yield strength of 95, 000 psi
(minimum) in the annealed condition, is machined like other martensitic stainless steels.
Starting with 5/8 inch hexagonal, cold-drawn bars, the packing nuts are made on Greenlee
Automatic Screw machines, and Reed Thread Rolling machines.
50
MACHINABILITY VS. COST

Many factors influence the ratio of machinability to cost of screw
machine products, including the choice of materials. Experience has
clearly established that the "cheapest" material does not always yield
the lowest cost. Metals having low machinability ratings require more
frequent tool changing, longer downtime, and greater difficulty in
maintaining good finish. This is particularly true when stainless steels
are involved; machining costs tend to increase as machinability
decreases. Accordingly, a stainless steel with improved machining
characteristics is to be preferred. Even if there is a slight premium in
the cost of such bar stock, it is generally more than offset by the resultant ease of machining.
When material specifications permit, it is to everyone's advantage to
give the screw machine shop the opportunity to use a free-machining
material.
Other Factors Affecting Cost

In addition to material selection, other considerations contribute to
the machinability/cost ratio. When two or more types of machines can
produce acceptable parts, cost per piece usually determines the final
choice. Machining cost per piece is influenced most by cost of setup,
cost of labor and burden (amortization) of machine tools. Experienced
screw machine shops are more than qualified to determine the type of
machine that will produce the part with the greatest degree of
economy and dispatch.
Another factor affecting cost is brought to bear long before the
order is placed for machining. This factor comes into play on the
designer's drawing board. If screw machine parts are overdesigned and
overspecified, machining expense will increase unnecessarily,
especially on long production runs. The following several pages have
been devoted to parts design hints to assist the design engineer in
achieving the ultimate economy.
In the final analysis, the best way to control the machinability/cost
ratio of any screw machine parts is to discuss every detail with the
production engineer, to take advantage of his knowledge and experience in advance of actual production.
Tough Parts Made Easy
Precision screw machine components for military communications equipment have
to be extremely reliable, possessing both strength and corrosion resistance. Freemachining Type 303 does both, and it minimizes tool breakage and machine downtime.
A change from a high manganese stainless steel to Type 303 also resulted in more
uniform machinability.
The shafts, screw assemblies, spacers, bushings, rivets, washers, and supports are
fabricated on high speed Davenport and Swiss automatic screw machines.
51
DESIGN HINTS FOR

SCREW MACHINE PARTS
Remove All Burrs
Such common notations as "Remove all burrs" are more often than
not indicated as a matter of course on drawings, even when they are
totally unnecessary. To avoid excessive machining expense, unnecessary notations should be omitted from specifications whenever
possible. Burr removal should be specified only where needed, such as
shown below.
Tolerances
To the machine shop, this type of notation means all dimensions of
the part are to be held to .005" (.127mm). The part is thus estimated
and produced at an unnecessarily inflated cost. Tolerances should be
tight only where they are required for satisfactory function.
52
Sharp Corners
A sharp corner may require extra machining so it should be
specified only when necessary. If an inside or outside edge requires
a break only, this should be specifically stated, leaving the radius or
angle of the break to the discretion of production.
Concentricity
Concentricity of drilled holes to diameter can be held to 0.002 " TIR
or better on some parts, but more liberal tolerances can reduce final
costs significantly. Allowable eccentricity should be clearly stated on
the specification.
Center Hole
If a screw machined part is to be held between lathe centers for further machining, holes must be provided for this purpose. A center
hole is easily machined in the outer end of a part but at the rear of the
part it is more difficult and costly. Specifications for such rear center
holes are often left on drawings when they are not needed; an
expensive oversight. The same is true of a 30 degree chamfer on the
outer end of a hole.
53
Slots
Attachments generally utilize circular milling cutters for slot cutting.
This means that the radius produced at the bottom of a slot will correspond to the radius of the cutter used for this operation. A flatbottomed slot can be cut, but at added expense. If the slot is specified
for driving purposes, the drawing should indicate a bottom with an
optional radius. Tooling for straddle milling is similar to that required
for slotting. Whenever a radius is allowable at the junction of a milled
or round area, the drawing should so state.
Heat Treating
If heat treating can be expected to affect the concentricity of a
machined part, allowances for this possibility should be taken into
consideration when drawing machining specifications.
If a part is to be plated, plating thickness and tolerance must be
indicated on the drawing.
54
Finishes
It is important that drawings show whether finishes are for function
or appearance, whether tool marks are allowable, and whether
waviness or lay are critical. The drawing submitted is the final
authority on such details and should be so constructed.
Secondary Operations
As a rule, the most economical product is made in one operation
with no secondary work required on other equipment. Because
secondary operations are less automated, they are often more costly
than making the part in bland form on a screw machine.
There are exceptions to this rule, however, and the comparative
illustration below is an example. The drastic reduction of material in
the stem area of the part marked "A" created a heat problem, which
lowered tool life and caused cracks in the finished part. By redesigning
the part to be made in two pieces, as shown in the drawing marked
"B", total cost of machining and joining the two components reduced
the cost about 25 percent, and resulted in a better product.
55
Shape and Orientation

When the parts designer regards function his prime objective, he
can sometimes reduce costs even when tolerances cannot be changed.
The next example illustrates this point.
The shape of the valve seat shown in drawing A, combined with
tolerances called for on the flat face, made a secondary operation
necessary. The part was screw machined, rounded end out, then
placed on a bench lathe to complete facing of the valve seat to the
required flatness.
Since the rounded nose of the part served no function, the drawing
was revised to allow the part to be made with the seat end out (drawing B), thus eliminating the secondary operation. The result: a 30 percent saving in material and a 55 percent reduction in overall cost.
Uniformity Helps
Producing terminal connection inserts of Type 303 includes an unusual configuration of a thin wall with threads on both inside and out. Nevertheless, machining on
Acme Gridley 8-spindle automatics is accomplished with few rejects and minimum
downtime.
56
No-Frills Please
Here is another example where unnecessary design frills were eliminated to
reduce part costs by a considerable margin.
Both parts shown here serve the same function. The one on the top includes
an unnecessary hole in the rivet end of the shank, and a 3/16-inch radius on the
head end which serves no specific purpose.
A change in material specificationplus redesign to eliminate the unnecessary
hole and replace the 3/16-inch radius with an adequate corner breakcreated a
part that provided the same function as the original part, at a cost saving of 37
percent.
57
GOOD SHOP PRACTICES

Of course, a good deal of success in machining and reducing production costs rests with the machine shop. Here are a few guidelines that
may be useful when working with stainless steels:
1. Machine tools should be rigid, modern, and as much "overpowered"
as possible. Best practice is to use the machine up to about 75
percent of its rated capacity.
2. The work-piece and tool should be held rigid. Tool overhang should
be minimized and extra support used when necessary.
3. Tools, either high speed tool steels or carbide, should be kept sharp,
preferably being sharpened at regular intervals rather than only when
necessary.
4. A good lubricant is required, such as compounded sulfurchlorinated
mineral oil plus fatty oil for high-speed tools, and heavy duty
emulsifiable oil for carbide tools.
5. Positive cuts are necessary. Care should be exercised to avoid
dwelling so as not to work harden the material, especially the
austenitic (300 Series) stainless steels.
d/p Cell
58
PRODUCT:
Electronic Differential Pressure Cell
COMPONENT:
Cap-End Spacer
MATERIAL:
BAR STOCK:
1 Inch Round, Cold Rolled, Annealed,

Ground, Hardness Rb 95 (Maximum)
MACHINE TOOL:
Warner & Swasey Five-Spindle Bar Machine
PRIMARY OPERATIONS:
Turn, Drill, Form, Knurl, Ream, Tap, and CutOff
Thread, Contour, Cross-Drill
GROSS PRODUCTION:
54 Parts Per Hour
CYCLE TIME:
59 Seconds
SFPM:
90
RPM:
272
TOLERANCES:
0.0015 Inch
FINISH:
63 Micro-Inch
CLEANING AND PASSIVATING

Chemical cleaning is also important for the removal of "free-iron"
from the machined surface. During machining, the stainless steel part
can pick up minute particles of iron, which if not removed can form
rust spots on the surface. These rust areas, which result from the cutting toolnot the stainless steel itselfcan be prevented by immersing
the finished part in a chemical solution. Chemical cleaning is
sometimes used interchangeably with passivation, which is another
method for removing contamination from the metal surface. Properly
cleaned stainless steel will passivate in contact with air, but for much
better corrosion resistance, passivation should be done in appropriate
solutions. For passivation procedures, it is best to consult technical
literature available from stainless steel producers.
For the stainless steel part to achieve maximum corrosion resistance,
it should be cleaned to remove grease, oil, and fingerprints from the
surface. The average shop degreasing solution is usually sufficient. If
not, the final chemical cleaning (passivating) solution can leave a
tightly adhering brown stain on the metal surface.
Pilot Valve
PRODUCT:
Air Valve
COMPONENT.
Pilot Valve Plunger
MATERIAL:
BAR STOCK:
0.500 Inch Bar, Annealed and Centerless

Ground
MACHINE TOOL:
Acme 6-Spindle Bar Machine
PRIMARY OPERATIONS:
Form, Drill, Tap, and Cut-Off
Drill, Form, Tap, and Broach
GROSS PRODUCTION:
133 Parts Per Hour
CYCLE TIME:
27 Seconds Per Part
SFPM:
105
RPM:
824
TOLERANCES:
0.001 Inch
FINISH:
32 Micro-Inch
59
THE FREE-MACHINING
STAINLESS STEELS
TYPES 303 AND 303 Se STAINLESS STEELS
CHEMICAL
COMPOSITION, Percent
303
303 Se
Carbon ........................................
0.15 Max.
0.15 Max.
Manganese .................................. 2.00 Max.
2.00 Max.
Phosphorus .................................. 0.20 Max.
0.20 Max.
Sulfur ....................................... 0.15 Min.
0.060 Max.
Silicon ......................................... 1.00 Max.
1.00 Max.
Chromium ................................... 17.00/19.00
17.00/19.00
Nickel....................................... 8.00/10.00
8.00/10.00
Selenium .....................................
0.15 Min.
Molybdenum ................................... 0.60 Max. (Optional)
DESCRIPTION
Types 303 and 303 Se stainless steels are the free-machining variations of Type 304 (austenitic-l8Cr-8Ni) that are particularly well
suited for screw machining operations. Their greatest benefit is higher
productivity resulting from longer tool life and higher cutting speeds
in comparison to Type 304.
Type 303 has wide application for shafting, valve bodies, valves,
valve trim, fittings, etc. This stainless steel has desirable nongalling
properties that make disassembly of parts easyand help to prevent
scratching or galling in moving parts.
Type 303 Se has applications similar to Type 303 except that it has
slightly better corrosion resistance than Type 303 and better
formability for applications involving hot or cold working operations.
MACHINING CHARACTERISTICS
Types 303 and 303 Se stainless steels machine easily with a brittle
chip. In turning operations they can be used at speeds of 102-130 surface feet per minute. Moderate cold working increases the machinability. Grinding and polishing operations can be very satisfactorily
performed. In comparison to Type 416, their machinability rating
average is 75 percent.
60
Types 303 and 303 Se stainless steels resist rusting from all normal
atmospheric sources and are used in connection with sterilizing solutions, most of the organic chemicals and dyestuffs, and a wide variety
of inorganic chemicals. They resist nitric acid well, the halogen acids
poorly, and the sulfuric acids moderately.
For optimum corrosion resistance, all parts made of Types 303 or
303 Se should be entirely free from scale and foreign particles, such as
iron particles picked up from tooling. It is suggested that after
machining, all parts be cleaned and passivated. Also, if during
fabrication, components are heated and cooled in the range of 8001650F a corrective thermal treatment is suggested to avoid chances of
intergranular corrosion. Such a treatment consists of heating to about
1900F followed by quenching in water.
PHYSICAL PROPERTIES
Specific gravity ...................................................................................................
3
Density-lb/in .......................................................................................................
Mean coefficient of thermal expansion
-6
in/in/F x 10 (32-1200F) ......................................................................
-6
mm/mm/C x 10 (0-649C) ...................................................................
Electrical resistivity
ohm-cir mil/ft ........................................................................................
microhm-cm ..........................................................................................
Specific heat
Btu/Ib/F(32-212F) ...............................................................................
J/kg K (0-100C) ..................................................................................
8.00
0.29
10.4
18.7
433
72
0.12
502
MECHANICAL PROPERTIES (Typical)

Test for 1 " (25.4 mm) Round Bar
Annealed &
Annealed Cold Drawn
Yield Strength 0.2% offset
ksi .............................................
MPa ..........................................
Tensile Strength
ksi .............................................
MPa ..........................................
Elongation in 2" (50.8mm), % ........................
Reduction of area % ...............................
Brinell hardness .................................
Impact resistance, Izod
ft-lb ..........................................
Joules........................................
35
241
60
414
85
621
50
55
160
100
689
40
53
228
80
108
THERMAL TREATMENT
Initial forging temperature .................................................2100-2350F (1149-1288C)
Annealing temperature .......................................................1850-2050F (1010-1121C)
Followed by rapid cooling
Hardening
Cannot be hardened by heat treatment. Upon being cold worked, Types 303 and
303 Se stainless steel increase in strength and hardness.
61

CHEMICAL
Carbon ...........................................................................................................
Manganese .....................................................................................................
Phosphorus ....................................................................................................
Sulfur .............................................................................................................
Silicon ............................................................................................................
Chromium ......................................................................................................
Selenium ........................................................................................................
Molybdenum ..................................................................................................
430F
0.12 Max.
1.25 Max.
0.060 Max.
0.15 Min.
1.00 Max.
16.00/18.00
0.60 Max. (Optional)
DESCRIPTION
Type 430F stainless steel is suggested for faster cutting and reduced
costs when making machined parts from a 16.00/18.00 percent
straight-chromium stainless steel. It machines in turning operations at
speeds of 124-155 surface feet per minute or at about the same as ASE
1120, 1030, etc. Type 430F does not harden by heat treatment. It is
used for parts requiring good corrosion resistance, such as solenoid
valves, aircraft parts, gears, etc. Type 430F is not usually recommended for vessels containing gases or liquids under high pressure.
Type 430F stainless steel is used to combat corrosion from atmosphere, fresh water, nitric acid, dairy products, etc. Parts must be
entirely free from scale and foreign particles. As a final treatment,
after the scale has been removed or after machining, all parts should
be passivated.
PHYSICAL PROPERTIES
Specific gravity ...............................................................................................
3
Densitylb/in .................................................................................................
-6
in/in/F x 10 (32-1200F) ........................................................................
-6
mm/mm/C x 10 (0-649C) ....................................................................
ohm-cir mil/ft .........................................................................................
microhm-cm ...........................................................................................
Specific heat
Btu/lb/F (32-212F) ...............................................................................
J/kg K ...................................................................................................
62
7.75
0.28
6.6
11.9
361
60
0.11
460

Annealed &
Annealed Cold Drawn
ksi .........................................
MPa ..........................................
Tensile Strength
ksi .........................................
MPa ..........................................
Elongation in 2" (50.8mm), % ........................
Reduction of area % ................................
Brinell hardness ..................................
55
379
80
552
80
552
25
60
170
90
621
15
55
190
THERMAL TREATMENT
Initial forging temperature ............................................... 1950-2100F (1066-1149C)
Annealing temperature ..................................................... 1250-1400F (677-760C)
Hardening
Not appreciably hardenable by thermal heat treatment, but can be slightly
hardened by cold working.
The Ultimate in Cylinder Rods

While other manufacturers use chrome-plated carbon steel for air cylinder piston
rods, this company uses Type 416 stainless steel because it provides the corrosion
resistance necessary to help maintain a uniformly smooth surface on the piston rod.
This, in turn, reduces wear on the "O" ring seal, assuring a tight seal for the life of the
cylinder.
Machining operations for the piston rods are critical, especially in the final stage of
fabrication. The manufacturer requires consistently uniform threads that cannot rip the
"O" ring when assembled. Since threading is one of the last steps in fabricating, the
success of the part hinges on this operation.
Type 416 is supplied as precision ground and polished rounds in diameters ranging
from 5/16 inch to 1- inches. The material is machined on Brown and Sharpe singlespindle automatics. The fabrication sequence includes box turning, machining of piston
diameter, cutting grooves in the piston, cutting thread diameters, cutoff and end
chamfering. Secondary operations include threading one end of the rod, then broaching.
63

CHEMICAL
Carbon...........................................
Manganese .......................................
Phosphorus .......................................
Sulfur.............................................
Silicon ...........................................
Chromium .........................................
Selenium ...........................................
Molybdenum .....................................
416
0.15 Max.
1.25 Max.
0.060 Max.
0.15 Min.
1.00 Max.
12.00/14.00
0.60 Max. (Optional)
DESCRIPTION
Type 416 is the most readily machinable of all stainless steels, and it
is particularly well suited for good productivity on automatic screw
machining operations because of the longer tool life that results. The
uses for Type 416 are extensive and include fittings, gears, housings,
lead screws, shafts, valve bodies, valve stems, and valve trim. In fact,
this type is ideal for parts requiring considerable machining work. Its
low frictional properties minimize galling in service. Threaded sections
work freely without seizing, and disassembly is particularly easy.
Pump shafts and valve stems work more smoothly in packing, and
many metal-to-metal contacts withstand more pressure because of their
anti-seizing characteristics.
Type 416 stainless steel cuts very freely because of the sulfur content. In automatic screw machines Type 416 machines at about 165
surface feet per minute.
While not as corrosion resistant as an austenitic (300 series type) or
Type 430F, Type 416 resists atmospheric environments, fresh water,
mine water, steam, carbonic acid, gasoline, crude oil, blood, perspiration, alcohol, ammonia, soap, sugar solutions, etc. A high finish is
helpful in providing optimum resistance to corrosion. It also resists
scaling at elevated temperatures and can be used for continuous service up to about 1200F (Maximum corrosion resistance is achieved in
the heat treated condition.)
64
PHYSICAL PROPERTIES
Specific gravity ..................................................
3
Density-lb/in ..................................................
-6
in/in/F x 10 (32-1200F) .......................................
-6
mm/mm/C x 10 ...........................................
ohm-cir mil/ft..................................................
microhm-cm ...................................................
Specific heat
Btu/lb/F (32-212F) .............................................
J/kg K ....................................................
7.75
0.28
6.5
11.7
343
57
0.11
460

Test for 1 "(25.4 mm) Round Bar
Annealed
ksi............................................
MPa.........................................
Tensile Strength
ksi ...........................................
MPa.........................................
Elongation in 2 " (50.8mm) % ..........................
Reduction of area % ..............................
Brinell hardness ..................................
Impact resistance, Izod
ft-lb .........................................
Joules ......................................
Tempered &
Cold Drawn
40
276
85
586
75
517
30
60
155
100
689
13
50
205
70
95
20
27
THERMAL TREATMENT
Initial forging temperature ............................................... 21002300F (11491260C)
Retard Cooling
Annealing temperature .......................... Cool slowly from 15001650F (816899C)
Hardening ............................................ Cool rapidly from 17001850F (9271010C)
Tempering ............................................................................. 4001400F(204760C)
65

CHEMICAL
Carbon ......................................................................................................................
Manganese ................................................................................................................
Phosphorus ...............................................................................................................
Sulfur ........................................................................................................................
Silicon .......................................................................................................................
Chromium .................................................................................................................
Molybdenum ............................................................................................................
420F
0.15 Min.
1.25 Max.
0.060 Max.
0.15 Min.
1.00 Max.
12.00/14.00
0.60 Max.
DESCRIPTION
Type 420F stainless steel is easy to machine, grind, and polish, and
has certain anti-galling or nonseizing properties in service. It is used
for parts made on automatic screw machines, such as valve trim,
pump shafts, needle valves, ball check valves, gears, cams, pivots, etc.
This free-machining hardenable steel is used mainly for machined
parts requiring high hardness and good corrosion resistance.
For automatic screw machines, Type 420F stainless steel machines
like SAE 2315 and 2340. In single point turning operations employing
heavy duty equipment, speeds of 90-110 surface feet per minute and
feeds of 0.0008-0.0020 inch are suggested.
Since Type 420F stainless steel should always be used in the hardened condition for optimum corrosion resistance, surfaces must be
free of all scale, which is achieved by pickling, or grinding and
polishing. If pickled after hardening, the parts should be thoroughly
baked at 250-300F for at least one hour to remove acid brittleness.
In the hardened condition, Type 420F stainless steel will resist
corrosion from atmosphere, fresh water, mine water, steam, carbonic
acid, crude oil, gasoline, blood, perspiration, alcohol, ammonia,
mercury, sterilizing solutions, soap, etc. Passivation after machining is
recommended. (It should be noted that Type 420F is not as resistant to
corrosion as an austenitic grade or Type 430F.)
66
PHYSICAL PROPERTIES
Specific gravity ................................................................................................
3
Density-lb/in ....................................................................................................
-6
in/in/F x 10 (32-1200C) ..........................................................................
-6
mm/mm/C x 10 (0-649) ............................................................................
ohm-cir mil/ft ..............................................................................................
microhm-cm ...............................................................................................
Specific heat
Btu/lb/F (32-212F) .....................................................................................
J/kg K ........................................................................................................
7.75
0.28
6.8
12.2
331
55
0.11
460

Annealed
0.2% Yield Strength
ksi .........................................
MPa ..........................................
Tensile Strength
ksi .........................................
MPa ..........................................
Elongation in 2 " (50.8mm), % .......................
Reduction of area % .................................
Brinell hardness ....................................
Annealed &
Cold Drawn
55
379
100
689
95
655
22
50
220
110
758
14
40
228
THERMAL TREATMENT
Initial forging temperature ......................................... 2050-2250F (1130-1231C)
Annealing temperature ........................ Cool slowly from 1550-1650F (843-899C)
Hardening
Heat to 1800-1900F (982-1038C) soak at heat and quench in warm oil.
67
Table 11
FREE-MACHINING STAINLESS STEELS
TRADE NAME DIRECTORY
TYPE
ARMCO
ATLAS
STEELS
303
RP 303
303 MX
303Se
a
304
304
304
316
316
RP 416
416 Se
420F
430F
420F
430F
302 HQ-FM*
303 Project 70
Project 70 303DQ
303
303 Forging Quality
303 Al Modified*
303Se
304 Project 70
316 Project 70
316F
416
CARPENTER
TECHNOLOGY
416 MF
416 MH
416 MX
4 MX
316F
347F Se*
416 Project 70
No. 5
No. 5F*
No. 5 BQ
416 Forging Quality
No. 5 Se
420F
430F
430 FR*
430F Bushing Quality
430F Modified S+Se*
434F*
440F*
440F Se*
Project 70 182-FM*
LTV
STEEL
SLATER
STEELS
CYTEMP
DIV.
CYCLOPS
Multicut 303
303 FQ
303 MM**
303 FQ
303
303 FQ
Multicut 304
304 FQ
Multicut 316
316 FQ
304 MM**
304
316MM**
316
Multicut 416
416 FQ
416 MM**
416 FQ
416 XF
416
416 HH
416 HT
416 FQ
420F
430F
420FM
430 FM
430 FS
* Denotes special analysis not within AlSl composition range. Compositions of special analysis grades are listed in Table 12.
** MM= Maximum machinability
a Types 304 and 316 are not free-machining stainless steels but they are listed because of their wide use for machining applications.
68
Table 12
FREE-MACHINING SPECIAL ANALYSIS STAINLESS STEELS
ALLOY
Mn
302 Hq-FM
0.06
2.00
0.040 0.20
303 Al Mod.
0.15
2.00
347F Se
0.080
2.00
0.050 0.11/
0.16
0.045 -
No. 5F
0.10
1.00
0.060 0.30 Min.
430 FR
430F Mod.
S+Se
434F
0.060 0.050
0.12
1.25
0.020 0.30
0.040 0.10 Min.
0.12
0.040 0.15/
0.40
0.040 0.07 Min.
440F
440F Se
182-FM
1.00
0.95/ 1.00
1.20
0.95/ 1.00
1.20
0.080 1.25/
2.50
0.040 0.030
0.040 0.15/
0.40
Si
Cr
1.00 16.00/
19.00
1.00 17.00/
19.00
1.00 17.00/
19.00
1.00 13.00/
19.50
1.25 17.50
1.00 16.00/
18.00
1.00 16.00/
18.25
1.00 16.00/
18.00
1.00 16.00/
18.00
1.00 17.50/
19.50
Ni
Mo
Other
9.00/
11.00
8.00/
10.00
9.00/
13.00
0.50
1.20/2.40 Cu
0.40/
0.60
-
0.60/1.00 Al
0.50
0.50
0.40/
0.60
0.30
0.60
10XC Min. Cb
0.15 Min. Se
0.15 Min. Se
0.75/
1.25
0.75
0.35 Cu
0.75
0.070 Min. Se
1.50/
2.50
Film-Guide
PRODUCT:
Cine Processor
COMPONENT:
Film-Guide Roller
MATERIAL:
BAR STOCK:
MACHINE TOOL:
1 Inch Round by 12 Feet Long Annealed,

Centerless Ground
Numerical Control Tape Lathe 33A
PRIMARY OPERATIONS:
Form, Drill, Bore, Hone, and Cut-Off
GROSS PRODUCTION:
28 Parts Per Hour
SFPM:
700 Maximum-190 Minimum
RPM:
1800 Maximum-580 Minimum
TOLERANCES:
0.0005 Inch
FINISH:
32 Micro-Inch
69

Stainless Steels For Machining: A Designers' Handbook Series

Uploaded by

Copyright:

Available Formats

Stainless Steels For Machining: A Designers' Handbook Series

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Stainless Steels For Machining: A Designers' Handbook Series

Uploaded by

Copyright:

Available Formats

A DESIGNERS'

Committee of Stainless Steel Producers

Why Upgrade to Stainless Steels?

Selecting a Stainless Steel

Early uses of stainless steels were limited to such applications as

Austenitic stainless steels are those containing chromium, nickel and

Ferritic stainless steels are straight-chromium types identified by 400

Typical of the precipitation hardening grades, identified by UNS

Type 303 Stainless Steel

Hollow Bar 2Inch Square OD and

Acme 3Inch Automatic

Turn, Form, Bore, and Cut-Off

76 Parts Per Hour

161 (Smallest Diameter)

Table 2 continued on next page

Stainless generally is not recommended except when solutions are

There is usually no appreciable attack on Type 304 or 316 as long as

Type 304L or 430 is used.

Type 304 is satisfactory for storing cold phosphoric acid up to 85%

Type 304 can be used at room temperature for concentrations over

Type 304 may be subject to pitting, particularly if some sulfuric acid

Steels in the 300 series generally have good corrosion resistance at

Acetic acid is seldom pure in chemical plants but generally includes

Table 3 continued on next page

handling glacial acetic acid, which would be discolored by Type 304.

Type 304 is generally satisfactory.

Type 316 is usually preferred to Type 304.

Citric, formic and

Type 304 is generally acceptable at moderate temperatures, but Type

From the corrosion standpoint, esters are comparable with organic

Up to about 300F (150C), Type 304 is resistant to fats and fatty

Type 316 is usually used for reactors, fractionating columns, traps,

Tall oil (pulp and

Type 316L is generally required.

The foregoing comments on the use of stainless steels in certain

Type 430 Stainless Steel

0.681 Inch Round Bar, Centerless Ground

Form, Thread, and Cut-Off

Intergranular Corrosion. When austenitic stainless steels are heated

Sensitization may result from slow cooling from annealing

1. Use of stainless steel in the annealed condition.

It should be understood that the above steps are necessary only if

In many processes, isothermal (constant temperature) conditions are

A note of caution about stainless steels at high temperatures in

Table 4 continued on next page

Chemical Analysis % (Max. unless notedotherwise)

Because austenitic stainless steels can be cold worked to high tensile

Ferritic Stainless Steels

Hot and Cold Water Mix Valve

Type 434F Stainless Steel

Coil Stock 0.1195 Inch Round

Form, Drill, and Cut-Off

60 Parts Per Minute

Chemical Analysis % (Max. unless noted otherwise)

Ferritic stainless steels were once regarded as being difficult to weld.

Direct-Read Water Meters

Magnetic Coupling Drive Spindles

Type 316 Stainless Steel