Scribd Logo
Upload

Welcome to Scribd!

  • 731 views

    Aeromodelo f15 - Planos para Depron

    Uploaded by

    mam73
    F15

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Aeromodelo f15 - Planos para Depron

    Uploaded by

    mam73
    731 views1 page
    F15

    Original Title

    Aeromodelo f15 - Planos Para Depron

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    F15

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    731 views1 page

    Aeromodelo f15 - Planos para Depron

    Uploaded by

    mam73
    F15

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    F-15 Park Jet

    3D Foamy
    Specs:

    Copyright 2004 3DFoamy.com.


    All rights reserved.
    Designed and Drawn by:
    Steve Shumate & Levi Jordan
    Updated: 0/19/2004

    All hinging for control surfaces can be packing


    tape or actual hinges. I prefer robart hinge
    points epoxied in place for the added longivity
    and control freeness. CA hinges work well also.

    Cut a "V" groove


    in foam for
    spars. Pull spar
    through groove
    to make round

    Weight 14-18 oz.


    Thrust 14-24 oz.
    Radio 4-5 Chanel
    Area 289.7 in2
    Loading 6.5-8.6 oz/ft2

    CG INFO

    WWW.3DFOAMY.COM

    Start with the recomended


    CG range. You can adjust it
    further back as you become
    more familiar with the jet.

    Sand the fuselage corners round


    with 80 grit sand paper,
    then finish smooth with 200 and 400

    Depron Rails

    Round LE, apply 3M 1" Satin tape for protection

    Prototype Setup/Specs
    Wing area: 289 sq in (effective area, which includes the effect of the wing strakes)
    Span: 28.4 in
    Length: 41.7 in
    Weight RTF: 15.6 oz as shown
    Wing loading: 8.2 oz/ft2 (based on effective wing area)
    Motor: GWS EPS-350 with C gearing
    Battery: 11.1V 1200 mAh Lipo
    Prop: GWS 8x6 SF
    Current draw: 9.7 amps
    Power loading: 101 watts/lb
    Radio equipment: GWS R-6 receiver, GWS Pico and Hitec HS-55 servos, 10 amp ESC
    Flight controls: Wing flaperons, full-flying horizontal stabilizer, twin rudders
    Materials used: Either 6mm Depron or BlueCore fan fold foam

    Push/Pull

    Pull Pull
    Cut Control horns from 1/32"
    ply or a plastic coffee can lid.

    3
    Vacuum Formed Canopy
    (Sand from foam if scratch built)

    1
    1

    Cut hatch after painting


    for radio access

    Foam Nose Cone


    (CNC Cut, Sanded to shape)
    HS-56HB

    www.3DFoamy.com

    Laser cut 1/4" birch motor block.


    Epoxy into plane. DO NOT use
    CA on the moutor mount.

    You might also like